EZ-1000PLUS
Guardian 1000 Series Hipot Testers 产品介绍说明书
Guardian 1000 Series Hipot TestersIntroductionA complete dielectric testing solution, with three models from which to choose. The Guardian 1010 for AC Hipot testing, the Guardian 1030 for AC/DC Hipot testing and insulation resistance (IR) measurements; and the Guardian 1030S which combines both AC and DC Hipot tests and IR measurements with eight HV scan channels. All models have Open/Short Circuit detection and Load/Line regulation to ensure proper device connection and measurement integrity. The digital display and user friendly controls allow test parameters and limits to be set without the high voltage activated.DescriptionThe Guardian 1010 AC Hipot Tester performs AC dielectric withstand tests. The test voltage can be programmed in the range from 50V AC to 5kV AC with a resolution of 1V . The maximum total output current is 30mA.The Guardian 1030 AC/DC/IR Hipot Tester has all the features of the Guardian 1010 with the addition of DC hipot and IR measurement capabilities. The test voltage can be programmed in the range from 50VDC to 6kVDC with a resolution of 1V . The maximum total current is 10mA. The IR measurement range is from 0.1M Ωto 50G Ωwith test voltages from 50 to 1000VDC.The Guardian 1030S AC/DC/IR/SC Hipot Tester has all of the features of the Guardian1030 plus eight HV Scan Channels for multi-point testing.Real and Total Current Measurement:Accurately measure the leakage current of highly capacitive devices by separating the real and reactive current.Ground Fault Interrupt (GFI):Provides an extra level of safety for the operator and equipment. The instrument shuts down when the current balance exceeds 0.5mA.G1000 Series units also have an interlock for use with palm switches, light curtains,hoods and other safety switches.Quick DUT Discharge:In both the DC hipot and IR tests the device under test is dis-charged back through the HV transformef for a rapid and safe discharge.Ground Continuity Check:All of the Guardian 1000 Series units have a ground con-tinuity check feature to determine that the resistance, between the ground blade of the power cord and any exposed metal on the product, is less than 1 ohm.Open/Short Circuit Mode:All Guardian 1000 Series models have OS mode to detect connection of the device in order to prevent false readings. Open ensures the device under test is connected properly and Short ensures the device is not shorted prior to applying the high voltage. The Open value is programmable from 10-100% and the Short value from 100-500%.Multi-Purpose AC/DC/IR/SC Hipot TestersG1030S: EMC onlyFor more detailed information on specifications, pricing and special purchase, rent and lease options,contact us at:800-253-1230Hipot Testers • LCR Meters • Cable Testers • AC/DC Programmable Power Sources• Megohmmeters • Milliohmmeters1981Guardian 1010 AC Hipot TesterGuardian 1030 AC/DC/IR Hipot Tester Guardian 1030S AC/DC/IR/SC Hipot Tester Includes:150665Instruction Manual 700070Power Cable S02Test Leads 700100Ground Continuity Lead Calibration Certificate Traceable to NIST Lead Set: (8) Unterminated (1030S only)Optional Accessories:Calibration Data S02HV Lead Set, 1m, (std w/unit)S03Corded Product Adapter(115V)S04HV Lead Set, 2m S05Foot Switch S06High Voltage Probe S07Power Entry Adapter Cable S08Gun Probe S09HV Lead, 1 meter, unterminated S10HV Lead, 2 meters, unterminatedS11Gun Probe with remote start S12Load Box, resistiveS14Load Box, custom resistors S15Interconnection Cable to S50G16International Power StripG25Corded Product Adapter (240V)G38Printer Interface(replaces IEEE)G39IEEE-488 InterfaceG40Scanner Lead Set (8), with Clips for G1030S onlyOrdering InformationFor more detailed information on specifications, pricing and special purchase, rent and lease options, contact us at: or 800-253-1230P/N 030093/A6。
ICE-1000内核DM-HPUSB5.0Plus仿真器中文使用说明书
Blackfin+属于亚德诺半导体公司的商标 All other brand and product names are trademarks or service marks of their respective owners.
所有品牌和产品名称都有各自的商标或服务标志
Regulatory Compliance 遵从规章制度
ICE-1000/ICE-2000 仿真器的设计只适用于实验室环境。仿真器并非消费者的终端产品，也 不是消费者终端产品的一部分。仿真器是一个开放式系统设计，它不是屏蔽式的，因此可 能会对相邻的其他电气设备造成干扰。这个板不应使用或接近任何医疗设备或射频设备。。
更多有关亚德诺半导体仿真器的资讯，请浏览以下网页：
/processors/tools
ICE-1000/ICE-2000 Emulator User’s Guide
7
Purpose of This Manual
Purpose of This Manual
本手册的目的
ICE-1000/ICE-2000 仿真器用户通过使用说明书，在计算机上正确安装 仿真器的软硬件。
Intended Audience
本手册旨在帮助客户了解仿真器的功能和操作,这样他们就可以开始 使用 CrossCore Embedded Studio (CCES)和 VisualDSP + +
亚德诺半导体对模拟设备的应用程序，自定义产品设计，自定义软 件性能，专利侵权，服务描述不承担任何责任。此外，亚德诺半导体 公司不承担因使用本产品而产生的特殊的间接的造成附带的设备或性 能损害。
亚德诺半导体产品不适用于维持生命的应用程序、设备或者系统。未经亚德 诺半导体书面同意，禁止在这些应用方面使用亚德诺半导体产品。
oase 1000 Aquarius Universal Classic 用户手册说明书
Manuals+— User Manuals Simplified.oase 1000 Aquarius Universal Classic User Manual Home » Oase » oase 1000 Aquarius Universal Classic User ManualOperating instructionsAquarius Universal Classic1000 / 12 V, 2000 / 12 VWARNINGDisconnect all electrical devices in the water from the power supply before reaching into the water. Otherwise there is a risk of severe injuries or death by electrocution.This unit can be used by children aged 8 and above and by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they are supervised or have been instructed on how to use thepacemakers or implantable cardioverter defibrillators (ICDs). Keep a distance of at least 0.2 m between the implant and the magnet.Do not carry or pull the unit by its power cable.Route lines in such a way that they are protected from damage and do not present a tripping hazard.Never carry out technical changes to the unit.Only carry out work on the unit that is described in this manual.Only use original spare parts and accessories.Should problems occur, please contact the authorised customer service or OASE.Intended useOnly use the product described in this manual as follows:For pumping water, e.g. for water features.For use in swimming ponds if the national regulations for installers are met.Indoors and outdoors.Only operate with original transformer.While adhering to the technical specifications. (→ Technical data)Adherence to the permissible water quality. (→ Permissible water quality)The following restrictions apply to the unit:Never use the unit with fluids other than water.Never run the unit without water.Do not use in conjunction with chemicals, foodstuff, easily flammable or explosive substances.Do not connect to the domestic water supply.Do not use for commercial or industrial purposes.According to EMC (Electromagnetic Compatibility), this is a class A unit. The unit may cause malfunctions in living environments. It is the user’s responsibility to take suitable countermeasures.Product DescriptionOverview1. Inlet (suction side)• With filter cage (3) for submerged installation.• With hose sleeve for connecting a hose for dry installation.2. Outlet (pressure side)• Connection of the return line (e.g. to a fountain)3. Filter cage4. Flow rate controller5. Transformer with power cable• Pump power supply6. Stepped hose adapterSymbols on the unitInstallation variantsVariant (a): Submerged pump installation(→ Permissible water quality)WARNINGThe transformer is subject to dangerous voltage and must not be installed directly adjacent to the water. Otherwise there is a risk of severe injuries or death by electrocution.Install the transformer at a distance of at least 2 m from the water to ensure that it is protected againstflooding.NOTEElectrical screw connections …must always be tightened hand-tight to ensure correct contact and so that they comply with the protection class listed in the technical data.are protected against splash water but must not be placed or submerged in water.NOTEIf the pump is used for conveying excessively soiled water, the impeller unit will be subject to increased wear and will require earlier replacement.Thoroughly clean the pond or pool before installing the pump.Install the pump at a raised level above the bottom. This reduces intake of muddy water.Avoid direct sunlight on unit components that are not submerged, as they may overheat. If necessary, use a protective cover.Turning the pump inletThe pump inlet can be moved to the required orientation.Orientation UseTop or side (right, left)• Recommended for dry installation.• When used with submerged installation, ensure that the w ater level is sufficient.Bottom • Recommended for submerged installation.• Pumps water even when the water level is low.Submerged installation of the pump ConnectingDo not plug the power plug into the socket yet! InstallationPlace the pump horizontally on a stable, mud-free surface.Ensure secure and stable positioning of the pump.Only operate the pump when it is fully submerged.Do not plug the power plug into the socket yet!InstallationPlace the pump horizontally on a stable, mud-free surface.Ensure secure and stable positioning of the pump. Commissioning/start-upPrevent the pump from running dry. Otherwise the pump will be destroyed.Only operate the pump when it is submerged or flooded.Switching ON/OFFCAUTIONRisk of injury due to unexpected start-up. Internal monitoring functions may switch off the unit and automatically reactivate it.Disconnect the power plug before carrying out any work on the unit.NOTEfunction of the device and harm animals, plants and the environment.If possible, clean the unit with clear water and a soft brush or a sponge; remove stubborn dirt with the aid of Cleaning the deviceClean the unit as required but at least twiceper year.Storage/winter protectionShut down the unit at water temperatures below +4 °C or at the latest when freezing temperatures are expected. Malfunction remedyMalfunction Cause RemedyPump does not start No mains voltage Check the mains voltage.Supply lines kinked Route the supply lines without kinks Supply lines blocked.Check/clean the supply linesImpeller unit is blockedRemove blockage, check impeller unit forease of movementPump does not transport fluidIn sufficient flow rate Flow rate is set too low on the controllerIncrease flow rate on the controllerFilter housing clogged Clean strainer casingsExcessive loss in the supplylinesReduce hose length to the necessary minimum, removeunnecessary connection partsImpeller unit is running sluggishly Check impeller unit for ease of movementPump switches off after operati ngbriefly Water heavily soiled Clean pumpImpeller unit is blockedRemove blockage, check impeller unit forease of movementPump has run dry Check/clean the supply linesWater temperature too highAdhere to the maximum permissible water temperature. (→ Technical data)Technical dataAquarius Universal Classic1000 / 12 V2000 / 12 V Connection voltage V AC 1212Power consump- tion Pump W 1525 Pump and transfor- merW 2432Max. pump capacity I/h 10002000 Max. pump head m 1.52 Protection type IP68IP68 Max. immersion depth m 11Inlet portThread G 1/2G 1/2Connection, hose mm 13, 19, 2513, 19, 25 Outlet portThread G 1/2G 1/2Connection, hose mm 13, 19, 2513, 19, 25 Filter supply surface area cm2 7575 Water temperature (submerged install.)°C +4 … +35+4 … +35Ambient tempera- tur e (dry installa- tion)During operation and convection°C +4 … +30+4 … +30During operation and forced cooling°C +4 … +40+4 … +40Dimensions Length mm 125125 Width mm 8080 Height mm 7575Connection cable length m 1010 Weight kg 1.4 1.4TransformerDo not dispose of this unit with household waste.Dispose of the unit by using the return system provided for this purpose.Should you have questions, please contact your local disposal company. They will give you information on howRender the unit unusable by cutting the cables.OASE GmbHTecklenburger Straße 16148477 Hörstel | Germany+49 (0) 5454 80-0+49 (0) 5454 80-9353*************Documents / Resourcesoase 1000 Aquarius Universal Classic [pdf] User Manual1000 Aquarius Universal Classic, 1000, Aquarius Universal Classic, Universal Classic, Classic Manuals+,。
