电子产品英文术语大全
电子产品常用英文词汇
电子产品常用英文词汇一、常见电子电气类英文单词1.功率power2.电压voltage3.电流current4.频率frequency5.效率efficiency6.波形waveform7.交流alternating-current8.直流direct-current9.适配器 adaptor10. 转换器 converter11. 逆变器 inverter12. 充电器 charger13. 控制器 controller14. 启动器 jump starter15. 器件device16. 元件component17. 电容器capacitor18. 电阻resistor19. 电感inductor20. 二极管diode21. 稳压二极管 zener22. 三极管audion23. 场效应管 MOSFEET(Metel-Oxide-Semiconductor Field Effect Transistor)24. 变压器 transformer25. 光藕 optical coupler26. 保险丝 fuse27. 半导体semiconductor28. 瓷片电容 ceramic capacitor29. 电解电容 electrolytic C30. 电感 inductance31. 电容 capacitance32. 电阻 resistance33. 感性的 inductive34. 容性的 capacitive35. 阻性的 resistive36. 阻抗impedance37. 纯正弦波 pure sine wave38. 修正正弦波 modified sine wave39. 方波 square wave40. 恒流源 constant current source41. 恒压源 constant voltage source42. 纹波电流 ripple current43. 涌入电流 inrush current44. 空载电流 no-load current45. 电网 power system46. 死区时间dead time47. 浮充电压 float charge voltage48. 正向电压forward voltage drop49. 续流二极管 freewheel diode50. 肖特基二极管 schottky51. 整流桥 bridge rectifier52. 超快速整流器 ultra fast rectifier53. 检测电阻 sense resistor54. 振荡电阻 timing resistor55. 散热片thermal slug/heat sink/ radiator56. 断路器breaker57. 过流保护器 circuit breaker58. 自由运行 free running59. 满负载 full load60. 过载 overload61. 轻载 light load62. 加载 upload63. 静态 static （state）64. 动态 dynamic （state）65. 稳态的 steady66. 静电 static electricity67. 电源调整率line regulation68. 负载调整率load regulation69. 满载效率 full load efficiency70. 最佳效率 optimum efficiency71. 输出效率 output efficiency72. 峰值效率 peak efficiency73. 标称效率 declared efficiency74. 视在功率 apparent power75. 有功功率 active power76. 无功功率 reactive power77. 功率因数 power-factor78. 耗散功率 power dissipation79. 空载损耗 no-load loss80. 关断状态 off state81. 电源工作电压 operating supply voltage82. 电压参考 voltage reference83. 参考值 reference value84. 反馈feedback85. 产品型号part number86. 掉电power down87. 上电power up88. 电源正常 power good89. 欠压锁定 under voltage lock out (UVLO)90. 上拉 pull up91. 下拉 pull down92. 上升沿 rising edge93. 下降沿 falling edge94. 上限 upper limit95. 下限 lower limit96. 极性 polarity97. 藕合 coupling98. 故障 malfunction99. 原理图 schematic diagram100. 封装footprint101. 设计流程 design cycle102. 设计余量 design margin二、常用电源类英文缩写SPS： switching power supplyPWM: pulse width modulationZCS： zero current switchingZVT: Zero Voltage TransitionPFC: Power Factor CorrectionRMS: Root mean square （均方根）THD: Total Harmonic Distortion (总谐波失真)OVP: Over Voltage ProtectionOCP: Over Current ProtectionOTP: Over Temperature ProtectionMCU: Micro Controller unitTVS: Transient voltage suppressorPCB: Printed circuit boardSMT: surface mounting technologyECR: Engineering Change RequestECN: Engineering Change noticeFMEA: Failure Mode Efficiency AnalysisIC: integrated circuitIE: Industrial EngineeringIT: information technologyAQL: Acceptable Quality LevelQA: Quality AssuranceQC: Qualty ControlIQC: Incoming Quality controlIPQC: In- process Quality control三、变压器类常用材料1. 磁芯：magnetic core2. 骨架：bobbin3. 导线：wire4. 绝缘胶带：insulation tape5. 挡带: margin tape6. 铜箔： copper foil7. 磁环： annular core8. 铁氟龙套管：teflon tube9. 绝缘套管：empire tuble10. 凡立水：varnish11. 气隙：gap12. 绕组：winding13. 初级绕组：primary coil14. 次级绕组：secondary coil15. 电感量: inductance16. 漏感： Leakage inductance17. 耐压：HI-POT18. 绝缘电阻: insulation resistance19. 匝数：turns四、工艺工程类常用英文词汇1. 技术规范：technical regulation2. 规范：specification3. 检修技术：service technic4. 焊接工艺：bonding technology5. 表面安装：surface mounting6. 元件面：component side7. 焊接面：solder side8. 元件孔：component hole9. 安装孔：mounting hole10. 工艺流程图：engineering flow sheet11. 故障指示：failure indication12. 锡焊： tin-lead bonding13. 装配：assembly14. 接插件：socket connector15. 连接器：connector16. 端子：terminal17. 端子壳：housing18. 插座：socket19. 插座盖：socket cover20. 点烟座：cigarette lighter socket21. 点烟头：cigar plug22. 接线座：wire holder23. 接线端子：wire connecting terminal24. 接线器：wire connector25. 线材规格：wire gauge26. 电烙铁： electric solding iron27. 烙铁头：solder horn28. 焊锡： soldering tin29. 焊盘： Pad30. 无铅： Lead Free31. 波峰焊：wave soldering32. 回流焊：reflow soldering33. 老化：burn-in/aging34. 极性： Polarity35. 正级：Positive pole36. 负极：negative pole37. 硬件:hardware38. 软件：software39. 通风孔：vent40. 支撑架/轴承：bearing41. 工艺：technics42. 夹具：fixture43. 冲压模具：die44. 注塑模具：injection mould45. 材料：material46. 扭矩：torque47. 应力：stress48. 强度:strength49. 机壳：enclosure50. 紧固件：fastener51. 螺栓：bolt52. 螺母：nut53. 螺丝：screw54. 垫片：washer55. 套筒扳手：socket key/ socket spanner56. 剪钳：wire cutter57. 剥线皮钳：wire stripper58. 裁线机：wire shear59. 防护罩：guard60. 环氧树脂:epoxy resin61. 玻璃纤维：glass fiber62. 光面：shiny side63. 粗糙面：matte side64. 处理面：treated sideTHANKS致力为企业和个人提供合同协议，策划案计划书，学习课件等等打造全网一站式需求欢迎您的下载，资料仅供参考。
电子产品常用英文词汇
电子产品常用英文词汇基础词汇Electronics (电子学): 研究电子设备、电路及其应用的科学。
Electronic device (电子设备): 任何使用电子元件来执行特定功能的设备，例如手机、电脑、电视等。
Circuit (电路): 由电子元件连接而成的路径，用于传输和控制电子信号。
Component (元件): 电路中的基本单元，例如电阻、电容、晶体管等。
Semiconductor (半导体): 导电性介于导体和绝缘体之间的材料，例如硅和锗。
Integrated circuit (集成电路): 将多个电子元件集成到一个芯片上的电路。
Microprocessor (微处理器): 执行计算机指令的集成电路。
Memory (存储器): 存储计算机数据的设备，例如 RAM、ROM、硬盘等。
Input device (输入设备): 将数据输入计算机的设备，例如键盘、鼠标、扫描仪等。
Output device (输出设备): 将计算机数据输出为人类可读形式的设备，例如显示器、打印机、扬声器等。
手机相关词汇Smartphone (智能手机): 集成了电话、计算机、相机等功能的手机。
Operating system (操作系统): 管理手机硬件和软件资源的系统，例如 Android、iOS 等。
App (应用程序): 在智能手机上运行的软件程序。
Battery (电池): 为手机提供电力的装置。
Camera (相机): 用于拍照和录像的设备。
Display (显示器): 显示手机信息的屏幕。
Speaker (扬声器): 将电信号转换为声音的装置。
电脑相关词汇Computer (电脑): 用于处理数据、存储信息和执行程序的设备。
Laptop (笔记本电脑): 便携式电脑。
Tablet (平板电脑): 介于手机和笔记本电脑之间的便携式设备。
Motherboard (主板): 连接电脑各个组件的电路板。
CPU (中央处理器): 执行电脑指令的芯片。
电子行业专业词汇术语(专业超全)
电子行业专业词汇术语GRR Gauge Repeatability Reproducibility 量测的再现性与再生性FPI First Piece Inspection 首件检查Sampling without replacement 不放回抽样SQA: Source(Supplier) Quality Audit 供货商品质审核1. QC : quality control 质量管理2. IQC : incoming quality control 进料质量管理出货质量管理3. OQC : output quality control4. PQC : process quality control 制程质量管理也称IPQC : in process quality control .允收标准5. AQL : acceptable quality level客户品质保证6. CQA: customer quality assurance7. MA : major defeat 主要缺点8. MI : minor defeat 次要缺点9. CR :critical defeat 关键缺点10. SMT : surface mounting technology 表面粘贴技术表面粘贴程序11. SMD :surface mounting device表面粘贴组件SMC : surface mounting component12.ECN : engineering change notice 工程变更通知13.DCN : design change notice 设计变更通知装配印刷电路板14.PCB : printed circuit board 印刷电路板16. BOM : bill of material 材料清单15.PCBA : printed circuit board assembly17. BIOS : basically input and output system18. MIL-STD-105E : 美国陆军标准 , 也称单次抽样计划 . 19. ISO : international standard organization 国际标准化组织20. DRAM: 内存条 21. Polarity :电性 22. Icicles : 锡尖 23.Non-wetting : 空焊25. Missing component : 缺件 26. Wrongcomponent : 错件准操作流程37. SIP : standard inspection process 38 .The good and not good segregation : 39. OBW : on board writer 熸录 BIOS40 . Simple random sampling : 简单随机抽样 直方图42 . Standard deviation :标准差43. CIP : Continuous improvement program持续改善计划27 . Excess component : 多件 28. Insufficient solder : 锡少 29 . Excessive solder : 锡多 30. Solder residue: 锡渣 31. Solder ball : 锡球 32. Tombstone : 墓碑 33 . Sideward ：侧立 34. Component damage : 零件破损 35. Gold finger: 金手指 36.SOP: standard operation process44. SPC : Statistical process control 制程统制 45 .基本输入输出系统24. Short circuit : 短路 标准检验流程 良品和不良品区分41. Histogram :16. BOM : bill of material 材料清单Sub-contractors : 分包商46. SQE: Supplier quality engineering sample : 抽样计划48. Loader : 治具质量追查系统50. Debug : 调试52. Inventory report for : 工时预算54. Calibration : 校验号56. Corrugated pad : 波纹垫盒58. Outer box : 外包装箱60. Sum of square : 平方和62. Conductive bag : 保护袋maintenance : 预防性维护64. Base unit : 基体66. Probe : 探针68. Golden card : 样本卡诊断程序70. Frame : 屏面47. Sampling49. QTS: Quality tracking system51. Spare parts: 备用品库存表53. Manpower/Tact estimation55. S/N :serial number 序57.Takeout tray: 内包装59. Vericode : 检验码61. Range : 全距63. Preventive65. Fixture : 制具67. Host probe : 主探针69. Diagnostics program :71. Lint-free gloves : 静值74. Related department : 相关部门75. lifted solder 浮焊76.plug hole 孔塞77. Wrong direction 极性反ponent damage or broken 零件破损79.Unmelted solder熔锡不良80.flux residue 松香未拭81.wrong label or upside down label 贴反82. mixed parts 机种混装83. poor solder mask 绿漆不良84. oxidize 零件氧化85.stand off height浮高86. IC reverse IC 反向87.supervisor课长88. Forman 组长89. WI=work instruction作业指导90. B.P. 非擦除状态91. Internal notification:内部联络单92. QP:Quality policy 质量政策93. QT: Quality target 品质目标94. Trend: 推移图95.Paret 柏拉图72 .Wrist wrap : 静电手环73. Target value : 目标96. UCL: Upper control limit 管制上限97.LCL:Lower controllimit 管制下限 100. PPM:Parts per million 单位不良率 102.Resistor: 电阻 104. Resistor array : 排阻 排容 106. DIODE: 二极管 108. Crystal: 震荡器 110.Bead: 电感 inductance 不良率 101.DPU:103.Capacitor:105. Capacitor array:112.ADM: Administration Department Engineering 零件工程 114. CSD :Customer Service Department Design 工业设计 116.IE: Industrial Engineering Relationship 工业关系 118. ME: Mechanical Engineering 119. MIS :Management Information Man ageme nt 资材 121. PCC: Project Coordination/Control 122. PD: Production Department 生产部 107.SOT:109.Fuse: 111.Connector: 行政单位 客户服务部 工业工程机构工程 System 信 息 部 专案协调控制Defects per unit电容三极管保险丝联结器113. CE: Component115. ID: Industrial117. IR: Industrial120. MM: Material123. PE: ProductEngineering 产品工程 124. PM: Product Manager 产品经理 125. PMC:Production Material Control生产物料管理126. PSC: Project Support & Control 产品协调127. Magnesium Alloy: 镁合金128. Metal Shearing: 裁剪129. CEM:Contract Electronics Manufacturing 电子制造服务企业EMS: Electronics Manufacturing Services130. ERP: Enterprise Resource Planning 企业资源规划SCM+CRM+ERP+EAI=Network direct TM links procurement, production, Logistics and sales采购, 生产, 后勤管理及市场营销的融合EAI: Enterprise application Integration 企业应用系统整合CRM: Customer Relationship Planning 客户服务规划SCM : Supply chain management 供应链管理131. OJT: On job training 在职培训132.Access Time:光盘搜寻时间133. B2CEC:Business to consumer electronic commerce 企业对消费者的电子商务B2BEC:Business to business electronic Commerce 企业间的电子商务L:Copper Clad Laminate 铜箔基板135. Intranet: 企业内部通讯网路136. ISP: Internet Service Provider 网络服务提供者ICP: Internet Content Provider 网络内容提供者137. GSM: Global System for Mobile Communication 泛欧数字式行动电话系统GPS: 全球卫星定位系统 138. Home Page: 网络首页 件 140. HTML: 超文标记语言 称 142. IP: 网络网域通讯协议地址 算机 139.Video Clip:141.Domainname:143.Notebook: 144. VR: Virtual Reality 虚拟实境 145. WAP: Wireless Application Protocol 146. LAN : Local area network 局域网络 WW World Wide Web 世域网 WAN: Wide Area Network 广域网络147. 3C: Computer, Communication, Consumer electronic 费性电子三大产品的整合 rmation Supplier Highway: 信息高速公路 149.UPS:Uninterrupted power system 不断电系统 无线应用软件协议计算机 150.Processed 影像文网域名笔记型计通讯 , 消material:流程性材料 151.Entity/Item: 实体 环 153.Quality losses: 质量损失 纠正措施152.Quality loop: 154.Corrective action:质量177.ISA: Industry Standard Architecture 工业标准结构178. EISA: Extended Industry Architecture 扩 展 工 业 标 准 结 构155. Preventive action: 预防措施 156.PDCAlan/Do/Check/Action 计划 /实施/ 检查/处理 157. Integrated circuits(IC): program: 应用程序 159.Utilities: 实用程序 storage:; 辅助存储器 161.Silicon chip: 硅片 驱 集成电路 158.Application160.Auxiliary storage/Second162Diskette drive:163.Display screen/Monitor: 显示器 164.Foreground: 前面 165.Montherboard: 母板 166.Mermory board: 内存 167.Slot: 插槽 168.Busata-bus/address-bus/Control bus: 总线 / 数据总线 / 地址总线 / 控制总线 169.Plotter: 绘 图 170.MPC:Multimedia personalcomputer 多媒体 171.Oscillator: 振荡器 动终端 ( 出纳) 机 173.Joystick port: 控制端口 示卡 172.Automatic teller terminal:174.VGA: Video Graphics Array175.Resolution: 分辨率 176.Register: 寄存器179. Adapter: 适配器 180. Peripheral: 外部设备 制解调器181. NIC:Network interface card 网络接口卡 182. SCSI: Small computer system interface183. VESA: Video Electronic Standards Association184. SIMM: Single in-line memory module 单 排 座 存 储 器 模 块 （ 内 存 条 ） 185. Casing: 外箱186. Aluminum: 铝质 187.Ceramic: 陶瓷的 188.Platter: 圆 盘片 189.Actuator: 调 节 器 190.Spindle: 轴 心 191.Actuation arm: 存取臂 192.Default code: 缺 省 代 码 193.Auxiliary port: 辅 助 端 口 194. Carriage return : 回车 195.Linefeed: 换行197.Video analog: 视频模拟196. ASCII: American Standard Code for Information Interchange 美国信息互 换标准代码198.TTL: Transistor- Transistor logic 199.Three-prong plug: 三芯电插头 连接插座201.Floppy disk: 软盘出电平181.Faxmodem:晶体管 -晶体管逻辑电路200.Female connector:202.Output level: 输203.Vertical/Horizontal synchronization: 场/行同步204. H(Horizontal)-Phase: 行相位205. Compatible: 兼容机206.Hardware Expansion Card: 硬件扩充卡207.Buffer: 缓冲208.CRM:Customer relationship Management 客户关系管理209.WIP: Work in process 半成品210.Waiver: 特别采用211. CX0系列一CEO: Chief Executive Office 首席执政官；执行总裁COO: Chief Operating OfficeCFO: Chief Finance OfficerCBO: Chief Business OfficerCTO: Chief Technology OfficerCIO: Chief Information OfficerCGO: Chief Government Officer212. NASDAQ: 纳斯达克证券市场NASDAQ Automated Quotation system213. VC: Venture Capital 风险投资214. PDA: Personal Date Assistant 个人数字助理PLA: Personal Information Assistant 个人信息助理215. PPAP: Advanced Product Quality Planning and Control Plan 生产性零组件核准程序216. FMEA: Potential Failure Mode and Effects Analysis失效模式与效应分析217. MSA: Measurement Systems Analysis 量测系统分析225. EMS: Electronics Manufacturing Supply-chain 226. Cause & Effects charts230. PDPC: Process Decision Program Chart System Chart 系统图法231. Relation Chart 关边图法 Matrix Chart 矩阵图法 232. Matrix Data Analysis 矩阵数据分析法234. Brain-storm 脑风暴法 JIT: Just In Time: 及时性生产模拟 235. Deming Prize: 戴明奖 Prototype 技术试作 236. BPM: Business Process Management业务流程管 MBO 目标管理218. QAS: Quality System Assessment 质量系统评鉴219. Cusum:计总合图220. Overall Equipment Effectiveness设备移动率221. Benchmarking: 竞争标杆 Analysis of motion/Ergonomics 动作分析 /人体工程学222. Roka Yoke 防错法MCR: machine capability ratio机器利用223. Mistake Proofing 防呆法 Taguchi methods 田口式方法 224, Vertical integration垂直整合 Surveillance定期追踪审查特性要因图 227. Scatter: 散布图Fool-Proof System防呆系统228. VE: Value Engineering价值工程 QFD: Quality Function Development质量机能展开229. Arrow Chart 箭头图法 Affiliate Chart亲和图法237. MBP: 方针管理FTA: 故障树分析QSC服务质量238. IPPB: Information 情况planning 策划Programming 规划Budget 预算239. EQ: Emotion Quotient: 情商IQ: Intelligence Quotient: 智商240. Implied Needs: 隐含要求Specified Requirement: 规定要求241. Probation: 观察期Incoming Product released for urgent production 紧急放行242. Advanced quality planning 先进的质量策划243. AOQ: Average Outgoing Quality 平均检出质量AOQL: Average Outgoing Quality Limit 平均检出质量界限244. Approved Supplier List 经核准认可的供应商名单245. Attribute date 特征Benchmarking 基准点Calibration 校准246. Capable process 工序能力Capability Index 序能力指数Capability ratio 工序能力率247. CHANG CY CLE TIME修改的时间周期Con ti nuous improveme nt 持续改进248. Control plans 控制策划Cost of quality 质量成本249. Cycle time reduction 减少周期时间250. Design of experiments 实验设计Deviation / Substitution 偏差/ 置换270. Material review board原材料审查部门MCR: machine capability251. ESD: Electrostatic discharge 静电释放252. EH&S: Environmental, Health, and Safely环境 , 健康 . 安全253. ESS: Environmental Stress Screening 环境应力筛选 254. FMEA: Failure Mode Effect Analysis 失误模式效应分析255. First Article approval 产品的首次论证 256. First pass yield一次性通过的成品率257. First sample inspection第一次样品检验258. FMECA: Failure mode effect and critically analysis 失误模式 , 效应及后果分析259. Gauge control 测量仪器控制260. GR&R: Gauge repeatability and reproducibility 测量仪器重复性和再现性261. HALT: Highly Accelerated Life Test 262. HAST: Highly Accelerated Stress Test 263. IN-CONTROL PROCESS 受控制工序 264. INDUSTRIAL AVERAGE 工业平均数 265. JIT (just in time) manufacturing characteristic 关健特征267. Key component 关健构件 268. Life Testing 寿命试 验 269. Lot traceability 批量可追溯性高加速寿命试验高加速应力试验( 实 时) 制 程 266. Keyratio 机械能力率271. NONCONFORMAN不符合272. OUT-OF-CONTROL PROCESS 失控工序273. Pilot Application 试产(试用) 274. PPM: Parts per million百万分之一275. Preventive VS detection 预防与探测Preventive maintenance 预防维护276. Process capability index 工序能力指277. Process control 工序控制278. Process improvement 工序改进279. Process simplification 过程简化280. Quality Clinic Process Chart (QCPC) 281. Quality information system手册283. Quality plan 质量计划策划统计质量控制质量诊断过程图质量资料体系282. Quality manual 质量284. Quality planning 质量285. Quality policy 质量方针286. Quality system系质量体288. Skill Matrix 技能表289. Statistical quality control (SQC) 290. Teamwork 团队工作291. Total quality management 全面质量管287. Reliability 可靠性RUN Chart 趋势表292. Variable data 变量数据293. Variation 影响变量294. Value Analysis 值分析295. Visual Factory 形象化工厂296. Survey Instructions 调查指引297. Profile 概况298. Improvement Plan 改进计划299. Evaluation 评估300. implementation 实施301. Compliance 符合302. Supplier Audit Report 供方审核报告303. Site Audit 现场审核304. Typical agenda 典型的议事日程305. Internal and external failure costs 内部和外部的失误成本306. Failure rate percentage 失误百分率307. Productivity (output /input) 生产率(产出/ 投入)308. Customer complaints 客户投诉309. Customer satisfaction indices 客户满意度指数310. Root cause analysis of failures 失误根原分析品管中英文名词对照表Accuracy 准确度Active 主动Action 评价. 处理Activity 活动Add加Addition rule 加法运算规则Analysis Covariance 协方差分析Analysis ofVariance 方差分析Appraisal Variation 评价变差Approved 承认ASQC 美国质量学会Attribute 计数值Audit 审核Automatic database recovery 数据库错误自动回复Average平均数Data Collection 数据收集Data concentrator 资料集Body 机构Brainstorming Techniques 脑力风暴法 Business Systems Planning 企业 系统规划 Cable 电缆 Capability 能力 Cause and Effect matrix 因果图 . 