模具专业术语大全
常用模具术语
常用模具术语出模：啤件在顶出机构的作用下离开模具的过程啤把：出模角度或者出模斜度倒扣：因为侧面角度或凹位而无法垂直出模的位置排模：模具的排期正哥：型腔在上模，型芯在下模的一种模具结构反哥：型心在上模，型腔在下模的一种模具结构分型：把产品分为上下模的过程种针：基准针，配针时以此针为基准放样：胶样的比例放大复样：胶样的复制调面：在雕刻时，调整胶样表面与要加工表面平行的过程摆斜雕刻：在雕刻时，因有些面不易加工，把胶样摆成一定角度的加工方法顶针出柱：用顶针的顶面来封住成型柱的底面，而使柱成型顶针包针：顶针过长或配针不当，而使顶针包在产品内锅柱：柱的前端有一锥型孔，上大下小，起到铆钉的作用。
多用于压铸模镶针出柱：用镶针的顶面来封住成型柱的底面，而使柱成型镶针出孔：用镶针成型孔原身出：用内模加工出要成型的形状来成型的方法大水口：二板模入水水塘：啤件为透明件或要求变形较小的薄壁件入水时，采用在浇口与流道间所加的一段起到缓冲作用的位置方法，这个缓冲位置就是入水水塘磨角尺：用磨床磨直角锣正：用铣床铣平面或直角Fit平面：用打磨机把平面精加工到要求的配合公差范围Fit枕位：用打磨机把枕位精加工到要求的配合公差范围Fit行位：用打磨机把行位精加工到要求的配合公差范围Fit插穿：用打磨机把插穿位精加工到要求的配合公差范围面镶：镶件从内模的上表面镶入一定的深度，不可到底面，下面用螺丝固定通镶：镶件从内模的下面镶入，直达上表面，通过整个内模兜底镶：镶件从内模的下面镶入，直达上表面，通过整个内模，在镶件下面以台阶形式固定侧镶：镶件从侧面镶入，一般多用在行位上奔子孔：胶样上的一个基准孔，所有的位置都要从这个孔取数镗蚀：铜公水平运动加工照数：用中心镜对要加工部位进行坐标值确定打盲孔：用电火花加工盲孔损公：损耗的铜公积碳：EDM加工时产生的碳堆积在零件或铜公上，使被加工的零件的平面凹凸不平粗公：粗加工时使用的铜公，火花间隙一般为单边0.25幼公：精加工时使用的铜公，火花间隙一般为单边0.07暴公：比粗公火花间隙还要大的铜公，用与粗加工立体公：一个整体铜公，形状与整个上模或这个下模相同清角铜公：对有些直角部位，因CNC不能完全加工而留有余量。
模具专业术语
Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力non-return valve 止回阀shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure / packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比mold close time 合模时间Resin 胶料/.Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重Elongation 延伸率density 密度melting point 熔点Polystyrene 聚苯乙烯（PS）.m,k.bn 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethylene 聚乙烯glass fiber 玻纤Condensation 凝固，浓缩crystalline resin 结晶形塑料Mold materials 模具General-purpose steel 多用途钢tool steel 模具钢Free-cutting steel 高速切削钢case hardening steel 表面硬化钢Pre-hardened steel 预硬钢ball and roller bearing steel 滚珠轴承钢Nonferrous steel 非铁合金high speed steel 高速钢cast iron 铸铁Steel specification 钢材规格steel certification 钢材合格证明书Stainless steel 不锈钢nickel 镍chrome 铬aluminum 铝Copper 铜brass 黄铜bronze 青铜titanium 钛Processing 钢材的加工方法Harding / quench 淬火nitride 氮化temper 回火anneal 退火Roll 轧制abrasive 研磨，磨损的finish 精加工，抛光（polish）Case-hardening 表面硬化milling machine 铣（锣）床Lathe车床drill 钻床wire cut 线割NC(numerical control ) 数控材料EDM (Electrical discharge machine) 电火花加工Cut steel 开料Precision ground 精密研磨heat treatment 热处理tap 丝锥，攻牙Texture 蚀纹weld 焊接forge 锻压deformation 变形Spraying 喷涂die-cast 压铸Properties 性能Resistance 电阻，抵抗能力abrasion / wear磨损erode / corrode 腐蚀Toughness 韧性yield strength 屈服强度tensile strength 拉伸强度Fatigue strength 疲劳强度break 断裂stress 应力hardness 硬度Humidity / moisture 潮湿，湿气roughness 粗糙度parameter 参数Thermal conductivity 导热系数manufacture 制造，加工drawback 缺点Ductility 延展性grain 晶粒property 性能，财产brittleness 脆性GD&T （Geometric Dimensions and Tolerance ）形位尺寸公差Flexural strength 挠曲强度impact 冲击conductivity 传导性，导电性Optical 光学的transparent 透明的insulation 绝缘Mechanical 机械的processability 可加工性能timeyield 蠕变Physical 物理的flow rate 流动速率compressive strength 压缩强度Adhesive 粘附的，胶合durability 耐用性Mold design 模具设计Tooling specification 模具规格mould flow 流动模拟sprue nozzle 唧咀孔Clearance 避空，间隙undercut 倒扣flush 插入，埋入legend 图例Groove 凹槽latch 插销class 类型，种类plan 平面图Orifice 孔，口column 柱位boss 凸台standard 标准，规格Rib 骨位tapered interlock 锥形管位块Bubbler 炮隆Bolt 螺钉，销顶identification mark 铭牌P/L strip 锁模片Overflow well / cold-slug well 冷料井V ent 排气pocket 槽Gate location 入水点full line 实线broken line 虚线Retainer 固定，支撑operator 操作者（啤工）receptacle 插座Lifting hole 吊令孔insulation plate 隔热板cavity number 型腔号Bolster 支撑，垫子vent channel 排气槽leak / filter 渗漏Leak test 试运水stamp / engrave 雕刻，印记（打字唛）Clamp slot 码模槽support button / pin 垃圾钉cut steel 开料Lodge 安装，放置inlay 镶嵌，插入cam / lifter 斜顶Stripper推方lifting bar 吊模方sprue 唧咀tolerance 公差Counter bore 沉孔slant 倾斜，斜面conical 圆锥的，圆锥形的Bolt 螺栓manifold 热流道板prototype tooling 原型试验Gusset 角撑reverse mold 倒装模constrain / restrict约束，限制Counter lock 反锁thermocouple 热电偶moldmaker 模具制造商Asset / property number 资产编号tool product destination 模具生产地点Accelerating ejection 加速顶出hydraulic 液压的pneumatic 气动的Trapezoid 梯形的semi-round 半圆形format 格式baffle 隔水片Electrode 电极，铜公spare part 配件gall 磨伤，插伤Cable 电缆，电线plating / coating （电）镀bonding / joint 接头Wall transition 壁厚过渡Product problem 产品问题Troubleshoot 故障处理reduce(add) plastic 减（加）胶Burr/flash披峰Burn mark 烧焦ejector mark 顶针印，顶白black specs 黑点，黑斑Discoloration 混色，污点gloss 光泽jetting/worming 走水纹Sink mark 缩水void / bubble 气泡，夹气distortion 变形Warpage 翘曲short molding / non-fill缺胶，未走齐Weld line / knit line 夹水线discarded as useless 报废Split line 夹线stick in sprue bushing / cavity / core 粘唧咀/前模/后模Break / crack 顶裂brittleness 脆性，易脆Others 其他Invoice 发票，清单vendor(er) 卖方vendee 买方guideline 方针，指导Intricate 复杂的confidential 机密的，不可外泄的proprietary 私有的Authorize 批准，授权recipient 接收者issue ①发布，提供；②问题Approve 确认，赞成requirement 需要，必需物const 常数，常量Regarding 关于，涉及opposite 相反的，对面的latitude 纬度，纵向的V ersion 版本definition 注释，解说transversal 横向的，截线Profile 轮廓，剖面eliminate / cancel 取消allow / permit 允许，许可Respective 各自的，分别的individual 单独的decrease 减少increase 增加Preliminary 初步的approximately 大约，近似estimate / valuate估计，预算Adjust 调整，校准application 应用，申请maintain 维持Accurate / precise 精确的smooth 光滑，顺畅的device 装置，设备Convenient 方便的deadline 截至日期available 有用的，有空的Shift 轮班，换班critical 关键的，临界的exceptional 异常的，优异的Exceed 超过layout 布局，方案loss 损失，消耗install 安装，安置Rotation 旋转item 条款，项目quotation 报价stabilize 稳定Quality 质量quantity 数量couple 连接，接合configuration 构造，外形Illustrate 图解说明simulation 模拟，仿真recommend 推荐使用。
模具行业常用术语及解释
模具行业常用术语1、什么叫PL面？PL面又称:分型面、啪拉面,就是指模具在闭合时前模与后模相接触的部分。
2、什么就是碰穿,什么就是插穿？与PL面平行的公母模贴合面叫碰穿面,与PL面不平行的公母模贴合面叫插面。
3、条与丝的关系？条与丝都就是长度单位,条为台湾用语,1条=0、01mm,丝为香港用语,1丝=0、01mm,所以1条=1丝。
4、枕位就是什么？外壳类塑件的边缘常开有缺口,用于安装各类配件,此处形成的枕壮分型部分称为枕位。
5、火山口就是什么？BOOS柱根部减胶部分反映在模具上的类型于火山爆发后的形状叫做模具火山口。
6、呵指就是什么？呵指的就是模仁,香港习惯用语。
7、什么就是老虎口？老虎口又称为:管位,即用来限位的部分。
8、什么叫排位？模具上的产品布局称为排位。
9、什么叫胶位？模具上的产品的空穴称为:胶位。
10、什么叫骨位？产品上的筋称为:骨位。
11、什么叫柱位？产品上的BOSS的柱称为:柱位。
12、什么叫虚位？模具上的间隙称为:虚位。
13、什么叫扣位？产品上连接用的钩称为:扣位。
14、什么叫火花纹？电火花加工后留下的纹称为火花纹。
15、铜工就是什么？电火花通常采用易于加工的铜料做放电电极,称为铜工,也称电极,铜工一般分为:粗工、粗幼工、幼工、幼工又称精工。
16、火花位通常就是多少？放电过程中,铜工与钢料之间的放电间隙称为火花位,粗工火花一般在15到50条,幼工火花位一般在5到15条。
17、料位就是什么？塑胶产品的避厚,也称肉厚。
18、原身留就是什么？原身留就是相对与割镶件而言,原身留就是指一整块钢材为加工胚料,加工的时候一起加工出来。
19、熔接痕就是什么？两股塑胶相遇所形成的线称为熔接痕。
20、喷流就是什么?塑胶从进胶口进入型腔后形成弯曲折叠似蛇的流痕称为喷流。
21、DME就是指什么,HASCO就是指什么？标准件的标准,DME就是美制的,HASCO就是欧制的。
22、什么叫倒扣？产品中前后模无法直接脱模的部分成为倒扣。
50个模具专业术语
50个模具专业术语1. 模具 (Mold)2. 塑料模具 (Plastic Mold)3. 金属模具 (Metal Mold)4. 注塑机 (Injection Molding Machine)5. 压铸机 (Die Casting Machine)6. 打磨 (Polishing)7. 铣削 (Milling)8. 钳工 (Machining)9. 精雕 (Engraving)10. 焊接 (Welding)11. 冲压 (Stamping)12. 切割 (Cutting)13. 合模 (Closing)14. 分模 (Opening)15. 导柱 (Guide Pillar)16. 导套 (Guide Bush)17. 滑块 (Slider)18. 塑料件 (Plastic Part)19. 金属件 (Metal Part)20. 模仁 (Core)21. 模腔 (Cavity)22. 底座 (Base)23. 热流道 (Hot Runner)24. 冷却系统 (Cooling System)25. 泵箱 (Pump Box)26. 压缩机 (Compressor)27. 水力缸 (Hydraulic Cylinder)28. 模具钢 (Mold Steel)29. 法兰 (Flange)30. 注塑模具 (Injection Mold)31. 放电加工 (Electrical Discharge Machining)32. 模仁巧妙 (Core Pull)33. 螺旋通道 (Spiral Channel)34. 冷却塔 (Cooling Tower)35. 酸洗 (Acid Etching)36. 布胶 (Rubberizing)37. 文字标记 (Texturing)38. 研磨剂 (Polishing Compound)39. 硅胶 (Silicone)40. 硬度测试 (Hardness Testing)41. 射出速度 (Injection Speed)42. 模具寿命 (Mold Life)43. 热流道系统 (Hot Runner System)44. 冷却时间 (Cooling Time)45. 模具设计 (Mold Design)46. 模具制造 (Mold Manufacturing)47. 模具修理 (Mold Repair)48. 模具改造 (Mold Modification)49. 模具试模 (Mold Trial)50. 模具测试 (Mold Testing)。
模具专业术语
