常用唧嘴孔径及球位尺寸规格表
各种制式螺纹攻牙钻孔径和滚造径对照表
各种制式螺纹攻牙钻孔径和滚造径对照表，太全了金属加工2015-10-17 关注作者原文地址本表所推选钻头孔径，是针对攻牙加工时，能够很容易的了解钻头直径；而依据市售之标准钻头所选定的。
在使用钻头的情况下，由于钻头的形状及尺寸、精度、被钻孔之材质等，对于所钻孔的尺寸，精度有很大影响，所以使用本表之钻孔径，若有不当之处，应实际状况适当的变更钻头直径，本表依据2级牙制订。
公制精螺纹规格标准径2级牙钻孔径最大最小M1.0×0.25 0.75 0.785 0.729M1.1×0.25 0.85 0.885 0.829M1.2×0.25 0.95 0.985 0.929M1.4×0.3 1.10 1.142 1.075M1.6×0.35 1.25 1.321 1.221M1.7×0.35 1.35 1.421 1.321M1.8×0.35 1.45 1.521 1.421M2.0×0.4 1.60 1.679 1.567M2.2×0.45 1.75 1.838 1.713M2.3×0.4 1.90 1.979 1.867M2.5×0.45 2.10 2.138 2.013M2.6×0.45 2.20 2.238 2.113M3.0×0.5 2.50 2.599 2.459M3.0×0.6 2.40 2.44 2.280M3.5×0.6 2.90 3.010 2.850M4.0×0.7 3.30 3.422 3.242M4.0×0.75 3.25 3.326 3.106M4.5×0.75 3.80 3.878 3.688M5.0×0.8 4.20 4.334 4.134M5.0×0.9 4.10 4.170 3.930M6.0×1.0 5.00 5.153 4.917M7.0×1.0 6.00 6.153 5.917M8.0×1.25 6.80 6.912 6.647M9.0×1.25 7.80 7.912 7.647M10×1.5 8.50 8.676 8.376M11×1.5 9.50 9.676 9.376M12×1.75 10.30 10.441 10.106M14×2.0 12.00 12.210 11.735M16×2.0 14.00 14.210 13.835M18×2.5 15.50 15.744 15.294M20×2.5 17.50 17.744 17.294M22×2.5 19.50 19.744 19.294M24×3.0 21.00 21.252 2.752M27×3.0 24.00 24.252 23.752M30×3.5 26.50 26.771 26.211公制细螺纹规格标准径2级牙钻孔径最大最小M1.0×0.2 0.80 0.821 0.783M1.1×0.2 0.90 0.921 0.883M1.2×0.2 1.00 1.021 0.983M1.4×0.2 1.20 1.221 0.183M1.6×0.2 1.40 1.421 1.383M1.7×0.2 1.45 1.500 1.460M1.8×0.2 1.60 1.621 1.583M2.0×0.25 1.75 1.785 1.729M2.2×0.25 1.95 1.985 1.929M2.3×0.25 2.05 2.061 2.001M2.5×0.35 2.20 2.221 2.121M2.6×0.35 2.20 2.246 2.186M3.0×0.35 2.70 2.721 2.621M3.5×0.35 3.20 3.221 3.121M4.0×0.5 3.50 3.599 3.459M4.5×0.5 4.00 4.099 3.959M5×0.5 4.50 4.599 4.459M5.5×0.5 5.00 5.099 4.959M6.0×0.75 5.30 5.378 5.188M6.0×0.5 5.50 5.550 5.400M7.0×0.75 6.30 6.378 61.88M7.0×0.5 6.50 6.550 64.00M8.0×1.0 7.00 7.153 6.917M8.0×0.75 7.30 7.378 7.188M8×0.5 7.50 7.520 7.400M9×1.0 8.00 8.153 7.917M9×0.75 8.30 8.378 8.188M10×1.25 8.80 8.912 8.647M10×1.0 9.00 9.153 8.917M10×0.75 9.30 9.378 9.188M10×0.5 9.50 9.520 9.400M11×1.0 10.00 10.153 9.917M11×0.75 10.30 10.378 10.188 M11×1.5 10.50 10.676 10.376M12×1.25 10.80 10.912 10.647 公制细螺纹规格标准径2级牙钻孔径最大最小M12×1.0 11.00 11.153 10.917M12×0.5 11.50 11.520 11.4M14×1.5 12.50 12.676 12.376M14×1.0 13.00 13.153 12.917 M15×1.5 13.50 13.676 13.376 M15×1.0 14.00 14.153 13.917 M16×1.5 14.50 14.676 14.376 M16×1.0 15.00 15.153 14.917 M17×1.5 15.50 15.676 15.376 M17×1.0 16.00 16.153 15.917 M18×2.0 16.00 16.210 15.835 M18×1.5 16.50 16.670 16.376 M18×1.0 17.00 17.153 16.917 M20×2.0 18.00 18.210 17.835 M20×1.5 18.50 18.676 18.376 M20×1.0 19.00 19.153 18.917 M20×2.0 20.00 20.210 19.835 M22×1.5 20.50 20.676 20.376 M22×1.0 21.00 21.153 20.917 M24×2.0 22.00 22.210 21.835 M24×1.5 22.50 22.676 22.376 M24×1.0 23.00 23.153 22.917 M25×2.0 23.00 23.210 22.835 M25×1.5 23.50 23.676 23.376 M25×1.0 24.00 24.153 23.917 M26×1.5 24.50 24.676 24.376 M27×2.0 25.00 25.210 24.835 M27×1.5 25.50 25.676 25.376 M27×1.0 26.00 26.153 25.917 M28×2.0 26.00 26.210 25.835 M28×1.5 26.50 26.676 26.376 M28×1.0 27.00 27.153 26.917 M30×3.0 27.00 27.252 26.752 M30×2.0 28.00 28.210 27.835 M30×1.5 28.50 28.676 28.376 M30×1.0 29.00 29.153 28.917 M32×2.0 30.00 30.210 29.835 M32×1.5 30.50 30.676 30.376 M33×3.0 30.00 30.252 29.752 M33×2.0 31.00 31.210 30.835 M33×1.5 31.50 31.376 31.376 M35×1.5 33.50 33.676 33.376 M36×3.0 33.00 33.252 32.752 M36×2.0 34.00 34.210 33.835 M36×1.5 34.50 34.676 34.376 美制细螺纹规格(UNF) 标准径2级牙钻孔径最大最小番数牙外径NO.0-80(1.524) 1.25 1.305 1.182 NO.1-72(1.854) 1.55 1.612 1.474 NO.2-64(2.184) 1.85 1.912 1.756 NO.3-56(2.515) 2.10 2.197 2.025 NO.4-48(2.845) 2.40 2.458 2.271 NO.5-44(3.175) 2.70 2.740 2.551 NO.6-40(3.505) 2.90 3.022 2.820 NO.8-36(4.166) 3.50 3.606 3.404 NO.10-32(4.826) 4.10 4.165 3.963 NO.12-28(5.846) 4.60 4.724 4.496 1/4 -28 5.50 5.588 5.3605/16 -24 6.90 7.035 6.7823/8 -24 8.50 8.636 8.3827/16 -20 9.90 10.033 9.7291/2 -20 11.50 11.607 11.3299/16 -18 12.90 13.081 12.7515/8 -18 14.50 14.681 14.3513/4 -16 17.50 14.678 17.3237/8 -14 20.50 20.675 20.2701 -12 23.20 23.571 23.1141-1/8 -12 26.50 26.746 26.2891-1/4 -12 29.50 29.921 29.4641-3/8 -12 32.80 33.096 32.4641-1/2 -12 36.00 36.270 35.814无屑丝攻钻孔径规格精度等级RH4.5.6 RH7.8 RH9M1.0×0.25 0.86 0.88 -M1.1×0.25 0.96 0.98 -M1.2×0.25 1.06 1.08 -M1.4×0.3 1.24 1.25 -M1.6×0.35 1.41 1.43 -M1.7×0.35 1.51 1.53 -M1.8×0.35 1.61 1.63 -M2.0×0.4 1.78 1.80 -M2.2×0.45 1.95 1.98 -M2.3×0.4 2.08 2.10 -M2.5×0.45 2.25 2.28 -M2.6×0.45 2.35 1.38 -M3.0×0.5 2.73 2.75 -M3.0×0.6 3.17 3.20 -M4.0×0.7 3.62 3.65 3.69M5.0×0.8 4.56 4.60 4.64M6.0×1.0 5.45 5.50 5.55M7.0×1.0 6.45 6.50 6.55M8.0×1.25 7.31 7.38 7.44M10×1.5 9.18 9.25 9.32M10×1.25 9.31 9.38 9.44M12×1.75 11.04 11.12 11.21M12×1.25 11.31 11.38 11.44注:无槽丝攻之钻孔径,在上表所列之数值,由于被加工材料之材质、硬度、形状、尺寸等之影响,多少会有所变动，因此参考上表之同时,亦请增减若干.美制管螺纹规格(UNEF) 标准径2级牙钻孔径最大最小NO.12 -32 4.70 4.826 4.6231/4 -32 5.60 5.690 5.4865/16 -32 7.10 7.264 7.0873/8 -32 8.70 8.865 8.6617/16 -28 10.20 10.338 10.1351/2 -28 11.80 11.938 11.7099/16 -28 13.20 13.386 13.1325/8 -24 14.80 14.986 14.7323/4 -20 17.80 17.958 17.6787/8 -20 21.00 21.133 20.8531 -20 24.00 24.308 24.028美制粗螺纹规格(UNC) 标准径2级牙钻孔径番数牙外径最大最小NO.1-64(1.854) 1.55 1.582 1.425NO.2-56(2.184) 1.80 1.871 1.695NO.3-48(2.515) 2.10 2.146 1.941NO.4-40(2.845) 2.30 2.385 2.157NO.5-40(3.175) 2.60 2.697 2.487NO.6-32(3.505) 2.80 2.895 2.642NO.8-32(4.166) 3.40 3.530 3.302NO.10-24(4.826) 3.90 3.962 3.682NO.12-24(5.846) 4.50 4.597 4.3441/4 -20 5.10 5.257 4.9795/16 -18 6.60 6.731 6.4013/8 -16 8.00 8.153 7.9877/16 -14 9.40 9.500 9.1441/2 -13 10.80 11.023 10.5929/16 -12 12.20 12.446 11.9895/8 -11 13.60 12.868 13.3863/4 -10 16.20 16.840 16.3071 -8 22.20 22.606 21.9711-1/8 -7 25.00 25.349 24.6381-1/4 -7 28.20 28.524 27.8131-3/8 -6 30.80 31.115 30.3531-1/2 -6 34.00 34.290 33.5281-3/4 -5 39.50 39.827 38.9642 -4-1/2 45.20 45.593 44.679英制螺纹规格钻孔径硬材软材W1/8 - 40 2.65 2.60W5/32 - 32 3.25 3.20W3/16 - 24 3.75 3.70W1/4 - 20 5.10 5.00W5/16 - 18 6.60 6.50W3/8 - 16 8.00 7.90W7/16 - 14 9.40 9.30W1/2 - 12 10.70 10.50W9/16 - 12 12.30 12.00W5/8 - 11 13.70 13.50W3/4 - 10 16.70 16.50W7/8 - 9 19.50 19.30W1 - 8 22.40 22.00W1-1/8 - 7 25.00 24.80W1-1/4 - 7 28.30 28.00英制管螺纹规格标准径钻孔径最大最小PS1/16 -28 6.50 6.632 6.490PS1/8 -28 8.50 8.637 8.495PS1/4 - 19 11.40 11.549 11.341PS3/8 - 19 15.00 15.054 14.846PS1/2 - 14 18.50 18.773 18.489PS3/4 - 14 24.00 24.259 23.975PS1 - 11 30.20 30.471 30.111PS1-1/4 -11 38.80 39.132 38.772PS1-1/2 -11 44.80 45.025 44.665PS2 - 11 56.50 56.836 56.476英制管螺纹规格标准径有效牙部之长度(最小)中之母螺牙内径标准长度(最小)中之母螺牙内径使用绞刀时不用绞刀时PT1/16 -28 6.10 6.2 6.244 6.384PT1/4 -19 10.70 11 10.962 11.174PT3/8 -19 14.20 14.5 14.448 14.658PT1/2 -14 17.60 18 17.979 18.263PT3/4 -14 23.00 23.5 23.378 23.663Pt1 -11 29.00 29.5 29.459 