汽车抬升器操作说明书与配件清单

Operating Instructions & Parts Manual
Model Number
HW93657
HW93667
HW93660
HW93662
Service Jacks
HW93657/ HW93660HW93667/ HW93662
Capacity
4 Ton
4 Ton Air/ Manual
10 Ton
10 Ton
Air/ Manual
Made in
North America
Save These Instructions
For your safety read, understand, and follow the information provided with and on this jack. The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use. The owner and operator shall be aware that use and repair of this product may require special skills and knowledge. Instructions and safety information shall be conveyed in the operator's native language before use of this jack is authorized. If any doubt exists as to the safe and proper use of this jack, remove from service immediately.
Inspect before each use. Do not use if there are broken, bent, cracked, or damaged parts (including labels). Any jack that appears damaged in any way, operates abnormally, or is missing parts, shall be removed from service immediately. If the jack has been or is suspected to have been subjected to a shock load (a load dropped suddenly, unexpectedly upon it), immediately discontinue use until the jack has been checked by a Hein-Werner authorized service center. It is recom-mended that an annual inspection be done by qualified personnel. Labels and Operator's Manual are available from manufacturer.
PRODUCT DESCRIPTION
Hein-Werner Hydraulic Service Jacks are designed to lift, not sustain, rated capacity loads. They are designed to be used in conjunction with jack stands. Intended use: To lift one wheel or one axle of a vehicle for the purpose of service and/or repair of vehicle components. After lifting, loads must be immediately supported by appropriately rated jack stands. Check with vehicle owner's manual for proper lift points.
DO NOT USE TO DOLLY OR MOVE VEHICLE.
DO NOT USE FOR ANY PURPOSE OTHER THAN THOSE USES OUTLINED ABOVE !
SAFETY INSTRUCTIONS
BEFORE USE
1.Verify that the product and application are compatible, if in doubt call Hein-Werner technical service.
2.Read the operator's manual completely and familiarize yourself thoroughly with the product, its components and recognize
the potential hazards associated with its use before the use of this product.
3.Follow assembly instructions
4.Lower saddle fully.
5.Locate and remove the air vent screw.
6.Ensure the oil level is within ~ 3/16" from the inner cylinder as viewed from the air vent screw hole.
7.Reinstall the air vent screw.
8.Close release valve by turning the release knob clockwise until firm resistance is felt.
9.Ensure that the jack rolls freely.
10.Raise and lower the unloaded saddle through out the lift range before putting into service to ensure the pump and release
valve operate smoothly.
11. Replace worn or damaged parts and assemblies with Hein-Werner Replacement Parts only. (See Replacement Parts
Section). Lubricate as instructed in Maintenance Section.
•Study, understand, and follow all instructions
provided with and on this device before operating this
device.
•Do not exceed rated capacity.
•This is a lifting device only.
•After lifting, immediately transfer the load to
appropriately rated vehicle stands.
•Never work on, under, or around a load supported by
this device.
•Use only on hard, level surfaces capable of
sustaining rated capacity loads.
•Do not move or dolly loads with this device.
•Do not modify this device.
•Do not use adapters or accessories that are not
provided initially.
•Lift only on areas of the vehicle as specified by the
vehicle manufacturer.
•Failure to heed these markings may result in
personal injury and/or property damage.
ASSEMBLY
EQUIPMENT NEEDED FOR ASSEMBLY:
1.Needle nose locking pliers
2.Snap-ring pliers (for: HW93657 and HW93667 only)
3.15 /16“ wrench (for: HW93660 and HW93662 only)
4.Hammer
5.Tape measure
6.All necessary hardware is included and is assembled loosely onto the jack
ASSEMBLY INSTRUCTIONS:
1.Remove the service jack base and handle from the carton.
2.For HW93657and HW93667, see figure 1 to remove the retaining ring and the handle pivot pin from the jack base that
connects through the handle fork. For HW93660 and HW93662 (as shown in figure 2) remove the 5/16-18 bolts and the pin from the jack base that connects through the handle fork.
3.Remove the #6-32 screw and nut from the universal receptacle on top of the hydraulic unit.
4.Pull the universal assembly, located on the bottom of the handle, out a minimum of 1-3/4".
5.Clamp the needle nose locking pliers onto the rod so that the universal assembly will not retract back into the handle.
6.Slide the universal assembly into the handle socket so that it extends out the other side.
7.Push the pivot pin that was removed in step 2 back through the handle and handle socket (may have to gently tap the
pin with a hammer).
