CCNA第三学期期末

合集下载

CCNA期末考试试题

1、要求:(1)VTP域名为benet;密码为123;启用修剪;(2)配置2台3层交换机为VTP的server模式;配置2层交换机为VTP的client模式;(3)设置SW-3L-1是VLAN 2－6的生成树根网桥;设置SW-3L-2是VLAN 7－11的生成树根网桥;在2层交换机上配置速端口与上行速链路;(4)配置路由器接口的IP地址;配置路由器启动RIP路由协议;配置路由器上的默认路由，指向10.1.1.1/24;(5)在3层交换机上配置各VLAN的IP地址;配置两台3层交换机之间的EthernetChannel;(6)配置3层交换机的路由接口;在3层交换机上配置RIP路由协议（1）（2）○1SW1-3L 配置vtp域名benetpassword 123 Server模式SW2-3L同样配置○2SW1-3L启用修剪SW2-3L同样配置○3SW3-2L配置vtp的client模式、SW4-2L、SW5-3L、SW6-3L相同配置（3）设置SW-3L-1是VLAN 2－6的生成树根网桥;设置SW-3L-2是VLAN 7－11的生成树根网桥;在2层交换机上配置速端口与上行速链路;○1SW-3L-1是VLAN 2－6的生成树根网桥;;○2设置SW-3L-2是VLAN 7－11的生成树根网桥○3SW3-2L配置速端口与上行链路，SW4-2L、SW5-2L 、SW6-2L上同样配置（4）配置路由器接口的IP地址;配置路由器启动RIP路由协议;配置路由器上的默认路由，指向10.1.1.1/24○1路由器上配置ip地址○2路由器上配置默认路由和RIP○3SW1-3L各vlan的ip地址○4SW2-3L各vlan的ip地址（5）在3层交换机上配置各VLAN的IP地址;配置两台3层交换机之间的EthernetChannel ○1在SW1-3L配置EthernetChannel;○2在SW2-3L配置EthernetChannel;（6）配置3层交换机的路由接口;在3层交换机上配置RIP路由协议○1SW1-3L上配置路由接口○2SW2-3L上配置路由接口○3SW1-3L上的RIP配置○4SW2-3L上的RIP配置○5在SW1-3L验证RIP○6在SW2-3L验证RIP2、要求:如图所示，四台路由器R1，R2，R3以及R4运行OSPF协议（要求发布各路由器的loopback0地址），R1与R2属于Area1，R2与R3属于Area0，R3与R4属于Area2。

