华为 S5720-EI交换机 详版彩页
S5710-52C-EI-AC交换机彩页
VLAN 特性
支持4K个VLAN 支持Guest VLAN、Voice VLAN 支持GVRP协议 支持MUX VLAN功能 支持基于MAC/协议/IP子网/策略/端口的VLAN 支持1:1和N:1 VLAN Mapping功能
4
S5710-52C-EI
项目
S5700-28C-EI/ S5700-28C-EI- S5700-52C-EI/
• 可插拔双电源，支持直流或者交流供电 • 包转发率：156Mpps • 交换容量：368Gbps
• 24个10/100/1000Base-T以太网端口，4个复用的千兆SFP Combo，4个10GE SFP+，上行支持8×10/100/1000BASE-T、 8×1000Base-X、2×10GE SFP+插卡
杰出的网流分析
• S5710-EI支持NetStream 网络流量分析功能。作为网络流量输出器，S5710-EI 根据用户配置，实时 采集指定的数据流量，通过标准的V5/V8/V9报文格式，将数据上送给网络流量收集器，这些数据 被进一步处理，可以实现动态报表生成、属性分析、流量异常告警等功能，帮助用户及时优化网 络结构、调整资源部署。
• 48个10/100/1000Base-T，4个10GE SFP+，上行支持 8×10/100/1000BASE-T、8×1000Base-X、2×10GE SFP+插卡
• 可插拔双电源，其中S5710-52C-PWR-EI-AC内置1个580W交流 电源，S5710-52C-PWR-EI支持直流或者交流供电
• 可插拔双电源，交流供电 • 支持PoE+ • 包转发率：138Mpps • 交换容量：256Gbps
• 24个10/100/1000Base-T以太网端口，4个复用的千兆SFP Combo，4个10GE SFP+，上行支持8×10/100/1000BASE-T、 8×1000Base-X、2×10GE SFP+插卡
华为S5700-LI交换机详版彩页
S5700-28X-LI-24S-AC S5700-28X-LI-24S-DC
• 24个千兆SFP端口，4个复用的10/100/1000Base-T Combo端 口，4个万兆SFP+端口
• 分交流供电和直流供电两种机型，支持RPS冗余电源 • 包转发率：96Mpps • 交换容量：256Gbps
S5700-28P-LI-BAT S5700-28P-LI-4AH
S5700-LI系列全千兆企业交换机
S5700-LI系列全千兆企业交换机
产品概述
S5700-LI精简型千兆以太网交换机系列（以下简称S5700-LI），是华为公司自主研发的绿色节能的以太 网交换机，提供灵活的全千兆接入以及万兆上行端口。该系列交换机基于新一代高性能硬件和华为公 司统一的VRP（VersatileRouting Platform）软件平台，具有创新AHM（Advanced Hibernation Management 高级休眠）节能，智能iStack堆叠，灵活的以太组网，多样的安全控制等特点，为用户提供绿色、易 管理、易扩展、低成本的千兆到桌面的解决方案。此外，华为公司针对一些特定的应用场景和客户需 求，定制开发了一些特色款型，以满足不同客户的需要。
• 24个10/100/1000Base-T以太网端口，4个万兆SFP+端口 • 交流供电，支持RPS冗余电源 • 支持PoE+ • 包转发率：96Mpps • 交换容量：256Gbps
S5700-52P-LI-AC S5700-52P-LI-DC
• 48个10/100/1000Base-T以太网端口，4个千兆SFP端口 • 分交流供电和直流供电两种机型，支持RPS冗余电源 • 包转发率：102Mpps • 交换容量：256Gbps
华为交换机5720EI server-type port 堆叠案例
端口使用
计划使用XG0/0/1~XG0/0/2两个接口启用聚合堆叠，这样堆叠后可以承载20G的业务量。 但是实际配置时发现，使用XG端口每4个为一组（例如，1～4为一组、5～8为一组，2～5不能作为一组，即每组最后一 个端口的编号为4的倍数），如果将每组内的任意一个接口配置为堆叠物理成员端口，则同组内的另外三个端口下的配置 将丢失，且不能作为普通的业务口来使用。接口组可以拆分使用，例如1口可以用做堆叠逻辑 stack-port 0/1 组，2口可以 用作堆叠逻辑 stack-port 0/2 组。 设备的stack-port 0/1必须连接邻设备的stack-port 0/2，否则堆叠组建不成功。
堆叠前，建议将交换机配置重置，因为在第一次操作时，两台交换机未清空配置，导致在堆叠后出现配置命令不显示， 但配置却生效等异常情况。
堆叠配置
两台S5720 EI堆叠配置：
第一台：
<5720-1> system-view [5720-1] interface stack-port 0/1 [5720-1] port interface XGigabitEthernet 0/0/1 enable [5720-1] interface stack-port 0/2 [5720-1] port interface XGigabitEthernet 0/0/2 enable [5720-1] quit [5720-1] stack slot 0 priority 200 [5720-1] quit <5720-1> save <5720-1> quit
堆叠线接法： 两条堆叠线以交叉方法接两台交换机的堆叠口，即A交换机的1口接B交换机的2口，A交换机的2口接B交换 机的1口。 当两台交换机的上述配置完成后，将所有交换机下电，再重启查看状态
华为企业交换机产品全家福
新品 新品
·可升级为敏捷交换机 ·支持随板AC、统一用户管理 功能 ·支持1.5G大缓存单板，1M ·支持 CSS2交换网硬件集群，集群系统主 控1+N备份 ·支持随板AC、统一用户管理功能 ·支持1.5G大缓存单板，3M FIB表项，1M MAC表项 ·支持硬件Eth-OAM、BFD ·整机支持576个10GE端口/96个40GE/24个 100GE端口 FIB（S9700）/512K FIB(S7700) 表项，1M MAC表项 ·支持CSS交换网硬件集群和业 务口集群 ·支持MPLS L2 VPN、L3 VPN ·支持硬件Eth-OAM、BFD ·支持Easy Operation，简易运 维
智能路由交换机
S7703 · 5个总槽位，3个业务槽位 · 双主控，电源备份，支持 PoE+ · 交换容量：1.92T/2.88T · 包转发率：576M/2160M S7706 · 8个总槽位，6个业务槽位 · 双主控，电源备份，支持 PoE+ · 交换容量：3.84T/7.68T · 包转发率：1152M/5760M S7712 · 14个总槽位，12个业务槽位 · 双主控，电源备份，支持 PoE+ · 交换容量：3.84T/13.44T · 包转发率：1344M/10080M
·支持iStack 智能堆叠 ·支持50ms 环网保护 协议SEP/ G.8032 ·支持Easy Operation， 简易运维
华为企业网络Sx7交换机系列产品全家福
千兆接入交换机S5700-LI
S5700-28X-LI-AC S5700-28X-LI-DC S5700-28X-PWR-LI-AC · 24千兆RJ45，4万兆SFP+ · 交流或直流供电 · 支持RPS供电 S5700-52X-LI-AC S5700-52X-LI-DC S5700-52X-PWR-LI-AC · 48千兆RJ45，4万兆SFP+ · 交流或直流供电 · 支持RPS供电 S5700-28X-LI-24S-AC S5700-28X-LI-24S-DC · 24 千兆SFP，4千兆RJ45 Combo，4万兆SFP+ · 交流或直流供电 · 支持RPS供电 S5700-28TP-LI-AC S5700-28TP-PWR-LI-AC S5701-28TP-PWR-LI-A由 交 换机
华为 S5720-EI系列交换机 产品彩页(V2R10)
华为 S5720-EI 系列交换机 产品彩页文档版本 1.0 发布日期2016/10/26华为技术有限公司版权所有© 华为技术有限公司2013。
保留一切权利。
非经本公司书面许可，任何单位和个人不得擅自摘抄、复制本文档内容的部分或全部，并不得以任何形式传播。
商标声明和其他华为商标均为华为技术有限公司的商标。
本文档提及的其他所有商标或注册商标，由各自的所有人拥有。
注意您购买的产品、服务或特性等应受华为公司商业合同和条款的约束，本文档中描述的全部或部分产品、服务或特性可能不在您的购买或使用范围之内。
除非合同另有约定，华为公司对本文档内容不做任何明示或默示的声明或保证。
由于产品版本升级或其他原因，本文档内容会不定期进行更新。
除非另有约定，本文档仅作为使用指导，本文档中的所有陈述、信息和建议不构成任何明示或暗示的担保。
华为技术有限公司地址：深圳市龙岗区坂田华为总部办公楼邮编：518129网址：客户服务邮箱：support@客户服务电话：400-830-2118前言产品概述S5720-EI下一代增强型千兆以太网交换机系列（以下简称S5720-EI），是华为公司自主研发的新一代千兆以太网交换机，提供灵活的全千兆光/电/Combo口接入以及增强的万兆上行端口扩展能力。
该系列交换机基于新一代高性能处理器和华为公司统一的VRP（Versatile Routing Platform）软件平台，提供更大的表项规格，更高的硬件处理能力，可集成无线控制器功能，可扩展支持MACSec功能，具备更加完善的业务处理能力，增强的安全控制，灵活的以太组网，成熟的IPv6特性，智能iStack堆叠，方便的运行维护等特点。
广泛应用于企业园区接入、汇聚，数据中心千兆接入等多种应用场景。
产品外观产品特性和优势轻松的运行维护•电源端口前置的款型可以满足300mm深的机柜放置，整台设备可以前面板单面维护，简化了运维，而且机柜的摆放更加灵活，可以灵活选择机柜靠墙放置或者机柜背靠背放置，满足客户机柜深度小、机房空间有限的需求，并为客户节省空间。
华为 S5720-EI交换机 详版彩页
S5720-EI系列下一代增强型千兆以太网交换机S5720-EI系列下一代增强型千兆以太网交换机产品概述S5720-EI下一代增强型千兆以太网交换机系列（以下简称S5720-EI），是华为公司自主研发的新一代千兆以太网交换机，提供灵活的全千兆光/电/Combo口接入以及增强的万兆上行端口扩展能力。
该系列交换机基于新一代高性能处理器和华为公司统一的VRP（Versatile Routing Platform）软件平台，提供更大的表项规格，更高的硬件处理能力，可集成无线控制器功能，可扩展支持MACSec功能，具备更加完善的业务处理能力，增强的安全控制，灵活的以太组网，成熟的IPv6特性，智能iStack堆叠，方便的运行维护等特点。
广泛应用于企业园区接入、汇聚，数据中心千兆接入等多种应用场景。
12S5720-56C-PWR-EI-AC S5720-56C-PWR-EI-AC1•48个10/100/1000Base-T以太网端口，4个万兆SFP+•一个扩展子卡插槽•PoE+•可插拔双电源，默认配置一个AC电源，其中S5720-56C-PWR-EI-AC支持交流或直流供电，S5720-56C-PWR-EI-AC1支持交流供电•交换容量：598Gbps•包转发率：252MppsS5720-56C-EI-48S-AC S5720-56C-EI-AC •48个千兆SFP，4个万兆SFP+•一个扩展子卡插槽•可插拔双电源，支持交流或直流供电，默认配置一个AC电源•交换容量：598Gbps•包转发率：252Mpps•48个10/100/1000Base-T以太网端口，4个万兆SFP+•一个扩展子卡插槽•可插拔双电源，支持交流或直流供电，默认配置一个AC电源•交换容量：598Gbps•包转发率：252Mpps•支持华为Easy Operation简易运维方案，提供新入网设备Zero-Touch 安装、故障设备更换免配置、USB开局、设备批量配置、批量远程升级等功能，便于安装、升级、业务发放和其他管理维护工作，降低了运维成本。
华为 S5720-EI系列交换机 核心网交换机产品彩页
S5720-56PC-EI-AC
华为 S5720-EI 系列交换机
3
产品特性和优势
轻松的运行维护
• 电源端口前置的款型可以满足 300mm 深的机柜放置，整台设备可以前面板单面维护，简化了 运维，而且机柜的摆放更加灵活，可以灵活选择机柜靠墙放置或者机柜背靠背放置，满足客户 机柜深度小、机房空间有限的需求，并为客户节省空间。 • 支持远程点灯功能，管理人员可以使用配置命令控制前面板 sys 灯在一段时间内快闪，从而可 以在机房中快速定位设备。 • 支持 SVF 超级虚拟交换网，SVF 方案创新实现将原来“核心/汇聚+接入交换机+AP”的网络架 构，虚拟化为一台设备进行管理，提供业界最简化的网络管理方案，简化设备管理，实现接入 交换机和无线 AP 的即插即用；业务配置模板化，在核心设备上配置后自动下发到接入设备， 实现集中管控，简化业务配置，灵活调整。S5720-EI 在 SVF 方案中支持作为 client 角色。 • 支持华为 Easy Operation 简易运维方案，提供新入网设备 Zero-Touch 安装、故障设备更换 免 配置、USB 开局、设备批量配置、批量远程升级等功能，便于安装、升级、业务发放和其他 管理维护工作，降低了运维成本。支持 SNMP v1/v2c/v3 、 CLI （命令行）、 Web 网管、 SSHv2.0 等多样化的管理和维护方式；支持 RMON、多日志主机、端口流量统计和网络质量分 析，便于网络优化和改造。 • TWAMP 双向主动测量协议，精确测量任意 IP 链路的性能，轻松获取整网 IP 性能，无须专用 探针器或专有协议。
S5720-56C-EI-48S-AC S5720-56C-EI-48S-DC
S5700系列交换机技术方案介绍
固定端 口
8个 10/100/1000Bas e-T，4个千兆 SFP，2个复用的 10/100/1000Bas
e-T Combo
24个 10/100/1000Base-T P系列：4个千兆SFP X系列：4个万兆 SFP+
24个千兆SFP，8个 48个
复用的
10/100/1000Base-T
10/100/1000Base-T P系列：4个千兆SFP
LI：表示简化版本 SI ：表示标准版本 EI ：表示增强版本 HI： 表示高级版本
PWR：支持POE供电 PD： 支持POE受电
P： 上行口为SFP模块 T： 上行口为RJ45模块 TP：支持Combo接口 C： 上行接口可选配 X： 上行口为固定万兆 Q： 上行口为固定40G 无： 无上行口
目录
*对于S6xxx以外系列，下行端口默认为电口，若全部是电口，则此字段省略(J段) *对于S6xxx系列，下行端口默认为光口，若全部是光口，则此字段省略(J段)（S6x20除外）
EI I
24S AC
J
K
AC：交流供电 DC：直流供电 BAT：含电池槽位
24S：下行光口数 * 24T：下行电口数 *
48CS：CSFP接口数
华为S系列交换机（盒式）命名规则
HUAWEI S 5 7 00 S 28 TP PWR A BC D E F G H
S:交换机系列
6：下行万兆 5：下行千兆 3：三层下行百兆 2：二层下行百兆
7：企业网市场产品系列 3: 运营商市场产品系列
数字：表示更新换代。如10、20、30等 S: 分销市场专用型号产品 I:宽温系列产品系列 数字：表示设备上下行最大端口数。
款型
华为 S EI交换机 详版彩
S5720-50X-EI-46S-AC
• 46个千兆SFP，4个万兆SFP+，2个QSFP+ • 交流供电，电源前置，支持RPS冗余电源 • 交换容量：598Gbps • 包转发率：249Mpps
S5720-52X-EI-AC
• 48个10/100/1000Base-T以太网端口，4个万兆SFP+，2个 QSFP+
S5720-EI系列下一代增强型 千兆以太网交换机
S5720-EI系列下一代增强型千兆以太网交换机
产品概述
S5720-EI下一代增强型千兆以太网交换机系列（以下简称S5720-EI），是华为公司自主研发的新一 代千兆以太网交换机，提供灵活的全千兆光/电/Combo口接入以及增强的万兆上行端口扩展能力。 该系列交换机基于新一代高性能处理器和华为公司统一的VRP（Versatile Routing Platform）软件平 台，提供更大的表项规格，更高的硬件处理能力，可集成无线控制器功能，可扩展支持MACSec功 能， 具备更加完善的业务处理能力，增强的安全控制，灵活的以太组网，成熟的IPv6特性，智能 iStack堆叠，方便的运行维护等特点。广泛应用于企业园区接入、汇聚，数据中心千兆接入等多种 应用场景。
• 支持远程点灯功能，管理人员可以使用配置命令控制前面板sys灯在一段时间内快闪，从而可以在 机房中快速定位设备。
• 支持SVF超级虚拟交换网，SVF方案创新实现将原来“核心/汇聚+接入交换机+AP”的网络架构， 虚拟化为一台设备进行管理，提供业界最简化的网络管理方案，简化设备管理，实现接入交换机 和无线AP的即插即用；业务配置模板化，在核心设备上配置后自动下发到接入设备，实现集中管 控，简化业务配置，灵活调整。S5720-EI在SVF方案中支持作为client角色。
华为S5720-SI交换机-产品彩页
S5720-SI系列下一代标准型千兆以太交换机S5720-SI 系列下一代标准型千兆以太交换机1华为企业Sx700系列交换机• 包转发率：96Mpps2华为企业Sx700系列交换机强大的业务处理能力，多样的安全控制• 完善的二、三层组播协议，支持PIM SM 、PIM DM 、PIM SSM 、MLD 、IGMP Snooping ，满足多终端高清视频监控和视频会议接入需求。
