CCNA第二学期期末考试

合集下载

CCNA期末考试试题

1、要求:(1)VTP域名为benet;密码为123;启用修剪;(2)配置2台3层交换机为VTP的server模式;配置2层交换机为VTP的client模式;(3)设置SW-3L-1是VLAN 2－6的生成树根网桥;设置SW-3L-2是VLAN 7－11的生成树根网桥;在2层交换机上配置速端口与上行速链路;(4)配置路由器接口的IP地址;配置路由器启动RIP路由协议;配置路由器上的默认路由，指向10.1.1.1/24;(5)在3层交换机上配置各VLAN的IP地址;配置两台3层交换机之间的EthernetChannel;(6)配置3层交换机的路由接口;在3层交换机上配置RIP路由协议（1）（2）○1SW1-3L 配置vtp域名benetpassword 123 Server模式SW2-3L同样配置○2SW1-3L启用修剪SW2-3L同样配置○3SW3-2L配置vtp的client模式、SW4-2L、SW5-3L、SW6-3L相同配置（3）设置SW-3L-1是VLAN 2－6的生成树根网桥;设置SW-3L-2是VLAN 7－11的生成树根网桥;在2层交换机上配置速端口与上行速链路;○1SW-3L-1是VLAN 2－6的生成树根网桥;;○2设置SW-3L-2是VLAN 7－11的生成树根网桥○3SW3-2L配置速端口与上行链路，SW4-2L、SW5-2L 、SW6-2L上同样配置（4）配置路由器接口的IP地址;配置路由器启动RIP路由协议;配置路由器上的默认路由，指向10.1.1.1/24○1路由器上配置ip地址○2路由器上配置默认路由和RIP○3SW1-3L各vlan的ip地址○4SW2-3L各vlan的ip地址（5）在3层交换机上配置各VLAN的IP地址;配置两台3层交换机之间的EthernetChannel ○1在SW1-3L配置EthernetChannel;○2在SW2-3L配置EthernetChannel;（6）配置3层交换机的路由接口;在3层交换机上配置RIP路由协议○1SW1-3L上配置路由接口○2SW2-3L上配置路由接口○3SW1-3L上的RIP配置○4SW2-3L上的RIP配置○5在SW1-3L验证RIP○6在SW2-3L验证RIP2、要求:如图所示，四台路由器R1，R2，R3以及R4运行OSPF协议（要求发布各路由器的loopback0地址），R1与R2属于Area1，R2与R3属于Area0，R3与R4属于Area2。

ccna第二学期练习题中文答案..

ERouting Chapter 1 - CCNA Exploration: 路由协议和概念(版本4.0)1口令可用于限制对Cisco IOS 所有或部分内容的访问。

请选择可以用口令保护的模式和接口。

（选择三项）VTY 接口控制台接口以太网接口加密执行模式特权执行模式路由器配置模式2路由器从相连的以太网接口收到消息后，会更改哪项报头地址，再将消息从另一个接口发送出去？仅第 2 层源地址仅第 2 层目的地址仅第 3 层源地址仅第 3 层目的地址第 2 层源地址和目的地址第 3 层源地址和目的地址3请参见图示。

网络管理员已经为路由器连接到直连网络的接口配置了如图所示的IP 地址。

从路由器ping 相连网络上的主机之间相互ping 都会遭到失败。

此问题最可能的原因是什么？目的网络不存在。

路由器接口的IP 地址必须配置为网络地址而非主机地址。

必须使用no shutdown命令启用接口。

每个接口都必须使用clock rate命令配置4请参见图示。

主机 A ping 主机B。

当R4 收到对以太网接口的ping 时，哪两块报头信息包括在内？（选择两项。

）源IP 地址：192.168.10.129源IP 地址：BBBB.3333.5677源MAC 地址：5555.AAAA.6666目的IP 地址：192.168.10.33目的IP 地址：192.168.10.134目的MAC 地址：9999.DADC.12345网络管理员刚把新配置输入Router1。

