42777-1中文资料
4787中文资料
FEATURES:• Cable connection for RG 58 and 142, 223, 141MATERIALS:Body and Fitting – Brass per QQ-B-626, Alloy 360, ½ HardCenter Contact – Gold Plated Brass per QQ-B-626, Alloy 360, ½ Hard Dielectric – PTFEGaskets and Seals: Silicone RubberFinish: Body and Fittings: Tarnish resistantCenter Contact: Gold flash over silver plate per QQ-S-365 RATINGS:Nominal Impedance: 50 OhmsDielectric Withstanding Voltage: 2500 VRMS, 1 Min., 60 Hz. ORDERING INFORMATION: Model 4787All dimensions are in inches. Tolerances (except noted): .xx = ±.02” (,51 mm), .xxx = ± .005” (,127 mm).All specifications are to the latest revisions. Specifications are subject to change without notice.Registered trademarks are the property of their respective companies.Made in USAFIGURE #1A. Slide clamp nut, flat washer and Vee gasket over cable.B. Strip cable jacket to dimensions shown.FIGURE #1AC. Slide braid clamp over braid positioned with the inner shoulder against the cable jacketD. Fold braid over braid clamp.E. Strip DielectricFIGURE #2F. Solder center contact to cable center conductor.FIGURE #3G. Slide clamp nut, flat washer and Vee gasket forward against braid clamp.A. Place connector body over end of cable, thread clamp nut into body and tighten.All dimensions are in inches. Tolerances (except noted): .xx = ±.02” (,51 mm), .xxx = ± .005” (,127 mm).All specifications are to the latest revisions. Specifications are subject to change without notice.Registered trademarks are the property of their respective companies.Made in USA。
MOOG_772_series_valves
771,772,773 SeriesServovalvesThe actual flow is dependent upon electrical command signal and valve pressure drop.The flow for a given valve pressure drop can be calculated using the square root function for sharp edge orifices:∆pQ = Q N∆pNQ [gpm] = calculated flow QN[gpm] = rated flow∆p [psi] = actual valvepressure drop∆p N [psi] = rated valvepressure drop771/2/3 SERIES SERVOVALVESThe 771/2/3 Series flow con-trol servovalves are throttlevalves for 3- and preferably4-way applications.They are ahigh performance,two-stagedesign that covers the range ofrated flows from 1 to 15 gpmat 1000 psi valve drop.Theoutput stage is a closed center,four-way sliding spool.The pilotstage is a symmetrical double-nozzle and flapper,driven bya double air gap,dry torquemotor.Mechanical feedback ofspool position is provided bya cantilever spring.The valvedesign is simple and rugged fordependable,long life operation.These valves are suitablefor electrohydraulic position,speed,pressure or force con-trol systems with high dynamicresponse requirements.Principle of operationAn electrical command signal(flow rate set point) is appliedto the torque motor coils,andcreates a magnetic force whichacts on the ends of the pilotstage armature.This causes adeflection of the armature/flap-per assembly within the flexuretube.Deflection of the flapperrestricts fluid flow through onenozzle which is carried throughto one spool end,displacingthe spool.Movement of the spoolopens the supply pressure port(P) to one control port,whilesimultaneously opening thetank port (T) to the othercontrol port.The spool motionalso applies a force to thecantilever spring,creating arestoring torque on thearmature/flapper assembly.Once the restoring torquebecomes equal to the torquefrom the magnetic forces,thearmature/flapper assemblymoves back to the neutralposition and the spool is heldopen in a state of equilibriumuntil the command signalchanges to a new level.In summary,the spoolposition is proportional to theinput current and with con-stant pressure drop across thevalve,flow to the load is pro-portional to the spool position. 2VALVE FEATURES¢ 2-stage design with dry torque motor¢Low friction double nozzle pilot stage¢High spool control forces¢High dynamics¢Rugged,long-life design¢High resolution,low hysteresis¢Completely set-up at the factory¢Small body size771/2/3 SERIESTWO ST AGE SERVOVAL VESThis catalog is for users with technicalknowledge.T o ensure that all necessarycharacteristics for function and safety of thesystem are given,the user has to check thesuitability of the products described here.In case of doubt,please contact Moog Inc.Intrinsically safe valve versions are available for use in hazardous locations.Specific models are certified to FM,ATEX,CSA,and TIIS standards.Contact the factoryfor details.3771/2/3 SERIESGENERAL TECHNICAL DA T AP B TAView from Pressure SideOperating Pressureports P ,T,A and B up to 3,000 psiT emperature RangeFluid -40°to 275°F Ambient -40°to 275°FSeal Material Viton others on request Operating FluidCompatible with common hydraulic fluids,other fluids on request.Recommended viscosity 60-450 SUS @ 100°F System Filtration:High pressure filter (without bypass,but with dirt alarm) mounted in the main flow and if possible,directly upstream of the valve.Class of Cleanliness:The cleanliness of the hydraulic fluidgreatly effects the performance (spool positioning,high resolution)and wear (metering edges,pressure gain,leakage) of the servovalve.Recommended Cleanliness ClassFor normal operation ISO 4406 < 14/11For longer life ISO 4406 < 13/10Filter Rating recommendedFor normal operation ß10≥75 (10 µm absolute)For longer life ß5≥75 (5 µm absolute)Installation Operations Any position,fixed or moveable.Vibration 30 g,3 axes Weight 2.0 lb [.09 kg]Degree of Protection EN50529P:class IP65,withmating connector mounted.Shipping Plate Delivered with an oil sealedshipping plate.4T ypical characteristiccurves with ±40% and ±100%input signal,measured at 3,000 psi operating pressure.Model…T ype771771773Mounting Pattern ISO 10372 - 02 - 02 - 0 - 92Valve Body Version 4-way2-stage with spool–bushing assemblyPilot StageNozzle/Flapper,HighflowPilot Connection Optional,Internal or External Internal onlyRated Flow (±10%) at ∆p N= 1,000 psi Standard [gpm] 1.0 2.5 5.010.015.0Response Time*Standard [ms]6661016Threshold*[%]< 0.5Hysteresis*[%]< 3.0Null Shiftat ∆T = 100˚F [%]< 2.0Null Leakage Flow*max.