管件常用英语词汇

合集下载

常用管件管道配件中英文对照

常用管件管道配件中英文对照１.管件系列1.1>>P管子Pipe1.2>>EL弯头Elbow1.2.1>ELL长半径弯头Long radius elbow1.2.2>ELS短半径弯头Short radius elbow1.2.3>MEL斜接弯头（虾米腰弯头）Mitre elbow1.2.4>REL异径弯头Reducing elbow1.3>>T三通Tee1.3.1>LT斜三通Lateral tee1.3.2>RT异径三通Reducing tee1.3.3>CROSS四通1.4>>R异径管接头（大小头）Reducer1.4.1>CR同心异径管接头（同心大小头）Concentric reducer 1.4.2>ER偏心异径管接头（偏心大小头）Eccentric reducer 1.5>>CPL管箍Coupling1.5.1>FCPL双头管箍Full coupling1.5.2>HCPL单头管箍Half coupling1.5.3>RCPL异径管箍Reducing coupling1.6>>BU内外螺纹接头Bushing1.7>>UN活接头Union1.8>>HC软管接头Hose coupler1.9>>SE翻边短节Stub end1.10>>NIP短节Pipe nipple or straight nipple1.10.1>SNIP异径短节Swaged nipple1.11>>CP管帽（封头）Cap1.12>>PL管堵（丝堵）Plug1.13>>BLK盲板Blank1.13.1>SB8字盲板Spectacle blind1.14>>PAD补强板Reinforcing pad1.15>焊接支管台WELDOLET1.16>螺纹支管台THREADOLET1.17>FO限流孔板2法兰2.1>>PLG法兰Flange2.1.1>WNF对焊法兰Welding neck flange2.1.2>SOF平焊法兰Slip-on flange2.1.3>SWF承插焊法兰Socket-welding flange2.1.4>T螺纹法兰Threaded flange2.1.5>LJ松套法兰Lapped joint flange2.1.6>REDF异径法兰Reducing flange2.1.7>BF法兰盖（盲法兰）Blind flange2.2>>FSF法兰密封面Flange scaling face2.2.1>FF全平面Flat face2.2.2>RF凸台面Raised face2.2.3>MFF凹凸面Male and female face2.2.4>LF凹面Female face2.2.5>LM凸面Male face2.2.6>RJ环连接面Ring joint face2.2.7>TG榫槽面Tongue and groove face2.2.8>TF榫面Tongue face2.2.9>GF槽面Groove face3垫片3.1>>>G垫片Gasket3.1.1>>NMG非金属垫片Non-metallic gasket3.1.1.1>AG石棉垫片Asbestos gasket3.1.1.2>RG橡胶垫片Rubber gasket3.1.1.3>TEG聚四氟乙烯包复垫片PTFE envelope gasket 3.1.2>>SMG半金属垫片Semimetallic gasket3.1.2.1>MJG金属包垫片Meta-jacket gasket3.1.2.2>SWG缠绕式垫片Spiral wound gasket3.1.3>>MG金属垫片Metallic gasket3.1.3.1>FMG金属平垫片Flat metallic gasket3.1.3.2>SMSG齿形金属垫片Solid metal serrated gasket 3.1.3.3>LER透镜式金属环垫Lens ring gasket3.1.3.4>OCR八角形金属环垫Octagonal ring gasket3.1.3.5>OVR椭圆形金属环垫Oval ring gakset3.1.3.6>IR/OR内外定位环Inner ring and outer ring 3.1.3.7>IR内定位环Inner ring3.1.3.8>OR外定位环Outer ring4坚固件4.1>>B螺栓Bolt4.1.1>SB螺柱Stud bolt4.2>>NU螺母Nut4.3>>TB花蓝螺母Turnbuckle4.4>>WSR垫圈Washer4.4.1>SWSR弹簧垫圈Spring washer5阀门5.1>>GV闸阀Gate valve5.2>>GLV截止阀Globe valve5.3>>CHV止回阀Check valve5.4>>BUV蝶阀Butterfly valve5.5>>BAV球阀Ball valve5.6>>PV旋塞阀Plug valve(cock)5.7>>CV调节阀Control valve5.8>>SV安全阀Safety valve5.9>>RV减压阀Pressure reducing valve 5.10>>ST蒸汽疏水阀Steam trap5.11>>PRV泄压阀Pressur relief valve5.12>>BV呼吸阀Breather valve5.13>>NV针形阀Needle valve5.14>>AV角阀5.15>>DV隔膜阀5.16>>TWV三通阀5.17>>SGV插板阀6管道上用的小型设备6.1>>SPR气液分离器Separator6.2>>FA阻火器Flame arrester6.3>>SR过滤器Strainer6.3.1>SRY Y型过滤器Y-type strainer6.3.2>SRT T型过滤器T-type strainer6.3.3>SRB桶式过滤器Bucket type strainer 6.3.4>TSR临时过滤器Temporary strainer 6.4.>>SIL消声器Silencer6.5>>SG视镜Slight glass6.6>>SC取样冷却器Sample cooler6.7>>DF排液漏斗Drain funnel6.8>>LM管道混合器Line mixer6.9>>RO限流孔板Restriction orifice6.9.1>MO混合孔板Mixing orifice6.1>>>RD爆破片（爆破膜）Rupture disk6.11>>EJ补偿器Expansion joint7隔热、伴热编号缩写中文名称英文名称7.1>>INS隔热Thermal insulation7.1.1>H保温Hot insulation7.1.2>C保冷Cold insulation7.1.3>>P防烫伤隔热Personnel protection insulation7.2>T&I伴热Tracing and insulation7.3>T管道伴热（冷）Tracing7.3.1>EST蒸汽外伴热External steam tracing7.3.2>IST蒸汽内伴热Internal steam tracing7.3.3>SJT蒸汽夹套伴热Steam-jacket tracing7.3.4>ET电伴热Electric tracing8、配管材料和等级8.1>M金属材料Metallic material8.1.1>CS碳钢Carbon steel8.1.2>CAS铸钢Cast steel8.1.3>FS锻钢Forged steel8.1.4>>AS合金钢Alloy steel8.1.5>SS不锈钢Stainless steel8.1.6>AUST SS奥氏体不锈钢Austenitic stainless-steel 8.1.7>>CI铸铁Cast iron8.1.8>MI可锻铸铁Malleable iron8.1.9>DI球墨铸铁Ductile iron8.1.10>AL铝Aluminum8.1.11>BRS黄铜Brass8.1.12>BRZ青铜Bronze8.1.13>CU紫铜Copper8.1.14>LAS低合金钢Low alloy steel8.1.15>FLAS低合金锻钢Forged low alloy steel8.1.16>CLAS低合金铸钢Cast low alloy steel8.2>>THK壁厚Thickness8.2.1>SCH表号Schedule number8.2.2>STD标准Standard8.2.3>>XS加强Extra strong8.2.4>>XXS特强Double extra strong9、装置布置9.1>>CN建北Construction north9.2>>E东East9.3>>W西West9.4>>S南South9.5>>N北North9.6>>H水平Horizontal9.7>>V竖直、铅直、直立Vertical9.8>>GRD地坪Ground9.9>>UG地下Underground9.10>>BL装置边界线Battery limit line9.11>>ESEW事故沐浴洗眼器Emergency shower and eye washer 9.12>>HS软管站Hose station9.13>>ML接续分界线Match line9.14>>PS管道支架（管架）Piping support9.15>>PR管桥Pipe rack9.16>>STRU构架（构筑物）Structure9.17>>BLDG建筑物Building9.18>>PD清扫设施Purge device9.19>>PT池Pit9.20>>SHLT棚Shelter9.21>>COFF围堰Cofferdam9.22>>FL楼板Floor9.23>>PF平台Plateform10、尺寸标注10.1>>>EL标高Elevation10.2>>BOP管底Bottom of pipe10.3>>COP管中心Center of pipe10.4>>TOP管顶Top of pipe10.5>>FOB底平Flat on bottom10.6>>FOT顶平Flat on top10.7>>CL(屯)中心线Center line10.8>>TL切线Tangent line10.9>>SYM对称的Symmetrical10.10>>BOS支架底Bottom of support10.11>>TOS支架顶Top of support10.12>>CL净距（净空）Clearance10.13>>CTC中心至中心Center to center10.14>>CTF中心至面Center to face10.15>>CTE中心至端部Center to end10.16>>ETE端到端End to end10.17>>FEF法兰端面Flange and face10.18>>FTF面到面Face to face10.19>>D直径Diameter10.20>>DN公称直径Nominal diameter10.21>>ID内径Inside diameter10.22>>OD外径Outside diameter10.23>>DIM尺寸Dimension10.24>>MAX最大Maximum10.25>>MIN最小Minimum10.26>>AVG平均Average10.27>>APP约、近似Approximate10.28>>PT.EL点标高Point elevation11图表11.1>>PFD工艺流程图Process flow diagram11.2>>PID管道和仪表流程图Piping&instrument diagram11.3>>COD接续图Continued on drawing11.4>>DTL详图Datail11.5>>SPDWG管段图Spool drawing(each line isometric drawing) 11.6>>DWGNO图号Drawing number11.7>>DWGI所在图号Drawing identification11.8>>LOW材料表List of material11.9>>MTO汇料Material take-off11.10>>APPX附录Appendix11.11>>JOB.No.工号Job Number11.12>>BEDD基础工程设计数据Basic engineering design data 11.13>>DEDD详细工程设计数据Detail engineering design data 11.14>>REV.No.修改号Recision number11.15>>REF DWG参考图Reference drawing11.16>>SC采样接口Sample connection12、操作方式及工作参数12.1>>AUT自动Automatic12.2>>ML手动Manual control12.3>>CHOP链条操作Chain operated12.4>>CSC铅封关Car seal close12.5>>CSO铅封开Car seal open12.6>>LC锁闭Lock closed12.7>>LO锁开Lock open12.8>>NC正常关Normally close12.9>>NO正常开Normally open12.10>>ATM大气压Atmosphere12.11>>PN公称压力Nominal pressure12.12>>A绝压12.13>>G表压12.14>>(T)温度Temperature12.15>>(P)压力Pressure13、施工13.1>>W焊接Welding13.1.1>AW(SMAW)电弧焊Arc welding13.1.2>GSAW气体保护电弧焊Gas shielded-acr welding13.1.3>EFW电熔焊Elecric fusion welding13.1.4>ERW电阻焊Electric Resistance welding13.1.5>GW气焊Gas welding13.1.6>LW搭接焊Lap welding13.1.7>BW对焊Butt welding13.1.8>TW定位焊Tack welding13.1.9>SW承插焊Socket welding13.1.10>CW连续焊Continuous welding13.1.11>SEW密封焊Seal welding13.1.12>SFG堆焊Surfacing13.1.13>FW现场焊接Field welding13.1.14>TIG(GTAW)钨极惰性气体保护焊(氩弧焊) Gas Tungsten Arc Weld 13.2>>HT热处理Heat treatment13.2.1>>PH预热Preheating13.2.2>SR应力消除Stress relief13.2.3>PWHT焊后热处理Post weld heat treatment13.3>EIT检查、探伤和实验Examination,inspection&testing13.3.1>VE外观检查Visual examination13.3.2>>UI(UT)超声探伤Ultrasonic inspection(test)13.3.3>>RI(RT)射线探伤Radiographic inspection(test)13.3.4>MPI(MT)磁粉探伤Magnetic particle inspection(test)13.3.5>LPI(PT)液体渗透检验Liquid penterant inspection(test)13.3.6>HADT硬度实验Hardness testing13.3.7>HYDT水压实验Hydraulic testing13.3.8>PNET气压实验Pneumatic testing13.3.9>CE焊条Covered electrode13.3.10>WW焊丝Welding wire13.3.11>ASSY装配、组合Assembly13.3.12>F现场Field13.3.13>F/F现场制造Field faricated13.3.14>SF现场决定Suit in field13.3.15>CSP冷紧Cold spring13.3.16>BCT螺栓冷紧Bolt cold tightening13.3.17>BHY螺栓热紧Bolt hot tightening13.3.18>CO清洗口Clean out13.3.19>ANNY退火Annealed13.4>PE平端面Plain end13.5>BE坡口端Belelled end13.6>THR螺纹Thread13.7>HB布氏硬度Brinnel hardness13.8>RC洛氏硬度14、其他14.1>FDN基础Foundation14.2>INF信息（资料）Information14.3>REF参考Reference14.4>REV修改Revision14.5>SEQ序号（顺序）Sequence14.6>W/E设备带来With equipment14.7>W/I仪表带来With instrument14.8>CM色标Colour mark14.9>CA腐蚀裕度Corrosion allowance14.10>UTL公用系统Utility14.11>UC公用工程接头Utility connection14.12>QTY数量Quantity14.13>WT重量Weight14.14>MHR工时Man hour14.15>BC螺栓分布圆Bolt circle14.16>HP高点High point14.17>LP低点Low point14.18>SUC吸入（口）Suction14.19DIS排出（口）Discharge14.20>SO蒸气吹扫（口）Steam out14.21>NPT美国标准锥管螺纹National standard taper pipe thread 14.22>NPS美国标准直管螺纹National standard straight pipe thread 14.23>DR排液Drain14.24>VT放气Vent14.25>RTG（压力）等级Rating14.26>CL等级Class14.27>SMLS无缝Seamless14.28>螺旋缝Spiral seam。