29.822PT1-1/4 -11 37.50 38 37.976 38.339 PT1-1/2 -11 43.40 44 43.869 44.232 Pt2 -11 54.90 55.5 55.412 55.844美制螺纹滚造径规格钻孔径NPT NPS使用绞刀时不用绞刀时1/16 -27 6.1 6.25 6.351/8 -27 8.33 8.43 8.741/4 -18 10.72 11.13 11.133/8 -18 14.27 14.27 14.681/2 -14 17.48 17.86 18.263/4 -14 22.63 23.01 23.421 -11-1/2 28.58 28.98 29.361-1/4-11-1/2 37.31 37.69 38.11-1/2-11-1/2 43.66 44.04 44.452 -11-1/2 55.58 55.96 56.36英制螺纹滚造径规格滚造径W 3/16 - 24 4.08 - 4.05W 1/4 - 20 5.51 - 5.46W 5/16 - 18 7.01 - 6.95W 3/8 - 16 8.48 - 8.41W 7/16 - 14 9.92 - 9.85W 1/2 - 12 11.31 - 11.24W 9/16 -12 12.89 - 12.82公制螺纹规格滚造径M3.0×0.5 2.63 2.60M3.0×0.6 2.56 2.53M3.5×0.6 3.06 3.03M4.0×0.7 3.49 3.45M4.0×0.75 3.45 3.41M4.5×0.75 3.96 3.92M5.0×0.8 4.43 4.38M5.0×0.9 4.36 4.31M6.0×1.0 5.30 5.25M7.0×1.0 6.30 6.25M8.0×1.0 7.28 - 7.23M8.0×1.25 7.12 - 7.07M9.0×1.25 8.12 - 8.07M10×1.25 9.10 - 9.04M10×1.5 8.97 - 8.91M11×1.5 9.97 - 9.91M12×1.5 10.92 - 10.87M12×1.75 10.79 - 10.73 M14×2.0 12.63 - 12.56M16×2.0 14.63 - 14.56M18×2.5 16.31 - 16.23M20×2.5 18.31 - 18.23M22×2.5 20.31 - 20.23针车用螺纹规格(UNC) 滚造径SM 1/8 40 2.735 -2.688 SM 1/8 44 2.769 -2.722 SM 9/64 40 3.128 -3.083 SM 11/64 40 3.855 -3.805 SM 3/16 32 4.205 -4.155 SM 3/16 28 4.143 -4.093 SM 7/32 32 5.003 -4.955 SM 15/64 28 5.325 -4.955 SM 1/4 40 5.890 -5.735 SM 1/4 28 5.721 -5.366 SM 9/32 28 6.528 -6.648 SM 11/32 28 8.092 -8.432 SM 3/8 29 8.880 -8.015 SM 7/16 30 10.466 -10.401 SM 7/16 16 10.037 -9.967 SM 1/2 20 11.819 -11.749 SM 9/16 20 13.400 -13.425 美制粗螺纹规格(UNC) 滚造径NO.5-40 2.70 - 2.67NO.6-32 2.95 - 2.91NO.8-32 3.60 - 3.57NO.10-24 4.09 - 4.05NO.12-24 4.75 - 4.701/4 -20 5.50 - 5.455/16 -18 6.98 - 6.933/8 -16 8.45 - 8.407/16 -14 9.89 - 9.831/2 -13 11.39 - 11.329/16 -12 12.87 - 12.80美制细螺纹规格(UNF) 滚造径NO.5-44 2.73 - 2.70NO.6-40 3.05 - 3.02NO.8-36 3.66 - 3.63NO.10-32 4.26 - 4.80NO.12-28 4.84 - 4.801/4 -28 5.72 - 5.685/16 -24 7.20 - 7.163/8 -24 8.79 - 8.747/16 -20 10.23 - 10.181/2 -20 11.82 - 11.76本表所推选钻头孔径,是针对攻牙加工时,能够很容易的了解钻头直径;而依据市售之标准钻头所选定的.在使用钻头的情况下,由于钻头的形状及尺寸,精度,被钻孔之材质等,对于所钻孔的尺寸,精度有很大影响,所以使用本表之钻孔径,若有不当之处,应实际状况适当的变更钻头直径,本表依据2级牙制订.公制精螺纹规格标准径2级牙钻孔径最大最小M1.0×0.25 0.75 0.785 0.729M1.1×0.25 0.85 0.885 0.829M1.2×0.25 0.95 0.985 0.929M1.4×0.3 1.10 1.142 1.075M1.6×0.35 1.25 1.321 1.221M1.7×0.35 1.35 1.421 1.321M1.8×0.35 1.45 1.521 1.421M2.0×0.4 1.60 1.679 1.567M2.2×0.45 1.75 1.838 1.713M2.3×0.4 1.90 1.979 1.867M2.5×0.45 2.10 2.138 2.013M2.6×0.45 2.20 2.238 2.113M3.0×0.5 2.50 2.599 2.459M3.0×0.6 2.40 2.44 2.280M3.5×0.6 2.90 3.010 2.850M4.0×0.7 3.30 3.422 3.242M4.0×0.75 3.25 3.326 3.106M4.5×0.75 3.80 3.878 3.688M5.0×0.8 4.20 4.334 4.134M5.0×0.9 4.10 4.170 3.930M6.0×1.0 5.00 5.153 4.917M7.0×1.0 6.00 6.153 5.917M8.0×1.25 6.80 6.912 6.647M9.0×1.25 7.80 7.912 7.647M10×1.5 8.50 8.676 8.376M11×1.5 9.50 9.676 9.376M12×1.75 10.30 10.441 10.106 M14×2.0 12.00 12.210 11.735M16×2.0 14.00 14.210 13.835M18×2.5 15.50 15.744 15.294M20×2.5 17.50 17.744 17.294M22×2.5 19.50 19.744 19.294M24×3.0 21.00 21.252 2.752M27×3.0 24.00 24.252 23.752M30×3.5 26.50 26.771 26.211公制细螺纹规格标准径2级牙钻孔径最大最小M1.0×0.2 0.80 0.821 0.783M1.1×0.2 0.90 0.921 0.883M1.2×0.2 1.00 1.021 0.983M1.4×0.2 1.20 1.221 0.183M1.6×0.2 1.40 1.421 1.383M1.7×0.2 1.45 1.500 1.460M1.8×0.2 1.60 1.621 1.583M2.0×0.25 1.75 1.785 1.729M2.2×0.25 1.95 1.985 1.929M2.3×0.25 2.05 2.061 2.001M2.5×0.35 2.20 2.221 2.121M2.6×0.35 2.20 2.246 2.186M3.0×0.35 2.70 2.721 2.621M3.5×0.35 3.20 3.221 3.121M4.0×0.5 3.50 3.599 3.459M4.5×0.5 4.00 4.099 3.959M5×0.5 4.50 4.599 4.459M5.5×0.5 5.00 5.099 4.959M6.0×0.75 5.30 5.378 5.188M6.0×0.5 5.50 5.550 5.400M7.0×0.75 6.30 6.378 61.88M7.0×0.5 6.50 6.550 64.00M8.0×1.0 7.00 7.153 6.917M8.0×0.75 7.30 7.378 7.188M8×0.5 7.50 7.520 7.400M9×1.0 8.00 8.153 7.917M9×0.75 8.30 8.378 8.188M10×1.25 8.80 8.912 8.647M10×1.0 9.00 9.153 8.917M10×0.5 9.50 9.520 9.400M11×1.0 10.00 10.153 9.917M11×0.75 10.30 10.378 10.188 M11×1.5 10.50 10.676 10.376M12×1.25 10.80 10.912 10.647 公制细螺纹规格标准径2级牙钻孔径最大最小M12×1.0 11.00 11.153 10.917M12×0.5 11.50 11.520 11.4M14×1.5 12.50 12.676 12.376M14×1.0 13.00 13.153 12.917M15×1.5 13.50 13.676 13.376M15×1.0 14.00 14.153 13.917M16×1.5 14.50 14.676 14.376M16×1.0 15.00 15.153 14.917M17×1.5 15.50 15.676 15.376M17×1.0 16.00 16.153 15.917M18×2.0 16.00 16.210 15.835M18×1.5 16.50 16.670 16.376M18×1.0 17.00 17.153 16.917M20×2.0 18.00 18.210 17.835M20×1.5 18.50 18.676 18.376M20×1.0 19.00 19.153 18.917M20×2.0 20.00 20.210 19.835M22×1.5 20.50 20.676 20.376M22×1.0 21.00 21.153 20.917M24×2.0 22.00 22.210 21.835M24×1.5 22.50 22.676 22.376M24×1.0 23.00 23.153 22.917M25×2.0 23.00 23.210 22.835M25×1.5 23.50 23.676 23.376M25×1.0 24.00 24.153 23.917M26×1.5 24.50 24.676 24.376M27×2.0 25.00 25.210 24.835M27×1.5 25.50 25.676 25.376M27×1.0 26.00 26.153 25.917M28×2.0 26.00 26.210 25.835M28×1.5 26.50 26.676 26.376M28×1.0 27.00 27.153 26.917M30×3.0 27.00 27.252 26.752M30×2.0 28.00 28.210 27.835M30×1.5 28.50 28.676 28.376M32×2.0 30.00 30.210 29.835M32×1.5 30.50 30.676 30.376M33×3.0 30.00 30.252 29.752M33×2.0 31.00 31.210 30.835M33×1.5 31.50 31.376 31.376M35×1.5 33.50 33.676 33.376M36×3.0 33.00 33.252 32.752M36×2.0 34.00 34.210 33.835M36×1.5 34.50 34.676 34.376美制细螺纹规格(UNF) 标准径2级牙钻孔径最大最小番数牙外径NO.0-80(1.524) 1.25 1.305 1.182 NO.1-72(1.854) 1.55 1.612 1.474 NO.2-64(2.184) 1.85 1.912 1.756 NO.3-56(2.515) 2.10 2.197 2.025 NO.4-48(2.845) 2.40 2.458 2.271 NO.5-44(3.175) 2.70 2.740 2.551 NO.6-40(3.505) 2.90 3.022 2.820 NO.8-36(4.166) 3.50 3.606 3.404 NO.10-32(4.826) 4.10 4.165 3.963 NO.12-28(5.846) 4.60 4.724 4.496 1/4 -28 5.50 5.588 5.3605/16 -24 6.90 7.035 6.7823/8 -24 8.50 8.636 8.3827/16 -20 9.90 10.033 9.7291/2 -20 11.50 11.607 11.3299/16 -18 12.90 13.081 12.7515/8 -18 14.50 14.681 14.3513/4 -16 17.50 14.678 17.3237/8 -14 20.50 20.675 20.2701 -12 23.20 23.571 23.1141-1/8 -12 26.50 26.746 26.2891-1/4 -12 29.50 29.921 29.4641-3/8 -12 32.80 33.096 32.4641-1/2 -12 36.00 36.270 35.814无屑丝攻钻孔径规格精度等级RH4.5.6 RH7.8 RH9M1.0×0.25 0.86 0.88 -M1.1×0.25 0.96 0.98 -M1.2×0.25 1.06 1.08 -M1.4×0.3 1.24 1.25 -M1.6×0.35 1.41 1.43 -M1.7×0.35 1.51 1.53 -M1.8×0.35 1.61 1.63 -M2.0×0.4 1.78 1.80 -M2.2×0.45 1.95 1.98 -M2.3×0.4 2.08 2.10 -M2.5×0.45 2.25 2.28 -M2.6×0.45 2.35 1.38 -M3.0×0.5 2.73 2.75 -M3.0×0.6 3.17 3.20 -M4.0×0.7 3.62 3.65 3.69M5.0×0.8 4.56 4.60 4.64M6.0×1.0 5.45 5.50 5.55M7.0×1.0 6.45 6.50 6.55M8.0×1.25 7.31 7.38 7.44M10×1.5 9.18 9.25 9.32M10×1.25 9.31 9.38 9.44M12×1.75 11.04 11.12 11.21M12×1.25 11.31 11.38 11.44注:无槽丝攻之钻孔径,在上表所列之数值,由于被加工材料之材质、硬度、形状、尺寸等之影响,多少会有所变动，因此参考上表之同时,亦请增减若干.