ZZG-13A使用说明书

合集下载

132掘进机机械部分说明书

一.安全警示1．操作1．1掘进机启动顺序：打开外来水阀门→预警→打开内喷雾水阀门→油泵电机→转载机→中间运输机→星轮→截割电机；1．2开动机器前，须发出警报，确认周边人员处于安全状态；1．3机械设备和人身处于危险状况时，应迅速按动紧急停止按钮；1．4严禁司机进入空顶区作业；1．5进行顶板支护、检查、更换截齿作业时，必须先将截割急停按钮（操作台前）锁紧；1．6所有液压元件及其接合处，严禁在泄漏状态下工作；2．维修保养2．1易损件更换时，应保持液压系统清洁，加工配合面不许污染、划伤；2．2整机润滑按润滑图要求，由专人定期对各润滑点进行注油；2．3关键部位的紧固螺栓应加紧固力矩，并符合设计要求；2．4人员必须进入机器下方维修时，要用木垛等物垫牢，经检查确保安全后，方可入内进行维修;2．5维修电气系统时，要严格按照警示牌“严禁带电开盖”操作。

先清扫外部，在周围空气相对湿度不大于90%(+25℃)的环境下，打开开关箱或操作箱，在高温及恶劣环境下尽量不要开箱；2．6机械、电气系统裸露部份的护罩，应安全可靠；3．安标控制件应具有安全标志证书，且在有效期内。

二．机械、液压部分1．主要技术参数1.1整机参数型号： EBZ132总体长度（m）： 8.95总体宽度（m）： 2.8总体高度（m）： 1.48机重（t）： 40地隙（mm）： 210卧底深度（mm）： 200龙门高度（mm）：420适应坡度：±19°截割硬度（Mpa）：≤70（非经济状态可达100Mpa）总功率（KW）： 207定位截割高度（m）： 4定位截割宽度（m）： 5.1定位截割断面（㎡）： 20.11.2 截割部截割头形状：圆锥台形截割头转数（r/mim）： 44电动机功率（KW）： 132截齿：镐形喷雾：内、外喷雾方式1.3 铲板部装载形式：四齿星轮式装载能力（m 3/min）： 3.4装载宽度（m）： 2.8星轮转数（r/min）： 33铲板卧底（mm）： 200铲板抬起（mm）： 3801.4 中间运输机形式：中双链刮板运输能力（m 3/min）： 4.4溜槽断面尺寸(mm)： 450×370（宽×高）链速（m/min）： 61张紧形式：弹簧、丝杠张紧1.5 行走部形式：履带式行走速度（m/min）： 0～6履带宽度（mm）： 520制动方式：一体式多片制动器对地压强（Mpa）： 0.135张紧形式：油缸张紧、卡板锁定1.6液压系统系统压力（Mpa）： 18柱塞变量双泵（ml/r）： A11VO130/130 1台液压马达行走部（ml/r）： A2FE125 2台铲板部（ml/r）： IAM1200 .H4 2台中间运输机（ml/r）： IAM400.H2 2台内喷雾（ml/r）： 1台油箱容量（L）： 500油泵电动机（KW）： 75 1台换向阀：手动式 2组冷却方式：水冷却式 1台油缸数量（个）： 101.7 水系统灭尘方式：内、外喷雾流量（L/min）： 100外喷雾压力（Mpa）： 1.5内喷雾压力（Mpa）： 3.0冷却部件：截割电动机、油箱1.8电气部分1.8.1 主回路额定电压（V）： AC1140/660额定电流（A）： 165.8/287额定频率（Hz）： 50输出分路数（路）： 4额定功率（KW）： 2581.8.2 操作箱规格型号： CX4-4/12E防爆形式：矿用本质安全型额定电压（V）： DC12额定功率（W）： 41.8.3 开关箱规格型号： KXJ4-258/1140(660)E防爆形式：矿用隔爆兼本质安全型额定电压（V）：主回路： 1140/660控制回路：AC220、AC120、AC 100、AC 24、DC24、DC12、DC5额定电流（A）：≤3001.8.4截割电机型式：隔爆、水冷、双鼠笼异步电动机规格型号： YBUS-132-6（绝缘等级H级、工作方式S1）额定电压（V）： AC1140/660 Y/△额定电流（A）： 85/1481.8.5油泵电机型式：隔爆、风冷、双鼠笼异步电动机规格型号： YBU-75(绝缘等级H级、工作方式S1)额定电压（V）： AC1140/660 Y/△额定电流（A）： 46/801.8.6截割急停、总急停按钮型式：矿用隔爆型规格型号： BZA24-0.1/24-01 附带锁紧装置额定电压（V）： DC24额定电流（A）： 5 内部按钮为常开用途：总急停按钮：用于紧急停机截割急停按钮：用于截割电机停止1.8.7 电铃型式：矿用隔爆型规格型号： BAL1-36/127-150额定电压（V）： AC127额定电流（A）： 0.35用途：开机信号，启动报警1.8.8照明灯型式：矿用隔爆型规格型号： DGY35/24B额定电压（V）： AC 24数量（盏）： 31.8.9甲烷传感器规格型号： GJC42. 使用操作掘进机操作分为液压、电气两部分，电气部分操作详见，《KXJ4-258/1140(660)E 矿用隔爆兼本质安全型开关箱使用说明书》和《CX4-4/12矿用本质安全型操作箱使用说明书》。

真空脱气机电脑控制器使用说明书1

真空脱气机说明书北京筑恒科技有限公司感谢您使用本公司产品，为了正确使用本机并充分发挥效用，请您在使用之前务必仔细阅读说明书！开箱检查：◇观察产品包装箱上标示的规格、型号，确认和您定购的相符◇按装箱单核对产品、附件的规格、数量◇确认本机在运输过程中没有损坏◇有任何问题请在3日内与本公司联络。

如在收到货物7日内未与本公司书面联络，则视同您已认可。

超过此限，恕不受理。

安全注意◇本机必须由具有相应资格的专业技术人员按说明书安装◇安装使用的配件必须符合国家电气标准◇确认电源电压在规定的范围之内。

保证良好的接地◇不能将强电接入弱电信号输入端售后服务◇在您遇到问题或设备故障时，请及时与我公司用户服务部门联系。

请您在反映问题时尽量说明：产品的型号、编号、配件、购买日期、使用情况、具体故障现象◇在正常安装、使用的情况下，本机自出厂之日起12个月内发生质量问题实行在厂免费保修。

超过保修期后视情况需收取相应费用◇如出现以下问题，应由用户承担相关费用：①使用不当造成的人为损坏②自然灾害及污染等造成的损坏③电源电压异常、电路连接不当等造成的损坏使用条件◇环境温度：0 ～ 45 ℃◇大气压力：86 ～ 106 Kpa◇相对湿度：< 90 %（无结露）◇额定电源电压：220V AC，频率：50Hz◇电源电压范围：额定值的85% ～ 110%◇强电线路和连接传感器等的弱电线路必须分别穿管走线，否则控制器可能无法正常工作◇温度传感器原配接线需延长时，应使用屏蔽线◇出厂随机所配温度传感器屏蔽线不可剪短或加长，否则可能导致温度测量误差◇控制器温度传感器输入端为两个时，用户如需加长引线，长度不可超过1米，否则可能导致温度测量误差一、概述SJL系列真空脱气机电脑控制器是我公司吸收国外先进技术，结合国内控制自动化的各种需要和具体应用现状，采用现代电脑控制技术，自主研发的新一代控制器。

适用于真空脱气机的自动控制，具有可靠性高、自动化程度高、使用方便、操作简单、功能丰富、控制灵活、造型美观、性能价格比高等优点。

便携式测振仪使用说明书

H I：高频范围，1k～15kHz用于轴承的振动测量
LO：低频范围，10（或5）Hz～1kHz，用于一般的振动测量
测量上限：
振动位移及速度的测量上限为：
位移：1.999 mm（峰-峰值）
速度：199.9mm/s（有效值）
振动加速度的峰值应该不超过199.9m/s2。
袖珍式测振仪可以测量最大199.9m/s2（峰值）的加速度。事实上，当加速度很高时，由于探杆（或传感器探头）与物体之间的碰撞，即使低于199.9m/s2（峰值），其测量也是不太容易的。通常实际加速度上限应该是50m/s2。
设置振动参量：
用测量参量选择开关选择测量参量：加速度、速度、位移。显示器右边的光标指示所选择物理量。
所测量的加速度单位是m/s2。如果加速度用G表示，可将所测量的值除以9.8(1G=9.8m/s2)
设置频率范围：
如果选择加速度测量，用频率范围开关选择频率范围。显示器左边的光标指示所选的频率范围。频率范围限制仅限于加速度测量。
测量---------------------------------------------6
信号输出-----------------------------------------7
温度测量---------------------------------------------7
故障听诊---------------------------------------------7
便携式测振仪
APM-320
使用说明书
便携式测振仪的型号说明 ------------------------------3
测量之前的准备工作----------------------------------3

上海亚享检铁仪有限公司轻载型金属检测机(金属探测器)使用说明书,专业生产销售检针机、验布机等

概述金属探测器的基本功能是在非金属介质中检测是否含有金属杂质。

金属杂质的存在将直接影响到产品的品质或者可能直接影响到重要生产设备的安全。

如果食品中含有金属杂质，将可能直接危及人身安全或健康。

适用于食品、药品、化工、塑料、化纤、采矿等各种不同应用。

●金属探测器的特点1．检测灵敏度高上海亚享检铁仪有限公司通过开发先进的检测线路，可以达到最高0.6mm 的检测灵敏度。

灵敏度是空载状况下把检测球放置在传送带表面测试得到的实际灵敏度。

实际检测灵敏度取决于被测产品和现场工作环境。

2．适应范围广亚享系列金属探测器可以适应于高温、低温工作环境。

在比较恶劣的工作环境，同样有出色的灵敏度表现。

3．检测参数调整方便亚享系列金属探测器的检测参数调整与测试方便、直观。

检测参数一致性与稳定性很好。

针对相同的检测产品，检测参数不随时间改变。

4．防水防尘性能好根据需要，可以达到IP-65防水要求。

主要技术参数金属检测机技术参数表附注：可根据客户特殊需要专门设计制造。

1.灵敏度调节方式铁和非铁磁性金属（如不锈钢）灵敏度分两路，分别根据需要可调。

2.报警方式光带和声音同时报警，并自动停机。

3.电源电源电压：AC220V 50H Z功率：60W第一章基本知识●金属探测器是什么，它的工作原理是怎样的？金属探测器是用来检测金属杂质的仪器。

通常，一台金属探测器是由发射器和接收传感器组成的，当金属通过由发射器产生的电磁场的时候，接收传感器上接收到的信号会有变化。

金属探测器中的电子元件“看到”这种变化并“判断”这种变化是否由金属引起。

如果发现有金属，执行相应报警或排除动作。

●金属探测对你有什么用？使用金属探测器通常有两个原因。

（1）保护您的贵重设备或关键设备。

（2）确保您的产品完美。

如果有金属碎屑混入了您的碾磨机、切片机、磨粉机或切割机等设备中，2亚享的格言品/ 牌/ 有/ 价/ 在/ 经/ 营用户的利益品/ 格/ 无/ 价/ 人/ 素/ 质将不可避免地对您的设备造成损坏。

