VJ0805Q1R8FFAAT中文资料
红色贴片式发光二极管XL-2012SURC产品说明书
产品承认书产品名称：0805-T0.8红色贴片式发光二极管产品型号：XL-2012SURC客户名称：客户料号：承认日期：深圳市成兴光电子科技有限公司制定审核核准客户承认栏确认审核核准一、产品描述：●外观尺寸(L/W/H): 2.0x1.25x0.8mm●颜色:高亮度红色●胶体:透明胶体●EIA规范标准包装●环保产品，符合ROHS要求●适用于自动贴片机●适用于回流焊制程二、外形尺寸及建议焊盘尺寸：C athode A nodeG reen m ark建议焊盘尺寸备注：1.单位:毫米（mm）2.公差：如无特别标注则为±0.10mm三、建议焊接温度曲线：有铅制程无铅制程四、最大绝对额定值（Ta=25℃）：参数符号最大额定值单位消耗功率Pd55mW最大脉冲电流(1/10占空比,0.1ms脉宽)I FP100mA正向直流工作电流I F25mA 反向电压V R5V 工作环境温度Topr-30°C~+85°C存储环境温度Tstg-40°C~+90°C焊接条件Tsol 回流焊:260°C,10s 手动焊:300°C,3s五、光电参数（Ta=25℃）：参数符号最小值代表值最大值单位测试条件光强IV 38---75mcd IF=5mA 半光强视角2θ1/2---120---deg IF=5mA 主波长λD 617---623nm IF=5mA 正向电压VF 1.85--- 2.1V IF=5mA 反向电流IR------1uAVR=5V亮度分档:代码最小值最大值单位测试条件M33845mcdIF=5mAM44560M56075电压分档:代码最小值最大值单位测试条件V1 1.85 1.9V IF=5mAV2 1.9 1.95V3 1.95 2.0V4 2.0 2.05V52.052.1波长分档:代码最小值最大值单位测试条件R1617619nmIF=5mAR2619621R3621623六、光电参数代表值特征曲线：φ60七、标签标识：CAT ：光强（mcd ）HUE ：波长（nm ）REF ：电压（V ）误差范围a.Luminous Intensity:±15%b.HUE:±1nmc.Forward Voltage:±0.1V八、包装载带与圆盘尺寸：φ13.0AU ser Feed D irectionAA-A剖面图备注：1.单位:毫米（mm）2.公差：如无特别标注则为±0.15mm九、圆盘及载带卷出方向及空穴规格：尾端至少160mm盖带和空壳载带的组合开始端装有零件部分至少160mm盖带和至少160mm独立盖带或空壳载带的组合盖带与空壳载带的组合十、内包装及外包装：内标签圆盘干燥剂防潮防静电袋5cartons/box外标签抽真空、热封10bags/carton十一、信赖性实验：测试项目测试条件测试次数参考标准失效判定标准失效LED数量（PCS）防潮等级1.回流焊最高温度=260℃,10秒，2次回流焊；2.回流焊之前存储条件：30℃，相对湿度=70%，168H；-JEITAED-4701300301﹟10/22焊接信赖性（无铅回流焊）回流焊最高温度=245±5℃，5秒（无铅回流焊）-JEITAED-4701303303A﹟20/22冷热循环-40℃30分钟~25℃5分钟~100℃30分钟~25℃5分钟300个循环JESD22-A104﹟10/22冷热冲击-35℃15分钟转换时间3分钟85℃15分钟300个循环JESD22-A106﹟10/22高温存储Ta=100℃1000小时JESD22-A103﹟10/22低温存储Ta=-40℃1000小时JESD22-A119﹟10/22常温老化Ta=25℃IF=20mA1000小时JESD22-A108﹟10/22（2）失效标准标准﹟项目测试条件失效标准﹟1正向电压(V F)I F=20mA＞U.S.L*1.1光强（IV）I F=20mA＜L.S.L*0.7反向电流(I R)V R=5V＞U.S.L*2.0﹟2焊接可靠性/锡膏覆盖焊盘比例小于95%★U.S.L:规格上限L.S.L:规格下限十二、使用注意事项：◆使用：1.过高的温度会影响LED的亮度以及其他性能，所以为使LED有较好的性能表现，应将LED远离热源。
Green Source 1.6 mm x 0.8 mm SMD LED 产品说明书
DESCRIPTIONSThe Green source color devices are made withAlGaInP on GaAs substrate Light Emitting Diode Electrostatic discharge and power surge could damage the LEDsIt is recommended to use a wrist band oranti-electrostatic glove when handling the LEDs All devices, equipments and machineries must be electrically groundedFEATURES1.6 mm x 0.8 mm SMD LED, 0.2 mm thickness Low power consumption Wide viewing angleCompatible with automatic placement equipment Ideal for backlight and indicator Package: 4000 pcs / reel Moisture sensitivity level: 3RoHS compliantAPPLICATIONSBacklightStatus indicatorHome and smart appliances Wearable and portable devicesHealthcare applicationsATTENTIONObserve precautions for handlingelectrostatic discharge sensitive devicesPACKAGE DIMENSIONSSELECTION GUIDENotes:1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.2. Luminous intensity / luminous flux: +/-15%.3. Luminous intensity value is traceable to CIE127-2007 standards.KPG1-1608CGC-TT1.6 x 0.8 x 0.2 mm (0603) SMD Chip LED LampRECOMMENDED SOLDERING PATTERN(units : mm; tolerance : ± 0.1)Notes:1. All dimensions are in millimeters (inches).2. Tolerance is ±0.1(0.004") unless otherwise noted.3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.4. The device has a single mounting surface. The device must be mounted according to the specifications.Part NumberEmitting Color (Material)Lens TypeIv (mcd) @ 20mA [2] Viewing Angle [1]Min.Typ.2θ1/2KPG1-1608CGC-TT Water Clear ■Green (AlGaInP) 12 35 120°Ki n gABSOLUTE MAXIMUM RATINGS at T A =25°CELECTRICAL / OPTICAL CHARACTERISTICS at T A =25°CNotes:1. 1/10 Duty Cycle, 0.1ms Pulse Width.2. R t h JA ,R t h JS Results from mounting on PC board FR4 (pad size ≥ 16 mm 2 per pad).3. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.ParameterSymbolUnit Power Dissipation P D 60 mW Reverse Voltage V R 5 V Junction Temperature T j 115 °C Operating Temperature T op -40 to +85 °C Storage Temperature T stg -40 to +85°C DC Forward Current I F 25 mA Peak Forward CurrentI FM [1]120 mA Thermal Resistance (Junction / Ambient) R th JA [2] 700 °C/W Thermal Resistance (Junction / Solder point)R th JS [2]600°C/WValue Electrostatic Discharge Threshold (HBM) -3000 V ParameterSymbolEmitting ColorValue UnitTyp. Max. Wavelength at Peak Emission I F = 20mA λpeak Green 572 - nm Dominant Wavelength I F = 20mA λdom [1] Green 571-nmSpectral Bandwidth at 50% Φ REL MAX I F = 20mA ΔλGreen20 - nmCapacitanceC Green 15 - pFForward Voltage I F = 20mA V F [2]Green 2.0 2.4 VReverse Current (V R = 5V) I RGreen- 10 uATemperature Coefficient of λpeak I F = 20mA, -10°C ≤ T ≤ 85°C TC λpeakGreen0.12 - nm/°CTemperature Coefficient of λdom I F = 20mA, -10°C ≤ T ≤ 85°C TC λdomGreen0.08 - nm/°CTemperature Coefficient of V F I F = 20mA, -10°C ≤ T ≤ 85°CTC VGreen-1.9 - mV/°CNotes:1. The dominant wavelength (λd) above is the setup value of the sorting machine. (Tolerance λd : ±1nm. )2. Forward voltage: ±0.1V.3. Wavelength value is traceable to CIE127-2007 standards.4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure.Ki n g b r i g h tTECHNICAL DATAGREENTAPE SPECIFICATIONS (units : mm) REFLOW SOLDERING PROFILE for LEAD-FREE SMD PROCESSNotes:1. Don't cause stress to the LEDs while it is exposed to high temperature.2. The maximum number of reflow soldering passes is 2 times.3. Reflow soldering is recommended. Other soldering methods are not recommended as they mightcause damage to the product.REEL DIMENSION (units : mm)tPACKING & LABEL SPECIFICATIONSPRECAUTIONARY NOTES1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer tothe latest datasheet for the updated specifications.3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. Ifcustomer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threateningliabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance.5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.6. All design applications should refer to Kingbright application notes available at /application_notesKi n gb ri g ht。
VJ0805Q1R8CFBAT中文资料
GENERAL SPECIFICATIONS
NOTE: Electrical characteristics @ + 25°C unless otherwise specified. Capacitance Range: 1.0pF to 680pF. Temperature Coefficient of Capacitance (TCC): 0 ± 30PPM/°C from - 55°C to + 125°C. Dissipation Factor (DF): 0.1% maximum @ 1.0 Vrms and 1kHz for values > 1000pF. 0.1% maximum @ 1.0 Vrms at 1MHz for values ≤ 1000pF. Insulation Resistance (IR): @ + 25°C and rated voltage 100,000 Megohms minimum or 1000 ohm-farads, whichever is less. @ + 125°C and rated voltage 10,000 Megohms minimum or 100 ohm-farads, whichever is less. Dielectric Withstanding Voltage (DWV): 250% of rated voltage for 5 ± 1 seconds, 50 milliamps current maximum.