8.Align the pivot pin with the holes on the side plates that the pivot pin was removed from and tighten the 5/16"-18 bolts
into the pivot pin until secure. (for HW93660 and HW93662 only)
9.Connect the universal assembly to the universal receptacle rod using the #6-32 screw and nut from note 3 (finger
tighten only).
10. Remove the needle nose locking pliers.
11.Jack is now operational and ready for use.
Helpful hint:
If the jack cover is a hindrance, it can be removed by using a 1/8" punch and taping out the pivot pins (be sure to attach
the cover back to the jack after assembly is completed).
OPERATION
Lifting
1.Place the vehicle in the park gear.
2.Engage the emergency brake.
3. Chock the wheels securely to prevent inadvertent vehicle movement.
4.Locate and close the release valve by turning release knob clockwise, firmly.
5. Center jack saddle under lift point. Refer to the vehicle manufacturer owner's manual to locate approved lifting points on the vehicle.
6.Verify lift point then use handle pump to contact lift point. To lift, pump handle until load reaches desired height.
7.Transfer the load immediately to appropriately rated jack stands.
Lowering
1.Raise load high enough to clear the jack stands.
2.Remove jack stands, carefully. (always used in pairs).
3.Slowly turn the release knob counterclockwise, but no more than 1/2 turn. If the load fails to lower:e another jack to raise the vehicle high enough to reinstall jack stands.b.Remove the malfunctioning jack and then the jack stands.
c. Using the functioning jack, lower the load by turning the operating handle counterclockwise, but no more than 1/2 turn.4.Push saddle down to reduce ram exposure to rust and contamination after removing the jack from under the loa
d.
Figure 3 - HW93657/ HW93660 Nomenclature
Figure 4 - HW93667/ HW93662 Nomenclature
Lift Arm
Figure 1 - HW93657/ HW93667Figure 2 - HW93660/ HW93662
Air Hose
Saddle
Handle
Lift Arm
Handle Fork
Caster
Front Wheel
Release Knob
Saddle
Handle
Release Knob
Caster
Air Motor
Air Vent Screw
(on the power unit)
Air Vent Screw (on the power unit)Handle Fork
Lift Arm
MAINTENANCE
Important: Use only a good grade hydraulic jack oil. Avoid mixing different types of fluid and Never use brake fluid, turbine oil, transmission fluid, motor oil or glycerin. Improper fluid can cause failure of the jack and the potential for sudden and immediate loss of load. We recommend Hein-Werner hydraulic jack oil HW 93291.
Adding oil
1. Lower saddle fully.
2.Set jack in its upright, level position.
3. Locate and remove air vent screw.
4.Fill with oil until ~3/16" above the inner cylinder as seen from the air vent screw hole.
5.Reinstall the air vent screw.
Changing oil
For best performance and longest life, replace the complete hydraulic fluid at least once a year.
1. Lower saddle fully.
2. Remove the air vent screw.
y the jack on its side and drain the fluid into a suitable container.
Note: Dispose of hydraulic fluid in accordance with local regulations.
4.Fill with oil until ~3/16" above the inner cylinder as seen from the air vent screw hole.
5.Reinstall the air vent screw.
Lubrication
A periodic coating of light lubricating oil to pivot points, axles and hinges will help to prevent rust and assure
that wheels, castors and pump assemblies move freely.
Cleaning
Periodically check the pump piston and ram for signs of rust or corrosion. Clean as needed and wipe with an oily cloth. Note: Never use sandpaper or abrasive material on these surfaces!
Storage
Lower the saddle to its lowest position when not in use.
TROUBLESHOOTING
Model HW93657 Replacement Parts
Figure 5 - Parts Illustration for Model HW93657
Model HW93657 Replacement Parts (cont.) - Hydraulic Unit
Figure 6 - Parts Illustration for Model HW93657 (Hydraulic Unit)
Model HW93657 Replacement Parts List
Part# Description Qty.
