uA78S40PC中文资料
LM78S40CN中文资料
LM78S40Universal Switching Regulator SubsystemGeneral DescriptionThe LM78S40is a monolithic regulator subsystem consisting of all the active building blocks necessary for switching regu-lator systems.The device consists of a temperature com-pensated voltage reference,a duty-cycle controllable oscilla-tor with an active current limit circuit,an error amplifier,high current,high voltage output switch,a power diode and an uncommitted operational amplifier.The device can drive ex-ternal NPN or PNP transistors when currents in excess of 1.5A or voltages in excess of 40V are required.The device can be used for step-down,step-up or inverting switching regulators as well as for series pass regulators.It features wide supply voltage range,low standby power dissipation,high efficiency and low drift.It is useful for any stand-alone,low part count switching system and works extremely well in battery operated systems.Featuresn Step-up,step-down or inverting switching regulators n Output adjustable from 1.25V to 40Vn Peak currents to 1.5A without external transistors n Operation from 2.5V to 40V input n Low standby current drain n 80dB line and load regulationn High gain,high current,independent op amp nPulse width modulation with no double pulsingBlock and Connection DiagramsDS010057-216-Lead DIPDS010057-1Top ViewApril 1998LM78S40Universal Switching Regulator Subsystem©1998National Semiconductor Corporation Ordering InformationPart Number NS Package Temperature Range LM78S40J/883J16A Ceramic DIP−55˚C to+125˚C LM78S40N N16E Molded DIP−40˚C to+125˚C LM78S40CN N16E Molded DIP0˚C to+70˚C2Absolute Maximum Ratings(Note1)If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications.Storage Temperature RangeCeramic DIP−65˚C to+175˚C Molded DIP−65˚C to+150˚C Operating Temperature RangeExtended(LM78S40J)−55˚C to+125˚C Industrial(LM78S40N)−40˚C to+125˚C Commercial(LM78S40CN)0˚C to+70˚C Lead TemperatureCeramic DIP(Soldering,60sec.)300˚C Molded DIP(Soldering,10sec.)265˚C Internal Power Dissipation(Note2)(Note3)16L-Ceramic DIP 1.50W 16L-Molded DIP 1.04W Input Voltage from V IN to GND40V Input Voltage from V+(Op Amp)to GND40V Common Mode Input Range(Comparator and Op Amp)−0.3to V+ Differential Input Voltage(Note4)±30V Output Short CircuitDuration(Op Amp)Continuous Current from V REF10mA Voltage from SwitchCollectors to GND40V Voltage from SwitchEmitters to GND40V Voltage from SwitchCollectors to Emitter40V Voltage from Power Diode to GND40V Reverse Power Diode Voltage40V Current through Power Switch 1.5A Current through Power Diode 1.5A ESD Susceptibility(to be determined)LM78S40Electrical Characteristics(Note5)T A=Operating temperature range,V IN=5.0V,V+(Op Amp)=5.0V,unless otherwise specified.Symbol Parameter Conditions Min Typ Max Units GENERAL CHARACTERISTICSI CC Supply Current V IN=5.0V 1.8 3.5mA(Op Amp Disconnected)V IN=40V 2.3 5.0mAI CC Supply Current V IN=5.0V 4.0mA(Op Amp Connected)V IN=40V 5.5mA REFERENCE SECTIONV REF Reference Voltage I REF=1.0mA Extend−55˚C<T A<+125˚C,Comm0<T A<+70˚C, 1.180 1.245 1.310VIndus−40˚C<T A<+85˚CV R LINE Reference Voltage V IN=3.0V to V IN=40V,0.040.2mV/V Line Regulation I REF=1.0mA,T A=25˚CV R LOAD Reference Voltage I REF=1.0mA to I REF=10mA,0.20.5mV/mA Load Regulation T A=25˚COSCILLATOR SECTIONI CHG Charging Current V IN=5.0V,T A=25˚C2050µAI CHG Charging Current V IN=40V,T A=25˚C2070µAI DISCHG Discharge Current V IN=5.0V,T A=25˚C150250µAI DISCHG Discharge Current V IN=40V,T A=25˚C150350µAV OSC Oscillator Voltage Swing V IN=5.0V,T A=25˚C0.5Vt on/t off Ratio of Charge/ 6.0µs/µs Discharge TimeCURRENT LIMIT SECTIONV CLS Current Limit SenseVoltageT A=25˚C250350mV OUTPUT SWITCH SECTIONV SAT1Output Saturation Voltage1I SW=1.0A(Figure1) 1.1 1.3VV SAT2Output Saturation Voltage2I SW=1.0A(Figure2)0.450.7VLM78S40Electrical Characteristics(Note5)(Continued)T A=Operating temperature range,V IN=5.0V,V+(Op Amp)=5.0V,unless otherwise specified.Symbol Parameter Conditions Min Typ Max Units OUTPUT SWITCH SECTIONh FE Output Transistor CurrentI C=1.0A,V CE=5.0V,T A=25˚C70GainI L Output Leakage Current V O=40V,T A=25˚C10nA POWER DIODEV FD Forward Voltage Drop I D=1.0A 1.25 1.5V I DR Diode Leakage Current V D=40V,T A=25˚C10nA COMPARATORV IO Input Offset Voltage V CM=V REF 1.515mV I IB Input Bias Current V CM=V REF35200nA I IO Input Offset Current V CM=V REF 5.075nA V CM Common Mode VoltageT A=25˚C0V IN–2V RangeV IN=3.0V to40V,T A=25˚C7096dB PSRR Power Supply RejectionRatioOPERATIONAL AMPLIFIERV IO Input Offset Voltage V CM=2.5V 4.015mV I IB Input Bias Current V CM=2.5V30200nA I IO Input Offset Current V CM=2.5V 5.075nA A VS+Voltage Gain+R L=2.0kΩto GND;25250V/mVV O=1.0V to2.5V,T A=25˚CA VS−Voltage Gain−R L=2.0kΩto V+(Op Amp)25250V/mVV O=1.0V to2.5V,T A=25˚CV CM Common Mode VoltageT A=25˚C0V CC−2V RangeCMR Common Mode Rejection V CM=0V to3.0V,T A=25˚C76100dB PSRR Power Supply RejectionV+(Op Amp)=3.0V to40V,T A=25˚C76100dB RatioI O+Output Source Current T A=25˚C75150mA I O−Output Sink Current T A=25˚C1035mA SR Slew Rate T A=25˚C0.6V/µs V OL Output Voltage LOW I L=−5.0mA,T A=25˚C 1.0V V OH Output Voltage High I L=50mA,T A=25˚C V+(Op VAmp)−3VNote1:Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.Electrical specifications do not apply when ordering the device beyond its rated operating conditions.Note2:T J Max=150˚C for the Molded DIP,and175˚C for the Ceramic DIP.Note3:Ratings apply to ambient temperature at25˚C.Above this temperature,derate the16L-Ceramic DIP at10mW/˚C,and the16L-Molded DIP at8.3mW/˚C.Note4:For supply voltages less than30V,the absolute maximum voltage is equal to the supply voltage.Note5:A military RETS specification is available on request.At the time of printing,the LM78S40RETS specification complied with the Min and Max limits in this table.The LM78S40J may also be procured as a Standard Military Drawing.4Typical Performance CharacteristicsDesign FormulasCharacteristic Step-Down Step-Up Inverting UnitsFunctional DescriptionSWITCHING FREQUENCY CONTROLThe LM78S40is a variable frequency,variable duty cycle device.The initial switching frequency is set by the timing capacitor.(Oscillator frequency is set by a single external capacitor and may be varied over a range of100Hz to 100kHz).The initial duty cycle is6:1.This switching fre-quency and duty cycle can be modified by two mechanisms—the current limit circuitry(I pk sense)and the comparator.The comparator modifies the OFF time.When the output voltage is correct,the comparator output is in the HIGH state and has no effect on the circuit operation.If the out-put voltage is too high then the comparator output goes LOW.In the LOW state the comparator inhibits the turn-on of the output stage switching transistors.As long as the comparator is LOW the system is in OFF time.As the out-put current rises the OFF time decreases.As the output current nears its maximum the OFF time approaches its minimum value.The comparator can inhibit several ON cycles,one ON cycle or any portion of an ON cycle.Once the ON cycle has begun the comparator cannot inhibit un-til the beginning of the next ON cycle.The current limit modifies the ON time.The current limit is activated when a300mV potential appears between lead 13(V CC)and lead14(I pk).This potential is intended to re-sult when designed for peak current flows through R SC. When the peak current is reached the current limit is turned on.The current limit circuitry provides for a quick end to ON time and the immediate start of OFF time. Generally the oscillator is free running but the current limit action tends to reset the timing cycle.Increasing load results in more current limited ON time and less OFF time.The switching frequency increases with load current.USING THE INTERNAL REFERENCE,DIODE,AND SWITCHThe internal1.245V reference(pin8)must be bypassed, with0.1µF directly to the ground pin(pin11)of the LM78S40,to assure its stability.V FD is the forward voltage drop across the internal power diode.It is listed on the data sheet as1.25V typical,1.5V maximum.If an external diode is used,then its own for-ward voltage drop must be used for V FD.V SAT is the voltage across the switch element(output tran-sistors Q1and Q2)when the switch is closed or ON.This is listed on the data sheet as Output Saturation Voltage.“Output saturation voltage1”is defined as the switching element voltage for Q2and Q1in the Darlington configu-ration with collectors tied together.This applies to Figure 1,the step down mode.“Output saturation voltage2”is the switching element volt-age for Q1only when used as a transistor switch.This ap-plies to Figure2,the step up mode.For the inverting mode,Figure3,the saturation voltage of the external transistor should be used for V SAT.Typical ApplicationsCharacteristic Condition TypicalValue Output Voltage I O=200mA10V Line Regulation20V≤V I≤30V 1.5mV Load Regulation 5.0mA≤I O 3.0mVI O≤300mAMax Output Current V O=9.5V500mA Output Ripple I O=200mA50mV Efficiency I O=200mA74% Standby Current I O=200mA 2.8mA Note7:For I O≥200mA use external diode to limit on-chip power dissipation.DS010057-3 FIGURE1.Typical Step-Down Regulator andOperational Performance(T A=25˚C)6Typical Applications(Continued)Characteristic Condition TypicalValue Output Voltage I O=50mA25V Line Regulation 5.0V≤V I≤15V 4.0mV Load Regulation 5.0mA≤I O 2.0mVI O≤100mAMax Output Current V O=23.75V160mA Output Ripple I O=50mA30mV Efficiency I O=50mA79% Standby Current I O=50mA 2.6mACharacteristic Condition TypicalValue Output Voltage I O=100mA−15V Line Regulation8.0V≤V I≤18V 5.0mV Load Regulation 5.0mA≤I O 3.0mVI O≤150mAMax Output Current V O=14.25V160mA Output Ripple I O=100mA20mV Efficiency I O=100mA70% Standby Current I O=100mA 2.3mADS010057-4FIGURE2.Typical Step-Up Regulator and Operational Performance(T A=25˚C)DS010057-5FIGURE3.Typical Inverting Regulator andOperational Performance(T A=25˚C)Typical Applications(Continued)DS010057-10 FIGURE4.Pulse Width Modulated Step-Down Regulator(f OSC=20kHz)8Physical Dimensions inches(millimeters)unless otherwise noted16-Lead Ceramic Dual-In-Line Package(J)Order Number LM78S40J/883NS Package Number J16A16-Lead Molded Dual-In-Line Package(N)Order Number LM78S40N or LM78S40CNNS Package Number N16ALIFE SUPPORT POLICYNATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE-VICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI-CONDUCTOR CORPORATION.As used herein:1.Life support devices or systems are devices or sys-tems which,(a)are intended for surgical implant intothe body,or (b)support or sustain life,and whose fail-ure to perform when properly used in accordancewith instructions for use provided in the labeling,can be reasonably expected to result in a significant injury to the user.2.A critical component in any component of a life support device or system whose failure to perform can be rea-sonably expected to cause the failure of the life support device or system,or to affect its safety or effectiveness.National Semiconductor Corporation AmericasTel:1-800-272-9959Fax:1-800-737-7018Email:support@National Semiconductor EuropeFax:+49(0)180-5308586Email:europe.support@Deutsch Tel:+49(0)180-5308585English Tel:+49(0)180-5327832Français Tel:+49(0)180-5329358Italiano Tel:+49(0)180-5341680National Semiconductor Asia Pacific Customer Response Group Tel:65-2544466Fax:65-2504466Email:sea.support@National Semiconductor Japan Ltd.Tel:81-3-5620-6175Fax:81-3-5620-6179L M 78S 40U n i v e r s a l S w i t c h i n g R e g u l a t o r S u b s y s t e mNational does not assume any responsibility for use of any circuitry described,no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.。
2008年TOYOTA自动变速箱配件目录说明书
402A070034311530510520179209211022046500555229337336965975879565ForwardPlanetSun GearV.B.Parts741765992446995777778#1 Sprag036779940030Bushing Kit006Master W/Steels Kit 004Master L/Steels Kit002OHK Kit4032008 AUTOMATIC TRANSMISSION KIT & COMPONENTS CATALOG©2008 PARKER HANNIFIN CORP . ALL RIGHTS RESERVEDCD964974122564332333972124100144873888665654888584251246594604889894795207263268710268898590184580216661650694867120100039O.Dr. Cover7967122812806996966818950757350752********PinionFE077725290289720716847292076Differential Diff.Parts717G730715O.Dr. Direct Drum9352692693752917862886982008 AUTOMATIC TRANSMISSION KIT & COMPONENTS CATALOG©2008 PARKER HANNIFIN CORP. ALL RIGHTS RESERVED *Prefix Letter ‘T’ denotes Toledo-Trans Kit (TTK) Brand Transmission Kits*Prefix Letter ‘B’ denotes Bryco Brand Transmission Kits002.............T87002A........Overhaul Kit, A540E 1988-93.....................................................................................................1..........002.............B87002A.......Overhaul Kit, A540E 1988-93.....................................................................................................1..........002.............TF87002A......Overhaul Kit, A540E 1988-93 (Fiber Pan Gasket).....................................................................1..........002.............T87002AB.....Overhaul Kit, A540H (Camry AWD & RAV-4 4x4) 1989-Up......................................................1..........002.............B87002AB.....Overhaul Kit, A540H (Camry AWD & RAV-4 4x4) 1989-Up......................................................1..........002.............T87002B........Overhaul Kit, A541E 1994-Up....................................................................................................1..........002.............TF87002B......Overhaul Kit, A541E 1994-Up (Fiber Pan Gasket).....................................................................1..........002.............B87000B........Overhaul Kit, A541E 1994-Up....................................................................................................1..........004.............B87004A.......Master L/Steels Kit, A540E 1988-5/1991...................................................................................1..........004.............B87004A.......Master L/Steels Kit, A540E 6/1991-1993...................................................................................1..........004.............B87004B........Master L/Steels Kit, A541E 1994-Up..........................................................................................1..........006.............B87006AA.....Master W/Steels Kit, A540E 1988-5/1991..................................................................................1..........006.............B87006AA.....Master W/Steels Kit, A540E 6/1991-1993..................................................................................1..........008.............B87008A.......Super Kit, A540E 1988-91..........................................................................................................1..........E300...........24009T..........Gasket, A540 Oil Pan..................................................................................................................1..........35168-32020 E300...........24018............Gasket, A540 Oil Pan ( Fiber).....................................................................................................1..........