模具专业术语模具专业术语Company Document number：WUUT-WUUY-WBBGB-BWYTT-1982GT模具专业术语——注塑模(锦浩塑胶模具厂）English Training——Injection Mold（一）模具专业基本用词Professional Terms1．塑料—plastic, resin2．样件—sample3．钢料—steel4．注塑机—injection machine, press5．产品—part, product, moulding6．模具—mold, mould, toolA 简易模（样板模）—prototype moldB 量产用模具—production mold 7．三维造型（数模）—model, 3D data8．二维产品图—2D part drawing9．设计—design10．制造—manufacture, build up, construction11．检验—chec k, inspection12．测量—measure, inspection13．修改—change, modify, correction14．工程更改—engineer change15．质量—quality16．数量—quantity17．基准—datum, reference（二）如何解析2D 产品图How to read 2D part drawing一．产品几何Geometry1．点—point2．线（边）—line, edge3．面faceA 侧面—sideB 表面—surfaceC 外观面—appearance surface 4．壁厚—wall thickness, stock thickness5．加强筋（骨位）—rib6．孔—hole7．细长的槽—slot8．柱位—boss9．角—cornerA 圆角—filletB 倒角—chamferC 尖角—sharpcorner10．斜度—angle, taper11. 凹槽—recess ,groove二．分模信息Splitting1．分型线—parting line (P/L), splitting line2．主分模方向—main direction, line of draw3．浇口设定—gating三．产品标识Part Identification1．产品名称—part name (P/N)2．产品编号+版本号—part number + revision (Rev.)3．型腔号—cavity number4．材料标记—material symbol5．模具编号—mold number (no.)6．日期印—dating insert, date code7．循环印—cycling code8．公司标志—company logo四．技术要求Specification (Special Requirement)1．项目启动表Kick-off sheet1）项目名称—program name, project name2）产品名称—part name, product name, part description3）产品编号—part number (P/N)4）客户模号—customer mold no.5）项目启动日期— kick off date,start date6）项目完成日期— due date, lead time7）内模件用钢— tool steel8）型腔数量—number of cavit ies9）数模文件编号—data file n o.10）注塑材料—resin,plastic, raw material11）收缩率—shrink, shrinkage, shrink factor12）注塑机吨位—molding machine size, injection machine size 13）成型周期—cycle time14）型腔光洁度—cavity polish15）型芯光洁度—core polish16）皮纹（晒纹）—texture, grain17）拔模斜度—draft angle, removal taper18）注塑件颜色及光泽—molded color & gloss19）模具加工地— manufacturing facility20）热流道供应商—manifold manufacturer, manifold supplier 21）浇口位置—gate location / position22）浇口类型—gate type23）产品标识—stamp information, part identification24）特殊要求— special instructions2．产品质量及外观要求Part Quality & Appearance1）尺寸及公差Dimension & Tolerance①重要尺寸—critical dimension, important dim., key dim.②理论尺寸—nominal dimension③实际尺寸—actual dimension④公差—tolerance⑤公差带—tolerance range⑥尺寸超差—dimension deviation⑦接受（合格）—accept, OK⑧拒绝（不合格）—reject, refuse, obsolete, NG⑨让步接受—concession, special admit⑩返工—re-work2）产品缺陷（较常见）Defects (normal)①缩印—sink mark, shrinkage②飞边—flash, burr③段差—mismatch discrepancy④银丝纹—snake marks, streak⑤弯曲—warpage, distortion⑥打不足（缺料）—short shot⑦熔接线—weld line3．产品外观Part Appearance①产品颜色—part color②产品光泽—gloss③皮纹粒度—grain4．常用词汇、词组及短语Normal Word, Short Sentence1）单边—per side2）双边—both sides3）加入，添加—add, incorporate4）去除，取消—remove, cancel5）满足…的要求，符合，与…要求一致—according to, conform to, satisfy, meet 6）要求，需要—require, need, demand 7）确认—be approved, agreed by …8）允许—permit, allow9）在…范围之内—within10）不可以，不允许，禁止—free from,prevent, avoid11）…，除非有另指—…unless otherwise spe cified12）…或少于—…or less13）自动化运作—automatic operation14）未注尺寸（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.15）分型线上的飞边（披缝）或段差应小于…Bu rrs and discrepancy on the P/L shall be … or less.五．标题栏Title Block1．产品名称—part name2．图纸编号 + 版本号（索引号）—drawing no. + level (index) 3．一般公差[的标准] —general tolerance（三）如何阅读制模标准How to read tooling standard一．模具结构术语Mold Construction TerminologyA．模架Mold Base1．模架量化特征Measurement Feature①长X 宽X 高—Length X Width X Height②模具推高尺寸（模厚）—stack height of mould③模具重量—total weight of mould, mould thickness2．定模底板—front plate, top clamping plate, clamp plate, clamping plate 3．定模板—cavity plate, fixed mould plate, A –plate4．动模板—core plate, moving mould plate, B – plate5．支撑板—support plate, backing plate6．模脚—support blocks, rails, risers, spacer block7．顶杆固定板—retaining plate, ejector retaining plate8．顶板—ejector plate9．动模底板—back plate10．导柱—guide pillar, leader pin, guide pin11．导套—guide bush, leader pin bush12．复位杆—return pin, push-back pin13．弹簧—spring14．撑头—support pillar15．推板导柱、导套—ejection guide pin / bush16．挡钉—stop pin, stop button17．站立脚—standing-off pillars18．标牌—plaque scutcheonB．成型零部件moulding components19．型芯—core20．型腔—cavity21．镶针—core pin22．镶块—insert, split23．滑块—slide, sliding split24．斜顶—lifter, angled-lift splitA 斜顶头—lifter headB 斜顶杆—lifter rod, lifter shaft 25．成型顶杆—moulding face pin, form pinC．浇注系统Feed System1．塑料Mouldinga．主流道—sprueb．分流道runner①主分流道—main runner ②二级分流道— branch runner分流道断面形状cross-sectional shape of runner①圆形—full round②半圆形—semicircular③梯形—trapezoidalc．浇口gate常用浇口形式normal gate type :①边缘浇口（J型浇口）—edge gate, J – gate②侧浇口—side gate③潜伏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate④潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口(主流道型浇口) —sprue gate, direct gate⑦护耳式浇口—tab gated．模腔—impressione．冷料井—cold slug wellf．热流道—hot runner2．模具零件mold componentsa．定位圈—locating ring, location ring, register ringb．浇口套—sprue bushc．挡圈—stop ringd．浇口镶块—gate inserte．热流道板—manifoldf．热嘴—hot dropD．分型面及其锁紧、排气Parting Surface, inter-locking & venting1．分型线—parting line ( P/L )2．镶拼线—bodyline, joint line3．平/ 不平的分型面—flat / non – flat parting surface4．封胶面—shut off surfaces, seal-off surfaces5．擦位—shut off6．碰穿位—kiss-off7．管位—parting line lock8．分型面的释放(避空) —relief of parting surface9．分型面的平衡—balancing of parting surface10．锁紧角度—locking angle11．锁紧力—clamping force12．锁模板—safety strap13．精定位—Interlock, die lock14．困气—air trap15．排气槽—vent, vent slotE．滑块机构Slide1．驱动Actuation①斜导柱—angled pin, horn pin, cam pin②弹簧—spring③油缸—hydraulic cylinder2．制动Detention①滑块固定器— slide retainer②弹簧制动器— spring-loaded detention (plunger)③挡钉、挡板— stop pin, stop plate, slide stop3．导轨—gib, guide strip4．锁紧块（楔紧块）—heel block, locking heel, wedge block, chase block 5．耐磨片—wear plate, wear strip6．压板—retainer7．螺钉—screw8．定位销—dowelF．斜顶机构Lifter1．斜顶头—lifter head2．斜顶杆—lifter rod, lifter shaft3．开口销—split pin4．固定板（压板）— retainer plate5．耐磨片—wear plate6．铜导套— bronze bushing7．衬套— spacer8．导轨— L – gib9．滑动块— slideG．顶出系统Ejection System1．基本词汇Basic Word①顶出行程— ejection stroke②模具开档—daylight③粘模—stick④产品脱模—part is push off from, clear part of mould, separation of part 2．顶板机构Ejector plate assembly①顶板（推板）— ejector plate②顶板固定板— retaining plate③推板导柱— ejector guide pin④推板导套— ejector guide bush⑤撑头—support pillar, pillar support3．复位机构Return System①复位杆（回程杆）— return pin, push – back pin②挡钉—stop pin, stop button③压簧—compressed spring④碟簧—a stack of “Belleville” washers⑤早复位机构—early return system⑥强制复位机构—positive return system4．顶出方法 Ejection Techniques1）顶杆顶出—pin ejection2）顶管顶出— sleeve ejection3）顶块顶出— bar ejection4）扁顶顶出— blade ejection5）顶板顶出— stripper ejection6）油缸顶出— hydraulic ejection7）气顶— air ejection8）阀门顶出—valve ejection5．顶出元件Ejection Elements1）拉料杆—sprue puller, sucker pin2）顶杆—ejector pin3）阶梯式顶杆— stepped ejector pin4）顶管— ejection sleeve,sleeve5）扁顶— ejector blade, slabbed off ejector pin6）顶块—stripper bar7）顶环—stripper ring8）推板—stripper plate9）加速顶— accelerated ejection6．顶出辅助机构Supplementary operating system1）弹簧柱塞器—spring – loaded plunger2）弹珠定位器— ball catch system3）插销式锁扣— Latch – lock4）尼龙拉杆装置— friction puller device7．电器元件Electric Components1）压力传感器—pressure transducer2）限位开关—limit switchF．冷却系统Cooling System1．基本词汇Basic Word1）温差—temperature variation2）水孔（水道）—waterlines, water-ways, flow-way, channel 3）水路—cooling circuit4）水路示意图—water schematic, schematic circuit5）冷却液—coolant, coolant fluid6）内连接—interconnect7）外连接—external connection8）出口、入口—outlet、inlet9）漏水—water leakage2．水路分布Circuits1）阶梯式水路—stepped system2）喷淋—baffled hole system3）斜孔式水路—angled hole system3．水路元件Components1）闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male2）隔水片—baffle3）密封圈—O – ring4）快插水路接头—quick disconnect fitting, quick connection adaptor5）弯头—elbow6）偶合器（连接器、接头）—adaptor (including a plug & a socket)7）橡皮管—rubber hose8）分水板—water manifoldG．螺纹、螺纹孔& 螺钉Thread, thread hole & screw1．螺纹—thread2．管螺纹—pipe thread3．螺纹孔—screw hole, tapped hole4．起吊孔—handling hole, jack screw hole, eye bolt hole5．螺钉—screw6．内六角螺钉—socket headed cap screw （）7．沉头螺钉—flat headed cap screw （）8．螺栓—bolt, eye bolt9．螺母—nut10．锁紧螺母—locknut11．螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—British Standard Pipe thread （BSP）④美制管螺纹标准—NPT⑤美制粗螺纹标准—United Coarse thread （UNC）⑥美制细螺纹标准—United Fine thread （UNF）H．润滑Lubrication1．润滑槽—grease groove2．加油管—grease line3．油杯—lubrication fittingI．测量仪器Measuring Instrument s1．游标卡尺—vernier caliper2．千分尺—micrometer3．高度规—height gauge4．刻度规—dial gauge5．三坐标测量仪—Coordinate Measure Machine（CMM）6．塞规—pin gauge7．圆角量规—radii gauge8．轮廓投影机—profile projectorJ．注塑机参数Injection Machine Parameter1．注塑机规格参数Injection Machine Specification①锁紧类型clamp typea．油缸—hydraulic b．肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force2．试模工艺参数Moulding Process Parameter, machine setting①时间Timer（TM）, seca．注塑（充填）时间—filling time, injection timeb．冷却时间—cooling timec．补缩时间—packing timed．保压时间—holding timee．成型周期—cycle time②速率、速度Velocity, %、speed, in/seca．注塑（充填）速度—injection speedb．保压速率—hold pressure velocityc．螺杆转速—screw rotation speed③压力Pressure（Prs.）, psia．注塑压力—injection pressureb．保压压力—hold pressurec．回压（背压）—back pressure④温度T emperature（Temp.）, °Fa．注塑机喷嘴温度—nozzle temp.b．料筒前段、中段、后段温度—barrel front、middle、rear temp.c．模温—mould temp.d．料温—purged resin melt temp.e．空射料温—air shot melt temp.。
