电潜泵系统构成与工作原理
合集下载
相关主题
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
bolts onto or is threaded into the pump housing • Normally be set above the perforation for sufficient cooling.
7
LT = Lower Tandem pump ( with built in intake )
9
If Upper Tandem (UT) then a discharge is built into the pump.
Built in Discharge head
UT Pump
10
UT or MT pump
Middle Tandem pump Base
Shipping Cap
11
The Bolt on Head The Middle Tandem or Lower Tandem Pump Head
4
5
Built in Discharge head
Stationary Diffuser Rotating Impeller Pump Shaft
The Pump
பைடு நூலகம்
Tubing screws in here
Pump Housing Built in Intake
Bolts to the Seal
6
22
Impeller - Cut Away
23
Diffuser 24
Diffuser
The diffuser does not rotate, it turns the fluid up into the next impeller It transforms the fluid velocity, it’s energy, into head
Impeller Vane
Downthrust Washer
Impeller Eye
Bottom Shroud Impeller Skirt
19
Impeller
Hub Upper Shroud
Vanes Lower Shroud
Skirt Eye
20
Impeller
The impeller rotates about the pump axis, with the shaft
13
Centrifugal ????
14
Centrilift Submersible Pump
Stages stacked on a shaft and compressed in a housing.
15
Cutaway of Pump Stationary diffusers Rotating (right to left) impellers
3
ESP Downhole System
The basic ESP downhole system components are ... The Pump
▪The Seal Section The Motor The Power Cable The Monitoring System (optional)
The seal bolts on here
8
If MT (middle tandem) or LT (Lower Tandem) then a flange face is the head of the pump.
Shipping Cap
Head
LT/MT = Lower/Middle Tandem pump
Mixed Flow - flow path has both axial and radial direction with respect to the pump shaft
18
Impeller Terminology
Upthrust Washer Top Shroud
Impeller Hub
A typical ESP installation
ESP System Technology Overview
2
Objective
• Upon comletion of this course, you should be able to:
Explain the uses for Electrical Submersible Pumps. List the major components of an ESP system. Explain the principle of an ESP system.
It provides the centrifugal force to the fluid - gives it energy.
21
Impeller
Fluid enters the impeller through the ‘eye’ near the shaft and exits the impeller on the outside.
16
Impeller 17
Pump Stage Hydraulic Design
ESP Stage designs fall into one of two hydraulic design categories …
Radial Flow - flow path is generally perpendicular (radial) with respect to the pump shaft
12
UT or MT pump bolts on here.
Gas separator intake (cut away). May be bolted on to the base of a MT (Middle Tandem) or UT (Upper Tandem) Pump
The Seal bolts on here.
The Pump
• Hangs from the production tubing • Lifts the fluid through the tubing to the
surface • Is a multi-stage centrifugal type • Is constructed from impellers and diffusers • Must be sized to match the well production • Has an intake and discharge that either
7
LT = Lower Tandem pump ( with built in intake )
9
If Upper Tandem (UT) then a discharge is built into the pump.
Built in Discharge head
UT Pump
10
UT or MT pump
Middle Tandem pump Base
Shipping Cap
11
The Bolt on Head The Middle Tandem or Lower Tandem Pump Head
4
5
Built in Discharge head
Stationary Diffuser Rotating Impeller Pump Shaft
The Pump
பைடு நூலகம்
Tubing screws in here
Pump Housing Built in Intake
Bolts to the Seal
6
22
Impeller - Cut Away
23
Diffuser 24
Diffuser
The diffuser does not rotate, it turns the fluid up into the next impeller It transforms the fluid velocity, it’s energy, into head
Impeller Vane
Downthrust Washer
Impeller Eye
Bottom Shroud Impeller Skirt
19
Impeller
Hub Upper Shroud
Vanes Lower Shroud
Skirt Eye
20
Impeller
The impeller rotates about the pump axis, with the shaft
13
Centrifugal ????
14
Centrilift Submersible Pump
Stages stacked on a shaft and compressed in a housing.
15
Cutaway of Pump Stationary diffusers Rotating (right to left) impellers
3
ESP Downhole System
The basic ESP downhole system components are ... The Pump
▪The Seal Section The Motor The Power Cable The Monitoring System (optional)
The seal bolts on here
8
If MT (middle tandem) or LT (Lower Tandem) then a flange face is the head of the pump.
Shipping Cap
Head
LT/MT = Lower/Middle Tandem pump
Mixed Flow - flow path has both axial and radial direction with respect to the pump shaft
18
Impeller Terminology
Upthrust Washer Top Shroud
Impeller Hub
A typical ESP installation
ESP System Technology Overview
2
Objective
• Upon comletion of this course, you should be able to:
Explain the uses for Electrical Submersible Pumps. List the major components of an ESP system. Explain the principle of an ESP system.
It provides the centrifugal force to the fluid - gives it energy.
21
Impeller
Fluid enters the impeller through the ‘eye’ near the shaft and exits the impeller on the outside.
16
Impeller 17
Pump Stage Hydraulic Design
ESP Stage designs fall into one of two hydraulic design categories …
Radial Flow - flow path is generally perpendicular (radial) with respect to the pump shaft
12
UT or MT pump bolts on here.
Gas separator intake (cut away). May be bolted on to the base of a MT (Middle Tandem) or UT (Upper Tandem) Pump
The Seal bolts on here.
The Pump
• Hangs from the production tubing • Lifts the fluid through the tubing to the
surface • Is a multi-stage centrifugal type • Is constructed from impellers and diffusers • Must be sized to match the well production • Has an intake and discharge that either