13A型箱式炉909首末2页

1SSJ-13A 型箱式电炉操作说明一、概述SSJ-13A 型箱式电炉为1300℃的高温电炉，主要用于1300℃以下的产品烧结与实验。

炉材采用高档轻质炉衬，具有保温性能好、升温快、使用寿命长等优点。

温度控制采用台湾泛达AP909程序仪表，可按用户需要编制多段升温曲线，实现自动升温、保温，操作方便简单。

二、主要技术参数2.1 电源: 380V /单相2.2 最大输出功率: 6KW2.3 仪表控温精度 : ±1℃2.4 加热元件 : 硅碳棒2.5 控制方式： PID 程序控制2.6 炉膛有效尺寸：深300×宽250×高200(mm)2.7 最高使用温度： 1300℃三、电炉操作步骤3.1 确认面板上“电源”“加热”按钮开关都在弹起位置,然后给电炉送电。

3.2 按下电炉电源按钮,等待温控仪表出现初始窗口：PV 窗口（显示测量值）显示室温（如14℃）。

PV 下面的SV 窗口显示目标设定值0.0。

3.3 遵照后面3.6-3.9所说的步骤输入温度曲线，开始加热。

3.4 当温控曲线运行完毕,关闭加热键，按钮上的指示灯熄灭，加热结束。

当温控表"PV "窗口显示炉温低于400℃时，再关闭电源按钮，以便能从"PV"窗口继续看到炉温。

工作结束后，关闭电源总闸。

3.5 自动运行过程中如需关闭电炉，要同时按▽（减少键）和SET 键先结束程序运行，这时PRO 灯灭，SV 显示为0。

再关闭加热键，最后关闭电源开关。

（注意：每次开始运行电炉加热时，要确认仪表SV1值为0）3.6 以下6个步骤只按键、不要修改，当SV 显示为0时，按SET 键* 按第一次SET 键出现OUT （输出功率百分比），在后面的操作中设定，勿改动。

* 按第二次SET 键出现AT （PID 自整定设定），已设定好，勿改动。

* 按第三次SET 键出现AL1（报警设定），已设置好，勿改动。

柳树家居电器产品说明书

410TSDC36BNWH 410TSDC42BNBKREAD AND SAVE THESE INSTRUCTIONS.Internal model: YSDC-36YSDC-42A. 5”B. 3-3/4”C. 5-1/2”D. 36”Fan Motor Assembly Fan Blade (4 PCS)Blade Bracket (4 PCS)Wall Control Assembly Kit Installation InstructionsHousing Turn Disk Shaft Nut Unpack your fan and check the contents.You should have the following items.A. 5”B. 3-3/4”C. 5-1/2”D. 42”410TSDC36BNWH 410TSDC42BNBKInternal model: YSDC-36YSDC-4223410TSDC36BNWH 410TSDC42BNBKInternal model: YSDC-36YSDC-424WARNING:410TSDC36BNWH 410TSDC42BNBKInternal model: YSDC-36YSDC-42wall screws(ST6*25mm).(36":7.26lbs(3.3kg),42":7.7lbs(3.5kg).5Make sure the ceiling is securely installed so that it will be able to support at least the fan weight.)WARNING: 2. CONNECT TO DC 12V POWER ONLY.Hang the roller of thesafety cable on to thesafety cable hook.ceiling1. SUPPORT DIRECTLY FROM BUILDING STRUCTURE.410TSDC36BNWH 410TSDC42BNBKInternal model: YSDC-36YSDC-42brackets with blade screws Secure the blades to the blade (3/16"*12mm) and washers.Remove screws and washers fromturn disk first and then tighten bladebrackets to turn disk using turn diskscrews.Attach one metal washer onto the shaft of the fan motor, Lift turn disk and align the hole of turn disk onto the shaft of the motor and then insert it. One hand hold the turn disk, secure the e-clip onto theslot from the shaft of the motor to free your hands. Finally,tighten the turn disk by theshaft nut.6Remove the blade screws and fiber.Remove screws and washers fromturn disk first and then tighten bladebrackets to turn disk using turn diskscrews.Change Blades Installation:There are three mating holes on the housing. Lift housing and rotate it until the hole of housing then install three screws(3/16"*12mm)secure the housing to the fan motor 410TSDC36BNWH 410TSDC42BNBK Internal model: YSDC-36YSDC-42match the hole of fan motor assembly, into the mating holes and tighten in assembly.71. Install the wall switch in a junction box as shown.Turn on the electric power at the main fuse or circuit breaker box.2. The DC12V positive and negative wire need to be protectedbefore it through the opening to reduce the chance of wiredamage.3. Wire connection:a. Connect the white (positive) wire from junction box to thewhite (positive) wire from the wall switch with a wire connector.b. Connect the blue (negative) wire from junction box to theblue (negative) wire from the wall switch with a wire connector.c. Connect the red (positive) wire from wall switch to the batterypositive (+) wire with a wire connector.d. Connect the black (negative) wire from wall switch to thebattery negative (-) wire with a wire connector.e. Carefully push the wire connection points into wall outlet box.f. There are four slots on the wall switch and four studs on the wall switch cover. Install two studs on the bottom of the wallswitch cover into two slots on the wall switch and then pushwall switch cover until it securely on the wall switch.Warning: 1. Connect to DC 12V Power Only. 2. To reduce the risk of fire, or electric shock, do not use this fan with any other solid-state speed control.Wall Switch Installation:Secure the wall switch with two wall switch screws provided in wall switch.410TSDC36BNWH 410TSDC42BNBKInternal model: YSDC-36YSDC-42Change the obverse blade to the back side,reinstall the screws and fiber.1. If fan does not start: CAUTION: Connect to DC 12V Power Only before turn on the fan.1. Check the main and branch circuit fuses of circuit breakers.2. Turn off electrical power and check all wire connections to fan and wall switch.3. Make sure that the wall switch is in the “on” position.2. Noisy Operation: 1. Make sure all screws in motor housing are snug. (Not over tightened.)2. Make sure the screws which secure the fan blade bracket to the motor are tight.3. Allow “break-in” period of 24 hours. Most noises associated with a new fan will disappear after this period.3. Excessive wobbling: All blades are weighted and grouped by weight. Natural woods vary in density which could cause the fan to wobble even though all blades are weight-matched. The following procedures should eliminate most of the wobble. Check for wobble by following the steps listed below.1. Check that all blades are screwed firmly to blade brackets.2. Check that all blade brackets are tightened securely to motor.3. Make sure that motor are tightened securely to ceiling.4. Check distance between blade tip to blade tip. All measurements should be equal. Loosen and retighten the blades if necessary.5. Check distance from tip of blades to ceiling. Gently bend up or down the blade until all distances are the same.6. If blade wobble is still noticeable, interchange two adjacent (side by side) blades forredistributing the weight.8Troubleshooting Guide 410TSDC36BNWH 410TSDC42BNBKInternal model: YSDC-36YSDC-42FUNCTION OF WALL SWITCH:1. Turn on the power and check operation of fan.2. Press "POWER" button at “—” position to turn on the fan at high speed.3. Press "POWER" button at “o” position to turn off the fan.4. Press “SPEED” button to change fan speed. PRESS SPEEDS One time 100%--High Speed Twice 75%--Medium High Third 50%--Medium Fourth 25%--Low 5. Press "REVERSAL" button to sets direction of fan rotation. a. Turn on the fan at first time without setting, the blades are turning clockwise to create an upward motion, pulling cooler air near the floor up toward the ceiling, forcing warmer air downward, this good for air circulation and suitable for winter. b. Press "REVERSAL" button to sets the fan to turn counterclockwise, which will create a downward motion and a cooling effect. If you can feel cool air blowing down on your skin, then that means the fan is turning counterclockwise, this is suitable for summer.。

三筒烘干机说明书

三筒烘干机说明书三筒烘干机说明书郑州恒锐机器设备有限公司目录一、概述 (1)二、型号说明 (1)三、主要性能及技术参数 (2)四、工作原理 (3)五、结构特点 (4)六、结构组成、工艺图 (6)七、安装与调度 (8)八、维护、检修 (10)九、注意事项 (12)十、其它说明 (13)十一、随设备提供的技术资料 (13)四、工作原理N型内循环式烘干机是通过对单筒烘干机的单一筒体改为套叠在一起的三筒，以缩短烘干机的外形尺寸。

该机工作时，物料和热气流依次进入内中外筒体，在烘干机内作“N”形往复折流后，充分利用热能烘干物料后再卸出。

该烘干机筒体部分由三个筒轴水平放置的内中外套筒组成，中内筒为二锥筒，外筒为直筒，这就使通体的截面得到充分利用，其筒体外形总长度约为相当的单筒的25％－35％，从而大幅度的减少了占地面积和厂房建筑面积。

该机的支撑装置，在高温端和低温端采用活套在外筒上的轮带与托轮支撑，取消了大、小齿轮传动，采用四托轮边缘同步传动，使总体结构紧凑、合理。

为便与磨损件的检修和更换，在烘干机的前后设有封板，用螺栓固定连接。

该机工作时，物料与热气流顺流从内锥筒的小端进入，被扬料板扬起与热气流进行充分的热交换，同时向大端移动。

同理，进入中筒后，物料被勺形扬料板扬起，并均匀地撒落在内锥筒外壁的上部，随筒体慢速回转，物料在环形空间能经历一较长的滞留时间，由中筒锥的小端向大端移动。

最后沿筒壁和中筒外壁上的导料板流向出口端，通过翻板阀卸出，废气由卸料罩上的顶部出口经布袋收尘器收尘后由由引风机通过烟囱排出。

从上述物料的流程可以看出，物料在被一筒内热气流直接烘干的同时，又被相邻筒的热气流间接烘干。

中、内筒里的物料与热气流之间的热交换以辐射、对流传热形式为主，而在外筒内，气体湿度已较大，温度较低，物料撒落在中筒外壁上，使两者的热交换以传导、对流形式为主，从烘干机原理上也是非常合理和科学的，再者，低温段的外筒对高温段的内筒有保温隔热作用，并使设备的总散热面积相对于单筒烘干机减少了50％～60％，外筒表面的温度仅为30-50℃。

安装、运行与维护手册 - 3700 型号 - 重力卸荷阀说明书

Model 3700, API Type OH2 / ISO 13709 1st and 2nd Ed. / API 610 8/9/10/11th Ed. 安装、运行与维护手册
1Leabharlann 目录5.2 卸下联轴罩........................................................................... 33 5.3 检查转动............................................................................. 34 5.4 泵和驱动机连接....................................................................... 34
3 产品说明 ......................................................................................................................................................13 3.1 3700 的一般说明...................................................................... 13 3.2 铭牌信息............................................................................. 14
5 试车、起动、运行和关机 ............................................................................................................................. 32 5.1 启动准备............................................................................. 32