(35168-32020) E300...........24009AT........Gasket, A541E Oil Pan 1994-Up.................................................................................................1..........35168-33010 E300...........24018A..........Gasket, A541E Oil Pan 1994-Up (Fiber).....................................................................................1..........(35168-33010) C302...........24097482......Gasket, A540 Top Cover............................................................................................................1..........35153-33010 G304..........24097481......Gasket, A540E/A540H Overdrive Cover (Rear Cover) 1988-Up..............................................1..........34112-32040 A311...........1994536........O-Ring, A540 Pump 1988-Up.....................................................................................................1..........90301-99024 E326...........24006............Gasket, A540 Filter 1988-Up......................................................................................................1..........35339-32020 E362...........1994137........O-Ring, A540 Servo Cover 1988-93..........................................................................................2..........90301-52003 E362...........1994132........O-Ring, A540 Servo Cover 1994-Up.........................................................................................2..........90301-43005 ...................1994584........O-Ring, A540 Filler Tube 1988-Up.............................................................................................1..........90301-09173 ...................1995509........O-Ring, A540 Speed meter Shaft 1988-Up................................................................................1..........96711-24030175.............6142..............Ring Kit, A540 (2 Metal, 8 PTFE).................................................................................................1..........175.............6142OS.........Ring Kit, A540 (2 Metal, 8 PTFE).................................................................................................1..........A177..........30528............Ring, A540 Forward Clutch (PTFE)............................................................................................3..........35712-32010 A179..........TAW-1344.....Ring, A540 Direct Clutch (Metal)................................................................................................2..........35617-16010 E184...........30524............Ring, A540 Intermediate Shaft (PTFE)........................................................................................1..........35748-32010 G185..........30526............Ring, A540 Overdrive Direct Clutch (PTFE)...............................................................................2..........35617-32011 E195...........30537............Ring, A540 2nd Coast Servo (PTFE) 1988-Up...........................................................................1..........35865-32020 E195...........30527............Ring, A541 2nd Coast Servo (PTFE) 1994-Up...........................................................................1..........35865-33010404B100...........24020............Friction, A540 Reverse Clutch (.059") 33 Teeth (5.60"OD)......................................................6-7........35677-32060B100...........24020A..........Friction, A541A Reverse Clutch (.063") 36 Teeth (5.59 OD) 1994-Up.....................................6-7........35677-33040B100...........240022R........Friction, A540 2nd Brake Clutch (.075") 33 Teeth (5.60"OD) 1992-Up.....................................3..........A106..........24026A..........Friction, A540 Forward Clutch (.060") 40 Teeth (5.00"OD) 1992-Up.......................................5..........35633-33010B106...........24028............Friction, A540 Direct Clutch (.083") 40 Teeth (5.20"OD) 1992-Up............................................3..........35633-20010 119.............24080R..........Friction Module A540E 188-91...................................................................................................1.......... 119.............24080............Friction Module A540E 188-91...................................................................................................1.......... 119.............24080AR.......Friction Module A540E 1991-93.................................................................................................1.......... 119.............24080AT........Friction Module A540E 1991-93.................................................................................................1.......... 119.............24080CR........Friction Module, A540H AWD 1989-Up......................................................................................1.......... 119.............24080C..........Friction Module, A540H AWD 1989-Up......................................................................................1.......... 119.............24080BR........Friction Module, A541E 1994-Up................................................................................................1..........A122..........25821C..........Steel, A540 Forward Clutch (.071") 4.10"ID (8 Teeth) 1988-91................................................4..........35634-12040A122..........25821A..........Steel, A540 Forward Clutch (.063") 8 Teeth (4.10"ID) 1992-Up...............................................4..........35634-33010A122..........25821B..........Steel, A540 Forward Clutch (.055") 8 Teeth (4.10"ID) 1992-Up..............................................1-5........35634-33020A122..........24027............Steel, A540 Direct Clutch (.071") 6 Notched Teeth (4.10"ID) 1988-91......................................1..........35634-32020A122..........24027A..........Steel, A540 Direct Clutch (.055") 6 Teeth (4.10"ID) 1992-Up....................................................1..........35634-33030A122..........24027B..........Steel, A540 Direct Clutch (.079") 6 Teeth (3 Teeth Are Notched) 4.10"ID................................2-3........35647-33020F122...........24021............Steel, A540 Overdrive Direct Clutch (.118") 4.10"ID (24 Teeth) 1989-93.................................2..........34615-20010F122...........24021A..........Steel, A541E Overdrive Direct Clutch (.071") 24 Teeth (4.10"ID) 1994-Up...............................2..........34615-33030 ...................25829............Steel, A540 Differential Clutch (.063") 3.60"ID (30 Teeth) 1988-Up..........................................11.........41474-32011B124...........24029............Steel, A540 2nd Brake Clutch (.071") 12 Teeth (4.60"ID) 1988-Up...........................................3..........35648-32030B124...........24025A..........Steel, A541E 2nd Brake Clutch (.071") 10 Teeth (4.86"ID) 1994-Up (Wide Splined)................4..........35648-33010C130...........24029A..........Steel, A541E Reverse Clutch (.063") 10 Teeth (4.86"ID) 1994-Up (Narrow Spline).................6..........35648-33020 139.............24081............Steel Module, A540E 1988-91....................................................................................................1.......... 139.............24081A..........Steel Module, A540E 1991-93....................................................................................................1.......... 139.............24081C..........Steel Module, A540H AWD 1989-Up..........................................................................................1.......... 139.............24081B..........Steel Module, A541E 1994-Up....................................................................................................1..........E010...........25842B..........Filter, A540E/A540H 1988-Up.....................................................................................................1..........E010...........24040B..........Filter, A541E 1994-96.................................................................................................................1..........011.............24041............Filter Kit, A540E/A540H 1988-94................................................................................................1.......... 011.............24041A..........Filter Kit, A540E/A540H 1988-94 (Fiber Pan Gasket)................................................................1.......... 011.............24043............Filter Kit, A541E 1994-Up...........................................................................................................1..........G039..........24033............Bushing, A540 Overdrive Direct Drum (Rear)...........................................................................1..........A046..........24032............Bushing, A540 Direct Drum........................................................................................................1..........B050...........24035............Bushing, A540 Input Hub............................................................................................................1..........B052...........24031............Bushing, A540 Sun Gear...........................................................................................................2..........2008 AUTOMATIC TRANSMISSION KIT & COMPONENTS CATALOG©2008 PARKER HANNIFIN CORP. ALL RIGHTS RESERVED4054062008 AUTOMATIC TRANSMISSION KIT & COMPONENTS CATALOG ©2008 PARKER HANNIFIN CORP. ALL RIGHTS RESERVEDE216...........24073............Washer, A540 Overdrive Planet To Overdrive Drum.................................................................1..........34737-3310...................24074............Washer, A540E Planetary Carrier Sun Gear 1988-93...............................................................1..........35739-32020...................24074A..........Washer, A541E Planet Carrier #3 1994-Up................................................................................1..........35739-33010...................24072............Washer, A540E Planetary Carrier Front 1988-93......................................................................1..........35738-32020...................24072A..........Washer, A541E Planetary# 2 1994-Up ......................................................................................1..........35738-33020...................24071............Washer,A540E Planetary Carrier Rear 1988-93.......................................................................1..........35738-32030...................24071A..........Washer, A541E Planetary# 3 1994-Up ......................................................................................1..........35738-33010E425...........S-151.............Solenoid, A540 Lock-Up 1988-..................................................................................................1..........85420-32110E425...........89758............Solenoid, A540E, A540H Lock Up 1989-Up ...............................................................................1..........85420-32110E425...........S-118.............Solenoid, A541E Lock-Up 1994-04 OEM....................................................................................1..........35240-33010E420...........S-152.............Solenoid, A540E Shift 1, 2 1988-...............................................................................................1..........85420-32091E420...........89757............Solenoid, A540E, A540H Shift 1988-93.....................................................................................1..........85420-32091E420...........S-110.............Solenoid, A541E Shift 1, 2 1994- OEM.......................................................................................1..........85420-33010E420...........89757A..........Solenoid, A541E Shift 1994-Up ..................................................................................................1..........85420-33010B642...........24085............Sprag Assembly, A540 (4 1/2"OD).............................................................................................1..........35790-320312008 AUTOMATIC TRANSMISSION KIT & COMPONENTS CATALOG©2008 PARKER HANNIFIN CORP. ALL RIGHTS RESERVED407。
UA78M33CDCYG3中文资料
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
Copyright © 1976–2005, Texas Instruments Incorporated
元器件交易网
µA78M00 SERIES POSITIVE-VOLTAGE REGULATORS
SLVS059P – JUNE 1976 – REVISED OCTOBER 2005
(2) For packages with exposed thermal pads, such as QFN, PowerPAD™, or PowerFLEX, θJP is defined as the thermal resistance between the die junction and the bottom of the exposed pad.
