LTE事件列表详情解说

合集下载

LTE常见事件解释及定时器

LTE常见事件解释及定时器

1.1 4.5.1 切换正常流程同频切换同时支持同eNodeB切换,同MME的异eNodeB切换,跨MME的异eNodeB切换场景。

对于后两种场景依据eNodeB间是否建立X2接口,切换信令流程略有不同。

图4-2 同MME异eNodeB间切换流程同MME异eNodeB间的同频切换信令流程如图4-2所示:1.在无线承载建立时,源eNodeB下发RRC Connection Reconfiguration至UE,其中包含source eNodeB 配置的Measurement Configuration消息,用于控制UE连接态的测量过程。

2.UE根据测量结果上报Measurement Report。

3.源eNodeB根据测量报告进行切换决策。

4.当源eNodeB决定切换后,源eNodeB发出HandoverRequest消息给目标eNodeB,通知目标eNodeB准备切换。

5.目标eNodeB进行准入判断,若判断为资源准入,再由目标eNodeB依据EPS的QoS信息执行准入控制。

6.目标eNodeB在L1/L2准备切换并对源eNodeB发送HANDOVER REQUESTACKNOWLEDGE消息。

1.2 报告配置(A1至A5 B1至B2)事件触发上报是3GPP 36.331协议中为切换测量与判决定义的一个概念。

报告配置包含相应事件的相关参数。

目前eNodeB应用以下事件触发相应动作:●事件A1表示服务小区质量高于一定门限,当满足事件触发条件时UE便上报测量报告,eNodeB停止异频/异系统测量。

但在基于频率优先级的切换中,事件A1用于启动异频测量。

●事件A2表示服务小区质量低于一定门限,当满足事件触发条件时UE便上报测量报告,eNodeB启动异频/异系统测量。

但在基于频率优先级的切换中,事件A2用于停止异频测量。

●事件A3表示同频/异频邻区质量相比服务小区质量高出一定门限,当满足事件触发条件的小区信息被上报时,源eNodeB启动同频/异频切换请求。

LTE系统事件简介

LTE系统事件简介

LTE系统事件简介一、LTE事件概述LTE切换时需要UE上报测量的结果(包括RSRP,RSRQ等),而上报又分为周期性上报和事件触发的上报。

➢周期性上报由基站配置,UE直接上报测量的结果。

➢事件触发的上报又分为系统内的事件和系统间的事件。

LTE系统内切换主要事件包括:➢A1事件,服务小区质量高于门限;这个事件可以用来关闭频间测量。

➢A2事件,服务小区质量低于门限;这个事件可以用来打开频间测量和系统间测量,因为这个事件发生后可能发生切换等操作。

➢A3事件,邻小区质量好于服务小区质量;这个事件一般用于频内/间基于覆盖的切换。

➢A4事件,邻小区质量好于门限;这个事件一般用于基于负荷的切换。

➢A5事件,服务小区质量低于一个门限并且邻小区质量高于一个门限;这个事件也可以用于频内/间基于覆盖的切换。

目前LTE同频切换都是基于A3/A5事件进行的切换(现网主要是基于A3事件的)二、切换流程举例三、切换流程简要说明- RRC Connection Reconfiguration(Measurement Control)测量控制,一般在初始接入或上一次切换命令中的重配消息里携带- Measurement Report测量报告,终端根据当前小区的测量控制信息,将符合切换门限的小区进行上报- HO Request源小区在收到测量报告后向目标小区申请资源及配置信息(站内切换的话为站内交互,站间切换会使用X2口或者S1口,优先使用X2口)- HO Request Ack目标小区将终端的接纳信息以及其它配置信息反馈给源小区- RRC Connection Reconfiguration(HO Command)将目标小区的接纳信息及配置信息发给终端,告知终端目标小区已准备好终端接入,重配消息里包含目标小区的测量控制- SN Status Transfer源小区将终端业务的缓存数据移至目标小区- Random Access Preamble终端收到第5步重配消息(切换命令)后使用重配消息里的接入信息进行接入- Random Access Response目标小区接入响应,收到此命令后可认为接入完成了,然后终端在RRC层上发重配完成消息(第9步)- RRC Connect Reconfiguration complete(HO Confirm)上报重配完成消息,切换完成- Release Resource当终端成功接入后,目标小区通知源小区删除终端的上下文信息四、协议对LTE事件的定义和说明4.1 A1事件定义Event A1 (Serving becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A1-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A1-1 (Entering condition)-Ms>HysThreshInequality A1-2 (Leaving condition)Ms<+ThreshHysThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a1-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.2 A2事件定义Event A2 (Serving becomes worse than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A2-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A2-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A2-1 (Entering condition)+Ms<HysThreshInequality A2-2 (Leaving condition)Ms>-HysThreshThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a2-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.3 A3事件定义Event A3 (Neighbour becomes offset better than PCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A3-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A3-2, as specifiedbelow, is fulfilled;NOTE The cell(s) that triggers the event is on the frequency indicated in the associated measObject which may be different from the (primary) frequency used by the PCell.Inequality A3-1 (Entering condition)++>+Mn++-OcnOfpOcpMpHysOffOfnInequality A3-2 (Leaving condition)++<Mn++++MpOcpOfnOfpOffHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Mp is the measurement result of the PCell, not taking into account any offsets.Ofp is the frequency specific offset of the primary frequency (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the primary frequency).Ocp is the cell specific offset of the PCell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the primary frequency), and is set to zero if not configured for the PCell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a3-Offset as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Ofp, Ocp, Hys, Off are expressed in dB.4.4 A4事件定义Event A4 (Neighbour becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A4-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A4-2, as specifiedbelow, is fulfilled;Inequality A4-1 (Entering condition)-+Mn>+HysThreshOcnOfnInequality A4-2 (Leaving condition)Mn<+++ThreshOfnHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a4-Threshold as defined within reportConfigEUTRA for this event).Mn is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.5 A5事件定义Event A5 (PCell becomes worse than threshold1 and neighbour becomes better than threshold2)The UE shall:1> consider the entering condition for this event to be satisfied when both condition A5-1 andcondition A5-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition A5-3 or condition A5-4, i.e. at least one of the two, as specified below, is fulfilled;NOTE: The cell(s) that triggers the event is on the frequency indicated in the associatedmeasObject which may be different from the (primary) frequency used by the PCell.Inequality A5-1 (Entering condition 1)1Thresh Hys Mp <+Inequality A5-2 (Entering condition 2)2Thresh Hys Ocn Ofn Mn >-++Inequality A5-3 (Leaving condition 1)1Thresh Hys Mp >-Inequality A5-4 (Leaving condition 2)2Thresh Hys Ocn Ofn Mn <+++The variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh1 is the threshold parameter for this event (i.e. a5-Threshold1 as defined within reportConfigEUTRA for this event).Thresh2 is the threshold parameter for this event (i.e. a5-Threshold2 as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh1 is expressed in the same unit as Mp .Thresh2 is expressed in the same unit as Mn .Event A6 (Neighbour becomes offset better than SCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A6-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A6-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the (secondary) cell that is configured on the frequency indicatedin the associated measObjectEUTRA to be the serving cell;NOTE: The neighbour(s) is on the same frequency as the SCell i.e. both are on the frequency indicated in the associated measObject.Inequality A6-1 (Entering condition)+>Mn++-MsOcsOffHysOcnInequality A6-2 (Leaving condition)+<+Mn++OcsOffMsHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Ms is the measurement result of the serving cell, not taking into account any offsets.Ocs is the cell specific offset of the serving cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the serving frequency), and is set to zero if not configured for the serving cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a6-Offset as defined within reportConfigEUTRA for this event).Mn, Ms are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ocn, Ocs, Hys, Off are expressed in dB.Event B1 (Inter RAT neighbour becomes better than threshold)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when condition B1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition B1-2, as specifiedbelow, is fulfilled;Inequality B1-1 (Entering condition)Thresh+Mn>-HysOfnInequality B1-2 (Leaving condition)++Mn<ThreshHysOfnThe variables in the formula are defined as follows:Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA 2000 measurement result, pilotStrength is divided by -2.Ofn is the frequency specific offset of the frequency of the inter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the neighbour inter-RAT cell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh is the threshold parameter for this event (i.e. b1-Threshold as defined within reportConfigInterRAT for this event). For CDMA2000, b1-Threshold is divided by -2.Mn is expressed in dBm or in dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.8 B2事件定义Event B2 (PCell becomes worse than threshold1 and inter RAT neighbour becomes better than threshold2)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when both condition B2-1 andcondition B2-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition B2-3 or conditionB2-4, i.e. at least one of the two, as specified below, is fulfilled;Inequality B2-1 (Entering condition 1)+HysMp<Thresh1Inequality B2-2 (Entering condition 2)-+Mn>Ofn2ThreshHysInequality B2-3 (Leaving condition 1)Hys-Mp>1ThreshInequality B2-4 (Leaving condition 2)Mn<++OfnHys2ThreshThe variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA2000 measurement result, pilotStrength is divided by -2.Ofn is the frequency specific offset of the frequency of the inter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the inter-RAT neighbourcell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh1 is the threshold parameter for this event (i.e. b2-Threshold1 as defined within reportConfigInterRAT for this event).Thresh2 is the threshold parameter for this event (i.e. b2-Threshold2 as defined within reportConfigInterRAT for this event). For CDMA2000, b2-Threshold2 is divided by -2.Mp is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Mn is expressed in dBm or dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.修正版Thresh1 is expressed in the same unit as Mp. Thresh2 is expressed in the same unit as Mn.。

