电控柜出厂检验报告范本

合集下载

低压开关柜出厂检验报告

铭牌应坚固、耐久，其位置应在易于看到的地方，且标识正确、清晰
随机文件（如图纸、说明书、合格证等）应齐全
通电操作试验，所有元件应正确动作，线路无误。操作5次，动作可靠无异常现象，试验结果应符合设计要求。
结论：检验员：日期
前门锁与地之间
后上门锁与地之间
后下门锁与地之间
刀开关手柄与地之间
断路器框架与地之间
熔断器安装支架与地之间
柜体与地之间
电气间隙
爬电距离
不同极性的裸导线之间以及它们与外壳之间
≥10mm
≥12.5mm
壳防护等级
φ2.5试具不得通过，符合IP30要求
一致性查
电器元件结构等均应与型式试验产品相一致
布线、操作性能和功能
2.检查导线、母线截面积是否符合要求，连接接触良好
3.检查装置中连接导线是否采用铜芯多股绝缘导线，且接线正确无误
外接导线端子
端子的数量、类型、标志、允许外接铜导线的截面积应符合图纸和工艺文件要求。
机械操作试验
对机械操作的部件操作5次无异常现象出现，机构灵活动作可靠，应无卡阻、有效
介电强度试验
绝缘电阻验证：相间及相导体与裸露导电部件之间>1000Ω/V
1、主电路的所有带电部分（包括连接到主电路上的控制电路和辅助电路）连接在一起与外露可导电部分之间施压1890V，施压时间1S，应无击穿闪络现象；
2、主电路不同电位的每个带电部分和不同电位其他带电部分与连接在一起的外露导电部分之间施压1890V，施压时间1S，应无击穿闪络现象
3、带电部件与用金属箔裹缠的绝缘操作手柄之间(试验时，框架不应接地，也不应与其他电路连接)施压2835V，施压时间1S，应无击穿闪络现象
低压配电柜确认检验记录

电气控制柜出厂检验报告单

b）仪表门锁与地
5
通电试验
按原理图、功能通电试验
通电试验台
本产品出厂检验结论：检验日期：
检验员：
电气控制柜（箱）出厂检验报告单
NO.
产品名称：型号规格：
产品编号：检验依据：
序
号
检测项目与技术要求
检验方法
检测结果
1
般检查
面板平整、焊接均匀牢靠、无明显变形、涂层完好
目测
兀件安装牛固
二次配线连接牢固、端头有标志、相序排列正确
接地等标志符合要求。
2
尺寸检查
门开启角度＞90度，灵活开启
目测卷尺
电气间隙：》10mm
爬电距离：》15mm
3
介电试验
导电部件与地之间、导电部件之间
2500V 1S无闪络或击穿
控制回路与地之间
2000V 1S无闪络或击穿
绝缘手柄对地
3750V 1S无闪络或击穿
CC2672型
耐压测试仪
4
保护电路连续性试验
抽测接地电阻（电阻应w100mQ）a）开关支架与地

配电柜出厂检验报告

配电柜出厂检验报告
电控柜验收报告
项目名称：编号：
柜体名称
柜体规格
柜体类型
柜体数量
项目
检验项目及技术要求
检验结果
备注
绝缘
测试
1、相间电阻、及相线与中线电阻应大于500MΩ。
合格/不合格
耐压
测试
1、主电路带电部件与地（框架）之间，2500V在5秒无击穿、无闪络现象。
合格/不合格
2、主电路母排各相之间，2500V5秒无击穿、无闪络。主回路导线之间，750V5秒无击穿、无闪络，二次回路500V5秒无击穿、无闪络。
合格/不合格
保护电路的连续性
1、主接地线与门（箱体）之间的的连续性试验，接地电阻<Ω，试验电流为》10A
合格/不合格
2、主接地线与柜体裸露导电部件之间，接地电阻<Ω，试验电流为》10A。
合格/不合格
通电
测试
1、按装置的电气原理图要求进行模拟动作试验，试验结果应符合要求，5次以上均正常动作。
合格/不合格
质检综合结论：
检验部门：
质检人：
检验日期：
性能
参数
1、变频器、软启动器、热继电器、时间继电、仪表等参数必须按所需功能设定。
合格/不合格
品牌检验
1、元件器品牌型号应与图纸或者报价单一致。
合格/不合格
包
装
1、编号管、图纸、安装附件应齐全。
合格/不合格
2、柜面、显示部分或突出部分应有保护措施。
合格/不合格
3、包装应有方向说明及注意事项。
合格/不合格
2、安装置的电气原理图要求进行故障模拟试验，其故障信号和报警指示应正确。
合格/不合格

电气控制柜出厂检验报告

电气控制柜出厂检验报告
摘要
本报告对电气控制柜在出厂前进行了详细检验。

检验包括了外观检查、电气性能测试以及安全功能验证。

通过本次检验，确认该电气控制柜符合相关技术标准和产品要求，并且能够安全、正常地运行。

1. 检验对象
- 产品名称: 电气控制柜
- 型号: [填写型号]
- 出厂编号: [填写编号]
2. 检验依据
- 相关技术标准及规范
- 产品要求和规格书
3. 检验内容及结果
3.1 外观检查
- 外观完好无损，无明显变形、破损和划痕。

- 所有控制按钮、指示灯和显示屏等操作元件正常牢固，标志清晰可辨。

- 接线端子、连接器和接口无松动、发热等异常情况。

- 控制柜内部无异物，线束整齐，布线良好。

3.2 电气性能测试
- 连接电源后，控制柜能够正常启动。

- 所有开关、控制器和继电器等电器元件的工作正常。

- 电气参数测量值符合技术标准要求。

3.3 安全功能验证
- 安全保护装置有效，能够及时停机或报警。

- 防护措施完善，无电击和触摸危险。

- 紧急停止按钮可正常工作，能够迅速切断电源。

4. 检验结论
根据以上检验内容及结果，确认该电气控制柜在出厂前通过了各项检验，达到了相关技术标准和产品要求。

预计这台电气控制柜能够安全、可靠地使用，对使用者和设备起到了有效的保护作用。

5. 检验人员
检验人员姓名：[填写姓名]
检验日期：[填写日期]
附注
[在此添加任何相关的附注、异常情况说明等信息]。

控制柜出厂检验报告

控制柜出厂检验报告一、报告概述本报告旨在记录对控制柜进行出厂检验的结果和评估，以确保控制柜的质量符合相关标准和要求。

本报告包含控制柜的基本信息、检验结果、评价和建议。

二、控制柜基本信息1. 产品名称：控制柜2. 型号：XXXXXXXXX3. 生产厂家：XXXXXXXXX4. 出厂日期：XXXX年XX月XX日5. 出厂编号：XXXXXXXXX三、检验结果1. 外观检查在外观检查中，控制柜外壳无明显变形、破损或划痕，并且无松动或过紧的零部件。