Absolute Maximum Ratings(1)
over virtual junction temperature range (unless otherwise noted)
VI
Input voltage
TJ
Operating virtual junction temperature
UPD78F9202MA中文资料
User’s ManualμPD78F9200 μPD78F9201 μPD78F9202 μPD78F9500μPD78F9501 μPD78F950278K0S/KU1+8-Bit Single-Chip Microcontrollers©Printed in JapanDocument No. U18172EJ3V0UD00 (3rd edition) Date Published November 2009 NS2006深圳创泰芯电子 朱先生 Ｑ３２６６６０６８４６User’s Manual U18172EJ3V0UD6Conventions Data significance: Higher digits on the left and lower digits on the right Active low representation: ××× (overscore over pin or signal name)Note : Footnote for item marked with Note in the text Caution :Information requiring particular attentionRemark : Supplementary informationNumerical representation: Binary ... ×××× or ××××BDecimal ... ×××× Hexadecimal ... ××××HRelated Documents The related documents indicated in this publication may include preliminary versions. However, preliminary versions are not marked as such.Documents Related to DevicesDocument NameDocument No. 78K0S/KU1+ User’s ManualThis manual 78K/0S Series Instructions User’s ManualU11047EDocuments Related to Development Software Tools (User’s Manuals)Document NameDocument No.Operation U17391ELanguage U17390E RA78K0S Ver.2.00 Assembler PackageStructured Assembly LanguageU17389EOperation U17416ECC78K0S Ver.2.00 C CompilerLanguage U17415EOperation U18601E SM+ System SimulatorUser Open InterfaceU18212E ID78K0S-QB Ver.3.00 Integrated Debugger OperationU18493E PM+ Ver.6.30U18416EDocuments Related to Development Hardware Tools (User’s Manuals)Document NameDocument No. QB-78K0SKX1 In-Circuit EmulatorU18219E QB-MINI2 On-Chip Debug Emulator with Programming FunctionU18371EDocuments Related to Flash Memory Writing (User’s Manuals)Document NameDocument No. PG-FP5 Flash Memory ProgrammerU18865EQB-Programmer Programming GUIOperationU18527ECaution The related documents listed above are subject to change without notice. Be sure to use the latestversion of each document for designing.<R><R>Other Related DocumentsDocument Name Document No. SEMICONDUCTOR SELECTION GUIDE - Products and Packages - X13769X Semiconductor Device Mount Manual NoteQuality Grades on NEC Semiconductor Devices C11531ENEC Semiconductor Device Reliability/Quality Control System C10983EGuide to Prevent Damage for Semiconductor Devices by Electrostatic Discharge (ESD) C11892ENote See the “Semiconductor Device Mount Manual” website (/pkg/en/mount/index.html).Caution The related documents listed above are subject to change without notice. Be sure to use the latest version of each document for designing.User’s Manual U18172EJ3V0UD 7User’s Manual U18172EJ3V0UD14CHAPTER 1 OVERVIEW1.1 FeaturesO 78K0S CPU coreO Minimum instruction execution time: 0.2 μs (with 10 MHz@4.0 to 5.5 V operation) O Clock• High-speed system clock … Selected from the following three sources- Ceramic/crystal resonator: 2 to 10 MHz - External clock:2 to 10 MHz - High-speed internal oscillatorμPD78F920x: 8 MHz ±3% (−10 to +70°C), 8 MHz ±5% (−40 to +85°C) μPD78F950x: 8 MHz ±2% (−10 to +85°C), 8 MHz ±5% (−40 to +85°C)• Low-speed internal oscillator 240 kHz (TYP.) … Watchdog timer, timer clock in intermittent operation O I/O ports: 8 (CMOS I/O: 7, CMOS input: 1) O Timer: 3 channels • 16-bit timer/event counter Note: 1 channel … Timer output × 1, capture input × 2 • 8-bit timer: 1 channel … PWM output × 1• Watchdog timer:1 channel … Operable with low-speed internal oscillation clockO 10-bit resolution A/D converter Note: 4 channelsO On-chip power-on-clear (POC) circuit (A reset is automatically generated when the voltage drops to 2.1 V (TYP.)or below)O On-chip low voltage detector (LVI) circuit (An interrupt/reset (selectable) is generated when the detection voltage is reached)• Detection voltage: Selectable from ten levels between 2.35 and 4.3 V O Single-power-supply flash memory • Flash self programming enabled• Software protection function: Protected from outside party copying (no flash reading command) • Time required for writing by dedicated flash memory programmer: Approximately 3 seconds (4 KB) ∗ Flash programming on mass production lines supported O Safety function• Watchdog timer operated by clock independent from CPU … A hang-up can be detected even if the system clock stops • Supply voltage drop detectable by LVI… Appropriate processing can be executed before the supply voltage drops below the operation voltage • Equipped with option byte function… Important system operation settings set in hardwareNote μPD78F920x only<R> <R> <R>CHAPTER 1 OVERVIEWUser’s Manual U18172EJ3V0UD15O Assembler and C language supported O Enhanced development environment• Support for full-function emulator (IECUBE), simplified emulator (MINICUBE2), and simulator O Supply voltage: V DD = 2.0 to 5.5 V∗ Use these products at V DD = 2.2 to 5.5 V because the POC detection voltage (V POC ) is the supply voltagerange.O Operating temperature range: T A = −40 to +85°C1.2 Ordering InformationPart NumberμPlease refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) p u b l i s h e d b yNEC Corporation to know the specification of quality grade on the devices and its recommended applications.[Part number list]μ PD78F9200MA-CAC-A μ PD78F9500MA-C A C -A μ PD78F9201MA-CAC-A μ PD78F9501MA-C A C -A μ PD78F9202MA-CAC-Aμ PD78F9502MA-C A C -A<R> <R> <R>CHAPTER 1 OVERVIEWUser’s Manual U18172EJ3V0UD161.3 Pin Configuration (Top View)1.3.1 μPD78F920x10-pin plastic SSOPV SS Note V DD NoteANI0 to ANI3: Analog inputTI000, TI010: Timer input INTP0, INTP1: External interrupt input TO00, TOH1: Timer outputP20 to P23: Port 2 V DD Note2: Power supplyP30, P34: Port 3 V SSNote1: GroundP40, P43: Port 4X1, X2: Crystal oscillator (X1 input clock)RESET: ResetNotes 1. In μPD78F920x, V SS functions alternately as the ground potential of the A/D converter. Be sure toconnect V SS to a stabilized GND (= 0 V).2. In μPD78F920x, V DD functions alternately as the A/D converter reference voltage input. When using theA/D converter, stabilize V DD at the supply voltage used (2.7 to 5.5 V).1.3.2 μPD78F950x10-pin plastic SSOPV VINTP0, INTP1: External interrupt input TOH1:Timer outputP20 to P23: Port 2 V DD : Power supply P30, P34: Port 3 V SS : Ground P40, P43: Port 4 EXCLK: External Clock Input Reset(Main System Clock)<R>CHAPTER 1 OVERVIEWUser’s Manual U18172EJ3V0UD171.4 78K0S/Kx1+ Product LineupThe following table shows the product lineup of the 78K0S/Kx1+.Notes 1. Use these products in the following voltage range because the detection voltage (V POC ) of the power-on-clear (POC) circuit is the supply voltage range.Standard product, (A) grade product: 2.2 to 5.5 V, (A2) grade product: 2.26 to 5.5 V 2. μ PD78F950x does not support the crystal/ceramic oscillation. 3. The product without A/D converter (μ PD78F950x) in the 78K0S/KU1+ is not supported. 4. The product without A/D converter (μ PD78F95xx) is provided for the 78K0S/KU1+ and 78K0S/KY1+respectively.5. There are 2 and 4 factors for the products without A/D converter in the 78K0S/KU1+ and 78K0S/KY1+,respectively.<R><R>CHAPTER 1 OVERVIEWUser’s Manual U18172EJ3V0UD181.5 Block Diagram1.5.1 μPD78F920xTO00/TI010/P21TI000/P20TOH1/P20INTP0/P21INTP1/P32Notes 1. In μPD78F920x, V DD functions alternately as the A/D converter reference voltage input. When using theA/D converter, stabilize V DD at the supply voltage used (2.7 to 5.5 V).2. In μPD78F920x, V SS functions alternately as the ground potential of the A/D converter. Be sure toconnect V SS to a stabilized GND (= 0 V).CHAPTER 1 OVERVIEWUser’s Manual U18172EJ3V0UD191.5.2 μPD78F950xTOH1/P20INTP0/P21INTP1/P32<R> 深圳创泰芯电子 朱先生 Ｑ３２６６６０６８４６。
康明斯发电机组 QSK78系列柴油发动机说明书
Continuous Rating 50Hz kVA (kW)
2250 (1800)
C3000 D5 3000 (2400)* 2750 (2200) 2475 (1980)
*Note: Rating is with a Remote Cooled Configuration
Emissions Compliance TA LUFT
Fuel Filter
Air Cleaner Type Lube Oil Filter Type(s) Cooling System
Alternator Specifications
Design Stator Rotor Insulation System Standard Temperature Rise Exciter Type Phase Rotation Alternator Cooling AC Waveform Total Harmonic Distortion Telephone Influence Factor (TIF) Telephone Harmonic Factor (THF)
• 240 V control anti-condensation
• Temperature sensor - RTDs,
• Temperature sensor – alternator bearing RTD Exhaust System
• Differential current transformers
Warranty • 2 years warranty • 5 years warranty • 10 year major component warranty
Our energy working for you.™
NEC单片机解密研究
NEC单片机解密研究NEC/瑞萨单片机系列破解研究－－早期Flash/ROM系列|目前，NEC第一代FLASH MCU制品分别采用0.35um和0.25um 工艺或 MASKROM制作，目前能够得到全面完美破解：早期78K0s:1. 型号命名规则：78F90**uPD789022,uPD789024,uPD789025,uPD789026,uPD78F9026uPD789046, uPD78F9046uPD789052, uPD789062, uPD78E9860, uPD78E9861,uPD789071,uPD789072,uPD789074 uPD78F9076uPD789086,uPD789088 uPD78F90882. 型号命名规则：78F91**uPD789101,uPD789102,uPD789104,uPD789111,uPD789112, uPD789114, uPD78F9116uPD789121,uPD789122,uPD789124,uPD789131,uPD789132, uPD789134, uPD78F9136uPD789166,uPD789167,uPD789176,uPD789177uPD78F91773. 78K0s/Kx1+ Lowpin 系列型号命名规则：78F92** 或78F95**uPD78F9200,uPD78F9201,uPD78F9202,uPD78F9500,uPD78F9501,uPD78F9502,uPD78F9210,uPD78F9211,uPD78F9212,uPD78F9510,uPD78F9511,uPD78F9512,uPD78F9221,uPD78F9222,uPD78F9224,uPD78F9232,uPD78F92344. 型号命名规则：78F93**uPD789304,uPD789306,uPD789314,uPD789316,uPD78F9314, uPD78F9316uPD789322,uPD789324,uPD789326,uPD789327,uPD78F93285. 型号命名规则：78F94**uPD789405,uPD789406,uPD789407,uPD789415,uPD789416, uPD789417, uPD78F9418uPD789425,uPD789426,uPD789435,uPD789436,uPD78F9436uPD789445,uPD789446,uPD789455,uPD789456,uPD78F9456uPD789462,uPD789464,uPD789466,uPD789467,uPD78F9468uPD789477,uPD789478,uPD789479,uPD789488,uPD789489, uPD78F9478，uPD78F9479, uPD78F9488，uPD78F9489,6. 型号命名规则：78F98**uPD789830,uPD789832,uPD789833,uPD789834,uPD789835 uPD78F9835uPD789841,uPD789842 uPD78F9842uPD789800 uPD78F9801uPD789881 uPD78F9882uPD789860,uPD789861,uPD789862uPD78E9860A,uPD78E9861A早期78K0:1. 型号命名规则：78F00**uPD780021,uPD780022,uPD780023,uPD780024,uPD780031,uPD780032,uPD780033,uPD780034,uPD78F0034uPD780053,uPD780054,uPD780055,uPD780056,uPD780058, uPD78F0058uPD780065,uPD780076,uPD780078,uPD78F0066,uPD78F0078,2. 78K0/Kx1 型号命名规则： 78F01**uPD780101,uPD780102,uPD780103, uPD78F0103,uPD780111,uPD780112,uPD780113,uPD780114,uPD78F0114,uPD780131,uPD780132,uPD780133,uPD780134,uPD780136, uPD780138, uPD78F0134,uPD78F0138,uPD780143,uPD780144,uPD780146,uPD780148,uPD78F0148,3. 78K0/Kx1+ 型号命名规则：78F01**H 或 7801**HuPD780101H,uPD780102H,uPD780103H, uPD78F0103H,uPD780111H,uPD780112H,uPD780113H,uPD780114H, uPD78F0114H,uPD780131H,uPD780132H,uPD780133H,uPD780134H,uPD7 80136H,uPD780138H, uPD78F0134H,uPD78F0138H,uPD780143H,uPD780144H,uPD780146H,uPD780148H, uPD78F0148H,例： uPD780102H 为著名的SONY PSP游戏机电池加密芯片4. 型号命名规则： 78F02**uPD780232,uPD780233, uPD78F0233,5. 型号命名规则： 78F03**uPD780306,uPD780308, uPD78P0308,uPD780316,uPD780318,uPD780326, uPD780328,uPD780336, uPD780338, uPD78F0338,uPD780343,uPD780344,uPD780353, uPD780354, uPD78F0354,7. 型号命名规则： 78F07**uPD78F0714,8. 型号命名规则： 78F08**uPD780861,uPD780862, uPD78F0862A,uPD780822,uPD780824,uPD780826,uPD780828,uPD78F0822B,uPD78F0828A,9. 型号命名规则： 78F09**uPD780957 uPD78F0958uPD780982,uPD780983,uPD780984,uPD780986,uPD780988, uPD78F0988A10. ASSP 型号命名规则： 78F80**uPD788004,uPD788005,uPD788006,uPD78F8004,uPD78F8005,uPD78F8006,全部V850:1. V850/Sx1/2/3 型号命名规则：70F30**uPD703014,uPD703015,uPD703017,uPD70F3015,uPD70F3017,uPD703030,uPD703031,uPD703032,uPD703033uPD70F3030,uPD70F3032,uPD70F3033uPD703034,uPD703035,uPD703036,uPD703037uPD70F3035,uPD70F3036,uPD70F3037uPD703068,uPD703069,uPD703088,uPD703089,uPD70F3089uPD780065,uPD780076,uPD780078,uPD78F0066,uPD78F0078,早期V850ES:1. V850ES/Sx1/2 型号命名规则：70F32** 汽车仪表盘uPD703200,uPD703201,uPD703204,uPD70F3201,uPD70F3204,uPD703249,uPD703260,uPD703261,uPD703262,uPD703263, uPD70F3261,uPD70F3263uPD703264,uPD703265,uPD703266,uPD70F3264,uPD70F3265,uPD70F3266,uPD703252,uPD703270,uPD703271,uPD703272,uPD703273, uPD70F3271,uPD70F3273uPD703274,uPD703275,uPD703276,uPD70F3274,uPD70F3275,uPD70F3276,uPD703253,uPD703280,uPD703281,uPD703282,uPD703283, uPD70F3281,uPD70F3283uPD703284,uPD703285,uPD703286,uPD70F3284,uPD70F3285,uPD70F3286,2. V850ES/Fx2 型号命名规则： 70F32** 工业控制，汽车电子uPD703230,uPD703231,uPD703232,uPD703233,uPD703234, uPD703235uPD70F3231,uPD70F3232,uPD70F3233,uPD70F3234,uPD70 F3235,uPD70F3236,uPD70F3237,uPD70F3238,uPD70F32393. V850ES/Ix 型号命名规则： 70F33** 70F37** 电机控制，空调变频器uPD703327,uPD703329, uPD70F3329uPD70F3713,uPD70F3714,4. V850ES/Kx1+ 型号命名规则： 70F33**uPD703302,uPD703313,uPD70F3302,uPD70F3306, uPD70F3308,uPD70F3311, uPD70F3313,uPD70F3316, uPD70F33185. V850ES/Hx2 型号命名规则： 70F37**uPD70F3700,uPD70F3701, uPD70F3702,uPD70F3703, uPD70F3704,uPD70F3706,uPD70F3707,uPD70F3710, uPD70F3711,uPD70F3712,6. V850ES/Jx2 型号命名规则： 70F37**uPD70F3715,uPD70F3716, uPD70F3717,uPD70F3718, uPD70F3719,uPD70F3720,uPD70F3721, uPD70F3722,uPD70F3723, uPD70F3724,7. V850ES/Kx2 型号命名规则： 70F37**uPD70F3726,uPD70F3728, uPD70F3729,uPD70F3731, uPD70F3732,uPD70F3733, uPD70F3734,8. V850ES/Sx3 型号命名规则： 70F33**uPD70F3333,uPD70F3334,uPD70F3335,uPD70F3336,uPD70F3340,uPD70F3341, uPD70F3342,uPD70F3343,uPD70F3344,uPD70F3345, uPD70F3346,uPD70F3347, uPD70F3348uPD70F3350,uPD70F3351, uPD70F3352,uPD70F3353, （奔驰C180~C260导航仪CAN协议IC）uPD70F3354,uPD70F3355, uPD70F3356,uPD70F3357, uPD70F3358uPD70F3364,uPD70F3365, uPD70F3366,uPD70F3367, uPD70F3368早期V850E1:1. V850E/Mx1/2/3 型号命名规则： 70F31**uPD703101,uPD703102, uPD70F3102uPD703105,uPD703106, uPD703107, uPD70F3107uPD703114,uPD703116, uPD703183,uPD703185,uPD703186, uPD70F3114,uPD70F3116, uPD70F3184,uPD70F3186, uPD703136,uPD703132, uPD703133,uPD703134, uPD70F31342. 安全气囊IC V850E/RS1 型号命名规则： 70F34**uPD70F3400,uPD70F3401上述型号解密周期为15~30天，企鹅是二六七一三六八七二四NEC第二代全FLASH MCU制品分别采用0.25/0.15um(MF2)工艺制作，称为ALL FLASH品。
