船体和轮机常用英语单词汇总

合集下载

轮机英语词汇总结1~20章

轮机英语词汇总结1~20章

Lesson1:ships and machinery 专业词汇:naval architect造船工程师marine engineer轮机工程师hull 船体外壳propel推进steer 操舵anchor 抛锚cargo-handling 货物装卸vibration振动longitudinal纵向的transverse横向的deck甲板hatch 舱口hatch cover舱盖navigating bridge area 驾驶台communication centre通信中心stabilizer 减摇鳍container ship 集装箱船bulk carrier 散货船tanker液货船passenger ship 客船cruise ship 游船pilot vessel 引航船displacement排水量deadweight 船舶载重量light weight 船舶空船排水量installation 安装layout 布置gearbox 齿轮箱direct-couple 直接传动diesel engine柴油机team turbine 蒸汽轮机propeller 螺旋桨prime mover原动机crankshaft 曲轴cylinder 气缸auxiliary辅助的generator发电机air compressor 空压机evaporator 造水机heat exchanger 换热机boiler 锅炉funnel烟炊twin-screw双螺旋port左旋starboard 右旋waste combustion plant 焚烧炉bulkhead 船舱壁metric米制的公制的tug 拖船非专业词汇:vehicle 交通工具habitability可居住性overlap 重合ores 矿石arbitrary 任意性distinct 清楚的独特的endure 持续度过self-sustaining 自稳定自维持Lesson2:how does a marine diesel engine work 专业词汇:internal combustion engine内燃机ignite 点燃injection喷射chamber腔室piston活塞spray 油雾cycle循环sequence顺序stroke 冲程alternator 交流发电机aspirate吸入atomized 雾化的auxiliary 辅助的blow 吹,鼓风draw 抽吸centripetal 向心的chamber 腔,室charge 填充物combustion 燃烧compress压缩crank 曲柄crankshaft 曲轴crankpin 曲柄箱cylinder 气缸diesel 柴油机exhaust 排出,耗尽,废气fine细小的generator 发电机ignite 点燃induce 引起,招致inefficient 效率低的inhale 吸入inject 喷射injector喷射器inlet 进口marine海运的,船用的piston活塞principle 原理,原则propeller螺旋桨,推进器propulsion 推进residual 残留的,剩余的revolution 转rotate 旋转scavenge扫除,吹除timing 定时turbocharge 涡轮增压turbocharger 涡轮增压器bottom dead centre (BDT)下止点top dead centre(TDC)上止点loop scavenge 回流扫气uniflow scavenge 直流扫气reduction gear box 减速齿轮箱slight ram 进气阀座connecting rod 连杆blade 叶片非专业词汇:adjacent邻近的application 请求,应用closure 关闭encourage 促使fresh 新鲜的inlet 进口medium 中间的,介质operation 操作,过程poppet 提升retard 推迟vast 大量的Lessen3 diesel engine construction 专业词汇:adjustment 调节annular 环形的assembly 组件bearing 轴承bedplate 机座bolt螺栓bore 钻孔channel 通道clearance间隙component 部件diameter 直径dowel 销钉drill 钻孔duct 管道emission 散发,喷射film 油膜flange 法兰forge 锻造frame 机架groove槽,沟guide导板indicator 示功器jacket 夹层joint 接口liner 衬套maneuverability 机动操作性,机动性mount 安装pin 销子reliability 凹槽scraper 刮油器screw 螺钉seating 座,底座shim 垫片shoe 滑块slot 开槽stud 双头螺栓weld焊接carrier ring 承磨环cast iron 铸铁chain transmission 链条传动white metal 白合金stuffing box 填料箱非专业词汇:deformation变形rigid 刚性的,坚实的rubber 橡胶horizontally 水平地adequate 足够的advanced先进的chromium镀铬construction结构displace 错位integral 整体的precise精确的reliability 可靠性rotary旋转secure固定topmost最上部vertical垂直的vital至关重要的Lesson4 fuel oil system 专业词汇:catalyst催化剂catalytic催化剂的centrifuge分油机cavitation 气穴现象contaminate污染contaminate杂质deaerate除气,除氧impurity杂质,混杂物overflow溢流overhaul大修pressurize增压,密封purifier分水机clarifier分杂机refinery炼油厂rust铁锈safeguard维护,保护措施black-out全船停电booster pump增压泵gasway气道in parallel并联in series串联residual fuel渣油fuel oil燃油diesel oil柴油daily service tank日用柜viscosity粘度preheater预热supply pump驳运泵maintenance维护setting point倾点water content水分cleaerate放气flash point闪点specific gravity比重valve seat阀座bar大气压filter滤器非专业词汇:component元件,构件consumption消费量conventional常规的delivery传递,输送provided倘若irrespective不考虑的Lesson5 central cooling water system专业词汇:Chest 箱,柜deaeration除气malfunction故障scoop收集器,吸入口standstill停车thermostatic恒温的by-pass旁通管expansion tank 膨胀水箱volume体积alarm device 报警装置shipyard船厂非专业词汇:Accomodate 收容,装有additional另外的alternatively备用地integrate使成整体,结合Lesson 6Reservoir 容器Drainage 放残Interlock 连锁Non-return vavle 单向阀Pilot air 控制空气Pneumatic 气动Vent 放气Ahead/astern 进车/倒车Deposit 沉积物Ignite 点燃Flame trap 阻焰口Relief vavle 安全阀Bursting cap 防爆门Fusible plug 易熔塞Air distribution 空气分配器Engage/disengage 啮合/脱离Humidity 湿度Suck in 吸收Isolate 隔离Manoeuvre 操纵,机动Provision 备件Reluctant 冗余的Drawn from 来自Stringent 严格的Bore 孔Correspond 相应的Whilst 当什么时候Occurrence 事故Lesson 7Oil film 油膜Neutralize 中和Acidic product 酸性产物Considerable 相当多的Resist oxidation 抗氧化Wear detritus 磨削Total loss system 不回收系统Circulating system 循环系统Line wall 气缸壁Piston ring belt 活塞环带Carry Out 实现完成Quill 注油针阀Residual fule 渣油Corrosive 腐蚀的Lacquer 漆Alkalinity 碱Detergency 去垢能力Property 性质Rupture 破裂Crack 裂纹Slump 油底壳In duplicate 双联Level guage 液位表Drain tank 循环柜Impinge 射到Counteract 克服Impart 给予Reversal 相反的=Lesson 8Naturally aspiration 自然换气Exhaust gas turbocharging 废气涡轮增压Induce 参与Manifold 总管Volumetric efficiency 容积效率Turbine blade 增压机压片Adjacent 邻近的Swirl 漩涡Opposed piston 对置活塞Constant pressure system 定压增压Pulse system 脉动增压Thermal loads 热负荷Cross flow scavenge 横流扫去i Loop flow scavenge 回流增压Uniflow scavenge 直流扫气Blower 鼓风机Simplify 简化Lesson 10Thrust 推力Intermediate shaft 中间轴承Tail shaft 尾轴承Sterntube 尾轴管Cone 螺旋桨轴帽Mounte 安装Integral/independent 整体式/独立式Cate for 满足Shock load 冲击性负荷Thrust block 推力块Fitted bolt 紧固螺栓Bearing pad 承压块Pivot 支点,枢轴Tilt 倾斜Thrust Collar 推力环Oil scraper 刮油器Fabricate 铸造Aftermost tunnel bearing 尾轴管轴承Jounal bush 轴瓦Oil thrower ring 甩油环Gland 机械密封Outboard/inboard 舷外/内Stuffing box 填料箱Bulkhead 舱壁Lip seal 唇封Radial seal 径向密封Mate 配对Ingot steel 钢锭Taper 变细Fixed pitch propeller 定距桨Controlallable pitch propeller 变距浆Static 静态Dynamic 动态Lesson11直径Diameter半径radius孔,镗孔bore 行程stroke 平均有效压力MEP平均活塞速度mean piston speed 比燃油消耗率SFOC共轨common rail传统的conventionl 可用的available电磁阀magnetic valve/ solenoid valve 可靠性reliability耐用性durability精确地precisely精确的precise灵活地flexibly消耗consumption优化的optimized排放mission机动性maneuverability大修over hauls烟灰soot变量,可变的variable备份back-upLesson15轴向的axial离心的centrifugal水库,水柜reservoir安全阀relief valve容积volume排出的delivery排出阀discharge valve吸入阀suction valve空气室air vessel椭圆的elliptical螺杆screw双作用double acting往复泵reciprocating displacement pump 自吸self-priming维护,保养maintenance放残draining回转式容积泵rotary displacement pump 程序procedure轴封shaft sealing密封装置packing arrangement磨蚀abrasive腐蚀corrosive叶轮impeller外围periphery填料箱式packed gland转子element机械轴封mechanical seal耦合室coupling spacer紧tight导轮diffuser套筒drum串联in seriesLesson10Transmission SystemThrust shaft推力轴Intermediate shaft 中间轴Tail shaft 尾轴Thrust block推力轴承Thrust collar 推力环Lip seal 唇形密封Head tanker高置油箱Thread 螺纹Back press背压Boss 桨Pitch 螺距Radial face seal 径向面密封Fixed pitch propeller定距桨Stern tube bearing 尾轴管轴承Controllable pitch propeller变距桨Bearing pad 推力块Integral 完整的Cone 锥形物推冒Rudder 舱Hull 壳体Fitted blot 紧配螺栓Pivot 支点Tilt 使倾斜Scraper 刮油器Cascade 分布Fabricate 焊接Aftermost 靠近船尾Bush 轴瓦Tunnel 轴遂Thrower ring 甩油环Dip 浸入Lignum vitae铁梨木Timber 纤维Axial 轴向的Radial 径向的Stuffing box填料箱Helicoidat 螺旋面Blad 桨叶Rigid 刚性的Cascade 倾泻Lesson11 A leap in technology for marine enginesMagnetic valve 电磁阀Part load 低负荷Emission 排放Strock 行程Mean piston speed 活塞平均速度SFOC燃油消耗率Bore 缸孔Coastal 海岸的Diminish 使减少Dredger 挖泥船Leap 飞跃Optimal 最理想的Optimize 使最优化Precise 精确的Vital 至关重要的Back up 备份Lesson12 ME EnginesActuator 执行器Boester 升压器Diognostics 诊断Governor 调速器Hydraulic 水力的Inclination 倾斜Mechatronic 机械电子的Mesh 网孔Momentum 动力Proprietary 专利的Servo 伺服Counterpart对应物LESSON13 marine boilera and their constructionAttemperator 保温装置Casing 包装Conrection 传送对流Downcomer 下水道Furnace 炉子Gastight 不漏气Mounting 设备Propulsion 推力推进力Spherical 球型的Tangent 接触的Refractory lining耐火Saturated steam 饱和蒸汽Steam generation 蒸发Lesson14boiler mountings management and maitentBilge 舱底Condensate 冷凝物Bulge 不规则突起Detritus 碎石Dislodge 驱逐Fracture 破裂Friable 易碎的、Gauge 测量Periodically 优先的Salinity 盐分Sludge 淤泥Sample connection 取样口Soot blower 吹灰口Steam trap 凝气口Lesson15 marine pumpAxial flow pump 轴流泵Screw displacement pump 螺杆泵Displacement pump 容积式泵Peciprdate 螺杆泵Impeller 叶轮Volute 蜗壳Pump element 泵转子Priming umit引水单元Self-priming自吸Multi-stage多级Vane 叶片Wearing ring 承磨环Suction pipe 引入管NPSH汽蚀余量Configuration 构造Equilibrium平衡Pipe work 管系Alternately 交替的Valve arrangement阀组Air vessel空气室Dampen 减弱Vaper 水蒸气Entrained 引入空气Seizure 卡住Ridge凸台Erratically 不稳定Ground in 研磨Nesh 啮合Abrasive 磨蚀的Covrosive 腐蚀的Strip 拆开Bracket 支架Diffuser 导轮Coupling spacer耦合室Reservoir 储存器Lesson16marine refrigerationRefrigerant 冷剂Condenser 冷凝器Sub-cooled过冷Super heat 过热Evaporator 蒸发器Liquid receiver 储液器Drier 干燥器Unloading gear 卸载机构Hermetic 封闭的Semi-hermetic 半封闭的Oxide 氧化Brine 盐水Carbon dioxide二氧化碳Compact 紧凑的Bulb 湿包Fin 肋板Pass over 在上面流过Pass through 在里面穿过Ventilation 通风Solenoid valve 电磁阀Sub—devided 细分Rotor 螺杆Star wheel 星形轮Pitch 倾斜Fan 风机Coin 盘管Hunt 震荡Baffce 挡板Solenoid 螺线管Elastomer 弹性体Lesson17 marine refrigeration management and fault diagnosisLeak detector lamp检漏灯Concentration 浓度Liquid hammer水击Oil hammer油击Surplus 过多的Up right 直立Inclined 倾斜Violet 紫色Pale blue淡蓝Symptom 症状Press differential rely压差继电器Parge valve 放气阀Service valve 检修阀Duct 管子Under charge 冷剂不足Gauge 压力表Stem 阀杆Purge 放出Ascertain 确定Lesson20 Air Conditioning systemClimatic condition 气候条件Sufficient 足够充分Relative humidity 相对湿度Percentage 百分数Ratio 比例Vapor pressure蒸汽压力Absorb 吸收Heat source 热源Criculate 循环Renewal 补充Consume 消耗Single duct system 单风管系统Volume 容积Flexible 灵活性Tendency 趋势Incurs 引起Fabricated standard duct 预制标准尺寸风管Air terminals lined 空气终端管路Sound insulation material 隔音材料Centrifugal fan 离心式风机Driect expansion 直接膨胀Hermetic 气密的Thermostat 温度传感器Pnenmatic 气动型Capacity 载荷Stuffiness 不通风的Interval 每隔Grease 润滑Axial flow fan 轴流式风机Slight variation 微调Extreme weather 热带气候Tropical condition温和条件Intermediate weather极端天气Lesson19 Bilge Water Treatment SystemBilge water 舱底水Definition 定义Scope 范围Merely 仅仅Intermittent 断续Predictable 可预测Foresee 预见Soot water 吹灰冲洗水Leakage 泄露Detergent 洗涤剂Cat fine 催化粉末Soot 灰分Primary 第一级Particle 颗粒Portion 空间Emulsified 被乳化Organic solvent 有机溶剂Sludge 渣Nautical miles 海里Desposal 排放Legislation 立法Ecosystem 生态系统Constraints 约束Compactness 结构紧凑Droplet 滴Buoyancy 浮力Disperse 分散Immiscible 不融合的Shear 剪力Robust 耐用Adsorbent 吸附剂Polisher 洁油单元Zeolite 硅酸盐Capacity 能力Salinity 盐度Polymeric 聚合体Ultimate 根本上Primary 最初的Cross—flow membrane 横流膜Predicte 预期Filtration system 反渗透超滤系统Lesson20 Garbage Management and Biological Sewage TreatmentClinker 渣块Refuse 废物Dunnage 垫舱物料Crockery 陶器Comminute 粉碎Incinerator 焚烧炉Discharge 排出Authorize 批准In principle 原则上Engage 从事Comply 遵守Prescribe 规定Regulator 调节器Extended aeration process 充分曝气过程Bubbling 气泡Agitating 搅拌Bacteria 细菌Propagate 繁殖Thrives 兴旺Innocuous 无害的BOD生物需氧量Aerobic 好氧的Anaerobic 厌氧的。

船舶常用英语(一)汇总

船舶常用英语(一)汇总

船舶常用英语(一)汇总一、船舶类型常用英语ship, vessel 船,船舶boat, craft 艇sampan舢板, 小船manpowered boat人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushioncraft 气垫船hydrofoil水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelledship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck shipcargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-containership 全集装箱船semi-containership 半集装箱船multi-purposecontainer ship 多用途集装箱船general cargo ship/vessel/carrier杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber)carrier运木船cattle carrier 运牲畜船multi-purpose ship多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship(RO/RO ship) 滚装船ferry渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船;推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线,中线athwartships 横对船体(与船首尾线直交)bevel斜角;斜面base line 基线amidships 在船中部;在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点;交叉;横断面knuckle折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth;depth) 登记长度(宽度、深度)freeboard干舷rise of floor (dead; rise) 舭高;船底loadlinemark载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel (首尾)等吃水,平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation居住舱室accommodation deck 起居舱室;旅客甲板accommodation ladder舷梯accommodation ladder platform 舷梯平台accommodation laddermanrope 舷梯扶索after body 后(部船)体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage (船体水线下的)附体;附件auxiliary machinery 辅助机械;辅机balanced rudder 平衡舵ballast压载(物)ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱(水)batten 板条;压条(封仓用)batten-ceiling (货舱内)护舱条,护板beam横梁beam bracket 梁肘板bearding 交合线,榫(艏柱或艉柱上)bending moment 弯矩bilge 舭部;舱底;(船底)污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt系缆桩bollard 系缆桩;系船柱;双系柱bolster枕垫bonnet烟囱帽;机罩boom 杆;吊杆;桁;叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部;轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow船首,船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板;(三角)拖架breakwater挡浪板bridge桥;桥楼;驾驶台bulb angle 圆头角材bulbous bow 球形船首,球鼻首bulb stern 球形船尾bulkhead舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark舷墙bulwark plating 舷墙板bulwark stay舷墙扶强材bunker tank 燃料舱bushing衬套butt端接;残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber翘曲camber of beam 梁拱第 11 页共 45 页cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever悬臂梁capstan绞盘;绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯,舷门cat walk (油轮上的)天桥,步桥center girder 中底桁center strake 中央内底板chafing plate防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock导缆器;垫木clamp plate 夹板,压板cleat 羊角;系绳铁栓;防滑条coaming围板;舱口围板cofferdam隔离舱collar plate 封板collision bulkhead 船首舱壁;防撞舱壁第 12 页共 45 页companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation皱;槽形;波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口;切davit吊艇架;吊艇柱deck甲板deck beam 甲板横梁deckhouse甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick吊杆diaphragm隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱(物料);衬垫第 13 页共 45 页dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk (船内)应急通道engine bed 机座engine casing 机舱围壁escape scuttle (船内)应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) (油船)膨胀深井extension bracket 延伸肘板face plate面板fender碰垫;护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange折边flanged bracket 折边肘板flat keel 平板龙骨floor肋板folding door 折门forecastle deck 艏楼甲板fore peak tank (船的)首舱;前尖舱第 14 页共 45 页forward perpendicular 首垂线foundation底座frame肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔;放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈,垫料(集)密封垫general service pipe (G.S pump) 通用泵,总用泵girder桁材gooseneck(parity iron) 鹅颈头;吊杆弯头grating格子板;滑铁板ground tackle 锚泊索具gunwale舷缘;舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜(甲板下)gusset角板;扣板gutter (甲板)水沟;槽沟gutter angle; waterway angle (舷侧)排水沟角钢gypsy 绞筒(锚机绞车上的)第 15 页共 45 页handrail舷墙扶手hanging rudder; hinged rudder 吊舵;悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser绳索;大缆heel踵材;横倾hinged cover(door) 铰链盖(门)hold货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱第 16 页共 45 页hold stringer 舱内纵桁hopper漏斗;开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材(防挠材)hull船壳,船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板;衬板jack千斤顶jack ladder 绳梯Jacob's ladder 软梯;绳梯Joggled joint 折接;弯合joggling machine 折曲机keel龙骨keelblock龙骨墩keel line 龙骨线;艏艉线keel plate第 17 页共 45 页龙骨板keel rail (救生艇)艇底把手keelson内龙骨kingpost起重柱;将军柱knee肘板;弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal纵骨;纵材;纵桁longitudinal bulkhead 纵舱壁longitudinal bending纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug耳板main deck 主甲板main frame 主肋骨manhole人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽第 18 页共 45 页molded depth 型深mooring hole 导缆孔mooring post 系缆柱;岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口;槽口;刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam防挠振梁panting stringer 防挠振纵桁pillar支柱;墩pintle舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform平台plating壳板第 19 页共 45 页plimsoll mark 载重线标志poop艉楼;船尾poop deck 艉楼甲板port 舷门;舱门;(装货)口;窗;门;孔porthole 舷窗;(装货)舷门propeller; propellor 推进器;螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking(船体)横向挠度rail扶手;栏杆rolling横摇round of beam 梁拱round stern 圆(船)尾rudder舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针;舵栓rudder plate; rudder blade 舵叶;舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁;舵杆管rung (梯子)踏步;横档第 20 页共 45 页scallop扇形开孔scantling构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处;斜面;斜接scarf joint 斜(嵌)接scarf weld (斜面)焊接scarfing bracket 嵌接肘板scupper排水孔scupper pipe 排水管scuttle 舷窗;人孔(盖);小舱口盖seam焊缝;接缝section剖面section modulus 剖面模数semi-balanced rudder半平衡舵shaft轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage;trunk) 轴隧;地轴弄shedder plate 泄板;斜板sheer舷弧;偏航sheer strake 舷顶列板shell船壳;壳shell frame 舷侧肋骨shell plating 船壳板;外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板(散装谷类);防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid护舷木;垫板skylight天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot槽;开缝sluice水密门;水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe测量管;测深管stabilizer减摇装置stabilizing tank 减摇水舱staging 构架;台架;脚手架stanchion支柱;栏杆柱static load 静载荷stay 支柱;撑条;支索stay bar(or rod) 撑杆stay plate 撑板stem艏;艏柱;艏材stem post 艏柱stern船尾,艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材;扶强材;加固物stool托架,座,凳strake列板strength calculation 强度计算strength deck 强力甲板stringer纵桁stringer plate 甲板边板structural member构件structural strength 结构强度strum box (舱底水)过滤箱strut 撑材,支柱,轴架stuffing box 填料箱superstructure上层建筑tail (end) shaft 艉轴tarpaulin 防水油布,帆布,舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板,牵板,连接板topside tank 顶边舱;上边柜topside tank sloping plating 顶边舱斜板torsion扭转torsion strength 扭转强度transom stern 方形船尾transverse横梁,横材transverse bulkhead 横舱壁transverse frame 横肋骨,横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧,隧道,风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管(孔)ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate上(下)支架板upper (lower) stool 上(下)托架ventilator通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁,挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁,桁板横梁web frame 加强肋骨,框架肋骨,桁板肋骨web plate 腹板wedge楔木,楔子winch起货机winch-head绞车卷筒windlass起锚机wing tank 翼舱,翼柜wire clip 钢缆夹wire reel 卷缆车,钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material(造船材料)T-bar T型钢Z-bar Z型钢I-Bar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转;扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性,可塑(锻)性flexibility 挠性,柔性,易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性,稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化,淬火tempering 回火casting 铸件,铸造forging 锻件,锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层,表面处理coating 涂层,敷料corrosion 腐蚀,侵蚀wastage 损耗,蚀耗wear and tear 蚀损,磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀,锈斑indent 凹痕,凹陷groove 槽沟detachment 脱开,脱焊rupture 断裂,破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准,校直snip 剪断,剪片taper 削斜,斜度B.Shipbuildingworkmanship (造船工艺)Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊;断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊;长孔焊plug weld 塞焊;圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut (焊接)咬边;根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability(curve)动稳性(曲线)entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩(应力)hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination;list; heel 纵倾longitudinal stability 纵稳性panting (波浪对船体的)冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩(应力)seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头(力)statical stability (curve) 静稳性(曲线)surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头(力)transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横(纵)稳心transverse (longitudinal) stability 横(纵)稳性trim by the bow (stern) 首(尾)倾turning quality (circle) 回转性(圈)velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition情况良好2.in poor condition情况欠佳3.in bad condition 情况不佳,情况不良4.in a neglectedcondition 缺乏保养5.not properly serviced未经正常保养6.not properly cleaned未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热(或电气绝缘)9.not properly adjusted未经正常校正10.defective 有缺陷的(失效)11.damaged损坏damaged beyondrepair 损坏了无法修复12.failed (in failure)失效13.cut of order (in trouble)故障out of action 停止工作(作用),不是指故障14.in disorder 零乱(船属具零乱了)15.not working 不能工作16.inoperative 不能工作(失效)unworkable, inoperable 指本身不能工作,在损坏状况判断中不能使用17.out of function 不能工作,失去作用,不起作用18.unserviceable (useless)不能使用(指必须换新的损坏部件)19.could not bestarted(failed to start)不能启动20.empty 空的21.fitted incorrectly安装不正确(指小型的装置设备)installed incorrectly 安装不正确(指较大的装置设备)22.dangerousaccumulation ofinflammable vapors可燃气体危险集积it was obvious that this state had existedfor a considerable time(损坏)状况是长期存在的23.sluggish in (action,answering) (动作、应答)迟钝B.Deficiencies1.no…fitted,no…provided 未装2.no…available未备有3.missing遗失4.incomplete 不齐全,不完整5.deficient不足,缺少6.insufficient不足7.neglected遗漏8.omitted遗漏,省去9.removed移开,拆走10.washed overboard冲走11.dropped跌落12.fitted with wrong ….(size, material,devices…)错用(尺寸,材料,仪器)C.Tightness, stains, lossof etc.1.Leaking漏2.infiltrating (seeping)渗漏3.weeping泪滴4.sweating汗滴5.not watertight不水密6.loss of watertightness失去水密性(比5好)7.loss of airtightness失去气密性8.loss of oiltightness失去油密性9.escaping of cool逃冷10.loss of lub-oil pressure滑油压力降低11.loss of water pressure水压力降低12.oil polluted油污染13.oil soaked油浸14.water soaked水浸15.water stained水渍16.oil stained油渍17.rust in patches锈斑18.verdigris in patches铜绿斑19.water marks水渍D.Crack, score, breaketc.1.scuffed 拉毛(仅从反光上可观察到)2.chafed擦痕3.scored 拉痕(痕较chafed深)4.scratched 抓痕(硬拉过的痕)5.scraped 刮痕(长期运行刮的痕)6.grooved 槽痕(比pitting深)7.ridged 凸起雷治痕(环状的痕)8.cracked裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped龟裂,折裂10.fractured折裂11.broken off 破掉(破裂后跌落)broken 破裂,破碎12.holed穿洞13.holed & flooded破洞浸水14.opened开口15.bent弯曲16.canted倾斜17.buckled皱折18.warped翘起,翘曲19.indented (dented)凹痕,凹陷(指船壳板在两档肋位间的凹陷)20.set in 凹陷(指船壳板较大面积的凹陷)21.waved波曲22.curled 卷曲(指绳索)23.rumpled 褶皱(指垫片)24.bulged 鼓起,凸出25.collapsed 倾陷,倾倒26.ruptured毁损27.torn off撕破torn拉脱28.pierced刺破29.peeled 剥皮(油漆剥落)30.burst 爆破(指高压管路)31.blown off (packing)吹脱32.distorted 扭曲,歪扭33.engine break-down因故障机器突然停车E.Corrosion, seizing,choking etc.1.corrosion腐蚀2.wasted耗油3.deteriorated蚀薄4.thinned变薄5.pitted麻点6.eroded侵蚀7.rusted生锈8.rotten (木、橡胶)腐烂、腐坏9.decayed (电缆)腐烂、腐坏10. aerated(橡胶、电缆)腐烂、腐坏11. aged老化12. seized咬住13. seized by corrosion锈死14. stuck (粘)咬住15. rust-jammed锈轧16. fouled拥塞17. clogged堵塞(常指管子的堵塞)18. blocked阻塞19. gagged塞口20. foul & dirty闭塞21. blanked封没22. plugged闭塞23. choked 卡住,阻塞F.Wear, loose, clearanceetc.1.Loose松动2.starting(铆钉)松动3.slack松动slack back松出4.worn磨损5.worn cut evenly均匀磨损6.worn cut unevenly不均匀磨损7.worn on one side单边磨损8.worn outsymmetrically 对称磨损9.distorted (轴线弯曲并扭转)扭曲10.sprung(铆钉)扭歪11.twisted (轴线未弯、纯扭转)扭转12.excess clearance间隙过大13.excess backlash齿隙过大14.excess vibration振动过大15.excess noise level噪音过大16.loose engagement啮合太松17.loose connection接头松动18.tooth齿worn out 磨损chopped off 崩缺fractured折断19.knocking敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal轴承合金detached脱壳cracked开裂wiped铺铅belted熔化oil groove blocked 油槽堵塞21.out off roundness失圆22.out off alignment拉线不直23.off-centering偏心24.deflected偏斜G.Burning, heating, etc.1.Sparking火花2.arcking (arcing)电弧mutator整流器scored拉痕burnt烧坏worn 磨耗,磨损uneven不平sparking火花blackened发黑rough粗糙mica undercut弧坑4.brush set incorrectly碳刷安装不正确5.scorched烤焦6.coked结焦7.charred结碳8.overheated过热9.broken down击穿10. short-circuit短路11. setting incorrect 整定值不正确12. tripped incorrect脱扣不正常13. batteriescompletely discharged(电)完全发光undercharged未充满overcharged充电过量dry water水干第 41 页共 45 页A. Remove, crop etc.1.Removed拆下2.removed & replaced拆装3.removed, faired &replaced拆装拷平4.cropped & renewed割换(管、板、栏杆)5.partly renewed部分换新6.partly cropped &renewed 部分割换7.cut off割除8.faired拷平9.faired on原地拷平10.faired in place原地拷平11.straightened拷直、校直12.dismantle 拆卸(某一零件)13.disassembled拆散(解体)14.stripped 拆除(某一部件)15.unshipped拆下16.disconnected 断开(线、管接头)17.opened打开18.lifted抬升、举起19.jacked 顶起(用千斤顶顶起)20.replaced (by, with)换用21.patch贴补B.Fit, scrape, grind etc.1.fitted & scraped拂刮第 42 页共 45 页2.fitted & ground拂磨3.scraped & ground刮磨4.made to fit 拂合(装配好)5.run to fit 跑合(运动磨合)6.ground round磨圆7.ground smooth磨光8.ground & reamed磨绞9.bored round镗圆10.planed smooth刨光11.polished抛光12.machined光车13.skimmed光刀14.finish machined精加工15.rough machine粗加工C.Re-metal, adjust,check etc1.Remetalled重浇白合金2.re-babbitted重浇白合金(专指巴氏合金)3.pulled out拉出4.drawn out抽出5.taken out取出6.adjusted调整,校正adjusted for alignment 校正拉线adjusted true第 43 页共 45 页校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned清洁9.wire-scrubbed 钢丝刷(除锈)10.chipped & scraped拷锈(油漆)11.measured & recorded测量并记录12.logged (hourly)记录(小时)D.weld, rivet, wind etc.1.repaired by welding电焊修理2.welded补焊、焊接3.closed up by welds(面积、深度、高度较大)焊补4.built up by welds堆焊5.plug welded塞焊6.spot welded点焊7.butt welded对接焊第 44 页共 45 页8 tackweld 点焊、平头焊、定位焊第 45 页共 45 页。

船舶轮机英语单词总结

船舶轮机英语单词总结

船舶轮机英语单词总结A layer of lubricant 润滑层abrasive 有磨蚀的accommodation 住舱accommodation ladder 舷梯accommodation 居住舱室Accomplish 完成,达到,实现activate 使活动,起动Adjustment 调整Administrative offices 管理办公室adopt 采用advantage 优势,优点,效益应用affect 影响Aforesaid 上述的,前述的(常用于法律文件)aft ballast tank 艉压载舱Aggregate 合计,总计air cushion craft 气垫船air draught 水面上高度air pipes,sounding pipes and overflow pipes 空气管、测量管和溢流管路alarm 警报器alkalinity 碱度,碱性all duties pump 总用泵alloy 合金alternative 替换物,选择对象alternator 交流发电机aluminum 铝Aluminum 铝among 在……之中Analyze 分析anchor 锚anchor arrangement 锚泊设备anchor bell 锚钟anchor hoisting winch 起锚绞车anchor light 锚灯Anchorage 锚地Anchor-heaving trial 抛锚试验anti-corrosive oil 防腐油Aperture 孔,穴Applicant 申请者Applicant 申请者application 应用application 应用,运用Approach 方法,步骤,途径Appurtenance 辅助的设备,附属设备,配件Aptitude (特殊)才能,适应性Arbitration 仲裁around 在……周围,绕过arrangement 布置,安排,装置,方案aspect 方面Assembly line 装配(流水)线Assembly 装配assembly 组件,组装Assign 分配,指派assigning 确定,指派assist 帮助,协助atmospheric 大气的atomization 雾化attach 缚,系,附,归属attached pump (主机)附带泵attractive 吸引人的,引起注意的audible 听得见的automobile n. 汽车auxiliary engine 发动机auxiliary pump 辅助泵axial flow pump轴流泵axial flow 轴流式axial plunger pump轴流柱塞泵axial 沿轴的,轴的axis 轴balance 平衡Balance 平衡ballast (船等)压载物ballast pump 压载泵ballast tank 压载舱barge 驳船barge-carrier 载驳货船be adjacent to 靠近,接近be attached to 附属于Be built to order 按定单建造,按定货单制作be confined to 被限于……be divided into 分成be made up of…由……构成bearing 轴承bedplate 基座bell 钟,罩Bench work 钳工Bid 投标bilge piping and ballast piping 舱底水与压载管系bilge piping system of cargo pump rooms and cofferdams 货泵舱和隔离空舱舱底水系统bilge pump 舱底水泵bilge 舭bilge 舱底(水)bilge 舱底,船舱积水Bind 约束blade 叶片,桨叶blank 隔开、封着,使无效Blast 喷丸(除锈)blind-flange 盲板法兰Block 墩木,块,阻塞block 块boat deck 艇甲板Body plan 横剖型线图,正面线图body 主体boiler feed and blow off pipes 锅炉给水和泄放管boiler fuel oil system 锅炉燃油系统Bollard test,dock trial 系泊试验bolt 螺栓,用螺栓固定boom length 吊杆长度boom 吊杆Boom 吊杆boost(er) pump 增压泵bottom dead centre (BDC ) 下止点bow 船首bower anchor 首锚Bracket 支架,托架brake horsepower 制动马力,制动功率brake 制动器,刹车branch 分支,支管brazing 铜焊(接)Bridge crane 行车,桥式起重机bridge deck 驾驶甲板Bridge 桥楼brittle 易碎的,脆弱的bronze 青铜(铜与锡合金)Brozen sleeve 青铜筒套buffer tank 缓冲柜buffer 缓冲器,贮存装置Building basin 船台Building period 建造周期built-in 内装的,机内的,固定的bulk-carrier 散货船bulkhead 舱壁bulkhead pieces 舱壁部分bulkhead 舱壁bulkhead 隔壁,防水壁bulwarks 舷墙Burner 气焊工bursting pressure 爆炸压力by comparison 通过比较cabin deck 起居甲板cable releaser 弃链器cablelifter 锚链轮Calorific 卡的,热量的,发热的calorific 热(量)的,发热的cam clearance 凸轮间隙Camber 拱形cap 盖capstan 绞盘,绞车captain deck 船长甲板carbonaceous 碳的Cargo capacity 载货量,货舱容量,舱容cargo handing gear 起货设备cargo handing productivity 装卸能力cargo oil piping system 货油管系cargo oil suction 吸油口cargo space 货物舱位cargo winch 起货绞车Carpenter 木匠carrier ring 承磨环casing 箱,外壳cast steel chain 铸钢锚链casualty 灾祸,意外catalytic 催化的catamaran 双体船category 类别cause 原因,引起central cooling system 中央冷却系统centralized control 集中控制centrifugal oil separator room 分油机室centrifugal 离心的centrifuge 离心(分油、净油)机centrifuge 离心分离机cetane 十六烷值chain cable compressor ,chain stopper 止链器chain cable 锚链chain link 锚链环chain locker 锚链舱chain pipe 锚链管chain winch 锚链绞车Charge 费用charge 装,充chemical carrier 化学品(运输船)Chipper 风铲工,缺陷修理工chock 塞块,楔型垫chromium 铬circuit 回路,管路,电路circulating lubricating oil tank 滑油循环舱circulating pump 循环泵circulating tank 循环柜Class notation 船级符号Class symbol 入级符号class 等级cleanse 清洗clutch 离合器clutch 离合器cock 开关,龙头Coefficient 系数cofferdam 隔离空舱Collapse 毁坏collecting tank 收集柜Collision 碰撞Combat system 作战系统combustion 燃烧,焚毁,发(点)火commercially 商业上Compact 紧凑的compare 比较,对比Compartment stuffing box 隔舱填料函compartment 隔间,隔室Compass adjuster 罗经校正员compass deck 罗经甲板Compel 强迫compensate 补偿Competitive 竞争的Completion 完成Complex 复杂的,合成的,综合的complexity 复杂,复杂性component 元件,组成元件compound-supercharged diesel engine 复合式增压柴油机compressed air piping system 压缩空气系统compression (发动机,如内燃机中工作液体的)压缩compression pump 压缩泵Compromise 折衷,调和Compulsory 强迫的,强制的,义务的Concrete 混凝土condensate and exhaust steam piping 凝水和乏汽管系Configuration 构造,结构,配置,外形considerable 相当的,大量的constitute 构成construction 结构Consult 咨询Consumable 消耗性的Consumable 消耗物品consumption 消耗,消费contact 接触container 集装箱container ship 集装箱船container ship 集装箱船container 集装箱,容器,壳,罩containerization 货柜运输contamination 污染(物)conventional 常规的,惯例的convey 传递coolant 冷却剂copper n. 铜copper 铜corrosion 腐蚀,锈corrosive 腐蚀(性)的corrosive 腐蚀的,腐蚀性的counteract 克服coupling 联接,联接器,联轴节Course keeping test 航向稳定性试验Craft 船,手工艺Crane operator 起重工crane 克令吊,起货机crane 起重机crankpin 曲柄销Criteria 准则,标准,规范cross 十字的,交叉的crow’s nest 桅上瞭望台crown 冠,顶部,活塞crows nest 瞭望台crude oil 原油cruiser 游船Culminate (与in连用)达到。

