340_380indbro
EPA8270D中文
方法8270 D气质联用仪测试半挥发性有机化合物技术翻译：刘金云 mail:piery2006@1.0范围及应用1.1方法 8270 用于测定多种类型的固体废弃物基体、土壤、空气取样媒介及水样制备的萃取物中的半挥发性有机化合物的浓度.直接注入样品的使用范围是有限的.以下的化合物可以通过此方法测试.合适的前置处理技术b 化合物 CAS编号a3510 35203540/3541 35503580 苊 83-32-9 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 苊嵌戊烯 208-96-8 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ乙酰苯 98-86-2 Ⅹ ND ND ND Ⅹ 2-乙酰氨基芴 53-96-3 Ⅹ ND ND ND Ⅹ 1-乙酰基-2-硫脲 591-08-2 LR ND ND ND LR 艾氏剂 309-00-2 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 氨基蒽醌 117-79-3 Ⅹ ND ND ND Ⅹ 氨基偶氮苯 60-09-3 Ⅹ ND ND ND Ⅹ 4-氨基联苯 92-67-1 Ⅹ ND ND ND Ⅹ 3-氨基-9-乙基咔唑 132-32-1 Ⅹ Ⅹ ND ND ND 敌菌灵 101-05-3 Ⅹ ND ND ND Ⅹ苯胺 62-53-3 Ⅹ Ⅹ ND Ⅹ Ⅹ茴香胺 90-04-0 Ⅹ ND ND ND Ⅹ 蒽 120-12-7 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 异黄樟 140-57-8 H S（43）ND ND ND Ⅹ 氯化联二苯树脂101612674-11-2 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 氯化联二苯树脂122111104-28-2 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 氯化联二苯树脂123211141-16-5 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 氯化联二苯树脂124253469-21-9 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 氯化联二苯树脂124812672-29-6 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 氯化联二苯树脂125411097-69-1 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 氯化联二苯树脂126011096-82-5 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 谷硫磷 86-50-0 H S（62）ND ND ND Ⅹ 氯炔草灵 101-27-9 LR ND ND ND LR联苯胺 92-87-5 CP CP CP CP CP苯甲酸 65-85-0 X X ND X X合适的前置处理技术 b 化合物 CAS编号a3510 35203540/3541 35503580 苯并蒽 56-55-3 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 苯并（b）荧蒽 205-99-2 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 苯并（k）荧蒽 207-08-9 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 苯并（g,h,i）茈 191-24-2 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 苯并（a）芘 50-32-8 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ p-苯醌 106-51-4 OE ND ND ND X苯甲醇 100-51-6 Ⅹ Ⅹ ND Ⅹ Ⅹ α-六氯化苯 319-84-6 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ β-六氯化苯 319-85-7 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ δ-六氯化苯 319-86-8 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ γ-六氯化苯（林旦）58-89-9 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 双（2-氯乙氧基）甲烷111-91-1 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 双(2-氯乙基）醚 111-44-4 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 双（2-氯异丙基）醚108-60-1 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 双（2-氯乙基己基）邻苯二甲酸酯117-81-7 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 4-溴苯基苯醚 101-55-3 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 溴苯腈 1689-84-5 Ⅹ ND ND ND Ⅹ 邻苯二甲酸丁基·苄基酯85-68-7 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 敌菌丹 2425-06-1 H S（55）ND ND ND Ⅹ克菌丹 133-06-2 H S（40）ND ND ND Ⅹ甲萘威 63-25-2 Ⅹ ND ND ND Ⅹ呋喃丹 1563-66-2 Ⅹ ND ND ND Ⅹ二硫磷 786-19-6 Ⅹ ND ND ND Ⅹ 氯丹（NOS） 57-74-9 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 毒虫威 470-90-6 Ⅹ ND ND ND Ⅹ 4-氯苯胺 106-47-8 Ⅹ ND ND ND Ⅹ 乙酯杀螨醇 510-15-6 Ⅹ ND ND ND Ⅹ 对氯邻氨基甲苯 95-79-4 Ⅹ ND ND ND Ⅹ 4-氯-3-甲苯酚 59-50-7 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 3-（氯甲苯）吡啶盐6959-48-4 Ⅹ ND ND ND Ⅹ 酸盐1-氯代萘 90-13-1 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 2-氯代萘 91-58-7 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 2-氯苯酚 95-57-8 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 4-氯-1,2-苯二胺 95-83-0 Ⅹ Ⅹ ND ND ND 4-氯-1,3-苯二胺 5131-60-2 Ⅹ Ⅹ ND ND ND 4-氯苯基苯醚 7005-72-3 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ合适的前置处理技术 b 化合物 CAS编号a3510 35203540/3541 35503580 1,2-苯并菲 218-01-9 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 香豆磷 56-72-4 Ⅹ ND ND ND Ⅹ 甲酚定 120-71-8 Ⅹ ND ND ND Ⅹ 丁烯磷 7700-17-6 Ⅹ ND ND ND Ⅹ 2-环己烯-4,6-二硝基-苯酚131-89-5 Ⅹ ND ND ND LR 4,4-DDD 72-54-8 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 4,4-DDE 72-55-9 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 4,4-DDT 50-29-3 Ⅹ Ⅹ Ⅹ Ⅹ X O-异内吸磷 298-03-3 H S（68）ND ND ND Ⅹ S-异内吸磷 126-75-0 Ⅹ ND ND ND Ⅹ 燕麦敌（顺式或反式）2303-16-4 Ⅹ ND ND ND Ⅹ 2,4-二氨基甲苯 95-80-7 D C,0E（42）ND ND ND Ⅹ 二苯并（a,j）吖啶 224-42-0 ⅩND ND NDⅩ二苯并（a,h）蒽 53-70-3 ⅩⅩⅩⅩⅩ二苯并呋喃 132-64-9 ⅩⅩNDⅩⅩ二苯并（a,e）芘 192-65-4 ND ND ND NDⅩ1，2-溴-3-氯丙烷 96-12-8 ⅩⅩND ND ND 苯二甲酸-n-二丁酯 84-74-2 ⅩⅩⅩⅩⅩ二氯萘醌 117-80-6 OE ND ND NDⅩ1,2-二氯代苯 95-50-1 ⅩⅩⅩⅩⅩ1,3-二氯代苯 541-73-1 ⅩⅩⅩⅩⅩ1,4-二氯代苯 106-46-7 ⅩⅩⅩⅩⅩ3,3-二氯联苯胺 91-94-1 ⅩⅩⅩⅩⅩ2,4-二氯苯酚 120-83-2 ⅩⅩⅩⅩⅩ2,6-二氯苯酚 87-65-0 ⅩND ND NDⅩ敌敌畏 62-73-7 ⅩND ND NDⅩ百治磷 141-66-2 ⅩND ND NDⅩ狄氏剂 60-57-1 ⅩⅩⅩⅩⅩ酞酸二乙酯 84-66-2 ⅩⅩⅩⅩⅩ乙烯雌酚 56-53-1 AW，ND ND NDⅩ0S（67）硫酸二乙酯 64-67-5 LR ND ND ND LR 乐果 60-51-5 H E，ND ND NDⅩH S（31）3，3`-二甲氨基联苯氨 119-90-4 ⅩND ND ND LR 二甲氨基偶氮苯 60-11-7 ⅩND ND ND X 7,12甲基苯并（a）蒽 57-97-6 C P（45）ND ND ND CP合适的前置处理技术b 化合物 CAS编号a351035203540/3541 35503580 3,3`-二甲基联苯胺 119-93-7 Ⅹ ND ND ND Ⅹ α,α-二甲基苯乙胺 122-09-8 ND ND ND ND Ⅹ 2,4-二甲苯酚 105-67-9 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 苯二甲酸二甲酯 131-11-3 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 1,2-二硝基苯 528-29-0 Ⅹ ND ND ND X 1,3-二硝基苯 99-65-0 Ⅹ ND ND ND Ⅹ 1,4二硝基苯 100-25-4 H E（14）ND ND ND Ⅹ 4,6-二硝基-2-甲酚 534-52-1 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 2,4-二硝基苯酚 51-28-5 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 2,4-二硝基甲苯 121-14-2 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 2,6二硝基甲苯 606-20-2 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 敌螨普 39300-45-3 CP，HS ND ND ND CP（28）二硝丁酚 88-85-7 Ⅹ ND ND ND Ⅹ 二苯胺 122-39-4 Ⅹ Ⅹ X Ⅹ Ⅹ 苯妥英 57-41-0 X ND ND ND Ⅹ 1,2-二苯肼 122-66-7 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 磷酸-n-二辛酯 117-84-0 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 乙拌磷 298-04-4 X ND ND ND Ⅹ 硫丹Ⅰ 959-98-8 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 硫丹Ⅱ 33213-65-9 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 硫酸硫丹 1031-07-8 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 异狄氏剂 72-20-8 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 异狄氏剂醛 7421-93-4 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 异狄氏剂酮 53494-70-5 Ⅹ X ND X Ⅹ 苯硫磷 2104-64-5 Ⅹ ND ND ND Ⅹ 乙硫磷 563-12-2 Ⅹ ND ND ND Ⅹ 氨基甲酸乙酯 51-79-6 D C（28）ND ND ND Ⅹ 乙基甲磺酸 62-50-0 Ⅹ ND ND ND Ⅹ 氨磺磷 52-85-7 Ⅹ ND ND ND Ⅹ 丰索磷 115-90-2 Ⅹ ND ND ND Ⅹ 倍硫磷 55-38-9 Ⅹ ND ND ND Ⅹ 氯氟灵 33245-39-5 Ⅹ ND ND ND Ⅹ荧蒽 206-44-0 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ芴 86-73-7 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 2-氟（代）联苯 321-60-8 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 2-氟（代）苯酚 367-12-4 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ合适的前置处理技术b 化合物 CAS编号a351035203540/3541 35503580 七氯化茚 76-44-8 X X X X X 七氯环氧化物 1024-57-3 X X X X X 六氯化苯 118-74-1 X X X X X 六氯丁二烯 87-68-3 X X X X X 六氯环戊二烯 77-47-4 X X X X X 六氯乙烷 67-72-1 X X X X X六氯酚 70-30-4 A W，ND ND ND CPC P（62）六氯丙烯 1888-71-7 X ND ND ND X 六甲基磷酸三酰胺 680-31-9 X ND ND ND X 对苯二酚 123-31-9 ND ND ND ND X 茚并（1，2，3-cd）芘 193-39-5 X X X X X 异艾氏剂 465-73-6 X ND ND ND X 异佛尔酮 78-59-1 X X X X X 异黄樟素 120-58-1 D C（46）ND ND ND X十氯酮 143-50-0 X ND ND ND X溴苯磷 21609-90-5 X ND ND ND X 马拉硫磷 121-75-5 HS（5）ND ND ND X 顺丁烯二酸酐 108-31-6 HE ND ND ND X 炔雌醇甲醚 72-33-3 X ND ND ND X 噻吩甲吡胺 91-80-5 X ND ND ND X 甲氧氯 72-43-5 X ND ND ND X 甲基胆蒽 56-49-5 X ND ND ND X 4,4`-亚甲基双 101-14-4 O E，O S ND ND ND LR （-2氯苯胺） （0）4,4`-亚甲基双 101-61-1 X X ND ND ND （N,N-二甲基-苯胺）甲基甲磺酸 66-27-3 X ND ND ND X 2-甲基萘 91-57-6 X X ND X X 甲基对硫磷 298-00-0 X ND ND ND X 2-甲苯酚 95-48-7 X ND ND ND X 3-甲苯酚 108-39-4 X ND ND ND X 4-甲苯酚 106-44-5 X ND ND ND X速灭磷 7786-34-7 X ND ND ND X兹克威 315-18-4 H E，H S ND ND ND X（68）灭蚁灵 2385-85-5 X ND ND ND X久效磷 6923-22-4 HE ND ND ND X合适的前置处理技术b 化合物 CAS编号a351035203540/3541 35503580 二溴磷 300-76-5 Ⅹ ND ND ND Ⅹ 萘 91-20-3 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ萘醌 130-15-4 Ⅹ ND ND ND Ⅹ1-萘胺 134-32-7 O S（44）ND ND ND Ⅹ2-萘胺 91-59-8 Ⅹ ND ND ND Ⅹ烟碱 54-11-5 D E（67）ND ND ND X 5-硝基苊 602-87-9 Ⅹ ND ND ND Ⅹ 2-硝基苯胺 88-74-4 Ⅹ Ⅹ ND Ⅹ Ⅹ 3-硝基苯胺 99-09-2 Ⅹ Ⅹ ND Ⅹ Ⅹ 4-硝基苯胺 100-01-6 Ⅹ Ⅹ ND Ⅹ Ⅹ 2-甲氧基-5-硝基苯胺 99-59-2 Ⅹ ND ND ND Ⅹ 硝基苯 98-95-3 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 4-硝基联苯 92-93-3 Ⅹ ND ND ND Ⅹ 除草醚 1836-75-5 Ⅹ ND ND ND Ⅹ 2-硝基苯酚 88-75-5 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 4-硝基苯酚 100-02-7 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 5-硝基-2-甲苯胺 99-55-8 Ⅹ X ND ND Ⅹ 硝基硅啉-1-氧化物 56-57-5 Ⅹ ND ND ND Ⅹ N-亚硝基二丁胺 924-16-3 X ND ND ND Ⅹ N-亚硝基二乙胺 55-18-5 X ND ND ND Ⅹ N-亚硝基二甲胺 62-75-9 Ⅹ X X X Ⅹ N-亚硝基甲基乙胺 10595-95-6 Ⅹ ND ND ND Ⅹ N-亚硝基二苯胺 86-30-6 Ⅹ X X X Ⅹ N-亚硝基二丙胺 621-64-7 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 亚硝基吗啉 59-89-2 ND ND ND ND Ⅹ N-亚硝基呱啶 100-75-4 Ⅹ ND ND ND Ⅹ 亚硝基吡咯烷 930-55-2 Ⅹ ND ND ND Ⅹ 八甲基焦磷酰胺 152-16-9 LR ND ND ND LR 4,4`-羟基二苯胺 101-80-4 Ⅹ ND ND ND Ⅹ 对硫磷 56-38-2 Ⅹ X ND ND Ⅹ五氯苯 608-93-5 X ND ND ND X 五氯硝基苯 82-68-8 Ⅹ ND ND ND Ⅹ 五氯苯酚 87-86-5 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 非那西丁 62-44-2 Ⅹ ND ND NDⅩ 菲 85-01-8 Ⅹ Ⅹ X X X 菲巴比妥 50-06-6 Ⅹ ND ND ND Ⅹ 苯酚 108-95-2 D C（28）Ⅹ Ⅹ Ⅹ Ⅹ合适的前置处理技术b 化合物 CAS编号a3510 35203540/3541 35503580 1,4-苯二胺 106-50-3 Ⅹ ND ND ND Ⅹ 甲拌磷 298-02-2 Ⅹ Ⅹ Ⅹ Ⅹ Ⅹ 伏杀硫磷 2310-17-0 HS（65）ND ND ND Ⅹ 亚胺硫磷 732-11-6 HS（15）ND ND ND Ⅹ 磷胺 13171-21-6 H E（63）ND ND ND Ⅹ酞酐 85-44-9 C P,H E(1)ND ND ND CP 2-皮考啉（2-甲基吡啶）109-06-8 Ⅹ X ND ND ND 胡椒基亚砜 120-62-7 Ⅹ ND ND ND Ⅹ 拿草特 23950-58-5 Ⅹ ND ND ND Ⅹ 丙硫氧密啶 51-52-5 LR ND ND ND LR 芘 129-00-0 Ⅹ X X X Ⅹ 间苯二酚 108-46-3 DC,OE ND ND ND Ⅹ（10）Ⅹ 黄樟素 94-59-7 Ⅹ ND ND ND Ⅹ 番木鳖碱 57-24-9 AW,0S ND ND ND Ⅹ（55）菜草特 95-06-7 Ⅹ ND ND ND Ⅹ叔丁磷 13071-79-9 Ⅹ ND ND ND Ⅹ 1,2,4,5-四氯苯 95-94-3 X ND ND ND Ⅹ 2,3,4,6-四氯苯酚 58-90-2 X ND ND ND Ⅹ 杀虫畏 961-11-5 Ⅹ ND ND ND Ⅹ 四乙基二硫代焦磷酸3689-24-5 Ⅹ X ND ND ND 焦磷酸四乙酸酯 107-49-3 Ⅹ ND ND ND Ⅹ 硫磷嗪 297-97-2 Ⅹ ND ND ND Ⅹ 苯硫酚（硫酚） 108-98-5 X ND ND ND Ⅹ 甲苯二异氰酸酯 584-84-9 HE（6）ND ND ND Ⅹ 邻甲苯胺 95-53-4 Ⅹ ND ND ND Ⅹ毒杀芬 8001-35-2 X X X X X 1,2,3-三氯苯 120-82-1 Ⅹ X X X Ⅹ 2,4,5-三氯苯酚 95-95-4 Ⅹ X ND X Ⅹ 2,4,6-三氯苯酚 88-06-2 X X X X X 氟乐灵 1582-09-8 Ⅹ ND ND ND Ⅹ 2,4,5-三甲基苯胺 137-17-7 Ⅹ ND ND ND Ⅹ 磷酸三甲酯 512-56-1 H E（60）ND ND NDⅩ 1,3,5-三硝基苯 99-35-4 Ⅹ ND ND ND X 磷酸三（2,3-二溴丙基酯）126-72-7 Ⅹ ND ND ND LR合适的前置处理技术b 化合物 CAS编号a351035203540/3541 35503580 磷酸邻三甲苯酯 78-32-0 Ⅹ ND ND ND Ⅹ O,O,O-三乙基代磷酸酯126-68-1 Ⅹ ND ND ND Ⅹ a: CAS-化学文摘服务处.b: 其它可以接受的前置处理方法参见第1.2节.分析物目录要点:AW=在萃取和储存时,吸附到玻璃器皿内壁上.CP=不可重复的色谱性能DC=不理想的分布系数(括号中的数字为回收率百分数)HE=萃取时的水解作用在酸性或碱性条件的催化下加快(括号中的数字为回收率百分数).HS=储存时的水解作用(括号中的数字为稳定性百分率)LR=较低的回应ND=没有测试到OE=萃取时,在碱性条件的催化作用下氧化作用加快(括号中的数字为回收率百分数).OS=储存时被氧化(括号中的数字为稳定性百分率).X=通过此种技术回收率大于70%.1.2除了在以上的分析物目录中列出的样品制备方法外,方法3535描述的是一个固相萃取程序,可应用于从TCLP浸出液中(表16与表17中包含性能数据)提取半挥发性物质.方法3542描述的是气体中的半挥发性有机化合物的样品制备程序,气体是通过方法0010(表11中含有代用物的性能数据)取样的.方法3545描述的是利用溶剂从固体中自动萃取半挥发性物质的装置(表12包含有性能数据).方法3561描述的是从固体中萃取多环芳香烃类(PAHs)的超临界流体装置(见表格13,14,15中的性能数据). 1.3对于能溶解于二氯甲烷的中性、酸性和碱性有机化合物，且它们能够被洗脱，无需衍生化便可从气相色谱熔融二氧化硅毛细管柱(柱上涂有少量的极性硅酮)显现尖锐的峰，大多数这样的有机化合物可用方法8270来定量测试.这些化合物包括：多环芳香烃类(PAHs)、氯化烃类、农药、邻苯二甲酸酯类、有机磷酸酯类、亚硝胺类、卤代醚类、醛类、醚类、酮类、苯胺类、吡啶类、喹啉类、芳香族硝基化合物、酚类(包括硝基酚类)。