• 增强支持OSPF 、ISIS 、BGP 、VRRP 等三层特性，满足企业接入、汇聚业务承载要求，支持更加丰富的语音、视频和数据应用。
• 支持MAC 认证、802.1x 认证、Portal 认证，实现用户策略（VLAN 、QoS 、ACL ）的动态下发。
• 支持完善的DoS 类防攻击、用户类防攻击。
其中，DoS 类防攻击主要针对交换机本身的攻击，包括SYN Flood 、Land 、Smurf 、ICMP Flood ；用户类防攻击涉及DHCP 服务器仿冒攻击、IP/MAC 欺骗、DHCP request flood 、改变 DHCP CHADDR 值等等。
• 通过建立和维护DHCP Snooping 绑定表，对不符合绑定表项的非法报文直接丢弃。
利用DHCPSnooping 的信任端口特性，还可以保证DHCP 服务器的合法性。
• 支持ARP 表项严格学习功能，可以防止因ARP 欺骗攻击导致正常用户无法上网。
• 支持MACSec ，提供逐跳设备的数据安全传输，适用于政府、金融等对数据机密性要求较高的场景。
轻松的运行维护• 支持SVF 超级虚拟交换网，SVF 方案创新实现将原来“核心/汇聚+接入交换机+AP ”的网络架构，虚拟化为一台设备进行管理，提供业界最简化的网络管理方案，简化设备管理，实现接入交换机和无线AP 的即插即用；业务配置模板化，在核心设备上配置后自动下发到接入设备，实现集中管控，简化业务配置，灵活调整。
S5720-SI 在SVF 方案中支持作为client 角色。
华为S5700-EI交换机详版彩页
成熟的IPv6 特性
• S5700-EI基于成熟稳定的VRP平台，支持IPv4/IPv6 双协议栈、IPv6路由协议（RIPng/OSPFv3/BGP4+/ IS-ISv6）、IPv6 over IPv4隧道（手工隧道/6to4隧道/ISATAP隧道）。S5700-EI既可以部署在纯IPv4或 IPv6网络，也可以部署在IPv4与IPv6共存的网络，充分满足网络从IPv4向IPv6过渡的需求。
Huawei S5710-EI 系列交换机彩页(临时稿)
S5710-EI系列全千兆企业网交换机产品概述Huawei S5710-EI系列全千兆企业网交换机（以下简称S5710-EI），是华为公司为满足大带宽接入和以太网多业务汇聚而推出的新一代绿色节能的全千兆高性能以太网交换机。
它基于新一代高性能硬件和华为公司统一的VRP®（Versatile Routing Platform）平台，具备大容量、高密度千兆端口，可提供万兆上行，充分满足客户对高密度千兆和万兆上行设备的需求，同时针对企业网用户的园区网接入、汇聚、IDC 千兆接入以及千兆到桌面等多种应用场景，融合了可靠、安全、绿色环保等先进技术，采用简单便利的安装维护手段，帮助客户减轻网络规划、建设和维护的压力，助力企业搭建面向未来的IT网络。
产品型号和外观S5710-EI交换机：产品特点●强大的多业务支持能力S5710-EI支持IGMP v1/v2/v3 Snooping/Filter/Fast Leave/Proxy等协议。
S5710-EI支持MCE 功能，实现了不同VPN用户在同一台设备的隔离，有效解决用户数据安全问题●完备的高可靠保护机制S5710-EI支持传统的STP/RSTP/MSTP生成树协议，并支持SmartLink和RRPP等增强型以太网技术，可以实现毫秒级链路保护倒换，保证高可靠性的网络质量。
S5710-EI支持Enhanced Trunk（E-Trunk）功能。
极大的提升了接入侧设备的可靠性。
S5710-EI支持智能以太保护SEP（Smart Ethernet Protection），SEP是一种专用于以太网链路层的环网协议。
S5710-EI支持双电源冗余供电，也可以交、直流同时输入。
用户可灵活选择单电源工作模式或者双电源工作模式，提高了设备可靠性。
S5710-EI支持VRRP虚拟路由冗余协议，与其他三层交换机构建VRRP备份组。
构建故障时的冗余路由拓朴结构，保持通讯的连续性和可靠性，有效保障网络稳定。
华为S5720I-SI系列交换机产品简介说明书
Huawei S5720I-SI SwitchesProduct BrochureHuawei S5720I-SI Series SwitchesModels and AppearancesThe following models are available in the S5720I-SI series.•Operating temperature: -40°C to +75°C1Huawei S5720I-SI Series SwitchesProduct Features and HighlightsSuitable for outdoor extreme environment•S5720I-SI supports broad operating temperature range. So the switch can be working in the outdoorcabinet in the very cold and very hot environments. The typical scenario is the access of the camera for outdoor video surveillance and ETTx.•Service ports support ±6kV lightning protection, suitable for outdoor extreme environment POE++ large power supply•S5720I-SI has PoE++ model, which supports multiple GE POE++ Ethernet electrical ports. The POE++model provides up to 60 W power supply per port.•S5720I-SI PoE++ model supports long-distance PoE++，works with Huawei M2220-I/M2221-FL/M2221-VL/M2260-I/M2220-I (8-32mm) series cameras to provide 200 m long-distance power supply through 100Mbps links, 250m through 10Mbps linksMaintenance-free through lifecycle•S5720I-28X-SI-AC and S5720I-28X-PWH-SI-AC provide built-in dual power supplies and redundancybackup of fans, maintenance-free through lifecyclePowerful service processing capability and multiple security control mechanisms•The S5720I-SI supports many Layer 2/Layer 3 multicast protocols such as PIM SM, PIM DM, PIM SSM,MLD, and IGMP snooping, to support multi-terminal high-definition video surveillance and videoconferencing services.•The S5720I-SI supports multiple Layer 3 features including OSPF, IS-IS, BGP , and VRRP , meetingenterprises' requirements on access and aggregation service bearing, and enabling a variety of voice,video, and data applications.•The S5720I-SI supports MAC address authentication, 802.1x authentication, and Portal authentication,and implements dynamic delivery of policies (VLAN, QoS, and ACL) to users.•Switching capacity: 336 Gbit/s•Operating temperature: -40°C to +65°C 2•The S5720I-SI provides a series of mechanisms to defend against DoS and user-targeted attacks. DoS attacks are targeted at switches and include SYN flood, Land, Smurf, and ICMP flood attacks. User-targeted attacks include bogus DHCP server attacks, IP/MAC address spoofing, DHCP request flood, and change of the DHCP CHADDR value.•The S5720I-SI sets up and maintains a DHCP snooping binding table, and discards the packets that do not match the table entries. You can specify DHCP snooping trusted and untrusted ports to ensure that users connect only to the authorized DHCP server.•The S5720I-SI supports strict ARP learning, which protects a network against ARP spoofing attacks to ensure normal network access.Cloud management•The Huawei cloud management platform allows users to configure, monitor, and inspect switches on the cloud, reducing on-site deployment and O&M manpower costs and decreasing network OPEX. Huawei switches support both cloud management and on-premise management modes. These twomanagement modes can be flexibly switched as required to achieve smooth evolution while maximizing return on investment (ROI).Easy O&M•The S5720I-SI supports Super Virtual Fabric (SVF), which virtualizes the "Core/aggregation + Access switch + AP" structure into a logical device. The S5720I-SI provides the simplest network management solution in the industry to simplify device management. It allows plug-and-play access switches and APs.In addition, the S5720I-SI supports service configuration templates. The templates are configured oncore devices and automatically delivered to access devices, enabling centralized control, simplified service configuration, and flexible configuration modification. The S5720I-SI functions as a client in an SVFsystem.•The S5720I-SI supports zero-touch deployment, replacement of faulty devices without additional configuration, USB-based deployment, batch configuration, and batch remote upgrade. The capabilities facilitate device deployment, upgrade, service provisioning, and other management and maintenance operations, and also greatly reduce O&M costs. The S5720I-SI can be managed using SNMP v1/v2c/v3, CLI, web-based network management system, or SSH v2.0. Additionally, it supports RMON, multiple log hosts, port traffic statistics collection, and network quality analysis, which facilitate network optimization and reconstruction.•The S5720I-SI supports the Sampled Flow (sFlow) function. It uses a method defined in the sFlow standard to sample traffic passing through it and sends sampled traffic to the collector in real time.The collected traffic statistics are used to generate statistical reports, helping enterprises maintain their networks.Multiple reliability mechanisms•The S5720I-SI supports iStack. This technology can virtualize up to nine physical switches into one logical switch. Downlink electrical ports support iStack. Member switches in a stack implement redundancybackup to improve device reliability and use inter-device link aggregation to improve link reliability. iStack provides high network scalability. You can increase a stack's ports, bandwidth, and processing capacity by simply adding member switches. iStack also simplifies device configuration and management. Aftera stack is set up, multiple physical switches are virtualized into one logical device. You can log in to anymember switch in the stack to manage all the member switches in the stack.•In addition to traditional STP, RSTP, and MSTP, the S5720I-SI supports Huawei-developed Smart Ethernet Protection (SEP) technology and the latest Ethernet Ring Protection Switching (ERPS) standard. SEP is a ring protection protocol specific to the Ethernet link layer, and applies to various ring network topologies, such as open ring topology, closed ring topology, and cascading ring topology. This protocol is reliable, easy to maintain, and implements fast protection switching within 50 ms. ERPS is defined in ITU-T G.8032.It implements millisecond-level protection switching based on traditional Ethernet MAC and bridgingfunctions.Huawei S5720I-SI Series Switches3Huawei S5720I-SI Series Switches•The S5720I-SI supports Smart Link. One S5720I-SI switch can connect to multiple aggregation switchesthrough multiple links, implementing backup of uplinks and significantly improving reliability of access devices.