船体和轮机常用英语单词汇总

船体和轮机常用英语单词汇总

船体aircraft carrier 航母submarine 潜艇air cushion vehicle 气垫船longitudinal strength 总纵强度transverse strength 横向强度local strength 局部应力hull 主船体superstructure 上层建筑stem 船首midship 船中stern 船尾forecastle 首楼brige 桥楼poop 尾楼deck house 甲板室ship bottom 船底ship side 舷侧upper deck 上甲板lower deck 下甲板transverse bulkhead 横舱壁longitudinal bulkhead 纵舱壁forepeak bulkhead 首尖舱壁afterpeak bulkhead 尾尖舱壁shell plate 外板seam 边接缝butt 端接缝strake 列板bottom plate 底板plate keel 平板龙骨bilge strake 舭列板side plate 舷侧外板sheer strake 舷顶列板second deck 第二甲板third deck 第三甲板platform deck 平台甲板deck plate 甲板板deck stringer 甲板边板sponson deck 舷伸甲板center keelson 中内龙骨side keelson 旁内龙骨T-bar T型材web 腹板bracket 肘板face plate 面板flange 折边板floor 肋板bilge bracket 舭肘板bulb plate 球扁钢angle bar 角钢bottom center girder 中底桁bottom side girder 旁底桁solid floor 主肋板watertight floor水密肋板bracket floor框架肋板lightened floor 轻型肋板stiffener 加强筋reverse frame 内底横骨bottom frame 船底肋骨inner bottom plate 内底板man hole 人孔margin plate 内底边板duct keel 箱型中底桁pipe tunnel 管隧longitudinal 纵骨bottom longitudinal 船底纵骨inner bottom longitudinal 内底纵骨bottom side tank 底边舱foundation seating 基座shaft tunnel 轴隧tunnel recess 尾室emergency exit 应急出口bilge keel 舭龙骨frame 肋骨integrated barge 分节驳main frame 主肋骨tweendeck frame 甲板间肋骨intermediate frame 中间肋骨web frame 强肋骨side stringer 舷侧纵桁side longitudinal 舷侧纵骨cross tie 撑杆wing tank 舷边舱ballast water tank 压载水舱torsion box 抗扭箱bulwark 舷墙fender 护舷材beam 横梁deck beam 甲板横梁half beam 半梁hatch end beam 舱口端横梁deck girder 甲板纵桁hatch side girder 舱口纵桁beam knee 梁肘板deck longitudinal 甲板纵骨web beam 强横梁cargo hatch 舱口hatch coaming 舱口围板gusset plate 菱形板hatch side cantilever 悬臂梁piller 支柱topside tank 顶边舱excess hatch 人员出入舱口expansion trunk 膨胀井cofferdam 隔离空舱partial bulkhead 局部舱壁plane bulkhead 平面舱壁bulkhead plate 舱壁板tweendeck bulkhead 甲板间舱壁vertical bow 直立型首raked bow 前倾型首clipper bow 飞剪型首icebreaker bow 破冰型首bulb bow 球鼻型首fore peak 首尖舱collision bulkhead 防撞舱壁raised floor 升高肋板panting beam 强胸横梁wash bulkhead 制荡舱壁chain locker 锚链舱stem 首柱steel plate stem 钢板首柱combination cast and rolled stem 铸钢和钢板混合式首柱forged steel stem 锻钢首柱thruster 侧推器elliptical stern 椭圆型尾cruiser stern 巡洋舰型尾transom stern 方型尾after peak 尾尖舱shaft tube 艉轴管cant frame 斜肋骨cant beam 斜横梁stern frame尾柱rudder post舵柱propeller post 螺旋桨柱shoe piece 尾柱底骨propeller shaft strut 艉轴架A-bracket 人字架shell bossing 轴包套spectacle frame 眼镜形骨架accommodation deck 起居甲板boat deck 艇甲板navigation deck 驾驶甲板compass deck 罗经甲板compass plateform 罗经平台expansion joint 伸缩接头engine casing 机舱棚derrick post 桅柱derrick plateform 起货机平台tower post 塔式桅pressure hull 耐压舰体pressure structure 耐压结构non pressure structure 非耐压结构pressure conning tower 耐压指挥台pressure tank 耐压水舱pressure bulkhead 耐压舱壁oil ballast tank 燃油压载水舱conning tower sail 指挥台围壳exhaust valve 排气阀camshaft 凸轮轴crankshaft 曲轴crosshead 十字头connecting rod 连杆tie bolt 地脚螺栓轮机英语ashore 在岸上,陆地上shipchandler 船舶供应商saloon 大台,大厅,酒吧,展览会场,motorman 机工agent 代理cabin 舱室corridor 走廊brief discription 简短,简要的介绍domestic 国内的,家庭的|佣人,国货materials 材料installation 安装,装置marine diesel engine 船用柴油机horsepower 马力diesel 柴油cylinder 汽缸bore 钻孔,孔cylinder bore 缸径piston 活塞stroke 冲程,打击,笔画piston stroke 活塞冲程compressor 压缩机the oil-burning vertical type auxiliary boiler 立式燃油辅助锅炉automatic changover switch 自动转换开关marine animals and plants 海洋动植物compound 混合,化合物,混合物,妥协chemical compound 化学添加剂corrosive 腐蚀copper 铜aluminium 铝instruction manual 说明书Asian 亚洲人alien 外国的,相异的,性质不同的,外侨,转让the living expenditure 生活费用spare part 备件urgent 急切的,迫切的recall the order 取消订单surveyor 验船师leakage of fuel oil 漏油nozzle nap喷嘴帽injector 喷油器on the spot 现场B register of shipping B船级社bunkering 加油terminal 终点,终极oil company’s terminal 油品公司码头barge 驳船application 应用,申请store 储备,储藏high reputation 信誉好tempting 诱人的,吸引人的quote 引述,举证catalogue 目录bolt 螺栓freon 氟利昂brake 刹车expansion valve 膨胀阀air-mailed 空运Fax 传真whole threaded 全丝双头螺栓stud 大头钉screw pitch 螺距hexagon nipple 六角管接头washer 垫圈,洗涤器,洗衣人micrometer 千分表the wire stripping pliers 剥皮钳specification 规格invoice 发票tug 拖轮joint 接头the harbour office 港务局specific gravity 比重viscosity 粘度warranty 担保,保证,授权substitute 代替duplicate 复制,副本alongside 在旁边,在…旁边portside 左舷starboard 右舷hose 软管diameter 直径gangway 跳板,舷梯the fire hoses and equipment 消防管道和设备precaution 预防,警惕plug 塞住the deck scupper pipe 甲板排水管leakage泄露choke 窒息,堵塞dismantle 拆除tank 舱室trim 整齐,修整the temperature correction factor 温度修正系数acid number 酸值ash content 灰度main engine 主机fuel oil heater 燃油加热器pilot 引水员lube oil 滑油diesel oil 柴油revolution 旋转,革命,运行,循环the hydraulic valve 液压阀nitrogen 氮installation 安装,就职,装置the warm-up valve 暖缸阀the circulating lube oil tank 循环油柜filter 过滤器clamp 夹紧,固定住joint 垫子previous 以前的,早先的generator 发电机the prime mover 原动机liner 钢衬crack 裂缝turbochanger 涡轮增压器shift 轮班,移动,转变main air compressor 主空气增压器workshop 车间overtime work 加班foreman 工头the air cooler 空冷器abnormal noise 声音异常inlet/outlet 进口/出口supercharger 增压器the tube leakage 管子泄露the fouling脏堵the chemical cleaning equipment 化学清洗设备the air seal 气封felt 毡silencer 消音器disassembling 解体the cooling copper tube 冷却铜管the cooling ribs around the tube管上的散热翅片make-do with sth 凑合auxiliary engine 辅机cylinder 汽缸the cylinder head 缸头ground 研磨the inlet and exhaust valves 进排气阀trial 试验the end cover 端盖the valve seat 阀座piston ring活塞环crank 曲轴the crank bearing 曲轴轴承the oil sump 油底壳magnet 磁铁storekeeper 保管员the special tool 专用工具torque spanner 扭力扳手screw nut 螺帽loose 松的hydraulic tool 液压工具groove 槽the piston ring groove 活塞环槽gap 天地,缺口,空白machined 车削加工过storeroom 仓库the worn-out flare 磨损的喇叭口the bearing shell 轴承瓦the piston pin活塞销rag 破布bulletin 公告scraper ring 刮油环in triplicate 一式三份burr 毛刺crank bearing bushes 曲柄销轴瓦polish 抛光oilstone 油石oil sump 油底壳replenish the oil 加油the scavenger pressure 扫气压力the engine trial 试车surge喘振dismantle 拆卸fly-wheel 飞轮the up-side-down type 倒挂式oil filter 滤油器the indicator cock 示功考克crankcase 曲柄箱boiler 锅炉weld 焊接the blow-down pipe 排污管slope vessel 污水船the flue door 烟道drawing 图纸you can count on me 你可以放心the combustion chamber 燃烧室refractory line 炉墙peeled off 剥落high percentage of carbon 高含碳量the boiler automatic feed control 锅炉自动给水控制the combustion automatic control 燃烧自动控制low water level 低水位the light resistor 光敏电阻the ignition electrode 点火电极the ignition injector 点火油头the buoy for the water level control 水位控制浮子the scale is very thick 水垢很厚the relay for the high and low water levels高低水位接触器the insulating material of some wires was aged and peeled off 一些电线的绝缘层都易老化并脱落avometer 万用电表the solenoid valve 电磁阀flange法兰blind plate 盲板the oil way 油路scavenge the boiler 炉内扫气。

修船英语词汇(已排版)

修船英语词汇(已排版)

一、船体结构词汇AAccommodation 居住舱室Aft perpendicular 艉垂线Aft peak tank 艉尖舱Aft peak bulkhead 艉尖舱壁Air diffuser 空气扩散器Air hole 通风孔Air intake 进气口Aircraft carrier 航空母舰Airdrivenwater pump 气动水泵Anchor 锚Anchor arm 锚臂Anchor chain 锚链Anchor crown 锚冠Anchor fluke 锚爪Anchor link 链环Anchor mouth 锚唇Anchor recess 锚穴Anchor shackle 锚卸扣Anchor stock 锚杆Angle bar 角钢Angled deck 斜角甲板Antenna 天线Antirollingtank 减摇水舱Automatic sprinkler 自动喷水器Automatic ventilator 自动通风筒Auxiliary engine seating 辅机机座Auxiliary tank 调节水舱BBack of blade 叶背Baffle 挡板,隔板Baggage room 行李舱Balance weight 平衡锤Balanced rudder 平衡舵Ball bearing 滚珠轴承、球型布司Ball valve 球阀Ballast tank 压载舱Barrel 圆筒Base block 垫块Batten 长行护板Beam 横梁Beam knee 横梁肘板Beam bracket 横梁肘板Bearing 轴承Bearing seat 轴承座Bedplategirder 基座纵桁Bellmouthof hawspipe 锚链筒喇叭口Berth 软垫床Bicoloredlight 两色灯Bilge bracket 舭肘板Bilge keel 舭龙骨Bilge plating 舭肘板Bilge sounding pipe 舭部边舱水深探管Bilge strake 舭列板Bitt 单柱系缆桩Bitts 双柱系缆桩Blade (螺旋桨)浆叶Blade face 叶面Blade root 叶根Blade tip 叶梢Blockage 堵塞Boat davit 吊艇架Boat deck 艇甲板Boat fall 吊艇索Boat hook 艇吊钩,(舢板)挽钩Boatswain’s store room 帆缆库Bobstay 首斜桅拉索Boiler 锅炉Boiler bearer 锅炉基座Bollard 系缆桩Bolt 螺栓Bolt lock 插销锁Book case 书柜Boss (螺旋桨)轴毂Bossing 轴包架,轴毂Bosun store 帆缆库Bottom ceiling 舱底铺板Bottom center girder 中底桁Bottom frame 船底肋骨Bottom grating 船底垫板Bottom plate 船底板Bottom side girder 旁底桁Bottom side tank 边底桁Bottom transverse 底边舱Buoy tender 航标船Bow door 艏门(滚装船)Bowsprit (帆船)艏斜桅Bow structure 艏端结构Bow thruster 艏侧推Bower anchor 艏锚Box keel 箱型龙骨Brace 转帆索Bracket 肘板,三角板Bracket floor 框架肋板Brake 制动装置,刹车Brake band(lining)制动带,刹车带Brake crank arm 制动曲柄Brake hydraulic cylinder 制动液压缸Brake drum 刹车卷筒Brake hydraulic pipe 刹车液压管Breast hook 艏肘板Breadth 船宽Bridge 桥楼,驾驶台Bridge console stand 驾驶室集中控制台Buffer spring 缓冲弹簧Bulb plate 球扁钢Bulbous bow 球鼻艏Bulk cargo carrier 散货船Bulkhead 舱壁Bulkhead deck 舱壁甲板Bulwark 舷墙Bulwark plate 舷墙板Bulwark stay 舷墙支撑Buoyant box 浮箱Buoy 浮筒Buoyancy tank 浮力舱Butterfly screw cap 蝶形螺帽CCable 电缆、缆索Cable chock 导缆钳Cable drum 缆索卷筒Cable releaser 弃链器Cable winch 钢索绞车Cage 起货机操作室Camber 梁拱Cant beam 斜横梁Cant frame 斜肋骨Cantilever beam 悬臂梁Captain 船长Captain room 船长室Cargo 货物Cargo battens 货物护板条Cargo block 吊货滑车Cargo boom 吊杆Cargo chain 吊货短链Cargo fall,cargo runner 吊货索Cargo hatch 货舱口Cargo hook 吊钩Cargo hook shackle 吊货钩卸扣Cargo hook swivel 吊钩转环Cargo hose 货油软管Cargo runner lead block 吊货索导向滑轮Cargo winch 起货绞车Cast steel stem post 铸钢艏柱Cat walk 步桥(油船),栈道Catamaran 高速双体船Ceiling 室顶板Ceiling lamp 吊灯Cement 水泥Cement draining 水泥流水沟Center girder 中纵桁Center keelson 中内龙骨Centerline bulkhead 中纵舱壁Chock 导缆钳Circular mooring pipe 圆形导缆孔Chain axle 链轮轴Chain clamp 制链钳Chain cable fairlead 导链滚轮Chain cable stopper 制链器Chain controller 制链器Chain link 锚链环Chain locker 锚链舱Chain wheel 链轮Chain wheel shaft 链轮轴Chart 海图Chart light 海图灯Chart room 海图室Chart table 海图桌Chief engineer’s room 轮机长室Clear view screen 旋回视窗Clearance hole 通焊孔Cleat 系缆扣Cleat post 羊角系缆桩Clip 夹扣Clipper bow 飞剪型船首Closed mooring chock 闭室导缆钳Clutch 离合器Clutch hand wheel 离合器手轮CO2 fire extinguisher 二氧化碳灭火器Coat and hat hook 衣帽钩Cofferdam 空隔舱Collision bulkhead 防撞舱壁Column 立柱Common link 普通链环Communicating pipe 连通管Communicating tank 连通水柜Commuter 交通船Compass 罗经Compass deck 罗经甲板Compressed air bottle 压缩空气瓶Condenser 冷凝器Conductor tube 导管Connecting tank 连接水柜Connecting traverse 吊钩梁Container 集装箱Container ship(liner,vessel)集装箱船Control desk 操纵台Control console of main engine 轮机控制台Control valve 控制阀Cork 软木、软塞Corrugated bulkhead 槽型舱壁Coupling 接头(考贝令)Cover plate 盖板Cowl head ventilator 头颈型通风筒Cushion 软垫Crane 克令吊、起重机Crank 曲柄Crew 船员Crew’s bed room 普通船员寝室Crow’s nest 桅杆了望台Crew’s quarters 船员居住室Crew’s W.C 船员厕所Crosshead 十字头Cruciform bitts 双十字系缆桩Cruciform post bollard 单十字系缆桩Cruiser 巡洋舰Cruiser stern 巡洋舰式船尾Cup and ball joint 球窝关节Curtain 窗帘Cycloidal propeller 直叶推进器Cylinder 缸体、圆柱体DDamper 缓冲器Davit arm 吊臂(吊艇架)Davit hook 吊艇钩Day room 起居室Deadlight (舷窗灯)风暴盖Deck centerline 甲板中心线Deck framing 甲板骨架Deck flange of hawse pipe 甲板锚链孔凸缘Deck girder 甲板纵桁Deck house 甲板室Deck longitudinal 甲板纵骨Deck side line 甲板边线Deck stringer 甲板边板Deck transverse 强横梁(纵骨架式结构)Deep sea vehicle 深潜器;Deep tank 深舱Detent(stopper)棘爪、制链器Derrick 起重机、吊杆Derrick boom 吊杆Derrick fall 吊杆索Derrick post 吊杆柱Derrick rig 吊杆装置Desk lamp 台灯Destroyer 驱逐舰Detachable shackle 散合式连接卸扣Devil’s claw 链式制链器Diagonal stiffener 斜置加强筋Diesel engine 柴油机Direction finder 方位测定器Direction finder antenna 测向仪天线Dispensary 医务室Displacement 排水量Displacement type vessel 排水型船Distance line 张索Dock 船坞Domed bulkhead 球型舱壁Door curtain 门帘Door frame 门框Door handle 门把Door hook 门钩Door plate 门板Doorway 出入门Double bottom 双层底Double bottom tank 双层底舱Double hook 山字钩Double roller chock 双滚轮式导缆钳Doubling plate 复合板,加强板Down halyard 降帆索Draft 吃水Draft line 吃水线Draft mark 水尺Dragline 拉索Drain hole 流水孔\污水孔Drain well 污水井Drawer 抽屉Drawer handle 抽屉把手Dredger 挖泥船Drillship 钻井船Driving shaft system 传动轴系Drum 卷筒Drum flange 卷筒凸缘Dry cell 干电池Dry power container 干粉容器Dry power fire extinguisher 干粉灭火器Drying agent 干燥剂Dynamic supported craft 动力支撑型船EEccentric wheel 偏心轮Eccentric roller jacking device 偏心起升滚轮装置Echosounder回声测深仪器Electric motor 电动机\电马达Electric rudder gear 电动舵机Electric revolving crane 电动回转式起重机Electric motor windlass 电动锚机Elevating system,elevator 升降机装置Elliptical mooring pipe 椭圆型导缆孔Elliptical stern 椭圆型船尾Embarkation deck 登乘甲板Emergency exit 紧急出口Enclosed lifeboat 封闭式救生艇End open link 末_______端链环End shackle 末端卸扣Engine 主机\发动机Engine air inlet 发动机进气口Engine casing 机舱棚Engine foundation 机座Engine room 机舱Engine room opening 机舱口Engine room frame 机舱肋骨Engine room hatch end beam 机舱口端梁Engine room hatch girder 机舱口纵桁Engine telegraph 车钟Enlarged link 加大链环Enter guider (集装箱阁栅)入口导承Exhaust pipe (发动机)排气口Exhaust valve 排气阀Expanded bracket 延伸肘板Expansion joint 伸缩接头\波纹管Expansion trunk 膨胀井Eye plate 眼板F Face plate 面板Fairlead 导缆器Fan 鼓风机Fan vent 鼓风机排气口Fast craft 高速船舶Fender 护舷材Ferry 轮渡Filter 过滤器Fin 鳍\散热片Fin angle feedback set 鳍角反馈装置Fin box 鳍箱Fin shaft 鳍轴Fin stabilizer 减摇鳍Fire boat(fire fighting ship)消防船Fire extinguishing agent 灭火剂Fire fighting gun 消防枪Fire hose 消防水管Fire hydrant(fire plug)消防栓Fixed water fire extinguisher 固定式水灭火器Flange(flange edge)折边\法兰Flap 折板(滚装船首尾跳板)Flaptyperudder 襟翼舵Flat steel plate 扁钢Floating crane 浮吊Floating dock 浮船坞Flume tank 槽形水舱Flush valve 冲水阀Fly net 纱窗Flying passage 步桥(油船)Foam concentrate container 泡沫液容器Folding hatch cover 折叠式舱盖Foot brake 脚踏刹车Foot ring 地令Footrope 根缆Fore and aft stay 前后拉索Fore lower topsail 前下中桅帆Fore upper topsail 前上中桅帆Forecastle 艏楼Forecastle deck 艏楼甲板Fore peak 艏尖舱Fore perpendicular 艏垂线Forged steel stem 锻钢艏柱Forward draft mark 船艏吃水Framing 骨架Freeboard 干舷Freeing port 排水口Fresh water loadline 淡水载重线Fresh water tank 淡水柜Fuel box 燃油箱Fuel oil tank 燃油舱Fulload waterline 满载水线Funnel 烟囱GGaff 纵帆斜桁Gaff foresail 前桅主帆Gaff mainsail 主帆Gangway 舷梯Galley (船上)厨房Gas line valve 气管阀Gasket 垫圈Gasoline tank 汽油箱Gear 小齿轮Gearwheel 大齿轮General cargo ship 杂货船Girder of foundation 基座纵桁Goalpost 门型桅(柱)Goaheadand goback前进和后退Grating 防滑格子、格兰丁Gravity type boat davit 重力式吊艇架Guide rail 导轨Guide roller 导向滚轮Gunwale 船舷上缘Gunwale angle 舷边角钢Gunwale rounded thick strake 舷边圆弧后板Gusset plate 菱形板Guy 稳索Guyline 定位索Gypsy 链轮(锚机上的)Gyropilotsteering indicator 自动操舵操纵台Gyroscope 回转仪HHalf beam 半梁Half depth girder 半深纵骨Half rounded flat plate 半圆扁钢Half round steel bar 半圆钢Hand crank 手摇柄Handrail 手栏杆Hand wheel 手轮Handle 把手Hatch 舱口Hatch beam sockets 舱口梁座Hatch coaming 舱口围Hatch cover 舱口盖Hatch cover rack 舱口盖板隔架Hatch end beam 舱口端横梁Hatch side cantilever 舱口悬臂梁Hatch side girder 舱口纵桁Hatchway 舱口Hawsehole 锚链孔Hawse pipe 锚链筒Head rope 艏缆Heel piece 艏柱根Helicopter 直升机Helicopter deck 直升机甲板Highpressuresoft pipe 高压软管Hinge 铰链Hinged hatch cover 铰链舱盖Hinged stern door 尾部吊门(滚装船)Hogging 中拱弯曲Hold 货舱Hold ladder 货舱梯子Hold pillar 货舱内支柱Hook 钩Hook bolt 钩头螺栓Horizontal girder 水平桁Horizonatal stiffener 水平扶强材Hull 船壳Hull plank 船壳板Hydraulic cylinder 液压油缸Hydraulic pump 液压泵Hydraulic revolving crane 液压回转式起重机Hydrofoil 水翼Hydrofoil craft 水翼艇IIcebreaker 破冰船Icebreaker bow 破冰型船首Independent tank 独立舱柜Inflatable liferaft 气胀式救生筏Inflation valve 充气阀Inner bottom plate 内底板Inner door 内门(滚装船)Inner plate keel 内平板龙骨Integral tank 整体舱柜Intermediate frame 中间肋骨Internal combustion engine set 内燃机组JJack 船首旗Jack staff 船首旗杆Jack up drilling plattform 自升式钻井平台Jet 喷筒Jet foam ejector 泡沫灭火枪Jet pipe 喷管Jib 首帆,起重机的臂Jig 支架Joint 接头Joint shackle 连接卸扣KKeel 龙骨Kenter shackle 双半式连接链环King post 主柱Knee 肘板LLadder 梯子Ladder way 步梯Launch 下水Lavatory 洗手间Lead block 导向滑车Lead sheave 导向槽轮Leading edge 导边(螺旋桨边)Lever chain stopper 闸刀式制链器Length 船长Length overall 船总长Lifeboat 救生艇Lifebuoy 救生圈Lifejacket 救生衣Liferaft 救生筏Lifting hook 艇吊钩Light bulb 灯泡Light derrick 轻型吊杆Light hold 空舱Light load waterline 空载吃水Lightening hole 减轻孔Limbers board 舭部污水道顶板Linkage handle 联动把手Liquid bulk cargo carrier 液体散货船Liquid chemical tanker 液体化学品船Liquefied natural gas carrier 液化天然气船Liquefied petroleum gas carrier 液化石油气船Loding line 载重线Local strength 局部强度Locker 立柜Longitudinal 纵骨Longitudinal bulkhead 纵舱壁Longitudinal bending 总纵弯曲Longitudinally framed system 总纵强度Loud speaker 扩音器Lower deck 下甲板Luffing winch 变幅绞车MMain frame 主肋骨Main engine 主机Main mast 主桅Manhole 人孔Manhole cover 人孔盖Margin plate 边板Mast 桅Mast antenna 桅杆天线Mast clutch 桅座Masthead light 桅灯Mast house 桅屋Mattress 床垫Maximum breadth 最大宽度Merchant ship 商船Mess table 餐桌Mixer 混合器Molded breadth 型宽Molded depth 型深Molded dimension 船舶型尺度Mooring hole 系缆孔Mooring post 系缆桩Multianglefairlead 滚柱导缆器Multipurposecarrier 多用途船Mushroom ventilator 菇形通风筒NNavigation area 航区Navigation bridge 驾驶台Navigation deck 航海甲板Navigation light 航行灯Navigation radar 航海雷达Nitrogen bottle 氮瓶Nonreturnvalve 止回阀Nose cone 螺旋桨整流帽Notch 切口Nozzle 喷嘴Nut 螺母OOar 浆Oblique bitts 斜式双柱系缆桩Officer 驾驶员Oil filler 加油点Oil intake pipe 进油管Oil tanker 油船Open rail 栅栏杆Opening 开口Ore carrier 矿砂船Outboard motor 舷外机Outer jib 外首帆Outfitting 舾装Outrigger 舷外吊杆叉头PPaddle 浆Parting arrangement 强胸结构、抗拍击结构Panting beam 强胸横梁、抗拍击横梁Partition 隔板Passage 人行通道Patch board 堵漏板Patch bolt 堵漏螺杆Pillar 支柱Pin 销子Pitch 螺距Piston 活塞Piston rod 活塞杆Pitting 蚀损斑、氢气泡疤Plane bulkhead 平面舱壁Plate 平板Plate keel 平板龙骨Platform 平台Pontoon hatch cover 箱形舱盖Poop 艉楼Port 左舷Port light 左舷灯Portable foam fire extinguisher 手提泡沫灭火器Portal frame crane 龙门架式起货机Position stop 限位器Pressure gauge 压力表Project 探照灯Project davit 探照灯吊杆Propeller 螺旋桨Propeller cave 浆穴Propeller post 螺旋桨柱Propeller shaft bracket 尾轴架Provision store 食物储备室Pudding 软垫Pudding fender (护舷)碰垫Pump 泵Pump room 泵房PVC foamed plasticPVC 泡沫塑料QQuadrant 舵柄Quarter 居住区Quarter pillar 舱内侧梁柱RRadar 雷达Radar indicator 雷达指示器Radial davit 悬臂吊艇架Raft 筏Rail 栏杆、轨道Raked bow 前倾型船艏Range light 后桅灯、距离灯Ramp 跳板、滑道Rear door 后门Reduction gear box 减速箱Reeling drum (绞车)主卷筒Refrigerated room 冷藏室Registered port 注册港Reverse frame 内底横骨Rig 索具、钻井平台Right angle gunwale 直角舷边Roller 滚轮、滚柱Roller bearing 滚柱轴承Roller fairlead 滚轮导缆器Rope 缆绳Rotating chassis 回转底盘(克令吊)Rotating platform 回转平台Rotary screw propeller 回转式螺旋推进器RoRoship 滚装船Rubber 橡胶、橡皮Rubber packing 橡胶填料、橡皮条Rudder 舵Rudder bearing 舵承Rudder blade 舵叶Rudder control rod 操舵杆Rudder plate 舵板Rudder post 舵柱Rudder spindle 舵轴Rudder stock 舵杆Rudder trunk 舵杆围阱SSafety valve 安全阀Sand box 沙箱Sanitary tank 清洁用水柜Sail 帆Salver(tray)托盘Sampan 舢板Screen bulkhead 轻型舱壁Screw 螺旋桨、螺钉、螺杆Screw compressor 螺旋式制链器Screw propeller 螺旋桨Scupper 排水孔Scuttle 舷窗Seal ring 密封圈Seam 边接缝Search light 探照灯Semibalancedrudder 半平衡舵Semisubmersibledrilling platform 半潜式钻井平台Servo system 伺服系统Sewage 污水Shaft bossing 轴毂Shaft coupling 联轴节Shaft tunnel(passage)轴隧Sheave 滑车轮、槽轮Sheer 舷弧Sheer strake 舷顶列板Sheet 帆脚索Shell 船壳Shell plate 船壳外板Ship bottom plug 船底塞Shipyard 船厂Shoe piece 艉柱踵材Short beam 半梁Shroud 桅牵索Side 舷边Side frame 舷侧肋骨Side keelson 旁内龙骨Sideligth 舷灯Side plate 舷侧外板Side scuttle 舷窗Side stringer 甲板边板Signal bell 信号钟Silencer 消音器Single bottom 单底Single cylindrical roller chock 单柱式导缆钳Single plate rudder 平板舵Skylight 天窗Sleeve 衬套Slewing guy 摆动稳索Slewing hydraulic motor 回转液压马达Sloping bottom plate of topside tank 顶边舱斜底板Sloping top plate of bottom side tank 底边舱斜顶板Sofa 沙发Soft ladder 软梯Spade rudder 悬挂舵Spare parts 备件Speedometer 测速仪Sponson deck 舷伸甲板Spray gun 喷枪Stability 稳性Stairway 扶梯Stanchion 支柱Starboard 右舷Steel structure 钢结构Steering gear 舵机Steering wheel 方向盘、舵轮Stem 船艏Stem anchor 艏锚Stern 船艉Stern anchor 艉锚Stern ramp 艉跳板Stern shaft 尾轴Stern shaft tube 尾轴管Stern transon plate 艉封板Stiffener 加强板Storage battery 蓄电池Store box 备用柜Strengthen deck 强力甲板Stuffing 填料Summer loadline 夏季载重线Superstructure 上层建筑Swage plate 牙筋板Swash plate 止荡板、防波板Switch board 配电板Swivel link 转环(锚链)TTailstabilizeranchor 尾翼式锚Tank lid 货油舱盖Tank valve 货舱阀(油船)Tanker 油船TbarT 型材Tiller 舵柄Timber carrier 木材运输船Throttle valve 节流阀Thruster 侧推器Thruster bearing 推力轴承Tool box 工具箱Topping lift(line)千斤索Topping lift block 千斤滑车Topside tank 顶边舱Torsion 扭转Trailing edge 随边(螺旋桨叶)Transverse bulkhead 横舱壁Tug 拖轮Tunnel 轴隧Turnable blade 可转动浆叶Turning indicator 回转指示器Tweendeck cargo space 甲板间舱Tween screw 双桨UU sharp tankU 形水舱Universal fairlead 万向导缆器Upper deck 上甲板VVapor 蒸汽Vapor pipe 蒸汽管子Valve 阀Valve seat 阀座Variable pitch screw propeller 可变螺距螺旋桨Ventilator 通风筒Ventilator duct 通风管道Ventilator trunk 风路Vertical bow 垂直型船艏Vertical girder 竖桁Vertical shaft 垂直传动轴Viewfinder 反光镜View screen 旋转视窗WWaist band 腰带Warping drum 系缆滚筒Warping winch 系缆绞车Warship 战舰、军舰Wash basin 洗脸盆Water boiler 开水锅炉Water closet 抽水马桶Water filter 水过滤器Watertight 水密Watertight door 水密门Watertight floor 水密肋板Watertight stuffing 水密填料Weather deck 露天甲板Web 腹板Web beam 强横梁Web frame 强肋骨Wheel 车轮Whistle 汽笛Winch 绞车Windlass 锚机Windlass gipsy 起锚机卷筒Window certain 窗帘Windshield 挡风玻璃Wingkeel翅龙骨Wing deck 两翼甲板Wing tank 边舱Wire rope 钢索Wire rope fall 滑车钢丝绳Wireless antenna 无线电天线Wooden structure 木结构Worm 蜗杆Worm wheel 蜗轮YYacht 游艇Yard 船厂二、轮机词汇AAdapter 驱动器Adjustable wrench 活动扳手Adjusting ring 调整环Adjusting screw 调节螺钉Adjusting valve 调节阀Adjusting washer 调节垫圈Air adjust screw 空气调节螺钉Air admission valve 进气阀Air bottle 空气瓶Air charge cooler 进气冷却器Air charge valve 充气阀Air cleaner 空气滤清器Air compressor 空气压缩机Air cooler 空气冷却器Air cooler frame 空气冷却器壳体Air conditioner 空调Air distributor 空气分配器Air escape valve 排气阀Air filter 空气过滤器Air impeller 空气叶轮Air induction valve 进气阀Air inlet valve 进气阀Air motor 空气马达Air outlet valve 排气阀Air pipe 空气管Air piston 空气活塞Air pump 空气泵Air purifier 空气净化器Air reducing valve 空气减压阀Air refrigerated plant 空调制冷装置Air release valve 放气阀Air seal 气封Air spring 空气弹簧Air starting device 空气启动装置Air switch 空气开关Air tight door 气密门Alternator 交流发电机Aluminum anode 铝块保护Anchor and chain gear 锚链设备Anchor chain 锚链Anchor chain meter 锚链拉力器Angle lever 角杆Anticorrosive grease 抗蚀牛油Applicator for all purpose nozzle 多用途喷嘴接头Assembling nut 螺母套Attachment bolt 连接螺栓Automatic alarm 自动报警Automatic regulator 自动调节器Automatic stop valve 自动控制阀Automatic switch 自动开关Axle box 轴箱Axle bush 轴套Axle key 轴键Axle sleeve 轴套BBalance bush 平衡轴套Balance rudder 平衡舵Balance valve 平衡阀Balance wheel 飞轮Ball bearing 滚珠轴承Band 卡圈Banding screw buckle 带扣螺丝管夹Base 底座Bearing bush 轴承套Bearing cover 轴承盖Bearing shell 轴瓦Bearing stopper 轴承压盖Bearing,lower part 下轴承Bearing,upper part 上轴承Bleeder screw 泄放螺丝Blind flange 盲法兰Blind joint 封闭接头Blind nut 螺帽Block valve 截断阀Blowoffpipe 放气阀Body 本体Body packing 本体填料Boiler accessories 锅炉附件Boiler alarm 锅炉报警Boiler bedding 锅炉座Boiler blowoutpipeline 锅炉排污管Boiler feed pump 锅炉给水泵Boiler fittings 锅炉附件Boiler flat 锅炉平台Boiler furnace 锅炉炉膛Bolt 螺栓Bolt tension machine 螺栓拉力测量仪Bonnet 管帽Boss 轮毂Bottom cover 底盖Bottom flange 底部法兰Bracket 支架、三角板Brake 制动器、刹车Brass cap 铜管帽Brass cross 十字形铜接Brasselbow黄铜弯头Brass hexagon nipple 黄铜六角外螺丝Brass needle valve 黄铜针阀Brass reducing socket 黄铜异径套管Brass short nipple 黄铜短外螺丝Breaker bolt 安全螺栓Breather valve 通气阀Brine pipe 海水管Buffer 缓冲器Bursting plate 安全板Bush 布司(轴承)Bushing for roller guide 滚轮导套衬套Butterfly bolt 蝶形螺栓、元宝螺栓Butterfly nut 蝶形螺母Butterfly valve 蝶阀CCabin thermometer 室内温度器Cable 电缆Cable bushing 电缆衬套Cable cutter 电缆钳Cam 凸轮Cam clearance 凸轮间隙Cam driven 凸轮驱动Cam roller 凸轮滚柱Cam shaft 凸轮轴Cap head square neck bolt 盖头四角颈螺栓Carbon dioxide fire extinguisher 二氧化碳灭火器Carboncottonpacking 石棉填料Carborundum oil stone 油石Case 箱子Cast alloy 铸造合金Cast brass 铸造黄铜Cast bronze 铸造青铜Cast copper alloy 铸铜合金Cast ingot 铸锭Cast iron 铸铁Cast pipe 铸管Cast steel 铸钢Centering shaft 中心轴Chain drive and guide bar 链传动及导杆Chain link 链环Chain wheel 链轮传动Charge air pipe 增压空气管Check plate 挡板Checked plate 花铁板Check pin 止动销Check screw 固定螺丝Check valve 止回阀Check valve body 止回阀本体Check valve case 止回阀壳体Clamp 夹具、马脚Clamp screw 夹紧螺丝Clamp washer 夹具垫圈Clamp arm 夹臂Clamping piece 夹件Cleaning pipe 清洁管Cleaning valve 清洗阀Clutch body 离合器体Clutch coupling 离合器Clutch cover 离合器盖Clutch gear 离合器齿轮Clutch joint 离合器接头Clutch pin 离合器销Clutch rod 离合器拉杆Clutch shaft 离合器轴Coil 线圈Combined brine/air ejector 海水/空气混合喷射泵Combustible gas detector 可燃气体检测器Compensation valve 平衡阀Compression ring 压缩环Cone 圆锥体Conical bore 锥孔Conical valve 锥形阀Connection 接头Constant pitch propeller 定距螺旋桨Constant speed governor 定速调速器Control handle 控制手柄Control lever 操纵杆Cooling fin 散热片、冷却片Cooling fresh water pump 淡水冷却柜Cooling jacket 冷却水套Cooling oil pipe 冷却油管路Cooling system 冷却系统Cooling water connection 冷却水接头Copper pipe 铜管Cotter pin 开口销Coupling 联轴节、考必令Coupling flange 连接法兰Cover plate 盖板Crank pin bearing shell 曲轴销轴瓦Crank shaft gear 曲轴齿轮Crank web 曲轴臂Crankcase 曲轴箱Crankcase cover 曲轴箱盖Crankpin bearing cap 曲轴销轴承盖Crankshaft 曲轴Crankshaft distortion dial gauge 曲轴拐挡表Cross machine screw 十字槽螺钉Crosshead 十字头Crosshead bearing cap 十字头轴承盖Crosshead bearing shell 十字头轴瓦Crump band 卡环Cut ring 挡水环Cylinder 气缸Cylinder block 气缸体Cylinder body 气缸体Cylinder bore 气缸内径Cylinder cap 气缸盖Cylinder cover 气缸盖Cylinder head 气缸盖Cylinder head bolt 气缸盖螺栓Cylinder liner 气缸衬套Cylinder pin 气缸销Cylindering pin 圆柱形销DDamper 减震器Dead center 止点Deflector 定位螺钉Dehumidify 除湿Demister 去雾器Depth micrometer 深度测微器Dial gauge 测微器Diaphragm 隔膜Diaphragm valve 膜片阀Diesel oil 柴油Disc 圆盘Disc valve 圆盘阀Discharge valve 排出阀Distance bushing 定距套Distance ring 定距环Distributing cover 分配器壳体Distributing plate 分配板Distributor disc 配电盘Distributor plate 配电板Dosing ring 进料环Double direction thrust ball bearing 双向推力轴承Double open end wrench 双头开口扳手Drain tube 放残管Drain valve 防残阀Drive chain 传动链Drive gear 主动齿轮Drive gear box 主动齿轮箱Drive screw 驱动螺杆Driven gear 从动齿轮Driven shaft 从动轴Driving key 传动键Driving pin 压销Driving shaft 传动轴Driven wheel 传动轮Dust cap 防尘罩Dust catcher 吸尘器Dust cover 防尘罩Dust seal 防尘密封Dust remover 防尘器EEccentric 偏心轮Ejector nozzle 喷射嘴Ejector pipe 喷射管Elastic clutch 弹性离合器Elbow 弯头Elbow joint 弯头接头Elbow pipe 弯管Electric arc 电弧Electrical brush 电刷Electrical governor 电子式调速器Electrician screwdriver 电工用螺丝起子Element for filter 滤器滤心Emery cloth 纱布End cover 端盖End cap 端盖End housing 端盖End pin 尾销End plate 端板End ring 端环Engine base 机座Engine bed 机座Engine frame safety valve 机架安全阀Engine igniter 助燃剂Engine indicator 功率指示器Engine peak indicator 爆发压力示功器Exhaust boiler 废气锅炉Exhaust cam 排气凸轮Exhaust pipe 排气管Exhaust valve 排气阀Extension spring 受拉弹簧Eye bolt 吊环螺栓FFan 鼓风机Fan blower 通风机Fan house 风室Fan wheel 风轮Feed piping 给水管系Feed valve 给水阀Filter 过滤器Filter bowl 滤筒Filter drum 滤筒Filter net 滤网Fin 散热片Fire hose box 消防皮龙箱Fire hose nozzle 消防皮龙喷嘴First stage gear 一级齿轮Fitting flange 连接法兰Fitting plate 垫板Fixing bolt 固定螺钉Fixing pin 定位销Fixing plate 固定板Flange 法兰Flange nut 法兰螺母Flat key 平键Flexible hose 柔性管Float 浮子Float switch 浮子开关Float valve 浮阀Flow meter 流量计Flow switch 流量开关Fly wheel 飞轮Friction block 摩擦块Front cover 前盖Fuel oil injection pipe 高压油管Fuel oil injection pump 高压油泵Fulcrum 支点GGas inlet port 进气口Gas outlet 排气口Gasket 密封垫Gasoline(petrol)汽油Gauge 表Gear 齿轮Gear clutch 齿轮离合器Gear pump 齿轮泵Gear train 齿轮组Gland 压盖Gland box 填料函Gland cover 填料压盖Gland housing 填料函Gland packing 密封填料Gland seal 密封填料Governor 调速器Governor body 调速器本体Governor box 调速箱Governor driven gear 调速器从动齿轮Governor driving gear 调速器传动齿轮Governor handle 调速手柄Governor lever 调速杆Governor rod 调速杆Governor shaft 调速轴Grate 格栅Gravity disk 重力盘Grease gun 牛油枪Grease nipple 牛油咀Grease oil 牛油Gudgeon pin 十字头销Guide 导板Guide blade 导向叶片Guide block 导块Guide bushing 导套Guide cam 导向凸轮HHandle 手柄Handle stopper 止动杆Hand wheel 手轮Head cover 前盖Heat exchanger condenser 冷凝气热交换器Heat exchanger evaporator 蒸发器Heavy duty pump oiler 强力油泵Hexagon bushing 六角衬套Hexagon flange nut 六角法兰螺帽Hexagon socket head cap screw 内六角盖头螺钉Hinge 铰链Hinge joint 铰链接头Hinge pin 铰链销Holder ring 定位环Hose nipple 软管接头Hose line 软管Hydraulic governor 液压调速器Hydraulic jack 液压千斤顶Hydraulic pump 液压泵Hydraulic seal 水(压密)封Hydrometers for light oil 轻油比重计IIgnition 发火装置Impeller 叶轮Impeller casing 叶轮箱Impeller key 叶轮键Impeller nut 叶轮螺母Impeller pump 叶轮泵Impeller shaft 叶轮轴Indicator 指示器Indicator cam 指示器凸轮Indicator valve 示功器Inducer 叶轮Inducer key 导风轮键Inlet elbow 进口弯头Inlet pipe 进口管Inlet valve 进口阀Inner case 内套Inner link 内链环Inner ring 内环Input shaft 主动轴Inspection glass 观察镜Insulating joint 绝缘接头Insulating disc 绝缘板Insulation cover 绝缘盖板Intermediate bearing 中间轴承Intermediate shaft cover 中间轴承盖Iron block 铁块JJacket cooling water 气缸套冷却水Jacket water inlet 气缸套冷却水进口Joint 接头Joint nut 接头螺母Joint piece 连接件Joint seat 连接座Junction block 连接块Junction box 接线盒Junction bolt 连接螺栓Junction pipe 连接管Junction plate 连接板KKerosene 煤油Key 键Key slot 键槽Knob 旋钮Knock 止动销LL.O.(lubricate oil)润滑油L.O.nozzle 滑油喷嘴L.O.pump body 滑油泵本体L.O.pump cover 滑油泵端盖L.O.pump driven gear 滑油泵从动齿轮L.O.pump driving gear 滑油泵主动齿轮L.O.cut plate 挡油板Lamella for scraper ring 刮油环薄片Lever 杆Lid 盖Lifeboat compass 救生艇磁罗经Lifting bolt 吊环Lifting eye 吊环Lifting stud 支撑轴Liner 衬套Liner for spindle guide 阀杆导套衬套Link 连接环Link joint 活动连接Link pin 连杆销Link rod 连杆Lock 锁Lock pin 固定销Lock washer 锁紧垫圈Locking claw 止动爪Locking ring 锁紧环Locking wire 锁紧丝Locknut 防松螺丝Lub oil pump 润滑油泵Lubrication pipe 润滑油管Lubricator 主油器MMachine tool 机床Machinist file 三角锉刀Main bearing 主轴承Main bearing shell 主轴瓦Main bearing stud 主轴承双头螺栓Main driving gear 主传动齿轮Main spring 主弹簧Male cross 外螺十字接头Male elbow 外螺纹弯头Manhole cover 人孔盖Manifold 总管Manometer 压力计Marine bronze 船用青铜Marine cast iron 船用铸铁Marine cast steel 船用铸钢Marine forged steel 船用锻钢Measuring tape 卷尺Mechanical joint 机械连接Mechanical seal 机械密封Metal lining 金属衬板PPipe seal 管封Piston 活塞Piston rod 活塞杆Piston skirt 活塞裙Pitch 沥青Plane washer 平垫圈Plastic hammer 塑胶锤Plate clutch 圆盘离合器Plug 旋塞Plunger 柱塞Pneumatic sump pump 气动式潜水泵Pointed cone 尖锥Pointed drill 尖钻Pointed screw 尖头螺钉Portable oxygen indicator 可携式测氧仪Portable ejector 手提喷射泵Power wrench 省力扳手Pressing bolt 压紧螺丝Pressing ring 压紧环Pressure gauge 压力计Pressure valve 压力阀Pull rod 拉杆Pump impeller 叶轮泵Push button 按钮Push rod 推杆QQuick coupling,complete 活接头总成RRack rail 齿条Wheel 齿轮Reducing gear 减速齿轮Regulating nut 调整螺母Regulating ring 调整环Relief plug 释放塞Relief ring 保险环Relief valve 安全阀Resilient arm 强力臂Return main 回流总管Return pipe 回流管Return valve 回流阀Reversing shaft 逆转轴Reversing valve 换向阀Ring 环Ring gasket 衬圈Ring valve 环形阀Rod 杆Roller 滚轮Rotary pump 回转泵Rotary valve 回转阀Rotor side ring 转子侧环Round nut 圆头螺母Rubber cord 橡胶条Rubber hammer 橡胶锤Rubber protective steeve 橡胶保护套Rubber seal 橡胶密封Rust preventive 防锈圈SSafety bolt 贯穿螺栓Safety cap 安全帽Safety cock 安全旋塞Safety collar 安全环Safety valve 安全阀Scavenge air recciver 扫气箱Scraper ring 刮油环Screw 螺钉Screw die 板牙Screw nut 螺母Seal noise 密封Seal washer 密封垫圈Seat 座Seat ring 环座Seawater pipe from condenser 冷凝器海水管Second stage gear 二级齿轮Separator 分离器Servo brake 伺服制动器Servo clutch 伺服离合器Servo drive 伺服传动Servo lever 伺服杆Servo oil cylinder 伺服油缸Servo pump 伺服泵Set hammer 扁锤Set nut 固定销Set ring 固定环Shaft 轴ShaftpinforShaftpinfor roller 滚轮轴销Shaft alley 轴隧Shaft bearing 轴承Shim 垫片Shock absorber 减震器Shrink ring 扣环Shutoffvalve 截止阀Sight glass 观察镜Silencer ring 消音环Sleeve 套管Sleeve coupling 轴套联轴节Sleeve nut 套管螺母Slide 滑块Slide bar 滑杆Slide valve 滑阀Slider door 滑动门Slider hook 滑钩Sludge burner 焚烧炉Socket 套管Special nut 专用螺母Special tool 专用工具Special plug 专用旋塞Speed control nut 调速螺母Spherical valve 球阀Split pin 开口销Spindle 阀杆Spindle guide 阀杆导套Spray nozzle 喷嘴Spray pipe 喷管Spring 弹簧Spring pin 弹簧销Spring valve 弹簧阀Stainless steel 不锈钢Stainless steel head plug 不锈钢方头止栓Start valve 启动阀Starting air bottle 启动空气瓶Starting air compressor 启动空气压缩机Starting air pipe 启动空气管Starting air relief valve 启动空气安全阀Starting air stop valve 启动空气截止阀Starting air timing valve 启动空气分配阀Starting air valve 启动空气阀Staror 定子Stay bolt 贯穿螺栓Steam injector 蒸汽喷射泵Steel compasses 钢质圆规Steering alarm indicator 舵机报警指示器Steering chain 转舵链。