要将配置更改保存到NVRAM，应该执行哪一条命令？Router1# copy running-config flashRouter1(config)# copy running-config flashRouter1# copy running-config startup-configRouter1(config)# copy running-config startup-configRouter1# copy startup-config running-configRouter1(config)# copy startup-config running-config6您需要配置图中所示的串行连接，必须在Sydney 路由器上发出以下哪条配置命令才能与Melbourne 站点建立连接？（选Sydney(config-if)# ip address 201.100.53.2 255.255.255.0Sydney(config-if)# no shutdownSydney(config-if)# ip address 201.100.53.1 255.255.255.224Sydney(config-if)# clock rate 56000Sydney(config-if)# ip host Melbourne 201.100.53.27请参见图示。

CCNA考试题

C C N A考试题(总9页) -CAL-FENGHAI.-(YICAI)-Company One1-CAL-本页仅作为文档封面，使用请直接删除第一部分：选择题1：提供可靠数据传输、流控的是OSI的第几层（）A、表示层B、网络层C、传输层D、会话层E、链路层2：子网掩码产生在那一层（）A、表示层B、网络层C、传输层D、会话层3：当路由器接收的IP报文的目的地址不是本路由器的接口IP地址，并且在路由表中未找到匹配的路由项，采取的策略是（）A、丢掉该分组B、将该分组分片C、转发该分组D、以上答案均不对4：当一台主机从一个网络移到另一个网络时，以下说法正确的是（）A、必须改变它的IP地址和MAC地址B、必须改变它的IP地址，但不需改动MAC地址C、必须改变它的MAC地址，但不需改动IP地址D、MAC地址、IP地址都不需改动5：ISO提出OSI的关键是（）A、系统互联B、提高网络速度C、为计算机制定标准D、经济利益6：OSI参考模型按顺序有哪些层（）A、应用层、传输层、网络层、物理层B、应用层、表示层、会话层、网络层、传输层、数据链路层、物理层C、应用层、表示层、会话层、传输层、网络层、数据链路层、物理层D、应用层、会话层、传输层、物理层7：LAN的拓扑形式一般以（）为主。

A、总线型B、环型C、令牌环D、载波侦听与冲突检测CSMA/CD8：网段地址154.27.0.0的网络，若不做子网划分，能支持（）台主机A、254B、1024C、65,534D、16,777,2069：路由器网络层的基本功能是（）。

A、配置IP地址B、寻找路由和转发报文C、将MAC地址解释成IP地址10：选出基于TCP协议的应用程序（）。

A、PINGB、TFTPC、TELNETD、OSPF11：某公司申请到一个C类IP地址，但要连接6个的子公司，最大的一个子公司有26台计算机，每个子公司在一个网段中，则子网掩码应设为（）。

A、255.255.255.0B、255.255.255.128C、255.255.255.192D、255.255.255.22412：B类地址的缺省掩码是（）。

ccna章节与期末答案

第一章：正确答案：2.4.5解析：由于不需要使用网络设备和专用服务器，对等网络易于创建，复杂性更低，且成本更少。

而且对等网络也没有集中管理。

这种网络安全性更低，不可扩展，而且那些同时充当客户端和服务器的设备可能性能更差正确答案：1解析：正确答案： 3.5解析：选择网络介质的条件包括：所选介质可以成功传送信号的距离、要安装所选介质的环境、必须传输的数据量和速度以及介质和安装的成本。