•The S5720I-SI supports Ethernet OAM (IEEE 802.3ah/802.1ag) to detect link faults quickly.Mature IPv6 technologies•The S5720I-SI uses the mature, stable VRP platform and supports IPv4/IPv6 dual stack, IPv6 RIPng, andIPv6 over IPv4 tunnels (including manual, 6-to-4, and ISATAP tunnels). With these IPv6 features, the S5720I-SI can be deployed on a pure IPv4 network, a pure IPv6 network, or a shared IPv4/IPv6 network,helping achieve IPv4-to-IPv6 transition.Product Specifications4Huawei S5720I-SI Series Switches Service Features5Huawei S5720I-SI Series Switches 6ApplicationsVideo surveillance application in safe city scenarioS5720I-SI supports extended operating temperature range, with professional lightning protection capabilities, suitable for outdoor cabinet environment. S5720I-SI can be used for safe city scenario to provide remote PoE access for the camera.ETTx scenarioThe S5720I-SI supports extended operating temperature and provides full gigabit access and multi-gigabit uplinks for ETTx access scenarios.Huawei S5720I-SI Series Switches7Huawei S5720I-SI Series SwitchesOrdering InformationFor more information, visit /enor contact your local Huawei sales office.8Huawei S5720I-SI Series Switches9Copyright © Huawei Technologies Co., Ltd. 2018. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.Trademark Notice, HUAWEI, and are trademarks or registered trademarks of Huawei Technologies Co., Ltd.Other trademarks, product, service and company names mentioned are the property of their respective owners.General DisclaimerThe information in this document may contain predictive statements including,without limitation, statements regarding the future financial and operating results,future product portfolio, new technology, etc. There are a number of factors thatcould cause actual results and developments to differ materially from thoseexpressed or implied in the predictive statements. Therefore, such information isprovided for reference purpose only and constitutes neither an offer nor anacceptance. Huawei may change the information at any time without notice.。
华为S5720I-SI系列视频回溯交换机产品介绍说明书
DataSheetProduct OverviewHuawei S5720I-SI series video backhaul switch is ideal for implementing outdoor video backhaul in public safety scenarios. The S5720I-SI series video backhaul switch integrates multiple modules, including an extended-temperature switch, surge protector, multiple power outputs, fiber splice tray, protection shell, and mechanical lock, meeting all the needs of an outdoor access site. Leveraging its high-performance hardware and Huawei Versatile Routing Platform (VRP), the switch provides flexible full gigabit access ports and 10GE uplink ports, supports simple operations and maintenance (O&M) and flexible Ethernet networking, and provides enhanced Layer 3 features as well as mature IPv6 functions. The S5720I-SI series video backhaul switch supports an industrial-grade operating temperature range and has a high level of outdoor surge protection. It is also IP65-rated and comes with salt spray protection. It can withstand harsh weather conditions in outdoor environments, and can be used for video access in Safe City scenarios.This series is available in two models: S5720I-6X-PWH-SI-AC and S5720I-10X-PWH-SI-AC.Models and AppearancesModels and AppearancesDescriptionS5720I-6X-PWH-SI-AC●Integrates multiple modules including the protection shell, surge protector, fiber splice tray, and multiple power outputs● 4 x 10/100/1000Base-T Ethernet ports and 2 x 10 GE SFP+ ports ● PoE++● Built-in AC power supply ● IP66● Surge protection ● Salt spray protection●Forwarding performance: 35.7 Mpps ● Switching capacity: 168 Gbit/s●Operating temperature: -40°C to +55°CS5720I-10X-PWH-SI-AC ●Integrates multiple modules including the protection shell, surge protector, fibersplice tray, and multiple power outputs●8 x 10/100/1000Base-T Ethernet ports and 2 x 10 GE SFP+ ports●PoE++●Built-in AC power supply●IP66●Surge protection●Salt spray protection●Forwarding performance: 42 Mpps●Switching capacity: 168 Gbit/s●Operating temperature: -40°C to +55°CFeatures and HighlightsIndustrial-Grade Reliability, withstanding harsh outdoor environmentsExtended operating temperature range (-40°C to +55°C), enabling it to work in harsh outdoor environments.Built-in surge protector, meeting outdoor surge protection requirements.IP66-rated, easily adapting to complex outdoor environments.Salt spray protection, supporting installation in areas more than 500 meters from the sea.High-level integration and easy installation/deploymentThe S5720I-SI series video backhaul switch integrates multiple modules, including a built-in surge protector, fiber splice tray, PoE++ power supply, multiple power outputs (12 V DC/24 V DC(or 24V AC, depending on the model)/220 V AC), protection shell, and mechanical lock, eradicating the need for on-site installation. Additionally, the switch weighs only about 10 kg, facilitating wall- and pole-mounting.Supports Super Virtual Fabric (SVF) that virtualizes "Core/Aggregation + Access Switches" into a single logical device. TheS5720I-SI can function as the SVF client. SVF provides the simplest network management solution in the industry, simplifies device management, and supports plug-and-play of devices, as well as supporting service configuration profiles. These profiles are configured on the core device and automatically delivered to access devices, implementing centralized control, simplifying service configuration, and enabling flexible configuration modification.Supports zero-touch provisioning (ZTP), USB-based deployment, configuration-free replacement of a faulty device, batch configuration, and batch remote upgrade. These functions facilitate device deployment, service provisioning, and other management and maintenance work, greatly reducing O&M costs. The switch can be managed and maintained using Simple Network Management Protocol (SNMP) v1, v2c, and v3, command line interface (CLI), web system, or Secure Shell (SSH) v2.0. Additionally, it supports remote network monitoring (RMON), multiple log hosts, interface traffic statistics collection, and network quality analysis that facilitates network optimization and reconstruction.Professional video surveillance featuresSmart Fault Diagnosis (SFD) of the downstream IP cameras (IPCs): Specifically, the switch works with Huawei's network management system—eSight—to implement fast fault diagnosis based on the device management status, port status, and alarms of the network path on which the IPC resides, and quickly demarcate the type of fault that led to the IPC disconnection (for example, an IPC fault, network device fault, power failure, or optical fiber link fault). This capability improves O&M efficiency, reduces O&M costs, and increases the IPC connectivity rate.eMDI video quality demarcation: The switch works with Huawei eSight to analyze video service quality and quickly demarcate the video quality problem type, such as artifacts and frame freezing on the screen when playing a video.Mechanical lock and alarm reporting upon cover being opened: It can quickly detect damage and intrusion, ensuring device security.Leading PoE++ power supplyPoE ++ (802.3bt): A single PoE ++ port provides up to 60 W power.Long-distance PoE++ power supply: When PoE++ ports on the switch work in FE mode