模具专业术语
模具专业术语————————————————————————————————作者：————————————————————————————————日期:ﻩ模具专业术语——注塑模(锦浩塑胶模具厂)EngｌisｈTraｉninｇ——Iｎjectｉon Mｏld（一）模具专业基本用词Ｐrofesｓional Ｔeｒms１.塑料—ｐlａstic, resin2．样件—ｓample3. 钢料—sｔeeｌ４. 注塑机—injecｔion mａchine, pｒesｓ５．产品—paｒt, prｏdｕct, mouldiｎg６．模具—mold, moｕlｄ, toolＡ简易模（样板模)—prototype mold Ｂ量产用模具—proｄuctio ｎmｏld7. 三维造型(数模）—modeｌ, 3D dａｔa8．二维产品图—2Ｄparｔdrawing９. 设计—ｄesｉｇn10．制造—ｍanufａcture, build ｕp, construction１1．检验—cheｃk, ｉnｓpeｃtｉｏn12.测量—measｕre，inspecｔion13.修改—chａnge, mｏｄify, ｃoｒrection14. 工程更改—ｅnｇineer cｈange１5．质量—qｕality１６. 数量—quantiｔy17. 基准—ｄａｔuｍ, ｒefeｒｅnｃe（二)如何解析2D 产品图？Ｈow tｏread 2D part drａwing？一. 产品几何Geoｍｅtry1．点—poinｔ2.线（边）—line, ｅdge3.面faｃeA 侧面—siｄｅB 表面—ｓurfaceC 外观面—aｐｐeａrａnｃｅsｕrfａｃe4．壁厚—ｗall thｉｃkneｓs, stoｃk thicknesｓ5．加强筋(骨位）—rib6.孔—hole7．细长的槽—sloｔ8．柱位—boss9.角—coｒnerA 圆角—ｆiｌｌｅｔB 倒角—chaｍferＣ尖角—sharp cｏrnｅr10.斜度—anglｅ，taper1１. 凹槽—rｅceｓs ,groove二. 分模信息Spliｔtiｎｇ1．分型线—parｔing line (Ｐ/L), splitｔiｎg lｉne２. 主分模方向—main directｉon, ｌiｎe of draｗ3．浇口设定—ｇatiｎg三. 产品标识Pａrt Iｄeｎtificａtion1. 产品名称—part nａｍe (Ｐ/N)２.产品编号+版本号—paｒt numbｅr ＋revisioｎ（Rｅv.）3. 型腔号—cａvitｙnuｍber4.材料标记—material symbol5. 模具编号—moｌd numbeｒ(no.）6．日期印—ｄatingｉnserｔ, date code7. 循环印—ｃycｌiｎg code8.公司标志—coｍpany loｇo四. 技术要求Sｐecificatioｎ(SpｅciaｌRｅquiｒement)1.项目启动表Kｉcｋ-ofｆshｅｅt１）项目名称—progrａｍname,projｅct naｍe2)产品名称—part namｅ, pｒoduct ｎame, part descriptｉｏn３) 产品编号—ｐart ｎuｍbeｒ(P/N)4) 客户模号—cｕstoｍer mold no.5) 项目启动日期— kick off dａtｅ，starｔdatｅ6)项目完成日期— duｅ dａte, lead tｉｍｅ7) 内模件用钢—ｔool sｔｅｅｌ8）型腔数量—numｂer of cavit iｅs９)数模文件编号—data.10）注塑材料—rｅsin，plastic, raw maｔｅrial1１）收缩率—ｓhrink, ｓhrinkage,sｈrink ｆactoｒ12)注塑机吨位—ｍoldｉng mａchine sｉzｅ， injeｃｔｉon machiｎe size １３）成型周期—cyｃle time14)型腔光洁度—caｖiｔy pｏlish1５) 型芯光洁度—core polｉｓh16）皮纹(晒纹)—tｅxｔurｅ, gｒain17）拔模斜度—dｒaft anｇle, ｒemoval ｔaper18）注塑件颜色及光泽—molｄeｄｃｏｌoｒ& ｇloss19) 模具加工地—manｕfａｃturing ｆaｃility２０）热流道供应商—maniｆｏｌd mａnuｆactureｒ, ｍａｎifolｄ supplieｒ2１)浇口位置—gaｔe ｌoｃation ／pｏｓitｉon22) 浇口类型—gａtｅtype23) 产品标识—stamp infｏrmaｔion, parｔidentificａtion２４）特殊要求—sｐeciaｌ instructiｏｎs2. 产品质量及外观要求Pａrt Quality & Apｐｅaraｎcｅ１）尺寸及公差Dｉmensioｎ&Toｌｅｒancｅ①重要尺寸—ｃritical dimensｉoｎ,importanｔdiｍ.，kｅy dim.②理论尺寸—ｎｏｍiｎalｄimension③实际尺寸—actuａｌdiｍension④公差—tolｅraｎce⑤公差带—tｏlｅrancｅrａnge⑥尺寸超差—dimensionｄeviａtion⑦接受（合格）—ａccepｔ, OＫ⑧拒绝(不合格）—rejecｔ, refｕse,oｂsolete,NＧ⑨让步接受—conceｓsion, ｓｐecial adｍiｔ⑩返工—re-wｏrk２）产品缺陷（较常见）Ｄefeｃts (normaｌ）①缩印—sｉnk mark, sｈrｉｎｋage②飞边—flａsh, burr③段差—mｉsmａtcｈｄｉｓcｒepancy④银丝纹—ｓｎake ｍaｒks, streak⑤弯曲—warpａｇe, ｄistoｒtion⑥打不足（缺料）—shorｔｓhot⑦熔接线—wｅld lｉne3．产品外观ParｔAｐｐearanｃｅ①产品颜色—paｒｔｃｏｌor②产品光泽—ｇloss③皮纹粒度—gｒain4．常用词汇、词组及短语NormａｌＷｏrd, Shｏｒt Seｎｔｅｎｃe1）单边—per side2)双边—both sides３) 加入,添加—aｄｄ,iｎcorporａtｅ４) 去除，取消—rｅmovｅ,ｃancel５) 满足…的要求,符合,与…要求一致—accｏｒｄing ｔｏ, conｆorｍto, satisfy, mｅeｔ6) 要求，需要—ｒequｉrｅ,neｅｄ,demanｄ7）确认—be ａｐproｖｅｄ, agreedｂy …8) 允许—peｒmｉｔ，ａlloｗ9) 在…范围之内—ｗithin1０）不可以,不允许，禁止—free from，preｖent, avｏid11）…,除非有另指—…unleｓsｏtherwｉｓｅspecified1２）…或少于—…or ｌess13) 自动化运作—automatiｃoperａｔｉoｎ１4）未注尺寸(详细形状）见三维造型Noｎｄimensioned ｃontｏur (dｅｔａiled ｓhape) ｓｅe ３D mｏｄel.15)分型线上的飞边(披缝)或段差应小于…Bｕrrs and diｓｃrｅpａｎcy onｔheＰ／Ｌshaｌl be… ｏr less.五．标题栏Titｌe Bloｃｋ１. 产品名称—part name２．图纸编号+ 版本号(索引号）—draｗｉng no．+ level （ｉndex)3. 一般公差[的标准] —generａl tolerａnｃe（三) 如何阅读制模标准？Hｏw to read toｏling stanｄaｒd?一．模具结构术语Moｌd CｏnsｔrｕctiｏｎTermiｎologyA．模架Mold Ｂａｓe1.模架量化特征Mｅasuremｅnt Feature①长X 宽Ｘ高—ＬeｎgtｈXＷidth X Height②模具推高尺寸（模厚）—sｔａck hｅiｇht ｏf ｍould③模具重量—totａl weight ofｍould,mouｌd thｉｃkｎesｓ2. 定模底板—fｒont pｌaｔe, ｔｏｐclamｐiｎｇplａte, cｌamｐpｌatｅ，clａmｐinｇplate３．定模板—cａvｉty plａｔe，fixｅd moｕlｄplａte, A – platｅ4. 动模板—cｏｒe plａｔe,ｍoｖing mｏｕｌd ｐlate, B – plate５. 支撑板—ｓuppｏｒt plａte, baｃking ｐlate6. 模脚—support bloｃks，raｉlｓ，riseｒs, spａｃeｒblｏｃk７. 顶杆固定板—reｔaining ｐｌatｅ, ejector retainｉｎg plate８. 顶板—ejｅctor ｐlaｔe9．动模底板—baｃｋpｌａte1０．导柱—ｇｕｉde ｐillar, leａｄer pin, ｇuｉdeｐin11．导套—gｕidｅｂuｓh, ｌeadｅr ｐｉnｂush12.复位杆—rｅturn piｎ，push-back ｐｉｎ13．弹簧—ｓpriｎｇ14. 撑头—supｐｏrt pillar１5．推板导柱、导套—ejectiｏn gｕidｅpｉn / ｂush16．挡钉—ｓtop ｐiｎ,stoｐ buttoｎ１７．站立脚—sｔａndiｎg-ofｆpiｌlars18．标牌—pｌaquｅscutcheonB.成型零部件moｕｌding components1９. 型芯—cｏre20．型腔—cavitｙ２1. 镶针—core ｐin２２. 镶块—insｅrt，sｐlit23.滑块—sｌide, sliｄiｎｇsｐlit２4. 斜顶—lifteｒ,angled-liｆt ｓｐlitA 斜顶头—lｉftｅr hｅadB 斜顶杆—ｌifter rod, lｉｆteｒｓｈａft2５. 成型顶杆—ｍoulding facｅpin, form pｉｎC．浇注系统Fｅed System1．塑料Mouldingａ．主流道—ｓｐrueｂ. 分流道runｎer①主分流道— mａin ruｎner ②二级分流道— braｎcｈ rｕnｎeｒ分流道断面形状cｒosｓ-sｅｃtional ｓｈape oｆｒunner①圆形—ｆuｌl roｕｎd②半圆形—semiciｒcｕｌar③梯形—trapｅｚoidaｌｃ．浇口gaｔｅ常用浇口形式nｏrmａl ｇate tyｐe :①边缘浇口（J型浇口) —eｄgｅｇate, J –ｇate②侧浇口—side gate③潜伏式浇口—sub-gaｔe, ｃａshew gatｅ， subsurfａｃｅ gaｔe, suｂmaｒine gaｔe④潜伏式二次浇口(隧道式浇口) —ｔunnｅl gａｔe ontｏfeｅｄer post⑤点浇口—pｉn gａｔe⑥直接浇口(主流道型浇口) —ｓprue gate, direct gａte⑦护耳式浇口—tａb gａted. 模腔—imprｅｓsｉｏnｅ. 冷料井—colｄsｌug welｌf．热流道—hot runner２.模具零件moｌｄcoｍponentsa. 定位圈—lｏｃating ring, lｏｃation ｒing, regｉsｔｅr riｎｇb. 浇口套—spｒue bushc．挡圈—sｔｏp ｒingd．浇口镶块—gate inｓeｒte．热流道板—mａｎifoldｆ. 热嘴—ｈｏｔｄropＤ.分型面及其锁紧、排气Paｒtｉｎg Sｕrfaｃｅ, inter-loｃking＆ventｉng 1．分型线—paｒtｉnｇline ( P/Ｌ）２. 镶拼线—bｏdｙlｉnｅ，ｊoiｎt lｉne3．平/不平的分型面—ｆlａt ／non – flaｔ pａrting sｕrface4．封胶面—sｈut ofｆsurfaces, ｓeａｌ－ｏff suｒfａceｓ5．擦位—shuｔoff6. 碰穿位—kiｓs-ｏff7. 管位—pａrtｉｎgｌinｅｌock８.分型面的释放(避空) —rｅｌieｆｏｆpａｒtiｎg ｓuｒｆａｃe９．分型面的平衡—bａlanｃiｎｇof ｐarｔing ｓurface10．锁紧角度—ｌockｉng anglｅ1１.锁紧力—cｌａｍpingｆoｒce1２．锁模板—safetｙstｒap1３．精定位—Inｔeｒloｃk,die locｋ14．困气—aｉｒtrap1５．排气槽—vent, veｎt ｓlｏtＥ.滑块机构Slide１．驱动Acｔuaｔｉｏｎ①斜导柱—anglｅｄｐin, ｈorn pｉn, cａm pin②弹簧—sprinｇ③油缸—ｈydraulｉc cyliｎder２．制动Dｅｔeｎtion①滑块固定器—sｌide rｅtａｉｎer②弹簧制动器—spｒing-loaded detentｉon (plunger)③挡钉、挡板—ｓtop pin, stop platｅ, slide stop3．导轨—gｉｂ,gｕide sｔrip4．锁紧块(楔紧块)—heel blｏcｋ,ｌｏcking ｈｅel，wｅｄge blｏｃk, cｈasｅbl ｏｃk5. 耐磨片—wear pｌａte，ｗｅar strip6. 压板—reｔaiｎeｒ7. 螺钉—screw８．定位销—dowelＦ.斜顶机构Ｌiftｅｒ1.斜顶头—lｉfｔｅｒｈeａｄ2．斜顶杆—liｆtｅr roｄ，lifｔer ｓhａfｔ3．开口销—spｌit ｐin4．固定板(压板) —reｔaiｎer plａｔｅ5. 耐磨片—wear ｐlatｅ６. 铜导套—ｂrｏnzｅbuｓhing7．衬套—spaｃeｒ８. 导轨—L – gib9. 滑动块—slideG．顶出系统EjectioｎSyｓtem１. 基本词汇Baｓｉc Worｄ①顶出行程—ejectｉｏn stroke②模具开档—ｄayligｈt③粘模—stｉck④产品脱模—part iｓpuｓh ofｆfrom,ｃlearｐart of mouｌd, seｐaratioｎofｐart2. 顶板机构Ejector pｌａｔe asｓembly①顶板(推板) —ｅｊｅｃｔoｒplａtｅ②顶板固定板—retａiniｎg plａte③推板导柱—ejector gｕiｄｅpin④推板导套—ｅjｅctor guide ｂusｈ⑤撑头—supｐort pｉllar, pilｌarｓupport3．复位机构Return Sｙsteｍ①复位杆(回程杆)—return ｐin，ｐush – back pin②挡钉—sｔｏｐpin, sｔop buｔton③压簧—coｍpｒｅsｓeｄsｐring④碟簧—a sｔack of “Ｂeｌleviｌｌｅ”wasｈers⑤早复位机构—ｅａrly return sｙsｔem⑥强制复位机构—posｉtｉve retｕrｎsｙsteｍ4．顶出方法Ejection Techniqｕes１) 顶杆顶出—ｐiｎeｊection２) 顶管顶出—ｓleｅve ejｅction3）顶块顶出—bａr ejｅction４) 扁顶顶出—bｌａde ｅｊｅction５) 顶板顶出—ｓtripper eｊecｔｉon６) 油缸顶出—hydraｕlic ejｅctｉｏn7) 气顶—air ｅjectioｎ8）阀门顶出—valve ejｅｃtion5. 顶出元件Ejecｔｉon Eｌｅments1) 拉料杆—spｒue pｕｌlｅr，sｕckerｐin2) 顶杆—ejector pｉｎ3) 阶梯式顶杆—ｓｔeppｅd eｊｅctor ｐin4) 顶管—eｊeｃtion sleｅｖe，slｅevｅ５）扁顶—ｅjｅcｔor blaｄe, slａbｂeｄoff ejecｔｏr pin6）顶块—striｐper bar7）顶环—strippｅr ｒing８)推板—ｓtripper plate9)加速顶—accｅleｒaｔｅd ejeｃtioｎ6. 顶出辅助机构Supｐlｅmｅntaryｏpｅraｔｉng sysｔem1）弹簧柱塞器—sprｉnｇ–ｌoａdｅｄｐｌunger２）弹珠定位器—baｌl catch ｓyｓtem3) 插销式锁扣—Lａtch– lock4) 尼龙拉杆装置—fｒiｃtion pullｅr ｄeｖice７．电器元件Electrｉc Coｍpｏnents1) 压力传感器—pｒessuｒe trａｎｓduｃer2) 限位开关—ｌimit swｉtchF．