RESONANT FREQUENCY (GHz)
TEMPERATURE COEFFICIENT OF CAPACITANCE 2.0 1.5 1.0 0.5 0.0 - 0.5 - 1.0 - 1.5 - 2.0 -75 -50 -25 0 25 50 75 100 125 TEMPERATURE °C Q vs FREQUENCY - VJ0805, 50V 10000 10pF 1000 1 HIGH Q SERIES RESONANT FREQUENCY - HIGH Q 10
LED洗墙灯
序号参考图片品名编号产品规格工作电压尺寸(mm)发光芯片发光颜色材质发光角度工作电压尺寸(mm)发光芯片发光颜色材质发光角度工作电压2JC-XQ-02集 臣 照 明 电 器Set Chen Lighting Co., Ltd.厂址：中国广东-中山市古镇镇曹二工业区曹兴东路32号集臣公司联系电话：-86-0760-******** -86-0760-********公司传真：-86-0760-********官方网站： 公司邮箱：ledwsz@ 邮箱：zrzled@服务热线：-86-0760-********钟如珍(业务经理):136********/189******** 商务QQ:848008886/1246444618洗墙灯（报1JC-XQ-01发光芯片发光颜色材质发光角度工作电压尺寸(mm)发光芯片发光颜色材质发光角度工作电压尺寸(mm)发光芯片发光颜色材质发光角度工作电压尺寸(mm)发光芯片发光颜色材质发光角度6JC-XQ-065JC-XQ-054JC-XQ-043JC-XQ-03尺寸(mm)发光芯片发光颜色材质发光角度工作电压尺寸(mm)发光芯片发光颜色材质发光角度工作电压尺寸(mm)发光芯片发光颜色材质发光角度工作电压尺寸(mm)发光芯片发光颜色材质10JC-XQ-109JC-XQ-098JC-XQ-087JC-XQ-07抄：集臣市场部送：总经理、财务部、业务部、售后部、及各省经销商本价格表解释权归中山市集臣照明电器有限公司所有报价员：唐雪 制表人：肖陈娟注：1.以上单价供参考，以当天报价为准。
2.以上报价不含税金、托运费、安装费用。
3.以上报价发光颜色均为正白/暖白光，如需要其它发光颜色，价格另异。
4.以上产品电压、发光颜色可依据客户要求生产（选用单颗七彩每颗珠加10元）。
5.付款方式：现金交易。
6.售后服务以上产品，实行一年保修，终身维护的售后政策。
从产品运抵之日起计算，一年内产生的非人后问题产生的费用由厂家承担。
佛山国星光电股份有限公司产品说明书：NCD0805Y1型号的LED二极管
佛山市国星光电股份有限公司FOSHAN NATIONSTAR OPTOELECTRONICS CO.,LTD顾客名称Customer 产品名称ProductChip LED顾客型号Customer Type 产品型号TypeNCD0805Y1顾客部品号Customer No.版本号Version NOA版研发中心Research&Development Center客户（加盖公章）Customer（Stamp）制定DRAW 审核CHECK批准APPROVE确认CONFIRM陆紫珊李友民朱明军发放日期(Release Date)：2019-10-30产品规格书地址：广东省佛山市禅城区华宝南路18号Add:NO.18South Huabao Rd,Foshan,Guangdong,China电话（Tel）：*************传真（Fax）：*************邮编（Zip）：528000邮箱（Email）：********************** SPECIFICATION保存期限：长期NCD0805Y1Chip Light Emitting Diode技术数据表Technical Data Sheet本产品主要作为信号指示及照明的电子元件广泛应用于各类使用表面贴装结构的电子产品中，如家用电器的开关指示灯、手机键盘灯、汽车仪表盘指示灯等。
This product is generally used as indicator and luminance for surface mounted electronic equipment,such as*The specifications of the product may be modified for improvement without notice.外形尺寸Outline Dimension极性Polarity-+推荐焊盘尺寸Recommended Soldering PadElectro-Optical Characteristics(1)✧极限参数（温度=25℃）Absolute Maximum Ratings(Temperature=25°C)*注：脉冲宽度≤0.1ms，占空比≤1/10*Note:Pulse Width≤0.1ms,Duty≤1/10✧光电参数（温度=25℃）Electro-Optical Characteristics(Temperature=25°C)*注1：光强偏差±15%；压降偏差±0.1V；(X,Y)坐标偏差±0.01；单色光波长偏差±1nm。
0805白色贴片LED灯珠规格书
第8页共8页
第4页共8页
七、可靠性试验：
产品名称：0805 片式发光二极管 产品型号：LX17-21SUWC/A16
序号
试验项目
试验条件
数量
判据
1 可焊性试验
T=300℃ T=3.5±0.5sec.