[gpm]0.35* Measured at 1,000 psi pilot or operating pressure771/2/3 SERIESTECHNICAL DA T AC4XSTR(.50.621.12 MAXTHRUTHRUSOCKETThe mounting manifoldmust conform toISO 10372-03-03-0-92.Surface to which valve ismounted requires a 32[∆∆]finish,flat within 0.002[0.05] TIR.For External Null Adjust:Flow out of Port B will increasewith clockwise rotation of nulladjust screw (3/32hex key).For External Null Adjust:Flow bias is continually variedfor a given port as the nulladjust is rotated.771/2/3 SERIESINST ALLA TION DRAWINGSTYPICAL SUBPLATE MANIFOLD5Rated current and coil resistanceA variety of coils are available for 771/2/3 Series Servovalves,which offer a wide choice of rated current.See Table 1.Coil connectionsA four-pin electrical con-nector (that mates with an MS3106F14S-2S) is standard.All four torque motor leads are available at the connector so external connections can be made for series,parallel or differential operation.771/2/3 Series Servovalves can be supplied on special order with other connectors or a pigtail.ServoamplifierThe servovalve responds to input current,therefore,a servoamplifier that has high internal impedance (as obtained with current feedback) should be used.This will reduce the effects of coil inductance and will minimize changes due to coil resistance variations.6Note:Before applying electrical signals the pilot stage has to be pressurized.* Measured at 50 Hz771/2/3 SERIESELECTRICAL CONNECTIONSModel Number T ype Designation Preferred configurations highlighted.All combinations may not be available.Options may increase price and delivery.T echnical changes are reserved.7771/2/3 SERIESORDERING INFORMA TIONSP ARE P ARTS AND ACCESSORIESAustralia Mulgrave Brazil São Paulo China Hong KongShanghai Denmark Cöpenhagen England T ewkesbury Finland Espoo France RungisGermany Böblingen India Bangalore Ireland Ringaskiddy Italy BresciaMalnate Japan Hiratsuka Korea Seoul Luxembourg Luxembourg City Philippines Baguio Singapore Singapore Spain Orio Sweden Askim USA East AuroraMoog Inc.,East Aurora,NY 14052-0018 T elephone:+1-716-652-2000 Fax:+1-716-687-7910T oll Free:+1-800-272-MOOG /industrial©2007 Moog Inc.All changes are reserved. CDL6304 Rev G 500-223 0807。
1827017中文资料
Extract from the online catalogThe illustration shows a 16-position version Plug component, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81 mm, no. of positions: 6, type of connection: Screw connectionOrder No.1827017Ord designation MCVW 1,5/ 6-ST-3,81 Catalog page information Page 85 (CC-2005) Technical dataTightening torque, min 0.22 NmTechnical dataInsulating material group IRated surge voltage (III/3) 2.5 kVRated surge voltage (III/2) 2.5 kVRated surge voltage (II/2) 2.5 kVRated voltage (III/2) 160 VRated voltage (II/2) 320 VConnection in acc. with standard EN-VDE8 ANominal current IN160 VNominal voltage UNNominal cross section 1.5 mm²Maximum load current 8 A (with 1.5 mm² conductor cross section) Insulating material PAInflammability class acc. to UL 94 V0Internal cylindrical gage A1Stripping length 7 mmConnection dataConductor cross section, rigid min. 0.14 mm²Conductor cross section, rigid max. 1.5 mm²Conductor cross section flexible min. 0.14 mm²Conductor cross section, flexible max. 1.5 mm²0.25 mm²Conductor cross section flexible, with ferrule withoutplastic sleeve min.Conductor cross section flexible, with ferrule without1.5 mm²plastic sleeve max.0.25 mm²Conductor cross section flexible, with ferrule with plasticsleeve min.0.5 mm²Conductor cross section flexible, with ferrule with plasticsleeve max.Conductor cross section AWG/kcmil min. 28Conductor cross section AWG/kcmil max 162 conductors with same cross section, solid min. 0.08 mm²2 conductors with same cross section, solid max. 0.5 mm²2 conductors with same cross section, flexible, min. 0.08 mm²2 conductors with same cross section, flexible max. 0.75 mm²0.25 mm²2 conductors with same cross section, flexible, ferruleswithout plastic sleeve min.0.34 mm²2 conductors with same cross section, flexible, ferruleswithout plastic sleeve, max.2 conductors with same cross section, flexible, TWIN0.5 mm²ferrules with plastic sleeve, min.2 conductors with identical cross section, flexible TWIN0.5 mm²ferrules with plastic sleeve, max.CertificatesCSA300 V Nominal voltage UNNominal current I8 ANAWG/kcmil 28-16 CULNominal voltage U300 VN8 A Nominal current INAWG/kcmil 30-14250 V Nominal voltage UNNominal current I8 ANAWG/kcmil 30-14 ULNominal voltage U300 VN8 A Nominal current INAWG/kcmil 30-14250 V Nominal voltage UN8 A Nominal current INAWG/kcmil 30-14Drawings Dimensioned drawingApproval logoAccessoriesItem Designation DescriptionMarking1051993B-STIFT Marker pen, for manual labeling of unprinted Zack strips, smear-proof and waterproof, line thickness 0.5 mm0804109SK 3,81/2,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 10-sectionmarker strip, 14 identical decades marked 1-10, 11-20 etc. up to91-(99)100, sufficient for 140 terminal blocks0805056SK 3,81/2,8:SO Marker card, special printing, self-adhesive, labeled acc. tocustomer requirements, 14 identical marker strips per card, max.25-position labeling per strip.0803883SK U/2,8 WH:UNBEDRUCKT Unprinted marker cards, DIN A4 format, pitch as desired, self-adhesive, with 50 stamped marker strips, 185 mm strip length,can be labeled with the CMS system or manually with the M-PENTools1205037SZS 0,4X2,5Screwdriver, bladed, matches all screw terminal blocks up to 1.5mm² connection cross section, blade: 0.4 x 2.5 mmAdditional productsItem Designation DescriptionGeneral1897843EMC 1,5/ 6-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: Press in1860689EMCV 1,5/ 6-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: Press in1857922IMC 1,5/ 6-ST-3,81Plug component, nominal current: 8 A, rated voltage: 160 V,pitch: 3.81 mm, no. of positions: 6, type of connection: Screwconnection1803316MC 1,5/ 6-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: Soldering1908800MC 1,5/ 6-G-3,81 THT Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: SMD/THT1829992MCD 1,5/ 6-G-3,81Header, nominal current: 7 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: Soldering1843114MCD 1,5/ 6-G1-3,81Header, nominal current: 7 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: Soldering1830444MCDV 1,5/ 6-G-3,81Header, nominal current: 7 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: Soldering1847767MCDV 1,5/ 6-G1-3,81Header, nominal current: 7 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: Soldering1861769MCO 1,5/ 6-GL-3,81Header, nominal current: 8 A, rated voltage: 125 V, pitch: 3.81mm, no. of positions: 6, mounting: Soldering1861688MCO 1,5/ 6-GR-3,81Header, nominal current: 8 A, rated voltage: 125 V, pitch: 3.81mm, no. of positions: 6, mounting: Soldering1803468MCV 1,5/ 6-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: Soldering1908952MCV 1,5/ 6-G-3,81 THT Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: SMD/THT1837476MCVDU 1,5/ 6-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: Soldering1832772MCVK 1,5/ 6-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: Mounting rail1827318SMC 1,5/ 6-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 6, mounting: SolderingAddressPHOENIX CONTACT GmbH & Co. KG Flachsmarktstr. 