and Category 5e and above network cables are used, the switch can provide 200-meter PoE power supply to the following Huawei cameras: M2220-I, M2221-FL,M2221-VL, M2260-I, and M2220-I.Fast PoE: The switch can supply power to PDs within 10s after it is powered on. This is different from common switches that generally take 1 to 3 minutes to start to supply power to PDs. The fast PoE capability greatly shortens the service interruption time caused by power supply interruption, and enables the switch and PDs to start almost at the same time. That is, after the switch is fully started, PDs can immediately function properly.Perpetual PoE technology: The switch supplies uninterrupted power to PDs even when it reboot, eliminating fault-triggered interruptions.Powerful Service Processing Capability and Multiple Security Control Mechanisms Various Layer 2 and Layer 3 multicast protocols, including Protocol Independent Multicast Sparse Mode (PIM SM), PIM Dense Mode (DM), PIM Source-Specific Multicast (SSM), Multicast Listener Discovery (MLD), and Internet Group Management Protocol (IGMP) snooping, ensuring high-quality HD video surveillance services.Layer 3 features, such as Open Shortest Path First (OSPF), Intermediate System to Intermediate System (IS-IS), Border Gateway Protocol (BGP), and Virtual Router Redundancy Protocol (VRRP), meeting enterprise access and aggregation service requirements and supporting more voice, video, and data applications.MAC address authentication, 802.1X authentication, Portal authentication, and dynamic delivery of user policies (VLAN, QoS, and ACL).Series of mechanisms to defend against DoS attacks and user-targeted attacks. DoS attacks are targeted at switches and include SYN flood, LAND, Smurf, and ICMP flood attacks. User-targeted attacks include bogus DHCP server attacks, IP/MAC address spoofing, DHCP request flood, and changing the DHCP CHADDR value.Setting up and maintaining a DHCP snooping binding table, and discarding the packets that do not match the table entries. DHCP snooping allows a physical port to be configured as a trusted or untrusted port to ensure that users are connected to only authorized DHCP servers.Strict ARP learning, protecting the network against ARP spoofing attacks and ensuring normal network access.Multiple Reliability MechanismsHuawei-developed Smart Ethernet Protection (SEP) technology and the latest Ethernet ring protection switching (ERPS) standard in addition to the traditional Spanning Tree Protocol (STP), Rapid Spanning Tree Protocol (RSTP), and Multiple Spanning Tree Protocol (MSTP). SEP is a ring protection protocol dedicated to the Ethernet link layer. It is applicable to various ring topologies such as open ring topology, closed ring topology, and cascading ring topology. SEP is reliable and easy to maintain, and implements fast protection switching (under 50 ms). ERPS is defined in ITU-T G.8032. It implements protection switching within milliseconds based on the traditional Ethernet MAC and bridging functions.Smart Link. One switch can be connected to multiple aggregation switches through multiple links to implement uplink backup, greatly improving the reliability of access devices.Ethernet OAM (IEEE 802.3ah/802.1ag), quickly detecting link faults.Mature IPv6 TechnologiesThe S5720I-SI series video backhaul switch uses the mature, stable VRP platform and supports IPv4/IPv6 dual stacks, IPv6 RIPng, and IPv6 over IPv4 tunnels including manual, 6-to-4, and Intra-Site Automatic Tunnel Addressing Protocol (ISATAP) tunnels. With these IPv6 features, the switch can be deployed on IPv4 networks, IPv6 networks, or networks that run both IPv4 and IPv6, meeting the requirements for IPv4-to-IPv6 transition.Product SpecificationsFixed port 4 x 10/100/1000Base-T ports and 2 x 10GSFP+ ports 8 x 10/100/1000Base-T ports and 2 x 10G SFP+ portsManagement port Console port (RJ45) and USB 2.0 portPoE 4 PoE++ ports, each providing up to 60 WpowerMaximum total PoE output power: 200 W(shared with 12 V DC and 24 V AC outputs)802.3af/802.3at/802.3bt standards compliance 8 PoE++ ports, each providing up to 60 W powerMaximum total PoE output power: 200 W (shared with 12 V DC and 24 V DC outputs) 802.3af/802.3at/802.3bt standards complianceDimensions (W x D x H,mm)300x110x390 300 x 100 x 390 Weight 10.1 kg 9.8 kgInput voltage Rated AC voltage: 220-240 V AC, 50/60 HzMaximum AC voltage: 176-264 V AC, 45-66 Hz Rated AC voltage: 100-240 V AC, 50/60 Hz Maximum AC voltage: 90-264 V AC, 47-63 HzPower output Maximum total output power of 12V DC/24VAC/PoE: 150 W12V DC (two outputs): 48 W in total, with amaximum of 48 W for each output24V AC (one output): 72 W220V AC (one output): maximum current of 4 A Maximum total output power of 12V DC/24V DC/PoE: 200 W12V DC (two outputs): 96 W in total, with a maximum of 96 W for each output24V DC (one output): 72 WAC:220V AC (one output): maximum current of 4 AMechanical lock SupportedCable cover Supported (optional)Fiber splice tray Built-inProtection rating IP66Surge protection AC input:Common mode: 20 kA; differential mode: 20 kA12V DC output:Common mode: 4 kV; differential mode: 2 kV 24V AC output:Common mode: 6 kV; differential mode: 2 kV 12 V/24 V DC output:Common mode: 6 kV; differential mode: 6 kVNetwork port:Differential mode: 6 kV; common mode: 1.5 kVSalt spray protection Supported, allowing the switch to be installed in areas more than 500 meters away from the sea Heat dissipation Natural heat dissipationInstallation mode Pole-mounted or wall-mountedService FeaturesMAC IEEE 802.1d compliance16K MAC address entriesAutomatic learning and aging of MAC address entriesStatic, dynamic, and blackhole MAC address entriesPacket filtering based on source MAC addressesVLAN 4K VLANsGuest VLAN and voice VLANGVRPMUX VLANVLAN assignment based on MAC addresses, protocols, IP subnets, policies, and portsVLAN mappingReliability RRPP ring topology and RRPP multi-instanceSmart Link tree topology and Smart Link multi-instance, providing protection switching withinmillisecondsSEPSTP (IEEE 802.1d), RSTP (IEEE 802.1w), and MSTP (IEEE 802.1s)ERPS (G.8032)BPDU protection, root protection, and loop protectionIP routing Static routing, RIPv1/v2, RIPng, OSPF, OSPFv3, IS-IS, IS-ISv6, BGP, BGP4+, VRRP, VRRP6, and ECMPIPv6 features Neighbor Discovery (ND)Path MTU (PMTU)IPv6 ping, IPv6 tracert, and IPv6 Telnet6to4 tunnels, ISATAP tunnels, and manually configured tunnelsMulticast IGMP v1/v2/v3, PIM-SM, PIM-DM, and PIM-SSMIGMP v1/v2/v3 snooping and IGMP fast leaveMLD v1/v2 and MLD v1/v2 snoopingIntra-VLAN multicast forwarding and inter-VLAN multicast replicationMulticast load balancing among member ports of a trunk linkControllable multicastPort-based multicast traffic statistics collectionQoS/ACL Inbound and outbound traffic rate limiting on a portPacket redirectionPort-based traffic policing and two-rate, three-color CAREight queues per portDRR, SP, and DRR+SP queue scheduling algorithmsRe-marking of the 802.1p priority and DSCP value of packetsPacket filtering on Layer 2 to Layer 4, filtering out invalid frames based on the source MAC address,destination MAC address, source IP address, destination IP address, TCP/UDP source/destinationport number, protocol number, and VLAN IDQueue-based rate limiting and traffic shaping on portsSecurity features Hierarchical user management and password protectionDoS attack defense, ARP attack defense, and ICMP attack defenseBinding of the IP address, MAC address, port number, and VLAN IDPort isolation, port security, and sticky MACMAC Forced Forwarding (MFF)Blackhole MAC address entriesLimit on the number of learned MAC addressesIEEE 802.1X authentication and limit on the number of users