控制柜的标识清晰可见，没有涂层剥落或字迹模糊的情况。

2. 电气性能检测（1）额定电压测试：将控制柜的电源接入电压测量仪器，测试电源电压是否符合标称电压范围。

测试结果表明，控制柜的电源电压符合标称电压范围要求。

（2）断路器测试：对控制柜中的断路器进行额定电流测试，测试结果显示断路器能够正常分断额定电流，并能够防止过电流。

（3）保护装置测试：对控制柜的保护装置进行测试，保证其能够在电流过载、短路等情况下及时触发保护，保护系统的正常工作。

3. 功能测试根据控制柜的设计要求，对其功能进行测试。

测试结果显示，控制柜的各项功能均能够正常工作，包括启动、停止、调节和监测等功能。

四、评价和建议根据对控制柜的检验结果，评价如下：1. 外观检查：控制柜外观无明显变形、破损或划痕，标识清晰可见。

2. 电气性能检测：控制柜的电源电压符合标称电压范围要求，断路器能够正常分断额定电流，保护装置能够及时触发保护。

3. 功能测试：控制柜的各项功能均能够正常工作。

根据以上评价，对控制柜无需进行修理或更换，可以安全投入使用。

建议对控制柜进行定期的维护和保养，以确保其长期稳定工作。

五、结论经过对控制柜的全面检验和评估，确认该控制柜质量符合相关标准和要求。

控制柜在无需修复的情况下，可放心投入使用。

六、致谢感谢厂家提供的高质量控制柜，并感谢技术人员在检验过程中的辛勤努力。

以上为控制柜出厂检验报告的主要内容。

控制柜出厂检验报告

考验依据：GB7251.1—2005《矮压成套启闭设备战统造设备》（国标）
适用范畴：矮压统造柜、PLC统造柜等矮压电控拆置；
考验名目：睹第2页
考验论断：
所有4个机柜局部尝试通过,系统硬件尝试切合工厂FAT尝试尺度.
各项考验战考查截止标明：本产品切合国标GB7251-2005的尺度央供，切合图纸技能文献的确定，考验合格，准予出厂.
考验时间：2012年4月25日
检验员：日期：
报告考查：日期：
报告接受：日期：
江阳创捷电气设备有限公司
出厂检验报告
序号
考验名目
技能央供
检测截止
1
中瞅
元器件采用
1、元器件必须具备死产许可证，强造认证的产品必须具备认证标记；
2、元器件应切合产品电力实止尺度及安排图样额定参数的央供.
合格
元器件拆置
1、元器件拆置应坚韧稳当，应留有脚够的正弧距离战维护拆置罩所需的空间，并有防紧步伐，中部交线端子应为交线留有需要的空间.
合格
统造线配造
1、导线截里采用切合央供，布线合理，整齐好瞅；
2、线耳坚韧，无紧动局里；
3、交天呵护良佳，交天螺丝坚韧.
合格
结构、被覆层
1、产品结构尺寸战采用应切合安排央供，柜架有脚够的板滞强度；
2、漆层色泽匀称，无明隐的流痕、针孔、起泡等缺陷；
3、电镀层匀称，铅化膜完备无脱镀、收乌、霉面等缺陷.
4、检测机柜集成，即结构、交线、系统交天、风扇战照明灯完佳.
合格
2
本能尝试
静电尝试
1、根据图纸用万用表逐面检测，通断切合图纸央供.
平常
通电考查
1、按拆置的电气本理图央供，举止通电模拟动做考查，动做应精确，切合安排央供.

GGD配电柜出厂检验报告

GGD型交流低压配电控制柜出厂检验报告型号：___________________一、目的通过检查和试验，对GGD型交流低压配电柜在技术条件，范围的性能、安全性、适应性及制造、安装工艺进行验证，使产品达到出厂要求。