LTE事件解释18页

LTE事件解释18页

1 4.5.1 切换正常流程同频切换同时支持同eNodeB切换,同MME的异eNodeB切换,跨MME的异eNodeB切换场景。

对于后两种场景依据eNodeB间是否建立X2接口,切换信令流程略有不同。

图4-2 同MME异eNodeB间切换流程同MME异eNodeB间的同频切换信令流程如图4-2所示:1. 在无线承载建立时,源eNodeB下发RRC ConnectionReconfiguration至UE,其中包含source eNodeB 配置的Measurement Configuration消息,用于控制UE连接态的测量过程。

2. UE根据测量结果上报Measurement Report。

3. 源eNodeB根据测量报告进行切换决策。

4. 当源eNodeB决定切换后,源eNodeB发出HandoverRequest消息给目标eNodeB,通知目标eNodeB准备切换。

5. 目标eNodeB进行准入判断,若判断为资源准入,再由目标eNodeB依据EPS的QoS信息执行准入控制。

6. 目标eNodeB在L1/L2准备切换并对源eNodeB发送HANDOVERREQUEST ACKNOWLEDGE消息。

3.1.2 报告配置事件触发上报是3GPP 36.331协议中为切换测量与判决定义的一个概念。

报告配置包含相应事件的相关参数。

目前eNodeB应用以下事件触发相应动作:事件A1表示服务小区质量高于一定门限,当满足事件触发条件时UE便上报测量报告,eNodeB停止异频/异系统测量。

但在基于频率优先级的切换中,事件A1用于启动异频测量。

事件A2表示服务小区质量低于一定门限,当满足事件触发条件时UE便上报测量报告,eNodeB启动异频/异系统测量。

但在基于频率优先级的切换中,事件A2用于停止异频测量。

事件A3表示同频/异频邻区质量相比服务小区质量高出一定门限,当满足事件触发条件的小区信息被上报时,源eNodeB启动同频/异频切换请求。

LTE事件

LTE事件
Event A2(Serving becomes worse than threshold):表示服务小区信号质量低于一定门限,满足此条件的事件被上报时,eNodeB启动异频/异系统测量;类似于UMTS的2D事件。
Event A3(Neighbour becomes offset better than serving):表示邻区质量高于服务小区一定门限并且保持一定时间,满足此条件的事件被上报时,源eNodeB启动切换请求;类似于UMTS的1G/2A事件。
Event A4(Neighbour becomes better限量,满足此条件的事件被上报时,源eNodeB启动切换请求;类似于GSM里面的HCS切换。
Event A5(Serving becomes worse than threshold1 and neighbour becomes better than threshold2):表示服务小区质量低于一定门限且邻区质量高于一定门限;类似于UMTS的2B事件。
切换算法:
——事件(一般同频用A3,异频用A1/A2+A5,异系统用A1/A2+B2)
Event A1(Serving becomes better than threshold):表示服务小区信号质量高于一定门限,满足此条件的事件被上报时,eNodeB停止异频/异系统测量;类似于UMTS的2F事件。
Event B1(Inter RAT neighbour becomes better than threshold):表示异系统邻区质量高于一定门限,满足此条件事件被上报时,源eNodeB启动异系统切换请求;类似于UMTS的3C事件。
Event B2(Serving becomes worse than threshold1 and inter RAT neighbour becomes better than threshold2):表示服务小区质量低于一定门限并且异系统邻区质量高于一定门限,类似于UMTS的3A事件。

LTE切换事件介绍

LTE切换事件介绍

Ocn:邻小区个性偏移(CIO)
Hys(5):A5事件迟滞参数 Thersh1:A5事件门限1参数 Thersh2:A5事件门限2参数
B1事件的切换参数配置
B1事件表示:异系统邻区质量高于一个绝对门限,满足事件触发条件的小 区信息被上报时,源eNodeB启动异系统切换请求,用于基于负荷的切换 B1事件判决公式: 触发条件: Mn + Ofn - Hys(b1) > Thersh(b1) 取消条件:Mn + Ofn + Hys(b1) > Thersh(b1) 其中: Mn:邻小区测量结果 Ofn:邻小区频率特定的偏差,默认为0
根据A1事件触发条件:Ms – Hys(1) > Thersh(1)可以算出: Ms>-86时关闭异频测量。 根据A2事件触发条件:Ms + Hys(2) < Thersh(2) 可以算出: Ms<-92时开启异频测量 则当UE测量到的A小区RSRP值为红色区域时,UE不进行异频测量;当 UE测量到的A小区RSRP值为绿色区域时,UE进行异频测量;当UE测量到的A 小区RSRP值为黄色区域时,UE是否进行异频测量取决于UE之前的状态,即 UE的测量状态并不改变。
频内/频间基于覆盖的切换 B1事件:异系统邻区质量高于一个绝对门限,用于基于负荷的切换。
B2事件:服务小区质量低于一个绝对门限1且异系统邻区质量高于一个绝对门限2,
用于基于覆盖的切换。
A1事件的切换参数配置
A1事件触发条件:Ms – Hys(1) > Thersh(1) A1事件取消条件:Ms + Hys(2) < Thersh(2) 其中: Ms:服务小区测量结果 Hys(1):A1事件迟滞参数 Hys(2):A2事件迟滞参数 Thersh(1):A1事件门限参数 Thersh(2):A2事件门限参数