管件词汇带缩写大全

SWG
金属垫片
Metallic gasket
MG
金属平垫片
Flat metallic gasket
FMG
齿形金属垫片
Solid metal serrated gasket
SMSG
透镜式金属环垫
Lens ring gasket
LER
八角形金属环垫
Octagonal ring gasket
OCR
椭圆形金属环垫
LEP
两端平
Both ends plain
BEP
小端带螺纹的
Small end thread
SET
大端带螺纹的
Large end thread
LET
两端带螺纹的
Both ends thread
BET
一端带螺纹
One end thread
OET
穿线管
EMT Conduit
美国标准椎管螺纹
American standard taper pipe thread
PO
聚四氟乙烯
Polytetrafluoroethene
PTFE
乙丙橡胶
Ethylene propylene rubber
EPR
公称直径
Nominal diameter
DN
公称压力
Nominal pressure
PN
压力级、等级、类别
Class
CL
低压
Low pressure
L.P.
中压
Medium pressure
Sample cooler
SC
排液漏斗
Drain funnel
DF
管道混合器

管件词汇

管件词汇：碳钢弯头Carbon Steel Elbow不锈钢弯头Stainless Steel Elbow高压弯头High-Pressure Elbow同心异径管Concentric Reducers偏心异径管Eccentric Reducers高压异径管High-pressure Reducers不锈钢等径三通Stainless Straight Tee碳钢等径三通Carbon Straight Tee不锈钢等径四通Stainless Straight Cross高压三通High-pressure Tee锻制三通Forged Tee异径接头Template管帽Caps法兰flange长径和短径弯头long and short radius elbows同心和偏心异径接头concentric and eccentric reducers 等径和异径三通straight and reducing outlet tees大小头CONCENTRIC REDUCERTee Equal 相等的三通等径三通Straight Tee异径三通Reducing Tee等径四通Straight Cross90°短半径弯头90°SS Elbow (SR)90°长半径弯头90°SS Elbow (LR)高压厚壁弯头Thickness ElbowU型管Return Bend盲法兰Blank Flange弯管Bends翻边stub ends异径接头reducers公称通径nominal diameter外径(mm) outside diameter中心距至端面的距离center to end理论重量(kg/pcs) approx weightdescription 类种Standard标准Design类型Material材质双丝头Nipple短节SWAGE NIPPLE内外螺纹活接头Union螺桩studHalf-Coupling单承口管箍Coupling双承口管箍盲板Blind Flangespectacle blind 带双圈的盲板Ecentric 偏心的等径直通equal coupling异径直通reducing coupling内牙直通female coupling外牙直通straight tube with outside90等径弯头90 equal elbow45等径弯头45 equal elbow外牙弯头male elbow内牙弯头female elbow等径三通equal tee异径三通reducing tee内牙三通female tee外牙三通male tee管帽cap拆除:dismantle结头（管线的）：tie-in插盲板：slip spade盲板：blank接头：fitting加热器：heater金属缠绕垫片（带外环）:SW with outside ring HR:热轧manifold:管汇常用的模具词汇：3D coordinate measurement 三次元量床boring machine 搪孔機cnc milling machine CNC銑床contouring machine 輪廓鋸床copy grinding machine 仿形磨床copy lathe 仿形車床copy milling machine 仿形銑床copy shaping machine 仿形鉋床cylindrical grinding machine 外圓磨床die spotting machine 合模機drilling machine 钻孔機engraving machine 雕刻機engraving E.D.M. 雕模放置加工機form grinding machine 成形磨床graphite machine 石墨加工機horizontal boring machine 臥式搪孔機horizontal machine center 臥式加工製造中心internal cylindrical machine 內圓磨床jig boring machine 冶具搪孔機jig grinding machine 冶具磨床lap machine 研磨機machine center 加工製造中心multi model miller 靠磨銑床NC drilling machine NC鑽床NC grinding machine NC磨床NC lathe NC車床NC programming system NC程式製作系統planer 龍門鉋床profile grinding machine 投影磨床projection grinder 投影磨床wwwradial drilling machine 旋臂钻床shaper 牛頭鉋床surface grinder 平面磨床try machine 試模機turret lathe 轉塔車床universal tool grinding machine 萬能工具磨床vertical machine center 立式加工製造中心wire E.D.M. 線割放MBT = Male Buttress ThreadsFBT = Female Buttress Threads/vnf_unionh.htm。

管道专业常用英文对照

管道专业常用英文对照一、PIPE （管道/管子）二、FITTING （管件/连接件）3、 FTE ——内螺纹 MTE 外螺纹 TOE 一端螺纹 TBE 两端螺纹4、 EQ TEE ——等径三通5、 RED TEE ——异径三通6、 CONC.RED ——同心大小头7、 ECC.RED ——偏心大小头8、 RED.CPLG ——异径管接头9、 H.CPLG ——半管接头 F.CPLG ——管接头10、 HOSE CONNECTOR,FTE/FEMALE HOSE END ——软管接头 11、 NIPPLE TOE （NPT ）——螺纹管段 12、 CAP FTE(NPT)——螺纹管帽三、FLANGE （法兰）1、 BLIND ——盲板2、 RF/FF ——凸面/平面3、 SO/WN/LJ ——带颈平焊/带颈对焊/活套4、 STUB END ——翻边5、 MHRF/MH/MHRN ——需二次加工（详见相应图集）四、V ALES （阀门）1、 GA TE VL ——闸阀2、 GLOBE V ALVE ——截止阀3、 BALL V ALVE ——球阀4、 DIAPHRAGM V ALVE ——隔膜阀5、 PRESS SAFETY V ALVE ——安全阀6、 JACKETED V ALVE ——夹套阀7、 BUTTERFLY V ALVE ——蝶阀8、 JACKETED FLUSH BOTTOM V ALVE ——夹套底部冲洗阀 9、其它详见PID 图例五、GASKETS （垫片）六、BOLTS （螺栓）七、其它：1、 JACKET SPACER （固定板）2、 JACKET BARRIER （隔板）3、 FLOW CIRCULA TOR （导流板）4、 PR GAGE （压力表）5、 TEMP GAGE （TEMP SCAN ELEMENT/TEMP ELEMENT ）测温元件管外径表。

管道设计技术英语词汇(大全)

夹石棉的缠绕金属垫片 spiral-wound metal gasket with asbestos filler
内环 inner ring
外环，外定位环 outer ring
波纹金属垫片 corrugated metaBl gasket
波纹金属包嵌石棉垫片 corrugated metal gasket with asbestos inserted
三通 tee
异径三通 reducing tee
等径三通 straight tee
带侧向口的三通（右向或左向） side outlet tee (right hand or 1eft hand)
异径三通（分支口为异径） reducing tee (reducing on outlet)
异径三通（一个直通口为异径）reducing tee (reducing on one run)
指示器/限位器 indicator/stopper
注油器 grease injector
可更换的阀座环 renewable seat ring
1.6.2 常用阀
(1）闸阀 gate valve
平行双闸板 double disc parallel seat
开口楔形闸板 split wedge
本体阀杆密封 body stem seal
石棉安全密封 asbestos emenen seal
倒密封 back seal
压力密封的阀盖 pressure-tight bonnet
动力操纵器 powered operator
电动操纵器 electric motor operator
气动操纵器 pneumatic operator

管道及配件中英文对照

管道及配件中英文对照化工管道词汇翻译1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子（不按配管标准规格制造的其他用管）tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought—steel pipe锻铁管wrought—iron pipe无缝钢管seamless (SMLS）steel pipe焊接钢管welded steel pipe电阻焊钢管electric—resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion （arc）—welded steel-plate pipe 螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot—rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe；straight pipe1。

2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbow长半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通(右向或左向）side outlet tee (right hand or 1eft hand）异径三通（分支口为异径）reducing tee （reducing on outlet）异径三通（一个直通口为异径）reducing tee （reducing on one run）带支座三通base tee异径三通(一个直通口及分支口为异径）reducing tee （reducing on one run and outlet)异径三通（两个直通口为异径，双头式）reducing tee （reducing on both runs，bull head）45°斜三通45°lateral管道及配件中英文对照245°斜三通(支管为异径）45°lateral (reducing on branch）45°斜三通(一个直通口为异径）45°lateral （reducing on one run)45°斜三通（一个直通口及支管为异径）45°lateral (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通(一个分支口为异径)reducing cross （reducing on one outlet)异径四通(一个直通口及分支口为异径) reducing cross （reducing on one run and outlet）异径四通（两个分支口为异径）reducing cross （reducing on both outlet）异径四通(一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet）异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss（以上带红线的单词已经查过，应该是行业很组合的名词,可以查得到）.管接头coupling，full coupling半管接头half coupling异径管接头reducing coupling活接头union内外螺纹缩接(俗称补芯）bushing管帽cap （C)堵头plug短节nipple异径短节reducing nipple；swage nipple两端无螺纹PBE plain both end一端平口POE plain one end一端螺纹TOE thread one end两端螺纹TBE thread both end1.3 弯管Bend预制弯管fabricated pipe bend跨越弯管（形）cross—over bend偏置弯管（~ 形）offset bend90°弯管quarter bend环形弯管circle bend单侧偏置90°弯管(？形）single offset quarter bendS形弯管“S”bend单侧偏置U形膨胀弯管(| ？形）single offset “U”bendU形弯管“U”bend双偏置U膨胀弯管double offset expansion “U”bend斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness1.4 法兰Flange （FLG）整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip—on flange (SO); slip—on welding flange 承插焊法兰socket welding flange松套法兰lap joint flange （LJF）对焊法兰welding neck flange (WNF）法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar （与stub end相似）平焊环welding—on collar突缘短节stub end，lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力-温度等级pressure—temperature rating法兰密封面,法兰面flange facing突面raised face (RF）凸面male face (MF）凹面female face (FMF）榫面tongue face槽面groove face环连接面ring joint face全平面;满平面flat face；full face (FF）光滑突面smooth raised face （SRF）法兰面加工facing finish粗糙度roughness光滑的smooth齿形serrated均方根root mean square (RMS)算术平均粗糙高度arithmetical average roughness height (AARH）配对法兰companion-flange螺栓圆bolt circle （B.C.)1.5 垫片Gasket （GSKT)垫片的型式type of gasket平垫片flat gasket环形平垫片flat ring gasket平金属垫片flat metal gasket夹棉织物的橡胶elastomer with cotton fabric insertion夹石棉织物的橡胶elastomer with asbestos fabric insertion夹石棉织物及金属丝加强的橡胶elastomer with asbestos fabric insertion and with wire reinforcement无石墨压缩白石棉垫片non graphited compressed white asbestos gasket天然白橡胶垫片natural white rubber gasket压缩石棉垫片compressed asbestos class gasket浸聚四氟乙烯的石棉垫片PTFE impregnated asbestos gasket夹石棉的缠绕金属垫片spiral-wound metal gasket with asbestos filler内环inner ring外环,外定位环outer ring波纹金属垫片corrugated metal gasket波纹金属包嵌石棉垫片corrugated metal gasket with asbestos inserted双夹套波纹金属包石棉垫片corrugated metal double jacketed asbestos filled gasket双夹套垫片double jacketed gasket金属包石棉平垫片flat metal jacketed asbestos filled gasket整体金属齿形垫片solid metal serrated gasket槽形金属垫片grooved metal gasket环形连接金属垫片ring joint metal gasket八角环形垫片octagonal ring gasket椭圆环形垫片oval ring gasket透镜式垫片lens gasket非金属垫片non—metallic gasket1.6 阀门Valve1。

管道管件常用英语(全面、实用、难得).

