Android 移动终端测试规范

6 CDMA1x Requires of terminal6.2.3 TC-BasicReq-02003 [Required]Packet Data bearer and per set parameterTesting Number: TC-BasicReq-02003Testing Level: RequiredTesting Purpose: Check up Circuit Model Data Load Business of the terminal whether accord with the specification requirementsTesting equipment: nullTesting material: nullTechnical Parameters:P4 Former Reverse Grouping Data RateP5 3GPP2 C.S0017 versionPreset conditions 1) Network is available.Testing Steps :1) Look up technical parameter specification of the terminal,get Former Reverse Grouping Data Rate of the terminal supported, version serial and parameter value Of 3GPP2 C.S0017.2) Check terminal whether support forward peak rate value 153.6kbps, Reverse rate peak value 153.6kbps,and record what business under WAP/WWW, MMS, Java, Streaming media,Email. supported by terminal.3) Check up whether the version number 3GPP2 C.S0017 of terminal support is 3GPP2C.S0017-0-2 v2.0 or 3GPP2 C.S0017-0-1.4) Check the terminal whether has been given Link Parameter Groups of PPP as below：P PP Link1：China telecom WAP setting CTWAP（Display name by Chinese）/CTWAP （Display name by English）PPP Call number：#777PPP Authentication Mode：CHAP/PAP(priority for CHAP)PPP User Name：ctwap@PPP Password：vnet.mobiP PP Link2：China telecom Internet Settings CTNET（Display by Chinese）/CTNET（Display by English）PPP Call number：#777PPP Authentication Mode：CHAP/PAP(priority for CHAP)PPP User Name：ctnet@PPP Password：vnet.mobi5) Check up a group of parameters of PPP Link whether including the parameter as below:（It‟s no need to match each words, just show that means ）D isplay name of parameter group（Connection name）D ata bearer mode（Data bearer）：Packet dataA ccess point name（Access point name）P PP Call number（Prompt password）P PP Authentication Mode（Authentication）P PP User Name（User name）P PP Password（Password）.6) Look up technical parameter specification of the terminal, get and record OS name of terminal.7) For the terminals using intelligent operating system（Windows Mobile, WinCE, Android etc.）,Check up terminal whether allow users one-key access Link select interface of PPP in main form（Namely: unlock screen condition of standby interface）（this interface can implements switch between CTWAP and CTNET）,Check up whether it can disable data connection in this interface, set up a link of PPP :A（Name should be different from CTNET and CTWAP）,Check up current terminal whether show all Connecting parameter group name of PPP in this interface, and PPP has been given. Whether permit users modify Link Parameter of preset and default PPP Link.8) Set default PPP link as CTWAP in terminal, start up a application A（This application using CTNET connect to network）,Check whether the application can use normally. exit application A, Check up the default link of terminal whether still is CTWAP.9) Restore the factory default Settings in terminal, If you are not using intelligent operation system terminal（Windows Mobile, WinCE, Android etc.）,Check up terminal whether set “中国电信互联网设置CTNET” as default Network connection parameters, whether allow users set “中国电信WAP 设置CTWAP” as default Network connection parameters, otherwise, Check up the terminal whether set “中国电信WAP 设置CTWAP” as default Network connection parameters, whether allow users set “中国电信互联网设置CTNET” as default Network connection parametersExpected Results1) After step 2,The terminal support forward peak rate value153.6kbps,Reverse peak ratevalue153.6kbps.2) After step 3 3GPP2 C.S0017 of the terminal supported version is 3GPP2 C.S0017-0-2v2.0或3GPP2 C.S0017-0-1.3) After step 4,Terminal has been perset 2 groups of PPP connection parameters in “中国电信WAP设置CTWAP” and “中国电信互联网设置CTNET”.4) After step 5, A group of PPP Link Parameter in terminal includes all of the parameters as below：D isplay name of parameter groups（Connection name）D ata bearer mode（Data bearer）：Grouped dataA ccess point name（Access point name）P PP Call number（Prompt password）P PP Authentication Mode（Authentication）P PP User Name（User name）P PP Password（Password）.5) After step 7,set “中国电信互联网设置CTNET” as default Network Link Parameters in terminal, the terminal allow users one-key access default Link Select Interface of PPP in main form. （Namely: unlock screen condition of standby interface）（This interface can switch between CTWAP and CTNET）,This interface can disable data connection. set up a PPP link: A（The name is different from CTNET and CTWAP）,Terminal can show all of the link parameter names of PPP in this interface ,and PPP has been perset . Terminal allow users modify preset link parameter of PPP and default PPP link. 6) After step 8,After quit Application A, the default link of the terminal still is CTWAP.7) After step 9,set “中国电信WAP设置CTWAP” as default Network Link Parameters in terminal, allow users set “中国电信互联网设置CTNET” as default Network Link Parameters.Remark1)If you are not using intelligent operation system terminal, then step 7 is unnecessary to test,and will not included in the test result, But it should be recorded in the test remark.6.3 Value added service in CS domain6.3.1 TC-BasicReq-03001 [Required] Calling Number Identification Presentation（CNIP）/ Calling Number Identification Restriction（CNIR）Testing Number TC-BasicReq-03001Testing Level RequiredTesting Purpose Check up CNIP of the terminal and CNIR of the terminalTesting equipment nullTesting material: nullTechnical Parameters:Preset conditions1) Network is normal, and support CNIP and CNIR.2) Both of terminal, cooperative terminal are support CNIP/CNIR business.3) Both of terminal, cooperative terminal are set up using CNIP when calling.4) Boot the terminal with card(SIM /UIM)Testing Steps :1) cooperative terminal Initiate voice call to terminal.2) In condition of Caller ID has not been stored in phone book of terminal or phone book of UIM card, when terminal receive the call, Check up it whether can display caller Id in call reminder. 