Snap-on扭矩工具的使用

合集下载

汽车扭力扳手操作方法

汽车扭力扳手操作方法
1.确定汽车的扭矩规格：首先需要确定汽车零部件需要的扭力数值，例如轮胎螺丝需要扭力为100英尺磅。

2.选择正确的扭力扳手：根据需要的扭力数值选择合适的扭力扳手。

扭力扳手通常可以手动调整扭矩数值。

3.设置扭矩数值：将扭力扳手的扭矩数值调整至所需的数值，例如将扭力扳手设置为100英尺磅。

4.固定扭力扳手：将扭力扳手固定在汽车零部件上，通常是通过手柄上的压住按钮将其保持在位。

5.使用正确的插头：根据零部件的型号选择适当的插头，并将其连接到扭力扳手上。

6.操作扭力扳手：将扭力扳手插头对准螺丝或螺母，并用适当的力使其与零件连接。

7.检查扭力数值：在连接过程中，当扭力达到所需数值时，扭力扳手会发出声音或有其他指示，此时应停止扭动。

8. 松开扭力扳手：完成扭力操作后，将扭力扳手从零件上取下，并重置扭力数值。

请注意，扭力扳手的使用需要谨慎，确保使用正确的扭矩数值，否则可能引起松动或损坏零部件。

如果不确定操作的方法，请寻求专业人士的帮助。

Snap-on 分公司 Geoliner 920 中重型车轮对齐仪说明书

geoliner™ 920HD TRUCK WHEEL ALIGNERA division of Snap-on. Incgeoliner™ 920MEDIUM TO HEAVY-DUTYTRUCK ALIGNERTHINK BIGA division of Snap-on. IncSNAP-ON IS THE LARGESTAUTOMOTIVE EQUIPMENT MANUFACTURER IN THE WORLDWE HELP MORE PEOPLE DAILY, WITH CRITICAL TASK SOLUTIONS WORLDWIDE, THAN ANY OTHER AUTOMOTIVE SERVICE EQUIPMENT COMPANYOUR LEGACYA division of Snap-on. IncOUR COMPETITORS USE OUR TECHNOLOGYA division of Snap-on. IncA division of Snap-on. Inc BEST IN CLASS TRAININGTRAINING WHEN YOU NEED IT•AT YOUR OWN PACE•CERTIFIED COURSE•OPTIMIZE YOUR KNOWLEDGE •MINIMIZE YOUR TRAINING EXPENSE•INCREASE YOUR SHOP’SPRODUCTIVITY The Snap-on Training group develops and delivers training for individuals as-well-as for groups.•Wheel alignment geometry Level 1 and Level 2•OEM specific wheel alignment training•Equipment specific training•Group assessment `GRID TRAINING WEBSITE USERS 2018HOFMANN TRAINING WEBSITE USERS 2018geoliner™ 920 MEDIUM TO HEAVY-DUTY TRUCKALIGNERgeoliner™ 920With the Hofmann®geoliner®920, checking wheel alignment on heavy-duty vehicles is faster and easier than ever before. Support for a wide range of vehicles, the geoliner920 wheel alignment system can perform alignments on everything from medium-duty trucks to mobile cranes.•Part Number: EEWA820A [Permanently Mounted Targets]•Part Number: EEWA820B[Mobile Targets]•Both units can be utilized outside in the sun•Cannot be utilized outside in the rain or snow•Cannot be utilized outside if windyFEATURESWith the Hofmann geoliner™ 920, checking wheel alignment on a vehicle is faster than ever before. •Class 1 Bluetooth communication •Lightweight•Battery powered•Rechargeable•Batteries run for up to 12 hours and recharge in 5 hoursDedicate one or more spaces in the workshop to wheel alignment and perform measurement diagnoses on assembly line levelEASY TO USE SOFTWARE •Intuitive•Intelligent•Designed specifically for the commercial and industrial level vehicles•Power units•Trailers•Articulated buses450.4 billion miles traveled by all registered trucks in 2015 x .043 cents per mile = $19,367,200,000 billion dollars in tireCRITICALTASKSREQUIRE SPECILALIZED EQUIPMENTIT MAKE SENSE Get it done fast andon timeMinimize truckdowntimeMaximize tire lifeOptimize fueleconomyPLANNED MAINTENANCEMaintenance isunavoidableUnnecessarymaintenance isunprofitableCheck your fleet wheel alignment often and plan accordinglyDragging yourbusinessDepleting yourmargins Increasing your costof operation MANY TRUCKS &HIGH MAINTENANCECOSTWe can helpFASTEST SHORTEST SETUP TIMEMount all clamps and all wheels then start to measureUp to 10 axles can be measured at onceFASTESTFASTEST ALIGNMENT CHECKS•Inspect all vehicles and determine the condition of the wheel alignment•With the permanent target installation mount, checking the alignment has never been so easy•Bring the vehicle to the alignment are, mount all clamps, select the vehicle configuration andproceed to measure the wheel alignmentROIEXPLORE YOUR OWN ROIEven using the most conservativenumbers reveal the how fast return on iswith the geoliner™ 920Let us help you with the ROIRETURN ON INVESTMENTInvestmentProfitLet your Hofmann representative help you with the return on investment Parts and LaborBROADEST VEHICLE COVERAGE•Medium duty trucks•Commercial vehicles•Industrial application•Military•Class 5 through class 8WHEEL ALIGNMENT –I-TRACK•Facts:•Uses a spinning laser•Uses frame geometrical centerline as reference•Can measures all wheel angles, but focusses on speed by measuring toe related angles and camber using a singleroll.•Benefits:•Measuring unit has huge FOV•Can measure absolute angles•Measurement of articulated busses•Customers:•Tire workshops•Fleet customersHD TRUCK WHEELBASE MEASUREMENTUnlike a passenger car, the wheelbase is measured from the front axle to mid-point of the rear tandem axle. The cross dimension is irrelevant.WHEELBASEALL WHEELS HEADED IN THE SAME DIRECTIONREAR TANDEM SCRUB CONDITIONREAR THRUST LINE CONDITIONREAR TANDEM SCRUB CONDITIONAREA REQUIREMENTS Max. width = 16 feetRecommended width = 13 feetMin. width = 11 feet 5 inchesMax length = 72 feetPERMANENT INSTALLATION SET UPVEHICLE CONFIGURATION •Build and save vehicleconfigurations for your fleet ofpower units and trailers•Retrieve the configuration laterVEHICLE CONFIGURATION Easy power units and trailer configurationSimply enter the preferred specification and tolerancerange for:•Toe•Camber•Out of square•ParallelismSave the new vehicle configurationMost comprehensive vehicle database in the industry,including twin-steer axlesTRACTORBUSES1 Front Engine Bus, 4X22 Rear Engine Bus, 8X23 Rear Engine Bus, 4X24 Rear Engine Bus, 6X25 Under Floor Mid Engine Bus, 4X26 Rear Engine Bus, 6X27 Transverse Rear Engine, 4X28 Articulated rear engine Bus, 6X29 Side Mounted Mid Engine Bus, 4X210 Articulated Mid Engine bus, 6X211 Side Mounted Rear Engine Bus, 4X212 Articulated Transverse Rear Engine Bus, 6X2ALIGNMENT SPECIFICATIONSTotal Vehicle Wheel AlignmentAfter fuel, tires are an owner-operator's biggest operating expense. With a set of 10 tires costing thousands of dollars, getting the most out of those tires is a high priority for owner-operators.by Paul Abelson 2000Alignment and tire pressure are the two factors that influence tire wear the most.Alignments raise a lot of questions from owner-operators. How often should I have an alignment done?Does my new truck need an alignment?Where can I get a "good" alignment done?The Maintenance Council (TMC) has a "Recommended Practice" in the final stages of approval regarding "Total Vehicle Alignment." The document, RP 642, carries the long but descriptive title, "Total Vehicle AlignmentRP 642 was developed cooperatively by all the truck builders, drivetrain suppliers, major tire makers and re-treaders, major suspension manufacturers and alignment equipment makers. Its stated purpose is to provide "procedures to identify, record, document and analyze instances in which vehicle components or manufacturing processes fail to meet user expectations." It also offers guidelines for selecting and evaluating both alignment equipment and service providers. The RP recognizes that some things require adjustment or maintenance, especially during break-in. As they relate to tire life, they are discussed throughout the RP. The following are highlights from the RP. They are meant to give you an overview, but are no substitute for the entire document. The quotations are used with the permission of The Maintenance Council.ARE LEGACY ACQUIRED WHEEL ALIGNMENT CORRECTIONS STILL ACCEPTABLE?IS CAMBER ADJUSTABLE ON THE FRONT AND OR REAR AXLES?ADDITIONAL SPECIFICATIONS Enter additional preferred specifications andtolerance ranges for:•Caster•KPI•Max turn•Toe-out-on-turns (TOOT)WHEEL SIZE SELECTOR•For the ideal toe setting•Existing tire sizes can deleted , as well new tire sizes can be created.•You can also rearrange the order ion which the tire sizes are presented by usingGUIDE PROCESSSecond phase of compensation move thevehicle forwardSoftware guides the technician during certain operations Instructions are clearly indicated onthe screenThe software willinstruct the technician when tostopTEXT STYLE COMPREHENSIVE REPORT•Technical report•Intended for the technicianGRAPHIC STYLE REPORT•Visual report•Intended for the vehicle customerMONTY® 5800WLHeavy-Duty Truck TireChanger PREMIUM SERVICE Extremely wide clamping range for rims of 4" –58" without extensions, high bead breaking force of up to 3.8 t, accommodation of rim flanges of up to 40 mm thick, control console with switch for simultaneous control of two functions, automatic operation of mounting tool and preset tool carriage travel.Radio controlled operation.MONTY®4400TRUCK TIRE CHANGERHIGH VOLUMEPRODUCT DESCRIPTIONRugged chuck design,double reinforced frameallowing to handle wheels ofup to 1500 kg, control unitwith switch to control twooperations simultaneously, 2chuck speedsMONTY®3850TRUCK TIRE CHANGERHIGH VOLUMEPRODUCT DESCRIPTIONElectro-hydraulic drive,mobile control unit, beadbreaker roll andmounting/demounting toolfitted on swing arm, safetyvalve on chuck preventsaccidental unclamping ofwheels.MONTY®3650TRUCK TIRE CHANGERGENERAL REPAIRPRODUCT DESCRIPTIONAccess ramp for easy loading of thetire changer, two rollers for beadbreaking and tire changing allowquick operation, easy control viaintegrated control console,clamping of wheel by its center borevia cone and wing nut.GEODYNA®980LHeavy-Duty Wheel BalancerThegeodyna®980L heavy-duty wheelbalancing system is designed to handlethe balancing needs of trucks, buses,RV’s, and Light Truck/Automobile tires.The geodyna®980L is equipped tohandle from the smallest of wheels, 12"(30.5 cm) to heavy-duty 25" (63.5) and“super-singles”.GEOLINER 920Heavy-Duty Truck Aligner PREMIUMSERVICEWith the Hofmann®geoliner®920,checking wheel alignment on heavy-dutyvehicles is faster and easier than everbefore. Support for a wide range ofvehicles, the geoliner920 wheelalignment system can performalignments on everything from medium-duty trucks to mobile cranes.HD TRUCK PRODUCT LINEASK ME FOR A PRIVATE PRODUCT VIEWING。