0/15
TA=－40℃，TB=＋85℃ 循环 5 次，
温度快速变化
Hale Waihona Puke 暴露时间：10min 转移时间：（2~3）
2 继 之 以 循 环 湿 热 min
单位
正向电流
IF
*
正向脉冲电流 IFP
25
mA
100
mA
反向电压
VR
5
V
工作温度
TOPR
-30
+85
℃
贮存温度
TSTG
-40
+85
℃
功耗
PD
75
mW
焊接条件 Tsol
回流焊：260℃，10S；手动焊：300℃，3S
*注：脉冲宽度 10ms，占空比 1/10。
四、 光电参数（TA=25℃）：
参数名称 条件
一、 特点：
l 管芯材料： White白色
l 黄色平面胶体
l 2.0mm×1.25mm×1.1mm片式发光二极管
l 光强高,功耗低,可靠性高,寿命长
l 符合欧盟公布的 RoHS指令
二、 用途： 移动电话、LCD背光源、汽车仪表照明以及用表面贴
装结构的电子产品等。
三、 极限参数（TA=25℃）：
参数
最小值 最大值
23mint2555rh9095环48h恢复时间2耐焊接热试验红外回流焊法见图3015电耐久性试验if25mat1000h015高温贮存试验t85t1000h015循环湿热t2555rh9095失效判断标准测试项目符号测试条件失效判断标准正向电压vfif20mau11反向电流光强ivif20mas07产品名称
K6X0808C1D-BF55中文资料
Document Title32Kx8 bit Low Power CMOS Static RAM Revision HistoryRevision No.0.01.02.03.0RemarkPreliminaryFinalFinalFinal HistoryInitial draftFinalized- Changed I CC from 10mA to 5mA- Changed I CC1 from 8mA to 7mA- Changed I CC2 from 35mA to 25mA- Changed I SB from 3mA to 0.4mA- Changed I DR for K6X0808C1D-F 15µA to 10µA- Changed I DR for K6X0808C1D-Q 25µA to 20µA- Errata correctionRevised- Changed I SB1of Automotive product from 25µA to 30µA- Deleted 55ns Automotive productRevised- Changed I SB1of Automotive product from 30µA to 50µA- Changed I DR of Automotive product from 20µA to 25µA- Added Lead Free ProductsDraft DataOctober 09, 2002December 16, 2003July 15, 2004March 27, 2005The attached datasheets are provided by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserves the right to change the specifications and products. SAMSUNG Electronics will answer to your questions. If you have any questions, please contact the SAMSUNG branch offices.32Kx8 bit Low Power full CMOS Static RAMGENERAL DESCRIPTIONThe K6X0808C1D families are fabricated by SAMSUNG ′s advanced CMOS process technology. The families support verious operating temperature ranges and have various pack-age types for user flexibility of system design. The families also support low data retention voltage for battery back-up operation with low data retention current.FEATURES• Process Technology: Full CMOS • Organization: 32K x 8• Power Supply Voltage: 4.5~5.5V• Low Data Retention Voltage: 2V(Min)• Three state output and TTL Compatible • Package Type: 28-DIP-600B, 28-SOP-450,28-TSOP1-0813.4F/RPRODUCT FAMILY1. The parameters are tested with 50pF test loadProduct Family Operating Temperature Vcc RangeSpeedPower DissipationPKG TypeStandby (I SB1, Max)Operating (I CC2, Max)K6X0808C1D-F Industrial(-40~85°C)4.5~5.5V551)/70ns 15µA25mA28-DIP-600B, 28-SOP-450,28-TSOP1-0813.4F/R K6X0808C1D-QAutomotive(-40~125°C)70ns50µA28-SOP-450, 28-TSOP1-0813.4FSAMSUNG ELECTRONICS CO., LTD. reserves the right to change products and specifications without notice.PIN DESCRIPTIONPin NameFunctionPin NameFunctionCS Chip Select Input I/O 1~I/O 8Data Inputs/OutputsOE Output Enable Input Vcc Power WE Write Enable Input Vss Ground A 0~A 14Address InputsNCNo connectA14A12A7A6A5A4A3A2A1A0I/O1I/O2I/O3VSSVCC WE A13A8A9A11OE A10CS I/O8I/O7I/O6I/O5I/O428-DIP 28-SOP15162827262524232221201918171234567891011121314A11A9A8A13WE VCC A3A14A12A7A6A5A4A10CS I/O8I/O7I/O6I/O5I/O4VSS I/O3I/O2I/O1A0A1A228-TSOP Type1 - Forward12345678910111213142726282524232221201918171615OE 28-TSOP A11A9A8A13WE VCC A3A14A12A7A6A5A4A10I/O8I/O7I/O6I/O5I/O4VSS I/O3I/O2I/O1A0A1A212345678910111213142726282524232221201918171615OEType1 - ReverseFUNCTIONAL BLOCK DIAGRAMPRODUCT LIST1.Lead Free ProductsIndustrial Temp. Products(-40~85°C)Automotive Temp. Products(-40~125°C)Part Name FunctionPart Name FunctionK6X0808C1D-DF55K6X0808C1D-DF70K6X0808C1D-GF55K6X0808C1D-GF70K6X0808C1D-BF551)K6X0808C1D-BF701)K6X0808C1D-TF55K6X0808C1D-TF70K6X0808C1D-LF551)K6X0808C1D-LF701)K6X0808C1D-RF55K6X0808C1D-RF7028-DIP , 55ns, LL Pwr 28-DIP , 70ns, LL Pwr 28-SOP , 55ns, LL Pwr 28-SOP , 70ns, LL Pwr 28-SOP , 55ns, LL Pwr, LF 28-SOP , 70ns, LL Pwr, LF 28-TSOP-F, 55ns, LL Pwr 28-TSOP-F, 70ns, LL Pwr 28-TSOP-F, 55ns, LL Pwr, LF 28-TSOP-F, 70ns, LL Pwr, LF 28-TSOP-R, 55ns, LL Pwr 28-TSOP-R, 70ns, LL PwrK6X0808C1D-GQ70K6X0808C1D-BQ701)K6X0808C1D-TQ70K6X0808C1D-LQ701)28-SOP , 70ns, L Pwr 28-SOP , 70ns, L Pwr, LF 28-TSOP-F, 70ns, L Pwr 28-TSOP-F, 70ns, L Pwr, LFABSOLUTE MAXIMUM RATINGS 1)1. Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. Functional operation should be restricted to recommended operating condition. Exposure to absolute maximum rating conditions for extended periods may affect reliability.ItemSymbol RatingsUnit RemarkVoltage on any pin relative to Vss V IN ,V OUT -0.5 to V CC+0.5V(Max. 7.0V)V -Voltage on Vcc supply relative to Vss V CC -0.3 to 7.0V -Power Dissipation P D 1.0W -Storage temperature T STG -65 to 150°C -Operating TemperatureT A-40 to 85°C K6X0808C1D-F -40 to 125°CK6X0808C1D-QFUNCTIONAL DESCRIPTION1. X means don ′t care (Must be in high or low states)CS OE WE I/O Mode Power H X 1)X 1)High-Z Deselected Standby L H H High-Z Output DisabledActive L L H Dout Read Active LX 1)LDinWriteActiveRECOMMENDED DC OPERATING CONDITIONS 1)Note:1. Industrial Product: T A =-40 to 85°C, Otherwise specifiedAutomotive Product: T A =-40 to 125°C, Otherwise specified 2. Overshoot: Vcc+3.0V in case of pulse width ≤30ns.3. Undershoot: -3.0V in case of pulse width ≤30ns.4. Overshoot and undershoot are sampled, not 100% tested.ItemSymbol Min Typ Max Unit Supply voltage Vcc 4.5 5.0 5.5V GroundVss 000V Input high voltage V IH 2.2-Vcc+0.52)V Input low voltageV IL-0.53)-0.8VCAPACITANCE 1) (f=1MHz, TA=25°C)1. Capacitance is sampled, not 100% testedItemSymbol Test ConditionMin Max Unit Input capacitance C IN V IN =0V -8pF Input/Output capacitanceC IOV IO =0V-10pFDC AND OPERATING CHARACTERISTICSItemSymbol Test ConditionsMin Typ Max Unit Input leakage current I LI V IN =Vss to Vcc-1-1µA Output leakage current I LO CS=V IH or OE=V IH or WE=V IL , V IO =V SS to Vcc -1-1µA Operating power supply current I CC I IO =0mA, CS=V IL, V IN =V IH or V IL , Read--5mA Average operating currentI CC1Cycle time=1µs, 100% duty, I IO =0mA, CS ≤0.2V, V IN ≤0.2V IN ≥Vcc -0.2V--7mA I CC2Cycle time=Min,100% duty, I IO =0mA, CS=V IL, V IN =V IH or V IL --25mA Output low voltage V OL I OL =2.1mA --0.4V Output high voltage V OH I OH =-1.0mA2.4--V Standby Current(TTL)I SB CS=V IH , Other inputs=V IH or V IL --0.4mA Standby Current (CMOS)I SB1CS ≥Vcc-0.2V, Other inputs=0~VccK6X0808C1D-F --15µA K6X0808C1D-Q--50µAC L 1)1. Including scope and jig capacitanceAC OPERATING CONDITIONSTEST CONDITIONS (Test Load and Test Input/Output Reference)Input pulse level: 0.8 to 2.4V Input rising and falling time: 5nsInput and output reference voltage: 1.5V Output load (See right): C L =100pF+1TTL