正确答案：3和4解析：终端设备上的应用程序可以生成数据，更改数据内容并且负责启动封装过程。

正确答案：1和4解析：终端设备会发出通过网络传输的数据。

中间设备会在链路发生故障时通过备用路径传输数据，并且会过滤数据传输以增强安全性。

网络介质提供网络消息的传输通道。

正确答案：4解析：外联网是公司外部的人或企业合作伙伴访问数据的网络区域。

内部网只描述通常仅供内部人员访问的网络区域。

当设备连接到有线网络时，有线 LAN 会受 BYOD（自带设备）影响。

使用大学无线 LAN 的设备多为平板电脑和智能手机。

大学生主要使用无线 WAN 来访问他们的手机运营商网络。

.正确答案：2解析：由于通过 Internet 可以联系在线供应商，所以家庭用户通过 Internet 进行网上购物。

内联网基本上是仅供内部使用的局域网。

外联网是外部合作伙伴访问组织内部特定资源的网络。

家庭用户并不一定使用 LAN 来访问 Internet。

例如，PC 可以通过调制解调器直接连接到 ISP。

正确答案：1解析：内部网这个术语用于表示一个组织的私有局域网和广域网连接。

内部网的设计旨在仅允许该组织的成员、员工或其他获得授权的人员进行访问。

正确答案：2和4解析：电缆和 DSL 均能实现高带宽、始终联网，并提供到主机计算机或 LAN 的以太网连接。

10正确答案：2和3解析：移动电话连接需要使用移动电话网络。

卫星连接通常用于家庭或企业外部不便使用物理布线的位置。

11正确答案：2解析：当对网络资源的请求超出了可用容量时，网络就会变得拥堵。

CCNA考试题

CCNA考试题一、选择题（每题5分）1、具有第 3 层功能的以太网交换机有哪两项关键功能？（选择两项。

）（）A、第 3 层路由功能B、网络地址转换(NA T)C、与远程网络和设备建立远程访问连接D、广播流量管理和组播流量管理E、采用边界网关协议(BGP) 进行自治系统(AS) 间路由2、第 2 层以太网交换机有哪三项功能？（选择三项。

）（）A、防止广播B、增大每名用户可用的带宽C、减小冲突域的大小D、在网段间隔离流量E、在不同的网络间路由流量F、减少广播域的数量3、分层网络设计模型中的哪一层称为互连网络的高速主干层，其中高可用性和冗余性是该层的关键？（）A、接入层B、分布层C、网络层D、核心层E、工作组层F、 W AN 层4、分层网络设计模型中的哪一层提供了将设备接入网络的途径并控制允许那些设备通过网络进行通信？（）A、应用层B、接入层C、分布层D、网络层E、核心层5、在处于不同的VLAN 中的设备间配置通信需要使用OSI 模型中的哪个层？（）A、第 1 层B、第 3 层C、第 4 层D、第 5 层6、推荐同时在核心层和分布层采用哪种分层设计特征以在发生路由故障时保护网络？（）A、交换B、冗余C、聚合D、访问列表7、为支持客户端关联过程，802.11 标准中指定了哪两种身份验证方法？（选择两项。

）（）A、轻型可扩展身份验证协议(EAP)B、共享密钥C、高级加密标准(AES)D、临时密钥完整性协议(TKIP)E、开放式身份验证8、传统路由与单臂路由器有何区别？（）A、传统路由只能使用单个交换机接口。

单臂路由器可使用多个交换机接口。

（）B、单臂路由器使用子接口将多个逻辑网络连接到单个路由器端口。

传统路由在每个逻辑网络中使用一个端口。

C、传统路由使用路由协议来向其它路由器更新路由。

单臂路由器仅将数据路由到直连网络。

D、单臂路由器不提供多个连接，因此消除了使用STP的需要。

传统路由使用通向路由器的多条路径，因此需要STP。

CCNA期末测试多选题

CCNA期末测试多选题多选题：1、对于这样一个地址,192.168.19.255/20,下列说法正确的是: （）(A) 这是一个广播地址(B) 这是一个网络地址(C) 这是一个私有地址(D) 地址在192.168.19.0网段上(E) 地址在192.168.16.0网段上(F) 这是一个公有地址答案：CE2、下面有关NAT叙述正确的是（）(A) NAT是英文“地址转换”的缩写，又称地址翻译(B) NAT用来实现私有地址与公用网络地址之间的转换(C) 当内部网络的主机访问外部网络的时候，一定不需要NAT(D) 地址转换的提出为解决IP地址紧张的问题提供了一个有效途径答案：ABD3、关于VLAN下面说法正确的是（）(A) 隔离广播域(B) 相互间通信要通过路由器(C) 可以限制网上的计算机互相访问的权限(D) 只能在同一个物理网络上的主机进行逻辑分组答案:ABC4、下面对路由器的描述正确的是（交换机指二层交换机）（）(A) 相对于交换机和网桥来说，路由器具有更加复杂的功能(B) 相对于交换机和网桥来说，路由器具有更低的延迟(C) 相对于交换机和网桥来说，路由器可以提供更大的带宽和数据转发功能(D) 路由器可以实现不同子网之间的通信，交换机和网桥不能(E) 路由器可以实现虚拟局域网之间的通信，交换机和网桥不能答案:ADE5、关于IP报文头的TTL字段，以下说法正确的有（）（多选）(A) TTL的最大可能值是65535(B) 在正常情况下，路由器不应该从接口收到TTL=0的报文(C) TTL主要是为了防止IP报文在网络中的循环转发，浪费网络带宽(D) IP报文每经过一个网络设备，包括Hub、LAN SWITCH和路由器，TTL值都会被减去一定的数值答案:BC6、VLAN的划分方法有（多选）（）(A) 基于设备端口(B) 协议(C) MAC(D) 物理地址答案:ABCD7、路由项10.0.24.0/21由哪几条子网路由聚合而来（）(A) 10.0.0.25/16(B) 10.0.0.23/16(C) 10.0.0.26/16(D) 10.0.0.22/16答案:AC8、在OSPF中，以下（）是两台路由器成为邻居关系的必要条件。

