压铸机和模具常用语
模具专业术语英语
模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。
压铸专业词汇
A安装尺寸 install dimension凹模固定板 retainer plate凹模 female die, female mold, negative moldB备件 spare parts变质 modification变质剂 modification agent扒渣 slagging-off保温炉 holding furnace保压压力 dwell pressure表面缺陷 surface defectC 淬火硬度quenching hardness抽芯core侧面抽芯side core抽芯油缸core oil cylinder插拔式结构plug抽芯机构core puller抽芯油缸支架bracket of cylinder粗糙度roughness/degree铸件表面粗糙度surface roughness擦伤galling尺寸公差dimension tolerance of casting除气degassing吹气净化blow purifying除气剂degassing flux出渣de-slagging出渣口slag hole沉渣sludge出炉口tap hole菜花头Cauli-flowering超声波检验ultrasonic test重熔re-meltingD 端盖cover动模垫块spacer parallel锻钢 forged steel氮化处理nitriding treatment断裂fracture塑性断裂plastic fracture导柱guide pillar导套guide sleeve导向板guide plate导向件guide part动型moving die/ejector die/movable mould动模座板moving clamp plate/bottom clamping plate 定模座板fixed clamp plate/top plate定型fixed die/cover die定模套版bolster/fixed die顶杆ejector pin顶出结构ejector mechanism顶出ejector吊装孔lifting eye吊环lifting ring镀钛处理titanium plating treatment多肉缺陷metallic projection电火花electric spark打磨grindingF 分流锥 divider/blast cone分型面 mold parting/parting face/mold joint附页 attachment/appendix复位杆 reset bar(rod)附件故障 accessory覆盖剂 covering flux废金属料scrap浮渣cinder反射炉 reverberatory furnace废品 reject飞边joint flash仿真simulationG规格 specification/standard数值孔径 numerical aperture (N.A)固定段 segment坩埚crucible坩埚炉crucible furnace感应电炉electric induction furnace沟槽 blind scab硅SiliconH滑块 sliding block滑块部件 moving parts滑块退让 return/move back焊补 welding-on横浇道 runner合模 die locking横流道 runner回炉料foundry returns合型 mold assembling/closing/die locking合型力 die locking force化学成分不合格chemical consistence analysisJ 浇口套 sprue bush浇排道系统pouring system浇不足 misrun浇注 pouring浇注断裂interrupted pour浇道比 gating ratio浇包 ladle精整dressing and finishing精度 accuracy接口 connector击伤 shot damage金相组织 metallographic structure金属残液heel金相检验metallographic test金属型涂料 die coating/coating for metal mold加压速度 rate of pressure increasing间隙 clearance精炼refining精炼剂refining flux精密铸造 precision casting静置holding/stewing渗透 impregnation集渣装置dirt traps夹杂类缺陷inclusion defects夹渣entrapped slag/slag inclusion夹具 tool fixturesK壳体 housing开炉 blowing in孔洞缺陷cavity库存 inventoryL冷却 cooling冷却水管 cooling water pipe冷却耐压管 cooling pressure pipe冷却水管用密封圈 O-ring/sealing ring/gasket ring冷室卧式压铸机 horizontal (cold chamber) die casting machine 冷却系统 cooling system冷却水接口 cooling water connector冷裂 cold crack冷隔 cold lap铝 Aluminum裂纹 crack拉伤 caught casting拉杆孔 draw bar螺纹 screw/thread螺纹结构 screw structure螺纹公称直径(直径 diameter)公称尺寸(名义尺寸) specified size/nominal dimension漏油 leakage of oil棱边倒角 edge炉料 charge炉衬 furnace lining炉气分析flue gas analysis炉前分析on-the-spot sample analysis流痕 bloom/flow line力学性能不合格 physical-mechanical characteristic abnormalM 毛坯 rough/blank毛坯铸件 rough casting毛刺 veining/burr模芯 core模框 frame模槽 mold channel模套 chase/bolster/frame模具钢 die steel模具图纸 mold drawing内浇口 in-gate冒口 riser/feeder head冒口浇注系统 feeder head gating system镁 Magnesium锰 Manganese密闭耐压系统 tightness testN 内浇道 in-gate镍 NickleP配油盘 pressure plate排气块 exhaust block排气槽 air vent排气孔 vent/venting channel排气塞 venting plug配合套圆形:fitting sleeve 方型: fitting case跑铝 aluminum slop out of mold喷射冶金 injecting metallurgy喷丸清理 shot blasting cleaning抛丸清理 wheel blasting cleaning偏析 segregation破坏性实验 destructive testQ取件机 extractor去除浇冒口 de-gating清铲 chipping缺陷铸件 defecting casting气孔 blowhole/gas cavity/pinhole/porosity 气孔缩 blowhole shrinkage去毛刺 de-burring去除氧化皮 de-scaling氢 Hydrogen清理 cleaningR 热处理 heat treatment热电偶测温孔 thermocouple well热电偶 thermocouple (TC)/pyod热裂 hot heating熔炼 smelting熔化率 melting rate熔炼损耗 total melting loss熔池 bath熔剂 flux熔渣 slagS 水管 water pipe三维造型 3 D三坐标测量仪 coordinate 3上模座板 upper clamping plate缩孔 shrinkage缩松 dispersed shrinkage疏松 porosity(dispersed shrinkage)渗漏 leakage缩陷 sink/sink in/depression试块 test block/test piece/coupon实时控制系统 real-time control system试模 de-buggingT 推板 push plate推杆 push rod推板导柱 push plate guide pillar推板导套 push plate guide sleeve凸模固定板 punch-retainer plate铜 copper钛 TitaniumW 网状裂纹 craze crack/crazing/checking 未浇满 poured shortX 型芯 core型腔 mold cavity镶拼处 splicing place斜导柱孔 hole of inclined guide pillar 楔紧块 wedge型芯弯曲 core bending下模座板 lowering clamping plate型芯固定板 core-retainer plateX 光射线检验 X-ray inspectionY 压铸机 die casting machine压室 pressure chamber压室止口(定位)尺寸 dimension/size压实 squeezing compaction压射 shot/injection压射冲头 injection piston(ram)/plunger 压铸型 die casting die压力铸造模具 die-casting die易损镶块 wear insert易损件 wearing parts预应力 pre-stress永久型 permanent mold硬点 hard spot溢流槽 over flow well印痕 indentation氧 Oxygen荧光检验 fluorescent testZ真空接口 vacuum connector真空排气管 vacuum exhaust block总接头 main connector中接头 middle connector直浇道 sprue转接处(转口)transit装配图(铸型装配图) mold assembly drawing 铸钢 cast steel支架 ejector housing/mold base leg造渣 slag forming真空熔炼 vacuum melting真空压铸 vacuum die casting/ evacuated die casting 增压 pressurization针孔 pinhole沾铝 adhesive aluminum直读光谱分析仪 direct-reading spectrograph转运包 transfer ladle转向器steering rack柴油式传动叉车 Diesel forklift复印机 copying machine服务器 Server绘图仪 Graphic plotter兼容机 compatible machine材料库 warehouse投影仪 projector半自动车床 semi-automatic lathe半自动立式钻床 drill machine表面粗度测量仪 surface roughness gauge布洛维硬度计 Brinell hardness gauge测氢仪 Hydrogen gauge叉车充电机 charger程控交换机 exchanger齿轮油泵 oil pump储气罐 accumulator tank电动葫芦 Gantry crane电动试压泵 press tester电动斜切机 bias cutter电子秤 weighing scale电子扫描仪 scanner吊斗 spoon hopper高压离心风机 combustion blower管道泵 process water pump烘箱 oven监控系统 monitoring system简易数控车床 digital lathe交流弧焊机 Are welder抛光机 polisher锯床 saw空压机 air compressor冷冻式干燥机 dryer红外线测温仪冷却塔 cooling tower立式带锯床 band saw滤油机 oil filter焊接机 welder模温机 die heater喷粉室回收设备 painter system平面磨床 grinder气动量仪 air gauge切割机 cut-off machine清洗机 washer散热器攻丝机 tapping machine台式光谱仪 spectrograph台式砂轮机 abrasive machine卧式液压拉床 broaching machine铣床 milling machine钻床 drilling machine液压机 hydraulic machine真空机 vacuum pump时效炉 aging furnace电阻炉 stress relief furnace探伤机 diagnostic machine加工中心 machining center车床 lathe钻削中心 drilling & cutting center别克 Buick切边机 trim press冷却塔循环泵 cooling tower pump循环水离心泵 process water pump脱模剂压送机 die lube station取件机 extractorFL充痒压铸系统 FL oxygen feed die cast system 装卸车 loader在建工程 construction in progress捡漏机 picker纸芯式滤油器paper element filter电磁阀 solenoid valve溢流阀spillover valve调速阀 speed control valve压力传感器pressure transducer三角带wedge shaped belt节流阀throttle governor同步齿型带timing belt喷涂机spray coater轴承(main) bearing浮球阀 float valve/ball cock行车bridge crane平衡重式叉车counter balanced forklift轮毂螺栓wheel hub bolt制动蹄片brake shoe制动液braking fluid叶片lamina/vane侧护板side guard plate单列向心推力球轴承single row radial thrust ball bearing带防尘盖单列轴承single row bearing shielded急停按钮 scram button三相开关threephase switch行程开关 limit/travel switch断路器circuit breaker接触器 contactor中间继电器intermediate relay时间继电器 time relay控制变压器control transformer开关电源switching supply节能灯energy-saving lamp日光灯管fluorescent tube自整流高压汞灯泡self-rectifying high pressure mercury lamp 电工胶布garrers/electrical tape焊条welding rod石笔slate pencil外圆磨床external grinderHydraulic fluid oil 液压油Safety hook/bolts 安全钩Crosshead 十字头Tail stock 尾架尾座Frame cover 护板框盖Toggle top cover 肘环顶Coupling 联轴器Tie-bar 拉杆, 系杆Control panel 控制面板Power board 分配板, 配电板Overhauling 大修, 拆修Hose 软管, 水龙带Warranty period 保修期Nozzle 管口, 喷嘴Nature tan 日晒后的颜色, 茶色Electric fitting 电装、Rubber pad 橡胶垫Shock absorbing rubber stopper 减震橡皮塞Die height 模子闭合高度Die stroke 动模行程Intensification ratio standard 增强比标准Plunger stroke 柱塞行程Plunger tip penetration 冲头穿透力Viscosity index 粘度指数Rated pressure 额定压力Plug socket 插口, 塞孔Ventilated 通风的Anchor bolt hole 地锚(脚)螺栓孔Inlet 入口Galvanize 通电流Carbon grain 碳粒Mortar 火泥, 砂浆Stretcher 拉伸机Earthing cable 接地电缆Manifold 总管, 集合管Clamp force sensor 夹紧力传感器Attenuate 削弱Emulsification 乳化作用中子线 wire for sliding出模斜度 draft angle隔皮 bur掉肉 misrun研配 grindTurbidity 浑浊度Refract meter 折光仪Sediment 沉淀物Glycol 乙二醇Combustible 易燃的Water-soluble 水溶性的Grease pump 黄油泵，油脂泵Drooling 滴料Disulfide 二硫化物Lithium 锂Gauge cock 试水位旋塞Pressure match valve 压力拟合阀Lock/check nut 防松螺母Slant 倾斜Core sliding face 型芯滑面Flux treatment 熔剂处理Die clamping cylinder 模具夹紧气缸Clogging 堵塞，闭合Electrode bar 电极棒Fumigation certificate 熏蒸消毒证书Crate 条板箱，柳条箱Resin parts 树脂零件Oil ring 油环Gear box 齿轮箱，传动箱,变速箱Draft angle 出模斜度Tap and drill gauge 丝锥及钻头规Tap borer 螺纹底孔钻Tap cutter 丝锥刀具Tap die holder 丝锥板牙两用夹头Tap handle 丝锥扳手Screw funnel 分液漏斗Screw chasing machine 螺纹切削机Screw cutting 螺纹切削Screw pitch gauge 螺距规Screw rivet 螺纹铆钉Screw vent 螺杆通孔Rack housing 齿条罩Rack Tubes 油缸Cup Seals Feed Pipes 输油管Spools 卷轴Recuperating Seal(恢复性密封) Inflator Tubes 充气.Cut Seals Steering Hoses 转向胶管Biscuit thickness 料柄厚度注油孔 oil filter point牛皮纸 kraft/brown paper瓦楞纸 fluting paper崩料 charge downslide/collapse卡涉现象 interference phenomenon 机械加工余量 stocking复制模 replaced mould偏心距 offset distance抽大缸 pull tie bar料头 biscuit抽芯 loose core光整平滑度 flatnessDrain cock 排气阀，放出开关Wrench 扳手Stopper 塞子，制动器Intensifier 增强器Check valve 止回阀Orifice 孔，口Pilot valve 领示阀，导阀Cold shut 冷疤，冷结Flow mark 波纹，流线谱Shot stroke 压射冲程Surge pressure 冲击压力，脉动压力Jack bolt 定位螺栓Anchor hole 锚栓孔Dust seal 档尘圈Valve cover 气门盖，阀盖Cylinder tube 汽缸筒Piston rod 活塞杆Piston ring 活塞环Shot cylinder 压射缸Wire clamp 钢丝钳Air hose 空气软管，送风管Atomizer 喷雾器Strainer 滤网Hollow shaft 空心轴，管轴Potentiometer 电位计，分压计Shaft 轴，杆状物Asbestos wire 石棉线Pulley 滑车，滑轮Spring washer 弹簧垫圈Inverter 电源交换器Cutting fluid 切削液refraction coefficient 折光系数Screw Cutting Tap 螺旋切削丝锥plug gauge 塞规color shade色泽red lead power 红丹粉stress relief 去应力casting film 铸型薄膜cast form铸造成形, 铸型cast house crane炉前[出铁场]吊车cast panel铸造面板cast rotor铸造转子cast superalloy铸造高温合金cast test block铸造试块[棒] casting character铸造性能casting crack缩裂casting fin铸件飞边, 铸件披缝, 铸件周缘翅片casting head浇冒口casting lap铸件皱纹casting scar铸疤, 浇注疤casting sealer铸件渗补剂casting strain铸造应变casting stress铸造应力spark plug 火花塞internal-combustion engine cylinder内燃机汽缸hydraulics 水力学pinion小齿轮pinion bearing小齿轮轴承pinion cage主动[行星]齿轮架, 差速器壳, 差速盘pinion cutting machine齿轴切削机床pinion head齿轴齿顶pinion shaped cutter插齿刀pinion spider差速器十字轴pinion stop(起动机的)齿轮停止器valve housing阀套valve actuating mechanism配气机构valve air relief自动放气阀valve bank阀组valve barrel阀缸valve body attachment阀体连接头valve bounce阀跳valve bush阀衬, 阀[衬]套valve chest gasket阀柜垫密片valve cock阀栓valve cottar气阀制销valve disc阀盘valve discharge centrifuge活门卸料式离心机valve follower阀推杆valve positioner阀门定位器分层Delaminationfilling-engine梳丝机器filling agent 填充剂;填料filling auger装载螺旋filling compoun填料filling funnel注液漏斗车架 (car) frame钣金 sheet metal测板 side plate内侧板Inner side plate焊钳soldering turret焊条 welding rod焊点 welding spot焊接机器人 welding robot寿命周期成本 life cycle cost前轴 fore/leading axle后翼子板 rear fender切削性能 cutting characteristic散热性能 heat dispersion耐磨性能 wear resistant property摩擦系数 friction coefficient灰铸铁 gray iron; graphitic cast iron过盈配合 tight/interference fit缸套 cylinder, sleeve, barrel tube pipe导轨面 guide way (face)铣刀盘 face milling cutter/facing cutter刀盘 tool pan/cutter head磨削余量 grinding allowance耐用性 endurance钝化 passivation刀尖圆弧 circular profile of knife point(刀具)主偏角 entering angle; plan angle弹性变形量 amount of elastic deformation燃烧室 combustion chamber磨屑 abrasive dust滤器芯 strainer core差速器 differential gear反冲减震器 recoiling shock absorber废气涡轮 exhaust turbine涡轮增压器 turbocharger增压盲区 turboloch喷油器 oil sprayer/atomizer汽化器 carburetor硬质合金刀具 carbide tipped tool精镗刀具 fine boring tool动力传动系统 power transmission systemspanner 扳子 (美作:wrench)double-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子 (美作:socket wrenchcalipers 卡规pincers, tongs 夹钳wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规hacksaw 钢锯grease gun 注油枪oil can 油壶边刨床 side planer插床 slotting machine车刀 lathe tool车轮车床 car wheel lathe车削 turningBayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Belt drive 带传动Bending machines 弯曲机Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Crimping tools 卷边工具Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Etching machines 蚀刻机Honing machines 搪磨机Lapping machines 精研机Milling heads 铣头Mold polishing/texturing 模具打磨/磨纹Planing machines 刨床aberration 色差atomization 雾化bank mark 料纹bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡centre buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷colour mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹表面处理关联用语时效硬化 age hardening气体硬化 air hardening空气韧化 air patterning退火 annealing阳极效应 anode effect阳极氧化处理 anodizing滚镀 barrel plating滚筒打光 barrel tumbling染黑法 blackening青熟脆性 blue shortness碳酸盐薄膜防锈法 bonderizing箱位退火 box annealing封箱渗碳 box carburizing辉面电镀 bright electroplating光辉热处理 bright heat treatment 旁路热处理 bypass heat treatment 化学电镀 chemical plating化学蒸镀 chemical vapor deposition 大气热处理 controlled atmosphere 锐角效应 corner effect儒缓放电 creeping discharge压花 embossing部分淬火 selective quenching。
压铸模具与成型专业名词(中英文版)
常用软件推荐(Common software recommendation)
Flow 3D / Pro cast Software（US）-目前国内小压铸厂比较多用，因为是免费软件。 Small die casting plant is more commonly used, because it is a free software. Magma-software（Germany）-汽配件大型压铸厂信赖的软件。 This software trusted by large automobile parts company for die casting. Any-casting （Korea）-国内小型压铸厂用的多些。 It was made in Korea, it was more used in the small die casting plant in China.
氮 碳 共 渗 是 在 含 有 活 性 碳 、 氮 原 子 的 介 质 中 同 时 渗 入 氮 和 碳 ， 并 以 渗 氮 为 主 的 低 温 氮 碳 共 渗 工 艺 （ 530℃580℃）。氮碳共渗的渗层脆性小，共渗时间比渗氮时间大为缩短。压铸模经氮碳共渗后，可显著提高其热疲劳性 能。
电镀涂层- Electroplating Coating
Item 1: 模具结构 . Die and Mold
• Prepared by : Danny • Date: 2024-1月
压铸模具零件结构-Mold components.
✓ 前模固定板 Cavity Fixing Plate/ A Plate
✓ 料套 Sprue Bush
模具安装在压铸机上。 Tooling fixed in the die casting machine.