生工试剂
产品编号产品名称产品包装产品单价AE232-100G缓冲液100G441AE232-25G缓冲液25G117AE232-5KG ADA BUFFER5KGAE319-100ML PAGE电泳玻璃板硅化处理试剂100ML375AE319-12PK PAGE电泳玻璃板硅化处理试剂12PK426AE429-10MG抑肽酶10MG625AE434-100G琼脂糖100G1549AE434-1KG AgaroseⅣ1KGAE434-25G琼脂糖25G426AE434-5G琼脂糖5G98AE437-100MG两性霉素B100MG AE437-1G两性霉素B1GAE477-20ML氨苄青霉素钠20ML325AE531-0.5ML牛血清白蛋白标准溶液0.5ML229AE531-1.0ML牛血清白蛋白标准溶液 1.0ML380AE531-1.5ML牛血清白蛋白标准溶液·475AE566-1L ALKALINE TRANSFER SOLUTION AE566-250ML ALKALINE TRANSFER SOLUTION AE776-100G琼脂糖100G1142AE776-1KG Agarose3:01HRBAE776-25G琼脂糖25G343AE776-5G琼脂糖5G82AJ234-100G琼脂糖100G3015AJ234-25G琼脂糖25G829AJ234-2KG Agarose SFR2KGAJ234-5G琼脂糖5G198AJ365-100ML ABTS100ML389AJ468-100U琼脂糖酶-取消AJ581-5MG抗蛋白酶5MG472AJ582-50MG AEBSF50MG555AJ608-5MG放线菌素D5MG958AJ637-100G琼脂100G216AJ637-500G琼脂500G981AJ637-50KG AGAR50KG0ALS001041肌动蛋白-停产1MG468ALS001069乙醇脱氢酶-停止100MG601ALS001130醛缩酶100MG935ALS002763L-氨基酸氧化酶2MG695ALS002764L-氨基酸氧化酶5MG1456 ALS009043腺苷脱氨酶250U735AN0239A磷酸氢二铵500G26AN3795-100G对氨基笨磺酸100G24AN4306-100G对氨基酚100G78AN4306-2KG对氨基酚-CP2KG0AN4306-50G对氨基酚-CP50G0AN4307-100G邻氨基酚100G92AN4307-25G邻氨基酚-CP25G0AN4307-2KG邻氨基酚-CP2KG0AN5254-100G营养琼脂100G65AN5255-250G琼脂粉250G72AN5255-25KG琼脂粉25KG0AS0017-250G琼脂糖250G498AS0017-50G琼脂糖50G110AS1033-100G丙烯酰胺-5折优惠AT011高压灭菌指示带，2.5CM×55M卷98AT012高压灭菌指示带，1.8CM×50M卷78AT0173-500ML冰乙酸500ML49AT0216A氢氧化铵500ML24AT0216G氢氧化铵500ML35AT0785-500ML乙酸36%500ML32AT0850-500G氯化铵500G48AT0851-25KG硫酸铵-GR-5折优惠AT0851-500G硫酸铵-5折优惠AT0853-500G乙酸铵500G24AT0855-20KG草酸铵-GR20KG0AT0855-500G草酸铵500G34AT0856-500G碳酸铵500G26AT0857-500G过硫酸铵500G34AT0860-20KG磷酸二氢铵-GR20KG0AT0860-500G磷酸二氢铵500G34AT0861-20KG磷酸氢二铵-GR20KG0AT0861-500G磷酸氢二铵500G34AT0862-500G柠檬酸铵500G54AT0941-25G茜素绿25G98AT0941-500G茜素绿-BS500G0AT0949-25G茜素红25G19AT0957-25G苋菜红25G37AT0960-25G酸性品红25G26AT0971-25G茜素黄R25G17AT0972-25G茜素黄GG25G17AT0987-10G氨基黑10B10G28AT1014-25G L-抗坏血酸25G12AT1014-500G L-抗坏血酸-AR500G0AT1021-25G邻氨基苯甲酸25G32AT1021-500G邻氨基苯甲酸-AR500G0AT1022-25G对氨基苯甲酸25G32AT1024-25G1-氨基-2-萘酚-4-磺酸25G22AT1025-1G偶氮胂I1G62AT1026-1G偶氮胂III1G56AT1070-25G安替吡啉25G18AT1071-25G氨基比林25G19AT1074-25G4-氨基安替吡啉25G28AT1074-500G4-氨基安替吡啉-AR500G0AT1351-500G结晶氯化铝500G34AT1354-500G硝酸铝500G27AT1357-500G氢氧化铝500G26AT1358-500G中性氧化铝500G39AT1359-500G碱性氧化铝500G39AT1360-100G酸性氧化铝-AR100G0AT1360-500G酸性氧化铝500G39AT1569-20KG氯化铵-AR20KG0AT1569-500G氯化铵500G32AT1570-250G氟化铵-AR250G0AT1570-500G氟化铵500G28AT1574-500G乙酸铵500G26AT1575-10KG草酸铵-AR10KG0AT1575-500G草酸铵500G32AT1578-500G磷酸铵500G26AT1583-100G偏钒酸铵100G38AT1587-10KG碳酸氢铵-AR10KG0AT1587-500G碳酸氢铵500G22AT1595-500G磷酸二氢铵500G26AT1597-500G柠檬酸铁铵500G44AT1600-10KG柠檬酸铵-AR10KG0AT1601-500G柠檬酸铵500G38AT1603-500G500G0AT1620-500ML苯胺500ML29AT1634-100G盐酸苯胺100G54AT1706-500ML乙酸36%500ML19AT1876-100G2-氨基噻唑100G27AT1876-2KG2-氨基噻唑-AR2KG0AT1921-500ML40%乙醛500ML34AT2076-5G丙氨酸5G20AX174-100G琼脂糖100G1816AX174-1KG AgaroseⅢ1KGAX174-250G AgaroseⅢ250GAX174-25G琼脂糖25G499AX174-5G琼脂糖5G110B0010-0.1OD M13／pUC Sequencing B0011-0.1OD M13／pUC Sequencing B0011-1.0OD M13／pUC Sequencing B0012-0.1OD M13／pUC Sequencing B0012-1.0OD M13／pUC Sequencing B0013-0.1OD M13／pUC ReverseB0013-1.0OD M13／pUC ReverseB0081-1000U钻石Taq酶1000UB0081-200U钻石Taq酶200UB0089-1000U Taq酶-B0089-200U Taq酶-B0089-5000U Taq酶-B0090-100U Taq Plus100UB0090-200U Taq Plus200UB0090-500U Taq Plus500UB0093-100U Pfu DNA Polymerase B0093-200U Pfu DNA Polymerase B0093-500U Pfu DNA Polymerase B0095-100U Heatstart Taq DNAB0095-200U Heatstart Taq DNAB0095-500U Heatstart Taq DNAB01BUFFER5*1ML152B0147Cohesive-end adaptor0.5B0148Duplex0.5ODB0172-100G双丙烯酰胺100G349B0172-10KG BIS-ACRYLAMIDE10KG0B0172-25G双丙烯酰胺25G96B19Diluent Buffer SetB22Buffer for Eco52I+B2292-6福尔马林4L284B23Buffer for SduI+B24Buffer for ScaI+B25Buffer for Eam1105I+ B26Buffer for Ecl136II+ B27Buffer for Bpu10I+B28Buffer for TaqI+B29Buffer for KpnI+B30Buffer5*1ML152B57Buffer for BamHI+BB0025-100G双丙烯酰胺-5折优惠BB0025-25G双丙烯酰胺-5折优惠BB0025-25KG BIS-ACRYLAMIDE-5折优惠BB0044-1KG硼酸-5折优惠BB0072-100MG5-溴-4-氯-3-吲哚基磷酸酯钠100MG144BB0072-500MG5-溴-4-氯-3-吲哚基磷酸酯钠500MG664BB0078-500MG D-生物素500MG204BB0078-5G D-生物素5G1298BB0079-100G BIS-TRIS-7折优惠BB0079-500G BIS-TRIS-7折优惠BB0083-100G X-Gal-5折优惠BB0083-1G X-Gal-5折优惠BB0083-500MG X-Gal-5折优惠BB0085-100MG X-GLUC100MG1078BB0085-5G X-GLUC5G0BB0114-100G牛肉浸膏100G280BB0114-15KG牛肉浸膏15KG0BB0114-500G牛肉浸膏500G1190BB0260-1G BCA1G304BB0260-25G BCA25G0BB0260-5G BCA-没有折扣BB0266-100G N，N-二-羟乙基甘氨酸-7折优惠BB0266-25G N，N-二-羟乙基甘氨酸-7折优惠BB0443-25G溴百里酚蓝25G698BB0443-5G溴百里酚蓝5G171BB0637-1KG聚环氧依稀月桂酰醚1KG287BB0637-250G聚环氧依稀月桂酰醚250G88BB1111-1G碱性品红1G62BB1111-25G碱性品红25G1048BB1111-5G碱性品红5G0BB1147-100G苯甲酸100G52BB1147-1KG苯甲酸1KG448BB1160-100ML BCIP×NBT100ML398BB1160-1L BCIP×NBT1L0BB1160-25ML BCIP×NBT25ML109BB1168-100MG X-GLUC-NA100MG962BB1168-20MG X-GLUC-NA20MG245BB1170-100ML BCIP×INT100ML554BB1170-25ML BCIP×INT25ML166BB1171-100MG5-溴-4-氯-3-吲哚基磷酸酯钠100MG158BB1171-1G5-溴-4-氯-3-吲哚基磷酸酯钠1G1173BB1171-500MG5-溴-4-氯-3-吲哚基磷酸酯钠500MG655BB1171-5G BCIP-Na25G0BB1182-1G BLUO-GAL1G1822BB1182-500MG BLUO-GAL500MG998BB2230-100G溴酚蓝100G996BB2230-25G溴酚蓝25G278BB2230-5G溴酚蓝5G76BB5BUFFER B+5MLBD02-0.05MG T7DNA Phage BD02-0.25MG T7DNA Phage BD03-0.05MG pBR322DNA0.05MG BD03-0.25MG pBR322DNA0.25MG BD10-0.05MG LambdaDNA(dam,dcm)0.05MG90BD10-0.25MG LambdaDNA(dam,dcm)0.25MG360BD11-0.05MG Lambd DNA0.05MG BD11-0.25MG Lambda DNA0.25MG BE116-100ML BCIP×NBT100ML357BE116-25ML BCIP×NBT25ML98BE410-25G碱性品红-7折优惠BE410-5G碱性品红-7折优惠BE530-100ML BRADFORD REAGENT100ML BE530-1L BRADFORD REAGENT1LBE535-1KIT BRADFORD METHOD1KITBE671-1L BIO-BLOCK IN PBSBE692-100ML BCIP×INT100ML479BE692-25ML BCIP×INT25ML132BE952-500KU杆菌肽500KU492BG5BUFFER G+5MLBJ472-1G BIG CHAP1GBJ472-250MG BIG CHAP250MGBJ472-5G BOG CHAP5GBJ579-10MG贝他定10MG1379BK186-100G盐酸甜菜碱100G78BK186-1KG Betaine hydrochloride1KGBK186-500G盐酸甜菜碱500G324100MLBK217-100ML BLUE-BANDIT蛋白质电冰染色液BK217-1L BLUE-BANDIT PROTEIN STAIN500MLBK217-500ML BLUE-BANDIT蛋白质电冰染色液BM101Diamond TM250bpBM102Diamond TM250bpBM201-100μL Protein Marker，Low RangeBM201-30μL Protein Marker，Low RangeBM225-100G BES100G720BM225-25G BES25G198BM225-500G BES500G0BM523Protein Marker，Mid Range，ready BM524Protein Marker，Mid RangeBM525Pre-stained Protein Marker，Mid BN3002A硼砂500G40BN5216-1G6-苄氨基嘌呤1G40BN5216-5G6-苄氨基嘌呤5G188BN5244-100G牛肉浸膏100G49BN5244-20KG BEEF EXTRACT20KGBN5244-500G牛肉浸膏500G225BN5245-500G酵母浸膏500G64BO5BUFFER O+5MLBP10移液器，0.5-10μL支880BP100移液器，10-100μL支880BP1000移液器，100-1000μL支880BP2移液器，0.1-2.5μL支880BP20移液器，2-20μL支880BP200移液器，20-200μL支880BP50移液器，5-50μL支880BP5000移液器，1000-5000μL支880BS243双链DNA补平和连接试剂盒10次460BS244双链DNA补平和连接试剂盒20次820BS249MMLV First StrandBS250MMLV First StrandBS251AMV First StrandBS252AMV First StrandBS293Ready-to-Use PCR KitBS294Ready-to-Use PCR KitBS295HiFi Ready-to-Use PCRBS296HiFi Ready-to-Use PCRBS297Genepha Long PCRBS298Genepha Long PCRBS353UNIQ-10柱式DNA胶回收试剂盒50次300BS354UNIQ-10柱式DNA胶回收试剂盒100次500BS363UNIQ-10柱式PCR产物纯化试剂盒50次290BS364UNIQ-10柱式PCR产物纯化试剂盒100次480BS382PROTEASE INHIBITOR COCKTAIL BS387PROTEASE INHIBITOR COCKTAIL BS409Trizol25ML190BS410Trizol100ML720BS413UNIQ-10柱式质粒小量抽提试剂盒50次310BS414UNIQ-10柱式质粒小量抽提试剂盒100次53050次410BS423UNIQ-10柱式细菌基因组DNA抽提试BS424UNIQ-10柱式细菌基因组DNA抽提试100次760BS433pUCm-T Vector1μGBS434pUCm-T Vector5μGBS435PCR产物克隆试剂盒20次320BS436PCR产物克隆试剂盒100次129010次500BS463UNIQ-200柱式质粒中量抽提试剂盒BS464UNIQ-200柱式质粒中量抽提试剂盒20次80010次1000BS465UNIQ-500柱式质粒小量抽提试剂盒20次1800BS466UNIQ-500柱式质粒小量抽提试剂盒BS473经典基因组DNA抽提试剂盒50次350BS474经典基因组DNA抽提试剂盒100次42050次350BS483EZ-10柱式血液基因组DNA抽提试剂100次680BS484EZ-10柱式血液基因组DNA抽提试剂BS503Quik LB AgarBS511快速连接试剂盒20次140BS512快速连接试剂盒100次560BS513平端DNA片段添A试剂盒40次330BS514平端DNA片段添A试剂盒100次760BS523一步法制备感受态细胞溶液25ML200BS524一步法制备感受态细胞溶液50ML350BS525高效感受态细胞制备试剂盒50ML160BS526高效感受态细胞制备试剂盒100ML290BS573经典总RNA抽提试剂盒20次280BS574经典总RNA抽提试剂盒100次1080BS583UNIQ-10RNA抽提BS584UNlQ-10柱式总RNA抽提试剂盒100次1120BS589MAMMALIAN PROTEIN EXTRACTION BS596BACTERIAL PROTEIN EXTRACTION BS633UNlQ-10柱式mRNA抽提纯化试剂盒10次800BS634UNlQ-10柱式mRNA抽提纯化试剂盒20次1270BS653MMLV Single StepBS654MMLV Single StepBS663AMV Single StepBS664AMV Single StepBS686INCLUSION BODY PROTEINBS689-A IMMUNOPRECIPITATION KIT50次BS694Components sold separately BS721-20ML两性霉素B溶液-5折优惠BS722-20ML氨苄青霉素钠溶液-5折优惠BS723-5ML G418SULFATEBS724-20ML硫酸庆大霉素，R-射线灭菌-5折优惠BS725-20ML HYGROMYCIN B-BS725-2ML R-射线灭菌-5折优惠BS726-210ML硫酸卡那霉素-5折优惠BS727-20ML硫酸新霉素溶液（射线灭菌）-5折优惠BS728-20ML制霉菌素溶液（R-射线灭菌）-5折优惠BS729-2*10ML青霉素G溶液-5折优惠BS730-2*10ML硫酸链霉素溶液（R-射线灭菌）-5折优惠BS731-2*10ML盐酸四环素溶液-5折优惠BS732-2*10ML青霉素／链霉素-5折优惠BS733-2*10ML青霉素／链霉素／两性霉素B-5折优惠BS734-2*10ML青霉素／链霉素／新霉素-5折优惠BS801Quik LB AmpBS802Quik LB AgarBS803Quik LB AgarBS804Quik LB KanBS805Quik LB AgarBS806Quik LB AgarBS858HYLB-Capsule20capsulesBS859-100LB Broth-Capsule100BS859-20LB Broth-Capsule20BS860-100LB Agar-Capsule100BS860-20LB Agar-Capsule20BS861-20LB#NAME?Agar-Capsule BS862-20LB Lennox-Capsule20BS863-20LB Lennox Agar-Capsule BS864-20SOB Broth-Capsule20BS865-20SOB Agar-Capsule20BS866-20SOC Broth-Capsule20BS867-20NZCYM Broth-Capsule20BS868-20NZCYM Agar-capsule20BS869-20NZYM-Capsule20capsulesBS870-20NZYM Agar-Capsule20BS871-20NZM Broth-capsule20BS872-20NZM Agar-Capsule20BS873-20YT-Capsule20capsulesBS874-20YT Agar-Capsule20BS875-20YT-Top Agar-Capsule20BS876-202×YT-Capsule20capsulesBS877-202×YT Agar-Capsule20BS878-202×YT Top Agar-Capsule BS879-20YPD Broth-Capsule20BS880-20YPD Agar-Capsule20BS881-20M9Broth-Capsule20BS882-20M9CA