管道管件常用英语1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbowk半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet)异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet)异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull head)45°斜三通45° lateral45°斜三通（支管为异径）45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run)45°斜三通(一个直通口及支管为异径) 45° lateral (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and outlet)异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet) 异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss管接头coupling, full coupling半管接头half coupling异径管接头reducing coupling活接头union内外螺纹缩接（俗称补芯）bushing管帽cap (C)堵头plug短节nipple异径短节reducing nipple; swage nipple预制弯管fabricated pipe bend跨越弯管（^ 形）cross-over bend偏置弯管（~ 形）offset bend90°弯管quarter bend环形弯管cirele bend单侧偏置90°弯管（? 形）single offset quarter bendS形弯管“S” bend单侧偏置U形膨胀弯管（| ?形）single offset “U” bendU形弯管“U” bend双偏置U膨胀弯管double offset expansion “U” bend斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness1.4 法兰Flange (FLG）整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip-on flange (SO); slip-on welding flange 承插焊法兰socket welding flange松套法兰lap joint flange (LJF)对焊法兰welding neckflange (WNF)法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar （与stub end相似）平焊环welding-on collar突缘短节stub end, lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力—温度等级pressure-temperature rating法兰密封面，法兰面flange facing突面raised face (RF)凸面male face (MF)凹面female face (FMF)榫面tongue face环连接面ring joint face全平面；满平面flat face; full face (FF)光滑突面smooth raised face (SRF)法兰面加工facing finish粗糙度roughness光滑的smooth齿形serrated均方根root mean square (RMS)算术平均粗糙高度arithmetical average roughness height (AARH)配对法兰companion-flange螺栓圆bolt circle (B.C.)1.5 垫片Gasket (GSKT)垫片的型式type of gasket平垫片flat gasket环形平垫片flat ring gasket平金属垫片flat metal gasket夹棉织物的橡胶elastomer with cotton fabric insertion夹石棉织物的橡胶elastomer with asbestos fabric insertion夹石棉织物及金属丝加强的橡胶elastomer with asbestos fabric insertion and with wire reinforcement 无石墨压缩白石棉垫片non graphited compressed white asbestos gasket天然白橡胶垫片natural white rubber gasket压缩石棉垫片compressed asbestos class gasket浸聚四氟乙烯的石棉垫片PTFE impregnated asbestos gasket夹石棉的缠绕金属垫片spiral-wound metal gasket with asbestos filler内环inner ring外环，外定位环outer ring波纹金属垫片corrugated metal gasket波纹金属包嵌石棉垫片corrugated metal gasket with asbestos inserted双夹套波纹金属包石棉垫片corrugated metal double jacketed asbestos filled gasket双夹套垫片double jacketed gasket金属包石棉平垫片flat metal jacketed asbestos filled gasket整体金属齿形垫片solid metal serrated gasket槽形金属垫片grooved metal gasket环形连接金属垫片ring joint metal gasket八角环形垫片octagonal ring gasket椭圆环形垫片oval ring gasket透镜式垫片lens gasket非金属垫片non-metallic gasket1.6 阀门Valve1.6.1 阀门结构、零件阀轭yoke外螺纹阀杆及阀轭outside screw and yoke (OS & Y) 阀杆stem内螺纹inside screw (IS)阀轭套yoke sleeve阀杆环stem ring阀座valve seat (body seat)阀座环、密封圈seat ring整体（阀）座integral seat堆焊（阀）座deposited seat阀芯（包括密封圈、杆等内件）trim阀盘disc阀盘密封圈disc seat阀体body阀盖bonnet阀盖衬套bonnet bush螺纹阀帽screw cap螺纹阀盖screw bonnet螺栓连接的阀盖bolted bonnet (BB)活接阀盖（帽）union bonnet (cap)螺栓连接的阀帽bolted cap (BC)焊接阀盖welded bonnet (WB)本体阀杆密封body stem seal石棉安全密封asbestos emenen seal倒密封back seal压力密封的阀盖pressure-tight bonnet动力操纵器powered operator电动操纵器electric motor operator气动操纵器pneumatic operator液压操纵器hydraulic operator快速操纵器quick-acting operator滑动阀杆sliding stem正齿轮传动spur gear operated伞齿轮传动bevel gear operated扳手操作wrench operated链轮chain wheel手轮hand wheel手柄hand lever (handle)气缸（或液压缸）操纵的cylinder operated链条操纵的chain operated等径孔道full bore; full port异径孔道reducing bore, reduced port,venturi port短型short pattern紧凑型（小型）compact type笼式环lantern ring压盖gland阀杆填料stem packing阀盖垫片bonnet gasket升杆式（明杆）rising stem (RS)非升杆式（暗杆）non-rising stem (NRS)指示器/限位器indicator/stopper注油器grease injector可更换的阀座环renewable seat ring1.6.2 常用阀(1）闸阀gate valve平行双闸板double disc parallel seat开口楔形闸板split wedge挠性整体楔形闸扳flexible solid wedge整体楔形闸板solid wedge塞型闸阀plug gate valve直通型闸阀through conduit gate valve(2) 截止阀globe valve球心型阀盘globe type disc塞型阀盘plug type disc可转动的阀盘swivel disc(3) 节流闪阀throttle valve针阀needle valve(4) 角阀angle valve(5) Y型阀（Y 型阀体截止阀）Y-valve (Y-body globe valve)(6) 球阀ball valve三通球阀3-way ball valve装有底轴的trunnion mounted耐火型fire safe type浮动球型floating ball type防脱出阀杆blowout proof stem(7) 蝶阀butterfly valve对夹式（薄片型）wafer type凸耳式lug type偏心阀板蝶阀offset disc burerfly valve; eccentric butterfly valve 斜阀盘蝶阀canted disc butterfly valve连杆式蝶阀link butterfly valve8) 柱塞阀piston type valve(9) 旋塞阀plug valve三通旋塞阀three-way plug valve四通旋塞阀four-way plug valve旋塞cock衬套旋塞sleeve cock(10) 隔膜阀diaphragm valve橡胶衬里隔膜阀rubber lined diaphragm valve直通式隔膜阀straight way diaphragm valve堰式隔膜阀weir diaphragm valve(11) 夹紧式胶管阀pinch valve（用于泥浆、粉尘等）(12) 止回阀check valve升降式止回阀lift check valve旋启式止回阀swing check valve, flap check valve落球式止回阀ball check valve弹簧球式止回阀spring ball check valve双板对夹式止回阀dual plate wafer type check valve无撞击声止回阀non-slam cheek valve底阀foot valve切断式止回阀stop check valve; non-return valve活塞式止回阀piston check valve斜翻盘止回阀tilting disc check valve蝶式止回阀butterfly check valve1.6.3 其它用途的阀安全泄气阀safety valve (SV)安全泄液阀relief valve (RV)安全泄压阀safety relief valve杠杆重锤式lever and weight type引导阀操纵的安全泄气阀pilot operated safety valve复式安全泄气阀twin type safety valve罐底排污阀flush-bottom tank valve电磁阀solenoid valve, solenoid operated valve电动阀electrically operated valve, electric-motor operated valve 气动阀pneumatic operated valve低温用阀cryogenic service valve蒸汽疏水阀steam trap机械式疏水阎mechanical trap浮桶式疏水阀open bucket trap, open top bucket trap浮球式疏水阀float trap倒吊桶式疏水阀inverted bucket trap自由浮球式疏水阀loose float trap恒温式疏水阀thermostatic trap金属膨胀式蒸汽疏水阀metal expansion steam trap液体膨胀式蒸汽疏水阀liquid expansion steam trap双金属膨胀式蒸汽疏水阀bimetallic expansion steam trap压力平衡式恒温疏水阀balanced pressure thermostatic trap热动力式疏水阀thermodynamic trap脉冲式蒸汽疏水阀impulse steam trap放气阀（自动放气阀）air vent valve (automatic air vent valve) （疏水阀用）平板式滑动闸阀slab type sliding gate valve盖阀flat valve换向阀diverting valve, reversing valve热膨胀阀thermo expansion valve自动关闭阀self-closing gate valve自动排液阀self-draining valve管道盲板阀line-blind valve挤压阀squeeze valve（用于泥浆及粉尘等）呼吸阀breather valve风门、挡板damper减压阀pressure reducing valve, reducing valve控制阀control valve膜式控制阀diaphragm operated control valve执行机构actuator背压调节阀back pressure regulating valve差压调节阀differential pressure regulating valve压力比例调节阀pressure ratio regulating valve1.6.4 未指明结构（或阀型）的阀切断阀block valve; shut-off valve; stop valve调节阀regulating valve快开阀quick opening valve快闭阀quick closing valve隔断阀isolating valve三通阀three way valve夹套阔jacketed valve非旋转式阀non-rotary valve排污阀blowdown valve集液排放阀drip valve排液阀drain valve放空阀vent valve卸载阀unloading valve排出阀discharge valve吸入阀suction valve多通路阀multiport valve取样阀sampling valve手动阀hand-operated valve; manually operated valve锻造阀forged valve铸造阀cast valve（水）龙头bibb; bib; faucet抽出液阀（小阀）bleed valve旁路阀by-pass valve软管阀hose valve混合阀mixing valve破真空阀vacuum breaker冲洗阀flush valve第一道阀；根部阀primary valve根部阀root valve总管阀header valve事故切断阀emergency valve1.7 管道特殊件Piping Specialty1.7.1 管道特殊件（组件）粗滤器strainer过滤器filter临时粗滤器（锥型）temporary strainer (cone type)y 型粗滤器y-type strainerT型粗滤器T-type strainer永久过滤器permanent filter丝网粗滤器gauze strainer洗眼器及淋浴器eye washer and shower视镜sight glass阻火器flame arrester喷嘴；喷头spray nozzle取样冷却器sample cooler消声器silencer膨胀节expansion joint波纹膨胀节bellow expansion joint单波single bellow双波double bellow多波multiple bellow压力平衡式膨胀节pressure balanced expansion带铰链膨胀节hinged expansion joint轴向位移型膨胀节axial movement type expansion joint 自均衡膨胀节（外加强环）self-equalizing expansion joint 带接杆膨胀节tied expansion joint万向型膨胀节universal type expansion joint球形补偿器ball type expansion joint填函式补偿器slip type (packed type) expansion joint单向滑动填料函补偿器single actionpacked slip joint1.7.2 管道特殊元件Piping Special Element软管接头hose connection (HC)快速接头quick coupling金属软管metal hose橡胶管rubber hose挠性管flexible tube鞍形补强板reinforcing saddles补强板reinforcement pad特殊法兰special flange漏斗funnel排液环drip ring排液漏斗drain funnel插板blank垫环spacer8字盲板spectacle blind; figure 8 blind限流孔板restriction orifice爆破片rupture disk法兰盖贴面protective disc费托立克接头victaulic coupling1.8 端部连接End Connection法兰端flanged end坡口端beveled end (BE)对焊端butt welded end平端plain end (PE)承插焊端socket welding end螺纹端threaded end (TE)承口bell end焊接端welding end法兰连接（接头）flanged joint对焊连接（接头）butt welded joint螺纹连接，管螺纹连接threaded joint, pipe threaded joint 锥管螺纹密封焊连接seal-welded taper pipe threaded joint 承插焊连接（接头）socket welded joint承插连接（接头）bell and spigot joint环垫接头ring joint (RJ)万向接头universal joint软钎焊连接（接头）soldered joint搭接接头，松套连接lapped joint外侧厚度切斜角bevel for outside thickncss内侧厚度切斜角bevel for inside thickness内外侧厚度切斜角bevel for combined thickness法兰式的flanged (FLGD)对焊的butt welded (BW)螺纹的threaded (THD)承插焊的socket welded (SW)小端为平的small end plain (SEP)大端为平的large end plain (LEP)两端平both ends plain (BEP)小端带螺纹small end thread (SET)大端带螺纹large end thread (LET)两端带螺纹both end thread (BET)一端带螺纹one end thread (OET)支管连接branch connection焊接支管branch pipe welded directly to the run pipe 2 管道用紧固件及螺纹2.1 紧固件螺栓bolt六角头螺栓hexagonal head bolt方头螺栓square head bolt螺柱，双头螺栓stud bolt环头螺检eye bolt沉头螺栓countersunk (head) screw地脚螺栓anchor bolt; foundation bolt松紧螺旋扣（花篮螺丝）turnbuckleU形螺栓U-boltT形螺栓T-bolt圆头螺钉round head bolt机螺栓，机螺钉maehine bolt顶开螺栓，顶起螺栓Jack screw自攻螺钉self tapping screw膨胀螺栓expansion bolt粗制的coarse精制的finished, fine螺母nut六角螺母hexagonal nut方螺母square nut蝶形螺母wing nut扁螺母flat nut锁紧螺母lock nut垫圈washer平垫圈plain washer球面垫圈spherical washer弹簧垫圈spring washer方垫圈square washer斜垫圈slant washer销轴pinned shan销pin开口销cotter pin定位销dowel pin带孔销pin with hole圆锥销taper pin铆钉rivet键key2.2 螺纹左螺纹left hand thread右螺纹right hand thread管螺纹pipe thread锥管螺纹taper pipe thread直管螺纹straight pipe thread梯形螺纹trapezoid thread螺距pitch of thread粗牙螺纹coarse thread细牙螺纹fine thread特细牙螺纹extra fine thread通长螺纹full thread惠氏螺纹whitworth thread公制螺纹metric ibread美国标准锥管螺纹American standard taper pipe thread (NPT) 螺孔tap3 材料、型钢及填料3.1 金属材料3.1.1 黑色金属Ferrous Metal碳素钢carbon steel (CS)低碳钢low-carbon steel中碳钢medium-carbon steel高碳钢high-carbon steel普通碳素钢general carbon steel优质碳素钢high-quality carbon steel普通低合金结构钢general structure low-alloy steel合金结构钢structural alloy steel合金钢alloy steel低合金钢low alloy steel中合金钢medium alloy steel高合金钢high alloy steel耐热钢heat resisting steel高强度钢high strength steel复合钢clad steel工具钢tool steel弹簧钢spring steel钼钢molybdenum steel镍钢nickel steel铬钢chromium steel铬钼钢chrome-molybdenum steel铬镍钢chromium-nickel steel,chrome-nickel steel 不锈钢stainless steel (S.S.)奥氏体不锈钢Austenitic stainless steel马氏体不锈钢Martensitic stainless steel司特来合金（钨铬钴台金）Stellite耐蚀耐热镍基合金Hastelloy铬镍铁合金inconel耐热铬镍铁合金incoloy20合金20 alloy平炉钢（马丁钢）Martin steel镇静钢killed steel半镇静钢semi-killed steel沸腾钢rimmed steel; rimming steel; open-steel锻钢forged steel铸钢cast steel铸铁cast iron (C.I.)