125-1131-403;125-1191-403;中文规格书,Datasheet资料

合集下载

NPort 6150 6250 Series Quick Installation Guide

P/N: 1802061500016 *1802061500016*NPort 6150/6250 Series Quick Installation GuideEdition 9.0, November 2016Technical Support Contact Information/supportMoxa Americas:Toll-free: 1-888-669-2872 Tel: 1-714-528-6777 Fax: 1-714-528-6778 Moxa China (Shanghai office): Toll-free: 800-820-5036 Tel: +86-21-5258-9955 Fax: +86-21-5258-5505 Moxa Europe:Tel: +49-89-3 70 03 99-0 Fax: +49-89-3 70 03 99-99 Moxa Asia-Pacific:Tel: +886-2-8919-1230 Fax: +886-2-8919-1231 Moxa India:Tel: +91-80-4172-9088 Fax: +91-80-4132-10452016 Moxa Inc. All rights reserved.OverviewThe NPort 6150/6250 series secure serial device servers provide reliable serial-to-Ethernet connectivity for a wide range of serial devices. The NPort 6150/6250 support TCP Server, TCP Client, UDP, andPair-Connection operation modes to ensure the compatibility of network software. In addition, the NPort 6150/6250 also support Secure TCP Server, Secure TCP Client, Secure Pair-Connection, and Secure Real COM modes for security critical applications such as banking, telecom, access control, and remote site management.Package ChecklistBefore installing a NPort 6150/6250 secure device server, verify that the package contains the following items:• 1 NPort 6150 or NPort 6250•Power adapter (does not apply to -T models)• 2 wallmount ears•Documentation and software CD•Quick installation guide (this guide)•Warranty cardOptional Accessories•DK-35A: DIN-rail mounting kit (35 mm)•DIN-rail power supply•CBL-RJ45M9-150: 8-pin RJ45 to male DB9 cable•CBL-RJ45M25-150: 8-pin RJ45 to male DB25 cableNOTE: Please notify your sales representative if any of the above items are missing or damaged.Hardware IntroductionNPort 6150NPort 6250Reset Button—Press the Reset Button continuously for 5 sec to load factory defaults. Use a pointed object, such as a straightened paper clip or toothpick, to press the reset button. This will cause the Ready LED to blink on and off. The factory defaults will be loaded once the Ready LED stops blinking (after about 5 seconds). At this point, you should release the reset button.LED IndicatorsAdjustable pull high/low resistor for RS-422/485 (150 K Ω or 1 K Ω)Jumpers are used to set the pull high/low resistors. The default is 150 kΩ. Short the jumpers to set this value to 1 kΩ. Do not use the 1 kΩ setting with RS -232 mode, since doing so will degrade the RS-232 signals and shorten the communication distance.Hardware Installation ProcedureSTEP 1: Connect the 12-48 VDC power adaptor to the NPort 6150 andthen plug the power adaptor into a DC outlet.STEP 2: For first-time configuration, use a cross-over Ethernet cable toconnect the NPort 6150 directly to your computer’s Ethernet cable. For connecting to a network, use a standardstraight-through Ethernet cable to connect to a hub or switch.STEP 3: Connect the NPort 6150’s serial port to a serial device.Placement OptionsThe NPort 6150/6250 can be placed flat on a desktop or other horizontal surface. In addition, you may use the DIN-rail or wallmount options, as illustrated below.WallmountDin RailSoftware Installation InformationThe Documentation and software CD contains the user’s manual, NPort Search Utility, and the PComm Lite Suite. Insert the CD into yourcomputer’s CD-ROM drive and follow the on-screen instructions. Please refer to the user’s manual for additional details on using the NPort Search Utility and PComm Lite.Pin Assignments and Cable WiringTwo serial cables for connecting the NPort 6150 to a serial device can be purchased separately. The wiring diagrams for the two cables are shown below.。

KSZ8851-16MLL DEMO BOARD 48-PIN ETHERNET CONTROLLE

SD13
SD7 40
CPU_D14 3
6
SD14
SD8 39
CPU_D15 4
5
SD15
SD9 36
SD10 35
33
SD11 34
CPU_CMD
33
SD12 33
R10
SD13 32
CPU_CSN
33
SD14 31
R12
SD15 30
CPU_WRN
33
CMD
11
R14
CPU_RDN
33
CSN
12
R16
5 6 7 8
TANT
C27
R28 10uF
470pF 2.49K
Power 3.3V 0.1uF (red LED)
CSN CMD
4.7K R27 4.7K R29
GBLC03C_0 D3
GND 2 GND
VR 5 3.3VA
INTRN 4.7K R30
VOUT = 1.24 X [ 1 + ( 2.49k/ 1.5K ) ]
5
4
3
KSZ8851-16MLL (48-pin) Demo Board Black Diagram
D
Headers 20x2
RJ45
LAN1 T
KSZ8851-16MLL
Reset
Power
+1.8V
+2.5V
+3.3V
STATUS LEDs
OSC
EEPROM
C
MIC5209YM
25 MHz
AT93C46
x2
2
1
DATE:

超米特电子有限公司产品说明书

1US Headquarters TEL +(1) 781-935-4850FAX +(1) 781-933-4318 • Europe TEL +(44) 1628 404000FAX +(44) 1628 404090Asia Pacific TEL +(852) 2 428 8008FAX +(852) 2 423 8253South America TEL +(55) 11 3917 1099FAX +(55) 11 3917 0817Superior elongation and tensilestrength help to prevent tearing in use due to mishandling. Typical properties for CHO-SEAL 1310 and 1273 materi-al are shown on pages 33 and 32respectively.High Shielding PerformanceCHO-SEAL 1310 material provides more than 80 dB of shielding effectiv-ness from 100 MHz to 10 GHz, while CHO-SEAL 1273 material provides more than 100 dB.Low Volume ResistivityBoth materials have exceptionally low volume resistivity, which makes them well suited for grounding appli-cations in which a flexible electrical contact is needed.Low Compression GasketSpacer gaskets are typicallydesigned to function under low deflec-tion forces. Chomerics uses design tools such as Finite Element Analysis (FEA) to accurately predict compres-sion-deflection behavior of various cross section options. Refer to page16.LCP Plastic SpacerLiquid crystal polymer (LCP)spacers, including those made with Vectra A130 material, provide aCHO-SEAL ®1310 or 1273Conductive ElastomersWith EMI spacer gaskets, shielding and grounding are provided by Chomerics’CHO-SEAL 1310 and 1273 conductive elastomers, specifi-cally formulated for custom shape molded parts. They provide excellent shielding and isolation against electro-magnetic interference (EMI), or act as a low impedance ground path between PCB traces and shielding media. Physically tough, these elas-tomers minimize the risk of gasket damage, in contrast to thin-walled extrusions or unsupported molded gaskets.Silicone-based CHO-SEAL 1310and 1273 materials offer excellent resistance to compression set over a wide temperature range, resulting in years of continuous service. CHO-SEAL 1310 material is filled with silver-plated-glass particles, while 1273 utilizes silver-plated-copper filler to provide higher levels of EMI shielding effectiveness.EMI Spacer GasketsThe unique design of Chomerics’EMI spacer gaskets features a thin plastic retainer frame onto which a conductive elastomer is molded. The elastomer can be located inside or outside the retainer frame, as well as on its top and bottom surface. EMI spacer gaskets provide a newapproach to designing EMI gaskets into handheld electronics such as dig-ital cellular phones. Board-to-board spacing is custom designed to fit broad application needs. Customized cross sections and spacer shapes allow for very low closure forcerequirements and a perfect fit in any design or device.Robotic InstallationSpacer gaskets can be installed quickly by robotic application. Integral locater pins in the plastic spacer help ensure accuratepositioning in both manual and pick-and-place assembly. Benefits include faster assembly and lower labor costs.The integrated conductive elastomer/plastic spacer gasket is a low cost,easily installed system for providing EMI shielding and grounding in small electronic enclosures.Figure 1Single Piece EMI Gasket/Locator PinsCHO-SEAL 1310 or 1273 Conductive Elastomer (Inside)Plastic Spacer Around Outsideor InsideApplications for EMI Spacer GasketsThe spacer gasket concept is especially suited to digital and dual board telephone handsets or other handheld electronic devices. It provides a low impedance path between peripheral ground traces on printed circuit boards and components such as:•the conductive coating on a plastic housing•another printed circuit board •the keypad assemblyTypical applications for EMI spacer gaskets include:•Digital cellular, handyphone and personal communications services (PCS) handsets •PCMCIA cards•Global Positioning Systems (GPS)•Radio receivers•Other handheld electronics, e.g.,personal digital assistants (PDAs)•Replacements for metal EMI shield-ing “fences” on printedcircuit boards in wireless tele-communications devicesstable platform for direct, highprecision molding of conductive elas-tomers. The Vectra A130 material described in Table 1 has excellent heat deflection temperature character-istics (489°F, 254°C). For weight con-siderations, the LCP has aspecific gravity of only 1.61. This plas-tic is also 100% recyclable.Typical EMI Spacer Gasket Design ParametersThe EMI spacer gasket concept can be considered using the design parameters shown in Table 2. Some typical spacer gasket profiles are shown below.Figure 2Typical Spacer Gasket Profiles3US Headquarters TEL +(1) 781-935-4850FAX +(1) 781-933-4318 • Europe TEL +(44) 1628 404000FAX +(44) 1628 404090Asia Pacific TEL +(852) 2 428 8008FAX +(852) 2 423 8253South America TEL +(55) 11 3917 1099FAX +(55) 11 3917 0817Finite Element AnalysisChomerics, a division of the Parker Hannifin Corporation’s Seal Group, is the headquarters of Parker Seal’s Elastomer Simulation Group. This unit specializes in elastomer finite element analysis (FEA) using MARC K6 series software as a foundation for FEA capability.Benefits of FEA include:•Quickly optimizing elastomer gasket designs•Allowing accurate predictions of alternate elastomer design concepts •Eliminating extensive trial and error prototype evaluationTypical use of FEA in EMI spacer gasket designs is to evaluate the force vs. deflection requirements of alternate designs.For example, onespacer design features a continuous bead of con-ductive elastomer molded onto a plastic spacer. An alternative designemploys an “interrupted bead,” where the interrup-tions (gaps left on the plastic frame) are sized to maintain the requiredlevel of EMI shielding. Figure 4illustrates these alternative designs.Gasket DeflectionFigure 5 compares the effect of continuous and interrupted elastomer gasket designs in terms of the force required to deflect the conductive elastomer. This actual cellular handset application required a spacer gasket with interrupted bead to meet desired deflection forces.Chomerics Designand Application ServicesChomerics will custom design a spacer for your application. Advice,analysis and design assistance will be provided by Chomerics Applications and Design engineers at no additional fee. Contact Chomerics directlyat the locations listed at the bottom of the page.Figure 3FEA Example of an EMISpacer Gasket Cross SectionFigure 4Continuous (top) and InterruptedElastomer GasketsFigure 5Typical Spacer Gasket Deflection。

SCALANCE X101-1 商品说明书

24 V
6GK5101-1BB00-2AA3 Page 1/4
06/28/2018
Subject to change without notice © Copyright Siemens
● at DC / maximum
Supply voltage, current consumption, power loss Supply voltage ● external ● external Type of voltage / of the supply voltage Product component / fusing at power supply input Fuse protection type / at input for supply voltage Consumed current ● maximum Power loss [W] ● at DC / at 24 V
Compact 40 mm 125 mm 124 mm 0.55 kg
Yes Yes Yes
No No
FM3611: Class 1, Divison 2, Group A, B, C, D / T.., Class 1, Zone 2, Group IIC, T.. EN 600079-15 II 3 G EEx nA II T.. KEMA 06 ATEX 0021 X
Yes
Yes Yes Yes Yes Yes No 134 y
/snst
/simatic-net https:// /industry/infocenter /bilddb /cax https://
Security information
UL 60950-1, CSA C22.2 No. 60950-1 UL 1604 and UL 2279-15 (Hazardous Location), Class 1 / Division 2 / Group A, B, C, D / T.., Class 1 / Zone 2 / Group IIC / T.. EN 61000-6-3 EN 61000-6-4:2001 EN 61000-6-2:2001, EN 61000-6-4:2001 Yes Yes Yes

PCS-9705_X_说明书_国内中文_国内标准版_X_R1.03_(ZL_CKZZ5305.1108)

ii
南京南瑞继保电气有限公司
目录
PCS-9705 系列系列测控装置
前言.................................................................................................................................................... i 目录.................................................................................................................................................. iii 第 1 章概述...................................................................................................................................... 1
额定值在接入交流电压电流回路或直流电源回路时，请确认他们符合装置的额定参数。
印刷电路板在装置带电时，不允许插入或拔出印刷电路板，否则可能导致装置不正确动作。
外部回路当把装置输出的接点连接到外部回路时，须仔细检查所用的外部电源电压，以防止所连接的回
路过热。连接电缆
仔细处理连接的电缆避免施加过大的外力。
南京南瑞继保电气有限公司
i
PCS-9705 系列系列测控装置
警告！
曝露端子在装置带电时不要触碰曝露的端子等，因为可能会产生危险的高电压。
残余电压在装置电源关闭后，直流回路中仍然可能存在危险的电压。这些电压需在数秒钟后才会消失。

海康威视总线制报警主机操作手册

第 3 章系统启动.........................................................................................................................20
3.1 总线式网络报警主机启动 ...................................................................................................... 20 3.2 报警键盘启动 .......................................................................................................................... 20 3.3 键盘编址 .................................................................................................................................. 20 3.4 出厂设置 .................................................................................................................................. 21
工作状态指示灯网络状态指示灯电源指示灯
GPRS模块
SIM卡槽
D+ D- +12V G
COM1
COM2
COM3
COM4

泌乳素放射免疫分析药盒说明书资料精

【仪器】
γ－计数器低温离心机恒温水浴箱
【样本收集和保存】
220 微升人血清样本。采静脉血 5ml 于塑料试管中，静置使其凝固后，1500 转／分离心，取其上清液，放置玻璃瓶中。如果样本不立即使用，可在-18℃~-25℃储存 6 个月。严重溶血、高浓度的脂类、胆红素对测定结果有影响。
【使用前准备】
试验前，恢复样本至室温，小心摇匀血清样本。【实验方法】
【实验方法 I 】
1、将实验所需试剂及样本放置室温，平衡至少 30 分钟以上才可进行操作； 2、取 60X12mm 聚苯乙烯管进行编号，所有实验均做双管重复； 3、取每个浓度的标准品、质控血清和样本 200µl 加入相应编号的试管中； 4、每管均各加入 200µl 标记物工作液； 5、除去总 T 管、NSB 管以外的每管均各加入 200µl 抗体工作液，充分混匀； 6、37℃温育 180 分钟； 7、每管均各加入 500µl 分离剂后，充分混匀； 8、室温放置 5~10 分钟后，离心 3500 转／分，20 分钟后，吸去或倾倒掉上清液； 9、用 γ-计数器测定各管计数 CPM. 推荐检测时间: 1 分钟 10、从标准曲线上读取样本及质控血清的浓度。
【试剂主要组成成分】
PRL 标准品：
一套共 7 瓶，以不含 PRL 的人血清为基质，用时轻轻摇匀，（2~8 ℃）需冷存。
PRL 标准品浓度
G
（单
A
B
C
D
E
F
位）0Biblioteka 51025
50
100
200
ng/ml
本药盒标准品浓度采用 WHO 1st IRP75/504,与 WHO2nd IS83/562 的换算关系为： 1ng/ml(1st IRP)=21mIU/ml(2nd IS83/562) 质控血清：两瓶，低值和高值，1.0 ml／瓶，浓度值范围见瓶上标签。2～8℃冷存。抗 PRL 抗体：一瓶，绿色溶液，2～8℃冷存。 125I-PRL：一瓶，< 88.23 kBq/瓶，红色溶液，2～8℃冷存。分离剂：一瓶，蓝色溶液，充分摇匀后使用，2～8℃冷存。