Broth-Capsule20BS883-20Super Broth-Capsule20BS884-20Super Broth Agar-Capsule BS885-20Super Broth TopBS886-20Lambda Broth-Capsule20BS887-20Tryptone Broth-Capsule20BS888-20YM#NAME?20BS889-20TYGPN-Capsule20capsulesBS890-20M63Broth-Capsule20BS891-20YM Agar-Capsule20BS892-20Terrific broth-Capsule20BT0897-100KG硼酸-GR100KG0BT0897-500G硼酸500G34BT0901-250G苯甲酸250G29BT0922-1KG溴酚蓝-IND1KG0BT0922-25G溴酚蓝25G28BT0943-5G溴甲酚绿5G24BT0944-10G溴甲酚绿钠盐10G38BT0944-250G溴甲酚绿钠盐-AR250G0BT0956-5G溴酚红5G26BT0959-25G碱性品红25G19BT0962-25G曙红Y，醇溶25G39BT0963-25G曙红Y，水溶25G39BT0968-10G溴甲酚紫10G42BT0981-25G备士麦棕Y25G22BT0990-25G巴比妥钠25G70BT1018-1G吲哚-3-乙酸1G16BT1019-1G吲哚-3-丁酸1G16BT1127-25G煌橙25G32BT1128-25G苄橙25G32BT1135-1KG巴比妥酸-AR1KG0BT1135-25G巴比妥酸25G21BT1497-500G氯化钡500G27BT1500-500G硫酸钡500G26BT1501-500G硝酸钡500G24BT1502-500G乙酸钡500G43BT1504-500G氢氧化钡500G26BT1679-500G硼酸-5折优惠BT1695-250G苯甲酸250G19BT1735-250G反丁烯二酸-AR250G0BT1735-500G反丁烯二酸500G29BT1737-100G焦性没食子酸100G48BT1743-250G苯甲醇250G37BT1743-5KG苯甲醇-AR5KG0BT1972-500G双酚A500G30BT1972-5KG双酚A-AR5KG0BT2062-25G牛黄酸25G22C0101-1KG柠檬酸钠二水1KGC0101-500G柠檬酸钠二水500G50KGC0101-50KG SODIUM CITRATE，TRISODC0102-10G二甲基胂酸10G131C0102-250G二甲基胂酸250G2683C0102-50G二甲基胂酸50G590C0164-1G胰凝乳蛋白酶1G838C0164-250MG胰凝乳蛋白酶250MG252C0164-5G胰凝乳蛋白酶5G3810C0179-100G碳酸钙无水100GC0179-1KG碳酸钙无水1KG20KGC0179-20KG CALCIUM CARBONATE，ANHYC0179-500G碳酸钙无水500GC0182-10G胞嘧啶核苷10G280C0182-2G胞嘧啶核苷2G67C0182-50G胞嘧啶核苷50G1168C0196-10G二甲基胂酸钠盐三水10GC0196-250G二甲基胂酸钠盐三水250GC0196-50G二甲基胂酸钠盐三水50GC0206-100G L-半胱氨酸盐酸盐一水100G10KGC0206-10KG L-CYSTENINE HYDROCHLORIDE,MC0206-25G L-半胱氨酸盐酸盐一水25GC0206-500G L-半胱氨酸盐酸盐一水500GC0230-100G氯霉素100G578C0230-10G氯霉素10G70C0230-1KG CHLORAMPHENICOL1KG0C0230-25G氯霉素25G159C0258-100G十六烷基-二甲基-乙基-溴化铵100G181C0258-10KG CETYLDIMETHYLETHYL AMMONIUM BROMIDE C0258-25G十六烷基-二甲基-乙基-溴化铵25G58C0258-500G十六烷基-二甲基-乙基-溴化铵500G814C0271-1G磷酸肌酸钠盐四水1GC0271-25G磷酸肌酸钠盐四水25GC0271-5G磷酸肌酸钠盐四水5GC0279-100G磷酸氢钙二水100GC0279-10KG CALCIUM PHOSPHATE，DIBADIHYDRATE C0279-500G磷酸氢钙二水500GC0285-100G ACES100G724C0285-25G ACES25G199C0285-500G ACES500G0C0330-100G硫酸铜五水100GC0330-2.5KG CUPRIC SULFATE，PENTAH2.5KGC0330-500G硫酸铜五水500GC0365-10KG CAPS10KG0C0365-1KG3-（环已氨基）-1-丙磺酸1KG2382C0365-250G3-（环已氨基）-1-丙磺酸250G655C0365-50G3-（环已氨基）-1-丙磺酸50G168C0379-100G刚果红100G303C0379-25G刚果红25G88C0392-10KG CHES10KG0C0392-250G CHES250G1318C0392-25G CHES25G180C0398-100G4-氯-1-萘酚100G1618C0398-1KG4-CHLORO-1-NAPHTHOL1KG0C0398-25G4-氯-1-萘酚25G445C0398-5G4-氯-1-萘酚5G107C0412-1G胞嘧啶1G73C0412-25G胞嘧啶25G1327C0412-5G胞嘧啶5G305C0415-100G氯化铯100G448C0415-20KG CESIUM CHLORIDE20KGC0415-25G氯化铯25G121C0415-500G氯化铯500G1996C0433-100G胆固醇100G238C0433-1KG CHOLESTEROL1KG0C0433-25G胆固醇25G72C0433-500G胆固醇500G1021C0436-1G甲酚红1G32C0436-25G甲酚红25G482C0436-5G甲酚红5G106C0465-1G CHAPS-7折优惠C0465-25G CHAPS-7折优惠C0465-500G CHAPS-7折优惠C0465-5G CHAPS-7折优惠C0472-100G考马士亮兰R-250-C0472-1KG COOMASSIE BRILLIANT BLUEC0472-25G考马士亮兰R-250-C0472-5G考马士亮兰R-250-C0473-100G硫酸铯100G1034C0473-25G硫酸铯25G286C0473-5G硫酸铯5G75C0500-1G甲酚红钠盐1G30C0500-25G甲酚红钠盐25G477C0500-5G甲酚红钠盐5G105C0528-100G结晶紫100G303C0528-25G结晶紫25G80C0528-500G结晶紫500G1376C0529-1KG柠檬酸1KG262C0529-20KG CITRIC ACID20KGC0529-250G柠檬酸250G74C0556-1KG氯化钙二水-没有折扣1KGC0556-250G氯化钙二水250GC0556-500G氯化钙二水500G50KGC0556-50KG CALCIUM CHLORIDE，DIHYDC0611-100MG5-三磷酸胞苷三钠盐100MG675C0611-1G CYTIDINE-5-TRIPHOSPHATE，TRIS1G0C0611-50MG5-三磷酸胞苷三钠盐50MG372C0615-100G考马士亮兰G-250-C0615-2.5KG COOMASSIE BRILLIANT BLUEC0615-25G考马士亮兰G-250-C0615-5G考马士亮兰G-250-C0707-100G1-氯-2，4-二硝基苯100G258C0707-25G1-氯-2，4-二硝基苯25G77C0707-500G1-氯-2，4-二硝基苯500G1075C0758-100G氯化十六烷基吡啶100G145C0758-30KG CETYLDIMETHYLETHYL AMMONIUM BROMIDE C0758-500G氯化十六烷基吡啶500G658C0833-100G十六烷基-三甲基-溴化铵100G105C0833-1KG十六烷基-三甲基-溴化铵1KG819C0833-25KG CTAB25KG0C0833-500G十六烷基-三甲基-溴化铵500G447C0887-100G氯化铯100G359C0887-25G氯化铯25G98C0887-500G氯化铯500G1632C0887-5KG氯化铯5KG0C94271-100MG放线菌酮（环已酰亚胺）100MG299C94271-1G放线菌酮（环已酰亚胺）1G1182 CA33112DIGIT-12项功能1个36CA33210DIGIT，56项功能1个25CB0035-1KG柠檬酸钠二水-CB0035-500G柠檬酸钠二水-CB0037-100G考马士亮兰R-250-CB0037-25G考马士亮兰R-250-CB0037-5G考马士亮兰R-250-CB0038-100G考马士亮兰G-250-CB0038-25G考马士亮兰G-250-CB0038-5G考马士亮兰G-250-CB0051-100G硫酸铯100G1156 CB0051-25G硫酸铯25G351CB0051-5G硫酸铯5G95CB0052-100G碳酸钙无水100G CB0052-1KG碳酸钙无水1KGCB0052-500G碳酸钙无水500G CB0054-100G氯化铯100G413CB0054-25G氯化铯25G114CB0054-500G氯化铯500G1960 CB0055-1KG柠檬酸-7折优惠CB0055-250G柠檬酸-7折优惠CB0088-100G L-胱氨酸100G68CB0088-1KG L-CYSTINE1KG0CB0088-500G L-胱氨酸500G252CB0097-250G3-（环已氨基）-1-丙磺酸-7折优惠CB0097-50G3-（环已氨基）-1-丙磺酸-7折优惠CB0105-100G十六烷基-二甲基-乙基-溴化铵100G198CB0105-25G十六烷基-二甲基-乙基-溴化铵25G65CB0105-500G十六烷基-二架基-乙基-溴化铵500G916CB0108-100G十六烷基-三甲基-溴化铵-7折优惠CB0108-1KG十六烷基-三甲基-溴化铵-7折优惠CB0108-500G十六烷基-三甲基-溴化铵-7折优惠CB0115-250G CHES-7折优惠CB0115-25G CHES-7折优惠CB0118-100G氯霉素-5折优惠CB0118-25G氯霉素-5折优惠CB0118-25KG氯霉素-5折优惠CB0124-1G6-氯嘌呤-取消CB0124-250MG6-氯嘌呤-取消CB0124-25G6-CHLOROPURINE5G0CB0132-100G L-半胱氨酸100G134CB0132-500G L-半胱氨酸500G530CB0132-50G L-半胱氨酸50G72CB0132-5KG L-CYSTEINE5KG0CB0133-100G L-半胱氨酸盐酸盐100G256CB0133-25G L-半胱氨酸盐酸盐25G77CB0152-1G CIBACRON BRILLIANT REDCB0152-25G CIBACRON BRILLIANT REDCB0152-5G CIBACRON BRILLIANT REDCB0153-1G CIBACRON BRILLIANT YELLOW CB0153-25G CIBACRON BRILLIANT YELLOW CB0153-5G CIBACRON BRILLIANT YELLOW CB0155-1G汽巴蓝F3GA1G30CB0155-5G汽巴蓝F3GA5G106CB0201-1K KU胰凝乳蛋白酶-CB0201-250KU胰凝乳蛋白酶-取消CB0321CTP25UMOL135CB0321-1ML CTP(100mM)1ML0CB0351-100ML氯仿：异戊醇（24：1）100ML118CB0351-200ML氯仿：异戊醇（24：1）200ML192CB0351-950ML CHLOROFORM:ISOAMYL ALCOHOL(24:1)950ML CB3060-100G酪蛋氨基酸（酪蛋白水解物）-没100G60CB3060-4*500G酪蛋氨基酸（酪蛋白水解物））-4*500G950CB3060-500G酪蛋氨基酸（酪蛋白水解物））-500G250CB3060-70KG酪蛋氨基酸（酪蛋白水解物）70KG0CB4211-1G天青石蓝1G75CB4211-5G天青石蓝5G312CB5277-1G头孢菌素C锌盐1G71 CB5277-25G头孢菌素C锌盐25G1463 CB5277-5G头孢菌素C锌盐5G322 CE203-5ML即用型细菌细胞裂解液5ML745 CE302-1G CHAPSO1G370 CE302-50G CHAPSO50G0CE302-5G CHAPSO5G1609 CE506-100ML1M氯化钙溶液100ML CE506-500ML1M氯化钙溶液500ML CLS001260碳酸酐酶50MG321 CLS001263碳酸酐酶250MG1069 CLS001333胰凝乳蛋白酶1G227 CLS001334胰凝乳蛋白酶10G1604 CLS001430胰凝乳蛋白酶25MG241 CLS001432胰凝乳蛋白酶100MG755 CLS001448胰凝乳蛋白酶250MG334 CLS001641CLOSTRIPAIN1MG0 CLS001652胶原（蛋白）5G468 CLS001654胶原（蛋白）1G132 CLS001656胶原（蛋白）10G735 CLS001722羧肽酶B1KU401 CLS001724羧肽酶B3KU869 CLS001847过氧化氢酶2G454 CLS001849过氧化氢酶10G1871 CLS001872过氧化氢酶10ML200 CLS001873过氧化氢酶100ML935 CLS001896过氧化氢酶10ML214 CLS001898过氧化氢酶100ML1403 CLS002598纤维素酶250MG307 CLS002601纤维素酶1G762 CLS002610纤维素酶1G401 CLS002611纤维素酶10G3140 CLS003708胰蛋白酶100MG174 CLS004103胆淄醇酯酶100U401 CLS004104胆淄醇酯酶500U1510 CLS004174胶原酶2型100MG321 CLS004177胶原酶2型5G0 CLS004180胶原酶3型100MG321 CLS004182胶原酶3型1G1871 CLS004183COLLAGENASE，TYPE35G0 CLS004186胶原酶4型100MG321 CLS004188胶原酶4型1G1871 CLS004189COLLAGENASE,TYPE45G0 CLS004194胶原酶1型100MG321 CLS004196胶原酶1型1G1871 CLS004197COLLAGENASE，TYPE15G0 CLS004202胶原酶2型50MG374CLS004204胶原酶2型250MG1443 CLS004206胶原酶3型50MG374 CLS004208胶原酶3型250MG1443 CLS004210胶原酶4型50MG374 CLS004212胶原酶4型250MG1443 CLS004214胶原酶1型50MG374 CLS005273胶原酶10KU1804 CLS005301羧肽酶B10MG962 CLS005304羧肽酶B50MG4276 CLS005305羧肽酶B5MG641 CLS005623CHYMOTRYPSINOGEN A，PURIFIED5G CLS005630胰凝乳蛋白酶原1G481 CLS005632胰凝乳蛋白酶原5G1737 CLS009068羧肽酶Y5MG3341 CLS009070羧肽酶Y1MG802 CLT001弹簧水夹，不锈钢，40MM4个15 CLT002弹簧水夹,不锈钢,60MM4个17 CLT003弹簧水夹,弹力钢,80MM4个20 CLV001铜,260MM,爪式万能夹1个23 CN0721-500G磷酸氢钙500G74 CN0721C磷酸氢钙500G74 CN1138-1KG卡那胶1KG350 CN1138-20KG卡那胶20KG0 CN1138-500G卡那胶500G180 CN3924A-250G水合氯醛250G42 CN5204-500G干酪素500G98 CT0123-500ML氯仿（三氯甲烷）500ML60 CT0124-4L氯仿（三氯甲烷）4L398 CT0124-500ML氯仿（三氯甲烷）-HPLC500ML0 CT0914-10G邻甲酚酞10G20 CT0928-100G克罗拉卓蓝100G35 CT0933-5G考马士亮兰G-2505G CT0934-10G考马士亮兰R-250-BS10G CT0934-500G考马士亮兰R-250-BS500G CT0934-5G考马士亮兰R-2505G CT0953-25G甲酚红25G26 CT0953-500G甲酚红-AR500G0 CT0954-250G刚果红-IND250G0 CT0954-25G刚果红25G28 CT0966-25G结晶紫25G16 CT0966-500G结晶紫-AR500G0 CT0969-10G间甲酚紫10G34 CT0969-200G间甲酚紫-AR200G0 CT0970-5G邻苯耳酚紫5G26 CT0975-100G香豆素100G48 CT0976-5G姜黄素5G44 CT0978-5G钙黄绿素5G20CT0985-25G铬黑T25G22 CT0986-250G依来铬蓝黑R-IND250G0 CT0986-25G依来铬蓝黑R25G19 CT1004-250G变色酸-AR250G0 CT1004-25G变色酸25G34 CT1027-10G偶氮氯膦I-AR10G CT1027-1G偶氮氯膦I1G CT1028-1G偶氮氯膦III1G CT1059-25G邻甲酚酞络合指示剂25G78 CT1105-25G辛可宁25G238 CT1110-10G铬天青S10G29 CT1112-25G D-泛酸钙25G26 CT1114-100G氯化胆碱100G34 CT1136-250G黄七精Y-IND250G0 CT1136-25G黄七精Y25G118 CT1143-10G盐基淡黄10G32 CT1314-250G碳酸钙250G25 CT1315-500G硝酸钙500G26 CT1317-500G乙酸钙500G29 CT1318-500G草酸钙500G34 CT1321-500G氧化钙500G0 CT1322-500G氟化钙500G29 CT1325-250G氢氧化钙-AR250G0 CT1325-500G氢氧化钙500G22 CT1326-25KG柠檬酸钙-AR25KG0 CT1326-500G柠檬酸钙500G32 CT1330-500G无水氯化钙500G26 CT1331-500G氯化钙二水500G CT1425-500G硫酸铜五水500G CT1426-10KG硝酸铜-AR10KG0 CT1427-500G乙酸铜500G64 CT1429-10KG氯化铜-AR10KG0 CT1429-500G氯化铜500G48 CT1434-10KG氢氧化铜-AR10KG0 CT1434-250G氢氧化铜-AR250G0 CT1434-500G氢氧化铜500G57 CT1439-100G酒石酸铜100G52 CT1444-500G无水硫酸铜500G39 CT1459-100G硫酸钴100G0 CT1460-100G硝酸钴100G34 CT1460-2KG硝酸钴-AR2KG0 CT1461-100G乙酸钴100G38 CT1463-100G草酸钴100G59 CT1464-100G氯化钴100G29 CT1464-5KG氯化钴-AR5KG0 CT1482-500G硝酸铬500G52 CT1484-500G氧化铬500G64CT1485-500G氯化铬500G0CT1490-250G氧化镉250G0CT1491-250G氯化镉250G49CT1492-100G乙酸镉100G47CT1493-100G硫酸镉100G0CT1495-250G硝酸镉250G68CT1542-1KG活性碳粉状1KGCT1542-500G活性碳粉状-AR500GCT1543-1KG活性碳柱状1KGCT1544-1KG活性碳颗粒状1KGCT1544-500G活性碳颗粒状-AR500G(用于1KG) CT1611-100G十六烷基-三甲基-溴化铵-5折优惠CT1614-25G十六烷基-三甲基-氯化铵25G46CT1702-500G柠檬酸-5折优惠CT1705-500G氯乙酸500G28CT1707-500ML正辛酸500ML44CT1859-500ML蓖麻油500ML32CT1860-25ML香柏油25ML14CT2004-500ML氯仿（三氯甲烷）500ML28CT2041-100G肌酐-BR100G0CT2041-5G肌酐5G98CT2042-25G肌醇25G14CT2042-500G肌醇-BR500G0CT2042-5KG肌醇-BR5KG0CT2056-25G肌酸25G19CT2057-25G胆酸25G72CT2121-500G环糊精500G39CT2149-100G乳酸钙100G22CT2149-5KG乳酸钙-BR5KG0CT2154-25G泛酸钙25G24CT2154-500G泛酸钙-BR500G0D0044-1DATP-低于5折优惠D0046-1DCTP-低于5折优惠D0048-1DGTP-低于5折优惠D0050-1DTTP-低于5折优惠D0055DNTP-低于5折优惠D0056dNTP-低于5折优惠D0081-1000U Tsg DNA PolymeraseD0081-200U Tsg DNA PolymeraseD0081-5000U Tsg DNA PolymeraseD0198-10G硫酸葡聚糖10G146D0198-10KG DEXTRAN SULFATE10KGD0198-250G硫酸葡聚糖250G2438D0231-100ML二甲亚砜100ML49D0231-20L DMSO20L0D0231-500ML二甲亚砜500ML188D0238-1KG二乙醇胺1KG229D0238-2.5KG DIETHANOLAMINE 2.5KG0D0238-250G二乙醇胺250G65D0238-500G DIETHANOLAMINE(用于1KG)500G0D0293-250ML二乙胺250ML93D0293-950ML二乙胺950ML322 D0425-1G二硫赤藓糖醇1G81D0425-25G DTE25G0D0425-5G二硫赤藓糖醇5G349 D0430-100G DAB，TETRAHYDROCHLORIDE100G0D0430-1G3，3二氨基联苯胺四盐酸二水D0430-25G3，3二氨基联苯胺四盐酸二水D0430-5G3，3二氨基联笨胺四盐酸二水D0435-10G DANSYL CHLORIDE10G D0435-1G丹磺酰氯1G207 D0435-5G丹磺酰氯5G928 D0445-10G DEAE葡聚糖10G109 D0445-250G DEAE DEXTRAN250G D0445-50G DEAE葡聚糖50G480 D0456-100G2’-DEOXYADENOSINE，MONOHYDRA100G0D0456-1G2’-脱氧腺苷一水1GD0456-5G2’-脱氧腺苷一水5GD0464-20L N’，N-DIMETHYLFORMAMIDE20L0D0464-250ML N’，N-二甲基甲酰胺250ML73D0464-500ML N’，N-二甲基甲酰胺500ML113 D0467-100G2’-DEOXYCYTIDINE，HYDROCHLOR100G0D0467-1G2’-脱氧胞苷盐酸盐1G272 D0467-5G2’-脱氧胞苷盐酸盐5G1235 D0475-100G2-DEOXYGUANOSINE，MONOHYDRATE100G0D0475-100MG2’-脱氧鸟苷一水100MG D0475-1G2’-脱氧鸟苷一水1GD0475-500MG2’-脱氧鸟苷一水500MG D0481-1G2’-脱氧胸苷1G81D0481-25G2’-脱氧胸苷25G1666 D0481-5G2’-脱氧胸苷5G367 D0491-1G2’-脱氧尿苷1G583 D0491-250MG2’-脱氧尿苷250MG169 D0491-5G2’-脱氧尿苷5G2650 