鱼骨图 Center line 中心线 check 检查 Check Sheets 检查表 Chi-squareDistribution 卡方分布Clutch spring 离合器弹簧 Coining 压印加工 Common cause 共同原因plan 管制计划Correction 纠正 Correlation Methods 低成本CPI: continuouse Process Improvement 连续工序改善 Creep 渐变 Cross Tabulation Tables 交*表CS: customer Sevice客户中心Cushion 缓冲 Customer 顾客 DSA: Defects Analysis System缺陷分析系统 Data 数据balance 平衡 Balance sheet资产负债对照表 Binomial 二项分配Complaint 投 诉 Compound factor 调 合 因 素 Concept 新 概 念Condenser 聚光镜Conformity 合格 Connection关联 Consumer ' s risk 消费者之风险Control 控制 Control characteristic管制特性 Control chart管制图 Control相关分析法 Cost down 降Data Collection 数据收集 Data concentrator 资料集Grade 等级Gum-roll橡皮滚筒Health meter体重计中缓存器DCC: Document Control Center文控中心Decision 决策. 判定Defects per unit 单位缺点数Description描述Detection 难检度 Device装置Digital 数字Do 执行DOE: Design of Experiments 实验设计Element—\ 元素Else 否则 Engineeringrecbnology 工程技术Entropy 函数 Environmental 环境Equipment 设备 Estimated accumulative frequency 计算估计累计数 E Equipment Variation设备变异 Event 事件External Failure 外部失效 , 外部缺陷 FA: Failure Analysis 坏品分析Fact control 事实管理 Fatique 疲劳FMEA:Failure Modeand Effect analysis 失效模式与效果分析 FPY 合 格率FQA: Final Quality Assurance 最终品质保证 FQC: Final Quality control 最终品质控制 Full-steer 完全转向 function 职能 Gauge system 量测系 统法运算规则Heat press 冲压粘着 Histogram 直方图 Hi-tech 高科技hypergeometric 超几何分配 hysteresis 磁滞现象 Improvement 改善 Inductance 电感 审查Information信息 Initial review 先期Inspection 检验Internal Failure 内部失效 , 内部缺陷IPQC: In Process Quality Control 制程品质控制 IQC: Incomming Quality Control来料品质控制IS International Organization for Standardization 国际标准组织 Law of large number 大数法则 Link 连接LCL: Lower Control limit 管制下限 产线品质控制LQC: Line Quality ControlLSL: Lower Size Limit 规格下限Machine 机 械 Manage 管 理Materials 物 料 Measurement 量 测Median 中位数Miss feed 漏送 Module,sub-system,sub-unit 单位 Momentum 原动力 Monte garlo method 原子核分裂热运动法 MSA: Measurement System Analysis量测系统分析 Multiplication ruleNIST 美国: 标准技术院 Normal 常态分布 Occurrence 发生率On.off system 开 , 关 系 统Operation Instruction 作 业 指 导 书Organization 组织 Parameter 参数Parto柏拉图Parts零件 Parts per品质工程Repair 返修million 不良率Passive 消极的 , 被动的 Plan 计划 Pulse 针脉冲 Policy 方Population 群体Power力量, 能源PQA: Process Quality Assurance制程品质保证Practice 实务Precision 精密度 preemptive 先占式多任务 Pressure 压缩Prevention 预防Probability机率Procedure 流 程Process 过程Process capability analysis制程能力分析图Process control and process capability 制程管制与制程能力Producer ' s risk 生产者之风险 Product 产品 Production生产Program 方案 Projects Assurance 品质保证 项目 QA: QualityQC: Quality Control 品质控制QE: Quality EngineeringQFD: Quality Function Desgin 品质机能展开 Quality质量Quality manual 品质手册 Quality policy 品质政策 Random experiment 随机试验 Random numbers随机数Range 全距 Record记录 Reflow 回流Reject拒收Repeatusility 再 现 性Reproducibility再生性Probability density function机率密度函数SOP: Standard Operation Procedure 标准作业书 SPC: Statistical Process Control 统计制程管制Special cause 特殊原因 Specification 规范SQA: Source(Supplier) Quality Assurance 供 货 商 品 质 保 证 Stage sampling 分段随机抽样Standard Deviation 标准差 Sum of squares 统计表 supplier 平方和 Residual 误 差Responsibilities 职责Review 评审Reword返工yield 直通率RPN: Risk Priority Number 风险系数Response 响 应Robustness 稳健性 Rolledsample抽样 , 样本Sample space 样本空间 放回抽样Sampling with replacementSampling without peplacement 不放回抽样析Scrap 报废 Screw 螺旋 Severity 粒冲击平面法Scatter diagram 散布图分严重度 Shot-peening 微Simple random sampling 简单随机取样 Size 规格 SL: Size Line规格中心线 Slip 滑动Stratified random sampling 分层随机抽样System 供方systematic sampling系统 , 体系StatisticalRequirement 要求7 Bottom FET Bottom FET 8 bucket capcitor 桶形电容tables 系统抽样TQM: Total Quality Management 全面品质管理 Traceablity 追溯 Training 培 训 Transaction processing and logging 交 易 处理Trouble 困扰Variance 变异和Customer 客户需求VOE: Voice of Engineer 工程需 [ 转帖 ] 电子行业相关的英语词汇带隙电压参考Taguchi-method 田口方法 Technical piece 测试片Theory 原理 Time stamp 时间戳印Torque 转矩Total 求和 TQC: Total Quality Controlcommittees 技术委员会 TestTime-lag 延迟 Title全面品质控制Up and down 上和下 UCL: Upper Control Limit USL: Upper Size Limit规格上限 Validation管制上限确认 Variable 计量值Vector 向量 Verification验证 Version 版本 VOC: voice of1 backplane 背板 2Band gap voltage reference3 benchtop supply 工作台电源4 Block Diagram 方块图5 Bode Plot 波特图6 Bootstrap自举11 constant current source 恒流源 12 Core Sataration饱和13 crossover frequency 交叉频率 14 current ripple 纹波电流 15 Cycle by Cycle 逐周期 16 cycle skipping 周期跳步 17 Dead Time 死区时间18 DIE Temperature核心温度 19 Disable 非使能，无效，禁用，关断 20 dominant pole 主极点 21 Enable 使能，有效，启用 22 ESD Rating ESD额定值23 Evaluation Board 评估板24 Exceeding the specifications below may result in permanent damage to the device, or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not implied.超过下面的规格使用可能引起永久的设备损害或设备故障。
最全电子行业术语英文翻译
最全电子行业术语英文翻译本文档收集了电子行业中最常见的术语及其英文翻译，以帮助读者更好地理解和使用这些术语。
1. 常见术语及英文翻译- 电子设备 (Electronic device)- 半导体 (Semiconductor)- 集成电路 (Integrated circuit)- 电路板 (Circuit board)- 芯片 (Microchip)- 电 (Capacitor)- 电阻器 (Resistor)- 电感器 (Inductor)- 发光二极管 (Light-emitting diode)- 二极管 (Diode)- 可编程逻辑门阵列 (Programmable logic gate array)- 可编程逻辑控制器 (Programmable logic controller)- 集成封装 (Integrated packaging)- 数字信号处理 (Digital signal processing) - 触摸屏 (Touchscreen)- 无线充电 (Wireless charging)- 人工智能 (Artificial intelligence)- 物联网 (Internet of Things)- 虚拟现实 (Virtual reality)- 增强现实 (Augmented reality)- 机器研究 (Machine learning)2. 其他相关术语- 电池 (Battery)- 蓝牙 (Bluetooth)- Wi-Fi (Wi-Fi)- 供应链管理 (Supply chain management) - 电子支付 (Electronic payment)- 信息安全 (Information security)- 数据隐私 (Data privacy)- 用户界面 (User interface)- 数据存储 (Data storage)- 硬件 (Hardware)- 软件 (Software)- 网络安全 (Network security)- 数据备份 (Data backup)- 电子签名 (Electronic signature)- 电子邮箱 (Email)- 数据恢复 (Data recovery)- 电子证书 (Digital certificate)- 电子表格 (Spreadsheet)- 数据分析 (Data analysis)- 电子文档 (Electronic document)- 云存储 (Cloud storage)请注意，本文档收集的是最常见的电子行业术语及其英文翻译，如果有其他术语需要翻译或有任何疑问，请随时与我联系。
电子产品常用英文词汇
电子产品常用英文词汇一、常见电子电气类英文单词1.功率power2.电压voltage3.电流current4.频率frequency5.效率efficiency6.波形waveform7.交流alternating-current8.直流direct-current9.适配器 adaptor10. 转换器 converter11. 逆变器 inverter12. 充电器 charger13. 控制器 controller14. 启动器 jump starter15. 器件device16. 元件component17. 电容器capacitor18. 电阻resistor19. 电感inductor20. 二极管diode21. 稳压二极管 zener22. 三极管audion23. 场效应管 MOSFEET(Metel-Oxide-Semiconductor Field Effect Transistor)24. 变压器 transformer25. 光藕 optical coupler26. 保险丝 fuse27. 半导体semiconductor28. 瓷片电容 ceramic capacitor29. 电解电容 electrolytic C30. 电感 inductance31. 电容 capacitance32. 电阻 resistance33. 感性的 inductive34. 容性的 capacitive35. 阻性的 resistive36. 阻抗impedance37. 纯正弦波 pure sine wave38. 修正正弦波 modified sine wave39. 方波 square wave40. 恒流源 constant current source41. 恒压源 constant voltage source42. 纹波电流 ripple current43. 涌入电流 inrush current44. 空载电流 no-load current45. 电网 power system46. 死区时间dead time47. 浮充电压 float charge voltage48. 正向电压forward voltage drop49. 续流二极管 freewheel diode50. 肖特基二极管 schottky51. 整流桥 bridge rectifier52. 超快速整流器 ultra fast rectifier53. 检测电阻 sense resistor54. 振荡电阻 timing resistor55. 散热片thermal slug/heat sink/ radiator56. 断路器breaker57. 过流保护器 circuit breaker58. 自由运行 free running59. 满负载 full load60. 过载 overload61. 轻载 light load62. 加载 upload63. 静态 static （state）64. 动态 dynamic （state）65. 稳态的 steady66. 静电 static electricity67. 电源调整率line regulation68. 负载调整率load regulation69. 满载效率 full load efficiency70. 最佳效率 optimum efficiency71. 输出效率 output efficiency72. 峰值效率 peak efficiency73. 标称效率 declared efficiency74. 视在功率 apparent power75. 有功功率 active power76. 无功功率 reactive power77. 功率因数 power-factor78. 耗散功率 power dissipation79. 空载损耗 no-load loss80. 关断状态 off state81. 电源工作电压 operating supply voltage82. 电压参考 voltage reference83. 参考值 reference value84. 反馈feedback85. 产品型号part number86. 掉电power down87. 上电power up88. 电源正常 power good89. 欠压锁定 under voltage lock out (UVLO)90. 上拉 pull up91. 下拉 pull down92. 上升沿 rising edge93. 下降沿 falling edge94. 上限 upper limit95. 下限 lower limit96. 极性 polarity97. 藕合 coupling98. 故障 malfunction99. 原理图 schematic diagram100. 封装footprint101. 设计流程 design cycle102. 设计余量 design margin二、常用电源类英文缩写SPS： switching power supplyPWM: pulse width modulationZCS： zero current switchingZVT: Zero Voltage TransitionPFC: Power Factor CorrectionRMS: Root mean square （均方根）THD: Total Harmonic Distortion (总谐波失真)OVP: Over Voltage ProtectionOCP: Over Current ProtectionOTP: Over Temperature ProtectionMCU: Micro Controller unitTVS: Transient voltage suppressorPCB: Printed circuit boardSMT: surface mounting technologyECR: Engineering Change RequestECN: Engineering Change noticeFMEA: Failure Mode Efficiency AnalysisIC: integrated circuitIE: Industrial EngineeringIT: information technologyAQL: Acceptable Quality LevelQA: Quality AssuranceQC: Qualty ControlIQC: Incoming Quality controlIPQC: In- process Quality control三、变压器类常用材料1. 磁芯：magnetic core2. 骨架：bobbin3. 导线：wire4. 绝缘胶带：insulation tape5. 挡带: margin tape6. 铜箔： copper foil7. 磁环： annular core8. 铁氟龙套管：teflon tube9. 绝缘套管：empire tuble10. 凡立水：varnish11. 气隙：gap12. 绕组：winding13. 初级绕组：primary coil14. 次级绕组：secondary coil15. 电感量: inductance16. 漏感： Leakage inductance17. 耐压：HI-POT18. 绝缘电阻: insulation resistance19. 匝数：turns四、工艺工程类常用英文词汇1. 技术规范：technical regulation2. 规范：specification3. 检修技术：service technic4. 焊接工艺：bonding technology5. 表面安装：surface mounting6. 元件面：component side7. 焊接面：solder side8. 元件孔：component hole9. 安装孔：mounting hole10. 工艺流程图：engineering flow sheet11. 故障指示：failure indication12. 锡焊： tin-lead bonding13. 装配：assembly14. 接插件：socket connector15. 连接器：connector16. 端子：terminal17. 端子壳：housing18. 插座：socket19. 插座盖：socket cover20. 点烟座：cigarette lighter socket21. 点烟头：cigar plug22. 接线座：wire holder23. 接线端子：wire connecting terminal24. 接线器：wire connector25. 线材规格：wire gauge26. 电烙铁： electric solding iron27. 烙铁头：solder horn28. 焊锡： soldering tin29. 焊盘： Pad30. 无铅： Lead Free31. 波峰焊：wave soldering32. 回流焊：reflow soldering33. 老化：burn-in/aging34. 极性： Polarity35. 正级：Positive pole36. 负极：negative pole37. 硬件:hardware38. 软件：software39. 通风孔：vent40. 支撑架/轴承：bearing41. 工艺：technics42. 夹具：fixture43. 冲压模具：die44. 注塑模具：injection mould45. 材料：material46. 扭矩：torque47. 应力：stress48. 强度:strength49. 机壳：enclosure50. 紧固件：fastener51. 螺栓：bolt52. 螺母：nut53. 螺丝：screw54. 垫片：washer55. 套筒扳手：socket key/ socket spanner56. 剪钳：wire cutter57. 剥线皮钳：wire stripper58. 裁线机：wire shear59. 防护罩：guard60. 环氧树脂:epoxy resin61. 玻璃纤维：glass fiber62. 光面：shiny side63. 粗糙面：matte side64. 处理面：treated sideTHANKS致力为企业和个人提供合同协议，策划案计划书，学习课件等等打造全网一站式需求欢迎您的下载，资料仅供参考。
电子行业专业英语词汇
.'专用词汇表一、生产流程1.插机(刮蓝胶)component- inserting2.装配assembly3.修理repair4.包装packaging5.成品仓finished goods warehouse6.返工rework7.啤胶件8.组件成型component moulding9.IC烧录IC program10.插件insection11.注塑plastic injection12.发料material delivery13.插机14.零件加工component-processing15.炉前外观检查visual inspection beforewave soldering16.电源板波峰焊power board wave soldering17.执锡18.零件后焊hand soldering19.零件焊接&打黄胶20.低电压测试low voltage test21.半成品外观检查Semi-finished goods visualinspection22.过水洗机23.打热熔胶dotting hot glue24.装卡板25.pallet栈板26.IC烧录IC program27.SMT(刮锡膏)28.喷油spray conformal coating29.焗干防水油30.welding 焊接31.breathing 排气32.feed 供料33.Tiana天那水34.to load material上料to unload material卸料to return material/stock to退料.'35.to fix a die装模to take apart a die拆模36.cold forging 冷锻press forging 冲锻37.to impose lines压线to compress, compressing压缩38.焗炉温度39.开槽groove40.shearing剪断41.接线端子terminal42.to stake, staking, reviting铆合43.fuse together熔合44.electrical sparkle电火花45.fit together组装在一起46.fasten锁紧(螺丝)47.rotating speed, revolution转速48.argon welding氩焊49.to take apart a die卸下模具50.to load a die装上模具51.to tight a bolt拧紧螺栓to looser a bolt拧松螺栓pound die复合模53.punched hole冲孔54.buffing 抛光55.chamfering machine 倒角机56.panel board镶块57.to cutedges=side cut=side scrap切边58.to pull, to stretch拉伸59.Line streching, line pulling线拉伸60.engraving, to engrave刻印61.degrease脱脂62.rinse水洗63.pierce die冲孔模64.forming die成型模65.progressive die连续模66.gang dies复合模67.shearing die剪边模68.riveting die铆合模69.pierce冲孔70.forming成型(抽凸,冲凸).'71.draw hole抽孔72.吹热缩管73.胶芯plastic core二、夹具设备、工具74.烙铁iron75.排氣扇A exhaust fan76.稀釋劑a tinner77.水洗锡线78.pallet栈板79.gunk 料斗80.caliper gauge 卡规81.Screw driver起子82.barcode scanner条码扫描器83.热风枪hot air reflowing gun84.taker取料机85.roller 滚筒runner 流道86.plastic basket胶筐87.isolating plate baffle plate; barricade隔板88.steel plate钢板89.roll material卷料90.conveyer belt输送带91.transmission rack输送架92.钢网stencil93.油墨printing ink94.插机并过炉95.高压测试hi-pot test96.铣刀milling cutter97.发热管heater98.烙铁咀iron tip99.静电手套ESD gloves 100.风枪air gun101.punch冲头102.g roove punch压线冲子103.a ir vent排气道104.w elding line熔合痕105.C ONN Connector 连接器106.C AV Cavity 模穴107.A SS'Y Assembly 装配,组装108.继电器relay109.磨床切割片110.延时器delay timer.'111.热电偶Heat control sensor 、thermocouple 112.电磁阀Solenoid113.温控器Temperature control114.烙铁发热芯heater core for iron115.剪钳wire cutter116.电批开关Electric screw driver switch 117.电批Electric screw driver118.电批齿轮Electric screw driver gear 119.火牛transformer120.碳刷Carbon brush121.吸锡泵suck solder pump122.尖嘴钳micro long nose pliers123.热熔胶枪glue gun124.热风筒heating gun125.f use machine热熔机126.烙铁座iron seat127.静电带wrist strap128.波峰锡炉wave soldering oven129.水循环系统water-recycling system 130.水洗机131.防水油conformal coating132.自动成型机auto-moulding machine 133.电晶体自动成型机134.螺丝泵screw pump135.恒温运风焗炉136.手浸锡炉137.剪脚机138.超声波蒸水机139.表面组件拾放机140.高周波塑料熔接机141.半自动锡浆印刷机142.剪线机143.超声波啤机ultrasonic welding machine 144.自动绕线机145.超声波清洗机ultrasonic cleaning machine 146.振动试验台vibration test platform 147.计算机剥线机electronic wire-peeling machine148.贴片机SMT equipment149.供料器feeder.'150.红外焗炉151.封黑胶预热炉152.回焊炉温度曲线测试仪153.焗炉154.进料器车155.锡浆搅拌机156.无铅波峰焊机157.开线机158.封口机159.胶纸机160.移载装置161.送板机162.周转车163.发电机electric generator 164.注塑机plastic injection machine 165.碎料机smashing machine 166.干燥机drier167.自动吸料机auto-sucking machine 168.锯床169.车床lathe 170.钻床171.punching machine 冲床172.干燥机drier173.冷水机cooler174.数控精密火花机175.移印机printer176.手动吊机177.热油机oil-heating machine178.叉车forklift179.磨床grinder180.铣床miller181.sheet metal parts 冲件182.punching machine 冲床183.过滤器filter184.碎料干燥机185.抽湿机186.热风回焊炉hot air reflow soldering oven 187.注塑机plastic injeciton machine 188.润滑油grease189.汽缸Rmulti cylinder.'190.螺丝screw191.弹簧spring192.蜂鸣器buzzle193.刮刀squeegee194.真空杯vacuum cup195.真空咀vacuum tip196.喷嘴Nozzle197.支架bracket198.六角板手hex.wrench199.过滤器Filter200.密封圈airproof ring 201.套筒/活塞piston202.顶针thimble203.传输皮带belt/conveyor 204.真空棉 pad vacuum 205.消音器muffler206.滑轮Pulley,idler tension,asy pre-tension207.夹片Replacement Fine Foil 208.线夹wire clamp 209.扎线tie wrap210.通风孔blowhole211.自功螺丝self-tapping screw212.保险丝Fuse213.高度规High dividers214.螺线管solenoid215.送/扯线螺线管Spring solenoid assembly 216.焊咀gaiser217.电源线Power cord218.测试针test probe219.变压器transformer220.弹性定位柱spring fixation pole 221.铝皮sheet aluminum222.网络线communicate wire223.电磁阀Solenoid AIRTAC224.精调电阻Precision adjustable resisto 225.脚踏开关foot switch226.开关电源switching power227.散热片Thermal Conductive Pad 228.旋转开关Rotary switch.'229.接线柱Pole Wiring230.音频插头Audio plug231.按键开关keyswitch232.保险丝座Fuse jack233.定位柱fixation pole234.ICT压棒ICT-PRESSING STICK 235.除泡剂Defoamer236.继电器Relay237.电线束electrical wiring harness 238.锡箔纸Solder foil papper239.针筒needle canister240.光电开关Photoelectricity switch 241.电批Electric screw driver242.烙铁soldering iron243.黄油（润滑油）butter (lubricant) 244.气管wind pipe245.刀片blade246.bolt螺栓247.trailer=long vehicle拖板车248.stopper阻挡器249.flow board流水板250.vaccum cleaner吸尘器251.q uenching淬火252.tempering回火253.annealing退火254.volatile挥发性255.风批Pneumatic driver256.电批Electric screw driver三、质量管理QC : quality control 质量管理257.IQC : incoming quality control 进料质量管理258..OQC : output quality control 出货质量管理259.PQC : process quality control 制程质量管理也称260.IPQC: in process quality control. 261.A QL : acceptable quality level 允收标准262.CQA: customer quality assurance 客户质量保证263.PPM Parts Per Million 百万分之一.'264.MA : major defect 主要缺点MI : minor defect 次要缺点265.CR :critical defect 关键缺点266.SMT : surface mounting technology 表面粘贴技术267.SMD : surface mounting device 贴片机268.SMC : surface mounting component 表面粘贴组件269.ECN : engineering change notice 工程变更通知270.DCN : design change notice 设计变更通知271.B OM : bill of material 物料清单-STD-105E : 美国陆军标准,也称单次抽样计划.273.NG :Not Good 不行,不合格274.ESD Electry-static Discharge 静电排放275.5S 希腊语整理,整顿,清扫,清洁,教养276.Polarity : 电性/极性Icicles : 锡尖277.Non-wetting : 空焊278.burr 毛刺，批锋279.locking knot 死结280.torsion 扭曲281.w arpage 翘曲282.waviness 波痕283.flying 飞件284.blister 起泡285.Short circuit : 短路286.冷焊cold soldering287.non-welding288.假焊289.包焊290.焊点291.l ifted solder 浮焊292.pseudo soldering 虚焊293.open soldering脱焊294.Splay mark 水纹295.icicle/solder projection拉尖.'296.Flow mark 流纹297.White patches on surface 表面白斑298.Sink marks 缩影299.Mold release 脱模300.焊盘soldering tray301.M issing component : 缺件302.Wrong component : 错件303.Excess component : 多件304.Insufficient solder : 锡少305.Excessive solder : 锡多306.Solder residue : 锡渣307.Solder ball : 锡球308.Tombstone : 墓碑309.breaking.(be)broken,(be)cracked 断裂310.S ideward : 侧立311.cosmetic defect外观不良312.mixed color杂色313.die repair模修314.rust生锈315.grease/oil stains油污316.delamination起鳞317.gouge沟槽;凿槽318.inclusion杂质319.poor staking铆合不良320.oxidation 氧化321.abrasion磨损322.reverse angle = chamfer倒角323.failure, trouble故障324.dents压痕325.defective upsiding down抽芽不良326.defective to staking铆合不良327.embedded lump镶块328.feeding is not in place送料不到位329.stamping-missing漏冲330.excessive gap间隙过大331.b urr(金属)flash(塑件)毛边dewed=moldy=mouldy发霉333.slipped screw head & slippery screw head螺丝滑头334.slipped screwhead/shippery screw thread滑手.'335.speckle斑点336.dimension/size is a little bigger尺寸偏大(小)337.not up to standard不合规格out of specification338.shrinking/shrinkage缩水339.mixed color杂色340.discoloration异色341.a geing 老化342.hardening 硬化343.overheating 过热344.rust prevention 防蚀345.tempering 回火346.water spots水渍347.exposed metal/bare metal金属裸露ck of painting烤漆不到位ponent damage : 零件破损350.Gold finger : 金手指351.S OP : standard operation process 标准操作流程352.SIP : standard inspection process 标准检验流程353.Simple random sampling : 简单随机抽样354.SPC : Statistical process control 355.SQE : Supplier quality engineering 356.Sampling sample :抽样计划357.fixture : 治具358.Gauge 量规359.QTS: Quality tracking system 质量追查系统360.Spare parts :备用品361.I nventory report for : 库存表362.Manpower/Tact estimation 工时预算363.Calibration : 校验364.Corrugated pad : 波纹垫365.Conductive bag : 保护袋366.Fixture : 制具367.Probe : 探针368.Lint-free gloves : 静电手套369.Wrist wrap : 静电手环370.plug hole孔塞371.W rong direction 极性反ponent damage or broken 零件破损373.Unmeleted solder熔锡不良374.flux residue松香残渣375.wrong label or upside down label贴反376.mixed parts机种混装377.poor solder mask绿漆不良378.