【知识】船舶轮机英语:基础词汇

【知识】船舶轮机英语:基础词汇

【知识】船舶轮机英语:基础词汇第六部分:基础词汇Ⅰ.技术术语 Technical Terms1、pump 泵①Supply pump供给泵②transfer pump 输送泵③circulating pump 循环泵④bilge pump 舱底水泵⑤ballast pump 压载水泵1、tank①drain tank 泄放柜②service tank 日用柜③settling tank沉淀柜④storage tank 储存柜⑤circulating tank 循环柜⑥used oil tank 废油柜⑦buffer tank 缓冲柜⑧overflow tank 溢流柜⑨Collecting tank 收集柜⑩expansion water tank 膨胀水箱2、water①sea water (S.W.) 海水②fresh water (F.W.) 淡水③operating water 工作水④sanitary water 卫生水⑤washing water 冲洗水⑥refilling water 再注水⑦feed water 给水⑧condensate water 冷凝水⑨bilge water 舱底水⑩sewage 污水2、oil①fuel oil (F.O.) 燃油②lubricating oil (L.O.) 滑油③engine oil 机油④cylinder oi l 气缸油⑤diesel oil (D.O.) 柴油⑥turbine oil 透平油⑦cool oil 冷却油⑧seal oil 密封油3、temperature (temp) 温度4、flow 流量5、pressure(press)压力6、power 功率10、level 液位11、vibration 振动12、normal/abnormal 正常/异常13、main/auxiliary (aux.) 主要/辅助的14、inlet/exhaust 进气/排气15、fire alarm 火警16、fail/failure 故障17、overload 过载18、no-voltage 失电19、leak/leakage 泄漏20、wrong-way 错向21、insulation(insul) 绝缘22、oil mist 油雾23、viscosity 粘度24、density 浓度25、salinity 盐度26、oil content 油含量27、pressure difference 压差28、switch 开关29、flame 火焰30、automatic(auto)自动的31、emergency 应急的32、standby 备用的33、screw 螺丝34、nut 螺母35、stud 螺柱36、meter 仪表37、thermometer温度计38、level gauge 液位计38、pressure gauge 压力表39、length 长度40、breadth 宽度41、height 高度42、meter 米43、centimeter 厘米44、millimeter毫米45、decimillimetre 丝米46、micrometer微米46、hundredth of one millimeter 丝47、de(rust)生锈(除绣)48、spare parts 备件49、spanner 扳手50、ahead/astern 正车/倒车51、screwdriver 螺丝刀(minus / plus)52、sludge 油渣53、electrician’s knife 电工刀54、decrustation pliers 剥线钳Ⅱ.(主机主要部件) Main Parts for M/E1、engine frame 机架2、cylinder 气缸3、piston 活塞4、crosshead 十字头5、bedplate 机座6、crankshaft 曲轴7、cylinder cover/head 气缸盖8、connecting rod 连杆9、turbocharger 增压器10、driving chain 传动链11、air cooler 空气冷却器12、scanvage box 扫气箱13、oil sprayer 喷油器14、oil nozzle 喷油嘴15、exhaust valve 排气阀16、sealing ring密封环17、cylinder liner 气缸套18、piston rod 活塞杆Ⅲ.机舱布置图 Engine room arrangement1、main engine /M.E. 主机2、intermediate shaft 中间轴3、bearing 轴承4、propeller shaft 螺旋桨轴5、stern tube艉管6、aft seal head tank 后密封油箱7、FWD seal head tank前密封油箱8、stern tube L.O. drain tank 艉管滑油泄放柜9、chemical cleaning tank 化学清洗柜10、L.O. drain tank11、sludge oil trap 油渣收集柜12、rust preventer tank 防锈剂柜13、 oily water separator油水分离器14、Low sea chest 低位海水门15、L.O. transfer pump16、bilge pump 舱底泵17、M/E lub oil pump18、M/E S.W. cooling pump 主机海水泵19、sludge pump 油渣泵20、ejector pump for F.W.G 造水装置工作水泵21、stern tube L.O. pump 艉轴管滑油泵22、H.F.O. Transfer pump 燃油输送泵23、ballast pump 压载泵24、bilge & G.S. pump 舱底总用泵25、Fire & G.S. pump 消防总用泵26、Provision Ref. Unit S.W. pump伙食冷藏海水泵27、aux. S.W. Cooling pump 辅海水泵28、L.O. purify cleaning tray 滑油分油机洗池29、L.O. purify. Operating water tank 滑油分油机工作水箱30、L.O. purify. Heater滑油分油机加热器31、diesel generator 柴油发电机组32、D/G F.W. Cooler 柴油发电机淡水冷却器33、boiler feed water pump 锅炉给水泵34、cascade tank 热井35、aux.condenser 大气冷凝器36、inspection tank 凝水检查柜37、filter 过滤器38、distilling plant 造水装置39、control air vessel 控制空气瓶40、control air dryer控制空气干燥器41、air compressor 空压机42、main air vessel 主空气瓶43、M/E F.O. heater 主机燃油加热器44、purif room exh fan分油机室抽风机45、sludge tank 油渣柜46、drinking water hydrophone tank 饮水压力柜47、calorifier 热水柜48、drinking water sterilizer 饮水消毒器49、emergency air compressor50、stern tube gravity oil tank艉管重力油柜51、antifouling system power unit防污系统电源箱52、ECR. Unit cooler 集控室空冷机53、overhead crane 机舱行车54、boiler feed water test kit 炉水试验台55、cylinder oil measuring tank气缸计量柜56、sink 洗池57、gas welder 气焊机58、E.L. welder 电焊机59、universal machine 组合机床60、driller 立式钻床61、bench 钳桌台62、vice台虎钳63、grinder 砂轮机64、cupboard 橱65、sewage treatment unit 生活污水处理装置66、composite boiler 燃油/废气组合锅炉67、forced draft fan 锅炉强力风机68、incinerator焚烧炉69、waste oil service tank 废油日用柜70、supply ventilating fans 送风机71、spark arrester消音器Ⅳ.Others1、shipyard 船厂2、shipbuilding 造船3、berth/slipway 船台4、marine diesel engine 船用柴油机5、bulk-cargo carrier 散装货船6、container ship 集装箱船7、oil tanker 油船8、tonnage 吨位9、merchant ship 民用船10、military ship (warship) 军用船11、drawing 图纸12、hull 船外壳13、bow/stern 船艏/船尾14、port/starboard 左舷/右舷15、deadweight 载重量16、displacement 排水量17、freeboard 干舷18、deck 甲板19、keel 龙骨20、anchor 锚21、rudder 舵22、bottom 底23、supersrtucture 上层建筑24、side25、weld 焊26、painting 油漆27、assemble 装配28、launching29、sea trial 试航30、delivery 交船31、tightness test 密性试验32、after service 售后服务33、approval 认可34、blue collar worker 蓝领35、maker36、rules and regulations 规则、规范37、chief engineer 轮机长38、chief officer大副39、clerk 事务员40、foreigner41、fore peak 艏尖舱42、aft peak 尾尖舱43、frame 肋骨44、cabin 舱室45、wheel house 驾驶室46、shaft tunnel 轴隧47、beam横梁48、manhole 人孔49、bulbous bow球鼻艏50、sea chest 海水门51、bulkhead 隔舱壁52、dry cargo hold 干货舱53、provision store 食品库54、passageway 走廊、通道55、refrigerating chamber 冷藏室Ⅴ甲板机械 Deck Machinery1、deck 甲板2、anchor chain(cable)锚链3、chain locker 锚链舱4、windlass 起锚机5、mooring hole 导缆孔6、bollard 带缆桩7、cargo winch 起货绞车8、hand rail 栏杆9、hawse pipe 锚链筒10、hatchcover 舱口盖11、hatch coaming舱口围板12、control cabin操纵室13、derrick 吊杆14、cargo hook 吊货钩15、mooring winches 系泊绞车16、wire cable 钢索17、vertical ladder 直梯18、wire steel 钢丝卷筒19、side scuttle舷窗20、rudder stock 舵杆21、rudder shaft 舵轴22、flag staff 旗杆23、ventilator 通风筒Ⅵ.管系 for piping1、Exhaust air system 排气系统Exhaust pipe for M.E(Generators / boiler / emergency generators)主机 / 发电机 / 锅炉 / 应急发电机2、Cooling Water System 冷却水系统①cooling fresh water (CFW) 淡水冷却水②cooling sea water (CSW) 海水冷却水3、fuel oil system 燃油系统①light diesel oil②heavy diesel oil (HDO)③fuel oil purifying 燃油净化④oil sludge 废油(污油)⑤fuel oil transferring 燃油输送4、Lubricating oil system①L.O for M.E(generator / stern tube)②Lub. oil transferring5、Compressed air system①high / low pressure air②starting air 起动空气③control air④remote control air 遥控空气⑤miscellanous air 杂用空气6、Ship systems①the bilge system舱底水②the ballast system 压载水③the water supply system 供水④the steam system 蒸汽⑤the drainage system 排水⑥the fire-fighting system 消防⑦the air measuring and filling system 空气测量注入⑧the level system 液位7、filter / filter gauze (screen)8、drainage valve sets9、pressure gauge 压力表9、vacuum真空表10、thermometer 温度计11、steel tube 钢管12、copper tube 铜管13、observation glass 观察镜14、funnel 漏斗15、hose 软管16、induction port 吸口17、bracker 支架18、shim (washer) 垫片19、flange 法兰20、connection 接口21、stainless steel pipe 不锈钢管22、threaded connection 螺纹接头23、sleeve pipe 套管24、flowmeter 流量计25、radiator 散热器26、pipe wrench 管子钳27、spanner 扳手28、pipe cutter 管子割刀29、scraper 刮刀30、vice 老虎钳31、screwdriver 螺丝刀32、torch 手电筒Ⅶ主要阀件铭牌 Main valve list1、slush valve 截止阀2、non-return valve 止回阀3、through-way valve 直通阀4、butterfly valve 蝶阀5、sluice valve 闸阀6、remote-control butterfly valve 遥控蝶阀7、quick closing valve 速关阀8、self-closing valve 自闭阀9、reducer valve 减压阀10、ball valve 球阀11、copper valve 铜阀12、steel valve 钢阀13、cast iron valve 铸铁阀14、stainless steel valve 不锈钢阀15、safety valve 安全阀16、temperature adjusting valve 温度调节阀17、thermostatic valve 恒温阀18、induction valve 进气阀19、exhaust valve排气阀20、drain valve 排泄阀21、fire valve 消防阀22、three-way valve 三通阀23、valve material①cast iron 铸铁②cast steel铸钢③stainless steel④bronze 青铜⑤brass黄铜⑥copper紫铜⑦nodular cast iron球墨铸铁Ⅷ.电力设备 electrical equipment1.emergency (diesel / tacho- / shaft) generator应急(柴油/ 测速/ 轴带)发电机2.servo (governor) motor 伺服(调速)马达3.ignition (current / voltage) transformer点火变压器(电流/电压互换器)4.converter 变流器5.frequency changer 变频器6.charger 充电器7.rectifier 整流器8.uninterrupted power source (UPS)不间断电源装置9.battery or storage battery蓄电池或蓄电池组10.main (emergency / power section) switchboard 主(应急/电力区)配电板11.generator (feeder) panel 发电机(馈电)屏12.charging & discharging panel 充放电板13.(radio / low voltage / internal communication) power distribution board无线电(低压 / 船内通信 / 电力)分电箱14.power unit for cathodic protection阴极保护电源箱15.test panel 电工试验板16.shore connection box 岸电箱17.junction box (with fuse) 接线箱(带熔断器)18.control console (panel) 控制台,集控台19.main engine control stand主机控制台20.motor starter 电动机起动器21.control box (panel) 控制箱(板)22.main engine safety (air conditioning) control box主机安全系统(空调)控制箱23.control box for singal light信号灯控制箱24.steering gear source box 舵机电源箱25.contactor 接触器26.relay 继电器27.control (pressure / change over) switch 控制(压力 / 转换)开关28.magnetic valve 电磁阀29.resistor 电阻器30.push button 按钮31.temperature transducer 温度变换器32.oil mist detector 油雾探测器33.fuse 熔断器34.Ammeter 电流表35.voltmeter 压力表36.power meter 功率表37.power factor meter 功率因数表38.watt-hour meter 电度表39.frequency meter 频率表40.flow meter 流量表41.speed indicator 转速表42.ohm meter 欧姆表43.welder 电焊机the 车床45.drilling machine 钻床46.planning machine 刨床47.grinding machine 砂轮机48.electric heater 电热器49.electric refrigerator 电冰箱50.electric fan 电风扇51.air conditioner 空调52.washing machine 洗衣机53.fresh water sterilizer 引水消毒器54.stator 定子55.rotor 转子56.neutral wire 零线(中性线)57.winding 绕组58.coil 线圈Ⅸ.illumination equipment 照明设备1.port (starboard) light 左右舷灯2.mast 桅灯(stern艉灯 / anchor锚灯 / steering操舵灯 / signal 信号灯 / flashing 闪光灯/ towing 拖船灯/ daylight signal 白昼信号灯/ pendant 舱顶灯/ fluorescent pendant 荧光舱顶灯/ ceiling 蓬顶灯/passage corner 走道角灯/ desk 台灯/ wall 壁灯/ berth 床头灯/ r oom’s nameplate 舱室铭牌灯/ chart table 海图灯/ flameproof 防爆灯/ flood 泛光灯(强光灯)/ search 聚光灯(探照灯)) light3.switch开关4.plug插头5.socket 插座6.socket box 插座箱Ⅹ.Navigation equipment 导航设备1.gyrocompass 电罗径2.magnetic compass 磁罗径3.feedback unit 反馈装置4.echo-sounder 回声测深仪5.log 计程仪6.master (slave) clock 母(子)钟7.radar 雷达8.radio direction finder 无线电测向仪9.Loran (radio navigation / satellite navigation) receiver劳兰(无线电导航 / 卫星导航)接收机10.VHF radio telephone transceiver 甚高频电话收发信机11.facsimile 传真机12.television set 电视机13.video camera 电视摄像机oxygen 氧气acetylene 乙炔nitrogen 氮气inter gas 惰性气体epoxy 环氧的resin 树脂chock楔子垫木soapy water 肥皂水anemometer 风速计manometer 压力(压强)表,气压表straight edge 直尺feeler gauge 塞尺steel scale 钢尺dial gauge 千分表micrometer 外径千分尺vernier caliper 游标卡尺spanner 扳手wrench 扳手screw driver 螺丝刀hammer 锤子clinometer 测斜仪chain block 手拉葫芦mandatory 命令、强制的Chlorinator 氯化器syphon=siphon 弯管,存水管,虹吸管blind 盲板booklet of piping procedure 工序,过程,步骤gymnasium 健身房galley 船上厨房motorcycle safety helmet 安全帽life belt 安全带glove 手套respirator 口罩overall 工作服 uniformelectric torch 手电筒 flashligheyeglass 眼镜elevator 电梯plank 厚木板stage 大舞台expressions 公式 formula(复数formulae)plus 加,正minus 减,负multiply 乘divide by 用…除equal to 等于sb entrust sb with sth 委托某人reply to 答复promise 许诺explanation 解释说明answer to 答案typist 打字员triangle 三角形quadrangle 四边形四角形pentagon 五角形inflator 打气筒tyre 轮胎wheel 车轮off duty 下班on duty 上班overtime 加班Slipway、shipway船台1.Lighting alignment for shafting & rudder system 轴舵系照光对中2.Stern tube boring 艉轴管镗孔3.Stern tube bush 艉轴衬套4.Stern boss艉轴壳5.forced fitting inspection压入配合检验6.oil jack(千斤顶)油泵7.(propeller shaft & stern tube bush)radial clearance (艉轴和艉管衬套)径向间隙8.axial clearance 轴向间隙9.Stern tube seals sealing 艉轴密封10. propeller installation force fitting压配11.pull-up length压进距离12.pull-up force 推进力13.oilpressure for boss 扩涨油压14.Zero point 零点15. Shrinkage 过盈量16.cleanness光洁度17.taper圆锥,斜度18. superposition 重合19. intersect 相交20.perpendicularity 垂直度21.vertical垂直的22.horizontal 水平的23. nut of stern shaft艉轴螺栓24.rudder 舵25.rudder blade 舵叶26.rudder stock 舵杆27.rudder pintle 舵销28.rudder tiller 舵柄29.rudder bush 舵承30.rudder horn 挂舵臂31. securing key 定位销,定位键32.protecting cover 保护帽33.grease牛油34.rudder angle 舵角35.full angle 满舵36. rudder blade’s stopper 防跳块37.temperature sensor 温度传感器38. inlet outlet 进出39. tolerance 公差,允许量40.wear down gauge 磨损规41.stern tube main chamber 大腔42.high pressure chamber 高压腔43.low pressure chamber 低压腔Engine Room 机舱1.Cleaning check:Storage oil tank of steering gear 舵机储存油箱(方形)Expansion oil tank of mooring winch 绞机膨胀油箱(圆形)Storage oil tank of mooring winch 绞机储存油箱Storage oil tank of windlass 锚机储存油箱(方形)Expansion oil tank of windlass 锚机膨胀油箱(圆形)Hydraulic oil tank of hatch cover 舱口盖液压油箱2.flushing of winch piping 绞机管路投油1.D/G pouring epoxy chock 发电机浇环氧2.holding down bolt 地脚螺栓3. deflection of crankshaft 曲轴甩档4.piston 活塞5.cylinder 气缸6. turbocharger 涡轮增压器1.Force measurement of M/E stay bolts 紧固螺栓2.piston rod and connection rod bolts 活塞杆和连杆螺栓3.bolts in drive end of crank 曲轴大端螺栓4.piston—piston rod—crosshead—connection rod—crank—crankshaft活塞活塞杆十字头连杆曲柄曲轴5.cam 凸轮6.camshaft 凸轮轴7.M/E chain cable 主机链条8.flooding test of M/E return oil pipes 压水试验9.propeller cap—propeller—stern tube seals—stern tube bush—stern shaft—intermediate shaft导流帽螺旋桨艉密封艉管衬套艉轴中间轴—intermediate bearing—flywheel (thrust shaft)中间轴承飞轮推力轴10.coupling reamer holes 联轴节铰制孔11.turning gear 盘车机12. spring 弹簧1.main air compressor 主空压机2.alignment of coupling flange 联轴节对中3.gap 裂面4.sag 位移1.steering gear 舵机2. ram roller bearing 舵机活塞杆轴承3. neck bush & cylinder 舵机活塞颈衬套和活塞缸体4. dimension measurement 尺寸测量1.fore draft valve艏吃水阀2.speed log 计程仪3.echo sounder 测深仪Quay、shipside、wharf、dock码头感谢阅读,这里是龙de船人获取更多资讯,请关注后输入关键字搜索投稿、建议、沟通:*****************。

