九阳豆浆机 DJ13B-C86 使用说明书

合集下载

九阳豆浆机dj13bd68s说明书.doc

九阳豆浆机dj13bd68s说明书九阳豆浆机使用说明书(共3篇)九阳豆浆机使用说明书九阳豆浆机使用说明书九阳豆浆机是一款采用专利精磨技术的豆浆机，在使用方面也很便利。

下面品橙X详解介绍下九阳豆浆机的使用方法以及怎样才能做出优质豆浆：一、九阳豆浆机使用方法：首先，按照杯体上标的上、下刻度线加水至上下水位线之间，把泡好的黄豆装至X罩容积的一半左右，再把机头部分轻放于杯体上，插好电源，如果是多功能豆浆机，还要按动启动键或配合其它按键编制相应工作程序，机器在微电脑控制下才开始工作，直至把豆浆做熟，自动断电，声光报警。

豆浆倒出后，旋下X罩倒出豆渣，及时清洗，加热管和防溢电极在水管上一冲，用擦布擦净即可。

使用九阳豆浆机，在家自制鲜豆浆就这么简单。

二、怎样才能做出优质豆浆1.家用豆浆机要做出香浓好豆浆，豆浆第一次煮沸触碰防溢电极时的最佳温度为98℃。

因为若低于98℃，则可能煮不熟，熬煮不出好豆浆的那种粘度和浓香味。

豆浆第一次煮沸能否达到98℃，与X罩底孔的大小和豆子粉碎后浆沫的多少密切相关。

因为X罩底孔必须保持一个科学的大小，才能使做出的豆浆泡沫适中。

底孔太大或太小都会产生太多的浆沫，造成浆沫和防溢电极之间的距离短，浆沫受热上升，很快就触碰到防溢电极停止加热，而温度则达不到98℃；反之浆沫较少时，浆沫和防溢电极之间有一个较长的距离，受热上升时，有足够的受热时间，从而能顺利达到98℃。

2.要想做出优质豆浆，必须在豆浆第一次煮沸达到98℃的基础上再延煮4-5分钟，从而将豆浆彻底煮熟煮透，浓香四溢。

延煮时间太短则煮不熟，太长则易使部分营养素挥发掉，是浪费，豆浆也不香。

3.豆浆是否浓香与豆量以及粉碎程度有关。

当水量一定时，应保持一个合理的豆量。

豆量少，则浓度不高；豆量太多，浓度也不会再增加，因为豆子太多了，就会影响粉碎程度，豆子不能完全粉碎，未被粉碎的部分就浪费了，并不能增加浓度。

因此，应保持一个合理的豆量，既能做出高浓度的豆浆，又不至于浪费。

(完整word版)九阳豆浆机使用说明书英译版(by May)

九阳豆浆机使用说明书（英文版）JYD-P11S81/P13S82, JYD-C10P86/C12P87翻译by: May 翻译时间：2011年（具体时间忘记了）注：直接翻译的九阳官网上中文版本的使用说明书翻译来由：去年意大利老大突然给了份九阳豆浆机的中文说明书，说他们家买了台但是他和他太太都没办法看懂中文，于是我就纯中式翻译给简易翻了下。