78K0系列用户手册(指令集)
To our customers,Old Company Name in Catalogs and Other DocumentsOn April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding.Renesas Electronics website: April 1st, 2010Renesas Electronics CorporationIssued by: Renesas Electronics Corporation ()Send any inquiries to /inquiry.Notice1. All information included in this document is current as of the date this document is issued. Such information, however, issubject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website.2. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rightsof third parties by or arising from the use of Renesas Electronics products or technical information described in this document.No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others.3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.4. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation ofsemiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information.5. When exporting the products or technology described in this document, you should comply with the applicable export controllaws and regulations and follow the procedures required by such laws and regulations. You should not use RenesasElectronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations.6. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronicsdoes not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.7. Renesas Electronics products are classified according to the following three quality grades: “Standard”, “High Quality”, and“Specific”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particularapplication. You may not use any Renesas Electronics product for any application categorized as “Specific” without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific” or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is “Standard” unless otherwiseexpressly specified in a Renesas Electronics data sheets or data books, etc.“Standard”: Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots.“High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically designed for life support.“Specific”: Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcareintervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life.8. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics,especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges.9. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products havespecific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of aRenesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you.10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmentalcompatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of RenesasElectronics.12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in thisdocument or Renesas Electronics products, or if you have any other inquiries.(Note 1) “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.(Note 2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.用户手册适用于78K/0系列78K/0系列指令©NEC Electronics China 2007日本印制文档编号.U12326CA4V0UM00(第四版)发行日期2007年7月NCP(K)[备忘录]用户手册U12326CA4V0UM 2CMOS设备的注释①ESD防护措施如果MOS设备周围有强电场，将会击穿氧化栅极，从而影响设备的运行。
义隆中文资料 EM78P447S中文
8位 OTP 微控制器
产品规Байду номын сангаас书
版本 1.7
义隆电子股份有限公司
2009.11
本文内容是由英文规格书翻译 而来，目的是为了您的阅读更 加方便。它无法跟随原稿的更 新，文中可能存在翻译上的错 误，请您参考英文规格书以获 得更准确的信息。
商标告知:
IBM 为一个注册商标，PS/2 是 IBM 的商标之ㄧ.。
4.5 复位和唤醒 ..................................................................................................... 16
4.5.1 复位................................................................................................................... 16 4.5.2 状态寄存器的 RST, T, 和 P 的状态 ....................................................................... 20
Korea:
Elan Korea Electronics Company, Ltd.
301 Dong-A Building 632 Kojan-Dong, Namdong-ku Incheon City, KOREA Tel: +82 32 814-7730 Fax:+82 32 813-7730
深圳分公司:
香港分公司:
义隆电子（香港）有限公司 九龙观塘巧明街 95 号世达中心 19 楼 A 室 电话：+852 2723-3376 传真：+852 2723-7780
华硕 M5A78L USB3 主板用户手册
之損害。 B. 自行拆裝、修理、或將產品送至非華碩認証之維修點進行檢測維修。 C. 用戶擅自或請第三人修改、修復、變更規格及安裝、添加、擴充非本公司原廠銷售、授權
ii
三年質保
全國聯保
請用剪刀沿虛線剪下
華碩產品質量保證卡
尊敬的華碩產品用戶：
首先非常感謝您選用華碩公司產品，讓我們有機會向您提供優質的服務。為了使我們的服務讓您 更滿意，在購買後請您認真閱讀此說明並妥善保存此質量保證卡。
保修說明注意事項：
一、 請將此質量保證卡下方的用戶資料填寫完整，並由最終直接經銷商加蓋印章，如果沒有加蓋印 章，請找原購買處補蓋以保障您的權益。請務必保留購買發票或複印件，否則華碩公司將以產 品的出廠日期為參照進行保修。
Motherboard
M5A78L/USB3
用戶手冊
C6588 第一版（V1） 2011 年 4 月發行
版權所有‧不得翻印 © 2011 華碩電腦 本產品的所有部分，包括配件與軟件等，其相關知識產權等歸華碩電腦公司（以下簡稱華
碩）或授權華碩使用的相關主體所有，未經權利主體許可，不得任意地仿製、拷貝、摘抄或轉 譯。本用戶手冊沒有任何型式的擔保、立場表達或其它暗示。若有任何因本用戶手冊或其所提到 之產品信息，所引起直接或間接的數據流失、利益損失或事業終止，華碩及其所屬員工恕不為其 擔負任何責任。除此之外，本用戶手冊所提到的產品規格及信息只做參考，內容亦會隨時更新， 恕不另行通知。
關於這本用戶手冊...................................................................................................................... ix 用戶手冊的編排方式...................................................................................................... ix 提示符號.............................................................................................................................. ix 跳線帽及圖示說明........................................................................................................... ix 哪裡可以找到更多的產品信息.................................................................................... x
快速设置指南 - 32S4 40S4 电视说明书
QUICK SETUP GUIDE Before using the TV, please read this guide thoroughly andretain it for future reference. 32S4 40S4Englishsymbol is AC voltage.Disposal of Used Electrical & Electronic EquipmentPackaging and electrical goods should be recycled appropriately, andnot treated as household waste. Please dispose of this equipment atyour applicable collection point for the recycling of electrical & electronicequipment waste. By ensuring the correct disposal of this product,you will help prevent potentially hazardous to the environment and tohuman health, which could otherwise be caused by unsuitable wastehandling of this product. The recycling of materials will help conservenatural resources. Please do not therefore dispose of your old electricaland electronic equipment with your household waste. For more detailedinformation about recycling of this product, please contact your local cityoffice, your household waste disposal service or the shop where youpurchased the product.Educating children about the dangers of climbing on furniture to reach the television set or its controls.If your existing television set is being retained or relocated, the same considerationsas above should be applied.lightly dampened cloth for cleaning.4. Wall BracketAfter market brackets may be available to purchase locally. Please refer to the specification page for dimensions.5. Water and MoistureAvoid dripping or splashing of liquids onto the product. Objects filled with liquids, such as vases, should not be placed on the product.6. SettingDo not place this TV on an unstable cart, stand or table. Placing the TV on an unstable base can cause the TV to fall, resulting in serious personal injuries as well as damage to the TV. Use only a cart, stand, bracket or table recommended by the manufacturer or salesperson.7. VentilationSlots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the TV and to protect it from overheating. Do not cover the ventilation openings in the cabinet and never place the set in a confined space such as built-in cabinet unless proper ventilation is provided. Leave a minimum 10cm gap all around the unit, the rear of the TV should be 6cm away from the wall.8. Power SourceThis TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your appliance dealer or local power company.9. Power-Cord ProtectionPower- supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plug, wall outlets, and the point where they exit from the TV. MAIN plug is used as the disconnect device, the disconnect device shall remain readily operable.10. LightningFor added protection for this TV during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning or power-line surge.11. Power LinesAn outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. While installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 12. OverloadingDo not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.13. Object and Liquid EntryNever push objects of any kind into this TV through openings as they may touch dangerous voltage points or short-out parts that could result in fire or electric shock. Never spill liquid of any kind on or into the TV.14. Outdoor Antenna GroundingIf an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.15. ServicingDo not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.16. Damage Requiring ServiceUnplug the TV from the wall outlet and refer servicing to qualified service personnel under the following conditions:(a) When the power - supply cord or plug is damaged.(b) If liquid has been spilled, or objects have fallen into the TV.(c) If the TV has been exposed to rain or water.(d) If the TV does not operate normally by following the operating instructions. Adjustonly those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to its normal operation.(e) If the TV has been dropped or the cabinet has been damaged.(f) When the TV exhibits a distinct change in performance - this indicates a need forservice.17. Replacement PartsWhen replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.18. Safety CheckUpon completion of any service or repair to the TV, ask the service technician to perform safety checks to determine that the TV is in safe operating condition.19. HeatThe product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.20. FireThe product should be situated away from naked flame sources such as lighted candle.21. Off-gassingThe TV smells of plastic is normal and will dissipate over time.Accessories ListThe following accessories are included with TV:Turning the TV on for the First Time .............................................................................13Specifications ...............................................................................................................14Other Information..........................................................................................................15 The accessories may be different from the list above due to different models, countries / regions, please refer to the actual accessory bag.1.Carefully place your TV face-down on a soft, flat surface to prevent damage to theTV or scratching to the screen.2.Remove the Base Stand from the accessory bag and then insert the stand into thebottom slots of the TV.3.Secure the Base Stand to the TV with the screws in accessory tightly.(ST4×14F) × 4(32")(ST4×20F) × 4(40")• The diameter and length of the screws differ depending on the wall mount bracket model.• Wall mount bracket is optional, your device may not have wall mount bracket, please refer to the actual accessories.The Picture is Only for Reference.Powering on the TV requires several seconds to load programs. Do not rapidly turn the TV off as it may cause the TV work abnormally.Wireless router with DHCPLAN CableWireless LAN Adapter built-in TV setYou must use the built-in Wireless LAN Adapter to use a wireless network because the set doesn’t support external USB network adapter.If the wireless router supports DHCP , your TV can connect more easily to the wireless network.If you apply a security system other than the systems listed below, it will not work with the TV.Security system:WPA,WEP ,WPA2.In order to guarantee smooth network, the distance between router and TV should be less than 10 meters.Wireless setupConnect your TV to your network wirelessly, you need a wireless router or modem. See the illustration below.·The built-in Wireless LAN Adapter supports the IEEE 802.11a/b/g/n/ac communication protocols. We recommend using IEEE 802.11n router. Low transfer rates for b/g may have the influence on the quality of streamed videos and other media.LThe button information will vary depending on the remote control model. The Picture is Only for Reference.Check information according to the actualThe button information will vary depending on the remote control model. The Picture is Only for Reference.Check information according to the actualRemote Control Operation RangeProduct image is only for reference, actual product may vary in appearance.Handling the BatteriesIncorrect use of batteries may cause corrosion or battery leakage, which could cause fire, personal injury or damage to property.Only use the battery type indicated in this manual.Do not mix old and new batteries or different types of batteries.Do not dispose of used batteries as domestic waste. Dispose of them in accordance with local regulations.The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. Copyright 1992-2019 Dolby Laboratories. All rights reserved.Manufactured under license from THAT Corporation. THAT Corporation, dbx-tv, Total Sonics, Total Surround and Total Volume are registered trademarks of THAT Corporation. Total Technology is a trademark of THAT Corporation.Freeview Plus service only available in Australia territories.What is Freeview Plus?Freeview Plus is a new television service delivered via broadband providing a state of the art Electronic Program Guide (EPG) and seamless access to catch-up TV across the free-to-air networks with the simple press of a button.How does it work?First ensure the TV is connected to internet and an antenna system. Then when you’re watching TV, you’ll briefly see a prompt at the top left of the screen. Press the ‘Green’ button on your remote to launch Freeview Plus. More information about Freeview Plus can be found on .au/。