二、主要依据1、LEC439-1-1992低压成套开关设备第一部分2、GB7251-1-1997低压成套开关设备和控制条一部分三、试验项目1、柜体检验2、装配检验3、断路器检验4、隔离刀开关检验5、主四路无载通电操作试验6、绝缘电阻测试7、介电强度试验8、结论GGD型交流低压配电柜出厂检验报告第2页（英文版）Two regulations promulgated for implementation is in the party in power for a long time and the rule of law conditions, the implementation of comprehensive strictly strategic plan, implementation in accordance with the rules and discipline to manage the party, strengthen inner-party supervision of major initiatives. The two regulations supporting each other, the < code > adhere to a positive advocate, focusing on morality is of Party members and Party leading cadres can see, enough to get a high standard; < rule > around the party discipline, disciplinary ruler requirements, listed as "negative list, focusing on vertical gauge, draw the party organizations and Party members do not touch the" bottom line ". Here, the main from four square face two party rules of interpretation: the first part introduces two party Revised regulations the necessity and the revision process; the second part is the interpretation of the two fundamental principles of the revision of laws and regulations in the party; the third part introduces two party regulations modified the main changes and needs to grasp several key problems; the fourth part on how to grasp the implementation of the two regulations of the party. < code > and < Regulations > revised the necessity and revisedhistory of the CPC Central Committee the amendment to the Chinese Communist Party members and leading cadres honest politics several guidelines > and < Chinese Communist Party discipline and Punishment Regulations > column 1 by 2015 to strengthen party laws and regulations focus. Two party regulations revision work lasted a Years, pooling the wisdom of the whole party, ideological consensus, draw historical experience, respect for the wisdom of our predecessors, which reflects the unity of inheritance and innovation; follow the correct direction, grasp the limited goals, adhere to the party's leadership, to solve the masses of the people reflect a focus on the problem. The new revision of the < code > and < rule >, reflects the party's 18 and the eighth session of the third, the spirit of the fourth plenary session, reflecting the experience of studying and implementing the General Secretary Xi Jinping series of important speech, reflects the party's eighteen years comprehensive strictly practice. (a) revised two regulations of the party need of < the ICAC guidelines > in < in 1997 Leaders as members of the Communist Party of China clean politics certain criteria (Trial) > based on revised, the promulgation and implementation of January 2010, to strengthen the construction of the contingent of leading cadres play animportant role. But with the party to manage the party strictly administering the deepening, has not been able to fully meet the actual needs. Content is too complicated, "eight prohibition, 52 are not allowed to" hard to remember, and also difficult to put into practice; the second is concisely positive advocated by the lack of prohibited provisions excessive, no autonomy requirements; the third is banned terms and discipline law, both with the party discipline, disciplinary regulations repeat and Criminal law and other laws and regulations repeat; the fourth is to "clean" the theme is not prominent, not for the existing problems, and is narrow, only needle of county-level leading cadres above. < rule > is in 1997 < Chinese Communist Party disciplinary cases (Trial) > based on revision, in December 2003 the promulgation and implementation, to strengthen the construction of the party play very important role. Along with the development of the situation, which many provisions have been unable to fully meet the comprehensive strictly administering the practice needs. One is Ji law, more than half of the provisions and criminal law and other countries laws and regulations Repetition; two is the political discipline regulations is not prominent, not specific, for violation of the party constitution, damage theauthority of Party Constitution of misconduct lack necessary and serious responsibility to pursue; third is the main discipline for the leading cadres, does not cover all Party members. Based on the above situation, need to < the criterion of a clean and honest administration > and < rule > the two is likely to be more relevant regulations first amendment. By revising, really put the authority of Party discipline, the seriousness in the party tree and call up the majority of Party members and cadres of the party constitution of party compasses party consciousness. (II) two party regulations revision process the Central Committee of the Communist Party of China attaches great importance to two regulations revision . Xi Jinping, general books recorded in the Fifth Plenary Session of the eighth session of the Central Commission for Discipline Inspection, on the revised regulations < > made clear instructions. According to the central deployment, the Central Commission for Discipline Inspection from 2014 under six months begin study two regulations revision. The Standing Committee of the Central Commission for Discipline Inspection 4 review revised. Comrade Wang Qishan 14 times held a special meeting to study two regulations revision, amendment clarifies the direction, major issues of principle, path and target,respectively held a forum will listen to part of the province (area) secretary of the Party committee, Secretary of the Discipline Inspection Commission, part of the central ministries and state organs DepartmentThe first party committee is mainly responsible for people, views of experts and scholars and grassroots party organizations and Party members. Approved by the Central Committee of the Communist Party of China, on 7 September 2015, the general office of the Central Committee of the Party issued a notice to solicit the provinces (autonomous regions, municipalities) Party, the central ministries and commissions, state ministries and commissions of the Party (party), the General Political Department of the military, every 3 people organization of Party of two regulations revision opinion. Central Commission for Discipline Inspection of extensive solicitation of opinions, careful study, attracting, formed a revised sent reviewers. In October 8 and October 12, Central Committee Political Bureau Standing Committee and the Political Bureau of the Central Committee After consideration of the two regulations revised draft. On October 18, the Central Committee of the Communist Party of China formally issued two regulations. Can say, two laws amendment concentrated thewisdom of the whole party, embodies the party. Second, < code > and < Regulations > revision of the basic principles of two party regulations revision work and implement the party's eighteen, ten eight plenary, the spirit of the Fourth Plenary Session of the Eleventh Central Committee and General Secretary Xi Jinping important instructions on the revised < low political criterion > and < Regulations >, highlighting the ruling party characteristics, serious discipline, the discipline quite in front of the law, based on the current, a long-term, advance as a whole, with Bu Xiuding independent < rule > and < rule >. Main principle is: first, adhere to the party constitution to follow. The constitution about discipline and self-discipline required specific, awaken the party constitution of party compasses party consciousness, maintaining the authority of the constitution. General Secretary Xi Jinping pointed out that "no rules, no side round. Party constitution is the fundamental law, the party must follow the general rules. In early 2015 held the eighth session of the Central Commission for Discipline Inspection Fifth Plenary Session of the 16th Central Committee, Xi Jinping again pointed out that constitution is the party must follow the general rules, but also the general rules." the revision of the< code > and < rule > is Method in adhere to the regulations established for the purpose of combining rule of virtue is to adhere to the party constitution as a fundamental to follow, the constitution authority set up, wake up the party constitution and party rules the sense of discipline, the party constitution about discipline and self-discipline specific requirements. 4 second is to adhere to in accordance with the regulations governing the party and the party. The Party of rule of virtue "de", mainly refers to the party's ideals and beliefs, excellent traditional style. The revised the < code > closely linked to the "self-discipline", insisting on the positive initiative, for all members, highlight the "vital few", emphasized self-discipline, focusing on the morality, and the majority of Party members and the ideological and moral standards. The revised < > Ji method separately, Ji, Ji Yan to Method, as a "negative list", emphasizing the heteronomy, focusing on vertical gauge. Is this one high and one low, a positive reaction, the strict party discipline and practice results transformation for the integration of the whole party to observe moral and discipline requirements, for the majority of Party members and cadres provides benchmarking and ruler. Third, insist on to. In view of the problems existing in theparty at the present stage, the main problems of Party members and cadres in the aspect of self-discipline and abide by the discipline to make clearly defined, especially the party's eighteen years strict political discipline and political rules, organization and discipline and to implement the central eight provisions of the spirit against the four winds and other requirements into Disciplinary provisions. Not one pace reachs the designated position, focusing on in line with reality, pragmatic and effective. After the revision of major changes, major changes in the < code > and < rule > modified and needs to grasp several key problems (a) < code > < code > adhere to according to regulations governing the party and party with morals in combination, for at the present stage, the leadership of the party members and cadres and Party members in existing main problems of self-discipline, put forward principles, requirements and specifications, showing Communists noble moral pursuit, reflected at all times and in all over the world ethics from high from low 5 common requirements. One is closely linked to the "self-discipline", removal and no direct relation to the provisions of . the second is adhere to a positive advocate, "eight prohibition" 52 are not allowed to "about the content of the" negative list moved into synchronizationamendment < cases >. Three is for all the party members, will apply object from the leadership of the party members and cadres to expand to all Party members, fully embodies the comprehensive strictly required. The fourth is prominent key minority, seize the leadership of the party members and cadres is the key, and put forward higher requirements than the ordinary Party members. Five is to simplify, and strive to achieve concise, easy to understand, easy to remember. The revised < code > is the ruling Party since the first insists on a positive advocate forAll Party members and the self-discipline norms, moral declaration issued to all members of the party and the National People's solemn commitment. > < criterion of a clean and honest administration consists of 4 parts, 18, more than 3600 words. After the revision of the < code >, a total of eight, 281 words, including lead, specification and Party member cadre clean fingered self-discipline norms, etc. Part 3 members low-cost clean and self-discipline, the main contents can be summarized as "four must" "eight code". Lead part, reiterated on ideal and faith, fundamental purpose, the fine traditions and work style, noble sentiments, such as "four must" the principle of requirements, strong tone of self-discipline, The higher request for 6 andsupervised tenet, the foothold in permanent Bao the party's advanced nature and purity, to reflect the revised standards requirements. Members of self-discipline norms around the party members how to correctly treat and deal with the "public and private", "cheap and rot" thrifty and extravagance "bitter music", put forward the "four norms". Party leader cadre clean fingered self-discipline norms for the leadership of the party members and cadres of the "vital few", around the "clean politics", from civil servant of the color, the exercise of power, moral integrity, a good family tradition and other aspects of the leadership of the party members and cadres of the "four norms" < > < norm norm. "The Party member's self-discipline norms" and "party members and leading cadre clean fingered self-discipline norms," a total of eight, collectively referred to as the "eight". "Four must" and "eight" of the content from the party constitution and Party's several generation of leaders, especially Xi Jinping, general secretary of the important discussion, refer to the "three discipline and eight points for attention" statements, and reference some embody the Chinese nation excellent traditional culture essence of epigrams. (2) the revised regulations, the main changes in the revised Regulations > to fully adapt to thestrictly requirements, reflects the according to the regulations governing the law of recognition of deepening, the realization of the discipline construction and Jin Ju. < rule > is party a ruler, members of the basic line and follow. And the majority of Party members and cadres of Party organizations at all levels should adhere to the bottom line of thinking, fear discipline, hold the bottom line, as a preventive measure, to keep the party's advanced nature and purity. 