832825 BlombergGermanyPhone +49 5235 3 00Fax +49 5235 3 41200 Phoenix ContactTechnical modifications reserved;。
1J77镍铁软磁金
1J77镍铁软磁金郭瑜欣：❶❼❸-○❶❽❻-❽❼❻❸1J77软磁合金是一种在外磁场作用下容易磁化而去除外磁场后磁感应强度又基本小时的磁性合金。
所谓的软、指这些材料容易磁化，在磁性上表现“软”。
软磁合金分为低碳电工钢和阿姆科铁、硅钢片、镍铁软磁金、铁骨软磁合金、铁硅铝软磁合金等。
1J77化学成分化学成分：C(％): ≤0.15Cr(％): 12.0～16.0Mo(％): 1.50～2.50Ni(％): 38.0～42.0Co(％): —W(％): 3.50～4.50Al(％): 1.80～2.30Nb(％): —Fe(％): 余量Si(％)≤: 0.50Mn(％)≤: 0.50P(％)≤: 0.020S(％)≤: 0.015(％)--------------------------------------------------------------高磁导率软磁合金牌号：1J76 1J77 1J79 1J80 1J85 1J86规格：冷轧带材：0.03-0.10×180-250mm0.10-1.00×10-250 mm1.00-2.50×100-250 mm冷拉丝材：φ0.10-6.00 mm冷轧扁材： 4.50-20.0×50-250 mm热锻棒材：φ20.0-100.0 mm或方棒产品特点：具有高或极高的起始磁导率和DA磁导率、极低的矫顽力、较低的饱和磁感。
力学性能屈服强度（σs/MPa）: 735抗拉强度（σb/MPa）：735断后伸长率（δ5/%）：3电阻率：0.45 密度：8.2 居里点400规格为：板材，圆棒，线材，带材厚度:0.1mm以上直径:0.01mm以上宽度:按客户要求软磁合金应用：软磁合金的用途非常广泛。
因为它们容易磁化和退磁，而且具有很高的导磁率，可以起到很好的聚集磁力线的作用，所以软磁合金被广泛用来作为磁力线的通路，即用作导磁材料，例如变压器、传感器的铁芯，磁屏蔽罩，特殊磁路的轭铁、继电器、互感器、磁放大器、电磁离合器、汽车传感器等。
777.07资料
BUS IC DC/DC CONVERTER MOTOR DRIVER IC RIPPLE COUNTER80BLOCK DIAGRAMÿ Co-integrated pressure sensorFEATURESÿSupply voltage VDD 5VÿAmplified, calibrated, fully signal conditionedoutput of 4.0 VDC FS span (0.5 to 4.5V signal)ÿOutput ratiometric with supply voltageÿDigital Signal Processor for correction algorithmsÿMulti-order temperature compensation for gainand offsetÿFor gauge, differential, and absolute applicationsÿAdjustable output clampsÿProgrammable output filterÿEEPROM memory for End-of-line calibrationÿ– 40°C to + 125°C operating temperatureÿAvailable packages:ÿASIC plus: SO16w body with nozzleÿ bare dieÿ customer specificAPPLICATIONÿAutomotive pressure sensing(MAP, tire pressure, oil, fuel)ÿBarometric measurementÿMedical instrumentationÿIndustrialÿHVACDESCRIPTIONThe IC of OEM integrated pressure sensor combines state-of-the-art pressure sensor technology with signal conditioning toproduce a fully signal-conditioned, amplifi ed, temperature com-pensated sensor. The sensor utilizes a digital signal processor toallow multiorder linear correction to achieve increased accuracyover conventional amplifi ed pressure systems. The device is a co-integrated die. It is also available as an IC without the sensor andis therefore suitable for the use of a precision signal processor forseparate sensors.The system uses an on-chip EEPROM to store the calibration data.This allows the device to be calibrated end-of-line and so to com-pensate for packaging stress and/or parametric changes due tothe addition of protective gel. Sensor ID information can also bestored in the EEPROM.The chip is currently confi gured for operating pressure rangesfrom 350mbar FS up to 10bar (5PSI to 145PSI FS). For pressure rang-es below 350mbar (5PSI), the IC interfaces with an off-chip sensor.The range is extendable above 10bar.元器件交易网。
资产管理样例数据
领用单位号仪器编号分类号仪器名称型号规格单价国别国别码0300012000015105030402通用编程器RF810*850中国156兼容机PⅢ733/128M/30G9410中国156 0300012000083505010105微型电子计算机兼容机PⅢ733/128M/20G8180中国156 0300012000083605010105微型电子计算机0300012000083705010105微型电子计算机兼容机PⅢ733/128M/20G8100中国156 0300012001021605010562光盘刻录机HP-935032×10×42100美国840兼容机P42.8G/1G/129175中国156 0300012003177705010105微型电子计算机0300012004052505010508活动硬盘池能40G1840中国156*1270.8中国156 0300012007078205010108计算机开发板ARMSYS44BO0300012007082005010539标准机柜* 1.5m1100中国156 0300012007082105010539标准机柜* 1.5m1100中国156 0300012007082205010539标准机柜* 1.5m1100中国156 0300012007082305010539标准机柜* 1.5m1100中国156 0300012007082405010539标准机柜* 1.5m1100中国156 0300012007082505010539标准机柜* 1.5m1100中国156 0300012007082605010539标准机柜* 1.5m1100中国156 0300012007082705010539标准机柜* 1.5m1100中国156 0300012007082805010539标准机柜* 1.5m1100中国156 0300012007082905010539标准机柜* 1.5m1100中国156 0300012007083005010539标准机柜* 1.5m1100中国156 0300012007083105010539标准机柜* 1.5m1100中国156 0300012007083205010539标准机柜* 1.5m1100中国156 0300012007083305010539标准机柜* 1.5m1100中国156 0300012007083405010539标准机柜* 1.5m1100中国156 0300012007083505010539标准机柜* 1.5m1100中国156 0300012007083605010539标准机柜* 1.5m1100中国156 0300012007083705010539标准机柜* 1.5m1100中国156 0300012007083805010539标准机柜*1*0.6*21820中国156 0300012007083905010539标准机柜*1*0.6*21820中国156 0300012007084005010539标准机柜*1*0.6*21820中国156 0300012007084105010539标准机柜*1*0.6*21820中国1564093中国156 0300012007096205010105微型电子计算机E400 17'LCD PE3.0G/intel9芯片组/512M DDRII/160GSATA/7100GS12厂家出厂号出厂日期购置日期附件数量附件总价现状管理级别领用人北京润正机电公2000.042000.0400B E倪晓军南京新华海电脑2000.122000.1200B D倪晓军南京新华海电脑2000.122000.1200B D倪晓军南京新华海电脑2000.122000.1200B D倪晓军惠普公司2001.032001.0300B E倪晓军南京润佳公司2003.112003.1100B D倪晓军无2004.062004.0600B倪晓军杭州市宇泰电子2007.052007.0500B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军无2007.062007.0600B倪晓军清华同方2007.072007.0700B倪晓军经费科目使用方向经手人变动日期使用单位号国标分类号资产类别入库时间科研号22倪晓军2007-7-310405697900062000-6-2799外1922倪晓军2007-7-31040871110506#########00外0822倪晓军2007-7-31040871110506#########00外0822倪晓军2007-7-31040871110506#########00外0822倪晓军2007-7-310403714900062001-5-2500外0822刘一凡2007-7-31040371110506#########03外1322倪晓军2007-7-310403712102062004-11-42004外1422倪晓军2007-7-310405711199062007-6-1207004063311倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405714900062007-6-1407J0211倪晓军2007-7-310405711105062007-7-31中央地方共建/07广02设备号单据号记帐人字符字段1字符字段2字符字段3数字字段1数字字段2审核21100TRUE555,01/300TRUE555,01/62800TRUE55500TRUE14700TRUE03/57400TRUE04/22900FALSE07/27200TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32700TRUE07/32900TRUE07/32900TRUE07/32900TRUE07/32900TRUE07/40702107133/71300TRUE序号标志清查方式清查日期清查异常财务审核财审核日期财务审核人审单人######### 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE################## 0 - -FALSE#########图片文件校区备注领用单位名仪器来源11 0计算机实验教学11 0计算机实验教学0计算机实验教学1111 0计算机实验教学11 0计算机实验教学11 0计算机实验教学11 0计算机实验教学11 0自购计算机实验教学0自选计算机实验教学1111 0自选计算机实验教学11 0自选计算机实验教学11 0自选计算机实验教学11 0自选计算机实验教学11 0自选计算机实验教学0自选计算机实验教学1111 0自选计算机实验教学0自选计算机实验教学1111 0自选计算机实验教学11 0自选计算机实验教学11 0自选计算机实验教学11 0自选计算机实验教学11 0自选计算机实验教学0自选计算机实验教学1111 0自选计算机实验教学11 0自选计算机实验教学11 0自选计算机实验教学11 0自选计算机实验教学11 0自选计算机实验教学0自选计算机实验教学1111 0自选计算机实验教学11 0计算机实验教学。