TS78M18A中文资料
TS78M00A series3-Terminal Medium Current Positive Voltage RegulatorPin assignment:1. Input2. Ground3. Output (Heatsink surfaceconnected to Pin 2)Voltage Range 5V to 24V Output Current up to 0.5AGeneral DescriptionThe TS78M00A Series positive voltage regulators are identical to the popular TS7800 Series devices, except that they are specified for only half the output current. Like the TS7800 devices, the TS78M00A Series 3-Terminal regulators are intended for local, on-card voltage regulation.Internal current limiting, thermal shutdown circuitry and safe-area compensation for the internal pass transistor combine to make these devices remarkably rugged under most operating conditions. Maximum output current with adequate heatsink is 500mAThis series is offered in 3-pin TO-220, TO-252 package.FeaturesOutput current up to 0.5A No external components required Internal thermal overload protection Internal short-circuit current limitingOutput transistor safe-area compensationOutput voltage offered in 2% toleranceOrdering InformationNote: Where xx denotes voltage option. Part No. Operating Temp. (Ambient)PackageTS78MxxACZ TO-220 TS78MxxACP -20 ~ +85o C TO-252 Standard ApplicationA common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage.XX = these two digits of the type number indicate voltage.* = Cin is required if regulator is located an appreciable distance from power supply filter.** = Co is not needed for stability; however, it does improvetransient response.Absolute Maximum RatingInput Voltage Vin * 35 V Input VoltageVin ** 40 V Power Dissipation TO-220 TO-220 TO-252 Without heatsinkPt *** Without heatsink2 15 1 WOperating Junction Temperature Range T J 0 ~ +150 o C Storage Temperature Range T STG-65 ~ +150oCNote : * TS78M05A to TS78M18A ** TS78M24ATS78M05A Electrical Characteristics(Vin=10V, Iout=350mA, 0 o C≤Tj≤125 o C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)Parameter Symbol TestConditions MinTypMaxUnitTj=25 o C 4.90 5 5.10Output voltage Vout 7.5V≤Vin≤20V,5mA≤Iout≤350mA, PD≤5W 4.80 5 5.20VLine Regulation REGline Tj=25 o C 7.5V≤Vin≤25V,Io=200mA-- 3 50 5mA≤Iout≤500mA -- 20100Load Regulation REGload Tj=25 o C5mA≤Iout≤200mA -- 10 50mVQuiescent Current Iq Iout=0, Tj=25 o C --367.5V≤Vin≤25V ----0.8 Quiescent Current Change ∆Iq5mA≤Iout≤350mA ----0.5mAOutput Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 o C -- 40 -- uVRipple Rejection Ratio RR f=120Hz, 8V≤Vin≤18V 62 80 -- dBVoltage Drop Vdrop Iout=350mA, Tj=25 o C --2--V Peak Output Current Io peak Tj=25 o C -- 0.7 -- ATemperature Coefficient of Output Voltage ∆Vout/ ∆Tj Iout=5mA, 0 o C≤Tj≤125 o C -- -0.2 --mV/o CTS78M06A Electrical Characteristics(Vin=11V, Iout=350mA, 0 o C≤Tj≤125 o C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)Parameter Symbol TestConditions MinTypMaxUnitTj=25 o C 5.88 6 6.12Output Voltage Vout 8.5V≤Vin≤21V,5mA≤Iout≤350mA, PD≤5W 5.76 6 6.24VLine Regulation REGline Tj=25 o C 8.5V≤Vin≤25V,Io=200mA-- 3 50 5mA≤Iout≤500mA -- 20 120Load Regulation REGload Tj=25 o C5mA≤Iout≤200mA -- 10 60mVQuiescent Current Iq Iout=0, Tj=25 o C --368.5V≤Vin≤25V ----0.8 Quiescent Current Change ∆Iq5mA≤Iout≤350mA ----0.5mAOutput Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 o C -- 45 -- uVRipple Rejection Ratio RR f=120Hz, 9V≤Vin≤19V 5980--dB Voltage Drop Vdrop Iout=350mA, Tj=25 o C --2--V Output Short Circuit Current Ios Tj=25 o C -- 50 -- mAPeak Output Current Io peak Tj=25 o C -- 0.7 -- ATemperature Coefficient of Output Voltage ∆Vout/ ∆Tj Iout=5mA, 0 o C≤Tj≤125 o C -- -0.2 --mV/o Cz Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately.z This specification applies only for DC power dissipation permitted by absolute maximum ratings.TS78M08A Electrical Characteristics(Vin=14V, Iout=350mA, 0 o C≤Tj≤125 o C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)Parameter Symbol TestConditions MinTypMaxUnitTj=25 o C 7.84 8 8.16Output Voltage Vout 10.5V≤Vin≤23V,5mA≤Iout≤350mA, PD≤5W 7.68 8 8.32VLine Regulation REGline Tj=25 o C 10.5V≤Vin≤25V,Io=200mA-- 6 50 5mA≤Iout≤500mA -- 25 160Load Regulation REGload Tj=25 o C5mA≤Iout≤200mA -- 10 80mVQuiescent Current Iq Iout=0, Tj=25 o C --3610.5V≤Vin≤25V ----0.8 Quiescent Current Change ∆Iq5mA≤Iout≤350mA ----0.5mAOutput Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 o C -- 52 -- uVRipple Rejection Ratio RR f=120Hz, 11V≤Vin≤21V 5680--dB Voltage Drop Vdrop Iout=350mA, Tj=25 o C --2--V Output Short Circuit Current Ios Tj=25 o C -- 50 -- mAPeak Output Current Io peak Tj=25 o C -- 0.7 -- ATemperature Coefficient of Output Voltage ∆Vout/ ∆Tj Iout=5mA, 0 o C≤Tj≤125 o C -- -0.2 --mV/o CTS78M09A Electrical Characteristics(Vin=15V, Iout=350mA, 0 o C≤Tj≤125 o C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)Parameter Symbol TestConditions MinTypMaxUnitTj=25 o COutput Voltage Vout 11.5V≤Vin≤23V,5mA≤Iout≤350mA, PD≤5WLine Regulation REGline Tj=25 o C 11.5V≤Vin≤26V,Io=200mA5mA≤Iout≤500mALoad Regulation REGload Tj=25 o C5mA≤Iout≤200mAQuiescent Current Iq Iout=0, Tj=25 o C11.5V≤Vin≤26VQuiescent Current Change ∆Iq5mA≤Iout≤350mAOutput Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 o CRipple Rejection Ratio RR f=120Hz, 12V≤Vin≤22VVoltage Drop Vdrop Iout=350mA, Tj=25 o COutput Short Circuit Current Ios Tj=25 o CPeak Output Current Io peak Tj=25 o CTemperature Coefficient ofOutput Voltage∆Vout/ ∆Tj Iout=5mA, 0 o C≤Tj≤125 o Cz Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately.TS78M10A Electrical Characteristics(Vin=16V, Iout=350mA, 0 o C≤Tj≤125 o C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)Parameter Symbol TestConditions MinTypMaxUnitTj=25 o C 9.801010.20Output Voltage Vout 12.5V≤Vin≤25V,5mA≤Iout≤350mA, PD≤5W 9.60 10 10.40VLine Regulation REGline Tj=25 o C 12.5V≤Vin≤28V,Io=200mA-- 8 50 5mA≤Iout≤500mA -- 25 200Load Regulation REGload Tj=25 o C5mA≤Iout≤200mA -- 10 100mVQuiescent Current Iq Iout=0, Tj=25 o C --3612.5V≤Vin≤28V ----0.8 Quiescent Current Change ∆Iq5mA≤Iout≤350mA ----0.5mAOutput Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 o C -- 70 -- uVRipple Rejection Ratio RR f=120Hz, 13V≤Vin≤23V 5580--dB Voltage Drop Vdrop Iout=350mA, Tj=25 o C --2--V Output Short Circuit Current Ios Tj=25 o C -- 50 -- mAPeak Output Current Io peak Tj=25 o C -- 0.7 -- ATemperature Coefficient of Output Voltage ∆Vout/ ∆Tj Iout=5mA, 0 o C≤Tj≤125 o C -- -0.3 --mV/o CTS78M12A Electrical Characteristics(Vin=19V, Iout=350mA, 0 o C≤Tj≤125 o C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)Parameter Symbol TestConditions MinTypMaxUnitTj=25 o C 11.76 12 12.24Output Voltage Vout 14.5V≤Vin≤27V,5mA≤Iout≤350mA, PD ≤5W 11.52 12 12.48VLine Regulation REGline Tj=25 o C 14.5V≤Vin≤30V,Io=200mA-- 8 50 mV 5mA≤Iout≤500mA -- 25 240Load Regulation REGload Tj=25 o C0mA≤Iout≤200mA -- 10 120Quiescent Current Iq Tj=25 o C, Iout=0 -- 3 614.5V≤Vin≤30V ----0.8 Quiescent Current Change ∆Iq5mA≤Iout≤200mA ----0.5mAOutput Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 o C -- 75 -- uVRipple Rejection Ratio RR f=120Hz, 15V≤Vin≤25V 5580--dB Voltage Drop Vdrop Iout=350mA, Tj=25 o C --2--V Output Short Circuit Current Ios Tj=25 o C -- 50 -- mAPeak Output Current Io peak Tj=25 o C -- 0.7 -- ATemperature Coefficient of Output Voltage ∆Vout/ ∆Tj Iout=5mA, 0 o C≤Tj≤125 o C -- -0.3 --mV/o Cz Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately.TS78M15A Electrical Characteristics(Vin=23V, Iout=350mA, 0 o C≤Tj≤125 o C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)Parameter Symbol TestConditions MinTypMaxUnitTj=25 o C 14.70 15 15.30Output Voltage Vout 17.5V≤Vin≤30V,5mA≤Iout≤350mA, PD ≤5W 14.40 15 15.60VLine Regulation REGline Tj=25o C17.5V≤Vin≤30V,Io=200mA-- 8 50 mV 5mA≤Iout≤500mA -- 25300Load Regulation REGload Tj=25o C 5mA≤Iout≤200mA -- 10150Quiescent Current Iq Tj=25 o C, Iout=0 -- 3 617.5V≤Vin≤30V ----0.8 Quiescent Current Change ∆Iq5mA≤Iout≤350mA ----0.5mAOutput Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 o C -- 90 -- uVRipple Rejection Ratio RR f=120Hz, 18V≤Vin≤28V 5470--dB Voltage Drop Vdrop Iout=350mA, Tj=25 o C --2--V Output Short Circuit Current Ios Tj=25 o C -- 50 -- mAPeak Output Current Io peak Tj=25 o C -- 0.7 -- ATemperature Coefficient of Output Voltage ∆Vout/ ∆Tj Iout=5mA, 0 o C≤Tj≤125 o C -- -0.3 --mV/o CTS78M18A Electrical Characteristics(Vin=27V, Iout=350mA, 0 o C≤Tj≤125 o C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)Parameter Symbol TestConditions MinTypMaxUnitTj=25 o C 17.64 18 18.36Output Voltage Vout 21V≤Vin≤33V,5mA≤Iout≤350mA, PD ≤5W 17.28 18 18.72VLine Regulation REGline Tj=25 o C 21V≤Vin≤33V,Io=200mA-- 8 50 mV 5mA≤Iout≤500mA -- 25 360Load Regulation REGload Tj=25 o C5mA≤Iout≤200mA -- 10 180Quiescent Current Iq Tj=25 o C, Iout=0 -- 3 621V≤Vin≤33V ----0.8 Quiescent Current Change ∆Iq5mA≤Iout≤350nA ----0.5mAOutput Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 o C --110--uV Ripple Rejection Ratio RR f=120Hz, 21V≤Vin≤31V 5470--dB Voltage Drop Vdrop Iout=350mA, Tj=25 o C --2--V Output Short Circuit Current Ios Tj=25 o C -- 50 -- mAPeak Output Current Io peak Tj=25 o C -- 0.7 -- ATemperature Coefficient of Output Voltage ∆Vout/ ∆Tj Iout=5mA, 0 o C≤Tj≤125 o C -- -0.5 --mV/o Cz Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately.TS78M24A Electrical Characteristics(Vin=33V, Iout=350mA, 0 o C≤Tj≤125 o C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)Parameter Symbol TestConditions MinTypMaxUnitTj=25 o C 23.52 24 24.48Output Voltage Vout 27V≤Vin≤38V,5mA≤Iout≤350mA, PD ≤5W 22.04 24 25.96VLine Regulation REGline Tj=25 o C 27V≤Vin≤38V,Io=200mA-- 10 50 mV 5mA≤Iout≤500mA -- 30 480Load Regulation REGload Tj=25 o C5mA≤Iout≤200mA -- 10 240Quiescent Current Iq Iout=0, Tj=25 o C --4727V≤Vin≤38V ----0.8 Quiescent Current Change ∆Iq5mA≤Iout≤350mA ----0.5mAOutput Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 o C --170--uV Ripple Rejection Ratio RR f=120Hz, 27V≤Vin≤37V 5070--dB Voltage Drop Vdrop Iout=350mA, Tj=25 o C --2--V Output Short Circuit Current Ios Tj=25 o C -- 50 -- mAPeak Output Current Io peak Tj=25 o C -- 0.7 -- ATemperature Coefficient of Output Voltage ∆Vout/ ∆Tj Iout=5mA, 0 o C≤Tj≤125 o C -- -0.5 --mV/o Cz Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately.z This specification applies only for DC power dissipation permitted by absolute maximum ratings.Electrical Characteristics CurveFIGURE 1 - Worst Case Power Dissipation v.s.Ambient TemperatureFIGURE 2 - Peak Output Current v.s.Dropout VoltageFIGURE 3 – Quiescent Current v.s.Input VoltageFIGURE 4 –Dropout Voltage v.s.Junction TemperatureFIGURE 5 – Quiescent Current v.s.Output CurrentFIGURE 6 – TO-252 Thermal Resistance andPd(max) v.s. P.C.B Copper LengthElectrical Characteristics CurveFIGURE 7 – Ripple Rejection v.s.FrequencyFIGURE 8 – Ripple Rejection v.s.Output Voltage。
78S40资料