思科ccna第3学期_final_第1套_V_4

What is the purpose of VLAN trunking?It improves network performance by reducing broadcast traffic.It selects the best path to transmit data in a switched network.It carries the traffic of multiple VLANs through a single link.It avoids spanning tree loops in a switched network.Refer to the exhibit. Both switches are configured with default bridge priority. Which port will act as the STP root port if all links are oper Fa0/1 interface of S1Fa0/2 interface of S1Fa0/1 interface of S2Fa0/2 interface of S2Refer to the exhibit. The network administrator wants to configure Switch1 to allow SSH connections and prohibit Telnet conne ctions. How sh administrator change the displayed configuration to satisfy the requirement?Use SSH version 1.Reconfigure the RSA key.Configure SSH on a different line.Modify the transport input command.Refer to the exhibit. Which two facts about STP can be determined from the displayed output? (Choose two.)Switch S1 has the lowest configured STP priority in the network.Switch S1 is configured as the root bridge for VLAN1.Fa0/21 is the root port of switch S1.Fa0/22 is the redundant link.Fa0/24 is considered the best path to the root bridge.Which statement correctly describes the spanning-tree path cost?It is calculated based on the total number of switches connected in a loop.It is calculated based on the utilization of all the switches along a given path.It is calculated based on the bridge priority of the switches along a given path.It is calculated based on the sum of the port cost value, determined by link speed, for each switch port along a given path What are two requirements for configuring inter-VLAN routing using the router-on-a-stick model? (Choose two.)Each subinterface should be configured with its own IP address, subnet mask, and unique VLAN assignment.The physical interface of the router must be connected to a trunk link on the adjacent switch.The number of physical interfaces on the router should match the number of VLANs.Different static VLANs should be assigned to different interfaces of the router.The router should be configured as the VTP serverRefer to the exhibit. Which two options correctly describe the router configuration that is shown? (Choose two.)Routing between the 192.168.1.0 and 192.168.3.0 networks will not succeed until a routing protocol is configured on the route r.VLANs have not been appropriately configured on the router subinterfaces.The configuration is appropriate for a router-on-a-stick network design.Trunking has been appropriately configured on the router subinterfaces.An IP address should be applied to interface Fa0/1 for routing to occurRefer to the exhibit. What is true of the configuration of switch S1?A Cisco proprietary protocol is in use for ports Fa0/1 and Fa0/3.Switch ports Fa0/1 and Fa0/3 have been configured with the switchport mode access command.Untagged frames received on ports Fa0/1 and Fa0/3 will be placed on VLAN 1.Switch ports Fa0/1 and Fa0/3 are configured to carry data from multiple VLANs.Refer to the exhibit. Switches S2 and S3 are properly connected using an ethernet cable. A network administrator has configured both s is unable to propagate VLANs to S2. What could be the reason for this?The VTP configuration revision is different on both switches.The VTP domains are different on both switches.VTP pruning is disabled.VTP v2 is disabled.Refer to the exhibit. Router R1 is properly configured for router on a stick inter-VLAN routing, but PC1 is unable to ping PC2. What needs problem?Rename VLAN1.Connect one more port of S1 to R1.Configure the Fa0/1 port of S1 as a trunk port.Move the Fa0/0 interface of R1 to another VLAN.Refer to the exhibit. Router R-West and switch S-West1 are connected via a single ethernet cable between the router interface fa0/0 an fa0/1. The router and switch have been configured with the commands that are displayed in the exhib it. The network administrator ente trunk command and receives the output as shown. What is the cause of the "not-trunking" status for switch port Fa0/1?The trunk is established, but no VLANs have been configured to use it.The router is missing the dynamic trunking protocol statements necessary to form a trunk.Because the router does not support Dynamic Trunking Protocol, the trunk has not been established.The router, the switch, or both must be configured with the dynamic desirable option for Dynamic Trunking Protocol to establish aRefer to the exhibit. All trunk links are operational and all VLANs are allowed on all trunk links. An ARP request is sent by computer 5. W receive this message?only computer 4computer 3 and RTR-Acomputer 4 and RTR-Acomputer 1, computer 2, computer 4, and RTR-Acomputer 1, computer 2, computer 3, computer 4, and RTR-Aall of the computers and the routerRefer to the exhibit. A network administrator enters the displayed commands to configure VLAN 30. What is the result of running these commVLAN 30 will be added to S1, S2, and S3, but not to S4.VLAN 30 will be pruned from the VLAN database of S3.VLAN 30 will be added to the VLAN database of S3 but will not be propagated to S4, S2 or S1.VLAN 30 will not be added to the VLAN database of S3 and an error message will be displayedRefer to the exhibit. VTP pruning is enabled in the VTP domain that is shown. How will switch ST-1 handle Layer 2 broadcast traf host A on switch ST-C?It will be dropped.It will be forwarded out port Fa0/5 only.It will be forwarded out ports Fa0/5 and Fa0/10.It will be forwarded out ports Fa0/5, Fa0/10, and Fa0/15Refer to the exhibit. The devices in the network are operational and configured as indicated in the exhibit. However, hosts A and D other. What is the most likely cause of this problem?The link between the switches is up but not trunked.The Fa0/11 interface of Switch1 is not configured as a trunk.Hosts A and D are configured with IP addresses from different subnets.VLAN 20 and VLAN 30 are not allowed on the trunk between the switches.After unpacking a new Linksys WRT300N wireless multifunction device, a user needs to change the default administrator passwor d and make other configuration changes. What must the user do to access the device in order to make these changes?Use a wireless client to associate with the WRT300N and then open a HyperTerminal session with the device.Establish a wired connection with the device and then reboot the attached computer to launch the configuration software.Establish a wired connection from a computer in the same IP subnet as the WRT300N and enter the default IP address of the device into a web browser on the computer.Modify the TCP/IP properties of the computer that is connected to the WRT300N so that the computer and the WRT300N exist on the same network. Then reboot the computer to establish a connection.Refer to the exhibit. How is port Gi1/1 on SWT-A functioning in the spanning-tree topology?It is sending and receiving data frames.It is receiving BPDUs, but not sending data frames.It is participating in the election process by forwarding the BPDUs it receives.It is receiving BPDUs and populating the MAC address table, but not sending data.Refer to the exhibit. The switches have been configured as shown. The hosts that are connected to switch 101-2FL are not able to communicate with the hosts in their corresponding VLANs that are connected to switch 101-3FL. What should be done to fix the problem?Configure port Fa0/2 on switch 101-3FL as a static trunk link.Introduce a Layer 3 device or a switch with Layer 3 capability into the topology.Utilize the switchport trunk allowed vlan all command on switch 101-3FL to permit the VLAN traffic.Apply IP addresses that are in the same subnet to the interfaces that are used to connect switches 101-2FL and 101-3FLAfter listening for the presence of a signal on the network media, hosts A and C transmit data at the same time. In what two ways do the hosts respond to this situation? (Choose two.)The hosts transmit a jam signal to ensure that all hosts on the network are aware that a collision has occured.Because they are operating in full-duplex mode, the hosts resume listening for traffic in preparation for sending future messages.Because the hub will temporarily block traffic from one of the hosts, that host will be allowed to transmit once the wire is clear.Hosts A and C are assigned shorter backoff values to provide them priority to access the media for retransmission.After the backoff period of a host, the host checks to determine if the line is idle before retransmittingRefer to the exhibit. Hosts PC_A and PC_B send traffic simultaneously, and the frames from the transmitting stations collide.What is the last device to receive the collision?hub HB1switch SW1router R1switch SW2router R2switch SW4Refer to the exhibit. Switch SW2 has been newly purchased and added to the network. What configuration should be applied to SW2 so thatit participates in the same VTP domain as switch SW1, receives VLAN information from SW1, and synchronizes VLAN information?Disable VTP pruning on SW2.Configure SW2 in VTP transparent mode.Configure SW2 with the VTP domain password.Configure SW2 as a VTP server with a higher revision numberWhen configuring a router to act as an SSH server, what should be configured before issuing the crypto key generate rsacommand?the security domain namethe VTP domain namethe IP domain namethe host nameRefer to the exhibit. The switch VTY lines have been properly configured, but PC1 is unable to remotely manage the switch. How can this problem be resolved?Configure the Fa0/1 interface of the switch in trunk mode.Configure a default gateway on the switch.Configure the native VLAN on the switch.Configure the Fa0/1 interface of the switch to allow all VLANsRefer to the exhibit. A network administrator has segmented the network into two VLANs. The connected hosts can only access r esources in their own VLAN. What is the most scalable and cost effective solution to allow inter-VLAN communication in this network?Replace S1 with a router that has one FastEthernet interface for each PC.Add a second switch and divide the PCs so that each VLAN is connected to its own switch.Configure a router with two subinterfaces on one of its FastEthernet ports and connect it to S1 using a trunk link.Connect a router to a port on S1 and assign the IP address of VLAN1 to the connecting router interfaceRefer to the exhibit. An administrator documented the output of a CAM table from an Ethernet switch as shown. What action will the switch take when it receives the frame shown at the bottom of the exhibit?discard the frameforward the frame out port 2forward the frame out port 3forward the frame out all portsforward the frame out all ports except port 3add station 00-00-3D-1F-11-05 to port 2 in the forwarding tableWhich statement regarding the service password-encryption command is true?The service password-encryption command is entered at the privileged EXEC mode prompt.The service password-encryption command encrypts only passwords for the console and VTY ports.The service password-encryption command encrypts all previously unencrypted passwords in the running configuration.To see the passwords encrypted by the service password-encryption command, enter the no servicepassword-encryption commandWhich statement correctly describes the function of a Layer 2 switch?It performs switching and filtering based on the destination network layer address.It automatically uses STP to prevent switching loops in redundant topologies.It uses VTP to allow data from multiple VLANs to travel across a single link.It routes packets between different LAN segmentsWhich three statements are correct concerning the default configuration of a new switch? (Choose three.)It is configured in VTP server mode.STP is automatically enabled.The first VTY line is automatically configured to allow remote connections.VLAN1 is configured with a management IP address.All switch ports are assigned to VLAN1.The enable password is configured as ciscoRefer to the exhibit. How will switch S2 manage traffic coming from host PC1?S2 will drop the traffic, unless it is management traffic.S2 will tag the frame with VLAN ID 99 when it forwards it over the trunk link.S2 will leave the traffic untagged when it forwards it over a trunk link.S2 will tag the traffic with the highest VLAN ID value when it forwards it over the trunk link.Refer to the exhibit. The network administrator needs to remove the east-hosts VLAN and use the switch port from that VLAN in one of the existing VLANs. Which two sets of commands should be used when completely removing VLAN 2 from S1-Central while leaving the switch and all its interfaces operational? (Choose two.)S1-Central>enableS1-Central# reloadS1-Central>enableS1-Central# erase flash:S1-Central>enableS1-Central# delete flash:vlan.datS1-Central>enableS1-Central# configure terminalS1-Central(config)# no vlan 2S1-Central>enableS1-Central# configure terminalS1-Central(config-if)# interface fastethernet 0/1 S1-Central(config-if)# switchport access vlan 3Refer to the exhibit. The network administrator configures both switches as displayed. However, host C is unable to ping host D and host E is unable to ping host F. What action should the administrator take to enable this communication?Include a router in the topology.Associate hosts A and B with VLAN 10 instead of VLAN 1.Remove the native VLAN from the trunk.Configure one trunk port in the dynamic desirable mode.Add the switchport nonegotiate command to the configuration of S2Which two statements are correct about wireless infrastructure components? (Choose two.)An AP converts the TCP/IP data packets from their 802.11 frame encapsulation format to the 802.3 Ethernetframe format on the wired Ethernet network.A wireless AP does not require any physical connection to allow wireless clients to access the Internet.An AP is a layer 2 device, similar to a switch, that provides dedicated bandwidth to each connected wireless host.Collisions do not occur between wireless NICs and APs.The wireless router performs the roles of AP and router.Refer to the exhibit. The switches are configured for VTP as shown. Which two statements correctly describe the operation of these switches? (Choose two.)A new VLAN can be added to Switch1 and that information will be added only to Switch2.A new VLAN can be added to Switch1 and that information will be added to Switch2 and Switch4.An existing VLAN can be deleted from Switch4 and that VLAN will be deleted from Switch1 and Switch2.An existing VLAN can be deleted from Switch2 and that VLAN will be deleted from Switch1 and Switch4.A new VLAN can be added to Switch4 and that information will be added to Switch1, Switch2, and Switch3.A new VLAN can be added to Switch3 and that information will be added to Switch1, Switch2, and Switch4A new switch is to be added to an exis ting network in a remote office. The network administrator does not wantthe technicians in the remote office to be able to add new VLANs to the switch, but the switch should receive VLAN updates from the VTP domain. Which two steps must be performed to configure VTP on the new switch to meet these conditions? (Choose two.)Configure an IP address on the new switch.Configure the existing VTP domain name on the new switch.Configure all ports of both switches to access mode.Configure the new switch as a VTP client.Enable VTP pruningWhich two statements describe Spanning Tree Protocol? (Choose two.)It is only used at Layer 2.It is configured on routers.It eliminates Layer 2 loops in network topologies.It limits the number of valid MAC addresses allowed on a port.It allows VLAN information to propagate to other switches in the network.Refer to the exhibit. Which switch will be elected as the root bridge of the spanning tree topology?Cat-ACat-BCat-CCat-DRefer to the exhibit. What three statements describe why Host1 and Host2 are unable to communicate? (Choose three.)The switch ports are on different VLANs.The switch IP address is on the wrong subnet.The hosts are configured on different logical networks.A router is required to forward traffic between Host1 and Host2.The VLAN port assignments must be contiguous for each VLAN.The host default gateway addresses must be on the same logical network.Refer to the exhibit. A new host needs to be connected to VLAN 3. Which IP address should be assigned to this new host?192.168.1.22 /28192.168.1.31 /28192.168.1.32 /28192.168.1.52 /28192.168.1.63 /28Refer to the exhibit. Router RA receives a packet with a source address of 192.168.1.65 and a destination address of 192.168.1.161. What will the router do with this packet?The router will drop the packet.The router will forward the packet out interface FastEthernet 0/1.1.The router will forward the packet out interface FastEthernet 0/1.2.The router will forward the packet out interface FastEthernet 0/1.3.The router will forward the packet out interface FastEthernet 0/1.2 and interface FastEthernet 0/1.3Refer to the exhibit. On which of the devices in this network should routing between VLANs take place?the core layer devicesthe access layer devicesthe distribution layer devicesthe core and distribution layer devicesRefer to the exhibit. The teacher host is connected to port Fa0/7 on switch STW. A student has decided to share access to the Internet by attaching a hub and laptop to STW as shown. What will be the result of the student making this connection?The Fa0/7 port of STW will be shutdown.The student will gain full access to the Internet.Both the teacher and student will be able to receive data but only the teacher will be able to send.The frames from the laptop will be dropped, but the teacher host will maintain connectivity with the network.Refer to the exhibit. In what two ways will the router handle VLAN traffic that is received on the trunk? (Choose two.)Traffic to VLAN 1 received by the router interface Fa0/0 will be dropped by the router.Because interface Fa0/0 requires an IP address, the router will not be able to route between the VLANs.Packets that are received from network 192.168.20.0 /24 will be handled by subinterface Fa0/0.20.The router will use subinterface MAC addresses to identify the VLAN traffic that is received on the physical interface.The router will continue to process traffic from the attached VLANs even if the physical interface goes downRefer to the exhibit. Switch SW-A is to be used as a temporary replacement for another switch in the VTP Studentdomain. What two pieces of information are indicated from the exhibited output? (Choose two.)The other switches in the domain can be running either VTP version 1 or 2.There is a risk that the switch may cause incorrect VLAN information to be sent through the domain.VTP will block frame forwarding on at least one redundant trunk port that is configured on this switch.VLAN configuration changes made on this switch will be sent to other devices in the VTP domain.This switch will update its VLAN configuration when VLAN changes are made on a VTP server in the same domainWhat are three benefits of employing a hierarchical network design? (Choose three.)Hierarchically designed networks can more easily be expanded to suit future needs.Hierarchical design models enhance existing bandwidth through the use of link aggregation.The hierarchical model allows for specialized functionality at each layer, simplifying devicemanagement.Use of a hierarchical design allows replacement of redundant devices with high-capacity network equipment.A hierarchical design uses firewalls instead of complicated port-based and distribution layer securitypolicies.The hierarchical model allows the use of high-performance switches at all design layers, thus allowing for a fully-meshed topologyRefer to the exhibit. Hosts A and B attempt to transmit a frame at the same time and a collision occurs. When will host D be able to transmit?immediatelyafter sending its jam signalafter host A and host B have completed transmissionafter the jam signal clears and its backoff delay expiresWhat provides an authentication mechanism for 802.11-based wireless networks?DSSSOFDMSSIDWPARefer to the exhibit. What is the effect of setting the security mode to WEP on the Linksys integrated router?WEP identifies the wireless LAN.WEP allows the access point to inform clients of its presence.WEP translates IP addresses into easy-to-remember domain names.WEP encrypts data between the wireless client and the access point.WEP ensures that only authenticated users are allowed access to the WLAN.WEP translates an internal address or group of addresses into an outside, public address.Refer to the exhibit. SW-T has been configured with a single trunking interface. Which VLANs will be allowed across the trunk?Only VLAN 1 will be allowed across the trunk.All configured VLANs will be allowed across the trunk.Only the native VLAN will be allowed across the trunk.Only the the management and native VLANs will be allowed across the trunk.Only VLANs that are configured on the VTP server in the dom ain will be allowed across the trunkRefer to the exhibit. What does the term DYNAMIC indicate in the output that is shown?This entry can only be removed from the MAC address table by a network administrator.When forwarding a frame to the device with address 0060.5c5b.cd23, the switch does not have to perform a lookup to determine the final destination port.Only the device with MAC address 0060.5c5b.cd23 will be allowed to connect to port Fa0/18.The switch learned this MAC address from the source address in a frame received on Fa0/18.Refer to the exhibit. What is the purpose of the configuration commands that are shown?to activate port Fa0/10to make the port a member of VLAN 30to activate port security on port Fa0/10to add VLAN 30 to the trunk that is connected to port Fa0/10。