模具名词三语对照表
排气系统设计
排气系统
排气系统是指模具中用于排除型腔内 气体的通道和机构。
排气系统的作用
排气系统的作用是排除型腔内的气体， 避免产品出现气孔、鼓包等问题，提 高产品质量。
排气系统的设计原则
排气系统的设计应遵循结构简单、易 于维护、不影响产品外观等原则。
排气系统的类型
根据产品结构和模具结构，排气系统 可分为自然排气和强制排气两种类型。
分模面设计
01
02
03
04
分模面
模具设计中的分模面是指将模 具分成动模和定模两个部分的
面。
分模面设计原则
分模面设计应遵循便于模具加 工、降低模具复杂度、保证产
品精度等原则。
分模面的类型
根据产品结构和模具结构，分 模面可分为水平分模面、垂直 分模面、倾斜分模面等类型。
分模面的选择
选择合适的分模面可以简化模 具结构，提高模具强度和寿命 ，同时保证产品顺利脱模。
模具名词三语对照表
• 模具类型 • 模具部件 • 模具材料 • 模具设计
01
模具类型
注塑模具
注塑模具：注射成型模，德文：Spritzgussform
英文：Injection Mould
注塑模具主要用于热塑性塑料制品的成型，也可用于热固性塑料制品的 成型，而结构上又具备可调镶件、斜导柱、顶针、司筒、分流器、定位 环、冷却水道等结构。
冲压模具主要用于金属薄板零件的成型，如汽 车覆盖件、家电零件等。冲压模具的结构包括 凹模、凸模、压边圈、定位销等部分。
挤出模具
挤出模具：挤出成型模，德文：Extrusionform
英文：Extrusion Mould 挤出模具主要用于塑料制品的连续成型，如塑料管材、塑料薄膜等。挤出 模具的结构包括机头、口模、芯棒、加热系统等部分。
50个模具专业术语
50个模具专业术语1. 模具 (Mold)2. 塑料模具 (Plastic Mold)3. 金属模具 (Metal Mold)4. 注塑机 (Injection Molding Machine)5. 压铸机 (Die Casting Machine)6. 打磨 (Polishing)7. 铣削 (Milling)8. 钳工 (Machining)9. 精雕 (Engraving)10. 焊接 (Welding)11. 冲压 (Stamping)12. 切割 (Cutting)13. 合模 (Closing)14. 分模 (Opening)15. 导柱 (Guide Pillar)16. 导套 (Guide Bush)17. 滑块 (Slider)18. 塑料件 (Plastic Part)19. 金属件 (Metal Part)20. 模仁 (Core)21. 模腔 (Cavity)22. 底座 (Base)23. 热流道 (Hot Runner)24. 冷却系统 (Cooling System)25. 泵箱 (Pump Box)26. 压缩机 (Compressor)27. 水力缸 (Hydraulic Cylinder)28. 模具钢 (Mold Steel)29. 法兰 (Flange)30. 注塑模具 (Injection Mold)31. 放电加工 (Electrical Discharge Machining)32. 模仁巧妙 (Core Pull)33. 螺旋通道 (Spiral Channel)34. 冷却塔 (Cooling Tower)35. 酸洗 (Acid Etching)36. 布胶 (Rubberizing)37. 文字标记 (Texturing)38. 研磨剂 (Polishing Compound)39. 硅胶 (Silicone)40. 硬度测试 (Hardness Testing)41. 射出速度 (Injection Speed)42. 模具寿命 (Mold Life)43. 热流道系统 (Hot Runner System)44. 冷却时间 (Cooling Time)45. 模具设计 (Mold Design)46. 模具制造 (Mold Manufacturing)47. 模具修理 (Mold Repair)48. 模具改造 (Mold Modification)49. 模具试模 (Mold Trial)50. 模具测试 (Mold Testing)。
压铸机和模具常用语
压铸机和模具常用语冷/热室压铸机cold/hot chamber pressure die-casting machine司筒shot sleeve鎚头piston料壶melting pot sleeve射咀nozzle流道/浇口runner/gate直浇道sprue浇道套sprue bush鹅颈gooseneck压射缸injection cylinder压射冲头injection plunger钢呤steel piston ring排气vent中央熔炉center furnace熔化金属molten metal注料口filling port顶针ejector pin顶针痕ejector pad哥林柱/导柱tie bar前(定)机板/后(动)机板machine platen (moving/fixed)前(定)模/后(动)模cover die half(stationary half)/ ejector die half (moveable half) 冷却水通道water cooling channel样板模prototype die生产模production die成套模unit die组合模sectional die冲模trim die模胚/模肉standardized main die frame/ replaceable cavity units行位/柯(型芯)core slides/core镶件casting insert模具钢热处理die steel heatment模具排位图die layout夹具jig/fixture模具寿命die life浇注系统gating/running system浇注系统设计design of gating system铸件凝固数值模拟numerical simulation of casting solidification铸件工艺计算机辅助设计computer-aided design (CAD) of the casting process 浇口杯pouring cup芯头斜度core taper直浇道spure直浇道窝sprue base横浇道runner内浇道ingate冒口riser/feeder head留型时间/开型时间opening time抽芯机构core puller溢流槽overflow顶针ejector pin垃圾位/余料biscuit /slug锁模力locking force模板尺寸size of die platen回炉料foundry returns废金属料scrap熔/炉渣slag沉/浮渣sludge/dross重熔remelting哥林柱间距/直径space between tie bars/tie bar diameter 开模行位die stroke最大/最小压模厚度maximum/minimum die height干燥周期dry cycle射料力injection force压射位置shot position压射行程injection stroke鎚头直径plunger diameter坩埚容积melting pot专用射料压力specific injection pressure最大压铸面积casting area射料量casting weight顶出力ejector force顶出行程ejector stroke最大压力clamp force max.夹具行程clamp stroke工作压力normal pressure液压系统工作液体gydraulic fluid油箱容积oil tank capacity泵流量/型号pump capacity/type蓄压器型号accumulator type氮气压力nitrogen pressure燃烧装置burning units煤气炉gas furnace燃气炉型号burner type最大输入量Max. input电流强度current电压voltage马达型号/功率motor type/capacity。
压铸常用术语
压铸常用术语（一）压力铸造、压铸机及压铸模一. 压力铸造［压铸］熔融金属在高压、高速条件下，填充模具型腔，并在高压下冷却凝固成型的铸造方法。
二. 压铸机有开合模、压射、抽芯、顶出铸件等机构的压力铸造用机器。
常以锁模力和工作形式表示机器的型号。
三. 热室压铸机压室和压射冲头浸于熔融金属内的压铸机。
压室经鹅颈管与压铸型的浇口连通。
四. 冷室压铸机压室和压射冲头不浸于熔融金属中的压铸机。
将定量的熔融金属浇到压室中，然后进行压射。
五. 冷室卧式压铸机［卧式压铸机］压室水平放置的冷室压铸机。
六. 冷室立式压铸机［立式压铸机］压室垂直放置的冷室压铸机。
压室底面由反冲头形成。
压射时，反冲头下降开启压室射口。
压射后反冲头复位并继续上行，将余料推出压室。
七. 充氧压铸压射前先向型腔中充氧的铝合金压铸法。
由于氧与铝化合，生成细小的氧化铝质点分散于铸件中，因而不会因卷入空气而形成疏松和气孔。
八. 真空压铸先使型腔内造成部分真空，然后压射熔融金属的压铸法。
九. 锁模力在充型过程中，为了保证动、定模相互紧密闭合而施加于模具上的力。
十. 压力中心在平行于锁模力的方向上，溶融合金传递给模具的压力合力的作用点。
十一. 充填速度熔融合金在压力作用下通过内浇口的线速度。
十二. 压射速度压射冲头运动的线速度。
十三. 压射比压充型结束时压射冲头作用于熔融合金单位面积上的压力。
十四. 最大开距压铸机动模、定模安装板之间可分开的最大距离。
十五. 脱模距为取出铸件和浇注系统凝料，动、定模所需的分开距离。
十六. 增压在压射过程最后阶段，压射机构自动开启增压装置，在极短时间内使压射冲头作用在充型金属液上的压力迅速增加。
十七. 压室［压射室］压铸机中用于容纳待压射金属液的圆筒形缸体。
其一端与压铸型连通，由压射冲头将金属液压射入型腔。
十八. 压铸模由定模、动模及金属芯组成的金属模，用于压力铸造成型工艺、成型铸件所使用的模具。
十九. 定模固定在压铸机定模安装板上的模具部分。
压铸常用术语（一）压力铸造、压铸机及压铸模
压铸常用术语（一）压力铸造、压铸机及压铸模一. 压力铸造［压铸］熔融金属在高压、高速条件下，填充模具型腔，并在高压下冷却凝固成型的铸造方法。
二. 压铸机有开合模、压射、抽芯、顶出铸件等机构的压力铸造用机器。
常以锁模力和工作形式表示机器的型号。
三. 热室压铸机压室和压射冲头浸于熔融金属内的压铸机。
压室经鹅颈管与压铸型的浇口连通。
四. 冷室压铸机压室和压射冲头不浸于熔融金属中的压铸机。
将定量的熔融金属浇到压室中，然后进行压射。
五. 冷室卧式压铸机［卧式压铸机］压室水平放置的冷室压铸机。
六. 冷室立式压铸机［立式压铸机］压室垂直放置的冷室压铸机。
压室底面由反冲头形成。
压射时，反冲头下降开启压室射口。
压射后反冲头复位并继续上行，将余料推出压室。
七. 充氧压铸压射前先向型腔中充氧的铝合金压铸法。
由于氧与铝化合，生成细小的氧化铝质点分散于铸件中，因而不会因卷入空气而形成疏松和气孔。
八. 真空压铸先使型腔内造成部分真空，然后压射熔融金属的压铸法。
九. 锁模力在充型过程中，为了保证动、定模相互紧密闭合而施加于模具上的力。
十. 压力中心在平行于锁模力的方向上，溶融合金传递给模具的压力合力的作用点。
十一. 充填速度熔融合金在压力作用下通过内浇口的线速度。
十二. 压射速度压射冲头运动的线速度。
十三. 压射比压充型结束时压射冲头作用于熔融合金单位面积上的压力。
十四. 最大开距压铸机动模、定模安装板之间可分开的最大距离。
十五. 脱模距为取出铸件和浇注系统凝料，动、定模所需的分开距离。
十六. 增压在压射过程最后阶段，压射机构自动开启增压装置，在极短时间内使压射冲头作用在充型金属液上的压力迅速增加。
十七. 压室［压射室］压铸机中用于容纳待压射金属液的圆筒形缸体。
其一端与压铸型连通，由压射冲头将金属液压射入型腔。
十八. 压铸模由定模、动模及金属芯组成的金属模，用于压力铸造成型工艺、成型铸件所使用的模具。
十九. 定模固定在压铸机定模安装板上的模具部分。
压铸专业词汇中英对照表
汉语英語原料硬度一、模胚/模架模胚mold base面板/码模板TP/top clampling plate S45C~S50C底板BP/bottom clamping plate S45C~S50C前模板/定模A/A plate S50C~S55C后模板/动模B/B plate S50C~S55C水口推板RP/striper plate S50C~S55C托板SP/support plate S45C~S50C方铁SB/spacer block S45C~S50C顶针面板ERP/ejector retainer plate S45C~S50C顶针底板EP/ejector plate S45C~S50C吊模环lifting eye bolts SS400隔热板temperature insulator sheets二、模芯/型腔型腔（前模芯/定模芯）master core型芯 (后模芯/动模芯前模镶件cavity insert后模镶件core insert镶件insert镶针insert pins导柱，导杆guide pins SUJ258~65HRC 直导套托司/直司guide bushings SUJ258~65HRC 水口边support pins SUJ258~65HRC 水口边介子support pin collars S45C回针return pins SUJ258~65HRC 地脚distance spacers S45C销dowel SKD61镶针insert pins螺丝杯头螺丝/平面螺丝socket head cap screws SCM43539~44HRC 无头螺丝screw plugs SCM43537~43HRC 拉板tension links S45Cstop bolts SCM43533~38HRC 限位螺丝（水口螺丝拉杆（山打）螺丝puller bolts SCM43533~38HRC 垫圈（介子）washers S45C48~52HRC 弹簧垫圈（介子）spring washer SWRH6242~50HRC 三、浇注系统浇口sprue bushings/drop SK3/SKD6148~52HRC 热嘴hot sprue bushing/ heated nozzles热流道hot runner阀式热流道valve hot runner针点式热流道pin point hot runner冷流道cold runner热流道支撑块hot runner pillar定位环/圈locating rings S45C浇口套/唧嘴弧面gate bushing SKH5159~61HRC 即嘴球头sprue radius四、冷却系统冷却管路cooling line水接头water plug水嘴water line水道堵头cooling circuit plugs集水器water manifold五、顶出系统顶针/顶杆ejector pins直身顶针straight SKH51有托顶针stepped ejector pins SKH51扁顶针blade ejector扁顶rectangular ejector pins SKH51斜顶angular ejector pin / lifter718两次顶出2-step ejector顶出孔knock out推杆stripper bar推方（顶块）ejector block718气顶air pop直身司筒straight ejector sleeves SKD61有身司筒 stepped ejector sleeve SKD61司筒针steps-type center pins SKD61中托司ejector guide bushings SUJ258HRCejector guide pins SUJ258HRC直导柱（中托司用）水口勾针runner lock pins SKH5159~61HRC 水口勾针套bushings for runner lock pin SKH5159~61HRC 六、出模机构脱模斜度draft angle滑块/行位slide行位压条guide rails SKS353-56HRC T型滑块T slide block738行位slide core units七、辅助机构八、排气系统排气阀air poppets镶件排气insert vent气嘴air fitting其它扣鸡ultra locks/ jiff latch lock SK3顺序开关parting lock sets SKD6150~55HRC 胶塞parting locks弹弓coil spring弹弓导柱spring pins S45C水口弹钉runing ejector sets SKH5159~61HRC 弹弓波子ball plungers闸方taper wedges S45C52~56HRC 锥度块taper block sets SKD1158~62HRC 直身定位块locating block sets S45C~S50C50~60HRC 锥形定位块taper block sets S45C~S50C50~60HRC耐磨块（硬度块）wear plates718/73855~62HRC 斜导柱(4~8mm)angular pins DC5360~63HRC 斜导柱(10~40mm)angular pins SUJ258~61HRC 铲鸡locking block SKS353-56HRC 日期嵌入件mold dating inserts718环保标记（镶件）recycling inserts718撑头support pillars S45C撑方spacer blocks S45C垃圾钉stop pins S45C46~50HRC 顶针板顶出限位stop ring S45C46~50HRC 喉咀joint plugs C3604快换喉咀quick fitting joints电子开关switch限位开关limit switch压板holding plates拉板连接圈links rings S45C38~43HRC 吊模梁shipping strap沉孔/玻头，球头counterbore countersink避空位clearance套管bushing分型面parting line分型面锁parting line bolt直边锁straight lock计数器mold shot counter分型面承压块hardened parting line pad撬模角pry bar slot中导柱guided ejection螺丝孔screw hole板销钉(定位销）dowel / knock pin弹簧spring导向杆/复位杆tapped return pin油嘴hydraulic fitting油路集流阀hydraulic manifold锁模块parting line strap定位环locating ring行程开关switch mount蚀纹texture码模槽clamp slot油缸hydraulic clinder导柱guide pin /leader pin螺丝孔screw螺纹tap螺栓,螺杆/插销bolt螺母,螺帽nut铍铜moldmax热电偶thermocouple小柱子boss虎口lock。
压铸模具用语
adjustable spanner 活动扳手 angle cutter 角铣刀anvil 铁钻 arbour 心轴backing 衬垫 belt sander 带式打磨机buffing 抛光 chamfering machine 倒角机chamfering tool 去角刀具 chisel 扁錾chuck 夹具 compass 两角规concave cutter 凹面铣刀 convex cutter 凸形铣刀cross joint 十字接头 cutting edge clearance 刃口余隙角drill stand 钻台 edge file 刃用锉刀file 锉刀 flange joint 凸缘接头grinder 砂轮机 hammer 铁锤hand brace 手摇钻 hatching 剖面线hexagon headed bolt 六角头螺栓 hexagon nut 六角螺帽index head 分度头 jack 千斤顶jig 治具 kit 工具箱lapping 研磨 metal saw 金工锯nose angle 刀角 pinchers 钳子pliers 铗钳 plug 柱塞头polisher 磨光器 protable driller 手提钻孔机punch 冲头 sand paper 砂纸scraper 刮刀 screw driver 螺丝起子scribing 划线 second out file 中纹锉spanner 扳手 spline broach 方栓槽拉刀square 直角尺 square sleeker 方形镘刀square trowel 直角度 stripping 剥离工具T-slot T形槽 tool for lathe 车刀tool point angle 刀刃角 tool post 刀架tosecan 划线盘 trimming 去毛边waffle die flattening 压纹效平 wiper 脱模钳wrench 螺旋扳手air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块 binder plate 压板blank holder 防皱压板 blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁)cavity retainer plate 模穴托板 center pin 中心梢clamping block 锁定块 coil spring 螺旋弹簧cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢 diaphragm gate 盘形浇口die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener 模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck 爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆 drive bearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢ejector plate 顶出板 ejector rod 顶出杆ejector sleeve 顶出衬套 ejector valve 顶出阀eye bolt 环首螺栓 filling core 椿入蕊film gate 薄膜形浇口 finger pin 指形梢finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板 flanged pin 带凸缘?flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧?goose neck 鹅颈管 guide bushing 引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶?冲头 headless punch 直柄冲头heavily tapered solid 整体模蕊盒 hose nippler 管接头impact damper 缓冲器 injection ram 压射柱塞inlay busher 嵌入衬套 inner plunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockout bar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套 lifting pin 起模顶?lining 内衬 locating center punch 定位中心冲头locating pilot pin 定位导梢 locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush 活动衬套making die 打印冲子 manifold block 歧管档块master plate 靠模样板 match plate 分型板mold base 塑胶模座 mold clamp 铸模紧固夹mold platen 模用板 moving bolster 换模保持装置moving bolster plate 可动侧模板 one piece casting 整体铸件parallel block 平行垫块 paring line 分模线parting lock set 合模定位器 pass guide 穴型导板peened head punch 镶入式冲头 pilot pin 导?pin gate 针尖浇口 plate 衬板pre extrusion punch 顶挤冲头 punch 冲头puncher 推杆 pusher pin 衬套梢rack 机架 rapping rod 起模杆re-entrant mold 凹入模 retainer pin 嵌件梢retainer plate 托料板 return pin 回位梢riding stripper 浮动脱模器 ring gate 环型浇口roller 滚筒 runner 流道runner ejector set 流道顶出器 runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝shedder 脱模装置 shim 分隔片shoe 模座之上下模板 shoot 流道shoulder bolt 肩部螺丝 skeleton 骨架slag riser 冒渣口 slide(slide core) 滑块slip joint 滑配接头 spacer block 间隔块spacer ring 间隔环 spider 模蕊支架spindle 主轴 sprue 注道sprue bushing 注道衬套 sprue bushing guide 注道导套sprue lock bushing 注道定位衬套 sprue puller 注道拉料? spue line 合模线 square key 方键square nut 方螺帽 square thread 方螺纹stop collar 限位套 stop pin 止动梢stop ring 止动环 stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套 stripper plate 剥料板stroke end block 行程止梢 submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱 support pin 支撑梢supporting plate 托板 sweep templete 造模刮板tab gate 辅助浇口 taper key 推拔键taper pin 拔锥梢/锥形梢 teeming 浇注three start screw 三条螺纹 thrust pin 推力销tie bar 拉杵 tunnel gate 隧道形浇口vent 通气孔 wortle plate 拉丝模板线切割放电加工关连用语线切割放电加工关连用语abnormal glow 不规则辉光放电 arc discharge 电弧放电belt 皮带 centreless 无心chrome bronze 铭铜 clearance angle 后角corner shear drop 直角压陷 deflection 桡曲度discharge energy 放电能量 dressing 修整dwell 保压 flange 凸缘gap 间隙 graphite 石墨graphite contraction allowance 电极缩小余量 graphite holder 电极夹座hair crack 发裂 horn 电极臂jump 跳刀 magnetic base 磁性座master graphite 标准电极 pipe graphite 管状电极pulse 脉冲 rib working 肋部加工roller electrode 滚轮式电极 rotary surface 旋转面shank 柄部 sharp edge 锐角部tough bronze 韧铜 traverse 摇臂tungsten bronze 钨青铜 waviness 波形起伏work 工件 working allowance 加工余量working dischard 加工废料。
压铸业专业术语(英语)