安信可 Ra-01SH 规格书说明书

文档“按现状”提供，不负任何担保责任，包括对适销性、适用于特定用途或非侵权性的任何担保，和任何提案、规格或样品在他处提到的任何担保。

本文档不负任何责任，包括使用本文档内信息产生的侵犯任何专利权行为的责任。

本文档在此未以禁止反言或其他方式授予任何知识产权使用许可，不管是明示许可还是暗示许可。

文中所得测试数据均为安信可实验室测试所得，实际结果可能略有差异。

文中提到的所有商标名称、商标和注册商标均属其各自所有者的财产，特此声明。

最终解释权归深圳市安信可科技有限公司所有。

注意由于产品版本升级或其他原因，本手册内容有可能变更。

深圳市安信可科技有限公司保留在没有任何通知或者提示的情况下对本手册的内容进行修改的权利。

本手册仅作为使用指导，深圳市安信可科技有限公司尽全力在本手册中提供准确的信息，但是深圳市安信可科技有限公司并不确保手册内容完全没有错误，本手册中的所有陈述、信息和建议也不构成任何明示或暗示的担保。

文件制定/修订/废止履历表版本日期制定/修订内容制定核准V1.02020.8.12首版徐V1.12020.8.19更新部分参数徐目录一、产品概述 (5)二、电气参数 (7)三、外观尺寸 (9)四、管脚定义 (10)五、原理图 (11)六、设计指导 (12)七、回流焊曲线图 (14)八、包装信息 (15)九、联系我们 (15)一、产品概述安信可LoRa系列模块（Ra-01SH）由安信可科技设计开发。

该模组用于超长距离扩频通信，其射频芯片SX1262主要采用LoRa™远程调制解调器，用于超长距离扩频通信，抗干扰性强，能够最大限度降低电流消耗。

借助SEMTECH的LoRa™专利调制技术，SX1262具有超过-148dBm的高灵敏度，+22dBm的功率输出，传输距离远，可靠性高。

SHG01.103商品说明书

DataOrdering dataProduct type descriptionSHG01.103Article number (order number)101009662EAN (European Article Number)4030661520971eCl@ss number, Version 9.027-27-26-02eCl@ss number, Version 11.027-27-26-02Approval - StandardsCertificates cULusCCC CNCAGeneral dataProduct nameSHG StandardsBG-GS-ET-15 EN 60947-5-1 EN ISO 14119 Enclosure materialAluminium Enclosure coating materialpainted Material of the contacts, electricalSilver Gross weight 250 g General data - FeaturesNumber of auxiliary contacts1Number of safety contacts 1SHG01.103/90Long lifeMetal enclosure40 mm x 108,5 mm x 43 mmHead positioned to the frontSafety appraisalStandards EN ISO 13849-1 Mission Time20 Year(s)Safety appraisal - Safety outputsB10d Normally-closed contact (NC)2,000,000 Operations B10d Normally open contact (NO)1,000,000 OperationsMechanical dataMechanical life, minimum1,000,000 Operations positive break travel11 mmPositive break force, minimum 5 NNote (Positive break force)per NCMechanical data - Connection techniqueTerminal Connector Screw connection Cable section, minimum0.5 mm²Cable section, maximum 2.5 mm²Note (Cable section)All indications about the cable section are including the conductor ferrules.Mechanical data - DimensionsLength of sensor43 mmWidth of sensor40 mmHeight of sensor108.5 mmAmbient conditionsDegree of protection IP 67 to IEC/EN 60529 Ambient temperature, minimum-25 °CAmbient temperature, maximum+70 °CAmbient conditions - Insulation valueRated insulation voltage U i400 VRated impulse withstand voltage U imp 2.5 kVElectrical dataThermal test current10 AUtilisation category AC-15230 VACUtilisation category AC-158 AUtilisation category DC-1324 VDCUtilisation category DC-13 5 ASwitching element NO contact, NC contactSwitching principle Creep circuit elementScope of deliveryIncluded in delivery Actuators must be ordered separately.Ordering codeProduct type description:SHG(1)/(2)(1)01Head positioned to the front02Head positioned to the left03Head positioned to the right04Head positioned to the rear(2)103/90 1 NC contact / 1 NO contact slow action switching contact220/1102 NC contacts slow action switching contact92/90 1 NC contact / 1 NO contact snap switching elementNotice Not all variations can be supplied. The available order code used to convert the product part name. PicturesProduct picture (catalogue individual photo)ID: kshg-f07| 81,4 kB | .png | 74.083 x 132.644 mm - 210 x 376Pixel - 72 dpi| 757,8 kB | .jpg | 278.694 x 499.886 mm - 790 x 1417Pixel - 72 dpiDimensional drawing basic componentID: kshg-g01| 3,9 kB | .png | 74.083 x 50.447 mm - 210 x 143 Pixel- 72 dpi| 27,1 kB | .cdr || 111,7 kB | .jpg | 352.778 x 240.594 mm - 1000 x 682Pixel - 72 dpiSwitch travel diagramID: kshg-s02| 19,6 kB | .cdr || 1,5 kB | .png | 74.083 x 17.992 mm - 210 x 51 Pixel -72 dpi| 33,4 kB | .jpg | 352.778 x 85.019 mm - 1000 x 241Pixel - 72 dpiDiagramID: ktzg-k01| 53,1 kB | .jpg | 352.778 x 128.058 mm - 1000 x 363Pixel - 72 dpi| 17,6 kB | .cdr |K.A. Schmersal GmbH & Co. KG, Möddinghofe 30, D-42279 WuppertalThe details and data referred to have been carefully checked. Images may diverge from original. Further technical data can be found in the manual. Technical amendments and errors possible.Generated on 27/05/2021 03:04:00。

西门子S1131消防产品手册

选配（最大配置）：
BCH1935 双琴台
（1）
1个
Rack/WG 立柜（带玻璃门）
（1）
1个
ZA2711B/24 火警通讯盘
1个
ZA2711B/40 火警通讯盘
*
1个
ZA5711A 总线制火警通讯盘
*
1个
ZA2715/10 电话主机
*
1个
ZA2715/30 电话主机
*
1个
ZA2721A 广播录放盘
*
设备外观
3
S1131 产品手册
类型
功能描述 / 技术参数
部件号
FS1120
FS1120 CC114x-/A/Rack 分布式系统控制器（上柜式）
CC114x-/A/Rack （瑞士部件，中国组装）
● 适用 S1131 分布式系统。 ● 设计容量：2000 点。 ● 标准 H67 安装底板组件，可安装于 BCH1950 双琴台或 Rack/WG
AC220V，± 15%，50/60Hz DC24V，38AH 0 ~ 50℃ - 20 ~ 60℃ ≤ 95%(40 ± 2℃) IP30 RAL 7035 淡灰色 434 X 1130 X 300 (mm)
基本配置：
CC1142 主 CPU 控制单元
1个
CT1142 控制面板终端
1个
E3M111 回路卡（4 回路） B2F020 电源（DC29V/6A）
基本配置：
BCH1950 双琴台
（1）
1个
CC1142 主 CPU 控制单元
1个
E3M111 回路卡（4 回路）
*
1块
B2F020 电源（DC29V/6A）