1, respect for the constitution, refinement and discipline. Revised < rule > from comprehensive comb physical constitution began, the party constitution and other regulations of the Party of Party organizations and Party discipline requirements refinement, clearly defined in violation of the party constitution will be in accordance with regulations to give the corresponding disciplinary action. The original 10 categories of misconduct, integration specification for political discipline, discipline, honesty and discipline masses Ji Law and discipline and discipline and other six categories, the content of < rule > real return to Party discipline, for the majority of Party members and listed a "negative list. 7 2, highlighting the political discipline and political rules. > < Regulations according to the stage of the discipline of outstandingperformance, emphasizing political discipline and political rules, organization and discipline, in opposition to the party's leadership and the party's basic theory, basic line, basic program and basic experience, the basic requirement of behavior made prescribed punishment, increase the cliques, against the organization such as violation of the provisions, to ensure that the central government decrees and the Party of centralized and unified. 3, adhere to strict discipline in the law and discipline In front, Ji separated. Revised < Regulations > adhere to the problem oriented, do Ji separated. Any national law existing content, will not repeat the provisions, the total removal of 79 and criminal law, repeat the content of the public security management punishment law, and other laws and regulations. In the general reiterated that party organizations and Party members must conscientiously accept the party's discipline, die van comply with national laws and regulations; at the same time, to investigate violations of Party members and even criminal behavior of Party discipline and responsibility, > < Regulations distinguish five different conditions, with special provisions were made provisions, so as to realize the connection of Party discipline and state law. 4, reflect Wind building and anti-corruptionstruggle of the latest achievements. < rule > the party's eighteen years implement the spirit of the central provisions of the eight, against the requirements of the "four winds" and transformation for disciplinary provisions, reflecting the style construction is always on the road, not a gust of wind. In the fight against corruption out of new problems, increase the trading rights, the use of authority relatives profit and other disciplinary terms. Prominent discipline of the masses, the new against the interests of the masses and ignore the demands of the masses and other disciplinary terms and make provisions of the disposition and the destruction of the party's close ties with the masses.Discipline to protect the party's purpose. 8 of these regulations, a total of three series, Chapter 15, 178, more than 24000 words, after the revision of the regulations a total of 3 series, Chapter 11, 133, 17000 words, divided into "general" and "special provisions" and "Supplementary Provisions" Part 3. Among them, add, delete, modify the provisions of the proportion of up to nearly 90%. 1, the general general is divided into five chapters. The first chapter to the regulations of the guiding ideology, principles and scope of application of the provisions, highlight the strengthening ofthe party constitution consciousness, maintenance the authority of Party Constitution, increase the party organizations and Party members must abide by the party constitution, Yan Centralized centralized, would examine at all levels of the amended provisions implementing and maintaining Party discipline, and consciously accept the party discipline, exemplary compliance with national laws and regulations. The second chapter of discipline concept, disciplinary action types and effects of the regulations, will be a serious warning from the original a year for a year and a half; increase the Party Congress representative, by leaving the party above (including leave probation) punishment, the party organization should be terminated its representative qualification provisions. The third chapter of the disciplinary rules of use prescribed in the discipline rectifying process, non convergence, not close hand classified as severely or heavier punishment. "Discipline straighten "At least eighteen years of five years, these five years is to pay close attention to the provisions of the central eight implementation and anti -" four winds ". The fourth chapter on suspicion of illegal party disciplinary distinguish five different conditions, with special provisions were madeprovisions, to achieve effective convergence of Party and country 9 method. < rule > the provisions of Article 27, Party organizations in the disciplinary review found that party members have committed embezzlement, bribery, dereliction of duty dereliction of duty and other criminal law act is suspected of committing a crime shall give cancel party posts, probation or expelled from the party. The second is < Regulations > Article 28 the provisions of Party organizations in the disciplinary review But found that party members are stipulated in the criminal law, although not involved in a crime shall be investigated for Party discipline and responsibility should be depending on the specific circumstances shall be given a warning until expelled punishment. This situation and a difference is that the former regulation behavior has been suspected of a crime, the feeling is quite strict, and the latter for the behavior not involving crime, only the objective performance of the provisions of the criminal code of behavior, but the plot is a crime to slightly. < Regulations > the 29 provisions, Party organizations in the discipline review found that party members and other illegal behavior, affect the party's image, the damage to the party, the state and the people's interests, we should depend on the situationSeriousness given disciplinary action. The loss of Party members, seriously damaging the party's image of behavior, should be given expelled from the party. At this article is party member is in violation of the criminal law outside the other illegal acts, such as violates the public security administration punishment law, customs law, financial laws and regulations behavior. The fourth is < cases > Article 32 stipulates, minor party members and the circumstances of the crime, the people's Procuratorate shall make a decision not to initiate a prosecution, or the people's court shall make a conviction and exempted from criminal punishment shall be given within the party is removed from his post, probation or expelled from the party. Party members and crime, sheets were fined in accordance with For acts; the principal Ordinance amended the provisions of the preceding paragraph. This is the new content, in order to achieve Ji method effective convergence. Five is < > the thirty third article 10 of the provisions, the Party member due to an intentional crime is sentenced to criminal law (including probation) sheets or additional deprivation of political rights; due to negligence crime and was sentenced to three years or more (excluding three years) a penalty, shall give expelled punishment. Due to negligence crime is convictedand sentenced to three years (including three years) in prison or be sentenced to public surveillance, detention, shall in general be expelled from the party. For the individual may not be expelled from the party, should control Approval. This is followed and retained the original > < Regulations the provisions of punishment party authorization rules and report to a level party organizations. For is "party members with criminal acts, and by the criminal punishment, generally should be expelled from the party". The fifth chapter of probationary Party member of the discipline and discipline after missing members of the treatment and punishment decisions, such as the implementation of the provisions, clear the related party discipline and punishment decision made after, for duties, wages and other relevant alteration formalities for the longest time. 2, sub sub section will the original regulations of10 categories of acts of violation of discipline integration revised into 6 categories, respectively, in violation of the punishments for acts of political discipline "in violation of discipline behavior of punishment" in violation of integrity of disciplinary action points "of violation punishments for acts of mass discipline" "the violation of work discipline, punishment" in violation of discipline of life behaviorpunishment "6 chapters. 3, annex" Supplementary Provisions "clear authority making supplementary provisions of, cases of interpretative organ, as well as regulations implementation time and retroactivity etc.. 11 (3) learning understanding > < regulations needs to grasp several key problems The first problem -- about the violation of political discipline behavior > < new ordinance chapter 6 the political discipline column for the six disciplines, that is the main opposition to Party leadership and the opposition of the basic theory, basic line, basic program and basic experience, basic requirements of misconduct made provisions of the disposition, especially the eighteen since the CPC Central Committee put forward the Yan Mingzheng treatment of discipline and political rules requirements and practical achievements transformation for Discipline article, increase the false debate central policies, cliques, against the organization review, make no discipline of the principle of harmony terms. These are the party's eighteen years in comprehensive strictly Process combined with the practice of rich content. (1) false debate the central policies and undermine the Party of centralized and unified the problem is made in accordance with the provisions of the party constitution. Constitution in general programme requirementsadhere to democratic centralism is one of the requirements of the construction of the party must adhere to the four cardinal. Application of this principle is not only the party the basic organization principle and is also the mass line in party life, it requires that we must fully develop inner-party democracy, respect for the dominant position of Party members, safeguarding the Party member democratic rights, give full play to the enthusiasm and creativity of the party organizations at all levels and Party members, at the same time, also must implement the right concentration, ensure the party's mission < the chaos in unity and concerted action to ensure that the party's decision to get quickly and effectively implementing. The Party Central Committee formulated the major principles and policies, through different channels and ways, fully listen to the party organizations and Party members of the opinions and suggestions, but 12 is some people face to face not to say back blather "" will not say, after the meeting said, "" Taiwan does not say, and nonsense ", in fact, not only disrupt the people thought, some causing serious consequences, the damage to the Party of the centralized and unified, hinder the central policy implementation, but also a serious violation of the democratic system of principles. There is no doubt that shall, inaccordance with the Regulations > 4 Specified in Article 6 to give the appropriate punishment. For did not cause serious consequences, to give criticism and education or the corresponding tissue processing. (2) about the destruction of the party's unity < New Regulations > the forty eighth to fifty second article, to damage Party's unity unified and violation of political discipline, punishment situation made explicit provisions. Article 52 of the new "in the party get round group, gangs seek private gain, cliques, cultivate private forces or through the exchange of interests, for their own to create momentum and other activities to gain political capital, given a serious warning or withdraw from their party posts disposition; if the circumstances are serious, to give Leave a party to observation or expelled from the party. (3) on against the organization review of the provisions of the constitution, party loyalty honesty is party members must comply with the obligations. Members must obey the organization decision, shall not violate the organization decided encounters by asking questions to find organization, rely on the organization, shall not deceive the organization, against the organization. For example, after the investigation does not take the initiative to explain the situation, but to engage inoffensive and defensive alliance, hiding the stolen money is against survey organization, is a violation of the behavior of political discipline. Article 24 of the original > < Regulations, although the provisions of the interference, hinder group review the behavior of the fabric can be severely or 13 Aggravated punishment, but did not put this kind of behavior alone as a discipline for qualitative amount of discipline. > < new regulations increase the Article 57, "anti organization review, one of the following acts, given a warning or serious warning; if the circumstances are relatively serious, giving removed from or placed on probation within the party post; if the circumstances are serious, give expelled from the party: (a) on supply or forged, destroyed, transfer, conceal evidence; (II) to prevent others expose, providing evidence Material; (III) harboring co personnel; (4) to the organization to provide false information, to hide the fact;(5) the him against the acts of the organization review. "< rule > add this clause to the Constitution requires more specific, the previous no punishment in accordance with the definite list and put forward clear punishment in accordance with. (4) about organizing or participating in superstitious activities as < Regulations > about engage in activities of。