氧化Oxidization379.刮花Scratch380.脏污Contamination381.变形Deformation382.stand off height浮高383.IC reverse IC反向384.supervisor课长385.Forman组长386.R.T.Y: Rolled throughout yield直通率387.PPM: Parts per million 不良率388.DPU: Defects per unit 单位不良率389.Resistor: 电阻390.Capacitor:电容391.R esistor array : 排阻392.Capacitor array: 排容393.DIODE: 二极管394.triode: 三极管395.Crystal:震荡器396.Fuse:保险丝397.Bead: 电感inductor398.Connector:连结器399.Metal Shearing:裁剪400.ERP: Enterprise Resource Planning 企业资源规划401.P rocessed material: 流程性材料402.Corrective action:纠正措施403.Preventive action:预防措施404.PDCA:Plan/Do/Check/Action计划/实施/检查/处理405.Oscillator:振荡器406.Adapter: 适配器407.Spindle:轴心408.WIP: Work in process半成品Waive:特别采用409.FMEA:Protentical Failure Mode and Effects Analysis失效模式与效应分析410.M SA: Measurement Systems Analysis 量测系统分析411.Benchmarking:竞争标竿412.Roka Yoke 防错法413.Mistake Proofing 防呆法414.Fool-Proof System防呆系统415.Specified Requirement:规定要求416.AOQ: Average Outgoing Quality 平均检出质量AOQL: Average OutgoingQuality Limit 平均检出质量界限417.Benchmarking 基准点418.Calibration 校准419.Continuous improvement 持续改进420.Deviation / Substitution 偏差/ 置换421.ESD: Electrostatic discharge 静电释放422.FMEA: Failure Mode Effect Analysis 失误模式效应分析423.First Article approval 产品的首次论证424.First pass yield 一次性通过的成品率425.First sample inspection 第一次样品检验426.FMECA: Failure mode effect and critically analysis 失误模式,效应及后果分析427.Life Testing 寿命试验Lot traceability 批量可追溯性428.NONCONFORMANCE 不符合429.OUT-OF-CONTROL PROCESS 失控工序430.Pilot Application 试产(试用) 431.P PM: Parts per million 百万分之一432.Process capability index 工序能力指数433.Total quality management 全面质量管理434.Site Audit 现场审核435.Failure rate percentage 失误百分率436.Customer complaints 客户投诉437.Root cause analysis of failures 失误根原分析yout Inspection:全尺寸检验439.Bulk material:散装材料440.Feasibility Reviews:可行性审查441.P re-launch:量产前442.Stock rotation :存货周转443.Inventory levels:最低库存量444.Interim action:临时措施445.Permanent action:永久措施446.vibration test振动试验447.Conveyer流水线物料板448.fasten锁紧(螺丝)449.fuse machine热熔机450.SOP制造作业程序451.w ork cell工作间452.trolley台车453.carton纸箱454.电阻Resistor455.电容Capacitor456.晶振Crystal resonator 457.开关Switch458.插座Jack459.插头Plug460.工艺Workmanship 461.喷油Conformal coating 462.插件Insertion463.回焊炉Reflowing oven 464.飞达feeder465.吸嘴466.钢网Stencil467.抛料468.线股Strand469.松香Flux470.尾数WP471.锡炉DIP472.暂置Hold473.全检Sorting474.条形码Bar code475.日期编码Date code476.标准作业指导书SOP Standard operation plan477.过电压保护OVP Over voltage protect 478.汶波/噪声Noise479.连接器Connector480.线材Cable481.C TQ=critical to quality。
电子行业电子英文翻译
电子行业电子英文翻译介绍随着国际间贸易的不断发展和深入，电子行业也变得越来越国际化。
在与国外公司合作或进行技术交流时，电子行业常常需要进行电子英文翻译，以便更好地沟通交流。
本文将介绍电子行业中常见的英文术语，以及如何进行准确和专业的电子英文翻译。
电子行业常用英文术语在进行电子英文翻译时，了解电子行业常用的英文术语是非常重要的。
以下是一些常见的电子行业英文术语：1.Integrated Circuit (IC)：集成电路2.Printed Circuit Board (PCB)：印刷电路板3.Resistor：电阻器4.Capacitor：电容器5.Transistor：晶体管6.Diode：二极管7.Microcontroller：微控制器8.Oscillator：振荡器9.Connector：连接器10.S witch：开关11.P ower Supply：电源12.A mplifier：放大器13.S ensor：传感器14.L ED (Light Emitting Diode)：发光二极管15.L CD (Liquid Crystal Display)：液晶显示屏以上仅是一些常见的电子行业英文术语，电子行业还有许多其他专业术语，根据需要进行适当的补充。
电子英文翻译的技巧在进行电子英文翻译时，以下是一些技巧和建议，以保证翻译的准确性和专业性：1. 理解上下文在进行电子英文翻译时，首先要理解原文所处的上下文。
根据上下文的不同，同一个术语可能有不同的翻译，因此需要根据具体情况进行判断和选择。
2. 使用专业术语电子行业有许多专业术语，尽可能使用原汁原味的英文术语，以保持翻译的专业性。
如果有必要，可以附上相应的中文解释，以便读者更好地理解。
3. 确保准确性电子行业术语的翻译必须保证准确无误。
在进行翻译时，可以参考相关的标准和行业规范，确保翻译的准确性。
4. 使用在线资源在进行电子英文翻译时，可以借助各种在线资源，如术语在线词典、行业技术论坛等。
电子产品常用英文词汇
Electronics Common English Vocabulary1. Battery – The power source for many portable electronic devices. Make sure it's charged before you head out!2. Charger – An accessory that replenishes the battery of your electronic devices.3. Screen – The display area of a device where you view images, videos, and text.5. Mouse – A pointing device used to navigate and interact with graphical user interfaces.6. Speaker – Produces sound from your device, allowing you to listen to music, videos, and more.9. Processor – The brain of your electronic device, responsible for executing instructions and performing calculations.10. RAM (Random Access Memory) – Temporary storage that allows your device to run multiple programs simultaneously.11. Storage – Refers to the amount of data your device can hold, often measured in gigates (GB) or terates (TB).13. Bluetooth – A shortrange wireless technology used for connecting devices, such as headphones, speakers, and keyboards.15. App – Short for application, a software program designed to perform specific tasks on a device.By familiarizing yourself with these terms, you'll be better prepared to discuss and understand the world of electronics. Happy gadget exploring!17. Firmware – A type of software that provides lowlevel control for the device's specific hardware functions.22. SSD (Solid State Drive) – A storage device that uses flash memory to store data, offering faster access times than traditional hard disk drives (HDDs).23. Resolution – The number of pixels in a display, usually described in terms of width and height (e.g.,1920x1080).25. DPI (Dots Per Inch) – A measure of printer resolution, indicating the number of ink dots within an inch of the printed material.26. GHz (Gigahertz) – A unit of frequency equal to one billion hertz, often used to describe the speed of a processor.30. Headphones – Audio devices worn on the ears, usedfor listening to music, podcasts, or other audio content privately.31. Smart Home – A residence equipped with networkconnected devices that can be remotely monitored and controlled, often as part of a home automation system.32. IoT (Internet of Things) – Refers to the network of physical devices, vehicles, appliances, and other items embedded with sensors, software, and connectivity which enables them to collect and exchange data.33. VR (Virtual Reality) – A technology that uses headsets to generate realistic images, sounds, and other sensations that replicate a real or imagined environment.34. AR (Augmented Reality) – A technology that overlays digital information onto the physical world, as seen througha device's camera.35. Cloud Storage – A service that allows users to store data on remote servers, accessible over the internet.37. Software Update – A release of new or revisedsoftware that corrects bugs, improves performance, or addsnew features to an existing program.39. Megapixel – A unit used to measure the number of pixels in an image, often used to describe the quality of a camera sensor.40. DPI (Dots Per Inch) – In the context of screens, it refers to the number of pixels within one inch of the display, affecting the sharpness of the image.41. Aspect Ratio – The proportional relationship between the width and height of a display or image, typically expressed as two numbers separated a colon (e.g., 16:9).42. URL (Uniform Resource Locator) – The address used to find a particular resource on the internet, such as a website or file.43. VPN (Virtual Private Network) – A service that creates a secure, encrypted connection over a less secure network, such as the internet.49. WiFi Direct – A technology that enables devices to connect with each other without the need for a wireless access point or internet connection.51. SIM Card (Subscriber Identity Module) – A small card that identifies a subscriber on a mobile network and stores personal data, allowing the device to connect to the network.53. ROM (ReadOnly Memory) – A type of memory that can only be read, not written to, which stores data that must be permanently saved, such as the firmware of a device.。
电子产品英文术语大全
品质管理电子产品的英文术语大全从事品质工作以来积累的常用英语，希望对有需要的朋友有所帮助！品质专业英语大全零件材料类的专有名词CPU: central processing unit(中央处理器)IC: Integrated circuit(集成电路)Memory IC: Memory Integrated circuit（记忆集成电路）RAM: Random Access Memory（随机存取存储器）DRAM: Dynamic Random Access Memory（动态随机存取存储器）SRAM: Staic Random Access Memory（静态随机存储器）ROM: Read-only Memory（只读存储器）EPROM:Electrical Programmable Read-only Memory（电可抹只读存诸器）EEPROM: Electrical Erasbale Programmable Read-only Memory（电可抹可编程只读存储器）CMOS: Complementary Metal-Oxide-Semiconductor（互补金属氧化物半导体）BIOS: Basic Input Output System（基本输入输出系统）Transistor：电晶体LED:发光二极体Resistor：电阻Variator：可变电阻Capacitor:电容Capacitor array：排容Diode：二极体Transistor：三极体Transformer：变压器（ADP）Oscillator：频率振荡器（0sc）Crystal：石英振荡器XTAL/OSC:振荡产生器（X）Relay：延时器Sensor：感应器Bead core：磁珠Filter:滤波器Flat Cable：排线Inductor：电感Buzzer：蜂鸣器Socket：插座Slot：插槽Fuse：熔断器Current：电流表Solder iron：电烙铁Magnifying glass：放大镜Driver：螺丝起子Oven：烤箱TFT:液晶显示器Oscilloscope：示波器Connector：连接器PCB:printed circuit board（印刷电路板）PCBA: printed circuit board assembly（电路板成品）PP:并行接口HDD:硬盘FDD:软盘PSU:power supply unit（电源供应器）SPEC:规格Attach:附件Case: 机箱，盖子Cover：上盖Base：下盖Bazel：面板（panel）Bracket：支架，铁片Lable：贴纸Guide：手册Manual：手册，指南Card：网卡Switch：交换机Hub：集线器Router：路由器Sample：样品Gap：间隙Sponge：海绵Pallet：栈板Foam：保利龙Fiber：光纤Disk：磁盘片PROG:程序Barcode：条码System：系统System Barcode：系统条码M/B:mother board：主板CD-ROM:光驱FAN:风扇Cable：线材Audio：音效K/B:Keyboard（键盘）Mouse：鼠标Card reader：读卡器Screw：螺丝Thermal pad：散热垫Heat sink：散热片Rubber：橡胶垫Rubber foot：脚垫Bag：袋子Washer：垫圈Sleeve：袖套Config：机构Label hi-pot：高压标签Firmware label：烧录标签Metal cover：金属盖子Plastic cover：塑胶盖子Tape for packing：包装带Bar code：条码Tray：托盘Collecto：集线夹Holder：固定器,L铁Connecter：连接器IDE:集成电路设备，智能磁盘设备SCSI:小型计算机系统接口Gasket：导电泡棉AGP:加速图形接口PCI:周边组件扩展接口LAN:局域网USB:通用串形总线架构Slim：小型化COM:串型通讯端口LPT:打印口，并行口Power cord：电源线I/O:输入，输出Speaker：扬声器EPE:泡棉Carton：纸箱Button：按键，按钮Foot stand：脚架部门名称的专有名词QS:Quality system品质系统CS:Coutomer Sevice 客户服务QC:Quality control品质管理IQC:Incoming quality control 进料检验LQC:Line Quality Control 生产线品质控制IPQC:In process quality control 制程检验FQC:Final quality control 最终检验OQC:Outgoing quality control 出货检验QA:Quality assurance 品质保证SQA:Source(supplier) Quality Assurance 供应商品质保证(VQA) CQA：Customer Quality Assurance客户质量保证PQA rocess Quality Assurance 制程品质保证QE:Quality engineer 品质工程CE:component engineering零件工程EE:equipment engineering设备工程ME:manufacturing engineering制造工程TE:testing engineering测试工程PPE roduct Engineer 产品工程IE:Industrial engineer 工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC:producing control生管MC:mater control物管GAD: General Affairs Dept总务部A/D: Accountant /Finance Dept会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchaing Dept)SMT:Surface mount technology 表面粘着技术MFG:Manufacturing 制造MIS:Management information system 资迅管理系统DCC:document control center 文件管制中心厂内作业中的专有名词QT:Quality target品质目标QP:Quality policy目标方针QI:Quality improvement品质改善CRITICAL DEFECT:严重缺点（CR）MAJOR DEFECT:主要缺点（MA）MINOR DEFECT:次要缺点（MI）MAX:Maximum最大值MIN:Minimum最小值DIA iameter直径DIM imension尺寸LCL:Lower control limit管制下限UCL:Upper control limit管制上限EMI:电磁干扰ESD:静电防护EPA:静电保护区域ECN:工程变更ECO:Engineering change order工程改动要求（客户）ECR:工程变更需求单CPI:Continuous Process Improvement 连续工序改善Compatibility：兼容性Marking：标记DWG rawing图面Standardization：标准化Consensus：一致Code：代码ZD:Zero defect零缺点Tolerance：公差Subject matter：主要事项Auditor：审核员BOM:Bill of material物料清单Rework：重工ID：identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR：First Piece Inspection Report首件检查报告FAA:首件确认SPC：统计制程管制CP: capability index（准确度）CPK: capability index of process(制程能力) PMP:制程管理计划（生产管制计划）MPI:制程分析DAS efects Analysis System 缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N:料号L/N：Lot Number批号Version：版本Quantity：数量Valid date：有效日期MIL-STD：Military-Standard军用标准ICT: In Circuit Test (线路测试)ATE：Automatic Test Equipment自动测试设备MO: Manafacture Order生产单T/U: Touch Up (锡面修补)I/N:手插件P/T:初测F/T: Function Test (功能测试-终测)AS 组立P/K:包装TQM:Total quality control全面品质管理MDA:manufacturing defect analysis制程不良分析(ICT)RUN-IN:老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect高频测试DPPM: Defect Part Per Million(不良率的一种表达方式：百万分之一) 1000PPM即为0.1%Corrective Action: (CAR改善对策)ACC：允收REJ:拒收S/S：Sample size抽样检验样本大小SI-SIV：Special I-Special IV特殊抽样水平等级CON：Concession / Waive特采ISO:国际标准化组织ISA：Industry Standard Architecture工业标准体制结构OBA:开箱稽核FIFO:先进先出PDCA:管理循环Plan do check action计划，执行，检查，总结(计划，实施，检查，处置) WIP:在制品（半成品）S/O: Sales Order (业务订单)P/O: Purchase Order (采购订单)P/R: Purchase Request (请购单)AQL:acceptable quality level允收品质水准LQL;Limiting quality level最低品质水准QVL:qualified vendor list合格供应商名册AVL ：认可的供货商清单(Approved Vendor List)QCD: Quality cost delivery（品质，交期，成本）MPM:Manufacturing project management制造专案管理KPI:Key performance indicate重要绩效指标MVT:Manufacturing Verification Test制造验证试产Q/R/S：Quality/Reliability/Service质量/可靠度/服务STL:ship to line（料到上线）NTF:No trouble found误判CIP:capacity improvement plan（产能改善计划）MRB:material review board（物料审核小组）MRB:Material reject bill退货单JIT:just in time（即时管理）5S:seiri seiton seiso seiketsu shitsuke（整理，整顿，清扫，清洁，修养）SOP:standard operation process（标准作业程序）SIP:Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction（作业指导书）SMD:surface mounting device（表面粘着原件）FAR:failure aualysis report故障分析报告CAR:Corrective action report改善报告BPR：企业流程再造 (Business Process Reengineering)ISAR ：首批样品认可(Initial Sample Approval Request)-JIT：实时管理 (Just In Time)QCC ：品管圈 (Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面品质环境管理)PD: Production Department (制造)LOG: Logistics (后勤支持)Shipping: (进出口)AOQ：Average Output Quality平均出货质量AOQL：Average Output Quality Level平均出货质量水平FMEA：failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA：Customer Simulate Analysis客户模拟分析SQMS：Supplier Quality Management System供应商品质管理系统QIT: Quality Improvement Team 品质改善小组QIP：Quality Improvement Plan品质改善计划CIP：Continual Improvement Plan持续改善计划M.Q.F.S: Material Quality Feedback Sheet (来料品质回馈单)SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D单)小组成立问题说明实施并验证临时措施确定并验证根本原因选择并验证永久纠正措施实施永久纠正措施预防再发生小组祝贺PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知)QAPS: Quality Assurance Process Sheet (品质工程表)DRP ：运销资源计划 (Distribution Resource Planning)DSS：决策支持系统 (Decision Support System)EC ：电子商务 (Electronic Commerce)EDI ：电子资料交换 (Electronic Data Interchange)EIS ：主管决策系统 (Excutive Information System)ＥＲＰ：企业资源规划 (Enterprise Resource Planning)FMS ：弹性制造系统 (Flexible Manufacture System)KM ：知识管理 (Knowledge Management)4L ：逐批订购法 (Lot-for-Lot)LTC ：最小总成本法 (Least Total Cost)LUC ：最小单位成本 (Least Unit Cost)MES ：制造执行系统 (Manufacturing Execution System) MPS ：主生产排程 (Master Production Schedule)MRP ：物料需求规划 (Material Requirement Planning) MRPⅡ：制造资源计划 (Manufacturing Resource Planning) OEM ：委托代工 (Original Equipment Manufacture)ODM ：委托设计与制造 (Original Design & Manufacture) OLAP：线上分析处理 (On-Line Analytical Processing) OLTP：线上交易处理 (On-Line Transaction Processing) OPT ：最佳生产技术 (Optimized Production Technology) PDCA：PDCA管理循环 (Plan-Do-Check-Action)PDM：产品数据管理系统 (Product Data Management)) RCCP：粗略产能规划 (Rough Cut Capacity Planning) SCM ：供应链管理 (Supply Chain Management)SFC ：现场控制 (Shop Floor Control)TOC：限制理论 (Theory of Constraints)TQC ：全面品质管制 (Total Quality Control)FYI/R:for your information/reference仅供参考ASAP:尽快S/T:Standard time标准时间TPM:total production maintenance：全面生产保养ESD Wrist strap：静电环IT:information technology信息技术，资讯科学CEO：Chief Executive Officer执行总裁COO：Chief Operaring Officer首席业务总裁SWOT：Strength,Weakness,Opportunity,Threat优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通Cooperation：统御融合Vibration Testing：振动测试IDP：Individual Development Plan个人发展计划MRP：Material Requirement Planning物料需求计划MAT'S：Material材料LRR：Lot Rejeet Rate批退率ATIN：Attention知会3C：Computer ,Communication , Consumer electronic消费性电子5W1H：When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement 人,机器,材料,方法,测量4MIE: Man,Material,Machine,Method,Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money , Information 人力，机器，材料，方法, 市场，管理，资金，资讯1 Accuracy 准确度2 Action 行动3 Activity 活动4 Analysis Covariance 协方差分析5 Analysis of Variance 方差分析6 Approved 承认7 Attribute 计数值8 Average 平均数9 Balance sheet 资产负债对照表10 Binomial 二项分配11 Brainstorming Techniques 脑力风暴法12 Cause and Effect Matrix 因果图(鱼骨图)13 CL:Center Line 中心线14 Check Sheets 检查表15 Complaint 投诉16 Conformity 合格（符合）17 Control 控制18 Control chart 控制(管制)图19 Correction 纠正20 Correlation Methods 相关分析法21 CPI: continuouse Process Improvement 连续工序改善22 Cross Tabulation Tables 交叉表23 CS: Customer Sevice 客（户）服（务）中心24 DSA: Defects Analysis System 缺陷分析系统25 Data 数据 Description:品名26 DCC: Document Control Center 文控中心27 Decision 决策、判定28 Defects per unit 单位缺点数29 Description 描述30 Device 装置31 Do 执行32 DOE: Design of Experiments 实验设计33 Element 元素34 Engineering recbnology 工程技35 Environmental 环境36 Equipment 设备37 Estimated accumulative frequency 计算估计累计数38 E Equipment Variation 设备变异39 External Failure 外部失效,外部缺陷40 FA: Failure Analysis 失效分析41 Fact control 事实管理42 Fatigue 疲劳43 FMEA: Failure Mode and Effect Analysis失效模式与效果分析44 FP First-Pass Yield （第一次通过）合格率45 FQA: Final Quality Assurance 