AB事件LTE

AB事件LTE

LTE 支持的切换事件有A 类和B 类,其中A 类本用作系统内测量,B 类被用作系统间测量A1事件:表示服务小区信号质量高于一定门限; A2事件:表示服务小区信号质量低于一定门限;A3事件:表示邻区质量高于服务小区质量,用于同频、异频的基于覆盖的切换; A4事件:表示邻区质量高于一定门限,用于基于负荷的切换,可用于负载均衡;A5事件:表示服务小区质量低于一定门限并且邻区质量高于一定门限,可用于负载均衡; 异系统测量事件: B1事件:邻小区质量高于一定门限,用于测量高优先级的异系统小区;B2事件:服务小区质量低于一定门限,并且邻小区质量高于一定门限,用于相同或较低优先级的异系统小区的测量。

LTE 移动性参数(全局)最小接入电平基本信息参数功能该参数表示UE 在该小区驻留需满足的最小接收电平门限。

该值取值范围是2G/3G 接收电平的实际值,对于LTE/3G ,?实际的RxlevMin?等于SIB3/SIB6的IE value 的两倍,调整步长为2dbm 。

对于2G ,实际的RxlevMin 等于SIB7的?(IE value * 2)? ?115,调整步长为2dBm 当UE 测量到的2G/3G 电平满足S 准则时,UE 才可能驻留在该小区。

参数调整影响调整该参数的门限值,会对小区的选择和驻留有所影响。

QrxLevMin 如果设置过高,则UE 将无法驻留到该小区。

高优先级重选门限基本信息参数功能当高优先级小区的S值在一定时间内高于该阀值(threshXHigh)后,UE可以重选到该小区。

参数调整影响调整该参数的门限值,会对小区的选择和驻留有所影响。

threshXhigh如果设置过高,?会增加UE重选到高优先级小区的难度。

低优先级重选门限基本信息参数功能当低优先级小区的S值在一定时间内高于该阀值(threshXLow)后,同时主服务小区的S值低于threshServingLow,UE可以重选到该低优先级小区。

移动LTE系统事件介绍

移动LTE系统事件介绍

LTE系统事件介绍一、LTE事件概述LTE切换时需要UE上报测量的结果(包括RSRP,RSRQ等),而上报又分为周期性上报和事件触发的上报。

周期性上报由基站配置,UE直接上报测量的结果。

事件触发的上报又分为系统内的事件和系统间的事件。

LTE系统内切换主要事件包括:A1事件,服务小区质量高于门限;这个事件可以用来关闭频间测量。

A2事件,服务小区质量低于门限;这个事件可以用来打开频间测量和系统间测量,因为这个事件发生后可能发生切换等操作。

A3事件,邻小区质量好于服务小区质量;这个事件一般用于频内/间基于覆盖的切换。

A4事件,邻小区质量好于门限;这个事件一般用于基于负荷的切换。

A5事件,服务小区质量低于一个门限并且邻小区质量高于一个门限;这个事件也可以用于频内/间基于覆盖的切换。

目前LTE同频切换都是基于A3/A5事件进行的切换(现网主要是基于A3事件的)二、切换流程举例- RRC Connection Reconfiguration(Measurement Control)测量控制,一般在初始接入或上一次切换命令中的重配消息里携带- Measurement Report测量报告,终端根据当前小区的测量控制信息,将符合切换门限的小区进行上报- HO Request源小区在收到测量报告后向目标小区申请资源及配置信息(站内切换的话为站内交互,站间切换会使用X2口或者S1口,优先使用X2口)- HO Request Ack目标小区将终端的接纳信息以及其它配置信息反馈给源小区- RRC Connection Reconfiguration(HO Command)将目标小区的接纳信息及配置信息发给终端,告知终端目标小区已准备好终端接入,重配消息里包含目标小区的测量控制- SN Status Transfer源小区将终端业务的缓存数据移至目标小区- Random Access Preamble终端收到第5步重配消息(切换命令)后使用重配消息里的接入信息进行接入- Random Access Response目标小区接入响应,收到此命令后可认为接入完成了,然后终端在RRC层上发重配完成消息(第9步)- RRC Connect Reconfiguration complete(HO Confirm)上报重配完成消息,切换完成- Release Resource当终端成功接入后,目标小区通知源小区删除终端的上下文信息四、协议对LTE事件的定义和说明4.1 A1事件定义Event A1 (Serving becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A1-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A1-1 (Entering condition)-Ms>HysThreshInequality A1-2 (Leaving condition)Ms<+ThreshHysThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a1-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.2 A2事件定义Event A2 (Serving becomes worse than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A2-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A2-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A2-1 (Entering condition)+Ms<HysThreshInequality A2-2 (Leaving condition)Ms>-HysThreshThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a2-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.3 A3事件定义Event A3 (Neighbour becomes offset better than PCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A3-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A3-2, as specifiedbelow, is fulfilled;NOTE The cell(s) that triggers the event is on the frequency indicated in the associated measObject which may be different from the (primary) frequency used by the PCell.Inequality A3-1 (Entering condition)++>+Mn++-OcnOfpOcpMpHysOffOfnInequality A3-2 (Leaving condition)++<Mn++++MpOcpOfnOfpOffHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Mp is the measurement result of the PCell, not taking into account any offsets.Ofp is the frequency specific offset of the primary frequency (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the primary frequency).Ocp is the cell specific offset of the PCell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the primary frequency), and is set to zero if not configured for the PCell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a3-Offset as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Ofp, Ocp, Hys, Off are expressed in dB.4.4 A4事件定义Event A4 (Neighbour becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A4-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A4-2, as specifiedbelow, is fulfilled;Inequality A4-1 (Entering condition)-+Mn>+HysThreshOcnOfnInequality A4-2 (Leaving condition)Mn<+++ThreshOfnHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a4-Threshold as defined within reportConfigEUTRA for this event).Mn is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.5 A5事件定义Event A5 (PCell becomes worse than threshold1 and neighbour becomes better than threshold2)The UE shall:1> consider the entering condition for this event to be satisfied when both condition A5-1 andcondition A5-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition A5-3 or conditionA5-4, i.e. at least one of the two, as specified below, is fulfilled;NOTE: The cell(s) that triggers the event is on the frequency indicated in the associated measObject which may be different from the (primary) frequency used by the PCell.Inequality A5-1 (Entering condition 1)+Mp<HysThresh1Inequality A5-2 (Entering condition 2)+-+Mn>Thresh2HysOcnOfnInequality A5-3 (Leaving condition 1)-Mp>HysThresh1Inequality A5-4 (Leaving condition 2)2++Mn<+OfnHysThreshOcnThe variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigEUTRA for this event).Thresh1 is the threshold parameter for this event (i.e. a5-Threshold1 as defined within reportConfigEUTRA for this event).Thresh2 is the threshold parameter for this event (i.e. a5-Threshold2 as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh1is expressed in the same unit as Mp.Thresh2is expressed in the same unit as Mn.Event A6 (Neighbour becomes offset better than SCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A6-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A6-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the (secondary) cell that is configured on the frequency indicatedin the associated measObjectEUTRA to be the serving cell;NOTE: The neighbour(s) is on the same frequency as the SCell i.e. both are on the frequency indicated in the associated measObject.Inequality A6-1 (Entering condition)+>Mn++-MsOcsOffHysOcnInequality A6-2 (Leaving condition)+<+Mn++OcsOffMsHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Ms is the measurement result of the serving cell, not taking into account any offsets.Ocs is the cell specific offset of the serving cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the serving frequency), and is set to zero if not configured for the serving cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a6-Offset as defined within reportConfigEUTRA for this event).Mn, Ms are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ocn, Ocs, Hys, Off are expressed in dB.Event B1 (Inter RAT neighbour becomes better than threshold)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when condition B1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition B1-2, as specifiedbelow, is fulfilled;Inequality B1-1 (Entering condition)Thresh+Mn>-HysOfnInequality B1-2 (Leaving condition)++Mn<ThreshHysOfnThe variables in the formula are defined as follows:Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA 2000 measurement result, pilotStrength is divided by -2.Ofn is the frequency specific offset of the frequency of the inter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the neighbour inter-RAT cell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh is the threshold parameter for this event (i.e. b1-Threshold as defined within reportConfigInterRAT for this event). For CDMA2000, b1-Threshold is divided by -2.Mn is expressed in dBm or in dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.8 B2事件定义Event B2 (PCell becomes worse than threshold1 and inter RAT neighbour becomes better than threshold2)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when both condition B2-1 andcondition B2-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition B2-3 or conditionB2-4, i.e. at least one of the two, as specified below, is fulfilled;Inequality B2-1 (Entering condition 1)+HysMp<Thresh1Inequality B2-2 (Entering condition 2)-+Mn>Ofn2ThreshHysInequality B2-3 (Leaving condition 1)Hys-Mp>1ThreshInequality B2-4 (Leaving condition 2)Mn<++OfnHys2ThreshThe variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA2000 measurement result, pilotStrength is divided by -2.Ofn is the frequency specific offset of the frequency of the inter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the inter-RAT neighbourcell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh1 is the threshold parameter for this event (i.e. b2-Threshold1 as defined within reportConfigInterRAT for this event).Thresh2 is the threshold parameter for this event (i.e. b2-Threshold2 as defined within reportConfigInterRAT for this event). For CDMA2000, b2-Threshold2 is divided by -2.Mp is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Mn is expressed in dBm or dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.Thresh1is expressed in the same unit as Mp.Thresh2is expressed in the same unit as Mn.第11页。