(完整word版)ISO7637-1中文
ISO7637-1前言ISO(国际标准化组织)是各国标准机构(ISO成员机构）的世界性联合会。
制定国际标准的工作通常通过ISO技术委员会进行。
对已成立技术委员会的主题感兴趣的每个成员机构都有权在该委员会中派代表。
与ISO联络的政府和非政府国际组织也参加了这项工作。
ISO与国际电工委员会（IEC）在电工标准化的所有事项上密切合作。
国际标准是根据ISO/IEC指令第3部分中给出的规则起草的。
技术委员会的主要任务是制定国际标准。
技术委员会通过的国际标准草案将分发给成员机构进行表决。
作为国际标准的出版需要至少75%的投票成员机构的批准。
请注意ISO 7637这一部分的某些要素可能是专利权的主体。
ISO不应对识别任何或所有此类专利权负责。
ISO 7637—1由技术委员会ISO/TC 22，道路车辆,小组委员会SC 3，电气和电子设备编写.此ISO 7637-1的第二版取消并取代了经过技术修订的ISO 7637-0:1990。
ISO 7637—1和ISO 7637—2的第一版（均于1990年出版）已合并为ISO 7637-2的第二版.ISO 7637由以下部分组成，一般标题为道路车辆-传导和耦合产生的电气干扰：-第1部分：定义和一般考虑事项-第2部分：仅沿供电线路进行电气瞬态传导—第3部分：额定12 V或24 V供电电压的车辆—通过电容式和电感耦合通过电源线以外的线路进行的电气瞬态传输。
引言在许多机动车设备的正常运行过程中会发生电气和射频干扰。
它们在很宽的频率范围内产生,并可以通过传导、耦合或辐射分发到机载电子设备和系统.近年来，越来越多的用于控制、监视和显示各种功能的电子设备被引入到车辆设计中.有必要考虑这些设备运行的电气和电磁环境，特别是车辆电气系统本身产生的干扰。
这种干扰可能导致电子设备的降级（暂时故障甚至永久损坏）。
此外,“最坏情况”通常是由例如点火系统、发电机和交流发电机系统、电动机和执行器在车辆内部产生的干扰所导致的情况。
jis c 7021 (1977)a-4 标准文件
jis c 7021 (1977)a-4 标准文件下载温馨提示:该文档是我店铺精心编制而成，希望大家下载以后，能够帮助大家解决实际的问题。
文档下载后可定制随意修改，请根据实际需要进行相应的调整和使用，谢谢!并且，本店铺为大家提供各种各样类型的实用资料，如教育随笔、日记赏析、句子摘抄、古诗大全、经典美文、话题作文、工作总结、词语解析、文案摘录、其他资料等等，如想了解不同资料格式和写法，敬请关注!Download tips: This document is carefully compiled by theeditor.I hope that after you download them,they can help yousolve practical problems. The document can be customized andmodified after downloading,please adjust and use it according toactual needs, thank you!In addition, our shop provides you with various types ofpractical materials,such as educational essays, diaryappreciation,sentence excerpts,ancient poems,classic articles,topic composition,work summary,word parsing,copy excerpts,other materials and so on,want to know different data formats andwriting methods,please pay attention!JIS C 7021 (1977) A-4：半导体分立器件环境与耐久性测试标准详解JIS C 7021是日本工业标准委员会（Japanese Industrial Standards Committee）发布的一系列标准，旨在规定半导体分立器件的环境试验和耐久性评估方法。
CW-QP7
5.0相关文件
5.1《生产计划与物料控制程序》
5.2〈〈产品标识和可追溯性控制程序〉〉
6.0相关记录
6.1《装箱单》
6.2《物料卡》
6.3《出货计划表》
4.1.3使用叉车、手推车时注意保护好车上物品,务必轻拿轻放,车速缓慢。
4.1.4搬运人员应接受相应的培训。
4.1.5物品搬运前应先核对品名、规格、数量是否正确。
4.1.6物品应摆放在规定位置上。
4.2储存、防护
4.2.1仓管员负责所有在库物料的储存工作,生产部门内的产品由其工序组长负责相应的储存、防护工作。
c）仓库对在库物料每月末盘点,对长期库存十二个月以上的货品通知品质部进行定期检查,合格的继续保存,不合格品申请报废处理。
4.3出库状况,制作并打印《装箱单》。
4.3.2成品仓管根据《装箱单》,负责现场核证,标签、数量、客户名称、订单号等是否相符。
4.3.3出货时,成品仓管监督出货装车人员按《装箱单》上之明细,将货物搬运装车,运输过程中要防止碰撞、挤压,以免使货物变形、划伤。
4.2.2在库物料（如原材料、纸箱、成品等）按下述原则保管:
a）所属物料应置于指定位置,且有相应的保护物品（如隔板、保护膜等）。
b）不同物料分类摆放,贴上相应标签。
c）入库之成品,应置于规定区域,标识清楚。
d）所有在库物料须填写《物料卡》做到帐、物、卡相符(原材料与成品除外)。
4.2.3在制造过程中的物料生产部门负责以卡板、或纸箱、等放置,并作必要标识。
编制:
xxx
审核:
批准:
分发号:
修订情况
版次
日期
状态
描述
Fluke 4271782 True-rms 数字多功能仪用户手册说明书
PN 4271782August 2012© 2012 Fluke Corporation. All rights reserved.All product names are trademarks of their respective companies.287/289True-rms Digital MultimetersSafety InformationGo to to register your product and find more information.A Warning identifies conditions and procedures that are dangerous to the user.WarningTo prevent possible electrical shock, fire, or personalinjury:•Read “Safety Information” before using this Meter. • Use this Meter only as specified in this manual or the protection provided by the Meter might beimpaired.• Do not use the Meter if it is damaged. Before you use the Meter, inspect the case. Look for cracksor missing plastic. Pay particular attention to theinsulation surrounding the connectors.• Make sure the battery door is closed and latched before operating the Meter.• Remove test leads from the Meter before opening the battery door.• Inspect the test leads for damaged insulation orexposed metal. Check the test leads forcontinuity. Replace damaged test leads beforeyou use the Meter.• Do not apply more than the rated voltage, as marked on the Meter, between the terminals orbetween any terminal and earth ground.• Never operate the Meter with the cover removed or the case open.• Use caution when working with voltages above 30 V ac rms, 42 V ac peak, or 60 V dc. These voltagespose a shock hazard.• Use only the replacement fuses specified by the manual.• Use the proper terminals, function, and range for measurements.•Avoid working alone.•When measuring current, turn off circuit power before connecting the Meter in the circuit.Remember to place the Meter in series with thecircuit.•When making electrical connections, connect the common test lead before connecting the live testlead; when disconnecting, disconnect the live test lead before disconnecting the common test lead. •Do not use the Meter if it operates abnormally.Protection may be impaired. When in doubt, havethe Meter serviced.•Do not operate the Meter around explosive gas, vapor, or dust.•Use only 1.5 V AA batteries, properly installed in the Meter case, to power the Meter.•When servicing the Meter, use only specified replacement parts.•When using probes, keep fingers behind the finger guards on the probes.•Do not use the Low Pass Filter option to verify the presence of hazardous voltages. Voltages greaterthan what is indicated may be present. First, makea voltage measurement without the filter to detectthe possible presence of hazardous voltage. Then select the filter function.•Only use test leads that have the same voltage, category, and amperage ratings as the meter andthat have been approved by a safety agency. •Use proper protective equipment, as required by local or national authorities when working inhazardous areas.•Comply with local and national safetyrequirements when working in hazardouslocations.•To avoid circuit damage and possibly blowing the Meter’s current fuse, do not place the probesacross (in parallel with) a powered circuit when alead is plugged into a current terminal. Thiscauses a short circuit because the resistancethrough the Meter's current terminals is very low. •To avoid possible electric shock or personal injury, do not use the Low Pass Filter option toverify the presence of hazardous voltages.Voltages greater than what is indicated may bepresent. First, make a voltage measurementwithout the filter to detect the possible presenceof hazardous voltage. Then select the filterfunction.