文案大全Assembly line 组装线 Layout 布置图Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子Electric screw driver 电动起子 Pneumatic screw driver 气动起子 worktable 工作桌 OOBA 开箱检查fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板 barcode 条码barcode scanner 条码扫描器 fuse together 熔合 fuse machine 热熔机 repair 修理 operator 作业员 QC 品管supervisor 课长 ME 制造工程师 MT 制造生技cosmetic inspect 外观检查 inner parts inspect 内部检查 thumb screw 大头螺丝 lbs. inch 镑、英寸front plate 前板traightener 整平机punching machine 冲床 robot 机械手 hydraulic 液压 rear plate 后板 chassis 基座 bezel panel 面板power button 电源按键 reset button 重置键Hi-pot test of SPS 高源高压测试 Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件 plastic parts 塑胶件 SOP 制造作业程序material check list 物料检查表 work cell 工作间 trolley 台车 carton 纸箱 sub-line 支线 left fork 叉车personnel resource department 人力资源部production department 生产部门 planning department 企划部 QC Section 品管科stamping factory 冲压厂 painting factory 烤漆厂 common equipment 常用设备 uncoiler and s machine 油压机 lathe 车床planer |'plein|刨床 miller 铣床 grinder 磨床 driller??床linear cutting 线切割 electrical sparkle 电火花 welder 电焊机staker=reviting machine 铆合机 position 职务 president 董事长general manager 总经理special assistant manager 特助 factory director 厂长 department director 部长deputy manager | =vice manager 副理section supervisor 课长deputy section supervisor =vice section superisor 副课长 group leader/supervisor 组长 line supervisor 线长 assistant manager 助理to move, to carry, to handle 搬运 be put in storage 入库 pack packing 包装 to apply oil 擦油 final inspection 终检 to connect material 接料 to reverse material 翻料 wet station 沾湿台 Tiana 天那水cleaning cloth 抹布 tname of a department 部门名称 a o load material 上料 to unload material 卸料to return material/stock to 退料 scraped |'skræpid|报废 scrape ..v.刮;削deficient purchase 来料不良 manufacture procedure 制程 deficient manufacturing procedure 制程不良oxidation |' ksi'dein|氧化scratch 刮伤 dents 压痕defective upsiding down 抽芽不良 defective to staking 铆合不良 embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力 education and training 教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓 dministration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screwhead螺丝滑头slipped screwhead/shippery screwthread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterpriseexpansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-gradeproducts良品defective products, notup-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模文案大全to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified 不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---tothrow--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece,block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具文案大全figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap 切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetorysecond count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting departmentfor reference会计部存查end-user/using unit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventorylist will be sent to accountingdepartment together (Those of NHKwill be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records ofyear-end physical inventory Listandphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering moldtesting工程试模材料not included in physicalinventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by /prepared by核准/审核/承办PCE assembly production schedulesheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明文案大全part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts 不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆文案大全edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）文案大全top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口文案大全H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection新品首件检查FAA first article assurance 首件确认TVR tool verification report模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process模具制程能力参数SSQA standardized supplierquality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure modeleffectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece InspectionReport 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management文案大全全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original EquipmentManufacture 原设备制造PCE Personal Computer Enclosure个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States ofAmerica 美国文案大全A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic MagnetionInspect 高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll OxideSemiconductor 互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report改善报告NG Not Good 不良WPR Weekly Delivery Requirement周出货要求PPM Parts Per Million 百万分之一文案大全TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material Condition MMS Maximum Material SizeLMC Least Material Condition LMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形 rotaryforging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形 rubber molding橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形 shellcasting 壳模铸造foam forming ?泡成形sinterforging 烧结锻造forging roll 轧锻six sidesforging 六面锻造gravity casting 重力铸造slushmolding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfermolding 转送成形injection molding 射出成形 warmforging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landedplunger mold 有肩柱塞式模具burnishing die 挤光模landedpositive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具 manifolddie 分歧管模具counter punch 反凸模modularmold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswtbending die 双折冷弯模具extrusion die 挤出模 palletizingdie 叠层模family mold 反套制品模具 plastermold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具 pressuredie 压紧模fishtail die 鱼尾形模具 profiledie 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protablemold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavitymold 单腔模具solid forging die 整体锻模 splitforging die 拼合锻模split mold 双并式模具 spruelessmold 无注道残料模具squeezing die 挤压模stretch文案大全form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coilspring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢diaphragmgate 盘形浇口die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆drivebearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin顶出梢ejector plate 顶出板 ejector rod顶出杆ejector sleeve 顶出衬套 ejectorvalve 顶出阀eye bolt 环首螺栓 filling core椿入蕊film gate 薄膜形浇口 finger pin指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧?goose neck 鹅颈管 guide bushing引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶?冲头headlesspunch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injectionram 压射柱塞inlay busher 嵌入衬套innerplunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockoutbar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套liftingpin 起模顶?lining 内衬locating centerpunch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush活动衬套making die 打印冲子manifoldblock 歧管档块master plate 靠模样板matchplate 分型板mold base 塑胶模座 mold clamp 铸模紧固夹mold platen 模用板movingbolster 换模保持装置moving bolster plate 可动侧模板文案大全。
压铸模具术语中英文对照
压铸模具英文对照压力铸造：die casting压铸模具：die-casting die定模：fixed die动模：moving die型腔：cavity分型面：parting line投影面积：project area收缩率：shrinkage锁模力：locking force压力中心：pressure centre充填速度：filling velocity压射速度：injection speed压射比压：injection pressure脱模斜度：draft闭合高度：die shut height最大开距：maximum opening daylight脱模距：stripper distance浇注系统：casting system直浇道：sprue横浇道：runner内浇口：gate溢流槽：overflow well排气槽：air vent定模座板：clamping plate of the fixed half 动模座板：clamping plate of the moving half 定模套板：bolster of the fixed half动模套板：bolster of the moving half支承板：support plat垫块：space block支承柱：support pillar型芯：core活动型芯：movable core螺纹型芯：threaded plug螺纹型环：threaded ring镶块：die insert定模镶块：die insert of the fixed half动模镶块：die insert of the moving half活动镶块：movable insert拼块：split斜销：angle pin弯销：angular cam滑块：slide 型芯滑块：core slide斜滑块：angled sliding split斜槽导板：finger guide plate限位块：stop block楔紧块：wedge block滑块导板：slide guide plate耐磨板：wear pad浇口套：sprue bush分流锥：sprue spreader导流块：baffle排气塞：venting plug排气板：venting plate导柱：guide pillar带头导柱：headed guide pillar带肩导柱：shouldered guide pillar矩形导柱：square guide pillar推板导柱：ejector guide pillar导套：guide bush直导套：straight guide bush带头导套：headed guide bush推板导套：ejector guide bush导板：guide plate推杆：ejector pin圆柱头推杆：ejector pin with a cylindrical head带肩推杆：shouldered ejector pin扁推杆：plat ejector pin成型推杆：forming ejector pin推管：ejector sleecve带肩推管：shouldered ejector sleeve推块：ejector pad推件板：stipping plate推杆固定板：ejector retaining plate推板：ejector plate限位钉：stop pin连接推杆：ejector tie rod推板连接推杆：ejector plate tie rod推板垫圈：ejector plate washer定位元件：locating element冷却环：cooling ring拉料杆：sprue puller pin隔流板：plug bffe。
常用铸造术语中英对照
常用铸造术语中英对照2021-6-26整理(BY BARRY)Ⅰ.根本术语1.压力铸造die casting2.铸造casting,foundry,founding3.铸件casting4.毛坯铸件rough casting5.试制铸件pilot casting6.试模trial shot7.模具mold,mould8.压铸机die casting machine9.铸造设备foundry equipment,foundry facilities10.铸工caster,founder,foundry worker11.压铸工die carter12.铸造厂foundry13.铸造车间foundry shop14.铸造工作者foundry man15.批〔batch一批:a batch;每批:each batch, per batch);lot16.一炉a cast,a heat,a melt17.焊接welding18.铸造三废foundry effluent19.铸锭ingotⅡ.铸造合金、熔炼和浇注1.铸造合金cast alloy2.铝合金aluminium alloy3.铸造复合材料cast composite4.合金元素alloy element5.杂质元素tramp element6.碳化物carbide7.过热superheating8.过冷supercooling9.熔点melting point10.总碳量total carbon11.碳当量carbon equivalent12.碳当量仪eutectometer13.铝硅合金aluminium-silicon alloy14.压铸合金die cast alloy15.压铸铝合金aluminium diecast alloy16.压铸镁合金magnesium diecast alloy17.熔炼smelting18.熔化率melting rate19.元素增加gain of element20.熔剂flux21.熔池bath22.除气熔剂degassing flux23.覆盖剂covering flux24.炉料charging25.金属炉料metallic charging26.回炉料foundry returns 27.废金属料scrap28.熔渣slag29.沉渣sludge30.浮渣dross,scum,cinder31.造渣slag forming32.出渣deslagging33.出渣口slag hole34.炉衬furnace liner35.出炉口tap hole36.出炉温度tapping temperature37.重熔remelting38.坩埚炉crucible furnace39.保温炉holding furnace40.精炼refining41.真空精炼vacuum refining42.除气degassing43.残料heel44.浇注pouring45.自动浇注装置automatic pouring device46.浇包，料斗(勺)ladle47.转运包transfer ladle48.金属残液heel49.冷金属cold matelⅢ铸造工艺与工艺设备die casting process and process device1.铸造性能castability2.流动性fluidity3.充型能力mold-filling capacity4.充型速度(浇注速度)pouring rate;delivery rate5.充型时间filling time6.浇注温度pouring temperature7.比浇注速度specific pouring rate8.浇注时间pouring time9.凝固solidification10.凝固时间solidification11.收缩contraction;shrinkage12.收缩率shrinkage13.液态收缩liquid contraction14.凝固收缩solidification contraction15.固态收缩solid contraction16.液-固收缩liquid-solid contraction17.自由收缩free contraction18.收缩余量shrinkage allowance19.收缩应力contraction stress20.热应力thermal stress21.铸造应力casting stress22.残留应力(剩余应力)residual stress23.热裂倾向性tendency to hot tearing24.铸造工艺设计casting process design25.铸造工艺计算机辅助设计Computer-aided design for the casting process;casting process CAD26.实体造型constructive solid geometry;solid modeling27.充型分析mold filling analysis28.铸造工艺设备设计foundry tools design29.铸造工艺卡casting process card;foundry process card30.铸型装配图mold assembly drawing31.铸件图(毛坯图)drawing of rough casting32.铸造工艺准备preparation of casting technique33.铸件设计casting design34.铸件基准面reference face for machining of casting35.分型面parting face;(mold joint;mold parting)36.不平分型面irregular parting;(irregular joint;match parting)37.阶梯分型面stepped parting;stepped joint38.浇注位置pouring position39.交接壁intersection40.十字交接X-junction41.圆角fillet42.热节(点)hot spot43.加强筋stiffening ribs44.拨模斜度draft45.型腔mold cavity46.工艺孔technological hole47.浇注系统gating system;running system48.直浇道sprue49.横浇道runner50.内浇口ingate,gate51.溢流槽overflow well52.排气槽air vent53.分流锥sprue spreader;spreaderⅣ压力铸造〔特种铸造〕die-casting1.压铸机die casting machine2.冷室压铸机cold chamber die casting machine3.冷室卧式压铸机(卧式压铸机)horizontal(cold chamber)die casting machine4.冷室立式压铸机〔立式压铸机〕vertical(cold chamber)die casting machine5.热室压铸机hot chamber die casting machine6.真空压铸evacuated die casting;vacuum die casting7.压射injection;shot8.压射机构injection system9.压室injection chamber10.压射冲头injection ram;plunger11.压射速度injection speed12.压射比压injection pressure13.增压pressurization 14.充填率rate of filling15.锁型(合型)die locking16.合型机构(锁型机构)die closing mechanism17.锁型力die locking force;clamping force18.拉杆tie bar;tie rod19.压铸模die;die casting die20.定模(定型)fixed die;cover die half21.动模(动型)moving die;ejection die half22.浇口套sprue bush23.留型时间opening time24.顶出机构ejection mechanism25.顶杆ejector pin26.抽芯机构core puller27.余料biscuit;slug28.压铸涂料coating of diecasting;releaseagent29.充型压力mold filling pressure30.充型速度filling speed31.保压压力dwell pressure32.保压时间dwell timeⅤ压铸后加工及其工具1.喷砂清理sand blasting cleaning2.喷丸清理shot blasting cleaning3.抛丸清理wheel blasting cleaning4.滚筒清理tumbling5.抛丸清理机wheel blasting machine6.除浇口degating;trimming7.除毛刺deburring8.去氧化皮descaling9.打磨grinding10.弹丸shot11.抛丸器shot wheel12.喷丸器shot blaster13.砂轮机grinder14.浸渗处理impregnantion15.浸渗剂impregnant16.矫型rectification;straightening coining;17.外表处理surface treatment18.砂带打磨belt sanding19.钻孔;镗孔boring20.脱脂degreasing21.电镀electroplating;electrostatic coating22.夹具clamp;fixture23.机加工machining24.铣milling25.台式铣床bench milling machine26.数控加工中心CNC27.铸件机加工余量machining allowance of casting28.切削液mineral cutting oil29.抛光polishing30.粗加工rough working31.喷涂painting32.冲孔punching33.外表处理surface treatment34.洗净rinse35.车床lathe36.磨床grinder,grinding machine37.铣床milling machine38.钻床drill press39.刨床planerⅥ检测方式/设备/工具量具inspection equipment/facility1.合格质量水平acceptable quality level(AQL)2.气密性试验air tightness test3.大气暴露试验atmospheric corrosion test4.成分分析试验chemical analysis5.破坏性检测destructive inspection6.非破坏性检测nondestructive inspection7.尺寸检测dimensional test8.硬度试验hardness test9.冲击试验impact test10.逐件检查individual check11.抽样检查sampling inspection12.三座标检测microcode13.耐压试验pressure test14.盐雾试验salt spray test15.盐雾试验机salt spray test machine16.拉力测量机tensile test machine17.平面度检测仪flatness inspection guage18.检漏机leakage test machine19.普通检具normal guage20.抽样检查sampling inspection21.耐气候试验weathering test22.x光探伤x-ray test23.X光机X-ray machine24.塞规plug guage25.丝攻screw tap26.锥度规conical guage27.螺纹塞规thread plug guage28.游标卡尺vernier caliper29.半径规radius guage30.测角器/量角器bevel guage31.测径规,厚簿规calliper guage32.高度尺height guage33.深度尺depth guage34.三座标CMM35.光谱仪spectrographⅦ.包装packaging1.护边edge protection2.