Snap-On Tools 电动抬高搬运平台说明书

MODEL # EELR319ASnap-On Tools CorporationTABLE OF CONTENTSITEM PAGE1.SAFETY AND OPERATING INSTRUCTIONS (3)2.GENERAL SPECIFICATIONS (5)3.CONTENTS (6)4.INSTALLATION REQUIREMENTS AND TOOLS (6)5.INSTALLATION INSTRUCTIONS (7)5.1UNPACKING PROCEDURE (7)5.2HYDRAULIC SYSTEM INSTALLATION (7)5.3HYDRAULIC SYSTEM BLEEDING PROCEDURE (7)5.4ANCHORING PROCEDURE (8)6.POSITIONING INSTRUCTIONS (8)7.OPERATING INSTRUCTIONS (9)8.RECOMMENDED MAINTENANCE (9)8.1DAILY MAINTENANCE (9)8.2MONTHLY MAINTENANCE (9)9.MAIN FRAME ASSEMBLY (11)9.1MAIN FRAME ASSEMBLY - PARTS LIST (12)9.2HYDRAULIC CYLINDER ASSEMBLY (13)9.3HYDRAULIC CYLINDER ASSEMBLY - PARTS LIST (14)9.4PULL-OUT PAN ASSEMBLY (14)9.5PULL-OUT PAN ASSEMBLY - PARTS LIST (14)9.6POWER PACK STAND (15)9.7POWER PACK STAND - PARTS LIST (16)9.8POWER PACK: #6-2249 (AB-1425) 115-230V/1PH/60Hz (17)9.10POWER PACK PARTS LIST: #6-2249 (AB-1425) 115-230V/1PH/60Hz.181. SAFETY AND OPERATING INSTRUCTIONS1. Read all safety and operating instructions before using the lift.2. Inspect the lift daily. Do not operate the lift if it is damaged, malfunctioning, or ifproblems have been encountered.3. Never attempt to overload the lift. The manufacturer’s rated capacity is shown on theserial number tag, located on the scissor assembly.4. DO NOT OVERIDE the automatic safety devices incorporated into the lift.5. Only trained and authorized personnel should operate the lift. Do not allowcustomers or bystanders to operate the lift or be in the lift area. Operators andbystanders must stay completely clear of the lift when raising and lowering.6. The lift must only be operated on level and smooth floors.7. Never drive a vehicle into position on the lift. All vehicles must be pushed onto thelift. Before rolling a vehicle on or off the lift, make certain that the lift has beencompletely lowered.NOTE: When positioning a vehicle on the lift, take time to center the load front-to-rear and side-to-side. The removal or installation of some vehicle parts maycause a critical shift in the center of gravity and may cause the vehicle tobecomeunstable.8. All vehicles must be securely fastened to the lift using tie down straps. Anappropriate tie down kit is available through SNAP-ON dealers (EELR319ATDK).9. To raise the lift, press the “UP” button on the front face of the powerpack motor. Tolower, raise the lift until the automatic safety release device trips, then press down on the control lever.10. Do all work while the lift is on its mechanical safety lock.11. Always keep the lift area free of obstruction and debris. Grease and oil spills shouldalways be cleaned up immediately.12. Never raise the lift with a passenger onboard. Do not climb onto the lift or vehiclewhen it is in the raised position.13. Retract the approach ramp after the lift has been raised to avoid any sharp, protrudingobjects.14. Avoid excessive rocking of the lift while it is in the raised position.15. Before lowering the lift, check the area for obstructions.16. Care must be taken as burns can occur from touching hot parts.17. Do not operate equipment with a damaged cord, or if the equipment has been droppedor damaged – until a qualified serviceman has examined it.18. Do not let cord hang over table, bench or counter or come into contact with hotmanifolds or moving fan blades.19. If an extension cord is necessary, a cord with a current rating of two times or morethan that of the equipment should be used. Cords rated for less current than theequipment may overheat. Care must be taken to arrange the cord so that it will not be tripped over, or pulled.20. Always unplug equipment from electrical outlet when not in use. Never use the cordto pull the plug from the outlet. Grasp and pull plug to disconnect.NOTE: DO NOT ATTEMPT TO OPERATE THE LIFT IF ANY PART IS NOT WORKING PROPERLY OR IF YOU HAVE NOT READ THE COMPLETE OPERATING INSTRUCTION MANUAL.2. GENERAL SPECIFICATIONS680kg Capacity: 1500lbs.Overall Width: 27” 686mmOverall Width (with Opt. Side Extension Kit): 51” 1295mmOverall Width (with Opt. Portable Kit): 48” 1219mmOverall Length: 89” 2261mmOverall Length (with Opt. Side Extension Kit): 112” 2845mmOverall Length (with Opt. Front Extension Kit): 101” 2565mmDown Position Height: 6” 152mmMaximum Lifting Height: 48” 1219mmShipping Weight: 250lbs. 113kgPower Requirement 115V, 20Amp, 1Ph., 60HzLifting Time: 15 sec.3. CONTENTSThe complete Desperado lift is contained in two (2) packages:1. The main structural components are packed on a shipping skid.2. The remaining parts are packed in an accessory box.Main Structural Components include:1pc. Deck-Scissor Assembly (including Pull-Out Pan and Approach Ramp) Accessory Box Contents:1pc. Power Pack Stand (with Power Pack)1pc. “Posi-Grip” Wheel Locator1pc. 12' Hydraulic Hose1pc. Owner's Manual2pc. Wedge Anchor, ½”DIA x 4 ½”LG. (c/w nuts and washers)2pc. Carriage Bolt, ½”DIA x 5”LG.4pc. Hex Nut, ½”DIA4. INSTALLATION REQUIREMENTS AND TOOLSNOTE: Lifts should only be installed on “level” concrete floors, with a minimum thickness of five (5) inches or 130mm. Concrete must have a minimum strength of 4000psi or 30 MPa and should be aged thirty (30) days prior to installation. Please consult the architect, contractor or engineer if doubt exists as to the strength and feasibility of the floor to enable proper lift installation and operationTools Required:1. 1/2” wrench2. 9/16” wrench3. 3/4” wrench4. 5/16” wrench5. Rotary Hammer Drill6. ½” Diameter Masonry Drill Bit5. INSTALLATION INSTRUCTIONS5.1 UNPACKING PROCEDURERemove the metal strapping from the main structure package and slide the lift off the shipping skid. Open the accessory box and check the contents of the box.NOTE: The Power Pack is already installed on the Power Pack Stand5.2 HYDRAULIC SYSTEM INSTALLATION1. Add 3 litres of ISO 32 (10 Hydraulic Weight) hydraulic oil to the power pack.2. Reinstall the filler breather cap onto the power pack.3. Plug the power pack utility cord into an approved 115 Volt outlet.4. Install the 1/4” JIC female end of the 12’ long hydraulic hose to the outlet fitting onthe hydraulic cylinder.5. Connect the other end (3/8"JIC female) of the 12' long hydraulic hose to the 90°fitting on the power pack.5.3 HYDRAULIC SYSTEM BLEEDING PROCEDURENOTE: Make certain lift area is clear from debris and any obstructions.1. Press the “UP” button on the power pack and raise the lift a few inches off the floor.Check for any hydraulic leaks.2. Lower the lift by pushing the down control lever on the power pack.3. Lower the lift completely.4. Repeat this procedure to bleed the hydraulic cylinder.5. Raise the lift to engage the mechanical safety lock.6. Lower the lift onto the safety.7. Raise the lift a few inches to automatically disengage the mechanical safety.8. Lower the lift completely.9. Cycle the lift up and down completely a few times.10. The hydraulic system is a self bleeding system.5.4 ANCHORING PROCEDURENOTE: The lift must always be anchored to a level and smooth floor. If the lift is to be operated in different locations, a portable kit, that includes a tow cart and outrigger, must be used. A portable kit (EELR319APKT) can be purchased from your SNAP-ON dealer. Note:When the tow cart is used, the lift must be in the fully down position and vehicles must be removed from the lift.1. Position the lift in the center of the work area or bay to ensure adequate clearancearound the lift. To move the lift, raise the rear end off the ground and roll it intoposition. Place the power pack stand in a suitable area.2. Raise the lift to its full height and lower it onto its safety.3. Using a rotary hammer with a ½” masonry drill bit, drill two holes in the floorthrough the holes in the base angle weldment (see parts list).4. Install the anchor bolts and torque them to 150 ft⋅lb.5. Install the ½”DIA x 5” carriage bolts under the rear of the deck (left and right of thepull-out pan). Adjust the bolts so that the deck is level when fully collapsed.6. POSITIONING INSTRUCTIONSNOTE: Please review the safety instructions and the safety card attached to the stand.Inspect the lift for mechanical fitness before using.1. Plug the electric utility cord into an approved 115V outlet.2. Pull out the approach ramp from the pull-out pan and lower onto the ground.3. Roll the vehicle onto the lift. Vehicles must never be driven onto the lift.4. Using tie down straps, secure the vehicle to the lift.NOTE: When positioning the motorcycle on the lift, take time to equalize the load front-to-rear and side-to-side. Some vehicles may require additional assistance whenloading and unloading. Always restrain vehicle to lift using proper tie downstraps.7. OPERATING INSTRUCTIONS1. Raise the lift by pressing the “UP” button on the front face of the Power Pack Motor.2. Continue raising the lift until the mechanical safety “CLICKS” into position. Alwayslower the lift to fully engage the mechanical safety lock.NOTE: All lifts are equipped with dual safety locking devices, an automatic mechanical safety bar, and a flow control to protect against hydraulic failure.3. To disengage the mechanical safety and lower the lift, press the “UP” button on thePower Pack Motor to raise the lift off of the mechanical safety. Continue raising the lift until the automatic mechanical safety release device trips.4. Lower the lift fully to the down position.5. Roll the vehicle straight back off the lift.8. RECOMMENDED MAINTENANCE8.1 DAILY MAINTENANCE1. Check the general operation of the lift.2. Check the operation of the automatic mechanical safety lock, both engaging anddisengaging.3. Check the floor condition in the roller area for cracks and debris.4. Check the position of the hydraulic hose, ensure that a motorcycle positioned on thelift or the lift itself will not damage the hose.5. Check the condition of the electrical cord before plugging the power pack into anapproved 115V power supply.8.2 MONTHLY MAINTENANCE1. Check all hydraulic hoses, fittings and cylinder for leaks.2. Check the level of oil in the power pack reservoir when the lift is in the loweredposition. Add more hydraulic oil (ISO 32) if required.3. Check and grease all hinge points.4. Check and lubricate the automatic safety release device.5. Inspect the 115V plug end and cable.6. Inspect the main structure of the power pack stand.7. Inspect the lift area for debris and concrete condition9. MAIN FRAME ASSEMBLY9.1 MAIN FRAME ASSEMBLY - PARTS LISTITEM NO.QTY.DESCRIPTION PART NO.WELDMENT4-0615 DECK1 12 1 PULL-OUT PAN ASSEMBLY3-06683 1 PULL-OUT PAN RAMP WELDMENT3-06724 1 INNER SCISSOR WELDMENT4-06185 12WASHER, 3/4" SAE6-0738FLATBUSHING6-1687 6 4BRONZECASTING1-1664 ROLLER7 2ROLLERPIN1-1665 8 6PIN, 3/16" X 1 1/4" LG.6-07499 12SPRING10 1 OUTER SCISSOR WELDMENT4-0619SCREW, 1/4"-20UNC X 3/8" LG. 6-058011 4 SETWASHER, 1" SAE6-032812 4 THRUST13 8 BUSHING6-3105PIN, 3/16" X 1 1/2" LG.6-168214 4 SPRINGPIN1-166015 2 SCISSOR16 2 DECK GLIDE BLOCKS1-1673BOLT, 3/8" X 3/4" LG.6-072917 2 SHOULDER18 1 LOWER BASE ANGLE WELDMENT3-0660GROMMET6-0670 19 1 RUBBERASSEMBLY3-0667 20 1 CYLINDER(LOWER)2-1330AXLE21 1 CYLINDER(UPPER)2-132922 2 CYLINDERAXLE23 1 BRAKE LEG WELDMENT3-0663(NYLON)2-081924 1 OVERRIDEPLATEPIN, 1/4" X 1 1/2" LG.6-074525 1 SPRINGBOLTS, 1/2"-13UNC X 4 1/2"LG6-014026 2 ANCHOR27 2 FLATWASHER, 1/2" SAE6-0248NUT, 1/2"-13 UNC6-003528 2 HEXTAG6-166329 1 SERIAL30 1 "POSI-GRIP" WHEEL LOCATOR3-069231 1 HYDRAULICHOSE, 12FT LONG6-231932 1 FLOW CONTROL 0.75MM6-16389.2 HYDRAULIC CYLINDER ASSEMBLY9.3 HYDRAULIC CYLINDER ASSEMBLY - PARTS LISTITEM NO. QTY. DESCRIPTION PART NO.1 1 CYLINDER TUBE WELDMENT2-13232 1 PISTON ROD WELDMENT2-1324GLAND 1-16693 14 1 WEAR RING 1 3/8”ID x 1 1/2”OD x 3/8”LG 6-16795 1(2” BORE)2-0511PISTON6 3 ALLEN HD SET SCREW 1/4”-20UNC x 3/8”LG 6-05807 1 SEAL AND WEAR RING6-0579KEEPERWASHER1-07258 19 1 EXTERNAL SNAP RING6-05819.4 PULL-OUT PAN ASSEMBLY9.5 PULL-OUT PAN ASSEMBLY - PARTS LISTITEM NO. QTY. DESCRIPTION PART NO.1 1 PULL-OUT PAN WELDMENT2-13262 2 PULL-OUT PAN GLIDE BLOCKS (FRONT)1-16743 2 PULL-OUT PAN GLIDE BLOCKS (REAR)1-16754 4 SHOULDER BOLT 3/8” x 5/8”LG6-00695 4 HEX NUT 5/16”6-02945/16”6-0674 6 4LOCKWASHER7 4 #10 SELF TAPPING SCREW, 3/4”LG6-02979.6 POWER PACK STAND12510 6789119.7 POWER PACK STAND - PARTS LISTITEM NO.QTY.DESCRIPTION PART NO.1 1 STAND WELDMENT BLACK (WITH WHEELS & HUB) 4-0207-012 4” DIA PLASTIC WHEEL6-0753HUBCAPNUT6-1833 22 1ELBOW 90°¼” JIC TO 9/16” SAE6-10933 1 POWER PACK 115V 3/4 HP*6-2249HANDLE6-0758 GRIP4 1PLUG 6-14885 16 4 HEX BOLT 1/4"-20UNC 6-00287 4 LOCKWASHER 1/4" I.D.6-00568 4 FLAT WASHER 5/16" I.D.6-02951/4-20UNC6-0032 NUT9 4PLACARD6-1831 10 1SAFETYELBOW6-109390°11 1WHEEL PLASTIC 4”6-0753* SEE NEXT PAGE FOR THE POWER PACK9.8 POWER PACK: #6-2249 (AB-1425) 115-230V/1PH/60Hz9.10 POWER PACK PARTS LIST: #6-2249 (AB-1425) 115-230V/1PH/60HzITEM QTY. DESCRIPTION PART # 1 2 BOLT 5/16”-24 x 2 ¾” TORX G8 6-2298 2 1 COUPLING SAE 9T-20/40 1.260” 6-0774 3 1 SEAL SHAFT 0.500” x 1.00” x 0.25” 6-2158 4 1 MOTOR AC PSC #613000 115/230 1 HP 1PH BLK 6-2299 5 1 WASHER 0.338” x 0.625” x 0.060” STEEL 6-2159 6 1 CORDSET 16/3 SJO 8FT 115V PLUG 6-2300 7 1 PACKAGE PLUG 9/16” SAE 6-2301 8 1 PLUMBING MAGNET 6-2162 9 1 RELIEF VALVE CAP ASSEMBLY 6-1089 10 1 PLUMBING CLAMP HOSE ADJ INLET 6-2166 11 2 ELECTRIC STAKON NUT 6-2302 12 1 COVER ASS’Y SUCTION 6-2165 13 2 SCREW TAPTITE M6x1.0 12MM TORX 6-2164 14 1 NAMEPLATE, SERIAL 15 1 ENDHEAD UNIVERSAL AUTOHOIST 6-2155 16 1 ELECTRIC CORD GRIP ¾” NPT 6-2303 17 1 ELECTRIC PIPENUT ¾” 6-2304 18 1 VALVE CARTRIDGE CHECK 6-1087 19 1 VALVE LOAD DELAY 6-2305 20 1 NUT ¾”-16 x 1”HEX x 0.250 STEEL 6-2167 21 1 WASAHER ¾” INT. TOOTH LOCK 6-2168 22 1 BRACKET HANDLE ASS’Y REL BLACK 6-0776 23 1 COMPRESSION TUBE NUT 6-2153 24 4 BOLT M6 x 1.0 35MM SOC HD 6-2169 25 4 WASHER ¼” LOCK HI-COLLAR 6-2170 26 4 BOLT #12-24 x .50 HEX WSHRHD 6-1091 27 1 O-RING 2-348 BUNA 6-0875 28 1 COVER ASSY SUCTION 6-2165 29 1 PUMP ASS’Y 0.8 SHORT SPLINE 6-2306 30 1 TANK PLASTIC 6.7 CT 11.0” BLACK 6-2307 31 1 SPRING 0.480” x 0.063” x 0.42” COMP 6-2151 32 1 PLUMBING PLUG 5/16” SAE 6-2157 33 1 CABLE TIE 8” LONG WHITE 6-1846 34 1 PLUMBING ASS’Y INLET 6.61 (3) 6-2308 35 1 VALVE CARTRIDGE RELEASE MANUAL 6-0880 36 1 RELIEF ASSEMBLY FIXED 240 BAR 6-2309 37 1 COMPRESSION TUBE SLEEVE 6-2154 38 1 RETURN HOSE 3/8” OD x 10.0” 6-2310 39 1 PLUMBING PLUG 3/8”NPT 6-2161 40 2 ELECTRIC REDUCER WASHER 6-2311 41 1 WIRING ASSEMBLY AC 1PH FENNER 6-2156 42 1 LABEL INSTALLATION AUTOHOIST 6-2136 43 1 BREATHER CAP & BLADDER 6-1376。