C L =50pF+1TTLAC CHARACTERISTICS (Vcc=4.5~5.5V, Industrial product: T A =-40 to 85°C, Automotive product: T A =-40 to 125°C)1. The parameter is tested with 50pF test load. Industrial Product only.Parameter ListSymbolSpeed BinsUnits551)ns 70ns MinMaxMin Max ReadRead cycle time t RC 55-70-ns Address access time t AA -55-70ns Chip select to output t CO -55-70ns Output enable to valid outputt OE -25-35ns Chip select to low-Z output t LZ 10-10-ns Output enable to low-Z output t OLZ 5-5-ns Chip disable to high-Z output t HZ 020030ns Output disable to high-Z output t OHZ 020030ns Output hold from address change t OH 10-10-ns WriteWrite cycle timet WC 55-70-ns Chip select to end of write t CW 45-60-ns Address set-up time t AS 0-0-ns Address valid to end of writet AW 45-60-ns Write pulse width t WP 40-50-ns Write recovery time t WR 0-0-ns Write to output high-Z t WHZ 020025ns Data to write time overlap t DW 25-30-ns Data hold from write time t DH 0-0-ns End write to output low-Zt OW5-5-nsDATA RETENTION CHARACTERISTICSItemSymbol Test ConditionMin Typ Max Unit Vcc for data retention V DR CS ≥Vcc-0.2V2.0- 5.5V Data retention current I DR Vcc=3.0V, CS ≥Vcc-0.2V K6X0808C1D-F --10µAK6X0808C1D-Q--25Data retention set-up time t SDR See data retention waveform0--ms Recovery timet RDR5--Address Data OutTIMING DIAGRAMSTIMING WAVEFORM OF READ CYCLE(1)(Address Controlled, CS=OE=V IL, WE=V IH)TIMING WAVEFORM OF READ CYCLE(2) (WE=V IH)CSAddressOEData ou tNOTES (READ CYCLE)1. t HZ and t OHZ are defined as the time at which the outputs achieve the open circuit conditions and are not referenced to output voltagelevels.2. At any given temperature and voltage condition, t HZ(Max.) is less than t LZ(Min.) both for a given device and from device to deviceinterconnection.TIMING WAVEFORM OF WRITE CYCLE(2)(CS Controlled)AddressCSWEData inData out High-Z High-ZNOTES (WRITE CYCLE)1. A write occurs during the overlap of a low CS and a low WE. A write begins at the latest transition among CS going Low and WEgoing low : A write end at the earliest transition among CS going high and WE going high, t WP is measured from the begining of write to the end of write.2. t CW is measured from the CS going low to the end of write.3. t AS is measured from the address valid to the beginning of write.4. t WR is measured from the end or write to the address change. t WR applied in case a write ends as CS or WE going high.DATA RETENTION WAVE FORMCS controlledV CC4.5V2.2VV DRCSGNDData Retention ModeCS≥V CC - 0.2Vt SDR t RDRTIMING WAVEFORM OF WRITE CYCLE(1) AddressCSWEData inData outPACKAGE DIMENSIONSUnits: millimeter(inch)1.65#128 PIN DUAL INLINE PACKAGE(600mil)#2813.60±0.200.535±0.00836.32±0.201.430±0.008( )0.0651.52±0.100.060±0.0040.46±0.100.018±0.004 +0.10MAX36.721.4460.25 -0.05#14#152.540.100MAX3.81±0.200.150±0.0085.080.200MIN0.0150.380.130±0.0123.30±0.3028 PIN PLASTIC SMALL OUTLINE PACKAGE(450mil)0~8°#2811.81±0.300.465±0.01218.29±0.200.720±0.008MAX 18.690.736MAX2.59±0.200.102±0.0083.000.118MIN 0.0020.050.004 MAX0.10 MAX #150.41±0.100.016±0.004#1#140.89( )0.03511.430.4508.38±0.200.330±0.0081.02±0.200.040±0.008+0.100.15 -0.05+0.0040.006 -0.0021.270.050PACKAGE DIMENSIONS28 PIN THIN SMALL OUTLINE PACKAGE TYPE I (0813.4F)#281.00±0.100.039±0.004M A X8.400.3310.004 M A X 0.10 M A X 13.40±0.200.528±#15+0.100.425( )0.017MIN0.050.002MAX1.200.0478.000.315#281.00±0.100.039±0.004M A X8.400.3310.004 M A X0.10 M A X #10.50( )0.02011.80±0.100.465±0.0040.45 ~0.750.018 ~0.03013.40±0.200.528±0.008#15#14+0.100.15 -0.05+0.0040.006 -0.0020~8°0.425( )0.017MIN0.050.002MAX1.200.0478.000.315TYP0.250.0100.550.0217+0.100.20 -0.05+0.0040.008 -0.00228 PIN THIN SMALL OUTLINE PACKAGE TYPE I (0813.4R)Units: millimeter(inch)。
LED18WT8F 48 XXX-G5D和LED18WT8F 48 XXXK-G6D系列LED灯具说
LED18WT8F/48/XXX-G5D series LED18WT8F/48/XXXK-G6D series Min. Dimension of Lighting Fixture : 1215 x 600 x 80 mm Max. 4 pcs LED tubes allowed, each tube spaced 15.5 cm apart.The tube can be extended utilizing with four in one ceiling or type IC recessed luminaires. The retrofit consists of installation manual(1 pcs), LED tube(1 pcs), relamping and cautionary label(1 pcs).Installation GuideFigure ARetrofit with One lampRetrofit Instruction ** During Retrofit, rewiring is a MUST, please always follow the installation instruc-tion below.1) Ensure power is off to luminaire by disconnecting the supply voltage 2) Remove all fluorescent lamps and starters, cut off all wires which are connected to ballast.3) Wire luminaire to the configuration shown on drawing figure A/B (Note: LED T8 tube will not work with shunted lamp holders.)4) Place warning label found in LED retrofit lamp package to ensure that the user understands that the system now uses LED tubes and replacement with fluorescent can cause damage 5) Insert LED retrofit lamp 6) Turn power back on and check for proper operationBEFORE YOU BEGIN Read these instructions completely and carefully.WARNING Risk of fire or electric shock. LED Retrofit installation must be done by a qualified electrician only and all safety instructions must be followed to avoid a risk of injury or property damage.WARNING Risk of Electric Shock. Disconnect power before installation of the product.LED T8 Tube Lights Figure BRetrofit with Two lamp and one ballastCAUTION-To avoid potential fire or shock hazard, do not use this retrofit lamp in luminaires em-ploying shunted bi-pin lampholders. Note: shunted lamp holders are found only in fluo-rescent luminaires with Instant-Start ballast, which can be indentified by the words “Instant Start” or “I.S” marked on the ballast.-A label needs to be placed onto the fixture in a location that is visible during retrofit that has the following caution. “*This luminaire has been modified and can no longer operate the originally intended lamp. *The LED retrofit has been installed and fixture has been modified so that it only works with EIKO product.”-NOT FOR USE WITH DIMMERSSafety Notes-Do not place lamps near combustible materials such as paper, alcohol, paint, etc., so as not to cause fire or electric shock-Under abnormal situations, please power off the lamp to repair and check, such as parts, light loose, cracking, smoking, and abnormal luminescence.