ATE Corporation AS-05 Antenna Set 30 MHz to 18 GHz
Main Features•30 MHz to 18 GHz frequency range •Excellent Antenna Factor•Tripod adapter for easy vertical-horizontal polarization change •Individual calibration•Robust, rustproof aluminium construction •LightweightAS-05 is a compact size broadband Antenna System composed of a BC-01 Biconical Dipole, LP-04 Log Periodic Dipole Array and DR-01 Double Ridged horn Antenna designed for radiated emissions and immunity testing. It can be used in conjunction with any receiver or spectrum analyzer.Its ideal companion is the EMI Receiver Unit 9060 and 9180 that can be easily mounted on the antenna mast (*).(*)The direct connection between antenna and PMM Receiver Unit eliminates additional sources of uncertainties due to coaxial cable attenuation and scattering. For further information please consult our brochure “Fully CISPR-Compliant Digital EMC/EMI receivers 10 Hz to 18 GHz”.Antenna Set 30 MHz to 18 GHzProvided by: (800)404-ATECAdvanced Test Equipment Rentals®Ordering Information:AS-05 antenna set 30 MHz to 18 GHz with individual calibration reports.AS-05/TC antenna set 30 MHz to 18 GHz with typical calibration reports.Includes: BC-01 biconical antenna; LP-04 Log-periodic antenna; DR-01Double-rideged antenna; TR-01 wooden tripod; RF cable, 6 GHz, N(m)-N(m), 5 m; Soft carrying case; Rigid carrying case (for DR-01), Operating manual; Calibration reports*.* Individual calibration reports are provided with AS-05.AS-05/TC does not include individual calibration but typical antenna factor.Optional accessories:Additional TR-01 Wooden tripod extensible 60 - 180 cm with antenna mounting adapter for fast horizontal to vertical polaritazion changing. Additional RF cable, 3 GHz, N(m)-N(m), 5 m.Sales Office:Via Leonardo da Vinci, 21/2320090 Segrate (Milano) - ITALY Phone: +39 02 2699871Fax: +39 02 26998700Headquarter:Via Benessea, 29/B17035 Cisano sul Neva (SV) - ITALY Phone: +39 0182 58641Fax: +39 0182 586400E-Mail:**************************Internet: www.narda-sts.itRelated ProductsReceiversAntennasCalibrations service• 7010/00: EMI receiver 150 kHz to 1 GHz • 7010/01: EMI receiver 9 kHz to 1 GHz • 7010/03: EMI receiver 9 kHz to 3 GHz • 9010: EMI receiver 10 Hz to 30 MHz • 9010F: EMI receiver 10 Hz to 30 MHz• 9010/03P: EMI receiver 10 Hz to 300 MHz • 9010/30P: EMI receiver 10 Hz to 3 GHz • 9010/60P: EMI receiver 10 Hz to 6 GHz • 9030: EMI Receiver 30 MHz to 3 GHz • 9060: EMI Receiver 30 MHz to 6 GHz •FR-4003: Field Receiver 9 kHz to 30 MHz• LP-02: Log Periodic Antenna 200 MHz to 3 GHz • LP-03: Log Periodic Antenna 800 MHz to 6 GHz • TR-01: Antenna Tripod• VDH-01: Van der Hoofden test-head 20 kHz to 10 MHz • Antenna Set AS-02 (BC01+LP02+TR01)• Antenna Set AS-03 (BC01+LP02+LP03+TR01) • Antenna Set AS-04 (BC01+LP04+TR01)• RA01: Rod Antenna 9 kHz to 30 MHz• RA01-HV: Rod Antenna 150 kHz to 30 MHz •RA01-MIL: Rod Antenna 9 kHz to 30 MHz• Ansi 63,5 Antenna Factor • SAE ARP 958-D• Free-Space Antenna FactorSPECIFICATIONSFrequency range GainAntenna factor Max input power Connector Dimensions (L x H x W)Weight Colour Impedance ConstructionBC-0130 to 200 MHz -15 +2 dBi typical 8 to 14 dB/m typical 100 W N-female 65 x 65 x 137 cm1,8 kg RAL 703550 Ω nominal AluminiumA S 05-F E N -60801 - S p e c i fi c a t i o n s s u b j e c t t o c h a n g e s w i t h o u t p r i o r n o t i c eAS-05Antenna set 30 MHz to 18 GHzLP-04200 MHz to 6 GHz 6 dBi typical 12 to 40 dB/m typical100 W N-female 78 x 10 x 75 cm 1,1 kg RAL 703550 Ω nominal AluminiumDR-016 to 18 GHz 9 to 16 dBi typical 36 to 41 dB/m typical 150 W N-female 55 x 44 x 177 mm 0,25 kg RAL 703550 Ω nominal AluminiumBC-01 - Antenna Factor 106141822A F (d B /m )3090150210MHz MHz MHz MHz LP-04 - Antenna Factor 155253545A F (d B /m )1356GHzGHz GHz GHz DR-01 - Antenna Factor3634384042A F (d B /m )6101418GHzGHz GHz GHz。
TF卡座规格大全
4/31!4/31!5/563/512/311/:61/222/1126/11MSPN09A REV.SHEET SCALE .X°± 2°X.°± 5°.XX°± 1°.XXX°± 0.5°.XXX± 0.10.XX± 0.20.X± 0.30X.± 0.40PROJ.UNIT APPROVAL CHECKED TITLE DRAWN DWG NO.B C D E F G H I I H G F ED AC B Proconn Technology Co., Ltd.J J PART NO.mmGENERAL TOLERANCE CUSTOMER DRAWING PROCESS COMPLIANT Pb -01-D GND WITHOUT CARD CARD INSERTED (#10)(#9) PATENTS PENDING. ARE COVERED BY PATENTS AND/OR 2.ALL RIGHTS RESERVED,PRODUCTS )TE!DBSE!DJSDVU!;(#9(#10)GND C/D 1.THIS PRODUCT DOESN'T CONTAIN ENVIRONMENTAL HAZARDOUS MATERIALS PER DIRECTIVE 2002/95/EC FOR RoHS.C/D Micro SD Normal push-push Type Connector 4:1D /21MSPN09-X0-0000D M B Dbse!Tmpu .B.1/96!2/21!2/:11/7122/261/211/16.1/16,B!!)23!;!2* A -- CONTACT UNLEAD PLATING: A:GOLD FLASH C:10ȝ" GOLD NOTES : 1. MATERIAL : INSULATOR : HIGH TEMPERATURE THERMOPLASTIC FLAMMABILITY RARING : UL94V-0 COLOR : BLACK CONTACT : COPPER ALLOYS COVER : COPPER ALLOYS 2. CONTACT AREA PLATING : GOLD OVER Ni C/D : MICRO SD CARD CARD DETECT INDICATION 3. P/N : MSPN09- X0-0000T A 1/4B C D D EN030807 BOB :/61:/:1y3!2/21!9/111/911/41QSPDPOO YYYYYYYEBUF!DPEFQSPDPOO!MPHP!!!!DBSE DFOUFS!MJOF 25/81.X°± 2°X.°± 5°.XX°± 1°.XXX°± 0.5°.XXX± 0.10.XX± 0.20.X± 0.30X.± 0.40UNIT APPROVAL CHECKED TITLE DRAWN Proconn Technology Co., Ltd.PART NO.GENERAL TOLERANCECUSTOMER DRAWING Micro SD Normal push-push MSPN09-X0-0000YYYYYYY YYYYYYYNOTES :1.Material :Housing/Slide : High temperature thermoplastic,UL94-V0. Housing Color : Black/Slide Color11.10 0.05NOTES :1.Material :Housing/Slide : High temperature thermoplastic,UL94-V0. Housing Color : Black/Slide Color11.10 0.05OPUFT!;!2/!NBUFSJBM!;!!!!!JOTVMBUPS!;!IJHI!UFNQFSBUVSF!UIFSNPQMBTUJD!!!!GMBNNBCJMJUZ!SBSJOH!;!VM:5W.1!DPMPS!;!CMBDLProconn Technology Co., Ltd.MICRO SD REV. PUSH-PUSH TYPE (H=1.8mm)DWG NO.MSPR09-15-BMICRO SD REV. PUSH-PUSH TYPE (H=1.8mm).X°± 2°X.°± 5°.XX°± 1°.XXX°± 0.5°TITLE Proconn Technology Co., Ltd.PART NO.GENERAL TOLERANCECUSTOMER DRAWING2/96²1/2²1/21/4²1/23/21.THIS PRODUCT DOESN'T CONTAIN ENVIRONMENTAL HAZARDOUSmm .nd hold on the products sur fa ce DWG NO.Proconn Technology Co., Ltd.1.THI S PRODUCT DOE S N'T CONT A M S PN10-09-0-4000D Push Nor ma l Type(H=1.50mm ).X °± 2°X .°± 5°.XX °± 1°.XXX °± 0.5°TITLEProconn Technology Co., Ltd.PART NO.L TOLER A NCETOMER DR A WING1.THI S PRODUCT DOE S N'T CONT A M SInput M a teri a l Direction1.THI S PRODUCT DOE S N'T CONT Arton P a per Connector Other bel P a perReel P S rrier T a pe P Sˠ˦˛ˡ˃ˋˀ˔˃ˀ˃˃˄ˆˠ˦˛ˡ˃ˋˀ˔˃ˀ˃˃˄ˆˠ˦˛ˡ˃ˋˀ˔˃ˀ˃˃˄ˆ。
Rink Amide Resin_0_13653-84-4_Apexbio
For obtaining a higher solubility , please warm the tube at 37°C and shake it in the ultrasonic bath for a while.Stock solution can be stored below -20°C for several months. Evaluation sample solution : ship with blue ice All other available size: ship with RT , or blue ice upon request
产品说明书
化学性质
产品名: Cas No.: 分子量: 分子式:
Rink Amide Resin 13653-84-4 318.32 C20H14O4
CY8CMBR3XXX_CapSense Design Guide(Chinese)
耐水性 .................................................................................................................................................................. 19
® ®
CY8CMBR3xxx CapSense 设计指南
®
文 档编号： 001-91599 版本**
2
目录
1.
简介 ................................................................................................................................................................................. 6 1.1 1.2 1.3 1.4 1.5 1.6 摘要 ....................................................................................................................................................................... 6 简介 ....................................................................................................................................................................... 6 CY8CMBR3xxx 系列特性概述 ............................................................................................................................... 7 CY8CMBR3xxx 系列的特性比较 ............................................................................................................................ 9 CY8CMBR3xxx CapSense 的系统概述 ............................................................................................................... 10 CapSense 设计流程............................................................................................................................................. 11
Foobon实验耗材目录-虎斑
名称
10mL尖底离心管 15mL尖底离心管 15mL尖底离心管
包装
50支/包, 12包/箱 100支/盒, 10盒/箱 50支/包, 12包/箱
详细信息可访问官网:
全国客服统一热线: 400-993-2293
4
Foobon 虎 斑 实 验 耗 材 — 移 液 吸 头
P15-P16 洗瓶/容器系列
Bottles Series
P17-P20 细胞培养专用系列
Cell Culture Consumable Series
离心管系列
Centrifuge Tube Series
货号 Order No.
FB11-005 FB11-005X FB11-015 FB11-015X FB11-020 FB11-020X FB11-050 FB11-050X FB11-070 FB11-100 FB11-100G