不觉得有多好，但是好歹费了脑细胞了就上传到百度文库了，上传后一直没看的，今天无意中才发现原来没上传成功，理由是“可能侵犯他们版权”。

今天再重新上传一次，希望可以成功2012年4月18日星期三16:33This mark means special warning or reminding, please note that when usedX this mark means the wrong using, be careful.1. Do not wet the machine socket, if watering, must be dried before using.2. Clean timely of the cup body, anti-overflow electrode and temperature sensor.3. Do not plug the power cord and press the start-key during the machine rearworking time or after it finished, or the soybean milk maybe overflow or cause warning alarm.4. Do not forget to install the grinding grain device, or the milk will overflow in theworking process and may cause scald.5. Please place the soybean, rice, etc. on the bottom of the cup body as even aspossible.6. Pour milk should hold hands and then remove the head or nose first down milk inorder to avoid slippage head injury.7. Place the machine out of children reach when it works.8. Clean the grain grinding device timely.9. Cool the grain grinding device with cold water first when disassemble the machine,to avoid excessive force and scratched hands.10, this machine apply high speed motor, the unsteady voice during the working process is normal.11, Keep a certain distance with socket and other charged when it works, and keep it away from flammable materials machine work, and make sure the plug is within reach and the ground wire is good.12, If power down in the course of machine working process(especially in the beating late completion), please do not press the function keys, or that will make the heater paste tubes, blowing or warning alarm failure.13, if the power cord is damaged, you have to buy a new one in Joyoung after-sales for changing. 14. It needs more than 20 minutes work, if the added water temperature is low.15. After a using time, the lower cover may be dyed, that is normal, staining does notaffect consumption and no harm to health.After completely cleaning, do not put the Heading into the cup body, and to avoid odors caused by the high temperature, please place it on the ventilation condition.1. Heading: this machine main parts, includes motor, computer board, etc.2. Operation Key: chose and press the function key, it works and the light will turn on.3. Outlet/Socket: use for connecting the power wire.4. Micro switch post: safety device, lift the hading, blackout automatically5. Anti-overflow electrode: use for detecting and preventing the soybeanmilk ebullition and overflow.6. Temperature sensor: use for detecting the water temperature, machineworks when the temperature reaches the setting figure.7. Lower cover: made by hi-quality material comforted to the food hygiene requirements, use for setting the main parts, etc.8. Grain Grinding device: made by hi-quality stainless steel comforted to the food hygiene requirements, use for grinding all kinds of materials.9. Blade: made by hi-quality stainless steel, use for crushing all kinds ofmaterials.10. Cup body: comforted to the food hygiene requirements.11. Level mark: water level mark. When making soybean milk or all kinds ofother drinks, you should put the soybean or other materials in the cup body and keep the water lies between the marks.12. Heater: use for heating the soybean milk or other drinks.13. Vent hold: use for exhausting, and keep it dry when washing.Chapter III UsageI. Making the soybean milk1. Measure the food material: take use of the measure cup.Note: please soak into the clear water after washing when making soybean milk or other milks (usually Northern area for 8-16 hours soaking time in spring and autumn, 6-10 hours in summer and 10-16 hours in winter; Southern area for 5-6 hours in spring and summer, 8-9 hours in Autumn and winter), and making the green bean congee, the green bean do not need to soak.2. Add the food materials into the cup body: please put the food materials or the soaked bean into the cup body after washing.3. Add water: keep the water lies between the marks (the machine will not work if there is no water or the water is not enough)4. Install the Grain Grinding device: install follow the indicated arrow in the machine, and check it after installation to make sure the well installed.Special note: do not forget to install the grain grinding device.5. Making soybean milk: place the heading into the cup body correctly, connect the power wire, and press the function key.6. Soybean milk prepared: After several times beating and boiled as set, the machine stop working, and the alarm raise, pointing out the soybean silk is ok. Turn down the power; you can enjoy the milk then.7. Filter milkThis machine made milk, the whole syrup also boiled together with slag for the better nutrition. You could use the filter according to your own preferences and filter the milk for a better taste.(Note: This filtering is limited to making use of the whole bean soy milk).II. Making the other cold drink (e.g. Banana milk)1. Choose the food materials: clean the banana (or other fruit or vegetables), cut into small piece and take 3 cups (measuring cup).2. Add food materials: put the measured food materials into the cup body3. Add cold water and milk: put the mixture of milk and water (2:1 ratio) into the cupbody, and keep the liquid lies between the marks.4. Install the Grain Grinding device: install follow the indicated arrow in the machine,and check it after installation to make sure the well installed.Special note: do not forget to install the grain grinding device.5. Making the cold drinking: place the heading into the cup body correctly, connect the power wire, and press the function key.6. Drinking prepared: After several times beating and boiled as set, the machine stop working, and the alarm raise, pointing out the drinking is ok. Turn down the power; you can enjoy the drinking then.Special notice: for repetitious use, the interval time is at least 10 minutes.III. Operation Key special usage1. Turn on the power, the machine will give a “toot" hi nt voice, and the indicator light will turn on.2. Press other key does not work, when the machine is working.3. If you press the wrong key, please turn off the power and press again. (Note: the wrong key may affect the taste of the drinking)IV. Special usagePlease follow the instructions to operate, or it may affect the taste. Chapter IV MaintenanceCleaning: please clean timely after using. (Note: when unloading the Grain Grinding Device, please cold it with cool water)1. Heading: gently wash out the lower cover adhesive milk or other things, keep the heading away from water, keep it dry (or may cause the short circuit)2. Grain Grinding Device: clean carefully with a cleaning brush or a block, and make sure the neat to avoid the odor.3. Heater: clean with a cleaning brush or a block to avoid the next time paste.4. Cup Body: clean carefully with a cleaning brush or a block, and wash out with clear water.5. Preservation: put the machine in dry, ventilated place.6. Note: Do not drink the milk without total normal process.Chapter V Production Safety IndexChapter VI Adopt StandardEnterprise Standard: Q/01YJY002-2007Chapter VII Malfunction AnalysisThe cup means the measure cup of the machineThe cup means the measure cup of the machineJoyoung operation instructionType: JYD-P11S81/P13S82, JYD-C10P86/C12P87。