CCNA第三学期期末答案

假设没有使用 VLSM，添加 ip route 172.16.64.0 255.255.240.0 serial0/0 命令会对网络中正在工作的路由器造成什么影响？3目的地址处于 172.16.64.1 到 172.16.80.254 之间的所有数据包都会通过serial0/0 转发出去。

目的地址处于 172.16.64.1 到 172.16.255.254 之间的所有数据包都会通过serial0/0 转发出去。

目的地址处于 172.16.64.1 到 172.16.79.254 之间的所有数据包都会通过serial0/0 转发出去。

目的地址处于 172.16.0.1 到 172.16.64.254 之间的所有数据包都会通过serial0/0 转发出去。

2请参见图示。

管理员正在向网络中添加新路由器。

IP 地址 192.168.13.6/30 已被分配给 R2 上的相连串行接口。

管理员必须为新路由器的串行接口分配什么IP 地址？2192.168.13.4/30192.168.13.5/30192.168.13.7/30192.168.13.58/30192.168.13.61/27192.168.13.63/273OSPF 路由协议身份验证使用 MD5 验证时，下列有关密钥的说法中哪两项正确？（选择两项。

）24密钥以明文形式在路由器之间传递。

密钥用于帮助生成验证用的加密数字。

密钥以加密形式在路由器之间传递。

密钥永远不会在网络上传输。

数据包嗅探器可以捕获密钥。

4请参见图示。

路由表中将显示哪些路由？1R 10.10.4.0/24 [120/1] via 10.10.10.1, 00:00:12, FastEthernet0/1R 10.10.4.0/24 [120/1] via 10.10.20.1, 00:00:12, FastEthernet0/0R 10.10.4.0/24 [120/2] via 10.10.20.1, 00:00:12, FastEthernet0/0R 10.10.4.0/24 [120/3] via 10.10.30.1, 00:00:12, FastEthernet1/0R 10.10.4.0/24 [120/1] via 10.10.30.1, 00:00:12, FastEthernet1/05请参见图示。

ccna章节与期末答案

第一章：正确答案：2.4.5•解析：由于不需要使用网络设备和专用服务器，对等网络易于创建，复杂性更低，且成本更少。

而且对等网络也没有集中管理。

这种网络安全性更低，不可扩展，而且那些同时充当客户端和服务器的设备可能性能更差正确答案：1解析：正确答案： 3.5解析：选择网络介质的条件包括：所选介质可以成功传送信号的距离、要安装所选介质的环境、必须传输的数据量和速度以及介质和安装的成本。

正确答案：3和4解析：终端设备上的应用程序可以生成数据，更改数据内容并且负责启动封装过程。

正确答案：1和4解析：终端设备会发出通过网络传输的数据。

中间设备会在链路发生故障时通过备用路径传输数据，并且会过滤数据传输以增强安全性。

网络介质提供网络消息的传输通道。

正确答案：4解析：外联网是公司外部的人或企业合作伙伴访问数据的网络区域。

内部网只描述通常仅供内部人员访问的网络区域。

当设备连接到有线网络时，有线LAN 会受BYOD（自带设备）影响。

使用大学无线LAN 的设备多为平板电脑和智能手机。

大学生主要使用无线WAN 来访问他们的手机运营商网络。

.正确答案：2解析：由于通过Internet 可以联系在线供应商，所以家庭用户通过Internet 进行网上购物。

内联网基本上是仅供内部使用的局域网。

外联网是外部合作伙伴访问组织内部特定资源的网络。

家庭用户并不一定使用LAN 来访问Internet。

例如，PC 可以通过调制解调器直接连接到ISP。

正确答案：1解析：内部网这个术语用于表示一个组织的私有局域网和广域网连接。

内部网的设计旨在仅允许该组织的成员、员工或其他获得授权的人员进行访问。

正确答案：2和4解析：电缆和DSL 均能实现高带宽、始终联网，并提供到主机计算机或LAN 的以太网连接。

10正确答案：2和3解析：移动电话连接需要使用移动电话网络。

卫星连接通常用于家庭或企业外部不便使用物理布线的位置。

11正确答案：2解析：当对网络资源的请求超出了可用容量时，网络就会变得拥堵。

CCNA思科第三学期ESwitchingExam正确答案

单臂路由器VLAN间路由有哪三项特征？（选择三项。

）需要使用VTP需要使用子接口减少广播域的数量使用过多VLAN时会影响性能需要在路由器和至少一台交换机之间采用接入链路比用于VLAN间路由的其它方法更加经济规定至少要在路由器和交换机之间使用两个交换机端口如果将允许使用中继链路的VLAN范围设置为默认值，表示允许哪些VLAN？仅管理VLAN除扩展范围VLAN之外的所有VLAN除VLAN1和VLAN1002-1005之外的所有VLAN所有的VLAN请参见图示。