灰铸铁grey cast iron可锻铸铁malleable iron (MI)球墨铸铁nodular cast iron; nodular graphite iron 生铁pig iron熟铁，锻铁wrought iron铸件casting高硅铸铁high silicon cast iron3.1.2 镀层及制造方法渗铬钢，镀铬钢chromized steel镀铬的chromium-plated, chrome-plated镀层plating锻造，型钢swage锻造的，锻造forging热轧hot rolling冷轧cold rolling挤压extruding冷加工cold working热加工hot working拔制drawing3.1.3 有色金属Non-ferrous Metal铝aluminum铜，紫铜copper黄铜brass青铜bronze铝青铜aluminum bronze磷青铜phosphor bronze铝镁合金aluminum magnesium锰青铜manganese bronze蒙乃尔（注：镍及铜合金）Monel镍铜台金nickel copper alloy非铁合金nonferrous alloy钛titanium铅lead硬铅hard lead3.1.4 材料性能极限强度ultimate strength抗拉强度tensile strength屈服极限yield limit屈服点yield point延伸率percentage elongation抗压强度compressive strength抗弯强度bending strength弹性极限elastic limit冲击值impact value疲劳极限fatigue limit蠕变极限creep limit持久极限endurance limit布氏硬度Brinell hardness洛氏硬度Rockwell hardness维氏硬度Vickers diamond hardness, diamond penetrator hardness 蠕变断裂强度creep rupture strength断面收缩率reduction of area脆性brittleness延性ductility冷脆cold shortness冷流cold flow3.2 非金属材料Non-metallic Material塑料plastic丙烯腈—丁二烯—苯乙烯acrylonitrile-butadiene-styrene (ABS) 聚乙烯polyethylene (PE)聚氯乙烯polyvinyl chloride (PVC)苯乙烯橡胶styrene-rubber (SR)聚丁烯polybutylene (PB)聚丙烯polypropylene (PP)聚苯乙烯polystyrene (PS)氯化聚醚chlorinated polyether (CPE)聚酰胺polyamide (PA)聚碳酸酯polycarbonate (PC)聚甲基丙烯酸甲酯polymethyl methacrylate (PMMA)醋酸丁酸纤维素cellulose acetate butyrate (CAB)氯化聚氯乙烯chlorinated polyvinyl chloride (CPVC)聚偏二氟乙烯polyvinylidene fluoride (PVDF)缩醛塑料acetal plastic尼龙塑料nylon plastic聚烯烃polyolefin (PO)石墨酚醛塑料graphite phenolic plastics聚四氟乙烯polytetrafluoroethylene (PTFE)纤维增强热塑性塑料fiber reinforced thermoplastics热塑性塑料thermoplastic热固性塑料thermosetting plastics胶粘剂adhesive溶剂胶接剂solvent cement树脂resin环氧树脂epoxy, epoxy resin聚酯树脂polyester resin聚酯纤维polyester fibers氟塑料fluoroplastics聚氨基甲酸酯polyurethane丙烯酸树脂acrylic resin脲醛树脂urea resin呋哺树脂furan resin乙烯丙烯二烃单体ethylene propylene diene monomer (EPDM) 合成橡胶synthetic rubber丁腈橡胶nitrile butadiene rubber氯丁橡胶neoprene天然橡胶natural rubber乙丙橡胶ethylene propylene rubber (EPR)玻璃glass硼硅玻璃borosilicate glass耐火砖fire brick陶瓷ceramic搪瓷porcelain enamel木材wood3.3 型材型钢shaped steel, section steel, swage角钢angle steel槽钢channel工字钢I-beam宽缘工字钢或H钢wide flanged beamT型钢T-bar方钢square bar扁钢flat bar角钢hexagonal steel bar圆钢round steel; rod钢带strap steel钢板plate网纹钢板checkered plate腹板（指型钢的立板）web翼缘（指型钢的缘）wing3.4 填料及填料函填料packing石棉绳asbestos rope, asbestos cord．O形环O-ring自密封self-sealing四氟带Teflon tap带铬镍合金丝的石棉绳asbestos rope with inconel wire, inconel wire asbestos 浸聚四氟乙烯的石棉填料Teflon impregnated asbestos packing金属填料metallic stuffing填料箱，填料函packing box, stuffing box填料函压盖stuffing box gland4 管道等级及材料统计4.1 管道材料规定Piping Material Specification管道等级piping class; piping classification管道等级号class designation公称直径nominal diameter (DN); nominal (pipe) size公称压力nominal pressure (PN)压力级，等级，类别class (CL)低压low pressure (L.P.)中压medium pressure (M.P.)高压high pressure (H.P.)大气压atmosphere (ATM)真空vacuum工作压力operating pressure; working pressure设计压力design pressure工作温度operating temperature设计温度design temperature环境温度ambient temperature腐蚀裕量corrosion allowance管道附件piping attachment管道元件piping element壁厚wall thickness (WT)壁厚系列号schedule number (SCH. No.)加厚的，加强的extra heavy, extra strong双倍加厚的，双倍加强的double extra heavy, double extra strong通用连接组typieal installation分组（类）形式（如管道等级表）block form数据库data base文件file4.2 材料统计Material Take-off (MTO)汇总表summary sheet材料表bill of material (BM)综合管道材料表consolidated piping material summary sheet (CPMSS) 统计材料准确度accuracy of take-off材料情况报告material status report (MSR)散装材料bulk material编位号的itemized代码code number短代码short code数量quantity (QTY)重力weight净重net weight毛重gross weight5 设备布置及管道布置Plot Plan and Piping Layout,Equipment and Piping Arrangement 5.1 设备名称Equipment Name5.1.1 容器Vessel(1) 塔tower, column洗涤塔scrubber吸收塔absorber冷却塔cooling tower精馏塔fractionating tower蒸馏塔distillation tower再生塔regenering tower造粒塔prflling tower汽提塔stripper脱气塔degasifier合成塔synthesis tower(2) 反应器reactor聚台釜polymerizer转化器，变换器converter脱硫反应器desulphurization reactor甲烷化器methanator(3) 气柜gas-holder螺旋式气柜helical gas-holder湿式气柜wet gas-holder干式气柜dry gas-holder(4) 槽罐贮罐tank; storage tank缓冲罐knock out drum球罐spheroid, spherical tank罐drum接受槽receiver计量槽measuring tank加料槽feed tank排污罐blow down tank闪蒸罐flash drum汽包steam drum溶液贮槽solution storage tank地下槽sloptank(5) 其它设备分离器separator旋风分离器cyclone分子筛molecular sieve脱氧器deaerator搅拌器agitator干燥器dryer混合器mixer萃取器extractor结晶器crystallizer澄清器gravity settler净化器purifier气化器vaporizer吸附器adsorber融解槽melter减温器desuperheater升压器booster喷射器ejector喷头sprayer火炬flare消声器silencer(6) 换热器、加热器、冷却器换热器heat exchanger空冷器air cooler水冷却器water cooler冷凝器condenser螺旋板式换热器spiral plate heat exchanger 蒸发器evaporator再沸器reboiler急冷器quencher深冷器chiller预热器preheater再热器reheater加热器heater电加热器electric heater过热器super heater给水加热器feed water heater中间冷却器inter cooler后冷却器after cooler5.1.2 工业炉及锅炉炉子furnace烧嘴burner锅炉boiler烟囱stack废热锅炉waste heat boiler辅助锅炉auxiliary boiler省煤器economizer回热炉direct-fired heater辐射段radiant section对流段convection section裂化炉reformer焚烧炉incinerator回转窑rotary kiln炉管furnace tube吹灰器soot blower观察孔observation door, peep door防爆门explosion door5.2 辅助用房名称5.2.1 生产用房分析室analyzer room变压器室transformer room配电室，变电所substation, switch room蓄电池室battery room控制室control room通风室ventilating room贮藏室storage room维修间maintenance room办公室office5.2.2 生活用房更农室locker room盥洗室，厕所closet, lavatory, toilet5.3 图名管道布置平面piping arrangement plan (PAP)管道布置piping layout轴测图isometric drawing分区索引图key plan初版设备布置图（“A”版）preliminary plot plan ( “A” issue)内部审查版设备布置图（“B”版）inre rnal approval plot plan ( “B” issue)用户审查版设备布置图（“C”版) owner approval plot plan ( “C” issue)确认版设备布置图（“D”版）confirm plot plan ( “D” issue)研究版设备布置图（“e”版）planning plot plan ( “E” issue)设计版设备布置图（“F”）designing plot plan ( “F” issue)施工版设备布置图（“G”版）construct ion plot plan ( “G” issue) 5.4 厂房、站、单元压缩机房compressor house (room)泵房pump house (room)洗眼站eye washer station泡沫站foam station软管站，公用工程站hose station (HS), utility station成套设备package unit设施facilities罐区tank yard空分装置air separation facility5.5 设备布置设备位号equipment item number工厂plant工厂区界plant limit项目区界内侧inside battery limit (I.S.B.L.)项目区界batterylimit (BL)区界area limit区域边界zone iimit界外off site东east (E)西west (W)南south (S)北north (N)上up下down工厂北向plant north真实北向true north道路road小过道cat walk, cat way走道，过道walk way, gangway, access way污水坑（井）sump pit集水池catch basin沟槽through预留区trough场地future area铺砌区paving area非铺砌区unpaved area碎石铺面gravel paving橡皮铺面rubber paving面积，区域area体积，容积volume (VOL)5.6 管道布置管道设计piping design管道研究piping study走向研究routing study重要管道critical piping地上管道above ground piping地下管道under ground piping管网network of pipes管廊pipe rack管沟piping trench管间距line spacing管道跨距line span总管header, manifold旁路by pass排液drain放空vent上升管，垂直管riser导管canduit裸管bare iine管件直接fitting to fitting (FTF)管段，接口spool piece, spool取样接口sampling connection集液包drip leg伴热管tracing pipe蒸汽伴热steam tracing热水伴热hot-water tracing电伴热electrical tracing夹套管jacketed line, jacketed piping 全夹套的full jacketed平面plan详图detail“ ”视图X view “X”“ ”剖视A-A section “A-A”连接图hook up drawing接续图continue on drawing (COD) 接续线match line (M.L.)比例scale图例legend符号symbol管口表list of nozzles方位orientation管口方位nozzle orientation定位location相交intersection水平的horizontal垂直的，立式的vertical垂直，正交，垂直的perpendicular平行，平行的parallel水平安装horizontal installation垂直安装vertical installafion对称的symmetric相反（的），对面（的）opposite顺时针方向clock wise逆时针方向counter clock wise计算机辅助设计computer aided design (CAD) 5.7 图面标注绝对标高abselute elevation海平面标高over-sea mean level (OSL)标高，立面elevation (EL)混凝土顶面top of concrete架顶面top of support (TOS)钢结构顶面top of steel梁项面top of beam (TOB)支撑点point of suppon (POS)管顶top of pipe (TOP)管底bouom of pipe (BOP)沟底boaom of trench管子内底invert (inside bottom of pipe)底平flat on bottom (FOB)顶平flat on top (FOT)工作点working point (W.P.)面至面face to face (F-F)中心至端面center to end (C-E)中心至面center to face (C-F)中心至中心，中至中center to center (C-C)坐标coordinate坐标原点origin of coordinate出口中心线center line of discharge入口中心线center line of suction中心线centerline (CL)入口inlet, suction出口outlet, discharge排出口exhaust距离distance5.8 相关专业的专业词汇5.8.1 工艺(1) 图及表流程图flow diagram工艺流程图process flow diagram (PFD)管道及仪表流程图piping andinstrument flow diagram (PID)公用工程流程图utility flow diagram (UFD) 管线表line list; line schedule命名表；管道表nomenclature设备表equipment list (schedule)(2) 流体fluid空气air仪表空气instrument air工艺空气process air低压蒸汽low pressure steam中压蒸汽medium pressure steam高压蒸汽high pressure steam伴热蒸汽tracing steam饱和蒸汽saturated steam过热蒸汽superheated steam氧气oxygen氢气hydrogen氮气nitrogen燃料气fuel gas天然气natural gas火炬气flare gas酸性气sour gas液化石油气liquefired petroleum gas (LPG) 氨气ammonia gas冷却水cooling循环水circulating water锅炉给水boiler feed water热水hot water蒸汽冷凝水steam condensate盐水brine工艺水process water化学污水chemical sewage防腐剂corrosion inhibitor重油heavy oil石脑油naphtha燃料油fuel oil润滑油lubricating oil密封油sealing oil冷冻剂refrigerant载热体heating medium溶剂solvent溶液solution母液mother liquor单体monomer聚合物polymer均聚物homopolymer共聚物copolymer工艺液体process liquid工艺气体process gas硫酸sulphuric acid盐酸chlorhydric acid硝酸nitric acid烧碱caustic soda(3) 流体特性fluid characteristics 蒸汽压vapor pressure临界温度critical temperature临界点critical point临界压力critical pressure比热specific heat湿度humidity密度density比重specific gravity粘度viscosity闪点flash point融点melting point凝固点freezing point浓度concentration爆炸极限limit of explosion有毒的toxic可燃的；易燃的flammable(4) 其它回收recovery再生regeneration循环cireulatlon再循环；再生recycle补充make-up制备preparation蒸汽吹扫steaming out吹扫purge抽空；排空evacuation吹出blow-off排污blow down破真空vacuum breaker大气腿barometric leg备用stand-by化学清洗chemical cleaning净正吸入压头net positive suction head (NPSH) 进料feed成品product污染contamination大气污染atmospheric pollution环境温度ambient temperature5.8.2 建筑、结构建筑物building钢结构steel structure已有钢结构existing steel structure钢筋混凝土结构reinforced concrete construction 楼面floor平台platform (PF)地面ground level栏杆handrail楼梯stair; stair way直梯ladder柱column; post; stanchion基础foundation; footing粱beam斜撑；支撑bracing桁架；主粱girder构件member隔墙partition wall墙wall篦子板grate; grating吊装孔erection opening吊梁hoisting beam棚shelter窗window天窗skylight门door防火门fire door地漏floor drain防火层fire-proofing总图general plot plan路肩shoulder桩pile灌浆grouting风荷载wind load雪荷载snow load动力荷载dynamic load静荷载dead load活荷载live load风速wind velocity主导风向most frequent wind direction5.8.3 仪表盘（操作盘）panel就地盘local panel仪表盘instrument panel常开normally open常闭normally closed电缆槽（架）cable tray (channel); cable rack 仪表电缆槽（架）instrument cable tray (duct) 压力计manometer; pressure gauge热电偶thermocouple温度计thermometer液位计level gauge玻璃液位计gage glass温度计保护管thermowell流量计flow meter孔板orifice变送器transmitter联锁interlock仪器；设备apparatus仪器分析instrumental analysis自动分析automatic analysis气体分析gas analysis化学分析chemical analysis气相色谱仪gas chromatograph液相色谱仪liquid chromatograph质谱分析mass spectrometric analysis 5.8.4 电气危险区划分hazardous area classification 危险区平面图hazardous area plan电气盘electrical panel配电盘switch board电缆沟cable trench电流current直流direct current交流alternating current频率frequency相位phase功率因数power factor电压voltage电阻resistance电容capacitance静电static electricity接地grounding; easthing照明lighting; illumination避雷针lightning preventer电话telephone电线wire接线箱（盒）junction box导线管conduit tube5.8.5 设备固定鞍座fixed saddle滑动鞍座sliding saddle管口nozzle人孔manhole (MH)手孔handhole (HH)检查孔inspection hole吊柱davit切线tangent line焊接线weldingiine件号part humbet椭圆形封头ellipsoidal head加强圈reinforcing ring接地板earth lug吊耳lifting lug气缸cylinder轴shaft轴承bearing附件，附属设备accessory编位号设备itemized equipment无位号设备non-itemized equipment 5.8.6 水道(1) 流体原水raw water硬水hard water软水soft water饮用水potable water循环冷却水给水cooling water supply 循环冷却水回水cooling water return 脱盐水demineralized water苦咸水（碱性水）brackish water生活污水sanitary sewer工业废水industrial waste water雨水rain water污染雨水contaminated rain water消防水fire water(2) 装置、设施软化装置softener沉淀器settler沉淀池clarifier脱盐装置demineralizer水处理water traatment冷却塔cooling tower中和池neutralization tank化粪池septic tank渗滤井soak-away pit井well阀井valve pit清扫口clean out（3）消防消火栓hydrant水炮water monitor洒水器sprinkler水喷淋watering灭火器fire extinguisher消防水泵fire pump消防车fire fighting truck泡沫消防foam fire-fighting泡沫栓foam hydrant泡沫炮foam monitor消防软管接头fire hose connection6 管道支吊架Pipe Supports and Hangers 6.1 管架零部件Attachment of Support管托shoe管卡clampU形夹（卡）clevis锻制U形夹forged steel clevis支耳；吊耳lug; ear耳轴trunnion止动挡块shear lug托座stool托架cradle带状卡strap clamp夹板，导向板cleat可调夹板adjustable cleat角板；连接板gusset筋；肋rib支承环ring加强板stiffiener底板base plate顶板top plate翅片式导向板fin预埋件embedded part; inserted plate垫板（安装垫平用）shim锚固件；生根件clip预焊件(设备上) clip (on equipment)聚四氟乙烯滑动板PTFE sliding plate连接板tie plate连接杆tie rod限制杆limit rod带环头拉杆eye rod。