船舶航海英语词汇

船舶航海英语词汇

..船舶航海英语词汇 Ranks of ship ’s crew(船员职务) crew 船员 captain (master ) 船长 chief officer 大副 or chief mate (first mate ) second chief 二副 or second mate third officer 三副 or third mate assistant officer 驾助 radio officer (radio 报务员operator, wireless operator ) purser (chief purser) 管事,事物长 clerk 事务员 boatswain or bosun 水手长 cassab 副水手长 quartermaster 舵工 coxswain 舵工,艇长 able seaman 全能水手,一水 a.b.(able bodied seaman)全能水手 e. D.h. , d.h.u. 全能水手 o.s.(ordinary seaman)普通水手,二水 seaman, mariner 普通水手,海员 deck boy 甲板员 engineer 轮机员 chief engineer 轮机长,大车,老轨 second engineer 大管轮,二车,二轨 third engineer 二管轮,三车,三轨 fourth engineer 三管轮,四车,四轨 assistant engineer 轮助 mechanic 机工 fireman 生火 cleaner or wiper 清洁工 chief steward 大管事 (or catering officer) second steward 二管事 chief cook 大厨 second cook 二厨 supernumerary 额外人员 ship ’scomplement 船上的定员 deck serang 水手长 deck tindal 副水手长 seacunny 舵工 Names of marine organizations and their( 船务机关名称及工作人员) harbour administration bureau (or harbour bureau)港务局 the joint inspection party-inward and outward 进口联合检查组 harbour supervision office 港务监督 the customs 海关 frontier inspection station 边防检查站 quarantine office (s0ervice) 卫生检疫所 animal and plant quarantine service 动植物检疫所 china commodity inspection and testing bureau(ccitb) 中国商品检验局 china marine bunker supply corporation 中国船舶燃料供应公司 china national chartering corporation(zhongzu) 租船公司 china ocean shipping agency 中国外轮代理公司 china ocean shipping company (cosco) 中国远洋运输公司 china ocean shipping company chartering department(coschard) 中国远洋轮船公司租船部 (“中远租”) chian ocean shipping tally company 中国外轮理货公司 china ocean shipping supply corporation(supco.)中国外轮供应公司 the ~ office of the register of shipping of the people ’s republic of china 中华人民共和国船舶检验局~办事处 joint inspection party 联检小组 customs officer 海关官员 harbour officer 港务监督员 frontier defence officer (inspector ,guard) 边防检查组 Quarantine officer(dotor) 卫生检疫员 customs boarding office 登轮官员 customs searching party 海关检查组 docker 码头工人(广义) longshoreman 码头工人(在岸上装卸) stevedore 码头工人(在船上装卸) foreman 装卸队长 pilot 引水员 cargo surveyor 商品检验员 marine or ship surveyor 验船师 chief tallyman 理货员 waterman 加水工人 agent 代理 Marine loading and discharging gear and harbour facilities (海运装卸机械工具和港口设施) barge 驳船 beacon 航标灯 belt conveyor 皮带运输机 board palnk 木版 bridge crane 桥吊,装卸桥 bunkering tanker 供燃料船 buoy 浮筒,浮标 can hook ,barrel sling 吊桶钩 canvas 帆布 canvas sling 吊货帆布袋 cargo tray 吊货盘 cargo runner 吊货钢丝绳 chafing plate 防擦板 chafing mat 防擦席 chain sling 链条吊索 crane 吊车 cold storage 冷藏仓库 conveyor belt 传送带 crowbar 撬杠 customs launch 海关关艇 dolphin 系缆桩 dunnage 垫仓物料 electric crane 电吊 elevator 升降机 ferry boat 轮渡船 fire boat 消防船 floating crane 浮吊 footboard 踏板 fork - lift 铲车,叉车 funnel 漏斗 gangboard 跳板 gantry crane 龙门吊 garbage(sludge,sewage) boat 垃圾船 grab 抓斗 grain elevator 吸粮机 hammer 铁锤 handcart 手推车 harbour light 港口灯标 iron nail 铁钉 landing pier 登岸码头 lifting maget 西铁吊具 lighter 驳船 light house 灯塔 light ship 灯船 manila rope 白棕绳 mat 席子 mobile crane 流动吊车 mooring anchorage 系泊锚地 mooring buoy 系泊浮筒 motor launch 小汽艇 nylon rope 尼龙绳 oil hose 输油软管 open yard 露天货场 personnelboat 交通艇 pilot boat 引水船 plate hook 钢板吊钩 pontoon 浮码头 pontoon bridge 浮桥 quarantine anchorage 检疫锚地 quarantine vessel 检疫船 refrigerator car 冷藏车 rope sling 绳吊索 saw 锯 semi-portal crane 半门吊 shifting board 防动板 signal tower 信号台 steam launch 小汽艇 steel wire 钢丝绳 tower crane 塔吊 tractor 牵引车 traffic boat 交通艇 tug boat(motor tug) 拖轮 warehouse 仓库 water boat 供水船 watr lever indicator 水深标尺 wire cargo net 钢丝网络 wire sling 钢丝吊索 various kind of vessels (各种船舶) air cushion craft 气垫船 bage-carrier 载驳货船 bulb-bowed ship 球鼻首船 bulk-carrier 散货船 cargo liner 定期货船 collier 散货船 crew boat (船员)联络船 diesel boat 柴油机船 dry cargo ship 干货船 dumb lighter 驳船(没有机器的) freighter 货船 oil barge 油驳 ore carrier (ore ship ) 矿砂船..reefer (refrigerator ship ) 冷冻船 salvage vessel 救助船 grain carrier 运量船 ice-breaker 破冰船 light ship 未载货的货船 lumber carrier (timber carrier ) 运木船 meat ship 肉类船 moto ship 内燃机船 ocean-going vessel 远洋船 sister ship 姐妹船 steam ship 蒸汽机船 stor carrier 补给船 tanker (oil tanker ) 油驳 trawler 拖网渔船 Major marine papers and certificates (主要船务单据及证书) (1)papers 单据 application for bunkers 加(燃油)申请书 application for tallyman 理货申请书 bill of lading 提单 booking note 订舱单 boat note 订载单 cargo receipt 交货收据 cargo tally sheet 理货记数单 copy 副本 damaged cargo report 货物残损报告书 declaration 申报单 delivery order 交货单 dock receipt 码头收据 gang record 工班报单 hatch(cargo)list 分舱单 inward manifest 进口舱单 license 许可证 mate ’s receipt 收货单 notice of arrival 到货通知书 motice of claim 索赔通知 notice of readiness 准备就绪通知书 on-spot record 现场记录 original 正本 outward manifest 出口舱单 parcel receipt 小包收据 sailing orders 开航通知 shipper ’s export declaration 货物出口申请书 shipping list 装货通知书 shipping permit 准运单 short/overlanded cargo list 货物溢短单 short/overlanded cargo report 货物溢短报告单 tally daily report 理货日报告 tally sheet 理货单 tally shift report 理货工班报告 2 )certificates ( 证书,证件) certificate of freeboard 干舷证书 certificate of health 无疫证书 certificate of origin 产地证书 ceitificate of port registry 船籍港证书 certicficate of survey 船舶检验证 classification certificate 船级证书 deratting certificate 除鼠证书 deratting exemption certificate 免予除鼠证书 inspection certificate 验讫单 international loading certificate 国际载重线证书 maritime declaration of health 航海健康申明书 navigation certificate seaworthiness certificate 适行证书 outward clearance certificate 出国证书 panama canal tonnage certificate 巴拿马运河吨位证书 passport 护照 safety radio telegraphy certificate 无线电报安全证书 ship ’s safety certificate 船舶安全证书 sues canal special tonnage certificate 苏伊士运河专用吨位证书 tonnage certificate 吨位证书 tonnage dues certificate 吨税证书 wireless inspection certificate 无线电安全证书 The structure of a ship(船舶结构) accomodation 房间 accomodation ladder 舷梯 aerial(antenna) 天线 aft part(after part) 船尾部 after-peak 后尖舱 air siren 汽笛 aldis lamp 闪光信号灯 alleyway 走道 anchor 锚 anchor chain 锚链 auxiliary machinery 辅机 bilge 船底沟 binnacle 罗盘支架 bitts(bollards) 系缆柱 block 滑轮 boom 吊杆 bow 船头 port bow 左舷船头 starboard bow 右舷船头 break 夹板台阶 bridge 船桥,驾驶台 brow (从船上到岸上的)舷梯 bulwarks 舷墙 bunker 燃料舱 cabin 船舱 pilot ’s cabin 引水员房间 cable 锚链 capstan 绞盘 cargo hold 货舱 catwalk 狭窄的舷梯 awning 帆布蓬 baggage room 行李房 barometer 气压表 basic line 吨位标志线 balk(blulk) , beam 船梁 hatch beam 舱盖横梁 port beam 左舷 starboard beam 右舷 chain locker 锚链舱 chronometer 经纬仪 coamings 舱口栏板 compass 罗盘course recorder 航向记录仪crane 起重机 davit 挂艇架 deck 甲板boat deck 救生艇甲板 lower deck 下甲板 lower tween deck 二层柜 main deck 正甲板 poop deck 船尾上面的甲板promenade deck 保护甲板之上甲板 shelter deck 遮蔽甲板 tonnage deck 量吨甲板 tween(between)deck 二层柜 upper deck 上甲板 upper tween deck 三层柜 deck house 甲板室 derrick 吊杆diesel engine 柴油机double bottom 双层底 draught marks(draft marks) 吃水标志 dynamo(generat 发电机 echo sounder 测深仪 engine roon 机舱 engin roon department 机舱部 escape trunk 救生道 fan room 打风间falg-staff 旗杆 forecastle 船首楼forecastle head 船头甲板 foremast 头柜 forepart 船头部 forepeak 前尖舱freeboard deckling 干舷甲板线 gangway 舷梯 glass (口语)气压表guy 稳索 gyro compass(gyro) 电罗经 halliard ,halyard 旗帜之升降索 hatch 舱口 hatch bord 舱盖板hatch coaming 舱口栏板 hatch cover 舱口盖 hawse hole 锚链孔 helm 舵轮;舵柄 hawser 船缆;锚链hull 舱壳jack ladder(jacob ’s ladder)软梯,绳梯 jackstaff 船头小旗杆 jigger mast 尾 jumbo(derrick 重吊(杆) keel 龙骨 life belt 救生带 life bort 救生艇 life buoy 救生圈 life jacket 救生衣 life raft 救生筏life-saving apparatus 救生设备 load ling 载重线,装载水线 mainmast man-rope 绳索mizzen mast monkey island 瞭望台 pilot ladder 领港梯子..piston 活塞 plimsol ’s mark 载重线标志 poop 船尾楼 port 港口,舱口,左舷 port -hole 舷舱,舱口 propeller 螺旋桨 pulley 滑轮 pump 水泵 purchase 绳索,滑轮 quarter 船舷的后部 port quarter 左舷后部 starboard quar 右舷后部 radar 雷达 radio 无线电 radio direction finder 无线电测向器 radio room 无线电室 radio transmitter 无线电发射机 rast 救生筏 rail,railings 扶手,栏杆 rat-guard 缆绳上的防鼠隔 ratlines 绳梯横索 refrigerated hol 冷藏舱 rig 帆索 rudder 舵 screw 螺丝钉 scupper 排水管 scupper board 挡水板 scanner 雷达扫描设备 sextant 六分仪 shaft tunnel 地轴弄 shackle 钩环 shifting board 防动板,防舱板 signal rocke 信号火箭 siren 汽笛 sling 吊索 starboard 右舷 steam engine 蒸汽引擎 steering gear 舵机 stem 船头 stern 船尾 storeroom 贮藏室 tackle 滑车,吊具 tank 液体舱 ballast tank 压载水舱 cofferdam tank 隔离沧 deep tank 深舱,深水柜 1 船舶专业英语词汇(初级) 1.基本,简单的词汇: AM 上午 PM 下午 Notification of inspection 检查验收通知单 Application 申请,申请单 Inspection 检验,报验 Technical discussion 技术讨论 On board 在船上 In the workshop 在车间 On the slipway 在船台上 At pier(wharf) 在码头 Fair 尚好的 The performance is merely fair 性能尚好 Terrible 极坏的,很糟的 So so 马马虎虎 So far ,so good 到目前,一切顺利 Worse 更糟的 worst 最差、最糟 Improvement 改进 Leave no room for improvement 完美,无缺点 Accept 接收 Accept subject to 有条件的接收,有待于……做好之后才接收 Reject 拒收 Comments 意见 defect lish 消除意见清单 Item 项目 memorandum 备忘录 manual n 、手册、说明书;a.手控的,手工的 drawings 图纸 working drawings 施工图 finished drawings 完工图 approved drawings 认可图 drawings for approval 送审认可图 supporting technical doucuments 基础技术文件 sketch 草图 draw a sketch 画草图 up to the standard 达到标准 substandard 低于标准的 crane 吊车 building berth 船台 slipway 船台、下水滑道 dry dock 干无坞 pier 突码头、突堤 wharf 码头 along side (船)靠码头 foreman 工长,领班 coordinator 调度员 inspector 检查员 supervisor 管理人、监督人,监造人 surveyor 验船师 2、船体总体,及各类型船舶 Hull 船体 Forecastle 艏楼 Stern 船尾 Poop 艉楼 Superstructure 上层建筑 Foremast 前桅杆 After mast 后桅杆 Radar mast 雷达桅杆 Main deck 主甲板 Upper deck 上甲板 Poop deck 艉楼甲板 Accommodation deck 生活甲板 Compass deck 罗经甲板 Funnel 烟囱 Bridge 桥楼,驾驶台 Bridge wing 驾驶室翼桥 Wheel house 驾驶室 Engine room 机舱 Engine control room 机舱集控室 Catwalk 天桥、步桥 Flying bridge (露天)航行驾驶室 Rescue boat 救助艇 Life boat 救生艇M/Vmerchant vessels 商船Naval Auxilary vessel 军用船 Naval Ship/war shipd 军船 Ice-breaker 破冰船Container vessel 集装箱船 Oil tanker 油轮Products tanks 成品油轮Carrier 运输船、航空母舰、托架 Chemical carrier 化学品运输船 Liquefied gas carrier 液化气体船 Liquefied natural gas carrier 液化天然气运输船Aircraft carrier/aeroplane carrier 航空母舰School ship/training ship 训练船Geophysical survey ship 地球物理勘探船Cruiser 巡洋舰、大型快船、游艇 Canoe 独木船,皮舟Junk 平底中国帆船、舳板 Gondola (意大利威尼斯的 )一种狭长的平底船Yacht 快艇、游艇 Fast boat 快艇 Patrol boat 巡逻艇Anti-smuggling boat 缉私艇 Torpedo boat 公安艇 Ferry 渡船Catamaran 双体船 Jet foil 喷水水翼艇Wing assrsted vessel 地效船 3、各专业基本词汇 1)船体:Draft forward 前吃水 Draft middle 中吃水 Draft after 后吃水 Plimsoll mark/line Waterline 吃水线Waterlines (型)水线 Port 左舷 Starboard 右舷Sagging 中垂、下垂、下挂(流) Hogging 中拱、上拱 Derformation 变形Fairing 光顺、火工校正 Hot work 热工、明火作业 section 分段、部分、剖面 Block 分段Keel (船舶)龙骨 Bilge keel 舭龙骨Power tool 带动力工具(风动或电动) Welder 电焊工Welding machine 电焊机A.C welding 交流(电弧)焊 D.C welding 直流(电弧)焊 Grinding 打磨 Welding 电焊Spatters 飞溅(电焊) Under out 咬口 Sharp edge 快口2 船舶专业英语词汇(初级) Deflection 挠曲,变形 Slags 渣..Welding slags 电焊渣Automatic welding 自动焊 Manual welding 手工焊 Arc welding 电弧焊Gas shielded welding 气体保护焊 Inter gas arc welding 惰性气体保护电弧焊Welding seam 焊缝Bending machine 弯曲机Three-roll bending machine 三芯弯板机 Torsional box 抗扭箱 V oid space 空舱 Cofferdam 隔离舱 Bulwark 舷墙,防浪板 Wall 墙壁 Floor 地板Controllable pitch 可调桨 Elastic coupling 弹性联轴节 Bellow 波纹管 Joint 接头 Gaskets 垫片Fitting bolts 拂螺拴 Chock 制动块、导缆器 Chock fast 环氧垫块 Foundation 底座、基座 Mounting 装置、座、架Mount (常指火炮等武器的)座,架 Vent pipe 透气管 Sounding pipe 探测管Vapour return line 油气回路管 Stripping line 扫舱管Safety equipment 安全设备 Life-saving equipment 救生设备 Cargo hold 货舱 Cargo oil tank 货油舱 Cabin 船舱、舱室 Room 房间Store room 储藏室 Cold room 冷库 Fish room 鱼库 Meat room 肉库 Provision room 粮库 Foam room 泡沫库 CO2 room 二氧化碳室 Pump room 泵室Battery room 蓄电池室 Radio room 报务室 Galley 厨房Ventilation system 通风系统Fresh water piping system 淡水系统 Sea water piping system 海水管系 Water jacket 水套Insulation materials 绝缘材料Lagging 绝缘材料、外套(锅炉、管子等) 3)电器 Current 电流 V oltage 电压 Frequency 频率 Contact 触点、触头 Ballast 镇流器Convertor 变频器、换能器 Conductor 导体Semi-conductor 半导体 Rectifier 整流器 Transformer 变压器 Thermostat 恒温器 Thermister 热敏器Edison base 螺丝灯座、爱迪生灯座 Bayonet base 卡口灯座 On-off 开关(量)Analogue 模拟,模拟设备Active analogue 有源模拟、主动模拟 Passive analogue 无源模拟、被动模拟 Dry contact 无源模拟、干接触 Buzzer 蜂鸣器 Button 按扭,电扭 Switch 开关Main switch 主开关Main switch board 主配电板 Cable 电缆 Wire 电线Three-core cable 三蕊电缆 Clamp 夹钳、夹具 Clip 接线柱、线夹Alligator clip 鳄鱼夹、弹簧夹 V oltage drop 电压降 Speed droop 速度降低 Black out 黑灯试验 Power failure 失电 Setting point 设定点 Adjust 调正(v ) Adjustment 调正(n ) Oscillator 振荡器、振动器 Oscilloprobe 示波器测试头 Oscilloscope 示波器、示波仪 Resistor 电阻、电阻器Potentiometer 电位器、电势计 Electrolysis 电解(作用) Electrolyte 电解质、电解液setting point of power surplus 负载余量设定值 重载询问test the power surplus setting point 重载询问试验 4)漆、木Surface preparation 表面处理(清理工作)Blasting equipment 喷漆(砂粒)装置 Sand blasting 喷砂除锈 Pre-blasting 预喷砂 Lingt blasting 预喷砂 Full blasting 通喷砂 Sand sweep 扫砂Sand blasting to SA2.5喷砂达到SA2.5级Steel work inspection after full blasting 通喷砂后钢结构检查Cleanliness inspection 清洁度检查 Inspection after degreasing 除去油脂后检查Removing oil stains by detergent/solvent 使用洗洁剂/容剂除去油迹 Shop primer 车间底漆Spray painting 喷漆、喷涂法 Touch-up 补漆、修正Touch-up painting 补漆、点漆 First coat 底漆、头道漆 Finish coat 面漆Surface coat 表面涂层 Under coat 内涂层 Wearing coat 磨耗层Zinc-rich coating 富锌涂层Cement wash coating (薄)水泥涂层 Stripe coating 预涂层 Floor covering 地板覆层 Alkyd resin paint 醇酸树脂漆Epoxy(resin-based)paint 环氧树脂涂料 3 船舶专业英语词汇(初级) Scuttle 舷窗 Carpet 地毯Wooden skirt 木裙板(踢脚)Aluminum skirt 稆质裙板(踢脚) Brass nose 装于楼梯踏步一的黄铜防滑镶条Stainless screw 不锈钢螺钉 Spring 弹簧Securing dev ice 固定件Locking device 闭锁装置,制动设备 Plywood 胶合板,层压板 Laminated plate 迭层板Laminate 层压制品,迭层板,层压板 High pressure washing of the hull 用高压水冲洗船壳Steel plate temperature 钢板温度 Condensation 冷凝Capillary condensation 毛细管现象 Dew point 露点 Flashing point 闪点Ignition point 燃点,着火点 Ventilation for coating 涂装通风 Dehumidifier 去湿机,干燥机 Dehumidification 去湿,去潮 Sagging 流挂,下垂 Chalking 粉化Peeling 剥落(指油漆) Pinhole 针孔 CureCuring 硬化,熟化,硫化 Drying film thickness(DFT)干膜(漆膜)厚度Curing temperature 硬化、固化温度 Power tools 有动力的工具(包括电动及风动)Pheomatic tools 风动工具 Burnt area 烧坏的区域 Oil stains 油迹 Scratches 划痕Damaged places 遭损坏的部位 Chicken wire 钢丝网 Tiles 瓷砖,瓦Mosaic-tile 彩色瓷砖,镶嵌瓷砖,马赛克瓷砖Glue 胶,粘结剂Silica 硅石,二氧化碳 Silicagel 硅胶Decoration 装饰,装修Interior decoration 内部装饰,内装 Deck head 天花板..Ceiling 天花板Paneling 板墙,镶板 Wall 墙壁Desk 书桌,桌台 Drawer 抽屉Catch hook 固定钩子Observation window 观察窗 Inspection window 检查孔窗 Clear view window 旋转观察窗 Curtain 窗帘Latch 止动销,插销 Valance 窗帘箱 Hanging 窗帘Eyebrow 舷窗眉板 Pre-alarm 预报警 Trip 脱扣,跳闸Preferential trip 优先脱扣 Transducer 换能器synchronize (便)同步 synchronize motor 同步电机 synchronous motor 异步电机 step motor 步进电机 diode 二极管 triode 三极管 audion 三极管 single phase 单相 three phase 三相 phase-in 逐步引进 phase-shafting 相移retarding phase 滞后相位 reversed phase 倒相,相反 relay 继电器 timer 定时器trimmer 微调电容器,调正片 delay 延时carrier 载波,载波电流transponder 发射器,应答器,询问机 echo-sound 回声测深仪radio navigation equipment 无线电导航设备log 计程仪auto-pilot 自动驾驶仪 gyro-compass 电罗经barrier 屏障,障碍,栅栏 zenner barrier 齐纳屏(使电只能单向流的半导体)radio beacon 无线电信标 pluse 脉冲blanking plus 消隐脉冲 induction 感应,感应现象 oscillation 振荡 Leak(v)渗,漏 Leakage(n) 渗,漏Overhaul 大修,彻底检修 Hammer 榔头Spanner 扳手,扳头Ring spanner 环形扳手,梅花扳手 Allen key 内六角扳手, Box spanner 套筒扳手 Torque spanner 扭力扳手Double-ended spanner 双头扳手 Monkey spanner 活络扳手,活络管扳手 Shifting spanner 活络扳手Pipe spanner 管子扳手 Reamer 铰刀Reaming (用)铰(刀扩)孔 Countersink reamer 锥形孔铰刀 Wrench 扳手,扳头 Shisel 凿子Calipers 卡钳,两脚规 Inside calipers 内卡钳 Bore 内孔Boroscopic inspection 内孔表面检查 Boroscope 内孔表面检查仪 Plug 塞(子),(内燃机)火花塞 Cock 施塞,龙头 Valve 阀P/V valve P/V 阀 Strainer 滤器Coarse strainer 粗滤器 Fine strainer 精滤器 Oil separator 分油机 Back pressure 背压 Pressure test 压力试验 Over speed 超速 Over load 超负荷Dafety device 安全装置 Fly wheel 飞轮Floating floor 浮式地板Deckhead 天花板(指由甲板形成的) Ladder 梯子Vertical ladder 直梯 Inclined ladder 斜梯Accommodation ladder 舷梯 Pilot ladder 引水员;软梯 Centering 对中心Alignment 对准,对准中心 Inspection 报验 Installation 安装Final inspection of M/E insallation 主机最终安装报验Inspection of the centering of the stern tabe before fine boring 精镗前艉轴管中心校准Alignment check/inspection 拉中心/校正报验Completeness inspection of the thermal oil circulating piping system 热油循环管系完整性报验Cleanliness inspection after flushing F.O piping system 燃油管串油后清洁检查 Function test of steering gear 舵机效甩试验Hose test of water tight doors 水密门冲水试验Noise lever measurement 噪声测量 Vibration level measurement 振动测量 Main engine (M/E)主机 Generator 发电机Emergency generator 应急发电机 Shaft generator 轴带发电机 Fresh water generator 制淡装置 Steering gear 舵机General service pump 总用泵 Pire pump 消防泵Hydraulic motor 液压马达Hydraulic nuts 液压螺帽 Rudder 舵Rudder bl ade 舵叶Propeller 车叶,螺旋桨Fixed pitch propeller 固定螺距的螺旋桨 Lofting 型线图放样Lay off (船及部件)放样,下料 Plate-cutting 钢板下料,开工Numerically-controlled cutting machine 数控切割机Cutting machine 切割机Under water plasma cutting machine 水下等离子切割机Surface preparation 表面处理 Fabrication (焊)开坡口,边缘加工(如刨边)Upside down construction method 分段装配Assembly 反身建法 Erection 装配,大合拢 Jig 装配架,胎架 Bow jip 船首部胎架Girder 纵向构件,桁(材) Beam 梁,横梁 Sections 型材Profile 型钢(条) Bar 杆,棒,棒材 Plate 板材 Angle bar 角钢I beam (窄缘)工字梁 H beam (宽缘)工字梁 Stiffener 扶强材Bracket 托架,支架,肘板 Support 支架Frame 肋骨,框架 Douler 复板Coaming (舱口)围板,缘材 Sinp 剪切 Cut 切割 Anchor 锚Anchor widdlass 锚机 Anchorage 锚位,锚地 Chain 链Chain block 链条滑车,神仙滑车 Platform 平台Crossover 跨越(梯桥),立交 Life raft 救身筏 Life buoy 救生圈Forward winch 前绞缆机 After winch 后绞缆机 Windlass 锚机 Bitt 带缆桩,系桩Fairlead 导缆钳,导缆孔 Hand rail 扶手,栏杆 Beam 横梁Frame 肋骨,框架 Scantling 构件尺寸 Cargo oil tank 货油舱 Scantling draft 结构吃水 Forepeak tank 首尖舱 After peak tank 尾尖舱Water ballast tanks(W.B.T)压载水舱 Fuel oil tank(F.O.T)燃油舱..Lubricating oil tank(L.OT)滑油舱 Diesel oil tank(D.O.T)柴油舱 Double botton 双层底Double skin 双层外板,双层蒙皮 Bow thruster 艏侧推 Propeller 车叶Fixed pitch propeller 定螺距螺旋桨 Controllable pitch propeller(CPP)可调螺距螺旋桨 Shaft 轴Tail shart 尾轴Shaft generator 轴带发电机 Watertight doors 水密门 Bulwark 舷墙 Bulkhead 舱壁Tank top 内底,液舱顶 Hatch cover 舱口盖 Manhole 人孔Fin stablizer 减摇鳍Antifouling system 防海生物的,防污染系统 Ship 船Vessel 船,舰Fabrication 制造,分段装配(precfabrication 预制,预加工) Assemble 装配,组装Erection 大合拢,船台装配 Staging 脚手架Block stage 分段阶段Mile stone (里程碑,大节点) Plate-cutting 下料,开工Keel-laying 上船台,龙骨铺设 Lauching 下水mooring trial 码头试验,系泊试验 sea trial(sea)试航delivery of the ship 交船defect list by the owner/society 船东提出的消除意见清单/船级社提出的消除意见清单design stage 设计阶段submit drawings to owner,classification society(LR 、DNV 、BV 、ABS ,etc)for approval 向船东,船级社(劳氏,挪威,法国,美国等)提交认可图纸 hull workshop 船体车间machining workshop 金工车间machinery engineering workshop 轮机车间electrical workshop 电气车间 business dept.经营处 perchasing dept.供应处 Q.C.Dept.检验处 Design dept.设计室 Painting and carpenter ’s workshop 漆木车间Project manager 项目经理 Director 指导者,厂长,董事 Managing director 执行董事,常务董事,总经理Head 首长,团长,主任Manager 经理,管理人,干事 Leader 领导者 Meeting 会议Negotiation 谈判 Agreement 协议 Shipyard 船厂 船舶专业英语词汇船舶专业英语词汇(按照字母顺序排列)(一)a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用 accommodation 居住(舱室) accommodation ladder 舷梯 adjust valve 调节阀adjustable-pitch 可调螺距式 admiralty 海军部advance coefficient 进速系数 aerostatic 空气静力学的 aft peak bulkhead 艉尖舱壁 aft peak tank 艉尖舱 aileron 副鳍air cushion vehicle 气垫船 air diffuser 空气扩散器 air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼,翼剖面,机面,方向舵 alignment chock 组装校准用垫楔 aluminum alloy structure 铝合金结构 American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的 anchor arm 锚臂 anchor chain 锚链 anchor crown 锚冠 anchor fluke 锚爪 anchor mouth 锚唇 anchor recess 锚穴 anchor shackle 锚卸扣 anchor stock 锚杆 angle bar 角钢angle of attack 攻角 angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷 anti-pitching fins 减纵摇鳍 antiroll fins 减摇鳍anti-rolling tank 减摇水舱 appendage 附体 artisan 技工assembly line 装配流水线 at-sea replenishment 海上补给 augment of resistance 阻力增额 auxiliary systems 辅机系统 auxiliary tank 调节水舱 axial advance 轴向进速 backing structure 垫衬结构 back-up member 焊接垫板 balance weight 平衡锤ball bearing 滚珠轴承 ball valve 球阀ballast tank 压载水舱 bar 型材bar keel 棒龙骨,方龙骨,矩形龙骨 barge 驳船 baseline 基线basic design 基本设计 batten 压条,板条 beam 船宽,梁beam bracket 横梁肘板 beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线 Benoulli ’s law 伯努利定律 berth term 停泊期 bevel 折角 bidder 投标人 bilge 舭,舱底bilge bracket 舭肘板 bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩 blade root 叶跟blade section 叶元剖面 blast 喷丸block coefficient 方形系数 blue peter 出航旗boarding deck 登艇甲板 boat davit 吊艇架 boat fall 吊艇索 boat guy 稳艇索 bobstay 首斜尾拉索 body plan 横剖面图 bolt 螺栓,上螺栓固定 Bonjean curve 邦戎曲线 boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁 bottom side tank 底边舱 bottom transverse 底列板 boundary layer 边界层 bow line 前体纵剖线 bow wave 艏波 bowsprit 艏斜桅bow-thruster 艏侧推器 box girder 箱桁bracket floor 框架肋板 brake 制动装置 brake band 制动带brake crank arm 制动曲柄 brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸 brake hydraulic pipe 刹车液压管 breadth extreme 最大宽,计算宽度 breadth moulded 型宽 breakbulk 件杂货 breasthook 艏肘板 bridge 桥楼,驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会..buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材 bulb plate 球头扁钢bulbous bow 球状船艏,球鼻首 bulk carrier 散货船bulk oil carrier 散装油轮 bulkhead 舱壁 bulwark 舷墙bulwark plate 舷墙板 bulwark stay 舷墙支撑 buoy tender 航标船 buoyant 浮力的 buoyant box 浮箱Bureau Veritas 法国船级社 butt weld 对缝焊接butterfly screw cap 蝶形螺帽 buttock 后体纵剖线by convention 按照惯例,按约定 大秦cable ship 布缆船 cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程 camber 梁拱cant beam 斜横梁 cant frame 斜肋骨cantilever beam 悬臂梁 capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定 capsize 倾覆capsizing moment 倾覆力臂 captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容,载货容积 cargo handling 货物装卸 carriage 拖车,拖架cast steel stem post 铸钢艏柱 catamaran 高速双体船 catamaran 双体的 cavitation 空泡cavitation number 空泡数 cavitation tunnel 空泡水筒 center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心,重心,质心,矩心 chain cable stopper 制链器 chart 海图charterer 租船人chief engineer 轮机长 chine 舭,舷,脊 chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论 classification society 船级社 cleat 系缆扣clipper bow 飞剪型船首 clutch 离合器coastal cargo 沿海客货轮 cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室,粮食库common carrier 通用运输船 commuter 交通船 compartment 舱室 compass 罗经concept design 概念设计 connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨 constraint condition 约束条件 container 集装箱containerized 集装箱化 contract design 合同设计contra-rotating propellers 对转桨 controllable-pitch 可控螺距式 corrosion 锈蚀,腐蚀 couple 力矩,力偶 crane 克令吊,起重机 crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱 criterion 判据,准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积 crow ’s nest 桅杆瞭望台 cruiser stern 巡洋舰尾 crussing range 航程cup and ball joint 球窝关节 curvature 曲率curves of form 各船形曲线 cushion of air 气垫damage stability 破损稳性 damper 缓冲器 damping 阻尼 davit arm 吊臂deadweight 总载重量 de-ballast 卸除压载deck line at side 甲板边线 deck longitudinal 甲板纵骨 deck stringer 甲板边板 deck transverse 强横梁deckhouse 舱面室,甲板室 deep v hull 深v 型船体 delivery 交船 depth 船深derrick 起重机,吊杆 design margin 设计余量design spiral 设计螺旋循环方式 destroyer 驱逐舰detachable shackle 散合式连接卸扣 detail design 详细设计diagonal stiffener 斜置加强筋 diagram 图,原理图,设计图 diesel engine 柴油机dimensionless ratio 无量纲比值 displacement 排水量displacement type vessel 排水型船 distributed load 分布载荷 division 站,划分,分隔 do work 做功 dock 泊靠double hook 山字钩double iteration procedure 双重迭代法 double roller chock 双滚轮式导览钳 double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索 draft 吃水drag 阻力,拖拽力 drainage 排水draught 吃水,草图,设计图,牵引力 dredge 挖泥船 drift 漂移,偏航 drilling rig 钻架 drillship 钻井船 drive shaft 驱动器轴driving gear box 传动齿轮箱 driving shaft system 传动轴系 dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计,功率计 e.h.p 有效马力eccentric wheel 偏心轮 echo-sounder 回声探深仪 eddy 漩涡eddy-making resistance 漩涡阻力 efficiency 供给能力,供给量 electrohydraulic 电动液压的 electroplater 电镀工 elevations 高度,高程,船型线图的侧面图,立视图,纵剖线图,海拔 empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇 end open link 末端链环 end shackle 末端卸扣 endurance 续航力endurance 续航力,全功率工作时间 engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆 entrance 进流段erection 装配,安装 exhaust valve 排气阀expanded bracket 延伸肘板 expansion joint 伸缩接头 extrapolate 外插 fair 光顺faised floor 升高肋板 fan 鼓风机 fatigue 疲劳feasibility study 可行性研究 feathering blade 顺流变距桨叶。

船舶英语词汇

船舶英语词汇

船舶英语词汇船舶英语词汇目录一、造船部分1、船体部分2、机舱部分3、电气部分4、船装部分二、造机部分三、修造部分一、造船部分1、HULL PART 船体部分1、1 结构Structure船厂dockyard/shipyard 船坞dock/boatyard 船东ship-owner 船舷Ship's side船码头quay/dock 船的栏杆Ship's rail 船舱hold 甲板Deck船籍Ship's registry 住舱甲板accommodation deck 船首bow 梁拱甲板arch deck船梯ladder 载货甲板cargo deck 船尾stern 首楼甲板Forecastle deck 上甲板Upper deck 下甲板Lower deck 主甲板Main deck 货舱甲板Hold deck桥楼甲板Bridge deck水密甲板Watertight deck驾驶甲板Navigation deck 铜-钢复合板Copper sheathing steel plate艇甲板Boat deck 甲板边板Deck stringer plate罗经甲板Compass deck 斜板Sloping plate 板Plate 加强板Reinforcement plate舭板Bilge plate 舵板Rudder plate船底板Bottom plate 舷侧外板Side plate 船外板Shell plate 裙板Skirt plate船首外板Bow plate 首柱板Stem plate肘板Bracket plate 首柱板Stern plate舱壁板Bulkhead plate 平台platform槽形舱壁板Corrugated bulkhead plate 机舱平台Engine-room platform舷墙板Bulwark plate 分段Block围板Coaming plate 首段Bow block连续板Connection plate 中段Midship block尾段Stern block 甲板下纵桁Underdeck girder 左舷port 舭纵桁Wing girder右舷Starboard 支柱Pillar纵桁Girder 肋骨Frame型材桁Bar girder 基础台架Base frame 中底桁Bottom center girder 支架Bear frame中内龙骨Bottom center line girder 舭肋骨Bilge frame底桁材Bottom girder 船底肋骨Bottom frame旁桁材Bottom side girder 首肋骨Bow frame甲板纵桁Deck girder 肘板框架肋骨Bracket frame横桁Cross girder 球鼻首肋骨Bulbous bow frame水平桁Horizontal girder 球曲型肋骨Bulbous frame舱口边梁Hatch coaming girder 主肋骨Chief frame机座纵桁Engine girder 首肋骨Fore frame桁架梁Girder frame 舭纵桁舭纵骨Bilge longitudinal舯部肋骨Middle frame 船底纵骨/纵桁bottom longitudinal尖舱肋骨Peak frame 船底腹板纵桁bottom web longitudinal 加强筋Stiffened frame 甲板纵桁Deck longitudinal横框架肋骨Transverse frame 内底纵桁/纵骨Inner bottom longitudinal肋距F.S.(frame space) 舷侧纵桁/纵骨Shell side longitudinal 纵桁/纵骨/纵向构件longitudinal双层底顶纵骨Top longitudinal of double bottom斜舱壁纵骨Slopping-bulkhead longitudinal舱舷边舱Tank Wing tank结构structure 尾尖舱after peak tank附属结构Accessory structure 尾部水舱after water tank全焊结构All-welded structure 辅助水柜Auxiliary water tank 中部结构Amidships structure 辅助压载水舱Auxiliary water ballast tank 泊位结构Berthing structure 污水舱Bilge tank 底部龙骨结构Bottom keel structure 底舱Bottom tank船首部结构Bow structure 底边舱Bottom side tank支撑结构Braced structure 货油压载舱Cargo and ballast tank 桥楼结构Bridge structure 循环水槽Circulating flow water tank 首楼结构Forecastle structure 循环滑油舱压载水舱Circulating lubricating oil tank Ballast water tank构架结构Framed structure 清洁压载舱Clean ballast tank纵桁结构Girder structure 冷凝水柜Condensate catch tank人孔manhole 干舱Dry tank饮用水舱Drinking water tank 密封圈Sealing ring污水舱Bilge tank 铰链Hinge应急淡水柜Emergency fresh water tank 把手Handle首舱Fore tank 平衡块Balance block首尖舱Fore peak tank斜边舱Hopper side tank 1、2 welding 焊接液舱Liquid tank 坡口groove龙骨舱Keel tank 单面坡口Single groove右舷舱Starboard tank 双面坡口Double groove顶边水舱Topside tank Ⅰ形坡口Square groove顶边翼舱Topside wing tank V 型坡口Single v groove小舱口盖Small hatch cover U 型坡口Single u groove水密舱口盖Water-tight small hatch coverX 形坡口Single v groove风雨密舱口盖Weather-tight small hatch coverK 形坡口Single bevel grooveY 形坡口Single v groove with broad rood face填充金属Filler metal坡口面Groove face 热影响区Heat-affected zone(HAZ)坡口角度Groove angle 过热区Overheated zone焊缝倾角Weld slope 焊合线Bond line(fusion line)接头根部Root of joint 焊接区Weld zone根部间隙Root gap 焊缝区Weld metal area钝边Root face 焊缝weld焊接接头Welding joint 连续焊缝Continuous weld对接接头Butt joint 断续焊缝Intermittent weld角接接头Corner joint 纵向焊缝Longitudinal weldT 形接头T-joint 横向焊缝Transverse weld搭接接头Lap joint 对接焊缝隙Butt weld十字接头Cross shaped joint 角焊缝Filled weld母材Base metal(parent metal) 并列断续角焊缝Chain intermittent fillet交错断续角焊缝Staggered intermittent fillet弧焊整流器Arc welding rectifier焊缝正面Face of weld 自动焊Automatic welding焊缝背面Back of weld 埋弧自动焊Submerged arc welding焊缝宽度Weld width 半自动焊Semi- automatic welding焊缝长度Weld length 氩弧焊Argon-arc welding焊缝余高Reinforcement 二氧化碳气体保护焊CO2 gas shielded arc welding 焊脚Leg(of a fillet weld) 氧乙炔焊Oxy-acetylene welding焊脚长度Leg length 气割Gas cutting套管接头Muff joint 碳弧气刨Carbon arc air gouging手工电弧焊Manual arc welding(shielded metal arc welding) 水下切割Underwater cutting直流电弧焊Direct current arc welding 等离子弧切割Plasma arc cutting交流电弧焊alternating current arc welding连续焊Continuous welding弧焊变压器Arc welding transformer 断续焊Intermittent welding点焊Sport welding对接焊Butt welding 分段退焊Back step welding角焊Fillet welding 分段多层焊Block welding搭接焊Lap welding 深溶焊Deep penetrating welding返修焊Re-welding 跳焊Skip welding补焊Repair welding 陶质衬垫焊Ceramic backing welding定位焊Tack welding 引弧Striking the arc封底焊Back sealing welding 焊接工艺参数Welding condition 打底焊Backing welding 焊接电流Welding current堆焊Surfacing(overlaying) 焊接电压Welding voltage塞焊Plug welding 焊接速度Welding speed槽焊Slot welding 电弧电压Arc voltage盖面焊Consmetic welding 焊丝间距Wire spacing前倾焊Forward welding 空载电压Open circuit voltage后倾焊Backward welding 熔化速度Melting rate送丝速度Wire feed rate 层间温度Inter-pass temperature气体流量Gas flow rate 焊后热处理Post-weld heat treatment 焊丝伸出长度Wire extension 锤击Peening极性Polarity 全焊透Full penetration welding正极/阳极Positive electrode 熔池Weld-pool负极/阴极Navigate electrode 熔深Penetration左焊法Leftward welding 弧长Arc length右焊法Rightward welding 喷射过渡Spray transfer电流密度Current density 短路过渡Short circuiting transfer线能量Heat input 熔滴过渡Metal transfer预热Preheat 焊缝成形Appearance of weld后热Post-heat 焊缝成形系数Form factor of weld预热温度Preheat temperature 熔敷系数Deposition coeffcient 后热温度Post-heat temperature 熔敷效率Deposition efficiency熔合比Penetration ratio 立焊Vertical position welding等速送丝Constant wire-feed system 仰焊Overhead position welding 变速送丝alternate wire-feed system 立向上焊Vertical up welding 电弧静特性Static characteristic of arc立向下焊Vertical down welding电弧动特性dynamic characteristic of arc单面焊Welding by one side焊接性试验Weldability test 双面焊Welding by both side焊接结构Welded construction 单道焊Single-pass welding焊道Bead 多道焊Multi-pass welding焊层Layer 多层焊Multi-layer welding正接(正极性)Straight polarity 焊接材料Consumables反接(反极性)Reversed polarity 焊条Electrode焊接位置Position of welding 焊条药皮Coating平焊Flat position welding 酸性焊条Acid electrode横焊Horizontal position welding 碱性焊条Basic electrode低氢型焊条Low hydrogen type electrode 焊丝盘Wire reel铁粉性焊条Iron power type electrode 铜冷却板Cu-cooling plate重力焊条Gravity electrode 铜滑块Copper shoe焊剂Flux 切割Cutting熔炼焊剂Fused flux 焊接工作台Welding bench烧结焊剂Sintered flux 焊接变位机Positioner焊丝Wire 送丝机构Wire feeder药芯焊剂Flux-cored wire 行走机构Traveler保护气体Shielded gas 焊接车间Welding shop焊剂垫Flux backing 引弧板Run-on tab(end tab)重力焊条Gravity electrode 引出板Run-off tab(end tab)焊剂漏斗Flux-hopper 定位板Strong-back流量计Flow meter 焊接衬垫Welding backing干燥箱Dryer 敲渣锤Chipping hammer面罩Helmet 条虫状气孔Wormhole焊工手套Welding glove 密集气孔Porosity焊钳Electrode holder 针尖状气孔Pinhole焊枪Welding gun 白点Fish eye (flake)导电嘴Tip 切口Kerf喷嘴Nozzle 咬边Undercut焊矩Torch 焊瘤overlap焊接缺陷Welding defect 凹坑Pit未焊透Incomplete penetration 烧穿Burn through未熔合Incomplete fusion 未满焊Incomplete filled groove 渣Slag 清根Back chipping夹渣Slag (slag inclusion) 清渣Slag removal夹杂物Inclusion 焊接烟尘Weld fume气孔Blow hole 电光性眼炎Eye-flash焊接性Weldability 横裂纹Transverse crack碳当量Carbon equivalent 纵裂纹Longitudinal crack未焊满Incomplete filled groove 焊趾裂纹Toe crack焊接裂纹Weld crack 机械性能试验Mechanical property test 热裂纹Hot crack 试板Test piece冷裂纹Cold crack 试样Specimen氢致裂纹Hydrogen –induced crack 侧弯Side bend延迟裂纹Delayed crack 弯曲Bending层状撕裂Lemellar tearing 横向拉伸Transverse tensile弧坑裂纹Crater crack 宏观试样Macro-etching specimen根部裂纹Root crack 微观试样Micro-examination specimen 再热裂纹Reheat crack 破断试验Fracture test热影响区裂纹Heat-effected zone crack 抗裂试验Cracking test 晶间裂纹Intercystalline crack 脆性断裂Brittle fracture塑性断裂Plastic fracture 焊接方法Welding process焊接残余裂纹Welding residual stress 焊接工艺Welding technology消除应力Stress relieving 焊接操作Welding operation焊接变形Welding deformation 焊接顺序Welding sequence 角变形Angular distortion 焊接方向Direction of welding外观检查Visual examination 常用缩语无损探伤Non-destruction testing(N.D.T.)气电立焊EGW超声波探伤Ultrasonic inspection 药芯电弧焊FCAW射线探伤(X 光)Radiographic inspection(X-rayinspection) 实心电弧焊GMAW磁粉探险伤Magnetic particle inspection焊剂铜衬垫单面埋弧自动焊FCB渗透探伤Penetrate inspection 手工电弧焊SMAW熔池Weld-pool 埋弧自动焊SAW焊机(焊接电源)Weld source钨极惰性气体保护电弧焊TIG 机舱部分ENGINE ROOM PART熔化极惰性气体保护焊MIG 一、机舱设备Machines and equipment in engine room 活性气体保护焊MAG 1、主机Main engine手工电弧切割SMAC 1)主机油底壳The sump tank of M.E.2)主机飞轮Fly wheel of M.E3)活塞Piston2、发电机Generator engine1)应急发电机Emergency generator engine2)辅机Auxiliary3、锅炉Boiler1)组合锅炉The composite boiler2)锅炉安全阀The safety valve of boiler3)燃烧器Oil burner unit 3)主空气瓶Main air reservoir4)水位表Water level gauge 4)应急空气瓶Emergency air reservoir5)水位控制器Water level controller 5、控制空气瓶Control air reservoir6)过量蒸气调节阀Excess steam pressure control valve6、空气干燥器Air dryer4、舵机7、分油机Oil purifier1)舵机间Steering room 1)燃油分油机Fuel oil purifier2)舵机装置Steering-gear 2)柴油分油机Diesel oil purifier3)手操舵装置Trick wheel plant 3)滑油分油机Lubricate oil purifier4)油缸Oil cylinder 4)排渣Sludge discharge5)反馈装置Feedback device 8、制淡装置Fresh water generator6)舵Rudder9、焚烧炉Incinerator舵叶Rudder blade10、油水分离器Oil water separator舵杆Rudder stock11、生活污水处理器Sewage treat plant上舵承Rudder carrier12、大气冷凝器Atmosphere condenser热水井Cascade and inspection(hotwell)5)主机燃油供给泵Main engine fuel oil supply pump滑油自清滤器The automatic back-flashlubricating oil filter6)主机燃油增压泵Main engine fuel oil booster pump燃油单元Fuel oil unit 7)主机十字头泵Main engine cross head pump1)主机燃油单元Fuel oil unit of M.E 8)付机海水泵Generator engine sea water pump2)付机燃油单元Fuel oil unit of A.E 9)付机缸套水泵Generator engine cylinder cooling water pump3)粘度计Viscosity controller 10)锅炉给水泵Feed water pump of boiler泵Pump 11)锅炉燃油泵Fuel oil pump of boiler1)主机滑油泵Main engine lubricating oil pump12)分油机供给泵Fuel oil supply pump of purifier2)主机缸套水泵Main engine cylinder cooling water pump 13)制淡海水泵Sea water pump of fresh water generator3)主机缸套水预热泵Main engine cylinder cooling water preheating pump14)压载泵Ballast pump4)主机海水泵Main engine sea water pump 15)舱底消防泵Bilge and fire pump17)油渣泵Sludge oil pump 2、柴油澄清舱Diesel oil setting tank18)柴油输送泵Diesel oil transport pump 3、燃油日用柜Fuel oil daily tank19)燃油油输送泵Fuel oil transport pump 4、燃油澄清舱Fuel oil setting tank20)汽缸油输送泵Cylinder oil transport pump 5、滑油澄清舱Lubricating oil setting tank 21)淡水输送泵Fresh water transport pump 6、滑油储藏舱Lubricating oil store tank 22)热水循环泵Hotwater circulating pump 7、滑油循环舱Lubricating oil circulating tank 23)饮水日用泵Drinking water pump 8、燃油溢油舱Fuel oil overflow tank舱底消防总用泵Bilge, fire and G.S pump 9、燃油油渣舱Fuel oil sludge tank喷淋泵Sprinkling pump 10 燃油深舱Fuel oil deep tank停泊海水泵Harbor sea water pump 11 滑油污油舱Lubricating dirty oil tank12 滑油溢油舱Lubricating oil overflow tank二、各种舱(箱)柜All kinds of tank 13 滑油油渣打舱Lubricating oil sludge tank1、柴油日用柜Diesel oil daily tank 14 主机淡水膨胀水箱M.E fresh water expansion tank15 付机淡水膨胀水箱A.E fresh water expansion tank16、淡水压力柜Fresh water pressure tank 1、滑油系统Lubricating oil piping system17、热水压力柜Hot water pressure tank 2、燃油系统Fuel oil piping system18、饮水压力柜Drinking water pressure tank3、海水系统Sea water piping system19、淡水舱Fresh water tank 4、缸套水系统Cylinder cooling water piping system20、饮水舱Drinking water tank 5、启动空气系统Start air piping system21、锅炉水舱Boiler water tank 6、控制空气系统Control air piping system22、分油机工作水箱Purify operating water tank 7、排气系统Exhaust piping system23、汽缸油日用柜Cylinder oil daily tank 8、日用供水系统Daily water piping system24、尾管滑油重力柜Gravity tank of tube oil 9、蒸汽系统Steam piping system25、排气水封箱Exhaust seal water tank 10 、锅炉给水和凝水系统Feed water and condensate of boiler piping system26、蒸馏水水舱Distilling water tank 11、燃油净油系统Fuel oil purified piping system27、污水井Bilge well 12、燃油输送系统Fuel oil transport piping system三、各种管系系统All kinds of pipes舵销Rudder pintle 13、滑油净油系统Lubricating oil purified piping system舵杆衬套rudder stock liner 14、滑油输送系统Lubricating oil transport piping system舵杆轴套Sleeve for rudder stock 15、舱底压载系统Ballast and bilge water piping system 舵销承衬套Bush for rudder pintle 四、仪表类Instructions舵销轴套Sleeve for rudder pintle 1、压力表Pressure gauge 上舵承底座Rudder carrier seat 2、真空表Vacuum gauge舵销承座Pintle bearing 3、温度计Thermometer舵杆承座Rudder stock bearing 4、吨位表DWT gauge挡圈Retaining ring 5、遥测表Distant survey gauge舵柄Tiller 6、液全器Level switch7)舵角The angle of rudder5、空压机Air compressor1)主空压机Emergency air compressor2)应急空压机7、传感器Sensor 12、机控室Engine control room五、其它Others 13、台虎钳Vise (=vice)1、风机Fan 14、表铜截止阀Bronze close valve2、防海生物装置Anti-foul STM plant 15、表铜截止止回阀Bronze check valve3、泡沫柜Air foam tank 16、铸铁截止阀Cast iron stop valve4、中间轴Middle shaft 17、铸铁截止止回阀Cast iron check and stop valve5、尾轴Propeller shaft 18、调节阀Adjustable valve6、螺旋桨Propeller 19、溢流阀、安全阀Relief valve7、中间轴承Line shaft bearing 20、减压阀Reducing valve8、泡沫灭火机Foam fire extinguisher 六、材料Material9、饮水消毒装置Sterilizer plant 1、管子Pipe10、主配电板Main switch board 2、无缝钢管Seamless steel pipe (tube)11、机舱集控台Engine room control console 3、紫铜管Purple copper pipe4、铁法兰Iron flange 18、支架(马脚)Clamp5、铜法兰Copper flange 19、油漆Paint6、盲板法兰Blind-flange 20、备件Spare parts7、螺丝(螺栓)Bolt8、双头螺丝Stud 七、生产工具Produce tool9、螺帽(螺母)Nut 1、图纸Drawing10、不锈钢螺丝Stainless steel bolt 2、活络钣Adjustable spanner11、垫片(床)Gasket 3、令司板(梅花钣)Ring spanner12、橡皮床Gum gasket 4、开口钣Open –ender spanner13、纸箔床Paper copper gasket 5、管子钳Pipe wrench14、紫铜床Purple copper gasket 6、凿子Chisel15、石墨床Black lead gasket 7、锒头Hammer16、青铅床Black lead gasket 8、锉刀File17、佛纳Feeler gauge 9、螺丝刀Screwdriver10、油漆滚筒Paint roller 4、首先请检查安装说明和电气绝缘11、油漆刷子Paint brush Please check the condition of installation and insulationfirst12、钢锯Hacksaw 5、我们准备将油水分离器动转13、套筒扳手Socket spanner Now we will run the oily-water separator14、手电筒Torch 6、请检查动转情况15、钻头driller Please check the running condition八、英语会话7、接着我们一个一个地做报警/安全保护装置的功能试验1、早上好good morning Now we will do the function test about alarm and safetydevice2、今天我们准备交验油水分离器8、设备交接基本结束Today we will test the oily-water separator. Now the test is over3、请跟我来9、请部有何修改意见?Please fellow me. Do you have any question ?10、非常感谢17、这里增加一只落水斗Thanks Add a drain plug here11、再见18、请用空气压缩空气吹干Good bye Please dry it by the compressed air12、请把这对法兰撬紧松开19、我将回车间支拿肥皂水Please tighten/release the flange I will com to my workshop to take some soap water13、这路管子是从发电机单元来的20、这个系统非常重要的,一定要认真检查The piping is from to the G/E unit This system is very important ,please check it carefully14、这对法兰/接头在漏21、请交验收整改意见This flange /connection is linking Please check your remarks15、这路系统的试验压力是7 公斤22、天太热了,请休息一会The test pressure of the piping system is 7 bar It’s too hot ,please take a rest16、这里请加强please make a clamp here 23、我负责这项工作I am in charge of this job电气部分ELECTRIC PART一、常用词汇Words and expression 模拟Analog(ue)2182 千赫值班接收机2182KHz watch receiver 锚灯Anchor lightA 异常Abnormal 风速风向仪Anemorumbometer应答Acknowledge 阳极Anode有功功率Active power 天线Antenna执行器Actuator 天线馈线连接器Antenna feeder connector调整Adjust 天线引入绝缘端子Antenna leading –in insulator 空气断路器Air circuit breaker 天线共用器Antenna multicoupler报警系统Alarm system 天线调谐器Antenna tuner交流电Alternating current 电焊机Arc welder电流表ammeter 声音的Audible放大器Amplifier 自动海图标绘仪Auto chart plotter自动舵Auto pilot自动的Automatic自动雷达标绘仪Automatic radar plotting aid球鼻首警告灯Bulbous bow warning light自动电话Automatic telephone 汇流排Bus(-)bar电压自动调节器Automatic voltage regulator 汇流排Bus –tie –in自动化系统Automation system 蜂鸣器Buzzer压载控制台Ballast control console C、电缆Cable镇流器Ballast 电缆填料函Cable gland底座Base 敷设电缆Cable laying电池Battery 电缆管Cable pipe (conduit)铃Bell 电缆扎带Cable strap弯曲Bend 电缆托架Cable tray床头灯Berth light 校准器Calibrator失电Black out 电容capacitor刹车Brake 阴板Cathode电刷Brush 警告牌Caution plate顶灯Ceiling light 通讯Communication中央处理器Central processing unit 计算机Computer通道Channel 接头Connector充电器Charger 恒电流Constant current充放电板Charging&discharging board 消耗Consumption海图灯Chart table light 触头Contact检查Check 接触器Contactor芯片Chip 控制箱Control box清洁Clean 控制箱Controller雨雪清除器Clear view screen 芯线Core二氧化碳释放报警CO2 release alarm 角灯Corner light同轴电缆Coaxial cable 计算器Counter线圈Coil 电流Current冷库呼叫Cold store calling D、损坏Damage危险气体报警箱Dangerous gas detecting&alarm box双极单刀开关Double pole single way switch白昼信号灯Daylight signal light 双极双刀开关Double pole two way switch 去耦Decoupling set 天线收发转换开关Duplexer 台灯Desk light 值班水手呼叫Duty sailor calling控测器Detector 接地Earth拨号Dial 接地排Earth bar数字选择呼叫收信机Digital select –call receiver测深仪Echo sounder调光器dimmer 电工试验板Electric test panel直流电Direct current 电机员Electrical engineer直接起动Direct –on –line starting 电极Electrode磁盘Disk 应急照明分电箱Emergence lighting distribution box 显示Display 应急示位标Emergence position indicating radiobeacon遇险信息控制器Distress message controller 应急停Emergence stop多普勒记程仪Doppler speed log应急配电板Emergency switch board 馈电品Feeder panel机舱报警Engine alarm 滤波器Filter集控台Engine control console 火警复显器Fire alarm repeater 机舱监测报警Engine room monitoring&alarm system防火风闸控制单元Fire damper control unit轮机员呼叫Engineer calling panel 火警检测箱Fire detecting box轮机员安全Engineer safety system 火焰探头Flame detector 增强群呼叫收讯机Enhance group call receiver 闪光灯Flash light交换机Exchanger 浮充电Float charge防爆灯Explosion proof light 强光灯Flood light延伸报警板Extension alarm panel 流程图Flow chart故障Failure 流量开关Flow switch故障Fault 荧光灯Fluorescent light反馈Feed back 雾笛Fog horn频率Frequency熔丝Fuse 感温探头Heat detector填料Gasket 底座Holder通用报警General alarm 电笛、喇叭Horn发电机Generator 病房呼叫Hospital calling发电机屏Generator panel 照明Illumination(铜)锣、钟Gong 白炽灯Incandescent light全球卫星定位导航GPS navigator 指示器Indicator组合灯板Group alarm light pillar 卫星B 站INMARSAT B station组合起动屏Group starter panel 卫星C 站INMARSAT C station 电罗经Gyro compass 输入输出Input /output卤素灯Halogen light 安装Install听筒Handset 仪表Instrument硬件Hardware 绝缘胶带Insulating tape航向Heading 绝缘Insulation接口、界面Interface 限位开关Limit switch连锁Interlock 连接Link中断Interrupt 负载Load逆变器Inverter 劳莱收信机Loran receiver接线盒Junction box 磁罗经Magnetic compass键盘Keyboard 主机电子调速器Main engine electronic governor灯泡Lamp 主机功率、纽力仪Main engine power& torque unit 液位开关Level switch 主机遥控系统Main engine remote control system液位传感器Level transmitter 主机转速表Main engine revolution meter灯Light 主机安全系统Main engine safety system灯柱Light column 主机增压器转速表Main engine turbo-charger speed meter 照明分电箱Light distribution box 主配电板Main switchboard避雷针Lighting arrester 手动手册Manual标记Mark 移动Move桅杆Mast light 万用表Multimeter母子钟Master& slave clock 铭牌Name plate匹配箱Matching box 窄频直接打印机Narrow-band direct printer测量Measure 航行灯Navigation light兆欧表Megohmmeter 导航系统Navigation system仪表Meter 航行监控台Navigation watch console话筒Microphone 航行警告收信机NA VTEX receiver镜向灯Mirror light 负极Negative监视器Monitor 网络Network莫斯键Morse key 标称值Nominal value电动机Motor 常闭Normally closed塑壳断路器Moulded case circuitbreaker常开Normally open鼠标Mouse 失控灯Not under-command light欧姆表Ohm gauge 正极Positive欧姆收信机Omega receiver 功率、电源Power车钟记录仪Order printer 电力分电箱Power distribution box 示波器Oscilloscope 功率因素Power factor过电流Over current 优先卸载Preferential trip过载Overload 压力开关Pressure switch巴拿马动河操舵灯Panama canal steering light 压力传感器Pressure switch 并联、并车Parallel 一次系统Primary system 相Phase 打印机Printer光敏电阻Photo resister 程序Program测速传感器Pick up 螺旋桨警告灯Propeller warning light插头Plug 广播Public addressor左舷灯Port light 脉冲Pulse便携电话Portable telephone 按钮Push button雷达Radar 电阻Resistance雷达应答器Radar transponder 逆功率Reverse power收音机Radio 旋转灯Rotating light无线电测向仪Radio direction finder 舵角指示器Rudder angle indicator随机存取存储器Radio system 运转灯Running lamp额定Random access memory 屏幕、屏蔽Screen无功电流Rated power 螺丝刀Screwdriver插座Receptacle 搜索灯Search light录音机、记录仪Recorder 二次系统Secondary system整流器Rectifier 串联Series继电器Relay 屏蔽Shield复位Reset 船名灯Ship name light岸电箱Shore connection box短路Short circuit展示、给-----看Show 电磁阀Solenoid valve分励脱扣Shunt trip 消音Sound off停车Shut down 声力电话Sound power telephone签字Sign 空间加热器Space heater信号集合箱Signal acquisition unit 扳手Spanner信号灯Signal light 喇叭Speaker单边带收发机Single side band transceiver分配器Distributor电笛Siren 右舷灯Starboard light慢车Slow down 起动Start烟气探测报警箱Smoke detecting &alarm box 起动带Start感烟探头Smoke detector 尾灯Stern light插座Socket 停止Stop软件Software 苏伊士运河尾灯Suez canal stern light电烙铁Soldering iron 支撑物supporter开关Switch 验电笔Test pen打开Switch on 试验程序T est procedure关闭Switch off 热敏电阻Thermistor同步屏Synchronizing panel 热电偶Thermocouple同步表Synchronoscope 温度计Thermometer转速表Tachometer 恒温计Thermostat录音机Tape recorder 触摸屏T ouch panel车钟Telegraph 轨迹球Trackball电视Television 收发机Transceiver温度开关Temperature switch 传感器Transmitter温度传感器T emperature transmitter 变压器Transformer接线柱T erminal 脱扣Trip接线排T erminal board 欠电压Under voltage试验Test 不中断电源Uninterrupted power source卸载Unload 二、会话Dialog and conversation超高频VHF telephone 船东o- owner视觉的Visual 验船师s-survey电压V oltage 检验员q-quality inspector电压表Voltmeter 电工e-electrician壁灯Wall light 1、检验电缆敷设瓦特Watt Inspection cable laying波道Waveguide 你能带我去看机舱电缆敷设气象传真收信机Weather fax receiver Q: could you show me cable laying of engine room?驾控台Wheel speed &directionindicator好,走吧。