哪一个口令可让管理员进入特权执行模式？c isco1c isco2c isco3c isco请参见图示。

假设所有交换机的网桥优先级值都那么哪台交换机将当选为生成树拓扑的根桥？C at-AC at-BC at-CC at-D请参见图示。

最近安装了SW1用于取代集线器。

主机1和主机4同时设备会如何处理此事件？（选择两项。

）当冲突发生时，会调用回退算法。

由于主机1和主机4都连接到交换机，因此不会发生冲突。

交换机将根据交换机MAC地址表中的信息将数据转发到相应的端口。

主机2和主机3会获分配更短的回退值，从而获得访问介质的优先权。

为了防止再发生冲突，交换机会在设定时间内阻塞与主机2、主机3和主机4连接的端口。

请参见图示。

网络管理员需要删除并将属于该VLAN的交换机端口用到一个现有VLAN中。

如果要从S1-Central完全删除VLAN2，同时保证交换机及其所有接口工作正两组命令？（选择两项。

）S1-Central>enable S1-Central#reloadS1-Central>enable S1-Central#eraseflash:S1-Central>enable S1-Central#deleteflash:S1-Central>enable S1-Central#configureterminal S1-Central(config)#novlan2S1-Central>enable S1-Central#configureterminal S1-Central(config-if)#interfacefastethernet0/1S1-Central(config-if)#switch请参见图示。

思科第三学期期末考试答案

请参见图示。

所有中继链路工作正常，而且允许所有VLAN使用所有中继链路。

计算机5 ARP请求。

哪台或哪些设备会收到此消息？仅计算机4* 计算机3和RTR-A计算机4和RTR-A计算机1、计算机2、计算机4和RTR-A计算机1、计算机2、计算机3、计算机4和RTR-A所有计算机和路由器F列关于在接入点上启用开放式身份验证的陈述，哪一项是正确的? *不需要身份验证使用64位加密算法需要使用身份验证服务器需要共同商定的密码VL^N Flane Status Ports1ctefauft active FaOl Fa0/2 FaO/3. Fa0/4 10accounting FaO/5. FaCVG Fa0.7 Fa0/820marking actr/e FaO/5, FaO'10, Fa(V11FaO/12. FaO/U FaO/14 research Faons, FaO/16 FaOH7FaO/16. FaO/19. Fa0/201QQ management adve FaO/21, FaQ/22. FaO'23Fa0/24, GiOJ1, G iO/21002W-default act/unsup1003loken-ring-1 efault act/unsup1004■fddinet-ctefaijlt act/unsup1005act/unsup请参见图示。

该交换机用于让图中所示部门的成员实现连接，但不存在路由。

连接到应该能够与accounting VLAN 中的用户通信。

下列哪项更改可实现所需通信？将该用户连接到GiO/1。

*将该用户连接到FaO/6。

将该用户添加到本征VLAN将该用户添加到默认VLAN分层网络模型具有哪三项优点？（选择三项。

）Opti on 1,36带宽争用现象减少」物理布局范围减小网络的容错能力提高无需配线间」无需第三层功能管理和故障排除工作简化FaO/22 IF列关于新交换机默认配置的说法中哪三项正确？（选择三项。

ccna_第三学期期末考试

1.VLAN 中继有何用途？通过减少广播流量提高网络性能。

选择在交换网络中传输数据的最佳路径。

通过一条链路传送多个VLAN 的流量。

避免交换网络中出现生成树环路。

请参见图示。

两台交换机都配置有默认的网桥优先级。

如果所有链路都在相同的带宽下运行，哪个端口将作为STP 根端口？S1 的Fa0/1 接口S1 的Fa0/2 接口S2 的Fa0/1 接口S2 的Fa0/2 接口请参见图示。

从图中显示的输出可以得到有关STP 的哪两项结论？（选择两项。

）交换机S1 所配置的STP 优先级值在该网络中最低。

交换机S1 被配置为VLAN1 的根桥。

Fa0/21 是交换机S1 的根端口。

Fa0/22 是冗余链路。

Fa0/24 被视为通往根桥的最佳路径。

下列哪种说法正确描述了生成树路径开销？根据环路中连接的交换机总数计算。

根据给定路径上所有交换机的使用率计算。

根据给定路径上交换机的网桥优先级计算。

根据给定路径上每个交换机端口的端口开销值（由端口速度决定）的总和计算。

使用单臂路由器模型配置VLAN 间路由有哪两项要求？（选择两项。

）每个子接口都应配置有自己的IP 地址、子网掩码和唯一的VLAN 分配。

路由器的物理接口必须连接到相邻交换机上的中继链路。

路由器的物理接口数量应该与VLAN 数量匹配。

应该将不同的静态VLAN 分配给路由器的不同接口。

路由器应该配置为VTP 服务器。

请参见图示。

下列哪两项正确描述了图中所示的路由器配置。

（选择两项。

）在路由器上配置路由协议之前，网络192.168.1.0 与网络192.168.3.0 之间无法成功路由。

路由器子接口上未正确配置VLAN。

该配置适用于单臂路由器网络设计。

路由器子接口上未正确配置中继。

应该为接口Fa0/1 分配IP 地址，否则无法进行路由请参见图示。

下列有关交换机S1 配置的说法中哪项正确？端口Fa0/1 和Fa0/3 使用的是Cisco 专有协议。

已使用switchport mode access命令配置交换机的Fa0/1 和Fa0/3 端口。

CCNA第三学期测试题

Which command sequence will enable OSPF in the backbone area for the two Ethernet links on RouterA?RouterA(config)# router ospf 1RouterA(config-router)# network 172.16.4.0 0.0.1.255 area 1RouterA(config)# router ospf 10RouterA(config-router)# network 172.16.4.0 0.0.0.255 area 0RouterA(config-router)# network 172.16.5.0 0.0.0.255 area 0RouterA(config)# router ospf 10RouterA(config-router)# area 0 network 172.16.4.0 0.0.1.255RouterA(config)# router ospf 0RouterA(config-route)# network 172.16.4.0 0.0.255.255 area 0RouterA(config)# router ospf 0RouterA(config-router)# network 172.16.4.0 255.255.255.0RouterA(config-router)# network 172.16.5.0 255.255.255.0RouterA(config)# router ospf 1RouterA(config-router)# network 172.16.4.0 255.255.254.0 area 0How can the OSPF cost for a link be established? (Choose two.)It is set to 1544 by default for all OSPF interfaces.It can be set with the ip ospf cost command.The configured loopback addresses map to link costs.It is calculated proportionally to observed throughput capacity of the router.It may be calculated using the formula 108/bandwidth.Which router command will display the interface priority value and other key information for the OSPF configuration of the serial 0 interface?router# show ospf serial 0router# show interface serial 0 OSPFrouter# show ip interface serial 0router# show ip ospf interface serial 0Because of security concerns, a network administrator wants to set up authentication between two routers. Which of the following commands will configure Router_A to trust Router_B with a clear textRouter_A(config-if)# ospf authentication-key apolloRouter_A(config-if)# ip authentication-key apolloRouter_A(config-if)# ip ospf authentication apolloRouter_A(config-if)# ip ospf authentication-key apolloRouterA, RouterB, and RouterC in the diagram are running OSPF on their Ethernet interfaces. Loopback interfaces (Lo 0) are configured as shown. What happens when RouterD is added to the network?RouterB takes over as DR and RouterD becomes the BDR.RouterD becomes the BDR and RouterA remains the DR.RouterD becomes the DR and RouterA becomes the BDR.RouterC acts as the DR until the election process is complete.RouterD becomes the DR and RouterB remains the BDR.There is no change in the DR or BDR until either current DR or BDR goes down.Refer to the network shown in the diagram. Which command sequence on RouterB will redistribute a Gateway of Last Resort to the other routers in OSPF area 0?RouterB(config)# router ospf 10RouterB(config-router)# gateway-of-last-resort 172.16.6.6RouterB(config)# ip route 0.0.0.0 0.0.0.0 serial 0RouterB(config)# ip route 0.0.0.0 0.0.0.0 172.16.6.6RouterB(config)# router ospf 10RouterB(config-router)# default-information originateRouterB(config)# router ospf 10RouterB(config-router)# default network 172.16.6.6 0.0.0.3 area 0RouterB(config)# ip route 0.0.0.0 0.0.0.0 172.16.6.6RouterB(config)# ip default-route 0.0.0.0 0.0.0.0 172.16.6.6RouterB(config)# router ospf 10RouterB(config-router)# redistribute ip default-routeWhich of the following should be considered when troubleshooting a problem with the establishment of neighbor relationships between OSPF routers? (Choose three.)OSPF interval timers mismatchgateway of last resort not redistributedinterface network type mismatchno loopback interface configuredadministrative distance mismatchinconsistent authentication configurationIn which types of networks are OSPF DR elections necessary? (Choose two.)point-to-pointpoint-to-multipointbroadcast multiaccessnonbroadcast multiaccessWhat does OSPF use to reduce the number of exchanges of routing information in networks where large numbers of neighbors are present? (Choose two.)root routerbackup root routerdomain routerbackup domain routerdesignated routerbackup designated routerWhat information can be obtained from the output of the show ip ospf interface command? (Choose three.)link-state age intervalstimer intervalsrouter ID numberlink-state update intervalsneighbor adjacenciesWhich of the following are required when adding a network to the OSPF routing process configuration? (Choose three.)network addressloopback addressautonomous system numbersubnet maskwildcard maskarea IDWhat speeds up convergence in a network using link-state routing?updates triggered by network changesupdates sent at regular intervalsupdates sent only to directly connected neighborsupdates that include complete routing tablesWhy is it difficult for routing loops to occur in networks that use link-state routing?Each router builds a simple view of the network based on hop count.Routers flood the network with LSAs to discover routing loops.Each router builds a complete and synchronized view of the network.Routers use hold-down timers to prevent routing loops.Which router is the root of an SPF tree?border routernearest neighboring routerlocal routertrunk router, as determined by the SPF algorithmWhich of the following are disadvantages of link-state routing? (Choose three.)Link-state protocols require careful network design.Link-state protocols are prone to routing loops.Link-state hello updates can cause broadcast flooding.Link-state protocols place significant demands on router processors and memory resources.Link-state protocols require a knowledgeable network administrator.Link-state protocols do not support Variable Length Subnet Masking.What are the benefits of the hierarchical design approach that is used in large OSPF networks? (Choose three.)reduction of routing overheadincreased routing overheadfaster convergenceslower convergencedistribution of network instability to all areas of the networkisolation of network instability to one area of the networkA network administrator has configured a default route on Router_A but it is not being shared with adjacent Router_B and the other routers in the OSPF area. Which command will save the administrator the time and trouble of configuring this default route on Router_B and all of the other routers in the OSPF area?Router_A(config-router)# ospf redistribute default-routeRouter_B(config-router)# ospf redistribute default-routeRouter_A(config-router)# default-information originateRouter_B(config-router)# default-information originateRouter_A(config-router)# ip ospf update-defaultRouter_B(config-router)# ip ospf update-defaultWhat does OSPF use to calculate the cost to a destination network?bandwidthbandwidth and hop countbandwidth and reliabilitybandwidth, load, and reliablityWhat will be the result of the DR and BDR elections for this single area OSPF network? (Choose three.)HQ will be DR for 10.4.0.0/16.Router A will be DR for 10.4.0.0/16.HQ will be BDR for 10.4.0.0/16.Router A will be DR for 10.5.0.0/16.Remote will be DR for 10.5.0.0/16.Remote will be BDR for 10.5.0.0/16.The routers in the diagram are configured as shown. The loopback interface on router R1 is labeled as lo0. All OSPF priorities are set to the default except for Ethernet0 of router R2, which has an OSPF priority of 2. What will be the result of the OSPF DR/BDR elections on the 192.1.1.0 network? (Choose two.)R1 will be the DRR1 will be the BDRR2 will be the DRR2 will be the BDRR3 will be the DRR3 will be the BDR。