LM78S40Universal Switching Regulator SubsystemGeneral DescriptionThe LM78S40is a monolithic regulator subsystem consisting of all the active building blocks necessary for switching regu-lator systems.The device consists of a temperature com-pensated voltage reference,a duty-cycle controllable oscilla-tor with an active current limit circuit,an error amplifier,high current,high voltage output switch,a power diode and an uncommitted operational amplifier.The device can drive ex-ternal NPN or PNP transistors when currents in excess of 1.5A or voltages in excess of 40V are required.The device can be used for step-down,step-up or inverting switching regulators as well as for series pass regulators.It features wide supply voltage range,low standby power dissipation,high efficiency and low drift.It is useful for any stand-alone,low part count switching system and works extremely well in battery operated systems.Featuresn Step-up,step-down or inverting switching regulators n Output adjustable from 1.25V to 40Vn Peak currents to 1.5A without external transistors n Operation from 2.5V to 40V input n Low standby current drain n 80dB line and load regulationn High gain,high current,independent op amp nPulse width modulation with no double pulsingBlock and Connection DiagramsApril 1998LM78S40Universal Switching Regulator Subsystem©1998National Semiconductor Corporation Ordering InformationPart Number NS Package Temperature Range LM78S40J/883J16A Ceramic DIP−55˚C to+125˚C LM78S40N N16E Molded DIP−40˚C to+125˚C LM78S40CN N16E Molded DIP0˚C to+70˚C2Absolute Maximum Ratings(Note1)If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications.Storage Temperature RangeCeramic DIP−65˚C to+175˚C Molded DIP−65˚C to+150˚C Operating Temperature RangeExtended(LM78S40J)−55˚C to+125˚C Industrial(LM78S40N)−40˚C to+125˚C Commercial(LM78S40CN)0˚C to+70˚C Lead TemperatureCeramic DIP(Soldering,60sec.)300˚C Molded DIP(Soldering,10sec.)265˚C Internal Power Dissipation(Note2)(Note3)16L-Ceramic DIP 1.50W 16L-Molded DIP 1.04W Input Voltage from V IN to GND40V Input Voltage from V+(Op Amp)to GND40V Common Mode Input Range(Comparator and Op Amp)−0.3to V+ Differential Input Voltage(Note4)±30V Output Short CircuitDuration(Op Amp)Continuous Current from V REF10mA Voltage from SwitchCollectors to GND40V Voltage from SwitchEmitters to GND40V Voltage from SwitchCollectors to Emitter40V Voltage from Power Diode to GND40V Reverse Power Diode Voltage40V Current through Power Switch 1.5A Current through Power Diode 1.5A ESD Susceptibility(to be determined)LM78S40Electrical Characteristics(Note5)T A=Operating temperature range,V IN=5.0V,V+(Op Amp)=5.0V,unless otherwise specified.Symbol Parameter Conditions Min Typ Max Units GENERAL CHARACTERISTICSI CC Supply Current V IN=5.0V 1.8 3.5mA(Op Amp Disconnected)V IN=40V 2.3 5.0mAI CC Supply Current V IN=5.0V 4.0mA(Op Amp Connected)V IN=40V 5.5mA REFERENCE SECTIONV REF Reference Voltage I REF=1.0mA Extend−55˚C<T A<+125˚C,Comm0<T A<+70˚C, 1.180 1.245 1.310VIndus−40˚C<T A<+85˚CV R LINE Reference Voltage V IN=3.0V to V IN=40V,0.040.2mV/V Line Regulation I REF=1.0mA,T A=25˚CV R LOAD Reference Voltage I REF=1.0mA to I REF=10mA,0.20.5mV/mA Load Regulation T A=25˚COSCILLATOR SECTIONI CHG Charging Current V IN=5.0V,T A=25˚C2050µAI CHG Charging Current V IN=40V,T A=25˚C2070µAI DISCHG Discharge Current V IN=5.0V,T A=25˚C150250µAI DISCHG Discharge Current V IN=40V,T A=25˚C150350µAV OSC Oscillator Voltage Swing V IN=5.0V,T A=25˚C0.5Vt on/t off Ratio of Charge/ 6.0µs/µs Discharge TimeCURRENT LIMIT SECTIONV CLS Current Limit SenseVoltageT A=25˚C250350mV OUTPUT SWITCH SECTIONV SAT1Output Saturation Voltage1I SW=1.0A(Figure1) 1.1 1.3VV SAT2Output Saturation Voltage2I SW=1.0A(Figure2)0.450.7VLM78S40Electrical Characteristics(Note5)(Continued)T A=Operating temperature range,V IN=5.0V,V+(Op Amp)=5.0V,unless otherwise specified.Symbol Parameter Conditions Min Typ Max Units OUTPUT SWITCH SECTIONh FE Output Transistor CurrentI C=1.0A,V CE=5.0V,T A=25˚C70GainI L Output Leakage Current V O=40V,T A=25˚C10nA POWER DIODEV FD Forward Voltage Drop I D=1.0A 1.25 1.5V I DR Diode Leakage Current V D=40V,T A=25˚C10nA COMPARATORV IO Input Offset Voltage V CM=V REF 1.515mV I IB Input Bias Current V CM=V REF35200nA I IO Input Offset Current V CM=V REF 5.075nA V CM Common Mode VoltageT A=25˚C0V IN–2V RangeV IN=3.0V to40V,T A=25˚C7096dB PSRR Power Supply RejectionRatioOPERATIONAL AMPLIFIERV IO Input Offset Voltage V CM=2.5V 4.015mV I IB Input Bias Current V CM=2.5V30200nA I IO Input Offset Current V CM=2.5V 5.075nA A VS+Voltage Gain+R L=2.0kΩto GND;25250V/mVV O=1.0V to2.5V,T A=25˚CA VS−Voltage Gain−R L=2.0kΩto V+(Op Amp)25250V/mVV O=1.0V to2.5V,T A=25˚CV CM Common Mode VoltageT A=25˚C0V CC−2V RangeCMR Common Mode Rejection V CM=0V to3.0V,T A=25˚C76100dB PSRR Power Supply RejectionV+(Op Amp)=3.0V to40V,T A=25˚C76100dB RatioI O+Output Source Current T A=25˚C75150mA I O−Output Sink Current T A=25˚C1035mA SR Slew Rate T A=25˚C0.6V/µs V OL Output Voltage LOW I L=−5.0mA,T A=25˚C 1.0V V OH Output Voltage High I L=50mA,T A=25˚C V+(Op VAmp)−3VNote1:Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.Electrical specifications do not apply when ordering the device beyond its rated operating conditions.Note2:T J Max=150˚C for the Molded DIP,and175˚C for the Ceramic DIP.Note3:Ratings apply to ambient temperature at25˚C.Above this temperature,derate the16L-Ceramic DIP at10mW/˚C,and the16L-Molded DIP at8.3mW/˚C.Note4:For supply voltages less than30V,the absolute maximum voltage is equal to the supply voltage.Note5:A military RETS specification is available on request.At the time of printing,the LM78S40RETS specification complied with the Min and Max limits in this table.The LM78S40J may also be procured as a Standard Military Drawing.4Typical Performance CharacteristicsDesign FormulasCharacteristic Step-Down Step-Up Inverting UnitsFunctional DescriptionSWITCHING FREQUENCY CONTROLThe LM78S40is a variable frequency,variable duty cycle device.The initial switching frequency is set by the timing capacitor.(Oscillator frequency is set by a single external capacitor and may be varied over a range of100Hz to 100kHz).The initial duty cycle is6:1.This switching fre-quency and duty cycle can be modified by two mechanisms—the current limit circuitry(I pk sense)and the comparator.The comparator modifies the OFF time.When the output voltage is correct,the comparator output is in the HIGH state and has no effect on the circuit operation.If the out-put voltage is too high then the comparator output goes LOW.In the LOW state the comparator inhibits the turn-on of the output stage switching transistors.As long as the comparator is LOW the system is in OFF time.As the out-put current rises the OFF time decreases.As the output current nears its maximum the OFF time approaches its minimum value.The comparator can inhibit several ON cycles,one ON cycle or any portion of an ON cycle.Once the ON cycle has begun the comparator cannot inhibit un-til the beginning of the next ON cycle.The current limit modifies the ON time.The current limit is activated when a300mV potential appears between lead 13(V CC)and lead14(I pk).This potential is intended to re-sult when designed for peak current flows through R SC. When the peak current is reached the current limit is turned on.The current limit circuitry provides for a quick end to ON time and the immediate start of OFF time. Generally the oscillator is free running but the current limit action tends to reset the timing cycle.Increasing load results in more current limited ON time and less OFF time.The switching frequency increases with load current.USING THE INTERNAL REFERENCE,DIODE,AND SWITCHThe internal1.245V reference(pin8)must be bypassed, with0.1µF directly to the ground pin(pin11)of the LM78S40,to assure its stability.V FD is the forward voltage drop across the internal power diode.It is listed on the data sheet as1.25V typical,1.5V maximum.If an external diode is used,then its own for-ward voltage drop must be used for V FD.V SAT is the voltage across the switch element(output tran-sistors Q1and Q2)when the switch is closed or ON.This is listed on the data sheet as Output Saturation Voltage.“Output saturation voltage1”is defined as the switching element voltage for Q2and Q1in the Darlington configu-ration with collectors tied together.This applies to Figure 1,the step down mode.“Output saturation voltage2”is the switching element volt-age for Q1only when used as a transistor switch.This ap-plies to Figure2,the step up mode.For the inverting mode,Figure3,the saturation voltage of the external transistor should be used for V SAT.Typical ApplicationsCharacteristic Condition TypicalValue Output Voltage I O=200mA10V Line Regulation20V≤V I≤30V 1.5mV Load Regulation 5.0mA≤I O 3.0mVI O≤300mAMax Output Current V O=9.5V500mA Output Ripple I O=200mA50mV Efficiency I O=200mA74% Standby Current I O=200mA 2.8mA Note7:For I O≥200mA use external diode to limit on-chip power dissipation.DS010057-3 FIGURE1.Typical Step-Down Regulator andOperational Performance(T A=25˚C)6Typical Applications(Continued)Characteristic Condition TypicalValue Output Voltage I O=50mA25V Line Regulation 5.0V≤V I≤15V 4.0mV Load Regulation 5.0mA≤I O 2.0mVI O≤100mAMax Output Current V O=23.75V160mA Output Ripple I O=50mA30mV Efficiency I O=50mA79% Standby Current I O=50mA 2.6mACharacteristic Condition TypicalValue Output Voltage I O=100mA−15V Line Regulation8.0V≤V I≤18V 5.0mV Load Regulation 5.0mA≤I O 3.0mVI O≤150mAMax Output Current V O=14.25V160mA Output Ripple I O=100mA20mV Efficiency I O=100mA70% Standby Current I O=100mA 2.3mADS010057-4FIGURE2.Typical Step-Up Regulator and Operational Performance(T A=25˚C)DS010057-5FIGURE3.Typical Inverting Regulator andOperational Performance(T A=25˚C)Typical Applications(Continued)8Physical Dimensions inches(millimeters)unless otherwise noted16-Lead Molded Dual-In-Line Package(N)Order Number LM78S40N or LM78S40CNNS Package Number N16ALIFE SUPPORT POLICYNATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE-VICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI-CONDUCTOR CORPORATION.As used herein:1.Life support devices or systems are devices or sys-tems which,(a)are intended for surgical implant intothe body,or (b)support or sustain life,and whose fail-ure to perform when properly used in accordancewith instructions for use provided in the labeling,can be reasonably expected to result in a significant injury to the user.2.A critical component in any component of a life support device or system whose failure to perform can be rea-sonably expected to cause the failure of the life support device or system,or to affect its safety or effectiveness.National Semiconductor Corporation AmericasTel:1-800-272-9959Fax:1-800-737-7018Email:support@National Semiconductor EuropeFax:+49(0)180-5308586Email:europe.support@Deutsch Tel:+49(0)180-5308585English Tel:+49(0)180-5327832Français Tel:+49(0)180-5329358Italiano Tel:+49(0)180-5341680National Semiconductor Asia Pacific Customer Response Group Tel:65-2544466Fax:65-2504466Email:sea.support@National Semiconductor Japan Ltd.Tel:81-3-5620-6175Fax:81-3-5620-6179L M 78S 40U n i v e r s a l S w i t c h i n g R e g u l a t o r S u b s y s t e mNational does not assume any responsibility for use of any circuitry described,no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.。
r980t-manual-chinese说明书
1. Connecting the speakers1. Conexión de los parlantesConecte el parlante activo y el pasivo con el cable de conexión proporcionado. A continuación, conecte los cables de colores a las1. Lautsprecher anschließenVerbinden Sie die aktiven und passiven Lautsprecher mit dem mitgelieferten Lautsprecherkabel. Bitte verbinden Sie das farbigmarkierte Kabel mit der rechten Kabelklemme (das red Kabel mit der roten Klemme und das schwarz mit der schwarzen1. Connessione degli altoparlantiCollegare l'altoparlante attivo e quello passivo con il cavo di connessione incluso (cavo resso al morsetto cavo rosso e cavo14Español1. Bass-Einstellung2. Master Lautstärkeregler3. Line-in-Eingang4. EIN/AUS Schalter5. Netzanschlußkabel6. Kabelklemme1. Bassi2. Controllo volume master3. Segnale ingresso4. Interruttore dell'alimentazione5. Cavo di alimentazione6. Morsetto del cavo1. Bass adjustment2. Master volume control3. Line-in4. Power switch5. Power cord6. Wire clip1. Reguladore de grave2. Control de volumen maestro3. Entrada de línea4. Interruptor de encendido5. Cable de alimentación6. Abrazadera para cable2English8Français1. Trimmer de basses2. Contróle de volume principal3. Entrée ligne4. Interrupteur d'alimentation5. Cordon d’alimentation6. Attaches des câbles1. Connecter les haut-parleursConnecter les haut-parleurs actif et passif avec les câbles de connexion haut-parleur fournis ;connecter les câbles aux attaches selon leur couleur (le câble roug à l’attache rouge et le câble noir à l’attache noire).20Deutsch26Italiano R LR LR LR LR LPleasevisitourwebsiteat:,oremailEDIFIERSupportforfurtherassistanceat:****************,Please visit our website at: or email EDIFIER Support for further assistance at:*******************,Pleasevisitourwebsiteat:www.edifier.caoremailEDIFIERSupportat:******************If you prefer, you may contact us by phone, Toll Free: 1-877-EDIFIER (334-3437) in Canada,Veuillez consulter notre site Internet sur: , ou adresser un email au Support EDIFIER pour plusd’assistanceà:****************,Veuillez consulter notre site Internet sur: , ou adresser un email au SupportEDIFIERpourplusd’assistanceà:*******************,Veuillez consulter notre site Internet sur: www.edifier.ca ou adresser un email au Support EDIFIER à:******************Besuchen Sie unsere Webseite unter: , oder schreiben Sie eine E-Mail an den EDIFIER SupportfürweitereInformationenunter:****************,Besuchen Sie unsere Webseite unter: oder schreiben Sie eine E-Mail an denEDIFIERSupportfürweitereInformationenunter:*******************,Besuchen Sie unsere Webseite unter: www.edifier.ca oder schreiben Sie uns eine E-Mail an den EDIFIERSupportunter:******************Visita il nostro sito web: , o invia un e-mail al Supporto EDIFIER per ulteriore assistenza a:****************,Visita il nostro sito web: o invia un e-mail al Supporto EDIFIER per ulterioreassistenzaa:*******************,Visitailnostrositoweba:www.edifier.caoscriviun’e-mailalSupportoEDIFIERa:******************Se preferisci, puoi contattarci telefonicamente, Numero Verde: 1-877-EDIFIER (334-3437) in Canada,。
19780;中文规格书,Datasheet资料
Other standards are available from the agencies who produce them. MIL-HDBK 263A, EIA-IS-5-A, ASTM-F-150, EN 100015, and EIA-625. If you need help in obtaining these documents, please contact our customer service department.
