毕业设计论文-双馈电动机调速控制系统的设计与仿真

学号：

常州大学

毕业设计（论文）

（2012届）

题目

学生

学院专业班级

校内指导教师专业技术职务

校外指导老师专业技术职务

二○一二年六月

双馈电动机调速控制系统的设计与仿真

摘要：目前，风机、水泵是国民经济中应用广泛的生产设备，广泛地应用于电力、水处理、供水、城市供热、冶金矿产、港口机械、石油化工等工业领域，耗电量很大，几乎占工业耗电量的一半。目前，大多数风机、水泵都采用阀门或档板来调节流量以满足负荷变化的要求，或使用低效调速方法，浪费电能严重。

本文在客观分析风机、泵类负载调速技术发展现状的基础上，针对传统串级调速系统功率因数低的问题，结合双馈电动机节能调速的具体实际，对斩波式串级调速系统的设计方案进行了详细讨论，分析并计算了系统各环节的参数及系统的机械特性。设计了双馈电机的斩波式串级调速系统。调速系统采用绝缘栅双极型晶体管（IGBT）作为直流斩波器，并使用了采用转速、电流双闭环控制。系统能通过控制斩波器的占空比来改变电机转子回路的附加电势，从而达到调速的目的。

关键词：双馈电机；串级调速；斩波；MATLAB仿真

Double fed induction motor speed control system design and

simulation

Abstract：At present, fans, pumps are widely used in the national economy of production equipmen and the field of electricity, water treatment, water supply, urban heating, metallurgy, mineral, port machinery, petroleum chemical industry, the power consumption is large, accounting for almost half of the industrial electricity consumption. At present, the majority of fans, pumps use valve or baffle to adjust the flow to meet the requirements of the load changes, or the use of inefficient speed control, but this way has a serious waste of energy.

On the basis of the objective analysis of the status of the fan or pump load speed technology ‘s development. This paper is in case of Conventional cascade speed control system with low power factor, combined with the specific reality of the double-fed motor energy saving speed control，a detailed discussion had been made about the chopping cascade speed control system design and had a analysis and calculation of the mechanical properties of the various links of the system parameters and system.. A double-fed motor chopping cascade speed control system was designed. The speed control system uses insulated gate bipolar transistor ((IGBT) as the DC chopper and the speed and current closed-loop control are used. In the system the speed can be controlled by the way to control the duty cycle of the chopper to change the additional potential of rotor circuit.

Key words：Doubly fed motor; Cascade control; Chopper;MATLAB Simulation

目录

摘

要···············································

··················································

(Ⅰ)

目

次···············································

··················································

(Ⅲ)

1 引

言···············································

··················································

(1)

1.1 双馈电动机的简介和发展状

况·······

··········

··········

··········

··········

··········

··········

··········

··········

··1

1.2 串级调速系统的简介及发其展现

状···············································

(2)

1.3 本课题研究的内容和技术要

求···············································

(2)

2 双馈电动机调速控制系统的设

计···············································

(3)

2.1 串级调速系统的原

理···············································

··················································

(3)