冷却系统Ｃooling Ｓysｔem1. 基本词汇BａsiｃWｏrd１)温差—teｍｐerａture variａtion2) 水孔（水道）—ｗaｔｅrｌines, wａtｅr-waｙｓ, flｏw-wａy, cｈannel3) 水路—ｃｏolｉng ciｒcuit4) 水路示意图—wateｒsｃhｅmａtｉc，ｓchematic circuit5) 冷却液—cｏｏlaｎt，coｏlant fluid６）内连接—iｎｔercｏnnｅct7) 外连接—eｘteｒnaｌｃｏｎnectioｎ8）出口、入口—oｕtlｅt、iｎleｔ9) 漏水—ｗａter ｌeakage2. 水路分布Circｕits1)阶梯式水路—steppeｄsyｓteｍ２)喷淋—bａffled holeｓｙstem3) 斜孔式水路—angled hole sｙｓtem3. 水路元件Ｃoｍｐonents1）闷头（螺塞、止水栓) — (threａdlesｓ)brasｓpressure pｌuｇ:feｍale plug & male2）隔水片—bafflｅ3) 密封圈—O – rinｇ4）快插水路接头—ｑuick disconｎｅcｔｆｉｔtinｇ, qｕick coｎneｃｔi ｏｎadaptor5) 弯头—elｂｏｗ６)偶合器（连接器、接头) —adapｔor （iｎcｌｕding a plug & a sｏcket）7）橡皮管—rubbｅｒｈoｓｅ８)分水板—water mａnｉｆolｄG.螺纹、螺纹孔& 螺钉Tｈread,tｈｒead ｈole & ｓcrｅｗ1．螺纹—threａd２. 管螺纹—pipe thｒeaｄ3．螺纹孔—screｗｈｏｌe, tappｅd hｏle4. 起吊孔—ｈandｌｉｎg holｅ, jack scｒｅw hole, eyｅbolt hole５.螺钉—screw6．内六角螺钉—sockeｔheａded cap sｃrｅｗ（s．h.c.s.）7．沉头螺钉—ｆlat headed ｃaｐscrew （f．ｈ.c.s）８. 螺栓—bｏlｔ, eyｅbｏｌｔ9．螺母—ｎuｔ10.锁紧螺母—lｏcknut１1．螺纹标准Tｈｒead Stａｎdａrd①公制标准—Metric②英制标准—Imｐｅｒｉal③英制管螺纹标准—Bｒiｔｉsh Ｓtａndard Ｐｉpe thread （BSP)④美制管螺纹标准—ＮPＴ⑤美制粗螺纹标准—UｎitｅｄCoarse tｈｒeａｄ（UNＣ）⑥美制细螺纹标准—Ｕnｉted Fｉnｅtｈrｅａd（ＵNＦ）H．润滑Ｌubricatiｏn１．润滑槽—greａｓe grooｖe２．加油管—grｅａsｅlｉｎe3．油杯—luｂriｃａtioｎfittｉngI．测量仪器Ｍｅasuring Iｎsｔrｕmｅntｓ1. 游标卡尺—vernierｃaliper2. 千分尺—ｍicrｏmeter3.高度规—ｈeｉght gauｇｅ４. 刻度规—ｄiａｌｇａuge5．三坐标测量仪—Coordinaｔe Ｍeasuｒe Maｃhiｎｅ（CＭM）6．塞规—piｎgauge７．圆角量规—radii gauｇe8．輪廓投影機—proJ.注塑机参数Ｉｎjectｉon MacｈｉｎｅPａrameter1. 注塑机规格参数Ｉｎjecｔiｏn MachineＳpeｃifｉｃation①锁紧类型ｃlamp typea.油缸—hydｒauｌic ｂ．肘杆式—togｇle②垂直注塑机导柱间距—tie baｒverticalｃlｅarance③水平注塑机导柱间距—tie bar hoｒizonｔａlｃｌearancｅ④台板尺寸—platenｄim.⑤最小/最大模厚—molｄheighｔMiｎ. / Mａx., Min./ Max. moldｔhickｎess⑥最小／最大注塑机开档—ｏpen daｙliｇht Min. ／Max.⑦锁紧行程—ｃlamｐsｔroke⑧锁紧力—clampｉng forｃe⑨顶出行程—ejector stroke⑩顶出力—ejector forｃe２. 试模工艺参数Mouｌdiｎg ProcessＰaｒameter，macｈine setting①时间Ｔimer(TM)，seca. 注塑(充填）时间—fｉｌling time, iｎjｅctｉon timeb．冷却时间—cｏolｉnｇtimec. 补缩时间—ｐacｋinｇtimｅｄ.保压时间—holding ｔiｍee. 成型周期—cyｃｌe time②速率、速度Ｖelocｉｔy, ％、spｅed，in/seca．注塑（充填)速度—iｎjectiｏn sｐｅedb．保压速率—ｈｏld pressure velocitｙc．螺杆转速—screw rotatioｎｓｐeed③压力Pressｕｒe(Ｐrs．), psiａ. 注塑压力—ｉｎｊeｃtioｎpressurｅb. 保压压力—ｈoｌd prｅssuｒec．回压(背压）—bａｃk prｅｓsure④温度Temｐeratｕre(Teｍp．）, °Fa．注塑机喷嘴温度—nｏzzlｅｔｅmp.b．料筒前段、中段、后段温度—barrel ｆrｏnt、middle、rear temp.c．模温—mouldｔemp.d．料温—purgｅd resin melt ｔemp．ｅ．空射料温—air sｈot melt tｅmｐ.。
模具专业英文术语大全
模具专业英文术语大全1. Die - 模具2. Mold - 模具3. Cavity - 型腔4. Core - 芯子5. Ejector pin - 顶杆6. Land - 分型面7. Gate - 浇口8. Filleting - 去毛刺9. Trim - 修整10. Draft - 拔模斜度11. Undercut - 底切12. Flash - 飞边13. Warpage - 翘曲14. Shrinkage - 收缩15. Melt flow rate - 熔融指数16. Injection molding - 注塑成型17. Blow molding - 吹塑成型18. Compression molding - 压缩成型19. Vacuum molding - 真空成型20. Overmolding - 包覆成型21. Co-injection molding - 双色注塑成型22. Gas assist injection molding - 气体辅助注塑成型23. Rotational molding - 旋转成型24. Injection compression molding - 注射压缩成型25. Injection blow molding - 注射吹塑成型26. Injection stretch blow molding - 注射拉伸吹塑成型27. Injection transfer molding - 注射传递成型28. Injection foam molding - 注射发泡成型29. Injection gas assisted rotational molding - 注射气体辅助旋转成型30. Injection compression blow molding - 注射压缩吹塑成型31. Injection stretch blow molding - 注射拉伸吹塑成型32. Injection transfer blow molding - 注射传递吹塑成型33. Injection foam blow molding - 注射发泡吹塑成型34. Injection gas assisted transfer molding - 注射气体辅助传递成型35. Injection compression foam molding - 注射压缩发泡成型36. Injection stretch foam molding - 注射拉伸发泡成型37. Injection transfer foam molding - 注射传递发泡成型38. Injection gas assisted foam blow molding - 注射气体辅助发泡吹塑成型39. Injection compression foam blow molding - 注射压缩发泡吹塑成型40. Injection stretch foam blow molding - 注射拉伸发泡吹塑成型41. Injection transfer foam blow molding - 注射传递发泡吹塑成型42. Injection gas assisted compression molding - 注射气体辅助压缩成型43. Injection gas assisted stretch blow molding - 注射气体辅助拉伸吹塑成型44. Injection gas assisted transfer blow molding - 注射气体辅助传递吹塑成型45. Injection gas assisted foam compression molding - 注射气体辅助发泡压缩成型46. Injection gas assisted foam stretch blow molding - 注射气体辅助发泡拉伸吹塑成型47. Injection gas assisted foam transfer blow molding - 注射气体辅助发泡传递吹塑成型48. Injection gas assisted compression foam molding - 注射气体辅助压缩发泡成型49. Injection gas assisted stretch foam blow molding - 注射气体辅助拉伸发泡吹塑成型50. Injection gas assisted transfer foam blow molding - 注射气体辅助传递发泡吹塑成型51. Mold temperature control system - 模具温度控制系统52. Coolant system - 冷却系统53. Ejector system - 顶出系统54. Feed system - 喂料系统55. Packaging machine - 包装机56. Automated guided vehicle (AGV) - 自动导引车（AGV）57. Robotic arm - 机械臂58. Computer numerical control (CNC) machine - 计算机数控（CNC）机床59. Plastics injection machine - 塑料注塑机60. Plastics extruder - 塑料挤出机61. Plastics blow molding machine - 塑料吹塑机62. Plastics injection compression molding machine -塑料注塑压缩成型机63. Plastics injection stretch blow molding machine - 塑料注塑拉伸吹塑成型机64. Plastics injection transfer molding machine - 塑料注塑传递成型机65. Plastics injection foam molding machine - 塑料注塑发泡成型机66. Plastics injection gas assisted rotational molding machine - 塑料注塑气体辅助旋转成型机67. Plastics injection compression foam molding machine - 塑料注塑压缩发泡成型机68. Plastics injection stretch foam molding machine - 塑料注塑拉伸发泡成型机69. Plastics injection transfer foam molding machine - 塑料注塑传递发泡成型机70. Plastics injection gas assisted foam blow molding machine - 塑料注塑气体辅助发泡吹塑成型机71. Plastics injection compression foam blow molding machine - 塑料注塑压缩发泡吹塑成型机72. Plastics injection stretch foam blow molding machine - 塑料注塑拉伸发泡吹塑成型机73. Plastics injection transfer foam blow moldingmachine - 塑料注塑传递发泡吹塑成型机74. Plastics injection molding machine with movable platen - 带活动模板的塑料注塑机75. Plastics injection molding machine with fixed platen - 带固定模板的塑料注塑机76. Plastics injection molding machine with hot runner system - 带热流道系统的塑料注塑机77. Plastics injection molding machine with cold runner system - 带冷流道系统的塑料注塑机78. Plastics injection molding machine with multi-cavity design - 带多腔设计的塑料注塑机79. Plastics injection molding machine with clamping force control - 带夹紧力控制的塑料注塑机80. Plastics injection molding machine with cycle time reduction - 带循环时间缩短的塑料注塑机81. Plastics injection molding machine with energy saving features - 带节能功能的塑料注塑机82. Plastics injection molding machine with high precision control - 带高精度控制的塑料注塑机83. Plastics injection molding machine with automatic tool changing system - 带自动换模系统的塑料注塑机84. Plastics injection molding machine with roboticautomation - 带机器人自动化的塑料注塑机85. Plastics injection molding machine with quality control system - 带质量管理系统的塑料注塑机86. Plastics injection molding machine with process monitoring system - 带工艺监控系统的塑料注塑机87. Plastics injection molding machine with maintenance reminder system - 带维护提醒系统的塑料注塑机88. Plastics injection molding machine with data logging and analysis - 带数据记录和分析的塑料注塑机89. Plastics injection molding machine with remote control and monitoring - 带远程控制和监控的塑料注塑机90. Plastics injection molding machine with safety features - 带安全功能的塑料注塑机91. Plastics injection molding machine with operator interface - 带操作员界面的塑料注塑机92. Plastics injection molding machine with easy cleaning system - 带易清洁系统的塑料注塑机93. Plastics injection molding machine with quick change tooling - 带快速换模装置的塑料注塑机94. Plastics injection molding machine with low noiseoperation - 带低噪音运行的塑料注塑机95. Plastics injection molding machine with high throughput capacity - 带高产量能力的塑料注塑机96. Plastics injection molding machine with energy recovery system - 带能量回收系统的塑料注塑机97. Plastics injection molding machine with environmental protection features - 带环保功能的塑料注塑机98. Plastics injection molding machine with advanced materials compatibility - 带先进材料兼容性的塑料注塑机99. Plastics injection molding machine with customizable options - 可定制选项的塑料注塑机100. Plastics injection molding machine with reliable performance and durability - 具有可靠性能和耐用性的塑料注塑机。
模具定义术语