可朗妥安全数据表说明书

SECTION 1: Identification of the substance/mixture and of the company/undertaking1.1. Product Identifier Product name Canon Ink Tank CLI-581XL< C >Product Code(s)2049C1.2. Relevant identified uses of the substance or mixture and uses advised against UseInk for Ink Jet Printer1.3. Details of the supplier of the safety data sheet Supplier ImporterCanon Europa N.V.Bovenkerkerweg 59, 1185XB Amstelveen, The Netherlands +31 20 5458545, +31 20 5458222Manufacturer Canon Inc.30-2, Shimomaruko 3-Chome, Ohta-ku, Tokyo 146-8501, Japan 1.4. Emergency Telephone Number *1 Kontakt Giftlinien på tlf.nr.: 82 12 12 12 (åbent 24 timer i døgnet). Se punkt 4 om førstehjælp.*2 Only for the purpose of informing medical personnel in cases of acute intoxications.*3 Ask for Poison InformationSECTION 2: Hazards identification2.1. Classification of the substance or mixtureClassification according to Regulation (EC) No 1272/2008Not classified2.2. Label ElementsLabelling according to Regulation (EC) No 1272/2008112Safety Data SheetMalta 112Bulgaria Netherlands +31 (0)30-2748888 [*2]112Poland 112Version : 03Portugal +351 808 250 143CroatiaRomania +40 21 318 36 06+385 (0)1-23-48-342Slovakia +421 2 5477 4166Slovenia 112Cyprus Spain1121401Sweden 112 [*3]Issuing date : 19-Apr-2017United Kingdom 111 (UK only)Czech Republic Iceland 112+420 224919293Liechtenstein 145Norway+47 22 59 13 00Denmark Switzerland145+45 82 12 12 12 [*1]Estonia 16662SDS # : ICW 1784 R - 03 EU ENFinland +358 (0)9 471977France +33 (0)1 45 42 59 59Greece +30 210 7793777Austria Hungary +36 80 20 11 99+43 (0) 1 406 43 43Italy+39 (0)55 7947819Revision date : 31-Aug-2018Latvia+371 67042473Belgium Lithuania +370 687 53378+32 (0) 70 245 245LuxembourgHazard pictogramsNot requiredSignal wordNot requiredHazard statementsNot requiredPrecautionary statementsNot requiredOther InformationContains 1,2-benzisothiazol-3(2H)-one.May produce an allergic reaction.Contains less than 30% of components with unknown hazards to the aquatic environment.2.3. Other HazardsNoneSECTION 3: Composition/information on ingredients 3.2. MixturesChemical name CAS-No EC-No REACH registrationnumber Weight %Classification (Reg.1272/2008)Note toOtherHazardsGlycol CBI CBI CBI10 - 15NoneGlycerin56-81-5200-289-5None 5 - 10NoneUrea compound CBI CBI CBI 5 - 10Eye Irrit. 2 (H319)Substituted phthalocyanine salt CBI CBI CBI 1 - 5Eye Dam. 1 (H318)Aquatic Chronic 3 (H412) Water7732-18-5231-791-2None60 - 80NoneFull texts of Hazard statement(s) are listed in SECTION 16Note to Other Hazards : The following substance(s) is (are) marked with (1), (2) and/or (3)- (1) Substance for which EU Occupational Exposure Limit(s) is (are) established (See SECTION 8)- (2) PBT substance or vPvB substance under Regulation (EC) No 1907/2006- (3) Substance listed in Candidate List of SVHC for Authorisation under Regulation (EC) No 1907/2006In case a safety data sheet supplied under (EC) No 1907/2006 Article 31-3 is necessary, please contact us.SECTION 4: First aid measures4.1. Description of first aid measuresInhalation Move to fresh air. Get medical attention immediately if symptoms occur.Ingestion Rinse mouth. Drink 1 or 2 glasses of water. Get medical attention immediately if symptomsoccur.Skin Contact Wash off immediately with soap and plenty of water. Get medical attention immediately ifsymptoms occur.Eye Contact Flush with plenty of water. Get medical attention immediately if symptoms occur.4.2. Most important symptoms and effects, both acute and delayedInhalation None under normal use. Symptoms of overexposure are dizziness, headache, tiredness,nausea, unconsciousness, cessation of breathing.Ingestion None under normal use. Ingestion may cause gastrointestinal irritation, nausea, vomitingand diarrhea.Skin Contact None under normal use.Eye Contact None under normal use. May cause slight irritation.Chronic Effects None under normal use.4.3. Indication of any immediate medical attention and special treatment neededNoneSECTION 5: Firefighting measures5.1. Extinguishing mediaSuitable extinguishing mediaUse CO 2, water, dry chemical, or foam.Unsuitable extinguishing mediaNone5.2. Special hazards arising from the substance or mixtureSpecial HazardNoneHazardous combustion productsCarbon dioxide (CO 2), Carbon monoxide (CO)5.3. Advice for firefightersSpecial protective equipment for fire-fightersNoneSECTION 6: Accidental release measures6.1. Personal precautions, protective equipment and emergency proceduresAvoid contact with skin, eyes and clothing.6.2. Environmental PrecautionsKeep out of waterways.6.3. Methods and material for containment and cleaning upWipe up with adsorbent material (e.g. cloth, fleece).6.4. Reference to other sectionsNoneSECTION 7: Handling and storage7.1. Precautions for safe handlingAvoid contact with skin, eyes and clothing. Clean contaminated surface thoroughly. Use with adequate ventilation.7.2. Conditions for safe storage, including any incompatibilitiesKeep in a dry, cool and well-ventilated place. Keep out of the reach of children. Keep away from direct sunlight. Keep away from heat and sources of ignition.7.3. Specific end usesInk for Ink Jet Printer. Obtain special instructions before use.SECTION 8: Exposure controls/personal protection8.1. Control parameters Exposure LimitsChemical nameEU OEL Austria Belgium Bulgaria Cyprus Glycerin 56-81-5None None TWA: 10 mg/m 3None NoneChemical nameCzech Republic Denmark Finland France GermanyGlycerin 56-81-5TWA: 10 mg/m 3Ceiling: 15 mg/m 3NoneTWA: 20 mg/m 3TWA: 10 mg/m 3DFG TWA: 200 mg/m 3inhalable fraction Ceiling / Peak: 400mg/m 3 inhalablefraction Chemical nameGreece Hungary