CCNA2期末测试题

1请参见图示。

对于发往192.168.2.0 的数据包，R2 会采取什么操作？它会丢弃数据包。

它会通过S0/0/0 接口转发数据包。

它会通过Fa0/0 接口转发数据包。

它会将数据包转发给R1。

2请参见图示。

R1 会使用哪一总结地址来向R2 通告其网络？3请参见图示。

尽管R2 已配置正确，但主机A 还是无法访问Internet。

可以在R1 上配置哪两条可让主机A 访问Internet 的静态路由？（选择两项。

）ip route .0 0.0.0.0 Fa0/0ip route .0 0.0.0.0 Fa0/1ip routeip routeip route 209.165.202.0 255.255.255.0 .14请参见图示。

网络管理员已按图示配置了R1，并且所有接口都运作正常。

但从R1 ping 172.16.1.1 时失败。

造成此问题的原因可能是什么？R1 上的串行接口配置有误。

默认路由配置有误。

必须在R1 上发出default-information originate命令。

必须在R1 上禁用自动总结。

5请参见图示。

所有接口都已编址，并且运行正常。

网络管理员在主机A 上运行了tracert命令。

得到这种输出的原因可能是什么？（选择两项。

）主机A 缺少网关或配置不正确。

主机B 缺少网关或配置不正确。

R1 的路由表中缺少192.168.1.0/24 的条目。

R2 的路由表中缺少192.168.1.0/24 的条目。

R1 的路由表中缺少192.168.2.0/24 的条目。

R2 的路由表中缺少192.168.2.0/24 的条目。

6请参见图示。

从主机A 到主机B 的ping 成功，但从主机A ping 在Internet 上正常运行的主机却失败了。

此问题的原因是什么？R1 的快速以太网接口被禁用。

其中一条默认路由配置有误。

未在这两台路由器上配置路由协议。

主机A 上尚未配置默认网关。

7 网络管理员使用RIP 路由协议在一个自治系统内实施路由。

CCNA期末考试题及答案试卷A(仅供参考)

1.下列有关网络层编址的陈述中哪三项是正确的?（选择三项。

）网络层编址使用分层式结构。

使用长度为48 位的地址。

以太网交换机可以使用它来作出转发决定。

它不支持广播。

其使用的编址方法可以识别地址的网络部分。

网络层编址可以区分每台主机。

2请参见图示。

网络中的所有设备均使用默认配置。

此拓扑中存在多少个广播域？3579113请参见图示。

主机B 已断电。

交换机的MAC 表将发生什么变化？MAC 表不会受影响。

交换机会在Fa0/19 上删除MAC 地址。

交换机会保留MAC 地址，直到主机B 再次通电。

交换机将通过为端口Fa0/19 分配地址FFF.FFFF.FFFF 来重建MAC表。

4.请参见图示。

为了使此网络中的主机接入Internet，路由器RT_A 需要提供哪种功能？地址转换DHCP 服务ftpWeb 服务器5.哪三个地址属于私有IP 地址？（选择三项。