ccna_第三学期测试第五章答案

ccna_第三学期测试第五章答案请参见图⽰。

该⽹络中所有交换机的MAC 表均为空。

⽽且，该⽹络中的交换机已禁⽤STP。

该⽹络中会如何处理主机PC1 所发送的⼴播帧？交换机SW1 会拦截⼴播并丢弃该帧。

交换机SW1 会将⼴播从除源端⼝之外的所有交换机端⼝转发出去。

这会在⽹络中造成⽆限循环。

交换机SW1 会将⼴播从除源端⼝之外的所有交换机端⼝转发出去。

⽽该⽹络中的所有主机则通过向主机PC1 发送单播帧来回应。

交换机SW1 会将该通信作为单播帧从除源端⼝之外的所有交换机端⼝转发出去。

⽽该⽹络中的所有主机则通过向交换机SW1发送单播帧来回应请参见图⽰。

服务器发送了⼀个ARP 请求，询问其默认⽹关的MAC 地址。

如果未启⽤STP，则此ARP 请求的结果是什么？Router_1 会丢弃该⼴播并使⽤下⼀跳路由器的MAC 地址来回应。

Switch_A 会使⽤Router_1 的E0 接⼝的MAC 地址来回应。

Switch_A 和Switch_B 会将该消息持续泛洪到⽹络中。

该消息会在⽹络中反复传输，直到超出其TTL 为⽌。

在具有⼀个⽣成树实例的已收敛的⽹络中，将存在哪两项要素？（选择两项。

）每个⽹络有⼀个根桥所有⾮指定端⼝转发每个⾮根桥有⼀个根端⼝每个⽹段有多个指定端⼝每个⽹络有⼀个指定端⼝交换机使⽤哪两个条件来选择根桥？（选择两项。

）⽹桥的优先级交换速度端⼝数量基本MAC 地址交换机位置内存⼤⼩交换机通过哪两种⽅式使⽤BPDU 中的信息？（选择两项。

）⽤于在交换机之间协商中继链路⽤于设置冗余链路的双⼯模式⽤于确定到达根桥的最短路径⽤于通过在相连的交换机间共享桥接表来防⽌环路⽤于确定将哪些端⼝作为⽣成树的⼀部分转发帧下列哪两种说法正确描述了⽣成树拓扑中所⽤的BID？（选择两项。

）只有在下级BPDU 被发送出去后，它们才会被根桥发送出去。

它们包含⽹桥优先级和MAC 地址。

只有根桥会发送出BID。

它们被⽣成树拓扑中的交换机⽤来选举根桥。

CCNA期末考试题及答案试卷A(仅供参考)

1.下列有关网络层编址的陈述中哪三项是正确的?（选择三项。

）网络层编址使用分层式结构。

使用长度为48 位的地址。

以太网交换机可以使用它来作出转发决定。

它不支持广播。

其使用的编址方法可以识别地址的网络部分。

网络层编址可以区分每台主机。

2请参见图示。

网络中的所有设备均使用默认配置。

此拓扑中存在多少个广播域？3579113请参见图示。

主机B 已断电。

交换机的MAC 表将发生什么变化？MAC 表不会受影响。

交换机会在Fa0/19 上删除MAC 地址。

交换机会保留MAC 地址，直到主机B 再次通电。

交换机将通过为端口Fa0/19 分配地址FFF.FFFF.FFFF 来重建MAC表。

4.请参见图示。

为了使此网络中的主机接入Internet，路由器RT_A 需要提供哪种功能？地址转换DHCP 服务ftpWeb 服务器5.哪三个地址属于私有IP 地址？（选择三项。