产品图片 Pro.Image
Foobon
离心管对比
Comparison of similar products
Foobon 1.5mL尖底透明离心管与普通款对比
普通款管壁薄，使用回料制作，管壁与管口连结不够紧密；
普通款
1、Foobon 1.5mL离心管采用新料制作，重量比普通款更重，管壁厚实， 承受更高的转速，盖子与管口配合较好, 松紧恰到好处； 2、内壁光滑，保证最大程度样品回收； 3、适合所有标准转子；耐受温度范围为：-80℃+121℃； 4、可在121℃/15psi灭菌15分钟；
5mL圆底透明离心管 5mL Snaplock Microcentrifuge Tubes, PP, Clear, Round Bottom, Nonsterile
HT-69020NP-0, HT-69030NP-0 Duct Probe RH Transmitt
HT-69020NP-0, HT-69030NP-0 Duct Probe RHTransmitter Installation GuideIntroductionThe HT-69 Series Duct Probe Relative Humidity (RH)Transmitters use a highly accurate and reliable thermosetpolymer-based capacitance humidity sensor and state-of-the-art digital linearization and temperature-compensated circuitry to monitor humidity levels in a duct. The humidity sensor is encapsulated in a 60 micron HDPE filter at the end of a 9 in. (230 mm) stainless steel (S/S) probe and a compact enclosure.Figure 1: HT-69 Duct Probe RH Transmitter DimensionsFigure 2: Dimensions of the HT-69 Duct Probe RH Transmitter*241102556A*Part No. 24-11025-56 Rev. A2022-11-11MountingThe transmitter installs directly into any air duct with a minimum width or diameter of 10 in. (25.5 cm).-Select a suitable installation area in the middle of the duct wall.-To achieve the best reading, do not place in an area where air stratification may be present.-Mount the sensor at least 5 ft. (1.5 m) in either direction from elbows, dampers, filters, or other duct restrictions.-Avoid areas that expose the transmitter to vibrations or rapid temperature changes.To install the transmitter, complete the following steps:1.When you select a suitable spot, drill a 0.6 in. (15mm) to 0.75 in. (20 mm) hole for the probe.2.Slide the probe into the drilled hole until the enclosure is flush against the duct. The airflow direction is not important.3.Secure the enclosure to the duct with two No. 10 x 1 in. (25 mm) self-tapping screws (not provided).4.Tighten the screws until the enclosure is tight against the duct so that there is no movement of the enclosure. A foam gasket on the back of the enclosure provides a tight seal against any air leaks. See Step 1 in Figure 3.5.The enclosure includes a hinged cover with a latch.To open the cover, pull slightly on the latch on the right side of the enclosure. At the same time, pull on the cover as shown in Step 2 of Figure 3.6.A 0.5 in. NPT threaded connection hole is in the bottom of the enclosure. Screw the EMT or cable gland connector into the threaded connection holeuntil tight. See Step 3 in Figure 3.Note: Preferably use weatherproof EMT or cable gland fittings. The E-style enclosure includes 0.5 in. NPT to M16 thread adaptor and cable gland fitting.7.Make wire connections as shown in the wire diagram in Wiring .8.Swing the door closed until it securely latches. For added security, install the two provided screws in the integrated screw tabs. See Step 4 of Figure 3.Wiring•Deactivate the 24 VAC/DC power supply before you make all connections to the device to prevent electrical shock or equipment damage.•Use 14 AWG to 22 AWG shielded wiring for allconnections and do not locate the device wires in the same conduit with wiring that supplies inductive loads such as motors. Make all connections in accordance with national and local codes.•Pull at least 6 in. (15 cm) of wire into the enclosure,then complete the wiring connection according to the wire diagram for the applicable power supply and output signal type. See Figure 4.•Place the output switch in the required position to select the required signal output type (mA or VDC), as shown in Step 2 of Figure 4. The factory default setting is 4 mA to 20 mA.•If you select mA, no further output set up is required.If you select VOLT output as shown in Figure 5, place the voltage output switch to the required span position,that is 10 VDC = 0 VDC to 10 VDC. The factory default setting is 0 VDC to 10 VDC. See Step 1 of Figure 4.•Connect the DC positive or the AC voltage hot side to the PWR terminal. For voltage output or AC power,connect the supply common to the COM terminal.The device is reverse voltage-protected and does not operate if you connect it backwards. The device contains a half-wave power supply so the supplycommon is the same as the signal common. See Step 3of Figure 4.•The analog output is available on the OUT terminal.Check the controller Analog Input to determine the correct connection before you apply power as shown in Step 3 of Figure 4.Figure 3: Mounting the HT-69 Duct Probe RH TransmitterFigure 4: Wiring of the HT-60 Duct Probe TransmitterTechnical specificationsTable 1: HT-69020NP-0, HT-69030NP-0 Duct Probe RH Transmitter technical specificationsThe performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson Controls shall not be liable for damages resulting from misapplication or misuse of its products.Product warrantyThis product is covered by a limited warranty, details of which can be found at / buildingswarranty.Software termsUse of the software that is in (or constitutes) this product, or access to the cloud, or hosted services applicable to this product, if any, is subject to applicable end-user license, open-source software information, and other terms set forth at /techterms. Your use of this product constitutes an agreement to such terms. PatentsPatents: https://Single point of contactContact informationContact your local branch office: /locationsContact Johnson Controls: /contact-us© 2022 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision and。
ActinBlue 350染色试剂说明书
ActinBlue™350stain——细胞骨架微丝蓝色荧光探针产品货号包装规格C051T40unitC051300unit储存条件：-20℃，避光保存。
激发/发射波长：347/440nm产品说明书GeneCopoeia,Inc.广州易锦生物技术有限公司广州高新技术产业开发区广州科学城掬泉路3号广州国际企业孵化器F区8楼邮编：510663电话：4006-020-200邮箱：******************网址： ©2015GeneCopoeia,Inc.ActinBlue™350Stain产品货号C051T/C051产品介绍ActinBlue™350Stain是一种采用蓝色荧光探针Andy Fluor™350标记的鬼笔环肽，可以对F-肌动蛋白特异性染色，可用于对甲醛固定和打孔的组织切片、细胞培养物或无细胞实验体系中的F-肌动蛋白进行标记、鉴别和定量。
ActinBlue™350Stain比抗体染色更优越，适用于经过固定和通透的样品。
荧光标记的鬼笔环肽与肌动蛋白对于不同的物种，包括植物和动物具有几乎相同的高结合属性。
鬼笔环肽与F-肌动蛋白结合具有高选择性，呈现很少的非特异性染色。
本产品可以用于荧光显微镜、微孔板、比色皿和流式细胞仪。
产品特点：●与F-肌动蛋白具有高度亲和性。
●荧光信号稳定性好。
●染色效果优于抗体染色。
注意事项对于微量的液体，每次使用前先离心数秒钟，使液体充分沉降到管底。
荧光染料均存在淬灭问题，请尽量注意避光，以减缓荧光淬灭。
为了您的安全和健康，请穿实验服并戴一次性手套操作。
染色液配制方法使用200µl甲醇溶解40单位的ActinBlue™350stain(C051T)或者使用1.5ml甲醇溶解300单位的ActinBlue™350stain(C051)制成200单位/ml的染色储存液。
每一单位的定义是染色一份显微镜载物片或固定细胞所需的溶液，相当于大约5µl的荧光素鬼笔环肽溶液。
美国推出网印油墨的低固化添加剂
国际涂料公司总裁 Ｓ ｅ ｅ ａ ａ ｅ ．３ ０ ｔＰ ｎ 说 ｈ Ｋ ｈｎ ８４ 苯二 甲酸 （ ） 固化添 加剂为 当前市 场上 日益扩 Ｐ 低 Ｆ 大的热敏感基板提供 了新 的印花机遇。几 家大型印
刷 厂 的 Ｂ ｔ 实验 结 果 非 常 积 极 ，显 示 ３ ０ 苯 二 ｅａ ８４ 甲酸 （ ） 固化 添 加 剂 非 常 容 易使 用 ，效 果 令 人 Ｐ 低 Ｆ 满意。 ３ ０ 苯 二 甲酸 （ ） 固 化 添 加 剂 为 热 敏 感 基 ８４ Ｐ 低 Ｆ 板 提 供 一 个 印 刷解 决 方 案 ，当放 在传 统 烤 箱 或 者烘
料用树脂新品种 申请表 。对认为存在
定毒性 、
对人体有害的物 质 ，填报 《 建议禁止用于食 品包装 材料的物质名单》。 《 通知》指 出 卫生部会 同有关部门成立专家 组 ，对行业 、企业提交的材料进行科学评估 ，根 据
评 估 结 果 拟定 《 用于 食 品 包 装材 料 的物 质 名单 》 可 和 《 止 用于 食 品包 装 材 料 的 物 质 名单 》 ，并 分 批 禁 向社 会 公 布 。对 于 《 止 用 于食 品包 装 材 料 的 物 质 禁 名 单》 发 布 后 仍 继续 使 用 名单 中的 物 质 制 售食 品包
＿ 萼 ■＿ ；
投 诉举报 电话或 电子 邮箱 发动群 众举报 非法生
卫生部等７ 联合开展食品包装材料清理工作 部门
卫 生 部 等 ７ 门 日前 联 合 下 发 《 于 开 展 食 部 关 品 包 装 材 料 清 理 工 作 的通 知 》 （ 下 简 称 “ 《 以 通 知》 ” ） ，要 求政 府 各 相 关 部 门 广 泛发 动各 行 业 、 企 业 ，按 照 《 品安 全 法 》 的规 定 ，对 市 场 上 存 在 食
广东环凯微生物科技有限公司-钠氏试剂-产品说明书
专注微生物监测控制为食药安全保驾护航
广东环凯微生物科技有限公司
网址： 地址：广州市黄埔区科学城神舟路788号
邮编：510663传真：************-8619销售热线：************转8602（分机）技术热线：************转8877、8876
（分机）产品说明书Product Manual
【产品名称】
通用名称：钠氏试剂
英文名称：Nessler Reagent 【产品编号与包装规格】
产品编号
产品类型包装规格029229液体10mL
【产品用途】
用于绿脓杆菌分解乙酰胺产氨试验。
【检验原理】
细菌产生一种脱酰胺酶，可使乙酰胺经脱酰胺作用释放氨，滴加钠氏试剂（碘化汞钾），氨在碱性条件下与碘化汞钾作用，生成红色络合物。
【使用方法】
滴加钠氏试剂1-2滴（约0.05-0.1mL）于培养物中，轻摇试管（西林瓶），阳性者产生红褐色沉淀，阴性者为黄色。
【质量控制】
【储存条件与保质期】
2-8℃避光保存，有效期一年。
【废物处理】
检测之后带菌物品置于121℃下高压灭菌30分钟后处理。
【执行标准】
Q/HKSJ 0704广东环凯微生物科技有限公司企业标准
【说明版本】
2019年5月14
日。
Francis Searchlights LSP380 Portable Light Weight
User Instruction & Installation ManualLSP380 PortableLightweight Suez 575wProduct Reference Number:A2273 – LSP380 115v Portable Light Weight Suez 575w A2274 – LSP380 240v Portable Light Weight Suez 575w Manufacturers details: Distributor details:Francis Searchlights LtdUnion Road, BoltonLancashire, BL2 2HJ, UKTel: +44 (0) 1204 558960Fax: +44 (0) 1204 558979E-mail:****************.ukManual Part Number: C22276Issue: 3CONTENTS1 - Introduction2 - Safety Precautions3 - Technical Information4 - Unpacking and Installation Instructions5 - Electrical Installation6 - Operating Instructions7 - Fault Finding8 - Maintenance and Servicing9 - Wiring Diagram & General Assembly10 - Spare Parts List1 - IntroductionIt is imperative that this manual is read carefully and understood before installing your equipment. For your future reference please keep this manual in a safe place.Thank you for specifying a product from the Francis Searchlights range. All Francis products are designed to give complete customer satisfaction and are manufactured to the highest engineering standards in order to ensure optimum performance and service life.The Francis LSP range combines features proven over many years service in the most hazardous conditions in both marine and land installations.In order to prolong the life and performance of your product, we recommend that you only specify Francis Searchlights spare parts. This will also ensure that any warranties on your equipment will not be invalidated. Information on spares ordering and parts is provided in this manual.Should you ever need to contact Francis Searchlights Ltd. regarding your equipment, please quote the Product Serial Number at all times.Back To Top2 - Safety PrecautionsThe following instructions must be adhered to, in order to ensure a safe working environment and the safety of the user.