•To avoid the potential for fire or electric shock, do not connect the thermocouple to electrically livecircuits.•To avoid damage to the Meter and possible injury, never attempt an in-circuit current measurementwhere the open-circuit potential to earth is greaterthan 1000 V.•To avoid electrical shock or personal injury,repairs or servicing not covered in this manualshould be performed only by qualified personnelas described in the 287/289 Service Information.•To avoid electrical shock or personal injury,remove the test leads and any input signalsbefore replacing the battery or fuses. To preventdamage or injury, install only Fluke specifiedreplacement fuses with the amperage, voltage,and speed ratings shown in the User’s Manual.•Do not exceed the Measurement Category (CAT) rating of the lowest rated individual component ofa Product, probe, or accessory.•Do not use the TL175 or TP175 test probes in CAT III or CAT IV environments without the probe tipfully extended and correct category rating visiblein the window.•When the TL175 is used with instruments or other accessories, the lowest category rating of thecombination applies. One exception is when theprobe is used with the AC172 or AC175.Safety SpecificationsBattery Type: 6 AA Alkaline batteries, NEDA 15A IEC LR6 Temperature:Operating: -20 °C to +55 °CStorage: -40 °C to +60 °CAltitude: Operating: 3000 m; Storage: 10,000 mFrequency Overload Protection: Input is limited to the product of a V rms sinewave times frequency of 2 x 107 V-Hz.SymbolsSymbol Description Risk of Danger. Important information. SeeManual.Hazardous voltage.Battery (Low battery when shown on the display)BatteryUnderwriters Laboratory listed productFuseInspected and licensed by TÜV Product ServicesAC (Alternating Current or Voltage)DC (Direct Current or Voltage)Continuity test or continuity beeper toneConforms to European Union directivesConforms to relevant North American SafetyStandards.Conforms to relevant Australian EMC requirements FuseCAT II Measurement Category II is applicable to test and measuring circuits connected directly to utilization points (socket outlets and similar points) of the low-voltage MAINS installation.CAT III Measurement Category III is applicable to test and measuring circuits connected to the distribution part of the building’s low-voltage MAINS installation.CAT IV Measurement Category IV is applicable to test and measuring circuits connected at the source of the building’s low-voltage MAINS installation.Double InsulationThis product complies with the WEEE Directive (2002/96/EC) marking requirements. The affixed label indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE Directive Annex I, this product is classed as category 9 "Monitoring and Control Instrumentation" product. Do not dispose of this product as unsorted municipal waste. Go to Fluke’s website for recycling information.Lifetime Limited WarrantyEach Fluke 20, 70, 80, 170, 180 and 280 Series DMM will be freefrom defects in material and workmanship for its lifetime. As usedherein, “lifetime” is defined as seven years after Flukediscontinues manufacturing the product, but the warranty periodshall be at least ten years from the date of purchase. Thiswarranty does not cover fuses, disposable batteries, damage fromneglect, misuse, contamination, alteration, accident or abnormalconditions of operation or handling, including failures caused byuse outside of the product’s specifications, or normal wear andtear of mechanical components. This warranty covers the originalpurchaser only and is not transferable.For ten years from the date of purchase, this warranty also coversthe LCD. Thereafter, for the lifetime of the DMM, Fluke willreplace the LCD for a fee based on then current componentacquisition costs.To establish original ownership and prove date of purchase,please complete and return the registration card accompanyingthe product, or register your product on .Fluke will, at its option, repair at no charge, replace or refund thepurchase price of a defective product purchased through a Flukeauthorized sales outlet and at the applicable international price.Fluke reserves the right to charge for importation costs ofrepair/replacement parts if the product purchased in one countryis sent for repair elsewhere.If the product is defective, contact your nearest Fluke authorizedservice center to obtain return authorization information, thensend the product to that service center, with a description of thedifficulty, postage and insurance prepaid (FOB Destination). Flukeassumes no risk for damage in transit. Fluke will pay returntransportation for product repaired or replaced in-warranty. Beforemaking any non-warranty repair, Fluke will estimate cost andobtain authorization, then invoice you for repair and returntransportation.THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULARPURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE SHALLNOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTALOR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDINGLOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY. AUTHORIZED RESELLERS ARE NOT AUTHORIZED TOEXTEND ANY DIFFERENT WARRANTY ON FLUKE’S BEHALF.Since some states do not allow the exclusion or limitation of animplied warranty or of incidental or consequential damages, thislimitation of liability may not apply to you. If any provision of thiswarranty is held invalid or unenforceable by a court or otherdecision-maker of competent jurisdiction, such holding will notaffect the validity or enforceability of any other provision.Fluke Corporation Fluke Europe B.V.P.O. Box 9090 P.O. Box 1186Everett, WA 98206-9090 5602 BD EindhovenU.S.A. TheNetherlands 6/07。
EN1677-1标准
目录前言 (2)0简介 (3)1.使用范围 (3)2.标准参考文献 (4)3．术语及定义 (6)4﹑失效 (7)5.安全要求 (8)6.安全要求验证 (12)7.标注 (16)8. 制造商证书 (17)9.使用说明 (17)附录A：机械性能计算 (18)附录B：8级锻钢件的命名原则 (19)附录ZA (20)前言该欧盟标准关于链条﹑钢索﹑带材﹑吊索及配件的安全性由“ CEN/TC168”技术委员会筹备制定,秘书处设在英国标准协会（BSI）。