D0503-100MG5’-三磷酸-2’-脱氧腺苷二钠盐100MG1832 D0503-50MG5’-三磷酸-2’-脱氧腺苷二钠盐50MG941 D0518-100MG5’-三磷酸-2’-脱氧胞苷三钠盐100MG1390 D0518-50MG5’-三磷酸-2’-脱氧胞苷三钠盐50MG763 D0526-250MG5’-三磷酸-2’-脱氧鸟苷三钠盐250MG4000 D0526-50MG5’-三磷酸-2’-脱氧鸟苷三钠盐50MG881 D0532-100MG5’-三磷酸-2’-脱氧胸苷三钠盐100MG1994 D0532-50MG5’-三磷酸-2’-脱氧胸苷三钠盐50MG1200 D0613-10G脱氧胆酸钠盐10G67D0613-250G脱氧胆酸钠盐250G1391D0613-500G DEOXYCHOLIC ACID SODIUM D0613-50G脱氧胆酸钠盐50G306D0624-100ML十二烷基-三甲基-氯化铵100ML256D0624-25ML十二烷基-三甲基-氯化铵25ML85D0624-500ML十二烷基-三甲基-氯化铵500ML1096 D0644-100G DNA100G0D0644-1G DNA1G68D0644-25G DNA25G1290 D0644-500G DNA500G0D0644-5G DNA5G284D0649-100KU脱氧核糖核酸酶I100KU D0649-50KU脱氧核糖核酸酶I50KU D0657-1G2’-脱氧-D-核糖1G126D0657-50G2-DEOXY-D-RIBOSE50G0D0657-5G2’-脱氧-D-核糖5G572D0665-100G葡聚糖100G858D0665-1KG DEXTRAN1KG0D0665-25G葡聚糖25G236D0665-5G葡聚糖5G59DT0119-500ML二氯甲烷500ML65DT0120-4L二氯甲烷4L430 DT0120-500ML二氯甲烷-HPLC500ML0DT0151-500ML N，N-二甲基甲酰胺500ML69DT0152-4L N，N-二甲基甲酰胺4L592 DT0153-4L N，N-二甲基甲酰胺-HPLC4L0DT0153-500ML N，N-二甲基乙酰胺500ML84DT0163-500ML二甲亚砜500ML118 DT0164-4L二甲亚砜4L788 DT0746-500ML二氯甲烷500ML32DT0777-500ML N，N-二甲基甲酰胺500ML42DT0778-500ML N，N-二甲基乙酰胺500ML39DT0913-25G酚酞25G12DT0913-2KG酚酞-IND2KG0DT0973-25G二甲基黄25G38DT0994-25G变色酸钠25G42DT0997-25G二苯胺磺酸钠25G20DT1043-5G双硫腙（铅试剂）5G18DT1079-25G二苯偶氮碳酰肼25G38DT1100-250G对苯二酚250G37DT1101-100G间苯二酚100G26DT1102-100G邻苯二酚100G156 DT1321氯化钙干燥管，单球5个20DT1322氯化钙干燥管，双球5个20DT1568-500G硅藻土500G22DT1609-25G十二烷基-三甲基-溴化铵25G26DT1609-500G十二烷基-三甲基-溴化铵-AR500G0DT1612-100G十二烷基-三甲基-氯化铵-AR100G0DT1612-25G十二烷基-三甲基-氯化铵25G26DT1621-100G二苯胺100G19DT1621-2KG二苯胺-AR2KG0DT1635-100G对苯二胺100G32DT1635-25G对苯二胺25G0DT1636-100G邻苯二胺100G32DT1637-100G间苯二胺100G32DT1644-500ML二乙醇胺500ML29DT1664-500ML N，N-二甲基甲酰胺500ML34DT1665-500ML N，N-二甲基乙酰胺500ML32DT1697-500G月桂酸500G29DT1729-500G D-酒石酸500G104DT1731-100G DL-苹果酸-BR100G0DT1731-500G DL-苹果酸500G38DT1899-500G糊精500G29DT1976-100G2，4-二硝基苯酚100G44DT1977-100G二硝基苯酚100G64DT2003-500ML二氯甲烷500ML24DT2043-10G甜醇10G78DT2047-25G盐酸吡哆醇25G24DT5551-100G邻二氯苯酚100G97DTC003组织培养皿，12／包10*包26DTC007组织培养皿，10／包10包28DTC009组织培养皿，10／包10包35DTC015组织培养皿，单独包装包19E0105-100G乙二胺四乙酸二钠盐二水100GE0105-1KG乙二胺四乙酸二钠盐二水1KGE0105-500G乙二胺四乙酸二钠盐二水500GE0105-50KG EDTA DISODIUM SALTE0109-100G曙红Y100G378E0109-25G曙红Y25G104E0109-5G曙红Y5G32E0219-10G红霉素10G265E0219-2G红霉素2G63E0219-50G红霉素50G1102E0322-100G乙二胺四乙酸100G45E0322-1KG乙二胺四乙酸1KG361E0322-500G乙二胺四乙酸500G198E0492-1G溴化乙锭-7折优惠E0492-25G溴化乙锭-7折优惠E0492-500G ETHIDIUM BROMIDE[EB]500GE0492-5G溴化乙锭-7折优惠E0582-1L乙二醇1L212E0582-250ML乙二醇250ML65E0582-4L ETHYLENE GLYCOL4LE0720-100G乙二胺四乙酸二钾盐二水100GE0720-20KG EDTA DEPOTASSIUN SALTE0720-500G乙二胺四乙酸二钾盐二水500GE0732-1KG EGTA1KG0E0732-250G EGTA250G3236E0732-50G EGTA50G690E0732-5G EGTA5G83E261Low Range IE273Wide-Range Marker200μGE279Marks-IT TM100μGE683Low Range IIE687Low Range IIIE840DNA MicroMarker TME854PCR DNA MarkerEB0075-100G二乙胺四乙酸二钾盐二水100G0EB0075-500G二乙胺四乙酸二钾盐二水500G0EB0107-100G乙二胺四乙酸-7折优惠EB0107-1KG乙二胺四乙酸-7折优惠EB0107-500G乙二胺四乙酸-7折优惠EB0185-100G乙二胺四乙酸二钠盐二水-EB0185-1KG乙二胺四乙酸二钠盐二水-EB0185-500G乙二胺四乙酸二钠盐二水-EB0192-25G红霉素25G408EB0192-5G红霉素5G98EB0195-1G溴化乙锭-7折优惠EB0195-5G溴化乙锭-7折优惠EB0577-100G EDC100G0EB0577-1G EDC1G89EB0577-25G EDC25G202EB0577-5G EDC5G425EB315-100U无机焦磷酸酶-取消EB315-500U无机焦磷酸酶-取消EB333-200U无机焦磷酸酶-取消EB333-50U无机焦磷酸酶-取消EB517-10KU MMLV Reverse Transcriptase EB517-2KU MMLV Reverse Transcriptase EE406-5ML ETHIDIUM BROMIDE[EB]5MLEE522-100ML EDTA100ML192EF0261碱性磷酸酶，150U／μL7500U899EF0341碱性磷酸酶200U187EF0342碱性磷酸酶5*200U560EJ586-5MG E-645MG936EJ844-10TABS ETHIDIUM BROMIDE[EB]10TABSEJ844-25TABS ETHIDIUM BROMIDE[EB]25TABSEJ845-10T ETHIDIUM BROMIDE[EB]10TABSEJ845-25T ETHIDIUM BROMIDE[EB]25TABSEK0031T4多聚核苷酸激酶500UEK0032T4多聚核苷酸激酶2500UEL0011T4DNA连接酶EL0012T4DNA连接酶EL0013T4DNA连接酶EL0014T4DNA连接酶EL0017T4DNA连接酶EL0021T4RNA连接酶EL0331T4DNA连接酶EL0334T4DNA连接酶EL0337T4DNA连接酶ELS002290弹性蛋白酶25MG401ELS002292弹性蛋白酶100MG1269EN0171核酸酶BAL3150UEN0181微球菌核酸酶8000U455EN0191外切核酸酶III4000UEN0201核糖核酸酶H100UEN0202核糖核酸酶H500UEN0321核酸酶S110000U EN0361尿嘧啶DNA糖基酶200U455EN0362尿嘧啶DNA糖基酶5×200U1819EN0531RIBONUCLEASE A10MGEP0041DNA聚合酶IEP0042DNA聚合酶IEP0051DNA聚合酶IEP0052DNA聚合酶IEP0061T4DNA聚合酶EP0062T4DNA聚合酶EP0081T7DNA聚合酶EP0101T3RNA聚合酶EP0102T3RNA聚合酶EP0103T3RNA聚合酶EP0111T7RNA聚合酶EP0112T7RNA聚合酶EP0113T7RNA聚合酶EP0131SP6RNA聚合酶EP0161末端脱氧核苷转移酶500U606EP0162末端脱氧核苷转移酶2500U2425EP0421DNA polymerase IEP0422DNA polymerase IEP0441M-MLV逆转录酶2×5000U EP0442M-MLV逆转录酶10×5000U ER0011Alu I600UER0021Alw21I200UER0022Alw21I1000UER0031Alw26I1000UER0032Alw26I5000UER0041Alw44I1000UER0042Alw44I5000UER0051BamH I4000UER0052BamH I20000U ER0053BamH I HC20000U ER0061Bcn I1000U ER0062Bcn I5000U ER0072Bg1I10000U ER0081Bgl II500UER0082Bgl II2500U ER0091Bpu1102I200UER0092Bpu1102I1000U ER0111Bsp68I500UER0112Bsp68I2500U ER0121Bsp1191I2500U ER0131Bsp120I1500U ER0132Bsp120I7500U ER0133Bsp120I HC7500U ER0142Bsu15I3000U ER0151BsuR I3000U ER0152BsuR I15000U ER0161Cfr I200UER0162Cfr I1000U ER0172Cfr9I1500U ER0181Cfr10I200UER0182Cfr10I1000U ER0192Cfr13I5000U ER0202Cfr42I6000U ER0211Csp6I1500U ER0221Dra I1500U ER0222Dra I75000U ER0231Eam1104I300UER0232Eam1104I1500U ER0241Eam1105I1000U ER0242Eam1105I5000U ER0251Ecl136II1500U ER0252Ecl136II7500U ER0273EcoR I HC25000U ER0281Eco24I1500U ER0291Eco31I500UER0292Eco31I2500U ER0301Eco32I2000U ER0303Eco32I HC1000U ER0311Eco47I800UER0322Eco47III1000U ER0331Eco52I500UER0332Eco52I2500U ER0342Eco57I500UER0362Eco72I10000U ER0372Eco81I2500UER0381Eco88I1000U ER0392Eco91I5000U ER0401Eco105I600UER0402Eco105I3000U ER0421Eco147I1000U ER0422Eco147I5000U ER0432Sca I5000U ER0452Esp3I1000U ER0471Hin1I300UER0472Hin1I1500U ER0482Hin6I10000U ER0491Hinc II500UER0501Hind III5000U ER0502Hind III25000U ER0503Hind III HC25000U ER0512Hpa II5000U ER0521Kpn I4000U ER0522Kpn I20000U ER0523Kpn I HC20000U ER0541Msp I3000U ER0542Msp I15000U ER0551Mva I2000U ER0552Mva I10000U ER0562Mlu I5000U ER0571Nco I500UER0572Nco I2500U ER0581Nde I500UER0582Nde I2500U ER0591Not I300UER0601Pae I500UER0602Pae I2500U ER0611Pst I3000U ER0613Pst I HC15000U ER0622Pvu I1500U ER0631Pvu II2500U ER0632Pvu II12500U ER0633Pvu II HC12500U ER0641Sal I1500U ER0642Sal I7500U ER0643Sal I HC7500U ER0651Sdu I500UER0661Sma I1200U ER0662Sma I6000U ER0663Sma I HC6000U ER0671Taq I3000U ER0672Taq I15000U ER0681Xba I1500U。
新代参数设定参考手册
新代参数设定参考手册(总87页)-CAL-FENGHAI.-(YICAI)-Company One1-CAL-本页仅作为文档封面，使用请直接删除新代科技參數設定說明手冊by : 新代科技date :2006/11/20ver : 9.5版本更新記錄目錄1.參數總表 (7)2.參數設定說明 (36)2.1 系統基本參數設定 (36)2.1.1 硬體環境設定 (36)2.1.1.1 軸卡基本參數設定 (36)2.1.1.1.1Pr01 軸板基址 (36)2.1.1.1.2Pr09 軸板型態 (37)2.1.1.1.3 Pr10 伺服警報接點型態 (37)2.1.1.1.4Pr11 軸卡時脈來源 (38)2.1.1.1.5Pr12 SERVO6 軸卡最高時脈 (38)2.1.1.1.6Pr13 軸卡數目 (38)2.1.1.2 I/O 卡基本參數設定 (39)2.1.1.2.1Pr03 I/O 板基址 (39)2.1.1.2.2Pr05 I/O 板組態 (39)2.1.1.2.3Pr15 I/O 卡數位濾波程度 (42)2.1.1.3 控制精度設定 (43)2.1.1.3.1 Pr17 控制精度 (43)2.1.1.4 螢幕功能鍵型態設定 (43)2.1.1.4.1 Pr3205 功能鍵型態 (43)2.1.1.5 螢幕型別 (44)1 Pr3211 螢幕型別 (44)2.1.1.6 預設外部存取資料磁碟機代號 (44)1 Pr3213 磁碟機代號 (44)2.1.1.7 選擇控制面板鍵盤型態 (44)1 Pr3217 選擇控制面板鍵盤型別 (44)2.1.1.8 系統掃瞄時間設定 (45)1 Pr3202 I/O 掃描時間 (45)2 Pr3203 運動補間時間 (45)3 Pr3204 PLC 掃描時間 (45)2.1.2 軟體介面環境參數設定 (46)2.1.2.1 應用功能參數設定 (46)1 Pr411 G00 運動方式 (46)2 Pr413 G92(G92.1)座標保留模式設定 (46)2.1.2.1.3 Pr414 工件座標系統保留模式 (46)4 Pr415 重置或關機時保留目前刀長資料 (47)5 Pr3207 C/S 界面版本編號 (47)6 Pr3215 選刀時呼叫副程式 (47)7 Pr3241 工件程式小數點型態 (47)8 Pr3243 鍵盤重置鍵由 PLC 處理 (48)9 Pr3245 刀長磨耗補償輸入增量最大值 (48)0 Pr3801 G95 時進給量與主軸位置緊密偶合 (48)Pr3807 圓弧終點不在圓弧上檢查視窗 (49)2.1.2.1.12 Pr3809 UVW 為 XYZ 軸增量指令 (49)2.1.2.1.13 Pr3815 刀具半徑補償預看模式 (49)2.1.2.1.14 Pr3816 刀長補償模式 (49)5 Pr3819 過切檢查型態 (50)Pr3851 斷刀處理程式號碼 (50)2.1.2.2 系統人機介面設定 (51)1 Pr3201 設定啟動車床規則 (51)2 Pr3209 語言設定 (51)3 Pr3219 系統安裝組態 (52)4 Pr3221 除錯模式 (52)5 Pr3223 啟動系統管理功能 (53)6 Pr3225 螢幕保護功能延遲時間 (53)7 Pr3227 螢幕解析度 (53)2.1.2.2.8 Pr3229 關閉工件座標系統功能 (53)9 Pr3247 速率顯示方法 (54)2.2.伺服軸向參數設定 (55)2.2.1 各軸對應機械軸設定 (55)2.2.1.1 Pr21~Pr40 伺服對應的機械軸 (55)2.2.2 軸向馬達運動方向的設定 (55)2.2.2.1 Pr41~Pr60 馬達運動方向設定 (55)2.2.3 軸向命令與回授解析度設定 (56)2.2.3.1 Pr61~Pr80 位置感測器解析度 (56)Pr81~Pr100 軸卡回授倍頻 (56)Pr121~Pr160 螺桿側齒輪齒數,馬達側齒輪齒數 (56)Pr161~Pr180 螺桿寬度(Pitch) (56)Pr181~Pr200 伺服系統的位置迴路增益 (56)Pr201~Pr220 位置感測器型態 (56)Pr341~Pr360 位置命令倍率分子 (56)Pr361~Pr380 位置命令倍率分母 (56)2.2.4 各軸向應用型態設定 (58)2.2.4.1 Pr221~Pr226 軸型態 (58)2.2.4.2 Pr281~Pr300 選擇半徑軸或直徑軸 (59)2.2.5 各軸向顯示名稱設定 (59)2.2.5.1 P r321~Pr340 設定軸的名稱 (59)2.2.6 軸向控制模式設定 (60)2.2.6.1 Pr381~Pr400 位置伺服控制模式 (60)2.2.7 定位檢查功能設定 (60)2.2.7.1 Pr421~Pr440 切削時位置檢查的視窗範圍 (60)2.2.7.2 Pr481~Pr500 快速移動(Rapid T ravel, G00)時位置檢查的視窗範圍 (61)2.2.7.3 Pr561~Pr580 遺失位置檢查視窗 (61)2.2.7.4 Pr901~Pr920 零速檢查視窗 (61)2.2.8 各軸向左右軟體行程極限保護 (61)2.2.8.1 Pr2401~Pr2440 軟體第一行程保護的範圍 (61)2.2.8.2 Pr2441~Pr2480 軟體第二行程保護的範圍 (62)2.3.主軸參數設定 (63)2.3.1 主軸對應命令輸出埠設定 (63)2.3.1.1 Pr1621~Pr1630 主軸對應的機械軸或邏輯軸 (63)2.3.2 主軸命令參數設定 (63)2.3.2.1 Pr.1631~Pr.1636 主軸零速offset 速度 (63)2.3.2.2 Pr.1641~Pr.1646 主軸編碼器極性 (63)2.3.2.3 Pr.1651~Pr.1656 主軸馬達編碼器一轉的Pulse 數 (63)2.3.2.4 Pr.1661~Pr.1666 主軸回授倍頻 (64)2.3.2.5 Pr.1671~Pr.1676 主軸馬達增益 (64)2.3.2.6 Pr.1681~Pr.1692 主軸第一檔齒數比 (64)Pr.1901~Pr.1952 主軸第四檔齒數比 (64)2.3.2.7 P r.1711~Pr.1716 主軸是否安裝編碼器 (65)2.3.3 主軸運動轉速設定參數 (65)2.3.3.1 Pr.1721~Pr.1726 主軸寸動速度 (65)2.3.3.2 Pr.1731~Pr.1736 主軸最低轉速 (65)2.3.3.3 Pr.1801~Pr.1806 主軸最高轉速 (65)2.3.3.4 Pr.1821~Pr.1826 主軸伺服微分增益 (65)2.3.3.5 Pr.1831~Pr.1836 主軸加減速時間 (66)2.3.3.6 Pr.1851~Pr.1856 主軸重力加速度加減速時間 (66)2.3.4 主軸定位設定參數 (66)2.3.4.1 Pr.1741~Pr.1746 主軸定位速度 (66)2.3.4.2 Pr.1741~Pr.1746 主軸定位偏移量 (66)2.3.4.3 Pr.1771~Pr.1776 主軸原點偏移量 (66)2.3.4.4 Pr.1781~Pr.1786 主軸定位最低速度 (67)2.3.4.5 Pr.1791~Pr.1796 主軸馬達型態 (67)2.3.4.6 P r.1811~Pr.1816 主軸編碼器安裝位置 (67)2.3.4.7 Pr.1841~Pr.1846 主軸Y-Delta 切換速度 (67)2.4.軸向運動特性設定參數 (69)2.4.1 切削時前加減速運動規劃 (69)2.4.1.1 Pr401 切削加減速時間 (69)Pr402 重力加速度加減速時間 (69)Pr405 切削的最高進給速度 (69)Pr541~Pr560 各軸切削的加減速時間 (69)Pr621~Pr640 各軸切削的最高進給速度 (69)Pr641~Pr660 各軸重力加速度加減速時間 (69)2.4.2 切削時後加減速運動規劃 (71)2.4.2.1 Pr404 後加減速切削鐘型加減速時間 (71)2.4.3 切削時直線轉角自動減速功能 (73)2.4.3.1 P r406 轉角參考速度 (73)2.4.4 切削時圓弧切削運動最高進給速度設定 (74)2.4.4.1 Pr408 半徑5mm 圓弧切削參考速度 (74)2.4.5 快速移動及 JOG 時的加減速規劃 (75)2.4.5.1 Pr441~Pr460 各軸快速移動(G00)的加減速時間 (75)Pr461~Pr480 各軸快速移動(G00)的最高進給速度 (75)Pr501~Pr520 各軸快速移動(G00)的F0 速度 (75)Pr521~Pr540 各軸JOG 速度 (75)2.5.尋原點動作設定參數 (76)2.5.1 尋原點方式設定參數 (76)2.5.1.1 Pr961~Pr980 各軸尋原點方法 (76)2.5.2 尋原點動作規格與參數設定 (76)2.5.2.1 Pr821~Pr840 各軸第一段尋原點速度 (76)Pr841~Pr860 各軸第二段尋原點速度 (76)Pr861~Pr880 各軸尋原點為負方向 (76)2.5.3 原點偏移功能設定參數 (77)2.5.3.1 Pr881~Pr900 原點的偏移量設定 (77)2.5.4 原點柵格量功能設定參數 (78)2.5.4.1 Pr941~Pr960 啟動尋原點柵格功能 (78)2.6.手輪功能設定參數 (80)2.6.1 手輪訊號輸入設定參數 (80)2.6.1.1 Pr2031~Pr2034 手輪對應的機械軸 (80)2.6.2 手輪訊號解析度設定參數 (80)2.6.2.1 Pr2041~Pr2044 手輪Encoder 一轉的Pulse 數 (80)Pr2051~Pr2054 手輪回授倍頻 (80)2.6.3 手輪段數設定參數 (80)2.6.3.1 Pr2001 手輪第四段倍率設定 (80)2.6.4 手輪模擬功能設定參數 (81)2.6.4.1 Pr2003 手輪模擬對應手輪號碼 (81)2.6.5 手輪驅動軸向功能設定參數 (81)2.6.5.1 Pr2031~Pr2033 手輪對應的座標軸 (81)2.6.5 手輪設定參數 (81)2.6.5.1 Pr2031~Pr2033 手輪對應的座標軸 (81)2.7.機構補償功能設定參數 (82)2.7.1 尖角誤差補償設定參數 (82)2.7.1.1 Pr1361~Pr1380 圓弧尖角正向誤差補償量 (82)Pr1381~Pr1400 圓弧尖角誤差補償時間常數 (82)Pr1361~Pr1400 圓弧尖角負向誤差補償量 (82)2.8.軸耦合功能設定參數 (85)2.8.1 軸耦合功能設定參數 (85)2.8.1.1 Pr1361~Pr1380 圓弧尖角正向誤差補償量 (85)Pr1381~Pr1400 圓弧尖角誤差補償時間常數 (85)Pr1361~Pr1400 圓弧尖角負向誤差補償量 (85)1.參數總表2.參數設定說明2.1 系統基本參數設定2.1.1 硬體環境設定軸卡基本參數設定2.1.1.1.1 Pr01 軸板基址1.Servo_4 軸卡對應 I/O 基址與跳線規則：軸卡二片以下 Pr01今800 軸卡超過二片 Pr01今7682.S ervo_6 的第一片軸卡基址為768(目前一部控制器僅支援一張 Servo_6，不可與 Servo_4 混插)3.E mbedded 第一片軸卡基址固定為5122.1.1.1.2 Pr09 軸板型態0:EMP21:SVO4+不檢查伺服警報2:SVO4+伺服警報接點為常開接點 Normal Open( A 接點)3:SVO4+伺服警報接點為常閉接點 Normal Close( B 接點)4:EMP45:SERVO69:虛擬軸卡2.1.1.1.3 Pr10 伺服警報接點型態0: SERVO 6 軸卡警報為常開接點 Normal Open( A 接點)1: SERVO 6 軸卡警報為常閉接點 Normal Close( B 接點)2.1.1.1.4 Pr11 軸卡時脈來源此參數為設定軸卡時脈來源：設定 0 為使用軸卡自已時脈設定 1 為共用控制器底板 IPC Bus 時脈設定 2 為共用主機板 VIA 時脈設定原則：一體機控制器今請設定『0』非一體機控制器今請設定『2』舊型 486 主機板控制器今請設定『1』2.1.1.1.5 Pr12 SERVO6 軸卡最高時脈此參數為設定 Servo6 軸版最高時脈。