-Do not expose to high humidity environment, since this lamp is only suitable for indoor -WARNING: To avoid potential fire or shock hazard, do not use this retrofit kit in lumi-naires employing shunted bi-pin lampholders. Note: Shunted lamp holders are found only in fluorescent luminaires with Instant-Start ballasts. Instant-start ballasts can be identified by the words “Instant Start” or “I.S.” marked on the ballast. This designation may be in the form of a statement pertaining to the ballast itself, or may be combined with the marking for the lamps with which the ballast is intended to be used, for example F40T12/IS. For more information, contact the LED luminaire retrofit kit manufacturer.-WARNING – Risk of fire or electric shock. LED Retrofit Kit installation requires knowl-edge of luminaires electrical systems. If not qualified, do not attempt installation. Con-tact a qualified electrician-WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the lumi-naire.-Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.-Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder terminals. Instead installers should cut existing lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by employing applicable connectors.-WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.-WARNING – Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.-NOT FOR EMERGENCY LIGHTING。
0805双色贴片LED灯珠规格书-鑫光硕
0805双⾊贴⽚LED灯珠规格书-鑫光硕Customer:·Technical Data SheetPN: XGS-PB2012UEUBFor: IF=20mAContents1.Features2.Applications3.Package dimensions4.Absolute maximum rating5.Electrical optical characteristics6.BIN range7.Package label8.Soldering pad dimensions9.Soldering conditions10.Package tape specifications11.T ypical electro-optical characteristics curves12.Reliability test items and conditions13.Cautions14.Note◆F eatures:Compatible with automatic placement equipmentCompatible with reflow solder processLow power consumption and wide viewing angleThis product doesn’t contain restriction Substance, comply ROHS standard.◆A pplications:Automotive and TelecommunicationFlat backlight for LCD ,switch and symbol in telephone and faxGeneral use for indicators◆P ackage Dimensions:Electrodes: Au PlatingEncapsulating Resin: Epoxy ResinPackage: BT ResinUnit:mmTolerance:±0.1Absolute Maximum Rating （Ta=25℃）I FP condition: pulse width ≤1ms ,duty cycle ≤1/10 Electrical Optical Characteristics（Ta=25℃）Notes: 1.Tolerance of Luminous Intensity ±10%2.Tolerance of Dominant Wavelength ±2nm3.Tolerance of Forward Voltage ±0.05V4.Luminous Intensity is measured by XGS’s equipment on bare chips◆ Soldering Pad Dimensions:◆ Soldering Conditions (Maximum allowable soldering conditions)Reflow soldering profileReflow soldering should not be done more than two times. Do not stress its resin while soldering. After soldering,do not warp the circuit board.T e m p e r a t u r e◆P ackage Tape Specifications: (4000 pcs/Reel)Feeding, Direction Dimensions of Reel ( Unit: mm)Dimensions of Tape (Unit:mm)Arrangement of Tape(Unit:mm)◆T ypical Electro-Optical Characteristics Curves：Reliability(1)Test Items and Conditions(2)C riteria of judging the damage◆C autions1、PackageWhen moisture is absorbed into the package it may vaporize and expand during soldering. There is apossibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. So the moisture proof package is used to keep moisture to a minimum in the package.2、StorageBefore opening the package: The LEDs should be kept at 5~30°C and 60%RH or less. The LEDs should be used within a year.After opening the package: The LED must be used within 24 hours, else should be kept at 5~30℃and 30% RH or less. The LEDs should be used within 7days after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again.If the LEDs have exceeded the storage time, baking treatment should be performed more than 24hours at 60±5°C.3、Soldering IronEach terminal is to the tip of soldering iron temperature less than 300℃ for 3 seconds within once inless than the soldering iron capacity 25 W.Leave two seconds and more internals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.4、RepairingRepairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.5、The LED electrode sections are comprised of a gold plated. The gold surface may be affected by environments which contain corrosive gases and so on. Please avoid conditions which may cause the LED to corrode or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible.6、Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur.◆N otes:1、Above specification may be changed without notice. We will reserve authority on material change for above specification.2 、When using this product, please observe the absolute maximum ratings and the instructions for the specification sheets. We assume no responsibility for any damage resulting from use of the product which does not comply with the instructions included in the specification sheets.Page 8 of 8。
LED灯具规格书-中英文
75g
单件内包装方式Piece Packing Type
PE袋+PE Bag+White Box
单件内包装尺寸Piece Packing Size
L:60 W:60 H:25(mm)
外包装批量大小Carton Size
25PCS/箱25Pcs/Carton Box
编制Prepared By
安装型式Mounting Type
固定灯座上安装Lamp Holder
PCB材质PCB Type
玻纤板GF Base PCB
灯体/散热材质Heatsink Type
铝合金Al Alloy
灯罩材质Cover Material
聚碳酸酯PCPC Cover
灯罩类型Cover Type
透明罩Transparent
审核Checked By
核准Approved By
输入电压VInput Voltage
AC 100-240V
电源频率AC Frequency
50-60Hz
输出电压Output Voltage
DC Vdc
输出电流Output Current
DC Adc
电源效率Driver Efficiency
η≥85%
功率因数Power Factor
PF≥0.95
光学特性OPTICAL
1200±25Lm
显色指数Color Renderlndex
Ra≥
配光平均光束角Beam Angle
110°
工作寿命Lifespan(Hrs)
灯体5000，电源30000LED:5000,P/S3000
结构特性
STRUCTLeabharlann RAL产品外型尺寸Dimension(mm)
RL0805FR-070R51L;RL2512FK-07R018L;RL0805JR-070R22L;RL0402FR-070R68L;中文规格书,Datasheet资料
-
-
LPRC201 2322 ±1% 0.01 to 1 Ω 735 7xxxx
-
-
2010 LPRC111 2322 ±5% 0.01 to 0.0976 Ω 760 90xxx
-
-
LPRC111 2322 ±5% 0.1 to 1 Ω
760 60xxx
-
-
LPRC111 2322 ±1% 0.01 to 0.0976 Ω 761 90xxx
APPLICATIONS Converters Printer equipment Server board Telecom Consumer
FEATURES Halogen Free Epoxy RoHS compliant - Products with lead free terminations meet RoHS requirements - Pb-glass contained in electrodes, resistor element and glass are exempted by RoHS Reducing environmentally hazardous wastes High component and equipment reliability Saving of PCB space None forbidden-materials used in products/production Low resistances applied to current sensing
-
-
LPRC111 2322 ±1% 0.1 to 1 Ω
761 6xxxx
-
-
2512 LPRC221 2322 ±5% 0.01 to 0.0976 Ω 762 90xxx
EJ080NA-05B Pre- SPEC(V01)-杭州旭虹科技有限公司
a-Si TFT active matrix
3 Resolution
800 × 3(RGB) × 600
4 Display mode
Normally White, Transmissive
5 Dot pitch
0.0675(W) × 0.2025(H) mm
6 Active area
162.0(W) × 121.5(H) mm
CHIMEI INNOLUX DISPLAY CORPORATION
LCD MODULE
工业液晶屏：ｗｗｗ．ｈｚｘｕｈｏｎｇ．ｃｏｍ
S P E C I F I C AT I O N
Customer: Model Name: Date: Version:
EJ080NA-05B 2011/04/28 01
CHIMEI INNOLUX 1. General Specifications
Date :2011/04/28 Page:1/20
No.