LTE A B切换事件

LTE A B切换事件

一、L T E切换事件系统内测量事件采用Ax来标识,系统内事件的报告各类:●eventA1:服务小区质量高于一个绝对门限(serving>threshold)。

用于关闭正在进行的频间测量,在RRC控制下去掉激活测量间隙(gap)事件进入条件:Ms-Hys>Thresh事件离开条件:Ms+Hys<Thresh其中Ms:为服务小区的测量结果,没有计算任何小区各自的偏置如果测量的是RSRP则单位为dBm,如果是RSRQ则单位为dB。

Hys:为此事件的滞后参数。

单位为dB。

取值范围(0-30)实际值=取值*0.5dBThresh:为此事件的门限参数。

单位同Ms一样●eventA2:服务小区质量低于一个绝对门限(serving<threshold)。

用于打开频间测量,在RRC控制下激活测量间隙(gap)。

事件进入条件:Ms+Hys<Thresh事件离开条件:Ms-Hys>Thresh●eventA3:邻小区比服务小区质量高于一个门限(Neighbour>Serving+Offset)用于频内/频间的基于覆盖的切换。

●事件进入条件:Mn+Ofn+Ocn-Hys>Ms+Ofs+Ocs+Off●事件离开条件:Mn+Ofn+Ocn+Hys<Ms+Ofs+Ocs+Off●其中●Mn:邻小区的测量结果,不考虑计算任何偏置。

●Ofn:该邻区频率特定的偏置(即offsetFreq在measObjectEUTRA中被定义为对应于邻区的频率)●Ocn:为该邻区的小区特定偏置(即cellIndividualOffset在measObjectEUTRA中被定义为对应于邻区的频率),同时如果没有为邻区配置,则设置为零。

●Ms:为没有计算任何偏置下的服务小区的测量结果。

●Ofs:为服务频率上频率特定的偏置(即offsetFreq在measObjectEUTRA中被定义为对应于服务频率)●Ocs:为服务小区的小区特定偏置(即cellIndividualOffset在measObjectEUTRA中被定义为对应于服务频率),并设置为0,如果没有为服务小区配置的话;●Hys:为该事件的滞后参数(即hysteres为reportConfigEUTRA内为该事件定义的参数)。

LTE事件——精选推荐

LTE事件——精选推荐

LTE事件⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划1.AttachAttempt附着尝试 UE发送Attach Request消息请求附着到数据业务。

⽹优⼈归乡计划2.AttachSuc附着成功 UE发送Attach Request消息后,在45秒内发送Attach Complete消息,表⽰附着数据业务成功。

⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划3.AttachFai附着失败 UE发送AttachRequest消息后,在45秒内未发送AttachComplete消息,表⽰附着数据业务失败。

⽹优⼈归乡计划⽹优⼈归乡⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划计划⽹优⼈归乡计划4.DetachAttempt去附着尝试 UE发送Detach Request消息或基站发送DetachRequest消息请求去附着到数据业务。

⽹优⼈归乡计⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归5.DetachSuc去附着成功 '以下情况表⽰UE去附着数据业务成功:UE向基站发送Detach Request消息后,在15秒内收到基站发出的Detach Accept消息; 基站向UE发送Detach Request消息后,在15秒内收到UE发出的Detach Accept消息'⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划6.RRCSetupReq RRC(Radio Resource Control)连接建⽴请求 UE发送RRC Connection Request消息请求建⽴RRC连接。

⽹优⼈归乡计划⽹优⼈归乡计划⽹优⼈归乡计划7.RRCSetupSuc RRC连接建⽴成功 MS发出RRCConnection Request,并且2.5s内UE发出RRC Connection Setup Complete,则触发该事件。

A1-B2事件 (LTE)

A1-B2事件 (LTE)

LTE支持的切换事件有A类和B类,其中A类本用作系统内测量,B类被用作系统间测量A1事件:表示服务小区信号质量高于一定门限;A2事件:表示服务小区信号质量低于一定门限;A3事件:表示邻区质量高于服务小区质量,用于同频、异频的基于覆盖的切换;A4事件:表示邻区质量高于一定门限,用于基于负荷的切换,可用于负载均衡;A5事件:表示服务小区质量低于一定门限并且邻区质量高于一定门限,可用于负载均衡; 异系统测量事件:B1事件:邻小区质量高于一定门限,用于测量高优先级的异系统小区;B2事件:服务小区质量低于一定门限,并且邻小区质量高于一定门限,用于相同或较低优先级的异系统小区的测量。

LTE移动性参数(全局)1最小接入电平基本信息参数名称(中文)参数名称(英文)取值范围单位最小接收电平QrxLevMin LTE (-140 (44)3G (-119 (25)2G (-115 (25)dBm缺省值开局建议值配置步长参数类型LTE:-1403G邻区频点:-119 2G邻区频点:-115LTE:-1223G:-1192G:-1152长整型影响范围修改生效方式参数出处适用制式LTE小区2G/3G邻区频点修改立即生效3GPP TS 36.331通用参数功能该参数表示UE在该小区驻留需满足的最小接收电平门限。