模具定义术语
以下是一些常见的模具定义术语：
1. 模具（Mold）：用于成型、塑造或制造成型件的工具或装置。
2. 型腔（Cavity）：模具中的空洞部分，用于形成产品的外形。
3. 型芯（Core）：模具中的凸起部分，用于形成产品的内部特征。
4. 模架（Mold Base）：支撑和固定模具部件的框架结构。
5. 模具钢（Mold Steel）：用于制造模具的特殊钢材，具有耐磨、耐高温、耐腐蚀等特性。
6. 分型线（Parting Line）：模具的两个半模之间的分界线，用于分开模具并取出成型件。
7. 浇注系统（Gating System）：模具中用于引导熔融材料进入型腔的通道。
8. 冷却系统（Cooling System）：模具中用于控制温度和散热的装置，以确保成型过程的效率和质量。
9. 顶出系统（Ejection System）：模具中用于将成型件从型腔中推出的机构。
10. 模具寿命（Mold Life）：模具可以使用的预期时间或生产的成型件数量。
模具专业术语
模具专业术语随着社会的发展，各行各业都离不开现代化的生产工艺，其中，模具行业是制造业中的核心产业之一。
而要想在这一领域取得成功，就必须掌握模具专业术语。
本文将详细阐述模具专业术语，以便有需要的人士学习和掌握。
一、模具设计专业术语1.设计参数：指在模具制造中，对各种技术参数进行分析和研究，并根据产品的设计要求进行优化，保证模具加工精度和产品质量。
2.模具结构设计：指根据产品设计要求、工艺要求和材料性能等因素，对模具结构进行设计，以实现模具的各种功能。
3.注塑模结构：指注塑模的结构特点，包括芯箱、模板、顶出、导柱、滑块、拉杆、卡板、喷水口等。
4.高级曲面：指模具设计中涉及到的复杂曲面，如自由曲面、弓形曲面、倒角曲面等。
5.冷却系统设计：指模具的冷却系统，包括水口、水道、水管、温控器等。
二、模具材料专业术语1.模具钢：是用于制造模具的钢材，通常包括普通模具钢、高强度模具钢、特殊合金模具钢等。
2.钢材硬度：指钢材的硬度值，通常用硬度计进行检测。
3.钢材硬化：指将钢材进行热处理，使其硬度、强度等性能得到提高。
4.硬度波动：指模具钢在加工过程中，其硬度值的波动情况。
5.热处理：指通过对钢材加热和冷却的处理，使其获得特定的性能和组织结构。
三、模具加工专业术语1.数控加工：是指使用数控机床进行的加工工艺。
2.精密加工：指对模具进行精密加工，以保证模具的精度和质量。
3.注塑加工：指将原料进行熔化后，通过将其注入模具内部制造成产品的加工工艺。
4.电火花加工：指通过放电加工的方式，对模具表面进行加工处理，从而获得需要的形状和精度。
5.线割加工：是指利用金属丝进行加工，将模具材料割成所需的形状。
四、模具维护与保养专业术语1.加油：指对模具润滑油进行补充和更换。
2.打磨：指对模具表面进行划痕、凹凸处进行修补和磨平。
3.覆膜：指在模具表面涂上一层防腐膜，以保证其寿命和质量。
4.更换配件：指更换模具中的配件，如顶出、喷水口、导柱等。
复制模具专业术语
复制模具专业术语1. 拔模斜度，这可是模具里的一个小魔法呢！就像滑梯一样，有个小角度方便零件从模具里顺利滑出来。
要是没有拔模斜度，零件就像被卡在陷阱里的小兽，出不来啦。
2. 分型面，就如同把一块蛋糕切成两半的那一刀。
在模具里，它清楚地划分开不同的部分。
比如说做一个盒子的模具，分型面就是决定盒子上下部分分开的那条线。
3. 浇口，那是模具的小嘴巴。
塑料或者金属液就从这个小嘴巴流进模具型腔里，就像我们喝水通过嘴巴一样。
如果浇口设计得不好，那整个成型过程就像个饿肚子的人，怎么都吃不饱。
4. 流道，这是原料流动的高速公路呀。
在注塑模具里，塑料沿着流道欢快地奔向型腔。
就好比一群小蚂蚁沿着特定的路线去找食物。
5. 顶出机构，简直就是模具里的小助手。
当零件成型后，它就像个热心肠的用力把零件顶出来。
要是没有顶出机构，零件就只能干着急，被困在模具里了。
6. 冷却水道，像模具的小空调。
它能让模具快速冷却，就像在炎热的夏天给滚烫的东西降降温。
如果没有冷却水道，那模具就像个发烧的病人，一直热得不行。
7. 模架，是模具的骨架。
就像房子的框架一样重要。
没有模架，模具就像没有骨头的软肉，根本立不起来。
8. 镶件，好比是给模具戴的小首饰。
有时候为了做出特殊的形状或者结构，就把镶件安装在模具里。
这就像给一件衣服加上独特的纽扣一样。
9. 型腔，这是原料变身的小房间。
塑料或者金属液进去后就变成想要的形状。
就像面团放进模具型腔变成可爱的饼干形状。
10. 型芯，它是型腔里的主角。
比如做一个有洞的零件，型芯就负责制造那个洞。
就像在做甜甜圈的时候，中间的那个小圆圈就是型芯的功劳。
11. 合模力，就像是把模具紧紧抱住的力量。
如果合模力不够，就像两个人拉手拉得不够紧，模具就会漏料，那可就糟了。
12. 脱模剂，是模具的小润滑剂。
就像给东西上油一样，让零件更容易从模具里出来。
要是不用脱模剂，零件和模具就像两个黏人的小娃娃，分不开。
13. 收缩率，这可是个调皮的家伙。
模具专业英文术语大全
模具英语专业术语模具述语一、入水：gate进入位： gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口： switching runner/gate唧嘴口径： sprue diameter二、流道: runner热流道： hot runner,hot manifold热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴： hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头： connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件： mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板： support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针： ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert 行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut onA-plate,core direct cuton B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length 稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machinecompre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate 垫块 spacer parallel支架 ejector housing. mould base leg压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate 定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate 直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin 物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length接触件电镀层contact plating 接触压力contact pressure接触件中心距contact space 接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printedcircuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board表面安装surface Mounting翘曲warp， bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould 熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time 闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top ClampingPlate Top Plate动模座板 Moving Clamp Plate Bottom ClampingPlate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具标准翻译。
模具专业术语
导板模：导板模：板模是以导板作导向的冲模，模具使用时凸模不脱离导板。
导料板：导料板是引导条(带、卷)料进入凹模的板状导向零件。
导柱模架：导柱模架是导柱、导套相互滑动的模架。
冲模：冲模是装在压力机上用于生产冲件的工艺装备，由相互配合的上、下两部分组成。
切开
切开是将材料沿敞开轮廓局部而不是完全分离的一种冲压工序。被切开而分离的材料位于或基本位于分离前所处的平面。
切边
切边是利用冲模修边成形工序件的边缘，使之具有一定直径、一定高度或一定形状的一种冲压工序。
切舌
切舌是将材料沿敞开轮廓局部而不是完全分离的一种冲压工序。被局部分离的材料，具有工件所要求的一定位置，不再位于分离前所处的平面上。切断
压料筋：压料筋是拉延模或拉深模中用以控制材料流动的筋状突起，压料筋可以是凹模或压料圈的局部结构，也可以是镶入凹模或压料圈中的单独零件。
压料槛：压料槛是断面呈矩形的压料筋特称。
承料板：承料板是用于接长凹模上平面，承托冲压材料的板状零件。
侧刃：侧刃是在条(带、卷)料侧面切出送料定位缺口的凸模。
侧压板：侧压板是对条(带、卷)料一侧通过弹簧施加压力，促使其另一侧紧*导料板的板状零件。
冲槽
冲槽是将废料沿敞开轮廓从材料或工序件上分离的一种冲压工序，敞开轮廓呈槽形，其深度超过宽度。
模架：模架是上、下模座和导柱、导套的组合件，可以带模柄或不带模柄。大多数模架是标准件。
模框：模框是容纳凹模拼块的基体。
顶板：顶板是在凹模或模块内活动的板状零件，以向上动作直接或间接顶出工(序)件或废料。
冲裁
冲裁是利用冲模使部分材料或工序件与另一部分材料、工（序）件或废料分离的一种冲压工序。冲裁是切断、落料、冲孔、冲缺、冲槽、剖切、凿切、切边、切舌、切开、整修等分离工序的总称。
模具专业术语（专业人士一定要收藏）
模具专业术语（专业人士一定要收藏）模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sidesforging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfermolding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plungermold 有肩柱塞式模具burnishing die 挤光模 landed positivemold 有肩全压式模具button die 镶入式圆形凹模loading shoemold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bendingdie 双折冷弯模具extrusion die 挤出模palletizing die叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing)压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavitymold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch formdie 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧?goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating centerpunch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导杆pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slidecore) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushingguide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板。
模具专业术语大全
模具专业术语大全punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销模具零件英语词汇air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger加强筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块模具模板英语词汇feature die 公母模femaledie 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚模具五金零件英语词汇eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guidepad 导料块outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板ribbon punch 压筋冲子bottom plate 下托板(底板)stripping plate 内外打( 脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板cover plate 盖板wire spring 圆线弹簧outerguiding post 外导柱stopscrew 止付螺丝located pin 定位销outer bush 外导套模具冲压英语词汇extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙punch wt. 上模重量模具工程类英语词汇plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模pierce 冲孔forming 成型(抽凸, 冲凸) draw hole 抽孔air vent vale 通气阀anchor pin 锚梢angularpin 角梢baffle调节阻板angularpin 倾斜梢baffleplate 折流档板ballbutton 球塞套ballplunger 定位球塞ball slider 球塞滑块binderplate 压板blankholder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumperblock 缓冲块buster堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底bending 折弯trim 切边emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平模具厂常用标准零配件英语词汇die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowelhole 导套孔dowelpin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模groove 压线blanking 下料stamp letter 冲字( 料号)shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stoppin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/ 锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板××××××××××××××××××××××××××××××××××××××××××××××××××××××××××。
模具专业术语
模具专业术语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold (普通模）边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector sleeve pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes with ejector pin料位出上/下模：part from cavity (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper ele模具专业英语词汇dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出司筒ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢。
模具专用术语词汇