IrelandItaly NetherlandsGlycerin 56-81-5TWA: 10 mg/m 3None TWA: 10 mg/m 3 mist STEL: 30 mg/m 3 mistNone None Chemical namePoland PortugalRomania Slovakia SpainGlycerin 56-81-5TWA: 10 mg/m 3inhalable fractionTWA: 10 mg/m 3 mist NoneNone TWA: 10 mg/m 3 mistChemical nameSweden United Kingdom Norway Switzerland Turkey Glycerin 56-81-5NoneTWA: 10 mg/m 3 mistNoneTWA: 50 mg/m 3inhalable dust STEL: 100 mg/m 3inhalable dustNone8.2. Exposure controlsAppropriate engineering controlsNone under normal use conditions.Individual protection measures, such as personal protective equipmentEye/face ProtectionNot required under normal use.Skin ProtectionNot required under normal use.Respiratory ProtectionNot required under normal use.Thermal hazardsNot Applicable SECTION 9: Physical and chemical properties9.1. Information on basic physical and chemical properties AppearanceCyan ; Liquid OdorSlight odorOdor threshold No data available pH7 - 9Evaporation RateNo data availableNo data availableFlash Point (°C)> 93.0°C (Tag. Closed Cup.); estimated Melting/Freezing point (°C)No data available Boiling Point/Range (°C)Flammability (solid, gas)Not Applicable Flammability Limits in AirUpper Flammability Limit None; estimatedLower Flammability Limit None; estimatedVapor pressure No data availableVapor density No data availableRelative density 1.0 - 1.1Solubility(ies)Water; misciblePartition coefficient: n-octanol/water No data available Autoignition Temperature (°C)None; estimated Decomposition Temperature (°C)No data available Viscosity (mPa s) 1 - 5Explosive properties None; estimatedOxidizing properties None; estimated9.2. Other InformationNo data availableSECTION 10: Stability and reactivity 10.1. ReactivityNone10.2. Chemical stabilityStable10.3. Possibility of Hazardous ReactionsNone10.4. Conditions to AvoidNone10.5. Incompatible materialsAcids, Bases, Oxidizing agents, Reducing agents.10.6. Hazardous Decomposition ProductsCarbon dioxide (CO 2), Carbon monoxide (CO), and/or Ammonia.SECTION 11: Toxicological information 11.1. Information on toxicological effectsAcute toxicity No data availableSkin corrosion/irritation Non-irritant (Estimate) (OECD Guideline)Serious eye damage/eye irritation Minimal irritant (Estimate) (OECD Guideline) Sensitization Non-sensitizer (Estimate) (OECD Guideline)Germ cell mutagenicity Ames test: NegativeCarcinogenicity No data availableReproductive Toxicity No data available STOT - single exposure No data available STOT - repeated exposure No data available Aspiration hazard No data available Other InformationNo data availableSECTION 12: Ecological information12.1. Toxicity Ecotoxicity effects No data available12.2. Persistence and degradability No data available12.3. Bioaccumulative potential No data available 12.4. Mobility in soil No data available12.5. Results of PBT and vPvB assessmentThis preparation contains no substance considered to be persistent, bioaccumulating nor toxic (PBT).This preparation contains no substance considered to be very persistent nor very bioaccumulating (vPvB).12.6. Other adverse effects No data availableSECTION 13: Disposal considerations13.1. Waste treatment methodsDispose of in accordance with local regulations.SECTION 14: Transport information14.3. Transport Hazard Class 14.1. UN numberNone None 14.4. Packing Group None14.5. Environmental Hazards Not classified as environmentally hazardous under UN Model Regulations and marine pollutant under IMDG Code.14.2. UN Proper Shipping Name 14.6. Special Precautions for usersIATA: Not regulatedNoneSECTION 15: Regulatory information15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture (EC) No 1907/2006 Authorisation Not regulated (EC) No 1907/2006 Restriction Not regulated (EC) No 1005/2009Not regulated (EC) No 850/2004Not regulated (EU) No 649/2012Not regulated Other InformationNone15.2. Chemical safety assessment NoneSECTION 16: Other informationFull text of H-Statements referred to under sections 2 and 3H318 - Causes serious eye damage H319 - Causes serious eye irritationH412 - Harmful to aquatic life with long lasting effectsKey literature references and sources for data- World Health Organization International Agency for Research on Cancer, IARC Monographs on the Evaluation on the Carcinogenic Risk of Chemicals to Humans- EU Regulation (EC) No 1907/2006, (EC) No 1272/2008, (EC) No 1005/2009, (EC) No 850/2004, (EU) No 649/2012Key or legend to abbreviations and acronyms used in the safety data sheet - PBT: Persistent, Bioaccumulative and Toxic - vPvB: very Persistent and very Bioaccumulative - SVHC: Substances of Very High Concern- EU OEL: Occupational exposure limits at Union level under Directive 2004/37/EC and (EU) 2017/2398, 98/24/EC, 91/322/EEC,2000/39/EC, 2006/15/EC, 2009/161/EU and (EU) 2017/164.- TWA: Time Weighted Average - STEL: Short Term Exposure Limit- GHS: Globally Harmonized System of Classification and Labelling of Chemicals - IARC: International Agency for Research on Cancer - IATA: International Air Transport Association - CBI: Confidential Business Information Issuing date :19-Apr-2017Revision date :31-Aug-2018Revision NoteSECTION 3 and 16 revisedThis product falls under (EC) No 1907/2006 Article 31-3.DisclaimerThe information provided on this SDS is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guide for safe handling, use, processing, storage,transportation, disposal and release and is not to be considered as a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other material or in any process, unless specified in the text.14.7. Transport in bulk according to Annex II of MARPOL and the IBC CodeNot Applicable。