该值取值范围是2G/3G接收电平的实际值,对于LTE/3G , 实际的RxlevMin 等于SIB3/SIB6的IE value的两倍,调整步长为2dbm。

对于2G,实际的RxlevMin等于SIB7的 (IE value * 2) 115,调整步长为2dBm当UE测量到的2G/3G电平满足S准则时,UE才可能驻留在该小区。

参数调整影响调整该参数的门限值,会对小区的选择和驻留有所影响。

QrxLevMin如果设置过高,则UE将无法驻留到该小区。

2高优先级重选门限基本信息参数功能当高优先级小区的S值在一定时间内高于该阀值(threshXHigh)后,UE可以重选到该小区。

LTE常用事件详解

LTE常用事件详解

CSFBServiceFail
InterRATHOCmd InterRATHOSuc InterRATHOFail InterRATRedirectionReq InterRATRedirectionSuc InterRATRedirectionFail
RandomAccess
随机接入事件
给出的说明并进行相应的操作。 具体说明 UE发送Attach Request消息请求附着到数据业务。 UE发送Attach Request消息后,在45秒内发送Attach Complete消息,表示附着数据业务成功。 UE发送Attach Request消息后,在45秒内未发送Attach Complete消息,表示附着数据业务失败。 UE发送Detach Request消息或基站发送Detach Request 消息请求去附着到数据业务。 以下情况表示UE去附着数据业务成功: UE向基站发送Detach Request消息后,在15秒内收到 基站发出的Detach Accept消息。 基站向UE发送Detach Request消息后,在15秒内收到 UE发出的Detach Accept消息。 UE发送RRC Connection Request消息请求建立RRC连接。
MS发出RRC Connection Request,并且2.5s内UE发出RRC Connection Setup Complete,则触发该事件。 MS发出RRC Connection Request,并且2.5s内UE没有发 出RRC Connection Setup Complete,或者收到RRC Connection Reject,则触发该事件。 如果RRC Connection Reconfiguration消息中包含特定 的信元(“drb-ToAddModList”或“drbToAddModifyList”),并且不包含信元“ mobilityControlInfo”,表示ERAB建立尝试。 ERABSetupAttempt事件发生后,UE在1秒内收到RRC Connection Reconfiguration Complete消息,并且消息 中的信元“RRC-TransactionIdentifier”值与信元“ RRC Connection Reconfiguration”信元值相同,则表 示ERAB建立成功。 以下情况表示ERAB建立失败: ERABSetupAttempt事件发生后,1秒内UE没有收到RRC Connection Reconfiguration Complete消息。 ERABSetupAttempt事件发生后,UE收到 RRCConnectionReestablishmentRequest消息。 以下情况表示ERAB正常释放: UE收到Deactivate Eps Bearer Context Request消 息后,收到了RRC Connection Reconfiguration消 息,且消息中有信元“drb-ToReleaseList”。 UE收到Deactivate Eps Bearer Context Request消 息后,收到了RRC Connection release消息。 UE收到MME的DETACH REQUEST消息,或者向网络侧主 动发出DETACH REQUEST消息后收到RRC release消息

LTE事件汇总表

LTE事件汇总表

含义 附着尝试 附着成功 附着失败 去附着尝试
去附着成功
RRC(Radio Resource Control)连接建立请求 RRC连接建立成功 RRC连接建立失败 ERAB(Evolved Radio Access Bearer)建立尝试
ERAB建立成功
ERAB建立失败
ERAB正常释放
ERABAbnormalRel
系统收到UE发送的TRACKING AREA UPDATE REQUEST消息则判断一次TA Update Attempt。 UE发送TRACKING AREA UPDATE REQUEST消息后,规定时间内收到TRACKING AREA UPDATE ACCEPT或TRACKING AREA UPDATE Complete消息,则表示LTE TA更新成功。 以下情况都表示LTE TA更新失败:
CSFBServiceSuc
CSFBServiceFail
InterRATHOCmd
InterRATHOSuc InterRATHOFail InterRATRedirectionReq InterRATRedirectionSuc InterRATRedirectionFail
LTE到GSM小区重选事件 LTE到WCDMA小区重选事件 GSM到LTE小区重选事件 WCDMA到LTE小区重选事件 CSFB服务请求
TAUpdateFail
同频切换失败
TA更新请求 TA更新成功
TA更新失败
TAUpdateFail
TA更新失败
Data Transfer Start Data Transfer End Session Start Session End
开始数据传输 数据传输结束事件 任务开始执行事件 任务结束事件

LTE A1-A5 B1-B2事件

LTE A1-A5 B1-B2事件

LTE支持的切换事件有A类和B类,其中A类被用作系统内测量,B类被用作系统间测量B1:邻小区比绝对门限好。

用于测量高优先级的RAT小区B2:服务小区比绝对门限1差,邻小区比绝对门限2好,用于相同或者低优先级的RAT 小区的测量LTE切换时需要UE上报测量的结果(包括RSRP,RSRQ等),而上报又分为周期性上报和事件触发的上报。

周期性上报由基站配置,UE直接上报测量的结果。

事件触发的上报又分为同频系统的事件和不同系统间的事件:同频切换报告事件包括:1. 事件A1,服务小区好于绝对门限;这个事件可以用来关闭某些小区间的测量。

2. 事件A2,服务小区差于绝对门限;这个事件可以用来开启某些小区间的测量,因为这个事件发生后可能发生切换等操作。

3. 事件A3,邻区好于服务小区;这个事件发生可以用来决定UE是否切换到邻区4. 事件A4,邻区好于绝对门限;5. 事件A5,服务小区差于一个绝对门限并且邻区好于一个绝对门限;这个事件也可以用来支持切换Intra-Frequency-HO切换都是基于A3/A5事件进行的切换A3事件:邻区的服务质量(RSRP/RSRQ)比服务小区高一个绝对门限,触发A3事件切换。

A5事件:服务小区的服务质量低于一个绝对门限1,邻区的服务质量高于一个绝对门限2,触发A5事件切换。

1.A3或A5事件触发。

2.Source eNB 向UE发送mearsurement control 4q;d6C1[1m+_,M+N1j:l3.Source eNB 向UE发送UL allocation MSG4.UE向Source eNB发送Measurement report MSG5.Source eNB内部进行HO decision6.Source eNB向Target eNB发送Handover request MSG7.Target eNB内部进行Admission controlMSCBSC 移动通信论坛,x"w3Q)j'V8.Target eNB向Source eNB回复Handover request ack MSG 9.Source eNB向UE回复DL allocation MSG10.Source eNB向UE发送RRC Connection reconfiguration MSGMSCBSC 移动通信论坛.k)C1b7\)C+x7W(j11.UE与Source eNB进行Detach,并开始同步到Target eNB12.Source eNB进行缓存控制并向Target eNB传送数据包以及进行SN status transfer (序列数转移)13.Source eNB向Target eNB进行数据转移传送"T/`2L4F [:u*v14.UE与Target eNB同步完成MSCBSC 移动通信论坛$b1e3x3~"X G8A15.Target eNB向UE发送UL Allocation+TA UE MSG16.UE向Target eNB发送RRC connection complete MSG 17.UE与Target eNB,Target eNB与S-GW之间进行数据交互;Q:u5O&m)F1h18.Target eNB向MME发起Path switch request 19.MME向S-GW发起user plane update requestMSCBSC 移动通信论坛!w!P,U5c5}3T5y9H20.S-GW与Source eNB进行Switch DL Path,并发起End marker MSGmscbsc 移动通信论坛拥有30万通信专业人员,超过50万份GSM/3G等通信技术资料,是国内领先专注于通信技术和通信人生活的社区。