科诚EZ1100PLUS打印机程序设置手册
E3 Plus EtherNet IP 适配器用户指南说明书
Installation InstructionsE3 Plus EtherNet/IP AdapterCatalog Number 2100-ENETTopic PageIntroduction1Important User Information2Adapter Components3Status Indicators4Set the IP Network Address4Install EDS File7Logix Controller I/O Messaging9Additional Resources12IntroductionThe E3 Plus EtherNet/IP adapter is a linking device that lets users connect an E3 or E3 Plus Solid State Overload or an 825-P Motor Protection System directly to an EtherNet/IP network. This document explains the basic steps needed to configure the E3 Plus EtherNet/IP adapter.2 E3 Plus EtherNet/IP AdapterImportant User InformationSolid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at /literature/) describes some important differences between solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable.In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment.The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams.No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual.Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited.Throughout this manual, when necessary, we use notes to make you aware of safety considerations.WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardousenvironment, which may lead to personal injury or death, property damage, or economic loss.ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death,property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard and recognize theconsequences.SHOCK HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to alert people thatdangerous voltage may be present.IMPORTANT Identifies information that is critical for successful application and understanding of the product.Rockwell Automation Publication 2100-IN090A-EN-P - February 2012E3 Plus EtherNet/IP Adapter 3Rockwell Automation Publication 2100-IN090A-EN-P - February 2012Adapter ComponentsThe adapter has these components.The E3+ and 825-P must be set to node 63 and have a communication rate of 500K (or have the autobaud enabled). This is the default state of each of these devices.ItemPartDescription1Status Indicators Four status indicators for the DeviceNet, adapter, and network connection.2E3 Connector This connector is provided for the connection to the E3 Plus or the 825-P .3Ethernet ConnectorAn RJ-45 connector for the Ethernet cable. The connector is CAT-5 compliant toensure reliable data transfer on 100Base-TX Ethernet connections.14 E3 Plus EtherNet/IP AdapterRockwell Automation Publication 2100-IN090A-EN-P - February 2012Status IndicatorsThe adapter uses four status indicators to report its operating status.Set the IP Network AddressThe E3 Plus EtherNet/IP adapter is shipped with Bootstrap Protocol (BOOTP) enabled. Y ou can set the network Internet Protocol (IP) address by using the BOOTP/DHCP server that is provided with RSLinx Classic software. This utility recognizes BOOTP-enabled devices and provides an interface to configure a static IP address for each device.T o assign network parameters via the BOOTP/DHCP utility, perform this procedure.1.Start the BOOTP/DHCP software.Item Name Color State Description1PORT Green Flashing Normal Operation. The adapter is establishing an I/O connection to the E3 Plus overload relay. It will turn steady green or red.2MOD SteadyNormal Operation. The adapter is properly connected and communicating with the E3 Plus overload relay.3NET A Green Flashing Normal Operation. The adapter is operating but is not transferring I/O data to a controller.4NET BSteadyNormal Operation. The adapter is operating and transferring I/O data to acontroller.Status IndicatorsE3 Plus EtherNet/IP Adapter 5Rockwell Automation Publication 2100-IN090A-EN-P - February 20122.Select T ool > Network Settings and enter the subnet mask for the network.If appropriate for the network, enter the gateway address, primary/secondary server addresses, and domain name.3.Click OK.The Request History panel displays the hardware addresses of devices issuing BOOTP or DHCP requests.4.Double-click the MAC address of the adapter to be configured.The MAC address is printed on the side of the E3 Plus EtherNet/IP adapter. The format of the hardware address resembles 00:00:BC:59:72:5A. The New Entry dialog boxappears with the module's Ethernet Address (MAC).6 E3 Plus EtherNet/IP AdapterRockwell Automation Publication 2100-IN090A-EN-P - February 20125.Enter the IP address for the adapter and, if appropriate, enter the host name and an adapter description.6.Click OK.Once the IP address you entered shows up in the Request History panel (you may need to cycle power to the adapter), this configuration can be permanently assigned to theadapter.7.T o do so, highlight the adapter in the Relation List panel and click Disable BOOTP/DHCP.8.Confirm that the Status panel message reads, ‘[Disable BOOTP] Command successful’. When the adapter power is recycled, it will use the assigned configuration and will not issue a BOOTP request. If you do not click Disable BOOTP/DHCP, the adapter clears the current IP configuration after a power cycle and will again begin sending BOOTP requests.E3 Plus EtherNet/IP Adapter 7Install EDS FileBefore the E3 Plus EtherNet/IP adapter is configured to communicate on an EtherNet/IP network, it must be registered to the software that configures the network, for example, RSLinx Classic software. Y ou can register the adapter by installing an electronic data sheet (EDS file). For the E3 Plus EtherNet/IP adapter, you will install an EDS file for the device that is connected to the adapter. Use the following procedure to download and register the EDS file for the E3 Plus EtherNet/IP adapter.Download EDS file from the EDS WebsiteThe EDS file for the device connected to the E3 Plus EtherNet/IP adapter can be found at /resources/eds/.1.When the web page for the link above comes up, enter the following information.E3 Plus Overload825-PNetwork EtherNet/IP EtherNet/IPDevice Type Motor Protector Motor ProtectorBulletin/Catalog No.2100-ENET2100-ENETMajor Revision(Leave Blank)(Leave Blank)Minor Revision(Leave Blank)(Leave Blank)Keyword(Leave Blank)(Leave Blank)2.Select the file that relates to the E3 or 825-P module that is connected to the2100-ENET unit.3.In the Details & Download column for the device, select Download.4.Click Save to save the EDS file to your personal computer.Register the EDS FileAfter the EDS file has been downloaded, you need to register the EDS file with the software that configures the EtherNet/IP network. Follow these steps to register an EDS file with RSLinx Classic software.1.Start the EDS Hardware Installation T ool at Start->Programs->RockwellSoftware->RSLinx->T ools.2.Click Add to register a new device.Rockwell Automation Publication 2100-IN090A-EN-P - February 20128 E3 Plus EtherNet/IP AdapterRockwell Automation Publication 2100-IN090A-EN-P - February 20123.Register a single file, browse to the location of the EDS file, and click Next.4.Click Next to accept the installation test results.5.Click Next to accept the graphic image.E3 Plus EtherNet/IP Adapter 9Rockwell Automation Publication 2100-IN090A-EN-P - February 20126.Click Next to register the device.7.Click Finish.Logix Controller I/O MessagingRSLogix 5000 software is used to configure I/O messaging between a Logix controller and an E3Plus EtherNet/IP adapter on an EtherNet/IP network. Follow these steps to configure a Logix controller for I/O messaging.1.Right-click on the EtherNet/IP scanner in I/O Configuration and select New Module to open the Select Module Type dialog box.2.Select Generic Ethernet Module and click OK.3.Enter a name for the E3 Plus EtherNet/IP adapter.The name creates a tag in RSLogix 5000 software that can be used to read and write data from the E3 Plus EtherNet/IP adapter.10 E3 Plus EtherNet/IP AdapterRockwell Automation Publication 2100-IN090A-EN-P - February 20124.Select Data-INT for the Comm Format.The Comm Format tells RSLogix 5000 software the format of the data. The Data-INT format represents the data from the E3 Plus EtherNet/IP adapter as a field of 16-bit values.5.Set the Connection Parameters.I/O data is accessed using Input Instance 100 and Output Instance 103 (for E3 standard) or 105 (for E3 Plus) by default. The size of the input connection and the output connection shall correspond to the size of the chosen instance. For Instance 100, the size is 6. For Instances 103 and 105, the size is 1. The E3 Plus EtherNet/IP adapter Configuration Assembly Instance is 6. Currently, the 2100-ENET adapter does not support the configuration assembly.IMPORTANTIf you have already changed the Input and Output Assemblies, you will need to enter thosevalues instead of the default values.E3 Plus EtherNet/IP Adapter 11Rockwell Automation Publication 2100-IN090A-EN-P - February 20126.Enter the IP address of the E3 Plus EtherNet/IP adapter.7.Click Next.Output Assembly - Instance 105BitContents 0OutA 1OutB 2Fault Reset 3Not Used 4Not Used 5Remote Reset 6Not Used 7Not UsedInput Assembly - Instance 100Byte SizeContents 2 BytesHeader information (Pad Word)2 BytesHeader information (Pad Word)2 BytesValue of parameter pointed to by parameter #612 BytesValue of parameter pointed to by parameter #622 BytesValue of parameter pointed to by parameter #632 Bytes Value of parameter pointed to by parameter #64Publication 2100-IN090A-EN-P - February 2012PN-112789Copyright © 2012 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.Allen-Bradley, Rockwell Software, Rockwell Automation, RSLinx, and RSLogix 5000 are trademarks of Rockwell Automation, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.8.Enter a value for the time between each scan of the adapter.Make sure Inhibit Module is not checked.9.Click Finish to add the E3 Plus EtherNet/IP adapter to the I/O Configuration in RSLogix 5000 software.Additional ResourcesThese documents contain additional information concerning related products from Rockwell Automation.Y ou can view or download publications at /literature/. T o order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative.ResourceDescription Ethernet Design ConsiderationsReference Manual, publication ENET-RM002Provides explanation of the following Ethernet concepts:•Network Layout and Components •Network Infrastructure Devices •Network Infrastructure Features •ProtocolIndustrial Automation Wiring and Grounding Guidelines, publication 1770-4.1Provides general guidelines for installing a Rockwell Automation industrial system.Product Certifications website, Provides declarations of conformity, certificates, and other certification details.。