Moxa AWK-1131A 产品说明书

AWK-1131A SeriesEntry-level industrial IEEE802.11a/b/g/n wireless AP/clientFeatures and Benefits•IEEE802.11a/b/g/n AP/client support•Millisecond-level Client-based Turbo Roaming1•Integrated antenna and power isolation•5GHz DFS channel supportCertificationsIntroductionThe AWK-1131A industrial wireless AP/client meets the growing need for faster data transmission speeds by supporting IEEE802.11n technology with a net data rate of up to300Mbps.The AWK-1131A is compliant with industrial standards and approvals covering operating temperature, power input voltage,surge,ESD,and vibration.The two redundant DC power inputs increase the reliability of the power supply.The AWK-1131A can operate on either the2.4or5GHz bands and is backwards-compatible with existing802.11a/b/g deployments to future-proof your wireless investments.The Wireless add-on for the MXview network management utility visualizes the AWK's invisible wireless connections to ensure wall-to-wall Wi-Fi connectivity.Improved Higher Data Rate and Channel Capacity•High-speed wireless connectivity with up to300Mbps data rate•MIMO technology to improve the capability of transmitting and receiving multiple data streams•Increased channel width with channel bonding technology•Supports flexible channel selection to build up wireless communication system with DFSSpecifications for Industrial-grade Applications•Redundant DC power inputs•Integrated isolation design with enhanced protection against environmental interference•Compact aluminum housing,IP30-ratedWireless Network Management With MXview Wireless•Dynamic topology view shows the status of wireless links and connection changes at a glance•Visual,interactive roaming playback function to review the roaming history of clients•Detailed device information and performance indicator charts for individual AP and client devicesSpecificationsWLAN InterfaceWLAN Standards802.11a/b/g/n802.11i Wireless SecurityModulation Type DSSSOFDMMIMO-OFDMFrequency Band for US(20MHz operating channels) 2.412to2.462GHz(11channels)5.180to5.240GHz(4channels)1.The Turbo Roaming recovery time indicated herein is an average of test results documented,in optimized conditions,across APs configured with interference-free20-MHz RF channels,WPA2-PSK security,and default Turbo Roaming parameters.The clients are configured with3-channel roaming at100Kbps traffic load.Other conditions may also impact roaming performance.For more information about Turbo Roaming parameter settings,refer to the product manual.5.260to5.320GHz(4channels)25.500to5.700GHz(11channels)25.745to5.825GHz(5channels)Frequency Band for EU(20MHz operating channels) 2.412to2.472GHz(13channels)5.180to5.240GHz(4channels)5.260to5.320GHz(4channels)25.500to5.700GHz(11channels)2Frequency Band for JP(20MHz operating channels) 2.412to2.484GHz(14channels)5.180to5.240GHz(4channels)5.260to5.320GHz(4channels)25.500to5.700GHz(11channels)2Wireless Security WEP encryption(64-bit and128-bit)WPA/WPA2-Enterprise(IEEE802.1X/RADIUS,TKIP,AES)WPA/WPA2-PersonalTransmission Rate802.11b:1to11Mbps802.11a/g:6to54Mbps802.11n:6.5to300MbpsTransmitter Power for802.11a23±1.5dBm@6to24Mbps21±1.5dBm@36Mbps20±1.5dBm@48Mbps18±1.5dBm@54MbpsTransmitter Power for802.11n(5GHz)23±1.5dBm@MCS0/820MHz18±1.5dBm@MCS7/1520MHz23±1.5dBm@MCS0/840MHz17±1.5dBm@MCS7/1540MHzTransmitter Power for802.11b26±1.5dBm@1Mbps26±1.5dBm@2Mbps26±1.5dBm@5.5Mbps25±1.5dBm@11MbpsTransmitter Power for802.11g23±1.5dBm@6to24Mbps21±1.5dBm@36Mbps19±1.5dBm@48Mbps18±1.5dBm@54MbpsTransmitter Power for802.11n(2.4GHz)23±1.5dBm@MCS0/820MHz18±1.5dBm@MCS7/1520MHz23±1.5dBm@MCS0/840MHz17±1.5dBm@MCS7/1540MHzTransmitter Power2.4GHz26dBm18dBm18dBm5GHz(UNII-1)23dBm21dBm21dBm5GHz(UNII-2)23dBm21dBm21dBm5GHz(UNII-2e)23dBm23dBm23dBm5GHz(UNII-3)23dBm––Note:Based on regional regulations,the maximum transmission power allowed onthe UNII bands is restricted in the firmware,as indicated above.Receiver Sensitivity for802.11a(measured at5.680 GHz)Typ.-90@6Mbps Typ.-88@9Mbps Typ.-88@12Mbps Typ.-85@18Mbps Typ.-81@24Mbps Typ.-78@36Mbps2.DFS(Dynamic Frequency Selection)channel support:In AP mode,when a radar signal is detected,the device will automatically switch to another channel.However,according to regulations,after switching channels,a60-second availability check period is required before starting the service.Typ.-74@48MbpsTyp.-72@54MbpsNote:Due to a limitation in the receiver sensitivity performance for channels153and 161,it is recommended to avoid using these channels in your critical applications.Receiver Sensitivity for802.11n(5GHz;measured at 5.680GHz)Typ.-69dBm@MCS720MHzTyp.-71dBm@MCS1520MHzTyp.-63dBm@MCS740MHzTyp.-68dBm@MCS1540MHzNote:Due to a limitation in the receiver sensitivity performance for channels153and 161,it is recommended to avoid using these channels in your critical applications.Receiver Sensitivity for802.11b(measured at2.437 GHz)Typ.-93dBm@1Mbps Typ.-93dBm@2Mbps Typ.-93dBm@5.5Mbps Typ.-88dBm@11MbpsReceiver Sensitivity for802.11g(measured at2.437 GHz)Typ.-88dBm@6Mbps Typ.-86dBm@9Mbps Typ.-85dBm@12Mbps Typ.-85dBm@18Mbps Typ.-85dBm@24Mbps Typ.-82dBm@36Mbps Typ.-78dBm@48Mbps Typ.-74dBm@54MbpsReceiver Sensitivity for802.11n(2.4GHz;measured at2.437GHz)Typ.-70dBm@MCS720MHz Typ.-69dBm@MCS1520MHz Typ.-67dBm@MCS740MHz Typ.-67dBm@MCS1540MHzWLAN Operation Mode Access point,Client,SnifferAntenna External,2/2dBi,Omni-directionalAntenna Connectors2RP-SMA femaleEthernet InterfaceStandards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)IEEE802.3ab for1000BaseT(X)IEEE802.1X for authentication10/100/1000BaseT(X)Ports(RJ45connector)1Ethernet Software FeaturesManagement DHCP Server/Client,DNS,HTTP,IPv4,LLDP,Proxy ARP,SMTP,SNMPv1/v2c/v3,Syslog,TCP/IP,Telnet,UDP,VLAN,Wireless Search Utility,MXview,MXview Wireless,MXconfigSecurity HTTPS/SSL,RADIUS,SSHTime Management SNTP ClientFirewallFilter ICMP,MAC address,IP protocol,Port-basedSerial InterfaceConsole Port RS-232,8-pin RJ45LED InterfaceLED Indicators PWR,FAULT,STATE,SIGNAL,WLAN,LANInput/Output InterfaceButtons Reset buttonPhysical CharacteristicsHousing MetalIP Rating IP30Dimensions58x115x70mm(2.29x4.53x2.76in)Weight307g(0.68lb)Installation DIN-rail mounting,Wall mounting(with optional kit)Power ParametersInput Current0.56A@12VDC,0.14A@48VDCInput Voltage12to48VDCPower Connector1removable4-contact terminal block(s)Power Consumption 6.96W(max.)Reverse Polarity Protection SupportedEnvironmental LimitsOperating Temperature Standard Models:0to60°C(32to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsEMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:4kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:2kV;Signal:1kVIEC61000-4-6CS:3VIEC61000-4-8PFMFRadio EN300328,EN301489-1/17,EN301893,FCC ID SLE-WAPN008,MIC,NCC,RCM,SRRC,WPC,KC,RCM,ANATELSafety EN60950-1,UL60950-1Vibration IEC60068-2-6MTBFTime749,476hrsStandards Telcordia SR332WarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x AWK-1131Series wireless AP/clientInstallation Kit1x cap,plastic,for RJ45port1x DIN-rail kitAntenna2x2.4/5GHz antennaDocumentation1x quick installation guide1x warranty cardDimensionsOrdering InformationModel Name Band Standards Operating Temp. AWK-1131A-EU EU802.11a/b/g/n0to60°C AWK-1131A-EU-T EU802.11a/b/g/n-40to75°C AWK-1131A-JP JP802.11a/b/g/n0to60°C AWK-1131A-JP-T JP802.11a/b/g/n-40to75°C AWK-1131A-US US802.11a/b/g/n0to60°C AWK-1131A-US-T US802.11a/b/g/n-40to75°C Accessories(sold separately)AntennasANT-WDB-ONF-07097dBi at2.4GHz or9dBi at5GHz,N-type(female),dual-band,omnidirectional antennaANT-WDB-ANM-03063dBi at2.4GHz or6dBI at5GHz,N-type(male),omnidirectional antennaANT-WDB-ONM-070707dBi at2.4GHz and07dBi at5GHz,N-type(male),dual-band omnidirectional antennaANT-WDB-ANM-05025dBi at2.4GHz or2dBI at5GHz,N-type(male),omnidirectional antennaANT-WDB-ARM-022dBi at2.4GHz or2dBi at5GHz,RP-SMA(male)omnidirectional rubber-duck antennaANT-WDB-ARM-02022dBi at2.4GHz or2dBi at5GHz,RP-SMA(male),dual-band,omnidirectional antennaANT-WDB-PNF-101110dBi at2.4GHz and11dBi at5GHz,N-type(female),dual-band directional antennaMAT-WDB-CA-RM-2-0205 2.4/5GHz,ceiling antenna,2/5dBi,MIMO2x2,RP-SMA-type(male)MAT-WDB-DA-RM-2-0203-1m 2.4/5GHz,desktop antenna,2/3dBi,MIMO2x2,RP-SMA-type(male),1m cableMAT-WDB-PA-NF-2-0708 2.4/5GHz,panel antenna,7/8dBi,MIMO2x2,N-type(female)ANT-WSB5-PNF-1616dBi at5GHz,N-type(female),single-band directional antennaANT-WSB-PNF-12-0212dBi at2.4GHz,N-type(female),single-band directional antennaANT-WSB-AHRM-05-1.5m5dBi at2.4GHz,RP-SMA(male),omnidirectional/dipole antenna,1.5m cableWireless Antenna CablesA-CRF-RFRM-J1-60RP-SMA(male)to RP-SMA(female)with JSF-141cable,0.6mA-CRF-RFRM-R4-150RF magnetic base,RP-SMA(male)to RP-SMA(female)RG-174/U cable,1.5mA-CRF-RMNM-L1-300N-type(male)to RP SMA(male)LMR-195Lite cable,3mA-CRF-RMNM-L1-600N-type(male)to RP SMA(male)LMR-195Lite cable,6mA-CRF-RMNM-L1-900N-type(male)to RP SMA(male)LMR-195Lite cable,9mSurge ArrestorsA-SA-NFNF-020to6GHz,N-type(female)to N-type(female)surge arresterA-SA-NMNF-020to6GHz,N-type(male)to N-type(female)surge arresterWireless AdaptersA-ADP-RJ458P-DB9F-ABC01DB9female to RJ45connector for the ABC-01SeriesWireless Terminating ResistorsA-TRM-50-RM50-ohm terminating resistor with RP-SMA male connectorWall-Mounting KitsWK-51-01Wall mounting kit with2plates(51.6x67x2mm)and6screws©Moxa Inc.All rights reserved.Updated Aug17,2022.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。