200003h Gasket1 200472Screw2 201110Lockwasher4 201479Lockwasher2 201733Plug1
201779Lockwasher2 201784Lockwasher1 201808Rivet2 203198h Ball (7/32" O.D.)1 203199h Ball (1/4" O.D.)1 203200h Ball (9/32" O.D.)1 203201h Ball (5/16" O.D.)1 203205h Ball (7/16" O.D.)1 203299Jam Nut4 203313Jam Nut2 203332Nut1 203344Jam Nut2 204270Washer2 204277Washer1 204301Washer1
204303Washer1 204343Washer4 204372Washer1 204444Cotter Pin3 204461Cotter Pin1 204842h Copper Gasket1 209964Lockwasher2 210225Spacer1 210311Pipe Plug3 210411h Washer1 211341Rivet1 212227Release Valve1 213152h Packing Ring2 213171h Packing Ring2 214538Groove Pin4
214555h O-ring1 214699Bushing1 214700Handle Segment Assy.1 216645Pin1 216646Pump Pin1 218988Roll Pin1 219451Hex Nut2 220769Cross Pin1 221739h Poppet1 221740Ball Stop Plug(7/16" L)1Part# Description Qty.
221742Ball Stop Plug (3/4" L)1
221764h Ram Quad Ring1
221766Cylinder1
221770Low Pressure Pump1
221771h Washer1
221772h Quad ring1
221778Washer4
221781Handle and Cross Bar1
221798Retainer Ring4
221817Retainer Ring2
221823Parallel Link2
221825Parallel Link Pin1
221829Pin1
221937Turning Knob1
221938Roll Pin1
222095Release Stem Kit1
222098Speed Pump Assy.1
222201h Spring1
222257Plug Poppet Valve2
222533h Screen2
223166h Ram Screen1
226314Gland Nut1
226318Grease Fitting1
226319Bellcrank Pin1
226324Pressure Plug1
226325Pump Link2
226326Nut1
226327Slotted Tube1
226329Pin1
226331h Spring1
226353h Spring1
226366Hex Head Bolt1
226372Spring1
226615Front Wheel2
227395Plunger Assy.1
227397Release Link1
227399Extension Rod1
227436Turning Rod Assy.1
228257h U-cup1
228354Universal Assy.1
228875Spring1
228881Grip2
229392Serial Plate1
229748h Heel Plate3
229749Washer1
Part# Description Qty.
229750Ram 1
229751Pin 1
230583Ram Assy.1
231316Vent Valve Assy.1
231583Rear Caster2
231638Filler Screw1
231710Oil Tank1
232968h Back-up Washer1
232969h U-cup1
232970Pressure Pump1
232971Pressure Pump Kit1
233798Tank Nut1
233880Tank Nut and Quad Ring1
233917h Plastic Spring1
233921Release Stem1
234976Cap Housing1
241885Bellcrank1
241887Handle Socket1
241889Liftcap1
241893Sideplate Assy1
241894Sideplate Assy1
241895Hydraulic Unit Cover1
241907Repair Kit (Hyd. Unit)-
241956Fulcrum Pin1
241983Sideplate Tie Rod2
241985Support Rod1
241986Front Axle1
241987Retainer ring2
241988Handle Pivot Pin1
241989Extension Spring2
241990Handle Assy.1
241991Hydraulic Unit Casting1
241993Hydraulic Unit Assy.1
HW93657-K0 Label Kit (not shown)
HW93657-M0 Manual
h Included in Repair Kit 241907
Model HW93660 Replacement Parts
Figure 7 - Parts Illustration for Model HW93660
Model HW93660 Replacement Parts (cont.) - Hydraulic Unit
Figure 8 - Parts Illustration for Model HW93660 (Hydraulic Unit)
Model HW93660 Replacement Parts List
Part# Description Qty. 200003Gasket1 200472Bolt2 201110Lockwasher4 201115Lockwasher2 201481Lockwasher2 201733Expansion Plug1 201784Lockwasher1 201789Lockwasher2 203198h Ball1 203199h Ball1 203200h Ball1 203201h Ball1 203207h Ball1 203272Nut2 203297Nut2 203299Nut2 203323Nut2 203332Nut1 203344Nut2 204270Washer2 204277Washer1 204301Washer1 204303Washer1 204372Washer1 204444Cotter Pin4 204461Cotter Pin1 204842h Gasket1 207169Nut2 209964Lockwasher2 210225Spacer1 210311Pipe Plug3 210411h Washer1 211341Rivet1 212227Release Valve1 212689Bolt2 213152h Packing Ring2 213171h Packing Ring2 214538Groove Pin4 214555h O-ring1 214699Bushing1 214700Handle Segment1
& Bushing
216645Pin1 216646Pin1 217653Roll Pin2 218988Roll Pin1 218991Roll Pin1Part# Description Qty..