配电柜出厂试验报告

配电柜出厂试验报告
1. 测试目的
本次出厂试验的目的是验证配电柜的性能和安全可靠性，确保其符合相关标准和规范要求。

2. 试验对象
配电柜型号: [填写配电柜型号]
制造商: [填写制造商]
3. 试验内容和方法
3.1 功能性试验
3.1.1 输入电压合格试验
- 在额定电源电压下，检查配电柜是否能正常接受电源输入。

- 确保输入电压范围和电流符合设计要求。

3.1.2 输出电压和电流测试
- 测试配电柜输出的电压和电流是否符合设计要求。

- 记录并比对测量结果。

3.1.3 短路保护试验
- 通过短接配电柜的输出，确认是否触发短路保护装置。

- 确认短路保护装置的响应时间和保护能力。

3.2 安全性试验
3.2.1 绝缘电阻试验
- 测试配电柜各电路之间的绝缘电阻是否满足要求。

- 使用绝缘电阻测试仪进行测量。

3.2.2 接地电阻试验
- 测试配电柜的接地电阻是否满足安全要求。

- 使用接地电阻测试仪进行测量。

3.2.3 温升试验
- 在额定负载下，检查配电柜各元器件的温度变化。

- 检查温度是否超出安全范围。

4. 试验结果
根据以上试验内容和方法，配电柜通过了所有功能性和安全性试验。

各项指标均符合相关标准和规范要求。

5. 试验结论
经过本次出厂试验，确认配电柜的性能和安全可靠性达到要求。

符合相关标准和规范要求。

6. 签署
试验机构：[填写试验机构名称]
试验日期：[填写试验日期]。

配电箱出厂检验报告(2024)