Snap-on MB车轮对齐器产品说明书

Parts ManualTEEWA553MB3Table of ContentsEEWA553MB1 - MB ALIGNER (2)CABINET-COMPLETE MB (3)CABINET (MB) (4)POWER BOX (6)KIT USB RADIO (8)CAM/CAM ASSEMBLY (9)CAM/TARGET ASSEMBLY (9)CAMERA PODS (CAM/CAM) (10)CAMERA PODS (CAM/TAR) (12)POD CAR (14)MOTOR / GEAR ASSEMBLY (15)BASE TOWER (16)ELECTRICAL MOUNT PLATE ASSY (17)BASE TOWER ASSY (18)WHEEL CLAMP (20)AC700 WHEEL CLAMP - XD TARGET, FRONT (22)AC700 WHEEL CLAMP - XD TARGET, REAR (23)NOTE:Items Marked in RED are used in EuropeItems marked in BLUE are used in North AmericaAll items marked in BLACK are common parts2Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.T E E W A 553M B 3 - S P A R E P A R T SREQ PART NUMBER DESCRIPTION1 EAK0268J05A PRINTER KIT - USB1 88931POWER CORD / LABEL ASM 1 EAK0277J82A LITERATURE PACK GENERIC 1 EAL0343J76A LABEL - SERIAL1 96 DEPRESSOR ASSY . PEDAL 1 55502STEERING WHEEL HOLDER1 EAK0320J70A KIT – MONITOR 27” LCD W/ CABLE 1 EAK0320J56A HANGER BRACKETS-MULTI CLAMP2 EAC0090J82A WHEEL CHOCK RUBBER1 5403INSTALLATION REGISTRATION CERTIFICATE 1 EAK0289J23A KIT REMOTE CONTROL1 EAS2164V11A SUPPORT BRACKET MONITOR 8 1-16006A SCREW - M5 X 12 MM PH BLK 4 1103959000 WASHER - FLAT M51 EAK0334J17A KIT, V3400MB DECALS1 EAK0334J18A KIT, GEOLINER 790MB DECALS 1 TEEWA553MB0 INSTALLATION INSTRUCTIONS 1 ZEEWA550AMB OPERATOR'S MANUAL 1 EAK0320J60A KIT-AC700 FT, XD 6X8, NA EAK0320J73A KIT-AC700, FT XD 6X8, EU 1 EAK0320J61A KIT-AC700 RR, XD 6X8, NA EAK0320J74A KIT-AC700, RR XD 6X8, EU 1 EAA0429J75A CABINET-COMPLETE MB 1 EAA0429J75B CABINET-COMPLETE MB, EU 1 EAA0381J52C V3400 OEM TOP LEVEL ASM. EAA0381J81C V3400 OEM TOP LEVEL ASM 1 EAK0256J71A RIDE HEIGHT MEASUREING KIT 1 ZEEWH612A1 INST’R – EQUIPMENT DISPOSAL 5 5-2345 CABLE TIE5 5-06945A MOUNT, CABLE TIE1 88690CONTROL – REMOTE, JBC ASSY 2 EAK0277J26A SHIM KIT – 1,0 MM 1 EAK0305J42A KIT, TURNTABLE, MB1AWM6DHEX WRENCH, 6MM L-SHAPEEEWA553MB1 - MB ALIGNER EEWA753MB1 - MB ALIGNER John Bean HofmannCABINET-COMPLETE MBEAA0429J75A - NAEAA0429J75B - EUREQ PART NUMBER DESCRIPTION1 EAA0422V01A CABINET,HE MB GRAY1 EAA0429J76A EMBED PC, PRO42, MB - NA1 EAA0429J76B EMBED PC, PRO42, MB - EU1 5-11026A NYLON STRAP1 1-21484A SCREW, 10-32X1/”, SLOTTED GREEN GROUND1 EAW0235J36A CABLE, 12” GROUND1 1-13633A NUT, BARB, EXT. WASHER, M51 EAP0238J54A PCB ASSY., USB, IR2 1-04084A STANDOFF – NYLON2 1-13533A NUT – BARB, M41 EAL0343J22A WINDOW-REMOTE1 8-08116A BUSHING-SNAP 16/16ID,29/64LG1 EAK0305J36A KIT – USB RADIO - CAB1 2-02639A BLUETOOTH RADIO – USB5 2-09033A CLIP, CABLE, 0.2-0.3” DIA CABLE1 111243 LABEL-WARNING,EXPLOSION1 EAL0392J18A LABEL-PATENT ALIGNMENT1 2-05039A POWER DISTRIBUTION UNIT, IEC C14 4 OUTLETS2 EAW0290J28A POWER CORD, IEC C14, 20FT1 88635 ADAPTOR, POWER, C14 1FT5” 5-10426A1 VELCRO, HOOK SIDE5” 5-10426A2 VELCRO, LOOP1 2-09457 CABLE CLAMP1 1-03382A CABLE CLAMP, 1/21 1-16006A SCREW, M5X12MM2 5-03945B CABLE TIE MOUNT, 1”X1”, BLACK2 4500-0029 CABLE TIE, BLACK TEEWA553MB3 - SPARE PARTS3Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.4Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.T E E W A 553M B 3 - S P A R E P A R T SCABINET (MB)EAA0422V01A - GRAY3 4 61415161718212223252728291257910111920242630313233EAC0116J55A - BOTTOM BRKTEAC0116J54A - TOP BRKT5Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.TEEWA553MB3 - SPARE PARTSEAK0320J56A - HANGER BRACKETS - MULTI CLAMPREQ PART NUMBER DESCRIPTION2 EAC0116J54A CLAMP HOLDER, UPPER 2 EAC0116J55A CLAMP HOLDER, LOWER24 1-39506ASCREW – PHMS, M8 X 1.25MM X 16MM 1TEAK0320J56AINSTALLATION INSTRUCTIONSSYM REQ PART NO DESCRIPTION1 4 1-13606A SCREW,PH,M4X6MM,ZN2 5 1-16006A SCREW,PH,M5X12MM,BLK34 1-25306A SCREW,PHMS,M5X20MM 4 4 1-38909A SCREW,BHCS,M4X12MM5 8 1-55501A SCREW, HEX 5/16"-12X1"6 4 1-5665 BUSHING - SHOULDER7 2 8-33939A CASTER-SWIVEL, 5" WITH BRAKE 9 2 8-33939BCASTER-SWIVEL, 5" W/O BRAKE 10 1 EAA0416V07B BACK PLATE ASSY ,STD ME-HE 11 1 EAA0416V23B BASE ASSY ,ME-HE,EXTENDED 12 4 5-03945B CABLE TIE MOUNT,1"X1",BLACK 13 4 4500-0029 CABLE TIE,BLACK 14 2 EAC0116J56A CAP ,CORNER TRIM15 2 EAC0121V06A CORNER TRIM,ARC SHAPE 16 1 EAA0422V05A DOOR ASSY ,PC,GRAY RAL701517 1 EAA0422V04A DOOR ASSY ,PRINTER,GRAY RAL701518 5 EAC0121V05A DOOR TRIM, FRONT19 1 EAA0416V14A DRAWER ASSY ,PRINTER 20 2 EAC0121V09A INSERT,PRINTER DOOR21 1 EAA0422V02A LEFT PANEL ASSY ,GRAY RAL701522 4 8-04842A MAGNET,NDFEB,NI PLATED 23 4 1-11233NUT,HEX,M324 1 EAA0422V03A RIGHT PANEL ASSY ,GRAY RAL701525 8 1-17358 RIVET,AL,4MM,SILVER 26 62 1-15158A RIVET,STEEL,4.8MM,BLK 27 4 1-11103CN SCREW,FH,M3X10MM28 1 EAA0422V06A SHELF ASSY ,PRINTER,GRAY RAL7015 29 1 EAS2164V16A SHELF,PC,ME-HE-SHE 30 1 8-06488ASLIDE TRAIL31 2 EAS2164V07A SUPPORT BRACKET,PC-IN-BOX 32 1 EAA0416V01A TOP PANEL ASSY ,ME-HE33 1 8-09816A GROMMET-BLACK.25 ID X 1.00 OD6Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.T E E W A 553M B 3 - S P A R E P A R T SPOWER BOX14678911121314151719202122232427293031323334 35362351016 1826EAA0416V36PW - NA (3 CAMERA SERVICE EMBEDDED PC)EAA0420J58A - EU (3 CAMERA SERVICE EMBEDDED PC)SYM REQD PART NO DESCRIPTION1 1 86465 LABEL-WARNING,SHOCK HAZARD2 1 111245 LABEL-CAUTION,ELECTRICAL3 2 1-2376 HOLE PLUG4 3 1-3347 LOCKWASHER,INTERNAL TOOTH5 2 1-18206 SCREW M3X12,PAN HD,BLK6 2 1-15033 BARB NUT M37 4 1-14388A STAND OFF,M3X10MM8 2 1-13633A BARB NUT M59 3 1-27406A SCREW - PHM, M3 X 10MM10 1 2-14258A SWITCH, PC IN BOX11 2 2-31001A TERMINAL -QUICK CONNECT12 1 2-64448A IEC 320-C14 AC RECEPTACLE13 1 2-73166A ADAPTOR, 12V14 1 2-73466A RESET SWITCH15 2 8-23762A LABEL-EARTH SYMBOL16 1 EAA0261P60B IEC OUTLET17 1 8-20263A SOFTWARE-WES7,E EDITION18 1 EAL0415J15A LABEL-ELECTRICAL RATING19 1 EAL0415J44A DECAL,ON OFF SWITCH20 1 EAS2105J96B COVER - OUTLET21 1 EAW0235J74A CORD - POWER,PC IN BOX22 1 EAW0243P22B LINK WIRE,BROWN23 1 EAW0243P23B LINK WIRE,BLUE24 1 EAW0243P25B LINK WIRE,GRN/YEL25 4 5-2345 CABLE TIE26 1 EAA0416V05A MAIN CASE ASSY PC-IN-BOX27 1 2-81566A MOTHER BOARD WITH POWER CABLE28 4 5-06945A MOUNT,CABLE TIE29 1 2-81666A MSATA SSD, 128GB30 1 2-81466A RAM,4GB31 1 1-32606A SCREW, PAN HEAD, M2X4MM32 1 6-13122A USB CONNECTOR 4 PORTS33 2 5-14526A VELCRO HOOK,LAPTOP ADAPTOR HOLDER34 2 5-14426A VELCRO LOOP,LAPTOP ADAPTOR HOLDER35 4 1-11004A SCREW - PHM, M3 X 6MM36 1 5-11740B EMI GROUNDING TAPE,LENGTH 75MMNS 1 2-66466A1 FERRITE, TOROID EU TEEWA553MB3 - SPARE PARTS7Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.8Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.11Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your parts53M B 3 - S P A R E P A R T SCAMERA PODS (CAM/CAM)91112141516123456781013EAA0381J30C - NA EAA0381J82B1 - EU2017181911Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your parts53M B 3 - S P A R E P A R T S234 5671112131415171891016CAMERA PODS (CAM/TAR)EAA0381J31C - NA EAA0381J83B1 - EUSYM REQ PART NO DESCRIPTION1 3 1-07424A SCREW - PAN HD, 8-18 X 1/22 2 1-12724A SCREW - #6-19 X 1/4 SELF TAP - TRI3 2 1-12824A SCREW - #6-19 X 1/2 SELF TAP - TRI4 4 1-13204A2 SCREW - PHM, M4 X 10MM X 12MM5 8 1-18206 SCREW - PHM, M3 X 12M W/ WASHER6 4 1-5547 WASHER-LOCK, EXT, M47 2 5-2345 TIE - CABLE 4" LG X .10" WD8 1 8-09919A STRAIN RELIEF9 1 EAA0381J27A POD ASSY - V3D3, COMMON10 1 EAA0381J29B CAM-TAR ASM - V3400, OEM11 1 EAC0116J08A COVER - V3D3, SOLID12 1 EAC0116J12A COVER - V3D3, FRONT13 1 EAC0116J13A COVER - V3D3, VOD14 1 EAA0395J75A COVER - TOP, 6X815 1 EAA0395J74A COVER - BOTTOM, 6X816 1 EAL0343J76A ELECT/SERIAL LABEL17 1 EAL0343J81A GRAPHIC FACE PLATE - V3D218 1 EAW0235J48A CABLE ASS'Y, ULTRA MOTOR CABLE19 1 EAW0235J51A CABLE ASSY-CAMERA, ULTRA ARAGO20 1 EAW0235J82A CABLE - POWER, COILED V3D321 1 EAW0235J87A CABLE ASM - V3D3, COMM. TEEWA553MB3 - SPARE PARTS13Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your parts53M B 3 - S P A R E P A R T SPOD CAREAA0381J27A12345678910SYM REQ PART NO DESCRIPTION1 3 1-1548 WASHER-EXT,SHAKEPROOF 6MM2 8 1-16341A WASHER - FLAT (3MM), 9MM OD3 8 1-20504A SCREW PAN HEAD4 4 1-38606A MSCR PHIL PH W/LK M3X6MM5 3 1-47909ASCREW-HEX SOCKET H.CAP 6 1 EAA0381J32A MOTOR/GEAR ASM., V3D37 6 EAC0116J05A ROLLER - V3D38 6 EAM0088J16A PIN - ROLLER, 3MM9 1 EAM0088J20A SLIDE CAR - V3D3, MACHINE ASSY 10 1 EAP0280J30A CONTROL BOARD V3D315Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsTEEWA553MB3 - SPARE PARTS1235789101213BBMOTOR / GEAR ASSEMBLYEAA0381J32A REV BSYM REQ PART NO DESCRIPTION1 1 1-02863A BEARING- FLANGE MTD2 2 1-32806A SCREW - PHMS #10-24 X 3/83 4 1-347#10 INTERNAL TOOTH LOCKWASHER 4 1 EAM0088J31A SCREW-SHCS, 1/4-20 X 3/4,5 4 1-4806 MSCR PNH #10-32 X 1-3/46 1 1-7433 NUT & L/WASHER ASSY , 1/4-207 2 1-7733 LOCK NUT-10-24 X .3758 1 2-44066AGEAR MOTOR, 12V, ULTRA9 1 EAA0321J63A PLATE ASM. - MOTOR LOCK, UA 10 1 EAC0079J65A GEAR - SPUR, DIE CAST 12 1 EAS2119J83A BRACKET - MOTOR, V3D31321-12944ASPACER - .PULLY .62 OD X .13 LG53MB3-SPAREPARTS BASE TOWEREAA0381J38C12356101213 151617181920792122SYM REQ PART NO DESCRIPTION1 6 1-01637A NUT-ESNA,M62 2 1-04082A CLAMP - HOSE CUSHIONED3 8 1-12624A SCREW - THREAD FORMING, M4X.07,4 1 1-13533A NUT - BARB, M45 4 1-16641A WASHER - FLAT (6MM)6 2 1-16709 SCREW - SHCS, SCREW - SHC, M6 X 35MM7 1 1-16941A WASHER, LARGE ISO 7093 (DIN 9021)8 1 1-32641A WASHER-LOCK,M4 DIN 6797 TYPE A9 1 1-34201A MSCR, HEX HD - M10 X 16MM10 4 1-56001A BOLT - HEX HEAD, DIN93111 1 2-69966A POWER CABLE - RIGHT ANGLE12 2 8-08018A RUBBER FOOT13 1 EAA0381J37A ELECTRICAL MOUNT PLATE ASM14 1 EAA0381J70A TAG-TORQUE SPEC,V340015 1 EAA0395J28A WELD ASM- V3400 SHORT16 1 EAC0116J14A CLAMP - ALIGNER POLE, SIDE A17 1 EAC0116J15A CLAMSHELL-ALIGNER POLE,SIDE B18 1 EAL0343J76A ELECT/SERIAL LABEL19 2 EAL0392J07A LABEL- WARNING20 1 EAL0392J18A LABEL-PATENT ALIGNMENT21 1 EAL0392J19A LABEL-GROUND22 1 EAS2119J92B PLATE - DOUBLER, 5 DEG ROTATIONDETAIL ASTACKING OF GROUNDING CABLESPart numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your parts53M B 3 - S P A R E P A R T S479362581BASE / TOWER ASSYSYM REQ PART NODESCRIPTION 9 1 EAC0116J17A CAP - TOP , V3D3 8 1 EAA0381J38C BASE MOUNT ASM 7 1 EAA0381J33B RACK TOWER ASSY 6 4 8-08018A RUBBER FOOT5 4 1-37306A SCREW - PHM, M3 X 16MM4 1 1-26384A CABLE - LANDYARD, MANAGEMENT 3 3 1-12524A SCREW - M4 X 12MM, SELF TAP 2 4 1-11233 NUT,HEX,M31 1 1-07767A SPRING - CABLE MANAGEMENTEAA0381J51C EAA0395J35CTEEWA553MB3 - SPARE PARTS19Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.20Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.T E E W A 5 5 3 M B 3 -S P A R E P A R T S2 3459121315171819202223242511166814WHEEL CLAMPEAC0079J70A - WHEEL CLAMP ASSY- NA NO SHAFT EAC0079J76A - WHEEL CLAMP ASSY- EU NO SHAFTSYM REQ PART NO DESCRIPTION231-14144A WASHER-FLAT, M6381-17677A RETAINING RING411-20733A NUT - JAM, M8541-28103A MSCR, PH FLH M4 X 25MM611-3447M6 LOCKWASHER, INTERNAL TOOTH831-50309A SCREW-BHCS M6X10MM911-6152PIN-STRAIGHT SLOTTED M4 X 20MM112EAC0079J48A BRACKET-LONG WHEEL CLAMP (FRONT)122EAC0079J50A COVER-FEED SCREW LOCK132EAC0079J51A PLUG - PLASTIC, 19MM HOLE142EAC0079J52A WASHER-THRUST PLASTIC PLASTIC, 19MM HOLE151EAC0079J53A CENTER SLIDE BRACKET161EAM0044J13A KNOB HAND WHEEL172EAM0044J14A TUBE-WHEEL CLAMP LONG (NA)EAM0044J64A TUBE-WHEEL CLAMP SHORT (EU)181EAM0044J16A SCREW-DOUBLE LEAD LONG (NA)1EAM0044J65A SCREW-DOUBLE LEAD SHORT (EU)194EAM0044J19C GRABBER ASM, SINGLE END201EAM0044J20A BUSHING-THREADED BRASS RH222EAM0044J22A PIN-TUBE LOCK231EAM0044J24A BUSHING THREADED BRASS LHEAM0044J20A BUSHING THREADED BRASS RH241EAM0044J47A SCREW - SHCS M8X30 FULL THD252EAS2084J29A PLATE-RETAINERPART NUMBER DESCRIPTION1-08584A CORD – BUNGEE, BLACK 16”EAK0268J41B GRABBER KIT – DUAL ENDEAC0105J35A COVER-RUBBER, V3D TEEWA553MB3 - SPARE PARTS21Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.22Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.T E E W A 553M B 3 - S P A R E P A R T SAC700 WHEEL CLAMP - XD TARGET, FRONT123456 SYM REQ PART NO DESCRIPTION 1 1 1-08584ABUNGEE CORD2 1 EAA0420J12A TARGET ASM - 6X8 XD PIN, FT LH, OEM 1 EAA0420J13A TARGET ASM - 6X8 XD PIN, FT RH, OEM3 1 EAC0079J76A WHEEL CLAMP IMAGE FT, NO SHAFT, EU 1 EAC0079J70A WHEEL CLAMP IMAGE FT, NO SHAFT, NA4 4 EAC0105J35A COVER - RUBBER, V3D5 1 EAK0268J41C GRABBER KIT - SINGLE END6 1 EAL0415J09A DECAL - LEFT FRONT, INDICATOR 1 EAL0415J12A DECAL - RIGHT FRONT, INDICATOR12 368910SYM REQ PART NO DESCRIPTION 1 2 1-20733A NUT - JAM, M82 2 1-38806A SCREW - M5 X 16MM W/ WASHER3 2 1-54810A SCREW - SET. M8 X 20MM, CONE PT4 1 8-10632AADHESIVE - DP5106 2 PART EXPOXY 6 1 EAC0116J00A HANDLE - TARGET, SUPPORT8 1 EAL0415J09A DECAL - LEFT FRONT, INDICATOR 1 EAL0415J12A DECAL - RIGHT FRONT, INDICATOR 9 1 EAM0088J56A ADAPTOR 3.5" - XD TARGET - OEM 10 1 EAS2119J98A PLATE - SUPPORT, HANDLE23Part numbers and descriptions are for reference purposes only. Not all parts shown are stocked as service parts, consult your partsdepot warehouse for availability.TEEWA553MB3 - SPARE PARTS123456 SYM REQ PART NO DESCRIPTION 1 1 1-08584ABUNGEE CORD2 1 EAA0420J14A TARGET ASM - 6X8 XD PIN, LR RH, OEM 1 EAA0420J15A TARGET ASM - 6X8 XD PIN, RR RH, OEM3 1 EAC0079J76A WHEEL CLAMP IMAGE FT, NO SHAFT, EU 1 EAC0079J70A WHEEL CLAMP IMAGE FT, NO SHAFT, NA4 4 EAC0105J35A COVER - RUBBER, V3D5 1 EAK0268J41C GRABBER KIT - SINGLE END6 1 EAL0415J11A DECAL - RIGHT REAR, INDICATOR 1 EAL0415J10A DECAL - LEFT REAR, INDICATOR12389106SYM REQ PART NO DESCRIPTION 1 2 1-20733A NUT - JAM, M82 2 1-38806A SCREW - M5 X 16MM W/ WASHER3 2 1-54810A SCREW - SET. M8 X 20MM, CONE PT4 1 8-10632AADHESIVE - DP5106 2 PART EXPOXY 6 1 EAC0116J00A HANDLE - TARGET, SUPPORT 8 1 EAL0415J10A DECAL - LEFT REAR, INDICATOR 1 EAL0415J11A DECAL - RIGHT REAR, INDICATOR 9 1 EAM0088J24A ADAPTOR - XD TARGET - OEM 10 1 EAS2119J98A PLATE - SUPPORT, HANDLEAC700 WHEEL CLAMP - XD TARGET, REARNotice: The information contained in this document is subject to change without notice. Snapon makes no warranty with regard to this material. Snapon shall not be liable for errors contained herein or for incidental consequential damages in connection with furnishings, performance, or use of this material.This document contains proprietary information which is protected by copyright and patents. All rights are reserved. No part of this document may be photocopied, reproduced, or translated without prior written consent of Snapon.Snap-on309 Exchange Ave.Conway, AR 72032501-450-1500TEEWA553MB3 03/2017...rjh Printed in the U.S.A。