Figure 1. Desco 19780 Surface Resistance Test Kit
Description
The Surface Resistance Test Kit is a portable, accurate, and versatile instrument designed to measure resistance point-to-point (RTT), surface to ground (RTG), and surface resistivity in accordance with ESD Association Standard ANSI/ESD S4.1 including: • Resistance measuring accuracy ± 10% (E11 & greater ±20%) • Resistance range <1.0 x 10E3 ohms to >10E12 ohms • Open circuit voltages of 10 and 100 volts ± 5% • Electrification period of 15 seconds • Electrodes (two) 5 pounds ± 2 oz with 50-70 durometer conductive pads In addition, the Meter measures ambient temperature and relative humidity. The Surface Resistance Test Kit (or its Meter) is referenced and designed to be used to make measurements in accordance with the test methods in: • Worksurfaces - ANSI/ESD S4.1 Worksurfaces Compliance Verification - ESD TR53 - Resistance Measurements
MUNF7808C17C04 AMD Socket AM2(940-pin)处理器 nVidia M
用户说明书AMD Socket AM2(940-pin)处理器nVidia MCP61\MCP68\MCP78主板商标所有的产品注册商标及公司名称皆属其公司所有产品内容若有更改，恕不另行通知V1.0 中文版 2009年7月MUNF7808C17C04常用除错卡代码表以下列出一些常见的自检代码，对一些可能出现的问题以及解决方式的列表，如果想了解更多的关于自检代码的信息，请参考本说明书后面的附录。
目录第1章配件 (1)1-1 包装内容 (1)1-2 主板介绍 (2)1-3 主板规格 (3)1-4 系统模块图 (6)第2章安装 (7)2-1 CPU安装 (7)2-2 跳线设置 (8)2-3 系统内存 (9)2-4 背部I/O接口 (10)2-5 主板内部接口介绍 (10)第3章常用BIOS设置 (14)3-1 主菜单 (14)3-2 标准CMOS设置 (15)3-3 BIOS高级属性设置 (16)3-4 芯片组高级属性设置 (18)3-5 集成的周边设备设置 (19)3-6 电源管理设置 (21)3-7 PNP/PCI配置设定 (23)3-8 系统状态侦测设置（可选） (24)3-9 Q-Tune Bios超频功能设置 (25)3-10 默认菜单 (27)3-11 超级用户/用户密码设定 (28)3-12 退出BIOS (28)第4章驱动以及应用程序 (29)第5章常见问题解答 (30)附录：磐正超磐手主板保修条例 (31)1-1包装内容内容 可选设备 A.主板 G.软驱数据线B.用户说明书 H.额外的USB2.0扩展端口连接C.CD I. 探温头D.I/O 挡板E.SATA II 数据线F.硬盘数据线A注：若您的包装内物品有任何的损坏或短缺情形，请与经销商联络。
E D H I CD1-2主板介绍●Socket AM2/AM2+Socket AM2/AM2+(940针)是AMD 高性能的Athlon AM2/AM2+处理器(AM2+处理器仅MCP78芯片支持)的接口，让用户体验到高效性能的执行能力。
Sangoma s400 s405 IP电话设备数据表条目说明书
DATASHEETEntry Level Device with Access to Powerful Phone ApplicationsDesigned to work with FreePBX and PBXact, Sangoma IP phones are so smart you can quickly and easily use them right out of the box.The Sangoma s400 / s405 is a full feature set phone with 3 SIP accounts at a competitive price point. These phones can quickly locate FreePBX / PBXact as soon as they are plugged into an Internet connection, and become automatically provisioned within seconds! – true Zero Touch Con guration. The s400 / s405 features industry standard Power-over-Ethernet (PoE), full duplex speakerphone, 5-way conference calling, high de nition (HD) voice quality and built-in Virtual Private Network (VPN) capability.Zero T ouch ProvisioningVoIP telephones can be complex to install, and manually con guring many different parameters and hundreds of extensions can take hours. When you buy and install your Sangoma IP phones, the redirection server automatically points the phone to the Sangoma FreePBX / PBXact for con guration.EndPoint Manager IncludedWhen using a Sangoma phone, EndPoint Manager software inside FreePBX / PBXact is automatically enabled. This lets your users control global settings, program their phone keys, map extensions, upload images, download new rmware, and much more.Full Integration with PhoneAppsPhoneApps are a bundle of advanced applications (or features), which install directly onto your IP Phone, converting all your complicated features into easy-to-use visual applications, which you control, directly from the phone’s display!See what makes PhoneApps so different from other IP phone vendors, visit: /phoneappsThe Difference Between the s400 & s405The s400 and s405 share all the same features and capabilities, with just one main difference:3x SIP Accounts2.7 Inch Graphical LCD withBacklightPhoneApps Support 25 Programmable Soft Keys 5-way Conferencing Full Duplex Speaker Phone EHS Support for Popular Wireless Headsetss405 Features Dual Gigabit Ethernet PortsOptional 3-year AdvancedHardware Replacement PlanCall Parking Follow MeDo Not DisturbConference RoomsCall ForwardingTime Conditions Presence QueuesQueue AgentsTransfer to VoicemailVisual Voicemail Login / Logout Call Flow ControlContactss400Dual-port 10/100 Mbps Ethernet s405Dual-port Gigabit EthernetSangoma s400/s405IP PhoneGeneral Features:3x SIP accountsCall hold, mute, DNDOne-touch speed dial, hotlineCall forward, call waiting, call transfer Redial, call return, auto answer 5-way conferencing XML Browser Direct IP callCustom ring tones / provisioningSet date time automatically or manually Dial plan per accountRTCP-XR (RFC3611), VQ-RTCPXR (RFC6035)Action URL/URI IP-PBX Features: Busy Lamp Field (BLF) Call park / pickup Music on hold VoicemailAnonymous call / rejection Message waiting indicator Intercom, paging Follow me / DND Conference rooms Time conditions Queues PresenceQueue agents Hot-desking Call owContactsVoice Codecs Features:HD voice: HD handset, HD speaker CodecsiLBC, G.722, G.711(A/μ), GSM_FR, G.723, G.729AB, G.726-32 DTMFIn-band, RFC 2833, SIP INFOFull-duplex hands-free speakerphone with AECVAD, AGC, CNG, AEC, PLC, AJB Display & Indicator:2.7” 192 x 364 pixel graphical LCD with backlightCaller ID with name, number and photoLED for call and message waiting indication Dual-color illuminated LEDs for line status information Feature Keys: 6 line keys with dual-color LED: 25 programmable features (5-pageview)5 feature keys: menu, headset, speaker, m ute, voicemail6 navigation keys4 context-sensitive “soft” keys Volume control keysIlluminated voicemail, speaker, headset andmute keysCerti cations: FCC Class B, CE Interface: Ethernets400: Dual-port 10/100 Mbps s405: Dual-port Gigabit 1x RJ9 (4P4C) handset port 1x RJ9 (4P4C) headset portPower over Ethernet (IEEE 802.3af) (PoE), class 2Electronic Hook Switch (EHS) support for w ireless headsetsManagement:Con gurationBrowser / LCD-menu / auto-provision Auto-provision via HTTP / HTTPS, FTP / TFTPAuto-provision with PnP Login / Logout (Hot-desking) Reset to factory, restart, reboot Local tracing log export, system logPhone lock for personal privacy protection Network & Security: SIP v1 (RFC2543), v2 (RFC3261) SIP server / proxy redundancy NAT Traversal STUN modeDHCP / static / PPPoE HTTP / HTTPS web serverTime and date synchronization by SNTPDNS-NAPTR/DNS- SRV (RFC 3263) IEEE802.1XTLS (Transport Layer Security) Open VPN QoS802.1p/Q tagging (VLAN) Layer 3 ToS DSCPHTTPS certi cate managerAES encryption for con guration leDigest authentication using MD5/MD5-sessLanguages: Built-inEnglish, French, German, Spanish, Portuguese, Russian, Italian, Polish, Turkish, Serbian, Chinese Simpli ed, Chinese Traditional, Slovenian, Farsi, Slovak and Czech Controlled by PBXChinese Simpli ed, Chinese Traditional, English, French, German, Italian, Polish, Portuguese, Russian, Spanish,TurkishPhysical Features: Shipping dimensions229mm (W) x 211mm (D) x 102mm (H) Shipping weight 1.27kgs (2.8lbs) Wall mountableStand with 3 adjustable angles Power consumption (PSU) 2.0~4.6WPower consumption (PoE) 2.5~5.5WOperating humidity 10~95%Operating temperature-10~50°COptional Accessories: External universal AC adapter (US, UK, EUR) AC 100~240V input DC 5V/1.2A output EHS headset adapterWall mount bracketAbout SangomaSangoma Technologies is a trusted uni ed communications leader, providing globally scalable telephony solution, such as on-premise and cloud-based (or hosted) IP-PBX phone systems, SIP Trunking service, Cloud-based PBX service, voice-over-IP (VoIP) Gateways, session border controllers (SBC) and telephony cards. Sangoma’s business telephony products are integrated into much of the world’s OEMs, Enterprises, Carriers and service provider networks providing seamless connectivity between traditional infrastructure and new technologies.Become a Sangoma PartnerProvide your customers with outstanding VoIP and Uni ed Communications quality products that deliver industry-leading value. As an Empowered by Sangoma Partner, you’ll get the help you need to grow your business and the incentives you want to make it easy to win sales. Discover more at: /partner-program © 2019 Sangoma Technologies Proprietary - Every effort has been made to ensure accuracy of this document.Due to ongoing improvements and revisions, Sangoma reserves the right to make changes without notice.100 Renfrew Drive, Suite 100, Markham ON L3R 9R6 Canada+19054741990or180********(tollfreeinN.America)*****************s405.En.20190314.R3。
维亚维技术智能光纤OLTS-85 85P设备说明书
FolletoVIAVISmartClass ™ Fiber OLTS-85/85PLa certificación de la fibra óptica nunca fue tan fácilLos dispositivos portátiles OLTS-85/85P de VIAVI son las soluciones más rápidas y sencillas del sector para la certificación de fibra de nivel 1. Estas incorporaciones a nuestra conocida familia SmartClass Fiber permite a los técnicos realizar las siguientes tareas:Con los dispositivos SmartClass Fiber, los técnicos obtienen niveles superiores de flexibilidad y rendimiento en una solución potente a la par que fácil de usar que permite a cualquier usuario convertirse al instante en un técnico experto en fibra. Reduzca a la mitad el tiempo necesario para realizar las pruebas y la certificación y proporcione a los clientes confianza en la calidad de su red con solo pulsar un botón gracias al dispositivo SmartClass Fiber OL TS-85/85P .Ayude a sus técnicos a trabajar con la fibra de forma inteligentey Integre la inspección y las pruebas de la fibra para obtener una solución eficaz y fácil de usar que promueva las prácticas recomendadas a la hora de manejar la fibra óptica. y Automatice la inspección de la fibra y las mediciones de pérdida de nivel 1 con resultados de tipo pasa/falla para evitar conjeturas subjetivas.y Guarde los resultados de las pruebas, las imágenes y la información del usuario de unidades tanto locales como remotas directamente en el dispositivo local.y Aplique las prácticas recomendadas con funciones que le conducen gradualmente a un flujo de trabajo de pruebas adecuado.Ventajasy Certifique instalaciones de red de forma más rápida, correctamente y a tiempo, a la primera. y Realice pruebas de fibra completas de nivel 1 conforme a las normas del sector. y Evite conjeturas subjetivas con resultados de análisis de tipo pasa/falla. y Optimice la eficiencia de los técnicos con control desde unidades tanto locales como remotas.Característicasy Pruebas de fibra completas de nivel 1 conforme a las normas TIA/ISO/IEC. y Versiones multimodo, monomodo y cuádruple específicas. y Inspección de terminaciones de fibra mediante análisis de aptitud automatizados de tipo pasa/falla tanto en dispositivos locales como remotos. y Almacenamiento integrado de los resultados locales y remotos en el dispositivo local. y Compatibilidad con flujos cerrados.y Activación instantánea a partir del modo de suspensión. y Almacenamiento integrado de los resultados de todas las pruebas. y Informes de certificación de fibra fáciles de generar. y Pantalla táctil a color de 3,5 pulgadas.y Gestión de los datos de las pruebas con J-Reporter. y Control del flujo de trabajo de extremo a extremo con CERTiFi. y Elaboración de informes rápidos a través del software de generación de informes FiberChekPRO. y Duración de la batería durante todo el día.y Medición de la longitudy Medición