常规厚膜片式固定电阻器
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
FEATURES
GENERAL CHIP FIXED RESISTOR
RoHS
TYPE DESIGNATION
Example
GENERAL CHIP FIXED RESISTOR
Miniature and light weight.
Suit for reflow and wave flow solder.Stable electrical capability,high reliability.
Low assembly cost,suit for automatic SMT equipment.Superior mechanical and frequency characteristics.
RoHS compliant
CONSTRUCTION AND DIMENSION
L
a
W
t
b
unit:mm
APPEARANCE
,
The surface of resistor is covered with Protective Coating which hard to fade,and the surface of coating should avoid unevenness.
The terminal part is covered equable ,the plating is hard to fade,and should avoid unevenness,flaw,pinhole and discoloration.
With a clear mark ,the resistor body is crack-free.
REFERENCE STANDARD
GB/T 5729-2003GB/T 9546-1995
DERATING CURVE
70
()
For resistors operated in ambient over 70,rated load (power rating or current rating)shall be derated
in accordance with the above figure.
100
755025Operating Temperature Range -55
125
Ambient temperature
(
)
P e r c e n t r a t e d l o a d
GENERAL CHIP FIXED RESISTOR
RATINGS
GENERAL CHIP FIXED RESISTOR
PACKAGING
Tape and reel
Paper taping
02010402
0603080512061210
Embossed taping
P P1
W F
E
A0B0
D0P0
D1
t
A0
K0
K0
B0
t
P P1
W
F
E
A
B
D0P0T
Remark:For0201type,T1refers to the hole depth of paper carrier tape,T refers to the thickness of the paper carrier tape.
Reel
GENERAL CHIP FIXED RESISTOR
D
M
W
T
Bulk case
PACKAGING QUANTITY
unit:mm
110
31
36
12
GENERAL CHIP FIXED RESISTOR
The Explanation For The Resistance Value Marking
IEC E-24E-96
IEC E-24E-96Series Resistance Cross-reference List
E-24E-24series
10n
unit1101001K10K100K1M10M
Table one
E-2410
E-24series:Express resistance value on the glass side with three digits,the first tow digits should be significant and the third one denote number of zeros.
Example
E-96
Example
0603E-96
For the dimension type of 0603,express the resistance value with three code,the first two digit code denote the resistance of E-96series,and the third code of letter denote the multiplier (see the table three and four ).
Example
R The decimal point should be expressed by .
R Example
The jumper should be expressed by 0
Example
02010402For the dimension type of 02010402,there is no mark on the glass side.
Example
IEC IEC E-24
For the
resistance which don't belong to IEC serial,use the resistance of IEC serial which is most close to the required resistance of non-IEC serial for replacement.
To get agreement by both party if there special requirement for the marking.
10K
100K
2M
5.6
10
E-96series:For the dimension type of 0805,1206,12102010,2512express the resistance value with four digits,the first three digits are significant figures and the fourth denotes the number of zeros.
,1812,