科诚EZ1100plus设置通过Qlabel090518
通过Qlabel——IV设置Ez1100+1.安装软件，点击AutoRun.exe进入安装页面。
选择Qlabel——IV安装。
（见鲜绿色框）2.安装完桌面显示图标。
（见鲜绿色框）3.点击进入。
选择文件——>新建，进入以下界面。
在打印设定中，设置“标签设定”和“条码机设定”。
条码机设定中，把鲜绿色框内的参数设定好，应该就没有什么问题了。
1.关闭电源同时按FEED键，打开电源，等出6声后放开设置为热敏方式2．关闭电源同时按F EED键，打开电源，等出三声放开FEED键打印机自动检测3.关闭电源同时按F EED键，打开电源，当二个灯为桔红色时改成自测纸距方式4．在光盘的F:\Windows Drivers\Plus series\INSTALL_GODEX_NT目录中有打印机的驱动程序。
打印机型号选择EZ-1100+。
5．安装光盘的QLABEL-IV后可以打印条码。
在打印时选用热感式即为热敏方法打印。
6.使用该DLL调用之前必须先安装由Scientific Software Tools, Inc.所撰写的DLPortIO，档名为port95nt.exe。
若未先安装DLPortIO时，使用ez1100+.dll 则会出现”.dll not found” 的错误讯息。
上面小肖在2009年5月16日总结---下面是小蒋总结：200905181，按住feed，开机，当上下灯红黄放手---为打印自检，系统参数Senor on 错误—是投射模式响五声当上下灯绿红放手Senor off2，按住feed，开机，当上下灯黄黄灯放手---为打印机检测纸宽3，按住feed，开机，响三声当上下灯红红灯放手---为打印打印机打印的模式Dt mode 为热敏纸打印模式TT mode 为使用色带模式4，按住feed，开机，响六声当上下灯黄黄灯放手---转换打印机打印的模式，针对35，开机，按住feed ，不闪灯，变成两个绿灯的时候开机关机要等待一下？？？6，按feed 第一下没有问题，第二下红灯这个是什么问题例如打印驱动的打印测试页，第一张没有问题，第二张有问题？？？怀疑打印热感式打印，碳带感应器有可能坏，控制走纸的，不论哪种打印模式都需要7，注意条码纸，或者打印纸下方有一个感应器------一定要在纸张下面。
大恒SV系列摄像机使用说明书
电感耦合等离子体质谱仪技术参数
仪器技术参数技术规格1.仪器应用要求1.1本仪器要求能适用于应用领域广泛的各种样品的元素分析、同位素分析和元素形态分析任务,满足环保、食品、地质、金属、生物样品、化工材料分析等等。
2.仪器工作环境2.1工作环境温度：15-30°C.2.2工作环境湿度:<80%（无冷凝）2.3电源:单相200-240V,50Hz3.仪器规格要求：3.1仪器硬件;3.1.1雾化器:高效率PFA同心雾化器，提供最佳的雾化效率。
3.1.2雾化室:小体积旋流型雾化室,死体积小,低记忆效应,带半导体制冷装置，对雾化室制冷控温范围-10~20C，用于精确控制雾化室温度，消除由于实验室条件的波动所引起的任何漂移，并提升仪器长期的稳定性。
*3.1.3等离子体可视系统:具有PlasmaTV功能，可以实时监控等离子体状态。
3.1.4接口:拥有两种不同类型的接口技术,接口采用耐高盐设计,截取锥口径范围0.5~0.75mm,保证长期分析高盐样品的稳定性，满足高通量分析与大进样量的要求。
3.1.5仪器主机ICP部分,配置质量流量计:包括等离子体气，辅助气,雾化气3路质量流量计。
*3.1.6离子源：自激式全固态RF发生器，频率为27.12MHz,采用变频技术快速匹配,适用乙腈等有机试剂直接进样。
*3.1.7真空系统:要求从大气压开始抽至可工作的真空度的时间小于15分钟。
滑动阀关闭后，静态真空度维持在＜6X10-8mbar（滑阀关闭）。
*3.1.8离子光学:低背景的90度偏转加离轴偏转透镜或双离轴偏转透镜设计。
3.1.9四极杆材料:纯Mo材料四极杆。
3.1.10偏转透镜、碰撞反应池和四极杆质量分析器均为免拆洗维护。
3.1.11脉冲模拟双模式同时型电子倍增器,必须可以在一次进样过程中同时完成扫描和跳1峰分析（定性和定量分析）,同时可以自动在模拟和脉冲模式之间实现切换。
3.1.12等离子体炬位调整：由计算机控制步进电机进行三维（X,Y,Z方向）位置控制,参数存储于计算机软件中。
电感耦合等离子体质谱仪
电感耦合等离子体质谱仪1 仪器总体要求*1.1 电感耦合等离子体质谱仪要求为“三重四极杆串联质谱仪或“双重四级杆+单八级杆”的串联四级杆质谱仪，而非普通的单极四极杆质谱仪；*1.2 第一重四极杆-四级杆离子选择偏转器，可以实现将所需的特定质荷比的离子依次进入第二重四极杆的反应池内；1.3 第二重四极杆-通用池，通过反应气与待分析离子相同质荷比的干扰离子反应产生新的不同质荷比的离子，通过四极杆质量扫描过滤，彻底消除干扰物和反应副产物，只允许待分析的离子进入第三重四极杆；1.4 第三重四极杆-质量分析器，将待分析的单原子离子依次分开进行检测；1.5 具有彩色等离子体观测窗，无需打开仪器，可对锥、炬管和负载线圈进行观测，使等离子体采样深度的优化和有机物的分析简单、方便。
同时可实时监测锥孔及喷射管孔样品沉积情况，便于维护和清洗；1.6 电感耦合等离子体质谱仪具有与高效液相色谱技术联机进行元素价态、结合形态的分析能力，具有专业的形态分析软件；1.7 仪器要求能进行样品定性、半定量、定量、同位素比、同位素稀释、单颗粒分析、单细胞分析。
1.8 至少能用于硫和磷同位素标记的定量研究；1.9 能够分析纳米材料的元素组成与浓度、尺寸及其尺寸分布。
2 仪器工作环境2.1 工作环境温度：15-30℃。
2.2 工作环境湿度：＜80% （无冷凝）。
2.3电源：单相200-240V，50 Hz。
3 技术要求3.1 仪器硬件3.1.1 雾化器：高效石英或PFA同心雾化器；3.1.2 雾化室：小体积石英旋流雾化室；*3.1.3 全基体进样系统控制气路：可实现样品气体稀释，稀释倍数大于100倍；可通入氧气，实现有机样品的直接进样分析；可通入甲烷气，实现难电离元素，如砷、硒等元素的超痕量分析；3.1.4 等离子体可视系统：可以从实际观测窗中实时监控等离子体状态；*3.1.5 接口设计：为实现对离子射束紧凑控制，接口至少采用三级锥设计，应至少包括一个采样锥、一个截取锥和一个超级锥或嵌片。
北京亿兆未来宽带网络技术有限公司CHAS02集中式局端设备
设备名称 KPOWER DC KPOWER AC
KNM KCONV1035A KCONV1035B KCONV1035U
KS-CONV
KSVPE10A KSVPE10AF KSVPE10C KSVPE10CF KSVPE20A KSVPE20C KSVPE40A KSVPE40C
KSVPE51
5×E1 +1×Ether
业务
8×E1 +1×Ether
1×E1 1×V.35
说明 直流-48V 交流 220V 以太网或 RS232 接口可选 单 E1 到 V.35 转换器，N×64K（N = 1~32），无网管 单 E1 到 V.35 转换器，N×64K（N = 1-32） 单 E1 到 V.35 转换器，非成帧 2M，无网管
15.1 供电条件 .......................................................................................................... 错误！未定义书签。 15.2 工作环境.........................................................................................................错误！未定义书签。 15.3 外形尺寸.........................................................................................................错误！未定义书签。
意安全标识。并保存好本手册，以备将来参考用。
文档说明：
PROLINE TLW 1000P-E 洗衣机说明书
MARQUE: PROLINE REFERENCE: TL W 1000P-ECODIC: 3699498F5019 612 10256A. Sélecteur de programmeB. Indicateurs de déroulement du programmeC. T ouche “Départ/Pause”D. T ouche “Annulation”E. Voyant “Porte ouverte”N.B. Cette machine est contrôlée par des capteurs. Veuillez éviter un dosage excessif de détergent.TABLEAU DES PROGRAMMESABHFE G CDbien verrouillés.2. Versez le détergent et les produits additifs dans lebac à produits comme suit, sans dépasser le repère“MAX”:•Lessive pour prélavage et lavage principal•Lessive pour lavage principal sans prélavage•Assouplissant et produit amidonnant•Détachants•Anticalcaires (si nécessaire)3. Fermez le couvercle.4. T ournez le sélecteur de programme jusqu'auprogramme et température désiré. Le voyant prèsde la touche to the “Départ/Pause” clignote.programme, le voyant est allumé pour indiquer que lecouvercle peut être ouvert. Tant qu‘un programme delavage est en cours, le couvercle reste verrouillé et nepeut en aucun cas être forcé. Si vous devez absolumentl‘ouvrir alors qu‘un programme est en cours, consultez lechapitre “Annulation (RAZ) d‘un programme avant la fin”.option à n'importe quelle phase du programme.L'option peut être activée aussi longtemps que laphase du programme correspondante n'est pasencore exécutée.T ouche “Essorage pour préserver votre linge.T ouche “Arrêt cuve pleine”• Le linge non essoré reste dans la dernière eau derinçage, permerrant ainsi d’éviter la formation defaux plis et la décoloration du linge.• Cette option est particulièrement conseillée pour lesprogrammes “Synthétiques” et ”Délicat”.• Elle est utile si vous désirez remettre l‘essorage àplus tard ou ne pas essorer.• Si l‘option “Arrêt cuve pleine” est sélectionnée, nelaissez pas le linge trop longtemps dans l‘eau.• Dès que la machine s‘arrête à la phase “Arrêt cuvepleine”, le voyant de “arrêt cuvePleine” de l‘indicateur de déroulement duprogramme s‘allume et le voyant près de la touche“Départ/Pause” clignote.Pause”. Le voyant situé près de la touche “Départ/Pause” s’allume. L’indicateur de déroulement duprogramme indique la phase du programme en cours, etse déplace de gauche à droite en passant par les phasesde lavage, rinçage et essorage/vidange. Dès que la phasedu programme est terminée, le voyant correspondants’éteint.•Remarque: en cas de panne de courant ou dedéconnexion de l'appareil pendant le cycle, leprogramme redémarrera au point où il a étéinterrompu.programme sont éteints et le voyant “Porte ouverte”est allumé.1. T ournez le sélecteur de programme sur “Off/O”.2. Fermez le robinet.3. Ouvrez le couvercle et le tambour et sortez le linge.4. Laissez le couvercle ouvert pour permettre autambour de sécher.démarrer le programme. Le voyant s’allume.2. Sélectionnez un autre programme, d‘autres optionssupplémentaires et - si vous le souhaitez - une autrevitesse d’essorage.3. Appuyez de nouveau sur la touche “Départ/Pause”.Le nouveau programme démarrera là où leprogramme précédent a été interrompu. N’ajoutezpas d’autre détergent pour ce programme.la fin. Appuyez sur la touche “Annulation” pendant aumoins 3 secondes. L’eau résiduelle est évacuée avant quele hublot ne puisse être ouvert.Pour supprimer l’option “Arrêt cuve pleine”:• Appuyez sur la touche “Départ/Pause”; leprogramme se terminera automatiquement par lecycle d’essorage sélectionné pour le programme delavage.• Si vous ne désirez pas essorer les vêtements,tournez le sélecteur de programme jusqu’auprogramme “Vidange” et appuyez sur la touche“Départ/Pause”.d’utiliser “Le guide de recherche des défauts” dans votrenotice d’utilisation.Voyant “Service”L’allumage du voyant “Service” peut être déclenché parun défaut de fonctionnement d’un composant électrique.Consultez le chapitre “Diagnostic rapide” dans la noticed’utilisation; si le problème persiste, contactez le ServiceAprès-vente.“Robinet d’eau fermé”L’eau n’entre que lentement ou pas du tout. Ouvrez lerobinet; si le voyant reste allumé, consultez le chapitre“Diagnostic Rapide” dans la notice d’utilisation.“Nettoyage Filtre”La vidange de l’eau ne s’effectue pas. Vérifiez si letuyau de vidange n’est pas plié ou si le filtre ne doit pasêtre nettoyé; dans ce dernier cas, consultez la Noticed’utilisation(“Nettoyage du filtre”).Les données relatives à la consommation d'eau et d'énergie ont été mesurées dans les conditions normales prévues par la norme CEI/EN 60 456. Ces valeurspeuvent toutefois varier en fonction de la pression de l'eau, de la charge et du type de linge. La consommation d’eau et d’énergie se fait avec le réglage standard descommandes des programmes; la selection des options spécifiques ou le changement de la vitesse de rotation ou de la température impactent sur cette consommation.La durée du programme peut varier par rapport aux valeurs ci-dessus, car elle depend des conditions réelles de travail (voir “Leguide de la recherche des défauts” dans votre Notice d’utilisation).* Afin de réduire la température de l’eau, un peu d’eau froide est ajoutée à la fin du cycle de lavage, avant la vidange de la cuve.** Les programmes de référence pour le label énergétique.5019 612 10256。
GODEX EZ-1000Plus 说明书