中间夹层intermediate layer3.多插入口式托盘multiple-entry pallet4.一次性托盘throw-away pallet5.耐气候wether resistanceⅧ图纸相关Drawing Related1.喷砂清理abrasive cleaning2.研磨剂abrasive3.依据according to/Acc to4.阳极氧化anodic oxidation5.外观appearance6.踏板autowalk pallet7.底座基座基准base8.盲孔blind hole9.气孔,气泡blow hole10.孔径hole diameter11.凸台boss12.基准面datum plane13.模定位面cast locator datum plane14.铸造应变casting strain15.中心孔center bore16.外圆角,倒角chamfer17.内圆角fillet18.同心度concentricity19.平面度flatness20.平行度parallel21.粗糙度roughness22.垂直度perpendicularity23.清洁度cleanness24.符合conform to25.残留物，污物contamination26.抽芯孔,铸孔core hole27.耐腐蚀corrosion resistance28.沉孔counterbore29.盖板cover30.关键尺寸critical dimension31.横切试验cross-cut test32.脱炭decarburize33.拔模斜度draft angle/draft34.导电性electric conductivity35.电动扶梯梯级escalator step36.外径〔大径〕external diameter37.内径(小径)internal diameter38.外螺纹external thread39.加工余量machining allowance40.法兰flange41.披锋flash42.自由状态free state43.通用公差〔未注公差〕general tolerance44.符合in accondance with45.来料检验incoming inspection46.标识indication,marking47.绝缘性isolation characteristics48.金属互化物intermetallic compound49.内螺纹internal thread50.每per51.边缘periphery52.永久伸长permanent stretch53.垂直于perpendicular to54.针孔，销孔pin hole55.平面图plan,plane figure56.磨光剂polish agent57.聚酯纤维polyester58.容许应力proof stress59.剩余应力residual stress60.试生产铸件prototype casting61.质量保证quality assurance62.散热器radiator63.耐磨性resistance to abrasion64.肋；筋条rib65.滚丝攻通roll thread thru66.剖面图section67.模具寿命service life of dies68.螺距pitch69.阴影毛坯区域shaded area cast70.收缩shrink71.缩孔shrinkage porosity72.碎片sliver73.烧伤soldering mark74.标准standard/std.75.强度范围strength division76.分层;剥落stripped mark;peeling77.清理外表;外表加工;外表抛光surface finish78.抗拉强度tensile strength79.未注unless otherwise specified/unspecified/unmarked80.凸纹/直纹vein grain81.壁厚wall thickness82.屈服点yield pointⅨ压铸报价Quotation1.适用检测标准acceptable inspection standard2.压铸附加费additional casting cost3.铸造费用casting cost4.折扣价depreciation expenses5.估价estimated price6.离岸价free on board(FOB)7.到岸价cost insurance freight(CIF)8.信用证letter of credit(LC)9.后加工费finishing cost10.定率法fixed rate method11.先行生产go-ahead of produce 12.铝锭价格ingot price13.插件费insert cost14.检测费inspection cost15.熔炼费melting cost16.制造间接(额外)费overhead manufacturing expense17.附加利益profit added18.废品比例rejection percentage19.废品率standard rejection rate20.报废时价值,剩余价值,剩余价值residual value/scrap value21.机器运转费;机器运营本钱running cost of machine22.卖价selling expense23.销售间接费selling overhead24.寿命service life25.(合金)掺合比例standard alloying ratio26.标准价格standard price27.试铸时间time of trial shot28.总价格total cost29.试铸费trial casting cost30.除浇口费trimming cost31.生产yield32.生产率yield rate33.后加工合格率yield rate of finishing34.熔炼生产率yield rate of melting35.压铸成品率overall yield of castingⅩ压铸质量和缺陷casting quality and defect1.废品reject2.化学成分不合格chemical consistenceabnormal3.飞边joint flash4.毛刺veining;burr5.气孔blowhole6.气泡blister7.气泡bubble8.激冷区chill zone9.冷脆性cold shortness10.冷隔cold shut;cold filling11.裂纹crack12.铸点dot13.花纹flower msrk;stripping for shot blast14.外部材料foreign material。
压铸 常用英文词汇 V5
广东文灿压铸有限公司Wencan die casting Co., Ltd常用英语术语列表List of die casting terms and vocabularies( 2011-9-23 re-edit V6)1.新产品以及模具开发products and tooling developing2D/3D drawing 平面图/3维图bump among products 货与货之间碰撞capital equipment 资本设备, 固定设备chamfering倒角classification 分类、级别datums 基准datum level 基准水平面datum line 基准线datumplane 【测】基(准)面design/process FMEA D设计/P过程FMEAdie casting 压铸die fabrication 模具加工Die location layout 工模排位图Die polished 省模Die trial 试模electrode for EDM 放电用铜公machining by CNC wire-cut machine 线切割加工machining by electric discharge machine ( EDM ) 电蚀火花加工potential effects of failure 潜在失效后果potential failure mode 潜在失效模式rib and corner 筋肋和尖角subcontractor 外包商set die-casting parameter/locking force/ injection force/injection velocity/shot time/ volume of release agent/die-open time/ ejector time/pressure rating/metal temperature/ control temperature/ operation according to WI按工作指示设定压铸参数/锁模力/射料力/射料速度/打锤时间/喷雾量/开模时间/顶出时间/压力参数/料温/控制温度/按照作业指导书作业；thermal expansion 热膨胀2．热处理heat treatmentair cooling 空气冷却annealing 退火carbonization 碳化case hardening 表面硬化，表面淬硬full annealing 完全退火heat treatment 热处理metallographic structure 金相组织metallographic test 金相试验quenching 淬火residual stress 残余应力tempering 回火3．压铸设备及模具die casting machine and die toolingangle pin 斜导销biscuit /slug 料饼/余料blister 气泡burner 燃烧器casting area最大压铸面积casting insert 铸件镶件casting fin铸件飞边, 铸件披缝, 铸件周缘翅片cavity fill time 充型时间cavity insert 型腔镶块cavity 型腔center furnace 中央熔炉clamp force max. 最大压力coefficient 系数cold chamber machine 冷压室压铸机cold/hot chamber pressure die-casting machine 冷/热室压铸机contraction 收缩core slides/core 活动抽芯（型芯）cover die half(stationary half )/ ejector die half (moveable half ) 前（定）模/后（动）模crucible furnace 坩埚炉crucible pot 坩埚degassing 除气/去气delivery rate；pouring rate 充型流速/浇注速度design of gating system 浇注系统设计die layout模具排位图die life 模具寿命die stroke 开模行程draft 拔模斜度ejector force顶出力ejector pad 顶针痕ejector pin 顶针ejector stroke 顶出行程feeding 补缩foundry returns 回炉料gating/running system 浇注系统holding furnace 保温炉ingate 内浇道injection plunger 压射冲头ladle 浇包locking force 锁模力machine platen 压铸机模板moving/fixed platen 动/定模板maximum/minimum die height 最大/最小压模厚度metal fluidity （金属）流动性molten metal 熔化金属nitrogen pressure 氮气压力normal pressure工作压力numerical simulation of casting solidification 铸件凝固数值模拟opening time 留型时间/开型时间overflow 溢流槽/ 渣包production die 量产模prototype die 样板模refining 精炼refining agent 精炼剂remelting 重熔riser/feeder head 冒口runner 横浇道runner/gate 流道/浇口scrap 废金属料secondary alloy 再生合金shot sleeve 司筒,压射室size of die platen 模板尺寸slag 熔/炉渣sludge/dross 沉/浮渣solidification 凝固sprue pin（spreader）直浇道锥（分流器）spure 直浇道die frame 模架tangential runner 切向横浇道tie bar 哥林柱/导柱/拉杆total melting loss 熔炼损耗率熔损、烧损trim die 冲模vent 排气口water cooling channel 冷却水通道4．压铸工艺与后加工工艺die casting and secondary process alloy component assay report 合金成份化验报告appearance外观center furnace 中央溶炉characteristics 特性degating 冲水口die casting 压铸parting line 分型线polishing/buffing 磨/抛光polishing 抛光、磨光polishing/cotton wheels 抛光用布轮removing burrs round pads of ejector pin 刮项针位批锋removing parting line flash 磨分型线sanding wheels 砂布轮5．精加工工艺machining processboring 镗精加工fine maching ; 粗加工rough maching drill bit 钻头卧式加工中心Horizontal machining center chuck 车床卡盘，夹具立式加工中心vertical machining center cutting tools刀具external/internal thread 外/内螺纹file 锉form tool 成型刀grind 磨jig/fixture 夹具lathe 车床left-hand thread左旋螺纹length of thread engagement螺纹旋合长度loose thread滑牙machining accuracy加工精度machining allowance of casting 铸件机械加工余量machining allowance加工余量machining error加工误差mandrel 机加工芯轴mill 铣minor diameter小径parallel screw thread圆柱螺纹pitch diameter中径pitch螺距plane 刨,Reaming铰孔right-hand thread 右旋螺纹rolled threads 挤牙root diameter底径screw thread 螺纹tapping 攻牙tight thread牙紧uncompleted tapping 牙不完整6．表面处理surface treatmenta mixture of 2 parts water and 3 parts oil 2分水3分油混合acid dip/pickling 酸洗acid 酸水alkali cleaning 碱洗Anodizing 阳极氧化baking 烘干blueing /chemical oxide 钢铁发蓝/化学氧化chemical pretreatment 化成处理chromating 铬化clear black e-coatings透明黑色泳漆clear chroming 无色铬化colored passivation 彩色钝化concentration 浓度dedusting 除尘degreasing 脱脂，除油descaling 刻蚀dipping 浸渍electrophoresis 电泳electrophoretic coating 电泳漆electroplating hard chrome 镀硬铬electrostatics powder coatings 静电粉沫喷涂E-plating 电镀hexavalent chromium 六价铬impregnation 浸渗mechanical polishing机械抛光neutralization 中和PAD printing/silk screening 移印/丝印passivating 钝化phosphating 磷化resin 树脂rinsing 过清水Roughtening 粗化spray powder 喷粉taking down 下挂trivalent chromium 三价铬ultrasonic clean 超声波清洗wiping with toluene 抹天那水salt spray testing 盐雾试验7．品质控制quality controlappearance full-inspection 外观全检collection 回收evaluation / measurement technique 评价/测量技术first inspection for 5 shots 首检5件Freq=frequency 次数incoming quality sampling inspection report 来料质量抽查报告interprocess quality sampling inspection report 工序间质量抽查报告pile products up due to laying in disorder 摆放不正确堆积产品processing tour-inspection 制程巡回检查product/process specification /tolerance 产品/过程规范/公差projector 投影仪QC tour-inspection QC巡检quality final-inspection report 最终检验质量报告quality first piece inspection report 质量首件检查报告quality traceability analysis report 质量追踪分析表return to supplier 退回供应商sampling inspection 抽检self-inspection 自检Special Char. class 特殊特性分类spot check 抽样检查visual standard 外观标准workmanship standard 工作质量标准8.质量缺陷常用语defectsair tightness 气密性blister/pimple/bubble 起泡bumps 碰伤caniniform/dentate狗牙casting fin铸件飞边, 铸件披缝, 铸件周缘翅片cold lap 冷隔cold shut 冷纹Contamination 污染dirt pits 尘点distortion/deformation 变形double skin 重皮ejector marks raised or depressed 顶针位凹凸elephant skin皱皮entrapped slag；slag inclusion 夹渣filling to excess 多料flow mark 流痕/波纹flow lineincomplete filling 缺料incorrect casting form 形状不合格indentation 印痕/凹痕internal quality of casting 铸件内在质量micro-shrinkage；porosity 疏松【显微疏松】off dimension；off size 尺寸不合格oil marks 油渍orange peel 桔皮缺陷out of size 尺寸不符oxidation 氧化partial breakage of a casting 崩料peeling 电镀脱皮pinhole针孔pits 面麻porosity 砂孔roughness 粗糙sand inclusion 砂眼scratches 划痕/刮伤shrinkage 缩水slag 炉渣stain 污渍texturing 致密性thermal shrinkage crack （on product）(产品中的)热缩裂raised crack mark line (on product) (产品表面凸起的龟裂线) visual quality of casting 铸件外观质量void 砂眼/气孔warpage 挠曲yellowing发黄yield of casting 铸件合格品率missrun 欠铸9. 压铸件试验常用语testingadhesion 附着性deflection 挠度elastoplasticity 弹塑性elongation 延伸率extend 延伸film thickness 涂膜厚度film thickness gauge 膜厚仪flexibility 屈曲挠性hardness 硬度heat impact test 热冲击试验high humidity test 高湿测试humidity resistance 耐湿impact resistance 抗冲击力impact strength 冲击性measuring adhesion by tape test 胶带附着力测试neutral salt-spray NSS test 中性盐雾residual stress 残余应力spraying viscosity 喷涂粘度strengthen 加强、巩固tension 拉紧、张力viscosity 粘度water resistance 耐水性yield strength 屈服强度mechanical property 力学性能chemical analysis 化学成份10.测量工具常用语measurement and gauge Altitude gauge 高度仪average 平均值Block Gauge 块规Bore Gauge 孔规Clearance gauge 塞尺/间隙规CMM 三坐标测试仪Depth Micrometer 深度千分尺Digital caliper 电子卡尺Digital Height Gauge 数字高度测量仪durometer/hardness meter 硬度计Electric/digital Balance 电子称Electroplating THK.Tester 电镀厚度测试仪equipment variation 设备变差gage repeatability and reproducibility report 量具的R&R重复性和再现性报告go-no-go gauge “过” -- “不过” 验规通-止规HRC/HV Hardness Tester 洛/维氏硬度仪Rockwell testingimpact tester 冲击仪Inside/outer Micrometer 内/外径千分尺measurement unit analysis 测量设备分析Micrometer Calipers 千分卡尺Microscope 显微镜metallographic microscope 金相显微镜Multimeter 万用表electric universal testing 电子万能试验机normal distribution curve 正态分布曲线number of parts 零件数量number of trials 实验次数one range 单极差part variation 零件变差pin gauge 针规Plug gage 塞规Projector 投影仪Optical image 光学影像测量仪range 公差带range control chart 极差控制图repeatability 重复性reproducibility再现性Ring Gauge 环规spectrometer 光谱仪Thermometer 温度计Thread Gauge 螺纹规thread plug gage螺纹塞规Torque Meter 力矩计total variation 总变差Twisting Meter 转扭力仪Vernier Caliper 游标卡尺viscosimeter 粘度计visual check 目测witness mark (测量)参考(标)点endoscope 内窥镜11. 形位公差常用语toleranceangularity 倾斜度角度aperture 孔径basic dimension 基本尺寸basic size 基本尺寸c/c =between centers 中心距centricity中心circular runout 圆跳动circularity 圆度roundnessconcentricity 同轴度同心度conical 圆锥形的coordinate data 坐标数据coordinate dimensioning 坐标尺寸cylindricity 圆柱度datum/feature/point/line/ plane/axis 基准/特征/点/线/平面/轴线deviation偏差diameter/radius 直径/半径draft angle 拔模斜度ellipse 椭圆excentricity 偏心距（率）flatness 平面度geometric dimensioning 几何尺寸fit/clearance fit/interference fit/ transition fits 配合/间隙配合/过盈配合/过渡配合M/LMC=maximum/least material condition 最大/小材料状态nominal diameter 公称直径oblong 长方形oblong hole 椭圆孔ovality 圆锥度（变形）parallelism 平行度perpendicularity 垂直度position 位置度profile of a line 线轮廓度profile of a surface 面轮廓度reference frame 坐标系right angle 直角rounds/fillets draft 外圆角/内圆角拔模斜度square 正方形standard/ precision tolerance 标准/精度公差straightness 直线度symmetry 对称度theoretical size 理论正确尺寸thickness厚度tolerance/value 公差/值top/side/ end view 顶/测/端视图total runout 全跳动unilateral/bilateral tolerance 单/双边公差upper/lower deviation 上/下偏差12.包装和包装材料packagebar code 条形码blister plate/PVC tray 吸塑罩bubble bag 气泡袋closed /sealed poly bag 封口胶袋corrugated cardboard/sheet波纹隔板corrugated egg-crate carton 瓦楞蛋格卡通箱foam bag 珍珠棉袋forktruck 叉车GW gross weight /NW net weight 毛/凈重If wooden pallet, the certificate of disinfection for pallet 如果是木制卡板要有卡板消毒熏蒸证明in egg tray with carton packages 卡通箱及其蛋格item/ sales consumer pack 单件装label 包装标识logo polybag 有唛胶袋multipack 多件装outside dimensions 长x宽x高length x width x height 外部尺寸packaging materials 包装材料packaging strapping/PP-straps包装带pad separator; clapboard; partition board/sheet 隔板pallet 卡板plastic container 胶箱shrinkage package 吸塑包装single/double/3 regular slotted carton/box 单/双/三坑纸箱styrofoam 聚苯乙烯泡沫塑料白色泡沫tissue papper 拷贝纸transparent plastic film circle the pallet/stretch poly wrap 透明膜保鲜纸unitload pallet 整卡装wrappage 包装材料13.生产控制计划production controlcontrol plan 控制计划core team 核心小组date Rev. 日期修订date orig. 日期编制each batch 每批Inform line/team leader/ supervisor/manager to shut down and recheck 通知生产拉/组长/主管/经理，停机再检查machine adjustment 调机machine, device, jig, tools for Mfg. 生产工艺装备material identification 物料标识mounting die 安装模具mounting die inspection sheet 模具安装检查清单once every operation每次开机part /process number 零件/过程编号part name/description 零件名称/描述pre-launch 试生产process 过程process name/operation description 过程名称/操作描述reaction plan 反应计划refer to CP 参考控制计划14.优质浇口设计七步法gate design优质浇口设计七步法The Seven Steps To A Quality Gating Design第一步确定铸件质量等级。
压铸模国标
压铸模具国家标准（GB/T 8847 2003、GB/T 8844 2003）压铸模标准（国标2003）一、压铸模术语 GB/T 8847 20031 范围本标准界定了有关压铸模的常用术语。