船舶专用英语汇总

船舶专用英语汇总

船舶专业英文词汇No.1船舶专业英语词汇(按照字母顺序排列)(一)a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住(舱室)accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼,翼剖面,机面,方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨,方龙骨,矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条,板条beam 船宽,梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭,舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓,上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽,计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼,驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏,球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例,按约定船舶专业英语词汇(按照字母顺序排列)(二)cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容,载货容积cargo handling 货物装卸carriage 拖车,拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心,重心,质心,矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭,舷,脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室,粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀,腐蚀couple 力矩,力偶crane 克令吊,起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据,准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室,甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机,吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图,原理图,设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站,划分,分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力,拖拽力drainage 排水draught 吃水,草图,设计图,牵引力dredge 挖泥船drift 漂移,偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计,功率计船舶专业英语词汇(按照字母顺序排列)(三)e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力,供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度,高程,船型线图的侧面图,立视图,纵剖线图,海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力,全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配,安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮,渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边,法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘,外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型,流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件,锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨,框架,桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁,桁架girder of foundation 基座纵桁governmental authorities 政府当局,管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书,19世纪英国另一船级社的船名录,现合并与劳埃德船级社,用于登录快速远洋船gross ton 长吨(1.016公吨)group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇(按照字母顺序排列)(四)half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的,螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂,轴毂,套筒hull form 船型,船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖,通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水,浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的,加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点,交*,横断(切)inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射,下水launch 汽艇launching equipmeng (向水中)投放设备LCC 大型原油轮leading edge 导缘,导边ledge 副梁材length overall 总长leveler 调平器,矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约,规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵(横)稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械(主机)卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的,海运的,靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单,物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇(按照字母顺序排列)(五)N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机,准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴,中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的,正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽,开凹口oar 橹,桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构,抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱,垂直的,正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销,枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头,停泊所quotation 报价单船舶专业英语词汇(按照字母顺序排列)(六)racking 倾斜,变形,船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register (船舶)登录簿,船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂,恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接,铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺,尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面,横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切,剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨,导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt (气垫船)围裙slamming 砰击sleeve 套管,套筒,套环slewing hydraulic motor 回转液压马达slice 一部分,薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置,舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道,尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲,加强stiffener 扶强材,加劲杆straddle 跨立,外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱,支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人,总段长,车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖,越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇(按照字母顺序排列)(七)tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的,正切的tangential viscous force 切向粘性力tanker 油船tee T型构件,三通管tender 交通小艇tensile stress 拉(张)应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器,助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home (船侧)内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter (海运)保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶(摆线)推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流,尾流water jet 喷水(推进)管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器,消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨(游艇)working allowance 有效使用修正量worm gear 蜗轮,蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇来自:navigation > 《ship》上一篇:船舶保安员工作要点下一篇:海洋运输常用英文缩略语转藏到我的图书馆献花(1) 分享到微信以文找文分享:人人网开心网搜狐微博推荐给朋友举报类似文章更多•船舶专业英语词汇•船体制图常用英中名词术语对照•船舶英语(页1) - 设计学习- 千岛热线论....•船体结构英语•船舶英语手册1--5•Navis.gr - 3Examination Questions For...•船舶图纸符号大全•货运保险鉴定常用词汇。

船舶英语词汇

船舶英语词汇

船舶英语词汇目录一、造船部分1、船体部分2、机舱部分3、电气部分4、船装部分二、造机部分三、修造部分一、造船部分1、HULL PART船体部分1、1结构Structure船厂dockyard/shipyard船坞dock/boatyard船东ship-owner船舷Ship's side船码头quay/dock船的栏杆Ship's rail船舱hold甲板Deck船籍Ship's registry住舱甲板accommodation deck船首bow梁拱甲板arch deck船梯ladder载货甲板cargo deck船尾stern首楼甲板Forecastle deck上甲板Upper deck 下甲板Lower deck主甲板Main deck货舱甲板Hold deck桥楼甲板Bridge deck水密甲板Watertight deck驾驶甲板Navigation deck铜-钢复合板Copper sheathing steel plate艇甲板Boat deck甲板边板Deck stringer plate罗经甲板Compass deck斜板Sloping plate 板Plate加强板Reinforcement plate舭板Bilge plate舵板Rudder plate船底板Bottom plate舷侧外板Side plate船外板Shell plate裙板Skirt plate船首外板Bow plate首柱板Stem plate肘板Bracket plate首柱板Stern plate舱壁板Bulkhead plate平台platform槽形舱壁板Corrugated bulkhead plate机舱平台Engine-room platform舷墙板Bulwark plate分段Block围板Coaming plate首段Bow block连续板Connection plate中段Midship block尾段Stern block甲板下纵桁Underdeck girder 左舷port舭纵桁Wing girder右舷Starboard支柱Pillar纵桁Girder肋骨Frame型材桁Bar girder基础台架Base frame中底桁Bottom center girder支架Bear frame中内龙骨Bottom center line girder 舭肋骨Bilge frame底桁材Bottom girder船底肋骨Bottom frame旁桁材Bottom side girder首肋骨Bow frame甲板纵桁Deck girder肘板框架肋骨Bracket frame横桁Cross girder球鼻首肋骨Bulbous bow frame水平桁Horizontal girder球曲型肋骨Bulbous frame舱口边梁Hatch coaming girder主肋骨Chief frame机座纵桁Engine girder首肋骨Fore frame桁架梁Girder frame舭纵桁舭纵骨Bilge longitudinal舯部肋骨Middle frame船底纵骨/纵桁bottom longitudinal尖舱肋骨Peak frame船底腹板纵桁bottom web longitudinal加强筋Stiffened frame甲板纵桁Deck longitudinal横框架肋骨Transverse frame内底纵桁/纵骨Inner bottom longitudinal肋距 F.S.(frame space)舷侧纵桁/纵骨Shell side longitudinal纵桁/纵骨/纵向构件longitudinal双层底顶纵骨Top longitudinal of double bottom斜舱壁纵骨Slopping-bulkhead longitudinal舱舷边舱Tank Wing tank结构structure尾尖舱after peak tank附属结构Accessory structure尾部水舱after water tank全焊结构All-welded structure辅助水柜Auxiliary water tank中部结构Amidships structure辅助压载水舱Auxiliary water ballast tank 泊位结构Berthing structure污水舱Bilge tank底部龙骨结构Bottom keel structure底舱Bottom tank船首部结构Bow structure底边舱Bottom side tank支撑结构Braced structure货油压载舱Cargo and ballast tank桥楼结构Bridge structure循环水槽Circulating flow water tank首楼结构Forecastle structure循环滑油舱压载水舱Circulating lubricating oil tank Ballast water tank构架结构Framed structure清洁压载舱Clean ballast tank纵桁结构Girder structure冷凝水柜Condensate catch tank人孔manhole干舱Dry tank饮用水舱Drinking water tank密封圈Sealing ring污水舱Bilge tank铰链Hinge应急淡水柜Emergency fresh water tank把手Handle首舱Fore tank平衡块Balance block首尖舱Fore peak tank斜边舱Hopper side tank1、2welding焊接液舱Liquid tank坡口groove龙骨舱Keel tank单面坡口Single groove右舷舱Starboard tank双面坡口Double groove顶边水舱Topside tankⅠ形坡口Square groove顶边翼舱Topside wing tank V型坡口Single v groove小舱口盖Small hatch cover U型坡口Single u groove水密舱口盖Water-tight small hatch coverX形坡口Single v groove风雨密舱口盖Weather-tight small hatch coverK形坡口Single bevel grooveY形坡口Single v groove with broad rood face填充金属Filler metal坡口面Groove face热影响区Heat-affected zone(HAZ)坡口角度Groove angle过热区Overheated zone焊缝倾角Weld slope焊合线Bond line(fusion line)接头根部Root of joint焊接区Weld zone根部间隙Root gap焊缝区Weld metal area钝边Root face焊缝weld焊接接头Welding joint连续焊缝Continuous weld对接接头Butt joint断续焊缝Intermittent weld角接接头Corner joint纵向焊缝Longitudinal weldT形接头T-joint横向焊缝Transverse weld搭接接头Lap joint对接焊缝隙Butt weld十字接头Cross shaped joint角焊缝Filled weld母材Base metal(parent metal)并列断续角焊缝Chain intermittent fillet交错断续角焊缝Staggered intermittent fillet弧焊整流器Arc welding rectifier焊缝正面Face of weld自动焊Automatic welding焊缝背面Back of weld埋弧自动焊Submerged arc welding焊缝宽度Weld width半自动焊Semi-automatic welding焊缝长度Weld length氩弧焊Argon-arc welding焊缝余高Reinforcement二氧化碳气体保护焊CO2gas shielded arc welding 焊脚Leg(of a fillet weld)氧乙炔焊Oxy-acetylene welding焊脚长度Leg length气割Gas cutting套管接头Muff joint碳弧气刨Carbon arc air gouging手工电弧焊Manual arc welding(shielded metal arc welding)水下切割Underwater cutting直流电弧焊Direct current arc welding等离子弧切割Plasma arc cutting交流电弧焊alternating current arc welding连续焊Continuous welding弧焊变压器Arc welding transformer断续焊Intermittent welding点焊Sport welding对接焊Butt welding分段退焊Back step welding角焊Fillet welding分段多层焊Block welding搭接焊Lap welding深溶焊Deep penetrating welding返修焊Re-welding跳焊Skip welding补焊Repair welding陶质衬垫焊Ceramic backing welding定位焊Tack welding引弧Striking the arc封底焊Back sealing welding焊接工艺参数Welding condition打底焊Backing welding焊接电流Welding current堆焊Surfacing(overlaying)焊接电压Welding voltage塞焊Plug welding焊接速度Welding speed槽焊Slot welding电弧电压Arc voltage盖面焊Consmetic welding焊丝间距Wire spacing前倾焊Forward welding空载电压Open circuit voltage后倾焊Backward welding熔化速度Melting rate送丝速度Wire feed rate层间温度Inter-pass temperature气体流量Gas flow rate焊后热处理Post-weld heat treatment焊丝伸出长度Wire extension锤击Peening极性Polarity全焊透Full penetration welding正极/阳极Positive electrode熔池Weld-pool负极/阴极Navigate electrode熔深Penetration左焊法Leftward welding弧长Arc length右焊法Rightward welding喷射过渡Spray transfer电流密度Current density短路过渡Short circuiting transfer线能量Heat input熔滴过渡Metal transfer预热Preheat焊缝成形Appearance of weld后热Post-heat焊缝成形系数Form factor of weld预热温度Preheat temperature熔敷系数Deposition coeffcient后热温度Post-heat temperature熔敷效率Deposition efficiency熔合比Penetration ratio立焊Vertical position welding等速送丝Constant wire-feed system仰焊Overhead position welding 变速送丝alternate wire-feed system立向上焊Vertical up welding电弧静特性Static characteristic of arc立向下焊Vertical down welding电弧动特性dynamic characteristic of arc单面焊Welding by one side焊接性试验Weldability test双面焊Welding by both side焊接结构Welded construction单道焊Single-pass welding焊道Bead多道焊Multi-pass welding焊层Layer多层焊Multi-layer welding正接(正极性)Straight polarity焊接材料Consumables反接(反极性)Reversed polarity焊条Electrode焊接位置Position of welding焊条药皮Coating平焊Flat position welding酸性焊条Acid electrode横焊Horizontal position welding碱性焊条Basic electrode低氢型焊条Low hydrogen type electrode焊丝盘Wire reel铁粉性焊条Iron power type electrode铜冷却板Cu-cooling plate重力焊条Gravity electrode铜滑块Copper shoe焊剂Flux切割Cutting熔炼焊剂Fused flux焊接工作台Welding bench烧结焊剂Sintered flux焊接变位机Positioner焊丝Wire送丝机构Wire feeder药芯焊剂Flux-cored wire行走机构Traveler保护气体Shielded gas焊接车间Welding shop焊剂垫Flux backing引弧板Run-on tab(end tab)重力焊条Gravity electrode引出板Run-off tab(end tab)焊剂漏斗Flux-hopper定位板Strong-back流量计Flow meter焊接衬垫Welding backing干燥箱Dryer敲渣锤Chipping hammer面罩Helmet条虫状气孔Wormhole焊工手套Welding glove密集气孔Porosity焊钳Electrode holder针尖状气孔Pinhole焊枪Welding gun白点Fish eye(flake)导电嘴Tip切口Kerf喷嘴Nozzle咬边Undercut焊矩Torch焊瘤overlap焊接缺陷Welding defect凹坑Pit未焊透Incomplete penetration烧穿Burn through未熔合Incomplete fusion未满焊Incomplete filled groove渣Slag清根Back chipping夹渣Slag(slag inclusion)清渣Slag removal夹杂物Inclusion焊接烟尘Weld fume气孔Blow hole电光性眼炎Eye-flash焊接性Weldability横裂纹Transverse crack碳当量Carbon equivalent纵裂纹Longitudinal crack未焊满Incomplete filled groove焊趾裂纹Toe crack焊接裂纹Weld crack机械性能试验Mechanical property test热裂纹Hot crack试板Test piece冷裂纹Cold crack试样Specimen氢致裂纹Hydrogen–induced crack侧弯Side bend延迟裂纹Delayed crack弯曲Bending层状撕裂Lemellar tearing横向拉伸Transverse tensile弧坑裂纹Crater crack宏观试样Macro-etching specimen根部裂纹Root crack微观试样Micro-examination specimen再热裂纹Reheat crack破断试验Fracture test热影响区裂纹Heat-effected zone crack抗裂试验Cracking test晶间裂纹Intercystalline crack脆性断裂Brittle fracture塑性断裂Plastic fracture焊接方法Welding process焊接残余裂纹Welding residual stress焊接工艺Welding technology消除应力Stress relieving焊接操作Welding operation焊接变形Welding deformation焊接顺序Welding sequence角变形Angular distortion焊接方向Direction of welding外观检查Visual examination常用缩语无损探伤Non-destruction testing(N.D.T.)气电立焊EGW超声波探伤Ultrasonic inspection药芯电弧焊FCAW射线探伤(X光)Radiographic inspection(X-rayinspection)实心电弧焊GMAW磁粉探险伤Magnetic particle inspection焊剂铜衬垫单面埋弧自动焊FCB渗透探伤Penetrate inspection手工电弧焊SMAW熔池Weld-pool埋弧自动焊SAW焊机(焊接电源)Weld source钨极惰性气体保护电弧焊TIG机舱部分ENGINE ROOM PART熔化极惰性气体保护焊MIG一、机舱设备Machines and equipment in engine room 活性气体保护焊MAG1、主机Main engine手工电弧切割SMAC1)主机油底壳The sump tank of M.E.2)主机飞轮Fly wheel of M.E3)活塞Piston2、发电机Generator engine1)应急发电机Emergency generator engine2)辅机Auxiliary3、锅炉Boiler1)组合锅炉The composite boiler2)锅炉安全阀The safety valve of boiler3)燃烧器Oil burner unit3)主空气瓶Main air reservoir4)水位表Water level gauge4)应急空气瓶Emergency air reservoir5)水位控制器Water level controller5、控制空气瓶Control air reservoir6)过量蒸气调节阀Excess steam pressure control valve6、空气干燥器Air dryer4、舵机7、分油机Oil purifier1)舵机间Steering room1)燃油分油机Fuel oil purifier2)舵机装置Steering-gear2)柴油分油机Diesel oil purifier3)手操舵装置Trick wheel plant3)滑油分油机Lubricate oil purifier4)油缸Oil cylinder4)排渣Sludge discharge5)反馈装置Feedback device8、制淡装置Fresh water generator6)舵Rudder9、焚烧炉Incinerator舵叶Rudder blade10、油水分离器Oil water separator舵杆Rudder stock11、生活污水处理器Sewage treat plant上舵承Rudder carrier12、大气冷凝器Atmosphere condenser热水井Cascade and inspection(hotwell)5)主机燃油供给泵Main engine fuel oil supply pump滑油自清滤器The automatic back-flashlubricating oil filter6)主机燃油增压泵Main engine fuel oil booster pump燃油单元Fuel oil unit7)主机十字头泵Main engine cross head pump1)主机燃油单元Fuel oil unit of M.E8)付机海水泵Generator engine sea water pump2)付机燃油单元Fuel oil unit of A.E9)付机缸套水泵Generator engine cylinder cooling water pump3)粘度计Viscosity controller10)锅炉给水泵Feed water pump of boiler泵Pump11)锅炉燃油泵Fuel oil pump of boiler1)主机滑油泵Main engine lubricating oil pump12)分油机供给泵Fuel oil supply pump of purifier2)主机缸套水泵Main engine cylinder cooling water pump13)制淡海水泵Sea water pump of fresh water generator3)主机缸套水预热泵Main engine cylinder cooling water preheating pump14)压载泵Ballast pump4)主机海水泵Main engine sea water pump15)舱底消防泵Bilge and fire pump17)油渣泵Sludge oil pump2、柴油澄清舱Diesel oil setting tank18)柴油输送泵Diesel oil transport pump3、燃油日用柜Fuel oil daily tank19)燃油油输送泵Fuel oil transport pump4、燃油澄清舱Fuel oil setting tank20)汽缸油输送泵Cylinder oil transport pump5、滑油澄清舱Lubricating oil setting tank 21)淡水输送泵Fresh water transport pump6、滑油储藏舱Lubricating oil store tank 22)热水循环泵Hot water circulating pump7、滑油循环舱Lubricating oil circulating tank 23)饮水日用泵Drinking water pump8、燃油溢油舱Fuel oil overflow tank舱底消防总用泵Bilge,fire and G.S pump9、燃油油渣舱Fuel oil sludge tank喷淋泵Sprinkling pump10燃油深舱Fuel oil deep tank停泊海水泵Harbor sea water pump11滑油污油舱Lubricating dirty oil tank12滑油溢油舱Lubricating oil overflow tank二、各种舱(箱)柜All kinds of tank13滑油油渣打舱Lubricating oil sludge tank1、柴油日用柜Diesel oil daily tank14主机淡水膨胀水箱M.E fresh water expansion tank15付机淡水膨胀水箱A.E fresh water expansion tank16、淡水压力柜Fresh water pressure tank1、滑油系统Lubricating oil piping system17、热水压力柜Hot water pressure tank2、燃油系统Fuel oil piping system18、饮水压力柜Drinking water pressure tank3、海水系统Sea water piping system19、淡水舱Fresh water tank4、缸套水系统Cylinder cooling water piping system20、饮水舱Drinking water tank5、启动空气系统Start air piping system21、锅炉水舱Boiler water tank6、控制空气系统Control air piping system22、分油机工作水箱Purify operating water tank7、排气系统Exhaust piping system23、汽缸油日用柜Cylinder oil daily tank8、日用供水系统Daily water piping system24、尾管滑油重力柜Gravity tank of tube oil9、蒸汽系统Steam piping system25、排气水封箱Exhaust seal water tank10、锅炉给水和凝水系统Feed water and condensate of boiler piping system26、蒸馏水水舱Distilling water tank11、燃油净油系统Fuel oil purified piping system27、污水井Bilge well12、燃油输送系统Fuel oil transport piping system三、各种管系系统All kinds of pipes舵销Rudder pintle13、滑油净油系统Lubricating oil purified piping system舵杆衬套rudder stock liner14、滑油输送系统Lubricating oil transport piping system舵杆轴套Sleeve for rudder stock15、舱底压载系统Ballast and bilge water piping system 舵销承衬套Bush for rudder pintle四、仪表类Instructions舵销轴套Sleeve for rudder pintle1、压力表Pressure gauge上舵承底座Rudder carrier seat2、真空表Vacuum gauge舵销承座Pintle bearing3、温度计Thermometer舵杆承座Rudder stock bearing4、吨位表DWT gauge挡圈Retaining ring5、遥测表Distant survey gauge舵柄Tiller6、液全器Level switch7)舵角The angle of rudder5、空压机Air compressor1)主空压机Emergency air compressor2)应急空压机7、传感器Sensor12、机控室Engine control room五、其它Others13、台虎钳Vise(=vice)1、风机Fan14、表铜截止阀Bronze close valve2、防海生物装置Anti-foul STM plant15、表铜截止止回阀Bronze check valve3、泡沫柜Air foam tank16、铸铁截止阀Cast iron stop valve4、中间轴Middle shaft17、铸铁截止止回阀Cast iron check and stop valve5、尾轴Propeller shaft18、调节阀Adjustable valve6、螺旋桨Propeller19、溢流阀、安全阀Relief valve7、中间轴承Line shaft bearing20、减压阀Reducing valve8、泡沫灭火机Foam fire extinguisher六、材料Material9、饮水消毒装置Sterilizer plant1、管子Pipe10、主配电板Main switch board2、无缝钢管Seamless steel pipe(tube)11、机舱集控台Engine room control console3、紫铜管Purple copper pipe4、铁法兰Iron flange18、支架(马脚)Clamp5、铜法兰Copper flange19、油漆Paint6、盲板法兰Blind-flange20、备件Spare parts7、螺丝(螺栓)Bolt8、双头螺丝Stud七、生产工具Produce tool9、螺帽(螺母)Nut1、图纸Drawing10、不锈钢螺丝Stainless steel bolt2、活络钣Adjustable spanner11、垫片(床)Gasket3、令司板(梅花钣)Ring spanner12、橡皮床Gum gasket4、开口钣Open–ender spanner13、纸箔床Paper copper gasket5、管子钳Pipe wrench14、紫铜床Purple copper gasket6、凿子Chisel15、石墨床Black lead gasket7、锒头Hammer16、青铅床Black lead gasket8、锉刀File17、佛纳Feeler gauge9、螺丝刀Screwdriver10、油漆滚筒Paint roller4、首先请检查安装说明和电气绝缘11、油漆刷子Paint brush Please check the condition of installation and insulationfirst12、钢锯Hacksaw5、我们准备将油水分离器动转13、套筒扳手Socket spanner Now we will run the oily-water separator14、手电筒Torch6、请检查动转情况15、钻头driller Please check the running condition八、英语会话7、接着我们一个一个地做报警/安全保护装置的功能试验1、早上好good morning Now we will do the function test about alarm and safetydevice2、今天我们准备交验油水分离器8、设备交接基本结束Today we will test the oily-water separator.Now the test is over3、请跟我来9、请部有何修改意见?Please fellow me.Do you have any question?10、非常感谢17、这里增加一只落水斗Thanks Add a drain plug here11、再见18、请用空气压缩空气吹干Good bye Please dry it by the compressed air12、请把这对法兰撬紧松开19、我将回车间支拿肥皂水Please tighten/release the flange I will com to my workshop to take some soap water13、这路管子是从发电机单元来的20、这个系统非常重要的,一定要认真检查The piping is from to the G/E unit This system is very important,please check it carefully14、这对法兰/接头在漏21、请交验收整改意见This flange/connection is linking Please check your remarks15、这路系统的试验压力是7公斤22、天太热了,请休息一会The test pressure of the piping system is7bar It’s too hot,please take a rest16、这里请加强please make a clamp here23、我负责这项工作I am in charge of this job电气部分ELECTRIC PART一、常用词汇Words and expression模拟Analog(ue)2182千赫值班接收机2182KHz watch receiver锚灯Anchor lightA异常Abnormal风速风向仪Anemorumbometer应答Acknowledge阳极Anode有功功率Active power天线Antenna执行器Actuator天线馈线连接器Antenna feeder connector调整Adjust天线引入绝缘端子Antenna leading–in insulator空气断路器Air circuit breaker天线共用器Antenna multicoupler报警系统Alarm system天线调谐器Antenna tuner交流电Alternating current电焊机Arc welder电流表ammeter声音的Audible放大器Amplifier自动海图标绘仪Auto chart plotter自动舵Auto pilot自动的Automatic自动雷达标绘仪Automatic radar plotting aid球鼻首警告灯Bulbous bow warning light自动电话Automatic telephone汇流排Bus(-)bar电压自动调节器Automatic voltage regulator汇流排Bus–tie–in自动化系统Automation system蜂鸣器Buzzer压载控制台Ballast control console C、电缆Cable镇流器Ballast电缆填料函Cable gland底座Base敷设电缆Cable laying电池Battery电缆管Cable pipe(conduit)铃Bell电缆扎带Cable strap弯曲Bend电缆托架Cable tray床头灯Berth light校准器Calibrator失电Black out电容capacitor刹车Brake阴板Cathode电刷Brush警告牌Caution plate顶灯Ceiling light通讯Communication中央处理器Central processing unit计算机Computer通道Channel接头Connector充电器Charger恒电流Constant current充放电板Charging&discharging board消耗Consumption海图灯Chart table light触头Contact检查Check接触器Contactor芯片Chip控制箱Control box清洁Clean控制箱Controller雨雪清除器Clear view screen芯线Core二氧化碳释放报警CO2release alarm角灯Corner light同轴电缆Coaxial cable计算器Counter线圈Coil电流Current冷库呼叫Cold store calling D、损坏Damage危险气体报警箱Dangerous gas detecting&alarm box双极单刀开关Double pole single way switch白昼信号灯Daylight signal light双极双刀开关Double pole two way switch 去耦Decoupling set天线收发转换开关Duplexer台灯Desk light值班水手呼叫Duty sailor calling控测器Detector接地Earth拨号Dial接地排Earth bar数字选择呼叫收信机Digital select–call receiver测深仪Echo sounder调光器dimmer电工试验板Electric test panel直流电Direct current电机员Electrical engineer直接起动Direct–on–line starting电极Electrode磁盘Disk应急照明分电箱Emergence lighting distribution box显示Display应急示位标Emergence position indicating radiobeacon遇险信息控制器Distress message controller应急停Emergence stop多普勒记程仪Doppler speed log应急配电板Emergency switch board馈电品Feeder panel机舱报警Engine alarm滤波器Filter集控台Engine control console火警复显器Fire alarm repeater机舱监测报警Engine room monitoring&alarm system防火风闸控制单元Fire damper control unit轮机员呼叫Engineer calling panel火警检测箱Fire detecting box轮机员安全Engineer safety system火焰探头Flame detector增强群呼叫收讯机Enhance group call receiver闪光灯Flash light交换机Exchanger浮充电Float charge防爆灯Explosion proof light强光灯Flood light延伸报警板Extension alarm panel流程图Flow chart故障Failure流量开关Flow switch故障Fault荧光灯Fluorescent light反馈Feed back雾笛Fog horn频率Frequency熔丝Fuse感温探头Heat detector填料Gasket底座Holder通用报警General alarm电笛、喇叭Horn发电机Generator病房呼叫Hospital calling发电机屏Generator panel照明Illumination(铜)锣、钟Gong白炽灯Incandescent light全球卫星定位导航GPS navigator指示器Indicator组合灯板Group alarm light pillar卫星B站INMARSAT B station组合起动屏Group starter panel卫星C站INMARSAT C station电罗经Gyro compass输入输出Input/output卤素灯Halogen light安装Install听筒Handset仪表Instrument硬件Hardware绝缘胶带Insulating tape航向Heading绝缘Insulation接口、界面Interface限位开关Limit switch连锁Interlock连接Link中断Interrupt负载Load逆变器Inverter劳莱收信机Loran receiver接线盒Junction box磁罗经Magnetic compass键盘Keyboard主机电子调速器Main engine electronic governor灯泡Lamp主机功率、纽力仪Main engine power&torque unit液位开关Level switch主机遥控系统Main engine remote control system液位传感器Level transmitter主机转速表Main engine revolution meter灯Light主机安全系统Main engine safety system灯柱Light column主机增压器转速表Main engine turbo-charger speed meter 照明分电箱Light distribution box主配电板Main switchboard避雷针Lighting arrester手动手册Manual标记Mark移动Move桅杆Mast light万用表Multimeter母子钟Master&slave clock铭牌Name plate匹配箱Matching box窄频直接打印机Narrow-band direct printer测量Measure航行灯Navigation light兆欧表Megohmmeter导航系统Navigation system仪表Meter航行监控台Navigation watch console话筒Microphone航行警告收信机NAVTEX receiver镜向灯Mirror light负极Negative监视器Monitor网络Network莫斯键Morse key标称值Nominal value电动机Motor常闭Normally closed塑壳断路器Moulded case circuitbreaker常开Normally open鼠标Mouse失控灯Not under-command light欧姆表Ohm gauge正极Positive欧姆收信机Omega receiver功率、电源Power车钟记录仪Order printer电力分电箱Power distribution box示波器Oscilloscope功率因素Power factor过电流Over current优先卸载Preferential trip过载Overload压力开关Pressure switch巴拿马动河操舵灯Panama canal steering light压力传感器Pressure switch 并联、并车Parallel一次系统Primary system相Phase打印机Printer光敏电阻Photo resister程序Program测速传感器Pick up螺旋桨警告灯Propeller warning light插头Plug广播Public addressor左舷灯Port light脉冲Pulse便携电话Portable telephone按钮Push button雷达Radar电阻Resistance雷达应答器Radar transponder逆功率Reverse power收音机Radio旋转灯Rotating light无线电测向仪Radio direction finder舵角指示器Rudder angle indicator随机存取存储器Radio system运转灯Running lamp额定Random access memory屏幕、屏蔽Screen无功电流Rated power螺丝刀Screwdriver插座Receptacle搜索灯Search light录音机、记录仪Recorder二次系统Secondary system整流器Rectifier串联Series继电器Relay屏蔽Shield复位Reset船名灯Ship name light岸电箱Shore connection box短路Short circuit展示、给-----看Show电磁阀Solenoid valve分励脱扣Shunt trip消音Sound off停车Shut down声力电话Sound power telephone签字Sign空间加热器Space heater信号集合箱Signal acquisition unit扳手Spanner信号灯Signal light喇叭Speaker单边带收发机Single side band transceiver分配器Distributor电笛Siren右舷灯Starboard light慢车Slow down起动Start烟气探测报警箱Smoke detecting&alarm box起动带Start感烟探头Smoke detector尾灯Stern light插座Socket停止Stop软件Software苏伊士运河尾灯Suez canal stern light电烙铁Soldering iron支撑物supporter开关Switch验电笔Test pen打开Switch on试验程序Test procedure关闭Switch off热敏电阻Thermistor同步屏Synchronizing panel热电偶Thermocouple同步表Synchronoscope温度计Thermometer转速表Tachometer恒温计Thermostat录音机Tape recorder触摸屏Touch panel车钟Telegraph轨迹球Trackball电视Television收发机Transceiver温度开关Temperature switch传感器Transmitter温度传感器Temperature transmitter变压器Transformer接线柱Terminal脱扣Trip接线排Terminal board欠电压Under voltage试验Test不中断电源Uninterrupted power source卸载Unload二、会话Dialog and conversation超高频VHF telephone船东o-owner视觉的Visual验船师s-survey电压Voltage检验员q-quality inspector电压表Voltmeter电工e-electrician壁灯Wall light1、检验电缆敷设瓦特Watt Inspection cable laying波道Waveguide你能带我去看机舱电缆敷设气象传真收信机Weather fax receiver Q:could you show me cable laying of engine room?驾控台Wheel speed&directionindicator好,走吧。