）10.0.0.1127.0.0.1150.0.0.1172.16.0.1192.168.0.1200.100.50.16请参见图示。

电缆1 和电缆2 分别按照特定的物理层要求接线。

表中按编号列出了每个网段以及该网段中用来连接网络组件的电缆。

哪三个网段安装的电缆是正确的？（选择三项。

）网段1网段2网段3网段4网段5网段67.OSI 模型的哪两项功能在第2 层实现？（选择两项）物理编址编码路由布线介质访问控制8.请参见图示。

网络管理员想通过Modem1 从PC1 远程访问路由器的CLI。

要实现此访问，应将路由器的哪一个端口连接到Modem2？控制台端口以太网端口辅助端口串行端口9请参见图示。

某学生对5e 类电缆两端的接线方法如图所示。

结果是什么？（选择两项）电缆无法使用，必须重新接线。

该电缆适合作为全反电缆使用。

该电缆适合作为快速以太网交叉电缆使用。

该电缆适合作为千兆以太网直通电缆使用。

该电缆适合在支持Auto-MDIX 的两台100 Mbps 交换机之间使用。

CCNA2 final期末考试答案A

1.A technician configures the Fa0/0 interface on a router with ip address 192.168.3.5 255.255.255.252. What additional comma issued by the technician to activate the interface to forward traffic?Router(config-if)# exitRouter(config-if)# no shutdownRouter(config-if)# clock rateRouter# copy running-config startup-config2Refer to the exhibit. A technician has configured the interfaces on the Router, but upon inspection discovers that interface FastEthernet0/1 is not functioning. Which action will most likely correct the problem with FastEthernet0/1?A clock rate should be added to the interface configuration.The subnet mask should be added to the interface configuration.An interface description needs to be added to the interface configuration.The no shutdown command needs to be added to the interface configuration.3Refer to the exhibit. A router interface is configured with the command ip address 172.16.3.31 255.255.192.0. Which set o values would allow a computer that is connected to the router interface to communicate with remote networks?A: 172.16.3.254B: 255.255.192.0C: 172.16.3.31A: 172.16.3.31B: 255.255.192.0C: 172.16.3.255A: 172.16.3.254B: 255.255.255.0C: 172.16.3.31A: 172.16.3.31B: 255.255.255.0C: 172.16.3.14Refer to the exhibit. On the basis of the show running-config output, which option correctly reflects the routes that will be l routing table?ssss5Refer to the exhibit. PC1 is unable to access the Internet. What is the cause of the problem?An incorrect IP address is configured between the two routers.No static route is configured on Router2.A routing loop has occurred.No routing protocol is configured on either of the two routers.Refer to the exhibit. Which three statements are true of the routing table for Router1? (Choose three.)The route to network 172.16.0.0 has an AD of 156160.Network 192.168.0.16 can best be reached using FastEthernet0/0.The AD of EIGRP routes has been manually changed to a value other than the default value.Router1 is running both the EIGRP and OSPF routing process.Network 172.17.0.0 can only be reached using a default route.No default route has been configured.7Refer to the exhibit. The network has three connected routers: R1, R2, and R3. The routes of all three routers are displaye are operational and pings are not blocked on this network.Which ping will fail?from R1 to 172.16.1.1from R1 to 192.168.3.1from R2 to 192.168.1.1from R2 to 192.168.3.18Refer to the exhibit. A network administrator has configured OSPF using the following command:network 192.168.1.32 0.0.0.31 area 0Which router interface will participate in OSPF?FastEthernet0/0FastEthernet0/1Serial0/0/0Serial0/0/19Refer to the exhibit. The hosts on the R1 LAN are unable to access the Internet. What is incorrectly configured?the IP address of the Fa0/0 interface at R1the IP address of the S0/0/1 interface at R2the IP address of the S0/0/0 interface at R1the subnet mask of the S0/0/1 interface at R210Refer to the exhibit. Host A is having problems accessing server A. All routers have the same EIGRP configuration as rou What should be done so that host A can access server A?Add the command no auto-summary on all routers.Change the network statements to include a wildcard mask.Adjust the EIGRP hello timers to account for the network delay.Add the command eigrp log-neighbor-changes on all routers.Which feature of RIPv2 enables it to function as a classless routing protocol?Subnet masks are included in routing updates.Routing updates are triggered by topology changes.Next-hop addresses are included in routing updates.Multicast addresses are used to send routing updates.12A network administrator must use the subnet 172.16.128.0/18 to create 6 additional subnets each containing up to 2000 hLANs. Which subnet mask should the administrator use to create the new subnets?255.255.224.0255.255.240.0255.255.248.0255.255.252.013 A network administrator is in charge of two separate networks that share a single building. What device will be required totwo networks and add a common connection to the Internet that can be shared?hubrouteraccess pointEthernet switch14Refer to the exhibit. What needs to be done to allow these two routers to connect successfully?Add a clock rate to S0/0/0 on R1.Add an interface description to S0/0/1 on R2.Change the serial interface on R2 to S0/0/0 so that it matches R1.Change the IP address of S0/0/1 on R2 so that it is in the same subnet as R1.15In which situation would a default static route be recommended?when connecting an edge router to the Internetwhen variable length subnet masking is in effectwhen there is more than one valid route for a destination networkwhen a destination network has a larger mask than any routes in the routing tableRefer to the