LTE切换事件介绍

LTE切换事件介绍
当两个小区SINR值都较高时,应使UE尽量占用D 频段小区;
在不影响切换及时性时,应尽量减小A1、A2门限, 以避免因异频测量导致的上下行调度次数降低;
为方便理解A1、A2门限,请看下 图:
假设UE占用A小区,且A小区异频A1 RSRP触发门限、异频A2 RSRP触发 门限分别设置为-88、-90(系统默认), A1、A2事件迟滞参数设置为2(系 统默认)。
Mn + Ofn + Ocn - Hys(4) > Thersh(4) 其中:
Mn:邻小区测量结果 Ofn:邻小区频率特定的偏差,默认为0 Ocn:邻小区个性偏移(CIO) Hys(4):A4事件迟滞参数 Thersh(4):A4事件门限参数
A1、A2、A4门限参数设置应遵循以下几个原则:
应使UE尽量占用RSRP值、SINR值较高的小区, 如果遇到RSRP值、SINR值都较高无法满足的情况时, 应使UE尽量占用SINR值较高的小区;
A5事件的切换参数配置
事件A5的触发条件:即服务小区的质量已经低于一定门限值1,且邻区质 量高于一定门限值2。
A5事件判决公式 触发条件:Ms + Hys(5) < Thresh1 且 Mn + Ofn + Ocn – Hys (5)> Thresh2 取消条件:Ms - Hys(5) > Thresh1 或 Mn + Ofn + Ocn + Hys (5) < Thresh2 其中:
Ms:服务小区测量结果 Hys(1):A1事件迟滞参数 Hys(2):A2事件迟滞参数 Thersh(1):A1事件门限参数 Thersh(2):A2事件门限参数
A2事件的切换参数配置

LTE事件分析详解

LTE事件分析详解

U E收到Deactivate Eps Bearer Context Request消息后,收到了RRC Con 以下情况表示ERAB正常释放:如果第k条和第k+1条切换A3事件时间小于1s,且之间没有切换命令,统计为一次HOPrepareAttempt。

如果第k条和第k+1条切换A3事件时间小于1s,且之间有切换命令,切换准备尝试次数+1。

据业务成功。

示附着数据业务失败。

基站向UE发送Detach Request消息后,在15秒内收到UE发出的De 后,在15秒内收到基站发出的Detach Accept消息。

p Complete,则触发该事件。

Setup Complete,或者收到RRC Connection Reject,则触发该事件。

ddModList”或“drb-ToAddModifyList”),并且不包含信元“mobilityControlInfo”,表示ERAB建立尝试。

ration Complete消息,并且消息中的信元“RRC-TransactionIdentifier”值与信元“RRC Connection ReconfiguE RABSetupAttempt事件发生后,UE收到RRCConnectionRees 收到RRC Connection Reconfiguration Complete消息。

U E收到Dea uest消息后,收到了RRC Connection Reconfiguration消息,且消息中有信元“drb-ToReleaseList”。

REQUEST消息和MME的DETACH REQUEST消息,也没有向网络侧主动发出DETACH REQUEST消息,但收到了RRCConnecti到UE发出的Detach Accept消息示ERAB建立尝试。

onnection Reconfiguration”信元值相同,则表示ERAB建立成功。

到RRCConnectionReestablishmentRequest消息。

LTE常见事件以及解析

LTE常见事件以及解析

名称含义具体说明AttachAttempt 附着尝试 UE发送Attach Request消息请求附着到数据业务。

AttachSuc 附着成功 UE发送Attach Request消息后,在45秒内发送Attach Complete消息,表示附着数据业务成功。

AttachFail 附着失败 UE发送Attach Request消息后,在45秒内未发送Attach Complete消息,表示附着数据业务失败。

DetachAttempt 去附着尝试 UE发送Detach Request消息或基站发送Detach Request消息请求去附着到数据业务。

DetachSuc 去附着成功 "以下情况表示UE去附着数据业务成功:UE向基站发送Detach Request消息后,在15秒内收到基站发出的Detach Accept消息。

基站向UE发送Detach Request消息后,在15秒内收到UE发出的Detach Accept消息" RRCSetupReq RRC(Radio Resource Control)连接建立请求 UE发送RRC Connection Request消息请求建立RRC连接。

RRCSetupSuc RRC连接建立成功 MS发出RRC Connection Request,并且2.5s 内UE发出RRC Connection Setup Complete,则触发该事件。

RRCSetupFail RRC连接建立失败 MS发出RRC Connection Request,并且2.5s 内UE没有发出RRC Connection Setup Complete,或者收到RRC Connection Reject,则触发该事件。

ERABSetupAttempt ERAB(Evolved Radio Access Bearer)建立尝试如果RRC Connection Reconfiguration消息中包含特定的信元(“drb-ToAddModList”或“drb-ToAddModifyList”),并且不包含信元“mobilityControlInfo”,表示ERAB建立尝试。

LTE的9种传输模式和7个切换事件

LTE的9种传输模式和7个切换事件

LTE的9种传输模式:
1. TM1,单天线端口传输:主要应用于单天线传输的场合
2. TM2,开环发射分集:不需要反馈PMI,适合于小区边缘信道情况比较复杂,干扰较大的情况,
有时候也用于高速的情况,分集能够提供分集增益
3. TM3,开环空间复用:不需要反馈PMI,合适于终端(UE)高速移动的情况
4. TM4,闭环空间复用:需要反馈PMI,适合于信道条件较好的场合,用于提供高的数据率传输
5. TM5,MU-MIMO传输模式(下行多用户MIMO):主要用来提高小区的容量
6. TM6,闭环发射分集,闭环Rank1预编码的传输:需要反馈PMI,主要适合于小区边缘的情况
7. TM7,Port5的单流Beamforming模式:主要也是小区边缘,能够有效对抗干扰
8. TM8
9.
✍事件eNodeB ✍事件eNodeB ✍事件
✍事件启✍事件
✍事件eNodeB ✍事件。