on a portAAA authentication, RADIUS authentication, and HWTACACS authenticationNACSSH v2.0HTTPSCPU protectionBlacklist and whitelistDHCPv4/v6 client/relay/server/snoopingAttack source tracing and punishment for IPv6 packets such as ND, DHCPv6, and MLD packetsSeparation between user authentication and policy enforcement pointsReliability LACPE-trunkEthernet OAM (IEEE 802.3ah and 802.1ag)ITU-Y.1731DLDPLLDPBFD for BGP/IS-IS/OSPF/static routeSuper Virtual Fabric (SVF) Plug-and-playAutomatic loading of software and patches One-click automatic provisioning of servicesConfiguration of an AS in independent mode and configuration of services that are not supported bythe profile on the parentOAM EFMCFMY.1731Management and maintenance Virtual cable testSNMPv1/v2c/v3RMONNetwork management system (NMS) and web-based network management features System logs and multi-level alarmssFlowNETCONFDying gaspAlarms upon opening the cover of the deviceOffline IPC fault diagnosiseMDIInterconnection and interoperability VLAN-based Spanning Tree (VBST) (compatible with PVST/PVST+/RPVST) Link-type Negotiation Protocol (LNP) (similar to DTP)VLAN Central Management Protocol (VCMP) (similar to VTP)Networking and ApplicationsVideo surveillance network in Safe City scenariosThe S5720I-SI series video backhaul switch supports an extended operating temperature range, has a built-in surge protector, and provides IP65 protection as well as salt spray protection capabilities. It is applicable to outdoor environments and can be used in Safe City scenarios to provide long-distance PoE access for cameras.Ordering InformationS5720I-6X-PWH-SI-ACS5720I-6X-PWH-SI-AC (4*10/100/1000BASE-T ports, 2*10GE SFP+ ports, PoE++, AC power supply)S5720I-10X-PWH-SI-ACS5720I-10X-PWH-SI-AC (8*10/100/1000BASE-T ports, 2*10GE SFP+ ports, PoE++, AC power supply)ES5MPJB00000Cable cover (used in S5720I-10X-PWH-SI-AC and S5720I-6X-PWH-SI-AC)More InformationFor more information about Huawei Campus Switches, visit or contact us in the following ways: ● Global service hotline: /en/service-hotline● Logging in to the Huawei Enterprise technical support website: /enterprise/ ● Sending an email to the customer service mailbox: ********************Copyright © Huawei Technologies Co., Ltd. 2018. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissionsand other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders. NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.Huawei Technologies Co., Ltd. Address:Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China Website:。
最新华为s572048交换机配置资料
华为s5720-48交换机配置<S572048>dis cu!Software Version V200R010C00SPC600#sysname S572048#vlan batch 10 100#authentication-profile name default_authen_profileauthentication-profile name dot1x_authen_profileauthentication-profile name mac_authen_profileauthentication-profile name portal_authen_profileauthentication-profile name dot1xmac_authen_profileauthentication-profile name multi_authen_profile#dhcp enable#radius-server template default#free-rule-template name default_free_rule#portal-access-profile name portal_access_profile#aaaauthentication-scheme defaultauthentication-scheme radiusauthentication-mode radiusauthorization-scheme defaultaccounting-scheme defaultlocal-aaa-user password policy administratorpassword expire 0domain defaultauthentication-scheme radiusradius-server defaultdomain default_adminauthentication-scheme defaultlocal-user admin password irreversible-cipher $1a$M%I/M!PQFR$]|[KXug2w.)5"e-~fH_,[$}|3`XTO.hbs6,)tj`$$local-user admin privilege level 15local-user admin service-type terminal http#interface Vlanif1#interface Vlanif10ip address 192.168.10.254 255.255.255.0 dhcp select relaydhcp relay server-ip 192.168.0.1#interface Vlanif100ip address 192.168.0.254 255.255.255.0 dhcp select interfacedhcp select relaydhcp relay server-ip 192.168.0.1#interface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan 10 100#interface GigabitEthernet0/0/2port link-type trunkport trunk allow-pass vlan 10 100#interface GigabitEthernet0/0/3port link-type accessport default vlan 10#interface GigabitEthernet0/0/4port link-type accessport default vlan 10#interface GigabitEthernet0/0/5port link-type accessport default vlan 10#interface GigabitEthernet0/0/6port link-type accessport default vlan 10#interface GigabitEthernet0/0/7port link-type accessport default vlan 10#interface GigabitEthernet0/0/8port link-type accessport default vlan 10#interface GigabitEthernet0/0/9port default vlan 10#interface GigabitEthernet0/0/10 port link-type accessport default vlan 10#interface GigabitEthernet0/0/11 port link-type accessport default vlan 10#interface GigabitEthernet0/0/12 port link-type accessport default vlan 10#interface GigabitEthernet0/0/13 port link-type accessport default vlan 10#interface GigabitEthernet0/0/14 port link-type accessport default vlan 10#interface GigabitEthernet0/0/15 port link-type accessport default vlan 10#interface GigabitEthernet0/0/16 port link-type accessport default vlan 10#interface GigabitEthernet0/0/17 port link-type accessport default vlan 10#interface GigabitEthernet0/0/18 port link-type accessport default vlan 10#interface GigabitEthernet0/0/19 port link-type accessport default vlan 10#interface GigabitEthernet0/0/20port default vlan 10#interface GigabitEthernet0/0/21 port link-type accessport default vlan 10#interface GigabitEthernet0/0/22 port link-type accessport default vlan 10#interface GigabitEthernet0/0/23 port link-type accessport default vlan 10#interface GigabitEthernet0/0/24 port link-type accessport default vlan 10#interface GigabitEthernet0/0/25 port link-type accessport default vlan 10#interface GigabitEthernet0/0/26 port link-type accessport default vlan 10#interface GigabitEthernet0/0/27 port link-type accessport default vlan 10#interface GigabitEthernet0/0/28 port link-type accessport default vlan 10#interface GigabitEthernet0/0/29 port link-type accessport default vlan 10#interface GigabitEthernet0/0/30 port link-type accessport default vlan 10#interface GigabitEthernet0/0/31port default vlan 10#interface GigabitEthernet0/0/32 port link-type accessport default vlan 10#interface GigabitEthernet0/0/33 port link-type accessport default vlan 10#interface GigabitEthernet0/0/34 port link-type accessport default vlan 10#interface GigabitEthernet0/0/35 port link-type accessport default vlan 10#interface GigabitEthernet0/0/36 port link-type accessport default vlan 10#interface GigabitEthernet0/0/37 port link-type accessport default vlan 10#interface GigabitEthernet0/0/38 port link-type accessport default vlan 10#interface GigabitEthernet0/0/39 port link-type accessport default vlan 10#interface GigabitEthernet0/0/40 port link-type accessport default vlan 10#interface GigabitEthernet0/0/41 port link-type accessport default vlan 10#interface GigabitEthernet0/0/42port default vlan 10#interface GigabitEthernet0/0/43port link-type accessport default vlan 10#interface GigabitEthernet0/0/44port link-type accessport default vlan 10#interface GigabitEthernet0/0/45port link-type accessport default vlan 10#interface GigabitEthernet0/0/46port link-type accessport default vlan 10#interface GigabitEthernet0/0/47port link-type accessport default vlan 10#interface GigabitEthernet0/0/48port link-type accessport default vlan 100#interface GigabitEthernet0/0/49#interface GigabitEthernet0/0/50#interface GigabitEthernet0/0/51#interface GigabitEthernet0/0/52#interface NULL0#ip route-static 0.0.0.0 0.0.0.0 192.168.0.1 #user-interface con 0authentication-mode aaauser-interface vty 0 4user-interface vty 16 20#port-group zugroup-member GigabitEthernet0/0/3 group-member GigabitEthernet0/0/4 group-member GigabitEthernet0/0/5 group-member