常用管件管道配件中英文对照

常用管件管道配件中英文对照１.管件系列1.1>>P 管子Pipe1.2>> EL 弯头Elbow1.2.1> ELL 长半径弯头Long radius elbow1.2.2> ELS 短半径弯头Short radius elbow1.2.3>MEL 斜接弯头（虾米腰弯头）Mitre elbow1.2.4> REL 异径弯头Reducing elbow1.3>> T 三通Tee1.3.1> LT 斜三通Lateral tee1.3.2> RT 异径三通Reducing tee1.3.3> CROSS 四通1.4>>R 异径管接头（大小头）Reducer1.4.1> CR 同心异径管接头（同心大小头）Concentric reducer 1.4.2> ER 偏心异径管接头（偏心大小头）Eccentric reducer 1.5>> CPL 管箍Coupling1.5.1> FCPL 双头管箍Full coupling1.5.2> HCPL 单头管箍Half coupling1.5.3> RCPL 异径管箍Reducing coupling1.6>>BU 内外螺纹接头Bushing1.7>> UN 活接头Union1.8>> HC 软管接头Hose coupler1.9>> SE 翻边短节Stub end1.10>> NIP 短节Pipe nipple or straight nipple1.10.1>SNIP 异径短节Swaged nipple1.11>>CP 管帽（封头）Cap1.12>> PL 管堵（丝堵）Plug1.13>> BLK 盲板Blank1.13.1> SB 8字盲板Spectacle blind1.14>> PAD 补强板Reinforcing pad1.15>焊接支管台 WELDOLET1.16> 螺纹支管台 THREADOLET1.17> FO 限流孔板2 法兰2.1>> PLG 法兰Flange2.1.1> WNF 对焊法兰Welding neck flange2.1.2> SOF 平焊法兰Slip-on flange2.1.3> SWF 承插焊法兰Socket-welding flange2.1.4>T 螺纹法兰Threaded flange2.1.5> LJ 松套法兰Lapped joint flange2.1.6> REDF 异径法兰Reducing flange2.1.7> BF 法兰盖（盲法兰）Blind flange2.2>> FSF 法兰密封面Flange scaling face2.2.1> FF 全平面Flat face2.2.2>RF 凸台面Raised face2.2.3> MFF 凹凸面Male and female face2.2.4>LF 凹面Female face2.2.5> LM 凸面Male face2.2.6> RJ 环连接面Ring joint face2.2.7>TG 榫槽面Tongue and groove face2.2.8> TF 榫面Tongue face2.2.9> GF 槽面Groove face3 垫片3.1>> >G 垫片Gasket3.1.1>> NMG 非金属垫片Non-metallic gasket3.1.1.1> AG 石棉垫片Asbestos gasket3.1.1.2> RG 橡胶垫片Rubber gasket3.1.1.3> TEG 聚四氟乙烯包复垫片PTFE envelope gasket 3.1.2>> SMG 半金属垫片Semimetallic gasket3.1.2.1 >MJG 金属包垫片Meta-jacket gasket3.1.2.2> SWG 缠绕式垫片Spiral wound gasket3.1.3>> MG 金属垫片Metallic gasket3.1.3.1> FMG 金属平垫片Flat metallic gasket3.1.3.2> SMSG 齿形金属垫片Solid metal serrated gasket 3.1.3.3> LER 透镜式金属环垫Lens ring gasket3.1.3.4> OCR 八角形金属环垫Octagonal ring gasket3.1.3.5> OVR 椭圆形金属环垫Oval ring gakset3.1.3.6> IR/OR 内外定位环Inner ring and outer ring 3.1.3.7> IR 内定位环Inner ring3.1.3.8> OR 外定位环Outer ring4 坚固件4.1>> B 螺栓Bolt4.1.1> SB 螺柱Stud bolt4.2>> NU 螺母Nut4.3>> TB 花蓝螺母Turnbuckle4.4>> WSR 垫圈Washer4.4.1 >SWSR 弹簧垫圈Spring washer5 阀门5.1>> GV 闸阀Gate valve5.2>> GLV 截止阀Globe valve5.3>> CHV 止回阀Check valve5.4 >> BUV 蝶阀Butterfly valve5.5>> BAV 球阀Ball valve5.6>> PV 旋塞阀Plug valve (cock)5.7>> CV 调节阀Control valve5.8>> SV 安全阀Safety valve5.9>>RV 减压阀Pressure reducing valve 5.10>> ST 蒸汽疏水阀Steam trap5.11>> PRV 泄压阀Pressur relief valve5.12>> BV 呼吸阀Breather valve5.13>> NV 针形阀Needle valve5.14>> AV 角阀5.15>> DV 隔膜阀5.16>> TWV 三通阀5.17>> SGV 插板阀6 管道上用的小型设备6.1>> SPR 气液分离器Separator6.2 >>FA 阻火器Flame arrester6.3 >>SR 过滤器Strainer6.3.1> SRY Y型过滤器Y-type strainer6.3.2> SRT T型过滤器T-type strainer6.3.3> SRB 桶式过滤器Bucket type strainer 6.3.4> TSR 临时过滤器Temporary strainer 6.4.>> SIL 消声器Silencer6.5 >>SG 视镜Slight glass6.6 >>SC 取样冷却器Sample cooler6.7 >>DF 排液漏斗Drain funnel6.8>> LM 管道混合器Line mixer6.9>> RO 限流孔板Restriction orifice6.9.1> MO 混合孔板Mixing orifice6.1>>> RD 爆破片（爆破膜）Rupture disk6.11 >>EJ 补偿器Expansion joint7 隔热、伴热编号缩写中文名称英文名称7.1 >>INS 隔热Thermal insulation7.1.1> H 保温Hot insulation7.1.2> C 保冷Cold insulation7.1.3>> P 防烫伤隔热Personnel protection insulation7.2 >T&I 伴热Tracing and insulation7.3> T 管道伴热（冷）Tracing7.3.1> EST 蒸汽外伴热External steam tracing7.3.2> IST 蒸汽内伴热Internal steam tracing7.3.3 >SJT 蒸汽夹套伴热Steam-jacket tracing7.3.4 >ET 电伴热Electric tracing8、配管材料和等级8.1> M 金属材料Metallic material8.1.1> CS 碳钢Carbon steel8.1.2 >CAS 铸钢Cast steel8.1.3> FS 锻钢Forged steel8.1.4>> AS 合金钢Alloy steel8.1.5> SS 不锈钢Stainless steel8.1.6> AUST SS 奥氏体不锈钢Austenitic stainless-steel 8.1.7>> CI 铸铁Cast iron8.1.8> MI 可锻铸铁Malleable iron8.1.9> DI 球墨铸铁Ductile iron8.1.10> AL 铝Aluminum8.1.11> BRS 黄铜Brass8.1.12> BRZ 青铜Bronze8.1.13> CU 紫铜Copper8.1.14> LAS 低合金钢Low alloy steel8.1.15> FLAS 低合金锻钢Forged low alloy steel8.1.16> CLAS 低合金铸钢Cast low alloy steel8.2>> THK 壁厚Thickness8.2.1> SCH 表号Schedule number8.2.2> STD 标准Standard8.2.3 >>XS 加强Extra strong8.2.4>> XXS 特强Double extra strong9、装置布置9.1>> CN 建北Construction north9.2 >>E 东East9.3>> W 西West9.4>> S 南South9.5>> N 北North9.6>> H 水平Horizontal9.7>> V 竖直、铅直、直立Vertical9.8>> GRD 地坪Ground9.9>> UG 地下Underground9.10>> BL 装置边界线Battery limit line9.11>> ESEW 事故沐浴洗眼器Emergency shower and eye washer 9.12>> HS 软管站Hose station9.13 >>ML 接续分界线Match line9.14>> PS 管道支架（管架）Piping support9.15>> PR 管桥Pipe rack9.16>>STRU 构架（构筑物）Structure9.17>>BLDG 建筑物Building9.18>> PD 清扫设施Purge device9.19 >>PT 池Pit9.20 >>SHLT 棚Shelter9.21>> COFF 围堰Cofferdam9.22>> FL 楼板Floor9.23>> PF 平台Plateform10、尺寸标注10.1 >>>EL 标高Elevation10.2>> BOP 管底Bottom of pipe10.3>> COP 管中心Center of pipe10.4>> TOP 管顶Top of pipe10.5 >>FOB 底平Flat on bottom10.6>> FOT 顶平Flat on top10.7>> CL(屯) 中心线Center line10.8>> TL 切线Tangent line10.9>> SYM 对称的Symmetrical10.10>> BOS 支架底Bottom of support10.11 >>TOS 支架顶Top of support10.12>> CL 净距（净空）Clearance10.13>> CTC 中心至中心Center to center10.14>> CTF 中心至面Center to face10.15>> CTE 中心至端部Center to end10.16>> ETE 端到端End to end10.17>> FEF 法兰端面Flange and face10.18 >>FTF 面到面Face to face10.19 >>D 直径Diameter10.20>> DN 公称直径Nominal diameter10.21 >>ID 内径Inside diameter10.22>> OD 外径Outside diameter10.23>> DIM 尺寸Dimension10.24>> MAX 最大Maximum10.25 >>MIN 最小Minimum10.26>> AVG 平均Average10.27>> APP 约、近似Approximate10.28>> PT.EL 点标高Point elevation11 图表11.1>> PFD 工艺流程图Process flow diagram11.2>> PID 管道和仪表流程图Piping & instrument diagram11.3>> COD 接续图Continued on drawing11.4>> DTL 详图Datail11.5>> SPDWG 管段图Spool drawing (each line isometric drawing) 11.6>> DWGNO 图号Drawing number11.7>> DWGI 所在图号Drawing identification11.8>> LOW 材料表List of material11.9>> MTO 汇料Material take-off11.10>> APPX 附录Appendix11.11>> JOB. No. 工号Job Number11.12>> BEDD 基础工程设计数据Basic engineering design data 11.13>> DEDD 详细工程设计数据Detail engineering design data 11.14>> REV. No. 修改号Recision number11.15>> REF DWG 参考图Reference drawing11.16 >>SC 采样接口Sample connection12、操作方式及工作参数12.1>> AUT 自动Automatic12.2>> ML 手动Manual control12.3>> CHOP 链条操作Chain operated12.4 >>CSC 铅封关Car seal close12.5>> CSO 铅封开Car seal open12.6>> LC 锁闭Lock closed12.7>> LO 锁开Lock open12.8>> NC 正常关Normally close12.9>> NO 正常开Normally open12.10>> ATM 大气压Atmosphere12.11>> PN 公称压力Nominal pressure12.12>> A 绝压12.13>> G 表压12.14>> (T) 温度Temperature12.15>> (P) 压力Pressure13、施工13.1>> W 焊接Welding13.1.1> AW(SMAW) 电弧焊Arc welding13.1.2> GSAW 气体保护电弧焊Gas shielded-acr welding13.1.3> EFW 电熔焊Elecric fusion welding13.1.4 >ERW 电阻焊Electric Resistance welding13.1.5> GW 气焊Gas welding13.1.6> LW 搭接焊Lap welding13.1.7> BW 对焊Butt welding13.1.8 >TW 定位焊Tack welding13.1.9> SW 承插焊Socket welding13.1.10> CW 连续焊Continuous welding13.1.11> SEW 密封焊Seal welding13.1.12> SFG 堆焊Surfacing13.1.13> FW 现场焊接Field welding13.1.14 > TIG(GTAW) 钨极惰性气体保护焊(氩弧焊)Gas Tungsten Arc Weld 13.2 >>HT 热处理Heat treatment13.2.1>> PH 预热Preheating13.2.2 >SR 应力消除Stress relief13.2.3> PWHT 焊后热处理Post weld heat treatment13.3> EIT 检查、探伤和实验Examination, inspection & testing13.3.1> VE 外观检查Visual examination13.3.2>> UI (UT) 超声探伤Ultrasonic inspection (test)13.3.3>> RI (RT) 射线探伤Radiographic inspection (test)13.3.4> MPI (MT) 磁粉探伤Magnetic particle inspection (test) 13.3.5> LPI (PT) 液体渗透检验Liquid penterant inspection (test) 13.3.6> HADT 硬度实验Hardness testing13.3.7> HYDT 水压实验Hydraulic testing13.3.8> PNET 气压实验Pneumatic testing13.3.9> CE 焊条Covered electrode13.3.10> WW 焊丝Welding wire13.3.11> ASSY 装配、组合Assembly13.3.12 >F 现场Field13.3.13> F/F 现场制造Field faricated13.3.14> SF 现场决定Suit in field13.3.15> CSP 冷紧Cold spring13.3.16> BCT 螺栓冷紧Bolt cold tightening13.3.17> BHY 螺栓热紧Bolt hot tightening13.3.18> CO 清洗口Clean out13.3.19> ANNY 退火Annealed13.4 >PE 平端面Plain end13.5 >BE 坡口端Belelled end13.6> THR 螺纹Thread13.7 >HB 布氏硬度Brinnel hardness13.8> RC 洛氏硬度14、其他14.1> FDN 基础Foundation14.2> INF 信息（资料）Information14.3 >REF 参考Reference14.4 >REV 修改Revision14.5 >SEQ 序号（顺序）Sequence14.6> W/E 设备带来With equipment14.7> W/I 仪表带来With instrument14.8> CM 色标Colour mark14.9> CA 腐蚀裕度Corrosion allowance14.10> UTL 公用系统Utility14.11> UC 公用工程接头Utility connection14.12> QTY 数量Quantity14.13 >WT 重量Weight14.14> MHR 工时Man hour14.15> BC 螺栓分布圆Bolt circle14.16> HP 高点High point14.17> LP 低点Low point14.18> SUC 吸入（口）Suction14.19 DIS 排出（口）Discharge14.20> SO 蒸气吹扫（口）Steam out14.21> NPT 美国标准锥管螺纹National standard taper pipe thread 14.22> NPS 美国标准直管螺纹National standard straight pipe thread 14.23> DR 排液Drain14.24> VT 放气Vent14.25> RTG （压力）等级Rating14.26> CL 等级Class14.27 >SMLS 无缝Seamless14.28> 螺旋缝 Spiral seam。