最终品质保证46 FQC: Final Quality control 最终品质控制47 Gauge system 测量系统48 Grade 等级49 Histogram 直方图50 Improvement 改善51 Initial review 先期审查52 Inspection 检验53 Internal Failure 内部失效、内部缺陷54 IPQC: In Process Quality Control 制程品质控制55 IQC: Incomming Quality Control 来料品质控制56 IS International Organization for Standardization 国际标准化组织57 LCL: Lower Control limit 管制下限58 LQC: Line Quality Control 生产线品质控制59 LSL: Lower Size Limit 规格下限60 Machine 机械61 Manage 管理62 Materials 物料63 Measurement 测量64 Median 中位数65 MSA: Measurement System Analysis 测量系统分析66 Occurrence 发生率67 Operation Instruction 作业指导书68 Organization 组织69 Parto 柏拉图70 PPM arts per Million （百万分之）不良率71 Plan 计划72 Policy 方针73 Population 群体74 PQA: Process Quality Assurance 制程品质保证75 Practice 实务(践)76 Prevention 预防77 Probability 机率78 Probability density function 机率密度函数79 Procedure 流程80 Process 过程81 Process capability analysis 制程能力分析（图）82 Process control and Process capability制程管制与制程能力83 Product 产品84 Production 生产85 Projects 项目86 QA: Quality Assurance 品质保证87 QC: Quality Control 品质控制88 QE: Quality Engineering 品质工程89 QFD: Quality Function Desgin 品质机能展开(法)90 Quality 质量91 Quality manual 品质手册92 Quality policy 品质政策(质量方针)93 Random experiment 随机试验94 Random numbers 随机数95 R:Range 全距（极差）96 Reject 拒收97 Repair 返修98 Repeatusility 再现性99 Reproducibility 再生性100 Requirement 要求101 Responsibilities 职责102 Review 评审103 Reword 返工104 Rolled yield 直通率105 RPN: Risk Priority Number 风险系数106 Sample 抽样,样本107 Sample space 样本空间108 Sampling with replacement 放回抽样109 Sampling without replacement 不放回抽样110 Scatter diagram 散布图分析111 Scrap 报废112 Simple random sampling 简单随机取样113 Size 规格114 SL: Size Line 规格中心线115 Stratified random sampling 分层随机抽样116 SOP: Standard Operation Procedure 标准作业书117 SPC: Statistical Process Control 统计制程管制118 Specification 规范119 SQA: Source(Supplier) Quality Assurance 供货商品质保证120 Stage sampling 分段随机抽样121 Standard Deviation 标准差122 Sum of squares 平方和123 Taguchi-method 田口(试验)方法124 Theory 原理125 TQC: Total Quality Control 全面品质控制126 TQM: Total Quality Management 全面品质管理127 Traceablity 追溯128 Training 培训129 UCL: Upper Control Limit 管制（控制）上限130 USL: Upper Size Limit 规格上限131 Validation 确认132 Variable 计量值133 Verification 验证134 Version 版本135 VOC: Voice of Customer 客户需求136 VOE: Voice of Engineer 工程需求137 Inventory stock report:庫存清单报告138 Sales order report:出货报告质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproductiveness & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善小组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable专业词汇通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位Human Resources Department人力资源部Head count 人头数production department生产部门planning department企划部QC Section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 计算机外壳(组件)personal computer enclosure 计算机机箱产品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上盖base pan 基座bezel 面板riser card 扩充卡flat cable 排线TOP driver cage 上磁架bottom driver cage 下磁架resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑料件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程窗体production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck 瓶颈模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模stage die工程模compound die复合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 换模to fix a die装模to repair a die修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)upper supporting blank上承板upper padding plate blank上垫板top plate上托板（顶板）top block上垫脚stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块die locker锁模器pressure plate =plate pinch压板thickness gauge厚薄规cutting die, blanking die冲裁模die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条panel board镶块to load a die装上模具to unload a die 御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块pilot导正筒trim剪外边pierce剪内边pocket for the punch head挂钩槽slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch =die button圆冲子shape punch =die insert异形子stock located block定位块metal plate钣金miller铣床grinder磨床tolerance公差score =groove压线sliding block滑块lathe车active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板capability能力parameter参数factor系数driller钻床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves =spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold挤压式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue, cont.连动to grip(material)吸料location lump, locating piece, location block定位块reset复位to file burr 锉毛刺embedded lump |in'bed| mp|镶块 |lstamping-missing漏冲to tight a bolt拧紧螺栓to loosen a bolt拧松螺栓punched hole冲孔to cut edge =side cut =side scrap 切边to bending折弯to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake铆合designing, to design设计design modification 设计修改成gauge(or jig)治具pedal踩踏板stopper阻挡器flow board流水板torque扭矩spline =the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的forming成型(抽凸,冲凸)draw hole抽孔bending折弯emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线stamp letter冲字(料号)tick-mark nearside正面压印tick-mark farside反面压印冲压类punch, press冲punching machine 冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management制造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包成型类well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口runner less无浇道sprue less 无射料管方式long nozzle延长喷嘴方式spur浇口;溶waste废料board广告牌sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理组装类Assembly line组装线Layout布置图Conveyer流水线运输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine/heat stake热熔机processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机烤漆类phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉organic solvent有机溶剂demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料volatile挥发性degrease脱脂rinse水洗alkaline etch龄咬desmot剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔scraped products报放品disposed products处理品dismantle the die折模auxiliary function辅助功能heater band 加热片thermocouple热电偶derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response =reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线grit沙砾granule =pellet =grain细粒sand blasting喷沙grit maker抽粒机cushion缓冲fillet镶;嵌边roller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴品质类qualified products, up-to-grade products良品defective products, not up-to-grade products不良品。
电子产品常用英文词汇
电子产品常用英文词汇一、常见电子电气类英文单词1.功率power2.电压voltage3.电流current4.频率frequency5.效率efficiency6.波形waveform7.交流alternating-current8.直流direct-current9.适配器 adaptor10. 转换器 converter11. 逆变器 inverter12. 充电器 charger13. 控制器 controller14. 启动器 jump starter15. 器件device16. 元件component17. 电容器capacitor18. 电阻resistor19. 电感inductor20. 二极管diode21. 稳压二极管 zener22. 三极管audion23. 场效应管 MOSFEET(Metel-Oxide-Semiconductor Field Effect Transistor)24. 变压器 transformer25. 光藕 optical coupler26. 保险丝 fuse27. 半导体semiconductor28. 瓷片电容 ceramic capacitor29. 电解电容 electrolytic C30. 电感 inductance31. 电容 capacitance32. 电阻 resistance33. 感性的 inductive34. 容性的 capacitive35. 阻性的 resistive36. 阻抗impedance37. 纯正弦波 pure sine wave38. 修正正弦波 modified sine wave39. 方波 square wave40. 恒流源 constant current source41. 恒压源 constant voltage source42. 纹波电流 ripple current43. 涌入电流 inrush current44. 空载电流 no-load current45. 电网 power system46. 死区时间dead time47. 浮充电压 float charge voltage48. 正向电压forward voltage drop49. 续流二极管 freewheel diode50. 肖特基二极管 schottky51. 整流桥 bridge rectifier52. 超快速整流器 ultra fast rectifier53. 检测电阻 sense resistor54. 振荡电阻 timing resistor55. 散热片thermal slug/heat sink/ radiator56. 断路器breaker57. 过流保护器 circuit breaker58. 自由运行 free running59. 满负载 full load60. 过载 overload61. 轻载 light load62. 加载 upload63. 静态 static （state）64. 动态 dynamic （state）65. 稳态的 steady66. 静电 static electricity67. 电源调整率line regulation68. 负载调整率load regulation69. 满载效率 full load efficiency70. 最佳效率 optimum efficiency71. 输出效率 output efficiency72. 峰值效率 peak efficiency73. 标称效率 declared efficiency74. 视在功率 apparent power75. 有功功率 active power76. 无功功率 reactive power77. 功率因数 power-factor78. 耗散功率 power dissipation79. 空载损耗 no-load loss80. 关断状态 off state81. 电源工作电压 operating supply voltage82. 电压参考 voltage reference83. 参考值 reference value84. 反馈feedback85. 产品型号part number86. 掉电power down87. 上电power up88. 电源正常 power good89. 欠压锁定 under voltage lock out (UVLO)90. 上拉 pull up91. 下拉 pull down92. 上升沿 rising edge93. 下降沿 falling edge94. 上限 upper limit95. 下限 lower limit96. 极性 polarity97. 藕合 coupling98. 故障 malfunction99. 原理图 schematic diagram100. 封装footprint101. 设计流程 design cycle102. 设计余量 design margin二、常用电源类英文缩写SPS： switching power supplyPWM: pulse width modulationZCS： zero current switchingZVT: Zero Voltage TransitionPFC: Power Factor CorrectionRMS: Root mean square （均方根）THD: Total Harmonic Distortion (总谐波失真)OVP: Over Voltage ProtectionOCP: Over Current ProtectionOTP: Over Temperature ProtectionMCU: Micro Controller unitTVS: Transient voltage suppressorPCB: Printed circuit boardSMT: surface mounting technologyECR: Engineering Change RequestECN: Engineering Change noticeFMEA: Failure Mode Efficiency AnalysisIC: integrated circuitIE: Industrial EngineeringIT: information technologyAQL: Acceptable Quality LevelQA: Quality AssuranceQC: Qualty ControlIQC: Incoming Quality controlIPQC: In- process Quality control三、变压器类常用材料1. 磁芯：magnetic core2. 骨架：bobbin3. 导线：wire4. 绝缘胶带：insulation tape5. 挡带: margin tape6. 铜箔： copper foil7. 磁环： annular core8. 铁氟龙套管：teflon tube9. 绝缘套管：empire tuble10. 凡立水：varnish11. 气隙：gap12. 绕组：winding13. 初级绕组：primary coil14. 次级绕组：secondary coil15. 电感量: inductance16. 漏感： Leakage inductance17. 耐压：HI-POT18. 绝缘电阻: insulation resistance19. 匝数：turns四、工艺工程类常用英文词汇1. 技术规范：technical regulation2. 规范：specification3. 检修技术：service technic4. 焊接工艺：bonding technology5. 表面安装：surface mounting6. 元件面：component side7. 焊接面：solder side8. 元件孔：component hole9. 安装孔：mounting hole10. 工艺流程图：engineering flow sheet11. 故障指示：failure indication12. 锡焊： tin-lead bonding13. 装配：assembly14. 接插件：socket connector15. 连接器：connector16. 端子：terminal17. 端子壳：housing18. 插座：socket19. 插座盖：socket cover20. 点烟座：cigarette lighter socket21. 点烟头：cigar plug22. 接线座：wire holder23. 接线端子：wire connecting terminal24. 接线器：wire connector25. 线材规格：wire gauge26. 电烙铁： electric solding iron27. 烙铁头：solder horn28. 焊锡： soldering tin29. 焊盘： Pad30. 无铅： Lead Free31. 波峰焊：wave soldering32. 回流焊：reflow soldering33. 老化：burn-in/aging34. 极性： Polarity35. 正级：Positive pole36. 负极：negative pole37. 硬件:hardware38. 软件：software39. 通风孔：vent40. 支撑架/轴承：bearing41. 工艺：technics42. 夹具：fixture43. 冲压模具：die44. 注塑模具：injection mould45. 材料：material46. 扭矩：torque47. 应力：stress48. 强度:strength49. 机壳：enclosure50. 紧固件：fastener51. 螺栓：bolt52. 螺母：nut53. 螺丝：screw54. 垫片：washer55. 套筒扳手：socket key/ socket spanner56. 剪钳：wire cutter57. 剥线皮钳：wire stripper58. 裁线机：wire shear59. 防护罩：guard60. 环氧树脂:epoxy resin61. 玻璃纤维：glass fiber62. 光面：shiny side63. 粗糙面：matte side64. 处理面：treated side。
电子行业专业英语词汇
专用词汇表一、生产流程1.插机(刮蓝胶)component- inserting2.装配assembly3.修理repair4.包装packaging5.成品仓finished goods warehouse6.返工rework7.啤胶件8.组件成型component moulding9.IC烧录IC program10.插件insection11.注塑plastic injection12.发料material delivery13.插机14.零件加工component-processing15.炉前外观检查visual inspection beforewave soldering16.电源板波峰焊power board wave soldering17.执锡18.零件后焊hand soldering19.零件焊接&打黄胶20.低电压测试low voltage test21.半成品外观检查Semi-finished goods visualinspection22.过水洗机23.打热熔胶dotting hot glue24.装卡板25.pallet栈板26.IC烧录IC program27.SMT(刮锡膏)28.喷油spray conformal coating29.焗干防水油30.welding 焊接31.breathing 排气32.feed 供料33.Tiana天那水34.to load material上料35.to unload material卸料36.to return material/stock to退料37.to fix a die装模38.to take apart a die拆模39.cold forging 冷锻40.press forging 冲锻41.to impose lines压线42.to compress, compressing压缩43.焗炉温度44.开槽groove45.shearing剪断46.接线端子terminal47.to stake, staking, reviting铆合48.fuse together熔合49.electrical sparkle电火花50.fit together组装在一起51.fasten锁紧(螺丝)52.rotating speed, revolution转速53.argon welding氩焊54.to take apart a die卸下55.to load a die装上56.to tight a bolt拧紧螺栓57.to looser a bolt拧松螺栓pound die复合模59.punched hole冲孔60.buffing 抛光61.chamfering machine 倒角机62.panel board镶块63.to cutedges=side cut=side scrap切边64.to pull, to stretch拉伸65.Line streching, line pulling线拉伸66.engraving, to engrave刻印67.degrease脱脂68.rinse水洗69.pierce die冲孔模70.forming die成型模71.progressive die连续模72.gang dies复合模73.shearing die剪边模74.riveting die铆合模75.pierce冲孔76.forming成型(抽凸,冲凸)77.draw hole抽孔78.吹热缩管79.胶芯plastic core二、夹具设备、工具80.烙铁iron81.排氣扇A exhaust fan82.稀釋劑a tinner83.水洗锡线84.pallet栈板85.gunk 料斗86.caliper gauge 卡规87.Screw driver起子88.barcode scanner条码扫描器89.热风枪hot air reflowing gun90.taker取料机91.roller 滚筒runner 流道92.plastic basket胶筐93.isolating plate baffle plate; barricade隔板94.steel plate钢板95.roll material卷料96.conveyer belt输送带97.transmission rack输送架98.钢网stencil99.油墨printing ink100.插机并过炉101.高压测试hi-pot test102.铣刀milling cutter103.发热管heater104.烙铁咀iron tip105.静电手套ESD gloves106.风枪air gun 107.p unch冲头108.g roove punch压线冲子109.a ir vent排气道110.welding line熔合痕111.CONN Connector 连接器112.CAV Cavity 模穴113.ASS'Y Assembly 装配,组装114.继电器relay115.磨床切割片116.延时器delay timer117.热电偶Heat control sensor 、thermocouple 118.电磁阀Solenoid119.温控器Temperature control120.烙铁发热芯heater core for iron121.剪钳wire cutter122.电批开关Electric screw driver switch 123.电批Electric screw driver124.电批齿轮Electric screw driver gear 125.火牛transformer126.碳刷Carbon brush127.吸锡泵suck solder pump128.尖嘴钳micro long nose pliers129.热熔胶枪glue gun130.热风筒heating gun131.fuse machine热熔机132.烙铁座iron seat133.静电带wrist strap134.波峰锡炉wave soldering oven135.水循环系统water-recycling system 136.水洗机137.防水油conformal coating138.自动成型机auto-moulding machine 139.电晶体自动成型机140.螺丝泵screw pump141.恒温运风焗炉142.手浸锡炉143.剪脚机144.超声波蒸水机145.表面组件拾放机146.高周波塑料熔接机147.半自动锡浆印刷机148.剪线机149.超声波啤机ultrasonic welding machine 150.自动绕线机151.超声波清洗机ultrasonic cleaning machine 152.振动试验台vibration test platform 153.计算机剥线机electronic wire-peeling machine154.贴片机SMT equipment155.供料器feeder156.红外焗炉157.封黑胶预热炉158.回焊炉温度曲线测试仪159.焗炉160.进料器车161.锡浆搅拌机162.无铅波峰焊机163.开线机164.封口机165.胶纸机166.移载装置167.送板机168.周转车169.发电机electric generator170.注塑机plastic injection machine 171.碎料机smashing machine172.干燥机drier173.自动吸料机auto-sucking machine 174.锯床175.车床lathe176.钻床177.punching machine 冲床178.干燥机drier179.冷水机cooler180.数控精密火花机181.移印机printer182.手动吊机183.热油机oil-heating machine184.叉车forklift185.磨床grinder186.铣床miller187.sheet metal parts 冲件188.punching machine 冲床189.过滤器filter190.碎料干燥机191.抽湿机192.热风回焊炉hot air reflow soldering oven 193.注塑机plastic injeciton machine 194.润滑油grease195.汽缸Rmulti cylinder196.螺丝screw197.弹簧spring198.蜂鸣器buzzle199.刮刀squeegee200.真空杯vacuum cup201.真空咀vacuum tip202.喷嘴Nozzle203.支架bracket204.六角板手hex.wrench205.过滤器Filter206.密封圈airproof ring207.套筒/活塞piston208.顶针thimble209.传输皮带belt/conveyor210.真空棉 pad vacuum211.消音器muffler212.滑轮Pulley,idler tension,asy pre-tension 213.夹片Replacement Fine Foil214.线夹wire clamp215.扎线tie wrap216.通风孔blowhole217.自功螺丝self-tapping screw218.保险丝Fuse219.高度规High dividers220.螺线管solenoid221.送/扯线螺线管Spring solenoid assembly 222.焊咀gaiser223.电源线Power cord224.测试针test probe225.变压器transformer226.弹性定位柱spring fixation pole 227.铝皮sheet aluminum228.网络线communicate wire229.电磁阀Solenoid AIRTAC230.精调电阻Precision adjustable resisto 231.脚踏开关foot switch232.开关电源switching power233.散热片Thermal Conductive Pad 234.旋转开关Rotary switch235.接线柱Pole Wiring236.音频插头Audio plug237.按键开关keyswitch 238.保险丝座Fuse jack239.定位柱fixation pole240.ICT压棒ICT-PRESSING STICK 241.除泡剂Defoamer242.继电器Relay243.电线束electrical wiring harness 244.锡箔纸Solder foil papper245.针筒needle canister246.光电开关Photoelectricity switch 247.电批Electric screw driver248.烙铁soldering iron249.黄油（润滑油）butter (lubricant) 250.气管wind pipe251.刀片blade252.bolt螺栓253.trailer=long vehicle拖板车254.stopper阻挡器255.flow board流水板256.vaccum cleaner吸尘器257.quenching淬火258.tempering回火259.annealing退火260.volatile挥发性261.风批Pneumatic driver262.电批Electric screw driver三、质量管理QC : quality control 质量管理263.IQC : incoming quality control 进料质量管理264..OQC : output quality control 出货质量管理265.PQC : process quality control 制程质量管理也称266.IPQC: in process quality control. 267.AQL : acceptable quality level 允收标准268.CQA: customer quality assurance 客户质量保证269.PPM Parts Per Million 百万分之一270.MA : major defect 主要缺点MI : minor defect 次要缺点271.C R :critical defect 关键缺点272.SMT : surface mounting technology 表面粘贴技术273.SMD : surface mounting device 贴片机274.SMC : surface mounting component 表面粘贴组件275.ECN : engineering change notice 工程变更通知276.DCN : design change notice 设计变更通知277.BOM : bill of material 物料清单-STD-105E : 美国陆军标准,也称单次抽样计划.279.NG :Not Good 不行,不合格280.ESD Electry-static Discharge 静电排放281.5S 希腊语整理,整顿,清扫,清洁,教养282.Polarity : 电性/极性Icicles : 锡尖283.Non-wetting : 空焊284.burr 毛刺，批锋285.locking knot 死结286.torsion 扭曲287.warpage 翘曲288.waviness 波痕289.flying 飞件290.blister 起泡291.S hort circuit : 短路292.冷焊cold soldering293.non-welding294.假焊295.包焊296.焊点297.lifted solder 浮焊298.pseudo soldering 虚焊299.open soldering脱焊300.Splay mark 水纹301.i cicle/solder projection拉尖302.Flow mark 流纹303.White patches on surface 表面白斑304.Sink marks 缩影305.Mold release 脱模306.焊盘soldering tray307.Missing component : 缺件308.Wrong component : 错件309.Excess component : 多件310.I nsufficient solder : 锡少311.Excessive solder : 锡多312.S older residue : 锡渣313.S older ball : 锡球314.T ombstone : 墓碑315.b reaking.