220769Cross Pin1
221739Poppet1
221742Ball Stop Plug1
221770Speed Pump1
221771h Back-up Washer1
221772Quad Ring1
221781Handle & Cross Bar1
221809Handle Grip2
221937Release Knob1
221938Roll Pin1
222095Release Stem Assy.1
222098Speed Pump Assy.1
222201h Spring1
222257Plug1
222533h Screen2
223166h Screen1
224253Cover1
226271Fulcrum Pin1
226314Gland Nut1
226318Grease Fitting5
226325Pump Link2
226326Gland Nut1
226331Spring1
226353h Spring1
226366Bolt1
226372Plunger Spring1
227397Link1
227436Turning Rod Assy.1
228875Spring1
229887h O-ring1
229888h O-ring1
229889h O-ring1
229896Ram & Cylinder Assy.1
229898Cylinder1
229899h U-cup Packing1
229900h Back-up Washer1
229902Cross Pin1
229903Pin1
229904Plug1
229905Plug1
229908Spacer1
229909Slotted Tube1
229910Retaining Ring2
229911Retaining Ring2
229912Washer4
229913Bell Crank1
229915Front Wheel2
Part# Description Qty.
229927Cap Housing1
229929Bearing1
229932Spring2
229933Plate2
229934Pin1
229937Caster2
229938Pin1
229939Front Axle1
229946Pin1
229947Retaining Ring4
229949Handle Socket1
229951Extension rod1
229952Plunger Assy.1
229956Heel Plate1
230006Bumper Pin1
230407Universal Assy.1
231316Filler Plug & Gasket Assy.1
231419Fulcrum Pin1
231420Bolt2
231430Parallel Link2
231474Bell Crank & Fittings1
231638Filler Plug & Vent Valve1
231717Base1
231718Oil Tank1
231945Ram Assy.1
231962Handle Assy.1
231963Front Wheel Assy.2
232619Lifting Cap1
232620Swivel Pin1
232968h Back-up Washer1
232969h U-cup Packing1
232970Pressure Pump1
232971Pressure Pump &1
Gland Packing Assy.
233917Plastic Spring1
233921Release Stem1
240616Repair Kit (Hyd. Unit)-
241482Tank Nut1
241483h Seal1
241551Hydraulic Unit Assy.1
244317Pin1
245119Ram1
HW93660-K0 Label Kit (not shown)
HW93657-M0 Manual
h Included in Repair Kit 240616
Model HW93662 Replacement Parts
Figure 9 - Parts Illustration for Model HW93662
Model HW93662 Replacement Parts (cont.) - Hyd. Unit
Figure 10 - Parts Illustration for Model HW93662 (Hydraulic Unit)
Model HW93662 Replacement Parts (cont.) - Air Hyd. Pump
Figure 11 - Parts Illustration for Model HW93662 (Air Hyd. Pump)
200003Gasket1 200472Bolt2 201110Lockwasher4 201115Lockwasher2 201481Lockwasher2
201733Expansion Plug1 201784Lockwasher1 201789Lockwasher2 203198h Ball (7/32" O.D.)1 203199h Ball (1/4" O.D.)1
203200h Ball (9/32" O.D.)1 203201h Ball (5/16" O.D.)1 203202Ball (11/32" O.D.)1 203207h Ball1 203272Nut2
203297Nut2 203299Nut2 203301Jam Nut1 203323Nut2 203332Nut1203344Nut2 204270Washer2 204277Washer1 204301Washer1 204303Washer1
204372Washer1 204444Cotter Pin4 204461Cotter Pin1 204842h Gasket1 207169Nut2
209964Lockwasher2 210225Spacer1 210311Pipe Plug3 210411h Washer1 211341Rivet1
212227Release Valve1 212689Bolt2 213152h Packing Ring2 213171h Packing Ring2 214538Groove Pin4
Model HW93662 Replacement Parts List
Part# Description Qty
214555h O-ring1
214699Bushing1
214700Handle Segment &1
Bushing
216645Pin1
216646Pin1
217653Roll Pin2
218988Roll Pin1
218991Roll Pin1
219861O-ring1
220769Coss Pin1
221013#U-cup Packing1
221739Poppet1
221742Ball Stop Plug1
221770Speed Pump1
221771h Back-up Washer1
221772Quad Ring1
221809Handle Grip2
221820Retaining Ring2
221937Release Knob1
Part# Description Qty Part# Description Qty
Model HW93662 Replacement Parts List (Cont.)