产品规格书 1.0 连接器规格书说明书

制订Edit审核Check批准ApprovalPage 1 of 7NO.: PS0020顾客产品名称型号Client Product Name: 产品名称型号Product Name: 1.0连接器产品编码Part Number: 规格书版本号Version Number: 0产品规格书PRODUCT SPECIFICATION编号Serial numberPS0020 版本号Version Number产品名称Product Name 1.0连接器产品规格书Product Specification产品编码Part Number1 适用范围Scope本产品规格书适用于乐清市杰渝电子有限公司生产的1.0电子连接器。

This product specification covers the requirements for. 1.0 connector, which is designed and manufactured by YUEQING JIEYU ELECTRONICS Co.,LTD.2 相关标准Related Standards以下参考文件是本规格书的一个组成部份。

若本规格书中的要求与产品图纸发生冲突，则产品图中的要求为优先；若本规格书中的要求与参考文件中的要求冲突，则本规格书为优先。

The following documents form a part of this specification. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence.GB/T 2421 电工电子产品环境试验T esting method for Environmental of Electrical ConnectorsGB/T 2423 电工电子产品环境试验T esting method for Environmental of Electrical ConnectorsGB 2424电工电子产品基本环境试验规程T esting method for Environmental of Electrical ConnectorsGB/T 5095电子设备用机电元件基本试验规程及测量方法T esting procedure/method for components of electric equipment3 产品简图&PCB布线图Product Drawing & PCB Lay out19.0 20.35 18.0 19.35 17.0 18.35 16.0 17.35 15.0 16.35磷铜镀锡Tin/platedQuantity材料Material备注Remark编号Serial numberPS0020 版本号Version Number产品名称Product Name 1.0连接器产品规格书Product Specification产品编码Part Number5 产品性能Performance5.1机械性能Mechanical序号No.项目Item 测试条件Test Condition 规格Requirement5.1.1外观Appearance目测Checking by eye视力：1.0以上Eyesight: > 1.0照明：（200～300）lxLamp: （200～300）lx目测距离：（0.3～0.5）mSpace: （0.3～0.5）m1塑料件表面应无明显疤痕、凹陷、开裂及影响使用的变形。

合理用药监测系统软件需求规格说明书-0411

合理用药监测系统软件需求规格说明书目录合理用药监测系统 (1)软件需求规格说明书 (1)1引言 (3)1.1目的 (3)1.2背景 (3)1.3参考资料 (3)2项目概述 (5)2.1软件系统目标 (5)2.2软件系统功能概要 (5)2.3软件系统中的角色 (5)2.4实现语言 (5)2.5用户特点 (6)3功能需求 (6)3.1总体功能需求 (6)3.3用例列表 (7)3.4用例说明 (7)3.4.1合理用药系统 (7)3.4.2阳光用药系统 (22)3.4.3防统方系统 (26)4非功能性需求 (33)4.1运行需求 (33)4.2性能需求 (33)4.2.1精度 (33)4.2.2高效性 (33)4.2.3灵活性 (34)4.3数据管理能力要求 (34)4.4故障处理要求 (34)4.5其他专门要求 (34)5运行环境规定 (34)5.1设备 (34)5.2支持软件 (35)1引言1.1目的本文档明确定义了用户对《合理用药监测系统》的业务需求，包括功能需求和非功能需求，是用户进行系统验收、设计人员进行系统设计和测试人员进行系统测试的主要依据。

预期读者为：►项目管理人员；►业务需求人员；►系统分析人员；►系统设计人员；►系统测试人员。

1.2背景随着社会的进步，信息技术的不断发展，传统的医院管理模式不再适应现在高速发展的现代化医院，甚至对医院的高速发展还会带来一定阻碍，主要体现在医院过多繁杂的程序上面浪费了大量的时间、人力和物力，虽然医院在管理上面投入不菲，但效果甚微，达不到理想的效果。

PASS主要提供“医嘱监测”和“药物信息查询”功能；同时为了完成药物过敏史、特殊人群、禁忌症、副作用等依赖于病人的过敏史和病理生理状态信息相关项目的监测功能，提供了单独的“病人过敏史及病理生理状态信息”管理功能，用于建立和管理病人的药物过敏史及病理生理状态信息；另外为了便于医生、药师等临床专业人员进行合理用药研究工作，还提供了“用药研究”功能术语与缩写解释1.3参考资料1、《中华人民共和国执业医师法》2、《医疗机构管理条例》3、《医疗机构诊疗科目名录》4、《医疗机构基本标准》5、《城镇职工基本医疗保险用药范围管理暂行办法》6、《城镇职工基本医疗保险－定点医疗机构管理暂行办法》7、GB 3304-1991 中国各民族名称的罗马字母拼写法和代码8、GB/T 15657—1995 中医病证分类与代码9、GB/T 16751.3-1997 中医临床诊疗术语治则治法部分10、GB/T 20988-2007 信息系统灾难恢复规范11、GB/T 22239-2008 信息安全技术信息系统安全等级保护基本要求12、GB/T 2261.1-2003 个人基本信息分类与代码第1部分人的性别代码13、GB/T 2261.2-2003 个人基本信息与分类代码婚姻状况代码14、GB/T 2261.4-2003 个人基本信息分类与代码第4部分从业状况(个人身份)代码15、GB/T 2659-2000 世界各国和地区名称代码16、GB/T 4658-1984 文化程度代码17、WS XXXX—2012 电子病历基本数据集18、WS XXXX—2012 基于居民健康档案的区域卫生信息平台技术规范19、WS XXXX—2012 基于电子病历的医院信息平台技术规范（征求意见稿）20、电子病历基本架构与数据标准（试行）（卫办发[2009] 130号）21、疾病分类与代码（修订版）（卫办综发[2011] 166 号）基于电子病历的医院信息平台建设技术解决方案（1.0版）（卫办综发〔2011〕39号）2项目概述2.1软件系统目标PASS（Prescription Automatic Screening System）翻译为“处方自动监测系统”，是根据临床合理用药专业工作的基本特点和要求，采用计算机数据库组织原理和技术，将科学、权威和最新的医学、药学和相关学科知识进行信息标准化处理，实现医嘱监测和药物信息查询功能，从而帮助医生、药师等临床专业人员在用药过程中即时、有效地掌握和利用医药知识，预防药物不良事件（ADE，Adervse Drug Event）的发生，实现合理用药目的的一个专业软件系统。