Item
Specification
Remark
1 LCD size
8.0 inch(Diagonal)
2 Driver element
3.1. Absolute Maximum Rating.............................................................................................. 5 3.1.1. Typical Operation Conditions.................................................................................. 6 3.1.2. Current Consumption ............................................................................................. 7 3.1.3. Backlight Driving Conditions ................................................................................... 7
JEL801-2010日本LED灯管标准(中文)
JEL801日本球泡灯工业协会规格带L形灯头的直管形LED灯体系(一般照明用)JEL801： 20102010年（平成22年）10月8日 制定社团法人 日本电灯工业协会目 录序文 ------------------------------------------------------------------------- --------------------11 适用范围---------------------------------------------------------------------------------------12 引用说明---------------------------------------------------------------------------------------13 术语及其定义-----------------------------------------------------------------------------------24 灯的要求事项-----------------------------------------------------------------------------------45 灯的安全性要求事项-----------------------------------------------------------------------------56 灯的性能要求事项-------------------------------------------------------------------------------107 灯的形式---------------------------------------------------------------------------------------118 灯的表示---------------------------------------------------------------------------------------129 控制装置的要求事项-----------------------------------------------------------------------------1310 灯座的要求事项--------------------------------------------------------------------------------14 附属书A（规定） 灯头表面温度上升实验------------------------------------------------------------18 附属书B（规定） 灯的电特性以及光特性的实验方法--------------------------------------------------19 附属书C（规定）灯的光通量维持率以及寿命实验的电灯条件-------------------------------------------20 附属书D （参考）灯的形式------------------------------------------------------------------------21 附属书E（规定）灯座一览表-----------------------------------------------------------------------22 11. 数据资料------------------------------------------------------------------------------------23 11.1 灯的数据资料No.的一般法则-----------------------------------------------------------------23 11.2 灯的尺寸测定位置的图示数据资料-------------------------------------------------------------23 11.3 灯的数据资料-------------------------------------------------------------------------------23日本电灯工业协会规格JEL801:2010 带L形灯头的直管形LED灯体系(一般照明用)1.适用范围本规格只使用于一般照明，针对使用L形灯头的直流电流供电的直管形LED灯、控制装置以及灯座的安全性、互换性以及性能方面所规定的要求事项以及判定该产品是否合格的必要的实验方法。
0805LED灯珠翠绿色贴片LED灯珠0805规格书
Customer:·Technical Data Sheet PN:XGS-PB2012UG-02 For:IF=5mAContents1.Features2.Applications3.Package dimensions4.Absolute maximum rating5.Electrical optical characteristics6.BIN range7.Package label8.Soldering pad dimensions9.Soldering conditions10.Package tape specifications11.T ypical electro-optical characteristics curves12.Reliability test items and conditions13.Cautions14.Note◆F eatures:Compatible with automatic placement equipmentCompatible with reflow solder processLow power consumption and wide viewing angleThis product doesn’t contain restriction Substance, comply ROHS standard.◆A pplications:Automotive and TelecommunicationFlat backlight for LCD ,switch and symbol in telephone and faxGeneral use for indicators◆P ackage Dimensions:Unit:mmTolerenc e±0.1Electrodes: Ag Plating◆A bsolute Maximum Rating （Ta=25℃）* I FP condition: pulse width ≤1ms ,duty cycle ≤1/10◆E lectrical Optical Characteristics（Ta=25℃）Notes: 1.Tolerance of Luminous Intensity ±10%2.Tolerance of Dominant Wavelength ±2nm3.Tolerance of Forward Voltage ±0.05V4.Luminous Intensity is measured by XGSLED’s equipment on bare chips◆S oldering Pad Dimensions:◆ S oldering Conditions (Maximum allowable soldering conditions)Reflow soldering profile <Pb-free solder>Time• Reflow soldering should not be done more than two times. • Do not stress its resin while soldering.• After soldering,do not warp the circuit board.T e m p e r a t u r e◆ P ackage Tape Specifications: (3000 pcs/Reel)Reel Lead Min.60mm No LEDs5 Reels in one Box10 Boxes in one Carton◆ T ypical Electro-Optical Characteristics Curves ：Forward Current Vs Ambient Temperature5040302010100250Forward Current Vs Relative Luminosity204060801001020304050Ambient Temperature Ta (° C)Forward Current (mA)200 15010050 Relative Luminosity VsAmbient TemperatureIf=15mA-50° -60°-70°-80°-90°-40°-30°-20°-10°0°10°20°30°40°50°60°70°80°90° 0 0204060801001.00.50.5Radiation Angle1.0Ambient Temperature Ta (° C)R e l a t i v e L u m i n o s i t y (%)F o r w a r d C u r r e n t (m A )R e l a t i v e L u m i n o s i t y (%)◆Reliability(1)Test Items and Conditions(2)C riteria of judging the damage◆C autions1、PackageWhen moisture is absorbed into the package it may vaporize and expand during soldering. There is apossibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. So the moisture proof package is used to keep moisture to a minimum in the package.2、StorageBefore opening the package: The LEDs should be kept at 5~30°C and 60%RH or less. The LEDs should be used within a year.After opening the package: The LED must be used within 24 hours, else should be kept at 5~30℃and 30% RH or less. The LEDs should be used within 7days after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again.If the LEDs have exceeded the storage time, baking treatment should be performed more than 24hours at 60±5°C.3、Soldering IronEach terminal is to the tip of soldering iron temperature less than 300℃ for 3 seconds within once inless than the soldering iron capacity 25 W.Leave two seconds and more internals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.4、RepairingRepairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.5、The LED electrode sections are comprised of a gold plated. The gold surface may be affected by environments which contain corrosive gases and so on. Please avoid conditions which may cause the LED to corrode or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible.6、Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur.◆N otes:1、Above specification may be changed without notice. We will reserve authority on material change for above specification.2 、When using this product, please observe the absolute maximum ratings and the instructions for the specification sheets. We assume no responsibility for any damage resulting from use of the product which does not comply with the instructions included in the specification sheets.。