欧盟标准被赋予了国家标准的法律效力，至少在2001年2月之前应成文发布或认可，与国标相冲突的部分最迟到2001年2月之前应被取消。
该欧盟标准已由欧盟委员会和欧洲自由贸易协会委托CEN筹备制定，并与EU指南相一致。
与EU指南相联系的部分见本标准中的附录ZA。
EN1677标准中的其它吊索组件：2：锻钢8级安全吊钩。
3：锻钢 8级自锁吊钩。
4： 8级链环。
5：锻钢 4级安全吊钩。
6： 4级链环。
该欧盟标准的附录A和附录B是必要的补充。
根据CEN/CENELEC内部规则，以下国家的国家标准机构执行该欧盟标准：奥地利﹑比利时﹑捷克共和国﹑丹麦﹑芬兰﹑法国﹑德国﹑希腊﹑冰岛﹑爱尔兰﹑意大利﹑卢森堡﹑荷兰﹑挪威﹑葡萄牙﹑波兰﹑西班牙﹑瑞典﹑瑞士﹑英国。
0简介欧盟标准是为适应机械指南和欧洲自由贸易组织规则的安全要求而制定的标准。
本标准规定的链环是吊索的一部分，但其同样可作其它用途，因此，链环的失效程度在使用范围中有详细的说明，此外，起吊装置应符合EN292中失效程度的规定，该标准并未包含在EN1677中。
1.使用范围本标准对锻钢8级组件（可达13TWLL）作了详细的规定，主要使用在-----EN818-4规定的链式吊索。
-----PREN13414-1:1999规定的编织带吊索-----EN1492-2:2000中规定的编织带吊索主要用于提升物体，原材料，货物。
本标准不适用于手工锻打件，焊接链环，或其它焊接件。
TI427C 07 en 12.08 荷尔士水质监测仪说明书
TI427C/07/en/12.0871085624Technical InformationISEmax CAM40/CAS40Online measurement of nutrient parametersIon-selective electrode system for the continuous measurement ofammonium and nitrateApplicationThe ion-selective electrode system works directly in the activated sludge basin of the sewage treatment plant without any sample conditioning or sample transportation.The system consists of a sensor, electrodes and a transmitter with display and operating elements and is mounted on the basin rim.Up to two ion-selective sensors simultaneously measure nitrate and ammonium in the activated sludge basin.Your benefits•Reliable and cost-saving:–Nitrate and ammonium measured directly without the need for expensive sample conditioning–Optional potassium and/or chloride measurement to compensate high concentrations of interference ions –Low operating costs since no reagent used •Versatile and flexible:–Large measuring range 0.1-1000 mg/l NH 4-N or 0.1-1000mg/l NO 3-N–4 current outputs and 5 relays, some user-configurable •Easy-to-use and safe:–Installed directly on the basin rim, no measuring container or sample-conveying pump required–Low maintenance thanks to compressed air cleaning –Membrane cap replacement every 6 months prolongs electrode service lifeISEmax CAM40/CAS402Endress+HauserMeasuring systemMeasuring principleAt the heart of the ion-selective electrode (ISE) is a membrane that is selective for the ion to be measured.An ionophore is integrated into the membrane which facilitates the selective "migration" of a specific type of ion (e.g. ammonium or nitrate) to the electrode.As a result of the ion migration, a change in the charge occurs, causing an electrochemical potential that is proportional to the ion concentration. The potential is measured against a reference electrode with a constant potential and converted to a substance-specific concentration using the Nernst equation.With the potentiometric measuring principle, the color and turbidity do not affect the measurement result.InterferenceDepending on the selectivity of the ion-selective electrode vis-à-vis other ions (interference ions), and the concentration of these ions, such ions could also be interpreted as part of the measuring signal and thus cause measuring errors.When measuring in wastewater, the potassium ion which is chemically similar to the ammonium ion can cause higher measured values.The measured values for nitrate can be too high due to high concentrations of chloride.To reduce measuring errors resulting from such cross-interference, the concentration of the potassium or chloride interference ion can be measured and compensated for with a suitable additional electrode.Measuring systemA complete measuring system comprises:•CAM40 transmitter •CAS40 sensor–Ion-selective electrode(s) for ammonium and/or nitrate –Reference electrode–Ion-selective electrode for compensating cross-interference –pH glass electrodeOptional•Upright post with boom •Wall retainer•Weather protection cover - absolutely essential if mounting the transmitter outdoors!•Compressed air generator (if no compressed air is available on site)General measuring principle of an ion-selective electrodeA B 12345Reference electrode Ion-selective electrode Inner metal lead Bridging electrolyte JunctionInner electrolyteIon-selective membraneISEmax CAM40/CAS40Endress+Hauser 3InputMeasured variablesDepending on version:•Ammonium •Nitrate •Potassium •Chloride •pH valueMeasuring ranges•Ammonium:0.1 to 1000 mg/l (NH 4-N)•Nitrate:0.1 to 1000 mg/l (NO 3-N)•Potassium:1 to 1000 mg/l •Chloride:1 to 1000 mg/lExample: measuring system on basin rim 12CAM40 transmitter Upright post with weatherprotection cover34CAS40 sensorCompressed air supply (cleaning)ISEmax CAM40/CAS404Endress+HauserOutputOutput signal 4 x 0/4 to 20 mA, galvanically isolatedSignal on alarm Signal follows the measured value, fault can be freely programmed to a relay Load Max. 500 ΩRelay output5 relays:All user-configurableIf the optional compressor is used, a relay output is used to control it.Switch outputRelay switching capacity:230 V DC / 5 APower supplyElectrical connectionSupply voltage 100 to 240 V ACCaution!The power supply must be connected via an all-pole mains switch.Cable specification 3-wire, shielded cable, 10 m (33 ft) standard lengthCaution!Cable must have an outer diameter of 5 to 13 mm (0.2 to 0.5 inch) to guarantee the specified type of protection at the cable glands.Electrode connection GSA socketISEmax CAM40/CAS40Endress+Hauser 5Performance characteristicsResponse time t 901)•Ammonium:< 2 min.•Nitrate:< 2 min.•Potassium:< 2 min.