操作手冊 ArrayEZ-1000PlusRev. C, 06.2009FCC COMPLIANCE STATEMENTFOR AMERICAN USERSThis equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at own expense.EMS AND EMI COMPLIANCE STATEMENTFOR EUROPEAN USERSThis equipment has been tested and passed with the requirements relating to electromagnetic compatibility based on the standards EN 55022:1998+A1:2000+A2:2003, CISPR 22 , Class A EN 55024:1998+A1:2001+A2:2003, IEC 61000- 4 Series EN 61000-3-2 / 2000 & EN 61000-3-3 / 1995. The equipment also tested and passed in accordance with the European Standard EN55022 for the both Radiated and Conducted emissions limits.EZ PLUS SERIESTO WHICH THIS DECLARATION RELATESIS IN CONFORMITY WITH THE FOLLOWING STANDARDSEN55022 : 1998,CLSPR 22, Class A / EN55024 : 1998IEC 61000-4 Serial / EN61000-3-2 : 2000 / EN 6100-3-3 : 1995 / CFR 47, Part 15/CISPR 22 3rd Edition : 1997, Class A / ANSI C63.4 : 2001 / CNS 13438 / IEC60950-1 : 2001 / GB4943 : 2001 / GB9254 : 1998 / GB17625.1 : 2003 /EN60950-1 : 2001CAUTIONDanger of explosion if battery is incorrectly replacedReplace only with the equivalent type recommended by the manufacture.Dispose of used batteries according to the manufacturer’s instructions.Specifications are subject to change without notice.Bitte die Sicherheitshinweise sorgfältig lesen und für später aufheben.1. Die Geräte nicht der Feuchtigkeit aussetzen.2. Bevor Sie die Geräte ans Stromnetz anschließen, vergewissern Sie Sich, dass dieSpannung des Geräts mit der Netzspannung übereinstimmt.3. Nehmen Sie das Gerät bei Überspannungen (Gewitter) vom Netz. Das Gerät könntesonst Schaden nehmen.4. Sollte versehentlich Flüssigkeit in das Gerät gelangen, so ziehen sofort denNetzstecker. Anderenfalls besteht die Gefahr eines lebensgefährlichen elektrischen Schlags.5. Wartungs- und Reparaturarbeiten dürfen aus Sicherheitsgründen nur vonautorisierten Personen durchgeführt werden.6. Bei Wartungs- und Reparaturarbeiten müssen die Sicherheitsvorschriften derzuständigen Berufsverbände und Behörden unbedingt eingehalten werden.7. Bei Verletzungen unbedingt den Arzt aufsuchen und die gegebenenfalls diezuständigen Stellen benachrichtigen. Unterlassung kann zum Verlust derVersicherungsleistungen führen.Please read the following instructions seriously.1. Keep the equipment away from humidity.2. Before you connect the equipment to the power outlet, please check the voltage of thepower source.3. Disconnect the equipment from the voltage of the power source to prevent possibletransient over voltage damage.4. Don’t pour any liquid to the equipment to avoid electrical shock.5. ONLY qualified service personnel for safety reason should open equipment.6. Don’t repair or adjust energized equipment alone under any circumstances. Someonecapable of providing first aid must always be present for your safety7. Always obtain first aid or medical attention immediately after an injury. Never neglectan injury, no matter how slight it seems.安全须知请仔细阅读以下说明。
CPL WiFi 1000 模型 PL1000v2 和 PLW1000v2 快速启动指南说明书
1. Branchez l'adaptateur dans une prise murale pour laquelle vous souhaitez ajouter un accès Internet.
1. Appuyez pendant 2 secondes sur le bouton WPS du point d'accès CPL. Le voyant WiFi se met à clignoter.
2. Appuyez pendant 2 secondes sur le bouton WPS de votre appareil compatible Wifi et relâchez-le. Quand le voyant WiFi cesse de clignoter, votre appareil WiFi est automatiquement connecté au point d'accès CPL et vous pouvez naviguer sur Internet.
connectez-vous à votre nouveau réseau WiFi CPL par Wifi. Félicitations. Vous avez installé vos adaptateurs et configuré votre réseau. Vous pourrez personnaliser les paramètres réseau et de sécurité plus tard.
Rouge. Débit de connexion < 50 Mbit/s (bonne connexion).
灯型号——精选推荐
灯型号Standard Mercury V apour标准汞蒸气Osram Philips Sylvania GE ThornHQL 50 HPLN 50 HSLBW 50 HR 50/27 MBF 50WHQL 80 HPLN 80 HSLBW 80 HR 80/27 MBF 80WHQL 125 HPLN 125 HSLBW 125 HR 125/27 MBF 125WHQL 250 HPLN 250 HSLBW 250 HR 250DX37 MBF 250WHQL 400 HPLN 400 HSLBW 400 HR400DX33 MBF 400WHQL 700 HPLN 700 HSLBW 700 MBF 700WHQL 1000 HPLN 1000 HSLBW 1000X HR1000DX34 MBF 1000WSelf Ballasted Mercury V apour自碴汞蒸气Osram Philips Sylvania GE ThornHWL 160W 235V ML 160W HSB-BW 160W HMLI 160/230-240HWL 250W 235V ML 250W HSB-BW 250W HMLI 250/230-240HWL 500W 235V ML 500W HSB-BW 500W HMLI 500/230-240High Pressure Sodium Elliptical高压钠灯椭圆Osr am Philips Sylvania GE Thor nNAV E 50 4Y SON50W PIANAV E 50/E SON50W-E SHP-S 50W CO/E LU 50/90/D/27 SONE50 NAV E 50/I 4YNAV E 50/I SON50W-1 SHP 50W CO/I LU50/90/D/I/27 SONE50COI NAV E 70 4Y SON70W PIANAV E 70/E SON70W-E SHP-S 70W CO/E LU 70/90/D/27 SONE70 NAV E 70/I 4YNAV E 70/I SON70W-1 SHP70CO/I LU 70/90/D/I/27 SONE70CDI NAV E 100 Super SON100 PIA Plus LU 100/100/HO/D/40NAV E 110 SPX E CO ARC 98WNAV E 150 4Y SON150W PIANAV E 150/E SON150W SHP E150 LU 150/100/D/40 SONE150 NAV E 150 Super SON150 PIA Plus LU 150/100/HO/D/50NAV E 150/I SON150W-1NAV E 210 (1) SONH 210 SPX E CO ARC 190W LUH 215/D/EZ/40NAV E 250 4Y SON250W PIANAV E 250/e SON250W SHP E250 LU 250/D/40 SONE250 NAV E 250 Super SON250W PIA Plus LU 250/HO/D/40NAV E 250/I SON250-1NAV E 350 (1) SONH350 SPX E CO ARC 295WNAV E 400 4Y SON400W PIANAV E 400/E SON400W PIA SHP E 400 LU 400/D/40 SONE400 NAV E 400 Super SON400W PIA Plus LU 400/HO/D/40NAV E 400/I SON 400W-1NAV E 1000 SON 1000W LU 1000/110/D/40 SONE1000 (1) Retr ofit HPS lamp to be oper ated on mec ury vapour c ontr ol gearHigh Pressure Sodium Tubular高压管形钠Osr am Philips Sylvania GE Thor nNAV T 50 Super 4Y SON T 50 PLUS SHP-TS-50/CL/ELU 50/85/HO/T/27 SON T 50NAV T 70 Super 4Y SON T 70 PLUS SHPT70CL/E LU 70/90/HO/Y/27 SON T 70 NAV T 100 Super 4Y SON T 100 PLUS SHPT100 LU 100/100/HO/T/40 SON T 100 NAV T 150 4Y SON T 150 PIANAV T 150 SON T 150 SHPT150 LU 150/100/D40 SON T 150 NAV T 150 Super 4Y SON T 150 PLUS LU 150/100/HO/T/40NAV T 250 4Y SON T 250 PIANAV T 250 SON T 250 SHPT250 LU 250/40 SON T 250 NAV T 250 Super 4Y SON T 250 PLUS LU 250/HO/T/40NAV T 250/I SON T 250-1NAV T 400 4Y SON T 400 PIANAV T 400 SON T 400 SHPT400 LU 400/40 SON T 400NAV T 400 Super 4Y SON T 400 PIA PLUS LU 400/HO/T/40NAV T 400/I SON T 400-1NAV T 600 Super 4Y SON T 600 PIA PLUS SHP-TS-600 LU 600/HO/T/40NAV T 1000 SON T 1000 SON T 1000Low Pressure Sodium低压钠Osram Philips Sylvania GE Thorn SOX 18W SOX 18W SOX 18W SOX 18 SOX 35W SOX 35W SOX 35W SOX 35 SOX 55W SOX 55W SOX 55W SOX 55 SOX 90W SOX 90W SOX 90W SOX 90 SOX E 26W SOX E 26WSOX 135W SOX 135W SOX 135W SOX 135 SOX 180W SOX 180W SOX 180W金属卤化物灯North American Metal Hallide Lamps北美金属Hallide灯Osr am Philips Sylvania GE Thor n StandardMI 175W/U M175/U MVR175/U MH175UMI 250W/U M250/U MVR250/U MH250UMI 250W/C/U MH 250 CUE 40 M250/C/U MVR250/C/U MH250CUMI 400W/U HPI 400WBU M400/U MVR400/U/I MH400UMI 400W/C/U MH 400 CUE 40 M400/C/U MVR400/C/U MH400CUMI 1000W/U M1000/U MVR1000/U MH1000BU High Output高输出MIS 400W/BU MS400/BUMIS 400W/C/BU MS400/C/BU MVR 400/C/VBU/40MIS 1000W/BU MS1000/BUDouble E nded双端MI 1500/T7/DE M 1500/T7/DE MVR1500/T7/DEMI 2000/T8/DE M 2000/T8/DE MVR 2000/T8DEMI 2000/T9/DE M 2000/T9/DE MVR 2000/T9DEEuropean Metal Hallide Lamps欧洲金属Hallide灯Osram Philips Sylvania GE Thorn Tubular 35 - 150W 管状35 -150WHCI-T 35W/WDL CDM T 35W/830 CMI-T-35W/WDL G12 CMH35/T/UVC/U/830/G12HCI-T 70W/WDL-PB CDM T 70W/830 CMI-T-70W/WDL G12 CMH70/T/UVC/U/830/G12HCI-T 70W/NDL-PB CDM T 70W/942 CMI-T-70W/NDL CMH35/T/UVC/U/830/G12HCI-T 150W/WDL-PB CDM T 150W/830 CMI-T-150W/WDL CMH35/T/UVC/U/942/G12HCI-T 150W/NDL-PB CDM T 150W/942 CMI-T-150W/NDL CMH150/T/UVC/U/830/G12HCI-TC 35W/WDL CDM TC 35W/830 CMI-TC-35W/WDL G8.5 CMH35/TC/UVC/830/G8.5HCI-TC 70W/WDL-PB CDM TC 70W 830 CMI-TC-70W/WDL G8.5 CMH70/TC/UVC/830/G8.5HCI-TT 70W/WDL-PB CDM TT 70W/830HCI-TT 150W/WDL-PB CDM TT 150W/830Double Ended 70 - 150W双端70 -低至150WHCI-TS 70W/WDL-PB CDM TD 70W/830 CMI-TD-70W/WDL CMH70/TD/UVC/830/RX7s HCI-TS 70W/NDL-PB CDM TD 70W/942 CMI-TD-70W/NDL CMH70/TD/UVC/942/RX7s HCI-TS 150W/WDL-PB CDM TD 150W/830 CMI-TD-150W/WDL CMH150/TD/UVC/830/RX7s-24 HCI-TS 150W/NDL CDM TD 150W/942 CMI-TD-150W/NDL CMH150/TD/UVC/942/RX7s-24 PAR 35 - 70WHCI-PAR20 35W/WDL FL CDM-R 35W/830PAR20L30DGCMH35/PAR20/UVC/830/E27/FLHCI-PAR20 35W/WDL SP CDM-R 35W/830PAR20L10DGCMH35/PAR20/UVC/830/E27/SPHCI-PAR30 35W/WDL FL CDM-R 35W/830PAR30L30DGCMH35/PAR30/UVC/830/E27/FLHCI-PAR30 35W/WDL SP CDM-R 35W/830PAR30L10DGCMH35/PAR30/UVC/830/E27/SPHCI-PAR30 70W/WDL FL CDM-R 70W/830PAR30L30DGCMH70/PAR30/UVC/830/E27/FLHCI-PAR30 70W/WDL SP CDM-R 70W/830PAR30L10DGCMH70/PAR30/UVC/830/E27/SPElliptical 70 - 150W椭圆70 -低至150WHCI-E/P 70W/WDL Coated PB CMH70/E/UVC/U/830/E27/DB HCI-E/P 70W/WDL Clear PBHCI-E/P 100W/WDL PB CMH100/E/UVC/U/830/E27/DHCI-E/P 150W/WDL Coated PBHCI-E/P 150W/WDL Clear PBHCI-E/P 150W/NDL Coated PBHCI-E/P 150W/NDL Clear PBCer am ic 250W 陶瓷250WHCI-T 250W/WDL-PBHCI-E 250W/WDL-PBHCI-TS 250W/WDL-PBMetal Hallide - Quartz Arc Tube金属Hallide -石英电弧管Osr am Philips Sylvania GE Thor nTubular 70 - 150W 管状70 -150WHQI T 70W/WDL MHNT70/3K HSI-T70W3K MBI70/T/30 MBIT703000UHQI T 70W/NDL MHNT70/4K HSI-T70W4K MBI70/T/40 MBIT704000UHQI T 150W/WDL MHNT150/3K HSI-T150W3K MBI150/T/30 MBIT1503000UHQI T 150W/NDL MHNT150/4K HSI-T150W/4K MBI150/T/40 MBIT1504000U Double Ended 70 - 150W双端70 -低至150WHQI TS 70W/WDL MHWTD70/3K HSITD70W3K MQI/70/T6/30 MH70TDWDLHQI TS 70W/NDL MHWTD70/4K HSITD70W4K MQI/70/T6/43 MH70TDNDLHQI TS 150W/WDL MHWTD150/3K HSITD150W3K MQI/150/T7/30 MH150TDWDLHQI TS 150W/NDL MHWTD150/4K HSITD150W4K MQI/150/T7/43 MH150TDNDL Elliptical 70 - 150W椭圆70 -低至150WHQI E 70W/WDL Clear HSI-MP75W/CL U-E27HQI E 70W/WDL Coated HSI-MP75W/CO U-E27HQI E 70W/NDL Clear MVR 70/U/MEDHQI E 70W/NDL Coated MVR 70/C/U/MEDHQI E 100W/WDL Clear HSI-MP100W/CL U-E27HQI E 100W/WDL Coated HSI-MP100W/CO U-E27HQI E 100W/NDL Clear MVR 100/U/MEDHQI E 100W/NDL Coated MVR 100/C/U/MEDHQI E 150W/WDL Clear HSI-MP150W/CL U-E27HQI E 150W/WDL Coated HSI-MP150W/CO U-E27HQI E 150W/NDL Clear MVR 150/U/MEDHQI E 150W/NDL Coated MVR 150/C/U/MEDElliptical 250 - 400W椭圆250 - 400WHQI E 250W/D HSI-SX-250/CO (250HPS) ARC250/D/H/740/E40 MB/F/D 250 HQI E 400W/D HSI-SX-400/CO (400HPS) MB/F/D 400 HQI E 250W/N ClearHQI E 250W/N CoatedHQI E 250W/N/SI BU HPI 400 BUTubular 250 - 400W管状250 - 400WHQI T 250W/N/SI HPI T 250 BUHQI T 400W/BLUEHQI T 400W/GREENHQI T 400W/N CLEAR HSI-TSX-400/CL (400HPS) MBI400/THQI T 400W/N/SI HPI T 400 BUTubular 1000 - 3500W管状1000 - 3500WHQI T 1000W/D SPL 1000/T/H/960/E40 HQI T 2000W/D HSI-T-2000W-S4K 380V SPL 2000/T/H/960/E40 HQI T 2000W/D/IHQI T 2000W/N SPL 2000/I/T/H/960/E40 HQI T 2000W/N 230V 4X1 HPI T 2000/230V HSI-T 2000W/4K/230VHQI T 2000W/N/E Super HSI-T 2000-4K 380VHQI T 3500W/DDouble Ended 250 - 400W双端250 - 400WHQI TS 250W/DHQI TS 250W/NDL UVS MHN TD 250 HIS-TD 250W/NDL 4K UVS MBI 250/TD/840 Fc2HQI TS 250W/WDL UVS MHW TD 250 HIS-TD 250W/NDL 3K UVS MBI 250/TD/830 Fc2HQI TS 400W/DHQI TS 400W/NDLDouble Ended 1000 - 2000W双端1000 - 2000WHQI TS 1000W/D/SHQI TS 2000W/DHQI TS 2000W/D/S HIS-TD 2000W/D。
沃尔夫工具集成系统手册说明书
Tools Required: Hex Keys: 1/16", 7/64"
Parts May Be Required: Blade: K83987 Cap Screw: M54587 Set Screw: A02887
Special Instructions: It is critical the knife and blade be assembled with a zero-gap to ensure clean cut-off. Once correctly positioned, use threadlocking compound to prevent parts from shifting during use (allow sufficient time for compound to cure).