3) Store the caller ID in the terminal contacts, and repeat step 1,Check up the terminal whether can show corresponding name in call reminder.4) Store the caller ID in the contacts under UIM card of the terminal, and repeat step 1,Check up the terminal whether can show corresponding name in call reminder5) cooperative terminal set as CNIR, cooperative terminal Initiate voice call to terminal.6) When terminal receive the call, Check up terminal whether can not display caller Id .7) Terminal Initiate voice call to cooperative terminal ,Check up cooperative terminal whethercan display caller Id in call reminder .8) The terminal is set as CNIR.9) Repeat step 7,Check up cooperative terminal whether can not display Caller Id in Call reminder.Expected Results1) After step 2,The terminal can display Caller ID in Call reminder2) After step 3,The terminal can display the corresponding name in Call reminder.3) After step 4,The terminal can display the corresponding name in Call reminder.4) After step 6,The terminal can not display Caller ID.5) After step 7,cooperative terminal can display caller Id in call reminder .6) After step 9,cooperative terminal can not display caller Id in call reminder .Remark：1)If the terminal dose not support UIM card, then step 4 is unnecessary to test .and will notincluded in the test result, but it should be recorded in the test remark should be described in the test record.6.4 ON/OFF, Network Selection and Authentication6.4.1 TC-BasicReq-04001 [Required] Boot UpTesting Number TC-BasicReq-01008Testing Steps：3) After the successful completion of the self-checking, check up terminal whether can enter stand by mode, check up cooperative terminal whether can received Boot Up registered short message from terminal, check up content of short message whether include machine mode, ESN（if the terminal using MEID, then sent MEID of the terminal）,insert into IMSI of UIM card in this machine, and software version of the machine, check up content of the short message and information of the machine whether match exactly.5) Clean up the SMS box . and shutdown, during shutdown, cooperative terminal send5 normal short message and 5 long message (each long message include6 message of concatenations).6) Starting up terminal, check up whether it can receive 10 SMS by cooperative terminal ,And each content of SMS and content of original SMS are quite the same.Expected Results:3) After step 3,terminal be in standby state, cooperative terminal should receive Boot Up registered short message from terminal ,including mode of the terminal, ESN（if the terminalusing MEID, then sent MEID of the terminal）Insert into IMSI of UIM card in this machine, and software version of the machine, The content of the short message and information of the machine should match exactly .5) After step 6,terminal can receive 10 SMS by cooperative terminal ,each content of SMS and content of original SMS are quite the same, long SMS has been spliced in one, have not loss SMS section, have not messy code.6.4.5 TC-BasicReq-04005 [Required]Network selection mode, automatic network selectionTesting Number：TC-BasicReq-04005Testing Purpose：Verify whether the terminal can automatic selection network .Preset conditions：1) If the terminal is mode of card can not separate form the machine, PRL files stored in terminal, If the terminal is mode of separate card for the machine then PRL files stored in UIM card. Testing Steps：1) Boot up the terminal in CDMA network coverage area, Check up whether the terminal can automatic select network according to PRL files, and registration successful.Expected Results ：1) After step 1,the terminal should be automatic select network according to PRL files, and registration successful.6.4.6 TC-BasicReq-04006 [Required]AuthenticationTesting Number：TC-BasicReq-04006Testing Purpose：Verify authentication of terminal whether accord with regulatory requirements .Testing Steps：1) Boot up terminal at CDMA network coverage area, Check up terminal authenticated and enter into standby interface.2) Do MEID test on the meter ,Check up whether all test items passed：1) After step 1,terminal can through Authentication and enter into standby interface,2) After step 2,terminal passed all MEID test items on the meter.6.5 Basic call Function s6.5.1 TC-BasicReq-05001 [Required] Input number in stand by mode initiate voice call.Testing Number：TC-BasicReq-05001Technical parameters: P7 display the maximum number of input digits in standby mode Testing Steps：2) Check up terminal whether be able to input numbers, and initiate voice calls；3) Check up terminal whether can input 32 figures as a call number.4) Continue to input, To enter numbers reach maximum digits of