）10.0.0.1127.0.0.1150.0.0.1172.16.0.1192.168.0.1200.100.50.16请参见图示。

电缆1 和电缆2 分别按照特定的物理层要求接线。

表中按编号列出了每个网段以及该网段中用来连接网络组件的电缆。

哪三个网段安装的电缆是正确的？（选择三项。

）网段1网段2网段3网段4网段5网段67.OSI 模型的哪两项功能在第2 层实现？（选择两项）物理编址编码路由布线介质访问控制8.请参见图示。

网络管理员想通过Modem1 从PC1 远程访问路由器的CLI。

要实现此访问，应将路由器的哪一个端口连接到Modem2？控制台端口以太网端口辅助端口串行端口9请参见图示。

某学生对5e 类电缆两端的接线方法如图所示。

结果是什么？（选择两项）电缆无法使用，必须重新接线。

该电缆适合作为全反电缆使用。

该电缆适合作为快速以太网交叉电缆使用。

该电缆适合作为千兆以太网直通电缆使用。

该电缆适合在支持Auto-MDIX 的两台100 Mbps 交换机之间使用。

CCNA_第三学期__期末完整版考试

1CCNA 第三学期期末While monitoring LAN traffic, a network technician notices an excessive number of broadcasts. Which two steps could be included in the processes that are needed to reduce the number of broadcasts onthe network? (Choose two.)Replace any existing hubs with switches.Add a Layer 3 device to route between networks.Subnet the existing IP network to create two networks.Increase the backbone speed by three times the current speed.Add additional switches and spread out the number of hosts evenly between them.2What advantage does cut-through switching provide?It enables QoSIt forwards frames quickly.It provides an analysis of frames.It allows reduction of traffic by using error checking to drop corrupt frames.3Refer to the exhibit. Which switch will be elected as the root bridge of the spanning tree topology?Cat-ACat-BCat-CCat-D4W hich stackable switch feature allows for interconnection of multiple switches and will provide a cost effective solution for networks that require high bandwidth and high availability?modular line cardsspecial backplane portdedicated gigabyte line portsaggregated FastEthernet ports5Refer to the exhibit. This switch is to be added to the production network. Which two facts about VLANs and VTP operation can be confirmed by this output? (Choose two.)The network administrator will be able to configure VLANs of local significance on this switch.VLANs can only be added to the VLAN database on this switch by a VTP advertisement.All VLANs that are configured on this switch will be sent to all other switches in the same VTP domain.This switch will drop all VTP advertisements that come from switches that are configured in the same VTP domain.Adding this switch to the network will cause no disruption in the VTP domain operations if the rest of the switches in the same VTP domain have a higher configuration revision number.6Refer to the exhibit. The hosts connected to switch SW1 are not able to communicate with the hosts in the same VLANs connected to switch SW2. What should be done to fix the problem?Configure VLANs with different VLAN IDs on switch SW2.Reconfigure the trunk port on switch SW2 with static trunk configuration.Introduce a Layer 3 device or a switch with Layer 3 capability in the topology.Apply IP addresses that are in the same subnet to the interfaces used to connect SW1 and SW2.7Refer to the exhibit. A new host needs to be connected to VLAN 3. Which IP address should beassigned to this new host?192.168.1.22 /28192.168.1.31 /28192.168.1.32 /28192.168.1.52 /28192.168.1.63 /288Refer to the exhibit. SW-T has been configured with a single trunking interface. Which VLANs will be allowed across the trunk?Only VLAN 1 will be allowed across the trunk.All configured VLANs will be allowed across the trunk.Only the native VLAN will be allowed across the trunk.Only the the management and native VLANs will be allowed across the trunk.Only VLANs that are configured on the VTP server in the domain will be allowed across the trunk.9Refer to the exhibit. How will switch S2 manage traffic coming from host PC1?S2 will drop the traffic, unless it is management traffic.S2 will tag the frame with VLAN ID 99 when it forwards it over the trunk link.S2 will leave the traffic untagged when it forwards it over a trunk link.S2 will tag the traffic with the highest VLAN ID value when it forwards it over the trunk link. 10Refer to the exhibit. Both switches are interconnected via a trunk link. Host A and host B are on the default VLAN but are not able to exchange traffic. What should be done to fix the problem?Allow all VLANs on the trunk link.Remove the native VLAN from the trunk.Include a router or switch with Layer 3 capabilities.Configure the same native VLAN on both ends of the trunk.11Refer to the exhibit. What does the term DYNAMIC indicate in the output that is shown?This entry can only be removed from the MAC address table by a network administrator.When forwarding a frame to the device with address 0060.5c5b.cd23, the switch does not have to perform a lookup to determine the final destination port.Only the device with MAC address 0060.5c5b.cd23 will be allowed to connect to port Fa0/18.The switch learned this MAC address from the source address in a frame received on Fa0/18.12W hy is MAC address filtering considered a poor choice in securing a WLAN?Available bandwidth is reduced.MAC addresses are easily spoofed.APs are more susceptible to DoS attacks.The payload encryption is easily broken.13How does a switch that is configured for 802.1Q trunking handle untagged frames that are receivedon a trunk port?The frames are dropped.The frames are assigned to the native VLAN.The frames are assigned to the default VLAN.The frames are assigned to the management VLAN.14Refer to the exhibit. Which three options correctly describe the router configuration that is shown?(Choose three.)An IEEE standard trunking protocol is in use.Interface Fa0/1 has been configured with subinterfaces.The shutdown command has been applied to interface Fa0/1.Interface Fa0/1.3 is mapped to the default management VLAN.The configuration is appropriate for a router-on-a-stick network design.An IP address should be applied to interface Fa0/1 for routing to occur.15RSTP is enabled in a switched network that is active and converged. Which switch port type assumesa discarding state on non-root switches?root portedge portalternate portdesignated port16What provides an authentication mechanism for 802.11-based wireless networks?DSSSOFDMSSIDWPA17W hat is the benefit of the auto-MDIX feature on a Cisco Catalyst switch?dynamically assigns a new management VLAN IDautonegotiates IP address information for initial management connectionsallows the use of straight-through patch cables regardless of connected device typesplaces a port immediately in the forwarding state to reduce the time for the spanning tree toreconverge18Refer to the exhibit. VTP pruning is enabled in the VTP domain that is shown. How will switch ST-1 handle Layer 2 broadcast traffic originating from host A on switch ST-C?It will be dropped.It will be forwarded out port Fa0/5 only.It will be forwarded out ports Fa0/5 and Fa0/10.It will be forwarded out ports Fa0/5, Fa0/10, and Fa0/15.19Refer to the exhibit. The network administrator wants to allow both SSH and Telnet connections to Switch1. However, the SSH connections fail. What is the most likely cause of this problem?The RSA key has been removed.SSH has been configured on the wrong line.The transport input command is applied incorrectly.The domain name has been configured in the wrong configuration mode.20Refer to the exhibit. The devices in the network are operational and configured as indicated in the exhibit. However, hosts B and D cannot ping each other. What is the most likely cause of this problem?The link between the switches is up but not trunked.The Fa0/11 interface of Switch1 is not configured as a trunk.Hosts B and D are configured with IP addresses from different subnets.VLAN 20 and VLAN 30 are not allowed on the trunk between the switches.21Refer to the exhibit. Hosts A and B, connected to hub HB1, attempt to transmit a frame at the same time but a collision occurs. Which hosts will receive the collision jamming signal?only hosts A and Bonly hosts A, B, and Conly hosts A, B, C, and Donly hosts A, B, C, and E22 A network administrator implements inter-VLAN routing by configuring subinterfaces on a router.What is one important fact that must be considered?The physical interface must have an IP address configured.The subinterface numbers must match the VLAN ID number.The no shutdown command must be issued on each subinterface.The IP address of each router subinterface must be used as the default gateway for hosts on the corresponding VLAN.23W hat is the purpose of VLAN trunking?It improves network performance by reducing broadcast traffic.It selects the best path to transmit data in a switched network.It carries the traffic of multiple VLANs through a single link.It avoids spanning tree loops in a switched network.24Which parameter is used to uniquely identify one wireless network from another?SSIDOFDMWEPDSSS25W hich layers should support QoS in a hierarchical network?only the distribution and core layersonly the access and distribution layersthe access, distribution, and core layers26Refer to the exhibit. What does "FORWARDING" mean in the command output shown?The switch is sending and receiving data frames.The switch is receiving BPDUs, but not sending data frames.The switch is participating in an election process by forwarding the BPDUs it receives.The switch is receiving BPDUs and populating the MAC address table, but not sending data.27Refer to the exhibit. A network administrator is configuring RT1 for inter-VLAN routing. The switch is configured correctly and is functional. Host1, Host2, and Host3 cannot communicate with each other.Based on the router configuration, what is causing the problem?Interface Fa0/0 is missing IP address configuration information.IP addresses on the subinterfaces are incorrectly matched to the VLANs.Each subinterface of Fa0/0 needs separate no shutdown commands.Routers do not support 892.1Q encapsulation on subinterfaces.28Which switch forwarding method should be used on a network that employs frame classification based on an assigned Quality of Service (QoS) value?cut-throughfast-forwardfragment-freestore-and-forward29Refer to the exhibit. A network administrator has segmented the network into two VLANs. The connected hosts can only access resources in their own VLAN. What is the most scalable and cost effective solution to allow inter-VLAN communication in this network?Replace S1 with a router that has one FastEthernet interface for each PC.Add a second switch and divide the PCs so that each VLAN is connected to its own switch.Configure a router with two subinterfaces on one of its FastEthernet ports and connect it to S1 using a trunk link.Connect a router to a port on S1 and assign the IP address of VLAN1 to the connecting router interface.30Refer to the exhibit. A network administrator issues the show interfaces fastEthernet 0/8switchport command to check the status of the port. What can be concluded from the output?Port Fa0/8 is configured as a trunk with 802.1q encapsulation.Port Fa0/8 is configured as a trunk in VLAN 1.Port Fa0/8 is configured in access mode and associated with VLAN 1.31What will be the effect of the command S1# copy system:running-configtftp://172.16.2.155/tokyo-config?The IOS will be copied to the TFTP server.The configuration file named tokyo-config will overwrite the startup configuration file on S1.The running configuration file on S1 will be saved via TFTP to a file named tokyo-config.The contents of NVRAM on S1 will become the startup configuration file on the tokyo switch.32W hich three statements are correct concerning the default configuration of a new switch? (Choose three.)It is configured in VTP server mode.STP is automatically enabled.The first VTY line is automatically configured to allow remote connections.VLAN1 is configured with a management IP address.All switch ports are assigned to VLAN1.The enable password is configured as cisco.33Refer to the exhibit. What would happen if the network administrator moved the network cable of Host A from interface Fa0/1 to Fa0/3 on switch SW1?Host A remains a member of VLAN 10, because the router is routing traffic between VLANs.Host A is no longer a member of VLAN 10, because port Fa0/3 has been manually assigned to VLAN 30.Host A remains a member of VLAN 10, because the switch provides dynamic VLAN assignment for the port.Host A maintains connectivity to all members of VLAN 10, because it is connected to the same physical network.Host A is no longer a member of VLAN 10, but because port Fa0/3 was unused, it is now amember of VLAN 1.34Refer to the exhibit. Switches S2 and S3 are properly connected using an ethernet cable. A network administrator has configured both switches with VTP, but S3 is unable to propagate VLANs to S2.What could be the reason for this?The VTP configuration revision is different on both switches.The VTP domains are different on both switches.VTP pruning is disabled.VTP v2 is disabled.35Refer to the exhibit. Users A and B are reporting intermittent connectivity problems. Pre-installation surveys showed strong signal strength from the AP locations to the client locations. Outside electricalIncrease the distance between the clients.Change the channel on AP-B to 6 or 11.Place AP-A and AP-B on the same wireless channel.36I n which mode is a VTP switch operating if it does not allow for the creation of local VLANs but it does accept VLAN updates from other switches in the same domain?clientrootservertransparent37Refer to the exhibit. The Layer 2 switching design that is shown has been implemented in a campus environment that is using Spanning Tree Protocol. All inter-switch links that are shown are trunks.Whenever an inter-switch link fails, the network takes nearly a minute to completely converge. How can the convergence time be reduced?Increase the capacity of the distribution and core trunk links to 10 Gb/s.Use Layer 3 switching on the core switch.Implement Rapid Spanning Tree Protocol.38Refer to the exhibit. Router R1 is properly configured for router on a stick inter-VLAN routing, but PC1 is unable to ping PC2. What needs to be done to resolve the problem?Rename VLAN1.Connect one more port of S1 to R1.Configure the Fa0/1 port of S1 as a trunk port.Move the Fa0/0 interface of R1 to another VLAN.39What is a result of improperly implementing a network with redundancy at Layer 2?an increase of unicast and multicast errors at Layer 3a decrease in the amount of broadcast trafficend device malfunction because of broadcast storms40W hy is it important that the network administrator consider the spanning-tree network diameter when choosing the root bridge?The network diameter limitation is 9.BPDUs may be discarded because of expiring timers.The cabling distance between the switches is 100 meters.The network diameter must be set to the number of meters of the cable between the root bridge and its farthest connected switch.41Refer to the exhibit. A network administrator needs to add IP phones to the network. To whichdevices should the IP phones connect?AS1 and AS2DS1 and DS2DS1, DS2, and CS1AS1, AS2, DS1, and DS242Which device or devices should have the Spanning Tree Protocol enabled to prevent host traffic from creating a broadcast storm?Core_S1Access_S2 and Access_S3Core_S1, Access_S2, and Access_S3Core_S1, Access_S2, Access_S3, and R143Refer to the exhibit. All edge ports are configured with the spanning-tree portfast command. Host1 is recently connected to port Fa0/1 on switch SW1 . Which statement is true about the status of port Fa0/1?The port will transition into blocking state.The port will transition immediately into forwarding state.The port will transition into blocking state and then immediately into forwarding state.The port will transition into blocking state and immediately transition through the listening and learning states.44A network administrator enables sticky learning on all access mode interfaces of a Catalyst switch, saves the configuration, then connects hosts to the switch. After the switch operates for several days, the administrator reboots the switch without saving the running configuration. What is the result?All previously learned MAC addresses are lost.The switch reverts to non-sticky dynamic learning.Connected hosts are no longer able to communicate with the switch.Previously learned sticky addresses are retained in the switch configuration.45The network administrator wants to configure a switch to pass VLAN update information to other switches in the domain but not update its own local VLAN database. Which two steps should the administrator perform to achieve this? (Choose two.)Reset the VTP counters.Configure VTP version 1 on the switch.Configure the VTP mode of the switch to transparent.Verify that the switch has a higher configuration revision number.Configure the switch with the same VTP domain name as other switches in the network.46Which statement regarding the service password-encryption command is true?The service password-encryption command is entered at the privileged EXEC mode prompt.The service password-encryption command encrypts only passwords for the console and VTY ports.The service password-encryption command encrypts all previously unencrypted passwords in the running configuration.To see the passwords encrypted by the service password-encryption command, enter the no service password-encryption command.47Refer to the exhibit. The network consists of four hubs and a switch. The hosts connected to each hub are assigned addresses in the respective VLAN as shown. PC1 on VLAN 1 becomes infected with a virus and initiates a continuous IP broadcast. Which hubs will receive the broadcasts?Hub AHubs A and BHubs A and CHubs A, B, C, and D48 A wireless LAN access point will convert traffic between which two frame encapsulation types?802.1 and 802.11802.3 and 802.11802.3 and 802.16802.5 and 802.1649I n the implementation of PVST+ in a specific VLAN where all switches have default spanning tree priorities, which spanning-tree command setting could be assigned to force one of the Catalyst switches to become and remain the root bridge?root primarypriority 8192priority 2048spanning-tree mode rapid pvst50Refer to the exhibit. The teacher host is connected to port Fa0/7 on switch STW. A student hasdecided to share access to the Internet by attaching a hub and laptop to STW as shown. What will be the result of the student making this connection?The Fa0/7 port of STW will be shutdown.The student will gain full access to the Internet.Both the teacher and student will be able to receive data but only the teacher will be able to send.The frames from the laptop will be dropped, but the teacher host will maintain connectivity with the network.51Refer to the exhibit. Switch SW2 was tested in a lab environment and then inserted into a production network without reloading its configuration. After the trunk link between SW1 and SW2 was brought up, all users lost connectivity to the network. What could be the source of the problem?All the VLANs were pruned from the trunk port between SW1 and SW2.SW1 and SW2 cannot be both set as VTP servers in the same VTP domain.VTP configuration revision number of SW2 was higher than the configuration revision number of SW1.The additional VLANs from SW2 created more VLANs than the VLAN database of SW1 could contain.。