管件常用英文词汇附缩写I

弯头joint弯头angle fittings; bent pipe; elbow; knee弯头扳手bent-handle wrench; bent spanner弯头车刀angular tool弯头持针钳curved needle holders弯头刀架knee tool弯头道钉brob弯头管swan neck弯头键gib head key弯头接合knee-joint弯头螺栓bolt with one end bent back弯头锁紧螺母elbow jam unt弯头套管elbow union弯头套筒扳手offset socket wrench弯头脱水器elbow separator弯头芯盒elbow core box活接活接loose joint活接地swinging earth活接结合articulated joint活接联接器joint coupling活接三通union tee活接头articulation; union swivel; union活接头螺母union nut活接头螺栓swing bolt活接头套管union thimble活接卸槽articulated chute (浇混凝土用的)三通三通tee bend; tee branch; tee joint; tee conneetion; tee fitting; wye; Y; yoke 三通玻璃栓three-way glass stopcock三通道放大器three-channel amplifier; three-path amplifier三通道自动驾驶仪three-dimensional autopilot三通电缆分线盒three-way coupling box三通阀tee valve; three-port valve; three-way valve; triple valve三通阀盖triple-valve cap三通阀活塞triple-valve piston三通阀联箱three way valve menifold三通阀体triple body; triple-valve body三通管single sweep tee; T-branch (pipe); three-limb tube三通管接头tee pipe coupling三通横长horizontal length of tee三通换向旋塞three-way reversing cock三通活栓three-way cock三通货协定triparties currency agreement三通接头tee coupling; tee fitting; tee union; three-way piece; three-way connection 三通接线夹three-way connector三通开关three-way cock三通控制阀three-way control valve三通连接tee junction三通路循环器three-terminal circulator三通式热风炉three-pass stove三通天线转发开关triplexer三通筒triple cylinder三通筒垫密片triple-cylinder gasket三通弯头three-way elbow三通旋塞tee cock; three-way cock; three-throw tap三通循环器three-terminal circulator三通液体流量计tee fluid flow meter三通闸阀treble ported slide valve直通直通direct connection; straight in; straight bore; through; feed(-)through; once-through 直通拨号through dial(l)ing直通测量线路end-to-end measurement直通单向阀in-line check valve; straight check valve; straightway check valve直通道路through road直通的through and through直通地dead earth; dead ground直通垫外底through midsole直通电报telex直通电报通信telex communication直通电流through current直通电流偏置through current bias直通电路direct circuit直通阀pass valve; straight-through valve; straightway valve; through valve 直通干馏炉through retort直通锅炉once-through boiler直通换料once-through refuelling直通回路straight circuit直通汇接呼叫制straight forwardjunction working直通监控through supervision直通接头straight coupling; straight fitting直通接线装置through joint直通街道through expressway; through street; throughway直通进位standing carry直通开关globe cock直通空气制动阀straight air brake valve直通空气制动器straight air brake直通快动阀straight-through fast acting valve直通连接straight-through joint直通裂化straight-through cracking直通流动straight through flowS型弯管“S” bend单侧偏置90º弯管Single offset “U”bendU型弯管“U” bend双偏置U型膨胀弯管Double offset expansio n “U” bend斜接弯头Mitre elbow斜接弯Mitre bend三节斜接管4-piece mitre bend折皱弯管Corrugated bend法兰法兰端Flanged end坡口端；对焊端Beveled end [BEV.E];Butt welded end平端Plain end [PE]承插焊端Socket welding end螺纹端Threaded end [TE]承口Bell end焊接端Welding end钢管法兰Steel pipe flange螺纹法兰Threaded flange滑套法兰（平焊法兰) Slip-on-welding flange Slip-on [SO] flange 承插焊法兰Socket welding flange松套法兰Lap joint flange [LJF]对焊法兰Weld neck flange [WNF]法兰盖Blind flange ; Blind孔板法兰Orifice flange异径法兰Reducimg flange盘座式法兰Pad type flange松套带颈法兰Loose hubbed flange板式平焊法兰Welding plate flange松套法兰Lap joint flange [LJF]对焊法兰Weld neck flange [WNF]法兰盖Blind flange ; Blind孔板法兰Orifice flange异径法兰Reducimg flange盘座式法兰Pad type flange松套带颈法兰Loose hubbed flange板式平焊法兰Welding plate flange对焊环（与stubend相似）Welding neck collar（与stubend相似）平焊环Welding-on collar管端突缘Stub end翻边端Lapped pipe end松套板式法兰Loose plate flange压力级Pressure rating ; Pressure rating class压力-温度等级Pressure-temperature rating法兰密封面；法兰面Flange facing突面Raised face [RF]凸面Male face [MF]凹面Female face [FMF]榫面Tongue face槽面Groove face环连接面Ring joint face短半径弯头Short radius elbow长半径180º弯头Long radius return短半径180º弯头Short radius return带侧向口的弯头（右向或左向）Side outlet elbow(Right hand or left hand) 双支管弯头Double branch elbow三通Tee异径三通Reducing tee等径三通Straight tee带侧向口的三通（右向或左向）Side outlet tee (Right hand or left hand) 异径三通（分支口为异径）Reducing tee(Reducing on outlet)异径三通（一个直通口为异径）Reducing tee (Reducing on one run)堵头Plug短管Nipple异径短节Reducing nipple异径短节(外螺纹或无螺纹) Swage nippe (选自BS 3800)弯头Elbow异径弯头Reducimg elbow带支座弯头Base elbow长半径弯头Long radius elbow管子（按照标准规格制造的配管用管）Pipe管子（不按照标准规格制造的其他用管) Tube钢管Steel pipe铸铁管Cast iron pipe衬里管Lined pipe复合管Clad pipe碳钢管Carbon steel [C.S.]pipe合金钢管Alloy steel pipe不锈钢管Stainless steel [S.S.]pipe奥氏体不锈钢管Austenitic stainless pipe铁合金钢管Ferritic alloy steel pipe扎制钢管Wrought-steel pipe段铁管Wrought-iron pipe无缝钢管Seamless[SMLS]steel pipe焊接钢管Welded steel pipe电阻焊钢管Electric-resistance-welded steel pipe电熔（弧）焊钢板卷管Electric-fusion (arc)-welded steel-plate pipe 螺旋焊接钢管Spiral welded steel pipe镀锌钢管Galvanized steel pipe热轧无缝钢管Hot-rolling seamless pipe冷拉无缝钢管Cold-drawing seamless pipe水煤气钢管Water-gas steel pipe塑料管Plastic pipe玻璃管Glass tube橡胶管Rubber tube壁厚Wall thickness(WT)壁厚系列号Schcdule number架厚的，加强的Extra heavy; Extra stromg双倍加强的，双倍加厚的Double extra heavy; Double extra strong 预制弯管Fabricated pipe bend跨越弯管( )形Cross-over bend偏置弯管（）形Offset bend锥管螺纹密封焊连接Seal-welded taper pipe threaded joint承插焊连接（接头）Socket welded joint承插连接（接头）Bell and spigot joint焊接接头Welded joint环垫接头Ring joint[RJ]万向接头Universal软钎焊连接（接头）Soldered joint搭接接头Lapped joint外侧厚度切斜角Bevel for outside thickness内侧厚度切斜角Bevel for inside thickness内外侧厚度切斜角Bevel for combined thickness法兰式的Flanged [FLGD]对焊的Butt welded [BW]螺纹的Threaded [THD]承插焊的Socket welded [SW]小端为平的Small end plain [SEP]大端为平的Large end plain [LEP]两端平Both ends plain [BEP]小端带螺纹Small end thread [SET]大端带螺纹Large end thread一端带螺纹One end thread两端带螺纹Both ends thread整体管法兰Integral pipe flange光滑突面Smooth raised face [SRF]法兰面加工Facing finish粗糙度Roughness光滑的Smooth齿形的Serrated均方根Root mean square [RMS]算术平均粗糙高度Arithmetical average roughness height[AARH] HALF COUPLING 单承口管箍1.1 P 管子Pipe1.2.3 MEL 斜接弯头（虾米腰弯头）Mitre elbow1.2.4 REL 异径弯头Reducing elbow1.3 T 三通Tee1.3.1 LT 斜三通Lateral tee1.3.2 RT 异径三通Reducing tee1.4 R 异径管接头（大小头）Reducer1.4.1 CR 同心异径管接头（同心大小头）Concentric reducer 1.4.2 ER 偏心异径管接头（偏心大小头）Eccentric reducer1.5 CPL 管箍Coupling1.5.1 FCPL 双头管箍Full coupling1.5.2 HCPL 单头管箍Half coupling1.5.3 RCPL 异径管箍Reducing coupling1.6 BU 内外螺纹接头Bushing1.7 UN 活接头Union1.8 HC 软管接头Hose coupler1.9 SE 翻边短节Stub end1.10 NIP 短节Pipe nipple or straight nipple1.10.1 SNIP 异径短节Swaged nipple1.11 CP 管帽（封头）Cap1.12 PL 管堵（丝堵）Plug1.13 BLK 盲板Blank1.13.1 SB 8字盲板Spectacle blind (blank)1.14 RP 补强板Reinforcing padHARDNESS 硬度（最大值197）HEAT CONTROL NUMBER 热处理炉号HEAT TREATMENT（热处理），有缝部分填N，无缝部分填A HEX HEAD BUSHING 卜申HEX HEAD PLUG 六角塞头HEX NIPPLE 六角立布HIGH PRESSURE ELBOW 高压弯头HIGH PRESSURE REDUCER 高压异径管HIGH PRESSURE TEE 高压四通hydraulic hose液压软管HJ 环境保护行业标准hose clip软管卡子hose protector软管保护管hot-rolling seamless pipe热轧无缝钢管HR 热轧INNER DIAMETER （简）ID 内径INSERT 变径接头integral pipe flange整体管法兰JIS 日本工业标准jumper hose跨接软管jumper lose connection跨接软管连接器Lap Joint Flanges对焊环松套法兰lap joint flange (LJF) 松套法兰lapped joint搭接接头，松套连接lapped pipe end翻边端large end plain (LEP) 大端为平的1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbowk半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand) 双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet)异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet) 