美制管螺纹规格(UNEF) 标准径2级牙钻孔径最大最小NO.12 -32 4.70 4.826 4.6231/4 -32 5.60 5.690 5.4865/16 -32 7.10 7.264 7.0873/8 -32 8.70 8.865 8.6617/16 -28 10.20 10.338 10.1351/2 -28 11.80 11.938 11.7099/16 -28 13.20 13.386 13.1325/8 -24 14.80 14.986 14.7323/4 -20 17.80 17.958 17.6787/8 -20 21.00 21.133 20.8531 -20 24.00 24.308 24.028美制粗螺纹规格(UNC) 标准径2级牙钻孔径番数牙外径最大最小NO.1-64(1.854) 1.55 1.582 1.425NO.2-56(2.184) 1.80 1.871 1.695NO.3-48(2.515) 2.10 2.146 1.941NO.4-40(2.845) 2.30 2.385 2.157NO.5-40(3.175) 2.60 2.697 2.487NO.6-32(3.505) 2.80 2.895 2.642 NO.8-32(4.166) 3.40 3.530 3.302 NO.10-24(4.826) 3.90 3.962 3.682 NO.12-24(5.846) 4.50 4.597 4.344 1/4 -20 5.10 5.257 4.9795/16 -18 6.60 6.731 6.4013/8 -16 8.00 8.153 7.9877/16 -14 9.40 9.500 9.1441/2 -13 10.80 11.023 10.5929/16 -12 12.20 12.446 11.9895/8 -11 13.60 12.868 13.3863/4 -10 16.20 16.840 16.3077/8 -9 19.50 19.761 19.1771 -8 22.20 22.606 21.9711-1/8 -7 25.00 25.349 24.6381-1/4 -7 28.20 28.524 27.8131-3/8 -6 30.80 31.115 30.3531-1/2 -6 34.00 34.290 33.5281-3/4 -5 39.50 39.827 38.9642 -4-1/2 45.20 45.593 44.679英制螺纹规格钻孔径硬材软材W1/8 - 40 2.65 2.60W5/32 - 32 3.25 3.20W3/16 - 24 3.75 3.70W1/4 - 20 5.10 5.00W5/16 - 18 6.60 6.50W3/8 - 16 8.00 7.90W7/16 - 14 9.40 9.30W1/2 - 12 10.70 10.50W9/16 - 12 12.30 12.00W5/8 - 11 13.70 13.50W3/4 - 10 16.70 16.50W7/8 - 9 19.50 19.30W1 - 8 22.40 22.00W1-1/8 - 7 25.00 24.80W1-1/4 - 7 28.30 28.00英制管螺纹规格标准径钻孔径最大最小PS1/16 -28 6.50 6.632 6.490PS1/8 -28 8.50 8.637 8.495PS1/4 - 19 11.40 11.549 11.341PS3/8 - 19 15.00 15.054 14.846PS1/2 - 14 18.50 18.773 18.489PS3/4 - 14 24.00 24.259 23.975PS1 - 11 30.20 30.471 30.111PS1-1/4 -11 38.80 39.132 38.772PS1-1/2 -11 44.80 45.025 44.665PS2 - 11 56.50 56.836 56.476英制管螺纹规格标准径有效牙部之长度(最小)中之母螺牙内径标准长度(最小)中之母螺牙内径使用绞刀时不用绞刀时PT1/16 -28 6.10 6.2 6.244 6.384PT1/8 -28 8.10 8.2 8.249 8.388PT1/4 -19 10.70 11 10.962 11.174PT3/8 -19 14.20 14.5 14.448 14.658PT1/2 -14 17.60 18 17.979 18.263PT3/4 -14 23.00 23.5 23.378 23.663Pt1 -11 29.00 29.5 29.459 29.822PT1-1/4 -11 37.50 38 37.976 38.339PT1-1/2 -11 43.40 44 43.869 44.232Pt2 -11 54.90 55.5 55.412 55.844美制螺纹滚造径规格钻孔径NPT NPS使用绞刀时不用绞刀时1/16 -27 6.1 6.25 6.351/8 -27 8.33 8.43 8.741/4 -18 10.72 11.13 11.133/8 -18 14.27 14.27 14.681/2 -14 17.48 17.86 18.263/4 -14 22.63 23.01 23.421 -11-1/2 28.58 28.98 29.361-1/4-11-1/2 37.31 37.69 38.11-1/2-11-1/2 43.66 44.04 44.452 -11-1/2 55.58 55.96 56.36英制螺纹滚造径规格滚造径W 3/16 - 24 4.08 - 4.05W 1/4 - 20 5.51 - 5.46W 5/16 - 18 7.01 - 6.95W 3/8 - 16 8.48 - 8.41W 7/16 - 14 9.92 - 9.85W 1/2 - 12 11.31 - 11.24W 9/16 -12 12.89 - 12.82规格滚造径M3.0×0.5 2.63 2.60M3.0×0.6 2.56 2.53M3.5×0.6 3.06 3.03M4.0×0.7 3.49 3.45M4.0×0.75 3.45 3.41M4.5×0.75 3.96 3.92M5.0×0.8 4.43 4.38M5.0×0.9 4.36 4.31M6.0×1.0 5.30 5.25M7.0×1.0 6.30 6.25M8.0×1.0 7.28 - 7.23M8.0×1.25 7.12 - 7.07M9.0×1.25 8.12 - 8.07M10×1.25 9.10 - 9.04M10×1.5 8.97 - 8.91M11×1.5 9.97 - 9.91M12×1.5 10.92 - 10.87M12×1.75 10.79 - 10.73 M14×2.0 12.63 - 12.56M16×2.0 14.63 - 14.56M18×2.5 16.31 - 16.23M20×2.5 18.31 - 18.23M22×2.5 20.31 - 20.23针车用螺纹规格(UNC) 滚造径SM 1/8 40 2.735 -2.688 SM 1/8 44 2.769 -2.722 SM 9/64 40 3.128 -3.083 SM 11/64 40 3.855 -3.805 SM 3/16 32 4.205 -4.155 SM 3/16 28 4.143 -4.093 SM 7/32 32 5.003 -4.955 SM 15/64 28 5.325 -4.955 SM 1/4 40 5.890 -5.735 SM 1/4 28 5.721 -5.366 SM 9/32 28 6.528 -6.648 SM 11/32 28 8.092 -8.432 SM 3/8 29 8.880 -8.015 SM 7/16 30 10.466 -10.401 SM 7/16 16 10.037 -9.967 SM 1/2 20 11.819 -11.749 SM 9/16 20 13.400 -13.425规格(UNC) 滚造径NO.5-40 2.70 - 2.67NO.6-32 2.95 - 2.91NO.8-32 3.60 - 3.57NO.10-24 4.09 - 4.05NO.12-24 4.75 - 4.701/4 -20 5.50 - 5.455/16 -18 6.98 - 6.933/8 -16 8.45 - 8.407/16 -14 9.89 - 9.831/2 -13 11.39 - 11.329/16 -12 12.87 - 12.80美制细螺纹规格(UNF) 滚造径NO.5-44 2.73 - 2.70NO.6-40 3.05 - 3.02NO.8-36 3.66 - 3.63NO.10-32 4.26 - 4.80NO.12-28 4.84 - 4.801/4 -28 5.72 - 5.685/16 -24 7.20 - 7.163/8 -24 8.79 - 8.747/16 -20 10.23 - 10.181/2 -20 11.82 - 11.76来源：直观学机械推荐阅读1.钢价惨烈下跌风暴即将来临?不要以为和你没关系2.世界名刀大全，简直太漂亮了免责声明：本文系网络转载，版权归原作者所有。
螺纹下孔径表(无屑丝攻用)
9
15.14 ~15.25 (100~80)
7
15.11 ~15.17 (100~90)
3/4 -16
10
18.22 ~18.32 (100~85)
7
18.18 ~18.25 (100~90)
7/8 -14
11
21.27 ~21.38 (100~85)
8
21.23 ~21.27 (100~95)
6-32
5
3.09 ~3.17 (100~75)
3
3.06 ~3.14 (100~75)
8-32
6
3.75 ~3.83 (100~75)
4
3.74 ~3.82 (100~75)
10-24
6
4.26 ~4.35 (100~80)
4
4.24 ~4.32 (100~80)
12-24
6
4.92 ~5.01 (100~80)
－
1.858~1.887 (100~80)
2.3×0.4
－
2.07 ~2.12 (100~80)
4
2.07 ~2.13 (100~75)
2.5×0.45
3
2.24 ~2.30 (100~80)
5
2.24 ~2.31 (100~75)
2.6×0.45
－
2.34 ~2.40 (100~80)
5
2.34 ~2.41 (100~75)
2
1.97 ~2.03 (100~65)
3-56
4
2.29 ~2.35 (100~65)
3
2.28 ~2.34 (100~65)
4-48
4
2.57 ~2.64 (100~70)
机加工螺纹攻牙钻孔直径对照表
机加工螺纹攻牙钻孔直径对照表螺纹攻牙钻孔直径对照表：公制粗螺纹规格标准径2级牙钻孔径最大最小M1.0×0.250.750.7850.729M1.1×0.250.850.8850.829M1.2×0.250.950.9850.929M1.4×0.3 1.10 1.142 1.075M1.6×0.35 1.25 1.321 1.221M1.7×0.35 1.35 1.421 1.321M1.8×0.35 1.45 1.521 1.421M2.0×0.4 1.60 1.679 1.567M2.2×0.45 1.75 1.838 1.713M2.3×0.4 1.90 1.979 1.867M2.5×0.45 2.10 2.138 2.013M2.6×0.45 2.20 2.238 2.113M3.0×0.5 2.50 2.599 2.459M3.0×0.6 2.40 2.44 2.280M3.5×0.6 2.90 3.010 2.850M4.0×0.7 3.30 3.422 3.242M4.0×0.75 3.25 3.326 3.106M4.5×0.75 3.80 3.878 3.688M5.0×0.8 4.20 4.334 4.134M5.0×0.9 4.10 4.170 3.930M6.0×1.0 5.00 5.153 4.917M7.0×1.0 6.00 6.153 5.917M8.0×1.25 6.80 6.912 6.647M9.0×1.257.807.9127.647M10×1.58.508.6768.376M11×1.59.509.6769.376M12×1.7510.3010.44110.106M14×2.012.0012.21011.735M16×2.014.0014.21013.835M18×2.515.5015.74415.294M20×2.517.5017.74417.294M22×2.519.5019.74419.294M24×3.021.0021.25220.752M27×3.024.0024.25223.752M30×3.526.5026.77126.211公制细螺纹规格标准径2级牙钻孔径最大最小M1.0×0.20.800.8210.783M1.1×0.20.900.9210.883M1.2×0.2 1.00 1.0210.983M1.4×0.2 1.20 1.2210.183M1.6×0.2 1.40 1.421 1.383M1.7×0.2 1.45 1.500 1.460M1.8×0.2 1.60 1.621 1.583M2.0×0.25 1.75 1.785 1.729M2.0×0.25 1.75 1.785 1.729 M2.2×0.25 1.95 1.985 1.929 M2.3×0.25 2.05 2.061 2.001 M2.5×0.35 2.20 2.221 2.121 M2.6×0.35 2.20 2.246 2.186 M3.0×0.35 2.70 2.721 2.621 M3.5×0.35 3.20 3.221 3.121 M4.0×0.5 3.50 3.599 3.459 M4.5×0.5 4.00 4.099 3.959 M5×0.5 4.50 4.599 4.459 M5.5×0.5 5.00 5.099 4.959 M6.0×0.75 5.30 5.378 5.188 M6.0×0.5 5.50 5.550 5.400 M7.0×0.75 6.30 6.37861.88 M7.0×0.5 6.50 6.55064.00 M8.0×1.07.007.153 6.917 M8.0×0.757.307.3787.188 M8×0.57.507.5207.400 M9×1.08.008.1537.917 M9×0.758.308.3788.188 M10×1.258.808.9128.647 M10×1.09.009.1538.917 M10×0.759.309.3789.188 M10×0.59.509.5209.400 M11×1.010.0010.1539.917 M11×0.7510.3010.37810.188 M11×1.510.5010.67610.376 M12×1.2510.8010.91210.647公制细螺纹规格标准径2级牙钻孔径最大最小M12×1.011.0011.15310.917 M12×0.511.5011.52011.4M14×1.512.5012.67612.376 M14×1.013.0013.15312.917 M15×1.513.5013.67613.376 M15×1.014.0014.15313.917 M16×1.514.5014.67614.376 M16×1.015.0015.15314.917 M17×1.515.5015.67615.376 M17×1.016.0016.15315.917 M18×2.016.0016.21015.835 M18×1.516.5016.67016.376 