⏹Prevent rain, snow, condensation and water droplets from contacting the lamp as this maycause bulb failure and possible shattering;⏹Because of the high internal pressure in excess of atmospheric. Whilst the construction isinherently strong, there is a slight risk of the bulb shattering;⏹Never look directly into an illuminated searchlight as this may cause severe damage toeyesight. If it is necessary to inspect a lamp whilst in operation, always wear suitable protective goggles;⏹Should it be necessary to examine the lamp with the front bezel removed, always use aprotective shield and wear goggles to ensure a safe working environment;⏹Never attempt to clean a lamp whilst in use;⏹Searchlights get hot. Never touch the unit when lit and always allow 15 to 20 minutes forcooling down after turning the searchlight off;⏹Never place anything on or cover the searchlight when in use;⏹Ensure the lamp has cooled sufficiently before removal;⏹If undue force appears necessary to remove the lamp, the equipment should be inspected by acompetent person or contact the manufacturer;⏹When breaking a lamp for disposal, care must be taken to ensure the glass fragments aresafely contained. This operation must be performed out of doors in free air. In allcircumstances refer to the lamp manufacturers instructions packed with the lamp;⏹Due to the vast range of lamps available it may appear possible that more powerful lamps canbe used in the equipment than for which it was designed. Even when the unit will physically accept a higher wattage or voltage lamp, this substitution is not recommended and isdangerous. This action will also void any warranties on the equipment.Always refer to the lamp manufacturers technical data when dealing with lamps.Back To Top3 - Technical InformationThis product has been designed to operate in accordance with the product specification. The LSP380 searchlight has the following features:⏹Constructed from marine grade aluminium and stainless steel fixings;⏹Parabolic split glass reflector;⏹Stove enamel paint finish;⏹Vertical movement +5° to -35°;⏹Toughened front glass;⏹Integral on/off switch;⏹Enclosure protection to IP65;⏹Weight 15.8Kg which includes Searchlight and power supply;⏹Fitted with G22 lamp changeover system, in event of lamp failure;⏹Instant lamp re-strike. No cooling down time required.⏹Split beam of two 20° sections giving a credible 40° split arc;⏹Shoulder carry strap for ease of transportation;The searchlight also performs to the following optical data:Volts Watts Range P.B.C.P. Div* Lamp Life Lamp Despatch @ 1 Lux (Hours) Cap Number 110v 575w 3767M 14,190,201 2.1° 750 G22 D15764 240v 575w 3767M 14,190,201 2.1° 750 G22 D15764In order that the searchlight operates correctly it is imperative that competent personnel are responsible for the installation, operation and servicing of this equipment. Failure to adhere to this advice may cause premature failure or incorrect operation of the searchlight, which may damage the equipment or cause personal injury.Back To Top4 - Unpacking and Installation InstructionsThe following instructions should be read and fully understood prior to installing the equipment to ensure that the correct procedures are followed, and all safety precautions are observed.Note: If the equipment has been in storage for a considerable amount of time, it is advisable to conduct a routine maintenance check on all parts before installation.Safety PrecautionsThis equipment should not be connected to an electrical supply before being installed. Installation procedures should be adhered to in order to ensure a safe working environment and reduce the risk of damage or personal injury.Preparing the Mounting PositionMark out and drill the fixing holes through the deck, it may be necessary to use a suitable sealant such as silicone on any uneven surfaces, in order to ensure a weatherproofed joint.Back To TopFor safety purposes, only competent personnel should perform the electrical installation. All equipment should be installed to current Electrical Regulations and Standards.In order to obtain the maximum light output from the searchlight, it is essential that the full operating voltage of the lamp fitted be applied to the lampholder contacts.Method of Electrical Connection1) Disconnect the supply before working on the electrical system;2) The searchlight must be connected to a fused electrical supply, using suitably sized cable;3) If the searchlight is located a considerable distance from the supply, provision must be made inthe cable size in order to overcome the voltage drop. The following table should be used for indication purposes only:4) Whenever possible cable terminations should be made below deck and with approved terminaldevices;5) If a spare auxiliary fuse or circuit breaker is not available, one of the correct type and ratingshould be fitted and connected to a positive supply. It is advisable to locate a bus bar or main connection and avoid any direct connection to the supply:6) For 110/220v AC products, the following colour coding system should be used for the customersupply cable:Brown - LiveBlue - NegativeGreen/Yellow - EarthNote: This equipment must be earthed.Back To TopThis equipment is designed for use out of doors, in free air. Never place anything on, or cover, the searchlight when in use as this may present a hazard.The beam of the searchlight can be adjusted to give a 40° split, simply release the external lock wheel and adjust the lever to achieve the desired beam split required.In event of lamp failure, the changeover mechanism can be activated by rotating the lever 180°, which then switches power to the second lamp. The second lamp may take a few seconds to achieve full brightness.This product should not be used for any purpose other than for which it was designed. Any modifications to the product should not be undertaken without consulting the manufacturer. Setting to WorkSafe service in use necessitates the strict observance of the following precautions.⏹Any article fabricated from quartz or glass is inherently fragile and care shouldtherefore be taken, at all times, when handling lamps;⏹Eye protection must be worn when handling lamps that have been removed from theirpackaging materials. The protective jacket should not be removed from the lamp forsafety reasons, as there is a remote possibility of the lamp shattering violently,especially if it is subjected to mechanical shock or vibration;⏹Always isolate the equipment from the supply before inserting a lamp;⏹Before inserting the lamp ensure that all contacts are clean. Contacts must berenewed at the slightest sign of corrosion. Sanding or filing down corroded areas is notrecommended as this will only make the conducting surface between the pin andlampholder smaller, thus causing the lamp to overheat;⏹Do not twist or bend the fused quartz bulb when fitting the lamp as mechanicalstresses MUST be avoided;⏹The lamp must be capable of unimpeded expansion when it warms up to operatingtemperature. Mechanical forces must not be applied to the fused quartz bulb;⏹Before the protective jacket is removed, suitable protection must be worn i.e face maskand gloves with wrist protection;⏹Never touch the quartz bulb with bare hands, as fingerprints will make the glass cloudyand cause a severe loss of light. This may also cause recrystallisation and thusweaken the bulb material. Should the bulb be inadvertently touched, removefingerprints with methylated spirit and a clean, soft paper towel. The bulb should thenbe wiped with distilled water. NOTE: ALWAYS WEAR MASK AND GLOVES DURINGCLEANING);In all circumstances the lamp manufacturers data should be referred to when dealing with lamps.When fitting the lamp:-Always isolate the equipment from the supply when inserting a lamp;-Ensure the circuit is suitably fused;-Ensure the lamp is of the correct power rating and type;-Check lampholder is in good condition. If the contacts show any sign of corrosion, replace the lampholder;-Check the lampholder is in a good dry condition. Never allow water to collect in the lamp fitting or come into contact with the lamp.To fit the lamp:-Loosen all the latches from the front of the searchlight by pressing down the safety catch and releasing the clip, remove the bezel and glass and store in a safe place;-Cut open one end of the protective sleeve surrounding the lamp;-Using the sleeve to prevent the fingers coming into contact with the lamp, position the two pins above the holes in the lampholder;-Gently push the lamp into the lampholder and remove the protective sleeve;TestingUpon correct installation and connection to an electrical supply, the equipment can be tested in order to ensure its’ correct performance. A competent person with some knowledge of electri cal equipment must carry out this work.Equipment required: Multimeter with leadsAmmeterUsing the equation P=VI, the approximate power output of the equipment can be calculated in the following way:-Using the multimeter, take a voltage reading;-Using the ammeter, take an amp reading from the live cable to the lamp;-Multiply these figures together to give an approximate wattage (Power output).For example:Using a 240v 1000w Tungsten halogen lamp:Voltage reading = 240v; Amps reading = 4 ampsTherefore, Wattage = 240 x 4 = 960 wattsBack To Top7- Fault FindingAll fault finding must be conducted by a competent person or qualified Electrical