异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull he ad)45°斜三通45°lateral45°斜三通（支管为异径）45°lateral (reducing on branch)45°斜三通(一个直通口为异径) 45°lateral (reducing on one run)45°斜三通(一个直通口及支管为异径) 45°lateral (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and out let)异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run an d both outlet)异径管reducer同心异径管concentric reducer两端带螺纹both end thread (BET)一端带螺纹one end thread (OET)支管连接branch connection焊接支管branch pipe welded directly to the run pipe法兰端flanged end坡口端beveled end (BE)对焊端butt welded end平端plain end (PE)承插焊端socket welding end螺纹端threaded end (TE)承口bell end焊接端welding end法兰连接（接头）flanged joint对焊连接（接头）butt welded joint螺纹连接，管螺纹连接threaded joint, pipe threaded joint 锥管螺纹密封焊连接seal-welded taper pipe threaded joint 承插焊连接（接头）socket welded joint承插连接（接头）bell and spigot joint环垫接头ring joint (RJ)万向接头universal joint软钎焊连接（接头）soldered joint搭接接头，松套连接lapped joint外侧厚度切斜角bevel for outside thickncss内侧厚度切斜角bevel for inside thickness内外侧厚度切斜角bevel for combined thickness法兰式的flanged (FLGD)对焊的butt welded (BW)螺纹的threaded (THD)承插焊的socket welded (SW)小端为平的small end plain (SEP)大端为平的large end plain (LEP)两端平both ends plain (BEP)小端带螺纹small end thread (SET)大端带螺纹large end thread (LET)多波multiple bellow压力平衡式膨胀节pressure balanced expansion带铰链膨胀节hinged expansion joint轴向位移型膨胀节axial movement type expansion joint 自均衡膨胀节（外加强环）self-equalizing expansion joint 带接杆膨胀节tied expansion joint万向型膨胀节universal type expansion joint球形补偿器ball type expansion joint填函式补偿器slip type (packed type) expansion joint 单向滑动填料函补偿器single actionpacked slip joint 1.7.2 管道特殊元件Piping Special Element软管接头hose connection (HC)快速接头quick coupling金属软管metal hose橡胶管rubber hose挠性管flexible tube鞍形补强板reinforcing saddles补强板reinforcement pad特殊法兰special flange漏斗funnel排液环drip ring排液漏斗drain funnel插板blank垫环spacer8字盲板spectacle blind; figure 8 blind限流孔板restriction orifice爆破片rupture disk法兰盖贴面protective disc费托立克接头victaulic coupling1.8 端部连接End Connection（水）龙头bibb; bib; faucet抽出液阀（小阀）bleed valve旁路阀by-pass valve软管阀hose valve混合阀mixing valve破真空阀vacuum breaker冲洗阀flush valve第一道阀；根部阀primary valve根部阀root valve总管阀header valve事故切断阀emergency valve1.7 管道特殊件Piping Specialty1.7.1 管道特殊件（组件）粗滤器strainer过滤器filter临时粗滤器（锥型）temporary strainer (cone type)y 型粗滤器y-type strainerT型粗滤器T-type strainer永久过滤器permanent filter丝网粗滤器gauze strainer洗眼器及淋浴器eye washer and shower视镜sight glass阻火器flame arrester喷嘴；喷头spray nozzle取样冷却器sample cooler消声器silencer膨胀节expansion joint波纹膨胀节bellow expansion joint单波single bellow双波double bellow杠杆重锤式lever and weight type引导阀操纵的安全泄气阀pilot operated safety valve复式安全泄气阀twin type safety valve罐底排污阀flush-bottom tank valve电磁阀solenoid valve, solenoid operated valve电动阀electrically operated valve, electric-motor operated valve 气动阀pneumatic operated valve低温用阀cryogenic service valve蒸汽疏水阀steam trap机械式疏水阎mechanical trap浮桶式疏水阀open bucket trap, open top bucket trap浮球式疏水阀float trap倒吊桶式疏水阀inverted bucket trap自由浮球式疏水阀loose float trap恒温式疏水阀thermostatic trap金属膨胀式蒸汽疏水阀metal expansion steam trap液体膨胀式蒸汽疏水阀liquid expansion steam trap双金属膨胀式蒸汽疏水阀bimetallic expansion steam trap压力平衡式恒温疏水阀balanced pressure thermostatic trap热动力式疏水阀thermodynamic trap脉冲式蒸汽疏水阀impulse steam trap放气阀（自动放气阀）air vent valve (automatic air vent valve) （疏水阀用）平板式滑动闸阀slab type sliding gate valve盖阀flat valve换向阀diverting valve, reversing valve热膨胀阀thermo expansion valve自动关闭阀self-closing gate valve自动排液阀self-draining valve管道盲板阀line-blind valve挤压阀squeeze valve（用于泥浆及粉尘等）偏心阀板蝶阀offset disc burerfly valve; eccentric butterfly valve 斜阀盘蝶阀canted disc butterfly valve连杆式蝶阀link butterfly valve8) 柱塞阀piston type valve(9) 旋塞阀plug valve三通旋塞阀three-way plug valve四通旋塞阀four-way plug valve旋塞cock衬套旋塞sleeve cock(10) 隔膜阀diaphragm valve橡胶衬里隔膜阀rubber lined diaphragm valve直通式隔膜阀straight way diaphragm valve堰式隔膜阀weir diaphragm valve(11) 夹紧式胶管阀pinch valve（用于泥浆、粉尘等）(12) 止回阀check valve升降式止回阀lift check valve旋启式止回阀swing check valve, flap check valve落球式止回阀ball check valve弹簧球式止回阀spring ball check valve双板对夹式止回阀dual plate wafer type check valve无撞击声止回阀non-slam cheek valve底阀foot valve切断式止回阀stop check valve; non-return valve活塞式止回阀piston check valve斜翻盘止回阀tilting disc check valve蝶式止回阀butterfly check valve1.6.3 其它用途的阀安全泄气阀safety valve (SV)安全泄液阀relief valve (RV)安全泄压阀safety relief valve升杆式（明杆）rising stem (RS)非升杆式（暗杆）non-rising stem (NRS)指示器/限位器indicator/stopper注油器grease injector可更换的阀座环renewable seat ring1.6.2 常用阀(1）闸阀gate valve平行双闸板double disc parallel seat开口楔形闸板split wedge挠性整体楔形闸扳flexible solid wedge整体楔形闸板solid wedge塞型闸阀plug gate valve直通型闸阀through conduit gate valve(2) 截止阀globe valve球心型阀盘globe type disc塞型阀盘plug type disc可转动的阀盘swivel disc(3) 节流闪阀throttle valve针阀needle valve(4) 角阀angle valve(5) Y型阀（Y 型阀体截止阀）Y-valve (Y-body globe valve)(6) 球阀ball valve三通球阀3-way ball valve装有底轴的trunnion mounted耐火型fire safe type浮动球型floating ball type防脱出阀杆blowout proof stem(7) 蝶阀butterfly valve对夹式（薄片型）wafer type凸耳式lug type螺栓连接的阀盖bolted bonnet (BB)活接阀盖（帽）union bonnet (cap)螺栓连接的阀帽bolted cap (BC)焊接阀盖welded bonnet (WB)本体阀杆密封body stem seal石棉安全密封asbestos emenen seal倒密封back seal压力密封的阀盖pressure-tight bonnet动力操纵器powered operator电动操纵器electric motor operator气动操纵器pneumatic operator液压操纵器hydraulic operator快速操纵器quick-acting operator滑动阀杆sliding stem正齿轮传动spur gear operated伞齿轮传动bevel gear operated扳手操作wrench operated链轮chain wheel手轮hand wheel手柄hand lever (handle)气缸（或液压缸）操纵的cylinder operated链条操纵的chain operated等径孔道full bore; full port异径孔道reducing bore, reduced port,venturi port 短型short pattern紧凑型（小型）compact type笼式环lantern ring压盖gland阀杆填料stem packing阀盖垫片bonnet gasket斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness1.4 法兰Flange (FLG）整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip-on flange (SO); slip-on wel ding flange承插焊法兰socket welding flange松套法兰lap joint flange (LJF)对焊法兰welding neckflange (WNF)法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar （与stub end相似）平焊环welding-on collar突缘短节stub end, lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力—温度等级pressure-temperature rating法兰密封面，法兰面flange facing突面raised face (RF)凸面male face (MF)凹面female face (FMF)榫面tongue face。

管件常用英文词汇附缩写I

管道及管件常用词汇

管道及管件常用词汇以下是管道及管件常用词汇：1. 管道（Pipe）2. 管件（Fitting）3. 弯头（Elbow）4. 管道接头（Pipe joint）5. 管道法兰连接（Flanged connection）6. 焊接连接（Welded connection）7. 螺纹连接（Threaded connection）8. 肩型连接（Shoulder connection）9. 快速接头（Quick coupling）10. 管道套筒（Pipe sleeve）11. 管道补偿器（Pipe compensator）112. 管道支架（Pipe hanger）13. 管道支撑（Pipe support）14. 管道附件（Pipe accessory）15. 管道密封（Pipe sealing）16. 管道阀门（Pipe valve）17. 膨胀节（Expansion joint）18. 排气阀（Air vent valve）19. 抽水阀（Drain valve）20. 截止阀（Stop valve）21. 调节阀（Control valve）22. 安全阀（Safety valve）23. 蝶阀（Butterfly valve）24. 球阀（Ball valve）25. 压力表（Pressure gauge）226. 温度计（Thermometer）27. 流量计（Flow meter）28. 规格（Specification）29. 材质（Material）30. 内径（Inner diameter）31. 外径（Outer diameter）32. 壁厚（Wall thickness）33. 长度（Length）34. 压力等级（Pressure rating）35. 温度等级（Temperature rating）36. 标准（Standard）37. 法兰（Flange）38. 异径（Reducer）39. 等径（Equal tee）340. 止回阀（Check valve）4。