2023年扭矩扳手行业市场规模分析

2023年扭矩扳手行业市场规模分析扭矩扳手是一种用于紧固螺栓和螺母的手动工具，具有对螺栓和螺母进行精准扭矩控制的能力，常用于汽车、航空、机械制造等领域。

随着工业化和机械化的不断推进，扭矩扳手市场需求逐渐增加。

本文将对扭矩扳手行业市场规模进行分析。

一、市场规模根据市场研究机构的报告显示，全球扭矩扳手市场规模正在稳步增长。

截至2019年，全球扭矩扳手市场规模约为12.5亿美元。

预计到2025年，市场规模将达到16.5亿美元，年复合增长率为4.5%。

在地区分布方面，亚太地区是扭矩扳手市场最大的地区，2019年该地区市场份额约为38%。

其次是欧洲和北美，市场份额分别为32%和22%。

其他地区份额相对较小。

二、市场需求扭矩扳手应用范围广泛，主要用于汽车维修、机械制造、航空航天、轨道交通等领域，这些领域对高精度扭矩控制的需求不断增长。

随着中国制造业的不断升级和发展，国内扭矩扳手市场需求逐渐增加，2019年国内扭矩扳手市场规模约为2.4亿元，市场增长势头较好。

据预测，未来随着高端设备和智能制造的发展，国内扭矩扳手市场规模将会继续增长。

同时，全球航空航天、轨道交通等领域对扭矩扳手的需求也在逐年增加，这些高端客户对产品的质量和使用体验要求高，这与扭矩扳手高精度扭矩控制的特点相符，这是扭矩扳手未来市场需求的关键之一。

三、市场竞争全球扭矩扳手市场竞争激烈，主要厂商有Snap-on, Norbar, Gedore, Tohnichi, Stahlwille、STAHLWILLE。

这些厂商主要分布在欧美地区，其产品以高精度、高稳定性、高耐用性等特点受到用户青睐。

在国内市场上，虽然有一些生产扭矩扳手的企业，但是大部分企业规模和产能都比较小，且生产的产品质量有时存在一定的问题。

因此，国内扭矩扳手市场上，外资品牌和国内知名品牌更具竞争力。

四、发展趋势1、智能化趋势未来扭矩扳手产品将更加智能化，例如使用智能手机连接扭矩扳手，进行扭矩检测和数据分析，从而实现扭矩控制的数字化。

Snap-on Tools 车辆维修工具系统说明书

1
EAW0235J45A
*
1
EAW0235J46A
9
1
2-12258A
10 2
2-15651A
11 2
2-18451A
12 4
1-02007A
13 1
2-37348A
14 1
EAW0243P26A
15 1
8-09016A
16 1
EAA0261P60A
17 2
EAL0345P51A
18 1
EAW0243P25A
9
1
EAS2072J61A
10 1
EAS2072J65A
11 2
EAW0243P23A
12 2
EAW0243P22A
13 1
EAW0243P25A
14 2
2-18451A
15 1
EAW0243P26A
*
2
00088635000
16 4
1-02007A
*
2
1-9733
17 1
2-43166A1
18 2
Page 2
POWER SUPPLY HIGH END CABINET
EAA0305J65A
Ref Qty Req. Part Number
1
4
1-9833
2ห้องสมุดไป่ตู้
2
1-11103
3
2
1-29906A
4
1
2-12258A
5
2
2-15651A
6
1
2-37348A
7
2
2-31001A
8
1
EAA0261P60A

Snap-on 扭矩认证技术培训手册说明书

T ORQUE C ERTIFICATIONTorque technology programSnap-on Incorporated, in partnership with Gateway Technical College, has created a national torque certification program designed to meet the needs of the growing global wind industry.This program in torque technology will provide the student with hands-on learning to torque techniques, bolting applications, and tool set-up and selection concepts within today’s wind industry. Torque is the turning motion used to tighten or secure a fastener to achieve proper clamping force.Gateway program administrators continue to strive to ensure that the skills taught through the program are thorough and meet the needs of industry. The program, to be held on the Kenosha campus, will offer hands-on training that will guide the student from learning torque fundamentals and hand tool applications to advanced technology equipment to training on heavy-duty pneumatic and hydraulic equipment needed in today’s wind industry.Safe training and workplace techniques will be taught and stressed heavily at each level of training. Those completing all three training areas will learn many of the key skills needed to be employed in the wind turbine industry.Knowing torque applications is especially important in the wind industry because turbines, high in the air, need to withstand the rigors and stress put on them by the elements of cold, wind, rain and heat. Many wind industry careers will require certifications such as these to be considered for employment in this growing job field.The program will be split into three successive areas:Torque fundamentalsStudents will receive hands-on training in:•the process of torque and bolting and understanding how fasteners work•the science of torque•using torque measuring equipment•proper fastening and clamping force fundamentalsElectrical torqueStudents will build on the skills they learned in the fundamentals class, and expand that to receiving hands-on training in proper set up, use and maintenance of advanced electronic torque technology equipment.Torque IIIThe third area provides hands-on training to students in the big torque equipment used in today’s wind power industry. Students will be trained in today’s gear reduction multipliers as well as pneumatic and hydraulic-operated machines.For more information, on how you can become certified or to start a training program at your local college, contact Larry Hobbs at **************.Gateway is part of the Wind Energy Training Consortium, public/private partnership that shares a vested interest in advancing training and worker development initiatives in the wind-power industry.。

整车生产扭矩工具识别及使用

GM对于PS2/PF1点的要求
➢OPION-A：电缆枪（有扭矩传感器、自动报警停线、计数、有防重打功能）+100%互检(没有强制要求点漆，但互检工位的 SOS中需要有明确的检查方法） + 扭矩抽检
13
➢OPTION-B：动力工具紧固（断气式或离合式，精度在5%之内）+CLICK扳手（检查）（有扭矩传感器、计数、自动报警停线） +100%点漆(本工位）+ 100%互检(没有强制要求点漆，但互检工位的SOS中需要有明确的检查方法） + 扭矩抽检 ➢OPTION-C和OPTION-D与PS1点要求相同
生产线主要工具
对生产现场使用的起辅助作用的扳手不在此介绍，例如这就是我们一般都认识的活动扳手、呆扳手、梅花扳手、套筒扳手等。定扭工具主要有CLICK扳手、定扭电枪（BOSCH电枪）、ATLAS电枪及 ATLAS拧紧轴等。
CLICK扳手
生产线使用的click扳手主要有三种棘轮扳手、开口扳手和梅花扳手；具体如下：
GM对PF2点要求：
➢动力工具紧固（断气式或离合式，精度在5%之内）+目视（检查）+ 100%互检(没有强制要求点漆，但互检工位的SOS中需要有明确的检查方法） + 扭矩抽检
14
类型
PQC
扭矩衰减控制点设计要求
人机工程提升小扭矩控制点（所
有PQC点）
描述
PS1
PS2
PF1/PF2 Std.Care 软连接点角度控制内止外转 ≥65N•m ≤9N•m ≥9N•m≤15N•m
注：图中型号为 DB100N-S的指针扳手是指针式扳手中的一种，仅做参考
8
自动断气型油压脉冲风枪
已型号为PTF012-T6200-S10S

Snap-on 车辆对齐仪用户指南说明书

GENERAL OVERVIEW: _______________________________________________________ When a customer complains of crooked steering wheels or questionable alignment readings the problem is often not with the alignment machine. In general, the technician should assume that the alignment machine is correct until proven otherwise. The following list details items to be checked and verified prior to replacing parts or calibrating the unit. Each situation is different however we highly recommend that each of the steps listed in this guide be completed. It is highly possible to have more than one problem.ACTION TO BE TAKEN:_______________________________________________________ Items to check on the Alignment Machine1. Use your service vehicle to generate a complete set of alignment readings on a known good aligner. Printthe results for future reference. Update your service vehicle’s alignment readings on a regular basis.2. Use your service vehicle to generate a complete set of alignment readings on the suspect unit. Comparethe results to that of the known good unit as described in step 1. If the readings agree the problem is not likely to be with the alignment machine.3. Check that the wheel clamps are centering properly and that there are no loose, worn or damaged parts onthe clamp. See Service Bulletin WA-1132 for details.4. Check the clamps for proper location. The longer grabber brackets are used on the front axle, the shortergrabber brackets are used on the rear axle. Note that this does not apply to UHR units, however each tar-get and clamp is assigned a separate wheel position with UHR.5. Check that the targets are in good condition and are firmly secured to the wheel clamps.6. Using Data Examination check that the RMS, Blobs and Strobe parameters are nominal for each target.See the appropriate Service Manual for details.Items to check on the Alignment Rack1. Ensure that the turn plates move freely and have an adequate range of motion. Older turn plates may haveinsufficient travel. Turn plates should be checked under load with a vehicle on the rack.2. Ensure that the slip plates move freely and have an adequate range of motion. Slip plates should bechecked under load with a vehicle on the rack.3. Ensure that the rack is reasonably level and does not move or twist when under load. Runways, turn platesand slip plates may undergo camber changes when under the load of a vehicle.4. Verify lock consistency by entering the All Readings screen and observing for camber changes at all lockpositions.5. Ensure that the rack is parallel and level across the runways.6. Ensure that the rack is coplanar. Use the Rack Check test located in Diagnostics to check for coplanarrunways. Note that Rack Check is not available on UHR models. Test the rack for coplanar with a 4 foot level on UHR units.Calibration Checks1. Perform a rollback using a vehicle with no worn or loose suspension parts. Insure that the suspension issettled properly. Proceed to Rear Meters. Roll the vehicle back and forth a few times while observing the meters for changes in camber or toe. Changes in camber or toe greater than 0.05 degrees indicate a Tar-get Identification (TID) problem. Repeat this test while observing the Front Meters. The unit must be set to read in high resolution.2. UHR ONLY. Simulate a rollback while in Data Examination. The RMS values should not exceed 0.14 onany target during the rollback process. Higher RMS values indicate that TID should be performed on the effected target or targets.3. Using the same vehicle enter the Vehicle Dimensions screen (if available). Errors in Wheel Base greaterthan 0.2 inches may indicate a problem with Relative Camera Positioning (RCP).Calibration NotesIf all of the above items have been checked the unit may require a calibration. The existing calibration should be backed up prior to performing a Target Identification (TID) or Relative Camera Positioning (RCP) procedure. See the appropriate Service Manual for details.Note: That RCP and TID procedures are conducted at the factory prior to shipping the unit. The pro-cedures used at the factory are more accurate than field procedures due to the greater degreeof precision of the factory fixtures. Calibration should only be performed when required due toparts replacement or when the items listed above fail to resolve the problem.If calibration is required it is preferable to perform a TID procedure before attempting an RCP. If the problem can be attributed to one wheel it is possible to TID that wheel only. When doing a TID the vehicle being used must not have any worn parts. The vehicle must be lowered on one of the locks of the jack beam. Failure in any of these steps can and will result in an error of the TID process. Test the unit in question after the TID is performed. Per-form an RCP only if the TID procedures failed to solve the problem.UHR only. All four sets of targets must be done on the front wheels only. When doing a TID on a UHR system NO OTHER target can be in the cameras field of view during the process of an individual TID. Failure to follow these procedures can and will result in errors.Items to check with the OperatorAsk the operator to perform an alignment procedure. Observe that the operator is using proper procedures during the alignment process. Items to check include:1. Does the operator pull on to the rack with no sharp turns or corrections? Sharp turns can bind the vehiclesuspension. Rolling the vehicle back and forth a few times on the runways will help to relax the suspen-sion.2. If the vehicle has been elevated prior to conducting measurements, insure that the operator has jouncedthe vehicle thoroughly. Roll the vehicle back and forth a few times on the runways to help to relax the sus-pension. In some cases the vehicle may need to be removed from the rack, driven and then put back on the rack before conducting measurements.3. Inspect the vehicle for loose or damaged suspension parts that could move during alignment proceduresand cause repeatability issues.4. Check that the tire pressures are set to manufacturers specifications. Air pressure in tires on the same axleshould be equal.5. Ensure that the vehicle does not have mismatched wheels or tires. Tires must be the same size on eachaxle. Ensure that the wheel and tire types on each axle are the same. Note that wheel and tire type or size can vary between front and rear axle, but wheel size, type and tire size must be the same for both wheels and tires on the same axle.6. Ensure that the Targets and Wheel Clamps are mounted properly. All grabbers must be set in either thenormal or the over the hub cap position. All grabbers must be seated in the inside bracket position or all grabbers seated in the outside bracket position for proper target centering.7. Ensure that the rack is firmly on the locks before making any measurements or adjustments.8. Ensure that the operator does not jerk or jounce the suspension during the rollback procedure.9. Ensure that Wheel Wobble is turned on (Pro-42 units) and that Wheel Wobble warnings are not bypassed.10. Ensure that the turn plate and slip plate pins are removed after Rollback.11. Ensure that all instructional prompts such as install the brake pedal depressor, install the steering wheelholder or jounce the suspension are being followed by the operator.12. If performing a Caster Swing, ensure that any Wheel Roll Detected messages are not ignored by the opera-tor.13. Ensure that the operator is using proper methods to center the steering wheel. See Service Bulletin WA-1116 for details.14. Recommend that the operator use EZ-Toe. This is required for vehicles equipped with Electronic PowerSteering (EPS) units. Note that it is not required that the vehicle be steered when using EZ-Toe.15. If toe is to be adjusted ensure that the operator loosens the adjusting sleeves on both sides before attempt-ing any adjustments.16. If the operator is using an Elevated Adjust assistant be sure that the screen prompts are followed exactly.Ensure that the turn plate and slip plate pins are removed before lowering and jouncing the vehicle.17. Ensure that the operator is not adjusting toe while elevated. The toe meters are for reference only whenusing an Elevated Adjust assistant.18. When applicable to the vehicle ensure that the operator is using the Drag Link or Single Tie Rod AdjustmentAssistants. This will help to maintain accuracy and repeatability with these types of vehicle.。