(be)broken,(be)cracked 断裂316.S ideward : 侧立317.c osmetic defect外观不良318.mixed color杂色319.die repair模修320.rust生锈321.grease/oil stains油污322.delamination起鳞323.gouge沟槽;凿槽324.inclusion杂质325.poor staking铆合不良326.oxidation 氧化327.abrasion磨损328.reverse angle = chamfer倒角329.failure, trouble故障330.dents压痕331.d efective upsiding down抽芽不良332.defective to staking铆合不良333.embedded lump镶块334.feeding is not in place送料不到位335.stamping-missing漏冲336.excessive gap间隙过大337.burr(金属)flash(塑件)毛边dewed=moldy=mouldy发霉339.slipped screw head & slippery screw head螺丝滑头340.slipped screwhead/shippery screw thread滑手341.s peckle斑点342.dimension/size is a little bigger尺寸偏大(小)343.not up to standard不合规格out of specification344.shrinking/shrinkage缩水345.mixed color杂色346.discoloration异色347.ageing 老化348.hardening 硬化349.overheating 过热350.rust prevention 防蚀351.t empering 回火352.water spots水渍353.exposed metal/bare metal金属裸露ck of painting烤漆不到位ponent damage : 零件破损356.Gold finger : 金手指357.SOP : standard operation process 标准操作流程358.SIP : standard inspection process 标准检验流程359.Simple random sampling : 简单随机抽样360.SPC : Statistical process control 361.S QE : Supplier quality engineering 362.Sampling sample :抽样计划363.fixture : 治具364.Gauge 量规365.QTS: Quality tracking system 质量追查系统366.Spare parts :备用品367.Inventory report for : 库存表368.Manpower/Tact estimation 工时预算369.Calibration : 校验370.Corrugated pad : 波纹垫371.C onductive bag : 保护袋372.Fixture : 制具373.Probe : 探针374.Lint-free gloves : 静电手套375.Wrist wrap : 静电手环376.plug hole孔塞377.Wrong direction 极性反ponent damage or broken 零件破损379.Unmeleted solder熔锡不良380.flux residue松香残渣381.w rong label or upside down label贴反382.mixed parts机种混装383.poor solder mask绿漆不良384.氧化Oxidization385.刮花Scratch386.脏污Contamination387.变形Deformation388.stand off height浮高389.IC reverse IC反向390.supervisor课长391.F orman组长392.R.T.Y: Rolled throughout yield直通率393.PPM: Parts per million 不良率394.DPU: Defects per unit 单位不良率395.Resistor: 电阻396.Capacitor:电容397.Resistor array : 排阻398.Capacitor array: 排容399.DIODE: 二极管400.triode: 三极管401.C rystal:震荡器402.Fuse:保险丝403.Bead: 电感inductor404.Connector:连结器405.Metal Shearing:裁剪406.ERP: Enterprise Resource Planning 企业资源规划407.Processed material: 流程性材料408.Corrective action:纠正措施409.Preventive action:预防措施410.P DCA:Plan/Do/Check/Action计划/实施/检查/处理411.Oscillator:振荡器412.A dapter: 适配器413.S pindle:轴心414.W IP: Work in process半成品Waive:特别采用415.F MEA:Protentical Failure Mode and Effects Analysis失效模式与效应分析416.M SA: Measurement Systems Analysis 量测系统分析417.B enchmarking:竞争标竿418.Roka Yoke 防错法419.Mistake Proofing 防呆法420.Fool-Proof System防呆系统421.Specified Requirement:规定要求422.AOQ: Average Outgoing Quality 平均检出质量AOQL: Average OutgoingQuality Limit 平均检出质量界限423.Benchmarking 基准点424.Calibration 校准425.Continuous improvement 持续改进426.Deviation / Substitution 偏差/ 置换427.ESD: Electrostatic discharge 静电释放428.FMEA: Failure Mode Effect Analysis失误模式效应分析429.First Article approval 产品的首次论证430.First pass yield 一次性通过的成品率431.F irst sample inspection 第一次样品检验432.FMECA: Failure mode effect and critically analysis 失误模式,效应及后果分析433.Life Testing 寿命试验Lot traceability 批量可追溯性434.NONCONFORMANCE 不符合435.OUT-OF-CONTROL PROCESS 失控工序436.Pilot Application 试产(试用)437.PPM: Parts per million 百万分之一438.Process capability index 工序能力指数439.Total quality management 全面质量管理440.Site Audit 现场审核441.F ailure rate percentage 失误百分率442.Customer complaints 客户投诉443.Root cause analysis of failures 失误根原分析yout Inspection:全尺寸检验445.Bulk material:散装材料446.Feasibility Reviews:可行性审查447.Pre-launch:量产前448.Stock rotation :存货周转449.Inventory levels:最低库存量450.Interim action:临时措施451.P ermanent action:永久措施452.vibration test振动试验453.Conveyer流水线物料板454.fasten锁紧(螺丝)455.fuse machine热熔机456.SOP制造作业程序457.work cell工作间458.trolley台车459.carton纸箱460.电阻Resistor461.电容Capacitor462.晶振Crystal resonator463.开关Switch 464.插座Jack465.插头Plug466.工艺Workmanship467.喷油Conformal coating468.插件Insertion469.回焊炉Reflowing oven470.飞达feeder471.吸嘴472.钢网Stencil473.抛料474.线股Strand475.松香Flux476.尾数WP477.锡炉DIP478.暂置Hold479.全检Sorting480.条形码Bar code481.日期编码Date code482.标准作业指导书SOP Standard operation plan483.过电压保护OVP Over voltage protect 484.汶波/噪声Noise485.连接器Connector 486.线材Cable487.CTQ=critical to quality。
电子行业专业词汇术语(专业超全)
电子行业专业词汇术语(专业超全)————————————————————————————————作者：————————————————————————————————日期：电子行业专业词汇术语GRR Gauge Repeatability Reproducibility 量测的再现性与再生性FPI First Piece Inspection 首件检查Sampling without replacement 不放回抽样SQA: Source(Supplier) Quality Audit 供货商品质审核1. QC : quality control 质量管理2. IQC : incoming quality control 进料质量管理3. OQC : output quality control 出货质量管理4. PQC : process quality control 制程质量管理也称IPQC : in process quality control .5. AQL : acceptable quality level 允收标准6. CQA: customer quality assurance 客户品质保证7. MA : major defeat 主要缺点8. MI : minor defeat 次要缺点9. CR :critical defeat 关键缺点10. SMT : surface mounting technology表面粘贴技术11. SMD :surface mounting device 表面粘贴程序SMC : surface mounting component 表面粘贴组件12.ECN : engineering change notice 工程变更通知13.DCN : design change notice 设计变更通知14.PCB : printed circuit board 印刷电路板15.PCBA : printed circuit board assembly装配印刷电路板16. BOM : bill of material 材料清单17. BIOS : basically input and output system基本输入输出系统18. MIL-STD-105E : 美国陆军标准,也称单次抽样计划.19. ISO : international standard organization 国际标准化组织20. DRAM: 内存条21. Polarity : 电性22. Icicles : 锡尖23. Non-wetting : 空焊24. Short circuit : 短路25. Missing component : 缺件26. Wrong component :错件27 . Excess component :多件28. Insufficient solder : 锡少29 . Excessive solder :锡多30. Solder residue: 锡渣31. Solder ball : 锡球32. Tombstone : 墓碑33 . Sideward：侧立34. Component damage :零件破损35. Gold finger:金手指36. SOP : standard operation process 标准操作流程37. SIP : standard inspection process 标准检验流程38 .The good and not good segregation :良品和不良品区分39. OBW : on board writer 熸录BIOS40 . Simple random sampling : 简单随机抽样41. Histogram : 直方图42 . Standard deviation : 标准差43. CIP : Continuous improvement program 持续改善计划44. SPC : Statistical process control 制程统制45 . Sub-contractors : 分包商46. SQE: Supplier quality engineering 47. Sampling sample :抽样计划48. Loader : 治具49. QTS: Quality tracking system 质量追查系统50. Debug : 调试51. Spare parts: 备用品52. Inventory report for : 库存表53. Manpower/Tact estimation 工时预算54. Calibration : 校验55. S/N :serial number 序号56. Corrugated pad : 波纹垫57.Takeout tray: 内包装盒58. Outer box : 外包装箱59. Vericode : 检验码60. Sum of square : 平方和61. Range : 全距62. Conductive bag : 保护袋63. Preventive maintenance :预防性维护64. Base unit : 基体65. Fixture : 制具66. Probe : 探针67. Host probe : 主探针68. Golden card : 样本卡69. Diagnostics program : 诊断程序70. Frame : 屏面71. Lint-free gloves : 静电手套72 .Wrist wrap : 静电手环73. Target value : 目标值74. Related department : 相关部门75. lifted solder 浮焊76.plug hole孔塞77. Wrong direction 极性反ponent damage or broken 零件破损79.Unmelted solder熔锡不良80.flux residue松香未拭81.wrong label or upside down label贴反82. mixed parts机种混装83. poor solder mask绿漆不良84. oxidize 零件氧化85.stand off height浮高86. IC reverse IC反向87.supervisor课长88. Forman组长89. WI=work instruction作业指导90. B.P. 非擦除状态91. Internal notification: 内部联络单92. QP :Quality policy质量政策93. QT: Quality target 品质目标94. Trend:推移图95.Paret柏拉图96. UCL: Upper control limit管制上限97.LCL:Lower control limit管制下限98. CL: Center line中心线99.R.T. Rolled throughout yield直通率100. PPM: Parts per million 不良率101.DPU: Defects per unit 单位不良率102.Resistor: 电阻103.Capacitor:电容104. Resistor array : 排阻105. Capacitor array: 排容106. DIODE: 二极管107.SOT: 三极管108. Crystal:震荡器109.Fuse:保险丝110.Bead: 电感inductance 111.Connector:联结器112.ADM: Administration Department行政单位113. CE: Component Engineering零件工程114. CSD :Customer Service Department客户服务部115. ID: Industrial Design工业设计116.IE: Industrial Engineering工业工程117. IR: Industrial Relationship工业关系118. ME: Mechanical Engineering机构工程119. MIS :Management Information System信息部120. MM: Material Management资材121. PCC: Project Coordination/Control专案协调控制122. PD: Production Department生产部123. PE: Product Engineering产品工程124. PM: Product Manager产品经理125. PMC: Production Material Control生产物料管理126. PSC: Project Support & Control产品协调127. Magnesium Alloy:镁合金128. Metal Shearing:裁剪129.CEM:Contract Electronics Manufacturing电子制造服务企业EMS: Electronics Manufacturing Services130. ERP: Enterprise Resource Planning 企业资源规划SCM+CRM+ERP+EAI=Network direct TM links procurement, production, Logistics and sales采购,生产,后勤管理及市场营销的融合EAI: Enterprise application Integration 企业应用系统整合CRM: Customer Relationship Planning 客户服务规划SCM : Supply chain management 供应链管理131. OJT: On job training 在职培训132.Access Time: 光盘搜寻时间133. B2CEC:Business to consumer electronic commerce 企业对消费者的电子商务B2BEC:Business to business electronic Commerce 企业间的电子商务L:Copper Clad Laminate 铜箔基板135. Intranet: 企业内部通讯网路136. ISP: Internet Service Provider网络服务提供者ICP: Internet Content Provider网络内容提供者137. GSM: Global System for Mobile Communication 泛欧数字式行动电话系统GPS: 全球卫星定位系统138. Home Page: 网络首页139.Video Clip:影像文件140. HTML:超文标记语言141.Domainname: 网域名称142. IP: 网络网域通讯协议地址143.Notebook:笔记型计算机144. VR: Virtual Reality虚拟实境145. WAP: Wireless Application Protocol无线应用软件协议146. LAN : Local area network局域网络WW World Wide Web世域网W AN: Wide Area Network 广域网络147. 3C: Computer, Communication, Consumer electronic 计算机, 通讯, 消费性电子三大产品的整合rmation Supplier Highway:信息高速公路149.UPS:Uninterrupted power system不断电系统150.Processed material: 流程性材料151.Entity/Item:实体152.Quality loop:质量环153.Quality losses: 质量损失154.Corrective action:纠正措施155. Preventive action:预防措施156.PDCAlan/Do/Check/Action计划/实施/检查/处理157. Integrated circuits(IC):集成电路158.Application program: 应用程序159.Utilities:实用程序160.Auxiliary storage/Second storage:;辅助存储器161.Silicon chip:硅片162Diskette drive:软驱163.Display screen/Monitor:显示器164.Foreground:前面165.Montherboard:母板166.Mermory board: 内存板167.Slot:插槽168.Busata-bus/address-bus/Control bus: 总线/数据总线/地址总线/控制总线169.Plotter:绘图170.MPC:Multimedia personal computer多媒体171.Oscillator:振荡器172.Automatic teller terminal:自动终端(出纳)机173.Joystick port:控制端口174.VGA: Video Graphics Array显示卡175.Resolution:分辨率176.Register:寄存器177.ISA: Industry Standard Architecture 工业标准结构178.EISA: Extended Industry Architecture 扩展工业标准结构179.Adapter: 适配器180.Peripheral:外部设备181.Faxmodem:调制解调器181.NIC:Network interface card网络接口卡182. SCSI: Small computer system interface 183.VESA: Video Electronic Standards Association184. SIMM: Single in-line memory module 单排座存储器模块(内存条) 185.Casing:外箱186.Aluminum:铝质187.Ceramic: 陶瓷的188.Platter:圆盘片189.Actuator:调节器190.Spindle:轴心191.Actuation arm: 存取臂192.Default code: 缺省代码193.Auxiliary port:辅助端口194.Carriage return : 回车195.Linefeed:换行197.Video analog: 视频模拟196.ASCII: American Standard Code for Information Interchange美国信息互换标准代码198.TTL: Transistor- Transistor logic晶体管-晶体管逻辑电路199.Three-prong plug:三芯电插头200.Female connector:连接插座201.Floppy disk:软盘202.Output level: 输出电平203.V ertical/Horizontal synchronization: 场/行同步204.H(Horizontal)-Phase:行相位patible:兼容机206.Hardware Expansion Card: 硬件扩充卡207.Buffer:缓冲208.CRM:Customer relationship Management 客户关系管理209.WIP: Work in process半成品210.Waiver:特别采用211.CXO系列—CEO: Chief Executive Office 首席执政官；执行总裁COO: Chief Operating OfficeCFO: Chief Finance OfficerCBO: Chief Business OfficerCTO: Chief Technology OfficerCIO: Chief Information OfficerCGO: Chief Government Officer212. NASDAQ: 纳斯达克证券市场NASDAQ Automated Quotation system213.VC: Venture Capital 风险投资214. PDA: Personal Date Assistant个人数字助理PLA: Personal Information Assistant个人信息助理215. PPAP: Advanced Product Quality Planning and Control Plan 生产性零组件核准程序216. FMEA: Potential Failure Mode and Effects Analysis 失效模式与效应分析217. MSA: Measurement Systems Analysis 量测系统分析218. QAS: Quality System Assessment 质量系统评鉴219. Cusum: 累计总合图220. Overall Equipment Effectiveness设备移动率221. Benchmarking: 竞争标杆Analysis of motion/Ergonomics动作分析/人体工程学222. Roka Yoke 防错法MCR: machine capability ratio 机器利用率223. Mistake Proofing 防呆法Taguchi methods田口式方法224, Vertical integration垂直整合Surveillance定期追踪审查225. EMS: Electronics Manufacturing Supply-chain226. Cause & Effects charts特性要因图227. Scatter: 散布图Fool-Proof System 防呆系统228. VE: Value Engineering 价值工程QFD: Quality Function Development 质量机能展开229. Arrow Chart 箭头图法Affiliate Chart亲和图法230. PDPC: Process Decision Program Chart System Chart系统图法231. Relation Chart 关边图法Matrix Chart矩阵图法232. Matrix Data Analysis 矩阵数据分析法234. Brain-storm 脑风暴法JIT: Just In Time:及时性生产模拟235. Deming Prize: 戴明奖Prototype技术试作236. BPM: Business Process Management 业务流程管MBO目标管理237. MBP:方针管理FTA:故障树分析QSC 服务质量238. IPPB: Information 情况planning策划Programming规划Budget预算239. EQ: Emotion Quotient:情商IQ: Intelligence Quotient:智商240. Implied Needs:隐含要求Specified Requirement:规定要求241. Probation:观察期Incoming Product released for urgent production 紧急放行242.Advanced quality planning 先进的质量策划243. AOQ: Average Outgoing Quality 平均检出质量AOQL: Average Outgoing Quality Limit 平均检出质量界限244.Approved Supplier List 经核准认可的供应商名单245.Attribute date 特征Benchmarking 基准点Calibration 校准246.Capable process工序能力Capability Index序能力指数Capability ratio工序能力率247.CHANG CYCLE TIME 修改的时间周期Continuous improvement 持续改进248. Control plans控制策划Cost of quality 质量成本249. Cycle time reduction减少周期时间250. Design of experiments 实验设计Deviation / Substitution偏差/置换251. ESD: Electrostatic discharge静电释放252. EH&S: Environmental, Health, and Safely 环境,健康.安全253. ESS: Environmental Stress Screening 环境应力筛选254. FMEA: Failure Mode Effect Analysis 失误模式效应分析255. First Article approval 产品的首次论证256. First pass yield 一次性通过的成品率257. First sample inspection第一次样品检验258. FMECA: Failure mode effect and critically analysis 失误模式,效应及后果分析259. Gauge control 测量仪器控制260. GR&R: Gauge repeatability and reproducibility 测量仪器重复性和再现性261. HALT: Highly Accelerated Life Test 高加速寿命试验262. HAST: Highly Accelerated Stress Test 高加速应力试验263. IN-CONTROL PROCESS 受控制工序264. INDUSTRIAL AVERAGE 工业平均数265. JIT (just in time) manufacturing (实时)制程266. Key characteristic关健特征267. Key component关健构件268. Life Testing寿命试验269. Lot traceability 批量可追溯性270. Material review board原材料审查部门MCR: machine capability ratio机械能力率271. NONCONFORMANCE不符合272. OUT-OF-CONTROL PROCESS失控工序273. Pilot Application试产(试用) 274. PPM: Parts per million百万分之一275. Preventive VS detection预防与探测Preventive maintenance预防维护276. Process capability index工序能力指277. Process control工序控制278. Process improvement工序改进279. Process simplification 过程简化280. Quality Clinic Process Chart (QCPC)质量诊断过程图281. Quality information system质量资料体系282. Quality manual质量手册283. Quality plan质量计划284. Quality planning质量策划285. Quality policy质量方针286. Quality system质量体系287. Reliability可靠性RUN Chart趋势表288. Skill Matrix技能表289. Statistical quality control (SQC)统计质量控制290. Teamwork 团队工作291. Total quality management全面质量管理292. Variable data变量数据293. Variation影响变量294. Value Analysis值分析295. Visual Factory形象化工厂296. Survey Instructions调查指引297. Profile 概况298. Improvement Plan改进计划299. Evaluation评估300. implementation实施301. Compliance符合302. Supplier Audit Report供方审核报告303. Site Audit现场审核304. Typical agenda典型的议事日程305. Internal and external failure costs内部和外部的失误成本306. Failure rate percentage 失误百分率307. Productivity (output / input)生产率(产出/投入) 308. Customer complaints 客户投诉309. Customer satisfaction indices 客户满意度指数310. Root cause analysis of failures失误根原分析品管中英文名词对照表Accuracy准确度Active主动Action评价.处理Activity活动Add加Addition rule加法运算规则Analysis Covariance协方差分析Analysis of Variance方差分析Appraisal Variation评价变差Approved承认ASQC美国质量学会Attribute计数值Audit审核Automatic database recovery数据库错误自动回复Average平均数balance平衡Balance sheet资产负债对照表Binomial二项分配Body机构Brainstorming Techniques脑力风暴法Business Systems Planning企业系统规划Cable电缆Capability能力Cause and Effect matrix因果图.鱼骨图Center line中心线check检查Check Sheets 检查表Chi-square Distribution 卡方分布Clutch spring 离合器弹簧Coining 压印加工Common cause 共同原因Complaint 投诉Compound factor 调合因素Concept 新概念Condenser 聚光镜Conformity 合格Connection 关联Consumer’s risk 消费者之风险Control 控制Control characteristic 管制特性Control chart 管制图Control plan 管制计划Correction 纠正Correlation Methods 相关分析法Cost down 降低成本CPI: continuouse Process Improvement 连续工序改善Creep 渐变Cross Tabulation Tables 交*表CS: customer Sevice 客户中心Cushion 缓冲Customer 顾客DSA: Defects Analysis System 缺陷分析系统Data 数据Data Collection 数据收集Data concentrator 资料集中缓存器DCC: Document Control Center 文控中心Decision 决策.判定Defects per unit 单位缺点数Description 描述Detection 难检度Device 装置Digital 数字Do 执行DOE: Design of Experiments 实验设计Element 元素Else 否则Engineering recbnology 工程技术Entropy 函数Environmental 环境Equipment 设备Estimated accumulative frequency 计算估计累计数E Equipment Variation 设备变异Event 事件External Failure 外部失效,外部缺陷FA: Failure Analysis 坏品分析Fact control 事实管理Fatique 疲劳FMEA: Failure Mode and Effect analysis 失效模式与效果分析FPY 合格率FQA: Final Quality Assurance 最终品质保证FQC: Final Quality control 最终品质控制Full-steer完全转向function职能Gauge system量测系统Grade等级Gum-roll橡皮滚筒Health meter体重计Heat press冲压粘着Histogram直方图Hi-tech高科技hypergeometric超几何分配hysteresis磁滞现象Improvement改善Inductance电感Information信息Initial review先期审查Inspection检验Internal Failure内部失效,内部缺陷IPQC: In Process Quality Control制程品质控制IQC: Incomming Quality Control来料品质控制IS International Organization for Standardization国际标准组织Law of large number大数法则Link连接LCL: Lower Control limit管制下限LQC: Line Quality Control生产线品质控制LSL: Lower Size Limit规格下限Machine机械Manage管理Materials物料Measurement量测Median中位数Miss feed漏送Module,sub-system,sub-unit单位Momentum原动力Monte garlo method原子核分裂热运动法MSA: Measurement System Analysis量测系统分析Multiplication rule乘法运算规则NIST 美国:标准技术院Normal常态分布Occurrence发生率On.off system开,关系统Operation Instruction作业指导书Organization组织Parameter参数Parto柏拉图Parts零件Parts per million不良率Passive消极的,被动的Plan计划Pulse 脉冲Policy 方针Population 群体Power 力量,能源PQA: Process Quality Assurance 制程品质保证Practice 实务Precision 精密度preemptive 先占式多任务Pressure 压缩Prevention 预防Probability 机率Probability density function 机率密度函数Procedure 流程Process 过程Process capability analysis制程能力分析图Process control and process capability制程管制与制程能力Producer’s risk生产者之风险Product产品Production生产Program方案Projects项目QA: Quality Assurance品质保证QC: Quality Control品质控制QE: Quality Engineering品质工程QFD: Quality Function Desgin品质机能展开Quality质量Quality manual品质手册Quality policy品质政策Random experiment随机试验Random numbers随机数Range全距Record记录Reflow回流Reject拒收Repair返修Repeatusility再现性Reproducibility再生性Requirement要求Residual误差Response响应Responsibilities职责Review评审Reword返工Robustness稳健性Rolled yield直通率RPN: Risk Priority Number风险系数sample抽样,样本Sample space样本空间Sampling with replacement放回抽样Sampling without peplacement不放回抽样Scatter diagram散布图分析Scrap报废Screw螺旋Severity严重度Shot-peening微粒冲击平面法Simple random sampling简单随机取样Size规格SL: Size Line规格中心线Slip滑动Stratified random sampling分层随机抽样SOP: Standard Operation Procedure标准作业书SPC: Statistical Process Control统计制程管制Special cause特殊原因Specification规范SQA: Source(Supplier) Quality Assurance供货商品质保证Stage sampling分段随机抽样Standard Deviation标准差Sum of squares统计表supplier平方和System供方systematic sampling系统,体系Statistical tables系统抽样Taguchi-method田口方法Technical committees技术委员会Test piece测试片Theory原理Time stamp时间戳印Time-lag延迟Title 题Torque转矩Total求和TQC: Total Quality Control全面品质控制TQM: Total Quality Management全面品质管理Traceablity追溯Training培训Transaction processing and logging交易处理Trouble困扰Up and down上和下UCL: Upper Control Limit管制上限USL: Upper Size Limit规格上限V alidation确认Variable计量值Variance变异和Vector向量Verification验证Version版本VOC: voice of Customer客户需求VOE: V oice of Engineer工程需[转帖]电子行业相关的英语词汇-1 backplane 背板2 Band gap voltage reference 带隙电压参考3 benchtop supply 工作台电源4 Block Diagram 方块图5 Bode Plot 波特图6 Bootstrap 自举7 Bottom FET Bottom FET 8 bucket capcitor 桶形电容9 chassis 机架10 Combi-sense Combi-sense11 constant current source 恒流源12 Core Sataration 铁芯饱和13 crossover frequency 交叉频率14 current ripple 纹波电流15 Cycle by Cycle 逐周期16 cycle skipping 周期跳步17 Dead Time 死区时间18 DIE Temperature 核心温度19 Disable 非使能，无效，禁用，关断20 dominant pole 主极点21 Enable 使能，有效，启用22 ESD Rating ESD额定值23 Evaluation Board 评估板24 Exceeding the specifications below may result in permanent damage to the device, or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not implied. 超过下面的规格使用可能引起永久的设备损害或设备故障。