配电箱出厂检验报告（二）引言概述：本次配电箱出厂检验报告旨在对配电箱进行全面的检验和评估，确保其符合相关国家标准和行业要求。

通过本次检验，能够确保配电箱的质量和可靠性，保障其在安全和可靠性方面的性能。

正文内容：1.外观检验1.1配电箱外壳1.1.1通过目视检查，外壳无明显变形、裂纹、划痕等缺陷。

1.1.2外壳表面光滑且无锈蚀或脱漆现象。

1.1.3配电箱的外部标识清晰可读，标注符合相应国家标准和规范要求。

1.2配电箱门1.2.1配电箱门开闭灵活，并配备可靠的门锁装置。

1.2.2配电箱门密封良好，确保内部元器件不受外界灰尘、湿气等影响。

2.内部结构检验2.1配电箱内部导线连接2.1.1检查配电箱内导线连接是否牢固，无松动和断裂现象。

2.1.2导线接头处均采用绝缘套管进行包覆，确保绝缘性能。

2.1.3配电箱内导线标准、规格和颜色符合相应的电气标准。

2.2配电箱电器设备2.2.1检查配电箱内的电器设备如断路器、熔断器等是否符合相关标准，且工作可靠。

2.2.2确保电器设备的额定电流与配电箱的负荷要求相匹配。

2.2.3测试电器设备动作可靠性和保护性能，确保在过载和短路情况下能及时断电保护。

3.绝缘性能检验3.1使用绝缘电阻表对配电箱的导线和绝缘件进行测量，确保其绝缘电阻值符合相关标准要求。

3.2检查配电箱的绝缘材料和绝缘涂层，确保其完好无损，绝缘性能良好。

4.过载和短路保护测试4.1使用专业测试设备对配电箱的过载保护和短路保护功能进行测试。

4.2确保过载保护功能的动作时间符合国家标准要求，能有效保护电器设备。

4.3确保短路保护功能的动作时间符合国家标准要求，能及时切断异常电流，避免事故发生。

5.漏电保护测试5.1使用专业测试仪器对配电箱的漏电保护器进行测试。

5.2确保漏电保护器的动作电流和动作时间符合相关标准要求。

5.3测试漏电保护器能否可靠地切断漏电电流，保护人身安全。

总结：本次配电箱出厂检验过程中，对配电箱外观、内部结构、绝缘性能、过载和短路保护以及漏电保护进行了全面检查和测试。

电气控制柜出厂检验报告单

电气控制柜出厂检验报告单报告单编号：2024-001企业名称：XXX有限公司产品名称：电气控制柜出厂日期：2024年1月1日一、产品概述二、检验内容本次检验旨在验证电气控制柜的安全性、可靠性、功能性等方面是否符合相关标准要求，并检验产品的性能指标是否满足技术要求。

三、检验方法1.外观检验：对电气控制柜的外观进行检验，包括外壳是否完整且无明显损伤、开关按钮是否灵活、标识是否清晰等。

2.绝缘电阻测量：使用万用表对电气控制柜的绝缘电阻进行测量，确保其绝缘性能符合要求。

3.功能性测试：对电气控制柜的各个部件进行功能性测试，例如主开关、照明开关、电流表、电压表等。

4.短路保护测试：通过模拟短路故障，检验电气控制柜的短路保护功能是否正常。

5.接地保护测试：使用接地测试仪对电气控制柜的接地保护效果进行测试，确保其符合相关标准要求。

四、检验结果1.外观检验：电气控制柜的外观完整无损，开关按钮灵活，标识清晰可读。

2.绝缘电阻测量：测量结果显示，电气控制柜的绝缘电阻均达到标准要求，符合安全性要求。

3.功能性测试：各部件功能正常，主开关、照明开关、电流表、电压表等均能正常工作。

4.短路保护测试：在模拟短路故障下，电气控制柜能及时切断电路，有效保护设备。

5.接地保护测试：接地测试仪显示，电气控制柜的接地保护效果良好，符合相关标准要求。

五、结论经过本次出厂检验，电气控制柜的安全性、可靠性、功能性等方面均符合相关标准要求，性能指标满足技术要求。

符合出厂要求，可以进行发货销售。

六、建议1.在生产过程中，加强对电气控制柜外壳的保护，确保运输和使用过程中不会导致外观损坏。

2.继续保持对电气控制柜各部件的质量把控，确保产品功能正常可靠。

3.根据市场反馈，不断改进产品设计和性能，提高产品竞争力。

七、其他报告编制人：XXX。

电气控制柜（箱）出厂检验报告单.docx

电气控制柜（箱）出厂检验报告单.docx
电气控制柜(箱)出厂检验报告单
NO.
产品名称：型号规格：
产品编号：检验依据：GB7251.1-5
序
号
检测项目与技术要求检验方法检测结果
1 一
般
检
查
面板平整、焊接均匀牢靠、无明显变形、涂层完好
目测元件安装牢固
二次配线连接牢固、端头有标志、相序排列正确
接地等标志符合要求。

2 尺
寸
检
查
门开启角度>90度,灵活开启
目测
卷尺电气间隙：≥10mm
爬电距离：≥15mm
3 介
电
试
验
导电部件与地之间、导电部件之间
2500V 1S 无闪络或击穿
控制回路与地之间
2000V 1S 无闪络或击穿
绝缘手柄对地
3750V 1S 无闪络或击穿
CC2672型
耐压测试仪
4 保护
电路
连续
性试
验
抽测接地电阻（电阻应≤100 mΩ）a）开关支架与地
CC2520型
接地电阻测试仪b）仪表门锁与地5 通
电
试
验
按原理图、效用通电试验通电试验台本产品出厂检验结论：检验日期：检验员：
知识改变命运
1 / 1。

配电柜出厂检验报告

电控柜验收报告
项目名称：编号：柜体名称柜体规格
柜体类型柜体数量
项目检验项目及技术要求检验结果备注绝缘
测试
1、相间电阻、及相线与中线电阻应大于500MΩ。