起重设备操作手册 - OZ牌碳钢和不锈钢制动绞盘说明书

OPERATOR’S MANUALCARBON STEEL & STAINLESS STEEL BRAKE WINCHESWorking Loads: 1000 lbs. 1500 lbs. 2000 lbs.Please read the Owner’s Manualcarefully before operatingthe equipment. Keep thismanual nearby theequipment atall times.CARBON STEEL:OZ1000BWOZ1500BWOZ2000BWSTAINLESS STEEL:OZ1000BWSSOZ1500BWSSOZ2000BWSSpg.1P.O. Box 845, Winona, MN 55987Phone (800) 749-1064(507) 474-6250Fax (507) 452-5217 ***************************Table of ContentsPg. 3 . . . . . . . . . . . . . . . . . . . . . . . . . WarrantyPg. 4 . . . . . . . . . . . . . . . . . . . . . . . . . Important Information and PrecautionsPg. 5 . . . . . . . . . . . . . . . . . . . . . . . . . Warnings and PrecautionsPg. 6 . . . . . . . . . . . . . . . . . . . . . . . . . Installing the WinchPg. 7 . . . . . . . . . . . . . . . . . . . . . . . . . Installing the RopePg. 8 . . . . . . . . . . . . . . . . . . . . . . . . . Concept of Operation / Pre-OperationPg. 9 . . . . . . . . . . . . . . . . . . . . . . . . . InspectionPg. 10 . . . . . . . . . . . . . . . . . . . . . . . . Inspection ChartPg. 11 . . . . . . . . . . . . . . . . . . . . . . . . Repair of Winch / Trouble Shooting Chart Pg. 12 . . . . . . . . . . . . . . . . . . . . . . . . Specifications / Performance Characteristics Pg. 13 . . . . . . . . . . . . . . . . . . . . . . . . MountingPg. 14 . . . . . . . . . . . . . . . . . . . . . . . . PartsPg. 15 . . . . . . . . . . . . . . . . . . . . . . . . Parts / Service Notespg.2WarrantyAll OZ Lifting Products LLC. are guaranteed to be free of defects in materials and workmanship for one year from the date of shipment.This does not apply to any product showing signs of misuse, overloading, alteration, improper maintenance or negligence. Normal wear and tear of moving parts including brake discs, wire rope, and other wear components are excluded from this warranty. This warranty does not cover any costs involving removal of this product, lost time, or any other incidental or consequential damages or costs resulting from the claimed defects.If any of our products fail during the first year of operating due to defective materials or workmanship, it will be repaired or replaced at the discretion of OZ Lifting Products LLC. The product will then be returned to the customer free of charge. If no defect is found, the customer will be responsible for return shipping costs.Upon repair, the product will be covered by the warranty for the remainder of the original warranty period. OZ Lifting will not be held liable for injuries to persons or property, death, incidental, consequential, or contingent damages, whether negligent or deliberate, arising from the use of the product. It is the sole responsibility of the owner to install and operate the product properly and safely.This is OZ Lifting Product’s only written warranty. This warranty is in lieu of all other warranties implied by law such as merchantability and fitness. The sale of products of OZ lifting Products LLC. under any other warranty or guarantee, expressed or implied, is not authorized.Note: OZ lifting Products LLC. has the right to alter the design or discontinue the production of any product without prior notice.Warranty PolicyAny product for which there is a warranty claim must be returned prepaid to an authorized OZ Lifting warranty depot along with proof of purchase.For more information please contact:P.O. Box 845, Winona, MN 55987Phone (800) 749-1064(507) 474-6250Fax (507) 452-5217***************************pg.3Important Information and Precautions The information in this manual should be used only for the OZ Lifting Brake Winches. This manual contains general instructions dealing with the normal installation, operation, and maintenance of the products described herein. The information provided should not be expected to prepare the user for all possible circumstances.This product should not be installed, operated, or maintained by any person who has not read all the contents of these instructions. Failure to read and comply with these instructions, warnings, or limitations noted might result in bodily injury, death, or property damage. Contact the distributor for further explanation if information is not fully understood.It is the responsibility of the owner/user to install, test, maintain, and operate these products in accordance with OSHA, regulations, other federal, state, and local regulations, and ANSI standards.Only trained and qualified personnel shall operate and maintain this equipment.Maintain RecordsSchedule and maintain records of regular inspection and maintenance of the product in compliance with ANSI standards. Record your Brake Winch serial number and purchase date on the front cover of this manual to allow for easier referencing.PrecautionsDo not use OZ Lifting Products in conjunction with other equipment unless the system designer, manufacturer, installer, or user has put the necessary safety devices in place. Modifications to upgrade or alter these products should only be authorized by the original manufacturer.Brake Winches should be used for holding loads only within their load ratings.These Brake Winches meet or exceed the following standards:CEANSI B30.21ANSI B30.16pg.4Warnings and PrecautionsFailure to read and comply with the following warnings may result in a hazardous situation that could lead to death, serious injury, or property damage. Keep this manual near the equipment at all times. Do not remove, alter, or obscure the labels attached to the winch. Contact OZ Lifting Prod-ucts LLC. for replacement manuals and labels.Do Not operate until all personnel are warned or cleared from the area.Do Not lift people or lift loads over people.Do Not allow people anywhere near the potential path of wire rope that could snap.Do Not allow people or situations to become distractions while operating the winch.Do Not alter the equipment.Do Not operate a damaged or malfunctioning product.Do Not leave a suspended load unattended without taking proper precautions.Do Not operate without verifying wire rope is installed securely to winch drum.Do Not operate with any power other than manual.Do Not operate without a minimum of 4 anchor wraps of wire rope on the drum.Do Not get close to moving parts of the equipment including drum, gears, wire rope.Do Not lift more than the designated load rating of the winch or other system parts.Do Not use more than one winch to lift a load, unless the system is so designed.Do Not lift or pull loads on an incline without a brake installed on the equipment.Do Not use if the load is not suspended vertically.Do Not use the equipment if guards are removed or improperly installed.Do Not allow the load to swing or jerk and avoid shock loads by operating smoothly.Do Not weld on the lifted load.Do Not secure load by wrapping wire rope around it, instead use rigging connectors.pg.5pg.6Installing the WinchChoosing a location • Have a qualified professional confirm that the foundation complies with local codes, is rigid and level, and will support the winch under all load conditions.• Avoid areas with corrosives, flammables, combustibles, explosives, and other potentiallydamaging materials.• Avoid areas defined as hazardous by the National Electric Code, unless proper authorization is received. • Situate the winch where the operator can avoid the load area and the potential path of snappingwire rope.• Situate the winch in a place where it can be seen throughout the whole operation.• Avoid areas with potential interferences such as traffic and obstacles.• Ensure the winch is easily accessible for operation and routine maintenance.Installation 1. Use a fleet angle between ½ and 1 ½ degrees.• This angle permits the rope to spool more evenly onto the drum, reducing harm to the wire rope.2. Do Not weld the winch frame to the foundation.• Doing so would invalidate the warranty.• Contact OZ Lifting Products LLC. for more information.3. Fasten the winch firmly to the foundation.• For standard products use 3/8 inch coarse thread fasteners of at least grade 5 with a torque of 30 ft. lb. without lubrication. Use safe engineering practices to assure that the mounting holes are attached firmly to a solid foundation that will support the winch and load in all situations.4. Install the Sheave Roller or Roller Guide.• It is recommended to use a sheave roller or roller guide to direct the wire rope onto the drum.• Follow recommendations of the sheave manufacturer on installation and use.• Install sheaves, tracks, and other equipment so that they stay firmly in place in all load situations.• Select sheaves of a suitable diameter to lessen damage to the wire rope.Maintain Fleet Angle 1. Wire rope moves over sheave or through the roller guide. Situate sheave or guide an acceptable distance from the drum (distance “A”)2. Wire rope moves directly to the load. Use tracks or guide rails to prevent sideway movements that canstress and harm the drum flange.Tracks or Smooth drumInstalling the Wire Rope• Ensure the wire rope spools correctly and is attached firmly to the winch drum to prevent release of the load.• Wear protective clothing when working with the wire rope.• Prevent damage to the rope by keeping it clean and not allowing it to pass through dirt or debris.Consider the following information when choosingthe proper wire rope.• Lay of the rope should match the winding direction of the drum.• Breaking strength should be at least 3 times greater than the largest load when pulling on a horizontal surface. 5 times that if loads are lifted or pulled at inclines.• OZ Lifting advises a 7 x 19 galvanized aircraft cable be used for diameters up to 5/16 inch.