电子产品常用英语词汇
电子产品常用英语词汇本文档旨在提供一些常用的电子产品英语词汇，帮助您更好地理解和交流相关的技术和信息。
1. 电子设备（Electronic Devices）：电子设备（Electronic Devices）：- 手机（Mobile Phone）- 平板电脑（Tablet）- 笔记本电脑（Laptop）- 数码相机（Digital Camera）- 平板电视（Smart TV）- 蓝牙耳机（Bluetooth Headphones）- 路由器（Router）- 打印机（Printer）- 游戏机（Game Console）2. 手机和平板电脑（Mobile Phones and Tablets）：手机和平板电脑（Mobile Phones and Tablets）：- 屏幕（Screen）- 触摸屏（Touchscreen）- 按钮（Button）- 扬声器（Speaker）- 麦克风（Microphone）- 摄像头（Camera）- 电池（Battery）- 存储空间（Storage）- Wi-Fi（Wi-Fi）- 蓝牙（Bluetooth）- 操作系统（Operating System）- 中央处理器（Central Processing Unit, CPU）- 内存（Memory）- 硬盘（Hard Drive）- 显卡（Graphics Card）- 鼠标（Mouse）- 键盘（Keyboard）- USB接口（USB Port）- 显示器（Monitor）- 网络（Network）4. 数码产品（Digital Products）：数码产品（Digital Products）：- 数字音乐播放器（MP3 Player）- 手持游戏机（Handheld Game Console）- 电子书阅读器（E-book Reader）- 可穿戴设备（Wearable Device）- 数码手表（Smart Watch）- 虚拟现实设备（Virtual Reality Device）- 无人机（Drone）- 智能家居设备（Smart Home Device）- 智能助理（Smart Assistant）- 人工智能（Artificial Intelligence）5. 网络和互联网（Internet and Networking）：网络和互联网（Internet and Networking）：- 网站（Website）- 网络连接（Internet Connection）- 浏览器（Browser）- 电子邮件（Email）- 社交媒体（Social Media）- 云存储（Cloud Storage）- 数据隐私（Data Privacy）- 信息安全（Information Security）- 虚拟专用网络（Virtual Private Network, VPN）- 数字版权（Digital Copyright）这些是一些常见的电子产品英语词汇，希望对您有所帮助！如果有任何问题或需要进一步的信息，请随时向我提问。
电子行业专业英语词汇
专用词汇表一、生产流程1.插机(刮蓝胶)component- inserting2.3.4.5.6.7.8.9.10.插件insection11.注塑plastic injection12.发料material delivery 13.插机14.零件加工component-processing15.炉前外观检查visual inspection beforewave soldering22.过水洗机23.打热熔胶dotting hot glue24.装卡板25.pallet栈板26.IC烧录IC program27.SMT(刮锡膏)28.喷油spray conformal coating29.30.31.32.33.34.35.36.to return material/stock to退料37.to fix a die装模38.to take apart a die拆模39.cold forging 冷锻40.press forging 冲锻41.to impose lines压线42.to compress, compressing压缩50.fit together组装在一起51.fasten锁紧(螺丝)52.rotating speed, revolution转速53.argon welding氩焊54.to take apart a die卸下模具55.to load a die装上模具56.to tight a bolt拧紧螺栓57.58.59.60.61.62.63.64.to pull, to stretch拉伸65.Line streching, line pulling线拉伸66.engraving, to engrave刻印67.degrease脱脂68.rinse水洗69.pierce die冲孔模70.forming die成型模78.吹热缩管79.胶芯plastic core二、夹具设备、工具80.烙铁iron81.排气扇A exhaust fan82.稀释剂a tinner83.水洗锡线84.85.86.87.88.89.90.91.roller 滚筒runner 流道92.plastic basket胶筐93.isolating plate baffle plate; barricade隔板94.steel plate钢板95.roll material卷料96.conveyer belt输送带97.transmission rack输送架105.静电手套ESD gloves 106.风枪air gun107.punch冲头108.groove punch压线冲子109.air vent排气道110.welding line熔合痕111.CONN Connector 连接器112.113.114.115.116.117.118.电磁阀Solenoid119.温控器Temperature control 120.烙铁发热芯heater core for iron 121.剪钳wire cutter122.电批开关Electric screw driver switch 123.电批Electric screw driver124.电批齿轮Electric screw driver gear132.烙铁座iron seat133.静电带wrist strap134.波峰锡炉wave soldering oven135.水循环系统water-recycling system 136.水洗机137.防水油conformal coating138.自动成型机auto-moulding machine 139.140.141.142.143.144.145.146.高周波塑料熔接机147.半自动锡浆印刷机148.剪线机149.超声波啤机ultrasonic welding machine 150.自动绕线机151.超声波清洗机ultrasonic cleaning machine159.焗炉160.进料器车161.锡浆搅拌机162.无铅波峰焊机163.开线机164.封口机165.胶纸机166.167.168.169.170.171.172.173.自动吸料机auto-sucking machine 174.锯床175.车床lathe 176.钻床177.punching machine 冲床178.干燥机drier179.冷水机cooler187.sheet metal parts 冲件188.punching machine 冲床189.过滤器filter190.碎料干燥机191.抽湿机192.热风回焊炉hot air reflow soldering oven193.194.195.196.197.198.199.200.真空杯vacuum cup201.真空咀vacuum tip202.喷嘴Nozzle 203.支架bracket204.六角板手hex.wrench 205.过滤器Filter 206.密封圈airproof ring214.线夹wire clamp 215.扎线tie wrap216.通风孔blowhole217.自功螺丝self-tapping screw 218.保险丝Fuse219.高度规High dividers 220.螺线管solenoid221.222.223.224.225.226.227.铝皮sheet aluminum 228.网络线communicate wire 229.电磁阀Solenoid AIRTAC 230.精调电阻Precision adjustable resisto 231.脚踏开关foot switch232.开关电源switching power233.散热片Thermal Conductive Pad241.除泡剂Defoamer242.继电器Relay243.电线束electrical wiring harness244.锡箔纸Solder foil papper245.针筒needle canister246.光电开关Photoelectricity switch 247.电批Electric screw driver248.249.250.251.252.253.254.255.flow board流水板256.vaccum cleaner吸尘器257.quenching淬火258.tempering回火259.annealing退火260.volatile挥发性261.风批Pneumatic driver进料质出货制程质量管理也称266.IPQC: in process quality control.267.AQL : acceptable quality level 允收标准268.CQA: customer quality assurance 客户质量保证269.PPM Parts Per Million 百万分之一270.271.272.273.274.粘贴组件275.ECN : engineering change notice 工程变更通知276.DCN : design change notice 设计变更通知277.BOM : bill of material 物料清单-STD-105E : 美国陆军标准,也称单次抽样计划.,教养锡尖286.torsion 扭曲287.warpage 翘曲288.waviness 波痕289.flying 飞件290.blister 起泡291.Short circuit : 短路292.冷焊cold soldering 293.294.295.296.297.298.299.300.Splay mark?水纹301.icicle/solder projection拉尖302.Flow mark?流纹303.White patches on surface?表面白斑304.Sink marks?缩影305.Mold release?脱模306.焊盘soldering tray314.Tombstone : 墓碑315.breaking.(be)broken,(be)cracked 断裂316.Sideward : 侧立317.cosmetic defect外观不良318.mixed color杂色319.die repair模修320.rust生锈321.322.323.324.325.326.327.328.reverse angle = chamfer倒角329.failure, trouble故障330.dents压痕331.defective upsiding down抽芽不良332.defective to staking铆合不良333.embedded lump镶块334.feeding is not in place送料不到位341.speckle斑点342.dimension/size is a little bigger尺寸偏大(小)343.not up to standard不合规格out of specification344.shrinking/shrinkage缩水345.mixed color杂色346.347.348.349.350.351.352.353.exposed metal/bare metal金属裸露ck of painting烤漆不到位ponent damage : 零件破损356.Gold finger : 金手指357.SOP : standard operation process 标准操作流程358.SIP : standard inspection process 标准检365.QTS: Quality tracking system 质量追查系统366.Spare parts :备用品367.Inventory report for : 库存表368.Manpower/Tact estimation 工时预算369.Calibration : 校验370.Corrugated pad : 波纹垫371.372.373.374.375.376.377.ponent damage or broken 零件破损379.Unmeleted solder熔锡不良380.flux residue松香残渣381.wrong label or upside down label贴反382.mixed parts机种混装383.poor solder mask绿漆不良391.Forman组长392.PPM: Parts per million 不良率393.DPU: Defects per unit 单位不良率394.Resistor: 电阻395.Capacitor:电容396.Resistor array : 排阻397.Capacitor array: 排容398.399.400.401.402.403.404.405.ERP: Enterprise Resource Planning 企业资源规划406.Processed material: 流程性材料407.Corrective action:纠正措施408.Preventive action:预防措施409.PDCA:Plan/Do/Check/Action计划/实施/检查/处理量测系统分析416.Benchmarking:竞争标竿417.Roka Yoke 防错法418.Mistake Proofing 防呆法419.Fool-Proof System防呆系统420.Specified Requirement:规定要求421.AOQ: Average Outgoing Quality422.423.424.425.426.ESD: Electrostatic discharge 静电释放427.FMEA: Failure Mode Effect Analysis 失误模式效应分析428.First Article approval 产品的首次论证429.First pass yield 一次性通过的成品率430.First sample inspection 第一次样品失控435.Pilot Application 试产(试用)436.PPM: Parts per million 百万分之一437.Process capability index 工序能力指数438.Total quality management 全面质量管理439.Site Audit 现场审核440.Failure rate percentage 失误百分率441.Customer complaints 客户投诉442.443.444.445.446.447.448.Inventory levels:最低库存量449.Interim action:临时措施450.Permanent action:永久措施451.vibration test振动试验452.Conveyer流水线物料板453.fasten锁紧(螺丝) 454.fuse machine热熔机462.开关Switch463.插座Jack464.插头Plug465.工艺Workmanship466.喷油Conformal coating 467.插件Insertion468.回焊炉Reflowing oven 469.470.471.472.473.474.475.476.锡炉DIP477.暂置Hold478.全检Sorting 479.条形码Bar code480.日期编码Date code481.标准作业指导书SOP Standard operation plan。
(完整版)电子产品字母缩写
(完整版)电子产品字母缩写本文档汇总了常见的电子产品字母缩写，方便大家更好地理解和使用电子产品时的技术术语。
以下是详细内容：A- AC：交流电（Alternating Current）AC：交流电（Alternating Current）- AMD：超威半导体（Advanced Micro Devices）AMD：超威半导体（Advanced Micro Devices）B- BIOS：基本输入输出系统（Basic Input Output System）BIOS：基本输入输出系统（Basic Input Output System）- Bluetooth：蓝牙Bluetooth：蓝牙C- CPU：中央处理器（Central Processing Unit）CPU：中央处理器（Central Processing Unit）D- DDR：双倍数据速率（Double Data Rate）DDR：双倍数据速率（Double Data Rate）- DVD：数字多用途光盘（Digital Versatile Disc）DVD：数字多用途光盘（Digital Versatile Disc）E- ECC：纠错码（Error Correction Code）ECC：纠错码（Error Correction Code）- EEPROM：可擦写程序存储器（Electrically Erasable Programmable Read-Only Memory）EEPROM：可擦写程序存储器（Electrically Erasable Programmable Read-Only Memory）- EPR：可扩展可重用（Extensible and Reusable）EPR：可扩展可重用（Extensible and Reusable）F- FAQ：常见问题解答（Frequently Asked Questions）FAQ：常见问题解答（Frequently Asked Questions）- FAT：文件分配表（File Allocation Table）FAT：文件分配表（File Allocation Table）- FPS：帧率（Frames Per Second）FPS：帧率（Frames Per Second）G- GPS：全球定位系统（Global Positioning System）GPS：全球定位系统（Global Positioning System）- GPU：图形处理器（Graphics Processing Unit）GPU：图形处理器（Graphics Processing Unit）H- HDD：硬盘驱动器（Hard Disk Drive）HDD：硬盘驱动器（Hard Disk Drive）I- IC：集成电路（Integrated Circuit）IC：集成电路（Integrated Circuit）- IDE：集成开发环境（Integrated Development Environment）IDE：集成开发环境（Integrated Development Environment）- IoT：物联网（Internet of Things）IoT：物联网（Internet of Things）- IPS：广角（In-Plane Switching）IPS：广角（In-Plane Switching）L- LCD：液晶显示器（Liquid Crystal Display）LCD：液晶显示器（Liquid Crystal Display）- LED：发光二极管（Light Emitting Diode）LED：发光二极管（Light Emitting Diode）- LTE：长期演进（Long-Term Evolution）LTE：长期演进（Long-Term Evolution）M- MP3：MPEG音频层3（MPEG Audio Layer 3）MP3：MPEG 音频层3（MPEG Audio Layer 3）NO- OLED：有机发光二极管（Organic Light Emitting Diode）OLED：有机发光二极管（Organic Light Emitting Diode）- OS：操作系统（Operating System）OS：操作系统（Operating System）P- PDF：便携式文档格式（Portable Document Format）PDF：便携式文档格式（Portable Document Format）- PPI：像素密度（Pixels Per Inch）PPI：像素密度（Pixels Per Inch）R- RAM：随机访问存储器（Random Access Memory）RAM：随机访问存储器（Random Access Memory）- ROM：只读存储器（Read-Only Memory）ROM：只读存储器（Read-Only Memory）- RSS：聚合内容（Really Simple Syndication）RSS：聚合内容（Really Simple Syndication）S- SD：安全数字卡（Secure Digital Card）SD：安全数字卡（Secure Digital Card）- SQL：结构化查询语言（Structured Query Language）SQL：结构化查询语言（Structured Query Language）- SSD：固态硬盘（Solid State Drive）SSD：固态硬盘（Solid State Drive）T- TCP/IP：传输控制协议/因特网协议（Transmission Control Protocol/Internet Protocol）TCP/IP：传输控制协议/因特网协议（Transmission Control Protocol/Internet Protocol）U- UI：用户界面（User Interface）UI：用户界面（User Interface）- USB：通用串行总线（Universal Serial Bus）USB：通用串行总线（Universal Serial Bus）V- VGA：视频图形阵列（Video Graphics Array）VGA：视频图形阵列（Video Graphics Array）- VPN：虚拟专用网络（Virtual Private Network）VPN：虚拟专用网络（Virtual Private Network）W- WLAN：无线局域网（Wireless Local Area Network）WLAN：无线局域网（Wireless Local Area Network）以上为电子产品常见字母缩写的完整列表。
电子行业电子产品英文术语大全
电子行业电子产品英文术语大全1. IntroductionIn the electronic industry, there are numerous terms and acronyms used to describe different electronic products and technologies. This comprehensive guide ms to provide a thorough list of commonly used English terms and acronyms in the electronic industry. Understanding these terms is essential for professionals and enthusiasts in this field.2. Common Terms and AcronymsHere is a detled breakdown of various terms and acronyms used in the electronic industry: 2.1 Analog•ADC: Analog-to-Digital Converter•AGC: Automatic Gn Control•DAC: Digital-to-Analog Converter•OP-AMP: Operational Amplifier•PWM: Pulse Width Modulation2.2 Digital•ASIC: Application-Specific Integrated Circuit•CPU: Central Processing Unit•DSP: Digital Signal Processor•FPGA: Field Programmable Gate Array•RAM: Random Access Memory•ROM: Read-Only Memory•UART: Universal Asynchronous Receiver Transmitter2.3 Power Supply•AC: Alternating Current•DC: Direct Current•PSU: Power Supply Unit•SMPS: Switched-Mode Power Supply •UPS: Uninterruptible Power Supply 2.4 Components•LED: Light Emitting Diode•IC: Integrated Circuit•PCB: Printed Circuit Board•LCD: Liquid Crystal Display•OLED: Organic Light Emitting Diode•SMD: Surface Mount Device•BGA: Ball Grid Array2.5 Communication•UART: Universal Asynchronous Receiver Transmitter•SPI: Serial Peripheral Interface•I2C: Inter-Integrated Circuit•CAN: Controller Area Network•USB: Universal Serial Bus•LAN: Local Area Network•WLAN: Wireless Local Area Network•Bluetooth: Bluetooth Wireless Technology2.6 Sensors•IR: Infrared•UV: Ultraviolet•PIR: Passive Infrared•MEMS: Micro-Electro-Mechanical Systems •IMU: Inertial Measurement Unit•LDR: Light Dependent Resistor2.7 Displays•LCD: Liquid Crystal Display•LED: Light Emitting Diode•TFT: Thin Film Transistor•OLED: Organic Light Emitting Diode•AMOLED: Active Matrix Organic Light Emitting Diode2.8 Connectivity•Wi-Fi: Wireless Fidelity•Bluetooth: Bluetooth Wireless Technology•NFC: Near Field Communication•GPS: Global Positioning System•RFID: Radio Frequency Identification •Zigbee: Low-power, low-data-rate wireless communication protocol2.9 Memory•ROM: Read-Only Memory•RAM: Random Access Memory•EPROM: Erasable Programmable Read-Only Memory•EEPROM: Electrically ErasableProgrammable Read-Only Memory•Flash: Flash Memory3. ConclusionThis list serves as a comprehensive reference for common terms and acronyms used in the electronic industry. It covers a wide range of topics including analog and digital, power supply, components, communication, sensors, displays, connectivity, and memory. Familiarizing oneself with these terms is crucial for individuals workingin the electronic field to effectively communicate and collaborate with others in the industry.。
电子产品英文术语大全