Snap-on 电动螺丝刀系列产品说明书

Type Torque rangeDrive Weight kg Length mm Ordering No.Nm ft lb MWR-25 S 5-25 3.7-18.49x120.4461778439 0044 00MWR-50 S 10-507.4-36.99x120.5652348439 0044 01MWR-85 S 17-8512.5-62.79x120.6303078439 0044 02MWR-200 S 40-20029.5-147.514x180.8514198439 0044 03MWR-300 S 60-30044.2-221.214x18 2.58988439 0044 04MWR-25 TA 5-25 3.7-18.49x120.4461778439 0044 20MWR-50 TA 10-507.4-36.99x120.5652348439 0044 21MWR-85 TA 17-8512.5-62.79x120.6303078439 0044 22MWR-200 TA 40-20029.5-147.514x180.8514198439 0044 23MWR-300 TA 60-30044.2-221.214x182.58988439 0044 24Mechatronic Wrench SystemSoftware Ordering No.ToolsTalk BLM 1 User License 8059 0981 10ToolsTalk BLM 5 User License 8059 0981 11ToolsTalk BLM 10 User License8059 0981 12ToolsTalk BLMPlant License 8059 0981 13Controllers Ordering No.Focus 618439 0044 31Power Focus 60008436 1800 02MWR - KIT Ordering No.MWR - KIT4027 5022 06MWR - KIT Power Supply4027 5022 11MWR - KIT Power Cable for Power Focus 60004027 5022 12IAMOrdering No.IAM Power Focus 8436 0910 00AccessoriesOrdering No.Charging Cradle MWR 4027 5022 10MWR Protection Cover 4027 5026 28Setting key MWR/CWR4027 5013 96Recharg. battery NIMH AAA MWR 1.2 V, 1000 mAh4027 5021 01Stacklight ESL-04 Standard 8433 0570 13IO Expander (open)8433 0564 39IO Expander (sealed)8433 0564 45Focus 61 Dig. Out Connector (no cable included)4027 5022 04Antenna 868 MHz 4027 5022 13Antenna915 MHz 4027 5022 14Cable-Antenna, 2,5 m 868/915 MHz 4027 5022 15Extended Cable-Antenna, 5 m 868/915 MHz4027 5020 95MWR KIT BNC adaptor4027 5022 08MWR protection cap 5PCS (blue) 4027 5022 20MWR protection cap 5PCS (green) 4027 5022 21MWR protection cap 5PCS (red) 4027 5022 22MWR protection cap 5PCS (Colormix) 4027 5022 23MWR protection cap 5PCS (gold) 4027 5022 24MWR protection cap 5PCS (black)4027 5022 25Atlas Copco BLM Milan, ItalyVirtual Station Ordering No.Batch Control 1 License 8436 1960 10Station Control 1 License 8436 1960 30Critical Control 1 License 8436 1960 40Process Control 1 License8436 1960 50Simpler controllerOne controller - One platformPower Focus 6000 increases your flexibility in rebalancing assembly lines. By having 6 Virtual Stations you can connect up to 6 Atlas Copco tools to the same controller. Electrical tools or manual wrenches – simpler installation, easier production integration, less floor space utilization and a lower environmental footprint.Manage your entire tightening process with one of our two available controllers. Focus 61 is able to operate 2 Virtual Stations simultaneously in order to easily handle multi-operator applications.Smart Wireless WrenchMechatronic wrenches combine productivity of a click wrench with traceability of an electronic one. Using the mechatronic wrench series you are able to get access to inaccessible joints for electronic tools, keeping handling ergonomic for operators and add full traceability with trustable results.。

Snap-on torque wrenches说明书

World Leader In Torque Tools.Snap-on® gives you more ways to turn more fasteners than anyone else, and most importantly, we give you all the options you need to tighten them correctly. Snap-on gives you the advantage of the largest selection of torque tools. So whether you are looking for torque screwdrivers or full featured calibration systems, we have the products in the styles and the ranges you need.These are the products that have earned their reputation in the real world where it matters most – in the factories and shops, in the ﬁ eld and in the laboratories. They are products trusted to build jet engines and farm tractors, spacecraft and machine tools, nuclear reactors and automobiles. Whenever rotating assemblies or high stresses occur, that’s where you’ll ﬁ nd the world’s ﬁ nest torque products.Snap-on torque wrenches are made in City Of Industry, California.TECH3FR250TECH4R6003/4Sealed Flex Head Sealed Fixed Ratchet 3211°720-720060-60081-8131 1/42 1/2Red 48RKRS936RKRQC4Torque WrenchesTECHANGLE™ Models / 2% Accuracy / Flex Head Specifications ATECH2FR100ATECH3FR250Square Drive, inches 3/81/2Head Type Sealed Flex Head Sealed Flex Head Gear Teeth 3636Gear Action 10°10°Range, in. lb.60-1200150-3000TECH3R2501/2Sealed Fixed Ratchet 3610°300-30003/41 5/8Red 26 1/4RKRS936The certification of accuracy provided per ASME and ISO Standards is 20% to 100% of full scale.8% CW, 12% CCW from 10-19% F.S. 16% CW, 20% CCW from 5-9% F.S. (TECH Y only)• Tolerance (early preset alert) - 2% of torque settingTechAngle™ wrench eliminates the need for angle gauges andprotractors, providing the most accurate and fastest way to achieve torque plusreadout shows you your torque setting, and then changes to the follow up angleTECH2FR100TECH2R100ATECH2FR100do the job of multiple torque wrenches and an angle gauge tocomplete precise “torque plus turn” specifications at a fractionof the cost. And even better, it saves you some serious time on26 (660)48 (1,219)RKRS936RKRQC4Red3.7 (1.68)10.0 (4.54)The certification of accuracy provided per ASME and ISO Standards is 20% to 100% of full scale.Memory Models / 4% Accuracy / Interchangeable Head and "D" ModelsSpecifications TECH1JM240TECH1JDM240TECH2YDM100TECH3XM250TECH3XDM250 Head Type Interchangeable Interchangeable Interchangeable Interchangeable Interchangeable Range, in. lb.24-24024-240300-3000300-300025-25025-25034-33934-339X (0.735")X (0.735")(1 N•m, 1 in lb.)1 ft. lb.(1 N•m,1 in lb.)1 ft. lb.(1 N•m, 1 in lb.) Red Grey23 1/ (597)23 1/ (597)TECHWRENCH FEATURES: (all "D" models)• Hidden Torque Preset Adjustment (momentary display at Zero/Tare)• Hidden Tolerance Adjustment + and – 1 to 16 percent of preset value• Military—document compliance with maintenance schedules and inspections • Aviation—include torque data in maintenance reports Comfortable, non-slip grip handle. Stand on handle bottom keeps tool from rolling off flat surface. Flex head ratchet moves 15º. All models have a Low Battery Indicator and Auto Shutoff (after 2 minutes idle). Designed to withstand shocks without failure. Splash-proof to protect against water and most automotive shop fluid. Includes storage case. EU/CE—DE, ES, FR, IT, NL, PT, UK all models. Also Japanese language. Complies with ISO-6789-2003 and ASME B107-28-2005 Standards. Additional technical TECH2YDM100TECH2FRM100TECH3XD250TECH2YM100WARNING• Do not exceed rated torque.Range, min.Range,max.IncrementsLength,in.HeadWidth,in.HeadDepth,in.StorageCaseRatchetServiceKitQD2100QD2R100Adjustable Click Type Torque Wrenches Torque4% AccuracyRange, min.Range, max.Increments Length, in.Head Width, inches Head Depth, inches Storage Case Ratchet Service Kit 12 dN•m 60 dNvm .5 dN•m 9 7/87/87/16PBQD1RKRT93650 dN•m 250 dNvm 1 dN•m 11 3/47/87/16PBQD1RKRT93650 dN•m 250 dN•m 1 dN•m 11 3/47/87/16PBQD2RKRFC93610 N•m 50 N•m .5 N•m 15 9/16 1 5/329/16PBQD2RKRF93620 N•m 100 N•m .5 N•m 15 9/16 1 5/329/16PBQD2RKRF93640 N•m 200 N•m 2 N•m 19 1 5/83/4PBQD3RKRS93670 N•m 350 N•m 2 N•m 24 3/161 5/83/4PBQD3RKRS936150 N•m 800 N•m 5 N•m 42 3/4 2 1/2 1 1/4PBQC4RKRQC4WARNING • Do not exceed rated torque.Preset Torque Screwdrivers / ±6% Accuracy QDRIVER4NM 90 - 450 N•cm Torque ScrewdriversQTS135 U.S. Preset Limiting Driver. A torque limiting screwdriver featuring a clutch mechanism to help prevent over torquing by allowing freerotation upon reaching the set torque value. Ideal selection for assembly line workwhere the same requirement is constant. Wrench can be reset at different torque valuesor readjusted for accuracy whenever necessary.QD2RN50QDRIVER3P QDRIVER3QTS135orientation. In all other positions, guaranteed accuracy is ±5%. Accuracy is guaranteed in the clockwise direction from 20% of capacity to full capacity.• "Split Beam" Measuring Element — provides accurate, reliable readings andeliminates the heavy coil spring used in conventional click type wrenches. Thisyields fewer moving parts, reducing friction and wear U.S. Reading Torque Wrenches with Conversion Scale - ±4% AccuracyRange, Range, Length, Head Width, Head Depth,* Ratchet Service TQFR250ETQR600ETCR175TORQOMETER U.S. Reading - Standard 2% AccuracyWidth, inches Head*Depth,inchesStorageCaseNewton Meter Reading - Standard 2% AccuracyBasic Models Follow-upModelsSignalModelsRange,N•mIncrements,N•mLength,inchesWidth,inchesHead*Depth,inchesStorageCaseTE50FUATESI75TE175LTESI75LWARNING• Do not exceed rated torque.Combination U.S./Metric Reading - Standard 2% AccuracySq.Dr.in.Basic Models Follow up Models Signal Models Metric Range Metric Increments U.S.Range U.S.Increments Length,inches Width,inches Head*Depth,inches Storage Case 1⁄4TEC1A TEC1FUA —16 kg•cm 1 kg•cm 15 in. lb..5 in. lb.9 29⁄32 2 11⁄16 1 1⁄4PB9TEC3ATEC3FUA —35 kg•cm 1 kg•cm 30 in. lb. 1 in. lb.9 29⁄32 2 11⁄16 1 1⁄4PB9TEC6ATEC6FUA —90 kg•cm 2.5 kg•cm 3⁄8TEC12A TEC12FUA TEC12LA 175 kg•cm 5 kg•cm TEC25FATEC25FFUA TEC25FLA 350 kg•cm 10 kg•cm TEC50ATEC50FUA TEC50LA 700 kg•cm 20 kg•cm 1⁄2TEC51TEC51FU TEC51L 700 kg•cm 20 kg•cm TEC100TEC100FU TEC100L 14 kg•m .5 kg•m TEC175TEC175FU TEC175L 25 kg•m 1 kg•m TEC250TEC250FU TEC250L 35 kg•m 1 kg•m 3⁄4TEC352A TEC352FUA TEC352LA 50 kg•m 1 kg•m TEC602ATEC602FUA TEC602LA 80 kg•m 2 kg•m 1TEC803**TEC803FU**TEC803L**110 kg•m 2 kg•m —TEC1003FU**TEC1003L**136 kg•m 2 kg•m —TEC1503FU†TEC1503L†200 kg•m 5 kg•m —TEC2003FU†TEC2003L†280 kg•m 5 kg•m 1 1⁄2TEC2005†TEC2005FU†TEC2005L†280 kg•m 5 kg•m Torque TORQOMETER ® Torque WrenchesCombination U.S./Newton Meter Reading - Precise 1% AccuracyBasic Models Follow up Models Signal Models N•m Range N•m Increments U.S.Range U.S.Increments Length,inches Width,inches Head*Depth,inches TER1A TER1FUA — 1.7 N•m .05 N•m 15 in. lb..5 in. lb.9 29⁄32 2 11⁄16 1 1⁄4TER3ATER3FUA — 3.5 N•m 0.1 N•m 30 in. lb. 1 in. lb.9 29⁄32 2 11⁄16 1 1⁄4TER6ATER6FUA —8.4 N•m 0.2 N•m 75 in. lb. 1 in. lb.9 29⁄32 2 11⁄16 1 1⁄4TER12A TER12FUA TER12LA 17 N•m .5 N•m 150 in. lb. 5 in. lb.9 29⁄32 2 11⁄16 1 1⁄4TER25ATER25FUA TER25LA 3200 N•cm 50 N•cm 300 in. lb. 5 in. lb.9 29⁄32 2 11⁄16 1 1⁄4TER50ATER50FUA TER50LA 60 N•m 1 N•m 600 in. lb.20 in. lb.12 1⁄2 2 11⁄16 1 1⁄41⁄2TER51TER51FU TER51L 60 N•m 1 N•m 600 in. lb.20 in. lb.15 2 11⁄16 1 5⁄16TER100TER100FU TER100L 140 N•m 5 N•m 100 ft. lb. 2 ft. lb.16 2 3⁄4 1 3⁄8TER175TER175FU TER175L 230 N•m 10 N•m TER250—TER250L 340 N•m 10 N•m 3⁄4TER352A TER352FUA TER352LA 480 N•m 10 N•m TER602ATER602FUATER602LA800 N•m20 N•m1TER1003**TER1003FU**TER1003L**1360 N•m 20 N•m TER175TEC175TER175L TEC175LWARNING • Do not exceed rated torque.U.S. Reading Standard 2% Accuracy Standard Follow up Models Length, inches Stubby Basic Models TORQOMETER U.S. Reading Standard 2% AccuracyTEXC2003TFU TA362TEX602TLA TQSC4FUA TQSSC4FUA85TQPTorque Wrench Bodies/Adjustable/±4% AccuracyTorque Wrench Bodies/Pre-Set/±4% AccuracySquare Drive Heads / RatchetingAllow use of torque wrench bodies above with sockets, crowfoot wrenches, or other similar attachment.11/64QYD Series - 3.00"RKRF93611/64QXD Series - 4.50"RKRS93611/64QZD Series - 5.75"RKRQC411/64RKRQC5Center of Fastener to Retaining PinQJD Series - 2.50"QYD Series - 3.00"QXD Series - 4.50"QZD Series - 5.75"QC1I200QC1P300QC3P200QJD12AQYSD16AQJO28AQJOM11AWARNING• Do not exceed rated torque.Torque Heads for Click Type Torque WrenchesQXX52AQJX12ACenter of fastener to retaining pin:* QJXM Series - 2.50"12-Point Box End HeadsJ (0.425")Y (0.560")X (0.735")Z (0.990")Head Depth, QJX8A (220)QJX9A (250)QJX12A (490)QJX14A (715)QYXM21ACenter of Fastener to Retaining QJRXS Series - 2.50"QYRXS Series - 3.00"QYRX Series - 3.00"QJRO Series - 2.50"QJRX18AWARNING• Do not exceed rated torque.GA184AGA190Geared Head MultipliersSome models feature a replacement square drive to protect components by automatically shearing when rated output is exceeded by 3% to 10%. All models include an input/output conversion chart in ft. lb. and N•m.YA290PLUS YA300YA391YA393YA394YA395Bar Plate Plate 3,2005,0008,00017318915420.25:129.25:160.0:118.5:1*26.5:1*52.0:1*3221/21/21/211 1/2 1 1/2Needle Needle Needle 201515 1/248 5/6YA391YA394YA390ED2600SquareDrive, inchesRange, maximumRange N•m• Largest Storage Capacity Available–up to 4,000 torque values can be stored in memory• Downloading Capability–individual torque values and store values in memory may be directly downloaded to a printer or data logger via an RS-232 connection • Selectable Modes of Operation–"peak hold" and "track" modes of operation are standard • Range–available from 5 in. lb. to 600 ft. lb.Engineering units can be selected through the keypad (in. oz., in. lb., ft. lb., N•m, dN•m, k•gm, and kg•cm)• Accuracy–±1% from 10% to 100% of scale• Quality Construction–proven industrial quality. All ELECTROTORK ® electronic torque wrenches are Feature a high degree of accuracy either clockwise or counterclockwise regardless of handhold position. Easy-to-read scales and sealed membrane keypad enhance operator usefulness. Each wrench includes Length, inches13 1/214 7/814 7/821 1/246 1/2Torque Wrenches. The certification of accuracy provided QC1ETT50QCE215AWARNING• Do not exceed rated torque.• Over torquing can cause breakage. Wrench can break while breaking fasteners loose. An out of calibration torque wrench can cause part of tool breakage.• Periodic recalibration is necessary to maintain accuracy.• Do not use a torque wrench to break fasteners loose.All Snap-on ® Torque Wrenches, Drivers and Testers are provided with a Certificate of Calibration. All wrenches and drivers are calibratedper ASME B-107-14 and ISO 6789 Standards for Accuracy, from 20% to 100% of full scale, using NIST traceable equipment.Electronic Torque WrenchesTorqueVERSATORQ1®Torque Acquistion MeterIncludes VERSACHARGE1 Chargerand PB57A Case.Sensors sold separately.Electronic Torque Acquistion MeterPerforms most of the same functions as theTorque Acquisition Meter. Will notperform the Data Storage/Recall, Statistical Analysisand Histogram functions and does not offer the SerialVERSAMETER®System AccessoriesNOTE: Please reference the VERSATORQ® instructionmanual for the sensor ranges and resolutions indifferent units of torque measurement.VERSA2S100All TTC Series Transducers include the correct adaptor for the indicated torque range.Square Drive Size Range Bench TopMounting Bracket1/4 15-200 in. oz.TTC34211/4 4-50 in. lb.TTC34211/4 15-150 in. lb.TTC34213/8 30-400 in.lb.TTC34213/8 80-1000 in. lb.TTC34211/2 10-125 ft. lb.TTC34221/2 20-250 ft. lb.TTC34223/460-600 ft. lb.TTC34221 100-1000 ft. lb.TTC15001VERSATEST ™ Specifications:Large 5.5" x 1.5" backlighted LCD graphics displayTwo, Normally Open, Form A, Rated 12VDC @ 1/2A closecontact at 110% CW or CCW or torque/force transducer range* TTC Transducers used with, but not calibrated to, the VERSATEST™ Indicator provide a system accuracy of +/- 0.5% of reading @ 25° C.VERSATEST600Electronic Torque Metering SystemProvides high speed monitoring of static and dynamic torque inputs. Includes the VERSATEST™ Indicator, VERSA600LDR Loader, TTC12 Transducer, TTC400 4-in-1 Transducer and TTC5000-1 4-in-1 Adaptor Plate.VERSA600LDR Mechanical Loader. Portable, table top torque wrench loader with safety shield. Unit will load dial, micrometer, beam and electronic torque wrenches. Optional torque screwdriver testing kit allows testing of torque screwdrivers. Maximum capacity of 600 ft. lb. Use with any TTC Series Transducer from 15 in. oz. to 600 ft. lb. Four cushion pads for adhesion to work surfaces without slipping. Large wheel for smooth cranking action.VERSATEST™VERSATEST600TTC400WARNING• Counter balance or anchor mounting base.mounts in this location.TTC2000Basic System.Optional accessories on next page. TTC2000 / TTC2800 System ComponentsElectronic Torque Tester and Calibrator TransducersAll TTC Series Transducers include the correct adaptor for the indicated torque range.Range Bench Top MountingBracket• Reaction arms, cables, mounting plates and fixtures are available for testing tensi-40" Calibration Arm, 1 /4" sq. dr. with adaptorsConnects TTC610 Digital Indicator to PC.Connects TTC610 Digital Indicator to printer.Free standing calibration stand with mounting block and hardware for use with TTC2000/TTC2800 Systems and all TTC8TTC400TTC2600QC2JRS400TTC25002WARNING• Counter balance or anchor mounting base.TTC2610TTC2620TTC26302Six tons of controlledhydraulic power for removalof frozen or corroded nuts up to 2Hhardness and 1 3/4" across the flatsor 2" hex on soft nuts. IncludesCG652 Ram and Pump Set. Has aNut splitter withoutacts as a handle to hold tool securely.Hydraulic Cable Cutters Cut steel cable up to 1 1/2" in diametereasily with up to 29 1/3 tons of force generated byNut Splitters and Cable Cutters Nut Splitters Cable CuttersElectronic Bench Top Torque Testers See Warranty Information on inside front cover..002 ft. lb., 02 in. lb., 025 in. oz., .002 N•m., .0002 kg•m., .02 kg•cm .01 ft. lb., 1 in. lb., 2 in. oz., .01 N•m., .001 kg•m, 1 kg•cm .01 ft. lb., 1 in. lb., 2 in. oz., .01 N•m., .001 kg•m, 1 kg•cm TBT600A CG675HY NC52CG410HYP R O D U C T P R O D UC T N E W Rethreading Tools, pgs 337-339。