最全轮机英语基本单词

最全轮机英语基本单词

yacht : [jɔt]n.快艇,(竞赛用的)帆船,游艇general cargo ship: 杂货船refrigerator ship :冷藏船cruiser n.游船dry bulk carrier 干散货船passenger liner 旅客班轮cruiser n.游船air cushion craft 气垫船barge-carrier 载驳货船bulk-carrier散货船catamaran 双体船container ship 集装箱船chemical carrier 化学品(运输船)diesel boa柴油机船dry cargo ship 干货船electric motor ship 电动机船ferry 渡船freighter (cargo ship) 货船fire boat 消防船hydrofoil craft水翼船Ice-breaker破冰船life boat 救生船LNG carrier(liquefied natural gas carrier)液化天然气(运输)船multi-purpose ship多用途船oil barge 油驳ore carrier(ore ship )矿砂船passenger liner 定期客船pilot boat引航船roll - on / roll - off ship (Ro-Ro ship) 滚装船reefer ( refrigerator ship )冷藏船salvage vessel救助船scientific surveying ship科研考察船semi-container ship半集装箱船semisubmersible drilling vessel半潜式钻井船specialized duty vessel专业船tramp不定期货轮tug拖船10.商船:merchant ship11.油船:tanker 12.散货船:bulk carrier2.船舶主要部分船首:bow 船尾stern 左舷:port side 右舷:starboard side 艏楼:forecastle艉楼:poop 上层建筑:superstructure肋骨:frame二层甲板:tween deck机舱:engine room 水密分舱:watertight compartment 艏尖舱:fore peak tank艉尖舱:after peak tank 双层底舱:double bottom tank 制链器:chain stopper锚链舱:chain locker锚链管:chain pipe锚机滚筒:chain cable barrel锚链筒:hawse pipe标准罗经:standard compass磁罗经:magnetic compass主操舵罗经:main rudder compass 陀螺罗经:gyrocompass推进器:propeller3.船用柴油机工作原理1.船用柴油机:marine diesel2.内燃机:internal combustion engine3.气缸:cylinder 4.活塞:piston 5.细雾状燃油:fine spray of fuel6.曲轴:crankshaft7.推进器:propeller 8.循环:cycle 9.四冲程柴油机:four-stroke diesel10.进气:fresh air11.压缩:compession 12.膨胀:expansion13.排气:exhaust14.二冲程柴油机:two-stroke diesel17.下死点:B.D.C15.燃烧室:combustion chamber 16.工作原理:principle of operation 18.排气口:exhaust port 19.残留废气:residual exhaust 20.上死点:T.D.C21.燃油喷射:fuel injection 22.进气口:inlet port 23.工作冲程:working stroke24.减速齿轮箱:reduction gearbox25.交流发电机:alternator26.连杆:connecting rod 27.扫气口:scanvenging port4.船用柴油机的种类1.船用发动机:Marine engine2.紧凑:compact3.柴油机:diesel4.蒸汽机:steam turbine 5.气轮机:gas turbine6.内燃机:internal combustion engine7.输出功率:output power 8.制动马力:brake horsepower9.螺旋桨:propeller 13.燃油消耗率:fuel comsuption 14.锅炉:boiler15.有吸引力的:attractive16.集装箱船:container ship17.衰变:decay 18.通过比较:by comparision19.限制,约束:restriction20.叶片:blade21.有效马力:effective horsepower22.放射性的:radioactive23.船用核装置:marine nuclear plant24.货油泵:cargo oil pump固定件:fixed part 运动件:moving part 曲柄箱:crankcase缸套和衬套:cylinder and liner 气缸盖:cylinder cover 活塞:pistion气缸体:cylinder block 活塞头:piston crown 活塞杆:piston rod十字头:cross 连杆:connecting rod 主轴承:main bearing轴向推力:axial push端塞螺栓:side-chock bolt 从动轴:driven shaft 推力块:thrust block扫气箱:scavenging air box机座:bedplate 机架:frame冷却水套:cooling jacket 21.燃烧室:combustion chamber22.排气阀:exhaust valve23.燃油阀:fuel valve 24.起动阀:starting valve25.安全阀:safety valve26.示功器旋塞:indicator cock 27.冷却腔:cooling chamber28.活塞裙:piston skirt29.活塞环:piston ring30.垫圈:rubber ring31.往复运动:reciprocating movement 32.工作行程:power stroke6.燃油系统燃油系统:fuel oil system 运行和维护:operation and maintainence残碳值:carbon residues 燃油粘度:fuel oil's viscosity十六烷值:cetane number 热值:calorific value 闪点:flash point凝固点:setting point 比重:gravity 10.含水量:water content11.机械杂度:mechanical impurity12.重油:heavy fuel 13.渣油:residual oil14.沉淀柜:settling tank15.燃油舱:bunker tank16.日用柜:daily service tank17.细滤器:fine filter18.压力调节阀:pressure regulating valve19.针阀:needle vavle20.低油位报警:low tank level level alarm21.输送泵:transfer pump22.三通阀:three-way valve23.喷射泵:injection pump 24.过滤器:stainer7.润滑系统润滑油膜:lubricating oil film 运动件:moving part 运动条件:operation conditions油冷式活塞:oil cooled piston抗氧化:resistance to oxidation总量损耗系统:total loss system feeding循环式系统:circulating system传动装置:running gear燃烧室:combustion space活塞顶:piston crown活塞环:piston ring衬套壁:liner wall运动方向的改变:reversal of direction of motion机械注油器:mechanical lubricator曲轴箱:crankcase轴承:bearing17.活塞杆:piston rod 18.辅助设备:auxiliary equipment 19.泵:pump20.离心分离机:centrifuge8.水冷却系统燃油喷射阀fuel injector valve排气阀exhaust valve起动空气阀starting air valve机械强度mechanical strength内部管道internal passage热交换器heat exchanger气缸套冷却水循环泵cylinder liner circulating pump涡轮增压器turbo-blower闭式系统closed system开式系统open system压力水柜pressure tank海水循环式冷却器sea water circulated cooler heat exchanger汽蚀效应cavitation effect气囊steam pocket放气口air lock透气管ventilation pipe支路branch可视式流量计visual flowmeter喷嘴积碳nozzle deposited carbon滑油冷却器lubricating oil cooler盲板法兰blind-flange9.舱底和压载系统舱底水:bilge water 压载水:ballast water 相互连接:interconnec t涨水,进水:flood 在船外,到舷外:overboard 水密舱室:watertight compartment应急舱底水泵:emergency bilge pump 替换物,选择对象:alternative引水装置:priming device 到某种程度:to some extent 调节船舶吃水差:trim the vessel 切换阀箱:change-over chest10.管路系统发证机构:certifying authority铸铁:cast iron冲击载荷:shock loading易碎性:brittle nature 循环热处理:cyclic heat treatment低碳钢:mild steel气密结构:gastight structure热膨胀:thermal expansion 锅炉水舱柜:boiler feed water tank贯通配件:through fitting隔离空舱:cofferdam船体变形:deflection of ship construction1.safety valve(安全阀)2.steam stop valve(蒸汽截止阀)3.starting valve(起动阀)4.indicator cock(示功阀,示功考克)5.governing valve(调速阀)6.by-pass valve(旁通阀)7.main stop valve(主截止阀)8.hull valve(船体阀)9.flushing valve(冲洗阀)10.vent valve(排气阀)11.suction valve(进气阀)12.angle valve(角阀)13.automatic valve(自动阀)14.pressure valve(压力阀)15.quick-closing valve(速闭阀)16.self-closing valve(自闭阀)17.air filter(空气过滤器)18.coarse filter(粗滤器)19.fine filter(细滤器)20.heating circulating valve(加热循环阀)11.船用泵容积式泵:displacement pump 离心泵:centrifugal pump往复泵:reciprocating pump叶片泵:vane pump齿轮泵:gear pump旋转泵:rotary pump离心力:centrifugal force轴向的:axial flow涡轮,涡轮机:turbine自吸式:self-priming啮合齿轮:meshing gear蒸汽喷射器:steam ejector舵机液压系统:steering gear hydraulic system人字齿:double helical tooth大气压:atmospheric pressure立式泵:vertical pump12.舵机舵机:steering gear船级社:classification society转舵能力:steering capacity舵叶:rudder船舶吃水:ship’s draught驾驶台:bridge故障:trouble独立的:independent液压伺服马达:hydraulic telemotor舵机室:steering gear room舵柱:rudder stock液压油缸:hydraulic cylinder液压泵:hydraulic pump撞杆:ram舵角信号:signal of rudder angle13.甲板机械甲板机械:deck machinery克令吊:crane日常检验:routine checking锚泊设备:anchor arrangement 集装箱吊装设备厂:container handling facility原动机:prime mover装卸能力:handling capacity多旋转吊杆系统:multiwinch slewing derrick system安全工作负载:safe working load绞车卷筒:winch barrel or drum吊杆式起货装置:derrick crane system14.推进装置直接传动:direct drive推进效率:propulsion efficiency轴系:shaft system旋转方向:rotating direction齿轮传动:gear drive减速齿轮箱:reduction gear box减速装置:reduction arrangement双桨:twin-screw双舵:twin-rudde r双机并车:twin-engine incorporation多级:multi-stage带倒车离合器的减速:reduction with an astern clutch机舱:engine space挠性联轴节:flexible coupling安装误差:installation error可调螺旋桨:VPP or CPP固定螺旋桨:fixed pitch propeller定位:keep station15.轴系及设计程序传动轴系:transimission shafting system艉轴:stern shaft螺旋桨轴:screw shaft中间轴:intermediate shaft法兰联轴节:flange coupling可拆联轴节:removable coupling 隔舱填料函:compartment stuffing box推力环:thrust ring中空轴:hollow shaft轴倾斜度:shaft rake动态特性:dynamic characteristic扭振:torsional vibration纵振:longitudinal vibration回转振动:whirling vibration振动计算:vibration calculation 螺旋桨桨叶:propeller blade16.船舶设计与造船工程师造船工程师:naval architect造船工程学:naval architecture力矩平衡:moment balance重力平衡:weight balance轴马力:shaft horsepower净登记吨位:net register tonnage总吨位:gross tonnage扣除空间:deductible space流体力学:fluid mechanics结构强度:structural strength重货:high-density cargo轻货:low-density cargo港口税:harbor due母型船:projected ship重心:centers of gravity纵倾和稳性:trim and stability肋骨尺度:frame dimension外板厚度:plate thickness零件图:detail drawing总图:general drawing17.造船过程1.(船舶)下水滑道:launching way2.初步设计:preliminary design3.合同设计:contract design 4.详细设计:detail design5.运作要求:operational requirement6.缩尺船模(模型):scale model7.成组建造技术:group technology to shipbuilding 8.大规模生产:mass production 9.任务系统:mission system10.交船日:delivery date 11.性能要求:performance requirements12.计划与调度:planning and scheduling13.个别零件:individual parts14.干船坞:dry dock15.投标过程:bidding process 16.船体分段:hull block17.装配线:assembly line18.概念设计:concept design18.船厂设施building period建造周期assembly line 装配(流水)线sloping shipway 有坡度船台,滑道building basin 船台floating dry dock 浮船坞engineering workshop轮机车间erection shop 装配车间fitting out quay舾装码头pumping station泵站,动力室repair quay 修船码头ship drawing office 船舶设计室20.船舶下水与舾装横向下水:sideway launching下水架:launching cradle滑道:standing way滑板:sliding way边墩:side support下水扳机:launching trigger局部压力:local pressure限制水域:restricted waterway减速力:retarding force阻力锚:drags21.适航1.试验大纲:sea trial programmers2.测速区:measured mile course3.重新试航:re-trial run4.性能试验:performance test5.动力装置:power plant6.抛锚试验:anchor-heaving trial7.适航性能:sea-keeping performance8.回转试验:turning trial9.潮汐效应:tidal effect10.逐级加速试航:Progressive speed trial11.续航力试验:endurance trial12.船舶试验协议:Protocol of T rials of the ship13.船舶设备清单:Inventory of the equipment of the vessel14.消耗品储备协议:Protocol of Stores of Consumable Nature15.完工图:finished drawings and plans16.交船:delivery of the vessel23.船级社1.合同前服务:pre-contract service2.提交检验申请:submit survey application3.申请评审及签署检验服务协议:aplication reviewing & survey agreement4.船舶审图及确定船用产品持证清单:drawing approval & required marine products list舶开工前检查:inspect before steel-cutting6.焊接工艺认可:welding technology approval7.焊工资格:welder qualification8.建造检验标准:standard of construct survey9.分段检验:structure inspection10.结构装配及焊接:structure assemble & welding11.安装主辅机、舵及轴系:installation of main engine, auxiliary mechinery & shafting 12.船台上或船坞内装配检验:assemble inspection on slipway or dock13.分段合拢检验:inspection of structure assemble14.焊缝检验:inspection of welding 15.无损探伤检验:NDT16.密性试验:tightness test17.船舶下水:lauching18.系泊试验:mooring trial19.航海试验:sea trial20.签发短期证书:issuance of interim certificates21.签发全期法定证书:Issuance of Full-Term Statutory Certificates22.CCS船舶录:Register of Ships by CCS23.签发全期船级证书:Issuance of Full-Term Class Certificates24.船级委员会:Class Committee。

船舶常用英语(一)汇总

船舶常用英语(一)汇总

一、船舶类型常用英语ship, vessel 船,船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船;商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船;推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线,中线athwartships 横对船体(与船首尾线直交)bevel 斜角;斜面base line 基线amidships 在船中部;在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点;交叉;横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度(宽度、深度)freeboard 干舷rise of floor (dead; rise) 舭高;船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel (首尾)等吃水,平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室;旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后(部船)体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage (船体水线下的)附体;附件auxiliary machinery 辅助机械;辅机balanced rudder 平衡舵ballast 压载(物)ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱(水)batten 板条;压条(封仓用)batten-ceiling (货舱内)护舱条,护板beam 横梁beam bracket 梁肘板bearding 交合线,榫(艏柱或艉柱上)bending moment 弯矩bilge 舭部;舱底;(船底)污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩;系船柱;双系柱bolster 枕垫bonnet 烟囱帽;机罩boom 杆;吊杆;桁;叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部;轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首,船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板;(三角)拖架breakwater 挡浪板bridge 桥;桥楼;驾驶台bulb angle 圆头角材bulbous bow 球形船首,球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接;残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘;绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯,舷门cat walk (油轮上的)天桥,步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器;垫木clamp plate 夹板,压板cleat 羊角;系绳铁栓;防滑条coaming 围板;舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁;防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱;槽形;波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口;切davit 吊艇架;吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱(物料);衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk (船内)应急通道engine bed 机座engine casing 机舱围壁escape scuttle (船内)应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) (油船)膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫;护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank (船的)首舱;前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔;放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈,垫料(集)密封垫general service pipe (G.S pump) 通用泵,总用泵girder 桁材gooseneck(parity iron) 鹅颈头;吊杆弯头grating 格子板;滑铁板ground tackle 锚泊索具gunwale 舷缘;舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜(甲板下)gusset 角板;扣板gutter (甲板)水沟;槽沟gutter angle; waterway angle (舷侧)排水沟角钢gypsy 绞筒(锚机绞车上的)handrail 舷墙扶手hanging rudder; hinged rudder 吊舵;悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索;大缆heel 踵材;横倾hinged cover(door) 铰链盖(门)hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗;开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材(防挠材)hull 船壳,船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板;衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯;绳梯Joggled joint 折接;弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线;艏艉线keel plate 龙骨板keel rail (救生艇)艇底把手keelson 内龙骨kingpost 起重柱;将军柱knee 肘板;弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨;纵材;纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱;岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口;槽口;刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱;墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼;船尾poop deck 艉楼甲板port 舷门;舱门;(装货)口;窗;门;孔porthole 舷窗;(装货)舷门propeller; propellor 推进器;螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking (船体)横向挠度rail 扶手;栏杆rolling 横摇round of beam 梁拱round stern 圆(船)尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针;舵栓rudder plate; rudder blade 舵叶;舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁;舵杆管rung (梯子)踏步;横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处;斜面;斜接scarf joint 斜(嵌)接scarf weld (斜面)焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗;人孔(盖);小舱口盖seam 焊缝;接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧;地轴弄shedder plate 泄板;斜板sheer 舷弧;偏航sheer strake 舷顶列板shell 船壳;壳shell frame 舷侧肋骨shell plating 船壳板;外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板(散装谷类);防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木;垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽;开缝sluice 水密门;水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管;测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架;台架;脚手架stanchion 支柱;栏杆柱static load 静载荷stay 支柱;撑条;支索stay bar(or rod) 撑杆stay plate 撑板stem 艏;艏柱;艏材stem post 艏柱stern 船尾,艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材;扶强材;加固物stool 托架,座,凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box (舱底水)过滤箱strut 撑材,支柱,轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布,帆布,舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板,牵板,连接板topside tank 顶边舱;上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁,横材transverse bulkhead 横舱壁transverse frame 横肋骨,横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧,隧道,风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管(孔)ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上(下)支架板upper (lower) stool 上(下)托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁,挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁,桁板横梁web frame 加强肋骨,框架肋骨,桁板肋骨web plate 腹板wedge 楔木,楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱,翼柜wire clip 钢缆夹wire reel 卷缆车,钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转;扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性,可塑(锻)性flexibility 挠性,柔性,易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性,稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化,淬火tempering 回火casting 铸件,铸造forging 锻件,锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层,表面处理coating 涂层,敷料corrosion 腐蚀,侵蚀wastage 损耗,蚀耗wear and tear 蚀损,磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀,锈斑indent 凹痕,凹陷groove 槽沟detachment 脱开,脱焊rupture 断裂,破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准,校直snip 剪断,剪片taper 削斜,斜度B.Shipbuilding workmanship (造船工艺)Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard pro 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊;断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊;长孔焊plug weld 塞焊;圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut (焊接)咬边;根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability(curve)动稳性(曲线)entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩(应力)hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting (波浪对船体的)冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩(应力)seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头(力)statical stability (curve) 静稳性(曲线)surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头(力)transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横(纵)稳心transverse (longitudinal) stability 横(纵)稳性trim by the bow (stern) 首(尾)倾turning quality (circle) 回转性(圈)velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳,情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热(或电气绝缘)9.not properly adjusted 未经正常校正10.defective 有缺陷的(失效)11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作(作用),不是指故障14.in disorder 零乱(船属具零乱了)15.not working 不能工作16.inoperative 不能工作(失效)unworkable, inoperable 指本身不能工作,在损坏状况判断中不能使用17.out of function 不能工作,失去作用,不起作用18.unserviceable (useless) 不能使用(指必须换新的损坏部件)19.could not be started(failed to start) 不能启动20.empty 空的21.fitted incorrectly 安装不正确(指小型的装置设备)installed incorrectly 安装不正确(指较大的装置设备)22.dangerous accumulation of inflammablevapors 可燃气体危险集积it was obvious that this state had existed for a considerable time (损坏)状况是长期存在的23.sluggish in (action, answering) (动作、应答)迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全,不完整5.deficient 不足,缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏,省去9.removed 移开,拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用(尺寸,材料,仪器)C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性(比5好)7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛(仅从反光上可观察到)2.chafed 擦痕3.scored 拉痕(痕较chafed深)4.scratched 抓痕(硬拉过的痕)5.scraped 刮痕(长期运行刮的痕)6.grooved 槽痕(比pitting深)7.ridged 凸起雷治痕(环状的痕)8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂,折裂10.fractured 折裂11.broken off 破掉(破裂后跌落)broken 破裂,破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起,翘曲19.indented (dented) 凹痕,凹陷(指船壳板在两档肋位间的凹陷)20.set in 凹陷(指船壳板较大面积的凹陷)21.waved 波曲22.curled 卷曲(指绳索)23.rumpled 褶皱(指垫片)24.bulged 鼓起,凸出25.collapsed 倾陷,倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮(油漆剥落)30.burst 爆破(指高压管路)31.blown off (packing) 吹脱32.distorted 扭曲,歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten (木、橡胶)腐烂、腐坏9.decayed (电缆)腐烂、腐坏10. aerated(橡胶、电缆)腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck (粘)咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞(常指管子的堵塞)18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住,阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting (铆钉)松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted (轴线弯曲并扭转)扭曲10.sprung (铆钉)扭歪11.twisted (轴线未弯、纯扭转)扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗,磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged(电)完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换(管、板、栏杆)5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸(某一零件)13.disassembled 拆散(解体)14.stripped 拆除(某一部件)15.unshipped 拆下16.disconnected 断开(线、管接头)17.opened 打开18.lifted 抬升、举起19.jacked 顶起(用千斤顶顶起)20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合(装配好)5.run to fit 跑合(运动磨合)6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金(专指巴氏合金)3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整,校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷(除锈)10.chipped & scraped 拷锈(油漆)11.measured & recorded 测量并记录12.logged (hourly) 记录(小时)D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds (面积、深度、高度较大)焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊。

船舶专业英文词汇汇总

船舶专业英文词汇汇总

船舶专业英文词汇船舶专业英语词汇(按照字母顺序排列)(一)a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住(舱室)accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼,翼剖面,机面,方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨,方龙骨,矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条,板条beam 船宽,梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭,舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓,上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽,计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼,驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏,球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例,按约定船舶专业英语词汇(按照字母顺序排列)(二)cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容,载货容积cargo handling 货物装卸carriage 拖车,拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心,重心,质心,矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭,舷,脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室,粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀,腐蚀couple 力矩,力偶crane 克令吊,起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据,准则Critical ath Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室,甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机,吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图,原理图,设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站,划分,分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力,拖拽力drainage 排水draught 吃水,草图,设计图,牵引力dredge 挖泥船drift 漂移,偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计,功率计船舶专业英语词汇(按照字母顺序排列)(三)e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力,供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度,高程,船型线图的侧面图,立视图,纵剖线图,海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力,全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配,安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮,渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边,法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘,外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型,流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件,锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨,框架,桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁,桁架girder of foundation 基座纵桁governmental authorities 政府当局,管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书,19世纪英国另一船级社的船名录,现合并与劳埃德船级社,用于登录快速远洋船gross ton 长吨(1.016公吨)group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇(按照字母顺序排列)(四)half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的,螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂,轴毂,套筒hull form 船型,船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖,通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水,浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的,加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点,交*,横断(切)inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射,下水launch 汽艇launching equipmeng (向水中)投放设备LCC 大型原油轮leading edge 导缘,导边ledge 副梁材length overall 总长leveler 调平器,矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约,规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵(横)稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械(主机)卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的,海运的,靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单,物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇(按照字母顺序排列)(五)N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机,准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴,中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的,正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽,开凹口oar 橹,桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构,抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱,垂直的,正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销,枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头,停泊所quotation 报价单船舶专业英语词汇(按照字母顺序排列)(六)racking 倾斜,变形,船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register (船舶)登录簿,船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂,恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接,铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺,尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面,横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切,剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨,导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt (气垫船)围裙slamming 砰击sleeve 套管,套筒,套环slewing hydraulic motor 回转液压马达slice 一部分,薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置,舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道,尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲,加强stiffener 扶强材,加劲杆straddle 跨立,外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱,支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人,总段长,车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖,越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇(按照字母顺序排列)(七)tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的,正切的tangential viscous force 切向粘性力tanker 油船tee T型构件,三通管tender 交通小艇tensile stress 拉(张)应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器,助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home (船侧)内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter (海运)保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶(摆线)推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流,尾流water jet 喷水(推进)管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器,消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨(游艇)working allowance 有效使用修正量worm gear 蜗轮,蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇。

修船英语词汇(已排版)

修船英语词汇(已排版)