M18×1.017.0017.15316.917 M20×2.018.0018.21017.835 M20×1.518.5018.67618.376 M20×1.019.0019.15318.917 M20×2.020.0020.21019.835 M22×1.520.5020.67620.376 M22×1.021.0021.15320.917 M24×2.022.0022.21021.835 M24×1.522.5022.67622.376 M24×1.023.0023.15322.917 M25×2.023.0023.21022.835M25×1.523.5023.67623.376M25×1.523.5023.67623.376M25×1.024.0024.15323.917M26×1.524.5024.67624.376M27×2.025.0025.21024.835M27×1.525.5025.67625.376M27×1.026.0026.15325.917M28×2.026.0026.21025.835M28×1.526.5026.67626.376M28×1.027.0027.15326.917M30×3.027.0027.25226.752M30×2.028.0028.21027.835M30×1.528.5028.67628.376M30×1.029.0029.15328.917M32×2.030.0030.21029.835M32×1.530.5030.67630.376M33×3.030.0030.25229.752M33×2.031.0031.21030.835M33×1.531.5031.37631.376M35×1.533.5033.67633.376M36×3.033.0033.25232.752M36×2.034.0034.21033.835M36×1.534.5034.67634.376美制细螺纹规格(UNF)标准径2级牙钻孔径最大最小番数牙外径NO.0-80(1.524) 1.25 1.305 1.182 NO.1-72(1.854) 1.55 1.612 1.474 NO.2-64(2.184) 1.85 1.912 1.756 NO.3-56(2.515) 2.10 2.197 2.025 NO.4-48(2.845) 2.40 2.458 2.271 NO.5-44(3.175) 2.70 2.740 2.551 NO.6-40(3.505) 2.90 3.022 2.820 NO.8-36(4.166) 3.50 3.606 3.404 NO.10-32(4.826)4.10 4.165 3.963 NO.12-28(5.846)4.60 4.724 4.496 1/4 -28 5.50 5.588 5.360 5/16 -24 6.907.035 6.782 3/8 -248.508.6368.382 7/16 -209.9010.0339.729 1/2 -2011.5011.60711.329 9/16 -1812.9013.08112.751 5/8 -1814.5014.68114.351 3/4 -1617.5014.67817.323 7/8 -1420.5020.67520.270 1 -1223.2023.57123.114 1-1/8 -1226.5026.74626.289 1-1/4 -1229.5029.92129.464 1-3/8 -1232.8033.09632.464 1-1/2 -1236.0036.27035.814无屑丝攻钻孔径规格精度等级RH4.5.6RH7.8RH9M1.0×0.250.860.88-M1.1×0.250.960.98-M1.2×0.25 1.06 1.08-M1.2×0.25 1.06 1.08-M1.4×0.3 1.24 1.25-M1.6×0.35 1.41 1.43-M1.7×0.35 1.51 1.53-M1.8×0.35 1.61 1.63-M2.0×0.4 1.78 1.80-M2.2×0.45 1.95 1.98-M2.3×0.4 2.08 2.10-M2.5×0.45 2.25 2.28-M2.6×0.45 2.35 1.38-M3.0×0.5 2.73 2.75-M3.0×0.6 3.17 3.20-M4.0×0.7 3.62 3.65 3.69M5.0×0.8 4.56 4.60 4.64M6.0×1.0 5.45 5.50 5.55M7.0×1.0 6.45 6.50 6.55M8.0×1.257.317.387.44M10×1.59.189.259.32M10×1.259.319.389.44M12×1.7511.0411.1211.21M12×1.2511.3111.3811.44美制管螺纹规格(UNEF)标准径2级牙钻孔径最大最小NO.12 -32 4.70 4.826 4.623 1/4 -32 5.60 5.690 5.486 5/16 -327.107.2647.087 3/8 -328.708.8658.661 7/16 -2810.2010.33810.135 1/2 -2811.8011.93811.709 9/16 -2813.2013.38613.132 5/8 -2414.8014.98614.732 3/4 -2017.8017.95817.678 7/8 -2021.0021.13320.853 1 -2024.0024.30824.028美制粗螺纹规格(UNC)标准径2级牙钻孔径番数牙外径最大最小NO.1-64(1.854) 1.55 1.582 1.425 NO.2-56(2.184) 1.80 1.871 1.695 NO.3-48(2.515) 2.10 2.146 1.941 NO.4-40(2.845) 2.30 2.385 2.157 NO.5-40(3.175) 2.60 2.697 2.487 NO.6-32(3.505) 2.80 2.895 2.642 NO.8-32(4.166) 3.40 3.530 3.302 NO.10-24(4.826)3.90 3.962 3.682 NO.12-24(5.846)4.50 4.597 4.344 1/4 -20 5.10 5.257 4.979 5/16 -18 6.60 6.731 6.401 3/8 -168.008.1537.987 7/16 -149.409.5009.144 1/2 -1310.8011.02310.592 9/16 -1212.2012.44611.989 5/8 -1113.6012.86813.386 3/4 -1016.2016.84016.307 7/8 -919.5019.76119.177 1 -822.2022.60621.9711 -822.2022.60621.971 1-1/8 -725.0025.34924.638 1-1/4 -728.2028.52427.813 1-3/8 -630.8031.11530.353 1-1/2 -634.0034.29033.528 1-3/4 -539.5039.82738.964 2 -4-1/245.2045.59344.679英制螺纹规格钻孔径硬材软材W1/8 - 40 2.65 2.60W5/32 - 323.25 3.20W3/16 - 243.75 3.70W1/4 - 20 5.10 5.00W5/16 - 186.60 6.50W3/8 - 168.007.90W7/16 - 149.409.30W1/2 - 1210.7010.50W9/16 - 1212.3012.00W5/8 - 1113.7013.50W3/4 - 1016.7016.50W7/8 - 919.5019.30W1 - 822.4022.00W1-1/8 - 725.0024.80W1-1/4 - 728.3028.00英制管螺纹规格标准径钻孔径最大最小PS1/16 -28 6.50 6.632 6.490PS1/8 -288.508.6378.495PS1/4 - 1911.4011.54911.341PS3/8 - 1915.0015.05414.846PS1/2 - 1418.5018.77318.489PS3/4 - 1424.0024.25923.975PS1 - 1130.2030.47130.111PS1-1/4 -1138.8039.13238.772PS1-1/2 -1144.8045.02544.665PS2 - 1156.5056.83656.476英制管螺纹规格标准径有效牙部之长度(最小)中之母螺牙内径标准长度(最小)中之母螺牙内径使用绞刀时不用绞刀时PT1/16 -28 6.10 6.2 6.244 6.384 PT1/8 -288.108.28.2498.388 PT1/4 -1910.701110.96211.174 PT3/8 -1914.2014.514.44814.658 PT1/2 -1417.601817.97918.263 PT3/4 -1423.0023.523.37823.663 Pt1 -1129.0029.529.45929.822 PT1-1/4 -1137.503837.97638.339 PT1-1/2 -1143.404443.86944.232 Pt2 -1154.9055.555.41255.844美制螺纹滚造径规格钻孔径规格钻孔径NPT NPS使用绞刀时不用绞刀时1/16 -27 6.1 6.25 6.35 1/8 -278.338.438.74 1/4 -1810.7211.1311.13 3/8 -1814.2714.2714.68 1/2 -1417.4817.8618.26 3/4 -1422.6323.0123.42 1 -11-1/228.5828.9829.36 1-1/4-11-1/237.3137.6938.1 1-1/2-11-1/243.6644.0444.45 2 -11-1/255.5855.9656.36英制螺纹滚造径规格滚造径W 3/16 - 24 4.08 - 4.05W 1/4 - 20 5.51 - 5.46W 5/16 - 187.01 - 6.95W 3/8 - 168.48 - 8.41W 7/16 - 149.92 - 9.85W 1/2 - 1211.31 - 11.24W 9/16 -1212.89 - 12.82公制螺纹规格滚造径M3.0×0.6 2.56 2.53M3.5×0.6 3.06 3.03M4.0×0.7 3.49 3.45M4.0×0.75 3.45 3.41M4.5×0.75 3.96 3.92M5.0×0.8 4.43 4.38M5.0×0.9 4.36 4.31M6.0×1.0 5.30 5.25M7.0×1.0 6.30 6.25M8.0×1.07.28 - 7.23M8.0×1.257.12 - 7.07M9.0×1.258.12 - 8.07M10×1.259.10 - 9.04M10×1.58.97 - 8.91M11×1.59.97 - 9.91M12×1.510.92 - 10.87M12×1.7510.79 - 10.73M14×2.012.63 - 12.56M16×2.014.63 - 14.56M18×2.516.31 - 16.23M20×2.518.31 - 18.23M22×2.520.31 - 20.23针车用螺纹规格(UNC)滚造径SM 1/8 40 2.735 -2.688SM 1/8 44 2.769 -2.722SM 9/64 40 3.128 -3.083SM 11/64 40 3.855 -3.805SM 3/16 32 4.205 -4.155SM 3/16 28 4.143 -4.093SM 7/32 32 5.003 -4.955SM 15/64 28 5.325 -4.955SM 1/4 40 5.890 -5.735SM 1/4 40 5.890 -5.735 SM 1/4 28 5.721 -5.366 SM 9/32 28 6.528 -6.648 SM 11/32 288.092 -8.432 SM 3/8 298.880 -8.015 SM 7/16 3010.466 -10.401 SM 7/16 1610.037 -9.967 SM 1/2 2011.819 -11.749 SM 9/16 2013.400 -13.425美制粗螺纹规格(UNC)滚造径NO.5-40 2.70 - 2.67 NO.6-32 2.95 - 2.91 NO.8-32 3.60 - 3.57 NO.10-24 4.09 - 4.05 NO.12-24 4.75 - 4.701/4 -20 5.50 - 5.455/16 -18 6.98 - 6.933/8 -168.45 - 8.407/16 -149.89 - 9.831/2 -1311.39 - 11.32 9/16 -1212.87 - 12.80美制细螺纹规格(UNF)滚造径NO.5-44 2.73 - 2.70 NO.6-40 3.05 - 3.02 NO.8-36 3.66 - 3.63 NO.10-32 4.26 - 4.80 NO.12-28 4.84 - 4.801/4 -28 5.72 - 5.685/16 -247.20 - 7.163/8 -248.79 - 8.747/16 -2010.23 - 10.18 1/2 -2011.82 - 11.76。
攻牙孔径表