本标准适用于压铸模常用术语的理解和使用。
2 一般术语2.1 压力铸造 die casting将熔融合金在高压、高速条件下填充模具型腔，并在高压下冷却凝固成型的铸造方法。
2.2 压铸模 die-casting die压力铸造成型工艺中，用以成型铸件所使用的模具。
2.3 定模 fixed die固定在压铸机定模安装板上的模具部分。
2.4 动模 moving die随压铸机动模安装板开合移动的模具部分。
2.5 型腔 cavity模具闭合后用以充填熔融合金，成型铸件的空腔。
2.6 分型面 parting line模具上为取出铸件和浇注系统凝料可分离的接触表面。
2.7 投影面积 proieot area模具型腔、浇注系统及溢流系统在垂直于锁模力方向上投影的面积总和。
2.8 收缩率 shrinkage在室温下，模具型腔与铸件的对应线性尺寸之差和模具型腔对应线性尺寸之比。
2.9 锁模力 locking force在充型过程中，为了保证动、定模相互紧密闭合而施加于模具上的力。
2.10 压力中心 pressure centre在平行于锁模力的方向上，熔融合金传递给模具的压力合力的作用点。
2.11 充填速度 filling velocity熔融合金在压力作用下通过内浇口的线速度。
2.12 压射速度 injection speed压射冲头运动的线速度。
2.13 压射比压 injection pressure充型结束时压射冲头作用于熔融合金单位面积上的压力。
2.14 脱模斜度 draft为了使铸件顺利脱模，在模具型腔壁沿脱模或抽拔方向上设计的斜度。
2.15 闭合高度 die shut height模具处于闭合状态下的总高度。
2.16 最大开距 maximum opening daylight压铸机动模、定模安装板之间可分开的最大距离。
压铸用语中英词汇表
壓鑄用語中英詞彙表Accumulator: 蓄壓器在油壓迴路上用來儲存油壓動力來源之壓力油的容器。
Accumulator Charge: 蓄壓器充填通常指蓄壓器內部所充填的氮氣量。
Area,Vent: 排氣面積排氣槽的截面積或全部模腔的總排氣面積。
Automatic Operation: 自動操作表達一部壓鑄機連續操作不需要操作員去啟動每一次循環的用語。
Bushing: 襯套以軸銷相配的圓柱筒套。
Bushing,Clearance: 襯套間隙襯套內徑與軸銷外徑之配合公差。
Bushing,Guide Pin: 導銷襯套與導銷配合的襯套。
Casting: 鑄件熔解的金屬在模具內凝固成形的產品。
Casting,Cycle: 鑄造循環或過程以壓鑄而言，通常包括凝固時間、機器動作和順序時間。
Casting,Defect: 鑄件缺陷任何一項不能滿足鑄件的設計或品質標準之要點的缺陷。
Casting,Defective: 鑄件不良沒有達到設計或品質規格要求的鑄件。
Casting Rate: 鑄造效率機器持續運行一小時所鑄造的平均射次。
Casting Removal: 鑄件取出將固化成形的鑄件從開啟的模具上拿出的動作。
Casting Section Thickness: 鑄件剖面厚度鑄件的壁厚。
Casting Shrinkage: 鑄件收縮量鑄件在模具中固化成形時與冷卻至室溫時的每一個單位長度尺寸之變化量。
Casting,Temperature: 鑄造溫度在射出時的鑄造溫度。
Casting,Thickness: 鑄件厚度鑄件的剖面厚度。
Casting,Thin Wall: 薄壁鑄件定義一個鑄件滿足功能需求之最小壁厚的用語。
Casting,Volume: 鑄件容積鑄件中金屬的總立方單位（例如：立方英吋或立方公分）。
Cavities,Multiple: 多模穴一副模具上有一個以上的模穴。
Cavity: 模穴壓鑄模具上用來鑄造零件外形尺寸的空間。
模具工程常用词汇
模具工程常用词汇模具工程常用词汇die模具figurefile,chartfile图档cuttingdie,blankingdie冲裁模progressivedie,follow(-on)die连续模compounddie复合模punchedhole冲孔panelboard镶块tocutedges=sidecut=sidescrap切边tobending折弯topull,tostretch拉伸Linestreching,linepulling线拉伸engraving,toengrave刻印upsidingdownedges翻边tostake铆合designmodification设计变化dieblock模块foldedblock折弯块slidingblock滑块locationpin定位销liftingpin顶料销dieplate,frontboard模板paddingblock垫块steppingbar垫条upperdiebase上模座lowerdiebase下模座uppersupportingblank上承板upperpaddingplateblank上垫板sparedies模具备品spring弹簧bolt螺栓plate电镀mold成型materialforengineeringmoldtesting工程试模材料notincludedinphysicalinventory不列入盘点incomingmaterialtobeinspected进货待验PCEassemblyproductionschedulesheetPCE组装厂生产排配表model机锺workorder工令revision版次productioncontrolconfirmation生产确认checkedby初审approvedby核准stockageanalysissheeton-handinventory现有库存availablematerial良品可使用obsoletematerial良品已呆滞tobeinspectedorreworkedcausedescription原因说明partnumber/P/Nitem/group/class类别preparedby制表year-endphysicalinventorydifferenceanalysissheetphysicalinventory盘点数量physicalcountquantity 帐面数量differencequantity差异量goodproduct/acceptedgoods/acceptedparts/goodparts良品defectiveproduct/non-goodparts不良品disposedgoods处理品onwaylocation在途仓oversealocation海外仓sparepartsphysicalinventorylist备品盘点清单sparemoldslocation模具备品仓skid/pallet栈板toxmachine自铆机wireEDM线割EDM放电机coilstock卷料sheetstock片料tolerance工差score=groove压线camblock滑块pilot导正筒trim剪外边pierce剪内边dragform压锻差pocketforthepunchhead挂钩槽slughole废料孔featuredie公母模expansiondwg展开图radius半径shim(wedge)楔子torch-flamecut火焰切割setscrew止付螺丝formblock折刀stoppin 定位销roundpiercepunch=diebutton圆冲子shapepunch=dieinsert异形子stocklocaterblock定位块undercut=scrapchopper清角activeplate活动板baffleplate挡块coverplate盖板maledie公模femaledie母模groovepunch压线冲子air-cushioneject-rod气垫顶杆spring-boxeject-plate弹簧箱顶板bushingblock衬套insert入块capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂mainmanifold主集流脉bezel斜视规blanking穿落模dejecting 顶固模demagnetization去磁;消磁high-speedtransmission高速传递heatdissipation热传rack上料degrease脱脂rinse水洗alkalineetch龄咬desmut剥黑膜D.I.rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次partnumber/P/N料号goodproducts良品scrapedproducts报放心品defectiveproducts不良品finishedproducts成品disposedproducts处理品barcode条码flowchart流程表单assembly组装stamping冲压molding成型spareparts=buffer备品coordinate座标dismantlethedie折模auxiliaryfuction辅助功能poly-line多义线heaterband加热片thermocouple热电偶sandblasting喷沙grit砂砾derustingmachine除锈机degate打浇口dryer烘干机induction感应inductionlight感应光response=reaction=interaction感应ram连杆edgefinder巡边器concave凸convex凹short射料不足nick缺口speck瑕疵shine亮班splay银纹gasmark焦痕delamination起鳞coldslug冷块blush导色gouge沟槽;凿槽satintexture段面咬花witnessline证示线patent专利grit沙砾granule=peuet=grain细粒gritmaker抽粒机cushion 缓冲magnalium镁铝合金magnesium镁金metalplate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-holeform通孔形式vollerpinformality滚针形式camdriver铡楔shank摸柄crankshaft曲柄轴augularoffset角度偏差velocity速度productiontempo生产进度现状torque扭矩spline=themultiplekeys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungstenhighspeedsteel钨高速的molyhighspeedsteel钼高速的organicsolvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机plaindie简易模piercedie冲孔模formingdie成型模progressivedie连续模gangdies复合模shearingdie剪边模rivetingdie铆合模pierce冲孔forming成型(抽凸,冲凸)drawhole抽孔bending折弯trim切边emboss 凸点dome凸圆semi-shearing半剪stampmark冲记号deburrorcoin压毛边punchriveting冲压铆合sidestretch侧冲压平reelstretch卷圆压平groove压线blanking下料stampletter冲字(料号)shearing剪断tick-marknearside正面压印tick-markfarside反面压印extensiondwg展开图proceduredwg工程图diestructuredwg模具结构图material材质materialthickness料片厚度pressspecification冲床规格dieheightrange适用模高dieheight闭模高度burr毛边gap间隙punchwt.上模重量innerguidingpost内导柱innerhexagonscrew内六角螺钉dowelpin固定销coilspring弹簧lifterpin顶料销eq-heightsleeves=spool等高套筒pin销lifterguidepin浮升导料销guidepin导正销wirespring圆线弹簧outerguidingpost外导柱stopscrew止付螺丝locatedpin定位销outerbush外导套topplate上托板（顶板）topblock上垫脚punchset上模座punchpad上垫板punchholder上夹板stripperpad脱料背板upstripper上脱料板maledie公模(凸模)featuredie公母模femaledie母模(凹模)upperplate上模板lowerplate下模板diepad下垫板dieholder下夹板dieset下模座bottomblock下垫脚bottomplate下托板(底板)strippingplate内外打(脱料板)outerstripper外脱料板innerstripper内脱料板lowerstripper下脱料板punch冲头insert入块(嵌入件)deburringpunch压毛边冲子groovepunch压线冲子stampedpunch字模冲子roundpunch圆冲子specialshapepunch异形冲子bendingblock折刀roller滚轴baffleplate挡块locatedblock定位块supportingblockforlocationaircushionplate气垫板air-cushioneject-rod气垫顶杆trimmingpunch 切边冲子stiffeningribpunch=stinger加强筋冲子ribbonpunch压筋冲子reel-stretchpunch卷圆压平冲子guideplate定位板slidingblock滑块slidingdowelblock滑块固定块activeplate活动板lowerslidingplate下滑块板upperholderblock上压块uppermidplate上中间板springbox弹簧箱spring-boxeject-rod弹簧箱顶杆spring-boxeject-plate弹簧箱顶板bushingbolck衬套coverplate 盖板guidepad导料块&模具相关英文compresionmolding压缩成型flashmold溢流式模具plsitivemold挤压式模具splitmold分割式模具cavity型控母模core模心公模taper锥拔leathercloak 仿皮革shiver饰纹flowmark流痕weldingmark溶合痕postscrewinsert螺纹套筒埋值selftappingscrew自攻螺丝striperplate脱料板piston活塞cylinder汽缸套chip细碎物handlemold手持式模具encapsulationmolding低压封装成型twoplate两极式（模具）welltype蓄料井insulatedrunner绝缘浇道方式hotrunner热浇道runnerplat浇道模块valvegate阀门浇口bandheater环带状的电热器spindle阀针spearhead刨尖头slagwell冷料井coldslag冷料渣airvent 排气道weldingline熔合痕ejectpin顶出针knockpin顶出销returnpin回位销反顶针sleave套筒stripperplate脱料板insertcore放置入子runnerstripperplate浇道脱料板guidepin导销ejectrod(bar)（成型机）顶业捧subzero深冷处理threeplate三极式模具runnersystem浇道系统stresscrack应力电裂orientation定向spruegate射料浇口，直浇口nozzle射嘴spruelockpin料头钩销(拉料杆)slagwell冷料井sidegate侧浇口edgegate侧缘浇口tabgate搭接浇口filmgate薄膜浇口flashgate闸门浇口slitgate缝隙浇口fangate扇形浇口dishgate因盘形浇口diaphragmgate隔膜浇口ringgate环形浇口subarinegate潜入式浇口tunnelgate隧道式浇口pingate针点浇口Runnerless无浇道(sprueless)无射料管方式longnozzle延长喷嘴方式sprue浇口;溶渣accuratediecasting精密压铸powderforming粉末成形calendaringmolding压延成形powdermetalforging粉末锻造coldchamberdiecasting冷式压铸precisionforging精密锻造coldforging冷锻pressforging冲锻compactingmolding粉末压出成形rockingdieforging摇动锻造compoundmolding复合成形rotaryforging回转锻造compressionmolding压缩成形rotationalmoldingdipmold浸渍成形rubbermolding橡胶成形encapsulationmolding注入成形sandmoldcasting砂模铸造extrusionmolding挤出成形shellcasting壳模铸造foamforming泡沫成形sinterforging烧结锻造forgingroll轧锻sixsidesforging六面锻造gravitycasting重力铸造slushmolding凝塑成形hollow(blow)molding中空(吹出)成形squeezecasting高压铸造hotchamberdiecasting热室压铸swaging挤锻hotforging热锻transfermolding转送成形injectionmolding射出成形warmforging温锻investmentcasting精密铸造matcheddiemethod对模成形法laminatingmethod被覆淋膜成形lowpressurecasting低压铸造lostwaxcasting脱蜡铸造matchedmouldthermalforming对模热成形模bismuthmold铋铸模landedplungermold有肩柱塞式模具burnishingdie挤光模landedpositivemold有肩全压式模具buttondie镶入式圆形凹模loadingshoemoldcenter-gatedmold中心浇口式模具loosedetailmold活零件模具chillmoldloosemold活动式模具clodhobbing冷挤压制模louveringdie百叶窗冲切模compositedies复合模具manifolddie分歧管模具counterpunch反凸模modularmold组合式模具doublestackmold双层模具multi-cavitymold多模穴模具electroformedmold电铸成形模multi-gatemold复式浇口模具expanderdie扩径模offswtbendingdie双折冷弯模具extrusiondie挤出模palletizingdie叠层模familymold反套制品模具plastermold石膏模blankthroughdies漏件式落料模porousmold通气性模具duplicatedcavityplate复板模positivemold全压式模具fantaildie扇尾形模具pressuredie压紧模fishtaildie鱼尾形模具profiledie轮廓模flashmold溢料式模具progressivedie 顺序模gypsummold石膏铸模protablemold手提式模具hot-runnermold热流道模具prototypemold雏形试验模具ingotmold钢锭模punchingdie落料模lancingdie切口模raising(embossing)压花起伏成形re-entrantmold倒角式模具sectionaldie拼合模runlessinjectionmold无流道冷料模具sectionaldie对合模具segmentmold组合模semi-positivemold半全压式模具shaper定型模套singlecavitymold单腔模具solidforgingdie整体锻模splitforgingdie拼合锻模splitmold双并式模具spruelessmold无注道残料模具squeezingdie挤压模stretchformdie拉伸成形模sweepingmold平刮铸模swingdie振动模具threeplatesmold三片式模具trimmingdie切边模unitmold单元式模具universalmold通用模具unscrewingmold退扣式模具yoketypedie轭型模airventvale通气阀anchorpin锚梢angularpin角梢baffle调节阻板angularpin倾斜梢baffleplate折流档板ballbutton球塞套ballplunger定位球塞ballsliderbinderplate压板blankholder防皱压板blankingdie落料冲头bolsterbottomboard浇注底板bolster垫板bottomplate下固定板bracket托架bumperblock缓冲块buster堵口castingladle浇注包castinglugcavity模穴(模仁)cavityretainerplate模穴托板centerpin中心梢clampingblock锁定块coilspring螺旋弹簧coldpunchednut冷冲螺母coolingspiralcore心型corepin心型梢cotter开口梢cross十字接头cushionpindiaphragmgate盘形浇口dieapproach模头料道diebed型底dieblockdiebody铸模座diebush合模衬套diebutton冲模母模dieclamper夹模器diefastener模具固定用零件dieholder母模固定板dielip模唇dieplate冲模板dieset冲压模座directgate直接浇口dogchuck爪牙夹头dowel定位梢dowelhole导套孔dowelpin合模梢dozzle辅助浇口dowelpin定位梢draft拔模锥度drawbead张力调整杆drivebearing传动轴承ejectionpad顶出衬垫ejector脱模器ejectorguidepin顶出导梢ejectorleaderbusher顶出导梢衬套ejectorpad顶出垫ejectorpin顶出梢ejectorplate顶出板ejectorrod顶出杆ejectorsleeveejectorvalve顶出阀eyebolt环首螺栓fillingcore椿入蕊filmgatefingerpin指形梢finishmachinedplate角形模板finishmachinedroundplate圆形模板fixedbolsterplate固定侧模板flangedpin带凸缘销flashgate 毛边形浇口flask上箱floatingpunch浮动冲头gate浇口gateland浇口面gib凹形拉紧楔gooseneck 鹅颈管guidebushing引导衬套guidepin导梢guidepost引导柱guideplate导板guiderail导轨headpunch顶头冲孔headlesspunch直柄冲头heavilytaperedsolid整体模蕊盒hosenippler管接头impactdamper缓冲器injectionram压射柱塞inlaybusher嵌入衬套innerplunger内柱塞innerpunch 内冲头insert嵌件insertpin嵌件梢kingpin转向梢kingpinbush主梢衬套knockoutbar脱模杵land合模平坦面landarea合模面leaderbusher导梢衬套liftingpin起模顶销lining内衬locatingcenterpunch 定位中心冲头locatingpilotpin定位导梢locatingring定位环lockblock压块lockingblock定位块lockingplate定位板loosebush活动衬套makingdiemanifoldblock歧管档块masterplate靠模样板matchplate分型板moldbase塑胶模座moldclamp铸模紧固夹moldplaten模用板movingbolster换模保持装置movingbolsterplate可动侧模板onepiececasting整体铸件parallelblockparingline分模线partinglockset合模定位器passguide穴型导板peenedheadpunch镶入式冲头pilotpin导销pingate针尖浇口plate衬板preextrusionpunch顶挤冲头punch冲头puncher推杆pusherpin衬套梢rack机架rappingrod起模杆re-entrantmold凹入模retainerpin嵌件梢retainerplate托料板returnpin 回位梢ridingstripper浮动脱模器ringgate环型浇口roller滚筒runner流道runnerejectorset流道顶出器runnerlockpin流道拉梢screwplug头塞setscrew固定螺丝shedder脱模装置shim分隔片shoe 模座之上下模板shoot流道shoulderbolt肩部螺丝skeleton骨架slagriser冒渣口slide(slidecore)滑块slipjoint滑配接头spacerblock间隔块spacerring间隔环spider模蕊支架spindle主轴sprue注道spruebushingspruebushingguide注道导套spruelockbushing注道定位衬套spruepullerspueline合模线squarekey方键squarenut方螺帽squarethreadstopcollar限位套stoppin止动梢stopring止动环stopper定位停止梢straightpin圆柱销stripperbolt脱料螺栓stripperbushing脱模衬套stripperplate剥料板strokeendblock行程止梢submarinegate潜入式浇口supportpillar支撑支柱/顶出支柱supportpin支撑梢supportingplate托板sweeptemplete造模刮板tabgate辅助浇口taperkey推拔键taperpin/锥形梢teeming浇注threestartscrew三条螺纹thrustpin推力销tiebartunnelgate隧道形浇口vent通气孔wortleplate拉丝模板3Dcoordinatemeasurement三次元量床boringmachine搪孔机cncmillingmachineCNC铣床contouringmachine轮廓锯床copygrindingmachine仿形磨床copylathe仿形车床copymillingmachine仿形铣床copyshapingmachine仿形刨床cylindricalgrindingmachine外圆磨床diespottingmachine合模机drillingmachine冲孔机engravingmachine雕刻机engravingE.D.M.雕模放置加工机formgrindingmachine成形磨床graphitemachine石墨加工机horizontalboringmachinehorizontalmachinecenter卧式加工制造中心internalcylindricalmachinejigboringmachine冶具搪孔机jiggrindingmachine冶具磨床lapmachine 研磨机machinecenter加工制造中心multimodelmiller靠磨铣床NCdrillingmachineNC钻床NCgrindingmachineNC磨床NClatheNC车床NCprogrammingsystemNC程式制作系统planer龙门刨床profilegrindingmachine投影磨床projectiongrinder投影磨床radialdrillingmachine旋臂钻床shaper牛头刨床surfacegrinder平面磨床trymachine试模机turretlathe转塔车床universaltoolgrindingmachine万能工具磨床verticalmachinecenter立式加工制造中心wireE.D.M.