常用管件管道配件中英文对照

P 管子Pipe EL 弯头Elbow ELL 长半径弯头Long radius elbow ELS 短半径弯头Short radius elbow MEL 斜接弯头（虾米腰弯头）Mitre elbow REL 异径弯头Reducing elbow T 三通Tee LT 斜三通Lateral tee RT 异径三通Reducing tee R 异径管接头（大小头）Reducer CR 同心异径管接头（同心大小头）Concentric reducer CPL 管箍Coupling ER 偏心异径管接头（偏心大小头）Eccentric reducer FCPL 双头管箍Full coupling HCPL 单头管箍Half coupling RCPL 异径管箍Reducing coupling BU 内外螺纹接头Bushing UN 活接头Union HC 软管接头Hose coupler SE 翻边短节Stub end NIP 短节Pipe nipple or straight nipple SNIP 异径短节Swaged nipple CP 管帽（封头）Cap PL 管堵（丝堵）Plug BLK 盲板Blank 8字盲板Spectacle blind (blank) RP 补强板Reinforcing pad法兰PLG 法兰Flange WNF 对焊法兰Welding neck flange SOF 平焊法兰Slip-on flange SWF 承插焊法兰Socket-welding flange T 螺纹法兰Threaded flange LJ 松套法兰Lapped joint flange REDF 异径法兰Reducing flange BF 法兰盖（盲法兰）Blind flange FSF 法兰密封面Flange scaling face FF 全平面Flat face RF 凸台面Raised face MFF 凹凸面Male and female face LF 凹面Female face LM 凸面Male face RJ 环连接面Ring joint face TG 榫槽面Tongue and groove face TF 榫面Tongue face垫片G 垫片Gasket NMG 非金属垫片Non-metallic gasket AG 石棉垫片Asbestos gasket RG 橡胶垫片Rubber gasket TEG 聚四氟乙烯包复垫片PTFE envelope gasket SMG 半金属垫片Semimetallic gasket MJG 金属包垫片Meta-jacket gasket SWG 缠绕式垫片Spiral wound gasketMG 金属垫片Metallic gasket FMG 金属平垫片Flat metallic gasket SMSG 齿形金属垫片Solid metal serrated gasket LER 透镜式金属环垫Lens ring gasket OCR 八角形金属环垫Octagonal ring gasket OVR 椭圆形金属环垫Oval ring gakset IR/OR 内外定位环Inner ring and outer ring IR 内定位环Inner ring OR 外定位环Outer ring坚固件B 螺栓Bolt SB 螺柱Stud bolt NU 螺母Nut TB 花蓝螺母Turnbuckle WSR 垫圈Washer SWSR 弹簧垫圈Spring washerGV 闸阀Gate valve GLV 截止阀Globe valve CHV 止回阀Check valve BUV 蝶阀Butterfly valve BAV 球阀Ball valve PV 旋塞阀Plug valve (cock) CV 调节阀Control valve SV 安全阀Safety valve RV 减压阀Pressure reducing valve ST 蒸汽疏水阀Steam trap PRV 泄压阀Pressur relief valve BV 呼吸阀Breather valve NV 针形阀Needle valve A V 角阀DV 隔膜阀TWV 三通阀SGV 插板阀尺寸标注EL 标高Elevation BOP 管底Bottom of pipe COP 管中心Center of pipe TOP 管顶Top of pipe FOB 底平Flat on bottom FOT 顶平Flat on top CL(屯) 中心线Center line TL 切线Tangent line SYM 对称的Symmetrical BOS 支架底Bottom of support TOS 支架顶Top of support CL 净距（净空）Clearance CTC 中心至中心Center to center CTF 中心至面Center to face CTE 中心至端部Center to end ETE 端到端End to end FEF 法兰端面Flange and face FTF 面到面Face to face D 直径Diameter DN 公称直径Nominal diameter ID 内径Inside diameter OD 外径Outside diameter DIM 尺寸Dimension MAX 最大Maximum MIN 最小Minimum A VG 平均Average APP 约、近似Approximate PT.EL 点标高Point elevation 管道上用的小型设备SPR 气液分离器Separator FA 阻火器Flame arrester SR 过滤器Strainer SRY Y型过滤器Y-type strainer SRT T型过滤器T-type strainer SRB 桶式过滤器Bucket type strainer TSR 临时过滤器Temporary strainer SIL 消声器Silencer SG 视镜Slight glass SC 取样冷却器Sample cooler DF 排液漏斗Drain funnel LM 管道混合器Line mixer RO 限流孔板Restriction orifice MO 混合孔板Mixing orifice RD 爆破片（爆破膜）Rupture disk EJ 补偿器Expan sion joint 隔热、伴热INS 隔热Thermal insulation H 保温Hot insulation C 保冷Cold insulation P 防烫伤隔热Personnel protection insulation T&I 伴热Tracing and insulation T 管道伴热（冷）Tracing EST 蒸汽外伴热External steam tracing IST 蒸汽内伴热Internal steam tracing SJT 蒸汽夹套伴热Steam-jacket tracing ET 电伴热Electric tracing装置布置CN 建北Construction north E 东East W 西West 南South N 北North H 水平Horizontal V 竖直、铅直、直立Vertical GRD 地坪Ground UG 地下Underground BL 装置边界线Battery limit line ML 接续分界线Match line ESEW 事故沐浴洗眼器Emergency shower and eye washer PT 池Pit HS 软管站Hose station PS 管道支架（管架）Piping support PR 管桥Pipe rack STRU 构架（构筑物）Structure BLDG 建筑物Building PD 清扫设施Purge device SHLT 棚Shelter COFF 围堰Cofferdam FL 楼板Floor PF 平台Plateform 图表PFD 工艺流程图Process flow diagramPID 管道和仪表流程图Piping & instrument diagramCOD 接续图Continued on drawingDTL 详图DatailSPDWG (ISODWG) 管段图Spool drawing (each line isometric drawing)DWGNO 图号Drawing numberDWGI 所在图号Drawing identificationLOW 材料表List of materialMTO 汇料Material take-offAPPX 附录AppendixJOB. No. 工号Job NumberBEDD 基础工程设计数据Basic engineering design dataDEDD 详细工程设计数据Detail engineering design dataREV. No. 修改号Recision numberREF DWG 参考图Reference drawingSC 采样接口Sample connection操作方式及工作参数AUT 自动Automatic ML 手动Manual control CHOP 链条操作Chain operated CSC 铅封关Car seal close CSO 铅封开Car seal open LC 锁闭Lock closed LO 锁开Lock open NC 正常关Normally close NO 正常开Normally open ATM 大气压Atmosphere PN 公称压力Nominal pressureA 绝压G 表压(T) 温度Temperature(P) 压力PressureW 焊接Welding AW 电弧焊Arc welding GSAW 气体保护电弧焊Gas shielded-acr welding EFW 电熔焊Elecric fusion welding ERW 电阻焊Electric Resistance welding GW 气焊Gas welding LW 搭接焊Lap welding BW 对焊Butt welding TW 定位焊Tack welding SW 承插焊Socket welding CW 连续焊Continuous welding SEW 密封焊Seal welding SFG 堆焊Surfacing FW 现场焊接Field welding HT 热处理Heat treatment PH 预热Preheating SR 应力消除Stress relief PWHT 焊后热处理Post weld heat treatment EIT 检查、探伤和实验Examination, inspection & testingVE 外观检查Visual examinationUI (UT) 超声探伤Ultrasonic inspection (test)RI (RT) 射线探伤Radiographic inspection (test)MPI (MT) 磁粉探伤Magnetic particle inspection (test)LPI (PT) 液体渗透检验Liquid penterant inspection (test)HADT 硬度实验Hardness testing HYDT 水压实验Hydraulic testing PNET 气压实验Pneumatic testing CE 焊条Covered electrode WW 焊丝Welding wire ASSY 装配、组合Assembly F 现场Field F/F 现场制造Field faricated SF 现场决定Suit in field CSP 冷紧Cold spring BCT 螺栓冷紧Bolt cold tightening BHY 螺栓热紧Bolt hot tightening CO 清洗口Clean out ANNY 退火Annealed PE 平端面Plain end BE 坡口端Belelled end THR 螺纹Thread HB 布氏硬度Brinnel hardness RC 洛氏硬度其他FDN 基础Foundation INF 信息（资料）Information REF 参考Reference REV 修改Revision SEQ 序号（顺序）Sequence W/E 设备带来With equipment W/I 仪表带来With instrument CM 色标Colour mark CA 腐蚀裕度Corrosion allowance UTL 公用系统Utility UC 公用工程接头Utility connection QTY 数量Quantity WT 重量Weight MHR 工时Man hour BC 螺栓分布圆Bolt circle HP 高点High point LP 低点Low point SUC 吸入（口）Suction DIS 排出（口）Discharge SO 蒸气吹扫（口）Steam out NPT 美国标准锥管螺纹National standard taper pipe threadNPS 美国标准直管螺纹National standard straight pipe threadDR 排液Drain VT 放气VentRTG （压力）等级RatingCL 等级Class SMLS 无缝Seamlessslide plate滑板; 滑块 bolt 马蹄螺栓; 马蹄形螺栓non-ferrous pipe saddle 有色的, 非铁或钢的(金属)管座; 鞍形管夹pipe clamp 管夹 strap 吊管带spring wedge plate 弹簧楔片 compressed gasket 压缩垫expansion bolt 膨胀螺栓 lower component 地面的基础支撑lug plate 接线板,焊片 beam attachment 横梁附件weldless eye nut 无焊缝的环首螺母螺配管材料和等级M 金属材料Metallic material CS 碳钢Carbon steel CAS 铸钢Cast steel FS 锻钢Forged steel AS 合金钢Alloy steel SS 不锈钢Stainless steel AUST SS 奥氏体不锈钢Austenitic stainless-steel CI 铸铁Cast iron MI 可锻铸铁Malleable iron DI 球墨铸铁Ductile iron AL 铝Aluminum BRS 黄铜Brass BRZ 青铜Bronze CU 紫铜Copper LAS 低合金钢Low alloy steel FLAS 低合金锻钢Forged low alloy steel CLAS 低合金铸钢Cast low alloy steel THK 壁厚Thickness SCH 表号Schedule number STD 标准Standard XS 加强Extra strong XXS 特强Double extra strong。

管件英文对照

弯头(Elbow):卡箍式弯头(Clamp Elbow),焊接式弯头(Weld Elbow),螺纹式弯头(Threaded Elbow);三通(Tee):卡箍式三通(Clamp Tee),焊接式三通(Weld Tee),螺纹式三通(Threaded Tee);四通(Cross):卡箍式四通(Clamp Cross),焊接式三通(Weld Cross),螺纹式三通(Threaded Cross);同心大小头(Concentric Reducer);偏心大小头(Eccentric Reducer);变径管(Reducer);活接/由任(Union);螺母(Nut);螺纹接头(Male);平接头(Liner);垫圈(Gasket);卡箍接头(Ferrule);软管接头(Hose Coupling);盲板(Banlk);卡箍(Clamp);人孔盖(Manways);泵(Pump);蝶阀(Butterfly Valve);止回阀(Check Valve);隔膜阀(Diaphragm Valve);球阀(Ball Valve);过滤器(Filter);取样阀/采样阀(Sample Valve);换向阀(Reversing Valve);呼吸器(Rebreather);地漏(Floor Drain);视镜(Sight Glass);清洗球(Cleaning Ball);管支架(Pipe Holder);卫生管(Sanitary Tube)。

材质有SS304，SS316或SS316L不锈钢，抗锈且抗腐蚀，耐受CIP ( Clean-In-Place )清洗程序，适合用于牛乳、食品、啤酒、饮料、制药、生技、化工、净水处理工厂以及其它高科技产业工厂。

常用管件管道配件中英文对照

常用管件管道配件中英文对照１.管件系列1。

1>>P 管子Pipe1。

2>> EL 弯头Elbow1。

2.1〉ELL 长半径弯头Long radius elbow1。

2.2> ELS 短半径弯头Short radius elbow1.2。

3〉MEL 斜接弯头（虾米腰弯头) Mitre elbow1。

2.4〉REL 异径弯头Reducing elbow1。

3>〉T 三通Tee1。

3.1> LT 斜三通Lateral tee1.3.2〉RT 异径三通Reducing tee1.3.3〉 CROSS 四通1。

4〉〉R 异径管接头(大小头）Reducer1。

4.1> CR 同心异径管接头（同心大小头）Concentric reducer 1。

4。

2〉ER 偏心异径管接头(偏心大小头）Eccentric reducer 1。

5>> CPL 管箍Coupling1.5。

1〉FCPL 双头管箍Full coupling1.5.2〉HCPL 单头管箍Half coupling1.5.3〉RCPL 异径管箍Reducing coupling1.6>〉BU 内外螺纹接头Bushing1.7〉〉UN 活接头Union1。

8>〉HC 软管接头Hose coupler1。

9〉〉SE 翻边短节Stub end1。

10>〉NIP 短节Pipe nipple or straight nipple1.10。

1>SNIP 异径短节Swaged nipple1。

11>〉CP 管帽(封头）Cap1.12>> PL 管堵（丝堵）Plug1.13〉〉BLK 盲板Blank1。

13.1> SB 8字盲板Spectacle blind1。

14>〉PAD 补强板Reinforcing pad1.15>焊接支管台 WELDOLET1。

管道及配件中英文对照

管道及配件中英文对照化工管道词汇翻译1管道组成件Piping component1.1管子Pipe管子(按照配管标准规格制造的)pipe管子(不按配管标准规格制造的其他用管)tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless(SMLS)steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion(arc)-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe;straight pipe1.2管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbow长半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow(right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee(right hand or1eft hand)异径三通（分支口为异径）reducing tee(reducing on outlet)异径三通（一个直通口为异径）reducing tee(reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee(reducing on one run and outlet)异径三通（两个直通口为异径，双头式）reducing tee(reducing on both runs,bull head)45°斜三通45°lateral45°斜三通（支管为异径）45°lateral(reducing on branch)45°斜三通(一个直通口为异径)45°lateral(reducing on one run)45°斜三通(一个直通口及支管为异径)45°lateral(reducing on one run and branch)Y型三通（俗称裤衩）true“Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross(reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross(reducing on one run and outlet)异径四通（两个分支口为异径）reducing cross(reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross(reducing on one run and both outlet)异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss(以上带红线的单词已经查过，应该是行业很组合的名词，可以查得到)。

管道及配件中英文对照精品

管道及配件中英文对照精品管道及配件中英文对照化工管道词汇翻译1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe 螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbow长半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet) 异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet)异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull head) 45°斜三通45° lateral管道及配件中英文对照245°斜三通（支管为异径）45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run) 45°斜三通(一个直通口及支管为异径) 45° later al (reducing onone run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and outlet)异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet)异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss(以上带红线的单词已经查过，应该是行业很组合的名词，可以查得到)。