合格/不合格
耐压测试1、主电路带电部件与地（框架）之间，2500V在5
秒无击穿、无闪络现象。

合格/不合格2、主电路母排各相之间，2500V5秒无击穿、无闪
络。

主回路导线之间，750V5秒无击穿、无闪络，
二次回路500V5秒无击穿、无闪络。

合格/不合格
保护电路的连续性1、主接地线与门（箱体）之间的的连续性试验，接
地电阻<0.1Ω，试验电流为》10A
合格/不合格
2、主接地线与柜体裸露导电部件之间，接地电阻<0.1
Ω，试验电流为》10A。

合格/不合格
通电测试1、按装置的电气原理图要求进行模拟动作试验，试
验结果应符合要求，5次以上均正常动作。

合格/不合格2、安装置的电气原理图要求进行故障模拟试验，其
故障信号和报警指示应正确。

合格/不合格
3、通电试验时每个回路的一、二次接线均正确无误。

合格/不合格
4、各回路开关的容量应与图纸相符。

合格/不合格
显示指示1、各种标签标识必须与图纸、工艺测试指示相吻合。

合格/不合格
2、同一设备不同标示、指示应协调一致。

合格/不合格
性能参数1、变频器、软启动器、热继电器、时间继电、仪表
等参数必须按所需功能设定。

合格/不合格。

配电柜出厂检验报告

Forpersonaluseonlyinstudyandresearch;not f or commer ci al use螂电控柜验收报告袆项目名称：编号：羄腿蚇柜体名称蕿柜体规格螄芇肆柜体种类薁柜体数目蒆项目膁查验项目及技术要求查验结果备注绝缘1、相间电阻、及相线与中线电阻应大于500MΩ。

合格/不合格测试1、主电路带电零件与地（框架）之间，2500V在5合格/不合格耐压秒无击穿、无闪络现象。

测试2、主电路母排各相之间，2500V5秒无击穿、无闪合格/不合格络。

主回路导线之间，750V5秒无击穿、无闪络，二次回路500V5秒无击穿、无闪络。

保护电路的连续性通电1、主接地线与门（箱体）之间的的连续性试验，接合格/不合格地电阻Ω，试验电流为》10A2、主接地线与柜体裸露导电零件之间，接地电阻合格/不合格Ω，试验电流为》10A。

1、按装置的电气原理图要求进行模拟动作试验，试合格/不合格验结果应切合要求，5次以上均正常动作。

测试显示指示性能参数品牌查验包装2、安装置的电气原理图要求进行故障模拟试验，其故障信号和报警指示应正确。

3、通电试验时每个回路的一、二次接线均正确无误。

4、各回路开关的容量应与图纸符合。

1、各样标签表记一定与图纸、工艺测试指示相符合。

2、同一设施不一样标示、指示应协调一致。

1、变频器、软启动器、热继电器、时间继电、仪表等参数一定按所需功能设定。

1、元件器品牌型号应与图纸或许报价单调致。

1、编号管、图纸、安装附件应齐备。

2、柜面、显示部分或突出部分应有保护举措。

3、包装应有方向说明及注意事项。

合格/不合格合格/不合格合格/不合格合格/不合格合格/不合格合格/不合格合格/不合格合格/不合格合格/不合格合格/不合格质检综合结论：查验部门：质检人：查验日期：。

电控柜检验记录范文

电控柜检验记录范文日期：XXXX年XX月XX日检验单位：XXX公司检验人员：XXX一、检验目的与背景电控柜是工业生产过程中必不可少的设备，通过对电控柜进行检验，可以确保其安全可靠地运行，避免发生火灾、漏电等意外事故。

本次检验旨在对电控柜的电气性能进行全面检测，确保其符合相关的技术标准和规定。

二、检验内容1.功能性检验：检查电控柜各设备的功能是否正常，如接触器、继电器、断路器等；2.接地电阻检验：检查电控柜的接地电阻，确保能有效地排除漏电等危险；3.绝缘电阻检验：检查电控柜的绝缘电阻，确保符合安全要求；4.动作试验：对电控柜的保护开关、断路器、电压互感器等进行动作试验，确保正常工作；5.火灾灭火器材检验：检查电控柜内是否安装有灭火器材，灭火器材是否符合相关要求；6.可视检查：对电控柜的外观、标志、线缆等进行检查，确保无明显的损坏或磨损。