线割放电加工机alloytoolsteel合金工具钢aluminiumalloy铝合金钢bearingalloy轴承合金blistersteel浸碳钢bonderizedsteelsheet邦德防蚀钢板carbontoolsteel碳素工具钢cladsheet被覆板clodworkdiesteel冷锻模用钢emery金钢砂ferrostaticpressure钢铁水静压力forgingdiesteel 锻造模用钢galvanizedsteelsheet镀锌铁板hardalloysteel超硬合金钢highspeedtoolsteel高速度工具钢hotworkdiesteel热锻模用钢lowalloytoolsteel特殊工具钢lowmanganesecastingsteel低锰铸钢margingsteel马式体高强度热处理钢martrixalloymeehanitecastiron米汉纳铸钢meehanitemetal米汉纳铁merchantironmolybdenumhighspeedsteel钼系高速钢molybdenumsteel钼钢nickelchromiumsteel镍铬钢prehardenedsteel顶硬钢siliconsteelsheet矽钢板stainlesssteel不锈钢tinplatedsteelsheet镀锡铁板toughpitchcoppertroostite吐粒散铁tungstensteel钨钢vinyltappedsteelsheet塑胶覆面钢板agehardening时效硬化ageing老化处理airhardening气体硬化airpatenting空气韧化annealing退火anodeeffect阳极效应anodizingatomloytreatment阿托木洛伊表面austempering奥氏体等温淬火austenite/奥氏体bainite贝氏体bandedstructure条纹状组织barrelplating滚镀barreltumbling滚筒打光blackening 染黑法blueshortness青熟脆性bonderizing磷酸盐皮膜处理boxannealing箱型退火boxcarburizing封箱渗碳brightelectroplating辉面电镀brightheattreatment光辉热处理bypassheattreatment旁路热处理carbide炭化物carburizedcasedepth浸碳硬化深层carburizingcementite炭化铁chemicalplating化学电镀chemicalvapordepositioncoarsening结晶粒粗大化coating涂布被覆coldshortness低温脆性comemtite渗碳体controlledatmosphere大气热处理cornereffect锐角效应creepingdischarge蠕缓放电decarburization脱碳处理decarburizing 脱碳退火depthofhardening硬化深层diffusion扩散diffusionannealing扩散退火electrolytichardening电解淬火embossing压花etching表面蚀刻ferritefirststageannealing第一段退火flamehardening火焰硬化flametreatmentfullannealing完全退火gaseouscyaniding气体氧化法globularcementitegrainsize结晶粒度granolitetreatment磷酸溶液热处理graphitizing石墨退火hardenability硬化性hardenabilitycurve硬化性曲线hardening硬化heattreatment热处理hotbathquenching热浴淬火hotdipping热浸镀inductionhardening高周波硬化ioncarbonitriding 离子渗碳氮化ioncarburizing离子渗碳处理ionplating离子电镀isothermalannealing等温退火liquidhoning液体喷砂法lowtemperatureannealing低温退火malleablizing可锻化退火martempering麻回火处理martensite马氏体/硬化铁炭metallikon金属喷镀法metallizing真空涂膜nitridingnitrocarburizing软氮化normalizing正常化oilquenching油淬化overageing过老化overheating过热pearlite针尖组织phosphating磷酸盐皮膜处理physicalvapordeposition物理蒸镀plasmanitriding离子氮化pre-annealingprecipitation析出precipitationhardening析出硬化pressquenchingprocessannealing制程退火quenchageing淬火老化quenchhardening淬火quenchingcrack淬火裂痕quenchingdistortion淬火变形quenchingstress淬火应力reconditioning 再调质recrystallization再结晶redshortness红热脆性residualstress残留应力retainedaustenite 残留奥rustprevention防蚀saltbathquenching盐浴淬火sandblast喷砂处理seasoning时效处理secondstageannealing第二段退火seculardistortion经年变形segregation偏析selectivehardening部分淬火shotblast喷丸处理shotpeening珠击法singlestagenitriding等温渗氮sintering烧结处理soaking均热处理softening软化退火solutiontreatment固溶化热处理spheroidizing球状化退火stabilizingtreatmentstraighteningannealing矫直退火strainageing应变老化stressrelievingannealing应力消除退火subzerotreatment生冷处理supercooling过冷surfacehardening表面硬化处理temperbrittleness回火脆性tempercolour回火颜色tempering回火temperingcrack回火裂痕texture咬花thermalrefining调质处理thermoechanicaltreatment加工热处理timequenching时间淬火transformation变态tufftrideprocess软氮化处理underannealing 不完全退火vacuumcarbonitriding真空渗碳氮化vacuumcarburizing真空渗碳处理vacuumhardening真空淬火vacuumheattreatment真空热处理vacuumnitriding真空氮化waterquenching水淬火wetout浸润处理activator活化剂bagmoulding气胎施压成形bondingstrength黏合强度breathing排气caulkingcompound填隙料cell气孔coldslug半凝式射出colorant著色剂colormatchingcolormasterbatch色母料compound混合料copolymer共聚合体cull残料废品cure凝固化cryptometer不透明度仪daylight开隙drycycletime空料试车周期时间ductility延性elastomer弹性体extrudedbeadsealing压出粒涂层法feed供料filler充填剂filmblowing薄膜吹制法floatingplaten活动模板foamingagent发泡剂gloss光泽granule颗粒料gunk料斗hotmark热斑hotstamping烫印injectionnozzle射出喷嘴injectionplunger射出柱塞injectionram射出冲柱isomer同分异构物kneader混合机levelingagent匀涂剂lubricant润滑剂matcheddiemethod配合成形法mouldclampingforce锁模力mouldreleaseagent脱模剂nozzle喷嘴orientedfilm取向薄膜parison吹气成形坏料pellet粒料plasticizer可塑剂plunger压料柱塞porosity孔隙率postcure後固化premix预混料purging清除reciprocatingscrew往复螺杆resilience 回弹性resininjection树脂射出法rheology流变学sheet塑胶片shot注射shotcycle射出循环slipagent光滑剂takeoutdevice取料装置tiebar拉杆toggletypemouldclampingsystem肘杆式锁模装置torpedospreader鱼雷形分流板transparencyvoidcontent空洞率acrylic压克力casein酪素celluloseacetate醋酸纤维素CAcelluloseacetatebutyrate醋酸丁酸纤维素CABcompositematerial复合材料cresolresin甲酚树脂CFdiallyphthalatedispersereinforcement 分散性强化复合材料engineeringplastics工程塑胶epoxyresin环氧树脂EPethylcellulose乙基纤维素ethylenevinylacetatecopolymer乙烯-醋酸乙烯EVAethylene-vinlacetatecopolyme醋酸乙烯共聚物EVAfiberreinforcement纤维强化热固性/纤维强化复合材料highdensitypolyethylene高密度聚乙烯HDPEhighimpactpolystyrene高冲击聚苯乙烯HIPShighimpactpolystyrenerigidity高冲击性聚苯乙烯lowdensitypolyethylene低密度聚乙烯LDPEmelamineresin三聚氰胺酚醛树脂MFnitrocellulose硝酸纤维素phenolicresin酚醛树脂plastic塑胶polyacrylicacid聚丙烯酸PAPpolyamide耐龙PApolybutyleneterephthalate聚对苯二甲酸丁酯PBTpolycarbonate聚碳酸酯PCpolyethyleneglycol聚乙二醇PFGpolyethyleneoxidePEOpolyethyleneterephthalate聚乙醇对苯PETPpolymetylmethacrylatePMMApolyoxymethylene聚缩醛POMpolyphenyleneoxide聚硫化亚苯polyphenyleneoxide聚苯醚PPOpolypropylene聚丙烯PPpolystyrene聚苯乙烯PSpolytetrafluoroethylene聚四氟乙烯PTFEpolytetrafluoroethylene聚四氟乙烯polythene聚乙烯PEpolyurethane聚氨基甲酸酯PUpolyvinylacetate聚醋酸乙烯PVACpolyvinylalcohol聚乙烯醇PVApolyvinylbutyral聚乙烯醇缩丁醛PVBpolyvinylchloride聚氯乙烯PVCpolyvinylfuoride聚氟乙烯PVFpolyvinylidenechloride聚偏二氯乙烯PVDCprepolymer预聚物siliconeresin矽树脂thermoplastic热塑性thermosetting热固性thermosettingplastic塑胶unsaturatedpolyester不饱和聚酯树脂aberration色差bite咬入blackinghole涂料孔(铸疵)blackingscab涂料疤blister起泡blooming起霜blowhole破孔blushing泛白bodywrinkle侧壁皱纹breaking-in冒口带肉bubble膜泡burnmark糊斑burr毛边camber翘曲cell气泡centerbuckle表面中部波皱check细裂痕checking龟裂chipping修整表面缺陷clamp-offcollapse塌陷colormottle色斑corrosion腐蚀crack裂痕crazing 碎裂crazing龟裂deformation变形edge切边碎片edgecrack裂边fading退色fillerspeak填充料斑fissure裂纹flangewrinkle凸缘起皱flaw刮伤flowmark流痕galling毛边glazing光滑gloss光泽greasepits污斑grindingdefect磨痕haircrack发裂haze雾度incrustation水锈indentation压痕internalporosity内部气孔mismatchmottle斑点necking缩颈nick割痕rangepeel橘皮状表面缺陷overflowpeeling剥离pit坑pittingcorrosion点状腐蚀platemark模板印痕pock麻点pockmark痘斑resinstreak树脂流纹resinwear树脂脱落riding凹陷sagging松垂saponification皂化scar疤痕scrap 废料scrapjam废料阻塞scratch刮伤/划痕scuffing深冲表面划伤seam裂痕shockline模口挤痕shortshot充填不足shrinkagepool凹孔sinkmark凹痕skininclusion表皮摺叠straightening矫直streak条状痕surfacecheck表面裂痕surfacerougheningsurging波动torsion扭曲warpage翘曲waviness波痕webbing熔塌weldmark焊痕whitening白化wrinkle皱纹adjustablespanner活动扳手anglecutter角铣刀arbourbacking衬垫beltsander带式打磨机buffing抛光chamferingmachinechamferingtool去角刀具chisel扁錾chuck夹具compass两角规concavecutter凹面铣刀convexcutter凸形铣刀crossjoint十字接头cuttingedgeclearance刃口余隙角drillstand钻台edgefile刃用锉刀file锉刀flangejoint凸缘接头grinder砂轮机hammer铁锤handbrace手摇钻hatching剖面线hexagonheadedbolt六角头螺栓hexagonnut六角螺帽indexhead分度头jack千斤顶jig治具kit工具箱lapping研磨metalsaw金工锯noseangle刀角pinchers钳子pliers铗钳plug柱塞头polisher磨光器protabledriller手提钻孔机punch冲头sandpaper砂纸scraper刮刀screwdriver螺丝起子scribing划线secondoutfile中纹锉spanner扳手splinebroach方栓槽拉刀square直角尺squaresleeker方形镘刀squaretrowelstripping剥离工具T-slotT形槽toolforlathe车刀toolpointangletoolpost刀架tosecan划线盘trimming去毛边waffledieflatteningwiper脱模钳wrench螺旋扳手barreling滚光加工belling压凸加工bending弯曲加工blanking下料加工bulging撑压加工burringcamdiebending凸轮弯曲加工coining压印加工compressing压缩加工compressionbending押弯曲加工crowning凸面加工curlbending卷边弯曲加工curling卷曲加工cutting切削加工dinking切断蕊骨doubleshearing叠板裁断drawing引伸加工drawingwithironing抽引光滑加工embossing浮花压制加工extrusion挤制加工filing锉削加工fineblanking精密下料加工finishblankingfinishing精整加工flanging凸缘加工folding折边弯曲加工folding摺叠加工forming成形加工impactextrusion冲击挤压加工indenting压痕加工ironing引缩加工knurling滚花lockseaming固定接合louvering百叶窗板加工marking刻印加工necking颈缩加工notching冲口加工parting分断加工piercing冲孔加工progressivebending连续弯曲加工progressiveblanking连续下料加工progressivedrawing连续引伸加工progressiveforming连续成形加工reaming铰孔加工restrikingriveting铆接加工rollbending滚筒弯曲加工rollfinishing滚压加工rolling压延加工roughing粗加工scraplessmachining无废料加工seamingshaving缺口修整加工shearing切断加工sizing精压加工/矫正加工slittingspinning卷边?接stamping锻压加工swaging挤锻压加工trimming整缘加工upsetting锻粗加工wiring抽线加工backshaft支撑轴blankdetermination胚料展开bottomslidepress下传动式压力机boarddrophammer板落锤brake 煞车buckle剥砂面camlachiecramp铸包chamottesand烧磨砂charginghopper加料漏斗clearance间隙closed-dieforging合模锻造clumpclutch离合器clutchbrake离合器制动器clutchboss离合器轮壳clutchlining离合器覆盖coilcar带卷升降运输机coilcradle卷材进料装置coilreelstandcolumn圆柱connectionscrew连杆调节螺钉corecompound砂心黏结剂counterblowhammer对击锻锤cradle送料架crank曲柄轴crankless无曲柄式crosscrank横向曲轴cushion缓冲depression外缩凹孔dialfeed分度送料dieapproach模口角度dieassembly合模diecushion模具缓冲垫dieheightdielife模具寿命dieopening母模逃孔diespottingpress调整冲模用压力机doublecrankpress双曲柄轴冲床draghtangle逃料倾斜角edging边锻伸embeddedcore 加装砂心feedlength送料长度feedlevel送料高度fillingcore埋入砂心fillingin填砂filmplay液面花纹fineblankingpress精密下料冲床forgingroll辊锻机finishingslag炼後熔渣flywheel飞轮flywheelbrake飞轮制动器footpress脚踏冲床formboard进模口板frame床身机架friction摩擦frictionbrake摩擦煞车gapshear凹口剪床gear齿轮gib滑块引导部grippergripperfeed夹持进料gripperfeeder夹紧传送装置hammer槌机handpresshandrackpinionpress手动齿轮齿条式冲床handscrewpress手动螺旋式冲床hopperfeed料斗送料idlestage空站inching微调尺寸isothermalforgingkeyclutch键槽离合器knockout脱模装置knucklemechanic转向机构landloader 供料器unloader卸料机loopcontroller闭回路控制器lowerdie下模microinchingdevice微寸动装置microinchingequipment微动装置movingbolster活动工作台notchingpress冲缺口压力机opening 排料逃孔overloadprotectiondevice防超载装置pinchroll导正滚轮pinion小齿轮pitch节距pressfit 压入progressive连续送料pusherfeed推杆式送料pusherfeeder料片押片装置quickdiechangesystem快速换模系统regrinding再次研磨releasing松释动作reversedblanking反转下料robot机器人rollformingmachine辊轧成形rollformingmachine辊轧成形机rollrelease脱辊rollerfeed辊式送料rollerleveler辊式矫直机rotarybender卷弯成形机safetyguard安全保护装置scrapcutter废料切刀scrappress废料冲床seamlessforging无缝锻造shave崩砂shearangle剪角sheetloader薄板装料机shot单行程工作shrinkagefit收缩配合shutheight闭合高度sievemesh筛孔sinteringofsand铸砂烧贴slidebalancer滑动平衡器slughole逃料孔spinformingmachine旋压成形机spotting合模stackfeeder堆叠拨送料机stickness黏模性straightsideframe冲床侧板stretcherleveler拉伸矫直机stripfeeder料材送料装置strippingpressure弹出压力stroke冲程takeoutdevice取料装置togglepress肘杆式压力机transferfeed连续自动送料装置turrentpunchpress转塔冲床twospeedclutch双速离合器uncoiler闭卷送料机unloader卸载机vibrationfeeder振动送料机wiringpress嵌线卷边机abnormalglow不规则辉光放电arcdischarge电弧放电belt皮带centreless无心chromebronze铭铜clearanceangle後角cornersheardrop直角压陷deflection桡曲度dischargeenergy放电能量dressing修整dwell保压flange凸缘gap间隙graphite石墨graphitecontractionallowance电极缩小余量graphiteholder电极夹座haircrack发裂horn电极臂jump跳刀magneticbase磁性座mastergraphite标准电极pipegraphite管状电极pulseribworking肋部加工rollerelectrode滚轮式电极rotarysurface旋转面shank柄部sharpedge锐角部toughbronze韧铜traverse摇臂tungstenbronze钨青铜waviness波形起伏workingallowance加工余量workingdischard锻铸造关连用语accretion炉瘤acidconverter酸性转炉acidliningcupola酸性熔铁炉acidopen-hearthfurnace酸性平炉aerator松砂机airsetmoldairlessblastingcleaning离心喷光allcoremolding集合式铸模allrounddieholder通用模座assemblymark铸造合模记号backpouring补浇注backingsand背砂basebullion粗金属锭basepermeability原砂透气度belling压凸billet坏料bleed漏铸blocker预锻模膛blocking粗胚锻件blowhole铸件气孔boarddrophammer板落锤bottompourmold底浇bottompouring底注boxlessmold脱箱砂模break-offcore缩颈砂心brickmolding砌箱造模法bucklecamber错箱camlachiecramp铸包castblade铸造叶片castingflangecastingonflat水平铸造chamottesand烧磨砂charginghopper加料漏斗cleaningofcasting铸件清理closed-dieforging合模锻造corecompound砂心黏结剂coretemplate砂心模板corevent砂蕊排气孔cornergate压边浇口counterblowhammer对击锻造counterlock止口镶嵌方式depression外缩凹孔dieapproach模口角度drawout锻造拔长drawplate起模板drawspike起模长针dummying预锻embeddedcore加装砂心erosion冲砂fettling铸件清理fillingcore埋入砂心fillingin填砂filmplay液面花纹finishingslag炼後熔渣flashgutterflaskmolding砂箱造模forgingroll辊锻机formboard进模口板gutterhammerman锻工headingmachine顶镦机impacter卧式锻造机inblockcast整体铸造ingot铸锭ingotblank铸坯inlaycasting镶铸法investmentcasting失模铸造isothermalforging恒温锻造loosepiece木模活块moldingpitpouringprocess浇注法recasting重铸rollforging轧锻rolledsurface 轧制表面roughsand粗砂roughingforge粗锻sandcrushing塌箱seamlessforging无缝锻造separate分离shave崩砂shrinkagefit收缩配合shutheight闭合高度sievemesh筛孔sinteringofsand铸砂烧贴slag熔渣slaginclusion夹渣stickness黏模性striplayout带状胚料排样法tapcastingtopgate顶注浇口unworkedcasting不加工铸件upender翻转装置upending顶锻uphillcasting底铸whitecastiron白口铸件barrel滚筒(加工)bending波纹加工broaching拉刀切削centering定中心cutting切削cylindricallathecutting外圆车削electricdischargemachine放电加工electrolyticgrinding电解研磨embossing压花加工facing面车削filing锉刀修润handfinishing手工修润hemming卷边加工hobbing滚齿加工joggling摇动加工lapping抛光/研磨修润laserbeammachining雷射加工lathecutting车床车削planning刨削加工polishing抛亮光reaming铰孔修润roughmachining粗切削rounding圆形加工sawing锯削scaling清除钢碇缺陷shaping成形加工skivingslotting切缝切削taperturning锥度车削threadcutting螺纹切削ultrasonicmachining超音波加工upcutmilling逆铣加工abrasive砂轮Al2O3borazon氧化硼立方晶buffingwheel抛光布轮diamond钻石dresser砂轮整修机dressing修整endlessgrindingbelt循环式研磨带finishingallowance加工余量grain磨粒grindingdisc研磨盘jampup孔眼堵塞mesh网筛目resinoidgrindingwheel半树脂型砂轮slitting切缝量vitrified陶瓷的assemblydrawing装配图autotoolchangecycle自动换刀时间周期beam横梁bendingmoment弯矩bendingstress弯曲应力bottoming底靠buckling纵弯曲chamfering去角斜切channel凹槽chattering颤动checkpoint查核点chip切屑chipconveyor排屑输送机coefficientoffriction摩擦系数compact小型的coolingpipe冷却管coupon试样胚deflection挠曲量distortion扭曲变形drafttaper拔模锥度drawout拉拔fittolerance配合公差flexiblerigidity弯曲刚性gasvent气孔hatching剖面线heatercooler加热器冷却装置hookcavity钩穴inching寸动lug凸缘maintenance维修保固metallurgynotcheffect切口效果outofroughness真圆度performance动作性能pitplanestrain倒角应力plugmill蕊棒轧管机repeatedload重覆载荷rivetedjoint铆钉接合sandpaper砂纸shift偏移shrinkfit热压配合shrinkageholesinking凹陷sketch草图spalling剥落straightness直度submarine深陷式surfaceroughness表面粗度tapping攻螺丝thermocoupletorsionload扭转载荷toughness韧性tracing描图undercut凹割3Dcoordinatemeasurement三次元量床3Dmodeling三次元模拟aberration色差abnormalglow不规则辉光放电abrasive砂轮access通路accretion炉瘤accuratediecasting精密压铸acidconverter酸性转炉acidliningcupolaacidopen-hearthfurnance 酸性平炉activator活化剂acetylene乙炔adjustablespanner活动扳手aerator松砂机agehardening时效硬化ageingairhardening气体硬化airlessplastingcleaning离心喷光airpatentingairpermeabilitytest透气性试验airsetmold常温自硬铸模airventvalveallcoremolding 集合式铸模alloytoolsteel合金工具钢allrounddieholder通用模型aluminiumalloy铝合金钢ampere 电流安培梢anglecutter角铣刀anglewelding角焊angularpin角梢angularpin倾斜梢anodeeffectannealing退火anchorpin锚Pipingwork:铺管工程Steamtrace:加热蒸汽管道Cutting:切割socketweld承插焊接filletweld角焊,填角焊branchconnection分支接续fabricationtolerance.制造容差localheattreatment局部热处理threadedpipe螺纹管sealwelding.密封焊接flangejoint凸缘接头undercut底切feeder馈电线conduitoutlet电线引出口sealfitting密封接头,密封配件Screwthreadlubricant螺纹润滑剂Seal:绝缘层weldreinforcement焊缝补强lockwasher锁紧[止动,防松]垫圈electricalpanel.配电板,配电盘nipple螺纹接头zincplated.镀锌的ringjoint环接,围缘接合bolt螺栓control:控制器NationalElectricalCode全国电气规程masterschedule主要图表,综合图表,设计任务书,主要作业表torquewrench转矩扳手jobsite施工现场flangeconnection.