ccna第三学期1-7套练习题答案(最新)

ESwitching Chapter 1 - CCNA Exploration: LAN 交换和无线(版本4.0)1、分层网络设计模型中的哪一层称为互连网络的高速主干层，其中高可用性和冗余性是该层的关键？A.接入层B. 核心层C. 数据链路层D. 分布层E. 网络层F. 物理层2、分层网络设计模型中的哪一层提供了将设备接入网络的途径并控制允许那些设备通过网络进行通信？A. 应用层B. 接入层C. 分布层D. 网络层E. 核心层3、分层设计模型中的哪一层使用策略来控制网络流量的流动并通过在虚拟局域网 (VLAN) 之间执行路由功能来划定广播域的边界？A. 应用层B. 接入层C. 分布层D. 网络层E. 核心层4、从传统的公司网络架构迁移到完全融合网络后，很可能产生什么影响？A. 可将本地模拟电话服务完全外包给收费更低的提供商B. 以太网 VLAN 结构会简化C. 会形成共享的基础架构，因此只需管理一个网络。

D. QoS 问题会大大减轻5、语音数据流和视频数据流争夺带宽的问题会减轻。

应该在分层网络的哪一层或哪几层实现链路聚合?A. 仅核心层B. 分布层和核心层C. 接入层和分布层D. 接入层、分布层和核心层6、下列哪种说法正确描述了模块化交换机？A. 外形纤细B. 允许通过冗余背板进行交换机互连C. 物理特性固定D. 特性灵活多变7、下列哪项功能可在交换网络中通过合并多个交换机端口来支持更高的吞吐量？A. 收敛B. 冗余链路C. 链路聚合D. 网络直径8、在处于不同的 VLAN 中的设备间配置通信需要使用 OSI 模型中的哪个层？A. 第 1 层B. 第 3 层C. 第 4 层D. 第 5 层9、企业级交换机有哪两项特点？（选择两项。

）A. 端口密度低B. 转发速度高C. 延时水平高D. 支持链路聚合E.端口数量预先确定10、Cisco 三层式分层模型中的三层都支持哪两项功能？（选择两项。

）A. 以太网供电B. 在冗余中继链路之间进行负载均衡C. 冗余组件D. 服务质量E. 链路聚合11、网络管理员选择的交换机将在网络核心层工作。

CCNA期末考试答案(网络安全技术练习题)