快检试剂包技术参数标准

快检试剂包技术参数标准快检试剂包是一种用于快速检测样品中特定物质或参数的试剂盒，广泛应用于医疗、食品安全监测、环境监测等领域。

由于其使用方便、检测速度快、结果准确、适用范围广等特点，快检试剂包在现代生产和生活中扮演着重要的角色。

为了保证快检试剂包的质量和性能，制定相应的技术参数标准显得尤为重要。

下面就是一份关于快检试剂包的技术参数标准。

一、通用标准1. 适用范围：快检试剂包适用于对水样、食品、生物样品等进行快速检测。

2. 包装规格：快检试剂包的包装规格应明确，包括每盒含有的试剂数量、包装材质、保质期等信息。

3. 使用说明：快检试剂包应配有清晰明了的使用说明书，包括操作步骤、存储条件、结果解读等内容。

4. 存储条件：快检试剂包的存储条件应在产品标签上明确标注，包括温度、光照等要求。

二、物理性能指标1. 外观：快检试剂包试剂盒的外观应无损伤、变形、污染等现象。

2. 标识：产品标识应清晰完整，包括产品名称、生产日期、封存日期等信息。

3. 化学药剂：试剂包中所含化学药剂的成分及含量应符合国家标准要求，且在产品标签上应有标注。

三、性能参数要求1. 灵敏度：对于不同检测项目，快检试剂包的灵敏度应符合国家标准要求。

2. 特异性：快检试剂包应具有良好的特异性，能够准确识别目标物质，不产生干扰反应。

3. 检测时间：快检试剂包的检测时间应短，一般不超过30分钟。

4. 准确性：快检试剂包的检测结果应准确可靠，与传统实验室检测结果一致性较高。

四、环境适应性1. 温度适应性：快检试剂包在不同温度条件下的稳定性应符合规定要求，包括运输、存储和使用环境。

2. 湿度适应性：快检试剂包应具有一定的湿度适应性，能够在不同湿度条件下保持稳定性。

五、安全性1. 试剂包材料：快检试剂包的试剂盒材料应符合国家相关食品安全标准，不产生有害物质。

2. 操作安全：使用快检试剂包的操作步骤应简单易懂，减少误操作的可能性。

3. 废弃物处理：快检试剂包使用后的废弃物应符合环保要求，不会对环境造成污染。

快检试剂包技术参数标准

快检试剂包技术参数标准快检试剂包是一种用于检测生物体或样本中特定物质的试剂套装，通常用于医学、生物科学和环境监测等领域。

为了确保产品的质量和使用效果，需要制定一份关于快检试剂包技术参数标准的文件，这份文件能够提供给生产厂家和使用单位，以指导产品的研发和使用，并确保产品的合格性和安全性。

一、产品概述快检试剂包是一种包含了用于检测特定生物标志物或物质的试剂和相关材料的套装，可用于定性或定量检测。

该套装通常包括检测试剂、试剂配制液、反应载体、操作说明书等。

快检试剂包适用于临床诊断、食品安全、环境监测等领域。

二、技术参数标准1. 产品规格- 快检试剂包的型号、规格和包装数量应明确标识，以便用户正确选择和存储。

2. 检测试剂成分- 检测试剂的成分应包括主要活性物质及其含量、辅助成分及其用途等详细信息。

3. 检测试剂稳定性- 快检试剂包中的检测试剂应具有较好的稳定性，可以在规定环境条件下保存一定的时间而不影响其性能。

4. 检测试剂灵敏度- 检测试剂的灵敏度应满足相关标准要求，可以快速、准确地检测目标物质的含量范围。

5. 反应时间- 快检试剂包中的反应时间指从加入样本到获得检测结果所需的时间，应符合用户的实际需求。

6. 操作要求- 快检试剂包的操作说明书应清晰简明，包括操作步骤、使用注意事项、结果解读等，确保用户能够正确使用试剂包进行检测。

7. 包装标识- 快检试剂包的包装上应明确标识产品的名称、型号、批号、生产日期、有效期、生产厂家信息等，以保证产品的可追溯性。

8. 质量控制- 生产厂家应建立完善的质量管理体系，包括原材料采购、生产工艺控制、产品质量检验等环节，确保产品质量符合标准要求。

9. 验收标准- 用户对快检试剂包进行验收时，可以参照相关标准进行检验，确保产品符合技术参数标准要求。

10. 应用范围- 快检试剂包应明确适用的检测样本类型、检测对象、使用领域等，以指导用户正确选择和使用产品。

三、质量控制快检试剂包的生产应符合相关的质量管理体系要求，必须严格按照生产工艺流程进行生产，确保产品的稳定性和可靠性。

高输出型霍尔素子交货说明书

１、绝对最大定额4．微型模制插件的安装保证条件（１）、至基板焊接安装推荐条件１）请避开至主体急加热·急冷的情况。

２）预热温度为３）焊接（例：回流法）温度为（２）、焊接方法及温度保证５、出口状态（１）、包装卷带构造６、素子外形图8、载带外形图SHANGHAI NICERA交货说明书10、共　７　页第　７　页重要注意事项１０－１．关于绝对最大使用规格的注意事项如果超过了规格极限值进行使用，产品会发生故障，请注意。

１０－２．保管上的注意事项请确认储存环境。

尤其是下列或类似情况可能导致外观损坏、特征缺陷和／或装配相关的劣化。

１０－２－１．长时间暴露在阳光直射、高温和高温的环境。

作为保管条件，在温度４０℃以下，湿度８０％以下的环境下，１０－２－２．使用。

长期的保管，存在质量劣化的风险，如可焊性等。

腐蚀性气体、有机性气体、以及酸性、碱性气体的环境１０－２－３．请在交货后１年以内１０－２－４．灰尘多的环境。

１０－３．使用上的注意事项请注意以下事项１０－３－１．请勿焚烧、销毁、压碎或化学分解本产品。

※特别是焚烧、酸、碱等反应，可能产生有毒气体，会对人体造成危险，所以请绝对禁止。

１０－３－２．本产品请不要入口。

１０－３－３．请根据相关法律和用户内部废物处置条例进行处理。

１０－４．静电注意事项处理本产品时，应确保人体使用静电手环等接地良好，设备、工具请正确地连接，避免发生静电积聚。

１０－５．关于保证范围的注意事项下述情况为保证范围外１０－５－１．当用户处理不当或使用不当时１０－５－２．交纳人以外被追加处理的场合１０－５－３．其他，天灾·灾害等，不符上海尼赛拉责任的场合此外，此处的保修范围是指更换产品本身。

因缺陷或不合格产品造成的损坏和／或交换费用不包括在内。

ＮＨＥ５２０ＦＳＲ－ＨＦ·上海尼赛拉傳感器有限公司。

125-1131-403;125-1191-403;中文规格书,Datasheet资料

NPort 6150 6250 Series Quick Installation Guide

KSZ8851-16MLL DEMO BOARD 48-PIN ETHERNET CONTROLLE

超米特电子有限公司产品说明书

SCALANCE X101-1 商品说明书

PCS-9705_X_说明书_国内中文_国内标准版_X_R1.03_(ZL_CKZZ5305.1108)

海康威视总线制报警主机操作手册

泌乳素放射免疫分析药盒说明书资料精

安信可 Ra-01SH 规格书说明书

SHG01.103商品说明书

西门子S1131消防产品手册

可朗妥安全数据表说明书

Moxa AWK-1131A 产品说明书

产品规格书 1.0 连接器规格书说明书

合理用药监测系统软件需求规格说明书-0411

快检试剂包 技术参数标准

快检试剂包 技术参数标准

高输出型霍尔素子交货说明书

快检试剂包技术参数标准

快检试剂包技术参数标准