小组成立问题说明实施并验证临时措施确定并验证根本原因选择并验证永久纠正措施实施永久纠正措施预防再发生小组祝贺PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知)QAPS: Quality Assurance Process Sheet (品质工程表)DRP ：运销资源计划 (Distribution Resource Planning)DSS：决策支持系统 (Decision Support System)EC ：电子商务 (Electronic Commerce)EDI ：电子资料交换 (Electronic Data Interchange)EIS ：主管决策系统 (Excutive Information System)ＥＲＰ：企业资源规划 (Enterprise Resource Planning)FMS ：弹性制造系统 (Flexible Manufacture System)KM ：知识管理 (Knowledge Management)4L ：逐批订购法 (Lot-for-Lot)LTC ：最小总成本法 (Least Total Cost)LUC ：最小单位成本 (Least Unit Cost)MES ：制造执行系统 (Manufacturing Execution System)MPS ：主生产排程 (Master Production Schedule)MRP ：物料需求规划 (Material Requirement Planning)MRPⅡ：制造资源计划 (Manufacturing Resource Planning)OEM ：委托代工 (Original Equipment Manufacture)ODM ：委托设计与制造 (Original Design & Manufacture)OLAP：线上分析处理 (On-Line Analytical Processing)OLTP：线上交易处理 (On-Line Transaction Processing)OPT ：最佳生产技术 (Optimized Production Technology)PDCA：PDCA管理循环 (Plan-Do-Check-Action)PDM：产品数据管理系统 (Product Data Management)) RCCP：粗略产能规划 (Rough Cut Capacity Planning) SCM ：供应链管理 (Supply Chain Management)SFC ：现场控制 (Shop Floor Control)TOC：限制理论 (Theory of Constraints)TQC ：全面品质管制 (Total Quality Control)FYI/R:for your information/reference仅供参考ASAP:尽快S/T:Standard time标准时间TPM:total production maintenance：全面生产保养ESD Wrist strap：静电环IT:information technology信息技术，资讯科学CEO：Chief Executive Officer执行总裁COO：Chief Operaring Officer首席业务总裁SWOT：Strength,Weakness,Opportunity,Threat优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通Cooperation：统御融合Vibration Testing：振动测试IDP：Individual Development Plan个人发展计划MRP：Material Requirement Planning物料需求计划MAT'S：Material材料LRR：Lot Rejeet Rate批退率ATIN：Attention知会3C：Computer ,Communication , Consumer electronic 消费性电子5W1H：When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement人,机器,材料,方法,测量4MIE: Man,Material,Machine,Method,Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money , Information 人力，机器，材料，方法, 市场，管理，资金，资讯1 Accuracy 准确度2 Action 行动3 Activity 活动4 Analysis Covariance 协方差分析5 Analysis of Variance 方差分析6 Approved 承认7 Attribute 计数值8 Average 平均数9 Balance sheet 资产负债对照表10 Binomial 二项分配11 Brainstorming Techniques 脑力风暴法12 Cause and Effect Matrix 因果图(鱼骨图)13 CL:Center Line 中心线14 Check Sheets 检查表15 Complaint 投诉16 Conformity 合格（符合）17 Control 控制18 Control chart 控制(管制)图19 Correction 纠正20 Correlation Methods 相关分析法21 CPI: continuouse Process Improvement 连续工序改善22 Cross Tabulation Tables 交叉表23 CS: Customer Sevice 客（户）服（务）中心24 DSA: Defects Analysis System 缺陷分析系统25 Data 数据 Description:品名26 DCC: Document Control Center 文控中心27 Decision 决策、判定28 Defects per unit 单位缺点数29 Description 描述30 Device 装置31 Do 执行32 DOE: Design of Experiments 实验设计33 Element 元素34 Engineering recbnology 工程技35 Environmental 环境36 Equipment 设备37 Estimated accumulative frequency 计算估计累计数38 E Equipment Variation 设备变异39 External Failure 外部失效,外部缺陷40 FA: Failure Analysis 失效分析41 Fact control 事实管理42 Fatigue 疲劳43 FMEA: Failure Mode and Effect Analysis失效模式与效果分析44 FP First-Pass Yield （第一次通过）合格率45 FQA: Final Quality Assurance 最终品质保证46 FQC: Final Quality control 最终品质控制47 Gauge system 测量系统48 Grade 等级49 Histogram 直方图50 Improvement 改善51 Initial review 先期审查52 Inspection 检验53 Internal Failure 内部失效、内部缺陷54 IPQC: In Process Quality Control 制程品质控制55 IQC: Incomming Quality Control 来料品质控制56 IS International Organization for Standardization 国际标准化组织57 LCL: Lower Control limit 管制下限58 LQC: Line Quality Control 生产线品质控制59 LSL: Lower Size Limit 规格下限60 Machine 机械61 Manage 管理62 Materials 物料63 Measurement 测量64 Median 中位数65 MSA: Measurement System Analysis 测量系统分析66 Occurrence 发生率67 Operation Instruction 作业指导书68 Organization 组织69 Parto 柏拉图70 PPM arts per Million （百万分之）不良率71 Plan 计划72 Policy 方针73 Population 群体74 PQA: Process Quality Assurance 制程品质保证75 Practice 实务(践)76 Prevention 预防77 Probability 机率78 Probability density function 机率密度函数79 Procedure 流程80 Process 过程81 Process capability analysis 制程能力分析（图）82 Process control and Process capability制程管制与制程能力83 Product 产品84 Production 生产85 Projects 项目86 QA: Quality Assurance 品质保证87 QC: Quality Control 品质控制88 QE: Quality Engineering 品质工程89 QFD: Quality Function Desgin 品质机能展开(法)90 Quality 质量91 Quality manual 品质手册92 Quality policy 品质政策(质量方针)93 Random experiment 随机试验94 Random numbers 随机数95 R:Range 全距（极差）96 Reject 拒收97 Repair 返修98 Repeatusility 再现性99 Reproducibility 再生性100 Requirement 要求101 Responsibilities 职责102 Review 评审103 Reword 返工104 Rolled yield 直通率105 RPN: Risk Priority Number 风险系数106 Sample 抽样,样本107 Sample space 样本空间108 Sampling with replacement 放回抽样109 Sampling without replacement 不放回抽样110 Scatter diagram 散布图分析111 Scrap 报废112 Simple random sampling 简单随机取样113 Size 规格114 SL: Size Line 规格中心线115 Stratified random sampling 分层随机抽样116 SOP: Standard Operation Procedure 标准作业书117 SPC: Statistical Process Control 统计制程管制118 Specification 规范119 SQA: Source(Supplier) Quality Assurance 供货商品质保证120 Stage sampling 分段随机抽样121 Standard Deviation 标准差122 Sum of squares 平方和123 Taguchi-method 田口(试验)方法124 Theory 原理125 TQC: Total Quality Control 全面品质控制126 TQM: Total Quality Management 全面品质管理127 Traceablity 追溯128 Training 培训129 UCL: Upper Control Limit 管制（控制）上限130 USL: Upper Size Limit 规格上限131 Validation 确认132 Variable 计量值133 Verification 验证134 Version 版本135 VOC: Voice of Customer 客户需求136 VOE: Voice of Engineer 工程需求137 Inventory stock report:庫存清单报告138 Sales order report:出货报告质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproductiveness & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善小组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商) ECO Engineering Change Order 工程改动要求(客户) PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheet PDCS Process defect correcting sheet GRN Goods receiving noteA/R Accounting receivableA/P Accounting payable专业词汇通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长Human Resources Department人力资源部Head count 人头数production department生产部门planning department企划部QC Section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 计算机外壳(组件)personal computer enclosure 计算机机箱产品front plate前板rear plate后板chassis |'∫æsi| 基座Hood 上盖base pan 基座bezel 面板riser card 扩充卡flat cable 排线TOP driver cage 上磁架bottom driver cage 下磁架resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑料件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程窗体lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck 瓶颈模具工程类forming die成型模progressive die连续模stage die工程模compound die复合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 换模to fix a die装模to repair a die修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚upper supporting blank上承板upper padding plate blank上垫板top plate上托板（顶板）top block上垫脚stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子sliding block滑块sliding dowel block滑块固定块die locker锁模器pressure plate =plate pinch压板thickness gauge厚薄规cutting die, blanking die冲裁模die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条panel board镶块to load a die装上模具to unload a die 御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板trim剪外边pierce剪内边pocket for the punch head挂钩槽slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch =die button圆冲子shape punch =die insert异形子stock located block定位块metal plate钣金miller铣床grinder磨床tolerance公差score =groove压线sliding block滑块lathe车active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板capability能力driller钻床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves =spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板handle mold手持式模具flash mold溢流式模具positive mold挤压式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue, cont.连动to grip(material)吸料location lump, locating piece, location block定位块reset复位to file burr 锉毛刺embedded lump |in'bed| mp|镶块|lstamping-missing漏冲to tight a bolt拧紧螺栓to loosen a bolt拧松螺栓punched hole冲孔to cut edge =side cut =side scrap 切边to bending折弯to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake铆合designing, to design设计design modification 设计修改成pedal踩踏板stopper阻挡器flow board流水板torque扭矩spline =the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的forming成型(抽凸,冲凸)draw hole抽孔bending折弯emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线stamp letter冲字(料号)tick-mark nearside正面压印冲压类punch, press冲punching machine 冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management制造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包成型类insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口runner less无浇道sprue less 无射料管方式long nozzle延长喷嘴方式spur浇口;溶waste废料board广告牌sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理组装类Assembly line组装线Layout布置图Conveyer流水线运输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine/heat stake热熔机processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉organic solvent有机溶剂demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料volatile挥发性degrease脱脂rinse水洗alkaline etch龄咬desmot剥黑膜. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔scraped products报放品disposed products处理品dismantle the die折模auxiliary function辅助功能heater band 加热片thermocouple热电偶degate打浇口dryer烘干机induction感应induction light感应光response =reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线grit沙砾granule =pellet =grain细粒sand blasting喷沙grit maker抽粒机cushion缓冲fillet镶;嵌边roller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴品质类qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part来件不良exposed metal/bare metal金属裸露excessive defect过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格cosmetic defect外观不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑丝missing part漏件wrong part错件oxidation氧化defective threading抽芽不良poor staking铆合不良deficient purchase来料不良deficient manufacturing procedure制程不良cosmetic inspection外观检查inner parts inspection内部检查blister 气泡angular offset 角度偏差dent 压痕filings 铁削defective label 不良标签abrasion 磨损Breaking. (be)broken,(be)cracked 断裂short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delaminating起鳞speckle斑点mildewed =moldy = mouldy发霉deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage缩水mixed color杂色fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍failure, trouble 故障deformation 变形rust 生锈peel 脱漆Shrink 缩水Contamination 脏污water spots 水渍Gap 间隙label error 标签错误Missing label 漏贴rejection criteria 拒收标准Suspected rejects 可疑庇abrasion 损伤、磨损Texture surface 印花纹表面Streak 条纹stains 污点Blotch 斑点discoloration 脱色Inclusion 杂质slug mark 压痕dirt grime 灰尘blush 毛边薄膜sink 下凹Hickey 漏漆labels and logos 贴纸与商标corrugated container 瓦摆纸箱Delaminating 脱层splattering 散点Gouge 锉孔puckering 折痕品管七大手法层别法：stratification直方图：histogram柏拉图：plato diagram查检表：check sheet特性要因图：charateristic diagram散布图：scatter diagram管制图：control diagramPSW零部件提交保证书QSA质量体系评定QSR质量体系要求Analysis of motion/ergonomic 运动/人机工程学分析Corrective action纠正措施FEA有限元分析Initial process study初始过程研究Layout inspection 全尺寸检查Quality pian质量计划Quality pianing质量策划AAR外观件批准IATF国际汽车工作组为了协调国际汽车质量系统规范，由世界上主要的汽车制造商及协会于1996年成立了一个专门机构，称为国际汽车工作组International Automotive Task Force (IATF) 。
电子厂常用英语词汇.
电⼦⼚常⽤英语词汇.镊⼦: TWEEZERS 电容: CAPACITOR顺时针⽅向:CLOCKWISE锯⼦: SAW电阻: RESISTOR 逆时针⽅向: CONTERCLOCKWISE尖嘴钳: NOSE PLIER继电器: RELAY 振动测试: VIBRATION TEST扳⼿: SPANNER晶振: CRYSTAL 丝印:SPRAY-PAITING鎯头: HAMMER过滤器: FILTER 烫⾦:METAL-STAMPING电烙铁: SOLDERING IRON ⼆极管: DIODES 剪钳: WIRE CUTTER三极管: TRIODE ⽼虎钳: PLIERS 发光⼆极管: LIGHT EMITTING DIODE( LED)电批: TORQUE DRIVER松⾹: FLUX夹⼦: CLAMP松⾹笔: FLUX PEN 正极: ANODE END三⾓架: CROWFOOD 红胶⽔: EPOXYB ADHESIVE负极: CATHODE END钢⽹: STENCIL胶⽔: GLUE 硬化: CURING刮⼑: SQUEEGEE 贴纸: STICKER配线:WIRING⼑⽚: BLADE透明胶纸: OPP TAPE 冷却硬化: OVEN-CURING放⼤镜: VISIONSCOPE卡板: PALLET间距: PITCH调压器: BOOSTER ⼿推车: TROLLEYS周期:CIRCLETIME⽰波器: OSCILLOSCOPE烘⼲: BAKE 测试: DEBUG测试针: TOGGLE PINS紫外线: ULTRAVIOLET模拟: SIMULATION架⼦: RACK线圈: WINDING ⽑细管现象: CAPILLARY ACTION⽀架: BRACKETS 涂层: COATING导体:CONDUCTIVEPATTERN溶剂: SOVENT介质材料: DIELETRICMATERIAL隔热板: FELT 镀通孔: PTH( PLATED THROUGH HOLE)锡条: SOLDE BAR 不合格品: NONCONFIRMING UNITS锡膏: SOLDER PASTE原料: DIRECT MATERIAL氧化: OXIDE锡炉: SOLDER-POT 辅料: INDIRECTMATERIAL额定电源: RATEDPOWER浸锡:DIG-SOLDER 试产: PILOT PRODUCTION 量产: MASS PRODUCTION焊点: SOLDERING JOINTS X 光测试: X RAY TEST焊盘: PAD/LAND 跌打测试: DROP TEST焊接: WELDING⽼化测试: BURN-IN TEST 超声波焊接: ULTRASONIC WELDING回流焊接: REFLOW SOLDERING波峰焊接: WAVE SOLDERING 线路板; PCB(Printed Circuit Board)回焊前: PRE-REFLOW 线路板装配: PCBA( PRINTED CIRCUIT BOARD ASSEMBLY)回焊后: POST-REFLOW 集成电路:IC( INTERGRATED CIRCUIT)回流炉: REFLOW OVEN ESD: ELECTROSTATIC DISCHARGE: 静电放电虚焊: DEWETTING ESD PREVENTION&DAMAGE: 静电防护与损坏假焊: SHORT SOLDER FMEA: FAILURE MODE AND EFFECT ANALYSIS(失效模式分析)少锡: INSUFFICENT SOLDER SPC: STASTICAL PROCESS CONTROL(统计过程控制)偏位: MISALIGNMENT IPC: INSTITUTE OF PACKING AND INTERCONNECTS(电⼦电路互连与封装协会)阻焊剂:SOLDER-THIEF/MASK 注塑: INJECTION MOLDING层分: DELAMINATION线路: TRACE裂: CRACKED 浮起: LIFTING回路: CIRCUIT内翘: WARPED 静电防护: STATIC SHIELDING短路: BRIGING/SHORT 翘起: LIFT 散静电: STATIC DISSIPATIVE线路开路: BROKEN TRACE 弯: BOW 防静电: ANTISTATIC。
电子产品常用英文词汇
电子产品常用英文词汇一、常见电子电气类英文单词1.功率power2.电压voltage3.电流current4.频率frequency5.效率efficiency6.波形waveform7.交流alternating-current8.直流direct-current9.适配器 adaptor10. 转换器 converter11. 逆变器 inverter12. 充电器 charger13. 控制器 controller14. 启动器 jump starter15. 器件device16. 元件component17. 电容器capacitor18. 电阻resistor19. 电感inductor20. 二极管diode21. 稳压二极管 zener22. 三极管audion23. 场效应管 MOSFEET(Metel-Oxide-Semiconductor Field Effect Transistor)24. 变压器 transformer25. 光藕 optical coupler26. 保险丝 fuse27. 半导体semiconductor28. 瓷片电容 ceramic capacitor29. 电解电容 electrolytic C30. 电感 inductance31. 电容 capacitance32. 电阻 resistance33. 感性的 inductive34. 容性的 capacitive35. 阻性的 resistive36. 阻抗impedance37. 纯正弦波 pure sine wave38. 修正正弦波 modified sine wave39. 方波 square wave40. 恒流源 constant current source41. 恒压源 constant voltage source42. 纹波电流 ripple current43. 涌入电流 inrush current44. 空载电流 no-load current45. 电网 power system46. 死区时间dead time47. 浮充电压 float charge voltage48. 正向电压forward voltage drop49. 续流二极管 freewheel diode50. 肖特基二极管 schottky51. 整流桥 bridge rectifier52. 超快速整流器 ultra fast rectifier53. 检测电阻 sense resistor54. 振荡电阻 timing resistor55. 散热片thermal slug/heat sink/ radiator56. 断路器breaker57. 过流保护器 circuit breaker58. 自由运行 free running59. 满负载 full load60. 过载 overload61. 轻载 light load62. 加载 upload63. 静态 static （state）64. 动态 dynamic （state）65. 稳态的 steady66. 静电 static electricity67. 电源调整率line regulation68. 负载调整率load regulation69. 满载效率 full load efficiency70. 最佳效率 optimum efficiency71. 输出效率 output efficiency72. 峰值效率 peak efficiency73. 标称效率 declared efficiency74. 视在功率 apparent power75. 有功功率 active power76. 无功功率 reactive power77. 功率因数 power-factor78. 耗散功率 power dissipation79. 空载损耗 no-load loss80. 关断状态 off state81. 电源工作电压 operating supply voltage82. 电压参考 voltage reference83. 参考值 reference value84. 反馈feedback85. 产品型号part number86. 掉电power down87. 上电power up88. 电源正常 power good89. 欠压锁定 under voltage lock out (UVLO)90. 上拉 pull up91. 下拉 pull down92. 上升沿 rising edge93. 下降沿 falling edge94. 上限 upper limit95. 下限 lower limit96. 极性 polarity97. 藕合 coupling98. 故障 malfunction99. 原理图 schematic diagram100. 封装footprint101. 设计流程 design cycle102. 设计余量 design margin二、常用电源类英文缩写SPS： switching power supplyPWM: pulse width modulationZCS： zero current switchingZVT: Zero Voltage TransitionPFC: Power Factor CorrectionRMS: Root mean square （均方根）THD: Total Harmonic Distortion (总谐波失真)OVP: Over Voltage ProtectionOCP: Over Current ProtectionOTP: Over Temperature ProtectionMCU: Micro Controller unitTVS: Transient voltage suppressorPCB: Printed circuit boardSMT: surface mounting technologyECR: Engineering Change RequestECN: Engineering Change noticeFMEA: Failure Mode Efficiency AnalysisIC: integrated circuitIE: Industrial EngineeringIT: information technologyAQL: Acceptable Quality LevelQA: Quality AssuranceQC: Qualty ControlIQC: Incoming Quality controlIPQC: In- process Quality control三、变压器类常用材料1. 磁芯：magnetic core2. 骨架：bobbin3. 导线：wire4. 绝缘胶带：insulation tape5. 挡带: margin tape6. 铜箔： copper foil7. 磁环： annular core8. 铁氟龙套管：teflon tube9. 绝缘套管：empire tuble10. 凡立水：varnish11. 气隙：gap12. 绕组：winding13. 初级绕组：primary coil14. 次级绕组：secondary coil15. 电感量: inductance16. 漏感： Leakage inductance17. 耐压：HI-POT18. 绝缘电阻: insulation resistance19. 匝数：turns四、工艺工程类常用英文词汇1. 技术规范：technical regulation2. 规范：specification3. 检修技术：service technic4. 焊接工艺：bonding technology5. 表面安装：surface mounting6. 元件面：component side7. 焊接面：solder side8. 元件孔：component hole9. 安装孔：mounting hole10. 工艺流程图：engineering flow sheet11. 故障指示：failure indication12. 锡焊： tin-lead bonding13. 装配：assembly14. 接插件：socket connector15. 连接器：connector16. 端子：terminal17. 端子壳：housing18. 插座：socket19. 插座盖：socket cover20. 点烟座：cigarette lighter socket21. 点烟头：cigar plug22. 接线座：wire holder23. 接线端子：wire connecting terminal24. 接线器：wire connector25. 线材规格：wire gauge26. 电烙铁： electric solding iron27. 烙铁头：solder horn28. 焊锡： soldering tin29. 焊盘： Pad30. 无铅： Lead Free31. 波峰焊：wave soldering32. 回流焊：reflow soldering33. 老化：burn-in/aging34. 极性： Polarity35. 正级：Positive pole36. 负极：negative pole37. 硬件:hardware38. 软件：software39. 通风孔：vent40. 支撑架/轴承：bearing41. 工艺：technics42. 夹具：fixture43. 冲压模具：die44. 注塑模具：injection mould45. 材料：material46. 扭矩：torque47. 应力：stress48. 强度:strength49. 机壳：enclosure50. 紧固件：fastener51. 螺栓：bolt52. 螺母：nut53. 螺丝：screw54. 垫片：washer55. 套筒扳手：socket key/ socket spanner56. 剪钳：wire cutter57. 剥线皮钳：wire stripper58. 裁线机：wire shear59. 防护罩：guard60. 环氧树脂:epoxy resin61. 玻璃纤维：glass fiber62. 光面：shiny side63. 粗糙面：matte side64. 处理面：treated side。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