1. 半连接攻击属于（）A．溢出攻击 B.嗅探攻击 C. 注入攻击 D.拒绝服务攻击2. TCP三次握手中用到的标志位是（）A. FINB. SYNC. RSTD. PSH3. 下列关于对称加密算法和非对称加密算法的说法中正确的是（）A.对称加密速度较慢B.对称加密可以实现数据的不可否认性C.非对称加密速度较慢D.非对称加密的密文是紧凑的4 以下不支持认证功能的路由协议是（）A. EIGRPB. Ripv1C.ospfD. Ripv25. 以下哪一项不属于保护路由器的有效方法（）A.开启日志服务并建立日志服务器B. 部署NTP服务器实现时钟同步C.关闭路由器上的CDP服务D. 启用端口安全6.以下关于SSH的说法正确的是（）A.SSH采用对称加密算法B.SSH未对数据加密C.SSH采用非对称加密算法D.SSH一般用于内网发起的管理行为7. AAA不包含哪一层含义（）A.认证B.过滤C.授权D.记账8.以下哪一项是思科的私有协议（）A.radiusB.802.1qC.tacacs+D.ipsec9.通过访问控制列表防范分片攻击需要在语句后加关键字（）A.establishedB.fragmentC.logD.reflect10.以下哪一项是基于异常的IDS监测模式的缺点（）A.不能抵御新型攻击B.特征库更新速度制约使用效果C.不会错报D.容易错报漏报11. 以下关于IDS与IPS说法正确的是( )A. IDS一般部署在网络出口主干链路上B.IDS能够阻断发现的攻击行为C. IPS一般根据特征库来检测攻击行为D.IPS不能阻断发现的攻击行为12. 以下不能起到防火墙作用的技术是（）A.IDSB.ACLC.NATD.代理服务器13.以下关于MD5的说法正确的是( )A.md5是一种加密算法B.md5用于保障数据的机密性C.md5是可逆的D.md5用于保障数据的完整性14. 为恢复路由器登录密码，需把寄存器值改为（）。

cisco第三学期模拟期末考试

∙考试结果∙试题反馈报告CCNA Exploration: LAN 交换和无线 (版本 4.0) -ESwitching Practice Final Exam下面是针对您未获得满分的题目的反馈。

有些互动题目可能不会显示您的回答。

分项分数：1请参见图示。

所有中继链路工作正常有 VLAN 使用所有中继链路。

计算机 5 发送了一条 ARP 请求。

哪台或哪些设备会收正确响应您的响应仅计算机 4计算机 3 和 RTR-A计算机 4 和 RTR-A计算机 1、计算机 2、计算机 4 和 RTR-A计算机 1、计算机 2、计算机 3、计算机 4 和 RTR-A所有计算机和路由器此试题参考以下领域的内容：CCNA Exploration: LAN 交换和无线∙ 3.1.4 通过 VLAN 控制广播域2 下列关于在接入点上启用开放式身份验证的陈述，哪一项是正确的？正确响应您的响应不需要身份验证使用 64 位加密算法需要使用身份验证服务器需要共同商定的密码此试题参考以下领域的内容：CCNA Exploration: LAN 交换和无线∙7.2.2 无线安全协议3请参见图示。

该交换所示部门的成员实现连接，但不存在路由。

连接到 Fa0/22 的一位用户应该能够与 a VLAN 中的用户通信。

下列哪项更改可实现所需通信？正确响应您的响应将该用户连接到 Gi0/1。

将该用户连接到 Fa0/6。

将该用户添加到本征 VLAN。

将该用户添加到默认 VLAN。

此试题参考以下领域的内容：CCNA Exploration: LAN 交换和无线∙ 3.3.3 管理 VLAN4 分层网络模型具有哪三项优点？（选择三项。

）正确您的此试题参考以下领域的内容：CCNA Exploration: LAN 交换和无线∙ 1.1.2 分层网络设计的原则5 下列关于新交换机默认配置的说法中哪三项正确？（选择三项。

）正确您的此试题参考以下领域的内容：CCNA Exploration: LAN 交换和无线∙ 3.3.2 配置 VLAN6请参见图示。

CCNA3 final 中文

2可向可从可向可向可向可从4可采用哪两种方法删除交换机的关闭交换机电源并再次打开以清除所有动态获知的地址。

可采用可采用可采用在交换机端口不活动达6810分层网络设计模型具有哪三项优点？13需要配置下列哪三项才能允许用户通过默认网关vty控制台线路口令HTTP管理用于连接的以太网端口的双工和速度设置应该为所使用的是标准化中继协议。

已经在接口该配置适用于单臂路由器网络设计。

接口接口15下列关于1719在在在在此开销代表从一台上游（更接近根交换机）交换机的端口Switch4Switch4根交换机通告的开销值是2325可在S1 2729如果将会创建一个新的交换机默认为仅允许交换机不再能作为交换机仅在生成新的接入点数据服务器客户端RADIUS33下列哪两种说法正确地描述了生成树协议？它只能用于采用路由器的网络中。

35下列关于新交换机默认配置的说法中哪三项正确？37网络管理员接到为大型企业级交换网络选择硬件的任务。

39为什么网络管理员在选择根桥时必须考虑生成树网络直径？SSHSSHtransport input 不能同时配置434547下列哪种方法可用于与无线接入点建立管理连接？49S1S3S4S4S2S1当前仅将一个目前尚无法进行接口图中所示的接口处于关闭状态。

思科CCNA第三学期期末考试完整版

参加考试-ESwitchingFinalExam-CCNAExploration:LAN交换和无线(版本4.0)以下哪项参数用于唯一标识一个无线网络，使其与其它网络区分开来？SSIDOFDMWEPDSSS分层网络模型具有哪三项优点？（选择三项。

）带宽争用现象减少物理布局范围减小网络的容错能力提高无需配线间无需第三层功能管理和故障排除工作简化在将Catalyst交换机迁移到其它VTP管理域之前，应该进行哪三项任务？（项。

）选择正确的VTP模式和版本。

使用新管理域的名称配置交换机。

从新域中的VTP服务器上下载VTP数据库。

配置新域内的VTP服务器，使其识别该交换机的BID。

重置VTP计数器，使交换机可与新域内的其它交换机同步。

检验交换机的配置修订版号是否比新域内的其它交换机的低。

下列哪两种说法正确地描述了生成树协议？（选择两项。

）它只在第2层使用。

它在交换机上配置。

它消除了网络拓扑中的第2层环路。

它限制了端口上所允许的有效MAC地址的数量。

它使VLAN信息得以传播到网络中的其它交换机。

下列哪种方法可建立用于配置LinksysWRT300N无线接入点的管理连接？与接入点关联，然后与接入点建立超级终端会话。

以物理方式连接到接入点，然后重新启动计算机以启动配置软件。

在接入点所在的IP子网内的计算机上的web浏览器中输入接入点的默认址。

修改与接入点连接的计算机的TCP/IP属性，使其与接入点处于同一个然后重新启动计算机以建立连接。

请参见图示。

源地址并非0019.d2e4.d9f7的帧进入接口Fa0/24时会发生什么Fa0/24会变为error-disabled（错误-禁用）状态。

传入帧会被丢弃。

Fa0/24端口LED会关闭。

安全违规计数会增加。

可采用哪两种方法删除交换机的MAC地址表中的条目？（选择两项。

）关闭交换机电源并再次打开以清除所有动态获知的地址。

可采用clearswitching-tables命令删除静态配置的条目。

思科 ccna第三册final试题及答案

思科第三册final 试题及答案1请参见图示。

下列哪三种说法描述了 Host1 和 Host2 无法通信的原因？（选择三项。

）交换机端口处于不同的 VLAN 中。

交换机的 IP 地址在错误的子网中。

主机被配置在不同的逻辑网络中。

需要路由器在 Host1 与 Host2 之间转发流量。

每个 VLAN 中的 VLAN 端口必须连续分配。

主机的默认网关地址必须处于同一个逻辑网络中。

2请参见图示。

主机 PC_A 和主机 PC_B 同时发送流量，来自这两台发送站的帧发生了冲突。

最突信号的是哪台设备？集线器 HB1交换机 SW1路由器 R1交换机 SW2路由器 R2交换机 SW43请参见图示。

在生成树协议中，“学习”表示什么意思？交换机正在发送并接收数据帧。

交换机并未接收 BPDU，但正在发送并接收数据。

交换机正在通过转发收到的 BPDU 参与选举过程。

交换机正在接收 BPDU 并填充 MAC 地址表，但并未发送数据。

4请参见图示。

RTB 被配置为进行传统的 VLAN 间路由。

RTB 可以 ping 通计算机 A 但无法 pin 机 B。

此故障的原因可能是什么？Fa0/11 端口处于错误的 VLAN 中。

RTB 上没有有效的路由协议。

计算机 B 的 IP 地址在错误的逻辑网络中。

路由器的 Fa0/1 接口上配置了错误的中继封装类型。

5请参见图示。

网络管理员已将网络划分为两个 VLAN，R1 和 S1 的配置如图所示。

但是，PC1 无法问题很可能出在哪里？R1 上未配置路由协议。

S1 的 Fa0/1 端口不是中继端口。

S1 上未设置默认网关地址。

S1 和 R1 之间只配置了一条物理链路用于 VLAN 间路由。

6单臂路由器 VLAN 间路由有哪三项特征？（选择三项。

）需要使用 VTP需要使用子接口减少广播域的数量使用过多 VLAN 时会影响性能需要在路由器和至少一台交换机之间采用接入链路比用于 VLAN 间路由的其它方法更加经济规定至少要在路由器和交换机之间使用两个交换机端口7请参见图示。