1
8
A91987 SCREW, FLAT, #6-32 X 1/4L
6
9
A92177 LINK, MIDDLE, CUTOFF
1
10
A92267 TENSION ARM, FRONT/SIDE LOAD TOOL
2
11
A92387 DECAL, TENSION INDICATOR
1
12
A92487 TENSION PLUNGER
www.
Page 3 of 5
Document # M50350 rev. F Copyright
BAND-IT-IDEX, Inc. 2012 All rights reserved
Blade Installation Procedure
M50389 Multi-Lok Tool
3
3
Zoom 双电源说明书
U se the following instructions to operate the power supply for high voltage/low current and low voltage/high current applications using Constant Operation (below) with one voltage limit, current limit, and power limit for the entire length of the electrophoresis or Programmable Mode (reverse side) for applications that require varying limits of voltage (V), current (mA), or power (W) during specified periods of time as discrete changes (STEP) or as gradients (RAMP). For more information and detailed instructions, refer to the ZOOM ® Dual Power manual, available at /manuals .•Use the Pause key, Start/Stop key, and output jacks on the left side of the instrument for high voltage/low current applications.4.Press F1 on the Set Constant Limits Screen to advance to the Running Screen .• If you intend to run an operation with very low current (<0.01 mA), for example isoelectric focusing, press F2 to DISABLE the No Load detection alarm before starting electrophoresis. When disabled, the screen will display No Load DISABLE .key to stop electrophoresis prior to reaching its programmed end or to clear the “FINISH” display and stop the audio signal that occur upon completing an operation.6. Running Page - Start, Stop, and PauseSet Constant Limits Screen - toggling between minutes (Min.) and volt-hours (V •Press the key to start electrophoresis.key to temporarily interrupt power to an electrophoretic run in progress without terminating the operation. Press the PAUSE key again to resume the operation without resetting the timer.5. Running Screen - toggling between ENABLE or DISABLE the No Load detection alarm• The alarm is automatically reactivated if electrophoresis is interrupted by pausing or stopping the run and must be disabled manually again before resuming electrophoresis.Disengage any unused leads and electrophoresis units before starting an operation when the No Load detection alarm is DISABLED.• Press the • Press theGeneral Instructions•Use the power switch located on the rear side of the power supply to turn on the instrument. Upon start-up, the Main Menu Screen appears.Set Constant Limits ScreenRunning Screen For best results, we recommend using time (Min.) with Life Technologies electrophoresisQUICK REFERENCEZOOM ® Dual Power SupplyCatalog Numbers ZP10001, ZP10002Document Part Number 25-0864 Publication Number MAN0007504 Rev. 3.0For research use only. Not for use in diagnostic procedures.Programmable Mode1. Press F2 to select Programmable Mode from the Main Menu Screenoptions2. Set Program Limits Screen - choosing Memory No. and Limits for electrical parameters• You can choose from 16 Memory Nos. (0–15) on each side of the instrument. To save a program, choose from Memory Nos. 1–15. Use Memory No. 0 for immediate use; this program will not be stored.• Follow the instructions in Step 2 of Constant Operation (see reverse side) to set parameters.3. Set Program Limits Screen- choosing limiting electrical parameters•For the Constant Mode, the default setting is voltage (V) with Limit 1 in current (mA) and Limit 2 in power (W).•Use the keys to move the cursor to the Constant Mode parameter.• Press F3once to change the Constant Mode parameter tocurrent (mA) with Limit 1 in voltage (V) and Limit 2 in power (W). Press F3 once again to change the Constant Mode parameter to power (W) with Limit 1 in voltage (V) and Limit 2 in current (mA).4. PressF1 on the Set Program Limits Screen to advance to theProgramming Screen.6. Programming Screen - toggling between RAMP and STEP settings•The STEP setting (for discrete changes of parameter values) is activated by default on the Programming Screen (dashed lines in the P2 column).•Press F3 to activate the RAMP function (an underlined numeric value appears). Use the SET key and up and down arrow keys to enter the RAMP endpoint value.• Use the directional arrow keys to move the cursor in the P2 column to the row corresponding to the step for which you want to apply the RAMP function (for a gradual, linear change of the parameter towards the selected end-point).7. Programming Screen - toggling between minutes (Min.) and volt-hours (V-H or V .H.)•By default, the Min. column is activated (dashed lines in the V-H column). Note: For best results, we recommend using time (Min.) with Life Technologies electrophoresis products.•Press F3 to switch between activation of Min. and V-H in the targeted Step. Activated cells display a numeric value. Inactive cells display “- - - - -“.• Use the SET key and up and down arrow keys to set the desired duration values.•Use the directional arrow keys to move the cursor in the Min. or V-H column to the row corresponding to the program Step you want to set.9. Running Screen - toggling between NO LOAD detection alarm ENABLED/DISABLED• If you are performing a run with very low current, press F2 to DISABLE the No Load detection alarm. “No Load DISABLE” will appear on the screen.See Step 5 of Constant Operation (reverse side) for further important information about the No Load detection alarm.Use the Programmable Mode if your application requires varying limits of voltage (V), current (mA), orpower (W). See reverse side for General Instructions .Main Menu ScreenSet Program Limits Screen Programming ScreenRunning Screen•Use the F2 key on the left hand side to run a high voltage/low current application.• Use the F2 key on the right hand side to run a low voltage/high current application.For support visit /support 19 December 2012Limited Product WarrantyLife Technologies Corporation and/or its affiliate(s) warrant their products as set forth in the Life Technologies’ General Terms and Conditions of Sale found on Life Technologies’ website at /termsandconditions. If you have any questions, please contact Life Technologies at /support.© 2012 Life Technologies Corporation. All rights reserved. The trademarks mentioned herein are the property of Life Technologies Corporation or their respective owners.DISCLAIMER - LIFE TECHNOLOGIES CORPORATION AND/OR ITS AFFILIATE(S) DISCLAIM ALL WARRANTIES WITH RESPECT TO THIS DOCUMENT, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. TO THE EXTENT ALLOWED BY LAW, IN NO EVENT SHALL LIFE TECHNOLOGIES AND/OR ITS AFFILIATE(S) BE LIABLE, WHETHER IN CONTRACT, TORT, WARRANTY, OR UNDER ANY STATUTE OR ON ANY OTHER BASIS FOR SPECIAL, INCIDENTAL, INDIRECT, PUNITIVE, MULTIPLE OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THIS DOCUMENT, INCLUDING BUT NOT LIMITED TO THE USE THEREOF.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
EZ1000 PLUS条码机操作手冊USER MANUAL VERSION ISSUE DATEP/N : EZ1000 Plus : Rev. D: 2013.10.22:920-012431-04FCC COMPLIANCE STATEMENTFOR AMERICAN USERSThis equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at own expense.EMS AND EMI COMPLIANCE STATEMENTFOR EUROPEAN USERSThis equipment has been tested and passed with the requirements relating to electromagnetic compatibility based on the standards EN 55022:2006/A1:2007 Class A, EN61000-3-2:2006/A2:2009, EN 61000-3-3:2008 and EN55024:1998/A1:2001/A2:2003(IEC 61000-4-2:2001 ED. 1.2 series. The equipment has also been tested and passed in accordance with the European Standard EN55022 for both radiated and conducted emissions limits.EZ PLUS SERIESTO WHICH THIS DECLARATION RELATESIS IN CONFORMITY WITH THE FOLLOWING STANDARDSIEC 60950-1:2005(2nd Edition)+Am 1:2009, GB4943.1-2011 GB9254-2008 (Class A) GB17625.1-2003, EN 55022:2006/A1:2007 Class A, EN61000-3-2:2006/A2:2009, EN 61000-3-3:2008 and EN55024:1998/A1:2001/A2:2003, IEC 61000-4-2:2001 series, UL 60950-1, 1st Edition, 2007-10-31, CSA C22.2 No. 60950-1-03, 1st Edition, 2006-07, CFR 47, Part 15WARNINGThis is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.此为Class A产品，在生活环境中，该产品可能造成无线电干扰，在这种情况下，可能需要用户对其干扰采取切实可行的措施。
Bitte die Sicherheitshinweise sorgfältig lesen und für später aufheben.1.Die Geräte nicht der Feuchtigkeit aussetzen.2.Bevor Sie die Geräte ans Stromnetz anschließen, vergewissern Sie Sich, dassdie Spannung des Geräts mit der Netzspannung übereinstimmt.3.Nehmen Sie das Gerät bei Überspannungen (Gewitter) vom Netz. Das Gerätkönnte sonst Schaden nehmen.4.Sollte versehentlich Flüssigkeit in das Gerät gelangen, so ziehen sofort denNetzstecker. Anderenfalls besteht die Gefahr eines lebensgefährlichenelektrischen Schlags.5.Wartungs- und Reparaturarbeiten dürfen aus Sicherheitsgründen nur vonautorisierten Personen durchgeführt werden.6.Bei Wartungs- und Reparaturarbeiten müssen die Sicherheitsvorschriften derzuständigen Berufsverbände und Behörden unbedingt eingehalten werden.7.Bei Verletzungen unbedingt den Arzt aufsuchen und die gegebenenfalls diezuständigen Stellen benachrichtigen. Unterlassung kann zum Verlust derVersicherungsleistungen führen.Please read the following instructions seriously.1.Keep the equipment away from humidity.2.Before you connect the equipment to the power outlet, please check thevoltage of the power source.3.Disconnect the equipment from the voltage of the power source to preventpossible transient over voltage damage.4.Don’t pour any liquid to the equipment to avoid electrical shock.5.ONLY qualified service personnel for safety reason should open equipment.6.Don’t repair or adjust energized equipment alone under any circumstances.Someone capable of providing first aid must always be present for your safety7.Always obtain first aid or medical attention immediately after an injury. Neverneglect an injury, no matter how slight it seems.安全须知请仔细阅读以下说明。
1. 本设备勿置于潮湿处。
2. 连接至电源前，请先检查电压。
3. 当设备不用时，请将电源线拔除避免电压不稳而造成伤害。
4. 勿将任何液体溅入设备中，避免线路短路。
5. 基于安全理由，只有受到专业训练的从业人员，才可以打开本设备。
6. 请勿自行调整或修理已通电的设备，以确保您的安全。
7. 如不小心受伤，请立刻找急救人员给予您适当的救护，千万别因伤势轻微而忽略自己的伤势。
8. 仅适用于在海拔2000m 以下地区使用。
CAUTIONDanger of explosion if battery is incorrectly replacedReplace only with the equivalent type recommended by the manufacture.Dispose of used batteries according to the manufacturer’s instructions.Only use with power supply adapter model: WDS060240P (9A).Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Specifications are subject to change without notice.第1 章条形码机 (1)1-1. 全机器材 (1)1-2. 产品规格 (1)1-3. 通讯端口规格 (3)1-4. 条形码机各部位介绍 (5)第2 章条形码机标准配备安装说明 (7)2-1. 碳带安装 (7)2-2. 标签纸安装 (9)2-3. 纸滚动条心安装说明 (10)2-4. 吊牌安装说明 (11)2-5. 计算机连结 (12)2-6. 驱动程序安装方式 (13)第3 章条形码机选购装备 (15)3-1. 自动剥纸器安装方式 (15)3-2. 裁刀安装方式 (18)3-3. 乙太网路卡安装方式 (21)3-4. 无线网卡安装方式 (23)3-5. CF记忆卡及定时器转接卡安装 (27)3-6. CF记忆卡使用注意事项 (28)第4 章条码机设定 (29)4-1. FEED键操作 (29)4-2. LED讯息说明 (29)4-3. 标签纸自动侦测及定位 (30)4-4. 自我测试页 (31)4-5. 操作错误讯息 (32)第5 章保养维謢与调校 (33)5-1. 印表头保养与清洁 (33)5-2. 印表头平衡调校 (34)5-3. 打印线调整 (35)5-4. 裁刀卡纸排除 (35)5-5. 故障排除 (36)第1 章条形码机1-1. 全机器材打开包装箱后，请先清点所有器材，并检查是否有因运送所造成的损坏。