凸缘联接Hardhat：安全帽Goggles：护目镜stockpile贮存packinglist装箱单crate:柳条箱purchasedmateriallist原材料进货单back-feed反馈wirecoil线盘，线卷，NPTthread.美国标准锥管螺纹cableglandterminalblock线弧,接头排接线盒,接线板,线夹powerdrill机械钻connector.insulatedsleeve绝缘套管wireconnector接线器wireterminal电线接头controlwiring控制线路motorlead电动机引出线powerwiring电力布线tenderdocument．提供证件orificeplate.挡板nut螺母flangegasket法兰垫片dimensionalinspection尺寸检验burnthrough烧蚀pipingsystem.管道系统reinforcementofweld加强焊缝fabrication.制造dyepenetrantexamination染料渗透试验法magneticparticleexamination磁粉检验girthweld环形焊缝cementlinedpiping水泥衬里weldjoint焊缝,焊接接头spooldrawing管路图,管路详图spottest 抽查,当场测试buttweldRandomRadiography随机射线照相检查radiographicexamination射线照相检查assembly.装配erection架设examination试验cabletray.电缆盘rigidsteelconduit钢制电线管powercontrol功率控制arcwelding电弧焊controlcable控制电缆操纵索normalbend[法线]弯管cableglands:电缆衬垫exfoliation剥落powerreceptacle电力插座groundingconductor接地导体lightingfixture照明器材junctionbox分线箱raceway电缆管道terminalbox接线盒distributionboard配电盘,配电屏receptacle插座tumbleswitch.翻转开关,拨动式开关cathodicprotectionsystem阴极保护系统Circuitbreaker断路开关amplifierpanel放大器盘controlconsole控制台electricalmaterial电气材料conveniencereceptacle.电源插座cablegland电缆衬垫TIG：Tungsten-arcInert-Gaswelding钨极电弧惰性气体保护焊fillerrod焊条tensilestrength抗张强度shieldgas保护气体shieldjig保护夹具highfrequencygenerator.高频发电机weldingrod焊条fillermetal焊料,焊丝shopfabricationfieldinstallation现场安装weldingbead焊道bothsideswelding.双面焊接residualstress残余应力electrode电焊条condensation冷凝longitudinal.纵向的horizontalline水平线circumferentialjoint周圈接缝nondestructiveexamination.非破坏性检验,qualification:合格性constructionwork施工工程weldedjoint焊接缝焊接节点gascutting.气割arccutting电弧切割grindoff磨掉metallicluster金属光泽ScrewedPipingJoints螺丝状的管接头gouging.刨削槽Bending:挠曲witnesstest订货人在场的试验Welding:焊接Threading:车缧纹Leveling：校平coloridentification彩色识别Alignment：对准,定位调整checkagainst检查,核对Fixing：固定Console：控制台cubicle室,箱audit审计materialcertificate.材料合格证verticalpanel竖直面板powerdistributionpanel配电盘gaugeboard 仪表板beveling,磨斜边localpanel现场配电盘grouting灌浆fabrication加工,制造instrumentrack 计测器支架tankgauge液面计flushing冲洗，填缝analyzer分析器piping管道敷设tubing敷设管道cablefitting电缆配件elbow.弯管接头mainpipebend.弯管弯头solvent溶剂postweldheattreatment焊后热处理jig.夹具arcgouging电弧刨削chipping修琢machining机械加工bridges.管式桥clamp.夹钳tackwelding点焊buttwelding对接焊grinder.磨床commencement.开始gussetplate角撑板,加固板processpipe工艺管道land纹间表面tee三通管丁字钢T形梁opening开口reinforcingpad.补强垫,增强衬板flux焊剂wetdeveloper湿显像剂blowhole气泡,气孔inclusion 杂质imperfection缺陷limitation限度valve阀,闸门structuralattachment结构附件taperedallowance削尖余量tackwelding平头焊接sputter喷溅scale废料lateraltranslation侧向平移weldjoint焊缝,焊接接头plug.塞fusion熔融basematerial基底材料leadfoil铅箔intensifyingscreen增光屏,光增强屏pressuretest.压力试验filmdensity.影片密度linenumber行数leaktest漏泄试验platethickness筛板厚度restoration修理fieldfabricated工地制造的,现场装配的junctionbox.接线盒flowsheet流程图vent放气孔,通风孔drain排水管instrumentair仪表气源blind 挡板pipearrangement管配置civilengineer.土木工程师busduct母线槽substation分站flowinstrument流量计powerdistributionpanellevelinstrument位面计,水平仪pressureinstrument 压力仪表/压力计levelswitch(信号)电平开关,gageglass液位玻璃管pilottube指示灯linecheck小检修recalibration.复校,重新校准blindingplate盲板expansionjoint伸缩接头hydrostaticpressuretest 静水压试验pneumaticpressure气压scaffolding脚手架checkvalve止回阀liquidpenetrantexamination液体渗透探伤testpump试验泵witnessedinspections现场检测hanger吊架controlvalve控制阀,fabricationdrawing制造图纸,制作图schedulenumber表示管壁厚度系列的号码hydrostatictest.流体静力学试验,水压试验designpressure设计压力dispositionnotice处罚通知书pipestanchion管支柱bellowtype波纹管式expansionjoint伸缩接头vibrationstopper：减震器subcontractor转包商WPSWorksProcessSpecification典型工艺规程piping.管道系统flange.凸缘,sleeve套筒ferritic.铁素体的identificationmark识别标志stencil.模绘片版,镂花模板stamping.冲压siliconepaint硅树脂油漆weldbead焊缝automatictemperaturerecorderpenetrameter透度计filmviewer底片观察用光源civilworks土建工程，建筑工程lumpsumprice混合价格,统包价格scrapmaterial废料caulkingmetal填隙合金[金属] (材料)applicationdrawing操作图,应用图cablerouting电缆路由选择channelbases沟渠基底verticalpanel竖直面板localpanel现场配电盘powerdistributionpanel配电盘gaugeboard样板,模板规准尺anchorbolt锚定螺栓expansionbolt伸缩栓,扩开螺栓fieldinstrument.携带式仪表instrumentrack,计测器框架tankgauge油箱液位计guidewire尺度[定距]索,准绳nameplate名牌,商标leadpipe铅管take-offvalve输出阀sub-header分联箱airheader集气管pneumaticsignal气动信号steamtrace加热蒸汽管道electricheattracing.电伴随加热cabletrunk电缆管道stopend封端firebarriers防火间隔bondingwire接合线,conduitbox[电]导管分线匣rigidconduitsflexibleconduit 软管conduitentry导管引入装置roadcrossingductbankCappingends顶盖末端cablearmor电缆包皮层Cablesheathsealingcompound电缆膏coaxialcable同轴电缆looptest环路测试sequencetest.联锁顺序试验lintelbeam水平横楣梁flashplate闪熔镀层anchorbolt地脚螺栓expansionbolt伸缩栓,扩开螺栓shimplate垫板pushbuttonstation按钮式控制站logicdiagram逻辑图calculationsheet计算书flowinstrument流量计levelinstrument位面计,水平仪layoutdrawingtieband捆扎用带材Heatingboxes切孔cuttingopeningcontrolvalveactuator阀控传动机构airset空气中凝固,常温自硬自然硬化solenoidvalve.螺线管阀,电磁阀calorimeter热量计odometer历程标tachometer转速计chronometer精密计时表unitprice工日合计Man-daytotal/work-daytotal人工费costoflabor材料费materialsexpenses机械的mechanical检查接线connectiontest发电机generator调相机phaseregulator周波cycle减负荷装置load-sheddingequipment断路器柜circuitbreakercabinet单母线singlebusbar互感器transformer每相电流CurrentbyPhase封闭式插接closetypesocketjoint发电机控制面板generatorcontrolpanel分级卸载sortedunloading同步控制synchronizationcontrol调速器speedgovernor信号屏signalscreen继电器relay高压柜highpressurecabinet油浸电力变压器oil-immersedpowertransformer空气断路器aircircuitbreaker控制屏controlpanel直流馈电屏directcurrentfeedcontrolpanel电容器electriccondenser计量盘meteringpanel成套配电箱wholesetofdistributionbox落地式floormodel控制开关Controlswitches铜芯电力电缆Coppercorepowercable控制电缆actuatingcable热缩式电力电缆终端头pyrocondensationpowercableterminal钢结构支架配管steelstructurebrackettubing万用槽钢versatileU-steel电缆托架cablebracket钢制托盘式桥架steelTray-typecablesupportsystemwaterproofsocket防水插座Explosion-proofsocket接地绞线earthingtwistedpair接地母线earthingbus接地极lightningconductor硬质聚氯乙烯管rigidpolyvinylchloridepipe航空集散站airterminal水银灯具MercuryLamp金属卤化物灯metalhalidelamp高压钠灯HighPressureSodiumLamp额定电压RatedVoltage额定功率RatedPower光源LightSource防护等级GradeofProtection高压汞灯HighPressureMercuryLamp 高压钠灯HighPressureSodiumLamp金属卤化物灯MetallicHalideLamp照明电缆lightingcable单线mongline穿线threading接地跨接线earthingjumper分线箱junctionbox接线盒connectionbox圆钢roundsteel扁钢flatsteel插座socket配电盘switchboard转换开关alternationswitch自动指令呼叫装置automaticinstructioncallingdevice扬声器loudspeaker明装UnfoldInstall暗装ConcealInstall感温探测器ThermalDetector恒温·干燥器/恒温恒湿器DryingOvens/HumidityChambers---(在重庆有OEM生产)ForcedConvectionConstantTemperatureOvens惰性气体恒温器InertGasOvens精密恒温器PrecisionConstantTemperatureOvens洁净恒温器CleanOvens送风定温干燥器ForcedConvectionConstantTemperatureDryingOvens空气幕送风定温恒温器ForcedConvectionOvensWithAirCurtain定温干燥箱ConstantTemperatureDryingOvens角形真空定温干燥器VacuumDryingOvens恒温恒湿器ConstantTemperatureandHumidityChambers流水线设备In-LineSystemforUnderfillAdhesiveandEncapsulation恒温培养器ConstantTemperatureIncubators---可程式低温培养器LowTemperatureProgramTypeIncubators低温培养器LowTemperatureIncubators低温稳定性培养器LowTemperatureStabilityIncubators培养器IncubatorsCO2培养器。
模具(机械-压铸)英语词汇表
GLOSSARYAabrasive grinding 强力磨削abrasive[☜'breisiv] a.磨料的, 研磨的absence ['✌bs☜ns] n.. 不在，缺席accesssory[✌k'ses☜ri] n.附件accommodate[☜'k m☜deit] v. 适应accordingly[☜'k :di☠li] adv.因此,从而,相应地accuracy['✌kjur☜si] n精度,准确性actuate['✌ktjueit] vt.开动(机器), 驱动adequate['✌dikwit] a. 足够的adhesive[☜d'hi:siv] n. 粘合剂adjacent[☜'d✞eisnt] a. 邻近的adopt[☜'d pt] vt. 采用advance [☜d'v✌:ns] n.进步advisable [☜d'vaizbl] adj. 可取的agitate['✌d✞iteit] v. 摇动a large extent 很大程度algorithm ['✌l♈☜ri❆☜m] n. 算法align [☜'lain] v 定位，调准alignment[☜'lainm☜nt] n. 校直all-too-frequent 频繁allowance[☜'l☜uens] n. 容差, 余量alternate[' :lt☜nit]v.交替,轮流alternative[ :l't☜:n☜tiv] n. 替换物alternatively[ :l't☜:n☜tivli] ad. 做为选择, 也许aluminiun[ ✌lju'minj☜m] n.铝ample['✌mpl] adj. 充足的analysis [☜'n✌l☜sis] n. 分析ancillary['✌nsil☜ri] a.补助的, 副的angular ['✌♈jul☜] adj. 有角的annealing[☜'li:li☠] n.退火aperture ['✌p☜t☞☜] n.孔applied loads 作用力appropriate [☜'pr☜uprieit] a. 适当的arc[a:k] n.弧, 弓形arise[☜'raiz] vi. 出现, 发生arrange[☜'reid✞] v. 安排article['a:tikl] n.制品, 产品ascertain[ ✌s☜'tein] vt. 确定, 查明assemble[☜'sembl] vt.组装attitude ['✌titju:d] n 态度auxiliary [ :♈'zilj☜ri]adj. 辅助的avoid[☜'v id] v.避免axis['✌ksis] n.轴axle['✌ksl] n.轮轴, 车轴Bbackup['b✌k ✈p] n. 备份batch [b✌t☞] n 一批bearing['b☪☜ri☠] n.轴承,支座bed[bed] n. 床身behavior[bi'heivj☜] n. 性能bench-work 钳工工作bend[bend] v.弯曲beneath[bi'ni: ] prep在···下bin [bin] n. 仓，料架blank [bl✌☠k] n. 坯料blank [bl✌☠k] v. 冲裁,落料blanking tool 落料模blast [bl✈st] n.一阵（风）blemish['blemi☞] n. 缺点, 污点bolster['b☜ulst☜] n. 模座,垫板boost[bu:st] n. 推进boring['b :ri☠] n.镗削, 镗孔bracket ['br✌kit] n. 支架brass [br✌s] n.黄铜break down 破坏breakage ['breikid✞] n.破坏bridge piecebrine[brain] n. 盐水brittle['britl] adv.易碎的buffer [b✈f☜] n.缓冲器built-in 内装的bulging [b✈ld✞i☠] n. 凸肚burr [b☜:] n. 毛刺bush [bu☞] n. 衬套bush[bu☞]n. 衬套by far (修饰比较级, 最高级)···得多, 最by means of 借助于Ccabinet ['k✌binit] n.橱柜call upon 要求carbide['ka:baid] n.碳化物carburzing['ka:bjureti☠] n. 渗碳carriage['k✌rid✞] n.拖板, 大拖板carry along 一起带走carry down over 从···上取下carry out 完成case hardening 表面硬化case[keis] n. 壳, 套cast steel 铸钢casting['ka:sti☠] n. 铸造,铸件category['k✌t☜♈☜uri] n. 种类caution ['k :☞☜n] n. 警告，警示cavity and core plates 凹模和凸模板cavity['k✌viti] n.型腔, 腔, 洞centre-drilling 中心孔ceramic[si'r✌mik] n.陶瓷制品chain doted line 点划线channel['t☞✌nl] n.通道, 信道characteristic[k✌r☜kt☜'ristik] n.特性check[t☞ek] v.核算chip[t☞ip] n.切屑, 铁屑chuck [t☞✈k] n.卡盘chute [☞u:t] n. 斜道circa ['s☜k☜:] adv. 大约circlip['s☜:klip] n.(开口)簧环circuit['s☜:kit] n. 回路, 环路circular supoport block circulate['s☜:kjuleid] v.(使)循环clamp [kl✌mp] vt 夹紧clamp[kl✌mp] n.压板clay[klei] n. 泥土clearance ['kli☜r☜ns] n. 间隙clip [klip] vt. 切断，夹住cold hobbing 冷挤压cold slug well 冷料井collapse[k☜'l✌ps] vi.崩塌, 瓦解collapsible[k☜'l✌ps☜bl] adj.可分解的combination [k mbi'nei☞☜n] n. 组合commence[k☜'mens] v. 开始, 着手commence[k☜'mens]v. 开始commercial [k☜'m☜:☞☜l] adj. 商业的competitive[k☜m'petitiv] a. 竞争的complementary[ k mpli'ment☜ri] a.互补的complexity [kem'pleksiti] n.复杂性complicated['k mpl☜keitid] adj.复杂的complication [k mpli'kei☞☜n] n. 复杂化compression [k☜m'pre☞☜n] n.压缩comprise[k☜m'prais] vt.包含compromise['k mpr☜maiz] n. 妥协, 折衷concern with 关于concise[k☜n'sais] a. 简明的, 简练的confront[k☜n'fr✈nt] vt. 使面临connector[k☜'nekt☜] n. 连接口, 接头consequent['k nsikw☜nt] a. 随之发生的, 必然的console ['k nsoul] n.控制台consume [k☜n'sjum] vt. 消耗, 占用consummate [k☜n's✈meit] vt. 使完善container[k☜n'tein☜] n. 容器contingent[ken'tind✞☜nt] a.可能发生的contour['k☜ntu☜] n.轮廓conventional[k☜n'ven☞☜nl] a. 常规的converge[k☜n'v☜:d✞] v.集中于一点conversant[k n'v☜:s☜nt] a. 熟悉的conversion[k☜n'v☜:☞☜n] n 换算, 转换conveyer[ken'vei☜] n. 运送装置coolant['ku:l☜nt] n. 冷却液coordinate [k☜u' :dnit] vt. (使)协调copy machine 仿形(加工)机床core[k :] n. 型芯, 核心corresponding [ka:ri'sp di☠] n.相应的counteract [kaunt☜'r✌kt] vt. 反作用,抵抗couple with 伴随CPU (central processing unit) 中央处理器crack[kr✌k ] v.（使）破裂，裂纹critical['kritikl] adj.临界的cross-hatching 剖面线cross-section drawn 剖面图CRT (cathoder-ray tube) 阴极射线管crush[kr✈☞]vt.压碎cryogenic[ krai☜'d✞enik ]a.低温学的crystal['kristl] adj.结晶状的cubic['kju:bik] a. 立方的, 立方体的cup [k✈p] vt (使)成杯状, 引伸curable ['kjur☜bl] adj. 可矫正的curvature['k☜:v☜t☞☜] n.弧线curve [k☜:v] vt. 使弯曲cutter bit 刀头, 刀片cyanide['sai☜naid] n.氰化物Ddash [d✌☞] n. 破折号daylight ['deilait] n. 板距decline[di'klain] v.下落,下降,减少,deform[di'f :m] v. (使)变形demonstrate['dem☜streit ] v证明depict[di'pikt ] vt 描述deposite [di'p zit] vt. 放置depression[di'pre☞☜n] n. 凹穴descend [di'sent] v. 下降desirable[di'zair☜bl] a. 合适的detail ['diteil] n.细节，详情deterioration[diti☜ri:☜'rei☞☜n] n. 退化, 恶化determine[di't☜:min] v.决定diagrammmatic[ dai☜gr☜'m✌tik].a.图解的，图表的dictate['dikteit] v. 支配die[dai] n.模具, 冲模, 凹模dielectric[daii'lektrik] n. 电介质die-set 模架digital ['did✞itl ] n.数字式数字, a.数字的dimensional[dddi'men☞☜nl] a. 尺寸的, 空间的discharge[dis't☞a:d✞] n.v. 放电, 卸下, 排出discharge[dis't☞a:d✞] v.卸下discrete [dis'cri:t] adj. 离散的,分立的dislodge[dis'l d✞] v. 拉出, 取出 L12 dissolution[dis☜'lu:☞☜n] n.结束distinct [dis'ti☠kt] a.不同的，显著的distort [dis'd :t] vt. 扭曲distort[dis't :t] vt. (使)变形, 扭曲distributed system 分布式系统dowel ['dau☜l] n. 销子dramaticlly [dr☜'m✌tikli] adv. 显著地drastic ['dr✌stik] a.激烈的draughting[dra:fti☠] n. 绘图draughtsman['dr✌ftsm☜n] n. 起草人drawing['dr :i☠] n. 制图drill press 钻床drum [dr✈m] n.鼓轮dual ['dju:☜l] adv. 双的，双重的ductility [d✈k'tiliti ] n.延展性dynamic [dai'n✌mik ] adj 动力的Eedge [ed✞] n .边缘e.g.(exempli gratia) [拉] 例如ejector [i'd✞ekt☜] n.排出器，ejector plate 顶出板ejector rob 顶杆elasticity[il✌'stisiti] n.弹性electric dicharge machining 电火花加工electrical discharge machining电火花加工electrochemical machining 电化学加工electrode[i'lektr☜ud] n. 电极electro-deposition 电铸elementary [el☜'ment☜ri] adj.基本的eliminate[i'limineit] vt. 消除, 除去elongate[i'l ☠♈et] vt. (使)伸长, 延长emerge [i'm☜:d✞] vi. 形成, 显现emphasise['emf☜saiz] vt. 强调endeavour[en'dev☜] n. 尽力engagement[in'♈eid✞ment] n. 约束, 接合enhance[in'h✌ns] vt. 提高, 增强ensure [in'☞u☜] vt. 确保，保证envisage[in'vizid✞] vt.设想erase[i'reis] vt. 抹去, 擦掉evaluation[i'v✌lju ei☞☜n] n. 评价, 估价eventually[i'v☜nt☞u☜li ] adv.终于evolution[ev☜'lu:☞☜n] n.进展excecution[eksi'kju:☞☜n] n. 执行, 完成execute ['ekskju:t] v. 执行exerte [i♈'z☜:t] vt. 施加experience[iks'piri☜ns] n. 经验explosive[iks'pl☜usiv]adj.爆炸(性)的extend[eks'tend] v. 伸展external[eks't☜:nl] a. 外部的extract[eks'tr✌kt] v. 拔出extreme[iks'tri:m] n. 极端extremely[iks'tri:mli] adv. 非常地extremity[iks'tmiti] n. 极端extrusion[eks'tru:✞☜n] n. 挤压, 挤出FF (Fahrenheit)['f✌r☜nhait] n.华氏温度fabricate ['f✌brikeit] vt.制作,制造facilitate [f☜'siliteit] vt. 帮助facility[f☜'siliti] n. 设备facing[feisi☠] n. 端面车削fall within 属于, 适合于fan[f✌n] n.风扇far from 毫不, 一点不, 远非fatigue[f☜'ti♈] n.疲劳feasible ['fi:z☜bl] a 可行的feature ['fi:t☞☜] n.特色, 特征feed[fi:d] n.. 进给feedback ['fi:db✌k] n. 