一﹑入水：gate进水位：水口形式：大水口：细水口：水口大小：转水口：唧嘴口径：二﹑流道：runner热流道：热嘴冷流道：唧嘴直流：圆形流道：流道电脑分析：流道平衡：热嘴：热流道板：发热管：探针：插头：插座：密封/封料：三﹑运水：water line喉塞：喉管：塑胶管：快速接头：四﹑模具零件：mold components 三板模：二板模：边钉/导边：边司/导套：中托司：中托边L：顶针板：托板：螺丝：管钉：内模管位：顶针：司筒：司筒针：推板：缩呵：扣机（尼龙拉勾)：斜顶：模胚(架)：上内膜：下内模：行位（滑块）：镶件：压座/斜鸡：耐磨板/油板：压条：撑头：唧嘴：挡板：定位圈：锁扣：扣鸡：推杆：栓打螺丝：顶板：活动臂：分流锥：水口司：垃圾钉：隔片：弹弓柱：弹弓：中托司：中托边：镶针：销子：波子弹弓：喉塞：锁模块：斜顶：斜顶杆：尼龙拉勾：活动臂：复位键﹑提前回杆：气阀：斜导边：承压平面平衡：模排气：回针碰料位：模总高超出啤机规格：顶针碰运水：料位出上/下模：模胚原身出料位：不准用镶件：用铍铜做镶件：初步（正式）模图设计：反呵：弹弓压缩量：稳定性好：强度不够：均匀冷却：扣模：热膨胀：公差：铜公模具术语gate locationgate typeedge gatepin-point gategate sizeswitching runner/gatesprue diameterhot runner,hot manifoldhot sprue/cold runnerdirect sprue gateround (full/half runner)mold flow analysisrunner balancehot spruehot manifoldcartridge heaterthermocouplesconnector plugconnector socketsealwater lineline plugtubeplastic tubejiffy quick connector plug/socker件：mold components3-plate mold2-plate moldleader pin/guide pinbushing/guide bushingshoulder guide bushingguide pinejector retainner platesupport platescrewdowel pinply bar scotcore/cavity inter-lockejector pinejector sleeveejector pinstripper platemovable core,return core core puller nylon latch lockliftermold basecavity insertcore insertslideinsertwedgewedge wear plateplatesupport pillarsprue bushingstop platelocating ringlatchparting lock setpush barS.H.S.Beracuretunlever armspure speraderbushstop pinbufflespring roddie springejector guide bushejector guide pinpindowel pinball catchpipe pluglock plateangle from pinangle ejector rodparting lockslever armearly return barvalvesangle pintermsparting surface support balanceparting line ventingreturn pin and cavity interferencemold base shut hightwater line interferes withejector pinpart from cavith(core)sidecavity direct cut on A-plate,core direct cut on B-plate. Do not use(core/cavity)insertuse beryllium copper insertpreliinary(final)mold designreverse corespring compressed lengthgood stability,stableinsufficient rigidityeven coolingstickingthero expansiontolerance。
模具专业术语
行位是广东模具术语，也是就是指滑块，用来成型一些产品中不能直接分模的结构以下是一些术语产品类加强筋---加强用的骨位 ;美工线---上下盖装配的中间的间隙（可有效防上错位）行位 >滑块 ;司筒 >套筒入子 >镶件（INSERT）入子为台灣叫法 ;斜顶 >斜顶块或斜顶杆KO孔 > 顶棍孔 ;司筒针 > 套筒针撑头 > 支撑柱(防止B板变形的) ;铲鸡 >行位锁紧块治具 > 工具(夹具) ；喉咀 > 水管头；行位波仔 >滑块斜器；中托司 >浇口衬套水口板 >流道板；细水口板 >分流道板勾针 >拉料杆；B板 >动模板；A板 >定模板产品的夹线 >分型线；运水 >冷却水道；回针 >复位顶针；隔热板 >热流道模上用的撬模位 >用来公开AB板的；码模坑 >注射时固定上下模的通框 >把框开成通；大水口模----二板模；小水口模----三板模斜顶(又叫推方)----楣仔方；方铁----凳仔方夹水纹----熔胶线火花纹----电火花加工后留下的纹粗公----电火花粗加工用的铜公精公----电火花精加工用的铜公晒字----做好菲林再拿去加字体的加工方法开模器=拉胶=拉模扣密封圈=膠圈 =防水胶圈=O型圈波子螺絲＝定位珠 =弹弓波子扣机就是控制多板分型的机械装置模具类：K.O孔——顶棍孔——用来顶顶针板的。
塑胶类：赛钢——POM ；防弹胶——PC ；透明大力胶——SAN ；亚加力——PMMA校杯——前模弹出开模的内行位PL面（音啪啦面）——分模面反柯——将正常情况下的前后模料位倒过来开模的方法，比如玩具车模具开模时，如果车外形面放后模出就是反柯浮柯——局部有倒扣的地方采用小镶件弹出的出模方法0.01mm=1丝=一条（台湾） ,不要误导人家啊，1u=0.001MM吃前模：开模时，产品留在前模顶白：顶出时所需脱模力较大，顶针不够力，使产品局部被顶坏，从产品正面看，有明显的白色或者胶位高出，又叫顶高水口烘印：潜水时入水点在制品外观面上留下的痕迹咬花=蚀纹/喷沙；逃料=偷料；多肉＝多料机械类工具类:扳手=士巴拿（spanner）港资厂术语；合金刀=卡凡刀模具类：前模与后模“复模--第一次合模”=飞模=ＦＩＴ模方铁=模脚；模具抛光=省模；周位=点浇口的凹点孔虎口=模仁上的精定位波珠=行位限位螺珠尼龙扣=一种模具分型开闭器超不碎胶 ABS(工程塑料)赛钢 POM ；硬胶 GPPS不碎硬胶 HIPS ；软胶 PE尼龙 PA ；防弹胶 PC百折胶 PP ；亚加力 PMMA(有机玻璃) ；K料 (K胶，学名BS 缩水1.005，是一种透明料)模具類 (順德)吊針 ---三板模前模拉料針撐雞------鎖緊塊(又稱鏟基)彈啤－－－裝彈簧的斜滑塊模具工程类的：钢模：塑胶模；棱线：过渡线。
模具专业术语12页
各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die压紧模fishtail die 鱼尾形模具profile die轮廓模flash mold 溢料式模具progressivedie 顺序模gypsum mold 石膏铸模protablemold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing)压花起伏成形re-entrant mold 倒角式模具sectionaldie 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positivemold 半全压式模具shaper 定型模套single cavity mold单腔模具solid forging die 整体锻模splitforging die 拼合锻模split mold 双并式模具spruelessmold 无注道残料模具squeezing die 挤压模stretch form die拉伸成形模sweeping mold 平刮铸模swing die振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold通用模具unscrewing mold 退扣式模具yoketype die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板centerpin 中心梢clamping block 锁定块coil spring螺旋弹簧cold punched nut 冷冲螺母coolingspiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejectorleader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指第 1 页形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧? goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block歧管档块master plate 靠模样板match plate分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster换模保持装置moving bolster plate 可动侧模板onepiece casting 整体铸件parallel block 平行垫块paring line分模线parting lock set 合模定位器passguide 穴型导板peened head punch 镶入式冲头pilotpin 导?pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runnerlock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套spruebushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料?spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套stripperplate 剥料板stroke end block 行程止梢submarinegate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copyshaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine ?孔机engravingmachine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine第 2 页内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂?床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机检验量测工具用语autocollimator 自动准直机bench comparator 比长仪block gauge 块规bore check 精密小测定器calibration 校准caliper gauge 卡规check gauge 校对规clearance gauge 间隙规clinoretee 测斜仪comparator 比测仪cylinder square 圆筒直尺depthgauge 测深规dial indicator 针盘指示表dial snapgauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge测高规inside calipers 内卡钳insidemicrometer 内分??卡interferometer 干涉仪leveling block平台limit gauge 限规micrometer 测微计mil 千分之一寸monometer 压力计morse taper gauge 莫氏锥度量规nonius 游标卡尺optical flat 光学平晶optical parallel光学平行passimeter 内径仪position scale 位置刻度profile projector 轮廓光学投影仪protractor 分角器radius 半径ring gauge 环规sine bar 正弦量规snap gauge 卡模square master 直角尺stylus 触针telescopic gauge 伸缩性量规working gauge 工作量规模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢highspeed tool steel 高速度工具钢hot work die steel 热锻模用钢lowalloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchantiron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainlesssteel 不锈钢tin plated steel sheet 镀锡铁板toughpitch copper 韧铜troostite 吐粒散铁tungsten steel ?钢vinyl tapped steel sheet 塑胶覆面钢板表面处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloytreatment 阿托木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理boxannealing 箱型退火box carburizing 封箱渗碳brightelectroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemicalvapor deposition 化学蒸镀第 3 页coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ioncarburizing 离子渗碳处理ion plating 离子电镀isothermalannealing 等温退火liquid honing 液体喷砂法lowtemperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitationhardening 析出硬化press quenching 加压硬化processannealing 制程退火quench ageing 淬火老化quenchhardening 淬火quenching crack 淬火裂痕quenchingdistortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness红热脆性residual stress 残留应力retainedaustenite 残留奥rust prevention 防蚀salt bathquenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stressrelieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理underannealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuumheat treatment 真空热处理vacuum nitriding 真空氮化waterquenching 水淬火wetout 浸润处理焊接用语acetylene 乙炔ampere 电流安培angle welding 角焊arc 电弧argon arc welding 氩弧焊接bareelectrode 光熔接条butt welding 对接焊接camber 电弧弯曲cascade 阶叠熔接法clad weld 被覆熔接crator 焊疤excess metal 多余金属filler rod 焊条fillet weld 填角焊接gas shield 气体遮蔽groove welding起槽熔接hand face shield 手握面罩hardfacing 硬表面堆焊第 4 页jig welding 工模焊接laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法plug welding 塞孔熔接positioned welding 正向熔接pressure welding 压焊propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜root running 背面熔接seam 焊缝seaming 接合seam welding 流缝熔接series seam welding 串联缝熔接skip welding process 跳焊法spark 火花spot welding 点焊接stitch welding 针角焊接stud arc welding 电弧焊接under laying 下部焊层void 焊接空隙weld flow mark 焊接流痕weld flush 焊缝凸起weld line 焊接纹weld mark 焊接痕weld penetration 熔接透入weld zone 焊接区welding 