LTE系统事件简介

LTE系统事件简介

LTE系统事件简介一、LTE事件概述LTE切换时需要UE上报测量的结果(包括RSRP,RSRQ等),而上报又分为周期性上报和事件触发的上报。

➢周期性上报由基站配置,UE直接上报测量的结果。

➢事件触发的上报又分为系统内的事件和系统间的事件。

LTE系统内切换主要事件包括:➢A1事件,服务小区质量高于门限;这个事件可以用来关闭频间测量。

➢A2事件,服务小区质量低于门限;这个事件可以用来打开频间测量和系统间测量,因为这个事件发生后可能发生切换等操作。

➢A3事件,邻小区质量好于服务小区质量;这个事件一般用于频内/间基于覆盖的切换。

➢A4事件,邻小区质量好于门限;这个事件一般用于基于负荷的切换。

➢A5事件,服务小区质量低于一个门限并且邻小区质量高于一个门限;这个事件也可以用于频内/间基于覆盖的切换。

目前LTE同频切换都是基于A3/A5事件进行的切换(现网主要是基于A3事件的)二、切换流程举例三、切换流程简要说明- RRC Connection Reconfiguration(Measurement Control)测量控制,一般在初始接入或上一次切换命令中的重配消息里携带- Measurement Report测量报告,终端根据当前小区的测量控制信息,将符合切换门限的小区进行上报- HO Request源小区在收到测量报告后向目标小区申请资源及配置信息(站内切换的话为站内交互,站间切换会使用X2口或者S1口,优先使用X2口)- HO Request Ack目标小区将终端的接纳信息以及其它配置信息反馈给源小区- RRC Connection Reconfiguration(HO Command)将目标小区的接纳信息及配置信息发给终端,告知终端目标小区已准备好终端接入,重配消息里包含目标小区的测量控制- SN Status Transfer源小区将终端业务的缓存数据移至目标小区- Random Access Preamble终端收到第5步重配消息(切换命令)后使用重配消息里的接入信息进行接入- Random Access Response目标小区接入响应,收到此命令后可认为接入完成了,然后终端在RRC层上发重配完成消息(第9步)- RRC Connect Reconfiguration complete(HO Confirm)上报重配完成消息,切换完成- Release Resource当终端成功接入后,目标小区通知源小区删除终端的上下文信息四、协议对LTE事件的定义和说明4.1 A1事件定义Event A1 (Serving becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A1-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A1-1 (Entering condition)-Ms>HysThreshInequality A1-2 (Leaving condition)Ms<+ThreshHysThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a1-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.2 A2事件定义Event A2 (Serving becomes worse than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A2-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A2-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A2-1 (Entering condition)+Ms<HysThreshInequality A2-2 (Leaving condition)Ms>-HysThreshThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a2-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.3 A3事件定义Event A3 (Neighbour becomes offset better than PCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A3-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A3-2, as specifiedbelow, is fulfilled;NOTE The cell(s) that triggers the event is on the frequency indicated in the associated measObject which may be different from the (primary) frequency used by the PCell.Inequality A3-1 (Entering condition)++>+Mn++-OcnOfpOcpMpHysOffOfnInequality A3-2 (Leaving condition)++<Mn++++MpOcpOfnOfpOffHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Mp is the measurement result of the PCell, not taking into account any offsets.Ofp is the frequency specific offset of the primary frequency (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the primary frequency).Ocp is the cell specific offset of the PCell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the primary frequency), and is set to zero if not configured for the PCell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a3-Offset as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Ofp, Ocp, Hys, Off are expressed in dB.4.4 A4事件定义Event A4 (Neighbour becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A4-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A4-2, as specifiedbelow, is fulfilled;Inequality A4-1 (Entering condition)-+Mn>+HysThreshOcnOfnInequality A4-2 (Leaving condition)Mn<+++ThreshOfnHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a4-Threshold as defined within reportConfigEUTRA for this event).Mn is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.5 A5事件定义Event A5 (PCell becomes worse than threshold1 and neighbour becomes better than threshold2)The UE shall:1> consider the entering condition for this event to be satisfied when both condition A5-1 andcondition A5-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition A5-3 or condition A5-4, i.e. at least one of the two, as specified below, is fulfilled;NOTE: The cell(s) that triggers the event is on the frequency indicated in the associatedmeasObject which may be different from the (primary) frequency used by the PCell.Inequality A5-1 (Entering condition 1)1Thresh Hys Mp <+Inequality A5-2 (Entering condition 2)2Thresh Hys Ocn Ofn Mn >-++Inequality A5-3 (Leaving condition 1)1Thresh Hys Mp >-Inequality A5-4 (Leaving condition 2)2Thresh Hys Ocn Ofn Mn <+++The variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh1 is the threshold parameter for this event (i.e. a5-Threshold1 as defined within reportConfigEUTRA for this event).Thresh2 is the threshold parameter for this event (i.e. a5-Threshold2 as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh1 is expressed in the same unit as Mp .Thresh2 is expressed in the same unit as Mn .Event A6 (Neighbour becomes offset better than SCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A6-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A6-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the (secondary) cell that is configured on the frequency indicatedin the associated measObjectEUTRA to be the serving cell;NOTE: The neighbour(s) is on the same frequency as the SCell i.e. both are on the frequency indicated in the associated measObject.Inequality A6-1 (Entering condition)+>Mn++-MsOcsOffHysOcnInequality A6-2 (Leaving condition)+<+Mn++OcsOffMsHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Ms is the measurement result of the serving cell, not taking into account any offsets.Ocs is the cell specific offset of the serving cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the serving frequency), and is set to zero if not configured for the serving cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a6-Offset as defined within reportConfigEUTRA for this event).Mn, Ms are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ocn, Ocs, Hys, Off are expressed in dB.Event B1 (Inter RAT neighbour becomes better than threshold)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when condition B1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition B1-2, as specifiedbelow, is fulfilled;Inequality B1-1 (Entering condition)Thresh+Mn>-HysOfnInequality B1-2 (Leaving condition)++Mn<ThreshHysOfnThe variables in the formula are defined as follows:Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA 2000 measurement result, pilotStrength is divided by -2.Ofn is the frequency specific offset of the frequency of the inter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the neighbour inter-RAT cell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh is the threshold parameter for this event (i.e. b1-Threshold as defined within reportConfigInterRAT for this event). For CDMA2000, b1-Threshold is divided by -2.Mn is expressed in dBm or in dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.8 B2事件定义Event B2 (PCell becomes worse than threshold1 and inter RAT neighbour becomes better than threshold2)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when both condition B2-1 andcondition B2-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition B2-3 or conditionB2-4, i.e. at least one of the two, as specified below, is fulfilled;Inequality B2-1 (Entering condition 1)+HysMp<Thresh1Inequality B2-2 (Entering condition 2)-+Mn>Ofn2ThreshHysInequality B2-3 (Leaving condition 1)Hys-Mp>1ThreshInequality B2-4 (Leaving condition 2)Mn<++OfnHys2ThreshThe variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA2000 measurement result, pilotStrength is divided by -2.Ofn is the frequency specific offset of the frequency of the inter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the inter-RAT neighbourcell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh1 is the threshold parameter for this event (i.e. b2-Threshold1 as defined within reportConfigInterRAT for this event).Thresh2 is the threshold parameter for this event (i.e. b2-Threshold2 as defined within reportConfigInterRAT for this event). For CDMA2000, b2-Threshold2 is divided by -2.Mp is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Mn is expressed in dBm or dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.修正版Thresh1 is expressed in the same unit as Mp. Thresh2 is expressed in the same unit as Mn.。