•Chloride:< 2 min.Measured value resolutionAmmonium, nitrate, potassium, chloride •0.1 to 99 mg/l:0.01 mg/l•99 to 999 mg/l:0.1 mg/l •> 999 mg/l:1 mg/lMaximum measured error ± 5 % of the measured value ± 0.2 mg/l Repeatability ±3 % of the display valueCompensationMax. operating lifeMembrane and electrolyte •Use:0.5 years •Storage:2 yearsAutomatic cleaning•Cleaning medium:Air•Pressure:3 to 3.5 bar (30 to 50 psi)•Volume of air required per cleaning cycle:3 to 4 l (0.8 to 1 US gal)•Cleaning duration:4 to 15 s•Cleaning intervals (at T > 10 °C (50 °F)):Sludge activation inlet: 15 s cleaning, 30 min pause Sludge activation: 15 s cleaning, 1 hour pause1) For a change between 0.5 and 1 mmol/l in both directions, at 25 °C (77 °F)Sensor TemperaturepH Potassium 1)1)The fluctuations in concentration, not the absolute value, are the determining factorChloride 1)Ammonium 2 to 40 °C (36 to 100 °F)pH 8.3 to 10 1 to 1000 mg/l (ppm)-Nitrate --10 to 1000 mg/l (ppm)Potassium ---Chloride ---ISEmax CAM40/CAS406Endress+HauserEnvironmentAmbient temperature rangeStorage temperatureProtection classProcessProcess temperature range 2 to 40 °C (36 to 100 °F)Process pressure 400 mbar (160 inH 2O) max. permitted overpressure pH value of the medium•Ammonium:pH 5 to 8.3 (without pH compensation)pH 5 to 10 (with pH compensation)•Nitrate:pH 2 to 12•Potassium:pH 2 to 12•Chloride:pH 1 to 10Mechanical constructionDimensionsCAM40Note!Please refer to the original drawing of the housing for other dimensions, such as that of the rear housing panel with the suspension grooves (--> pdf file on the CD for the BA).CAM40 transmitter:CAS40 sensor:-20 to 50 °C (-4 to 120 °F)2 to 50 °C (36 to 120 °F)CAM40 + CAS40:2 to 40 °C (36 to 100 °F)CAM40 transmitter:CAS40 sensor:IP 65IP 68CAM40 dimensionsISEmax CAM40/CAS40Endress+Hauser 7CAS40WeightMaterialElectrode process connectionPg 13.5CAS40 dimensionsCAM40 transmitter Approx. 2.6 kg (5.7 lbs)CAS40 sensor Approx. 2.8 kg (6.2 lbs)CAM40 transmitter:PolycarbonateCAS40 sensor:PVC, glass, polyethylene Wetted parts- Ammonium, nitrate, potassium electrode:- Chloride electrode:- Reference electrode:- pH electrode:PVC, plasticizer, silicone, nitrile PVC, AgCl, AgS, silicone, nitrile Glass, PTFE, EPDM Glass, EPDMISEmax CAM40/CAS408Endress+HauserHuman interfaceDisplay and operating elementsCertificates and approvals4 approvalDeclaration of conformityThe product meets the requirements of the harmonized European standards. It thus complies with the legal requirements of the EC directives.The manufacturer confirms successful testing of the product by affixing the 4 symbol.ISEmax CAM40 displayCall up the menu functions Measure + release the output signals Confirm, switch, scrollCall up calibration routines "Freeze" (hold) the output signalsTrigger manual cleaningISEmax CAM40/CAS40Endress+Hauser 9Ordering informationCAM40 product structureCAS40 product structureScope of deliveryThe scope of delivery comprises:•1 transmitter•1 sensor (version as per nameplate)•1 sensor cable•3 screws for fastening to the weather protection cover •1 set of Brief Operating Instructions•1 set of Operating Instructions on CD-ROMPower supplyA100 - 240 VAC; 50/60 HzSignal output14 x 0/4 - 20 mA CAM40-Complete order codeApplicationA Aeration basin, nitrification, denitrification, with reference electrode BInlet aeration basin, with pH compensation (only ammonium)Ion-selective parameter1Ammonium + nitrate 2Ammonium 3NitrateCompensation electrodeA NoneB Potassium (Ion-selective parameter="1" or "2" only)CChloride (Ion-selective parameter="1" or "3" only)Cable length110 m (33 ft)9Special version, to be specified CAS40-Complete order codeISEmax CAM40/CAS4010Endress+HauserAccessoriesNote!In the following sections, you find the accessories available at the time of issue of this documentation.For information on accessories that are not listed here, please contact your local service.Installation accessoriesImmersion assembly holder CYH101•For pH, ORP, oxygen, conductivity assemblies, for oxygen and turbidity sensors and for ISEmax;•With weather protection cover•Ordering acc. to product structure (Technical Information TI092C/07/en)a0010133Immersion assembly holder CYH101CYY102 universal post•Square pipe for mounting transmitters •Material: stainless steel 1.4301 (AISI 304)•Order No. CYY102-ASquare postISEmax CAM40/CAS40CYY101 weather protection cover for field devices, absolutely essential if operating the unit outdoors•Material: stainless steel 1.4031 (AISI 304)•Order No. CYY101-AWeather protection cover for field devicesMaintenance kits Membrane kit•2 membrane caps•Electrolyte•Order numbers:–Ammonium: 71072574–Nitrate: 71072575–Potassium: 71072576Maintenance kit for the chloride electrode•Sandpaper•Electrolyte•Order number: 71085727Electrodes Ion-selective electrode•Electrode, complete•Order numbers:–Ammonium: 71072578–Nitrate: 71072580–Potassium: 71072581–Chloride: 71072582–pH: CPS64-1AA2GSAReference electrode•Order number: CPS13-0TA2GSAStandard solution Ammonium, nitrate, potassium and chlorideStandard solution1Ammonium nitrate, 1 molar2Potassium chloride, 1 molarContainer sizeA250 ml (8.45 fl.oz.)Transport documents1Standard documents2Incl. dangerous goods sheets3Safety data sheetCertificateA NoneB Manufacturer's certificateCAY40-Complete order codepHHigh-quality buffer solutions of Endress+Hauser - CPY20Endress+Hauser11ISEmax CAM40/CAS40The secondary buffer solutions have been referenced to primary reference material of the PTB (German FederalPhysico-technical Institute) and to standard reference material of NIST (National Institute of Standards andTechnology) according to DIN 19266 by a DKD (German Calibration Service) accredited laboratory.pH valueA pH 2.00 (accuracy ± 0.02 pH)C pH 4.00 (accuracy ± 0.02 pH)E pH 7.00 (accuracy ± 0.02 pH)G pH 9.00 (accuracy ± 0.02 pH)I pH 9.20 (accuracy ± 0.02 pH)K pH 10.00 (accuracy ± 0.05 pH)M pH 12.00 (accuracy ± 0.05 pH)Quantity0120 x 18 ml (0.68 fl.oz) only buffer solutions pH 4.00 and 7.0002250 ml (8.45 fl.oz)101000 ml (0.26 US gal)505000 ml (1.32 US gal) canister for Topcal SCertificatesA Buffer analysis certificateVersion1StandardCPY20-complete order codeCleaning unit Caution!•Not suitable for continuous operation!Operating interval: max. 3 minutes cleaning, break for at least six times the cleaning time.•Avoid condensation in the pressurized hoses.Cleaning unit in the housing•230 V, IP 65•Conveying rate at atmospheric pressure: 50 l/min (13.2 gal/min)•Power consumption: 240 W•Current consumption: 1.3 A•Overheating protection: Automatic switch off at T > 130 °C (266 °F)•Order no.: 7107258312Endress+HauserISEmax CAM40/CAS40Endress+Hauser 13a0010789Cleaning unit 1Housing 2Pump3Terminal strip with fuse 4Suction side5Compressed air supply (to the sensor)Instruments InternationalEndress+HauserInstruments International AG Kaegenstrasse24153ReinachSwitzerlandTel.+41617158100Fax+41617152500***************.comTI427C/07/en/12.08Printed in Germany / FM+SGML 6.0 / POD。
zmj-4377-13131
体会精巧构思
总结：
1、百合花被子是情节 的一部分，推动了情节 的发展。
2、百合花被子还和人 物性格有关系。
探究人物形象（一）
1、百合花被子是新媳妇的，从她借被和献 被这两个情节，你看到了新媳妇怎样的性格？
娴静 淳朴 善良
高洁
2、作者是运用什么描写手法刻画这一人物形 象的?