221938Roll Pin1 222095Release Stem Assy.1 222098Speed Pump Assy.1 222201h Spring1 222202Elbow1
222257Plug1 222288#O-ring1 222533h Screen2 223166h Screen1 223172Hose Clip1
223173Return Spring1 223176Cylinder, Air1 223179Hose Clip2 223180Air Valve1 223183Plug1
223184Spring1 223187#Valve & Plunger1 223194Spring & Cushion1 223203Trip Washer2 223220Handle & Cross Bar1 223678Pump Packing &1
Piston
223680Screen1 224021Hose, Air1 224081Screw2 224156Spring1 224469Washer1 225371Rubber Cushion1 225384Trip Spring1 225906Bracket, Speed pak1
226153Spring1 226271Fulcrum Pin1 226314Gland Nut1 226318Grease Fitting5 226325Pump Link2 226326Gland Nut1 226331Spring1 226353h Spring1 226366Bolt1 226372Plunger Spring1 226373Adjusting Screw1 226401Spring1 226450End Block1 226451Set Screw2 226483Pipe Nipple1227397Link1
227436Turning Rod Assy.1
227713Lockwasher1
228235Cotter Pin1
228813Washer1
228814#Gland Nut1
228815#U-cup Packing1
228816#Washer1
228875Spring1
229754Pin1
229887h O-ring1
229888h O-ring1
229889h O-ring1
229896Ram & Cylinder Assy.1
229898Cylinder1
229899h U-cup Packing1
229900h Back-up Washer1
229902Cross Pin1
229903Pin1
229904Plug1
229905Plug1
229908Spacer1
229909Slotted Tube1
229910Retaining Ring2
229911Retaining Ring2
229912Washer4
229913Bell Crank1
229915Front Wheel2
229927Cap Housing1
229929Bearing1
229932Spring2
229933Plate2
229934Pin1
229938Pin1
229939Front Axle1
229946Pin1
229947Retaining Ring4
229949Handle Socket1
229951Extension Rod1
229952Plunger Assy.1
229956Heel Plate1
229999Air Hyd. Pump Assy.1
230000Pump Cylinder1
230003Back-up Washer1
230005Gland Nut1
230006Bumper Pin1
230007U-bolt1
230008Bracket1
230010Caster2
230011Spacer1
230407Universal Assy.1
231316Filler Plug &1
Gasket Assy.
231347Piston & Roll Pin1
231419Fulcrum Pin1
231420Bolt2
231430Parallel Link2
231474Bell Crank & Fittings1
231572Cylinder Cap1
231604Piston Assy.1
231619Rod, Pump1
231638Filler plug & Vent Valve1
231717Base1
231718Oil Tank1
231945Ram Assy.1
231963Front Wheel Assy.2
231990Handle Assy.1
232619Lifting Cap1
232620Swivel Pin1
232968h Back-up Washer1
232969h U-cup Packing1
232970Pressure Pump1
232971Pressure Pump &1
Gland Packing Assy.
233110Pump U-cup1
233622Screw4
233897Ring, Sealing1
233917Plastic Spring1
233921Release Stem1
240564Repair Kit (Air Pump)-
240616Repair Kit (Hyd. Unit)-
241482Tank Nut1
241483h Seal1
241552Hydraulic Unit Assy.1
244253Cover1
244317Pin1
245119Ram1
HW93662-K0 Label Kit (not shown)
HW93657-M0 Manual
h Included in Repair Kit 240616
# Included in Repair Kit 240564
Part# Description Qty Part# Description Qty Part# Description Qty
Model HW93667 Replacement Part
Figure 12 - Parts Illustration for Model HW93667
Model HW93667 Replacement Parts (cont.) - Hyd. Unit
Figure 13 - Parts Illustration for Model HW93667 (Hyd. Unit)
Model HW93667 Replacement Parts (cont.) - Air Hyd. Pump
Figure 14 - Parts Illustration for Model HW93667 (Air Hyd. Pump)
Model HW93667 Replacement Parts List
Part# Description Qty Part# Description Qty Part# Description Qty
200003h Gasket1 200472Screw2 201110Lockwasher4 201479Lockwasher2 201733Plug1
201779Lockwasher2 201784Lockwasher1 201808Rivet2 203198h Ball (7/32" O.D.)1 203199h Ball (1/4" O.D.)1
203200h Ball (9/32" O.D.)1 203201h Ball (5/16" O.D.)1 203202Ball (11/32" O.D.)1 203205h Ball (7/16" O.D.)1 203299Jam Nut4
203313Jam Nut2 203332Nut1 203344Jam Nut2 204270Washer2 204277Washer1204301Washer1
204303Washer1
204343Washer4
204372Washer1
204444Cotter Pin3
204461Cotter Pin1
204842h Copper Gasket1
209964Lockwasher2
210225Spacer1
210311Pipe Plug4
210411h Washer1
211341Rivet1
212227Release Valve1
213152h Packing Ring2
213171h Packing Ring2
213639Bolt1
214538Groove Pin4
214555h O-ring1
214699Bushing1
214700Handle segment Assy.1
216645Pin1
216646Pump Pin1
218988Roll Pin1
219451Hex Nut2
220769Cross Pin1
221013#U-cup Packing1
221377Roll Pin1
221739h Poppet1
221740Ball Stop Plug (7/16" L)1
221742Ball Stop Plug (3/4" L)1
221764h Ram Quad Ring1
221766Cylinder1
221770Low Pressure Pump1
221771h Washer1
221772h Quad ring1
221778Washer2
221798Retainer Ring4
221817Retainer Ring2
221820Retaining Ring1
221823Parallel Link2
Model HW93667 Replacement Parts List (cont.)