• Contact a wire rope supplier for further assistance.Installation1. Use a flange clip or quick disconnect anchor to anchor the rope to the drum.a. Flange Clip Anchori. Thread the end of the wire rope through the flange hole.ii. Connect the carriage bolt and wrap the wire rope around it.iii. Fit the clip on so that it holds the wire rope with its curves.iv. Tighten the jam nut on until it flattens the wire rope against the drum flange.b. Quick Disconnect Anchori. Insert the End Stop through the center hole in the drum flange.ii. Pull the wire rope and the end stop into the slot.2. Spool the rope onto the drum by turning the handle clockwise.a. If the rope unwinds it needs to be re-installed correctly before continuing.3. Keep the rope under tension, and using the winch, spool four full wraps of rope onto the drum.pg.7Drum End ViewDrum End ViewConcept of Operation1. Assure that the total force needed to lift the load does not surpass the load rating of the winch.2. Follow all recommended maintenance and inspections to monitor for any damage that could contribute additional weight to the equipment.3. A disc brake should be used if loads will be lifted or pulled on an incline.4. Be aware of variables affecting performance ratings of the equipment.a. Loose spooling and overlapping of the wire rope affects drum capacity. Actual drum capacities are25-30% less than those listed in performance tables.b. As rope spools around the drum, the force needed to lift the load increases and the load rating of the winch decreases.i. Performance table values are based on a drum without rope and with a maximum handle length.ii. The load rating is the greatest pull that can be applied on new equipment without damage or otherfactors affecting its operation.5. Maintain the correct fleet angle and keep sufficient tension on the rope so it winds evenly.6. Take in consideration the factors that can affect the duty rating.a. Equipment Maintenancei. Perform preventative maintenance and inspections to check for damage or defects on a regular basis. ii. Keep the winch clean and free of debris.b. Environmental Conditionsi. Avoid exposure to extreme temperatures, excessive dirt, wet conditions, flammables, combustibles,explosives, and other potentially damaging materials.c. Loading Conditionsi. Do not exceed maximum load ratings or shock load.d. Frequency of Usei. Monitor the equipment’s parts often as frequency of use increases. More use will increase wear and shorten the life span of the parts.Pre-Operation• Be certain that no hazards will interfere with any part of operation and the load will have adequate clear space to be moved.• Complete all recommended inspections and any maintenance that are due.• Assure that the operator is well rested, has up to date training on the equipment, and has proper personal protective equipment including hardhat, safety shoes and eyewear, work gloves, and no loose fittingclothing or jewelry.• Know the total force of the load so that the load rating of the equipment is not surpassed.pg.8InspectionsIn order to maintain quality operation of the product, a regular inspection schedule should be set up by each operator. All inspections should be reported and maintained in a dated record log. These records should be available to all personnel involved with the product, and should be made available to OZ Lifting Products LLC. when a warranty issue is in question.DefinitionsThe following definitions are from the ANSI/ASME B30.21 and will be used in the inspections procedure that follows.Designated Person- a person who is selected or assigned as being competent to perform specific duties to which they are assigned.Qualified Person- a person that by possession of a recognized degree or certificate of professional standing, or through extensive knowledge, training, and experience, has successfully demonstrated they are able to resolve problems relating to the subject matter and work.Normal Service- service that involves operation with randomly distributed loads within the rated load limit, or uniform loads less than 65% of rated load for not more than 15% of the time.Heavy Service- service that involves operation within the rated load limit and exceeds normal service.Severe Service- service that involves normal or heavy service with abnormal operating conditions.Inspection ClassificationsFrequent Inspections- The operator or designated person performs frequent inspections by doing a visual examination and by listening for unusual sounds during operation. These inspections are usually performed before each operation, every few hours in operation, and if problems arise.Periodic Inspections- A designated person performs periodic inspections, which are more detailed inspection, by doing visual examinations of internal and external conditions. These inspections are done on the following schedule:*Normal Service- Semi-annually*Heavy and Severe Service- Quarterly*Also perform following storage and return to use, if a possible shock load has occurred, and if operation issues arise.Label Equipment as “Out of Service” if damaged or maintenance is required• Discontinue use of wire rope and equipment if damage or overloading occurs.pg.9Take note of the following regarding inspections.• Brakes require more than audible and visual inspection. Check daily by operating with and without a load, stopping at various positions to ensure safe operation. If the load coasts or creeps contact the factory for friction disc replacements.• Proper inspection may require disassembly of some parts. Contact the factory before doing so or theapplicable warranty may be voided.• For wire rope inspections please contact the specific manufacturer of the rope. The inspection provided in the chart below is for a general inspection only and is in no way the complete inspection required.• Before operation assure all deficiencies on the inspection chart are resolved and inspections are up todate. Refer to troubleshooting chart for further assistance.Inspection ChartFrequent Inspection (F) and Periodic Inspection (P)Location Check For F P General Paint chipping or excessive wear XDamage, cracks, rust, dents excess wear, or corrosion.XUnusual sounds XSmooth load movements XWinch lubricated XSigns of overloading (cracks, dents, or damage)XProper function when operated with a load equal to the load rating X Foundation Good condition/Supports the winch under all conditions XCracks, corrosion, damage X Brake Assembly Ratchet pawl clicks firmly as handle is turned clockwise XProper operation XCorrosion, cracks, damage, or wear X Fasteners Firmly installed XProperly tightened XStripped threads, bent, or damage (check by removing winch from the foundation)X Gears, bearings, shafts Excess wear, cracks, corrosion, or damage XWell lubricated X Handle Rotates freely in both directions XEnd Connections Corrosion, excess wear, rust, or damage XAttached firmly X Drum Excess wear or distortion of anchor hole XExcess movement due to misaligned gears, bearings, shafts (check by moving the drum by hand)X Load Hook Bent, twisted or damaged XHook latch doesn’t close when released XSecurely attached to wire rope with no fraying or damage to the rope X Frame Bent, cracks, or damage (signs of overloading)X Wire rope Installed correctly XWound tightly and evenly on drum XNo visible damage to entire rope X Labels Not been removed, altered, or obscured (Contact factory for replacements)Xpg.10Repair of the WinchAll repairs must have factory authorization. Contact OZ Lifting LLC. to prevent voiding of the warranty and potential damage to the winch.Perform recommended inspections to identify which parts should be replaced.• Only use OZ Lifting Products LLC. replacement parts.• Contact the local OZ Lifting Products LLC. dealer for replacement parts. Please have the serial number and part number and description available when calling.Protect the winch from damage and corrosion by monitoring for paint chipping or excess wear.• Refinish any problem areas by removing paint to the bare metal, cleaning the area well and repainting with a high quality primer and finish coat.Troubleshooting ChartContact OZ Lifting Products LLC. if disassembly of the winch or brake is required. The warranty will be voided if this is not done.Problem Possible Cause CorrectionBrake distance too long Discs are worn, damaged, or over lubricated ReplaceDisc brake ratchet pawl damaged or worn ReplaceExcess wear on gears or bearings Overloaded Reduce loadImproper lubrication RelubricateDrum not turning (handle functioning okay)Damaged or loose spring pins RepairGears broke, stripped, or loose Repair/ReplaceDifficulty turning handle or not turning at all Heavy load Reduce loadDisc brake damaged or locked RepairGears or bearings damaged or locked RepairSpring pins loose or damaged RepairHigh pitched squeak Improper lubrication RelubricateGrinding noise Dirty lubrication Clean and relubricateDirty brakes or gears CleanBroken gears or bearings ReplaceRattling noise Loose bolts, screws, fasteners TightenNo clicking noise in brake Ratchet not properly installed Install correctlyRatchet pawl damaged or worn ReplaceUneven brake clicking Broken gear tooth ReplaceDull brake clicking Dirty or damaged spring or ratchet pawl Clean or repairExcess wear of brake ratchet pawl, spring, or gear Replacepg.11pg.12SpecificationsABLCMKFEDHIJGPerformance Characteristics*Actual drum capacities may be 25-30% less, due to nonuniform winding. Wire rope tension will also affect drum capacity.pg.13MountingOZ1000BW OZ1000BWSSN= 1.73”O= 3.46”P= 1.30”Q= 5.43”R= 0.94”S= 0.79”T= 1.06”U= 1.57”V= 0.41”W= 0.41” x 1.65”X= 0.51”OZ2000BW OZ2000B WSSN= 2.50”O= 5.00”P= 6.36”Q= 9.45”R= 1.00”S= 1.50”T= 1.60”U= 3.00”V= 0.39”W= 0.39” x 1.77”X= 4.70”Y= 0.39”x0.78”Z= 0.51”OZ1500BW OZ1500B WSSN= 2.10”O= 4.20”P= 5.28”Q= 7.56”R= 0.72”S= 1.38”T= 0.79”U= 2.76”V= 0.39”W= 0.39” x 2.17”X= 4.49”Y= 1.14”Z= 1.14”pg.14Parts1. Nut (1)2. Screw (1)3. Drum (1)4. Cover (1)5. Mounting Base (1)6. Snap Ring (2)7. Ratchet Pawl (2)8. Retaining Ring (2)9. Shaft (1)10. Rachet (1)1. Nut (1)2. Screw (1)3. Drum (1)4. Cover (1)5. Mounting Base (1)6. Snap Ring (2)7. Ratchet Pawl (1)8. Retaining Ring (1)9. Bolt (1)10. Friction Brake (2)11. Friction Brake (2)12. Clip (1)13. Shaft (1)14. Cover Part (1)15. Washer 6 (5)16. Bolt (5)17. Nut (1)18. Washer (1)19. Support Rod (1)20. Nut (1)11. Rachet (1)12. Clip (1)13. Shaft (1)14. Cover Part (1)15. Washer (4)16. Bolt (2)17. Bolt (2)18. Nut (1)19. Washer (1)20. Retaining Ring (2)21. Retaining Ring (2)22. Washer (2)23. Gear (1)24. Clip (1)25. Bolt (1)26. Washer (1)27. Retaining Ring (1)28. Handle (1)29. Washer (1)30. Nut (1)40. Wire Rope Clip21. Washer (2)22. Nut (2)23. Gear (1)24. Clip (1)25. Washer (1)26. Retaining Ring (1)27. Handle (1)28. Washer (1)29. Nut (1)40. Wire Rope Cip (1)OZ1500BW - OZ1500BWSSOZ1000BW - OZ1000BWSSService Notespg.15Parts1. Nut (1)2. Screw (1)3. Drum (1)4. Cover (1)5. Nut (1)6. Munting Base (1)7. Snap Ring (2)8. Ratchet Pawl (2)9. Retaining Ring (2)10. Bolt (2)11. Shaft (1)12. Rataining Ring (1)13. Washer (1)14. Gear (1)15. Gear (1)16. Shaft (1)17. Shaft (1)18. Cover Part (1)19. Washer (6)20. Bolt (3)21. Washer (1)22. Retaining Ring (1)23. Handle (1)24. Washer (1)25. Nut (1)26. Nut (1)27. Washer (1)28. Bolt (1)29. Washer (1)30. Support Pipe (1)31. Retaining Ring (2)32. Washer (2)33. Support Rod (1)34. Gear (1)35. Clip (1)36. Friction Brake (2)37. Ratchet (1)38. Clip (1)39. Bolt (1)40. Wire Rope Clip (1)OZ2000BW - OZ2000BWSSP.O. Box 845, Winona, MN 55987Phone (800) 749-1064(507) 474-6250Fax (507) 452-5217 ***************************Rev. 10/04/12。