Snap-on扭矩工具的使用

400 牛米的扭矩
2米的长度米的长度 200 牛顿的垂直力
扭矩的原理
• 扭矩在加长情况下的公式转换: 扭矩在加长情况下的公式转换 L=LA+LB F 不变 T=L x F TA=LA x F T/L=TA/LA T/(LA+LB)=TA/LA T=TA x (LA+LB)/LA
扭矩的原理
扭矩的原理
扭力扳手的使用注意
• • • • • • • • • • • • • • • 因为Snap-on通过了ISO6789和ASME107的标准,所有我们给出专业的建议所有的扭力工具需要经常的定期的计量， Snap-on建议每六个月或者每使用5000周次检定一次扭力工具应该被妥善储藏和保管，不要靠着放（容易倾倒）永远不能被用来松螺丝,只能用来扭紧螺丝可调式扭力工具使用前应该预扭几次,使用完后应该归零存放永远不能超扭矩使用选型时如工作扭矩在200Nm那我们应该选择400Nm也就是50%量程，预置式 200Nm 400Nm 50% 扭力扳手除外。使用时应握住把手的中心，用力要垂直扭力扳手，偏差不得大于10度在要到达要求扭矩时应缓慢而匀速如果扭力工具被砸或者被摔则千万要重新计量才能使用不能使用过长的加长杆来工作否则很容易超扭矩检查扳手外观特别是头部紧固螺栓后才能使用使用扭力扳手永远只能拉，而不是推请勿用手扶扭力扳手头部
1 2 4 3
扭矩的单位
1 ft-lb = 12 in-lb 1 in-lb = 16 in-oz 1 Nm = 10 dNm 1 dNm = 10 cNm 1 kgm = 100 kgcm English ft-lb
International System Nm
Metric kgcm扭力源自手的类型Snap-on 工具细解

Snap-On Modis多功能诊断工具说明书

TRUST IS THE KEY TO ANYThere’s trademarkSnap-on Scanner, combined with scope-based component testing, and a graphing digital ohm/volt meter. So youcan pretty much count on it being the go-to-tool to get the job done. With the benefit of Snap-on’s experience-based Troubleshooter and Fast-Track component test information, you never work alone when you have MODIS in your hands. Plus, expandability means you are always up to date. With MODIS, you get results you can trust and answers you can trust. That means your customers will keep coming back to the technician they trust—you.Snap-On Modis SpecsProvided by Features:THIS IS HOW THE GUYWHO HAS ALL THE ANSWERS GOT ALL THE ANSWERS.ETHOS ®SOLUS PRO TMVANTAGE PRO TMMODIS TMVERUS ®VIN-specific scanner coverage Reads and clears codes and data Functional tests/Bidirectional controlsRelearns and adaptations 2-Channel high speed oscilloscope 4-Channel high speed oscilloscope Digital/Graphing Volt/Ohm meter Full-color display Bilingual (English/Spanish)High capacity internal hard drive Removable flash drive storage port Wi-Fi enabled & Internet browser Rechargeable battery Windows ® CE Windows ® XPFast-Track ® Troubleshooter Fast-Track ® component tests (US, Asian, European)1980-current US OEM-level scanner coverage1983-current Asian OEM-level scanner coverageOptional European OEM-level scanner coverage44816Simultaneous live scan data graphsProgrammable Function Key TouchscreenDIAGNOSTIC TOOLSQUICK REFERENCE GUIDE。

大众品牌经销商工具设备配备标准(经销商版)2010.8.6

7
1
1
1
1
标配 VAG
德国
VAG1576
3,958
3,958
3,958
3,958
3,958
8
2
2
2
1
标配 VAG
德国小计：
VAG1783
1,884
3,768 21,771
3,768 21,771
3,768 21,771
1,884 12,865
（四）发动机、变速箱维修专用设备 9 内窥镜 1 1 1 0 标配 VAG 德国 VAG1764B 16,732 16,732 16,732 16,732 0 检查发动机油道、水道、气缸等内腔是否有一汽-大众文化异物公司
举升力3.5吨,价格不含液压油,桥式二次举升一汽-大众文化机公司
轮胎动平衡机 29 轮胎动平衡机 1 1 1 1
标配百世霸
德国进口
TWZ MT825
21,525
0

0
0
0 检测调整轮胎不平衡量
一汽-大众文化公司一汽-大众文化公司一汽-大众文化公司一汽-大众文化公司
标配
Snap- 昆山 on 国产德国进口
VAS6150附件包，含Linda PA1580-1745车一汽-大众文化载电源和电脑包公司
3
车载电源和电脑包
1
1
1
1
标配 SPX
进口+ Linda PA1580国产 1745 小计：
1,396
1,396
1,396
1,396
1,396
38,181
38,181
38,181
38,181

Snap-on Equipment 车轮平衡器部件清单说明书

Parts ManualTable of ContentsBOM - EEWB330A (3)BOM - EEWB333A (3)BALANCER ASSEMBLY (4)1D SAPE ASSEMBLY (6)2D SAPE ASSEMBLY (7)UPPER DISPLAY (8)VIBRATORY ASSEMBLY (9)CONES & ACCESSORIES (10)STANDARD MOTORCYCLE ADAPTERS (11)NOTES:BOM - EEWB330ABOM - EEWB333APART NUMBER DESCRIPTION EAA0369J73ABAL ASSY – SNA HAND SPIN MOTORCYCLE 7-16701AADAPTER-AC 120VAC-9VDC 1.8A 2-3657CABLE CLAMP (FLAT CABLE)PAK306330CARTON - SMALL ADT KIT (110372)PAK321580CARTON-Y2K (2685-01)PAK710770PALLET-Y2K (2688)1-01215ASCREW - LAG, 5/16 X 1 ½1-541WASHER - FLAT, 5/16ZEEWB330A9LIT PACK SNAP-ON HAND SPIN EAL0341J96ALABEL – BALANCER WARING, REAR EAL0341J97ALABEL – BALANCER WARING, SIDE EAL0341J60ALABEL - PATENT, WHEEL BALANCER EAL0343J76BLABEL-ELECTRICAL/SERIAL EAL0352J20ALABEL - SNAP-ON, WHITE EAL0352J19ALABEL – SNAP-ON BIG S 5403CERTIFICATE-INSTALL REGISTRAT EAK0221J13AADAPTER KIT-MOTORCYCLE EAM0006G16ABOLT-FRENCHHANDLE M10-1LH EAC0054P14AHANDLE-FRENCH LEFT HAND CRANK EAM0005D40A CALIBRATION WEIGHTPART NUMBERDESCRIPTION EAA0369J72ABAL ASSY – SNAPON HAND SPIN 7-16701AADAPTER-AC 120VAC-9VAC 1.8A 2-3657CABLE CLAMP (FLAT CABLE)PAK306330CARTON - SMALL ADT KIT (110372)8-40460ACARTON NEW ALIGNER 8-04664ASKID BALANCER 44.5” X 35”1-01215ASCREW - LAG, 5/16 X 1 ½1-541WASHER - FLAT, 5/16ZEEWB330A9LIT PACK - SNAP-ON HAND SPIN EAL0341J96ALABEL – BALANCER WARING, REAR EAL0341J97ALABEL – BALANCER WARING, SIDE EAL0341J60ALABEL - PATENT, WHEEL BALANCER EAL0343J76BLABEL-ELECTRICAL/SERIAL EAL0352J20ALABEL - SNAP-ON, WHITE EAL0352J19ALABEL – SNAP-ON BIG S 5403CERTIFICATE-INSTALL REGISTRATION EAA0247G21ACALIPER - RIM WIDTH EAA0263G79AQUICK NUT KIT, 40MM EAK0309J28AKIT – 4 CONES EAM0005D40ACALIBRATION WEIGHT EAM0006G01AHOOK - ACCESSORY STORAGE EAC0060G02AFLANGE - COVER, ACCESSORY HOOK 58839 WEIGHT TOOLSYM REQ PART NO DESCRIPTION1 4 1-07439A NUT - SPEED, “U” TYPE,2 2 1-11633 NUT-M6 X 5,2MMTHK, BLK3 1 1-12944A SPACER - .PULLY .62 OD X .13 LG4 1 1-14944A WASHER - NYLON SHOULDER, .358 ID5 1 1-1548 WASHER-EXT,SHAKEPROOF 6MM6 2 1-16309 SCREW - SHCS, M6 X 16MM,7 4 1-17659A NUTSERT - M108 6 1-18523A1 SELF TAPPING SCREW D4,8X13MM9 1 1-2676 PLUG-HOLE, 2”DIA10 4 1-3724 SCREW-SELF TAP,5 X 10MM11 4 1-44009A SCREW-BHCS, 1/4-20 X 7/812 1 1-6668 COMPRESSION SPRING13 1 1-7558 POP RIVET-3/16”14 1 2-23201 TERMINAL LUG-6.3MM X .8MM POP RIVET15 3 8-7216 PLUG-HOLE, 16MM DIA16 1 EAA0263G07A ASSY-BRAKE PEDAL17 1 EAA0332G65A VIBRATOR HAND INT.FLANGE18 1 EAA0338G73A STAND. SAPE 1D-2D ASSY1 EAA0346J28A ASSY - SAPE JB VPI 1D, S1 (EEWB333A - MOTORCYCLE)19 1 EAA0369J30A CABINET ASSY - S2, RED20 1 EAA0370G36A INTEGRATED DISPLAY PANEL21 1 EAC0053J15A BRAKE SPACER22 1 EAC0054P00A JBEG WEIGHT23 1 EAS2021J05A PANEL-COVER,GUARD ACCESS24 1 EAS2113J77A BRACKET - CAL WEIGHT25 1 EAS2118J57A PANEL - COVER, ELEC ACCESS26 1 EAW0233J48A CABLE ASM - POWER, HAND SPIN1 EAL0352J11A SNAP ON DECAL1 EAL0352J19A SNAP ON “S”VIBRATORY ASSEMBLYEAA0332G65AREF QTY PART NUMBER DESCRIPTION1 1 1-11833 NUT M82 1 1-13204A SCREW3 2 1-17403 SCREW4 2 1-19903A 4 X 65 COUNTER SUNK SCREW5 2 1-2967 PRETENSION SPRING6 1 1-4034 NUT HEX BM (M 10)7 1 2-09337A SOLENOID STOP8 4 8-1144 STEEL BALL9 1 EAA0344G00A ENCODER10 2 EAA0260D59A PIEZO11 1 EAA0263G26A BRAKE12 1 EAA0263G26A BRAKE BAND13 2 EAM0005D07A SET SCREW M10 X 29NS 1 EAW0240G67A OPTO CABLE1356247891011121013Ref Qty Part NumberDescription 1 1 1412Spring 2 1 3607-01Spring 3 1 3609-01Spacer - M/C shaft 4 1 EAC0054P14ASpin Hand Crank handle 1 EAM0006G16ABolt - Crank handle (Not Shown)5 1 EAM0005D62AExtension Gauge 6 1 8430-02Caliper M/C 7 1 EAA0255J43AFlange 8 1 EAM0003J33AShaft 14mm 9 1 1401Spring 10 2 1387Cone 11 2 1389-01Pressure Disc 12 1 1389-02Pressure Disc 13 1 1388Ring Nut Items 8 thru 13 EAK0221J15AMotorcycle adapter kit STANDARD MOTORCYCLE ADAPTERS EAK0221J13A EEWB333 - PARTSNotice: The information contained in this document is subject to change without notice. Snapon Equipment makes no warranty with regard to this material. Snapon Equipment shall not be liable for errors contained herein or for incidental consequential damages in connection with furnishings, performance, or use of this material.This document contains proprietary information which is protected by copyright and patents. All rights are re-served. No part of this document may be photocopied, reproduced, or translated without prior written consent of Snapon Equipment.TEEWB330A 07/2014...rjh Printed in the U.S.A.。