RC0805资料
Thick Film Chip Resistor – General PurposeFeatures• Small and light weight• Excellent heat resistance and moisture resistance• Suitable size and packaging for surface mount assembly • RoHS CompliantApplications• For general purpose applications• For laptop and notebook computer, memory module, digital camera and telecommunication equipmentAbsolute Maximum Ratings & CharacteristicsProductNumbermm TolerancePower Rating @70˚CMAX Working Voltage MAXOverload VoltageTCR ppm/℃Resistance RangeRated WorkingTemperature±200 1Ω ~ 9.76Ω±100 10Ω ~ 1M ΩRC0805 2012J: ±5%F: ±1%1/8W 150V 300V ±2001.02M Ω ~ 10M Ω-55℃~+155℃*JumperProduct NumberJumper Rated CurrentResistanceRated Working Temperature RC0805 2A 50m Ω (max.)-55℃~+155℃RC0805 Power Derating CurveFor resistors operate in the ambient temperature over 70˚C, loading power ratio will de-rate in accordance with following curve.Soldering ConditionIR Reflow soldering Wave soldering (flow soldering)RC0805 Dimensions (in mm)ProductNumbermm L W H A BAverageWeight RC08052012 2.00 ± 0.101.25± 0.100.50 ± 0.100.35 ± 0.200.40 ± 0.20 4.54 mg Marking(1) ±5% Tolerance (J): 3 digits, the first two digits are significant figures; the third digit is numberof zeros to follow. Letter “R” is as decimal point; Letter “0” for jumper.(2) ±1% Tolerance (F): 4 digits, the first three digits are significant figures; the fourth digit isnumber of zeros. Letter “R” is as decimal point; Letter “0” for jumper.Examples:3 digits marking (±5%)4 digits marking (±1%)683 = 68x103Ω Jumper 6812 = 681x102Ω= 68000 Ω = 68KΩ = 68100 Ω = 68.1KΩ7R5 = 7.5 ΩRC0805 Test and RequirementsRequirement Test Item Test Method Test Condition±1% ±5% JumperTemperature Coefficient of Resistance(T.C.R.) JIS C 5201 4.8IEC 60115-1 4.8-55°C~+155,20°C isthe referencetemperatureWithin the specificationShort Time Overload JIS C 5201 4.13IEC 60115-1 4.132.5 times RCWV or max.overload voltage for 5seconds±(1.0%+0.05Ω) ±(2.0%+0.05Ω) <50mΩInsulation Resistance JIS C 5201 4.6IEC 60115-1 4.6Max. overload voltagefor 1 minute≥10GVoltage Proof JIS C 5201 4.7IEC 60115-1 4.71.42 times RCWV(RMS) for 1 minuteno breakdown or flashoverSubstrate Bending Test JIS C 5201 4.33IEC 60115-1 4.33Bending once with 5seconds for 3 mm±(1.0%+0.05Ω) ±(1.0%+0.05Ω) <50mΩResistance to soldering heat JIS C 5201 4.18IEC 60115 4.18260±5°C for 10 seconds±(0.5%+0.05Ω) ±(1.0%+0.05Ω) <50mΩLeaching JIS C 5201 4.18IEC 60115 4.18260±5°C for 60 seconds no leachingSolderability JIS C 5201 4.17IEC 60115-1 4.17245±5°C for 3 seconds. >95% coverageEndurance at upper category temperature JIS C 5201 4.23IEC 60115-1 2.23.2at +155°C for 1000 hrs ±(1.0%+0.05Ω) ±(1.5%+0.10Ω) <50mΩRapid change of temperature JIS C 5201 4.19IEC 60115-1 4.19-55°C to +155°C, 5cycles±(0.5%+0.05Ω) ±(1.0%+0.05Ω) <50mΩDamp heat with load JIS 5201 4.2440±2°C, 90~95% R.H.or max. working voltagefor 1000 hrswith 1.5hrs “ON” and 0.5hrs “OFF”±(2.0%+0.10Ω) ±(3.0%+0.10Ω) <100mΩEndurance JIS C 5201 4.25IEC 60115-1 4.25.170±2°C, RCWV or Max.working voltage for 1000hrs with 1.5 hrs“ON” and 0.5 hrs “OFF”±(2.0%+0.10Ω) ±(3.0%+0.10Ω) <100mΩNote: RCWV：Rated Continuous Working Voltage.RCWV= √Rated power (W) × Resistance value (R)RC0805Packing Information:Carrier Tape Dimensions (in mm)TypeABWEF P0 P1 P2ψD0T RC0805 1.60±0.1 2.40±0.2 8.0±0.2 1.75±0.13.5±0.054.0±0.14.0±0.052.0±0.05 1.5+0.1/-00.85±0.1Reel Dimensions (in mm)Reel DiameterPCS per ReelABCWT7’’ 5,000 180+0/-360+1/-0 13.0±0.29.0±0.5 11.4±1 13’’ 20,000 330±1 100±1 13.0±0.29.5±0.5 13.5±1Carton InformationPCS per CartonCarton Size300,000 400X400X200 ( in mm)RC0805 How to OrderRC0805 How to contact us:。
光陽 VJR 125系列 機 車 使用說明書说明书
機車使用說明書NCC聲明低功率電波輻射性電機管理辦法：第㈩㆓條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅㉂變更頻率、加大功率或變更原設計之㈵性及功能。
第㈩㆕條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現㈲干擾現象時，應立即停用，並改善㉃無干擾時方得繼續使用。
前㊠合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科㈻及㊩療用電波輻射性電機設備之干擾。
前 言親愛的愛用者：承蒙選購光陽 VJR 125系列謹致萬分謝忱。
本使用手冊是將光陽VJR 125系列之正確操作方法與保養調整方法、要領等加以詳細說明以期耐久安全舒㊜的使用。
本車型符合機車環保法規排放管制標準，因此合乎低污染、低噪音、省能源的環保要求，雖然本車擁㈲良好的品質，但還是必需實施定期的保養，才能維持最佳的性能。
為了使您更安全、更舒㊜之行駛，敬請詳閱本手冊，謹此㈷您行車愉快。
本手冊之內容與實車如㈲所出入者，則以實車型式為準。
車輛識別號碼㈾訊1.引擎號碼:本機車引擎號碼壓㊞在㊧曲軸箱後方如圖示(1)：2.車架號碼:本機車車架號碼壓㊞在車架㆖如圖示(2)：重要㈾訊防竊盜烙碼為防止您的愛車失竊及配合政府打擊竊盜犯罪政策本機車交予顧客前在㊜當位置烙㊞防竊盜烙碼(如㆘圖所示)，其防竊盜烙碼與引擎號碼相同。
◎本圖為範例,其實際各烙碼位置以實車為準。
全車型在座墊㆘置物箱後方貼㈲車輛排氣管制㈾訊貼紙(如圖示1)㈲關貼紙其內容如㆘：■車輛排氣管制㈾訊11防竊盜烙碼2機車㈾料記錄收集此機型的ECU可收集及記錄該機車之運轉相關㈾訊，用以㈿助車輛故障診斷及排除。
這些㈾訊需使用光陽專用的診斷工具連接㉃機車的診斷接頭才能取得，例如執行保養檢查或維修程序時。
如㊨圖示光陽機型可能感知器及記錄㈾訊因機種而異，但主要㈾訊為:1.機車狀態及引擎性能㈾訊。
2.機車噴射與排放相關㈾訊。
除非㈲㆘列情形，光陽機車公司不會將這些㈾訊洩漏給第㆔方:1.經車輛使用㆟及所㈲者同意。
Brightek 0805 1.1t系列 LED产品说明书
0805 1.1t S e r i e s0805 1.1t SeriesFEATURES:∙Package: PCB / CHIP LED ∙Forward Current: 20mA ∙Forward Voltage (typ.): 2.1V∙Luminous Intensity (typ.): 150mcd @20mA ∙Colour: Yellow∙Wavelength: 590nm ∙Viewing angle: 140° ∙Materials:-Die: AlGaInP/GaAs-Resin: Epoxy (Water Clear) ∙Operating Temperature: -40~+80°C ∙Storage Temperature: -40~+85°C ∙Grouping parameters: -Forward voltage -Luminous intensity -D ominant wavelength ∙Soldering methods: Reflow∙Preconditioning: acc. to JEDEC Level 3∙Packing: 8mm tape with 3000/reel, ø180mm (7’’)N0Y10S46APPLICATIONS:∙ Backlighting ∙ Indication Light ∙ Switch light ∙DashboardRelease Date: 23 July 2014 Version: A1.0PRODUCT DATASHEET ► PCB / CHIP LED► 0805 (1.1t) ► Yellow (590nm)CHARACTERISTICS:Absolute Maximum Characteristics (Ta=25°C)1.Luminous intensity (I V) ±15%, Forward Voltage (V F) ±0.1V, Viewing angle(2θ1/2) ±5%2.IS standard testingOUTLINE DIMENSION:Package Dimension:1. All dimensions are in millimetre (mm).2.Tolerance ±0.2mm, unless otherwise noted.Recommended Soldering Pad Dimension:1. Dimensions are in millimetre (mm).2. Tolerance ±0.1mm with angle tolerance ±0.5°.Anode CathodeBINNING GROUPS:Forward Voltage Classifications (I F = 20mA):IIELECTRO-OPTICAL CHARACTERISTICS:Wavelength (nm) Forward Current (mA)RECOMMENDED SOLDERING PROFILE:Reflow Solder:Note:1.Recommend reflow temperature 245°C.2.Maximum reflow soldering: 2 times.3.Before, during, and after soldering, should not apply stress on the components and PCBboard.PACKING SPECIFICATION:PRECAUTIONS OF USE:Storage:It is recommended to store the products in the following conditions:∙Humidity: 60% R.H. Max.