GPG13 'M' 系列包装气机说明书

REPAIR PARTS®nufacturing Company, L.P. ◊5151 San Felipe, Suite 500 ◊RP-578AThis manual is to be used by qualified technicians only.This manual replaces RP-578.November 2014GPG13 "M" Series Package Gas Unit© 2009,2014 Goodman Company, L.P. ◊ 5151 San Felipe St., Suite 500 ◊ Houston, TX 77056GPG1324045M41AA GPG1324070M41AA GPG1330045M41AA GPG1330070M41AA GPG1336045M41AA GPG1336070M41AA GPG1336090M41AA GPG1336090M43AA GPG1342070M41AA GPG1342090M41AA GPG1348070M41AA GPG1348090M41AA GPG1348090M43AA GPG1348115M41AA GPG1360090M41AA GPG1360090M43AA GPG1360115M41AA GPG1360140M41AA GPG1360140M43AAImportant Information For assistance within the U.S.A. contact:For assistance outside the U.S.A. contact:IndexFunctional Parts List Per request from Service Parts Engineer: removed 0231K00039 from GPG1348115M41AA.Illustration and Parts......................................................................................................................................................................................................Views shown are for parts illustrations only, not servicing proceduresAR - As Required NA - Not Available NS - Not Shown00000000 - See NoteQTY - Quantity Example (QTY 3) (If Quantity not shown, Quantity = 1)M - Model Example (M1) (If M Code not shown, then part is used on all Models)Text Codes:ExampleM1 - Model#1 M2 - Model#2 M3 - Model#3Expanded Model Nomenclature:Goodman Company, L.P. is not responsible for personal injury or property damage resulting from improper service. Review all service information before beginning repairs.Warranty service must be performed by an authorized technician, using authorized factory parts. If service is required after the warranty expires, Goodman Company, L.P. also recommends contacting an authorized technician and using authorized factory parts.Goodman Company, L.P. reserves the right to discontinue, or change at any time, specifications or designs without notice or without incurring obligations. 2Consumer Affairs Department Goodman Company, L.P.7401 Security Way Houston, Texas 77040877-254-4729-Telephone 713-863-2382-FacsimileInternational DivisionGoodman Company, L.P.7401 Security Way Houston, Texas 77040713-861-2500-Telephone 713-863-2382-Facsimile 4 - 153RP-578AFunctional Parts PartNo:Description:B137075124V RELAY (M11, M12, M13, M14, M15, M16,M17, M18, M19)0131M00522BLOWER MOTOR - 1 HP PROGRAMMEDSELEC (M15, M16, M17, M18, M19)0131M00527BLOWER MOTOR - 1 HP PROGRAMMEDSELEC (M11, M12, M13, M14)11091202BLOWER MOTOR 1/3 HP, 3 SP, 6 PL (M3, M4) 11091203BLOWER MOTOR 1/3 HP, 3 SP, 6 PL (M5,M6, M7, M8, M9, M10)11091207BLOWER MOTOR 1/4 HP, 3 SP, 8 PL (M1, M2) CAP100000370LA CAPACITOR 10/370V (M1, M2, M3, M4, M5,M6, M7, M8, M9, M10)CAP050350440CS CAPACITOR 5/35/440V (M1, M2, M3, M4)CAP050000370LA CAPACITOR 5/370V (M8, M13, M16, M19) CAP050450440CT CAPACITOR 5/45/440V/DUAL RD (M5, M6,M7, M9, M10, M11, M12, M14)CAP050700440CT CAPACITOR 5/70/440V/DUAL RD (M15, M17,M18)ZP31K5EPFV130COMPRESSOR 31100, 208/230/60/1 (M5, M6,M7)ZP31K5ETF5130COMPRESSOR 31200, 200/230/60/3 (M8)ZP34K5EPFV130COMPRESSOR 34500, 208/230/60/1 (M9, M10) ZP39K5ETF5130COMPRESSOR 39000, 200/230/60/3 (M13)ZP39K5EPFV130COMPRESSOR 39000, 208/230/60/1 (M11,M12, M14)ZP51K5EPFV130COMPRESSOR 51000, 208/230/60/1 (M15,M17, M18)ZP51K5ETF5130COMPRESSOR 51000, 208/230/60/3 (M16,M19)760001-2001-20COMPRESSOR, BRISTOL (M1, M2)760005-2001-20COMPRESSOR, BRISTOL (M3, M4)0131M00061COND MOTOR 1/4 HP, 1 SP, 8 PL (M1, M2,M5, M6, M7, M8)0131M00429COND MOTOR 1/4 HP, 1 SP,6 PL (M3, M4,M9, M10, M11, M12, M13, M14, M15, M16,M17, M18, M19)CONT1P025024V CONTACTOR 25 AMP, 1P, 24V (M1, M2, M3,M4, M5, M6, M7)CONT3P025024V CONTACTOR 25 AMP, 3P, 24V (M8, M13,M16, M19)CONT1P030024V CONTACTOR 30 AMP, 1P, 24V (M9, M10,M11, M12, M14, M15, M17, M18)0130M00018CUT-OUT SWITCH, HIGH PRESSURE0130F00010FLAME SENSORB1282628GAS VALVE (36G) (M1, M2, M3, M4, M5, M6,M7, M8, M9, M10, M11, M12, M13, M14, M15,M16, M17)0131G00000P ID BLOWERPCBAG123IGNITION BOARD, DSI INTEGRATED (M1,M2, M3, M4, M5, M6, M7, M9, M10, M11, M12,M14, M15, M17, M18)0130F00014IGNITOR10728342LIMIT SWITCH (M1, M2, M3, M4)10728343LIMIT SWITCH (M5, M6, M7, M18, M19) 10728344LIMIT SWITCH (M8, M9, M10, M11, M12, M13,M14, M15, M16, M17)10123529MANUAL RESET LIMIT-GREEN10716003ORIFICE (QTY A/R)0130M00138TRANSFORMER 208/230, 24V Expanded Model NomenclatureM1 - GPG1324045M41AAM2 - GPG1324070M41AAM3 - GPG1330045M41AAM4 - GPG1330070M41AAM5 - GPG1336045M41AAM6 - GPG1336070M41AAM7 - GPG1336090M41AAM8 - GPG1336090M43AAM9 - GPG1342070M41AAM10 - GPG1342090M41AAM11 - GPG1348070M41AAM12 - GPG1348090M41AAM13 - GPG1348090M43AAM14 - GPG1348115M41AAM15 - GPG1360090M41AAM16 - GPG1360090M43AAM17 - GPG1360115M41AAM18 - GPG1360140M41AAM19 - GPG1360140M43AA3RP-578A Top Panel/Fan/Cabinet 4RP-578ATop Panel/Fan/CabinetRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:FAN BLADE (M1, M2)0150M0001611FAN BLADE (M3, M4)B108677511FAN BLADE SWEPT-WING (M5, M6, M7, M8)0150G0000211FAN BLADE SWEPT-WING (M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)0150G0000311COND MOTOR 1/4 HP, 1 SP, 8 PL (M1, M2, M5, M6, M7, M8)0131M0006121COND MOTOR 1/4 HP, 1 SP,6 PL (M3, M4, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)0131M0042921FAN GRILLE 0152G0000331TOP PANEL0121G00156PDG 41SMALL SCREW (QTY 6)M022181751ACORN NUT 5/16 HEX BLACK (QTY 4)0163M00006P 61BLOWER DOOR 32" (M1, M2, M3, M4, M5, M6, M7)20464801PDG 71BLOWER DOOR 40" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20464806PDG 71EVAP/CONTROL DOOR 32" (M1, M2, M3, M4, M5, M6, M7)20464802PDG 81EVAP/CONTROL DOOR 40" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20464807PDG 81DOOR-HT EXCHANGE 32 (M1, M2, M3, M4, M5, M6, M7)0121G00526DG 91DOOR-HT EXCHANGE 38 (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)0121G00527DG 91COMPRESSOR DOOR 32" (M1, M2, M3, M4, M5, M6, M7)20464804PDG 101COMPRESSOR DOOR 40" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20464809PDG 101LOUVERED PANEL, COND SIDE 32" (M1, M2, M3, M4, M5, M6, M7)20467701PDG 111LOUVERED PANEL, COND SIDE 40" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20467702PDG111UTILITY PANEL 32" (M1, M2, M3, M4, M5, M6, M7)20466101PDG 121UTILITY PANEL 40" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20466102PDG 121PNL, DUCT, GAS 32.5" (M1, M2, M3, M4, M5, M6, M7)0121G00442DG 131PNL, DUCT, GAS 40" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)0121G00443DG 131SIDE SUPPORT POST (M1, M2, M3, M4, M5, M6, M7)0121G00460141SIDE SUPPORT POST (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)0121G00462141LOUVERED PANEL, COND SIDE 32" (M1, M2, M3, M4, M5, M6, M7)20464401PDG 161LOUVERED PANEL, COND SIDE 40" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20464402PDG161CORNER POST-COMP END 32" (M5, M6, M7)20464201PDG 251CORNER POST-COMP END 40" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20464202PDG 251CORNER POST-HAIRPIN END 32" (M5, M6, M7)20464301PDG 261CORNER POST-HAIRPIN END 40" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20464302PDG 261FLUE HOOD (QTY 2)0121G00323NS FLUE HOOD ASSY0270G00131NSImage 1:FLUE HOOD-LOWER 0121G00190NS GAS LINE GROMMET B1910012NS GOODMAN LABEL B10259251NS PVC CONDUIT 8.25"177********FNSExpanded Model Nomenclature M1 - GPG1324045M41AA M2 - GPG1324070M41AA M3 - GPG1330045M41AA M4 - GPG1330070M41AA M5 - GPG1336045M41AA M6 - GPG1336070M41AA M7 - GPG1336090M41AA M8 - GPG1336090M43AA M9 - GPG1342070M41AA M10 - GPG1342090M41AA M11 - GPG1348070M41AA M12 - GPG1348090M41AA M13 - GPG1348090M43AA M14 - GPG1348115M41AA M15 - GPG1360090M41AA M16 - GPG1360090M43AA M17 - GPG1360115M41AA M18 - GPG1360140M41AA M19 - GPG1360140M43AA5RP-578A Partition Panels 6RP-578APartition PanelsRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:BLOWER DIVIDER (M1, M2, M3, M4)2046530571BLOWER DIVIDER (M8, M9, M10)2046530671BLOWER DIVIDER 32" 10 X 9 (M5, M6, M7)2046530471BLOWER DIVIDER-38 (M11, M12, M13, M14, M15, M16, M17, M18, M19)2046530271FILLER PANEL, HEAT EXCHANGER 32" (M1, M2, M3, M4, M5, M6, M7)20465201101EVAP/HEAT EXCHANGER DIVIDER 32" (M1, M2, M3, M4, M5, M6, M7)20465501121EVAP/HEAT EXCHANGER DIVIDER 38" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20465502121FAN PARTITION SHELF20465701131FAN SURROUND 32" (M1, M2, M3, M4, M5, M6, M7)20465801141BACK DUCT COVER 40" (M8, M13, M16, M19)20464502PDG 161EVAP/BASEPAN BLOCK 32" (M1, M2, M3, M4, M5, M6, M7)20463802221EVAP/BASEPAN BLOCK 40" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20463801221Expanded Model Nomenclature M1 - GPG1324045M41AA M2 - GPG1324070M41AA M3 - GPG1330045M41AA M4 - GPG1330070M41AA M5 - GPG1336045M41AA M6 - GPG1336070M41AA M7 - GPG1336090M41AA M8 - GPG1336090M43AA M9 - GPG1342070M41AA M10 - GPG1342090M41AA M11 - GPG1348070M41AA M12 - GPG1348090M41AA M13 - GPG1348090M43AA M14 - GPG1348115M41AA M15 - GPG1360090M41AA M16 - GPG1360090M43AA M17 - GPG1360115M41AA M18 - GPG1360140M41AA M19 - GPG1360140M43AA7RP-578A Basepan/Blower Assembly 8RP-578ABasepan/Blower AssemblyRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:TC SCREW (M1, M2, M3, M4, M5, M6, M7, M8, M9, M10)M025055811TC SCREW 1.25" (M11, M12, M13, M14, M15, M16, M17, M18, M19)M025056511BLOWER WHEEL (M5, M6, M7)D672330341BLOWER WHEEL (M8, M9, M10)D672330641BLOWER WHEEL 10 X 8 (M3, M4)B136801641BLOWER WHEEL 10 X 8 (M1, M2)B136805841BLOWER MOTOR 1/3 HP, 3 SP, 6 PL (M3, M4)1109120251BLOWER MOTOR 1/3 HP, 3 SP, 6 PL (M5, M6, M7, M8, M9, M10)1109120351BLOWER MOTOR 1/4 HP, 3 SP, 8 PL (M1, M2)1109120751BLOWER HOUSING ASSY 10 X 10 (M8, M9, M10)0271F0005791BLOWER HOUSING ASSY 10 X 8 (M1, M2)0271F00001P 91BLOWER HOUSING ASSY 10 X 8 (M3, M4)0271G0002591BLOWER HOUSING ASSY 10 X 9 (M5, M6, M7)0271G0002491BLOWER BLOCK-OFF (M5, M6, M7)764742101BLOWER BLOCK-OFF 10 X 10 (M8, M9, M10)764741101BLOWER BLOCK-OFF 10 X 8 (M1, M2, M3, M4)764740101BLOWER CUT-OFF (M11, M12, M13, M14, M15, M16, M17, M18, M19)1864703F 101AUXILIARY LIMIT, AUTO RESET (M3, M4, M5, M6, M7, M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20269903131AUXILIARY LIMIT BRACKET (M3, M4, M5, M6, M7, M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)2509503F151GROMMET, 26TAL F/TORSIN FLEX (M8, M9, M10)B1392143NS MACHINE SCREW HWH 1/4-20 X 1-1/2 BZ (M11, M12, M13, M14, M15, M16, M17, M18, M19)B1393323NSImage 2:MOTOR MOUNT BAND (M11, M12, M13, M14, M15, M16, M17, M18, M19)0121M0003822MOTOR MOUNT ARM (M11, M12, M13, M14, M15, M16, M17, M18, M19)B137685732BLOWER HOUSING ASSY 11 X 10 (M11, M12, M13, M14, M15, M16, M17, M18, M19)253930972SINGLE COVER, DOWN DISCHARGE (M11, M12, M13, M14, M15, M16, M17, M18, M19)0121G0014892CAPACITOR 10/370V (M1, M2, M3, M4, M5, M6, M7, M8, M9, M10)CAP100000370LA 112BLOWER MOTOR - 1 HP PROGRAMMED SELEC (M15, M16, M17, M18, M19)0131M00522122BLOWER MOTOR - 1 HP PROGRAMMED SELEC (M11, M12, M13, M14)0131M0052712211 X 10 BLOWER MOUNTING (M11, M12, M13, M14, M15, M16, M17, M18, M19)2046370114211 X 10 BLOWER SUPPORT LRG (M11, M12, M13, M14, M15, M16, M17, M18, M19)4322801162CAPACITOR STRAP (M1, M2, M3, M4, M5, M6, M7, M9, M10, M11, M12, M14, M15, M17, M18)20520901172BASEPAN, PACKAGE0121G00444272BLOWER WHEEL 11 X 10 (M11, M12, M13, M14, M15, M16, M17, M18, M19)B1368000NS CAPACITOR BOOT (M1, M2, M3, M4, M5, M6, M7, M8, M9, M10)B821700NSImage 2:LOCKNUT, NYLON, INSERT 1/4, 20 (M11, M12, M13, M14, M15, M16, M17, M18, M19)B1393800NSExpanded Model Nomenclature M1 - GPG1324045M41AA M2 - GPG1324070M41AA M3 - GPG1330045M41AA M4 - GPG1330070M41AA M5 - GPG1336045M41AA M6 - GPG1336070M41AA M7 - GPG1336090M41AA M8 - GPG1336090M43AA M9 - GPG1342070M41AA M10 - GPG1342090M41AA M11 - GPG1348070M41AA M12 - GPG1348090M41AA M13 - GPG1348090M43AA M14 - GPG1348115M41AA M15 - GPG1360090M41AA M16 - GPG1360090M43AA M17 - GPG1360115M41AA M18 - GPG1360140M41AA M19 - GPG1360140M43AA9RP-578A Compressor/Tubing Assembly 10RP-578ACompressor/Tubing AssemblyRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:COMPRESSOR 31100, 208/230/60/1 (M5, M6, M7)ZP31K5EPFV13011COMPRESSOR 31200, 200/230/60/3 (M8)ZP31K5ETF513011COMPRESSOR 34500, 208/230/60/1 (M9, M10)ZP34K5EPFV13011COMPRESSOR 39000, 200/230/60/3 (M13)ZP39K5ETF513011COMPRESSOR 39000, 208/230/60/1 (M11, M12, M14)ZP39K5EPFV13011COMPRESSOR 51000, 208/230/60/1 (M15, M17, M18)ZP51K5EPFV13011COMPRESSOR 51000, 208/230/60/3 (M16, M19)ZP51K5ETF513011COMPRESSOR, BRISTOL (M1, M2)760001-2001-2011COMPRESSOR, BRISTOL (M3, M4)760005-2001-2011ACCESS FITTING (M1, M2)B137331541EVAP COIL TUBING ASSY (M11, M12, M13, M14)0202G0028261EVAP COIL TUBING ASSY (M1, M2)0202G0028361EVAP COIL TUBING ASSY (M3, M4)0202G0028861EVAP COIL TUBING ASSY (M5, M6, M7)0202G0029061EVAP COIL TUBING ASSY (M15, M16, M17, M18, M19)0202G0029261EVAP COIL TUBING ASSY (M8)0202G0032061TUBING ASSY, EVAP COIL (M9, M10)0202G0031661COND COIL TUBING ASSY (M8, M9, M10)0201G0013991COND COIL TUBING ASSY (M1, M2, M3, M4, M5, M6, M7)0201G0014291COND COIL TUBING ASSY (M15, M16, M17, M18, M19)0201G0014391COND COIL TUBING ASSY (M11, M12, M13, M14)0201G0014491DRAIN TUBE 32" (M1, M2, M3, M4, M5, M6, M7)20498302161DRAIN TUBE 40" (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20498301161CAP WITH O-RING (QTY 2)0163M00175171EVAP DRAIN FITTING 20513001271DRIP PAN, EVAP COIL20464901DF 421COMPRESSOR GROMMET (M1, M2, M3, M4)B1339530NS COMPRESSOR GROMMET (M5, M6, M7, M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)B1339533NSCOMPRESSOR SCROLL HARNESS (M5, M6, M7)0159G00002NS COMPRESSOR SCROLL HARNESS (M9, M10, M11, M12, M14, M15, M17, M18)0159G00006NS COMPRESSOR SCROLL HARNESS (M8, M13, M16, M19)0159G00007NS CUT-OUT SWITCH, HIGH PRESSURE 0130M00018NS EVAP DRIP SHIELD 0121G00324NS HOSE CLAMP 1.25 (QTY 2)B1810011NS SINGLE-FLOW FILTER DRIER, STEEL (M1, M2, M3, M4, M5, M6, M7)B1219212NS SINGLE-FLOW FILTER DRIER, STEEL (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)B1219225NSTF SHOULDER SCREW (QTY 4)M0221641NS Image 2:FLOWRATOR .053 (M1, M2)0162M0011682FLOWRATOR .062 (M3, M4)B131486282FLOWRATOR .070 (M5, M6, M7)0162M0011782FLOWRATOR .072 (M9, M10)0162M0011882FLOWRATOR .076 (M11, M12, M13, M14)B131487682FLOWRATOR .087 (M15, M16, M17, M18, M19)0162M0011982FLOWRATOR W/COPPER STUB (M8)B131486882Expanded Model Nomenclature M1 - GPG1324045M41AA M2 - GPG1324070M41AA M3 - GPG1330045M41AA M4 - GPG1330070M41AA M5 - GPG1336045M41AA M6 - GPG1336070M41AA M7 - GPG1336090M41AA M8 - GPG1336090M43AA M9 - GPG1342070M41AA M10 - GPG1342090M41AA M11 - GPG1348070M41AA M12 - GPG1348090M41AA M13 - GPG1348090M43AA M14 - GPG1348115M41AA M15 - GPG1360090M41AA M16 - GPG1360090M43AA M17 - GPG1360115M41AA M18 - GPG1360140M41AA M19 - GPG1360140M43AAHeat Exchanger/Manifold/Gas ValveHeat Exchanger/Manifold/Gas ValveRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:ID BLOWER0131G00000P 21ID BLOWER PLATE LRG 3 BRNR (M9, M11)2046320431ID BLOWER PLATE LRG 4 BRNR (M8, M10, M12, M13, M15, M16)2046320131ID BLOWER PLATE LRG 5 BRNR (M14, M17)2046320231ID BLOWER PLATE LRG 6 BRNR (M18, M19)2046320331ID BLOWER PLATE SML 2 BRNR (M1, M3, M5)2046310131ID BLOWER PLATE SML 3 BRNR (M2, M4, M6)2046310231ID BLOWER PLATE SML 4 BRNR (M7)2046310331PRESSURE SWITCH1111250141HEAT EXCHANGER ASSY (M2, M4, M6)430502051HEAT EXCHANGER ASSY (M1, M3, M5)430502151HEAT EXCHANGER ASSY (M9, M11)430502451HEAT EXCHANGER ASSY 4B (LRG-12) (M8, M10, M12, M13, M15, M16)430501151HEAT EXCHANGER ASSY 4B (MED-12) (M7)430500851HEAT EXCHANGER ASSY 5B (LRG-12) (M14, M17)430501251HEAT EXCHANGER ASSY 6B LRG (M18, M19)430500651IGNITOR0130F0001471GAS VALVE (36G) (M1, M2, M3, M4, M5, M6, M7, M8, M9, M10, M11, M12, M13, M14, M15, M16, M17)B128262881FLAME SENSOR0130F0001091MANIFOLD - 2 BRNR (M1, M3, M5)0121M00035P 101MANIFOLD - 3 BRNR (M9, M11)0121M00036P 101MANIFOLD - 3 BRNR (M2, M4, M6)20493103101MANIFOLD - 4 BRNR (M7)20493104101MANIFOLD - 4 BRNR (M8, M10, M12, M13, M15, M16)20493105101MANIFOLD - 5 BRNR (M14, M17)20493106101MANIFOLD - 6 BRNR (M18, M19)20493107101BECKETT BURNER (QTY A/R)10735102111BURNER BRACKET 2B (M1, M3, M5)20190410121BURNER BRACKET 3B (M2, M4, M6, M9, M11)20190411121BURNER BRACKET 4B (M7, M8, M10, M12, M13, M15, M16)20190412121BURNER BRACKET 5B (M14, M17)20190413121BURNER BRACKET 6B (M18, M19)0121F00145121MANUAL RESET LIMIT-GREEN 10123529131FLUE ELBOW LEFT 20484401141FLUE ELBOW RIGHT20484402141ORIFICE SHIELD (M1, M3, M5)11072201151ORIFICE SHIELD (M2, M4, M6)11072202151ORIFICE SHIELD (M7, M8, M10, M12, M13, M15, M16)11072203151ORIFICE SHIELD (M14, M17)11072204151ORIFICE SHIELD (M18, M19)11072205151HEAT DEFLECTOR11190202161ID BLOWER PLATE GASKET LRG (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)20463001NS ID BLOWER PLATE GASKET SML (M1, M2, M3, M4, M5, M6, M7)20462801NS ORIFICE (QTY A/R)10716003NSExpanded Model Nomenclature M1 - GPG1324045M41AA M2 - GPG1324070M41AA M3 - GPG1330045M41AA M4 - GPG1330070M41AA M5 - GPG1336045M41AA M6 - GPG1336070M41AA M7 - GPG1336090M41AA M8 - GPG1336090M43AA M9 - GPG1342070M41AA M10 - GPG1342090M41AA M11 - GPG1348070M41AA M12 - GPG1348090M41AA M13 - GPG1348090M43AA M14 - GPG1348115M41AA M15 - GPG1360090M41AA M16 - GPG1360090M43AA M17 - GPG1360115M41AA M18 - GPG1360140M41AA M19 - GPG1360140M43AAControl PanelControl PanelRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:TRANSFORMER 208/230, 24V0130M0013811CONTACTOR 25 AMP, 1P, 24V (M1, M2, M3, M4, M5, M6, M7)CONT1P025024V 21CONTACTOR 25 AMP, 3P, 24V (M8, M13, M16, M19)CONT3P025024V 21CONTACTOR 30 AMP, 1P, 24V (M9, M10, M11, M12, M14, M15, M17, M18)CONT1P030024V 21IGNITION BOARD, DSI INTEGRATED (M1, M2, M3, M4, M5, M6, M7, M9, M10, M11, M12, M14, M15, M17, M18)PCBAG12341CAPACITOR 5/35/440V (M1, M2, M3, M4)CAP050350440CS 51CAPACITOR 5/370V (M8, M13, M16, M19)CAP050000370LA 51CAPACITOR 5/45/440V/DUAL RD (M5, M6, M7, M9, M10, M11, M12, M14)CAP050450440CT 51CAPACITOR 5/70/440V/DUAL RD (M15, M17, M18)CAP050700440CT 51CAPACITOR STRAP2052090161LIMIT SWITCH (M1, M2, M3, M4)1072834271LIMIT SWITCH (M5, M6, M7, M18, M19)1072834371LIMIT SWITCH (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17)107283447124V RELAY (M11, M12, M13, M14, M15, M16, M17, M18, M19)B1370751101ASSY, FEMALE PLUG0259G00091NS BLOWER HARNESS (M1, M2, M3, M4, M5, M6, M7, M8, M9, M10)0259G00009NS BLOWER, HARNESS (M13, M16, M19)0259G00011NS BLOWER, HARNESS (M11, M12, M14, M15, M17, M18)0259G00023NS HARNESS-CONTROL (M1, M2)0259G00080NS HARNESS-CONTROL (M9, M10)0259G00081NS HARNESS-CONTROL (M11, M12, M14)0259G00083NS HARNESS-CONTROL (M13, M15, M16, M17, M18, M19)0259G00084NS HARNESS-CONTROL (M3, M4)0259G00085NS HARNESS-CONTROL (M5, M6, M7, M8)0259G00086NS PLUG ASSY, 12 PIN MALE (M8, M9, M10, M11, M12, M13, M14, M15, M16, M17, M18, M19)0259G00090NS PLUG ASSY, 12 PIN MALE (M1, M2, M3, M4, M5, M6, M7)0259G00093NSExpanded Model Nomenclature M1 - GPG1324045M41AA M2 - GPG1324070M41AA M3 - GPG1330045M41AA M4 - GPG1330070M41AA M5 - GPG1336045M41AA M6 - GPG1336070M41AA M7 - GPG1336090M41AA M8 - GPG1336090M43AA M9 - GPG1342070M41AA M10 - GPG1342090M41AA M11 - GPG1348070M41AA M12 - GPG1348090M41AA M13 - GPG1348090M43AA M14 - GPG1348115M41AA M15 - GPG1360090M41AA M16 - GPG1360090M43AA M17 - GPG1360115M41AA M18 - GPG1360140M41AA M19 - GPG1360140M43AA。