汽车扭力扳手使用方法

汽车扭力扳手使用方法一、什么是汽车扭力扳手汽车扭力扳手是一种专门用于汽车维修和装配的工具，它能够精确测量和控制扳手施加的扭矩力。

通过使用扭力扳手，可以确保紧固件的扭矩力符合制造商的要求，从而避免过紧或过松导致的损坏和故障。

二、汽车扭力扳手的结构和原理2.1 结构汽车扭力扳手通常由以下几个部分组成：1.扭矩调节装置：用于设定所需的扭矩值。

2.扭矩显示装置：显示实际施加的扭矩力。

3.扭矩传感器：用于测量扭矩力。

4.扭矩释放机构：当设定的扭矩值达到后，会通过释放机构发出声音或产生其他信号提示操作者停止施力。

2.2 原理汽车扭力扳手的原理是基于弹性形变和扭矩传感器的工作原理。

当扭力扳手施加力矩时，扭矩传感器会受到扭矩的作用，从而产生形变。

这种形变会被传感器检测到并转换为相应的电信号，通过电路处理后可以实时显示扭矩数值。

三、如何正确使用汽车扭力扳手要正确使用汽车扭力扳手，需要遵循以下步骤：3.1 选择合适的扭矩扳手根据工作需要，选择适合的扭矩范围和精度的扭矩扳手。

每个车辆和每个紧固件都有不同的扭矩要求，所以选择正确的扭矩扳手非常重要。

3.2 校准扭矩扳手在使用扭矩扳手之前，需要确保其准确性。

定期校准扭矩扳手可以保证其测量结果的可靠性。

可以使用专业的校准设备或者送到专业机构进行校准。

3.3 调节扭矩值根据紧固件的要求，使用扭矩调节装置将扭矩值设定为正确的数值。

扭矩调节装置通常位于扳手的柄部，通过旋转调节装置可以改变扭矩值。

3.4 施加扭矩力将扭矩扳手与紧固件连接好，并确保扳手与紧固件垂直。

通过握住扳手的柄部，施加适当的扭矩力。

当扭矩值达到设定值时，扭矩释放机构会发出声音或者产生其他信号，表示达到了设定的扭矩力。

3.5 检查紧固件使用扭矩扳手紧固紧固件后，需要仔细检查紧固件是否符合要求。

可以使用力矩扳手重新检查紧固件的扭矩力，确保其符合制造商的要求。

四、常见问题和注意事项4.1 常见问题•Q: 如何保养汽车扭力扳手？ A: 汽车扭力扳手需要定期清洁，并保持在干燥的环境中。

Snap-on 工具集合说明书

PROPRIETARY INFORMATION OFSNAP-ONDO NOT REPRODUCE1 14KSCISSORLIFTOPEN FRONT AND REARSnap-on Incorporated is a leading global innovator, manufacturer and marketer of:•TOOLS•EQUIPMENT •DIAGNOSTICS•REPAIR INFORMATION AND SYSTEMS SOLUTIONSfor professional users performing critical tasks where SECOND BEST IS NOT AN OPTIONW h o W e A r eProducts and services include:•HAND AND POWER TOOLS •TOOL STORAGE•DIAGNOSTICS SOFTWARE•INFORMATION AND MANAGEMENT SYSTEMS •SHOP EQUIPMENTW h a t w e m a k eSnap-on IncorporatedCorporate Office Kenosha, WisconsinSnap-on Tools GroupKenosha, WisconsinRepair Systems & Information GroupKenosha, WisconsinChallenger Lifts Louisville, KentuckyVehicle liftsMitchell 1Poway, California Vehicle repair information and business management systemsPro-Cut International West Lebanon, New HampshireOn-car brake lathes, related equipment and accessoriesSnap-on Business SolutionsRichfield, Ohio Leading solutions provider for electronic parts and aftersalesbusiness performance and improvement dataSnap-on Credit LLCLibertyville, IllinoisFinancing solutionsSnap-on DiagnosticsLincolnshire, Illinois San Jose, CaliforniaHandheld and PC-based diagnostics products, service and repair informationproducts and diagnostic software solutionsSnap-on Industrial GroupCrystal Lake, Illinois Kenosha, WisconsinSnap-on/Sun de México S.A. de C.V. Tlalnepantla, MexicoSnap-on Tools International, L td.Kenosha, WisconsinWheeltronic Ltd.Mississauga, Ontario, CanadaVehicle liftsEcotechnics S.p.ASesto Fiorentino, ItalySNA EuropeParis, France (Headquarters)Snap-on EquipmentCorreggio, ItalySnap-on Tools LimitedKettering,EnglandSnap-on DiagnosticsKing's Lynn,England Snap-on Tools Pty. Ltd.National Distribution Center -SydneySnap-on Asia Manufacturing (Kunshan) Co., Ltd.INDIASnap-on Tools Private Ltd.Snap-on Tools Japan, K.K.Snap-on Tools Korea Ltd .Snap-on Tools Singapore Pte. Ltd.SNA EuropeSanto Tomé, ArgentinaSnap-on do BrasilComercio e Industria Ltda.São Paulo, Brazil Commercial & Industrial GroupKenosha, WisconsinSnap-on Conway ARUndercar equipment manufacturingPRODUCT MANUFACTURING PRODUCT DEVELOPMENTDISTRIBUTION ENGINEERINGTRAININGGLOBALOUR WORLDWIDE FOOTPRINTTHINK BIGSNAP-ON IS THE LARGESTAUTOMOTIVE EQUIPMENT MANUFACTURER IN THE WORLD We help more people daily, with critical task solutions worldwide, thanany other automotive service equipment companyEuropeOEM partners worldwide.North and Latin America may include Asian and European partners as wellEuropeEuropeEurope AsiaNorth America Latin AmericaEurope AsiaNorth America Latin AmericaEuropeEurope AsiaNorth America Latin AmericaBrazilOUR PARTNERS | WORLDWIDEOUR LEGACYOUR COMPETITORS USE OUR TECHNOLOGYSTATE OF ARTHEAVY STEEL MANUFACTURINGPROPRIETARY INFORMATION OFSNAP-ONDO NOT REPRODUCE10 MODERN MANUFACTURING PLANT3D ENGINEERINGHIGH SPEED LASER CUTTERCOMPUTERIZED FORMINGAUTOMATED ROBOTIC WELDINGAUTOMATED POWDER COATING SYSTEMSTATE OF THE ART SPRAY BOOTHFULL UP -LOAD TESTING14 K SCISSOR CLASS ALIGNMENT RACK✓14,000 LBS CAPACITY ✓Open front and rear end ✓Low profile height ✓Wide runways ✓Recessed front turn plate pockets ✓Recessed rear slip plate pockets ✓Reinforced scissor ✓Multi-position work steps ✓ 4 hydraulic cylinders ✓Steel reinforced glide blocks ✓Lock and lights PREMIUM FEATURE SETFor standard production passenger cars and pick up trucks For ease of access for adjustmentsLowered vehiclesEasier, faster, and safer vehicle positioningKeeps the surface flat Keeps the rear surface flat for less roll back effortFor longevityEasy accessImproved synchronization and equalization Longer life cycle reduced maintenanceTime saving one button operation locks, bright LED lightingPROPRIETARY INFORMATION OF26” wide runways that allows ease of drive -on with dual-axle trucks and allowingwheels to remain on the surface of platformwith no over-hang RUNWAY STRUCTURE26” wideFRONT POCKETS Recessed front pocket to allow turn plate (standard and lights and locks) for a flush mount surface•Nice even transition area •Requires minimum effort to roll the vehicle on the turn platesRECESSED REAR POCKET•Allow for flush mount rear slip plateswith a 72” long plate•Accommodate multiple length wheelbases•Slide and rotate to minimize tractionand improve adjustment REAR SLIP PLATESFLUSH MOUNT REAR SLIP PLATESENCLOSED ROLLER BEARINGS35 enclosed roller bearings per slip plate that keep dirt away from the rolling surface for ease of movementBENEFIT•Low friction for ease movement •Low maintenance•Ease of replacementPLASTIC INSERT19 plastic inserts in each slip plate in addition to rollers to distribute heavier loads evenly•Easily removable for replacement or serviceRUNWAYSHeavy duty constructed runways with added gussets welded to the under side to transfer loads from the outer side of runways to the centre and flatter surface •Improve flatness of the deck •Reduce torsional stress•Minimize deck deflection under heavy loadsLIGHTS AND AUTO LOCKS Patented Lights and Locks models incorporate flush mounted lights in the front turn plates•The lights are always properly positioned for optimal lighting•Safer and brighter than an incandescent light ata lower voltage•The lights come on and off automatically at a pre-determined heightLIGHTS AND AUTO LOCKS Patented Lights and Locks models incorporate convenient and adjustable undercar lighting in the rear slip plates•Adjustable for optimal lighting •Illuminate the undercarriage of the vehicle •Safer than an incandescent light•Very low heat signature•Comes on and off at a pre-determined heightPNEUMATIC SWITCHA pneumatic switch mounted to structureSwitch actuator controls power to lights only above“Hazardous Zone”•The switch actuator rotates with the liftas it goes up•Safety feature, no electricalcomponents under the runwaysPneumatic switch•Maximum lifting height of 72”Adjustable pneumatic switch forlowered ceiling heights or fordedicated operating alignmentheights and can be set to as low as45”OPERATING HEIGHTS72”APPROACH ANGLEThe approach angle is greatly reduce to 11 degrees thanks to a 52” long approach rampProvides additional ground clearance for vehicles with lower ride heights or low clearances due to aero packages for exampleRUNWAY HEIGHTSuperior engineering and advanced manufacturing processes along with exclusivehydraulics for a lower deck heightThe runway height is approximately 10inches when fully collapsedWORK STEPSWork steps that can be moved (8 positions) along side of runways •Conveniently allows access for under hood or entry in to the vehicle withease and without having to lowervehicle all the way down•Can be removed when not in use and stored under the front of the rackContained glide block tracks, on the baseframe•Containing the glide blocks reducescontaminant intrusion behind the block,reduces wear and tear•The U shape channels limit the block’stilting action. The block remains flatand distribute the load evenly along itsgliding surface GLIDE BLOCKSGlide blocks in the base frameGlide blocks have a steel reinforcement through centre of copolymer plastic allowing for a strong yet durable and smooth operationGLIDE BLOCKS Glide blocks in the runwayContained glide block tracks, on the runway •Increased bearing support area•Linear glide movement•Longer life cycle GLIDE BLOCKSGlide blocks have a steel reinforcement through centre of copolymer plastic allowing for a strong yetdurable and smooth operationGLIDE BLOCKS Cutaway view of the glide block. Notice the steel reinforcement •Reduces torsional load effect •Minimizes radial stress •Prolonged life cycle | reduced maintenance •Superior than non-reinforced glide blocksGLIDE BLOCKSPIVOT PINSChrome plated pins on all pivot points that run on fiber wound self lubricated bushingsCHROME SURFACE•Last longer than other materials •Does not produce noise under loads •Requires no maintenanceHYDRAULICSTwo (2) high quality lifting cylinders are located in each scissor assembly four total The lift has 4 cylinders, 2 masters and 2 slaves for better synchronization and equalizationSAFETY LOCKSSafety lock mechanism improved with a 22mm thick both top and bottom lock bars from original 19mm and has 18 secure lock positions through full lift height Laser cut and side-to-side matched locks, ensure a level platform at all heightsSAFETY VALVEHydraulic safety valves (velocity fuses) installed on both primary cylinders allowing added safety in the event of a leaking hydraulic hose (burst)The safety valve prevents the lift from rapidly descending in the case of a catastrophic failure or human errorSURFACE FINISHStructure has a durable powder coat finish capable of withstanding the elements for many yearsSafety release button, raise/lower buttons‘E’ stop and if equipped with Lights and Locks, lock/unlock switch for locking mechanism on turn plates and slip platesAll mounted so the operator has a safe position to view lift function FEATURES AND ENHANCEMENTSCONTROLS ON CONSOLE7K ROLLING JACK BEAM •Rolling jacks glide on rails via four rollers •Air over hydraulic ensure a smooth and fast action•Lower to deck height, providing ample vehicle clearance even for those lowered vehicles •One front and one rear jack•Two position locks7K ROLLING JACK BEAM WITH 3” AND 6” ADAPTERS3” ADAPTERS6” ADAPTERSNEW MODELS AVAILABLEShort Bay, Surface Mount Part Number EELR783AShort Bay, Flush Mount Part Number EELR784A Standard Bay, Surface Mount with Locks & Lights Part Number EELR789A Standard Bay, Flush Mount with Locks & Lights Part Number EELR790AFor more product information visit us at 。