Part# Description Qty Part# Description Qty Part# Description Qty
221825Parallel Link Pin1 221829Pin1 221937Turning Knob1 221938Roll Pin1 222088Screen Assembly1
222095Release Stem Kit1 222098Speed Pump Assy.1 222201h Spring1 222202Elbow1 222257Plug Poppet Valve2
222288#O-ring1 222533h Screen2 223166h Ram Screen1 223172Hose Clip1 223173Return Spring1
223179Hose Clip2 223180Air Valve1 223183Plug1 223184spring1 223187#Valve & Plunger1 223203Trip Washer2 223213Gland Nut1 223220Handle & Cross Bar1 223678Pump Packing &1
Piston
223680Screen1 224034Air Cylinder1 224038Pump Rod1 224081Screw3 224156Spring1 224344Ball Stop Plug1 224414Retaining Ring1 224469Washer1 225371Rubber Cushion1 225384Trip Spring1 225906Bracket, Speed pak1 226019Lock Nut4 226153Spring1 226314Gland Nut1 226318Grease fitting1
226319Bellcrank Pin1 226324Pressure Plug1 226325Pump Link2 226326Nut1 226327Slotted tube1226329Pin1
226331h Spring1
226353h Spring1
226366Hex Head Bolt1
226372Spring1
226373Adjusting Screw1
226450End block1
226451Set Screw2
226483Pipe Nipple1
226615Front Wheel2
227052Washer1
227395Plunger Assy.1
227397Release Link1
227399Extension Rod1
227436Turning Rod Assy.1
228235Cotter Pin1
228257h U-cup1
228354Universal Linkage1
228813Washer1
228814#Glant Nut1
228815#u-cup Packing1
228816#Washer1
228875Spring1
228881Grip2
229392Serial plate1
229748h Heel Plate3
229749Washer1
229750Ram1
229751Pin1
229754Extension tube1
230003h Back-up Washer1
230007U-bolt1
230430Air Hose Assy.1
230583Ram Assy.1
230753Suction Tube1
231316Vent Valve Assy.1
231572Cylinder Cap1
231583Rear Caster2
231638Filler Screw1
231710Oil Tank1
232968h Back-up Washer1
232969h U-cup1
232970Pressure Pump1
232971Pressure Pump Kit1
233110Pump U-cup1
233798Tank Nut1
233880Tank Nut and Quad1
Ring
233917h Plastic Spring1
233921Release stem1
234976Cap Housing1
236684Piston1
236685Sealing ring1
240564Repair Kit (Hyd. Pump) 1
241780Handle1
241885Bellcrank1
241887Handle Socket1
241889Liftcap1
241894Sideplate Assy1
241895Hydraulic Unit Cover1
241907Repair Kit (Hyd. Unit)-
241955Sideplate Assy1
241956Fulcrum Pin1
241983Sideplate Tie Rod2
241985Support Rod1
241986Front Axle1
241987Retainer ring4
241988Handle Pivot Pin1
241989Extension spring2
241992Hydraulic Unit Casting1
241994Hydraulic Unit Assy.1
242160Air Hyd. Pump Assy.1
242161Pump Cylinder1
243098U-bolt1
243101Sleeve1
HW93667-K0 Label Kit (not shown)
HW93657-M0 Manual
h Included in Repair Kit 241907
# Included in Repair Kit 240564。