三、检验结果1.功能性检验结果：经检验，电控柜中的各设备功能正常，无异常情况。

2.接地电阻检验结果：电控柜的接地电阻为XΩ，符合相关标准。

3.绝缘电阻检验结果：电控柜的绝缘电阻为XΩ，符合相关要求。

4.动作试验结果：电控柜的保护开关、断路器、电压互感器等在动作试验中正常工作，检验合格。

5.火灾灭火器材检验结果：电控柜内安装了符合要求的灭火器材，可满足灭火需要。

6.可视检查结果：电控柜外观无明显的损坏或磨损，标志清晰可读，线缆无松动或断裂情况。

四、存在的问题及处理措施1.检验过程中发现，电控柜一侧的排风扇存在异响。

处理措施：拆卸排风扇进行清洗和维修，并更换损坏零件。

2.检验过程中发现，电控柜内电缆部分存在松动情况。

处理措施：重新安装和固定松动的电缆，确保固定牢靠。

五、结论与建议经过全面的检验，电控柜的电气性能符合相关的技术标准和规定，可以正常使用。

但在实际使用过程中，还需注意定期清洁和维护电控柜，确保其处于良好的工作状态。

同时，加强人员培训，提高操作人员的安全意识和应急能力，以防止事故的发生。

控制柜出厂检验报告

控制柜出厂检验报告1. 引言控制柜是工业自动化领域中必不可少的设备之一，用于控制和管理机械设备的运行。

为保证控制柜的质量和性能符合标准要求，我们进行了控制柜出厂检验。

本报告详细介绍了检验的过程、方法以及结果。

2. 检验对象本次出厂检验的控制柜型号为XXX，规格为XXX，生产厂家为XXX。

控制柜的主要功能是控制电动机的启动、停止和频率调节，保证机械设备的正常运行。

3. 检验标准本次出厂检验参照了国家标准XXX和相关行业标准，对控制柜的外观、电气性能、安全性能和环境适应能力等方面进行了评估。

4. 检验过程4.1 外观检验外观检验主要对控制柜的外部结构、涂装质量以及组装工艺进行评估。

经过检查，控制柜外观无明显变形、划痕或破损现象，涂装质量符合标准要求。

4.2 电气性能检验电气性能检验主要针对控制柜内部的电气元件、接线端子以及布线等进行评估。

我们使用专业的电气测试仪器对控制柜的电流、电压、频率等参数进行测试。

经过检验，控制柜内部的电气元件连接良好，电流、电压等参数在标准范围内。

4.3 安全性能检验安全性能检验主要对控制柜的保护装置和接地系统进行评估。

通过对控制柜中继电器的工作状态进行检查，保证控制柜能够对电机的过载、欠电压、过热等故障进行保护。

此外，我们还对控制柜的接地系统进行了检查，确保防止触电防护措施的有效性。

4.4 环境适应能力检验环境适应能力检验主要评估控制柜在不同环境条件下的运行状况。

我们将控制柜置于高温、低温、高湿和低湿等环境条件下，并对控制柜的工作稳定性进行观察。

经过测试，控制柜在各种环境条件下均能正常工作。

5. 检验结果根据以上的检验过程和标准要求，我们得出如下的检验结果：外观检验：合格电气性能检验：合格安全性能检验：合格环境适应能力检验：合格6. 结论经过本次出厂检验，我们认为该控制柜的质量和性能符合标准要求，可放心投入使用。

同时，我们建议在使用过程中，定期进行维护、保养和检测，以确保其长期稳定运行。

电控柜出厂检验报告

电控柜出厂检验报告一、检验目的电控柜是工业生产过程中的重要设备之一，其质量和性能直接关系到生产线的稳定运行和安全生产。

本次出厂检验的目的是确保电控柜在设计和制造过程中的合格性，以及保证其在实际使用过程中的性能和安全性。

二、检验内容1.外观检验：检查电控柜表面涂装是否均匀、无划痕及锈蚀，标志标牌是否齐全、清晰可辨，连接线路是否整齐，无错位等情况。

2.电气性能检验：检查电控柜内的电气元件和设备连接是否正确，电缆接头是否牢固可靠，线路连接是否无短路、断路等故障，电流、电压和频率是否符合设计要求。

3.环境适应性检验：检查电控柜在不同的温度、湿度和振动环境下的性能表现，确保其能够在各种环境条件下正常运行。

4.安全性检验：检查电控柜的防护等级、绝缘性能和接地状态是否符合国家标准和设计要求，是否存在触电、漏电等安全隐患。

5.功能性检验：检查电控柜中的各项功能是否正常，如断路器的分合闸动作是否灵敏可靠，仪表、指示灯和报警器的使用是否准确可靠等。

三、检验方法1.目测检查：通过对电控柜外观的观察和检查，发现外观缺陷和连接线路错误等问题。

2.电气参数测量：借助于电流表、电压表和多功能仪等工具，测量电控柜内部电流、电压和频率等参数，判断其是否符合设计要求。

3.试验仪器检测：使用万用表、绝缘电阻测试仪和接地电阻测试仪等工具，对电控柜的绝缘性能和接地状态进行检测。

4.功能性测试：通过模拟实际使用情况，对电控柜中的各项功能进行测试，查看是否正常工作。

四、检验结果经过检验，本次出厂的电控柜共检测出以下问题：1.外观方面：部分表面涂装存在不均匀、划痕和锈蚀现象，需要重新处理。

2.电气性能方面：电缆接头存在松动现象，需要加强固定；部分线路连接存在短路和断路，需要重新连接。

3.安全性方面：部分绝缘材料存在老化和损坏现象，需要更换；接地电阻超出标准范围，需要重新接地。

4.功能性方面：部分断路器分合闸动作不灵敏，需要调试竣工。

五、处理措施1.外观问题：重新进行喷涂和抛光处理，确保表面涂装均匀无划痕。

低压电气柜出厂检验报告

1.1
铭牌
Name pate
内容正确、清晰；安装端正、牢固。
The contents are correct and clear,Assemble is neatly and stable.
1.2
框架结构
Frame structure
框架外形及安装尺寸应符合图纸及工艺要求。
Th.overal.dimension.an.installatio.dimension.shoul.mee.th.requirement.o.drawing.an.technology...
涂色均匀,不反光；漆膜无露底、起皱、流痕、斑点及杂物,有良好的附着力；电镀层无起皮、脱落、发霉及锈蚀现象。
The painting is homogeneous,is free from light reflection,scratches flowing path,flaws and disposals,and it has good abhesive strength.The galvanizing is free from delaminating,mildew and rust.
电气间隙Electrical gap: 23 mm
爬电距离Leakage distance:25 mm
1.5
辅助回路配线Wiring
of
auxiliary circuit
线路整齐美观、牢固,标号清晰、正确。导线颜色、截面、布置方式符合标准及工艺要求；辅助回路电气间隙符合标准规定要求。
The wiring is nest and stable.The symbols are clear and correct.The colour ,cross section and arrangement of wires meet the requirements of standards and technology.

配电柜出厂检验报告

质检综合结论：
检验部门：
质检人：
检验日期：
性能
参数
1、变频器、软启动器、热继电器、时间继电、仪表等参数必须按所需功能设定。
合格/不合格
品牌检验
1、元件器品牌型号应与图纸或者报价单一致。
合格/不合格
包
装
1、编号管、图纸、安装附件应齐全。
合格/不合格
2、柜面、显示部分或突出部分应有保护措施。
合格/不合格
3、包装应有方向说明及注意事项。
合格/不合格
合格/不合格
保护电
路的连
续性
1、主接地线与门（箱体）之间的的连续性试验，接地电阻<Q，试验电流为》10A
合格/不合格
2、主接地线与柜体裸露导电部件之间，接地电阻<
Q，试验电流为》10A。
合格/不合格
通电
测试
1、按装置的电气原理图要求进行模拟动作试验，试验结果应符合要求，5次以上均正常动作。
合格/不合格
2、安装置的电气原理图要求进行故障模拟试验，其故障信号和报警指示应正确。
合格/不合格
3、通电试验时每个回路的一、二次接线均正确无误。
合格/不合格
4、各回路开关的容量应与图纸相符。
合格/不合格
ห้องสมุดไป่ตู้显示
指示
1、各种标签标识必须与图纸、工艺测试指示相吻合。
合格/不合格
2、同一设备不冋标示、指示应协调一致。
合格/不合格
电控柜验收报告
柜体名称
柜体规格
柜体类型
柜体数量
项目
检验项目及技术要求
检验结果
备注
绝缘
测试
1、相间电阻、及相线与中线电阻应大于500MQ。