相关主题
  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

eNodeB发送的RRC Connection Reconfiguration消息中 包含了信元“mobility ControlInfo ”且“dlCarrierFreq”的值与当前“Serving EARFCN”的值不相 同,表示UE尝试异频切换。 以下情况表示UE异频切换成功: InterFreqHOAttempt事件发生后,UE在t304+1000ms 内收到新的小区发送的RRC Connection Reconfiguration消息。 InterFreqHOAttempt事件发生后,在t304+1000ms内 UE的“RRC State”值为“Connected”且当前的“ Serving PCI”值为切换请求消息中的“ targetPhysCellId”值。 InterFreqHOAttempt事件发生后,UE在t304+1000ms 内遇到TUE及**(某品牌)的终端内部事件HandoverSuc 说明: t304为协议中的定时器,表示切换请求到切换完成的超 时时间,协议规定最大时长为2s。 以下情况表示UE异频切换失败: InterFreqHOAttempt事件发生后,eNodeB在新的小区 发送RRC Connection Reconfiguration消息前收到 RRC Connection Reestablishment Request消息或 RRC Connection Release消息。 InterFreqHOAttempt事件发生后,UE的“RRC State ”值为“Idle”。 发生同频切换尝试事件后,在t304+1000ms时间内 Serving PCI没有更新为切换请求消息中的 targetPhysCellId。 在t304时间内遇到TUE及**(同上某品牌)的终端内部 事件HandoverFail。 eNodeB发送的RRC Connection Reconfiguration消息中 包含了信元“mobility ControlInfo ”且“dlCarrierFreq”的值与当前“Serving EARFCN”的值相 同,表示UE尝试同频切换。 以下情况表示UE同频切换成功: IntraFreqHOAttempt事件发生后,UE在t304+1000ms 内收到新的小区发送的RRC Connection Reconfiguration消息。 IntraFreqHOAttempt事件发生后,在t304+1000ms内 UE的“RRC State”值为“Connected”且当前的“ Serving PCI”值为切换请求消息中的“ targetPhysCellId”。 IntraFreqHOAttempt事件发生后,UE在t304+1000ms 内遇到TUE及**(同上品牌)的终端内部事件 HandoverSuc。 以下情况表示UE同频切换失败:
HOPrepareAttempt
通过切换A3事件统计 切换准备尝试次数。
InterFreqHOAttempt
异频切换尝试
InterFreqHOSuc
异频切换成功
InterFreqHOFail
异频切换失败
IntraFreqHOAttempt
同频切换尝试
IntraFreqHOSuc
同频切换成功
IntraFreqHOFail
RRC(Radio Resource Control) 连接建立请求 RRC连接建立成功 RRC连接建立失败 ERAB(Evolved Radio Access Bearer)建立尝试
ERABSetupAttempt
ERABSetupSuc
ERAB建立成功
ERABSetupFail
ERAB建立失败
ERABNormalRel
CellReselectionL2W CellReselectionG2L CellReselectionW2L CSFBServiceRequest CSFBServiceSuc
LTE到WCDMA小区重选 事件 GSM到LTE小区重选事 件 WCDMA到LTE小区重选 事件 CSFB服务请求 CSFB接入成功事件 LTE回落到GU失败事 件 LTE异系统切换命令 LTE异系统切换成功 事件 LTE异系统切换失败 事件 LTE异系统重定向请 求 LTE异系统重定位成 功事件 LTE异系统重定位失 败事件
同频切换失败
TAUpdateAttempt TAUpdateSuc
TA更新请求 TA更新成功
TAUpdateFail
TA更新失败
Data Transfer Start Data Transfer End Session Start Session End
开始数据传输 数据传输结束事件 任务开始执行事件 任务结束事件
CSFBServiceFail
InterRATHOCmd InterRATHOSuc InterRATHOFail InterRATRedirectionReq InterRATRedirectionSuc InterRATRedirectionFail
RandomAccess
随机接入事件
给出的说明并进行相应的操作。 具体说明 UE发送Attach Request消息请求附着到数据业务。 UE发送Attach Request消息后,在45秒内发送Attach Complete消息,表示附着数据业务成功。 UE发送Attach Request消息后,在45秒内未发送Attach Complete消息,表示附着数据业务失败。 UE发送Detach Request消息或基站发送Detach Request 消息请求去附着到数据业务。 以下情况表示UE去附着数据业务成功: UE向基站发送Detach Request消息后,在15秒内收到 基站发出的Detach Accept消息。 基站向UE发送Detach Request消息后,在15秒内收到 UE发出的Detach Accept消息。 UE发送RRC Connection Request消息请求建立RRC连接。
Session Drop
任务异常结束事件
Session Error RRCReestablishAttempt RRCReestablishSuc
任务失败事件 RRC重建请求 RRC重建成功
RRCReestablishFail
RRC重建失败
CellReselectionL2G
LTE到GSM小区重选事 件
的说明。在配置LTE网络的事件时,可以参考此处给出的说明并进行相应的操作。 名称 AttachAttempt AttachSuc AttachFail DetachAttempt 含义 附着尝试 附着成功 附着失败 去附着尝试
DetachSuc
去附着成功
RRCSetupReq RRCSetupSuc RRCSetupFail
UE没有收到DEACTIVATE EPS BEARER CONTEXT REQUEST消息和MME的DETACH REQUEST消息,也没有向 网络侧主动发出DETACH REQUEST消息,但收到了 RRCConnection release消息并且前4s没有APP层速率 传输。 以下情况表示ERAB异常释放: UE没有收到DEACTIVATE EPS BEARER CONTEXT REQUEST消息和MME的DETACH REQUEST消息,也没有向 网络侧主动发出DETACH REQUEST消息,但收到了 RRCConnectionReconfiguration消息,且其中有信元 “drb-ToReleaseList”。 UE没有收到DEACTIVATE EPS BEARER CONTEXT REQUEST消息和MME的DETACH REQUEST消息,也没有向 网络侧主动发出DETACH REQUEST消息,但收到了 RRCConnection release消息并且前4s没有APP层速率 传输。 UE收到包含了信元“drb-ToAddModList”的RRC Connection Reconfiguration消息后,收到RRC释放 信令之前,UE的“RRCState”值为“Idle”。 在UE没有收到RRC Connection Reconfiguration消息 、EACTIVATE EPS BEARER CONTEXT REQUEST、DETACH REQUEST消息、RRC State、RRCConnection release 消息时,收到RRC的业务请求。 在UE没有收到RRC Connection Reconfiguration消息 、EACTIVATE EPS BEARER CONTEXT REQUEST、DETACH REQUEST消息、RRC State、RRCConnection release 消息时,收到RRCReestablishFail信息,触发本事件 服务小区的RSRP值比绝对门限阈值高时,输出A1测量报 服务小区的RSRP值比绝对门限阈值低时,输出A2测量报 邻区的RSRP值比服务小区的RSRP值高时,输出A3测量报 邻区的RSRP值比绝对门限阈值高时,输出A4测量报告。 服务小区的RSRP值比绝对门限阈值1低且邻区的RSRP值比 绝对门限阈值2高时,输出A5测量报告。 邻区的RSRP值比绝对门限阈值高时,输出B1测量报告。 服务小区的RSRP值比绝对门限阈值1低且邻区的RSRP值比 绝对门限阈值2高时,输出B2测量报告。 如果MeasurementReport消息中的“measId”与上一条 RRC Connection Reconfiguration消息中的“measId” 相同,则输出一次切换A3测量报告。 统计方法如下: 如果第k条和第k+1条切换A3事件时间小于1s,且之间 没有切换命令,统计为一次HOPrepareAttempt。 如果第k条和第k+1条切换A3事件时间小于1s,且之间 有切换命令,切换准备尝试次数+1。 如果第k条和第k+1条切换A3事件时间大于1s,则切换 准备尝试次数+1。
相关文档
最新文档