焊接welding bead 焊接泡welding direction 焊接方向welding distortion 焊接变形weldingflux 焊剂welding ground 电熔接地weldinginterval 焊接周期welding stress 熔接应变weldingtorch 熔接气炬射出成形关联用语activator 活化剂bag moulding 气胎施压成形bonding strength 黏合强度breathing排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 著色剂color matching 调色colormasterbatch 色母料compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded beadsealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floatingplaten 活动模板foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injectionplunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method配合成形法mould clamping force 锁模力mouldrelease agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 後固化premix 预混料purging 清除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology流变学sheet 塑胶片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率塑胶原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CAcellulose acetate butyrate 醋酸丁酸纤维素CABcomposite material 复合材料cresolresin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑胶epoxyresin 环氧树脂EPethyl cellulose 乙基纤维素ethylenevinylacetate copolymer 乙烯-醋酸乙烯EV Aethylene-vinlacetate copolyme 醋酸乙烯共聚物EVA expanded polystyrene?泡聚苯乙烯EPSfiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF第 5 页nitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑胶polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PA polybutyleneterephthalate 聚对苯二甲酸丁酯PBTpolycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETPpolymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POMpolyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPO polypropylene 聚丙烯PP polystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PUpolyvinylacetate 聚醋酸乙烯PV AC polyvinylalcohol 聚乙烯醇PV A polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVCpolyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDCprepolymer 预聚物silicone resin 矽树脂thermoplastic 热塑性thermosetting热固性thermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差atomization ?化bank mark ?料纹bite 咬入blacking hole 涂料孔(铸疵) blackingscab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮摺叠straightening矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱摺surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹模具常用刀具与工作法用语adjustable spanner 活动扳手anglecutter 角铣刀anvil 铁? arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convexcutter 凸形铣刀cross joint 十字接头cutting edgeclearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头第 6 页polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手电脑关联用语3D modeling 三次元模拟access 通路animation 卡通影片application 应用board 基板bug 故障bus 汇流排CAD 电脑辅助设计CAE 电脑辅助工程分析CAM 电脑辅助制造cassette 卡座color display 彩色显示器command 指令communication 通信compact 精简小型computer 电脑copy 复制cursor 游标curve modeling 曲面模拟database资料库design 设计digitizing 数位化disk 磁碟dot 点eyelet 眼孔floppy 磁碟片format 格式化graphic 圆解hardware 硬体honeycomb 蜂巢interface 界面know how 秘诀laser printer 雷射印表机lay out 布置memory 记忆memory swap 交换记忆microprocessor 微处理器modeling造型module 模组monitor 萤幕mouse 滑鼠need 需求network 网路new version 新版on line 上线中option 选择PC 个人电脑plotter 绘图机program 程式scanning 扫描simulation 模拟software 软体solid model 实体模型system 系统tape 磁带terminal 终端机texture 构造trim 修边venter 排气风扇word processor 文书处理器各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工caulking ?合加工coining 压印加工compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 叠板裁断drawing引伸加工drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工finishblanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 摺叠加工forming 成形加工impact extrusion冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting ?接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining无废料加工seaming 折弯重叠加工shaving 缺口修整加工shearing 切断加工sizing 精压加工/矫正加工slitting 割缝加工spinning 卷边?接staking ?固stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴blankdetermination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面第 7 页camlachie cramp 铸包casting on flat ?合chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blankingpress 精密下料冲床forging roll 辊锻机finishing slag 炼後熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rackpinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造keyclutch 键槽离合器knockout 脱模装置knucklemechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路控制器lowerdie 下模micro inching device 微寸动装置microinching equipment 微动装置motor 马达moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusherfeeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking反转下料robot 机器人roll forming machine辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safetyguard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造separate分离shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 收缩配合shut height闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole逃料孔spin forming machine 旋压成形机spotting 合模stack feeder 堆叠拨送料机stickness黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置strippingpressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer传送transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机线切割放电加工关连用语abnormal glow 不规则辉光放电arcdischarge 电弧放电第 8 页belt 皮带centreless 无心chrome bronze 铭铜clearance angle 後角corner shear drop 直角压陷deflection 桡曲度discharge energy 放电能量dressing 修整dwell 保压flange 凸缘gap 间隙graphite 石墨graphite contraction allowance 电极缩小余量graphite holder 电极夹座hair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极pulse 脉冲rib working 肋部加工roller electrode 滚轮式电极rotary surface 旋转面shank 柄部sharp edge 锐角部tough bronze 韧铜traverse 摇臂tungsten bronze ?青铜waviness 波形起伏work 工件working allowance 加工余量working dischard 加工废料锻铸造关连用语accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning 离心喷光allcore molding 集合式铸模all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand背砂base bullion 粗金属锭basepermeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落锤bottompour mold 底浇bottom pouring 底注boxless mold脱箱砂模break-off core 缩颈砂心brickmolding 砌箱造模法buckle 剥砂面camber 错箱camlachie cramp 铸包cast blade铸造叶片casting flange 铸造凸缘casting onflat 水平铸造chamotte sand 烧磨砂charginghopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂coretemplate 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心filling in 填砂film play 液面花纹finishing slag 炼後熔渣flash gutter锻模飞边槽flask molding 砂箱造模forging roll辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investmentcasting 失模铸造isothermal forging 恒温锻造loosepiece 木模活块molding pit 铸模地坑pouringprocess 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand粗砂roughing forge 粗锻sand crushing塌箱seamless forging 无缝锻造separate分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tapcasting 顶注top gate 顶注浇口unworked casting不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件模具加工方法barrel 滚筒(加工) bending 波纹加工broaching 拉刀切削centering 定中心cutting 切削cylindrical lathe cutting外圆车削electric discharge machine 放电加工electrolytic grinding 电解研磨embossing 压花加工facing 面车削filing 锉刀修润hand finishing 手工第 9 页修润hemming 卷边加工hobbing 滚齿加工joggling 摇动加工lapping 抛光/研磨修润laser beam machining 雷射加工lathe cutting 车床车削planning 刨削加工polishing 抛亮光reaming 铰孔修润rough machining 粗切削rounding 圆形加工sawing 锯削scaling 清除钢碇缺陷shaping 成形加工skiving 表面研磨slotting 切缝切削taper turning 锥度车削thread cutting 螺纹切削ultrasonic machining 超音波加工up cut milling 逆铣加工学理实验与试验用语air permeability test 透气性试验austenitic steel 沃斯田铁钢brinell hardness 布耐内尔硬度brinell hardness test 布氏硬度试验charpy impact test 夏比冲击试验conical cup test 圆锥杯突试验cup flow test 杯模式流动度试验dart drop impact test 落锤冲击试验Elmendorf test 埃罗门多撕裂强度试验environmental stress cracking test 环境应力龟裂试验ericessen test 埃留伸薄板拉伸试验falling ball impact test 落球冲击试验fatigue test 疲劳试验ferrite 纯铁体gantt chart 甘特图heat cycle test 热循环试验histogram 柱状图hot bend test 热弯试验izod impact test 埃左德冲击试验loop tenacity 环结强度martens heat distortion temperature test马顿斯耐热试验martensite 马氏体mullen burstingstrength tester 密廉式破裂强度试验机nol ring test 诺尔环试验normaldistribution 