攻牙孔徑表公制牙 粗牙無溝絲攻適用孔徑螺紋牙套適用孔徑規格最小孔徑建議孔徑最小孔徑最大孔徑最小孔徑最大孔徑M 1*0.250.730.78M1.1*0.250.830.89M1.2*0.250.930.98M1.4*0.3 1.08 1.14 1.23 1.26M1.6*0.35 1.22 1.32M1.7*0.35 1.33 1.42 1.5 1.55M1.8*0.35 1.42 1.52M 2*0.4 1.57 1.67 1.77 1.83M2.2*0.45 1.71 1.84 1.95 2.01M2.3*0.4 1.87 1.97 2.07 2.13M2.5*0.45 2.01 2.14 2.25 2.31M2.6*0.45 2.12 2.23 2.35 2.41M 3*0.5 2.46 2.6 2.64 2.72 2.79 3.12 3.2M3.5*0.6 2.85 3.01 3.05 3.16 3.24M 4*0.7 3.24 3.42 3.47 3.6 3.69 4.17 4.3M4.5*0.75 3.69 3.88 3.92 4.07 4.17M 5*0.8 4.13 4.33 4.38 4.55 4.65 5.16 5.33 M 6*1.0 4.92 5.15 5.22 5.43 5.55 6.25 6.42 M 7*1.0 5.92 6.15 6.22 6.43 6.557.257.42 M 8*1.25 6.65 6.91 6.987.297.428.318.52 M 9*1.257.657.917.988.298.42M 10*1.58.388.688.759.159.310.3710.62 M 11*1.59.389.689.7510.1510.3M 12*1.7510.1110.4410.5311.0111.1912.4312.73 M 14*2.011.8412.2112.3114.4914.83 M 16*2.013.8414.2114.3116.4916.83 M 18*2.515.2915.7415.8518.5819.04 M 20*2.517.2917.7417.8520.5821.04 M 22*2.519.2919.7419.85M 24*3.020.7521.2521.38M 27*3.023.7524.2524.38M 30*3.526.2126.7726.92M 33*3.529.2129.7729.92M 36*4.031.6732.2732.42M 39*4.034.6735.2732.42M 42*4.537.1337.837.98M 45*4.540.1340.840.98M 48*5.042.5943.343.49公制牙 細牙無溝絲攻適用孔徑螺紋牙套適用孔徑規格最小孔徑建議孔徑最小尺寸最大尺寸最小孔徑最大孔徑M2.5*0.35 2.12 2.22 2.3 2.35M 3*0.35 2.62 2.72 2.8 2.85M3.5*0.35 3.12 3.22 3.3 3.35M 4*0.5 3.46 3.6 3.64 3.72 3.79M4.5*0.5 3.96 4.1 4.14 4.22 4.29M 5*0.5 4.46 4.6 4.64 4.72 4.79M5.5*0.5 4.96 5.1 5.14 5.22 5.29M 6*0.75 5.19 5.38 5.42 5.57 5.67M 7*0.75 6.19 6.38 6.42 6.57 6.67M 8*1.0 6.927.157.227.437.558.258.42 M 8*0.757.197.387.427.577.67M 9*1.07.928.158.228.438.55M 9*0.758.198.388.428.578.67M 10*1.258.658.918.989.299.4310.3110.52 M 10*1.08.929.159.229.439.5510.2510.42 M 10*0.759.199.389.429.579.67M 11*1.259.529.89.88M 11*1.09.9210.1510.2210.4310.55M 11*0.7510.1910.3810.4210.5710.67M 12*1.510.3810.6810.7511.1511.312.3712.62 M 12*1.2510.6510.9110.9811.2911.4312.3112.52 M 12*1.010.9211.1511.2211.4311.55M 14*1.512.3812.6812.7514.3714.4 M 14*1.012.9213.1513.22M 15*1.513.3813.6813.75M 15*1.013.9214.1514.22M 16*1.514.3814.6814.7516.3716.62 M 16*1.014.9215.1515.22M 17*1.515.3815.6815.75M 17*1.015.9216.1516.22M 18*2.015.8416.2116.31M 18*1.516.3816.6816.7518.3718.62 M 18*1.016.9217.1517.22M 20*2.017.8418.2118.31M 20*1.518.3818.6818.7520.3720.62 M 20*1.018.9219.1519.22M 22*2.019.8420.2120.31M 22*1.520.3820.6820.75M 22*1.020.9221.1521.22M 24*2.021.8422.2122.31M 24*1.522.3822.6822.75M 24*1.022.9223.1523.22M 25*2.022.8423.2123.31M 25*1.523.3823.6823.75M 25*1.023.9224.1524.22M 26*2.023.6324.0824.18M 26*1.524.3824.6824.75M 27*2.024.8425.2125.31M 27*1.525.3825.6825.75M 27*1.025.9226.1526.22M 28*2.025.8426.2126.31M 28*1.526.3826.6826.75M 28*1.026.9227.1527.22M 30*3.026.7527.2527.38M 30*2.027.8428.2128.31M 30*1.528.3828.6828.75M 30*1.028.9229.1529.22M 32*2.029.8430.2130.31M 32*1.530.3830.6830.75M 33*3.029.7530.2530.38M 33*2.030.8431.2131.31M 33*1.531.3831.6831.75M 35*1.533.3833.6833.75M 36*3.032.7533.2533.38M 36*2.033.8434.2134.31M 36*1.534.3834.6834.75M 38*2.035.6236.0836.18M 38*1.536.3836.6836.75M 39*3.035.7536.2536.38M 39*2.036.8437.2137.31M 39*1.537.3837.6837.75M 40*3.036.7537.2537.38M 40*2.037.8438.2138.31M 40*1.538.3838.6838.75M 42*4.037.6738.2738.42M 42*3.038.7539.2539.38M 42*2.039.8440.2140.31M 42*1.540.3840.6840.75M 45*4.040.6741.2741.42M 45*3.041.7542.2542.38M 45*2.042.8443.2143.31M 45*1.543.3843.6843.75M 48*4.043.6744.2744.42M 48*3.044.7545.2545.38M 48*2.045.8446.2146.31M 48*1.546.3846.6846.75M 50*3.046.7547.2547.38M 50*2.047.8448.2148.31英制牙 粗牙無溝絲攻適用孔徑螺紋牙套適用孔徑規格最小孔徑最大孔徑最小孔徑最大孔徑最小孔徑最大孔徑W 1/16-60 1.3W 3/32-48 1.9W 1/8 -40 2.6W 5/32-32 3.2W 3/16-24 3.8W 1/4 -205 5.1 5.63 5.77W 5/16-18 6.5 6.67.137.3W 3/8 -167.988.638.8W 7/16-149.39.410.0910.29W 1/2 -1210.510.711.611.82W 9/16 -121212.3W 5/8 -1113.513.7W 3/4 -1016.516.7W 7/8 -919.319.5W 1 -82222.4W1-1/8 -724.825W1-1/4 -72828.3W1-3/8 -630.330.5W1-1/2 -633.533.8W1-5/8 -535.736W1-3/4 -53939.2W1-7/8 -4.541.541.8W 2 -4.544.745美制牙 粗牙無溝絲攻適用孔徑螺紋牙套適用孔徑規格最小孔徑最大孔徑最小孔徑最大孔徑最小孔徑最大孔徑NO. 1-64UNC 1.43 1.58 1.63 1.71NO. 2-56UNC 1.69 1.87 1.93 2.02NO. 3-48UNC 1.94 2.15 2.22 2.32NO. 4-40UNC 2.16 2.39 2.49 2.61 2.95 3.07 NO. 5-40UNC 2.49 2.7 2.82 2.92 3.25 3.38 NO. 6-32UNC 2.64 2.9 3.05 3.19 3.66 3.81 NO. 8-32UNC 3.3 3.53 3.71 3.83 4.32 4.47 NO.10-24UNC 3.68 3.96 4.23 4.37 5.05 5.21 NO.12-24UNC 4.34 4.6 4.88 5.021/4 -20UNC 4.98 5.26 5.63 5.77 6.63 6.785/16-18UNC 6.4 6.737.137.38.338.483/8 -16UNC7.88.158.638.89.9110.11 7/16-14UNC9.149.5510.0910.2911.5111.76 1/2 -13UNC10.5911.0211.611.8213.0813.34 9/16-12UNC11.9912.4514.6814.94 5/8 -11UNC13.3913.8716.5916.84 3/4 -10UNC16.3116.8419.8420.09 7/8 -9 UNC19.1819.761-8 UNC21.9722.611-1/8 -7 UNC24.6425.351-1/4 -7 UNC27.8128.521-3/8 -6 UNC30.3531.121-1/2 -6 UNC33.5334.291-3/4 -5 UNC38.9639.832- 4 1/2UNC44.6845.59美制牙 細牙無溝絲攻適用孔徑螺紋牙套適用孔徑規格最小孔徑最大孔徑最小孔徑最大孔徑最小孔徑最大孔徑NO. 0-80UNF 1.18 1.31 1.34 1.41NO. 1-72UNF 1.47 1.61 1.65 1.72NO. 2-64UNF 1.76 1.91 1.96 2.04NO. 3-56UNF 2.02 2.2 2.26 2.35NO. 4-48UNF 2.27 2.46 2.55 2.64NO. 5-44UNF 2.55 2.74 2.85 2.95NO. 6-40UNF 2.82 3.02 3.15 3.24NO. 8-36UNF 3.4 3.61 3.77 3.86 4.32 4.44NO.10-32UNF 3.96 4.17 4.38 4.48 4.98 5.13NO.12-28UNF 4.5 4.72 4.97 5.081/4 -28UNF 5.36 5.59 5.83 5.95 6.53 6.715/16-24UNF 6.787.047.337.468.28.383/8 -24UNF8.388.648.939.089.789.967/16-20UNF9.7310.0310.3910.5411.4311.631/2 -20UNF11.3311.6111.9812.1213.0313.269/16-18UNF12.7513.085/8 -18UNF14.3514.6816.2616.483/4 -16UNF17.3217.6819.4319.687/8 -14UNF20.2720.671 -12UNF23.1123.571-1/8 -12UNF26.2926.751-1/4 -12UNF29.4629.921-3/8 -12UNF32.6433.11-1/2 -12UNF35.8136.27管用螺紋規格PF PS PT最小孔徑最大孔徑最小孔徑最大孔徑最小孔徑最大孔徑 1/88.578.858.58.648.118.251/411.4511.8911.3411.5510.7610.963/814.9515.414.8515.0514.2414.441/218.6319.1718.4918.7717.717.985/820.5921.133/424.1224.6623.9824.2623.123.387/827.8828.42130.2930.9330.1130.4729.129.46 1-1/834.9435.581-1/438.9539.5938.7739.1337.6237.981-1/244.8545.4944.6745.0343.5143.871-3/450.7951.43256.6657.356.4856.8455.0555.41規格NPT NPSC NPSM 1/88.48.89.0512929.830.5 1/411.111.511.85 1-1/437.738.539.2 3/814.314.915.3 1-1/24444.645.3 1/217.918.418.9525656.757.3 3/42323.824.3。
攻丝底孔全参数
攻丝底孔的使用参数表一、螺紋下孔徑表1、公制粗牙螺紋 JIS B 0209-1982(單位：mm)螺纹尺寸钻头直径螺纹下孔徑內螺紋小徑最小直径最大直径M 1 × 0.25 0.75 0.78 (80%) 0.729 0.7851.1 × 0.25 0.85 0.88 (80%) 0.829 0.8851.2 × 0.25 0.95 0.98 (80%) 0.929 0.9851.4 × 0.3 1.1 1.14 (80%) 1.075 1.1421.6 × 0.35 1.25 1.32 (75%) 1.221 1.3211.8 × 0.35 1.45 1.52 (75%) 1.421 1.5212 × 0.4 1.6 1.65 (80%) 1.567 1.6792.2 × 0.45 1.75 1.83 (75%) 1.713 1.8382.5 × 0.45 2.1 2.13 (75%) 2.013 2.1383 × 0.5 2.5 2.59 (75%) 2.459 2.5993.5 × 0.6 2.9 3.01 (75%) 2.850 3.0104 × 0.7 3.3 3.39 (80%) 3.242 3.4224.5 × 0.75 3.8 3.85 (80%) 3.688 3.8785 × 0.8 4.2 4.31 (80%) 4.134 4.3346 × 1 5 5.13 (80%) 4.917 5.1537 × 1 6 6.13 (80%) 5.917 6.1538 × 1.25 6.8 6.85 (85%) 6.647 6.9129 × 1.25 7.8 7.85 (85%) 7.647 7.91210 × 1.5 8.5 8.62 (85%) 8.376 8.67611 × 1.5 9.5 9.62 (85%) 9.376 9.67612 × 1.75 10.3 10.40 (85%) 10.106 10.44114 × 2 12 12.2 (85%) 11.835 12.21016 × 2 14 14.2 (85%) 13.835 14.21018 × 2.5 15.5 15.7 (85%) 15.294 15.74420 × 2.5 17.5 17.7 (85%) 17.294 17.74422 × 2.5 19.5 19.2 (85%) 19.294 19.74424 × 3 21 21.2 (85%) 20.752 21.25227 × 3 24 24.2 (85%) 23.752 24.25230 × 3.5 26.5 26.6 (90%) 26.211 26.77133 × 3.5 29.5 29.6 (90%) 29.211 29.77136 × 4 32 32.1 (90%) 31.670 32.27039 × 4 35 35.1 (90%) 34.670 35.27042 × 4.5 37.5 37.6 (90%) 37.129 37.79945 × 4.5 40.5 40.6 (90%) 40.129 40.79948 × 5 43 43.1 (90%) 42.587 43.297 註(1)M1.4以下等級：5H、M1.6以上等級：6H (2)基於JIS B 0209-1982標準2、公制細牙螺紋-01 JIS B 0211-1982(單位：mm)螺纹尺寸钻头直径螺纹下孔徑內螺紋小徑最小直径最大直径M 2.5 × 0.35 2.2 2.22 (75%) 2.121 2.2213 × 0.35 2.7 2.72 (75%) 2.621 2.7213.5 × 0.35 3.2 3.22 (75%) 3.121 3.2214 × 0.5 3.5 3.59 (75%) 3.459 3.5994.5 × 0.5 4 4.09 (75%) 3.959 4.0995 × 0.5 4.5 4.59 (75%) 4.459 4.5995.5 × 0.5 5 5.09 (75%) 4.959 5.0996 × 0.75 5.3 5.35 (80%) 5.188 5.3787 × 0.75 6.3 6.35 (80%) 6.188 6.3788 × 1 7 7.13 (80%) 6.917 7.1538 × 0.75 7.3 7.35 (80%) 7.188 7.3789 × 1 8 8.13 (80%) 7.917 8.1539 × 0.75 8.3 8.35 (80%) 8.188 8.37810 × 1.25 8.8 8.85 (85%) 8.647 8.912 10 × 1 9 9.13 (80%) 8.917 9.15310 × 0.75 9.3 9.35 (80%) 9.188 9.37811 × 1 10 10.13 (80%) 9.917 10.15311 × 0.75 10.3 10.35 (80%) 10.188 10.37812 × 1.5 10.5 10.62 (85%) 10.376 10.676 12 × 1.25 10.8 10.85 (85%) 10.647 10.912 12 × 1 11 11.13 (80%) 10.917 11.153 14 × 1.5 12.5 12.62 (85%) 12.376 12.67614 × 1 13 13.13 (80%) 12.917 13.15315 × 1.5 13.5 13.62 (85%) 13.376 13.67615 × 1 14 14.13 (80%) 13.917 14.15316 × 1.5 14.5 14.62 (85%) 14.376 14.67616 × 1 15 15.13 (80%) 14.917 15.15317 × 1.5 15.5 15.62 (85%) 15.376 15.67617 × 1 16 16.13 (80%) 15.917 16.15318 × 2 16 16.2 (85%) 15.835 16.210 18 × 1.5 16.5 16.62 (85%) 16.376 16.676 18 × 1 17 17.13 (80%) 16.917 17.153 20 × 2 18 18.2 (85%) 17.835 18.210 20 × 1.5 18.5 18.62 (85%) 18.376 18.676 20 × 1 19 19.13 (80%) 18.917 19.153 22 × 2 20 20.2 (85%) 19.835 20.210 22 × 1.5 20.5 20.62 (85%) 20.376 20.676 22 × 1 21 21.13 (80%) 20.917 21.153 24 × 2 22 22.2 (85%) 21.835 22.210 24 × 1.5 22.5 22.62 (85%) 22.376 22.67624 × 1 23 23.13 (80%) 22.917 23.15325 × 2 23 23.2 (85%) 22.835 23.210 25 × 1.5 23.5 23.62 (85%) 23.376 23.676 25 × 1 24 24.13 (80%) 23.917 24.153 M 26 × 1.5 24.5 24.62 (85%) 24.376 24.676 27 × 2 25 25.2 (85%) 24.835 25.210 27 × 1.5 25.5 25.62 (85%) 25.376 25.67627 × 1 26 26.13 (80%) 25.917 26.15328 × 2 26 26.2 (85%) 25.835 26.210 28 × 1.5 26.5 26.62 (85%) 26.376 26.676 28 × 1 27 27.13 (80%) 26.917 27.153 30 × 3 27 27.2 (85%) 26.752 27.25230 × 2 28 28.2 (85%) 27.835 28.210 30 × 1.5 28.5 28.62 (85%) 28.376 28.676 30 × 1 29 29.13 (80%) 28.917 29.153 32 × 2 30 30.2 (85%) 29.835 30.21032 × 1.5 30.5 30.62 (85%) 30.376 30.67633 × 3 30 30.2 (85%) 29.752 30.252 33 × 2 31 31.2 (85%) 30.835 31.210 33 × 1.5 31.5 31.62 (85%) 31.376 31.67635 × 1.5 33.5 33.62 (85%) 33.376 33.67636 × 3 33 33.2 (85%) 32.752 33.252 36 × 2 34 34.2 (85%) 33.835 34.210 36 × 1.5 34.5 34.62 (85%) 34.376 34.67638 × 1.5 36.5 36.62 (85%) 36.376 36.67639 × 3 36 36.2 (85%) 35.752 36.252 39 × 2 37 37.2 (85%) 36.835 37.21039 × 1.5 37.5 37.62 (85%) 37.376 37.67640 × 3 37 37.2 (85%) 36.752 37.252 40 × 2 38 38.2 (85%) 37.835 38.210 40 × 1.5 38.5 38.62 (85%) 38.376 38.676 42 × 4 38 38.1 (90%) 37.670 38.270 42 × 3 39 39.2 (85%) 38.752 39.252 42 × 2 40 40.2 (85%) 39.835 40.210 42 × 1.5 40.5 40.62 (85%) 40.376 40.676 45 × 4 41 41.1 (90%) 40.670 41.270 45 × 3 42 42.2 (85%) 41.752 42.252 45 × 2 43 43.2 (85%) 42.835 43.210 45 × 1.5 43.5 43.62 (85%) 43.376 43.676 48 × 4 44 44.1 (90%) 43.670 44.270 48 × 3 45 45.2 (85%) 44.752 45.252 48 × 2 46 46.2 (85%) 45.835 46.21048 × 1.5 46.5 46.62 (85%) 46.376 46.676 50 × 3 47 47.2 (85%) 46.752 47.252 50 × 2 48 48.2 (85%) 47.835 48.210 50 × 1.5 48.5 48.62 (85%) 48.376 48.676 註(1)等級：6H(2)基於JIS B 0211-1982標準3、美制粗牙螺紋 (單位：mm)螺纹尺寸钻头直径2B级螺纹下孔徑內螺紋小徑最小直径最大直径NO.1 -64UNC 1.55 1.57 (65%) 1.425 1.5822 -56 1.8 1.86 (65%) 1.695 1.8713 -48 2.1 2.14 (65%) 1.941 2.1464 -40 2.3 2.36 (70%) 2.157 2.3855 -40 2.6 2.69 (70%) 2.487 2.6976 -32 2.8 2.86 (75%) 2.642 2.895 8 -32 3.4 3.52 (75%) 3.302 3.530 10 -24 3.9 3.91 (80%) 3.683 3.962 12 -24 4.5 4.57 (80%) 4.344 4.5971/4 -20 5.1 5.25 (80%) 4.979 5.257 5/16 -18 6.6 6.72 (80%) 6.401 6.731 3/8 -16 8 8.15 (80%) 7.798 8.153 7/16 -14 9.4 9.50 (80%) 9.144 9.550 1/2 -13 10.8 11.0 (80%) 10.592 11.023 9/16 -12 12.2 12.3 (85%) 11.989 12.446 5/8 -11 13.6 13.8 (85%) 13.386 13.868 3/4 -10 16.5 16.8 (80%) 16.307 16.840 7/8 - 9 19.5 19.6 (85%) 19.177 19.761 1 - 8 22.2 22.5 (85%) 21.971 22.606 1 1/8 - 7 25 25.2 (85%) 24.638 25.349 1 1/4 - 7 28.2 28.4 (85%) 27.813 28.524 1 3/8 - 6 30.8 31.0 (85%) 30.353 31.115 1 1/2 - 6 34 34.2 (85%) 33.528 34.2901 3/4 - 5 39.5 39.8 (85%) 38.964 39.8272 - 4 45.2 45.3 (90%) 44.679 45.593 4、美制細牙螺紋 (單位：mm)螺纹尺寸钻头直径2B级螺纹下孔徑內螺紋小徑最小直径最大直径NO. 0 -80UNF 1.25 1.30 (65%) 1.182 1.3051 -72 1.55 1.61 (65%) 1.474 1.6122 -64 1.85 1.90 (65%) 1.756 1.9123 -56 2.1 2.17 (70%) 2.025 2.1974 -48 2.4 2.44 (70%) 2.271 2.4585 -44 2.7 2.74 (70%) 2.551 2.7406 -40 2.9 3.02 (70%) 2.820 3.0228 -36 3.5 3.59 (75%) 3.404 3.60610 -32 4.1 4.14 (80%) 3.963 4.16512 -28 4.6 4.70 (80%) 4.496 4.7241/4 -28 5.5 5.56 (80%) 5.360 5.5885/16 -24 6.9 7.02 (80%) 6.782 7.0353/8 -24 8.5 8.61 (80%) 8.382 8.6367/16 -20 9.9 10.01 (80%) 9.729 10.0331/2 -20 11.5 11.60 (80%) 11.329 11.6079/16 -18 12.9 13.07 (80%) 12.751 13.0815/8 -18 14.5 14.65 (80%) 14.351 14.6813/4 -16 17.5 17.59 (85%) 17.323 17.6787/8 -14 20.5 20.6 (85%) 20.270 20.6751 -12 23.2 23.5 (85%) 23.114 23.5711 1/8 -12 26.5 26.7 (80%) 26.289 26.7461 1/4 -12 29.5 29.9 (80%) 29.464 29.9211 3/8 -12 32.8 33.0 (85%) 32.639 33.0961 1/2 -12 36 36.2 (85%) 35.814 36.2715、英制粗牙螺紋 (單位：mm)螺紋尺寸下孔徑嵌合率A列(硬材B列(軟材A列直徑B列直徑內螺紋最小內螺紋最大質) 質) 徑徑W 1/8 2.6 2.5 70.7 83.0 70.0 88.33/16 3.7 3.6 78.4 85.8 70.0 88.31/4 5.1 5.0 76.9 83.0 70.5 88.35/16 6.6 6.5 74.0 99.5 70.1 88.43/8 8.0 7.9 75.0 80.0 69.5 88.27/16 9.4 9.3 73.7 80.0 69.0 88.81/2 10.7 10.5 73.8 81.2 69.0 88.29/16 12.3 12.0 73.4 84.4 69.0 88.25/8 13.7 13.5 73.5 80.3 69.6 88.53/4 16.7 16.5 72.3 78.4 69.6 88.37/8 19.5 19.3 75.4 80.9 70.1 88.41 22.4 22.0 73.8 83.6 71.0 88.21 1/8 25.0 24.8 76.9 81.3 72.0 88.41 1/4 28.3 28.0 74.3 80.7 72.0 88.41 3/8 30.5 30.3 81.6 85.3 73.8 88.61 1/2 33.8 33.5 79.3 84.8 73.8 88.61 5/8 36.0 35.7 81.1 85.7 74.8 88.31 3/4 39.2 39.0 80.7 83.8 74.8 88.31 7/8 41.8 41.5 80.6 84.7 74.7 88.42 45.0 44.7 80.2 84.4 74.7 88.46、英制管用螺紋 (單位：mm)管用螺紋尺寸JIS B 0203 JIS B 2301錐管內螺紋Rc(PT) 平行內螺紋Rp(PS) 錐管內螺紋計算值下孔徑計算值下孔徑計算值下孔徑1/16 6.230 6.2 6.490 6.5 －－1/8 8.235 8.2 8.495 8.5 8.191 8.2 1/4 10.941 10.9 11.341 11.4 10.945 10.9 3/8 14.428 14.4 14.846 14.9 14.388 14.4 1/2 17.950 18 18.489 18.5 17.943 18 3/4 23.349 23 23.975 24 23.305 231 29.423 29 30.111 30 29.353 291 1/4 37.940 38 38.772 39 37.890 381 1/2 43.833 44 44.565 45 43.720 432 55.412 55 56.476 56 55.406 552 1/2 70.701 71 72.009 72 70.788 703 83.201 83 84.709 85 83.364 833 1/2 95.547 96 97.155 97 95.747 954 107.834 108 109.855 110 108.322 1085 133.110 133 135.255 135 133.597 1336 158.510 159 160.655 161 158.810 1587 183.360 183 185.954 1868 208.560 