exhibit. A network engineer has run the show version command on R3. Upon rebooting, R3 does not load th configuration settings.What could be the cause of this problem?There is insufficient NVRAM.There is insufficient flash memory.The configuration register is not configured with the default setting.The system image file is not located in NVRAM.17Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this?The IP address of host A is incorrect.The default gateway of host A is incorrect.The Fa0/1 interfaces of the two routers are configured for different subnets.The subnet mask for the Fa0/0 interface of R1 is incorrect.18Refer to the exhibit. R1 and R2 are adjacent routers both running RIP. All interfaces on both routers are correctly configur operational. Both routers are configured to include all connected interfaces in routing updates. R2 is not showing any rout the routing table. What is the likely cause?The adjacent interfaces are passive.The distance of 120 exceeds 15 hops.R2 will not accept version 1 updates from R1.19W hich two technologies can be used in distance vector routing protocols to prevent routing loops? (Choose two.)authenticationlink-state advertisementshold-down timersSpanning Tree Protocolsplit horizon20Which prompt is used to allow a user to change the IP address of an interface on a router?Router>Router#Router(config)#Router(config-if)#Refer to the exhibit. A network administrator adds this command to router R1: ip route 192.168.2.0 255.255.255.0 S0/0/0 result of adding this command?This route is automatically propagated throughout the network.The traffic for network 172.16.1.0 is forwarded to network 192.168.2.0.A static route is established.The traffic for all Class C networks is forwarded to 172.16.1.2.22Refer to the exhibit. What information can be determined from the displayed output?EIGRP packets are waiting to be sent to the neighbors.The adjacencies between the routers are yet to be established.The IP address 192.168.10.10 is configured at serial interface S0/0/1 of router R2.Router R2 is receiving hello packets from a neighbor with the IP address 192.168.10.10 via the R2 S0/0/1 interface.23Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this router entering a password?The login command was not entered on the cons ole line.The enable password should be an enable secret password.No username and password combination has been configured.Console connections cannot be configured to require users to provide passwords.24W hich of the following are primary functions of a router? (Choose two.)packet switchingmicrosegmentationdomain name resolutionpath selectionflow control25Because of a topology change, the next hop IP address in the current static route must be reconfigured. How can a static altered to accommodate a topology change?Keep the existing static route and configure a new static route with the correct next hop IP address.Negate the existing static route and configure a new static route with the correct next hop IP address.Do nothing. The existing static route will automatically update the next hop entry with the new IP address.Keep the existing static route, reload the router, and configure a new static route with the correct next hop IP addresRefer to the exhibit. All routers are configured with no auto-summary. All routers have a default route via their Serial0/1 Router B receives a packet with a destination of 10.16.1.98. What path will the packet take?B-EB-E-D-AB-E-D-A then loop A-D-A until the TTL expiresB will immediately drop the packet.There is insufficient information to answer the question.27Refer to the exhibit. A network administrator is investigating why data packets with destination addresses of 172.16.10.10 192.168.10.100 are being dropped instead of being forwarded via the static route as expected. After confirming that the ip command has been applied on all routers in the network, what other action should the administrator take to ensure that da these addresses are forwarded via the static route?Check that all routers are configured with the same autonomous system number.Issue the no auto-summary command within the EIGRP configuration of all routers.Issue the no passive-interface command within the EIGRP configuration of all routers.Configure the static route to point to the next hop address instead of the outbound interface.28If a router is booting with its default configuration register setting and its NVRAM lacks boot system commands, from whe router try to load the IOS image first?ROMRAMNVRAMflashTFTP server29T wo routers need to be configured within a single OSPF area. Which two components need to be configured on both rout this? (Choose two.)the same process IDthe same area IDnetwork addresses and wildcard masksthe same router IDthe same loop back address30Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choos10.0.0.0/864.100.0.0/16128.107.0.0/16172.16.40.0/24192.168.1.0/24192.168.2.0/24Which candidate route has the longest match for a packet with a destination address of 10.30.16.48?10.30.0.0/1610.30.15.0/2310.30.16.0/2410.30.16.32/2710.30.16.32/3032W hich three statements are true regarding the encapsulation and de-encapsulation of packets when traveling through a r (Choose