一、船体结构词汇AAccommodation 居住舱室Aft perpendicular 艉垂线Aft peak tank 艉尖舱Aft peak bulkhead 艉尖舱壁Air diffuser 空气扩散器Air hole 通风孔Air intake 进气口Aircraft carrier 航空母舰Airdrivenwater pump 气动水泵Anchor 锚Anchor arm 锚臂Anchor chain 锚链Anchor crown 锚冠Anchor fluke 锚爪Anchor link 链环Anchor mouth 锚唇Anchor recess 锚穴Anchor shackle 锚卸扣Anchor stock 锚杆Angle bar 角钢Angled deck 斜角甲板Antenna 天线Antirollingtank 减摇水舱Automatic sprinkler 自动喷水器Automatic ventilator 自动通风筒Auxiliary engine seating 辅机机座Auxiliary tank 调节水舱Back of blade 叶背Baffle 挡板,隔板Baggage room 行李舱Balance weight 平衡锤Balanced rudder 平衡舵Ball bearing 滚珠轴承、球型布司Ball valve 球阀Ballast tank 压载舱Barrel 圆筒Base block 垫块Batten 长行护板Beam 横梁Beam knee 横梁肘板Beam bracket 横梁肘板Bearing 轴承Bearing seat 轴承座Bedplategirder 基座纵桁Bellmouthof hawspipe 锚链筒喇叭口Berth 软垫床Bicoloredlight 两色灯Bilge bracket 舭肘板Bilge keel 舭龙骨Bilge plating 舭肘板Bilge sounding pipe 舭部边舱水深探管Bilge strake 舭列板Bitt 单柱系缆桩Bitts 双柱系缆桩Blade (螺旋桨)浆叶精品文库欢迎下载- 2 -Blade root 叶根 Blade tip 叶梢 Blockage 堵塞 Boat davit 吊艇架 Boat deck 艇甲板 Boat fall 吊艇索Boat hook 艇吊钩,(舢板)挽钩 Boatswain ’s store room 帆缆库 Bobstay 首斜桅拉索 Boiler 锅炉Boiler bearer 锅炉基座 Bollard 系缆桩 Bolt 螺栓Bolt lock 插销锁 Book case 书柜Boss (螺旋桨)轴毂 Bossing 轴包架,轴毂 Bosun store 帆缆库Bottom ceiling 舱底铺板 Bottom center girder 中底桁 Bottom frame 船底肋骨 Bottom grating 船底垫板 Bottom plate 船底板Bottom side girder 旁底桁 Bottom side tank 边底桁 Bottom transverse 底边舱 Buoy tender 航标船Bow door 艏门(滚装船) Bowsprit (帆船)艏斜桅 Bow structure 艏端结构Bow thruster 艏侧推 Bower anchor 艏锚 Box keel 箱型龙骨 Brace 转帆索Bracket 肘板,三角板 Bracket floor 框架肋板 Brake 制动装置,刹车Brake band (lining ) 制动带,刹车带 Brake crank arm 制动曲柄Brake hydraulic cylinder 制动液压缸 Brake drum 刹车卷筒Brake hydraulic pipe 刹车液压管 Breast hook 艏肘板 Breadth 船宽Bridge 桥楼,驾驶台Bridge console stand 驾驶室集中控制台 Buffer spring 缓冲弹簧 Bulb plate 球扁钢 Bulbous bow 球鼻艏Bulk cargo carrier 散货船 Bulkhead 舱壁Bulkhead deck 舱壁甲板 Bulwark 舷墙Bulwark plate 舷墙板 Bulwark stay 舷墙支撑 Buoyant box 浮箱 Buoy 浮筒Buoyancy tank 浮力舱Butterfly screw cap 蝶形螺帽 C精品文库欢迎下载- 3 -Cable 电缆、缆索 Cable chock 导缆钳 Cable drum 缆索卷筒 Cable releaser 弃链器 Cable winch 钢索绞车 Cage 起货机操作室 Camber 梁拱Cant beam 斜横梁 Cant frame 斜肋骨Cantilever beam 悬臂梁 Captain 船长Captain room 船长室 Cargo 货物Cargo battens 货物护板条 Cargo block 吊货滑车 Cargo boom 吊杆Cargo chain 吊货短链Cargo fall ,cargo runner 吊货索 Cargo hatch 货舱口 Cargo hook 吊钩Cargo hook shackle 吊货钩卸扣 Cargo hook swivel 吊钩转环 Cargo hose 货油软管Cargo runner lead block 吊货索导向滑轮 Cargo winch 起货绞车Cast steel stem post 铸钢艏柱 Cat walk 步桥(油船),栈道 Catamaran 高速双体船 Ceiling 室顶板 Ceiling lamp 吊灯Cement 水泥Cement draining 水泥流水沟 Center girder 中纵桁 Center keelson 中内龙骨Centerline bulkhead 中纵舱壁 Chock 导缆钳Circular mooring pipe 圆形导缆孔 Chain axle 链轮轴 Chain clamp 制链钳Chain cable fairlead 导链滚轮 Chain cable stopper 制链器 Chain controller 制链器 Chain link 锚链环 Chain locker 锚链舱 Chain wheel 链轮Chain wheel shaft 链轮轴 Chart 海图Chart light 海图灯 Chart room 海图室 Chart table 海图桌Chief engineer ’s room 轮机长室 Clear view screen 旋回视窗 Clearance hole 通焊孔 Cleat 系缆扣Cleat post 羊角系缆桩 Clip 夹扣Clipper bow 飞剪型船首Closed mooring chock 闭室导缆钳 Clutch 离合器Clutch hand wheel 离合器手轮精品文库欢迎下载- 4 -CO2 fire extinguisher 二氧化碳灭火器 Coat and hat hook 衣帽钩 Cofferdam 空隔舱Collision bulkhead 防撞舱壁 Column 立柱Common link 普通链环Communicating pipe 连通管 Communicating tank 连通水柜 Commuter 交通船 Compass 罗经Compass deck 罗经甲板Compressed air bottle 压缩空气瓶 Condenser 冷凝器 Conductor tube 导管Connecting tank 连接水柜 Connecting traverse 吊钩梁 Container 集装箱Container ship (liner,vessel ) 集装箱船 Control desk 操纵台Control console of main engine 轮机控制台 Control valve 控制阀 Cork 软木、软塞Corrugated bulkhead 槽型舱壁 Coupling 接头(考贝令) Cover plate 盖板Cowl head ventilator 头颈型通风筒 Cushion 软垫Crane 克令吊、起重机 Crank 曲柄 Crew 船员Crew ’s bed room 普通船员寝室 Crow ’s nest 桅杆了望台 Crew ’s quarters 船员居住室 Crew ’s W.C 船员厕所 Crosshead 十字头Cruciform bitts 双十字系缆桩Cruciform post bollard 单十字系缆桩 Cruiser 巡洋舰Cruiser stern 巡洋舰式船尾 Cup and ball joint 球窝关节 Curtain 窗帘Cycloidal propeller 直叶推进器 Cylinder 缸体、圆柱体 DDamper 缓冲器Davit arm 吊臂(吊艇架) Davit hook 吊艇钩 Day room 起居室Deadlight (舷窗灯)风暴盖 Deck centerline 甲板中心线 Deck framing 甲板骨架Deck flange of hawse pipe 甲板锚链孔凸缘 Deck girder 甲板纵桁 Deck house 甲板室Deck longitudinal 甲板纵骨 Deck side line 甲板边线 Deck stringer 甲板边板Deck transverse 强横梁(纵骨架式结构) Deep sea vehicle 深潜器; Deep tank 深舱精品文库欢迎下载- 5 -Detent (stopper ) 棘爪、制链器 Derrick 起重机、吊杆 Derrick boom 吊杆 Derrick fall 吊杆索 Derrick post 吊杆柱 Derrick rig 吊杆装置 Desk lamp 台灯 Destroyer 驱逐舰Detachable shackle 散合式连接卸扣 Devil ’s claw 链式制链器Diagonal stiffener 斜置加强筋 Diesel engine 柴油机Direction finder 方位测定器Direction finder antenna 测向仪天线 Dispensary 医务室 Displacement 排水量Displacement type vessel 排水型船 Distance line 张索 Dock 船坞Domed bulkhead 球型舱壁 Door curtain 门帘 Door frame 门框 Door handle 门把 Door hook 门钩 Door plate 门板 Doorway 出入门Double bottom 双层底Double bottom tank 双层底舱 Double hook 山字钩Double roller chock 双滚轮式导缆钳Doubling plate 复合板,加强板 Down halyard 降帆索 Draft 吃水Draft line 吃水线 Draft mark 水尺 Dragline 拉索Drain hole 流水孔\污水孔 Drain well 污水井 Drawer 抽屉Drawer handle 抽屉把手 Dredger 挖泥船 Drillship 钻井船Driving shaft system 传动轴系 Drum 卷筒Drum flange 卷筒凸缘 Dry cell 干电池Dry power container 干粉容器Dry power fire extinguisher 干粉灭火器 Drying agent 干燥剂Dynamic supported craft 动力支撑型船 EEccentric wheel 偏心轮Eccentric roller jacking device 偏心起升滚轮装置 Echosounder 回声测深仪器Electric motor 电动机\电马达 Electric rudder gear 电动舵机Electric revolving crane 电动回转式起重机 Electric motor windlass 电动锚机Elevating system ,elevator 升降机装置精品文库欢迎下载- 6 -Elliptical mooring pipe 椭圆型导缆孔 Elliptical stern 椭圆型船尾 Embarkation deck 登乘甲板 Emergency exit 紧急出口Enclosed lifeboat 封闭式救生艇 End open link 末_______端链环 End shackle 末端卸扣 Engine 主机\发动机Engine air inlet 发动机进气口 Engine casing 机舱棚 Engine foundation 机座 Engine room 机舱Engine room opening 机舱口 Engine room frame 机舱肋骨Engine room hatch end beam 机舱口端梁 Engine room hatch girder 机舱口纵桁 Engine telegraph 车钟 Enlarged link 加大链环Enter guider (集装箱阁栅)入口导承 Exhaust pipe (发动机)排气口 Exhaust valve 排气阀Expanded bracket 延伸肘板Expansion joint 伸缩接头\波纹管 Expansion trunk 膨胀井 Eye plate 眼板 FFace plate 面板 Fairlead 导缆器 Fan 鼓风机Fan vent 鼓风机排气口Fast craft 高速船舶 Fender 护舷材 Ferry 轮渡 Filter 过滤器 Fin 鳍\散热片Fin angle feedback set 鳍角反馈装置 Fin box 鳍箱 Fin shaft 鳍轴Fin stabilizer 减摇鳍Fire boat (fire fighting ship ) 消防船 Fire extinguishing agent 灭火剂 Fire fighting gun 消防枪 Fire hose 消防水管Fire hydrant (fire plug ) 消防栓Fixed water fire extinguisher 固定式水灭火器 Flange (flange edge ) 折边\法兰 Flap 折板(滚装船首尾跳板) Flaptyperudder 襟翼舵Flat steel plate 扁钢 Floating crane 浮吊 Floating dock 浮船坞 Flume tank 槽形水舱 Flush valve 冲水阀 Fly net 纱窗Flying passage 步桥(油船)Foam concentrate container 泡沫液容器 Folding hatch cover 折叠式舱盖 Foot brake 脚踏刹车 Foot ring 地令精品文库欢迎下载- 7 -Footrope 根缆Fore and aft stay 前后拉索 Fore lower topsail 前下中桅帆 Fore upper topsail 前上中桅帆 Forecastle 艏楼Forecastle deck 艏楼甲板 Fore peak 艏尖舱Fore perpendicular 艏垂线 Forged steel stem 锻钢艏柱 Forward draft mark 船艏吃水 Framing 骨架 Freeboard 干舷Freeing port 排水口Fresh water loadline 淡水载重线 Fresh water tank 淡水柜 Fuel box 燃油箱Fuel oil tank 燃油舱Fulload waterline 满载水线 Funnel 烟囱 GGaff 纵帆斜桁Gaff foresail 前桅主帆 Gaff mainsail 主帆 Gangway 舷梯Galley (船上)厨房 Gas line valve 气管阀 Gasket 垫圈Gasoline tank 汽油箱 Gear 小齿轮Gearwheel 大齿轮General cargo ship 杂货船 Girder of foundation 基座纵桁 Goalpost 门型桅(柱) Goahead and goback 前进和后退Grating 防滑格子、格兰丁Gravity type boat davit 重力式吊艇架 Guide rail 导轨Guide roller 导向滚轮 Gunwale 船舷上缘Gunwale angle 舷边角钢Gunwale rounded thick strake 舷边圆弧后板 Gusset plate 菱形板 Guy 稳索Guyline 定位索Gypsy 链轮(锚机上的) Gyropilotsteering indicator 自动操舵操纵台 Gyroscope 回转仪 HHalf beam 半梁Half depth girder 半深纵骨Half rounded flat plate 半圆扁钢 Half round steel bar 半圆钢 Hand crank 手摇柄 Handrail 手栏杆 Hand wheel 手轮 Handle 把手 Hatch 舱口精品文库欢迎下载- 8 -Hatch beam sockets 舱口梁座 Hatch coaming 舱口围 Hatch cover 舱口盖Hatch cover rack 舱口盖板隔架 Hatch end beam 舱口端横梁Hatch side cantilever 舱口悬臂梁 Hatch side girder 舱口纵桁 Hatchway 舱口 Hawsehole 锚链孔 Hawse pipe 锚链筒 Head rope 艏缆 Heel piece 艏柱根 Helicopter 直升机Helicopter deck 直升机甲板 Highpressuresoft pipe 高压软管 Hinge 铰链Hinged hatch cover 铰链舱盖Hinged stern door 尾部吊门(滚装船) Hogging 中拱弯曲 Hold 货舱Hold ladder 货舱梯子 Hold pillar 货舱内支柱 Hook 钩Hook bolt 钩头螺栓Horizontal girder 水平桁Horizonatal stiffener 水平扶强材 Hull 船壳Hull plank 船壳板Hydraulic cylinder 液压油缸Hydraulic pump 液压泵Hydraulic revolving crane 液压回转式起重机 Hydrofoil 水翼Hydrofoil craft 水翼艇 IIcebreaker 破冰船Icebreaker bow 破冰型船首 Independent tank 独立舱柜Inflatable liferaft 气胀式救生筏 Inflation valve 充气阀 Inner bottom plate 内底板 Inner door 内门(滚装船) Inner plate keel 内平板龙骨 Integral tank 整体舱柜Intermediate frame 中间肋骨Internal combustion engine set 内燃机组 JJack 船首旗Jack staff 船首旗杆Jack up drilling plattform 自升式钻井平台 Jet 喷筒Jet foam ejector 泡沫灭火枪 Jet pipe 喷管Jib 首帆,起重机的臂 Jig 支架 Joint 接头Joint shackle 连接卸扣 KKeel 龙骨Kenter shackle 双半式连接链环精品文库欢迎下载- 9 -King post 主柱 Knee 肘板 LLadder 梯子 Ladder way 步梯 Launch 下水 Lavatory 洗手间 Lead block 导向滑车 Lead sheave 导向槽轮Leading edge 导边(螺旋桨边) Lever chain stopper 闸刀式制链器 Length 船长Length overall 船总长 Lifeboat 救生艇 Lifebuoy 救生圈 Lifejacket 救生衣 Liferaft 救生筏 Lifting hook 艇吊钩 Light bulb 灯泡Light derrick 轻型吊杆 Light hold 空舱Light load waterline 空载吃水 Lightening hole 减轻孔Limbers board 舭部污水道顶板 Linkage handle 联动把手Liquid bulk cargo carrier 液体散货船 Liquid chemical tanker 液体化学品船Liquefied natural gas carrier 液化天然气船 Liquefied petroleum gas carrier 液化石油气船 Loding line 载重线Local strength 局部强度 Locker 立柜Longitudinal 纵骨Longitudinal bulkhead 纵舱壁 Longitudinal bending 总纵弯曲Longitudinally framed system 总纵强度 Loud speaker 扩音器 Lower deck 下甲板Luffing winch 变幅绞车 MMain frame 主肋骨 Main engine 主机 Main mast 主桅 Manhole 人孔Manhole cover 人孔盖 Margin plate 边板 Mast 桅Mast antenna 桅杆天线 Mast clutch 桅座 Masthead light 桅灯 Mast house 桅屋 Mattress 床垫Maximum breadth 最大宽度 Merchant ship 商船 Mess table 餐桌 Mixer 混合器Molded breadth 型宽 Molded depth 型深Molded dimension 船舶型尺度 Mooring hole 系缆孔精品文库欢迎下载- 10 -Mooring post 系缆桩 Multianglefairlead 滚柱导缆器 Multipurpose carrier 多用途船Mushroom ventilator 菇形通风筒 NNavigation area 航区Navigation bridge 驾驶台 Navigation deck 航海甲板 Navigation light 航行灯 Navigation radar 航海雷达 Nitrogen bottle 氮瓶 Nonreturn valve 止回阀Nose cone 螺旋桨整流帽 Notch 切口 Nozzle 喷嘴 Nut 螺母 OOar 浆Oblique bitts 斜式双柱系缆桩 Officer 驾驶员 Oil filler 加油点Oil intake pipe 进油管 Oil tanker 油船 Open rail 栅栏杆 Opening 开口Ore carrier 矿砂船 Outboard motor 舷外机Outer jib 外首帆 Outfitting 舾装Outrigger 舷外吊杆叉头 PPaddle 浆Parting arrangement 强胸结构、抗拍击结构 Panting beam 强胸横梁、抗拍击横梁 Partition 隔板 Passage 人行通道 Patch board 堵漏板 Patch bolt 堵漏螺杆 Pillar 支柱 Pin 销子 Pitch 螺距 Piston 活塞Piston rod 活塞杆Pitting 蚀损斑、氢气泡疤 Plane bulkhead 平面舱壁 Plate 平板Plate keel 平板龙骨 Platform 平台Pontoon hatch cover 箱形舱盖 Poop 艉楼 Port 左舷Port light 左舷灯Portable foam fire extinguisher 手提泡沫灭火器 Portal frame crane 龙门架式起货机 Position stop 限位器 Pressure gauge 压力表 Project 探照灯精品文库欢迎下载- 11 -Project davit 探照灯吊杆 Propeller 螺旋桨 Propeller cave 浆穴 Propeller post 螺旋桨柱Propeller shaft bracket 尾轴架 Provision store 食物储备室 Pudding 软垫Pudding fender (护舷)碰垫 Pump 泵Pump room 泵房PVC foamed plasticPVC 泡沫塑料 QQuadrant 舵柄 Quarter 居住区Quarter pillar 舱内侧梁柱 RRadar 雷达Radar indicator 雷达指示器 Radial davit 悬臂吊艇架 Raft 筏Rail 栏杆、轨道Raked bow 前倾型船艏Range light 后桅灯、距离灯 Ramp 跳板、滑道 Rear door 后门Reduction gear box 减速箱 Reeling drum (绞车)主卷筒 Refrigerated room 冷藏室 Registered port 注册港 Reverse frame 内底横骨Rig 索具、钻井平台Right angle gunwale 直角舷边 Roller 滚轮、滚柱Roller bearing 滚柱轴承 Roller fairlead 滚轮导缆器 Rope 缆绳Rotating chassis 回转底盘(克令吊) Rotating platform 回转平台Rotary screw propeller 回转式螺旋推进器 RoRoship 滚装船Rubber 橡胶、橡皮Rubber packing 橡胶填料、橡皮条 Rudder 舵Rudder bearing 舵承 Rudder blade 舵叶Rudder control rod 操舵杆 Rudder plate 舵板 Rudder post 舵柱 Rudder spindle 舵轴 Rudder stock 舵杆 Rudder trunk 舵杆围阱 SSafety valve 安全阀 Sand box 沙箱Sanitary tank 清洁用水柜 Sail 帆Salver (tray ) 托盘 Sampan 舢板Screen bulkhead 轻型舱壁精品文库欢迎下载- 12 -Screw 螺旋桨、螺钉、螺杆Screw compressor 螺旋式制链器 Screw propeller 螺旋桨 Scupper 排水孔 Scuttle 舷窗 Seal ring 密封圈 Seam 边接缝Search light 探照灯 Semibalanced rudder 半平衡舵 Semisubmersibledrilling platform 半潜式钻井平台 Servo system 伺服系统 Sewage 污水Shaft bossing 轴毂 Shaft coupling 联轴节Shaft tunnel (passage ) 轴隧 Sheave 滑车轮、槽轮 Sheer 舷弧Sheer strake 舷顶列板 Sheet 帆脚索 Shell 船壳Shell plate 船壳外板 Ship bottom plug 船底塞 Shipyard 船厂Shoe piece 艉柱踵材 Short beam 半梁 Shroud 桅牵索 Side 舷边Side frame 舷侧肋骨Side keelson 旁内龙骨 Sideligth 舷灯Side plate 舷侧外板 Side scuttle 舷窗Side stringer 甲板边板 Signal bell 信号钟 Silencer 消音器 Single bottom 单底Single cylindrical roller chock 单柱式导缆钳 Single plate rudder 平板舵 Skylight 天窗 Sleeve 衬套Slewing guy 摆动稳索Slewing hydraulic motor 回转液压马达Sloping bottom plate of topside tank 顶边舱斜底板 Sloping top plate of bottom side tank 底边舱斜顶板 Sofa 沙发Soft ladder 软梯 Spade rudder 悬挂舵 Spare parts 备件 Speedometer 测速仪 Sponson deck 舷伸甲板 Spray gun 喷枪 Stability 稳性 Stairway 扶梯 Stanchion 支柱 Starboard 右舷Steel structure 钢结构 Steering gear 舵机Steering wheel 方向盘、舵轮精品文库欢迎下载- 13 -Stem 船艏Stem anchor 艏锚 Stern 船艉Stern anchor 艉锚 Stern ramp 艉跳板 Stern shaft 尾轴Stern shaft tube 尾轴管 Stern transon plate 艉封板 Stiffener 加强板Storage battery 蓄电池 Store box 备用柜Strengthen deck 强力甲板 Stuffing 填料Summer loadline 夏季载重线 Superstructure 上层建筑 Swage plate 牙筋板Swash plate 止荡板、防波板 Switch board 配电板Swivel link 转环(锚链) TTailstabilizer anchor 尾翼式锚 Tank lid 货油舱盖Tank valve 货舱阀(油船) Tanker 油船 TbarT 型材Tiller 舵柄Timber carrier 木材运输船 Throttle valve 节流阀Thruster 侧推器Thruster bearing 推力轴承 Tool box 工具箱Topping lift (line ) 千斤索 Topping lift block 千斤滑车 Topside tank 顶边舱 Torsion 扭转Trailing edge 随边(螺旋桨叶) Transverse bulkhead 横舱壁 Tug 拖轮 Tunnel 轴隧Turnable blade 可转动浆叶 Turning indicator 回转指示器 Tweendeck cargo space 甲板间舱 Tween screw 双桨 UU sharp tankU 形水舱Universal fairlead 万向导缆器 Upper deck 上甲板 VVapor 蒸汽Vapor pipe 蒸汽管子 Valve 阀Valve seat 阀座Variable pitch screw propeller 可变螺距螺旋桨 Ventilator 通风筒Ventilator duct 通风管道 Ventilator trunk 风路 Vertical bow 垂直型船艏 Vertical girder 竖桁精品文库欢迎下载- 14 -Vertical shaft 垂直传动轴 Viewfinder 反光镜 View screen 旋转视窗 WWaist band 腰带Warping drum 系缆滚筒 Warping winch 系缆绞车 Warship 战舰、军舰 Wash basin 洗脸盆 Water boiler 开水锅炉 Water closet 抽水马桶 Water filter 水过滤器 Watertight 水密Watertight door 水密门 Watertight floor 水密肋板 Watertight stuffing 水密填料 Weather deck 露天甲板 Web 腹板Web beam 强横梁 Web frame 强肋骨 Wheel 车轮 Whistle 汽笛 Winch 绞车 Windlass 锚机Windlass gipsy 起锚机卷筒 Window certain 窗帘 Windshield 挡风玻璃 Wingkeel 翅龙骨Wing deck 两翼甲板Wing tank 边舱 Wire rope 钢索Wire rope fall 滑车钢丝绳 Wireless antenna 无线电天线 Wooden structure 木结构 Worm 蜗杆Worm wheel 蜗轮 YYacht 游艇 Yard 船厂二、轮机词汇AAdapter 驱动器Adjustable wrench 活动扳手 Adjusting ring 调整环 Adjusting screw 调节螺钉 Adjusting valve 调节阀 Adjusting washer 调节垫圈 Air adjust screw 空气调节螺钉 Air admission valve 进气阀 Air bottle 空气瓶Air charge cooler 进气冷却器 Air charge valve 充气阀 Air cleaner 空气滤清器 Air compressor 空气压缩机 Air cooler 空气冷却器Air cooler frame 空气冷却器壳体 Air conditioner 空调Air distributor 空气分配器精品文库欢迎下载- 15 -Air escape valve 排气阀 Air filter 空气过滤器 Air impeller 空气叶轮Air induction valve 进气阀 Air inlet valve 进气阀 Air motor 空气马达Air outlet valve 排气阀 Air pipe 空气管 Air piston 空气活塞 Air pump 空气泵Air purifier 空气净化器Air reducing valve 空气减压阀Air refrigerated plant 空调制冷装置 Air release valve 放气阀 Air seal 气封Air spring 空气弹簧Air starting device 空气启动装置 Air switch 空气开关 Air tight door 气密门 Alternator 交流发电机 Aluminum anode 铝块保护Anchor and chain gear 锚链设备 Anchor chain 锚链Anchor chain meter 锚链拉力器 Angle lever 角杆 Anticorrosive grease 抗蚀牛油Applicator for all purpose nozzle 多用途喷嘴接头 Assembling nut 螺母套 Attachment bolt 连接螺栓Automatic alarm 自动报警Automatic regulator 自动调节器 Automatic stop valve 自动控制阀 Automatic switch 自动开关 Axle box 轴箱 Axle bush 轴套 Axle key 轴键 Axle sleeve 轴套 BBalance bush 平衡轴套 Balance rudder 平衡舵 Balance valve 平衡阀 Balance wheel 飞轮 Ball bearing 滚珠轴承 Band 卡圈Banding screw buckle 带扣螺丝管夹 Base 底座Bearing bush 轴承套 Bearing cover 轴承盖 Bearing shell 轴瓦Bearing stopper 轴承压盖 Bearing ,lower part 下轴承 Bearing ,upper part 上轴承 Bleeder screw 泄放螺丝 Blind flange 盲法兰 Blind joint 封闭接头 Blind nut 螺帽 Block valve 截断阀 Blowoff pipe 放气阀精品文库欢迎下载- 16 -Body 本体Body packing 本体填料Boiler accessories 锅炉附件 Boiler alarm 锅炉报警 Boiler bedding 锅炉座 Boiler blowoutpipeline 锅炉排污管Boiler feed pump 锅炉给水泵 Boiler fittings 锅炉附件 Boiler flat 锅炉平台 Boiler furnace 锅炉炉膛 Bolt 螺栓Bolt tension machine 螺栓拉力测量仪 Bonnet 管帽 Boss 轮毂Bottom cover 底盖Bottom flange 底部法兰 Bracket 支架、三角板 Brake 制动器、刹车 Brass cap 铜管帽Brass cross 十字形铜接 Brasselbow 黄铜弯头Brass hexagon nipple 黄铜六角外螺丝 Brass needle valve 黄铜针阀Brass reducing socket 黄铜异径套管 Brass short nipple 黄铜短外螺丝 Breaker bolt 安全螺栓 Breather valve 通气阀 Brine pipe 海水管Buffer 缓冲器Bursting plate 安全板 Bush 布司(轴承)Bushing for roller guide 滚轮导套衬套 Butterfly bolt 蝶形螺栓、元宝螺栓 Butterfly nut 蝶形螺母 Butterfly valve 蝶阀 CCabin thermometer 室内温度器 Cable 电缆Cable bushing 电缆衬套 Cable cutter 电缆钳 Cam 凸轮Cam clearance 凸轮间隙 Cam driven 凸轮驱动 Cam roller 凸轮滚柱 Cam shaft 凸轮轴Cap head square neck bolt 盖头四角颈螺栓Carbon dioxide fire extinguisher 二氧化碳灭火器 Carboncotton packing 石棉填料Carborundum oil stone 油石 Case 箱子Cast alloy 铸造合金 Cast brass 铸造黄铜 Cast bronze 铸造青铜Cast copper alloy 铸铜合金 Cast ingot 铸锭 Cast iron 铸铁 Cast pipe 铸管精品文库欢迎下载- 17 -Cast steel 铸钢Centering shaft 中心轴Chain drive and guide bar 链传动及导杆 Chain link 链环Chain wheel 链轮传动Charge air pipe 增压空气管 Check plate 挡板 Checked plate 花铁板 Check pin 止动销 Check screw 固定螺丝 Check valve 止回阀Check valve body 止回阀本体 Check valve case 止回阀壳体 Clamp 夹具、马脚 Clamp screw 夹紧螺丝 Clamp washer 夹具垫圈 Clamp arm 夹臂Clamping piece 夹件 Cleaning pipe 清洁管 Cleaning valve 清洗阀 Clutch body 离合器体 Clutch coupling 离合器 Clutch cover 离合器盖 Clutch gear 离合器齿轮 Clutch joint 离合器接头 Clutch pin 离合器销 Clutch rod 离合器拉杆 Clutch shaft 离合器轴 Coil 线圈Combined brine/air ejector 海水/空气混合喷射泵Combustible gas detector 可燃气体检测器 Compensation valve 平衡阀 Compression ring 压缩环 Cone 圆锥体Conical bore 锥孔 Conical valve 锥形阀 Connection 接头Constant pitch propeller 定距螺旋桨 Constant speed governor 定速调速器 Control handle 控制手柄 Control lever 操纵杆Cooling fin 散热片、冷却片Cooling fresh water pump 淡水冷却柜 Cooling jacket 冷却水套 Cooling oil pipe 冷却油管路 Cooling system 冷却系统Cooling water connection 冷却水接头 Copper pipe 铜管 Cotter pin 开口销Coupling 联轴节、考 必令 Coupling flange 连接法兰 Cover plate 盖板Crank pin bearing shell 曲轴销轴瓦 Crank shaft gear 曲轴齿轮 Crank web 曲轴臂 Crankcase 曲轴箱Crankcase cover 曲轴箱盖Crankpin bearing cap 曲轴销轴承盖 Crankshaft 曲轴Crankshaft distortion dial gauge 曲轴拐挡表精品文库欢迎下载- 18 -Cross machine screw 十字槽螺钉 Crosshead 十字头Crosshead bearing cap 十字头轴承盖 Crosshead bearing shell 十字头轴瓦 Crump band 卡环 Cut ring 挡水环 Cylinder 气缸Cylinder block 气缸体 Cylinder body 气缸体 Cylinder bore 气缸内径 Cylinder cap 气缸盖 Cylinder cover 气缸盖 Cylinder head 气缸盖Cylinder head bolt 气缸盖螺栓 Cylinder liner 气缸衬套 Cylinder pin 气缸销Cylindering pin 圆柱形销 DDamper 减震器 Dead center 止点 Deflector 定位螺钉 Dehumidify 除湿 Demister 去雾器Depth micrometer 深度测微器 Dial gauge 测微器 Diaphragm 隔膜Diaphragm valve 膜片阀 Diesel oil 柴油 Disc 圆盘Disc valve 圆盘阀Discharge valve 排出阀 Distance bushing 定距套 Distance ring 定距环Distributing cover 分配器壳体 Distributing plate 分配板 Distributor disc 配电盘 Distributor plate 配电板 Dosing ring 进料环Double direction thrust ball bearing 双向推力轴承 Double open end wrench 双头开口扳手 Drain tube 放残管 Drain valve 防残阀 Drive chain 传动链 Drive gear 主动齿轮Drive gear box 主动齿轮箱 Drive screw 驱动螺杆 Driven gear 从动齿轮 Driven shaft 从动轴 Driving key 传动键 Driving pin 压销 Driving shaft 传动轴 Driven wheel 传动轮 Dust cap 防尘罩 Dust catcher 吸尘器 Dust cover 防尘罩 Dust seal 防尘密封 Dust remover 防尘器 EEccentric 偏心轮Ejector nozzle 喷射嘴精品文库欢迎下载- 19 -Ejector pipe 喷射管Elastic clutch 弹性离合器 Elbow 弯头Elbow joint 弯头接头 Elbow pipe 弯管 Electric arc 电弧 Electrical brush 电刷Electrical governor 电子式调速器Electrician screwdriver 电工用螺丝起子 Element for filter 滤器滤心 Emery cloth 纱布 End cover 端盖 End cap 端盖 End housing 端盖 End pin 尾销 End plate 端板 End ring 端环 Engine base 机座 Engine bed 机座Engine frame safety valve 机架安全阀 Engine igniter 助燃剂Engine indicator 功率指示器Engine peak indicator 爆发压力示功器 Exhaust boiler 废气锅炉 Exhaust cam 排气凸轮 Exhaust pipe 排气管 Exhaust valve 排气阀Extension spring 受拉弹簧 Eye bolt 吊环螺栓 FFan 鼓风机Fan blower 通风机 Fan house 风室 Fan wheel 风轮Feed piping 给水管系 Feed valve 给水阀 Filter 过滤器 Filter bowl 滤筒 Filter drum 滤筒 Filter net 滤网 Fin 散热片Fire hose box 消防皮龙箱Fire hose nozzle 消防皮龙喷嘴 First stage gear 一级齿轮 Fitting flange 连接法兰 Fitting plate 垫板 Fixing bolt 固定螺钉 Fixing pin 定位销 Fixing plate 固定板 Flange 法兰Flange nut 法兰螺母 Flat key 平键Flexible hose 柔性管 Float 浮子Float switch 浮子开关 Float valve 浮阀 Flow meter 流量计 Flow switch 流量开关 Fly wheel 飞轮Friction block 摩擦块精品文库欢迎下载- 20 -Front cover 前盖Fuel oil injection pipe 高压油管 Fuel oil injection pump 高压油泵 Fulcrum 支点 GGas inlet port 进气口 Gas outlet 排气口 Gasket 密封垫Gasoline (petrol ) 汽油 Gauge 表 Gear 齿轮Gear clutch 齿轮离合器 Gear pump 齿轮泵 Gear train 齿轮组 Gland 压盖Gland box 填料函 Gland cover 填料压盖 Gland housing 填料函 Gland packing 密封填料 Gland seal 密封填料 Governor 调速器Governor body 调速器本体 Governor box 调速箱Governor driven gear 调速器从动齿轮 Governor driving gear 调速器传动齿轮 Governor handle 调速手柄 Governor lever 调速杆 Governor rod 调速杆 Governor shaft 调速轴 Grate 格栅Gravity disk 重力盘 Grease gun 牛油枪 Grease nipple 牛油咀 Grease oil 牛油Gudgeon pin 十字头销 Guide 导板Guide blade 导向叶片 Guide block 导块 Guide bushing 导套 Guide cam 导向凸轮 HHandle 手柄Handle stopper 止动杆 Hand wheel 手轮 Head cover 前盖Heat exchanger condenser 冷凝气热交换器 Heat exchanger evaporator 蒸发器 Heavy duty pump oiler 强力油泵 Hexagon bushing 六角衬套Hexagon flange nut 六角法兰螺帽Hexagon socket head cap screw 内六角盖头螺钉 Hinge 铰链Hinge joint 铰链接头 Hinge pin 铰链销 Holder ring 定位环 Hose nipple 软管接头 Hose line 软管Hydraulic governor 液压调速器 Hydraulic jack 液压千斤顶 Hydraulic pump 液压泵精品文库欢迎下载- 21 -Hydraulic seal 水(压密)封Hydrometers for light oil 轻油比重计 IIgnition 发火装置 Impeller 叶轮Impeller casing 叶轮箱 Impeller key 叶轮键 Impeller nut 叶轮螺母 Impeller pump 叶轮泵 Impeller shaft 叶轮轴 Indicator 指示器Indicator cam 指示器凸轮 Indicator valve 示功器 Inducer 叶轮Inducer key 导风轮键 Inlet elbow 进口弯头 Inlet pipe 进口管 Inlet valve 进口阀 Inner case 内套 Inner link 内链环 Inner ring 内环 Input shaft 主动轴Inspection glass 观察镜 Insulating joint 绝缘接头 Insulating disc 绝缘板 Insulation cover 绝缘盖板 Intermediate bearing 中间轴承Intermediate shaft cover 中间轴承盖 Iron block 铁块 JJacket cooling water 气缸套冷却水 Jacket water inlet 气缸套冷却水进口 Joint 接头Joint nut 接头螺母 Joint piece 连接件 Joint seat 连接座 Junction block 连接块 Junction box 接线盒 Junction bolt 连接螺栓 Junction pipe 连接管 Junction plate 连接板 KKerosene 煤油 Key 键Key slot 键槽 Knob 旋钮 Knock 止动销 LL .O .(lubricate oil ) 润滑油 L .O .nozzle 滑油喷嘴L .O .pump body 滑油泵本体 L .O .pump cover 滑油泵端盖L .O .pump driven gear 滑油泵从动齿轮 L .O .pump driving gear 滑油泵主动齿轮 L .O .cut plate 挡油板Lamella for scraper ring 刮油环薄片 Lever 杆 Lid 盖Lifeboat compass 救生艇磁罗经 Lifting bolt 吊环精品文库欢迎下载- 22 -Lifting eye 吊环 Lifting stud 支撑轴 Liner 衬套Liner for spindle guide 阀杆导套衬套 Link 连接环Link joint 活动连接 Link pin 连杆销 Link rod 连杆 Lock 锁Lock pin 固定销Lock washer 锁紧垫圈 Locking claw 止动爪 Locking ring 锁紧环 Locking wire 锁紧丝 Locknut 防松螺丝Lub oil pump 润滑油泵 Lubrication pipe 润滑油管 Lubricator 主油器 MMachine tool 机床Machinist file 三角锉刀 Main bearing 主轴承Main bearing shell 主轴瓦Main bearing stud 主轴承双头螺栓 Main driving gear 主传动齿轮 Main spring 主弹簧Male cross 外螺十字接头 Male elbow 外螺纹弯头 Manhole cover 人孔盖 Manifold 总管Manometer 压力计Marine bronze 船用青铜 Marine cast iron 船用铸铁 Marine cast steel 船用铸钢 Marine forged steel 船用锻钢 Measuring tape 卷尺Mechanical joint 机械连接 Mechanical seal 机械密封 Metal lining 金属衬板 PPipe seal 管封 Piston 活塞Piston rod 活塞杆 Piston skirt 活塞裙 Pitch 沥青Plane washer 平垫圈 Plastic hammer 塑胶锤 Plate clutch 圆盘离合器 Plug 旋塞 Plunger 柱塞Pneumatic sump pump 气动式潜水泵 Pointed cone 尖锥 Pointed drill 尖钻 Pointed screw 尖头螺钉Portable oxygen indicator 可携式测氧仪 Portable ejector 手提喷射泵 Power wrench 省力扳手 Pressing bolt 压紧螺丝 Pressing ring 压紧环 Pressure gauge 压力计精品文库欢迎下载- 23 -Pressure valve 压力阀 Pull rod 拉杆Pump impeller 叶轮泵 Push button 按钮 Push rod 推杆 QQuick coupling ,complete 活接头总成 RRack rail 齿条 Wheel 齿轮Reducing gear 减速齿轮 Regulating nut 调整螺母 Regulating ring 调整环 Relief plug 释放塞 Relief ring 保险环 Relief valve 安全阀 Resilient arm 强力臂 Return main 回流总管 Return pipe 回流管 Return valve 回流阀 Reversing shaft 逆转轴 Reversing valve 换向阀 Ring 环Ring gasket 衬圈 Ring valve 环形阀 Rod 杆Roller 滚轮Rotary pump 回转泵 Rotary valve 回转阀Rotor side ring 转子侧环Round nut 圆头螺母 Rubber cord 橡胶条 Rubber hammer 橡胶锤Rubber protective steeve 橡胶保护套 Rubber seal 橡胶密封 Rust preventive 防锈圈 SSafety bolt 贯穿螺栓 Safety cap 安全帽 Safety cock 安全旋塞 Safety collar 安全环 Safety valve 安全阀Scavenge air recciver 扫气箱 Scraper ring 刮油环 Screw 螺钉 Screw die 板牙 Screw nut 螺母 Seal noise 密封Seal washer 密封垫圈 Seat 座Seat ring 环座Seawater pipe from condenser 冷凝器海水管 Second stage gear 二级齿轮 Separator 分离器Servo brake 伺服制动器 Servo clutch 伺服离合器 Servo drive 伺服传动 Servo lever 伺服杆Servo oil cylinder 伺服油缸 Servo pump 伺服泵精品文库欢迎下载- 24 -Set hammer 扁锤 Set nut 固定销 Set ring 固定环 Shaft 轴 Shaftpin forShaftpinfor roller 滚轮轴销 Shaft alley 轴隧 Shaft bearing 轴承 Shim 垫片Shock absorber 减震器 Shrink ring 扣环 Shutoffvalve 截止阀Sight glass 观察镜 Silencer ring 消音环 Sleeve 套管Sleeve coupling 轴套联轴节 Sleeve nut 套管螺母 Slide 滑块 Slide bar 滑杆 Slide valve 滑阀 Slider door 滑动门 Slider hook 滑钩 Sludge burner 焚烧炉 Socket 套管Special nut 专用螺母 Special tool 专用工具 Special plug 专用旋塞Speed control nut 调速螺母 Spherical valve 球阀 Split pin 开口销 Spindle 阀杆Spindle guide 阀杆导套 Spray nozzle 喷嘴 Spray pipe 喷管 Spring 弹簧Spring pin 弹簧销 Spring valve 弹簧阀 Stainless steel 不锈钢Stainless steel head plug 不锈钢方头止栓 Start valve 启动阀Starting air bottle 启动空气瓶Starting air compressor 启动空气压缩机 Starting air pipe 启动空气管Starting air relief valve 启动空气安全阀 Starting air stop valve 启动空气截止阀 Starting air timing valve 启动空气分配阀 Starting air valve 启动空气阀 Staror 定子Stay bolt 贯穿螺栓Steam injector 蒸汽喷射泵 Steel compasses 钢质圆规Steering alarm indicator 舵机报警指示器 Steering chain 转舵链Steering cylinder 舵机液缸 Steering gear 舵机Steering switch 舵机开关 Steering wheel 舵轮。

船厂造船及修船船体、轮机、电气三大专业实用英语汇总

船厂造船及修船船体、轮机、电气三大专业实用英语汇总
船底板
shell plate
船外板
bow plate
船艏外板
bracket plate
肘板
bulkhead plate
舱壁板
corrugated bulkhead plate
槽型舱壁板
bulwark plate
舷墙板
coaming plate
围板
connection plate
连续板
copper sheathing steel plate
平衡块
hinge
铰链
handle
把手
二、焊接
groove
支柱
frame
肋骨
base frame
基础台架
bear frame
支架
bilge frame
舭肋骨
bottom frame
船底肋骨
bow frame
首肋骨
bracket frame
肘板框架肋骨
bulbous bow frame
球鼻首肋骨
bulbous frame
球曲型肋骨
chief frame
主肋骨
铜-钢复合板
deck stringer plate
甲板边板
sloping plate
斜板
reinforcement plate
加强板
rudder plate
舵板
side plate
舷侧外板
skirt plate
裙板
stem plate
艏柱板
stern plate
艉柱板
platform
平台
engine-room platform
舭纵桁、舭纵骨

船舶、轮机英语词汇大全

船舶、轮机英语词汇大全

船舶英语目录一.职位及工种(Titles and type of work) (1)二、柴油机类(Words about diesel engine) (3)三、船舶机械类(Words about marine machinery) ·· 11四、阀门(Words about valve) (14)五、泵类(Words about pump) (16)六、甲板机械类(Deck machinery) (18)七、工具类(Word about tools) (20)八、常用物料(Material in common use) 26九、常用紧固件(Part of fixation in common use) (28)十、常用油类(Oil in common use) (28)十一、常用量词(Quantifier in common use) (29)十二、国家名称(Name of country) 。