input number in standby mode, then keep on enter 1 digits , Check up terminal whether hide the number about previews of input , thus, allow users to immediately see the number of its last input.5)Terminal and cooperative terminal proceed voice call , hang up after a while, check terminal whether display duration of call..6)Terminal restore factory default settings about call duration display, check up terminal whether Display duration of call after end of the conversation by default.Expected Results ：1) After step 2,terminal should be able to input number, and Initiate voice calls.2) After step 3,until it can input 32 figures Numbers as up call number.3) After step 4 ,terminal hide input number about previews of input and allow users to immediately see the number of its last input.4) After step 5,terminal. Display duration of call after end of the conversation by default. Remark ：1) If terminal dose not support user setting up the function that shows call duration after end of the conversation ,then step 7 is unnecessary to test, besides, And not included in the test results, but should be recorded in the remark about that test.6.5.5 TC-BasicReq-05010 [Required] Voice call and SMS are used together, receive SMS During Voice call.Testing Number：TC-BasicReq-05010Testing Purpose：Verify terminal whether support voice call and SMS can be used together. and received SMS whether accordance with the standard during voice call.Preset conditions：1) Both of terminal and cooperative terminal A,B are support voice call, SMS, configured related parameters.2) Network, voice call and SMS are available.Testing Steps：1) Establish phone connections between terminal and cooperative terminal A .and m aintains phone conversation.2) Cooperative terminal B send SMS to terminal.3) Check up the terminal whether can prompt in vibrant way or in sounding way at user‟s interface when a new message arrives.4) After finish call , check up the terminal whether can prompt and display new SMS at interface.Expected Results ：1) After step 3 , prompt a new message arrives at user interface.2) After step 4 , prompt a new message arrives at interface.Remark ：1)If the terminal prompt new message arrives in step 2. then step 4 can be optionally, besides, itshould be explained in the test record.6.6 Common User Interface6.6.1 TC-BasicReq-06001 [Required] The status bar iconTesting Number: TC-BasicReq-06001Testing Purpose：Verify whether icons of the terminal status bar accord with regulatory requirementsTesting material: S4 UIM card（set owner of MNC as others）Testing Steps:4) Insert UIM card（MCC set as code of other country）and starting up, check up status bar whether including icons as below:I nternational Roaming prompt base on PRL(Preferred Roaming List)5) Cooperative terminal send a SMS to terminal, check up status bar whether including icons asbelow:Unread SMS instructions6) WAP gateway send a WAP PUSH message to terminal, check up status bar whether includingicons as below:S MS notification of WAP PUSHExpected Results ：3) After step 3,status bar should include icon：WiFi,5) After step 5,status bar should include icon：Unread SMS instructions,6) After step 6,status bar should include icon：SMS inform instruction of WAP PUSH,6.6.2 TC-BasicReq-06002 [Required] Display the operator name in standby screenTesting Number: TC-BasicReq-06002Testing Steps:3) Change language of terminal screen into English language ,then check up operator‟s name whether are display appears as “China Telecom”.Expected Results:3) After step 3,operator‟s name are display appears as “China Telecom”.6.6.5 TC-BasicReq-06010 [Required] Key lock / The basic functions of the screen lockTesting Number: TC-BasicReq-06010Testing Purpose：Verify keys of the terminal.Testing Steps:6) Enable Key lock or screen lock, Terminal is in standby, Try press any key or touch screen, check up whether it prompt user that user‟s keyboard or user‟s screen is locked at interface. Expected Results:6) After step 6,the terminal prompt user that user‟s keyboard or user‟s screen is locked at interface. besides, prompt how to unlock.6.7 Text Input and Information Extraction6.7.1 TC-BasicReq-07001 [Required] Input methodTesting Number: TC-BasicReq-07001Technical Parameters : P8 supported input method in terminalTesting Steps:2) Check whether the terminal via a stroke input method for input . Record of all supported input methods.Expected Results:2) After 2,Terminal should through a kind of stroke input method for input,6.7.3 TC-BasicReq-07003 [Required] Input character（Basic Category）Testing Number: TC-BasicReq-07003Testing Purpose：Verify the terminal whether can input charactersTechnical Parameters: P4 Input Characters P38 input character setPreset Conditions1) Terminal should be able to input.Testing Steps:2) Check up whether the terminal can input：& $ # * % = - + ( ) ! / < > \ ? ` “ : … . ; { } [ ] _ @( A total of 28 characters）.3) Check up whether the terminal can input：￥×（）＾！《》｜？†“”：… ‟.,,～……(or …) dash, ellipsis, A total of 22 characters, and it‟s ok that ellipsis is ……,…or…,Expected Results:2) After step 2,：& $ # * % = - + ( ) ! / < > \ ? ` “ : … . ; { } [ ] _ @x（a total of 28 characters）,3) After step 3,Terminal should be able to input：￥×（）＾！《》｜？†“”：… ‟.,,～dash, ellipsis,A total of 22 characters, and it‟s ok that ellipsis is ……,…or… .。