反馈female['fi:meil] a. 阴的, 凹形的ferrule['fer☜l] n. 套管file system 文件系统fitter['fit☜] n.装配工, 钳工fix[fiks] vt. 使固定, 安装, vi. 固定fixed half and moving half 定模和动模flat-panel technology 平面(显示)技术flexibility[fleksi'biliti] n. 适应性, 柔性flexible['fleks☜bl] a. 柔韧的flow mark 流动斑点follow-on tool 连续模foregoing ['f :'♈☜ui☠]adj. 在前的,前面的foretell[f :'tell] vt. 预测, 预示, 预言forge[f :d✞] n. v. 锻造forming[f :mi☠] n. 成型four screen quadrants 四屏幕象限fracture['fr✌kt☞☜] n.破裂free from 免于Ggap[♈✌p] n. 裂口, 间隙gearbox['♈i☜b ks] n.齿轮箱general arrangementgovern['♈✈v☜n] v.统治, 支配, 管理grain [♈rein] n. 纹理graphic ['♈r✌fik] adj. 图解的grasp [♈r✌sp] vt. 抓住grid[♈rid] n. 格子, 网格grind[♈raind] v. 磨, 磨削, 研磨grinding ['♈raindi☠] n. 磨光,磨削grinding machine 磨床gripper[♈rip☜] n. 抓爪, 夹具groove[♈ru:v] n. 凹槽guide bush 导套guide pillar 导柱guide pillars and bushes 导柱和导套Hhandset['h✌ndset] n. 电话听筒hardness['ha:dnis] n.硬度hardware ['ha:dw☪☜] n. 硬件headstock['hedst k] n.床头箱, 主轴箱hexagonal[hek's✌♈☜nl] a. 六角形的, 六角的hindrance['hindr☜ns] n.障碍, 障碍物hob[h b] n. 滚刀, 冲头hollow-ware 空心件horizontal[h ri'z ntl] a. 水平的hose[h☜uz] n. 软管, 水管hyperbolic [haip☜'b lik] adj.双曲线的Ii.e. (id est) [拉] 也就是identical[ai'dentikl] a同样的identify [ai'dentifai] v. 确定, 识别idle ['aidl] adj.空闲的immediately[i'mi:dj☜tli] adv. 正好, 恰好impact['imp✌kt] n.冲击impart [im'pa:t] v.给予implement ['implim☜nt] vt 实现impossibility[imp s☜'biliti] n.不可能impression[im'pre☞☜n] n. 型腔in contact with 接触in terms of 依据inasmuch (as)[in☜z'm✈t☞] conj.因为, 由于inch-to-metric conversions 英公制转换inclinable [in'klain☜bl] adj. 可倾斜的inclusion [in'klu☞☜n] n. 内含物inconspicuous[ink☜n'spikju☜s] a. 不显眼的incorporate [in'k :p☜reit] v 合并,混合indentation[ inden'tei☞☜n ] n.压痕indenter[in'dent☜] n. 压头independently[indi'pein☜ntli] a. 独自地, 独立地inevitably[in'evit☜bli] ad. 不可避免地inexpensive[inik'spensiv]adj. 便宜的inherently [in'hi☜r☜ntli] adv.固有的injection mould 注塑模injection[in'd✞ek☞☜n] n. 注射in-line-of-draw 直接脱模insert[in's☜:t] n. 嵌件inserted die 嵌入式凹模inspection[in'spek☞☜n] n.检查,监督installation[inst☜'lei☞☜n] n. 安装integration [inti'♈rei☞☜n] n.集成intelligent[in'telid✞☜nt]a. 智能的intentinonally [in'ten☞☜n☜li] adv 加强地，集中地interface ['int☜feis] n.. 界面internal[in't☜:nl] a. 内部的interpolation [int☜p☜'lei☞☜n] n.插值法investment casting 熔模铸造irregular [i'regjul☜] adj. 不规则的，无规律irrespective of 不论, 不管irrespective[iri'spektiv] a. 不顾的, 不考虑的issue ['isju] vt. 发布，发出Jjoint line 结合线Kkerosene['ker☜si:n] n.煤油keyboard ['ki:b :d ] n. 健盘knock [n k] v 敲，敲打Llance [la:ns] v. 切缝lathe[lei❆] n. 车床latitude ['l✌titju:d] n. 自由lay out 布置limitation[limi'tei☞☜n] n.限度,限制,局限(性)local intelligence局部智能locate [l☜u'keit] vt. 定位logic ['l d✞ik] n. 逻辑longitudinal['l nd✞☜'tju:dinl] a. 纵向的longitudinally['l nd✞☜'tju:dinl] a. 纵向的look upon 视作, 看待lubrication[lju:bri'kei☞☜n ] n.润滑Mmachine shop 车间machine table 工作台machining[m☜'☞i:ni☠] n. 加工made-to-measure 定做maintenance['meintin☜ns] n.维护,维修majority[m☜'d✞a:riti] n.多数make use of 利用male[meil] a. 阳的, 凸形的malfunction['m✌l'f✈☠☞☜n] n. 故障mandrel['m✌dtil] n.心轴manifestation[m✌nif☜s'tei☞☜n] n. 表现, 显示massiveness ['m✌sivnis ] 厚实，大块measure['me✞☜] n. 大小, 度量microcomputer 微型计算机microns['maikr n] n.微米microprocessor 微处理器mild steel 低碳钢milling machine 铣床mineral['min☜r☜l] n.矿物, 矿产minimise['minimaiz] v.把···减到最少, 最小化minute['minit] a.微小的mirror image 镜像mirror['mir☜] n. 镜子MIT (Massachusetts Institute of Technology) 麻省理工学院moderate['m d☜rit]adj. 适度的modification [m difi'kei☞☜n ] n. 修改, 修正modulus['m djul☜s] n.系数mold[m☜uld] n. 模, 铸模, v. 制模, 造型monitor ['m nit☜ ] v. 监控monograph['m n☜♈ra:f] n. 专著more often than not 常常motivation[m☜uti'vei☞☜n] n. 动机mould split line 模具分型线moulding['m☜udi☠] n. 注塑件move away from 抛弃multi-imprssion mould 多型腔模Nnarrow['n✌r☜u] a. 狭窄的NC (numerical control ) 数控nevertheless[ nev☜❆☜'les] conj.,adv.然而,不过nonferrous['n n'fer☜s] adj.不含铁的, 非铁的normally['n :mli]adv.通常地novice['n vis] n. 新手, 初学者nozzle['n zl] n. 喷嘴, 注口numerical [nju'merikl] n. 数字的Oobjectionable [☜b'd✞ek☞☜bl] adj. 有异议的，讨厌的observe[☜b'z☜:v] vt. 观察obviously [' bvi☜sli] adv 明显地off-line 脱机的on-line 联机operational [ p☜'rei☞☜nl] adj.操作的, 运作的opportunity[ p☜'tju:niti] n. 时机, 机会opposing[☜'p☜uzi☠] a.对立的, 对面的opposite[' p☜zit] n. 反面a.对立的,对面的optimization [ ptimai'zei☞☜n] n.最优化orient [' :ri☜nt] vt. 确定方向orthodox [' : ☜d ks] adj. 正统的，正规的overall['☜uv☜r :l] a.全面的,全部的overbend v.过度弯曲overcome[☜uv☜'k✈m] vt.克服, 战胜overlaping['☜uv☜'l✌pi☠] n. 重叠overriding[☜uv☜'raidi☠] a. 主要的, 占优势的Ppack[p✌k] v. 包装package ['p✌kid✞] vt.包装pallet ['p✌lit] n.货盘panel ['p✌nl] n.面板paraffin['p✌r☜fin] n. 石蜡parallel[p✌r☜lel] a.平行的penetration[peni'trei☞☜n ] n.穿透peripheral [p☜'rif☜r☜l] adj 外围的periphery [p☜'rif☜ri] n. 外围permit[p☜'mit] v. 许可, 允许pessure casting 压力铸造pillar['pil☜] n. 柱子, 导柱pin[pin] n. 销, 栓, 钉pin-point gate 针点式浇口piston ['pist☜n] n.活塞plan view 主视图plasma['pl✌zm☜] n. 等离子plastic['pl✌stik] n. 塑料platen['pl✌t☜n] n. 压板plotter[pl t☜] n. 绘图机plunge [pl✈nd✞] v翻孔plunge[pl✈nd✞] v.投入plunger ['pl✈nd✞☜ ] n. 柱塞pocket-size 袖珍portray[p :'trei] v.描绘pot[p t] n.壶pour[p :] vt. 灌, 注practicable['pr✌ktik☜b] a. 行得通的preferable['pref☜r☜bl] a.更好的, 更可取的preliminary [pri'limin☜ri] adj 初步的，预备的press setter 装模工press[pres] n.压,压床,冲床,压力机prevent [pri'vent] v. 妨碍primarily['praim☜rili] adv.主要地procedure[pr☜'si:d✞☜] n.步骤, 方法, 程序productivity.[pr☜ud✈k'tiviti] n. 生产力profile ['pr☜ufail] n.轮廓progressively[pr☜'♈resiv] ad.渐进地project[pr☜'d✞ekt] n.项目project[pr☜'d✞ekt] v. 凸出projection[pr☜'d✞ek☞☜n] n.突出部分proper['pr p☜] a. 本身的property['pr p☜ti] n.特性prototype ['pr☜ut☜taip] n. 原形proximity[pr k'simiti] n.接近prudent['pru:d☜nt] a. 谨慎的punch [p✈nt☞] v. 冲孔punch shapper tool 刨模机punch-cum-blanking die 凹凸模punched tape 穿孔带purchase ['p☜:t☞☜s] vt. 买，购买push back pin 回程杆pyrometer[pai'n mit☜] n. 高温计Qquality['kwaliti] n. 质量quandrant['kw dr☜nt] n. 象限quantity ['kw ntiti] n. 量，数量quench[kwent☞] vt. 淬火Rradial['reidi☜l] adv.放射状的ram [r✌m] n 撞锤.rapid['r✌pid]adj. 迅速的rapidly['r✌pidli]adv. 迅速地raster['r✌st☜] n. 光栅raw [r :] adj. 未加工的raw material 原材料ream [ri:m] v 铰大reaming[ri:mi☠] n. 扩孔, 铰孔recall[ri'k :l] vt. 记起, 想起recede [ri'si:d] v. 收回, 后退recess [ri'ses] n. 凹槽,凹座,凹进处redundancy[ri'd✈nd☜nsi] n. 过多re-entrant 凹入的refer[ri'f☜:] v. 指, 涉及, 谈及reference['ref☜r☜ns] n.参照,参考refresh display 刷新显示register ring 定位环register['red✞st☜] v. 记录, 显示, 记数regrind[ri:'♈aind](reground[ri:'gru:nd]) vt.再磨研relative['rel☜tiv] a. 相当的, 比较的relay ['ri:lei] n. 继电器release[ri'li:s] vt. 释放relegate['rel☜geit] vt. 把··降低到reliability [rilai☜'biliti] n. 可靠性relief valves 安全阀relief[ri'li:f] n.解除relieve[ri'li:v ]vt.减轻, 解除remainder[ri'meind☜] n. 剩余物, 其余部分removal[ri'mu:vl] n. 取出remove[ri'mu:v] v. 切除, 切削reposition [rip☜'zi☞☜n] n.重新安排represent[ repri'zent☜] v 代表,象征reputable['repjut☜bl] a. 有名的, 受尊敬的reservoir['rez☜vwa: ] n.容器, 储存器resident['rezid☜nt] a. 驻存的resist[ri'zist] vt.抵抗resistance[ri'zist☜ns] n.阻力, 抵抗resolution[ rez☜'lu:☞☜n] n. 分辨率respective[ri'spektiv] a.分别的,各自的respond[ris'p nd] v.响应, 作出反应responsibility[risp ns☜'biliti] n.责任restrain[ris'trein]v.抑制restrict [ris'trikt] vt 限制，限定restriction[ris'trik☞☜n] n. 限制retain[ri'tein] vt.保持, 保留retaining plate 顶出固定板reveal [ri'vil] vt.显示，展现reversal [ri'v☜sl] n. 反向right-angled 成直角的rigidity[ri'd✞iditi] n. 刚度rod[r d] n. 杆, 棒rotate['r☜uteit] vt.(使)旋转rough machining 粗加工rough[r✈f] a. 粗略的routine [ru:'ti:n] n. 程序rubber['r✈b☜] n.橡胶runner and gate systems 流道和浇口系统Ssand casting 砂型铸造satisfactorily[ s✌tis'f✌ktrili] adv. 满意地saw[a :] n. 锯子scale[skeil]n. 硬壳score[sk :] v. 刻划scrap[skr✌p] n.废料, 边角料, 切屑screwcutting 切螺纹seal[si:l] vt.密封secondary storagesection cutting plane 剖切面secure[si'kju☜] v.固定secure[si'kju☜] vt.紧固,夹紧,固定segment['se♈m☜nt] v. 分割sensitive['sensitiv]a.敏感的sequence ['si:kw☜ns] n. 次序sequential[si'kwen☞☜l] a.相继的seriously['si☜ri☜sli] adv.严重地servomechanism ['s☜:v☜'mek☜nizm] n.伺服机构Servomechanism Laboratoies 伺服机构实验室servomotor ['s☜:v☜m☜ut☜] n.伺服马达setter ['set☜] n 安装者set-up 机构sever ['sev☜] v 切断severity [si'veriti] n. 严重shaded[☞✌did] adj.阴影的shank [☞✌☠k] n. 柄.shear[☞i☜]n.剪,切shot[☞t] n. 注射shrink[☞ri☠k] vi. 收缩side sectional view 侧视图signal ['si♈nl] n.信号similarity[simi'l✌riti] n.类似simplicity[sim'plisiti] n. 简单single-point cutting tool 单刃刀具situate['sitjueit] vt. 使位于, 使处于slide [slaid] vi. 滑动, 滑落slideway['slaidwei] n. 导轨slot[sl t] n. 槽slug[sl✈♈] n. 嵌条soak[s☜uk] v. 浸, 泡, 均热software ['s ftw☪☜] n. 软件solid['s lid] n.立体, 固体solidify[s☜'lidifai] vt.vi. (使)凝固, (使)固化solution[s☜'lu:☞☜n] n.溶液sophisiticated [s☜'fistikeitid] adj.尖端的,完善的sound[saund] a. 结实的, 坚固的)spark erosion 火花蚀刻spindle['spindl] n. 主轴spline[splain] n.花键split[split] n. 侧向分型, 分型spool[spu:l] n. 线轴springback n.反弹spring-loaded 装弹簧的sprue bush 主流道衬套sprue puller 浇道拉杆square[skw☪☜] v. 使成方形stage [steid✞] n. 阶段standardisation[ st✌nd☜dai'zei☞☜n] n. 标准化startling['sta:tli☠] a. 令人吃惊的steadily['sted☜li ] adv. 稳定地step-by-step 逐步stickiness['stikinis] n.粘性stiffness['stifnis] n. 刚度stock[st k] n.毛坯, 坯料storage tube display 储存管显示storage['st :rid✞] n. 储存器straightforward[streit'f :w☜d]a.直接的strain[strein] n.应变strength[stre☠] n.强度stress[stres] n.压力,应力stress-strain应力--应变stretch[stret☞] v.伸展strike [straik] vt. 冲击stringent['strind✞☜nt ] a.严厉的stripper[strip☜] n. 推板stroke[strouk] n. 冲程, 行程structrural build-up 结构上形成的sub-base 垫板subject['s✈bd✞ikt] vt.使受到submerge[s☜b'm☜:d✞] v.淹没subsequent ['s✈bsikwent] adj. 后来的subsequently ['s✈bsikwentli] adv. 后来, 随后substantial[s☜b'st✌n☞☜l] a. 实质的substitute ['s✈bstitju:t] vt. 代替,.替换subtract[s☜b'tr✌kt] v.减, 减去suitable['su:t☜bl] a. 合适的, 适当的suitably['su:t☜bli] ad.合适地sunk[s✈☠k](sink的过去分词) v. 下沉, 下陷superior[s☜'pi☜ri☜] adj.上好的susceptible[s☜'sept☜bl] adj.易受影响的sweep away 扫过symmetrical[si'metrikl] a. 对称的synchronize ['si☠kr☜naiz] v.同步,同时发生Ttactile['t✌ktail] a. 触觉的, 有触觉的tailstock['teilst k] n.尾架tapered['teip☜d] a. 锥形的tapping['t✌pi☠] n. 攻丝technique[tek'ni:k] n. 技术tempering['temp☜r☠] n.回火tendency['tend☜nsi] n. 趋向, 倾向tensile['tensail] a.拉力的, 可拉伸的拉紧的, 张紧的tension ['ten☞☜n] n.拉紧,张紧terminal ['t☜:m☜nl ] n. 终端机terminology[t☜:mi'n l☜d✞i ] n. 术语, 用辞theoretically [ i:☜'retikli ] adv.理论地thereby['❆☪☜bai] ad. 因此, 从而thermoplastic[' ☜:m☜u'pl✌stik] a. 热塑性的, n. 热塑性塑料thermoset[' ☜:m☜set] n.热固性thoroughly[' ✈r☜uli] adv.十分地, 彻底地thread pitch 螺距thread[ red] n. 螺纹thrown up 推上tilt [tilt] n. 倾斜, 翘起tolerance ['t l☜r☜ns] n..公差tong[t ☠] n. 火钳tonnage['t✈nid✞] n.吨位, 总吨数tool point 刀锋tool room 工具车间toolholder['tu:lh☜uld☜] n.刀夹,工具柄toolmaker ['tu:l'meik☜] n 模具制造者toolpost grinder 工具磨床toolpost['tu:l'p☜ust] n. 刀架torsional ['t :☞☜nl] a扭转的.toughness['t fnis] n. 韧性trace [treis] vt.追踪tracer-controlled milling machine 仿形铣床transverse[tr✌ns'v☜:s] a. 横向的tray [trei] n. 盘，盘子，蝶treatment['tri:tm☜nt] n.处理tremendous[tri'mend☜s] a. 惊人的, 巨大的trend [trend] n.趋势trigger stop 始用挡料销tungsten['t✈☠st☜n] n.钨turning['t☜:ni☠] n.车削twist[twist ] v.扭曲，扭转two-plate mould 双板式注射模Uultimately['✈ltimitli] adv终于.undercut moulding 侧向分型模undercut['✈nd☜k✈t] n. 侧向分型undercut['✈nd☜k✈t] n.底切underfeed['✈nd☜'fi:d] a, 底部进料的undergo[✈nd☜'♈☜u] vt.经受underside['✈nd☜said] n 下面,下侧undue[✈n'dju:] a.不适当的, 过度的uniform['ju:nif :m] a.统一的, 一致的utilize ['ju:tilaiz] v 利用Utopian[ju't☜upi☜n] adj.乌托邦的, 理想化的Vvalve[v✌lv] n.阀vaporize['veip☜raiz] vt.vi. 汽化, (使)蒸发variation [v☪☜ri'ei☞☜n] n. 变化various ['v☪☜ri☜s] a.不同的,各种的vector feedrate computation 向量进刀速率计算vee [vi:] n. v字形velocity[vi'l siti] n.速度versatile['v☜s☜tail] a.多才多艺的,万用的vertical['v☜:tikl] a. 垂直的via [vai☜] prep.经,通过vicinity[v☜'siniti] n.附近viewpoint['vju:p int] n. 观点Wwander['w nd☜] v. 偏离方向warp[w :p] v. 翘曲washer ['w ☞☜] n. 垫圈wear [w☪☜] v.磨损well line 结合线whereupon [hw☪☜r☜'p n] adv. 于是winding ['waindi☠] n. 绕, 卷with respect to 相对于withstand[wi❆'st✌nd] vt.经受,经得起我的词汇库work[w☜:k] n. 工件workstage 工序wrinkle['ri☠kl] n.皱纹vt.使皱Yyield[ji:ld] v. 生产Zzoom[zu:] n. 图象电子放大11。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
压铸机和模具常用语
司筒shot sleeve
鎚头piston
料壶melting pot sleeve
射咀nozzle
流道/浇口runner/gate
直浇道sprue
浇道套sprue bush
鹅颈gooseneck
压射缸injection cylinder
压射冲头injection plunger
钢呤steel piston ring
排气vent
中央熔炉center furnace
熔化金属molten metal
注料口filling port
顶针ejector pin
顶针痕ejector pad
哥林柱/导柱tie bar
前(定)机板/后(动)机板machine platen (moving/fixed)
前(定)模/后(动)模cover die half(stationary half)/ ejector die half (moveable half) 冷却水通道water cooling channel
样板模prototype die
生产模production die
成套模unit die
组合模sectional die
冲模trim die
模胚/模肉standardized main die frame/ replaceable cavity units
行位/柯(型芯)core slides/core
镶件casting insert
模具钢热处理die steel heatment
模具排位图die layout
夹具jig/fixture
模具寿命die life
浇注系统gating/running system
浇注系统设计design of gating system
铸件凝固数值模拟numerical simulation of casting solidification
铸件工艺计算机辅助设计computer-aided design (CAD) of the casting process 浇口杯pouring cup
芯头斜度core taper
直浇道spure
直浇道窝sprue base
横浇道runner
内浇道ingate
冒口riser/feeder head
留型时间/开型时间opening time
抽芯机构core puller
溢流槽overflow
顶针ejector pin
垃圾位/余料biscuit /slug
锁模力locking force
模板尺寸size of die platen
回炉料foundry returns
废金属料scrap
熔/炉渣slag
沉/浮渣sludge/dross
重熔remelting
哥林柱间距/直径space between tie bars/tie bar diameter 开模行位die stroke
最大/最小压模厚度maximum/minimum die height
干燥周期dry cycle
射料力injection force
压射位置shot position
压射行程injection stroke
鎚头直径plunger diameter
坩埚容积melting pot
专用射料压力specific injection pressure
最大压铸面积casting area
射料量casting weight
顶出力ejector force
顶出行程ejector stroke
最大压力clamp force max.
夹具行程clamp stroke
工作压力normal pressure
液压系统工作液体gydraulic fluid 油箱容积oil tank capacity
泵流量/型号pump capacity/type
蓄压器型号accumulator type
氮气压力nitrogen pressure
燃烧装置burning units
煤气炉gas furnace
燃气炉型号burner type
最大输入量Max. input
电流强度current
电压voltage
马达型号/功率motor type/capacity。