30十三、常用缩语(abbreviation in common use) (31)十四、船用动态常用单词(marine tends word) 32 十五、船舶机电设备操作词汇(manipulate of marine equipment) ·33十六、故障常用单词(words about malfunction) (35)十七、保养检修常用词汇(Words about maintain and examination) 38 十八、常用数字(Numeral in common use) 40十九、时间、季节与方向(Time、Season and Direction) (42)二十常用词组(Phrases in common use)·45二十一、常用动词和例句(Verb in common use and example) (48)二十二、问候和常用表达语(Greeting and common expression) (67)二十三、主机提交过程用语(Delivery expressions for main engine) 68 二十四、空压机和空气系统用语(Air compressor and Air system) (75)二十五、锅炉提交用语(Delivery expressions for boiler) (77)二十六、锚绞车提交过程用语(Delivery expressions for anchor windlass) 79二十七、舵机提交过程用语(Steering gear delivering) (87)二十八、付机提交过程用语(Delivery expression for A/E) (91)二十九、救生艇提交过程用语(Delivery expressions for lifeboat) ··92 三十、其他提交项目(Delivery expressions for other items) (95)三十一、甲板机械系泊试验(Mooring test for deck machinery) (96)三十二、机舱设备系泊试验(Mooring test for the equipment in E/R) (98)三十三、谈论故障常用语(Expressions for trouble) (100)三十四、谈论检修常用语(Expressions for overhaul) (101)三十五、谈论试验和检验(Talking about test & check) (103)三十六、谈论技术要求(Talking about technology required) (105)一.职位及工种(Titles and type of work) 1.船长 Captain2.大副 Chief officer3.二副 Second officer4.三副 Third officer5.四副 Fourth officer6.水手长 Boatswain7.水手 Sailor & Seaman8.木匠 Carpenter9.轮机长 Chief engineer 10.大管轮 Second engineer11.二管轮 Third engineer12.三管轮 Fourth engineer13.机匠长 Chief motorman15.机匠 Fitter16.加油工 Oil man17.大电 Chief electrician18.电工 Electrician19.车间主任 Workshop director20.工长 Section chief21.班长 Fore man22.钳工 Fitter23.主管工程师 Engineer in charge24.机务&船东 Superintendent &Super &Owner25.助理工程师 Assistant engineer26.验船师(机)Register27.验船师(船)Surveyor28.油漆工 Painter29.焊工 Welder30.大橱 Chief cook31.物料员 Store keeper32.加油工 Oiler33.机工 Mechanic34.甲板员 Deck man35.电线工 Wireman36.外包工 Laborer37.铸工 Molder38.管子工 Pipe fitter39.起重工 Crane operator二、柴油机类(Words about diesel engine)1.主机 Main engine2.二冲程柴油机 Two-stroke diesel engine3.四冲程柴油机 Fore-stroke diesel engine4.高速柴油机 High speed diesel engine5.中速柴油机 Middle speed diesel engine6.低速柴油机 Low speed diesel engine7.气缸盖(缸头) Cylinder head8.安全阀 Safety valve9.释放阀 Relief valve10.示功阀 Indicator valve11.示功考克 Indicator cock12.空气起动阀 Air starting valve13.起动空气分配器 Air starting distributor14.油头(燃油喷射器) Fuel injector15.排气阀 Exhaust valve16.气缸套 Cylinder liner17.冷却水套 Cooling water jacket18.气缸注油器 Cylinder lubricator19.活塞 Piston20.活塞头 Piston crown21.活塞裙 Piston skirt22.活塞销 Piston gudgeon pin24.活塞杆 Piston rod25.活塞环 Piston ring26.活塞环槽 Piston ring groove27.压缩环 (气环) Compression ring28.刮油环 (油环) Oil scraper ring29.减磨令 Wear ring (copper ring)30.伸缩管(水拉管) Telescopic pipe31.活塞冷却空间 Piston cooling space32.填料箱(函) Stuffing box33.填料箱密封环Sealing ring for Stuffing box34.填料箱压缩环 Pressure ring for Stuffingbox35.填料箱刮油环Scraper ring for Stuffing box36.扫气箱 Scavenging receiver37.扫气口 Scavenging port38.排气口 Exhaust port39.十字头 Cross head40.十字头销 Crosshead pin41.十字头轴承 Crosshead bearing42.十字头滑块 Crosshead slipper43.滑块 Guide shoe44.十字头导板45.连杆46.连杆大端轴承47.连杆小端轴承 Small end bearing48.曲柄轴承 Crank bearing49.曲柄销 Crank pin50.曲轴 Crank shaft51.曲轴颈 Crank journal52.曲柄臂 Crank web53.拐档差 Crank deflection54.主轴承 Main bearing55.主轴颈 Main journal56.轴承瓦 Bearing bush57.上轴瓦 Upper bearing bush58.上轴瓦 Upper half59.下轴瓦 Lower bearing bush60.下轴瓦 Lower half61.推力轴承 Thrust bearing62.推力块 Thrust pad63.推力盘 Thrust disc64.推力轴 Thrust shaft65.底座 Bed plate66.机架 Frame67.曲柄箱 Crank case68.曲柄箱导门 Crank case door69.曲柄箱防爆门 Explosion-proof Crank case.70.定时齿轮 Timing gear71.飞轮 Flying wheel72.凸轮 Cam73.凸轮轴 Cam shaft74.喷油凸轮 Fuel injection cam75.链条 Chain76.链条轮 Chain wheel77.链条箱 Chain box78.推杆 Push rod79.摇臂 Rocker arm80.排气阀 Exhaust valve81.吸气阀 Suction valve82.排气总管 Exhaust manifold83.进气总管 Air inlet manifold84.高压燃油管 High pressure fuel pipe85.活塞冷却水管 Piston cooling water pipe86.法兰 Flange87.贯穿螺栓 Tie bolt (tie rod)89.滑油泵 Lubricating oil pump90.燃油泵 Fuel oil pump91.滑油泵齿轮 Gear for lubricating oil pump92.燃油泵齿轮 Gear for fuel oil pump93.叶轮 Impeller94.柱塞 Plunger95.导杆 Guide rod96.导套 Sleeve97.滚动轴承 Ball bearing98.滑动轴承 Sliding bearing99.推力滚动轴承Thrust ball bearing100.推力面 Thrust surface (thrust side)101.盘车机 Turning gear102.增压器 Turbocharger103.涡轮机(透平) Turbine104.涡轮 Turbine wheel105.涡轮叶片 Turbine blade106.喷嘴 Nozzle107.废气叶轮 Exhaust impeller108.废气叶轮片 Exhaust blade109.废气端 Exhaust side110.透平端 Turbine side111.转子轴 Rotor shaft112.油泵 L.O.pump113.换向装置 Reversing device114.换向伺服期 Reversing servomotor115.压气机(鼓风机) Blower116.膨胀接 Expansion joint117.调速器 governor118.飞重 Flying weight119.补偿阀 Compensate valve120.针阀 Needle valve121.开口销 Cotter pin122.轴封 Shaft seal123.机械密封 Machinery seal124.配电盘 Switchboard 125.应急配电盘 Emergency switchboard 126.应急发电机 Emergency generator 127.滤器 Filter 128.细滤器 Filter 129.粗滤器 Strainer 130.滑油滤器 L.O. filter 131.燃油滤器 F.O. filter 132.空气消音器 Air intake silencer 132.空气滤器 Air intake filter 133.空气瓶 Air bottle (receiver) 134.分油机 Separator 135.油水分离器 Water-oil separator 136.净油机 Purifier 137.燃油净化器 F.O. purifier 138.二氧化碳 CO2 139.二氧化碳瓶 CO2 bottle 140.正时齿轮 Timing gear 141.导向棒装置 Guide bar 142.注油器驱动 Lubricator driver 143.链条张紧装置 Chain tightener 144.凸轮轴传动轮 Chain wheel on cam shaft 145.中间链链传动轮Intermediate chain wheel 146.注油器驱动装置Lubricator drive 147.链条张紧装置 Chain tightener 148.滚筒导座 Roller guide housing 149.应急操纵台 Emergency console 150.力矩平衡器 Moment compensator 151.主启动阀 Main starting valve 152.启动空气分配器Starting air distributor 153.喷油器 Fuel valve 154.扫气系统 Scavenge air system 155.安全帽 Safety cap 156.机座 Bed plate 157.轴向振动减振器 Axial vibration damper 158.贯穿螺栓 Arrangement of stay bolt 159.示功器驱动装置 Indicator driver 160.端罩 End shields 161.气缸架 Cylinder frame 162.气阀传动装置 Valve operating device 163.摇臂润滑油泵 Rocker arm lubricating oil pump 164.摇臂润滑油柜 Rocker arm lubricating tank 165.摇臂润滑滤器Rocker arm lubricating filter 三、船舶机械类(Words about marine machinery) 1.船用锅炉 Marine boiler 2.废气锅炉 Exhaust boiler 3.辅锅炉 Donkey boiler 4.组合式锅炉 Combined boiler 5.火管 Fire tube 6.给水管 Feed pipe 7.炉膛 Furnace 8.炉墙 Furnace wall 9.火侧 Fire side 10.水侧 Water side 11.燃烧器 Oil burner 12.安全阀 Safety valve 13.上排污 Upper drain 14.下排污 Lower drain 15.锅炉皮阀 Mounting valve 16.水位计 Water level gauge 17.压力表 Pressure gauge 18.主汽门 Main steam valve 19.玻璃管 Glass tube 20.空调装置 Air-conditioning plant 21.制冷装置 Refrigerating plant 22.冰机 Fridge. Machine 23.空气压缩机 Air compressor 24.造水机 Fresh water generator 25.板式冷却器 Plate type cooler 26.机舱天车 Engine room crane 27.天车导轨 Crane rail 28.电磁阀 Solenoid valve 29.舵机 Steering gear 30.舵承 Rudder bearing carrier 31.液压缸 Hydraulic cylinder 32.废气涡轮增压器Exhaust gas turbocharger 33.弹簧阀 Spring loaded valve 34.冷凝器 Condenser 35.分油器 Oil separator 36.轴带发电机 Shaft generator 37.焚烧炉 Oil burner 38.分油机 Separator 39.分离筒 Separator bowl 40.配水盘装置 Paring disc device 41.转数计 Revolution counter 42.控制阀 Control valve 43.辅机 Auxiliary machinery 44.制冷装置 Refrigerating plant 45.海水淡化装置Sea water desalting plant 46.热交换器 Heat exchanger 47.船用气瓶 Marine air bottle 48.冷风机 Cooler unit 49.防水风门 Fire damper 50.气密挡板 Gas tight damper 51.排气风机 Exhaust fan 52.舱室通风机 Cabin fan 53.机舱通风机 Engine room fan 54.应急鼓风机 Emergency blower 四、阀门(Words about valve) 1.吸气阀 Suction valve 2.排气阀 Exhaust valve 3.控制阀 Control valve 4.导 阀 Pilot valve 5.单向阀 Non-return valve 6.口琴阀 Flap valve 7.调节阀 Regulating valve 8.液压阀 Hydraulic valve 9.膨胀阀 Expansion valve 10.给水阀 Feed valve 11.排水阀 Discharge valve 12.截止阀 Stop valve 13.吹泄阀 Blow-off valve 14.空气阀 Air valve 15.泄放阀 Drain valve 16.止回阀 Check valve 17.海底阀 Sea valve 18.回流阀 Retune valve 19.节流阀 Throttle valve 20.进气阀 Inlet valve 21.出气阀 Outlet valve 22.热力阀 Thermal valve 23.中央阀 Center valve 24.单向阀 One way valve 25.二通阀 Two way valve 26.三通阀 Triple valve 27.旁通阀 By-pass valve 28.换向阀 Change-over valve 29.减压阀 Pressure-reducing valve 30.溢流阀 Overflow valve 31.自闭阀 Self-locking valve 32.针阀 Needle valve 33.平衡阀 Balance valve 34.循环阀 Circulation valve 35.主 阀 Main valve 36.滑 阀 Slide valve 37.蝶 阀 Butter-fly valve 38.截止阀 Shut-off valve 39.闸板阀 Gate valve 40.通海阀 Sea suction valve 41.吹除阀 Sea chest cleaning valve 42.防浪阀 Storm valve 43.舱壁阀 Bulkhead valve 44.快关阀 Emergency shut off valve 45.呼吸阀 Breather valve 五、泵类(Words about pump) 1.电动泵 Motor-driven pump 2.柱塞泵 Plunger pump 3.叶片泵 Vane pump 4.回转泵 Rotary pump 5.齿轮泵 Gear pump 6.往复泵 Reciprocating pump 7.离心泵 Centrifugal pump 1.电动泵 Motor-driven pump 2.柱塞泵 Plunger pump 3.叶片泵 Vane pump 4.回转泵 Rotary pump 5.齿轮泵 Gear pump 6.往复泵 Reciprocating pump 7.离心泵 Centrifugal pump 8.真空泵 Vacuum pump 9.螺杆泵 Screw pump 10.喷射泵 Ejector pump 11.冷却泵 Cooling pump 12.淡水泵 Fresh water pump 13.海水泵 Sea water pump 14.给水泵 Feed water pump 15.循环泵 Circulating pump 16.锅炉给水泵 Boiler feed pump 17.卫生水泵 Sanitary pump 18.压载泵 Ballast pump 19.舱底泵 Bilge pump 20.污水泵 Sewage pump 21.燃油泵 Fuel pump 22.高压油泵 High pressure pump 23.底压油泵 Low pressure pump 24.驳运泵 Transfer pump 25.增压泵 Booster pump 26.消防泵 Fire pump 27.通用泵 G.S. pump 28.旋涡泵 Regenerative 29.蜗壳泵 Volute pump 30.导叶泵 Diffuser pump 31.单联泵 Simplex pump 32.双联泵 Duplex pump 33.多联泵 Multiplex pump 34.活塞泵 Piston pump 35.减摇泵 Anti-roll pump 36.总用泵 General service pump 37.应急消防泵Emergency fire pump 38.扫舱泵 Stripping pump 39.货油泵 Cargo oil pump 40.滑油泵 Lubricating oil pump 六、甲板机械类(Deck machinery ) 1.锚机 Windlass 2.锚机轴 Windlass shaft 3.刹车带 Brake lining 4.离合器 Clutch 5.锚链轮 Anchor Chain wheel 6.轴承瓦 Bearing bush 7.轴承盖 Bearing cover 8.绞揽机 Capstan 9.系揽绞车 Mooring winch 10.卷缆车 Reel 11.钢丝绳 Wire rope 12.卡环 Shackle 13.缆绳 Mooring rope 14.滑轮 Block 15.刹车装置 Brake device 16.制链器 Anchor chain stopper 17.舱盖滚轮 Hatch cover wheel 18.舱盖铰链 Hatch cover hinge 19.液压油缸 Hydraulic jack 20.起货机 Cargo winch 21.可令吊 Crane 22.生活吊 Accommodation crane 23.吊杆 Derrick boom 24.桅杆 Mast 25.救生艇 Lifeboat 26.艇架 Davit 27.艇机 Lifeboat capstan 28.救生筏 Life raft 29.救生衣 Life jacket七、工具类(Word about tools)1.车床 Lathe2.刨床 Planing machine3.钻床 Drill machine4.砂轮机 Grinding machine5.磨床 Grinder6.铣床 Milling machine7.镗床 Boring machine8.手锤Engineer’s hammer9.冲击板手 Impact wrench10.板手 Spanner11.活络板手 Screw spanner12.梅花板手 Ring spanner13.呆扳手 Open spanner15.套筒板手 Socket spanner16.管子钳 Pipe spanner17.螺丝刀 Screw driver18.钢丝钳 Wire pliers19.尖嘴钳 Long nose pliers20.钢锯 Hack saw21.剪刀 Scissors22.手电筒 Torch23.扁铲(凿子) Chisel24.锉刀 File25.丝攻 Thread tap26.板牙 Thread die27.绞刀 Reamer28.刮刀 Scraper29.油石 Oil stone30.拔子(拉马) Puller31.沙布 Emery cloth32.破布 Rag33.卷尺 Measuring tape34.空心冲 Hole punch35.样冲 Joint punch36.油壶 Oil gun37.牛油枪 Grease gun38.手电钻 Handle drill39.钻头 Drill40.液压千斤 Hydraulic jack.41.塞尺 Feeler gauge42.游标卡尺 Vernier caliper43.外卡尺 Outside calipers44.内卡尺 Inside calipers45.螺纹量规 Screw gauge46.桥规 Bridge gauge47.电焊机 Electrode welding machine 48.气焊机 Gas welding machine49.电焊钳 Electric welding pliers 50.气割枪 Cutting touch51.电焊条 Electric soldering iron 52.电工刀 Electrician knife53.电笔 Test pen54.剥线钳 Wire stripping pliers 55.圆规 Compass56.量表 Gauge57.拐档表 Crank deflection gauge 58.深度规 Depth gauge59.千分表 Micrometer gauge60.台虎钳 Table vice61.柴油 Diesel oil62.滑油 Lubricating oil63.液压油 Hydraulic oil64.重油 Heavy oil65.燃油 Fuel oil66.黄油 Grease67.螺栓 Bolt68.螺帽 Nut69.垫片 Washer70.研磨沙 Grinding sand71.研磨膏 Grinding paste72.石棉板 Asbestos plate73.青壳纸 Fish paper74.盘根 Packing75.细钢丝 Thin steel wire76.密封圈 Rubber seal ring 77.塑料管 Plastic pipe78.胶皮管 Rubber hose79.电灯泡 Electric bulb80.工作灯 Working lamp81.插头 Electric plug82.插座 Electric socket.93.喷砂机 Sand blaster outfit94.空气马达 Air motor95.油柜清洁器 Tank cleaning machine96.高压冲水机High pressure hose forhydraulic97.真空泵 Vacuum pump98.套筒扳手组 Socket wrench set99.深头套筒 Deep socket wrench100.套筒扳手 Box wrench101.单开口扳手 Single open end wrench102.双开口扳手 Double open end wrench103.转矩扳手 Torque wrench104.电动机扳手 Motor wrench105.侧剪钳 Slide cutting plier106.活节钳 Combination plier107.可调快速扳手Speed wrench108.螺丝起子 Screwdriver109.偏向螺丝起子Offset screw110.六角螺帽起子组Hexagon nut drivers set111.手摇钻 Straight hand drill112.手工锯 Hacksaw frame113.锯片 Hacksaw blade114.砂纸 Silicon paper115.手拉葫芦 Chain block116.高压管 High pressure hose117.液压千金顶 Hydraulic jack118.锤子 Hammer119.平錾 Cold chisel120.活动扳手 Adjustable wrench121.螺丝刀 Screwdriver122.侧剪铗 Side cutting hipper123.螺栓剪 Cable cutter124.敲击管钳 Rap wrench125.砂轮 Grinding wheel126.老虎钳 Utility vise127.直梯 Straight ladder128.踏梯 Step ladder129.平台推车 Platform trunk130.搬平车 Gas cylinder carrier131.给油机 Grease lubricator132.强力油泵 Heavy duty pump oiler133.油壶 Oil jag134.麻花钻 Twist drill135.绞刀 Pin reamer136.旋转中心钻Rolling center137.外径测微计Outside micrometer withcounter138.六折式尺 Six-folding rule139.弹性带尺 Convex rule140.不锈钢直尺 Stainless steel straightrule141.平面规 Surface gauge142.平行直角定规Precision flat try square143.温度计 Thermometer八、常用物料(Material in common use)1.阀研磨剂 valve grinding compound2.电焊条 steel electrode3.气焊条 Steel welding wire4.细钢丝绳 Seizing wire5.刚焊条 Steel welding rod6.紫铜管 Copper tube7.乙炔气瓶 Acetylene cylinder8.木屑 Saw dust9.水泥 Cement10.石灰 Lime11.帆布手套 Canvas glove12.垫片 Gasket.13.氧气瓶 Oxygen cylinder14.抹布 Rag15.垫隙片 Shim16.电线 Wire17.电缆 Electric cylinder18.电池 Rag19.灯泡 Bulb20.胶布 Insulating tape21.插头 Plug22.插座 Socket23.保险丝 Fuse24.不锈钢 Stainless steel25.铸铁 Cast iron26.黄铜 Brass27.青铜 Bronze28.铝合金 Aluminium alloy29.橡胶 Rubber30.石棉 Asbestus31.低碳钢 Soft steel32.高碳钢 High-carbon steel33.合金钢 Alloy steel34.木材 Wood35.塑料 Plastic36.球墨铸铁 Nodular iron九、常用紧固件(Part of fixation in common use)1.螺栓 Bolt2.螺丝 Screw3.螺母 Nut4.方头螺栓 Sq head bolt5.埋头螺栓 Counter sunk head screw6.套筒螺栓 Socket head bolt7.定位螺栓 Set screw8.十字接头 Cross9.锥形销 Taper pin10.锁紧螺母 Lock nut11.六角头螺栓 Hex head bolt十、常用油类(Oil in common use)1.汽油 Gas oil2.煤油 Kerosene3.润滑油 Lubricating oil4.汽缸油 Cylinder oil5.压缩机油 Compressor oil6.齿轮油 Gear oil7.机油 Motor oil8.凡士林 Vaseline9.燃油 Fuel oil10.油脂 Grease11.柴油 Diesel oil十一、常用量词(Quantifier in common use)1.件,只,个 Piece2.条,张,片 Sheet3.双 Pair4.套,组,副 Set.5.盒 Box6.箱 Case7.瓶 Bottle8.米 Meter9.厘米 Centimeter10.毫米 Millimeter11.公斤 Kilogram12.克 Gram13.公升 Liter14.平方 Square15.袋 Bag16.码 Yard17.吨 Ton18.磅 Pound19.加仑 Gallon20.立方 Cubic十二、国家名称(Name of country)1.中国 China2.美国 American3.日本 Japan4.英国 Britain5.法国 France6.德国 German7.韩国 South Korea8.希腊 Greece9.泰国 Thailand10.印度 India11.挪威 Norway12.俄罗斯 Russia13.新加坡 Singapore14.澳大利亚 Australia15.伊朗 Iran16.丹麦 Denmark17.加拿大 Canada18.丹麦 Denmark19.芬兰 Finland20.巴基斯坦 Pakistan21.意大利 Italy十三、常用缩语(abbreviation in common use) 1.主机 M/E2.付机 A/E3.阀 V/V4.泵 P/P5.备车 St/by6.完车 F.W.E.7.前进三 FAHD8.微速后退 D.S.Ast9.前进二 H.Ahd10.高压 H.P.11.低压 L.P.12.重油/柴油 H.O./D.O.13.前后 F/A14.左舷 P: port15.无人机舱 UMS16.自动 Auto17.气缸 Cyl18.燃油柜 19.滑油柜 20.沉淀柜 .21.排出 Disc22.吸入 Suct23.柴油柜 十四、船用动态常用单词(marine tends word) 1.停靠 Alongside2.接近 Approach3.停泊 Berth4.浮筒 Buoy5.码头 Pier6.港口 Port7.移泊 Shift8.航次 Voyage9.试验 Try10.值班 Watch11.航行 Sail十五、船舶机电设备操作词汇(manipulate of marine equipment) 1.调整 Adjust2.压载 Ballast3.转换 Change over4.清洁 Clean5.联接 Connect6.排放压载 Deballast7.放残水 Drain8.卸载 Off9.油漆 Paint10.接通 Put on11.吹灰 Soot blown12.开始 Start13.顶端 Top14.洗 Wash15.吹 Blow16.检查 Check17.铲 Chip18.断开 Cut out19.排放 Discharge20.除垢 Descale21.检验 Examine 22.受载 On(load)23.用泵排出 Pump out24.调整 Set25.停止 Stop26.调驳 Transfer27.加满 Top up十六、故障常用单词 (words about malfunction)1.失常的 Abnormal2.烧坏 Burn3.堵塞 Clog4.裂缝 Crack5.变形 Deform6.毁坏 Destroy7.磨损 Wear8.出故障 In trouble9.敲击 Knock10.松开 Loose11.不对中 Misalign12.不足的 Insufficient13.失灵 Out of order14.过载 Overload15.过度磨损 Over-worn16.尺寸过大 Oversized17.尺寸过小 Under-sized18.振动 Vibrate19.不平的 Uneven20.不准确 Inaccurate21.全船断电 Black out22.出故障 Fail23.关掉 Shut off24.弯曲 Bend25.停车 Break drown26.腐蚀 Corrode27.腐蚀的 Corrosive28.损坏 Damage29.有毛病的 Faulty30.有缺陷的 Defective31.破裂 Fracture32.卡住 Jam33.漏泄 Leak34.漏泄的 Leaky35.融化 Melt36.噪声 Noise37.过热 Overheat38.咬住 Seize39.紧的 Tight40.松的 Loosen41.发现 Find42.停止 Stop43.脏的 Dirty44.油污的 greasy45.失效的 ineffective46.椭圆形的 oval47.点不着火 misfire48.接错 misjoin49.放错 misplace50.老化 perish51.麻点 pit52.凸起 ridge53.划伤 score54.拉痕 scuff十七、保养检修常用词汇(Words about maintain and examination)1.卡死 Blind2.用卡钳量 Caliper3.关闭 Close4.解体 Disassemble5.安装 Fix6.组装 Box up7.检验 Check8.拆卸 Dismantle9.装配 Fit10.紧固 Fasten11.测量 Gauge12.安装 Install13.测量 Measure14.打开 Open15.上油漆 Paint16.换新 Renew17.上紧 Tighten18.洗 Wash19.涂油脂 Grease20.松开 Loosen21.加油 Oil22.检修 Overhaul23.重新组装 Reassemble24.测取读数 Take reading25.拧开螺栓 Unbolt26.抽出 Withdraw十八、常用数字(Numeral in common use)一 One二 Two三 Three四 Four五 Five六 Six七 Seven八 Eight九 Nine十 Ten十一 Eleven十二 Twelve十三 Thirteen十四 Fourteen十五 Fifteen十六 Sixteen十七 Seventeen十八 Eighteen十九 Nineteen二十 Twenty三十 Thirty四十 Forty五十 Fifty六十 Sixty七十 Seventy八十 Eighty九十 Ninety百 Hundred千 Thousand万 Ten thousand百万 Million第一 First第二 Second第三 Third第四 Fourth第五 Fifth第六 Sixth第七 Seventh第八 Eighth第九 Ninth第十 Tenth第十一 Eleventh第十二 Twelfth第二十 Twentieth十九、时间、季节与方向(Time、Season and Direction)1.星期一 Monday2.星期二 Tuesday3.星期三 Wednesday4.星期四 Thursday5.星期五 Friday6.星期六 Saturday7.星期日 Sunday8.春季 Spring9.夏季 Summer10.秋季 Autumn11.冬季 Winter12.一月 January 13.二月 February 14.三月 March 15.四月 April 16.五月 May 17.六月 June 18.七月 July 19.八月 August 20.九月 September 21.十月 October 22.十一月 November 23.十二月 December 24.小时 Hour 25.分钟 Minute 26.秒 Second 27.月 Month 28.天 Day 29.夜 Night 30.周 Week 31.早晨、上午 Morning 32.下午 Afternoon 33.傍晚 Evening 34.正午 Noon 35.今天 Today 36.昨天 Yesterday 37.明天 Tomorrow 38.前天 The day before yesterday 39.后天 The day after tomorrow 40.本周 This week 41.上周 Last week 42.下周 Next week 43.九月十日 Sep.10th44.去年 Last year 45.明年 Next year 46.上周二 Last Tuesday 47.下周一 Next Monday 48.东 East 49.西 West 50.南 South 51.北 North 52.西北 Northwest 53.东北 Northeast 54.东南 Southeast 55.西南 Southwest 56.世纪 Century 二十、常用词组(Phrases in common use ) 1234.发现不正常 found out of order 5.发现不合标准 found not up to standard 6.发现不准确 found inaccurate 7.发现失去作用 found out of function 8.发现轧住 found seized 9.发现过热 found overheated 10.发现过度磨损 found excessive wear 11.发现过度磨掉 found worn out 12.发现有一点倾斜 found a little bit inclined 13.发现不正常 found abnormal 14. 发现因过热而损坏found destroyed by overheating 15.发现龟裂 found chapped 16.发现塌陷 found collapsed 17.发现运转失灵 found out of operation 18.发现呈椭圆形 found oval 19.发现拉痕 found scored 20.发现拉毛 found scuffed 21.发现变形 found deformed 22.发现松动 found loose 23.发现油污 found greasy 24.发现肮脏 found dirty 25.发现咬住 found stuck 26.发现挤压 found squeezed 27.发现弯曲 found bent 28.发现故障 found faulty 29.发现损坏 found damaged 30.发现破碎成片 found broken to pieces 31.发现部分剥离 found partly detached 32.发现部分堵塞 found partly choked 33.发现剧烈震动 found violent vibration 34.发现烧坏 found burnt 35.发现断裂 found fractured 36.发现接地 found earthed 37.发现敲缸 found knocking 38.发现溶化 found melted away 39.发现泄漏 found leaking (found leaky) 40.发现冻结 found stuck fast by icing 41.发现锈蚀 found rusty 42.发现失效 found ineffective 43.发现故障 found out of order 44.发现结霜 found frosted 45.发现丢失 found lost 46.发现出故障 found in trouble 47.发现失灵 found out of order 48.发现失灵 found out of action 49.发现不一致 found out of operation 50.发现错位 found out of place 二十一、常用动词和例句 (Verb in common use and example) 1.借 borrow 我要向你借这份图纸 I want to borrow the drawing from you. 我可以向你借这个手锤吗? May I borrow the hammer from you? 2.裂 break 阀杆断裂了 The valve spindle is broken. 滚动轴承断裂成碎片了 The ball bearing are broken to pieces. 3.加强 build up 叶轮应该堆焊 The impeller should be built up by welding. 4. 烧 burn 电动机烧了 The motor is burnt. 5. 进行 carry out 应进行负载试验 The load test should be carried out. 6.吹blow 管子必须用压缩空气吹清 The pipe should be blown with compressed air. 7.铸 cast 按原样铸造一个Cast one piece as per sample. 8.引起 cause 损坏是有剧烈振动引起的The damage was caused by violent vibration. 9.倒角 chamfer 油槽须倒角 Oil groove is to be chamfered. 法兰切削后须倒角The flange should be chamfered after being machined. 10.换掉 change 把它们换掉,否则我拒绝验收 Have them changed, otherwise I refuse to accept them. 11.龟裂 chap 轴瓦上的白合金龟裂了The white metal on the bearing bush is chapped. 12.核查 check 用桥规核查主轴承 Check the main bearing with bridge gauge. 修理前后要核查拐档Check the crankshaft deflection before and after repair. 13.清洁 clean 装前须清洁 Clean it before fit back. 14.阻塞 clog 燃油滤器阻塞了 The fuel filter is clogged. 15.涂漆 coat 用红丹涂管子 Coat the pipe with red lead. 泵壳里涂防护漆The pump casing is to be coated with anti-fouling. 16.完成 complete finish 你什么时候能完成修理工作? When can you complete (finish) the repair job? 17.连接 connect 把电动机和淡水泵连接起来 Connect the motor with the fresh water pump 18.腐蚀 corrode 泵壳和叶轮均有腐蚀The pump casing and impeller are corroded. 19.盖 cover 请把所有卸下的部件盖起来 Please cover all the removed parts. 20.裂 二号缸头裂开穿透至冷却水空间 No.2 cylinder head is cracked. 21.吊 crane 把液压马达吊上岸去修理 Crane the hydraulic motor ashore for repair. 22.割 cut 把底座割掉 Cut off the bedplate. 23.损坏 damage 滚动轴承严重损坏 The ball bearings are seriously damaged. 24.脱落 detach 白合金部分脱落了 The white metal is partly detached. 25.查看 detect 查看氟里昂系统有无泄漏 Detect the Freon system for leakage.26.解体 disassemble 解体,清洁并检查高压油泵Disassemble, clean and check the H.P. fuel pump. 27.脱开 disconnect 把起动空气管脱开 Disconnect the starting air pipe. 将发电机与原动机脱开。

船舶动力主要专业英汉词汇

船舶动力主要专业英汉词汇

主要专业词汇1、crew member船员2、captain船长3、chief engineer轮机长4、chief mate大副5、second engineer大管轮6、second mate二副7、third engineer二管轮8、third mate三副9、fourth engineer三管轮10、assistant engineer轮助11、electrical engineer电机员12、mechanic机工、机匠13、ship船舶14、diesel boat柴油船舶15、electric propulsion ship电力推进船16、lift on/off ship吊装船17、container ship集装箱船18、cargo ship货船19、dry cargo ship干货船20、harbor boat港作船21、passenger ship客船22、ore carrier矿砂船23、refrigerated cargo ship冷藏船24、multipurpose towing ship多用途拖船25、nuclear powered vessel核动力船26、steam turbine ship汽轮机船27、gas turbine ship燃气轮机船28、ocean-going ship远洋船29、oil water disposal boat油污水处理船30、oil tanker油船31、general cargo ship杂货船32、hull strength船体强度33、hogging中拱34、sagging中垂35、longitudiual rigidiy总刚度36、torsional strength扭转强度37、local strength局部强度38、shell plate外板39、hull structure船体结构40、transverse system of framing横骨架式41、longitudinal system of framing纵骨架式42、combination system of framing混合骨架式43、framing管架44、truss纵骨45、gorder纵行46、longitudinal纵骨47、single strake单板48、double bottom双层底49、bilge strake舭列板50、keel龙骨51、floor肋底52、frame肋骨53、frame spacing肋骨间距54、stern post尾柱55、stem首柱56、propeller strut尾轴架57、stern tube尾轴管58、shaft tunnel轴隧59、floating condition浮态60、buoyancy浮性61、heel横倾62、trim纵倾63、center gravity重心64、center offloatation漂心65、stability稳性66、metacenter稳心67、statical stability静稳性68、initial stability初稳性69、stability at large angles大倾角稳性70、rudder舵71、flat-plate rudder平板舵72、balanced rudder平衡舵73、streamline rudder流线型舵74、underhung rudder悬挂舵75、flag-type rudder襟翼舵76、steerine gear操舵装置77、anchor锚78、lightweight anchor大抓力锚79、admiralty anchor海军锚80、single-fluke anchor单爪锚81、stock anchor有杆锚82、anchor chain锚链83、chain cable compressor制链器84、mooring bitt带缆桩85、mooring cleat带缆羊角86、fairlead导缆器87、cargo handinggear起货设备88、derrick rig吊杆装置89、life boat救生艇90、unclosed lifeboat开敞式救生艇91、closed lifeboat封闭式救生船92、lifebuoy救生圈93、watertight door水密门94、sliding watertight door滑动水密门95、fire proof door防火门96、fuel oil system燃油系统97、tracer line伴热管98、fuel transfer pump驳运泵99、setting tank沉淀柜100、oil separator分油机101、oil collector集油柜102、daily service tank日用柜103、fuel comsumption rate燃油消耗率104、fuel booster pump燃油增压泵105、vent line透气管106、duplex filter unit双联滤器107、lubricating system润滑系统108、magnetic filter磁性滤器109、lube oil pump滑油泵110、lube oil cooler滑油冷却器111、lube oil drain tank滑油循环柜112、cylinder lubrication气缸滑油113、wet sump lubrication湿底滑油114、dry sump lubrication干底滑油115、oil sump油底壳116、cooling system冷却系统117、fresh water cooler淡水冷却器118、closed cooling water system闭式冷却119、fresh water cooler pump淡水冷却泵120、sea valve海底阀121、sea chest海底阀箱122、sea water strainer海水粗滤器123、expansion tank膨胀水箱124、heat exchanger热交换器125、operational code操作代码126、central cooling system中央冷却系统127、marine pollution prevention海洋防污染128、standard discharge connection标准排放接头129、standard shore connection标准通岸接头130、de-oiler除油器131、faecal coliform大肠杆菌132、shipboard marine pollution emergency plan(SMPEP)船舶海洋污染应急计划133、shipboard oil pollution emergency plan(SOPEP)船舶油污染应急计划134、pollution by garbage from ships船舶垃圾污染135、pollution by sewage from ships船舶生活污染136、shipboard incinerootion船上焚烧137、noise level on boardship船上噪音等级138、atmospheric pollution大气污染139、abandon ship弃船140、emergency equipment应急设备141、station bill应急部署表142、emergency bilge pump应急舱底泵143、emergency bilge suction应急舱底吸口144、emergency valve应急阀145、emergency battery应急蓄电池145、emergency generator应急发电机boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓,上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽,计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼,驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏,球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例,按约定cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容,载货容积cargo handling 货物装卸carriage 拖车,拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心,重心,质心,矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭,舷,脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室,粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计couple 力矩,力偶crane 克令吊,起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据,准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室,甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机,吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图,原理图,设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站,划分,分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力,拖拽力drainage 排水draught 吃水,草图,设计图,牵引力dredge 挖泥船drift 漂移,偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计,功率计e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力,供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度,高程,船型线图的侧面图,立视图,纵剖线图,海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力,全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配,安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮,渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边,法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘,外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型,流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件,锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨,框架,桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的,螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂,轴毂,套筒hull form 船型,船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖,通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水,浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的,加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点,交叉,横断(切)inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射,下水launch 汽艇launching equipmeng (向水中)投放设备LCC 大型原油轮leading edge 导缘,导边ledge 副梁材length overall 总长leveler 调平器,矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约,规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵(横)稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械(主机)卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的,海运的,靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构,抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱,垂直的,正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销,枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头,停泊所quotation 报价单racking 倾斜,变形,船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register (船舶)登录簿,船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂,恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接,铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺,尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面,横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切,剪力shear buckling 剪切性屈曲shear curve 剪力曲线。

船舶英语词汇大全

船舶英语词汇大全

船舶英语词汇大全一、船舶基本结构词汇1. 船体(Hull):船舶的主体部分,包括船壳、甲板和舾装。

2. 船壳(Shell):船体的外表面,起到防水、承重的作用。

3. 甲板(Deck):船舶的顶部平面,用于行走、作业和装载货物。

4. 舷窗(Porthole):船体两侧的窗户,用于通风和采光。

5. 舷梯(Jacob's ladder):连接船舶与码头的小梯子,便于人员上下船。

6. 舵(Rudder):控制船舶方向的装置,位于船尾。

7. 锚(Anchor):固定船舶位置的器具,用于抛锚停泊。

8. 船锚链(Anchor chain):连接船锚与船舶的链条。

9. 船舶龙骨(Keel):船体底部的一条纵向构件,起到支撑作用。

二、船舶动力装置词汇1. 船舶主机(Main engine):船舶的动力源,通常为柴油机或蒸汽轮机。

2. 船舶辅机(Auxiliary engine):为船舶提供辅助动力的装置,如发电机、空压机等。

3. 螺旋桨(Propeller):将主机产生的动力转化为推力的装置,位于船尾。

4. 柴油机(Diesel engine):以柴油为燃料的内燃机,广泛应用于船舶动力装置。

5. 蒸汽轮机(Steam turbine):利用蒸汽驱动叶轮做功的热力发动机。

6. 燃油喷射泵(Fuel injection pump):柴油机燃油系统中,将燃油高压喷射到燃烧室的装置。

三、船舶导航设备词汇1. 罗经(Compass):指示船舶航向的导航仪器。

2. 船用雷达(Marine radar):用于探测船舶周围水域障碍物的电子设备。

3. GPS导航仪(GPS navigator):全球定位系统导航设备,用于确定船舶位置和航迹。

4. 电子海图(Electronic chart):显示海域地理信息的电子地图。

5. 船舶自动识别系统(S):用于船舶识别、追踪和避碰的通信系统。

四、船舶通讯设备词汇1. 船用无线电(Marine radio):用于船舶与船舶、船舶与陆地之间通信的无线电设备。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

船体aircraft carrier 航母submarine 潜艇air cushion vehicle 气垫船longitudinal strength 总纵强度transverse strength 横向强度local strength 局部应力hull 主船体superstructure 上层建筑stem 船首midship 船中stern 船尾forecastle 首楼brige 桥楼poop 尾楼deck house 甲板室ship bottom 船底ship side 舷侧upper deck 上甲板lower deck 下甲板transverse bulkhead 横舱壁longitudinal bulkhead 纵舱壁forepeak bulkhead 首尖舱壁afterpeak bulkhead 尾尖舱壁shell plate 外板seam 边接缝butt 端接缝strake 列板bottom plate 底板plate keel 平板龙骨bilge strake 舭列板side plate 舷侧外板sheer strake 舷顶列板second deck 第二甲板third deck 第三甲板platform deck 平台甲板deck plate 甲板板deck stringer 甲板边板sponson deck 舷伸甲板center keelson 中内龙骨side keelson 旁内龙骨T-bar T型材web 腹板bracket 肘板face plate 面板flange 折边板floor 肋板bilge bracket 舭肘板bulb plate 球扁钢angle bar 角钢bottom center girder 中底桁bottom side girder 旁底桁solid floor 主肋板watertight floor水密肋板bracket floor框架肋板lightened floor 轻型肋板stiffener 加强筋reverse frame 内底横骨bottom frame 船底肋骨inner bottom plate 内底板man hole 人孔margin plate 内底边板duct keel 箱型中底桁pipe tunnel 管隧longitudinal 纵骨bottom longitudinal 船底纵骨inner bottom longitudinal 内底纵骨bottom side tank 底边舱foundation seating 基座shaft tunnel 轴隧tunnel recess 尾室emergency exit 应急出口bilge keel 舭龙骨frame 肋骨integrated barge 分节驳main frame 主肋骨tweendeck frame 甲板间肋骨intermediate frame 中间肋骨web frame 强肋骨side stringer 舷侧纵桁side longitudinal 舷侧纵骨cross tie 撑杆wing tank 舷边舱ballast water tank 压载水舱torsion box 抗扭箱bulwark 舷墙fender 护舷材beam 横梁deck beam 甲板横梁half beam 半梁hatch end beam 舱口端横梁deck girder 甲板纵桁hatch side girder 舱口纵桁beam knee 梁肘板deck longitudinal 甲板纵骨web beam 强横梁cargo hatch 舱口hatch coaming 舱口围板gusset plate 菱形板hatch side cantilever 悬臂梁piller 支柱topside tank 顶边舱excess hatch 人员出入舱口expansion trunk 膨胀井cofferdam 隔离空舱partial bulkhead 局部舱壁plane bulkhead 平面舱壁bulkhead plate 舱壁板tweendeck bulkhead 甲板间舱壁vertical bow 直立型首raked bow 前倾型首clipper bow 飞剪型首icebreaker bow 破冰型首bulb bow 球鼻型首fore peak 首尖舱collision bulkhead 防撞舱壁raised floor 升高肋板panting beam 强胸横梁wash bulkhead 制荡舱壁chain locker 锚链舱stem 首柱steel plate stem 钢板首柱combination cast and rolled stem 铸钢和钢板混合式首柱forged steel stem 锻钢首柱thruster 侧推器elliptical stern 椭圆型尾cruiser stern 巡洋舰型尾transom stern 方型尾after peak 尾尖舱shaft tube 艉轴管cant frame 斜肋骨cant beam 斜横梁stern frame尾柱rudder post舵柱propeller post 螺旋桨柱shoe piece 尾柱底骨propeller shaft strut 艉轴架A-bracket 人字架shell bossing 轴包套spectacle frame 眼镜形骨架accommodation deck 起居甲板boat deck 艇甲板navigation deck 驾驶甲板compass deck 罗经甲板compass plateform 罗经平台expansion joint 伸缩接头engine casing 机舱棚derrick post 桅柱derrick plateform 起货机平台tower post 塔式桅pressure hull 耐压舰体pressure structure 耐压结构non pressure structure 非耐压结构pressure conning tower 耐压指挥台pressure tank 耐压水舱pressure bulkhead 耐压舱壁oil ballast tank 燃油压载水舱conning tower sail 指挥台围壳exhaust valve 排气阀camshaft 凸轮轴crankshaft 曲轴crosshead 十字头connecting rod 连杆tie bolt 地脚螺栓轮机英语ashore 在岸上,陆地上shipchandler 船舶供应商saloon 大台,大厅,酒吧,展览会场,motorman 机工agent 代理cabin 舱室corridor 走廊brief discription 简短,简要的介绍domestic 国内的,家庭的|佣人,国货materials 材料installation 安装,装置marine diesel engine 船用柴油机horsepower 马力diesel 柴油cylinder 汽缸bore 钻孔,孔cylinder bore 缸径piston 活塞stroke 冲程,打击,笔画piston stroke 活塞冲程compressor 压缩机the oil-burning vertical type auxiliary boiler 立式燃油辅助锅炉automatic changover switch 自动转换开关marine animals and plants 海洋动植物compound 混合,化合物,混合物,妥协chemical compound 化学添加剂corrosive 腐蚀copper 铜aluminium 铝instruction manual 说明书Asian 亚洲人alien 外国的,相异的,性质不同的,外侨,转让the living expenditure 生活费用spare part 备件urgent 急切的,迫切的recall the order 取消订单surveyor 验船师leakage of fuel oil 漏油nozzle nap喷嘴帽injector 喷油器on the spot 现场B register of shipping B船级社bunkering 加油terminal 终点,终极oil company’s terminal 油品公司码头barge 驳船application 应用,申请store 储备,储藏high reputation 信誉好tempting 诱人的,吸引人的quote 引述,举证catalogue 目录bolt 螺栓freon 氟利昂brake 刹车expansion valve 膨胀阀air-mailed 空运Fax 传真whole threaded 全丝双头螺栓stud 大头钉screw pitch 螺距hexagon nipple 六角管接头washer 垫圈,洗涤器,洗衣人micrometer 千分表the wire stripping pliers 剥皮钳specification 规格invoice 发票tug 拖轮joint 接头the harbour office 港务局specific gravity 比重viscosity 粘度warranty 担保,保证,授权substitute 代替duplicate 复制,副本alongside 在旁边,在…旁边portside 左舷starboard 右舷hose 软管diameter 直径gangway 跳板,舷梯the fire hoses and equipment 消防管道和设备precaution 预防,警惕plug 塞住the deck scupper pipe 甲板排水管leakage泄露choke 窒息,堵塞dismantle 拆除tank 舱室trim 整齐,修整the temperature correction factor 温度修正系数acid number 酸值ash content 灰度main engine 主机fuel oil heater 燃油加热器pilot 引水员lube oil 滑油diesel oil 柴油revolution 旋转,革命,运行,循环the hydraulic valve 液压阀nitrogen 氮installation 安装,就职,装置the warm-up valve 暖缸阀the circulating lube oil tank 循环油柜filter 过滤器clamp 夹紧,固定住joint 垫子previous 以前的,早先的generator 发电机the prime mover 原动机liner 钢衬crack 裂缝turbochanger 涡轮增压器shift 轮班,移动,转变main air compressor 主空气增压器workshop 车间overtime work 加班foreman 工头the air cooler 空冷器abnormal noise 声音异常inlet/outlet 进口/出口supercharger 增压器the tube leakage 管子泄露the fouling脏堵the chemical cleaning equipment 化学清洗设备the air seal 气封felt 毡silencer 消音器disassembling 解体the cooling copper tube 冷却铜管the cooling ribs around the tube管上的散热翅片make-do with sth 凑合auxiliary engine 辅机cylinder 汽缸the cylinder head 缸头ground 研磨the inlet and exhaust valves 进排气阀trial 试验the end cover 端盖the valve seat 阀座piston ring活塞环crank 曲轴the crank bearing 曲轴轴承the oil sump 油底壳magnet 磁铁storekeeper 保管员the special tool 专用工具torque spanner 扭力扳手screw nut 螺帽loose 松的hydraulic tool 液压工具groove 槽the piston ring groove 活塞环槽gap 天地,缺口,空白machined 车削加工过storeroom 仓库the worn-out flare 磨损的喇叭口the bearing shell 轴承瓦the piston pin活塞销rag 破布bulletin 公告scraper ring 刮油环in triplicate 一式三份burr 毛刺crank bearing bushes 曲柄销轴瓦polish 抛光oilstone 油石oil sump 油底壳replenish the oil 加油the scavenger pressure 扫气压力the engine trial 试车surge喘振dismantle 拆卸fly-wheel 飞轮the up-side-down type 倒挂式oil filter 滤油器the indicator cock 示功考克crankcase 曲柄箱boiler 锅炉weld 焊接the blow-down pipe 排污管slope vessel 污水船the flue door 烟道drawing 图纸you can count on me 你可以放心the combustion chamber 燃烧室refractory line 炉墙peeled off 剥落high percentage of carbon 高含碳量the boiler automatic feed control 锅炉自动给水控制the combustion automatic control 燃烧自动控制low water level 低水位the light resistor 光敏电阻the ignition electrode 点火电极the ignition injector 点火油头the buoy for the water level control 水位控制浮子the scale is very thick 水垢很厚the relay for the high and low water levels高低水位接触器the insulating material of some wires was aged and peeled off 一些电线的绝缘层都易老化并脱落avometer 万用电表the solenoid valve 电磁阀flange法兰blind plate 盲板the oil way 油路scavenge the boiler 炉内扫气。

相关文档
最新文档