209 211.354 2129 233.960 234 236.754 23710 259.166 259 262.154 26212 309.747 310 312.875 3137、美制管用耐密斜行螺紋(NPTF‧NPSF) (單位：mm)管用螺紋尺寸斜行螺紋(NPTF) 平行螺紋(NPSF) 鑽頭直徑鑽頭直徑使用鉸刀場合不使用鉸刀場合1/16 －0.234 ( 5.94) 0.246 ( 6.25) 1/4 0.250 ( 6.35) 1/8 21/64 0.328 ( 8.33) 0.339 ( 8.61) 11/32 0.344 ( 8.74) 1/4 27/64 0.422 (10.72) 7/16 0.438 (11.13) －0.444 (11.28) 3/8 9/16 0.562 (14.27) 37/64 0.578 (14.68) 37/64 0.578 (14.68) 1/2 11/16 0.688 (17.48) 45/64 0.703 (17.86) 23/32 0.719 (18.26) 3/4 57/64 0.891 (22.63) 59/64 0.922 (23.42) －0.922 (23.42) 1 1 1/8 1.125 (28.58) 1 5/32 1.156 (29.36) 1 5/32 1.156 (29.36) 1 1/4 1 15/32 1.469 (37.31) 1 1/2 1.500 (38.10) －－1 1/2 1 45/64 1.703 (43.26) 1 47/64 1.734 (44.04) －－2 2 3/16 2.188 (55.58) 2 7/32 2.219 (56.36) －－2 1/2 2 19/32 2.594 (65.89) 2 41/64 2.641 (67.08) －－上述鑽頭直徑來源於美制管用耐密斜行螺紋ANSI B1.20.3—1957 Dryseal Pipe Threads (Inch)標準8、公制螺紋(NRT) (單位：mm)螺紋尺寸1級螺紋用下孔徑2級螺紋用下孔徑RH 精度最小～最大(嵌合率％)RH精度最小～最大(嵌合率％)M 1 ×0.25 2 0.87 ~ 0.89 (100~85) 4 0.90 ~0.92 (100~80) 1.1×0.25 2 0.97 ~ 0.99 (100~85) 4 1.00 ~1.02 (100~80) 1.2×0.25 2 1.07 ~ 1.09 (100~85) 4 1.10 ~1.12 (100~80) 1.4×0.3 2 1.244~ 1.263 (100~85) 4 1.270~ 1.294 (100~80)1.7×0.35 2 1.51 ~ 1.54 (100~80) 4 1.54 ~ 1.58 (100~75)2 ×0.4 2 1.78 ~ 1.82 (100~80) 4 1.81 ~ 1.85 (100~75) 2.3×0.4 2 2.08 ~ 2.12 (100~80) 4 2.11 ~ 2.15 (100~75) 2.5×0.45 2 2.25 ~ 2.29 (100~80) 4 2.28 ~ 2.33 (100~75)2.6×0.45 2 2.35 ~ 2.39 (100~80) 4 2.38 ~ 2.43 (100~75)3 ×0.5 3 2.74 ~ 2.78 (100~80)5 2.76 ~ 2.81 (100~75)3.5×0.6 3 3.18 ~ 3.21 (100~85) 5 3.20 ~ 3.26 (100~75)4 ×0.7 4 3.63 ~ 3.67 (100~85) 6 3.65 ~ 3.70 (100~85)5 ×0.8 4 4.57 ~ 4.62 (100~85)6 4.59 ~ 4.66 (100~80)6 ×1 4 5.45 ~ 5.51 (100~85)7 5.48 ~ 5.57 (100~80)7 ×1 4 6.45 ~ 6.51 (100~85) 7 6.48 ~ 6.57 (100~80)8 ×1.25 5 7.31 ~ 7.38 (100~85) 7 7.34 ~ 7.41 (100~85) 8 ×1 4 7.45 ~ 7.51 (100~85) 7 7.48 ~ 7.57 (100~80) 10 ×1.5 5 9.16 ~ 9.22 (100~90) 7 9.18 ~ 9.28 (100~85) 10 ×1.25 5 9.31 ~ 9.38 (100~85) 7 9.34 ~ 9.41 (100~85) 10 ×1 5 9.46 ~ 9.52 (100~85) 7 9.48 ~ 9.57 (100~80) 12 ×1.75 5 11.01 ~11.08 (100~90) 8 11.05 ~11.15 (100~85) 12 ×1.5 5 11.16 ~11.22 (100~90) 7 11.18 ~11.28 (100~85) 12 ×1.25 5 11.31 ~11.38 (100~85) 7 11.34 ~11.41 (100~85) 12 ×1 5 11.46 ~11.52 (100~85) 7 11.48 ~11.57 (100~80) 14 ×2 6 12.83 ~12.95 (100~90) 10 12.92 ~13.04 (100~85) 14 ×1.5 5 13.16 ~13.22 (100~90) 9 13.21 ~13.30 (100~85) 16 ×2 6 14.87 ~14.95 (100~90) 10 14.92 ~15.04 (100~85)16 ×1.5 5 15.16 ~15.22 (100~90) 9 15.21 ~15.30 (100~80) 18 ×2.5 6 16.57 ~16.67 (100~90) 11 16.63 ~16.78 (100~85) 18 ×1.5 6 17.17 ~17.23 (100~90) 10 17.22 ~17.31 (100~85) 20 ×2.5 6 18.57 ~18.67 (100~90) 11 18.63 ~18.78 (100~85) 20 ×1.5 6 19.17 ~19.23 (100~90) 10 19.22 ~19.31 (100~85)9、美制粗牙螺紋(NRT) (單位：mm)螺紋尺寸2B級螺紋用下孔徑3B級螺紋用下孔徑RH 精度最小～最大(嵌合率％)RH精度最小～最大(嵌合率％)NO. 2-56UNC 4 1.96 ~ 2.02 (100~65) 3 1.95 ~ 2.01 (100~65) 3-48 4 2.25 ~ 2.32 (100~65) 3 2.23 ~ 2.31 (100~65) 4-40 5 2.52 ~ 2.60 (100~70) 3 2.50 ~ 2.58 (100~70) 5-40 5 2.86 ~ 2.93 (100~70) 3 2.83 ~ 2.91 (100~70) 6-32 5 3.09 ~ 3.17 (100~75) 3 3.06 ~ 3.14 (100~75) 8-32 6 3.75 ~ 3.83 (100~75) 4 3.74 ~ 3.82 (100~75) 10-24 6 4.26 ~ 4.35 (100~80) 4 4.24 ~ 4.32 (100~80) 12-24 6 4.92 ~ 5.01 (100~80) 4 4.90 ~ 4.96 (100~85) 1/4 -20 6 5.66 ~ 5.76 (100~80) 4 5.64 ~ 5.74 (100~80) 5/16 -18 7 7.18 ~ 7.29 (100~80) 5 7.15 ~ 7.24 (100~85) 3/8 -16 7 8.66 ~ 8.78 (100~80) 5 8.63 ~ 8.73 (100~85) 7/16 -14 7 10.11 ~10.25 (100~80) 5 10.08 ~10.19 (100~85) 1/2 -13 8 10.62 ~11.78 (100~80) 6 11.60 ~11.68 (100~90) 9/16 -12 10 13.14 ~13.27 (100~85) 8 13.11 ~13.24 (100~85) 5/8 -11 11 14.62 ~14.76 (100~85) 8 14.58 ~14.67 (100~90) 3/4 -10 12 17.67 ~17.88 (100~80) 9 17.63 ~17.74 (100~90) 7/8 - 9 12 20.68 ~20.85 (100~85) 9 20.64 ~20.75 (100~90)1 - 8 13 23.65 ~23.84 (100~85) 10 23.61 ~23.74 (100~90)二、螺紋下孔徑表(無屑絲攻用)1、美制細牙螺紋(NRT) (單位：mm)螺紋尺寸2B級螺紋用下孔徑3B級螺紋用下孔徑RH 精度最小～最大(嵌合率％)RH精度最小～最大(嵌合率％)NO. 2-64UNF 3 1.98 ~ 2.04 (100~65) 2 1.97 ~ 2.03 (100~65) 3-56 4 2.29 ~ 2.35 (100~65) 3 2.28 ~ 2.34 (100~65) 4-48 4 2.57 ~ 2.64 (100~70) 3 2.56 ~ 2.63 (100~70) 5-44 4 2.88 ~ 2.95 (100~70) 3 2.87 ~ 2.94 (100~70) 6-40 5 3.19 ~ 3.26 (100~70) 3 3.16 ~ 3.22 (100~75) 8-36 5 3.80 ~ 3.88 (100~75) 4 3.79 ~ 3.86 (100~75) 10-32 5 4.41 ~ 4.48 (100~80) 4 4.40 ~ 4.46 (100~80) 12-28 5 5.00 ~ 5.08 (100~80) 4 4.99 ~ 5.06 (100~80) 1/4 -28 5 5.86 ~ 5.93 (100~80) 4 5.85 ~ 5.92 (100~80) 5/16-24 6 7.38 ~ 7.46 (100~80) 5 7.36 ~ 7.43 (100~85) 3/8 -24 6 8.96 ~ 9.05 (100~80) 5 8.95 ~ 9.02 (100~85) 7/16-20 7 10.44 ~10.54 (100~80) 5 10.41 ~10.49 (100~85) 1/2 -20 7 12.02 ~12.12 (100~80) 5 12.00 ~12.05 (100~90) 9/16-18 9 13.55 ~13.66 (100~80) 7 13.53 ~13.58 (100~90) 5/8 -18 9 15.14 ~15.25 (100~80) 7 15.11 ~15.17 (100~90) 3/4 -16 10 18.22 ~18.32 (100~85) 7 18.18 ~18.25 (100~90)7/8 -14 11 21.27 ~21.38 (100~85) 8 21.23 ~21.27 (100~95)1 - 12 12 24.28 ~24.41 (100~85) 9 24.24 ~24.32 (100~90)2、英制管用平行螺紋(NRT) (單位：mm)螺紋尺寸RH精度最小～最大(嵌合率％)PF 1/8 6 9.24~ 9.35 (100~80)1/4 7 12.41~12.62 (100~75)3/8 7 15.92~16.12 (100~75)1/2 8 19.93~20.15 (100~80)3/4 8 25.41~25.64 (100~80)3、公制螺紋(HRT) (單位：mm)螺紋尺寸1級螺紋用下孔徑2級螺紋用下孔徑RH 精度最小～最大(嵌合率％)RH精度最小～最大(嵌合率％)M 1 ×0.25 2 0.858~0.879 (100~85) 4 0.858~0.887 (100~80) 1.2×0.25 2 1.058~1.079 (100~85) 4 1.058~1.087 (100~80)1.4×0.3 2 1.23 ~1.26 (100~85) 4 1.23 ~1.26 (100~80) 1.6×0.35 2 1.40 ~1.44 (100~80) 4 1.40 ~1.45 (100~75) 1.7×0.35 － 1.50 ~1.54 (100~80) 4 1.50 ~1.55 (100~75)1.8×0.35 2 1.60 ~1.64 (100~80) 4 1.60 ~1.65 (100~75)2 ×0.4 2 1.77 ~1.82 (100~80) 4 1.77 ~1.82 (100~80)2 ×0.25 2 1.858~1.887 (100~80) － 1.858~1.887 (100~80)2.3×0.4 － 2.07 ~2.12 (100~80) 4 2.07 ~2.13 (100~75) 2.5×0.45 3 2.24 ~2.30 (100~80) 5 2.24 ~2.31 (100~75)2.6×0.45 － 2.34 ~2.40 (100~80) 5 2.34 ~2.41 (100~75)3 ×0.6 3 2.72 ~2.73 (100~90) 5 2.66 ~2.73 (100~90)3 ×0.5 5 2.72 ~2.77 (100~80) 6 2.72 ~2.78 (100~75)3 ×0.35 3 2.80 ~2.84 (100~80)5 2.80 ~2.85 (100~75)3.5×0.6 3 3.16 ~3.21 (100~85) 5 3.16 ~3.25 (100~75)4 ×0.75 3 3.57 ~3.64 (100~85)6 3.57 ~3.64 (100~85)4 ×0.7 6 3.60 ~3.66 (100~85) 7 3.60 ~3.66 (100~85)4 ×0.5 3 3.71 ~3.77 (100~80)6 3.71 ~3.79 (100~75)5 ×0.9 3 4.49 ~4.59 (100~85) 7 4.49 ~4.59 (100~85)5 ×0.8 3 4.55 ~4.62 (100~85) 8 4.55 ~4.64 (100~80)5 ×0.5 3 2.72 ~4.77 (100~80)6 4.72 ~4.79 (100~75)6 ×1 4 5.43 ~5.52 (100~85)7 5.43 ~5.55 (100~80)6 ×0.75 3 5.57 ~5.64 (100~85) 7 5.57 ~5.66 (100~80)4、公制粗牙螺紋 HL-NRT (單位：mm)螺紋尺寸RH精度最小～最大(嵌合率％)M 3 ×0.5 3 3.39~3.43 (100~80)4 ×0.7 4 4.54~4.58 (100~85)5 ×0.8 4 5.61~5.66 (100~85)6 ×1 4 6.75~6.81 (100~85)8 ×1.25 5 8.93~9.01 (100~85)10 ×1.5 5 11.11~11.17 (100~90)10 ×1.25 5 10.93~11.01 (100~85)12 ×1.75 5 13.28~13.17 (100~90)12 ×1.5 5 13.11~13.17 (100~90)12 ×1.25 5 12.93~13.01 (100~85)三、螺紋下孔徑表(護套螺紋用)1、公制粗牙螺紋 (單位：mm)螺紋尺寸下孔徑鑽頭直徑最小直徑最大直徑M 2.5 × 0.45 2.60 2.65 2.62.6 × 0.45 2.70 2.75 2.73 × 0.5 3.12 3.20 3.14 × 0.7 4.17 4.30 4.25 × 0.8 5.16 5.33 5.26 × 1 6.25 6.42 6.38 × 1.25 8.31 8.52 8.410 × 1.5 10.37 10.62 10.512 × 1.75 12.43 12.73 12.514 × 2 14.49 14.83 14.516 × 2 16.49 16.83 16.518 × 2.5 18.58 19.04 19.020 × 2.5 20.58 21.04 21.022 × 2.5 22.58 23.04 23.024 × 2.5 24.70 25.25 25.0 2、公制細牙螺紋 (單位：mm)螺紋尺寸下孔徑鑽頭直徑最小直徑最大直徑M 10 × 1 10.25 10.42 10.310 × 1.25 10.31 10.52 10.412 × 1.25 12.31 12.52 12.512 × 1.5 12.37 12.62 12.514 × 1.5 14.37 14.62 14.516 × 1.5 16.37 16.62 16.518 × 1.5 18.37 18.62 18.520 × 1.5 20.37 20.62 20.520 × 2 20.47 20.83 20.522 × 1.5 22.37 22.62 22.524 × 1.5 24.37 24.62 24.524 × 2 24.47 24.83 24.530 × 1.5 30.37 30.62 30.53、美制粗牙螺紋 (單位：mm)螺紋尺寸下孔徑鑽頭直徑最小直徑最大直徑NO. 