GigabitEthernet0/0/6 group-member GigabitEthernet0/0/7 group-member GigabitEthernet0/0/8 group-member GigabitEthernet0/0/9 group-member GigabitEthernet0/0/10 group-member GigabitEthernet0/0/11 group-member GigabitEthernet0/0/12 group-member GigabitEthernet0/0/13 group-member GigabitEthernet0/0/14 group-member GigabitEthernet0/0/15 group-member GigabitEthernet0/0/16 group-member GigabitEthernet0/0/17 group-member GigabitEthernet0/0/18 group-member GigabitEthernet0/0/19 group-member GigabitEthernet0/0/20 group-member GigabitEthernet0/0/21 group-member GigabitEthernet0/0/22 group-member GigabitEthernet0/0/23 group-member GigabitEthernet0/0/24 group-member GigabitEthernet0/0/25 group-member GigabitEthernet0/0/26 group-member GigabitEthernet0/0/27 group-member GigabitEthernet0/0/28 group-member GigabitEthernet0/0/29 group-member GigabitEthernet0/0/30 group-member GigabitEthernet0/0/31 group-member GigabitEthernet0/0/32 group-member GigabitEthernet0/0/33 group-member GigabitEthernet0/0/34 group-member GigabitEthernet0/0/35 group-member GigabitEthernet0/0/36 group-member GigabitEthernet0/0/37 group-member GigabitEthernet0/0/38group-member GigabitEthernet0/0/39group-member GigabitEthernet0/0/40 group-member GigabitEthernet0/0/41 group-member GigabitEthernet0/0/42group-member GigabitEthernet0/0/43group-member GigabitEthernet0/0/44group-member GigabitEthernet0/0/45#dot1x-access-profile name dot1x_access_profile #mac-access-profile name mac_access_profile#return<S572048>。
华为S5700-EI系列交换机产品手册说明书
Huawei S5700-EI Series SwitchesProduct BrochureThe S5700-EI series gigabit enterprise switches (S5700-EI) are next-generation energy-saving switchesdeveloped by Huawei to meet the demand for high-bandwidth access and Ethernet multi-servicemaintain, reducing workloads for network planning, construction, and maintenance. The S5700-EI usesS5700-EI Series Gigabit Enterprise Switches Product OverviewProduct Appearance•Switching capacity: 416Gbps2-2Huawei Enterprise Sx700 Series Switch Product•Switching capacity: 416GbpsProduct Features and highlightsPowerful support for services•The S5700-EI supports IGMP v1/v2/v3 snooping, IGMP filter, IGMP fast leave, and IGMP proxy. It supportsline-speed replication of multicast packets between VLANs, multicast load balancing among member interfaces of a trunk, and controllable multicast, meeting requirements for IPTV services and othermulticast services.•The S5700-EI provides the Multi-VPN-Instance CE (MCE) function to isolate users in different VPNs on a device, ensuring data security and reducing costs.•The S5710-EI supports multiple MPLS & VPN features, including Label Distribution Protocol (LDP) or Resource Reservation Protocol for Traffic Engineering (RSVP-TE), MPLS TE, VLL, VPLS, and MPLS L3VPN. Comprehensive reliability mechanisms•Besides STP, RSTP, and MSTP, the S5700-EI supports enhanced Ethernet reliability technologies such asSmart Link and RRPP (Rapid Ring Protection Protocol), which implement millisecond-level protection switchover and ensure network reliability. It also provides Smart Link multi-instance and RRPP multi-instance to implement load balancing among links, optimizing bandwidth usage.Huawei Enterprise Sx700 Series Switch Product2-3•The S5700-EI supports enhanced trunk (E-Trunk) that enables a CE to be dual-homed to two PEs (S5700s).E-Trunk greatly enhances link reliability between devices and implements link aggregation betweendevices. This improves reliability of access devices.•The S5700-EI supports the Smart Ethernet Protection (SEP) protocol, a ring network protocol applied tothe link layer on an Ethernet network. SEP can be used on open ring networks and can be deployed onupper-layer aggregation devices to provide fast switchover, ensuring non-stop transmission of services.SEP features simplicity, high reliability, fast switchover, easy maintenance, and flexible topology, facilitatingnetwork planning and management.•The S5700-EI supports Ethernet Ring Protection Switching (ERPS), also referred to as G.8032. As the latestring network protocol, ERPS was developed based on traditional Ethernet MAC and bridging functionsand uses mature Ethernet OAM function and a Ring Automatic Protection Switching (R-APS) mechanismto implement millisecond-level protection switching. ERPS supports various services and allows flexiblenetworking, helping customers build a network with lower OPEX and CAPEX.•The S5700-EI supports redundant power supplies, and can use an AC power supply and a DC powersimultaneously. Users can choose a single power supply or use two power supplies to ensure devicereliability.•The S5700-EI supports VRRP, and can set up VRRP groups with other Layer 3 switches. VRRP providesredundant routes to ensure stable and reliable communication. Multiple equal-cost routes to an uplinkdevice can be configured on the S5700-EI to provide route redundancy. When an active route isunreachable, traffic is switched to a backup route.•The S5700-EI supports Bidirectional Forwarding Detection (BFD) and provides millisecond-level detectionfor protocols such as OSPF, IS-IS, VRRP, and PIM to improve network reliability. The S5700-EI complies withIEEE 802.3ah and 802.1ag. IEEE 802.3ah defines the mechanism for detecting faults on direct links overthe Ethernet in the first mile, and 802.1ag defines the mechanism for end-to-end service fault detection.The S5700-EI supports Y.1731. Besides fast end-to-end service fault detection, the S5700-EI can use theperformance measurement tools defined in Y.1731 to monitor network performance, providing accuratedata about network quality.Well-designed QoS policies and security mechanisms•The S5700-EI implements complex traffic classification based on packet information such as the 5-tuple,IP precedence, ToS, DSCP, IP protocol type, ICMP type, TCP/UDP port number, VLAN ID, Ethernet protocoltype. ACLs can be applied to inbound or outbound direction on an interface. The S5700-EI supportsa flow-based two-rate three-color CAR. Each port supports eight priority queues and multiple queuescheduling algorithms such as WRR, DRR, SP, WRR+SP, and DRR+SP. All of these ensure the quality ofvoice, video, and data services.Huawei Enterprise Sx700 Series Switch Product•The S5700-EI provides multiple security measures to defend against Denial of Service (DoS) attacks,and attacks against networks or users. DoS attack types include SYN Flood attacks, Land attacks, Smurf attacks, and ICMP Flood attacks. Attacks to networks refer to STP BPDU/root attacks. Attacks to users include bogus DHCP server attacks, man-in-the-middle attacks, IP/MAC spoofing attacks, DHCP requestflood attacks. DoS attacks that change the CHADDR field in DHCP packets are also attacks against users.•The S5700-EI supports DHCP snooping, which discards invalid packets that do not match any binding entries, such as ARP spoofing packets and IP spoofing packets. This prevents man-in-the-middle attacksto campus networks that hackers initiate by using ARP packets. The interface connected to a DHCP server can be configured as a trusted interface to protect the system against bogus DHCP server attacks.•The S5700-EI supports strict ARP learning, which prevents ARP spoofing attacks that will exhaust ARP entries. It also provides IP source check to prevent DoS attacks caused by MAC address spoofing, IP address spoofing, and MAC/IP spoofing.•The S5700-EI supports 802.1x authentication, MAC address authentication, and combined authentication on a per port basis, as well as Portal authentication on a per VLANIF interface basis. The S5700-EI also supports NAC. The S5700-EI authenticates users based on statically or dynamically bound user information such as the user name, IP address, MAC address, VLAN ID, access interface, and flag indicating whether antivirus software is installed. VLANs, QoS policies, and ACLs can be applied to users dynamically.