品质管理电子产品的英文术语大全从事品质工作以来积累的常用英语，希望对有需要的朋友有所帮助！品质专业英语大全零件材料类的专有名词CPU: central processing unit(中央处理器)IC: Integrated circuit(集成电路)Memory IC: Memory Integrated circuit（记忆集成电路）RAM: Random Access Memory（随机存取存储器）DRAM: Dynamic Random Access Memory（动态随机存取存储器）SRAM: Staic Random Access Memory（静态随机存储器）ROM: Read-only Memory（只读存储器）EPROM:Electrical Programmable Read-only Memory（电可抹只读存诸器）EEPROM: Electrical Erasbale Programmable Read-only Memory（电可抹可编程只读存储器）CMOS: Complementary Metal-Oxide-Semiconductor（互补金属氧化物半导体）BIOS: Basic Input Output System（基本输入输出系统）Transistor：电晶体LED:发光二极体Resistor：电阻Variator：可变电阻Capacitor:电容Capacitor array：排容Diode：二极体Transistor：三极体Transformer：变压器（ADP）Oscillator：频率振荡器（0sc）Crystal：石英振荡器XTAL/OSC:振荡产生器（X）Relay：延时器Sensor：感应器Bead core：磁珠Filter:滤波器Flat Cable：排线Inductor：电感Buzzer：蜂鸣器Socket：插座Slot：插槽Fuse：熔断器Current：电流表Solder iron：电烙铁Magnifying glass：放大镜Driver：螺丝起子Oven：烤箱TFT:液晶显示器Oscilloscope：示波器Connector：连接器PCB:printed circuit board（印刷电路板）PCBA: printed circuit board assembly（电路板成品）PP:并行接口HDD:硬盘FDD:软盘PSU:power supply unit（电源供应器）SPEC:规格Attach:附件Case: 机箱，盖子Cover：上盖Base：下盖Bazel：面板（panel）Bracket：支架，铁片Lable：贴纸Guide：手册Manual：手册，指南Card：网卡Switch：交换机Hub：集线器Router：路由器Sample：样品Gap：间隙Sponge：海绵Pallet：栈板Foam：保利龙Fiber：光纤Disk：磁盘片PROG:程序Barcode：条码System：系统System Barcode：系统条码M/B:mother board：主板CD-ROM:光驱FAN:风扇Cable：线材Audio：音效K/B:Keyboard（键盘）Mouse：鼠标Card reader：读卡器Screw：螺丝Thermal pad：散热垫Heat sink：散热片Rubber：橡胶垫Rubber foot：脚垫Bag：袋子Washer：垫圈Sleeve：袖套Config：机构Label hi-pot：高压标签Firmware label：烧录标签Metal cover：金属盖子Plastic cover：塑胶盖子Tape for packing：包装带Bar code：条码Tray：托盘Collecto：集线夹Holder：固定器,L铁Connecter：连接器IDE:集成电路设备，智能磁盘设备SCSI:小型计算机系统接口Gasket：导电泡棉AGP:加速图形接口PCI:周边组件扩展接口LAN:局域网USB:通用串形总线架构Slim：小型化COM:串型通讯端口LPT:打印口，并行口Power cord：电源线I/O:输入，输出Speaker：扬声器EPE:泡棉Carton：纸箱Button：按键，按钮Foot stand：脚架部门名称的专有名词QS:Quality system品质系统CS:Coutomer Sevice 客户服务QC:Quality control品质管理IQC:Incoming quality control 进料检验LQC:Line Quality Control ? 生产线品质控制IPQC:In process quality control 制程检验FQC:Final quality control 最终检验OQC:Outgoing quality control 出货检验QA:Quality assurance 品质保证SQA:Source(supplier) Quality Assurance 供应商品质保证(VQA) CQA：Customer Quality Assurance客户质量保证PQA rocess Quality Assurance 制程品质保证QE:Quality engineer 品质工程CE:component engineering零件工程EE:equipment engineering设备工程ME:manufacturing engineering制造工程TE:testing engineering测试工程PPE roduct Engineer 产品工程IE:Industrial engineer ? 工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC:producing control生管MC:mater control物管GAD: General Affairs Dept总务部A/D: Accountant /Finance Dept会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchaing Dept)SMT:Surface mount technology 表面粘着技术MFG:Manufacturing ? 制造MIS:Management information system 资迅管理系统DCC:document control center 文件管制中心厂内作业中的专有名词QT:Quality target品质目标QP:Quality policy目标方针QI:Quality improvement品质改善CRITICAL DEFECT:严重缺点（CR）MAJOR DEFECT:主要缺点（MA）MINOR DEFECT:次要缺点（MI）MAX:Maximum最大值MIN:Minimum最小值DIA iameter直径DIM imension尺寸LCL:Lower control limit管制下限UCL:Upper control limit管制上限EMI:电磁干扰ESD:静电防护EPA:静电保护区域ECN:工程变更ECO:Engineering change order工程改动要求（客户）ECR:工程变更需求单CPI:Continuous Process Improvement 连续工序改善Compatibility：兼容性Marking：标记DWG rawing图面Standardization：标准化Consensus：一致Code：代码ZD:Zero defect零缺点Tolerance：公差Subject matter：主要事项Auditor：审核员BOM:Bill of material物料清单Rework：重工ID：identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR：First Piece Inspection Report首件检查报告FAA:首件确认SPC：统计制程管制CP: capability index（准确度）CPK: capability index of process(制程能力)PMP:制程管理计划（生产管制计划）MPI:制程分析DAS efects Analysis System ? 缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N:料号L/N：Lot Number批号Version：版本Quantity：数量Valid date：有效日期MIL-STD：Military-Standard军用标准ICT: In Circuit Test (线路测试)ATE：Automatic Test Equipment自动测试设备MO: Manafacture Order生产单T/U: Touch Up (锡面修补)I/N:手插件P/T:初测F/T: Function Test (功能测试-终测)AS 组立P/K:包装TQM:Total quality control全面品质管理MDA:manufacturing defect analysis制程不良分析(ICT)RUN-IN:老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect高频测试DPPM: Defect Part Per Million(不良率的一种表达方式：百万分之一) 1000PPM即为0.1%Corrective Action: (CAR改善对策)ACC：允收REJ:拒收S/S：Sample size抽样检验样本大小SI-SIV：Special I-Special IV特殊抽样水平等级CON：Concession / Waive特采ISO:国际标准化组织ISA：Industry Standard Architecture工业标准体制结构OBA:开箱稽核FIFO:先进先出PDCA:管理循环Plan do check action计划，执行，检查，总结(计划，实施，检查，处置) WIP:在制品（半成品）S/O: Sales Order (业务订单)P/O: Purchase Order (采购订单)P/R: Purchase Request (请购单)AQL:acceptable quality level允收品质水准LQL;Limiting quality level最低品质水准QVL:qualified vendor list合格供应商名册AVL ：认可的供货商清单(Approved Vendor List)QCD: Quality cost delivery（品质，交期，成本）MPM:Manufacturing project management制造专案管理KPI:Key performance indicate重要绩效指标MVT:Manufacturing Verification Test制造验证试产Q/R/S：Quality/Reliability/Service质量/可靠度/服务STL:ship to line（料到上线）NTF:No trouble found误判CIP:capacity improvement plan（产能改善计划）MRB:material review board（物料审核小组）MRB:Material reject bill退货单JIT:just in time（即时管理）5S:seiri seiton seiso seiketsu shitsuke（整理，整顿，清扫，清洁，修养）SOP:standard operation process（标准作业程序）SIP:Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction（作业指导书）SMD:surface mounting device（表面粘着原件）FAR:failure aualysis report故障分析报告CAR:Corrective action report改善报告BPR：企业流程再造(Business Process Reengineering)ISAR ：首批样品认可(Initial Sample Approval Request)-JIT：实时管理(Just In Time)QCC ：品管圈(Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面品质环境管理)PD: Production Department (制造)LOG: Logistics (后勤支持)Shipping: (进出口)AOQ：Average Output Quality平均出货质量AOQL：Average Output Quality Level平均出货质量水平FMEA：failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA：Customer Simulate Analysis客户模拟分析SQMS：Supplier Quality Management System供应商品质管理系统QIT: Quality Improvement Team 品质改善小组QIP：Quality Improvement Plan品质改善计划CIP：Continual Improvement Plan持续改善计划SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D单)小组成立问题说明实施并验证临时措施确定并验证根本原因选择并验证永久纠正措施实施永久纠正措施预防再发生小组祝贺PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知)QAPS: Quality Assurance Process Sheet (品质工程表)DRP ：运销资源计划(Distribution Resource Planning)DSS：决策支持系统(Decision Support System)EC ? ：电子商务(Electronic Commerce)EDI ：电子资料交换(Electronic Data Interchange)EIS ：主管决策系统(Excutive Information System)ＥＲＰ：企业资源规划(Enterprise Resource Planning)FMS ：弹性制造系统(Flexible Manufacture System)KM ? ：知识管理(Knowledge Management)4L ：逐批订购法(Lot-for-Lot)LTC ：最小总成本法(Least Total Cost)LUC ：最小单位成本(Least Unit Cost)MES ：制造执行系统(Manufacturing Execution System) MPS ：主生产排程(Master Production Schedule)MRP ：物料需求规划(Material Requirement Planning) MRPⅡ：制造资源计划(Manufacturing Resource Planning) OEM ：委托代工(Original Equipment Manufacture)ODM ：委托设计与制造(Original Design & Manufacture) OLAP：线上分析处理(On-Line Analytical Processing) OLTP：线上交易处理(On-Line Transaction Processing) OPT ：最佳生产技术(Optimized Production Technology) PDCA：PDCA管理循环(Plan-Do-Check-Action)PDM：产品数据管理系统(Product Data Management)) RCCP：粗略产能规划(Rough Cut Capacity Planning) SCM ：供应链管理(Supply Chain Management)SFC ：现场控制(Shop Floor Control)TOC：限制理论(Theory of Constraints)TQC ：全面品质管制(Total Quality Control)FYI/R:for your information/reference仅供参考ASAP:尽快S/T:Standard time标准时间TPM:total production maintenance：全面生产保养ESD Wrist strap：静电环IT:information technology信息技术，资讯科学CEO：Chief Executive Officer执行总裁COO：Chief Operaring Officer首席业务总裁SWOT：Strength,Weakness,Opportunity,Threat优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通Cooperation：统御融合Vibration Testing：振动测试IDP：Individual Development Plan个人发展计划MRP：Material Requirement Planning物料需求计划MAT'S：Material材料LRR：Lot Rejeet Rate批退率ATIN：Attention知会3C：Computer ,Communication , Consumer electronic消费性电子5W1H：When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement人,机器,材料,方法,测量4MIE: Man,Material,Machine,Method,Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money , Information 人力，机器，材料，方法, 市场，管理，资金，资讯1 Accuracy 准确度2 Action 行动3 Activity 活动4 Analysis Covariance 协方差分析5 Analysis of Variance 方差分析6 Approved 承认7 Attribute 计数值8 Average 平均数9 Balance sheet 资产负债对照表10 Binomial 二项分配11 Brainstorming Techniques 脑力风暴法12 Cause and Effect Matrix 因果图(鱼骨图)13 CL:Center Line 中心线14 Check Sheets 检查表15 Complaint 投诉16 Conformity 合格（符合）17 Control 控制18 Control chart 控制(管制)图19 Correction 纠正20 Correlation Methods 相关分析法21 CPI: continuouse Process Improvement 连续工序改善22 Cross Tabulation Tables 交叉表23 CS: Customer Sevice 客（户）服（务）中心24 DSA: Defects Analysis System 缺陷分析系统25 Data 数据? ? ? Description:品名26 DCC: Document Control Center 文控中心27 Decision 决策、判定28 Defects per unit 单位缺点数29 Description 描述30 Device 装置31 Do 执行32 DOE: Design of Experiments 实验设计33 Element 元素34 Engineering recbnology 工程技35 Environmental 环境36 Equipment 设备37 Estimated accumulative frequency 计算估计累计数38 E Equipment Variation 设备变异39 External Failure 外部失效,外部缺陷40 FA: Failure Analysis 失效分析41 Fact control 事实管理42 Fatigue 疲劳43 FMEA: Failure Mode and Effect Analysis失效模式与效果分析44 FP First-Pass Yield （第一次通过）合格率45 FQA: Final Quality Assurance 最终品质保证46 FQC: Final Quality control 最终品质控制47 Gauge system 测量系统48 Grade 等级49 Histogram 直方图50 Improvement 改善51 Initial review 先期审查52 Inspection 检验53 Internal Failure 内部失效、内部缺陷54 IPQC: In Process Quality Control 制程品质控制55 IQC: Incomming Quality Control 来料品质控制56 IS International Organization for Standardization 国际标准化组织57 LCL: Lower Control limit 管制下限58 LQC: Line Quality Control 生产线品质控制59 LSL: Lower Size Limit 规格下限60 Machine 机械61 Manage 管理62 Materials 物料63 Measurement 测量64 Median 中位数65 MSA: Measurement System Analysis 测量系统分析66 Occurrence 发生率67 Operation Instruction 作业指导书68 Organization 组织69 Parto 柏拉图70 PPM arts per Million （百万分之）不良率71 Plan 计划72 Policy 方针73 Population 群体74 PQA: Process Quality Assurance 制程品质保证75 Practice 实务(践)76 Prevention 预防77 Probability 机率78 Probability density function 机率密度函数79 Procedure 流程80 Process 过程81 Process capability analysis 制程能力分析（图）82 Process control and Process capability制程管制与制程能力83 Product 产品84 Production 生产85 Projects 项目86 QA: Quality Assurance 品质保证87 QC: Quality Control 品质控制88 QE: Quality Engineering 品质工程89 QFD: Quality Function Desgin 品质机能展开(法)90 Quality 质量91 Quality manual 品质手册92 Quality policy 品质政策(质量方针)93 Random experiment 随机试验94 Random numbers 随机数95 R:Range 全距（极差）96 Reject 拒收97 Repair 返修98 Repeatusility 再现性99 Reproducibility 再生性100 Requirement 要求101 Responsibilities 职责102 Review 评审103 Reword 返工104 Rolled yield 直通率105 RPN: Risk Priority Number 风险系数106 Sample 抽样,样本107 Sample space 样本空间108 Sampling with replacement 放回抽样109 Sampling without replacement 不放回抽样110 Scatter diagram 散布图分析111 Scrap 报废112 Simple random sampling 简单随机取样113 Size 规格114 SL: Size Line 规格中心线115 Stratified random sampling 分层随机抽样116 SOP: Standard Operation Procedure 标准作业书117 SPC: Statistical Process Control 统计制程管制118 Specification 规范119 SQA: Source(Supplier) Quality Assurance 供货商品质保证120 Stage sampling 分段随机抽样121 Standard Deviation 标准差122 Sum of squares 平方和123 Taguchi-method 田口(试验)方法124 Theory 原理125 TQC: Total Quality Control 全面品质控制126 TQM: Total Quality Management 全面品质管理127 Traceablity 追溯128 Training 培训129 UCL: Upper Control Limit 管制（控制）上限130 USL: Upper Size Limit 规格上限131 Validation 确认132 Variable 计量值133 Verification 验证134 Version 版本135 VOC: Voice of Customer 客户需求136 VOE: Voice of Engineer 工程需求137 Inventory stock report:库存清单报告138 Sales order report:出货报告质量人员名称类QC ? quality control ? 品质管理人员FQC ? final quality control ? 终点质量管理人员IPQC ? in process quality control ? 制程中的质量管理人员OQC ? output quality control ? 最终出货质量管理人员IQC ? incoming quality control ? 进料质量管理人员TQC ? total quality control ? 全面质量管理POC ? passage quality control ? 段检人员QA ? quality assurance ? 质量保证人员OQA ? output quality assurance ? 出货质量保证人员QE ? quality engineering ? 质量工程人员质量保证类FAI ? first article inspection ? 新品首件检查FAA ? first article assurance ? 首件确认CP ? capability index ? 能力指数CPK ? capability process index ? 模具制程能力参数SSQA ? standardized supplier quality audit ? 合格供货商质量评估FMEA ? failure model effectiveness analysis ? 失效模式分析FQC运作类AQL ? Acceptable Quality Level ? 运作类允收质量水平S/S ? Sample size ? 抽样检验样本大小ACC ? Accept ? 允收REE ? Reject ? 拒收CR ? Critical ? 极严重的MAJ ? Major ? 主要的MIN ? Minor ? 轻微的Q/R/S ? Quality/Reliability/Service ? 质量/可靠度/服务P/N ? Part Number ? 料号L/N ? Lot Number ? 批号AOD ? Accept On Deviation ? 特采UAI ? Use As It ? 特采FPIR ? First Piece Inspection Report ? ? 首件检查报告PPM ? Percent Per Million ? 百万分之一制程统计品管专类SPC ? Statistical Process Control ? 统计制程管制SQC ? Statistical Quality Control ? 统计质量管理GRR ? Gauge Reproductiveness & Repeatability ? 量具之再制性及重测性判断量可靠与否DIM ? Dimension ? 尺寸DIA ? Diameter ? 直径N ? Number ? 样品数其它质量术语类QIT ? Quality Improvement Team ? 质量改善小组ZD ? Zero Defect ? 零缺点QI ? Quality Improvement ? 质量改善QP ? Quality Policy ? 目标方针TQM ? Total Quality Management ? 全面质量管理RMA ? Return Material Audit ? 退料认可7QCTools ? 7 Quality Control Tools ? 品管七大手法通用之件类ECN ? Engineering Change Notice ? 工程变更通知(供货商)ECO ? Engineering Change Order ? 工程改动要求(客户)PCN ? Process Change Notice ? 工序改动通知PMP ? Product Management Plan ? 生产管制计划SIP ? Standard Inspection Procedure ? 制程检验标准程序SOP ? Standard Operation Procedure ? 制造作业规范IS ? Inspection Specification ? 成品检验规范BOM ? Bill Of Material ? 物料清单PS ? Package Specification ? 包装规范SPEC ? Specification ? 规格DWG ? Drawing ? 图面系统文件类ES ? Engineering Standard ? 工程标准CGOO ? China General ? PCE龙华厂文件IWS ? International Workman Standard ? 工艺标准ISO ? International Standard Organization ? 国际标准化组织GS ? General Specification ? 一般规格部类PMC ? Production & Material Control ? 生产和物料控制PCC ? ? Product control center ? ? ? 生产管制中心PPC ? Production Plan Control ? 生产计划控制MC ? Material Control ? 物料控制DC ? Document Center ? 资料中心QE ? Quality Engineering ? 质量工程(部)QA ? Quality Assurance ? 质量保证(处)QC ? Quality Control ? 质量管理(课)PD ? Product Department ? 生产部LAB ? Laboratory ? 实验室IE ? Industrial Engineering ? 工业工程R&D ? Research & Design ? 设计开发部生产类PCs ? Pieces ? 个(根,块等)PRS ? Pairs ? 双(对等)CTN ? Carton ? 卡通箱PAL ? Pallet/skid ? 栈板PO ? Purchasing Order ? 采购订单MO ? Manufacture Order ? 生产单D/C ? Date Code ? 生产日期码ID/C ? Identification Code ? (供货商)识别码SWR ? Special Work Request ? 特殊工作需求L/N ? Lot Number ? 批号P/N ? Part Number ? 料号OEM ? Original Equipment Manufacture ? 原设备制造PC ? Personal Computer ? 个人计算机CPU ? Central Processing Unit ? 中央处理器E-MAIL ? Electrical-Mail ? 电子邮件N/A ? Not Applicable ? 不适用QTY ? Quantity ? 数量I/O ? input/output ? 输入/输出NG ? Not Good ? 不行,不合格C=0 ? Critical=0 ? 极严重不允许APP ? Approve ? 核准,认可,承认CHK ? Check ? 确认ASS'Y ? Assembly ? 装配,组装T/P ? True Position ? 真位度5WIH ? When, Where, Who, What, Why, How to6M ? Man, Machine, Material, Method, Measurement, Message4MTH ? Man, Material, Money, Method, Time, How ? 人力,物力,财务,技术,时间(资源) SQA ? Strategy Quality Assurance ? 策略质量保证DQA ? Design Quality Assurance ? 设计质量保证MQA ? Manufacture Quality Assurance ? 制造质量保证SSQA ? Sales and service Quality Assurance ? 销售及服务质量保证LRR ? Lot Reject Rate ? 批退率SPS ? Switching power supply ? 电源箱DT ? Desk Top ? 卧式(机箱)MT ? Mini-Tower ? 立式(机箱)DVD ? Digital Video DiskVCD ? Video Compact DiskLCD ? Liquid Crystal DisplayCAD ? Computer Aided DesignCAM ? Computer Aided ManufacturingCAE ? Computer Aided EngineeringPCB ? Printed Circuit Board ? 印刷电路板CAR ? Correction Action Report ? 改善报告NG ? Not Good ? 不良WDR ? Weekly Delivery Requirement ? 周出货要求PPM ? Percent Per Million ? 百万分之一TPM ? Total Production Maintenance ? 全面生产保养MRP ? Material Requirement Planning ? 物料需计划OS ? Operation System ? 操作系统TBA ? To Be Assured ? 待定,定缺D/C ? Drawing ChangeP/P ? Plans & ProcedureEMI ? Electrical-Music Industry ? 电子音乐工业? Electrical Magnetic Interference ? ? 电子干扰RFI ? Read Frequency Input ? 读频输入MMC ? Maximum Material ConditionMMS ? Maximum Material SizeLMC ? Least Material ConditionLMS ? Least Material SizeLED ? lighting-emitting diode 发光二极管QBR ? Quarter Business RecordCIP ? Continuous improvement process ? ?FGI ? Forecasted Goal InventoryCNC ? Computerized numeral controllerB2C ? Business to customerB2B ? Business to businessAVL ? Approved vendor listPOP ? Procedure of packagingEOL ? End of lifeVDCS ? Vender defect correcting sheetPDCS ? Process defect correcting sheetGRN ? Goods receiving noteA/R ? Accounting receivableA/P ? Accounting payable专业词汇通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位Human Resources Department人力资源部Head count 人头数production department生产部门planning department企划部QC Section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management ? 颜色管理? ? ?Visual management 目视管理?production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范? ?computer case 计算机外壳(组件)personal computer enclosure 计算机机箱产品? ?front plate前板rear plate后板chassis |'∫?si| 基座bezel panel面板Hood ? 上盖base pan 基座? ? ? ? ?bezel ? 面板?riser card 扩充卡?flat cable 排线? ? ? ? ? ?TOP driver cage ? 上磁架? ?bottom driver cage ? 下磁架? ? ?resin film ? 树脂膜? ? ?raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑料件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程窗体production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck ? 瓶颈模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模stage die工程模compound die复合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 换模to fix a die装模to repair a die修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)upper supporting blank上承板upper padding plate blank上垫板top plate上托板（顶板）top block上垫脚stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块die locker锁模器pressure plate =plate pinch压板thickness gauge厚薄规cutting die, blanking die冲裁模die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条panel board镶块to load a die装上模具to unload a die 御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块pilot导正筒trim剪外边pierce剪内边pocket for the punch head挂钩槽slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch =die button圆冲子shape punch =die insert异形子stock located block定位块metal plate钣金miller铣床grinder磨床tolerance公差score =groove压线sliding block滑块lathe车active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板capability能力parameter参数factor系数driller钻床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves =spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold挤压式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue, cont.连动to grip(material)吸料location lump, locating piece, location block定位块reset复位to file burr 锉毛刺embedded lump |in'bed| mp|镶块 |lstamping-missing漏冲to tight a bolt拧紧螺栓to loosen a bolt拧松螺栓punched hole冲孔to cut edge =side cut =side scrap 切边to bending折弯to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake铆合designing, to design设计design modification ? 设计修改成gauge(or jig)治具pedal踩踏板stopper阻挡器flow board流水板torque扭矩spline =the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的forming成型(抽凸,冲凸)draw hole抽孔bending折弯emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线stamp letter冲字(料号)tick-mark nearside正面压印tick-mark farside反面压印冲压类punch, press冲punching machine 冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management制造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包成型类well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口runner less无浇道sprue less ? 无射料管方式long nozzle延长喷嘴方式spur浇口;溶?waste废料board广告牌sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理组装类Assembly line组装线Layout布置图Conveyer流水线运输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine/heat stake热熔机processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机烤漆类phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉organic solvent有机溶剂demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料volatile挥发性。