播种机 D9 2500 3000 Special D9 3000 3500 4000 Super 操

操作说明书az播种机D9 2500/3000 SpecialD9 3000/3500/4000 SuperMG5346BAH0041-6 09.21首次调试前阅读并遵守本操作说明书！妥善保存以备将来使用！zh识别数据在此输入机器的识别数据。

识别数据见铭牌。

型号： D9机器识别号（10位）：生产年份：允许的总重量[kg]：生产商地址AMAZONEN-WERKEH. DREYER SE & Co. KG邮政信箱 51D-49202电话：电子信箱：Hasbergen+ 49 (0) 5405 50 1-0******************备件订购备件清单请访问备件门户网站 www.amazone.de。

复制以及摘要需经 AMAZONEN-WERKE H. DREYER SE & Co. KG公司批准。

D9 BAH0041-6 09.213前言尊敬的客户，您选择了一款来自 AMAZONEN-WERKE，H. DREYER SE & Co. KG 公司丰富产品线的优质产品。

我们非常感谢您的信任。

收到机器时请确认，是否有运输损坏或是否丢失零件。

根据交货单，检查交付机器的完整性，包括订购的选配装备。

只有立即投诉才能获得赔偿。

首次调试前阅读并遵守本操作说明书，尤其是安全注意事项。

仔细阅读后可以充分发挥新购机器的优势。

确保机器的所有操作员在运行机器前都已阅读过本操作说明书。

如有疑问或问题，请仔细阅读本操作说明书或联系您当地的服务商。

定期维护和及时更换磨损或损坏的零件会提高机器的使用寿命。

4 D9 BAH0041-6 09.211 用户注意事项 (12)2 一般安全注意事项 (13)2.1 义务与责任 (13)2.2 安全标识说明 (15)2.3 组织措施 (16)2.4 安全和防护装置 (16)2.5 非正式安全措施 (16)2.6 人员培训 (17)2.7 正常运行中的安全措施 (18)2.8 残留能量危害 (18)2.9 维护与修理，故障排除 (18)2.10 结构性更改 (18)2.10.1 备件和磨损件及助剂 (19)2.11 清洁和废弃处置 (19)2.12 操作员的工作岗位 (19)2.13 机器的警示图 (20)2.13.1 警示图的位置 (26)2.14 不遵守安全注意事项的危险 (28)2.15 工作安全意识 (28)2.16 操作员的安全注意事项 (29)2.16.1 一般安全和事故预防提示 (29)2.16.2 液压系统 (33)2.16.3 电气系统 (34)2.16.4 悬挂设备 (35)2.16.5 播种机的操作 (36)2.16.6 清洁、维护和修理 (36)3 交付时机器的装载和卸载 (37)4 产品说明 (38)4.1 播种机D9组件 (38)4.2 安全和防护装置 (44)4.3 概览 – 供电电缆 / 液压软管 (45)4.3.1 供电电缆 (45)4.3.2 液压软管标识 (45)4.3.2.1 拖拉机控制器的控制方式 (45)4.3.3 拖拉机控制器的连接和功能 (46)4.4 交通装备 (47)4.5 合规使用 (48)D9 BAH0041-6 09.2154.6 危险区域和危险位置 (49)4.7 铭牌和 CE 标志 (50)4.8 D9 Special技术数据 (51)4.9 D9 Super技术数据 (52)4.9.1 计算拖拉机重量和拖拉机轴荷的技术数据 (53)4.9.2 轮胎配置和充气压力 (54)4.10 轮胎拧紧扭矩 (54)4.11 所需的拖拉机配置 (55)5 结构和功能 (56)5.1 组合可能性 (57)5.2 AMAZONE AMACO公顷计数器 (58)5.3 AMAZONE操作终端AmaLog+ (58)5.4 AMAZONE操作终端AmaDrill+ (59)5.5 操作终端 AMATRON 3 (59)5.6 机器文档 (60)5.7 种箱和加料板 (60)5.8 加料量指示器 (60)5.9 加料量监控装置 (61)5.10 油菜播种插件 (62)5.11 种箱分隔板 (62)5.12 播种轴驱动器 (63)5.12.1 播种量，以液压方式设置 (64)5.12.2 播种量, 电子调节 (64)5.13 定量给料装置 (65)5.13.1 设定值 (66)5.13.2 普通和精细播种轮 (68)5.13.3 精细播种轮刷 (68)5.13.4 豆类种子播种轮 (68)5.13.5 滑门 (69)5.13.6 底部出料口 (69)5.13.7 搅拌轴辅助功能 (70)5.14 设置播种量 (71)5.14.1 在带有电子播种量设置系统的播种机上通过滑动在车轮上重新计算曲柄转数 (74)5.15 WS犁刀 (76)5.15.1 带状播种鞋 (76)5.16 控制犁刀RoTeC (77)5.17 犁刀压力和播种深度（所有犁刀类型） (79)6 D9 BAH0041-6 09.215.17.1 犁刀压力设置，外侧 (79)5.17.2 犁刀压力设置，集中 (79)5.17.3 犁刀压力设置，液压 (80)5.18 精耕耙 (81)5.18.1 精耕耙齿位置 (81)5.18.2 精耕耙压力 (82)5.18.2.1 精耕耙压力调节系统，机械式 (82)5.18.2.2 精耕耙压力调节系统，液压式 (82)5.19 轧滚耙 (83)5.20 拖动式齿耙 (84)5.21 播种机车轮-轮迹松土器 (84)5.22 拖拉机车轮轮迹松土器 (85)5.23 划行器 (86)5.24 行驶轨道 (88)5.24.1 行驶轨道切换档位，通过表格确定 (89)5.24.2 行驶轨道切换档位，通过图表确定 (90)5.24.3 功能说明 (92)5.24.3.1 中间轴联轴器，机械驱动 (93)5.24.3.2 中间轴联轴器，液压驱动 (94)5.24.3.3 中间轴联轴器，电动驱动 (94)5.25 半侧切换装置 (95)5.25.1 行驶轨道切换档位2和21 (96)5.25.2 通过4 m播种机作业宽度创建18 m行驶轨道 (97)5.26 行驶轨道划线器 (98)6 调试 (99)6.1 检查拖拉机的适用性 (100)6.1.1 计算拖拉机总重量，拖拉机轴荷和胎承载能力以及所需的最低压载的实际值 (101)6.1.1.1 所需的计算数据（悬挂的机器） (102)6.1.1.2 计算拖拉机前部所需的最小压载 G V min，以保证转向能力 (103)6.1.1.3 计算拖拉机的实际前轴载荷 T V tat (103)6.1.1.4 计算拖拉机和机器组合的实际总重量 (103)6.1.1.5 计算拖拉机的实际后轴载重 T H tat (103)6.1.1.6 拖拉机轮胎承载能力 (103)6.1.1.7 表 (104)6.2 防止拖拉机/机器意外启动和意外滚动 (105)6.3 用于运输保险护板的支架的首次安装 (106)7 挂接和脱开机器 (107)7.1 液压软管 (109)D9 BAH0041-6 09.2177.1.1 连接液压软管 (109)7.1.2 脱开液压软管管路 (110)7.2 连接机器 (111)7.2.1 将机器与拖拉机挂接 (113)7.2.2 连接机器和拖拉机 (115)8 设置 (116)8.1 展开和折叠梯子 (117)8.2 将校准盘置于料斗轨道上 (118)8.3 设置播种量 (120)8.3.1 通过普通和精细播种轮播种 (120)8.3.2 通过豆类种子播种轮播种 (122)8.3.3 设置滑门 (123)8.3.4 底部出料口位置 (124)8.3.5 设置数字加料量传感器 (124)8.3.6 安装油菜播种插件 (125)8.3.7 搅拌轴辅助功能 (126)8.4 为种箱加料 (127)8.5 通过校准测试设置种子量 (130)8.5.1 借助量盘计算变速器档位 (133)8.5.2 液压播种量遥控调节装置 (134)8.6 将划行器置于作业/运输位置 (136)8.6.1 将带有自动控制装置的划行器置于作业位置 (137)8.6.2 将划行器D9 2500/3000/3500置于作业位置 (138)8.6.3 将划行器D9 4000置于作业位置 (138)8.6.3.1 设置划行器的长度 (139)8.6.4 将划行器置于运输位置 (140)8.7 设置和检查播种深度 (141)8.7.1 用于犁刀压力的调节，中央 (141)8.7.2 犁刀压力调节，液压 (142)8.7.3 设置外侧犁刀的播种深度 (143)8.7.4 设置深度控制盘/轮 (144)8.8 固定在WS犁刀上的带状播种鞋 (145)8.9 设置播种机车轮-轮迹松土器 (146)8.9.1 将播种机车轮-轮迹松土器置于作业位置 (146)8.9.2 将播种机车轮-轮迹松土器置于运输位置 (146)8.10 设置拖拉机车轮轮迹松土器 (147)8.10.1 拖拉机车轮轮迹松土器，经强化 (147)8.10.2 拖拉机车轮轮迹松土器，可回转 (148)8.11 设置精耕耙 (149)8 D9 BAH0041-6 09.218.11.1 精密耙的工作宽度 (149)8.11.2 精耕耙齿位置 (149)8.11.2.1 通过换装螺栓设置精耕耙齿位置 (149)8.11.2.2 通过调节主轴设置精耕耙齿位置 (150)8.11.3 精密耙压力，手动设置 (151)8.11.4 设置精密耙压力，液压式 (151)8.11.5 将精耕耙置于作业/运输位置 (152)8.11.5.1 将精耕耙置于作业位置 (152)8.11.5.2 将精耕耙置于运输位置 (152)8.12 设置轧滚耙 (153)8.12.1 设置耙齿与土壤之间的角度 (153)8.12.2 设置耙齿的作业深度 (153)8.12.3 设置压辊接触压力 (154)8.12.4 提起/降下轧滚耙 (156)8.12.4.1 提起轧滚耙（禁用） (156)8.12.4.2 降下轧滚耙（激活） (157)8.13 带有机械式或液压式中间轴联轴器驱动装置的播种机 (158)8.13.1 激活行驶轨道切换档位 (158)8.13.2 禁用行驶轨道切换 (159)8.14 带有电动中间轴联轴器驱动装置的播种机 (159)8.14.1 激活行驶轨道切换档位 (159)8.14.2 禁用行驶轨道切换 (159)8.15 断开播种轴的左侧一半 (160)8.15.1 断开播种轴的左侧一半 (160)8.15.2 接通播种轴的左侧一半 (160)8.16 将行驶轨道划线器置于作业/运输位置 (161)8.16.1 将行驶轨道划线器置于作业位置 (161)8.16.2 将行驶轨道划线器置于运输位置 (162)8.17 将运输保险护板置于运输/停车位置 (163)9 运输 (164)9.1 将播种机置于运输位置 (164)9.2 法律规定和安全 (165)10 机器的使用 (169)10.1 首次启动 (170)10.2 机器在运输前转换到作业位置。

ZGM133G使用维护说明书（参考）

ZGM133G使用维护说明书（参考）2006年11月目录前言 (1)第一篇磨煤机使用和操作说明 (2)1.代号和技术数据 (3)2.工作原理 (3)3.部件介绍 (5)4.使用、操作要求 (10)5.启、停说明 (13)6.启动前和运行检查 (17)7.运行故障及处理 (18)第二篇磨煤机维护、检修说明 (21)1.维护、检修注意事项 (22)2.停机时的保养与维护内容 (23)3.维护、检修要求 (26)4.碾磨件及内部零部件拆卸与安装 (29)5.内部部件的维修 (32)第三篇盘车装置使用和维护说明 (37)1.技术要求 (38)2.使用要求 (38)3.安装与调整 (39)4.维护保养 (39)第四篇磨煤机安装与调试导则 (40)1.安装事宜 (41)2.安装说明 (41)3.启动前的调试 (48)附录：附表1: ZGM133G型中速辊式磨煤机大件起吊单重重量表附表2: ZGM133G型中速辊式磨煤机润滑油脂一览表ZGM133G型中速辊式磨煤机使用和维护说明书前言感谢您选用了我厂的ZGM型中速辊式磨煤机，为了使您更好地了解设备，使设备更好地为您的系统服务，我们编写了这本使用说明书，希望能给您以帮助，并真诚地希望您对其中的不足之处给予指出。

