UG中英文对照表

顶针 E.P.
有托顶针Stepped E.P.
扁顶针Rectangular E.P.
司筒 E.P.Sleeve
直身导边Straight Leader Pin
有托导边Shoulder Leader Pin
直身杯司Straight Bushing
有托杯司Shoulder Bushing
方定位块Position Block Set
定位锥Taper Pin Set
尼龙塞Parting Lock
中托司套Ejector Lead Bushing 中托导柱Ejector Leader Pin
脱水口螺丝组Puller Bolt Set
限位螺丝Stopper Bolt
限位钉Positioning Pin
管位块Slotter Key
弹簧Spring
螺钉Screw
限位块Distance Spacer
无头螺钉Screw Plug
平头螺钉Socket Head Cap Screw 波子螺丝Ball Plunger
定位螺钉Positioning Screw Plug 胶圈O ring
喉塞Taper Screw Plug
法兰Locating Ring
唧嘴Sprue Bushing
截流塞Cooling Circuit Plug
上固定板Top Clamping Plate
脱料板Runner Stripper Plate 上模板Cavity Plate
推板Stripper Plate
下模板Core Plate
支承板Support Plate
间隔板Spacer Block
顶针板1 Ejector Plate 1
顶针板2 Ejector Plate 2
下固定板Bottom Clamping Plate 回针Return Pin
拉杆Support Pin
拉杆定位介子Support Pin Spacer
齿轮Gear
丝杆Screw
轴承Bearing
油缸Oil Cylinder
气缸Air Cylinder
间隔圈Spacer Ring
垃圾钉Slopper Ring
撑头Support Pillar
行位开关组Detection Switch Set
站脚Distance Spacer
斜顶ANGULAR
斜顶杆angle ejector rod
上模Cavity
上模镶件Cavity Insert
上模镶针Inlay Cavity Pin
潜水镶套Pin Point Gate Bushing 水口扣针Runer Lock Pin
行位Slider
行位开关组Detection Switch Set
行位镶件Slider Insert
斜边Angular Pin
方斜边Angular Cam
铲鸡Locking Block
行位压板Slider Guide Rail
隔热板Insulation Sheet
压板(其他类) Holding Plate
楔块Spacer Wedge
销钉Dowel Pin
下模Core
下模呵Block Core
下模镶件Core Insert
下模镶针Core Pin
撑头Support Pillar
拉板Tension Link
拉板介子Tension Link Retainer
行位垫块Slide Plate
斜边压块Holding Plate For A.P.
斜顶滑座Slide Unit For Loose Core 冷胶套Sprue Lock Bushing
运水镶件Insert For Cooling
等高螺丝Stopper Bolt
入水gate
进入位gate location
水口形式gate type
大水口edge gate
细水口pin-point gate
转水口switching runner/gate
唧嘴口直径sprue diameter
流道runner
热流道hot runner/hot manifold
热嘴冷流道hot sprue/cold runner
唧嘴直流direct sprue gate
圆形流道round/full/half runner
流道电脑分析mold flow analysis
流道平衡runner balance
热嘴hot sprue
热流道板hot manifold
发热管cartridge heater
探针thermocouples
插头connector plug
插座connector socket
密封/封料seal
运水water line/line lpug
喉管tube
塑胶管plastic tube
快速接头jiffy quick connector plug/socker
模具零件mold components
三板模3-plate mold
二板模2-plate mold
边钉/导边leader pin/guide pi
边司/导套bushing/guide bushing
中托司shoulder guide bushing
中托边guide pin
顶针板ejector retainner plate
托板support plate
螺丝screw
管钉dowel pin
开模槽ply bar scot
内模管位core/cavity inter-lock
司筒 E.P.Sleeve
司筒针ejector pin
缩呵movable core,return core core puller 扣机(尼龙拉勾) nylon latch lock
尼龙拉勾parting locks
行位(滑块) slide
镶件insert
压座/斜鸡wedge
耐磨板/油板wedge wear plate
压条plate
定位圈locating ring
琐扣latch
扣鸡parting lock set
推杆push bar
栓打螺丝S.H.S.B
顶板eracuretun
活动臂lever arm
分流锥spure sperader
水口司bush
隔片buffle
弹弓柱spring rod
弹弓die spring
镶针pin
销子dowel pin
波子弹弓ball catch
琐模块lock plate
复位键\提前回杆early return ba
气阀valves
斜导边angle pin
术语terms
承压平面平衡parting surface support balance
模排气parting line venting
回针碰料位return pin and cavity interference
模总高超出啤机规格mold base shut hight
顶针碰运水water line interferes withejector pin
料位出上/下模part from cavith (core) side
模胚原身出料位cavity direct cut on A-plate,core direct cut 不准用镶件Do not use (core/cavity) insert
用铍铜做镶件use beryllium copper insert
初步(正式)模图设计preliinary (final) mold design
反呵reverse core
弹弓压缩量spring compressed length
稳定性好good stability,stable
强度不够insufficient rigidity
均匀冷却even cooling
扣模sticking
热膨胀thero expansion
公差tolorance
铜公(电极) copper electrode。