Engineer. Failure of Lamp to lightCauses:1)Power not supplied;2)Fuse blown;3)Failed lampRemedy:1)Check voltage at supply. If supply is not present the fault is at the customer supply. If power ispresent, see remedy 2;2)Check fuse for visual failure. If none noticeable check fuse for continuity using a multimeter. Iffuse found to be faulty, replace with new part and test equipment again for correct working order. If found to be working correctly see remedy 3;3)Firstly, check supply at rear bulkhead terminal rail (within searchlight barrel). If supply ispresent, disconnect unit from power supply before removing the lamp. If the lamp envelope is discoloured, replace the lamp. Replace lamp ensuring all precautions and instructionspreviously outlined in this manual are adhered to.4)Check that the fans in the power supply box are working correctly, if not check that the supplyis present if so, replace fan.5)Check input supply to the power supply unit is correct.6)Check that the switch on the searchlight barrel is working correctly, if not check that the supplyis present if so, replace switch.Back To Top8 - Maintenance and ServicingIn order to prolong the service life and performance of your searchlight, the following maintenance guidelines are recommended:⏹Maintenance checks should be conducted before every voyage or at least every three months;⏹Before checking, disconnect the equipment from the supply;⏹Visually inspect the condition of the equipment;⏹Any major or minor structural damage should be rectified immediately in order to reducesympathetic wear;⏹After inspection it may be necessary to clean the inside of the searchlight. The followingprocedure should be adhered to:⏹Remove the front bezel;⏹Clean the front glass inside and out using a proprietary glass cleaner;⏹Clean the reflector if required;⏹Check the reflector mounting gaskets. If signs of corrosion or damage areevident, replace as necessary;⏹Ensure that the lampholder is free from corrosion or other damage;⏹Check earth point for conductivity;⏹It is advisable to check all seals and gaskets for signs of degradation. Renew if necessary;⏹Upon completing all maintenance requirements, the searchlight should be tested for fullworking order (approximately 20 minutes).If in any doubt as to the correct servicing procedures to adopt please contact your distributor/agent or the manufacturer who will be able to advise the best course of action for your product.Back To Top9 – Wiring diagram & General AssemblyDrawing Number DescriptionC22018 Wiring DiagramA2273 General Assembly10 - Spare Parts ListThe following spare parts can be ordered directly from the manufacturer:Part Number Description Part Number DescriptionC22106 PSU Assy. C11025 Lockwheel Assy.C20595 Elevation bush C20596 Elevation washerC22170 Elevation link C22103 Shoulder strapC16893 Grommet C22268 Ventilation plug assy.C22198 Lampholder Assy. C22151 Rear gasketC22041 Proximity switch C14239 Handle (Top)C09880 Switch C22051 Sealing bootC20550 Latch C22056 IgnitorC22044 Relay base C22045 Relay 115vC22046 Relay 240v C22042 Varistor 115vC22043 Varistor 240v C22061 Front glassC22011 Front glass gasket C10870 LampholderC22040 Magnet C13980 ReflectorC20827 Reflector pads C02196 Shutter springC05125 Tension spring C22104 PSU FanC22055 PSU D15764 575w LampIn order to prolong the life and performance of your product, we recommend that you only specify Francis Searchlights spare parts. This will ensure that any warranties on your equipment will not be invalidated.When ordering spare parts please contact the Sales Department at Francis Searchlights Limited. Please quote searchlight model and serial number at all times. This will enable a fast response to your spares’ requirements.Back To Top。
BL21-CodonPlus-RP Competent Cells, Part Number 230
BL21-CodonPlus-RP Competent Cells, Part Number 230250*************(24小时)化学品安全技术说明书GHS product identifier 应急咨询电话（带值班时间）::供应商/ 制造商:安捷伦科技贸易（上海）有限公司中国（上海）外高桥自由贸易试验区英伦路412号（邮编:200131)电话号码： 800-820-3278传真号码: 0086 (21) 5048 2818BL21-CodonPlus-RP Competent Cells, Part Number 230250化学品的推荐用途和限制用途BL21-CodonPlus-RP competent cells 230250-41pUC 18 DNA Control Plasmid 200231-42XL10-Gold 2-Mercaptoethanol 200314-43部件号:物质用途:分析试剂。
230250-41BL21-CodonPlus-RP competent cells1 ml（毫升） (10 x 100 µl)200231-42pUC 18 DNA ControlPlasmid0.01 ml（毫升） (0.1 ng/µl)200314-43XL10-Gold2-Mercaptoethanol0.05 ml（毫升）部件号（化学品试剂盒）:230250安全技术说明书根据 GB/ T 16483-2008 和 GB/ T 17519-2013GHS化学品标识:BL21-CodonPlus-RP 感受态细胞，部件号 230250物质或混合物的分类根据 GB13690-2009 和 GB30000-2013紧急情况概述BL21-CodonPlus-RP competent cells液体。
pUC 18 DNA Control Plasmid 液体。
Epi-ReadyPolishedAlNSubstrate-gmsystems
Polycrystalline Aluminum Nitride (AlN) SubstrateProduct Data SheetTriangle Ceramics991 Aviation Pkwy, Suite 800Morrisville, NC 27560Tel: +1 919 415 1546**************************Product OverviewTriangle Ceramics’polycrystalline aluminum nitride substrates are semiconductor process ready with shape specifications meeting SEMI specifications for wafer processing. Designed for high volume cassette-to-cassette wafer fab operations, the substrates are currently available in 150 mm and 200 mm diameters. In addition, we have the capability to manufacture 300 mm and 450 mm diameter material (contact factory).Our unique patent-pending manufacturing process enables large diameter, low cost substrates with a shape and finish ready for semiconductor processing. Typical manufacturing processes used for poly-AlN cannot consistently meet the SEMI shape and surface finish requirements for volume wafer production. Semiconductor applications that require matching thermal expansion coefficient, and require a high thermal conductivity, engineered poly-AlN wafers are a cost effective solution. Compared to sapphire substrates, the CTE match with GaN is improved by 10X. This will yield longer life and improved performance due to lower dislocation density.Standard material is double side polished (single-side and unpolished wafers are also available), and the standard thickness for 150 mm wafers is 635 +/- 15 um. Thicker or thinner wafers can also be available.ApplicationsLayer Transfer:With much of today’s research for LED’s, power conversion devices, and other devices aimed at advanced performance with improved substrates, poly-AlN offers an excellent platform for layer transfer technology where cost, device performance, and thermal management need to be critically balanced to lead the industry.Mechanical wafers: Polycrystalline AlN is well suited for mec hanical wafer applications as a lower cost substitute for sapphire, or where a thermal conductivity higher than sapphire would help improve device performance and cost. With a 200 mm and beyond wafer diameter, polycrystalline AlN can enable large diameter silicon processing where sapphire cannot go.Handle Wafers:With an electrical resistivity of over 1E14 Ohm-cm, polycrystalline AlN is also well suited as a handle wafer in SOI and SOS wafer applications, enabling CMOS and MEMS technologies to experience the cost and capacity benefits of 200 mm and beyond processing.Heat Spreaders: For device manufacturing where thermal management plays a pivotal role in device performance, poly-AlN is an ideal material for eliminating heat. With a thermal conductivity several times higher than sapphire, AlN can be used to transport thermal energy away from devices quickly.Selection of AlN Materials OfferedHP-AlN: High Purity Aluminum Nitride- this material contains no sintering aid and generally has impurities (excluding oxygen) in the PPM range. This is commonly used in semiconductor and military applications where purity is critical.HR-AlN: High Reflectivity (white) Aluminum Nitride- this material is very white, similar to alumina, and is used for optical applications where thermal conductivity needs to be much higher than alumina and material is required to be electrically insulating.ZP-AlN: Zero Porosity Aluminum Nitride- while most available AlN is considered ‘fully dense’, SEM and AFM can reveal porosity in the 2+ um range. Our Zero Porosity AlN material has almost no pores >1 um. This material is typically used for semiconductor (specifically Silicon) layer transfer applications where surface planarity, pitting, and smoothness are critical.HK-AlN: High Thermal Conductivity Aluminum Nitride- this is 180+ W/mK material typically used for thermal management.200 mm Wafer SpecificationsImage of 150 mm polished poly-AlN double side polished wafer Image of 200 mm double side polished poly-AlN wafersOptical Images of Grain StructureSEM ImageAFM Image。
balluff bni iol-709-000-k006 bni iol-710-000-k006