九阳豆浆机的使用方法

九阳豆浆机的使用方法九阳豆浆机简介九阳公司在健康厨房电器领域不断拓展，新产品层出不穷，主要产品涵盖了豆浆机电压力煲、电磁炉、料理机、榨汁机、紫砂煲、开水煲、电饭煲、油烟机、燃气灶、消毒柜、热水器等十二大系列两百多个型号。

作为豆浆机行业的开创者和领导者，九阳持续引领新兴健康厨房电器的技术进步和发展，还积极把健康产业向上游延伸，开发了专供于酒店、写字楼的“原磨豆浆”商用豆浆机和出品自东北肥沃黑土的非转基因优质大豆“阳光豆坊”豆浆原料。

2011年初，九阳斥巨资进军净水领域，推出九阳“冰蓝”系列净水机产品，全力打造“好机+好豆+好水=好豆浆”的健康产业链条。

2012年，九阳成立大厨电事业部，“净吸王”油烟机、“爆炒王”燃气灶等系列产品上市，由此带来九阳健康产业的又一次升级。

九阳豆浆机的优势1、全自动控制，一键启动更轻松只需要轻轻一按键，十几分钟就可自动做成香浓可口的熟豆浆2、多功能易清洗五谷、全豆、果蔬各种花色豆浆及玉米汁随心制作，豆浆好做更好洗3、文火熬煮，熬得透、喝着香4、智能不粘，不粘不糊、易清洗5、仿生造型，人性化设计，美观舒适6、六大智能安全保护，使用更安全，更舒适九阳豆浆机使用方法1、浸泡豆子用随机所配干豆量杯按2/3刻度线盛出干豆洗净后泡入清水（浸泡时间为春秋季8-16小时，夏季6-10小时，冬季10-16小时。

）特别提示：浸泡豆子前请先将豆子清洗洁净。

2、杯体参加豆子和米用于豆量杯依照2/3刻度量取大米，连同浸泡好的豆子洗洁净后直接放入杯体内。

3、杯体内参加清水请将水加至上、下水位线之间。

（本机具有无水防干烧功用，如杯体内无水或水位过低，机器不会工作，以保证运用平安）。

九阳豆浆机使用说明书(共3篇)

篇一：九阳豆浆机使用说明书九阳豆浆机使用说明书九阳豆浆机是一款采用专利精磨技术的豆浆机，在使用方面也很便利。

下面品橙网详解介绍下九阳豆浆机的使用方法以及怎样才能做出优质豆浆：一、九阳豆浆机使用方法：首先，按照杯体上标的上、下刻度线加水至上下水位线之间，把泡好的黄豆装至网罩容积的一半左右，再把机头部分轻放于杯体上，插好电源，如果是多功能豆浆机，还要按动启动键或配合其它按键编制相应工作程序，机器在微电脑控制下才开始工作，直至把豆浆做熟，自动断电，声光报警。

豆浆倒出后，旋下网罩倒出豆渣，及时清洗，加热管和防溢电极在水管上一冲，用擦布擦净即可。

使用九阳豆浆机，在家自制鲜豆浆就这么简单。

二、怎样才能做出优质豆浆1.家用豆浆机要做出香浓好豆浆，豆浆第一次煮沸触碰防溢电极时的最佳温度为98℃。

因为若低于98℃，则可能煮不熟，熬煮不出好豆浆的那种粘度和浓香味。

豆浆第一次煮沸能否达到98℃，与网罩底孔的大小和豆子粉碎后浆沫的多少密切相关。

因为网罩底孔必须保持一个科学的大小，才能使做出的豆浆泡沫适中。