常态分配ozone resistance test 抗臭氧试验pareto diagram 柏拉图peeling test 剥离试验pinhole test 针孔试验机rattler test 磨耗试验rockweelhardness test 洛氏硬度试验rockweel hardness 洛氏威尔硬度rolinx process 罗林克斯射出压缩成形法rossi-peakes flow test 罗西皮克斯流动试验sampling inspection 抽样检查scratch hardness 抗刮硬度shorehardness 萧氏硬度spiral flow test 螺旋流动试验surfaceabrasion test 表面磨耗试验taber abraser 泰伯磨耗试验机tensileimpact test 拉伸冲击试验tensile strength 抗拉强度tension test张力试验thermal shock test 冷热剧变试验torsion test 扭曲试验ubbelohde viscometer 乌别洛德黏度计vicat indentation test 维卡针压陷试验Vickers hardness test 维氏硬度试验warpage test 翘曲试验weatherometer 人工老化试验机weissenberg effect 威森伯格回转效应砂轮用语abrasive 砂轮Al2O3 氧化铝balance 平衡bond 结合borazon 氧化硼立方晶buffing wheel抛光布轮diamond 钻石dresser 砂轮整修机dressing 修整endless grinding belt循环式研磨带finishing allowance 加工余量grain磨粒grinding disc 研磨盘jamp up 孔眼堵塞mesh 网筛目parameter 参数resinoid grinding wheel 半树脂型砂轮slitting 切缝量vitrified 陶瓷的wheel 旋转机械设计及周边其他用语assembly drawing 装配图auto toolchange cycle 自动换刀时间周期beam 横梁bending moment 弯矩bending stress 弯曲应力bottoming底靠buckling 纵弯曲chamfering 去角斜切channel 凹槽chattering 颤动check point 查核点chip 切屑chip conveyor 排屑输送机coefficient of friction 摩擦系数compact 小型的cooling pipe 冷却管coupon 试样胚deflection 挠曲量distortion 扭曲变形draft taper 拔模锥度draw out 拉拔fit tolerance 配合公差flexible rigidity 弯曲刚性gas vent气孔hatching 剖面线heater cooler 加热器冷却装置hook cavity 钩穴inching 寸动lug 凸缘maintenance 维修保固metallurgy 冶金学notch effect 切口效果out of roughness 真圆度performance动作性能pit 坑plane strain 倒角应力第 10 页plug mill 蕊棒轧管机repeated load 重覆载荷riveted joint ?钉接合sand paper 砂纸shift 偏移shrink fit 热压配合shrinkage hole 缩孔sinking 凹陷sketch 草图spalling 剥落straightness 直度submarine 深陷式surface roughness 表面粗度tapping 攻螺丝thermocouple 热电耦torsion load 扭转载荷toughness 韧性tracing 描图under cut 凹割业务与贸易关连用语accept order 接受订货account 帐户after service 售后服务amendment 修正annual sales 年销售额at sight 见票即付balance 余额bank draft 汇票bargain goods 廉价品batch 批次bid 出价bid sales 投标买卖bill of landing 提单bills receivable 应收票据brand 品牌bulk cargo 散装货business transaction 商业交易buyer 买方carbon copy 打字副本cargo collection 揽货carton 纸箱cash in advance 预付现金catalogue 型录cheque 支票CLF 运费保险费在内价格claim 索赔clearance goods 清仓品commision佣金commission 批发商complain 抱怨container 货柜correspondence bank往来银行cost 成本cost and freight; C&F 含运费价格custom broker 报关行customer 客户D/A 承兑交单D/P 付款交单deferred payment 分期付款deferredshipment 分期装运delivery on spot 当场交货deliverytime 交期delivery order 交货单discount 折扣discount on draft 贴现documentarydraft 跟单汇票down payment 订金enclosure 附件endorsement 背书enquete 调查exhibition 展览会export 出口factory visiy 工厂参观favourableprice 合宜价格foreign exchange 外汇free on board船上交货价idea price 希望价格import 进口Japanese Industrial 日本工业规格invoice 发票L/C 信用状margin 利润market 市价net weight 净重no payment 拒绝付款odd item 零头offer 报价open account 交互计算order 订单over looked 疏漏packing 包装pamphlet 小册子partial shipment 分批装船patent 专利paying price 合算价格paymentmethod 付款方式port of destination 目地港port oftrans-shipment 转口港price 价格price decending 减价price rising 涨价procurement 采办prompt delivery 即时交货purchase购入purchasing agent 采购代理商quotation 报价单rebate 回扣reference 查询remittance 汇款repeat order 追加订货request letter 请求函rumor 风评second hand goods 二手货shipper货主shipping 装船shipping mark 麦头shipment 出货sold out 卖完sole agent 总代理商special discount特别折扣specification 规格sample order 指样订货standing 信用情形storage charge 仓租subcontract 外包subject to finalconfirmation 有待确认之报价supplier 供应商T/T 电汇tie-in sale 搭售trade fair 商展会trans-shipment 转运transferred 已转运wharf 码头A3D coordinate measurement 三次元量床3D modeling 三次元模拟aberration 色差abnormal glow 不规则辉光放电abrasive 砂轮access 通路account 帐户accretion 炉瘤accurate die casting 精密压铸acidconverter 酸性转炉acid lining cupola 酸性熔铁炉acidopen-hearth furnance 酸性平炉activator 活化剂acetylene 乙炔adjustable spanner 活动扳手aerator松砂机after service 售後服务age hardening时效硬化ageing 老化处理air hardening 气体硬化airless plasting cleaning 离心喷光airpatenting 空气韧化air permeability test 透气性试验airset mold 常温自硬铸模第 11 页。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
精心整理
精心整理模具专业术语大
精心整理
punch 冲头 insert 入块(嵌入件)deburringpunch 压毛
边冲子groovepunch
压线冲子stampedpunch 字模冲子roundpunch
圆冲子
specialshapepunch 异形冲子 bendingblock 折刀 roller 滚轴
baffleplate 挡块 locatedblock 定位块supportingblockforlocation 定位支承块
topplate 上托板（顶板） topblock 上垫脚punchset 上模座punchpad 上垫板punchholder 上夹板stripperpad
脱料背
板upstripper 上脱料板maledie 公模(凸模) innerguidingpost 内导柱 innerhexagonscrew 内六角螺钉
dowelpin 固定销coilspring 弹簧lifterpin 顶料销 模具零件英语词汇 aircushionplate 气垫板 air-cushioneject-rod 气垫顶杆trimmingpunch 切边冲子
stiffening ribpunch =stinger 加强筋冲子
reel-stretch punch 卷圆压平
冲子
guideplate 定位板 slidingblock 滑块 slidingdowelblock 滑块固定块 activeplate 活动板 lowerslidingplate 下滑块板 upperholderblock 上压块
模具模板英语词汇
featuredie 公母模
uppermidplate 上中间板
springbox 弹簧箱 spring-boxeject-rod 弹簧箱顶杆spring-boxeject-plate 弹簧箱顶板bushingbolck 衬套 coverplate 盖板guidepad
导料块
outerstripper 外脱料板innerstripper 内脱料板lowerstripper 下脱料板ribbonpunch 压筋冲子 bottomplate
下托板(底
板)strippingplate 内外打
外
脱料板下脱料板 外导
extensiondwg 展开图 proceduredwg 工程图 diestructuredwg 模具结构图
material 材质
materialthickness 料片厚度pressspecification 冲床
规格dieheightrange 适用模
高dieheight 闭模高度 burr 毛边 gap 间隙
punchwt.上模重量
精心整理
plaindie 简易模piercedie 冲孔模formingdie 成型模progressivedie 连续模gangdies 复合模shearingdie 剪边模rivetingdie 铆合模
pierce 冲孔 forming 成型(抽凸,冲凸)drawhole 抽孔 airventvale 通气阀anchorpin 锚梢angularpin 角梢baffle
调节阻板
angularpin 倾斜梢baffleplate 折流档板ballbutton 球塞套ballplunger 定位球塞ballslider 球塞滑块binderplate 压板blankholder 防皱压板blankingdie 落料冲头bolster 上下模板bottomboard 浇注底板bolster 垫板 bottomplate 下固定板 bracket 托架bumperblock 缓冲块buster
堵口 castingladle 浇注包castinglug 铸耳cavity 模穴(模仁) cavityretainerplate
模穴托
板 centerpin
中心梢
clampingblock
锁定
块coilspring 螺旋弹簧 coldpunchednut 冷冲螺母coolingspiral 螺旋冷却栓
core 心型 corepin 心型梢cotter 开口梢cross 十字接头cushionpin
缓冲梢
diaphragmgate 盘形浇口dieapproach 模头料道diebed
型底
bending 折弯trim 切边emboss 凸点dome 凸圆 semi-shearing 半剪stampmark 冲记号deburrorcoin 压毛边punchriveting 冲压铆合sidestretch 侧
冲压平reelstretch 卷
圆压平
模具厂常用标准零配件英语词汇
dieblock 块形模体diebody 铸模座diebush 合模衬套draft 拔模锥度
drawbead
张力调整
杆drivebearing 传
动轴承ejectionpad
顶出衬垫
ejector 脱模器
ejectorguidepin 顶出导梢ejector leader busher 顶出导梢衬套
ejectorpad 顶出垫ejectorpin 顶出梢ejectorplate 顶出板ejectorrod 顶出杆ejectorsleeve 顶出衬套ejectorvalve 顶出阀eyebolt 环首螺栓fillingcore 椿入蕊
filmgate 薄膜形浇口 fingerpin 指形梢 finish machined
plate 角形模
精心整理
groove 压线 blanking 下料 stampletter 冲字(料号)shearing 剪断
tick-marknearside 正面压印 tick-markfarside 反面压印 板
finishmachinedroundplate 圆形模板fixedbolsterplate 固定侧模板flangedpin 带凸缘销
flashgate 毛边形浇口
flask 上箱 floatingpunch 浮动冲头 gate 浇口 gateland 浇口面gib 凹形拉紧楔gooseneck
鹅颈管
guidebushing
引导衬套
guidepin 导梢guidepost headpunch
顶头冲孔
headlesspunch 直柄冲头heavilytaperedsolid 整体模蕊盒hosenippler 管接头
impactdamper 缓冲
器
injectionram 压射柱塞insert
嵌件
insertpin
嵌件梢
kingpin 转向梢 kingpinbush 主梢衬套landarea 合
模面leaderbusher
导梢衬套liftingpin 起模顶销lining
内衬
locatingcenterpunch 定位
中心冲头 locatingpilotpin
定位导梢
精心整理
locatingring 定位环lockblock
压块
lockingblock 定位块lockingplate 定位板loosebush 活动衬套makingdie 打印冲子
manifoldblock 歧管档块masterplate 靠模样板matchplate 分型板moldbase
塑胶模座
moldclamp 铸模紧固夹moldplaten 模用板
movingbolster 换模保持装置movingbolsterplate 可动侧模板onepiececasting 整体铸件parallelblock 平行垫块 paringline 分模线
partinglockset 合模定位器
passguide 穴型导板
peenedheadpunch 镶入式冲
头
pilotpin 导销pingate
针尖浇
口plate 衬板 preextrusionpunch 顶挤冲头
punch 冲头puncher 推杆pusherpin 衬套梢rack 机架 rappingrod 起模杆
re-entrantmold
凹入模
retainerpin 嵌件梢retainerplate 托料板returnpin 回位梢 ridingstripper 浮动脱模器 ringgate 环型浇口roller 滚筒runner
流道
runnerejectorset 流道顶出
器runnerlockpin 流道拉梢screwplug
头塞
setscrew 固定螺丝shedder 脱模装置shim 分隔片
shoe 模座之上下模板 shoot 流道
shoulderbolt 肩部螺丝 spueline 合模线squarekey 方键squarenut 方螺帽squarethread 方螺纹stopcollar 限位套stoppin
止动梢
stopring 止动环stopper 定位停止梢straightpin
圆柱销
stripperbolt 脱料螺栓 stripperbushing 脱模衬套stripperplate
剥料板
strokeendblock 行程止梢submarinegate 潜入式浇口
支撑支柱/顶出支 托板造模刮
/锥形梢 三条螺纹
拉丝模板×。