BNI IOL-709-000-K006 BNI IOL-710-000-K006IO-Link Sensor-Hub analogUser’s GuideContent1Notes to the user 21.1Structure of the guide 21.2Typographical conventions 2Enumerations 2 Actions 2 Syntax 2 Cross-references 21.3Symbols 21.4Abbreviations 21.5Divergent views 2 2Safety 32.1Intended use 32.2Installation and startup 32.3General safety Notes 32.4Resistance to Aggressive Substances 3Hazardous voltage 3 3Getting Started 43.1Connection overview 43.2Mechanical connection 53.3Electrical connection 53.4Function ground 53.5IO-Link connection 53.6Digital Sensors 63.7Analogue Sensors 6 4IO-Link Interface 74.1IO-Link Data 74.2Process data inputs 74.3Process data outputs 84.4Parameter data/ On-request data 8Identification data 8 Inversion 9 Switch point enable 9 Switch point 94.5Errors 104.6Events 10 5Technical Data 115.1Dimensions 115.2Mechanical data 115.3Electrical data 115.4Operating conditions 115.5Function indicators 12Module LEDs 12 Digital Input LEDs 12 Analogue Input LEDs 12 6Appendix 136.1Type designation code 136.2Order information 13IO-Link Sensor-HubBNI IOL-709-… / BNI IOL-710-…1 Notes to the user1.1 Structure of theguide The Guide is organized so that the sections build on one another. Section 2 : Basic safety information. …………1.2 Typographicalconventions The following typographical conventions are used in this Guide. EnumerationsEnumerations are shown in list form with bullet points.• Entry 1, • Entry 2.Actions Action instructions are indicated by a preceding triangle. The result of an action is indicated by an arrow.Action instruction 1. Action result.Action instruction 2. SyntaxNumbers:Decimal numbers are shown without additional indicators (e.g. 123),Hexadecimal numbers are shown with the additional indicator hex (e.g. 00hex ).Cross-references Cross-references indicate where additional information on the topic can be found.1.3 SymbolsAttention!This symbol indicates a security notice which most be observed.NoteThis symbol indicates general notes.1.4 AbbreviationsBCD BNI CV DPP I-Port EMC FE IOL LSB MSB SP SPDU VVBinary coded switch Balluff Network InterfaceCurrent Version: BNI IOL 709… Direct Parameter Page Digital input portElectromagnetic Compatibility Function ground IO-LinkLeast Significant Bit Most Significant Bit Switch PointService Protocol Data UnitVoltage version: BNI IOL 710…1.5 Divergent views Product views and images can differ from the specified product in this manual. They serve only as an illustration.2 Safety2.1 Intended use The BNI IOL-… is a decentralized sensor input module which is connected to a host IO-Linkmaster over an IO-Link interface.2.2 Installation andstartup Attention!Installation and startup are to be performed by trained technical personnel only. Skilled specialists are people who are familiar with the work such as installation and the operation of the product and have the necessary qualifications for these tasks. Any damage resulting from unauthorized tampering or improper use shall void warranty and liability claims against the manufacturer. The operator is responsible for ensuring that the valid safety and accident prevention regulations are observed in specific individual cases.2.3 General safetyNotes Commissioning and inspectionBefore commissioning, carefully read the User's Guide.The system must not be used in applications in which the safety of persons depends on the function of the device.Intended useWarranty and liability claims against the manufacturer shall be rendered void by damage from:•Unauthorized tampering•Improper use•Use, installation or handling contrary to the instructions provided in this User's Guide.Obligations of the owner/operator!The device is a piece of equipment in accordance with EMC Class A. This device can produce RF noise. The owner/operator must take appropriate precautionary measures against this for its use. The device may be used only with a power supply approved for this. Only approved cables may be connected.MalfunctionsIn the event of defects and device malfunctions that cannot be rectified, the device must be taken out of operation and protected against unauthorized use.Approved use is ensured only when the housing is fully installed.2.4 Resistance toAggressiveSubstances Attention!The BNI modules always have good chemical and oil resistance. When used in aggressive media (such as chemicals, oils, lubricants and coolants, each in a high concentration (i.e. too little water content)), the material must first be checked for resistance in the particular application. No defect claims may be asserted in the event of a failure or damage to the BNI modules caused by such aggressive media..Hazardous voltage Attention!Disconnect all power before servicing equipment.NoteIn the interest of continuous improvement of the product,Balluff GmbH reserves the right to change the technical data of the product and the content of these instructions at any time without notice.IO-Link Sensor-HubBNI IOL-709-… / BNI IOL-710-…3 Getting Started3.1 Connectionoverview1 Mounting hole2 IO-Link interface3 Analogue input-Port 14 Status-LED: Analogue port5 Analogue input port 36 Status-LED: digital input Pin 27 Digital input port 18 Status-LED: Digital port Pin 49 Digital input port 3 10 Status LED “Power Supply”11 Digital input port 212 Digital input port 013 Analogue input port 214 Analogue input port 015 Label16 Status-LED …COM“17 Function ground connection3 Getting Started3.2 Mechanicalconnection The BNI IOL modules are attached using 3 M4 screws (Item 1, Fig. 3-1/3-2).3.3 Electricalconnection The Sensor Hub modules require no separate supply voltage connection. Power is provided through the IO-Link interface by the host IO-Link Master.3.4 Function groundThe modules are provided with a ground terminal.Connect Sensor Hub module to the ground terminal.NoteThe FE connection from the housing to the machine must be low-impedance and as short as possible.3.5 IO-LinkconnectionThe IO-Link connection is made using an M12 connector (A-coded, male).IO-Link (M12, A-coded, male)Pin Function 1Supply voltage, +24 V, max. 1.6 A 2 - 3 GND, reference potential4 C/Q, IO-Link data transmission channelConnection protection ground to FE terminal, if present. Connect the incoming IO-Link line to the Sensor Hub.NoteA standard sensor cable is used for connecting to the host IO-Link Master.IO-Link Sensor-HubBNI IOL-709-… / BNI IOL-710-…3 Getting Started3.6 Digital Sensors Digital input port (M12, A-coded, female)Pin Function 1 +24 V, 100 mA 2 Standard Input 3 0 V, GND 4 Standard Input 5 -NoteFor the digital sensor inputs follow the input guideline per EN 61131-2, Type 2.3.7 AnalogueSensors Analogue input port (M12, A-coded, female)Pin Function1 +24 V, 100 mA2BNI IOL-709...: 4 - 20 mABNI IOL-710…:n.c. 3 0 V, GND4BNI IOL-710...: 0 - 10 V BNI IOL-709…:n.c 5 FE, function groundNoteUnused I/O port sockets must be fitted with cover caps to ensure IP67 protection rating.NoteOvercurrent (> 25mA) on the BNI IOL-709 Module´s inputs can distort the measurement results of the other channels and it may leads to malfunction..4 IO-Link Interface4.1 IO-Link Data Baudrate COM2 (38,4 kBaud)Frame type 1Minimum cycle time 3 msProcess data cycle 30 ms with minimum cycle time4.2 Process datainputs BNI IOL-710-…/BNI IOL-709-…(Sensor-Hub digital/analog)Process data length 10Byte:Byte 0 Byte 17 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0InputPort7Pin4InputPort6Pin4InputPort5Pin4InputPort4Pin4SwitchPoint1Port3SwitchPoint1Port2SwitchPoint1Port1SwitchPoint1PortInputPort7.Pin2InputPort6.Pin2InputPort5.Pin2InputPort4.Pin2SwitchPoint2Port3SwitchPoint2Port2SwitchPoint2Port1SwitchPoint2PortByte 2 Byte 37 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0Error1Error2Error3MSBAnalogue valueLSBPort 0Byte 4 Byte 57 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0Error1Error2Error3MSBAnalogue valueLSBPort 1Byte 6 Byte 77 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0Error1Error2Error3MSBAnalogue valueLSBPort 2Byte 8 Byte 97 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0Error1Error2Error3MSBAnalogue valueLSBPort 3IO-Link Sensor-HubBNI IOL-709-… / BNI IOL-710-…4 IO-Link InterfaceInput: Input-Signal at Port and PinSwitch Point: The switch point bits show a switch pointoverrun. The switch point can be configuredby parameter ( see 0.0 - “Switch pointenable” and 0.0 - “Switch point”)Analogue value: VV: actual voltage value between0 and 1056 (1Bit = 0.01V)CV: actual current value between0 and 2150 (1Bit = 0.01mA)Error:• Error 1 • Error 2 • Error 3 Overcurrent/short circuit on sensor supply Measurement range overflow Measurement range undercut (only CV)4.3 Process dataoutputsThere are no outputs at BNI IOL-710-... and BNI IOL-709-... modules.4.4 Parameter data/On-request dataDPP SPDU Parameter DatawidthAccess Index Index Sub-indexIdentificationData07hex Vendor ID 2 ByteReadonly 08hex09hex Device ID 3 Byte0A hex0B hex10hex0 Vendor Name 8 Byte11hex0 Vendor text 16 Byte12hex0 Product Name 34 Byte13hex0 Product ID 21 Byte14hex0 Product text 34 Byte16hex Hardware Revision 3 Byte17hex0 Firmware Revision 3 ByteIdentification data Type Device ID VersionBNI IOL-710-000-K006 050201hex Voltage versionBNI IOL-709-000-K006 050202hex Current version4 IO-Link InterfaceDPPSPDUParameter Data width Value rangeDefault- valueIndex Index Sub-index P a r a m e t e r D a t a10hex 40hex640 1-16 Inversion 2 Byte 0000hex …FFFF hex 0000hex 11hex 12hex 41hex650 1-8 Switch point enable 1 Byte 00hex …FF hex 00hex 42hex660 Switch point 1 Port 0 2 Byte 0000hex … 03E8hex 0000hex 43hex670 Switch point 1 Port 1 2 Byte 0000hex … 03E8hex 0000hex 44hex680 Switch point 1 Port 2 2 Byte 0000hex … 03E8hex 0000hex 45hex690 Switch point 1 Port 3 2 Byte 0000hex … 03E8hex 0000hex 46hex700 Switch point 2 Port 0 2 Byte 0000hex … 03E8hex 0000hex 47hex710 Switch point 2 Port 1 2 Byte 0000hex … 03E8hex 0000hex 48hex720 Switch point 2 Port 2 2 Byte 0000hex … 03E8hex 0000hex 49hex73Switch point 2 Port 32 Byte0000hex … 03E8hex0000hexInversionInversion of the input signals:Byte 0Byte 176543217654321I n v e r s i o n P o r t 7 P i n 4I n v e r s i o n P o r t 6 P i n 4I n v e r s i o n P o r t 5 P i n 4I n v e r s i o n P o r t 4 P i n 4I n v e r s i o n S P 1 P o r t 3I n v e r s i o n S P 1 P o r t 2I n v e r s i o n S P 1 P o r t 1I n v e r s i o n S P 1 P o r t 0I n v e r s i o n P o r t 7 P i n 2I n v e r s i o n P o r t 6 P i n 2I n v e r s i o n P o r t 5 P i n 