de la pérdida óptica (dos fibras y dos longitudes de onda)y Comprobación de la polaridady Inspección de las terminaciones de la fibra yGeneración de informes de certificaciónOptimización de la eficacia del flujo de trabajo con funciones para ahorrar tiempoPara lograr un rendimiento óptimo, se necesitan métodos sistemáticos y proactivos que numerosos técnicos encuentran problemáticos, confusos y que requieren tiempo. El dispositivo OLTS-85 supera estas barreras al integrar las herramientas esenciales en un sistema uniforme que es rápido, portátily sencillo.y Gracias a losmicroscopios de sonda yde cable de conexión, lostécnicos pueden ahorrarun valioso tiempo confunciones de inspecciónespecíficas tanto paralas placas de conectorescomo para los cablesde conexión. Y a no esnecesario cambiar laspuntas y se reduce a la mitad el tiempo necesario parala inspección.y El adaptador de microscopio de cable de conexión dúplex LC se desliza de un lado al otro para que se puedan inspeccionar ambos conectores LC del par dúplex.y Proporciona un control total del equipo de pruebas tanto en las terminaciones locales como en las remotas para que los usuarios puedan probar y guardar los resultados de cualquier terminación de la prueba. De esta forma, se elimina la necesidad de contar con más técnicos o de desplazarse constantemente entre las unidades de prueba local y remota.y El modo de suspensión ahorra una valiosa vida útil de la batería cuando no se usa el dispositivo. Además, la función de activación instantánea elimina los ciclos de arranque que consumen tanto tiempo y que son necesarios con otros dispositivos.Ahora es más fácil hacer las cosas correctamente a la primeraT anto si instala y certifica un nuevo cableado estructurado para su cliente como si gestiona la red existente de su propia empresa, aplicar las prácticas recomendadas es fundamental para garantizar que su infraestructura de fibra pueda estar a la altura de las exigencias de su empresa o centro de datos. Por este motivo, el dispositivo OL TS-85 cuenta con varias funciones automatizadas que permiten a los técnicos trabajar de forma más inteligente y rápida.y Cree y guarde configuraciones de pruebas con todoslos ajustes pertinentes (tipo de fibra, proveedor de cable, conectividad, método de referencia y ajustes de límites) para recuperarlas fácilmente. Ahorre tiempo y garantice unos ajustes y unos resultados coherentes.y La tecla de selección de entrada guía a los usuarios através de un proceso progresivo paso a paso que resultafácil y rápido, y que garantiza que el trabajo se realicecorrectamente a la primera.2 SmartClass Fiber OLTS-85/85P3 SmartClass Fiber OLTS-85/85PInspección de las terminaciones de la fibra con análisis de tipo pasa/fallaLos conectores contaminados son la principal causa de los problemas de las redes ópticas. Este problema ha llevado al sector y a la Comisión Electrotécnica Internacional (International Electrotechnical Commission, IEC) a publicar el estándar IEC 61300-3-35, una norma mundial que establece los criterios de aceptación para la calidad y la limpieza de las terminaciones de un conector de fibra. Esta norma se ha adoptado ampliamente y se ha incorporado a otras normas, incluidas la TIA-568.3 y la ISO/IEC 11801. Sin las herramientas adecuadas, comparar los conectores de fibra con una norma o especificación resulta difícil y requiere tiempo; sin embargo, estas dificultades se eliminan con las herramientas SmartClass Fiber. T anto si usa una norma del sector como requisitos específicos del cliente, el dispositivo OL TS-85 facilita la labor. y Pruebe y certifique la conformidad con las normas del sector sin confusiones.y Elimine la subjetividad del proceso de medición con análisis de aptitud automatizados de tipo pasa/falla. y Consiga resultados rápidamente desde dispositivos locales y remotos.y Guarde de forma instantánea resultados locales y remotos en el dispositivo local.y Integre los resultados en sus informes de certificación.Gestión de datos de pruebas completa y sencillaGestione fácilmente todos los datos de las pruebas con J-Reporter. Este software basado en PC se incluye con todos los modelos Certifier, de modo que los técnicos y los administradores de redes pueden mantener organizados los registros de los datos de las pruebas y generar informes. Además de gestionar los datos desde Certifier, J-Reporter también es compatible con otras soluciones de pruebas de VIAVI, incluidas OL TS-85 y MPOLx, así como las trazas OTDR del dispositivo MTS-2000 de VIAVI.Entre las funciones adicionales, se incluyen las siguientes: y Posibilidad de añadir el nombre y el logotipo de una empresa. y Generación de informes resumidos o detallados.y Creación de jerarquías para el mantenimiento de registros.El dispositivo OLTS-85 tiene la respuesta:¿Cuál de estos conectores cumple la especificación IEC?Integración con la gestión de flujos de trabajo basados en la nube de CERTiFiCERTiFi es una solución basada en la nube para equipos que diseñan, crean, prueban y certifican el cableado estructurado de redes empresariales. Con CERTiFi, los miembros del equipo pueden coordinarse en todas las fases del proyecto, desde la creación de requisitos de diseño y la asignación de tareas hasta la realización de pruebas y el análisis de las métricas del proyecto en tiempo real. Gestione sus proyectos con confianza y equipe a sus empleados para alcanzar el éxito con CERTiFi. Si desea obtener más información, consulte /certifi.y Gestione los proyectos con confianza en cada una de sus fases. y Coordine las especificaciones del proyecto con su equipo en un solo lugar.y Informe sobre los requisitos del trabajo de manera clara y en tiempo real.y Realice un seguimiento del estado del proyecto y analice los resultados desde cualquier lugar.y Asigne tareas directamente a los miembros del equipo. y Implemente tareas directamente en los instrumentos con la aplicación móvil CERTiFi.J-ReporterPanel de CERTiFi© 2019 VIAVI Solutions Inc.Las especificaciones y descripciones del producto descritas en este documento están sujetas a cambio, sin previo aviso.olts85-br-fop-nse-es 30179743 002 0719Contáctenos +34 91 383 9801 +1 954 688 5660Para localizar la oficina VIAVI más cercana,por favor visítenos en viavisolutions.es/contactenosviavisolutions.es.mxInformación para realizar pedidosKits (incluyen equipos de pruebas locales y remotos, maletín de transporte y cables de referencia de pruebas)Kit de pruebas de pérdida óptica de nivel 1 monomodo 2325/31Kit de pruebas de pérdida óptica de nivel 1 multimodo 2325/34Kit de pruebas de pérdida óptica de nivel 1 cuádruple2325/35Kit de pruebas de pérdida óptica de nivel 1 cuádruple con microscopios de cable de conexión2326/35Equipos de pruebas individuales (incluyen equipo de pruebas local, batería y cargador)Equipo de pruebas de pérdida óptica de monomodo 2325/11S Equipo de pruebas de pérdida óptica multimodo 2325/14S Equipo de pruebas de pérdida óptica cuádruple2325/15S Kit de pruebas de pérdida óptica cuádruple con microscopio de cable de conexión 2326/15SAccesorios recomendadosSonda de inspección digital P5000i con cuatro puntasFBP-SD101Visite /es-es para obtener más información, aprobaciones de proveedores y vídeos de productos.OL TS-85 OL TS-85P Conectores cuádruples OL TS-85P。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Universal Switching Regulator Subsystem
The mA78S40 is a switching regulator subsystem, consisting of a temperature compensated voltage reference, controlled−duty cycle oscillator with an active current limit circuit, comparator, high−current and high−voltage output switch, capable of 1.5 A and 40 V, pinned−out power diode and an uncommitted operational amplifier, which can be powered up or down independent of the IC supply. The switching output can drive external NPN or PNP transistors when voltages greater the 40 V, or currents in excess of 1.5 A, are required. Some of the features are wide−supply voltage range, low standby current, high efficiency and low drift. The mA78S40 is available in commercial (0° to + 70°C), and automotive (−40° to + 85°C) temperature ranges.
Figure 1. Simplified Block Diagram
16 1
MARKING DIAGRAM
16
PDIP−16 P SUFFIX CASE 648
UA78S40Px AWLYYWW
1
x = C or V A = Assembly Location WL = Wafer Lot YY = Year WW = Work Week
Thigh= +85° for mA78S40PV = +70° for mA78S40PC
2. For supply voltages less than 30 V the maximum differential input voltage (Error Amp and Op Amp) is equal to the supply voltage.
Plastic Package (TA = + 25°C) Derate above + 25°C (Note 1)
Storage Temperature Range Operating Temperature Range
mA78S40V mA78S40C
Symbol VCC
VCC (Op Amp) VICR VID
Iref
VDR ISW ID PD 1/RqJA Tstg TA
Value 40 40
−0.3 to VCC
± 30 Continuous
10 40 40 40 40 40 1.5 1.5
1500 14
−65 to + 150
−40 to +85 0 to +70
Unit V V V
V − mA V V V V V A A
Supply Voltage
Supply Current (Op Amp VCC, disconnected) (VCC = 5.0 V) (VCC = 40 V)
Supply Current (Op Amp VCC, connected) (VCC = 5.0 V) (VCC = 40 V)
VCC
PDIP−16
25 Units/Rail
mA78S40PV
PDIP−16
25 Units/Rail
© Semiconductor Components Industries, LLC, 2006
1
July, 2006 − Rev. 3
Publication Order Number: UA78S40/D
Input Offset Current (VCM = Vref) Common Mode Voltage Range (TA = 25°C) Power−Supply Rejection Ratio (TA = 25°C)
(3.0 ≤ VCC ≤ 40 V)
OUTPUT OPERATION AMPLIFIER
mW mW/°C
°C °C
ELECTRICAL CHARACTERISTICS (VCC = VCC (Op Amp) 5.0 V, TA = Tlow to Thigh, unless otherwise noted.)
Characteristic
Symbol
Min
Typ
Max
Unit
GENERAL
Op Noninv. 6 Amp Inv. Input 7
Reference 8
11 Ground
10
Comparator Inv. Input
9
Comparator Noninv. Input
(Top View)
ORDERING INFORMATION
Device
Package
Shipping
mA78S40PC
POWER DIODE
Forward Voltage Drop (ID = 1.0 A) Diode Leakage Current (TA = 25°C) (VDR = 40 V)
COMPARATOR
Input Offset Voltage (VCM = Vref)
Input Bias Current (VCM = Vref)
(RL = 2.0 kW to VCC (Op Amp), 1.0 V ≤ VO ≤ 2.5 V) Common Mode Voltage Range (TA = 25°C) Common Mode Rejection Ratio (TA = 25°C)
Some of the applications include use in step−up, step−down, and inverting regulators, with extremely good results obtained in battery− operated systems.
Regline
−Leabharlann 0.040.2mV/V
Reference Voltage Load Regulation (1.0 mA ≤ Iref ≤ 10 mA, TA = 25°C)
Regload
−
0.2
0.5
mV/mA
1. Tlow = −40° for mA78S40PV = 0° for mA78S40PC
Noninv. Inv.
Input
Input
9
10
Timing Gnd Capacitor VCC
11
12
13
Ipk Sense
14
Driver Switch Collector Collector
15
16
CT
Ipk
Oscillator
SQ
1.25V Reference
− Comp. +
− Op Amp +
2
UA78S40
ELECTRICAL CHARACTERISTICS (VCC = VCC (Op Amp) 5.0 V, TA = Tlow to Thigh, unless otherwise noted.)
Characteristic
Symbol
Min
Typ
Ratio of Charge/Discharge Time
CURRENT LIMIT Current−Limit Sense Voltage (TA = 25°C)
(VCC − Vlpk Sense)
OUTPUT SWITCH
Output Saturation Voltage 1 (ISW = 1.0 A, Pin 15 tied to Pin 16)
2.5
−
40
V
ICC
mA
−
1.8
3.5
−
2.3
5.0
ICC
mA
−
−
4.0
−
−
5.5
REFERENCE
Reference Voltage (Iref = 1.0 mA)
Vref
1.180
1.245
1.310
V
Reference Voltage Line Regulation (3.0 V ≤ VCC ≤ 40 V, Iref = 1.0 mA, TA = 25°C)
R 170
D1
8
Ref Output
7
6
5
4
3
2
1
Inv Noninv VCC Output Switch Diode Diode
Input Input Op Amp
Emitter Anode Cathode
(Bottom View)
NOTE: This device contains 84 active transistors.
Max
OSCILLATOR Charging Current (TA = 25°C)