2 – 56UNC 2.29 2.39 2.33 – 48 2.64 2.74 2.74 – 40 2.95 3.07 3.05 – 40 3.25 3.38 3.36 – 32 3.66 3.81 3.78 – 32 4.32 4.47 4.410 – 24 5.05 5.21 5.112 – 24 5.61 5.77 5.71/4 – 20 6.63 6.78 6.75/16 – 8 8.33 8.48 8.43/8 – 16 9.91 10.11 10.07/16 – 14 11.51 11.76 11.51/2 – 13 13.08 13.34 13.19/16 – 12 14.68 14.94 14.74、美制細牙螺紋 (單位：mm)螺紋尺寸下孔径钻头直径最小直徑最大直徑NO. 4 – 48UNF 2.97 3.05 3.06 – 40 3.66 3.78 3.78 – 36 4.32 4.44 4.410 – 32 4.98 5.13 5.01/4 – 28 6.53 6.71 6.65/16 – 24 8.20 8.38 8.23/8 – 24 9.78 9.96 9.87/16 – 20 11.43 11.63 11.51/2 – 20 13.03 13.26 13.19/16 – 18 14.66 14.88 14.75/8 – 18 16.26 16.48 16.33/4 – 16 19.43 19.68 19.57/8 – 14 22.61 22.86 22.71 – 12 25.76 26.04 26.0各種換算表管用螺絲基準寸法(mm)規格英制JIS(PT) 美式ASA(NPT)山數外徑有效徑山數外徑有效徑1/16 7.723 27 7.77 7.142 1/8 28 9.728 9.147 27 10.116 9.489 1/4 19 13.157 12.301 18 13.427 12.487 3/8 19 16.662 15.806 18 16.866 15.926 1/2 14 20.955 19.793 14 20.980 19.772 3/4 14 26.441 25.279 14 26.326 25.1171 11 33.249 31.770 111/2 33.932 31.46111/4 11 41.910 40.431 111/2 41.689 40.218 11/2 11 47.803 46.324 111/2 47.689 46.2872 11 59.614 58.135 111/2 59.796 58.32521/2 11 75.184 73.705 8 72.273 70.1593 11 87.884 86.405 8 88.182 86.06831/2 11 100.330 98.851 8 100.691 98.7764 11 113.030 111.551 8 113.548 111.43341/2 11 125.730 124.2515 11 138.430 136.951 8 141.3 138.41251/2 11 151.130 149.6516 11 163.830 162.351 8 168.3 165.2527 11 189.230 187.7518 11 214.630 213.151 8 219.1 215.901美制螺絲外徑公厘(mm)換算表規格吋mmNO. 0 0.0600 1.5241 0.0730 1.8542 0.0860 2.1843 0.0990 2.5154 0.1120 2.8455 0.1250 3.1756 0.1380 3.5058 0.1640 4.16610 0.1900 4.82612 0.2160 5.486山數節距換算表山數(每25.4mm) 節距mm100 0.254080 0.317572 0.352864 0.396960 0.423356 0.453648 0.529244 0.577340 0.635036 0.705632 0.793828 0.907124 1.058320 1.270018 1.411116 1.587514 1.814313 1.953812 2.116711 2.309110 2.54009 2.82228 3.17507 3.62866 4.23335 5.08004 1/2 5.64444 6.35003 1/2 7.2571精彩文档3 1/4 7.8154 3 8.4667 2 7/8 8.8348 2 3/4 9.2364 2 5/8 9.6762 2 1/2 10.1600精彩文档。
常用螺纹底孔尺寸表-螺纹孔尺寸标准
常用螺纹底孔尺寸表-螺纹孔尺寸标准
常用螺纹底孔尺寸表-螺纹孔尺寸标准
常用螺纹底孔尺寸表包括：
1. M
2.5底孔尺寸：底孔直径为2.8mm，底孔深度为5.5mm。
2. M3底孔尺寸：底孔直径为
3.2mm，底孔深度为6.5mm。
3. M4底孔尺寸：底孔直径为
4.2mm，底孔深度为8.5mm。
4. M5底孔尺寸：底孔直径为
5.2mm，底孔深度为10.5mm。
5. M6底孔尺寸：底孔直径为
6.2mm，底孔深度为12.5mm。
6. M8底孔尺寸：底孔直径为8.2mm，底孔深度为16mm。
7. M10底孔尺寸：底孔直径为10.5mm，底孔深度为20mm。
8. M12底孔尺寸：底孔直径为13mm，底孔深度为25mm。
以上底孔尺寸参考了ISO标准，但也有根据其他标准进行的设计，具体应根据实际情况选择合适的底孔尺寸。
最全的螺纹孔径对照表
最全的螺纹孔径对照表在机械加工和制造领域，螺纹孔径的准确测量和选择是至关重要的。
螺纹孔的尺寸规格繁多，为了方便工程技术人员在设计、加工和装配过程中能够快速准确地找到所需的螺纹孔径数据，我们整理了这份最全的螺纹孔径对照表。
首先，让我们来了解一下什么是螺纹孔径。
螺纹孔径指的是在螺纹孔中，除去螺纹部分的内孔直径。
它是决定螺纹连接强度、密封性以及装配精度的重要参数。
常见的螺纹标准有公制螺纹和英制螺纹。
公制螺纹以毫米为单位，英制螺纹则以英寸为单位。
以下是公制螺纹孔径的对照表：M1 螺纹的孔径约为 075mm，M2 螺纹的孔径约为 16mm，M3 螺纹的孔径约为 25mm，M4 螺纹的孔径约为 33mm，M5 螺纹的孔径约为42mm，M6 螺纹的孔径约为 5mm，M8 螺纹的孔径约为 68mm，M10螺纹的孔径约为 85mm，M12 螺纹的孔径约为 102mm，M14 螺纹的孔径约为 12mm，M16 螺纹的孔径约为 14mm，M18 螺纹的孔径约为155mm，M20 螺纹的孔径约为175mm，M22 螺纹的孔径约为195mm，M24 螺纹的孔径约为 21mm，M27 螺纹的孔径约为 24mm，M30 螺纹的孔径约为 265mm，M33 螺纹的孔径约为 295mm，M36 螺纹的孔径约为 32mm，M39 螺纹的孔径约为 35mm，M42 螺纹的孔径约为375mm，M45 螺纹的孔径约为 405mm，M48 螺纹的孔径约为 43mm，M52 螺纹的孔径约为 475mm，M56 螺纹的孔径约为 505mm，M60 螺纹的孔径约为 545mm，M64 螺纹的孔径约为 585mm，M68 螺纹的孔径约为 62mm，M72 螺纹的孔径约为 66mm，M76 螺纹的孔径约为70mm，M80 螺纹的孔径约为 74mm，M85 螺纹的孔径约为 79mm，M90 螺纹的孔径约为 84mm，M95 螺纹的孔径约为 89mm，M100 螺纹的孔径约为 94mm。
攻牙底孔参数
攻牙底孔的使用参数表
一、螺紋下孔徑表
1、公制粗牙螺紋 JIS B 0209-1982(單位：mm)
註(1)M1.4以下等級：5H、M1.6以上等級：6H (2)基於JIS B 0209-1982標準2、公制細牙螺紋-01 JIS B 0211-1982(單位：mm)
單位：mm)
(2)基於JIS B 0211-1982標準
3、美制粗牙螺紋 (單位：mm)
4、美制細牙螺紋 (單位：mm)
5、英制粗牙螺紋 (單位：mm)
6、英制管用螺紋 (單位：mm)
7、美制管用耐密斜行螺紋(NPTF‧NPSF) (單位：mm)
8、公制螺紋(NRT) (單位：mm)
二、螺紋下孔徑表(無屑絲攻用)
1、美制細牙螺紋(NRT) (單位：mm)
2、英制管用平行螺紋(NRT) (單位：mm)
3、公制螺紋(HRT) (單位：mm)
4、公制粗牙螺紋 HL-NRT (單位：mm)
三、螺紋下孔徑表(護套螺紋用)
1、公制粗牙螺紋 (單位：mm)
2、公制細牙螺紋 (單位：mm)
3、美制粗牙螺紋 (單位：mm)
mm)
各種換算表
美制螺絲外徑公厘(mm)換算表
山數節距換算表。
P3-2 唧咀各部尺寸设计
P
P1
P1
P
P1
PS
2.5
4
3
6
4
8
PE
2.5
4
3
6
4
8
ABS
2.5
5
4
7
5
8
PC
3.0
5
4
8
5
10
4、A=arctg[(P1-P)/L],取整数1o、2o、3o、4o以方便加工锥孔,然后反推算P1,使之与表2中对应的值接近.
Originator:Shifeng Wu 模具设计标准（三）——浇注系统P3-2
Q-----注射速度即体积流速(单位：cm3/s)；
P1-----唧咀大头直径（单位：mm）。P1是根据有效流道半经计算而来Rn3=3.3Q/（r×3.14），
r为主流道剪切速率，5000 /s为宜。
②当唧咀直接灌入型腔时(即直浇口),直接进料口的推荐尺寸如表3:
进料口径塑件重量
塑料
100g以下
300g～800g
4.0
300～400
7.9～8.8
32000
10.6
1810～2415
14.5～16.0
3000
4.6
390～520
8.7～9.5
64000
12.8
3000～4000
17.2～18.9
其中: Qn----流经主流道的塑胶体积总量,即制品容量加上流道容量；(单位：cm3)
T------注射时间(单位：s)；
Q=(0.6～0.8)Qn/T
Qn(cm3)
T(s)
Q=(0.6～0.8)Qn/T
60
1
最全的螺纹孔径对照表(公制-英制)
2级牙钻孔径 最大 最小 0.785 0.729 0.885 0.829 0.985 0.929 1.142 1.075 1.321 1.221 1.421 1.321 1.521 1.421 1.679 1.567 1.838 1.713 1.979 1.867 2.138 2.013 2.238 2.113 2.599 2.459 2.440 2.280 3.010 2.850 3.422 3.242 3.326 3.106 3.878 3.688 4.334 4.134 4.170 3.930 5.153 4.917 6.153 5.917 6.912 6.647 7.912 7.647 8.676 8.376 9.676 9.376 10.441 10.106 12.210 11.835 14.210 13.835 15.744 15.294 17.744 17.294 19.744 19.294 21.252 20.752 24.252 23.752 26.771 26.211
螺纹攻牙钻孔径和滚造径对照表
公制粗螺纹
规格
M1.0*0.25 M1.1*0.25 M1.2*0.25 M1.4*0.3 M1.6*0.35 M1.7*0.35 M1.8*0.35 M2.0*0.4 M2.2*0.45 M2.3*0.4 M2.5*0.45 M2.6*0.45 M3.0*0.5 M3.0*0.6 M3.5*0.6 M4.0*0.7 M4.0*0.75 M4.5*0.75 M5.0*0.8 M5.0*0.9 M6.0*1.0 M7.0*1.0 M8.0*1.25 M9.0*1.25 M10*1.5 M11*1.5 M12*1.75 M14*2.0 M16*2.0 M18*2.5 M20*2.5 M22*2.5 M24*3.0 M27*3.0 M30*3.5
常用井眼及钻具尺寸
213∕16（71.4）
7（7.8）
213∕16（71.4）
9½(241)
213∕16(71.4)
12¼（311.2）
5（127.0）
313∕16（96.9）或315∕16（100.0）
8（203.2）
7（177.8）
6½（165.1）
6¼（158.8）
213∕16（71.4）
213∕16（71.4）
2¼（57.2）或213∕16（71.4）
2¼（57.2）或213∕16（71.4）
8（203.2）
7（177.8）
6½（165.1）
6¼（158.8）
213∕16（71.4）
2¼（57.2）或213∕16（71.4）2¼（57.2）或213∕16（71.4）
2¼（57.2）或213∕16（71.4）
15⅜(390)
213∕16(71.4)
（117.5）
2⅞（73.0）
115∕16（49.2）
4⅛（104.8）
2（50.8）
49∕16(116)
2(50)
注：以上井眼尺寸4⅝不用适合无磁钻铤，使用外径2⅞（73）或3½（88.9）的无磁承压钻杆（无磁承压钻杆的内径一般与钻杆内径相同，但一般根据钻井需要，内径的尺寸是可订做，如外径2⅞（73）的一般钻杆内径为115∕16（49.2），但在实际使用中的无磁承压钻杆内径为2¼（58））；其他无磁钻铤尺寸基本与钻铤尺寸相同，但在水平井中，达到水平段时，一般不用无磁钻铤，改用5（127.0）的无磁承压钻杆，内径一般为313∕16（96.9）或315∕16（100.0）。无磁承压钻杆内径一般根据不同钻井要求而不一样。
12⅛(308)