2I n v e r s i o n P o r t 4 P i n 2I n v e r s i o n S P 2 P o r t 3I n v e r s i o n S P 2 P o r t 2I n v e r s i o n S P 2 P o r t 1I n v e r s i o n S P 2 P o r t 0Switch point enableEnable the switch points by setting the enable bitsByte 07654321E n a b l e s w i t c h p o i n t 2 P o r t 3E n a b l e s w i t c h p o i n t 2 P o r t 2E n a b l e s w i t c h p o i n t 2 P o r t 1E n a b l e s w i t c h p o i n t 2 P o r t 0E n a b l e s w i t c h p o i n t 1 P o r t 3E n a b l e s w i t c h p o i n t 1 P o r t 2E n a b l e s w i t c h p o i n t 1 P o r t 1E n a b l e s w i t c h p o i n t 1 P o r t 0Switch pointByte 0Byte 1 7 6 5 4 3217654321Switch pointValue range (dec) CV= 400...2000 VV= 0 (1000)BNI IOL-709-… / BNI IOL-710-…4 IO-Link Interface4.5 Errors Byte 0Byte 1Device application error: 80hex11hex Index not available 12hex Subindex not available 30hex Value out of range4.6 EventsClass/QualifierCode (high + low)Mode Type InstanceP a r a m e t e r D a t aappears Error AL Device Hardware supply Supply low voltage U2 = supply + 24VC0hex 30hex 03hex 5000hex 0100hex 0010hex 0002hex F3hex5112hex disappears ErrorAL Device Hardware supply Supply low voltage U2 = supply + 24V80hex 30hex 03hex 5000hex 0100hex 0010hex 0002hexB3hex 5112hexappears Error AL Device Hardware supply supply peripheryC0hex30hex 03hex 5000hex 0100hex0060hexF3hex 5160hexdisappears ErrorAL Device Hardware supply supply periphery80hex30hex 03hex5000hex0100hex0060hexB3hex5160hex5 Technical Data5.1 Dimensions5.2 Mechanical data Housing Material Plastic, transparentIO-Link-Port M12, A-coded, maleInput-Ports 8x M12, A-coded, femaleEnclosure rating IP67 (only when plugged-in and threaded-in)Weight 90 gDimensions(L × W × H, excluding connector)115 × 50 × 30,8 mm5.3 Electrical data Operating voltage 18 ... 30,2 V DC, per EN 61131-2Ripple < 1 %Current draw without load ≤ 40 mA5.4 Operatingconditions Operating temperature -5 °C … +55 °C Storage temperature -25 °C … +70 °CBNI IOL-709-… / BNI IOL-710-…5 Technical Data5.5 FunctionindicatorsModule LEDs LED 5, IO-Link CommunicationStatus FunctionGreen No CommunicationGreen negative pulsed Communication OKRed Communication line overloadOff Module unpoweredLED 4, Power supply statusStatus FunctionGreen Module power is OKGreen slowly flashing Short circuitGreen rapidly flashing Module power supply < 18 VOff Module unpowered Digital Input LEDs LED 3, Input Pin 4 and LED 2, Input Pin 2Status FunctionYellow Input signal = 1Off Input signal = 0Analogue Input LEDs LED 1, Analogue input portStatus Signal 709 (4-20 mA) Signal 710 (0-10 V) Green ≥ 4 mA - ≤ 20 mA> 0,05 VRed < 4 mA - > 20 mA > 10,05 V6 Appendix6.1 Type designationcode6.2 OrderinformationType Order CodeBNI IOL-709-000-K006 BNI0007BNI IOL-710-000-K006 BNI0008BNI IOL-7xx-000-K006 Balluff Network InterfaceIO-Link interfaceFunctions710 = 8 digital inputs 0,15 A + 4 analog inputs 0 - 10 V709 = 8 digital inputs 0,15 A + 4 analog inputs 4 - 20 mAVariant000 = StandardvarianteMechanical configurationK006 =Plastic housing,Connectors:- BUS and Power supply: 1x M12x1, external thread- Input ports: 8x M12x1, internal threadBNI IOL-709-… / BNI IOL-710-… NotesBalluff GmbHSchurwaldstrasse 973765 Neuhausen a.d.F. GermanyTel. +49 7158 173-0 N r . 910442-726 E •01.125277 • E d i t i o n K 17 • R e p l a c e s E d i t i o n 1311 • S u b j e c t t o m o d i f i c a t i o n。
美推出纺织网印油墨3804低固化添加剂
据 了解 ，柯 尼 卡美能 达 的Ｂｉｈ ｂ ｏ ６ ｈ ｚ ｕ Ｐｒ Ｃ ５ ｃ
彩色数 字 印刷 机； Ｈｉ ｈ ｈｒ ｍａ ｆ ｇ Ｃ ｏ 碳粉 都是为 了满 Ｉ ］ 足包 装 市场 的平 面设 计需 求而 设 计的 。 由于 几乎 所有 的平 面设 计 工作 都是 在 电脑 上完 成 的 ，所 以 设计 师希 望 能通 过 印刷过 程 复制 出他 们 在显 示 器 上看 到的生 动色 彩 。
还将面临更为严格 的环保 法规 所带来的压 力 ，包括
ＣＰ Ｅ Ｉ同意 建 立 欧 洲造 纸 业 对 话 机 制
Ｃ Ｐ 欧洲造 纸工 业联 合会 ）近 日同意 了相 Ｅ Ｉ（ 关 企业 对 在欧 洲造 纸领 域组 织 社会 合作 伙伴 对话 的 申请 。这 个 决定 将 帮助 雇主 和工 会解 决造 纸业
欢 迎 的聚丙 烯 无纺 布袋 上面 印花 。３ ０ 苯二 甲酸 ８４
（ ） 固化 添加 剂 可以 将 常规 塑胶 油 墨的 固化 或 ＰＦ 低 者 熔 融温 度 降 至 ３ ０Ｆ ０。下 （４。 ） １ ９ Ｃ ，在 某些 情 况 下 ，甚 至低 至２ ５Ｆ （３ Ｃ ７ 。 １ ５ ）度 。
售和 广告 印刷 的需 求 比较 强 烈 。但 在今 年 ，新兴 媒体 取代 传统 印刷 品 的趋 势尤 为 明显 。” 自１９ ９４ 年以 来 ，美 国 ｌ 月份 的商 业 印刷 出货 量还 从未 低 ０
以 石 油 树 脂 为 基 础 原 料 ，然 而 ，理 光 新 开 发 的 “ｏＥｏ ｅ” （ ｆｒ ｔｎ ｒ 环境 友 好型碳 粉 ） ，包 括树脂 材 料在 内的生物 质 占了全部 总量 的２％。 ５
增 多 的客 户要 求开 发 出来 的一个 产 品 ，它能够 在 热 敏 感 基 板 上 印 刷 ，例如 １ ０ ０ ％涤 纶 或者 非 常受
氨捕获器[发明专利]
![氨捕获器[发明专利]](https://img.taocdn.com/s3/m/6f51d9ea16fc700aba68fc51.png)
专利名称：氨捕获器
专利类型：发明专利
发明人：克雷格·班克斯,阿塞那西奥斯·V·考里奥普拉斯,迪米特瑞奥斯·坎普瑞斯
申请号：CN201580000204.8
申请日：20150430
公开号：CN105431724A
公开日：
20160323
专利内容由知识产权出版社提供
摘要：一种氨捕获器，包括一个收集基体和一种固定在收集基体上的酸或单独的酸溶液。
一个用于氨检测的装置或套件包含捕获系统和一个氨气传感器。
一个检测氨的方法由以下几步组成：首先通过捕获系统收集气态氨；然后将氨与酸反应生成铵离子；最后检测铵离子。
捕获系统或装置用于氨的检测。
申请人：长沙三相医疗器械有限公司
地址：410083 湖南省长沙市中南大学本部化学化工学院
国籍：CN
代理机构：北京彭丽芳知识产权代理有限公司
代理人：汪永生
更多信息请下载全文后查看。
tb340成分
tb340成分摘要：1.TB340 的定义和背景2.TB340 的主要成分3.TB340 成分的作用4.TB340 的应用领域5.TB340 的优点和局限性正文：TB340，全称Terbium-Based Alloy Phase Stabilized by additions of Tantalum and Niobium, is a specific alloy that has been developed for various applications in the field of high-temperature superconductors.This alloy is known for its ability to maintain its structural and magnetic properties at high temperatures, which makes it an ideal choice for use in a variety of high-temperature applications.One of the primary components of TB340 is Terbium (Tb), which is a rare earth element that is known for its ability to improve the superconducting properties of an alloy.Tb is a heavy metal that has an atomic number of 65 and is often used in the production of high-temperature superconductors.Another important component of TB340 is Tantalum (Ta), which is a refractory metal that is known for its high melting point and excellentchemical stability.Ta is often used in the production of high-temperature superconductors because of its ability to improve the mechanical properties of an alloy.iobium (Nb) is another key component of TB340, and it is known for its ability to enhance the superconducting properties of an alloy.Nb is a refractory metal that has an atomic number of 41 and is often used in the production of high-temperature superconductors because of its ability to improve the mechanical and chemical properties of an alloy.TB340 is primarily used in the production of high-temperature superconductors, which are known for their ability to conduct electricity at high temperatures without any resistance.These superconductors are used in a variety of applications, including energy storage, power transmission, and medical imaging.One of the primary advantages of TB340 is its ability to maintain its structural and magnetic properties at high temperatures.This makes it an ideal choice for use in a variety of high-temperature applications.However, TB340 also has some limitations, such as its high cost and the fact that it can be difficult to work with.In conclusion, TB340 is a specific alloy that has been developed for various applications in the field of high-temperature superconductors.It contains a combination of Terbium, Tantalum, and Niobium, which enhance its superconducting and mechanical properties.TB340 isprimarily used in the production of high-temperature superconductors and has several advantages, such as its ability to maintain its structural and magnetic properties at high temperatures.However, it also has some limitations, such as its high cost and the fact that it can be difficult to work with.。
3溴4(三氟甲氧基)苯胺安全技术说明书MSDS
第一部分化学品及企业标识化学品中文名：3・澳・4・(三氟甲氧基)苯胺化学品英文名:3-Bromo-4-(trifluoromethoxy)anilineCASNo.:191602-54-7分子式：C7H5BrF3NO产品推荐及限制用途：工业及科研用途。
第二部分危险性概述紧急情况概述吞咽会中毒。
可能导致皮肤过敏反应。
造成严重眼刺激。
GHS危险性类别急性经口毒性类别3皮肤致敏物类别1严重眼损伤/眼刺激类别2标签要素：象形图：警示词：警告危险性说明：H301吞咽会中毒H317可能导致皮肤过敏反应H319造成严重眼刺激•预防措施：一一P264作业后彻底清洗。
——P270使用本产品时不要进食、饮水或吸烟。
——P261避免吸入粉尘/烟/气体/烟雾/蒸气/喷雾。
——P272受沾染的工作服不得带出工作场地。
-P280戴防护手套/穿防护服/戴防护眼罩/戴防护面具。
—事故响应：——P301+P310如误吞咽：立即呼叫解毒中心/医生——P33O漱口。
——P302+P352如皮肤沾染：用水充分清洗。
——P333+P313如发生皮肤刺激或皮疹：求医/就诊。
——P362+P364脱掉沾染的衣服，清洗后方可重新使用——P305+P351+P338如进入眼睛：用水小心冲洗几分钟。
如戴隐形眼镜并可方便地取出，取出隐形眼镜。
继续冲洗。
-P337+P313如仍觉眼刺激：求医/就诊。
•安全储存：-P405存放处须加锁。
•废弃处置：-P501按当地法规处置内装物/容器。
物理和化学危险：无资料。
健康危害：吞咽会中毒。
可能导致皮肤过敏反应。
造成严重眼刺激。
环境危害：无资料。
第三部分成分/组成信息急救：吸入：如果吸入，请将患者移到新鲜空气处。
皮肤接触*脱去污染的衣着，用肥皂水和清水彻底冲洗皮肤。
如有不适感，就医。
眼晴接触，分开眼睑，用流动清水或生理盐水冲洗。
如有不适感，就医。
食入,饮水，禁止催吐。
如有不适感，就医。
对保护施救者的忠告：将患者转移到安全的场所。
聚醚胺 ma340分子量
聚醚胺 ma340分子量
聚醚胺MA340是一种高分子化合物，具有特殊的分子结构和性质。
MA340的分子量较大，使其在许多领域都有广泛的应用。
下面将为您介绍一些有关MA340的知识。
MA340是一种聚醚胺，由乙二醇和脂肪酸酐反应合成而成。
它的分子量通常在1000到5000之间，具体取决于聚醚胺和脂肪酸酐的比例和反应条件。
MA340的分子量较大，使其具有较高的粘度和黏度，适用于一些特殊的应用场合。
MA340具有许多优异的性质，使其在化工、材料科学、医药等领域得到广泛应用。
首先，MA340具有良好的溶解性和分散性，能够与许多溶剂和颗粒物质混溶。
这使得MA340可以作为乳化剂、分散剂和增稠剂在化妆品、涂料和医药制剂中使用。
MA340还具有优异的稳定性和耐候性，能够在不同的环境条件下保持其性能稳定。
这使得MA340可以用于制备耐候性好的涂料、粘合剂和塑料制品。
另外，MA340还具有较好的热稳定性和耐腐蚀性，使其在高温和腐蚀性介质中表现出色。
由于MA340分子量较大，它还具有一定的粘附性和吸附性。
这使得MA340可以用作表面活性剂、润湿剂和粘合剂，广泛应用于纺织、造纸和印刷等行业。
同时，MA340还具有一定的保湿性和保护性，可用于制备护肤品和保健品。
总的来说，聚醚胺MA340是一种分子量较大的高分子化合物，具有优异的溶解性、分散性、稳定性和耐候性。
它在化工、材料科学、医药等领域有广泛的应用，为各行各业提供了许多创新的解决方案。
希望通过以上介绍，您对MA340有了更深入的了解。
tb340成分
tb340成分TB340是一种化学成分，它具有多种应用领域和功能。
本文将为您介绍TB340的特性、应用和相关研究进展，以及对环境和健康的影响。
一、TB340的特性TB340是一种无色无味的液体，其化学结构为C10H12O3。
它具有良好的溶解性，可溶于乙醇、醚类和酮类溶剂。
TB340的密度为1.12 g/cm³，沸点为220°C，熔点为-20°C。
它在常温下稳定，不易挥发或分解。
二、TB340的应用1. 作为溶剂：TB340具有良好的溶解性，广泛应用于化学合成、涂料、油墨和胶黏剂等工业领域。
它可以作为溶剂来溶解和稀释不同的物质，提高产品的质量和性能。
2. 作为防腐剂：TB340具有优异的防腐性能，可用于木材、纺织品和皮革等材料的防腐处理。
它可以有效抑制细菌和真菌的生长，延长产品的使用寿命。
3. 作为表面活性剂：TB340具有较强的表面活性，可用于洗涤剂和个人护理产品中。
它能够降低液体的表面张力，提供良好的清洁效果和稳定的泡沫。
三、TB340的研究进展近年来，TB340的研究逐渐受到关注，并取得了一些重要进展。
1. 有机合成：研究人员发现TB340可作为催化剂或反应中间体，在有机合成中发挥重要作用。
它能够催化各种有机反应，促进化学反应的进行，并提高反应的选择性和产率。
2. 环境影响：一些研究表明，TB340在大量使用时可能对环境造成一定影响。
它可能对水体生物产生毒性作用，对土壤生态系统产生累积效应。
因此，在使用和处理TB340时，需要采取相应的环境保护措施。
3. 安全性评估：针对TB340的安全性问题，研究人员进行了一系列的评估和研究。