本使用说明书是根据ZGM型中速辊式磨煤机的特点和现场运行情况编写的，其中对磨煤机的运行、检查、维护、检修要求大部分是针对磨煤机易出问题的环节和总结现场出现的问题而提出的，所以下面提出的要求，用户在使用过程中请务必遵守：①磨煤机运行应严格按照运行要求，不能违章操作。

②必须保证一次风量，一次风量的测量装置要定期标定，这对磨煤机运行极为重要。

③定期对磨煤机检查、维护，绝不允许连续数千小时不停磨、不检查、不间断地运行。

④一次风入口隔绝门至关重要，没有严密的隔绝门就无法进入磨内检查、维护和检修。

⑤出粉管上要有隔绝门。

⑥必须为检查、维护、检修工作创造必要的条件。

⑦应配置单独的密封风系统，不要直接采用冷一次风作为密封风。

3-3-13型车钩量具样板使用

距钩舌上、下边缘向内13A或B型 60mm处，量规A、B点和C部分别与钩舌正面、钩舌鼻部和钩舌内腕贴靠，移动滑尺与钩舌S面接触，滑尺示值小于69mm 时超限。
钩舌综合测量
量规工作面与钩舌锁面贴靠，沿锁面移动量规，45T端在钩锁承台面通过时合格。检测钩舌锁面上平面与钩锁承台的距离。段修限度：≥45
13A、B型车钩量具样板使用规范
2012年10月制作
13型车钩所需样板量具
现场检测13B型车钩流程：首先进行钩高度测量，然后依次取出开口销、钩圆销、钩舌、锁铁、推铁、上锁销。
测量车钩高度： 880±10mm注意三要素：平行、贴靠、垂直
钩舌综合测量
A点 B点 C点 A点 B点 C点
钩舌外胀检测：将量具A、B两点分别与钩舌尾端，钩舌正面弯曲部贴靠，如C点部位与钩舌鼻部外侧接触则外胀超限。段修 ≤6mm。
检测钩腔上防跳台磨耗最深处与上锁销孔上平面的距离：量规 53Z端从上锁销孔内插入上平面与上防跳台之间，在磨耗最深处止不住时超限。
13型车钩钩耳孔、衬套孔磨耗检测
钩耳孔磨耗：距钩耳孔边缘10mm处分别检测钩耳孔或衬套的长径、短径。量规 47Z、45Z 端分别插入钩耳孔长径和短径，深入超过 10mm时超限。
用样板29Z端插入钩舌推铁轴磨耗严重处，插入量超半径时超限。检测钩舌推铁轴磨耗处最小剩余直径。段修≤2
钩锁铁测量方法
与锁铁贴靠主尺贴靠锁铁，示值剩余厚度。
ห้องสมุดไป่ตู้
滑动滑尺对准磨耗最大处
将量规插入锁铁立面，一面与锁铁接触，滑尺对准磨耗最大处，使主尺与与锁铁贴靠，示值为锁铁厚度剩余值。
13型车钩钩体测量

ZLY型带式输送机自动液压拉紧装置使用说明书

目录一、概述 (1)二、工作原理 (1)三、主要技术参数 (3)四、设备安装及连接 (3)五、现场调试步骤 (4)六、操作规程 (6)七、维护和维修 (7)八、注意事项 (8)九、附录附录一液压拉紧装置推荐用液压油附录二电气外围信号接线图附录三电控系统原理图附录四电控系统面板布置图此为四川向家坝电厂液压自控拉紧装置说明书部分电源线号注有所不同请对照电器图工作原理一致第1 页一、概述带式输送机液压自动拉紧装置是根据我国散料运输特点，吸取世界工业发达国家的先进技术，考虑输送带在起动和正常运行时所需拉紧力不同，确定合理的张力模型而设计的。

本拉紧装置的特点是：（1）改善带式输送机运行时胶带的动态受力效果，特别是胶带受到突变载荷时尤其明显；（2）起动和正常运行的不同拉紧力，可以根据带式输送机的实际需要任意调节（其调节范围由所选拉紧装置的型号规格确定）。

系统一旦调定后，即按预定的程序自动工作，使输送机处在理想的工作状态下运行，大大改善输送带的受力状况。

（3）响应快。

由于输送机起动时，输送带松边会突然松弛伸长，引起“打带”、冲击现象。

此时，拉紧装置能迅速收缩油缸，及时吸收输送带的伸长，从而大大缓和了输送带的冲击，使起动过程平稳，避免发生断带事故。

（4）具有断带时自动停止输送机的保护功能。

（5）结构紧凑，安装空间小，便于使用。

ZLY型液压自动拉紧装置适用于长距离带式输送机的张紧，主要由拉紧油缸、液压泵站、蓄能站、地面PLC型控制开关和拉紧附件等五大部分组成。

其中液压泵站、蓄能站和地面PLC型控制开关不需要做地基，仅要求安放地点不落物料和水即可。

二、工作原理图1为ZLY的液压系统原理图及油缸与拉紧小车缠绕示意图。

为满足带式输送机对拉紧力起动时大，正常运行时小的要求，液压系统可相应地提供高（由溢流阀3控制）和比例阀13两种油压。

为此，首先需将各溢流阀和压力继电器的整定值从大到小依次为溢流阀9、溢流阀3、电接点压力表上、下限、压力继电器。

FZG系列真空干燥机使用说明书

一、概述真空干燥，就是将被干燥物料处于真空条件下，进行加热干燥。

它是利用真空泵进行抽气抽湿，使工作室内形成真空状态，从而加快了干燥速度。

真空干燥理论表明：1、当加热温度恒定，提高真空度，能加快干燥速度。

2、当真空度恒定，提高加热温度，能加快干燥速度。

3、既提高真空度，又提高加热温度，则大大加快干燥速度。

如果采用冷凝器，物料中的蒸发溶剂可通过冷凝器加以回收，是一种常用的干燥设备。

真空干燥的特点：１、在真空下物料溶液的沸点降低，使蒸发器的传热推动力增大，因此有一定的传热量，可以节省蒸发器的传热面积。

２、蒸发操作的热源可以采用低压蒸汽或废热蒸汽（用户特殊要求选用水或导热油加热，厂方可为您专门设计）。

３、蒸发器的热损失可减少；４、适用于在高温下易分解，聚合和变质的热敏性物料的干燥；５、在干燥前可进行消毒处理，干燥过程中任何不纯物均无混入；６、属于静态式真空干燥器，故干燥物料的形体不会损坏。

二、用途适用于医药品、化工、食品、电子、中药等行业的物料干燥。

三、技术参数四、工作原理与主要配套设备FZG系列方形真空干燥器设计有穿流式烘车架，烘车架可拆出。

根据热空气上升的原理，充分利用各层架烘管传导来的热量来达到加快干燥物料的目的。

特别是采用了双蒸汽管间隔分层进汽以及下面两层架烘管的加密，改善了以往静态式真空干燥器温度不均匀的弊端。

真空干燥器密封门铰链装有轴承，设计成浮动结构形式，密封门开启十分轻便，并可在整个密封表面上作微量自由摆动，以贴切密封面提高干燥器内真空度，这样物料均能在较低的温度环境下迅速气化加快干燥。

五、安装１、搬运和吊装干燥器时，应旋紧密封门手轮整体起吊，起吊时应用钢丝绳从器身底部穿入，并使钢丝绳均匀受力，以免使器身发生倾倒。

２、干燥器可安装在厚度为400mm的混凝土基础上，用4只M24x300地脚螺栓紧固,也可直接安放在平整的混凝土地坪上,不必用地脚螺栓紧固,但必须保持干燥器水平安放，便于密封门启闭自如。

重力选机说明书

使用说明书重力式清选机铄金机械设备目录一、图片 (1)二、机器用途及选用围 (2)三、主要规格及工作原理 (2)四、主要结构及工作有理 (2)五、安装要求 (6)六、使用与调整 (6)七、维护与保养……………………………………………11八、常见故障排除…………………………………………11九、安全技术要求…………………………………………13十、三包期的规定…………………………………………13十一、售后服务承诺………………………………………14十二、发货及装箱单………………………………………14十三、本机标准件附表……………………………………15十四、其它…………………………………………………15十五、附图：外形尺寸及安装位置图……………………15一、图片：二、机器用途及适用围1、适用围：5XZ-5.OF重力分选面适用于小麦、水稻、大麦、高粮、玉米、大豆、红小豆、绿豆、白瓜籽等种子及粮食的筛选，通过此机精选后的种子其千粒重、净度、发芽率、发芽势等方面都有显著的提高。

此机呆用于中小型种子加工厂及各类种子、对外出口粮食加工单位使用。

本机不适用于清理尘土、污物、茎杆和其它废物，它不是尺寸分级机，种子在重力分选前如经过彻底地初清和分级会获得最佳效果。

2、代号含义三、主要规格及技术参数四、主要结构及工作原理本机主要由底座、风机、筛床、传动系统、纵横角度调节机构、纵横夹紧机构、喂入斗、分流斗、空气过滤罩、电控装置等部分组成。

（见图一）1、纵向夹紧拉杆2、筛床3、喂入斗4、横向夹紧拉杆5、偏心连杆机构6、筛架7、底座8、空气过滤罩（图一）整机结构图工作时谷物从筛床上方的喂入斗流向筛床，在筛床的振动和气流的作用下，按照不同的等级由卸料口排出，既完成分级过程。

筛床是重力分选中重要的的部分，因为谷物都是通过筛床来进行分选的。

筛床结构图见（图二）筛床为木制结构的，筛床下表面是通风孔板，上表面是金属网，谷物就在其上表面滚动。

玉米烘干机说明书doc

玉米烘干机说明书篇一：烘干机说明书回转式烘干机使用说明Rotary drying machine descriptionHenan Tongda Heavy Industry Technology Co LtdZhengzhou.China河南通达重工科技有限公司中国.郑州目录一：用途二：主要技术参数表三：结构简述及装配四：安装，调试和试车五：使用和维护六：特别声明一、用途回转式烘干机，适用于有机肥料，矿渣,粘土,石灰石,磷石膏,钢厂水渣,电厂煤泥以及污水处理厂污泥等物料的烘干，具有烘干能力大,运转平稳,能耗低,操作方便,产量高等优点。

其通过喷射引风器把热风炉的热风引进烘干机内部与湿物料进行热交换。

根据物料的特性不同,设置不同型式的扬料板以及防粘措施,物料进入旋转筒体内在烘干的同时,筒体内设多角度升举式抄板，使物料扬布均匀从而充分与高温炉气进行热交换，干燥效果好。

二、主要技术参数表产品规格 0.8×8 1.0×10 1.2×12 1.5×15 1.6×16 1.8×18 2.0×20 2.2×22 2.4×24电机功率5.5kw 7.5kw 7.5kw 11kw 15kw 22kw 37kw 37kw 45kw减速机型号 JZQ250 JZQ350 JZQ350 JZQ400 JZQ400 JZQ500 JZQ500 JZQ500 JZQ650进气温度≥300 ≥300 ≥300 ≥300 ≥300 ≥300 ≥300 ≥300 ≥300安装倾斜角 3-5% 3-5% 3-5% 3-5% 3-5% 3-5% 3-5% 3-5% 3-5%转速 6 6 6 6 6 5.8 5.5 5.5 5.2产能 T/h 1-2 2-4 3-5 4-6 6-8 7-12 8-15 8-16 14-18 注:生产能力将随产品的不同组成要求和含水量的不同而变化。