•The S5700-EI can limit the number of MAC addresses learned on an interface to prevent attackers from exhausting MAC address entries by using bogus source MAC addresses. This function minimizes packetflooding that occurs when MAC addresses of users cannot be found in the MAC address table.Fine-grained traffic management•The S5710-EI supports NetStream. The NetStream module supports V5, V8, and V9 packet formats and provides various traffic analysis functions, such as real-time traffic sampling, dynamic report generation, traffic attribute analysis, and traffic exception report. The Netstream module enables administrators to monitor network status in real time and provides applications and analysis functions including potential fault detection, effective fault rectification, fast problem handling, and security monitoring, to help customers optimize network structure and adjust resource deployment.•The S5700-EI supports the Sampled Flow (sFlow) function, which uses a sampling mechanism to obtain statistics about traffic forwarded on a network and sends the statistics to the Collector in real time. The Collector analyzes traffic statistics to help customers manage network traffic efficiently. The S5700-EI integrates the sFlow Agent module and uses hardware for traffic monitoring. Unlike traffic monitoring through port mirroring, sFlow does not degrade network performance during traffic monitoring.Easy deployment and maintenance free•The S5700-EI supports automatic configuration, plug-and-play, and batch remote upgrade. These capabilities simplify device management and maintenance and reduce maintenance costs. The S5700-EI supports SNMP v1/v2c/v3 and provides flexible methods for managing devices. Users can manageHuawei Enterprise Sx700 Series Switch Productthe S5700-EI using the CLI and Web NMS. The NQA function helps users with network planning andupgrading. In addition, the S5700-EI supports NTP, SSH v2, HWTACACS+, RMON, log hosts, and port-based traffic statistics.•EasyDeploy: The Commander collects information about the topology of the client connecting to theCommander and saves client startup information based on the topology. The client can be replacedwithout configuration. Configuration and scripts can be delivered to the client in batches. In addition, theconfiguration delivery result can be queried. The Commander can collect and display power consumptionon the entire network.•The S5700-EI supports the GARP VLAN Registration Protocol (GVRP), which dynamically distributes,registers, and propagates VLAN attributes to reduce manual configuration workloads of networkadministrators and to ensure correct VLAN configuration. In a complex network topology, GVRP simplifiesVLAN configuration and reduces network communication faults caused by incorrect VLAN configuration.•The S5700-EI supports MUX VLAN. MUX VLAN isolates Layer 2 traffic between interfaces in a VLAN.Interfaces in a subordinate separate VLAN can communicate with ports in the principal VLAN but cannotcommunicate with each other. MUX VLAN is usually used on an enterprise intranet to isolate userinterfaces from each other but allow them to communicate with server interfaces. This function preventscommunication between network devices connected to certain interfaces or interface groups but allowsthe devices to communicate with the default gateway.PoE function•The S5700-EI PWR can use PoE power supplies with different power levels to provide -48V DC power forPowered Devices (PDs) such as IP phones, WLAN APs, and Bluetooth APs. In its role as Power SourcingEquipment (PSE), the S5700-EI PWR complies with IEEE 802.3af and 802.3at (PoE+) and can work with PDsthat are incompatible with 802.3af or 802.3at. Each port provides a maximum of 30 W power, complyingwith IEEE 802.3at. The PoE+ function increases the maximum power of each port and implements intelligentpower management for high-power consumption applications. This facilitates the use of PDs. PoE portscan work in power-saving mode. The S5700-EI PWR provides improved PoE solutions. Users can configurewhether and when a PoE port supplies power.High scalability•The S5700-EI supports intelligent stacking (iStack). Multiple S5700-EI switches can be connected withstack cables to set up a stack, which functions as a virtual switch. A stack consists of a master switch,a backup switch, and several slave switches. The backup switch takes over services when the masterswitch fails, reducing service interruption time. Stacks support intelligent upgrade so that users do notneed to change the software version of a switch when adding it to a stack. The iStack function allowsusers to connect multiple switches with stack cables to expand system capacity. These switches can bemanaged using a single IP address, which greatly reduces the costs of system expansion, operation, andmaintenance. Compared with traditional networking technologies, iStack has advantages in scalability,reliability, and system architecture.Huawei Enterprise Sx700 Series Switch ProductVarious IPv6 features•The S5700-EI supports IPv4/IPv6 dual stack and can migrate from an IPv4 network to an IPv6 network.S5700-EI hardware supports IPv4/IPv6 dual stack, IPv6 over IPv4 tunnels (including manual tunnels, 6to4tunnels, and ISATAP tunnels), and Layer 3 line-speed forwarding. The S5700-EI can be deployed on IPv4networks, IPv6 networks, or networks that run both IPv4 and IPv6. This makes networking flexible andenables easy migration from IPv4 to IPv6.Product Specifications2-7Huawei Enterprise Sx700 Series Switch ProductHuawei Enterprise Sx700 Series Switch Product*:The S5700 switches of the EI series are collectively called S5700-EI. S5710-EI is a sub-series switches of S5700-EI .2-9Huawei Enterprise Sx700 Series Switch ProductOn Large-sized Enterprise NetworksThe S5700-EI can function as an access device on a large-sized enterprise network or an aggregation device on a small-sized or medium-sized campus network. It supports link aggregation and dual-homing to improve network reliability.In Data CentersThe S5700-EI can be used in a data center. It connects to gigabit servers and aggregates traffic from the servers to uplink devices through trunk links. If multiple servers are available, an S5700-EI stack can be used to facilitate network maintenance and improve network reliability.InternetWANApplicationsHuawei Enterprise Sx700 Series Switch ProductFor more information, visit or contact your local Huawei sales office.S5710-28C-EI(24xEthernet 10/100/1000 ports,4 of which are dual-purpose 10/100/1000 or SFP ,4x10 GigSFP+, without power module)S5710-28C-PWR-EI-AC(24xEthernet 10/100/1000 PoE+ ports,4 of which are dual-purpose 10/100/1000 orSFP ,4x10 Gig SFP+, with 580W AC power)S5710-52C-EI(48xEthernet 10/100/1000 ports,4x10 Gig SFP+, with 2 interface slots, without powermodule)S5710-52C-PWR-EI(48xEthernet 10/100/1000 PoE+ ports, 4x10 Gig SFP+, with 2 interface slots, withoutpower module)8xGig SFP interface card(used in S5710-EI series)8xEthernet 10/100/1000 ports interface card(used in S5710-EI series)4xGig SFP interface card(including 4xGig SFP optical interface, extend channel card)(used in S5700-EI series)2x10GE SFP+ interface card(used in S5710-EI series)2x10GE SFP+ interface card(used in S5700-SI and S5700-EI series)4x10GE SFP+ optical interface card(including 4x10GE SFP+ interface, extend channel card)(used in S5700-SIand S5700-EI series)Ethernet Stack Interface Card(Including stack card,100cm stack cable)Ethernet Stack Interface Card(Including stack card,300cm stack cable)150W AC Power Module150W DC Power Module500W AC PoE Power Module580W AC PoE Power Module 1150W AC PoE Power Module Product List2-11Huawei Enterprise Sx700 Series Switch ProductCopyright © Huawei Technologies Co., Ltd. 2015. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.Trademark Notice, HUAWEI, and are trademarks or registered trademarks of Huawei Technologies Co., Ltd.Other trademarks, product, service and company names mentioned are the property of their respective owners.General DisclaimerThe information in this document may contain predictive statements including,without limitation, statements regarding the future financial and operating results,future product portfolio, new technology, etc. There are a number of factors thatcould cause actual results and developments to differ materially from thoseexpressed or implied in the predictive statements. Therefore, such information isprovided for reference purpose only and constitutes neither an offer nor anacceptance. Huawei may change the information at any time without notice.。