目前，尚未发现TB340对人体健康产生明显的危害。
但在使用过程中，仍需注意避免接触眼睛、皮肤和呼吸道，以防止不必要的危险。
四、TB340的未来发展随着科学技术的不断进步，TB340的应用前景将更加广阔。
研究人员正在努力开发新的合成方法和应用领域，以提高TB340的性能和功能。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Completely made and assembled in the U.S.A.340/342380/382Sure Seal SeriesNylon Coated Disc Butterfly ValvesSizes 2"-12" 125/150 ANSITeflon ¤ is a registered trademark of E.I. DuPont Co.A superior nylon coated disc valve for industrial applications, engineered for higher Cv ratings than any nylon disc valve on the market today.INCORPORATEDTMISO 9001certifiedSURE SEAL INCORPORATED IS PROUD TO BES C H E D U L E 40S C H E D U L E 80A Superior Valve at a Competitive PriceThe Sure Seal Valve sets thestandard in the butterfly valve industryThe Superior Nylon Coated Disc Valve340/342Sure Seal SeriesSizes 2"-12"PATENTED 380/382PATENTEDTeflon¤ and Viton¤ are registered trademarks of E.I. DuPont Co.Every valve is tested to 110% of full pressure rating.Patent #5207411R R E I NC O P O A T DGol d S e a l o f Ex c e ll e nc e a n dPe rf o rm a n c eSTANDARD FEATURESTop Plate - Machined to standardized and ISO drilling pattern allowing manual handle kits, and actuation interchangeability.Stem Bushing - Composed of full strength, corrosion resistant ertalyte, stem bushings absorb operator side thrust. Top bushingcomes standard in all valves to ensure trouble free valve operation.Stem-Seal - A third seal ensuring absolute seal externally or internally for vacuum orpressure service. Available in Buna-N, EPDM, or Viton ¤.Seat - EPDM, Viton ¤, and Sure Seal s Special Abrasion Resistant formulated blend of FDA approved Nitrile, along with 12 other standard compounds to meet your application.Hub Seal or Primary Seal - Occurs when contact is made between the disc hub and the flat surface of the seat. Hub/seat sealsprevent product from attacking stem or body.Body - Lug style has drilled and tapped lugs meeting ANSI 125 and 150 flange standards. Two piece body allows ease of seat replace-ment. Lug body standard with Nodular Iron. Wafer body standard with Nodular Iron also available in Aluminum, Anoidized Aluminum, Aluminum Bronze, Stainless Steel, Teflon ¤ Coated and several Corrosion Resitant platings.Disc/Stem - Sure Seal s standard is Nylon 11, a vegetable based thermoplastic which is USDA approved. Nylon 11 is resistant tofungus growth and molds. Corrosion resistant yet maintains a very durable surface and a low friction coefficient. This material has been tested under adverse conditions withoutcorrosion to underlying metal surfaces. Other materials are also available.Flange Seal - Sealing O-Ring of resilient seat which provides an absolute seal to all flanges within specifications.Bottom Stem Bushing - Oil impregnated bronze bushing for less torque and longer valve life.Technical DataSure Seal Nylon 11 CoatingSure Seal s standard is Nylon 11, a vegetable based thermoplastic which is USDA approved. Nylon 11 is resistant to fungus growth andmolds. Corrosion resistant yet maintains a very durable surface and a low friction coefficient. This material has been tested under adverse conditions without corrosion to underlying metal surfaces. Other materials are also available.AccessoriesThe Series 340/342 and 380/382 arecompatible with all Sure Seal accessories include direct mounting actuators. Consult factory or your Sure Seal dealer for more information and technical data.Flow Coefficient (rated Cv)Valve Size15°20°30°40°50°60°70°80°90°2.312 2.8111.1319.453353941672773.7287.1828.8150861372444357204 1.3513.6254.79516426046482613665 2.1821.9487.67153263416745132621926 2.9129.021162023485519851757290185.4154.182163796501029184032765416108.6386.42345605103616432938522686401212.48124500875150123774253756612511%Cv vs 90°Cv=0.114712193460.5100Rated Cv = The volume of water in U.S. gallons per minute that will pass through a given valve opening with a pressure of 1 lb. per square inch.Valve Size501001501755021251301351401252.51952052152201953260275290300260440042545046526756156707257554106805915100010455378147516501825191598310224025202800294014931234203870432045452280Pressure RatingsBi-directional bubble tight shut off in closed position, 2-12 inch/50-300 mm valves have a 175 psig/12 bar rating.In dead end service applications for 2-12 inch/50-300 mm, valves are rated at 150psig/10 bar. All pressure ratings are based on standard disc diameters. Sure seal offers a reduced disc diameter for low pressure applications which if applicable can reduce seat wear and actuator size.Velocity LimitsFor on-off serviceFluids: 30 feet per second (9m/sec.)Gases: 175 feet per second (54m/sec.)A N G L E O F D I S C O P E N I N GReduced Disc Dia.∆P (psi)Full Rated Pressure Valves∆P (psi)Seating and Unseating Torques (lb-in)SpecificationsSeries 340/342 and 380/382Ductile Iron or Aluminum body, wafer or lug style. Flange drilling holes meet ANSI 125/150 specifications and have line up ears for easy installation.Pressure ratings of 175 psi, lug bodies for dead end service 150 psi.Bottom bushings are oil impregnated bronze.Top plate drilling pattern conforms to standard hole drilling patterns and ISO drill patterns.Schedule 40 or Schedule 80 compatible.All valves are tested to 110% of full pressure rating.Parts1Retaining Ring2Flat Washer3Retaining Ring4Upper Disc Stem5Bushing6Packing7Body8Seat9Disc10Lower Disc Stem11Oil Impregnated Bushing 12Bottom Stem Plug Material Selection2" - 12"; 50mm - 300mmBody:Ductile Iron ASTM A536Aluminum ASTM B26Seat:Viton GF¤Food Grade:EPDMBUNA-N (Nitrile)White BUNA-N (Nitrile)Stem:17-4 Ph Condition A Stainless SteelASTM A564316 Stainless SteelASTM A276 Type 316Disc:Ductile Iron, Nylon 11 Coated,ASTM A536Ductile Iron ASTM A536Aluminum Bronze ASTM B148-953316 Stainless Steel ASTM A351 CF8MTemperatureRange of SeatsMAX.MIN.Viton+350¡ F0¡F177¡C-18¡CEPDM+250¡ F-40¡F121¡C-40¡CBUNA-N+250¡ F0¡FNitrile121¡C-18¡C123456789101112Why Sure Seal Nylon Coated Disc Valves?Increased FlowSure Seal s two-piece stem design allows for a thinner disc than any available valve on the market today. Thinner disc equals more flow, less stress on the valve and seat and greater Cv values.Fastest Field Assembly in the IndustrySure Seal s unique design allows for quick field assembly and assures a blow out proof stem.Dual Drilled Top PlateBoth Sure Seal sstandard and ISO drilling patterns are available on every valve.Stronger Lower Stem Connection and Bronze BushingSure Seal s two-piece stem design allows for a stronger lower stem connection. Other styles of valves decrease the size of their lower stemfor installation purposes,but with Sure Seal you get the full diameter. Also note the addition of an oil impregnated bushing in the lower stem. This bushing makes stem freeze up, corrosion and gaulding a thing of the past.Sure Seal’s Disc Design Sure Seal’s Bottom Stem Competitor’s Bottom Stem Competitor’s Disc DesignCompetitor’sIs Your Valve Off ScheduleSure Seal offers a Schedule 40 Valve as well as a Schedule 80 model. In this competitve market place every Cv equals money. Don’t waste your time and money with a valve that doesn’t fit your needs. Specify the right valve for the right job.Schedule 80 ValveSchedule 40 PipeS c h e d u l e 80 O p e n i n g S c h e d u l e 40 O p e n i n gSure SealSchedule 40 ValveSchedule 40 PipeS c h e d u l e 40 O p e n i n gTop and BottomLine up EarsAn exclusive feature of Sure Seal. Take the hassel out of getting your valvesinstalled properly.No. Holes BC Hole Dia.ISO BC ISO Hole Dia.Sure Seal Series 340/342 and 380/382Valve SizeA B C D E FG 340/342G 380/382H 340/342H 380/382J24.00.3751.625.5631.2503.9381.6881.3752.1252.0004.0252.54.00.3751.750.5631.2504.500—2.062—2.5004.87534.000.3751.750.5631.2504.8752.8752.5633.1253.0005.25044.000.4382.000.6251.2506.0003.8753.6254.1254.0006.75054.000.4382.125.6251.2506.0005.0004.7505.1885.0007.62564.000.4382.125.6251.2506.5006.0005.5006.1255.7508.62586.000.5002.500.7501.2508.3138.0007.5008.1257.75010.812106.000.6252.500.8751.2509.00010.0639.59410.1259.75013.375126.0003.0001.1252.00010.62511.93811.56312.09311.75016.188V a l v e D i m e n s i o nTop Plate Drilling2.543.250.4382.760.38243.250.4382.760.38343.250.4382.760.38443.250.4382.760.38543.250.4382.760.38643.250.4382.760.38845.000.5634.020.411045.000.5634.020.411245.000.5634.020.41340/380342/382Weight in Pounds*2.58102683911411175152161726829421044651285108GENERAL NOTES:C = INSTALLED WIDTHG = MINIMUM ALLOWABLE INSIDE DIA. OF PIPE OR MATING FLANGE 2" - 10" D = STEM CONNECTION DIA.; B = FLATS12" D = STEM CONNECTION DIA.; KEYWAY = .250 X .250Consult Factory for Aluminum weights available only in 340, 380 wafer style.*Weight based on Nodular Iron Body and Nylon Coated Nodular Iron Disc.Only available in 380/382 SeriesAC DEFJH G BACBolt Circle No. Holes Tap Lug Tapping Data2.55.500424.750436.000447.500858.500869.5008811.75081014.250121217.00012.625-11 UNC .750-10 UNC .875-9 UNCSTEMB Making a big difference to your bottom line.1-800-382-1604Rt. 2, Box 2242 • Mineral Point, Missouri 63660 • (573) 438-5000 • Fx (573) 438-4853 • ssi@Purchasers are expected to make their own tests to determine the suitability of these products for their particular purposes. The data represented in this flyer is for general information only. Manufacturer is not responsible for acceptability of these products in regard to individual system requirements. For specific performance data and correct materials selection, please contact your Sure Seal Dealer. ©1998 Sure Seal, Incorporated • Printed in the USA:OPW19266 :021-******** info@。