扭矩仪传感器使用方法

扭矩仪传感器使用方法扭矩仪和传感器是广泛应用于工业生产和实验室测试领域的设备，用于测量扭力和力的大小。

下面将详细介绍它们的使用方法。

一、扭矩仪的使用方法：1.校准扭矩仪：在使用扭矩仪之前，需要进行校准以确保测量结果的准确性。

校准方法一般包括零校准和全量程校准两个步骤。

零校准是将扭矩仪置于无载荷状态下，将指示器调整到零位；全量程校准是加载一定的扭矩到扭矩仪上，并调整指示器使其与实际扭矩值相等。

2.安装扭矩仪：将扭矩仪安装到需要测量扭力的设备上。

通常扭矩仪有两个夹持板，分别夹持住被测的旋转轴和被测的扭矩输出轴。

确保扭矩仪的夹持板牢固地固定在两个轴上。

3.设置扭矩仪：根据被测设备的特点和需求，设置扭矩仪的转矩范围和单位。

转矩范围是指扭矩仪所能测量的最大和最小扭矩值，单位可以选择牛顿米、磅英尺等。

4.测量扭矩：连接扭矩仪与电源，启动仪器，并将旋转轴转动到被测扭矩加载时。

在加载到预设的扭矩值时，读取扭矩仪上的指示值。

如果需要连续测量，可以将扭矩仪连接到计算机或数据采集设备上，以便实时记录扭矩数据。

5.数据处理与分析：将扭矩测量结果导出到计算机，并进行数据处理与分析。

常见的处理方法包括计算平均值、最大值和最小值，绘制扭矩曲线等。

二、传感器的使用方法：1.安装传感器：将传感器安装到被测对象上。

传感器的选择和安装位置需根据被测信号的特点和测量要求来确定。

在安装传感器时，需要确保传感器与被测对象之间的接触充分、固定可靠。

2.连接传感器：将传感器与数据采集设备或信号调理器相连。

传感器的输出信号通常为模拟信号，需要按照所采集设备的接口要求进行相应的连接。

3.校准传感器：通过校准来确定传感器的灵敏度和线性度等参数。

校准一般通过加载标准信号或比较测量方法来进行。

校准结果将用于后续的数据处理和分析。

4.数据采集与记录：启动数据采集设备，开始对传感器输出信号进行采集和记录。

根据需要，可以选择不同的采集频率和持续时间，以获得所需的数据。

SNAP-ON RT系列水力扭力杆说明书

RT S eriesH ydraulic torque wrenchUsed worldwide due to its powerful torque output and long-lasting tool performance.SPLINED SQUARE DRIVEThe RT Series splined square drive distributes load evenly through the drive components, providing full heavy-duty transmission of force. Direct Hex Drives and Hex Adapters are available.SPRING-LOADED SHROUD Spring loaded shroud absorbs energy during operation.EXTERNAL DISENGAGEMENT LEVERThese external disengagement levers make it easy to remove the tool from the application.Our vision for the RT Series hydraulic torque wrench is a simple one: create a hydraulic torque wrench with legendary durability for the most demanding applications. The RT series is a hy-draulic torque wrench that will deliver superior performance and accuracy over a longer tool life.From design, to manufacturing and calibration, the RT Series is a purpose-built bolting machine. It stands second to none.RT SERIESSQUARE DRIVEHYDRAULIC TORQUE WRENCHHIGH STRENGTH STEEL BOOT The reaction arm boot comes standard.Copper boot also available.MONOBLOC ALUMINUM HOUSING A single block of aircraft quality aluminum alloy is used to produce the RT Series housing. This allows the tool to produce massive amounts of torque, while havingan amazing power-to-weight ratio.MULTI-AXIS SWIVELGreater range of movement on multiple axis allows the hose to move easier compared tosingle axis swivels.SPLINED REACTION ARMSplined reaction arm makes the tool more compact and allows the reaction arm to beadjusted for maximum safety.RT with Standard Reaction Arm RT Safety HandleAlco Reaction ArmSteel Reaction SleeveSteel Reaction Sleeve with foot CAM-style Reaction Arm Extended Reaction Arm Sliding Reaction Arm Direct Hex DriveInsert Bit AdapterModelDimensionsL1L2H1H2Radius W1W2inmminmminmminmminmminmminmmRT-0.5 3.1581 4.87125 2.3560.5 3.62930.5213.5 1.333.5 1.9750.5RT-01 4.681207.13183 3.5290.5 4.751220.923 1.9550 2.7671RT-03 6.041559.24237 4.681206.08156 1.2833 2.5966.5 3.7295.5RT-057.2118511.23288 5.63144.57.05181 1.4437 3.1280 4.9126RT-087.8520212.49321 6.42164.68.4213.36 1.6241 3.4888 4.95126RT-10923213.93577.21869.3239 1.8748 3.9100 5.5142.5RT-2010.225916.554208.52169.9251 2.1755.1 4.7119 6.7170RT-251231018.44739.123411282 2.3761 5.21347.4191RT-5015.239023.961511.429413.434430.8796.51678.9228ModelSquare DriveTorqueWeightOrdering No.ft. lb.NminminmaxminmaxlbkgRT-0.51/2 55397755380.80.48434 2010 00RT-013/4 20013402711817 3.8 1.98434 2010 02RT-03 1 480323065143797.8 3.98434 2010 05RT-051-1/2 835559011327578157.58434 2010 09RT-081-1/2 120080001627108452311.58434 2010 13RT-101-1/2 17551152023791561726.813.48434 2010 16RT-202-1/2 29601976040132678736188434 2010 20RT-252-1/2 39602589053683509662318434 2010 25RT-502-1/2787552500106757116996488434 2010 29The RT comes with the standard reaction arm, great for many common applications.The RT Series comes standard with asquare drive, use with a socket.Designs and specifications are subject to change without notice or obligation. Read all safety instructions in the manual before usage.STANDARD SETUPALCO ARMSTEEL SLEEVECAM STYLE ARMEXT ARM SLIDING REACTION ARMSAFETY HANDLESTEEL SLEEVE W/FOOTSTD= Standard EXT=ExtendedDescriptionOrdering No.RT0.5-EXT 4222 2126 82RT01-EXT 8434 2056 92RT03-EXT 8434 2057 12RT05-EXT 8434 2057 34RT08-EXT 8434 2140 42RT10-EXT8434 2140 66DescriptionOrdering No.RT-01 SLIDING EXT 8434 2057 33RT-01 SLIDING STD 8434 2150 95RT-03 SLIDING EXT 8434 2150 37RT-03 SLIDING STD 8434 2150 30RT-05 SLIDING EXT 8434 2150 36RT-05 SLIDING STD 8434 2150 35RT-08 SLIDING EXT 8434 2150 32RT-08 SLIDING STD8434 2150 31DescriptionOrdering No.RT-10 SLIDING EXT 8434 2150 34RT-10 SLIDING STD 8434 2150 33RT20 SLIDING EXT 8434 2150 90RT20 SLIDING STD 8434 2150 89RT25 SLIDING EXT 8434 2150 92RT25 SLIDING STD 8434 2150 91RT50 SLIDING EXT 8434 2150 94RT50 SLIDING STD8434 2150 93Description Ordering No.RT0.5-ALC 4222 2126 76RT01-ALC 4222 2102 64RT03-ALC 8434 2057 10RT05-ALC 8434 2139 88RT08-ALC 8434 2140 36RT10-ALC8434 2140 60Description Ordering No.RT0.5-SSLV 4222 2126 88RT01-SSLV 8434 2057 08RT03-SSLV 8434 2057 32RT05-SSLV 8434 2140 30RT08-SSLV 8434 2140 51RT10-SSLV8434 2140 90Description Ordering No.RT03-CAM ARM 4222 2130 12RT05-3 CAM 4222 2130 57RT05-03-CAM4222 2130 48DescriptionOrdering No.HANDLE KIT RT0.5, RT18434 2170 34HANDLE KIT RT3, RT58434 2170 33HANDLE KIT RT8, RT108434 2170 32Description Ordering No.RT01-SSLVF 8434 2057 09RT03-SLVF4222 2130 21ACCESSORIESDIRECT HEX DRIVEINSERT BIT ADAPTERDescriptionOrdering No.Hex Holder Sq Dr 3/4"-7/8"8434 2129 59Hex Holder Sq Dr 1/2"-1/2"8434 2056 58Hex Holder Sq Dr 1/2"-7/8"8434 2056 60Hex Holder Sq Dr 1 1/2"-1 3/4"8434 2129 62Hex Holder Sq Dr 1 1/2"-1 1/4"8434 2129 65Hex Holder Sq Dr 1"-1 1/4"8434 2129 68Hex Holder Sq Dr 1"-7/8"8434 2056 62 Hex Size 10MM 8434 2054 24 Hex Size 12MM 8434 2054 26 Hex Size 14MM 8434 2054 30 Hex Size 17MM 8434 2054 32 Hex Size 19MM 8434 2054 34 Hex Size 22MM 8434 2054 36 Hex Size 24MM 8434 2054 38 Hex Size 27MM8434 2123 32DescriptionOrdering No.Hex Size 1 1/16"8434 2124 10 Hex Size 1 1/4"8434 2050 14 Hex Size 1 1/8"8434 2050 16 Hex Size 1 1/2"8434 2050 32 Hex Size 1 3/4"8434 2050 34 Hex Size 1 3/8"8434 2050 36 Hex Size 1 5/8"8434 2050 38 Hex Size 1"-12pt 8434 2126 86 Hex Size 1/2"8434 2054 22 Hex Size 13/16"8434 2054 28 Hex Size 3/4"8434 2054 40 Hex Size 5/8"8434 2054 42 Hex Size 7/8"8434 2054 44 Hex Size 9/16"8434 2054 46DescriptionOrdering No.RT0.5-HX-10MM 8434 2138 44RT0.5-HX-12MM 8434 2138 47RT0.5-HX-14MM 8434 2138 50RT0.5-HX-16MM 8434 2138 53RT0.5-HX-17MM 8434 2138 56RT0.5-HX-19MM 8434 2138 62RT0.5-HX-22MM 8434 2138 68RT0.5-HX-24MM 8434 2101 71RT01-HX-0108434 2138 71RT01-HX-0128434 2138 74RT01-HX-0148434 2138 77RT01-HX-17MM8434 2056 96DescriptionOrdering No.RT01-HX-19MM 8434 2056 98RT01-HX-22MM 8434 2057 02RT01-HX-24MM 8434 2057 04RT01-HX-27MM 8434 2057 06RT03-HX-0108434 2057 14RT03-HX-0128434 2057 16RT03-HX-0148434 2057 18RT03-HX-19MM 8434 2057 22RT03-HX-19MM-EXT 8434 2139 40RT03-HX-22MM 8434 2057 24RT03-HX-22MM-EXT 8434 2116 22RT03-HX-24MM 8434 2057 26RT03-HX-24MM-EXT8434 2116 25COMMITTED TO SUSTAINABLE PRODUCTIVITYWe stand by our responsibilities towards our customers, towards the environment and the people around us. Wemake performance stand the test of time. T his is what we call - Sustainable Productivity.9833 2015 01 2015:06 © 2015, A t l a s C o p c o . A l l r i g h t s r e s e r v e d .。

Snap-on Equipment 车轮对齐器产品说明书

PORTABLE IMAGEWHEEL ALIGNERParts ManualTable of ContentsAlignEr ASSEmbly (2)CAbinET ASSEmbly (3)pC in A box ASSEmbly (4)poD ASSEmbly (5)WhEEl ClAmp ASSEmby (6)TArgET ASSEmbly SErViCE (8)WAP (9)CAlibrATion hArDWArE (10)1AlignEr ASSEmblyEEWA557Al - JbC / EEWA717Al - hofmann (north America)EEWA555Al - JbC / EEWA719Al - hofmann (Europe)QTy pArTnumbEr DESCripTion1 EAl0392J66A DECAl-JbC 9 in1 EAl0343J05A DECAl-hoFmAnn1 EAl0392J78A DECAl - gEolinEr 5501 EAl0392J76A DECAl-priSm ConSolE El1 EAK0268J05A prinTEr KiT-uSb1 3-03506A prinTEr-Color inKJET1 00088910000 prinTEr-pApEr 11460301 6-02422b6 CAblE-uSb 6' A mAlE To b mAlE1 5-10426A1 TApE-hooK VElCro #881 5-10426A2 TApE-loop VElCro #10001 00089209000 CorD-poWEr ADApTEr 121 88931000 poWEr CorD/lAbEl ASS'y 115V1 EAl0392J61A pAD-mouSE1 EAK0277J82A liT pACK-gEnEriC1 96000 DEprESSor ASS'y-pEDAl1 55502000 ClAmp ASS'y-WhEEl STEEring1 EAA0337J81D CAbinET-El bASiC JbC1 EAA0353J09b CAbinET-El bASiC hoFmAnn1 EAK0289J59A moniTor-17” lCD1 EAA0353J93A pC ASSy-gEnEriC - priSm JbC / hoFmAnn 1 3-40426CF1 SFTWr-KEy DiSK,JbC1 3-40626CF1 SFTWr-KEy DiSK, hoF1 EAK0289J22A KiT-ClAmp brACKET (4)2 EAC0090J82A ChoCK-WhEElEAK0289J78A KiT - mouSE / KEyboArD2-02639A bluETooTh rADio - uSbEAS2119J03A moniTor - mounTing brACKET23CAbinET ASSEmblyEAA0337J81DEAA0353J09b2 8-28839A CASTor-SWiVEl 4"2 8-28939A CASTor-SWiVEl 4" WiTh brAKE1 111245 lAbEl-CAuTion, ElECTriCAl1 8-11133A hAnDlE- pC/prinTEr ShElF DoorS 1 EAS2091J94A Door WlDmT pC ShElF4pC in A box ASSEmbly EAA0353J93Au2-18451AFuSE-5A Slo blo 86164000lAbEl-FuSE 86465000lAbEl-WArning ShoCK 111245000lAbEl-CAuTion ElECT EAl0345p51AlAbEl-FuSE 5A EAl0345p54AlAbEl-ElECTriCAl WArning143526iTEmrEQD pArT no DESCripTion 11 EAC0090J40A bumpEr - CoVEr. CAmErA 21 EAC0090J41A bumpEr - CroSS ToE 31 EAC0090J44A piVoT bumpEr 42 EAm0054J55A CW - ouTSiDE,51 EAC0090J81A bumpEr loWEr bATTEry 6 1 EAK0289J46A bATTEry pACK SVC KiTEAK0289J89Au - right hand JC6Sym rEQD pArT no DESCripTion1 1 1-02612A m8 Thumb SCrEW2 6 1-20077A rETAin - ring, WC3 4 1-34806A SCrEW - FlAT phm, m4 x 25mm4 3 1-53110A SCrEW-SET m3 x .5 x 6mm, Cup pT.5 1 1-55909A SCrEW - ShC, m8 x 35mm6 1 EAC0055J46A Knob-ShAFT ClAmp7 2 EAC0090J50A brACKET - guiDE roD8 2 EAC0090J52A CoVEr - holDEr, buShing9 1 EAC0090J56A Knob - CAST, WC10 1 EAm0054J26A buShing - WC, righT11 1 EAm0054J27A buShing - WC, lEFT12 1 EAm0054J39A brACKET - uppEr, long13 1 EAm0054J41A brACKET - long. loWEr, WC14 1 EAm0054J58A roD - lEAD SCrEW mACh. - Eur1 EAm0054J49A roD - lEAD SCrEW mACh. - nA15 1 EAm0054J59A roD - guiDE, mACh., Eur1 EAC0090J58A roD - guiDE, mACh., nA16 2 1-47709A ShCS - m10 x 20mm17 2 1-5741 WAShEr, plAin 3/818 2 EAS2105J11A WAShEr - SpACEr, WC* 1 EAK0289J40A STAbiliZEr KiT* 2 EAK0222J40A DuAl WhEEl ADApTEr* 2 EAK0289J85A Drop DoWn ADApTEr* 1 EAK0268J41A WhEEl grAbbEr KiT (4 grAbbErS) noT pArT oF WhEElClAmp ASSEmbly1 1-08584A bungEE CorD (noT pArT oF WhEEl ClAmp ASSEmbly) * iTEmS ArE opTionS For WhEEl ClAmpS78WAPEAK0289J45A - WAp SErViCE KiT (AlignEr Sn Eb - KC)EAW0235J70A ChArging CAblE ASSEmbly2-50166A - poWEr Supply (briCK TypE)noTE: no FiElD SErViCE pArTS inSiDE WirElESS ACCESS ASSEmbly2-02639A - bT rADio (AlignEr Sn lC Thru CurrEnT)2-55466A - poWEr Supply (WAll WArT)2-55566A - y-CAblE2-55666A - uS rECEpTAClE2-55766A - uK rECETAClE2-55866A - Eu rECETAClE2-55966A - Au rECETAClE91011notice: The information contained in this document is subject to change without notice. Snapon Equipment makes no warranty with regard to this material. Snapon Equipment shall not be liable for errors contained herein or for incidental consequential damages in connection with furnishings, performance, or use of this material.This document contains proprietary information which is protected by copyright and patents. All rights are re-served. no part of this document may be photocopied, reproduced, or translated without prior written consent TEEWA557A3 rev E 10/2010...rjh printed in the u.S.A.。