华为 S5720-EI下一代增强型千兆交换机 产品技术和竞争策略胶片-20141128
8
S5720-C(PC)-EI后面板描述
S5720-36C-EI-AC S5720-36C-PWR-EI-AC S5720-56C-EI-AC S5720-56C-PWR-EI-AC S5720-56C-PWR-EI-AC1
8. 接地螺钉 9. 序列号标签
S5720-36C-EI-28S-AC
10. 插卡槽位 11. 风扇模块槽位
简易运维
满足多应用场景
1
S5720-EI应用场景
大企业园区汇聚接入
WAN 分支机构 Router Internet
楼层视频监控网核心
远程访问 Internet
WAN
DMZ
S12700
eSight
S5720-EI
媒体服务器
S5700-LI S7700 S7700
S5700-LI S2700
S5720-EI
内置单电源，外 接RPS备份
--小园区核心，大园区汇聚接入，低商务且更高转发性能，更丰富的业务特性
S5720-32X-EI-AC S5720-32X-EI24S-AC S5720-50X-EI-AC S5720-50X-EI46S-AC
款型
S5720-52X-EIAC
442×420×43.6 双模块电源，1+1冗余备份
S5720-36PC-EI-AC
S5720-56PC-EI-AC
专用 2xQSFP+ 堆叠卡
4
S5720-EI产品子款型概述
设备系列 设备型号
S5720-36C-EI-AC S5720-56C-EI-AC S5720-36C-EI-28S-AC S5720-C-EI S5720-56C-EI-48S-AC S5720-36C-PWR-EI-AC S5720-56C-PWR-EI-AC S5720-56C-PWR-EI-AC1(PoE满供) S5720-PC-EI S5720-EI S5720-X-EI S5720-36PC-EI-AC S5720-56PC-EI-AC S5720-32X-EI-AC S5720-52X-EI-AC S5720-50X-EI-AC S5720-32X-EI-24S-AC S5720-50X-EI-46S-AC S5720-P-EI S5720-32P-EI-AC S5720-52P-EI-AC
华为 S5720-EI交换机 详版彩页
S5720-EI系列下一代增强型千兆以太网交换机S5720-EI系列下一代增强型千兆以太网交换机1华为企业Sx700系列交换机• 交换容量：598G/5.98Tbps • 包转发率：222Mpps2华为企业Sx700系列交换机产品特性和优势轻松的运行维护• 电源端口前置的款型可以满足300mm深的机柜放置，整台设备可以前面板单面维护，简化了运维，而且机柜的摆放更加灵活，可以灵活选择机柜靠墙放置或者机柜背靠背放置，满足客户机柜深度小、机房空间有限的需求，并为客户节省空间。
• 支持远程点灯功能，管理人员可以使用配置命令控制前面板sys灯在一段时间内快闪，从而可以在机房中快速定位设备。
• 支持SVF超级虚拟交换网，SVF方案创新实现将原来“核心/汇聚+接入交换机+AP”的网络架构，虚拟化为一台设备进行管理，提供业界最简化的网络管理方案，简化设备管理，实现接入交换机和无线AP的即插即用；业务配置模板化，在核心设备上配置后自动下发到接入设备，实现集中管控，简化业务配置，灵活调整。
S5720-EI在SVF方案中支持作为client角色。
• 支持华为Easy Operation简易运维方案，提供新入网设备Zero-Touch 安装、故障设备更换免配置、USB开局、设备批量配置、批量远程升级等功能，便于安装、升级、业务发放和其他管理维护工作，降低了运维成本。
支持SNMP v1/v2c/v3、CLI（命令行）、Web网管、SSHv2.0等多样化的管理和维护方式；支持RMON、多日志主机、端口流量统计和网络质量分析，便于网络优化和改造。
3华为企业Sx700系列交换机多样的可靠性保护• 支持智能iStack堆叠，将多台支持堆叠特性的交换机组合在一起，最大可将9台物理交换机从逻辑上虚拟为一台交换机。
多台成员设备之间冗余备份，提高了设备级的可靠性；通过跨设备的链路聚合功能，提高了链路级的可靠性。
iStack提供了强大的网络扩展能力，轻松地扩展堆叠系统的端口数、带宽和处理能力并简化了配置和管理。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
S5720-EI系列下一代增强型千兆以太网交换机S5720-EI系列下一代增强型千兆以太网交换机1华为企业Sx700系列交换机• 交换容量：598G/5.98Tbps • 包转发率：222Mpps2华为企业Sx700系列交换机产品特性和优势轻松的运行维护• 电源端口前置的款型可以满足300mm深的机柜放置，整台设备可以前面板单面维护，简化了运维，而且机柜的摆放更加灵活，可以灵活选择机柜靠墙放置或者机柜背靠背放置，满足客户机柜深度小、机房空间有限的需求，并为客户节省空间。
• 支持远程点灯功能，管理人员可以使用配置命令控制前面板sys灯在一段时间内快闪，从而可以在机房中快速定位设备。
• 支持SVF超级虚拟交换网，SVF方案创新实现将原来“核心/汇聚+接入交换机+AP”的网络架构，虚拟化为一台设备进行管理，提供业界最简化的网络管理方案，简化设备管理，实现接入交换机和无线AP的即插即用；业务配置模板化，在核心设备上配置后自动下发到接入设备，实现集中管控，简化业务配置，灵活调整。
S5720-EI在SVF方案中支持作为client角色。
• 支持华为Easy Operation简易运维方案，提供新入网设备Zero-Touch 安装、故障设备更换免配置、USB开局、设备批量配置、批量远程升级等功能，便于安装、升级、业务发放和其他管理维护工作，降低了运维成本。
支持SNMP v1/v2c/v3、CLI（命令行）、Web网管、SSHv2.0等多样化的管理和维护方式；支持RMON、多日志主机、端口流量统计和网络质量分析，便于网络优化和改造。
3华为企业Sx700系列交换机多样的可靠性保护• 支持智能iStack堆叠，将多台支持堆叠特性的交换机组合在一起，最大可将9台物理交换机从逻辑上虚拟为一台交换机。
多台成员设备之间冗余备份，提高了设备级的可靠性；通过跨设备的链路聚合功能，提高了链路级的可靠性。
iStack提供了强大的网络扩展能力，轻松地扩展堆叠系统的端口数、带宽和处理能力并简化了配置和管理。
• 支持可插拔双电源模块，实现1+1冗余备份，支持交流和直流电源模块混插，可以根据实际需要灵活配置交流或直流电源模块。
支持可插拔双风扇，根据温度变化智能调节风扇的转速，提高设备级可靠性。
• 不仅支持传统的STP/RSTP/MSTP生成树协议，还支持华为自主创新的SEP 智能以太保护技术和业界最新的以太环网标准ERPS。
SEP是一种专用于以太链路层的环网协议，适用于半环、整环、级连环等各种组网，其协议简单可靠、维护方便，并提供50ms的快速业务倒换。
ERPS是ITU-T发布的G.8032标准，该标准基于传统的以太网MAC和网桥功能，实现以太环网的毫秒级快速保护倒换。
• 支持SmartLink和VRRP功能。
通过多条链路接入到多台汇聚交换机上，SmartLink/VRRP实现了上行链路的备份，极大地提升了接入侧设备的可靠性。
• 支持多种连接故障快速检测功能。
支持完善的以太OAM (IEEE802.3ah/802.1ag/ITU Y.1731)和BFD功能。
增强的业务处理能力，完善的安全控制• 支持Multi-VPN-Instance CE（MCE）功能。
支持下接不同的VPN用户，通过更大规格的路由多实例，实现了不同用户的隔离；上行通过共用的物理接口连接到PE设备，减少单个VPN用户对网络部署的投资。
支持MPLS L3VPN、MPLS L2VPN(VPWS\VPLS)、MPLS-TE、MPLS QoS等功能，是业界为数不多的高性价比盒式MPLS 交换机。
• 提供高品质的QoS（Quality of Service）能力，具备完善的队列调度算法、拥塞控制算法，创新的优先级调度算法和多级队列调度机制，能够对数据流实现多级的精确调度，从而满足企业不同用户终端、不同业务种类的服务质量要求。
• 增强的NAC功能，支持802.1x认证、MAC认证、Portal认证、混合认证，实现VLAN、QoS、ACL等用户策略的动态下发，支持对用户分组管理，为用户配置免认证IP网段和用户HTTP访问URL重定向功能可实现客户端的快速部署，支持对无HTTP访问能力的终端主动触发Portal认证。
• 支持完善的DoS类防攻击、用户类防攻击。
其中，DoS类防攻击主要针对交换机本身的攻击，包括SYN Flood、Land、Smurf、ICMP Flood；用户类防攻击涉及DHCP服务器仿冒攻击、IP/MAC 欺骗、DHCP request flood、改变DHCP CHADDR 值等等。
• 通过建立和维护DHCP Snooping绑定表，对不符合绑定表项的非法报文直接丢弃。
利用DHCP Snooping的信任端口特性，还可以保证DHCP服务器的合法性。
• 支持ARP表项严格学习功能，可以防止因ARP欺骗攻击导致正常用户无法上网。
成熟的IPv6 特性• 基于成熟稳定的VRP平台，支持IPv4/IPv6 双协议栈、IPv6路由协议（RIPng/OSPFv3/BGP4+/IS-ISv6）、IPv6 over IPv4隧道（手工隧道/6to4隧道/ISATAP隧道）。
既可以部署在纯IPv4或IPv6网络，也可以部署在IPv4与IPv6共存的网络，充分满足网络从IPv4向IPv6过渡的需求。
华为企业Sx700系列交换机4产品规格5华为企业Sx700系列交换机华为企业Sx700系列交换机67华为企业Sx700系列交换机华为企业Sx700系列交换机8企业网络应用S5720-EI 可以作为大中型企业网络的接入设备，小型或中型园区网的汇聚设备，利用链路捆绑、双归等组网，充分提高网络可靠性。
数据中心网络应用S5720-EI 可用在数据中心，接入千兆服务器，再利用链路捆绑汇聚到上层设备。
单机架服务器超过一定数量可采用堆叠方式完成服务器接入，便于维护和提高可靠性。
Internet WAN组网应用合作方APAPAPAP9华为企业Sx700系列交换机更多信息，敬请访问华为网站或联系华为当地销售机构。
S5720-32P-EI-AC(24个10/100/1000Base-T 以太网端口，8个千兆SFP ，交流供电，前维护)S5720-32X-EI-AC(24个10/100/1000Base-T 以太网端口，4个千兆SFP ，4个万兆SFP+，交流供电，前维护)S5720-32X-EI-DC (24个10/100/1000Base-T 以太网端口，4个千兆SFP ，4个万兆SFP+，直流供电，前维护)S5720-32X-EI-24S-AC(24个千兆SFP ，4个10/100/1000Base-T 以太网端口，4个万兆SFP+，交流供电，前维护)S5720-32X-EI-24S-DC(24个千兆SFP ，4个10/100/1000Base-T 以太网端口，4个万兆SFP+，直流供电，前维护)S5720-36C-EI-AC(28个10/100/1000Base-T 以太网端口，4个复用的千兆Combo SFP ，4个万兆SFP+，单子卡槽位，含1个150W交流电源)S5720-36C-EI-DC(28个10/100/1000Base-T 以太网端口，4个复用的千兆Combo SFP ，4个万兆SFP+，单子卡槽位，含1个150W 直流电源)S5720-36C-PWR-EI-AC(28个10/100/1000Base-T 以太网端口，4个复用的千兆Combo SFP ，4个万兆SFP+，单子卡槽位，PoE+，含1个500W 交流电源)S5720-36C-PWR-EI-DC(28个10/100/1000Base-T 以太网端口，4个复用的千兆Combo SFP ，4个万兆SFP+，单子卡槽位，PoE+，含1个650W 直流电源)S5720-36PC-EI-AC(28个10/100/1000Base-T 以太网端口，4个复用的千兆Combo SFP ，4个千兆SFP ，单子卡槽位，含1个150W交流电源)S5720-36C-EI-28S-AC(28个千兆SFP ，4个复用的千兆10/100/1000Base-T 以太网端口Combo ，4个万兆SFP+，单子卡槽位，含1个150W 交流电源)S5720-36C-EI-28S-DC(28个千兆SFP ，4个复用的千兆10/100/1000Base-T 以太网端口Combo ，4个万兆SFP+，单子卡槽位，含1个150W 直流电源)S5720-50X-EI-AC(46个10/100/1000Base-T 以太网端口，4个万兆SFP+，交流供电，前维护)S5720-50X-EI-DC(46个10/100/1000Base-T 以太网端口，4个万兆SFP+，直流供电，前维护)S5720-50X-EI-46S-AC(46个千兆SFP ，4个万兆SFP+，交流供电，前维护)S5720-50X-EI-46S-DC(46个千兆SFP ，4个万兆SFP+，直流供电，前维护)S5720-52X-EI-AC(48个10/100/1000Base-T 以太网端口，4个万兆SFP+，交流供电)S5720-52P-EI-AC(48个10/100/1000Base-T 以太网端口，4个千兆SFP ，交流供电)S5720-56C-EI-48S-AC(48个千兆SFP ，4个万兆SFP+，单子卡槽位，含1个150W 交流电源)S5720-56C-EI-48S-DC(48个千兆SFP ，4个万兆SFP+，单子卡槽位，含1个150W 直流电源)S5720-56C-EI-AC(48个10/100/1000Base-T 以太网端口，4个万兆SFP+，单子卡槽位，含1个150W 交流电源)S5720-56C-EI-DC(48个10/100/1000Base-T 以太网端口，4个万兆SFP+，单子卡槽位，含1个150W 直流电源)S5720-56PC-EI-AC(48个10/100/1000Base-T 以太网端口，4个千兆SFP ，单子卡槽位，含1个150W 交流电源)S5720-56C-PWR-EI-AC(48个10/100/1000Base-T 以太网端口，4个万兆SFP+，单子卡槽位，PoE+，含1个500W 交流电源)S5720-56C-PWR-EI-DC(48个10/100/1000Base-T 以太网端口，4个万兆SFP+，单子卡槽位，PoE+，含1个650W 直流电源)S5720-56C-PWR-EI-AC1(48个10/100/1000Base-T 以太网端口，4个万兆SFP+，单子卡槽位，PoE+，含1个1150W 交流电源)2端口万兆SFP+接口板(S5720EI 系列使用)2端口万兆RJ45接口板(S5720EI 系列使用)8端口万兆SFP+接口板(S5720EI 系列使用)8端口万兆RJ45接口板(S5720EI 系列使用)2端口QSFP+接口板(S5720EI 系列使用)S5720EI 风机盒(F ，风机盒面板侧进风)RPS1800 冗余电源150W AC 电源模块150W DC 电源模块500W AC PoE 电源模块650W DC PoE 电源模块1150W AC 电源模块订购信息S5720-EI 系列以太交换机主机选购一览表：10华为企业Sx700系列交换机版权所有 © 华为技术有限公司 2015。