语言描写、肖像描写、动作描写
拓展题：
第一株百合的教导：“我们要
全心全意默默地开花，以花来 证明自己的存在。” 给你带来了什么样的启迪？
人的一生中，挫折和失败是在所难 免的。只要心中有了目标，并且矢志不 移的朝着目标奋进，相信成功总会青睐 于你！
即使你摇不动树上的枝叶，你也不 要沮丧，只要真诚拥抱，终会得到意外 的风华；即使你激不起的水中的涟漪， 你也不要哭泣，只要勇敢的挥洒，终会 擎起一簇洁白的浪花；即使通向成功的 路上没有绿灯，你也不要失望，只要不 停的努力，终会为你开启一扇成功的大
5
讪讪： 难为情的样子。
6、虔诚： 恭敬有诚意。
思考题:
如此美丽的百合花，她生长的环
境好吗？请在原文中找一找。
自然环境 “偏僻遥远”、“断崖” 生存环境的艰险
舆论环境“不屑”、“嘲笑”、“讥讽” 鄙夷和不屑
百合花的内心独白：
在它的内心深处，有一个纯 洁的念头：“我是一株百合， 不是一株野草。唯一能证明 我是百合的办法，就是开出 美丽的花朵。”
结合百合花的种种言行， 你能发现她外表以外的美丽 吗？
百合在这样的环境下，付出
了如此大的努力，百合开的 花不但是外在美，而且是内 在灵魂贵而纯洁高尚的表现。
文章写了哪几个人物？围绕这些 人物写了哪几件事？
批
EX-07 08 017 8281(中文) 新版
產品名稱：
8281
產品型態：
混合物
製造商名稱:
HERNONASIAPTE.LTD
供應商名稱
HERNON MANUFACTURING INC.
供應商地址：
121 Tech DriveSanford,Florida32771USA
聯絡電話及傳真
電話:407-322 4000傳真:407-321 9700
2.成分辨識資料
中英文名稱
壓克力樹脂
65–75%
水
25–35 %
3.危害辨識資料
最重要的危害與效應
健康危害效應
環境影響
流到河川時由於乳液中的樹脂之粘著會造成呼吸困難,有時魚類會死亡。
物理性及化學性危害
。
特殊危害
主要症狀
物品危害分類
4.急救措施
食入
以水在口中漱乾淨,馬上送醫就診。並使其嘔吐出
吸入
馬上將患者移到空氣流通新鮮處,使其安靜,保溫之,盡速送醫就診。
皮膚接觸
擦去附著物,用水和肥皂清洗,若有發癢,發炎等症狀時,送醫就診。
眼睛接觸
用乾淨的水,洗15分鐘以上後,送眼科醫師治療
最重要症狀及危害效應：
對急救人員之防護：
防護面具、N95口罩
對醫師之提示：
若有誤食，考慮給予洗胃
5.滅火措施
適用滅火劑:
水強化液泡粉末
特殊滅火程序:
切斷附近的著火源,在上風處滅火。
急毒性
吸入
皮膚
眼睛
食入
局部效應：
致敏感性：
與皮膚接觸後放置不處理的話,有時會引起發炎.如吸入蒸氣時,有時會有引起頭痛.
慢毒性或長期毒性
特殊效應
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
42777-1 Product Details
Home | Customer Support | Suppliers | Site Map | Privacy Policy | Browser Support
© 2008 Tyco Electronics Corporation All Rights Reserved Search
Products Documentation Resources My Account Customer Support Home > Products > By Type > Product Feature Selector > Product Details
42777-1
Active Splices - Open Barrel
Always EU RoHS/ELV Compliant (Statement of Compliance)
Product Highlights:
?Splice
?Non-Insulation Support
?Wire/Cable Type = Magnet Wire
?Wire Range = 0.30-1.50²[22-15.5]
mm [AWG]
?With Serrations
View all Features | Find Similar
Products
Check Pricing &
Availability
Search for Tooling
Product Feature
Selector
Contact Us About
This Product
Quick Links
Documentation & Additional Information
Product Drawings:
?AMPLIVAR SPLICE 5 SERRATIONS AMPLIVAR 5 RANURAS (600...
(PDF, English)
Catalog Pages/Data Sheets:
?None Available
Product Specifications:
?None Available
Application Specifications:
?AMPLIVAR 5 Serration Pigtail Splice(PDF, English)
Instruction Sheets:
?None Available
CAD Files:
?None Available
List all Documents Additional Information:
?Product Line Information
Related Products:
?Tooling
Product Features (Please use the Product Drawing for all design activity)
Product Type Features:
?Product Type = Splice
?Insulation Support = Non-Insulation Support ?Wire/Cable Type = Magnet Wire
?Serrations = With Serrations
?Number of Serrations = 5
?Splicing Type = Pigtail
?Strip Type = End Feed
?Material = Brass
?Finish = None
?Proprietary Name = AMPLIVAR
?Comment = For magnet wires > 0.4 mm
diameter Body Related Features:
?Wire Range (mm [AWG]) = 0.30-1.50²[22-
15.5]
?Stock Thickness (mm [in]) = 0.50 [0.019] Industry Standards:
?RoHS/ELV Compliance = RoHS compliant, ELV
compliant
?Lead Free Solder Processes = Not relevant for
lead free process
?RoHS/ELV Compliance History = Always was
RoHS compliant
Packaging Related Features:
?Packaging Method = Strip
Other:
?Brand = AMP
Provide Website Feedback | Contact Customer Support。