∙Temperature: 5°C~30°C (41°F ~86°F).Shelf life in sealed bag: 12 month at 5°C~30°C and <60% R.H.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp-proof box with descanting agent and apply baking at 60°C±5°C for 15hrs before use. Baking:It is recommended to bake the LED before soldering if the pack has been unsealed for longer than 24hrs.The suggested baking conditions are as followings:∙70±3°C x 24hrs and <5%RH, taped / reel package.∙100±3°C x 2hrs, bulk (loose) package.∙130±3°C x 30min, bulk (loose) package.It’s normal to see slight color fading of carrier (light yellow) after baking in process.Testing Circuit:Must apply resistor(s) for protection (over currentproof).Cleaning:Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED carrier / package. Avoid putting any stress force directly on to the LED lens.ESD (Electrostatic Discharge):Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing the LED all time. All devices, equipment, machinery, work tables, and storage racks must be properly grounded.In the events of manual working in process, make sure the devices are well protected from ESD at any time.REVISION RECORD:。
日立液晶电视遥控器规格书_中文版(080826)
BCDEFCLE-1002遥控器1.适用范围：本规格书适用于HITACHI —PDP 、MS 用红外遥控发射器。
2.外观尺寸与构造：项 目 试 验 条 件 判 定 基 准 2.1 外观 下列项目均目测确认 ① 划伤、沾污、割裂、弯曲、收缩、刮痕、变形 ② 印刷图形及文字 ③ 壳体配合 ④ 表面① 无上述各现象② 清晰、均匀、整齐 ③ 无翘起、变形、裂缝④ 材质均匀、颜色一致2.2 结构外形尺寸 230×51×27 见第5页2.3 部品重量 设计重量106 g ±5g （电池除外） 106g ±5g3.使用部品及材料： 部品使用及材料与设计图纸及规格一致。
4.性能 4-1使用条件4-1-1温度范围 0℃～+40℃（45～85％RH ），大气压86～106Kpa 4-1-2 高温范围 +40℃/85％RH(Max) 4-1-3保存温度范围 –10℃～+60℃ 4-1-4 试验环境 温度5～35℃、相对湿度45～85％RH 、大气压86～106Kpa 4-2 测量和环境条件 除非特殊说明，所有的测量条件为温度25℃±3℃ 和 相对湿度65％RH ±5％，电源电压3.2VDC 或新电池。
4-3电气特性 4-3-1使用电源（DC2.2V ～3.3V ,）干电池：AA ×2个 4-3-2晶振频率起始频率：4MHz ±0.5% 载波： TV ：37.9KHz ±2% 4-3-3消耗功耗 17±5 mA (发送时) 4-3-4漏电流5µA 以下4-3-5晶振停止电压： 2.2VDC 或以下 4-3-6到达距离及方向灵敏度 ⑴在电源电压3.2V 或新电池时接收机 遥控器Ø ØBCDEFa) 正面到达距离15.0m 以上, 或等效发射功率不小于50uW/cm 2；（国标为不小于40uW/cm 2） b) 角度为15º时为12.0m 以上，或等效发射功率不小于25uW/cm 2；（国标为不小于20uW/cm 2）下限品标准如下为不可接受：c) 正面到达距离14.0m 或以下, 或等效发射功率不大于40uW/cm 2；（国标为不大于40uW/cm 2） d) 角度为15º时为11.0m 或以下，或等效发射功率不大于20uW/cm 2；（国标为大于20uW/cm 2） ⑵当电压减到为2.4V 时所能到达的距离为在电压在3V 时的70％以上。
0805贴片led灯珠（台宏光电0805贴片led灯珠一览表）
0805贴片led灯珠（台宏光电0805贴片led灯珠一览表）0805贴片led灯珠（台宏光电0805贴片led灯珠一览表），见后面。
一、0805贴片led灯珠找到对应的型号才适用。
很多人问0805贴片led灯珠，就是了解一下0805灯珠参数。
要是清楚0805灯珠型号，找起来会更加方便。
不清楚的，可以按颜色来找。
比如，按0805冷白光，0805红光，0805橙光，0805黄光，0805翠绿，0805黄绿，0805蓝光、0805双色灯珠、0805三色、0805全彩灯珠等。
知道了颜色，知道了亮度要求，LED灯珠厂家就可以根据你的需求给你匹配对应的0805灯珠样品。
有些公司的采购，对这些灯珠的参数，不是很清楚。
因为大部分这些灯珠的需求者都是工程，研发部门。
他们有灯珠采购需求，参数要求，都是走公司流程，传达到采购部门，去采购。
所以，更多的时候，采购是按照工程的要求来找0805LED灯珠的。
二、但是，具体的0805贴片led灯珠的要求是什么，用途她可能不是很清楚。
对于恒压恒流，是否视觉光源使用，有没有一致性要求，这个她们一般都是不清楚的。
所以，找对人，了解真正的需求，很重要。
这也是0805灯珠厂家台宏光电的销售主管，一直要求销售工程师，一定要具体了解客户的应用，再给推荐的原因。
不同的产品应用，对产品的等级要求是不同的。
很多人，只看到是同一款的灯珠型号，但是这款灯珠的应用，是中高端产品，还是普通的数码显示应用，要求是不同的。
不同在哪里呢？三、一种是用的材料不同，比如，台宏光电的0805灯珠，按常规亮度，有普通亮度和高亮的0805灯珠。
这里面用的芯片材质，芯片大小，是不一样的。
同样，用在医疗产品，和用在鞋灯，广告灯上的产品要求也是不一样的。
事实上，除了材料的不同，LED灯珠厂家的封装工艺，技术，封装设备不同，生产出来的灯珠成品也会不同。
具体区别在哪里呢？我给你讲过故事你就知道了。
去年夏天，我们办公室有个同事买了个玻璃壶，在办公室常常用开水泡罗汉果茶喝。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
A MARKING
T PACKAGING
VJ = MLCC
0603 0805 1206 1210
Q = High Q
A = Unmarked
Expressed in picofarads (pF). The first two digits are significant, the third is a multiplier. An “R” indicates a decimal point. Examples: 102 = 1000pF. 1R8 = 1.8pF.
ORDERING INFORMATION
VJ PRODUCT SERIES
0805 CASE SIZE
Q DIELECTRIC
102 CAPACITANCE NOMINAL CODE
A K X DC CAPACITANCE TERMINATION VOLTAGE TOLERANCE RATING A = 50V B = 100V C = 200V
10000 1000 100 10 1 100 FREQUENCY (MHz) Q vs FREQUENCY - VJ1210, 50V 1000 1000
ESR (Ω)
10pF 0.1 100pF
Q
100pF
0.01 100 FREQUENCY (MHz) ESR vs FREQUENCY - VJ1210, 50V 1 1000
31
元器件交易网
VJ High Q Dielectric
Vishay Vitramon
HIGH Q DIELECTRIC
STYLE E.I.A. TYPE VOLTAGE (VDC) Capacitance Code 1R0 1R2 1R5 1R8 2R2 2R7 3R3 3R9 4R7 5R6 6R8 8R2 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 821 Capacitance pF 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 50 VJ0603 0603 100 — 50 VJ0805 0805 100 200 50 VJ1206 1206 100 200 50 VJ1210 1210 100 200
GENERAL SPECIFICATIONS
NOTE: Electrical characteristics @ + 25°C unless otherwise specified. Capacitance Range: 1.0pF to 680pF. Temperature Coefficient of Capacitance (TCC): 0 ± 30PPM/°C from - 55°C to + 125°C. Dissipation Factor (DF): 0.1% maximum @ 1.0 Vrms and 1kHz for values > 1000pF. 0.1% maximum @ 1.0 Vrms at 1MHz for values ≤ 1000pF. Insulation Resistance (IR): @ + 25°C and rated voltage 100,000 Megohms minimum or 1000 ohm-farads, whichever is less. @ + 125°C and rated voltage 10,000 Megohms minimum or 100 ohm-farads, whichever is less. Dielectric Withstanding Voltage (DWV): 250% of rated voltage for 5 ± 1 seconds, 50 milliamps current maximum.
X = Nickel barrier with 100% tin plated finish F = Palladium silver
T = 7" Reel, plastic tape C = 7" Reel, paper tape R = 11 1/4" Reel, plastic tape P = 11 1/4" Reel, paper tape B = Bulk NOTE: 0402 and 0603 available in paper tape only
RESONANT FREQUENCY (GHz)
TEMPERATURE COEFFICIENT OF CAPACITANCE 2.0 1.5 1.0 0.5 0.0 - 0.5 - 1.0 - 1.5 - 2.0 -75 -50 -25 0 25 50 75 100 125 TEMPERATURE °C Q vs FREQUENCY - VJ0805, 50V 10000 10pF 1000 1 HIGH Q SERIES RESONANT FREQUENCY - HIGH Q 10
100
ESR (Ω)
180pF 0.1 680pF
Q
10 100
680pF
180pF 1000
0.01 100 FREQUENCY (MHz) 1000
FREQUENCY (MHz)
Document Number 45050 Revision 06-Apr-01
33
元器件交易网
VJ High Q Dielectric
Vishay Vitramon
Multilayer Ceramic Chip Capacitors
FEATURES
• COG is an ultra-stable dielectric offering a Temperature Coefficient of Capacitance (TCC) of 0 ± 30PPM/°C over the entire temperature range. • Low Dissipation Factor (DF). • Ideal for critical timing and tuning applications.
32
Document Number 45050 Revision 06-Apr-01
元器件交易网
VJ High Q Dielectric
Vishay Vitramon
HIGH Q - DIELECTRIC TYPICAL PARAMETERS
% CAPACITANCE CHANGE
1 1206 0.1 1
0603 0805
1210
10 100 CAPACITANCE (pF)
1000
ESR vs FREQUENCY - VJ0805, 50V
ESR (Ω)
100 10 1 100
101000 FREQUENCY (MHz) Q vs FREQUENCY - VJ1206, 50V 100 FREQUENCY (MHz) ESR vs FREQUENCY - VJ1206, 50V 1 10pF 1000
C = ± 0.25pF (1 to 25pF) D = ± 0.5pF (1 to 50pF) F = ± 1% (≥ 10pF) G= ± 2% (≥ 5pF) J = ± 5% (≥ 2pF) K = ± 10% (≥ 1pF)
Document Number 45050 Revision 06-Apr-01