three.)The router modifies the TTL field, decrementing it by one.The router changes the source IP to the IP of the exit interface.The router maintains the same source and destination IP.T he router changes the source physical address to the physical address of the exit interface.The router changes the destination IP to the IP of the exit interface.The router sends the packet out all other interfaces, besides the one it entered the router on.33Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routers are establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem?Check if the interfaces of the routers are enabled.Check the hello and dead intervals between the routers.Check the process ID of both routers.Check if CDP is enabled on all the routers.34W hich mechanism helps to avoid routing loops by advertising a metric of infinity?route poisoningsplit horizonhold-down timertriggered updates35Refer to the exhibit. A device is required to complete the connection between router R1 and the WAN. Which tw o devices for this? (Choose two.)a CSU/DSU devicea modeman Ethernet switcha huba bridge36Why is fast convergence desirable in networks that use dynamic routing protocols?Hosts are unable to access their gateway until the network is converged.Routers will not allow packets to be forwarded until the network is converged.Routers may make incorrect forwarding decisions until the network has converged.Routers will not allow configuration changes to be made until the network has converged.37Refer to the exhibit. R1 is configured properly for a single area OSPF, and R2 has been recently installed in the network.commands is required to configure a single area OSPF for the networks that are connected to R2?R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config)# router ospf 2R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 1R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.0.0.0 0.0.0.3 area 138Refer to the exhibit. Which path will traffic from the 172.16.1.0/24 network take to get to the 10.0.0.0/24 network?ADCABCIt will load balance the traffic between ADC and ABCIt will send the traffic via ABC, and will use ADC as a backup path only when ABC fails.39W hat are two ways that a router can learn of the paths to destination networks? (Choose two.)updates from other routersDHCP information broadcastsmanual configuration of routesARP requests from connected routersinspection of the destination IP address in data packetsupdates from the SMTP management information base40Refer to the exhibit. The network administrator has run the following command on R1.R1(config)# ip route 192.168.2.0 255.255.255.0 172.16.1.2What is the result of running this command?Traffic for network 192.168.2.0 is forwarded to 172.16.1.2.This route is automatically propagated throughout the entire network.Traffic for all networks is forwarded to 172.16.1.2.The command invokes a dynamic routing protocol for 192.168.2.0.Refer to the exhibit. What is the meaning of the highlighted value 120?It is the metric that is calculated by the routing protocol.It is the value that is used by the DUAL algorithm to determine the bandwidth for the link.It is the administrative distance of the routing protocol.It is the hold-down time, measured in seconds, before the next update.42Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes down. Which statement is tru how the routers in this topology will respond to this event?Router4 will learn about the failed route 30 seconds later in the next periodic update.Split horizon will prevent Router4 from fowarding packets to the 10.0.0.0 network until the holddown timer expires.Router5 immediately flushes the unreachable route from its routing table.Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0.43Refer to the exhibit. Which combination of IP address and subnet mask can be used on the serial interface of Router2 in o interface in the same network as the serial interface of Router1?IP 172.16.0.18, subnet mask 255.255.255.0IP 172.16.32.15, subnet mask 255.255.255.240IP 172.16.0.18, subnet mask 255.255.255.252IP 172.16.32.18, subnet mask 255.255.255.25244W hich statement is true about the RIPv1 protocol?It is a link-state routing protocol.It excludes subnet information from the routing updates.It uses the DUAL algorithm to insert backup routes into the topology table.It uses classless routing as the default method on the router.45Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2?192.168.1.0/24192.168.0.0/24192.168.0.0/22192.168.1.0/22Which two statements are true for link-state routing protocols? (Choose two.)Routers that run a link-state protocol can establish a complete topology of the network.Routers in a multipoint network that run a link-state protocol can exchange routing tables.Routers use only hop count for routing decisions.T he shortest path first algorithm is used.Split horizon is used to avoid routing loops.47A router learns about network 192.168.10.128/27 from multiple sources. Which option represen ts the best route and will berouting table?S 192.168.10.128/27 [1/0] via 192.168.10.226R 192.168.10.128/27 [120/2] via 192.168.10.226, 00:00:14, Serial0/0/0O 192.168.10.128/27 [110/1563] via 192.168.10.226, 00:00:09, Serial0/0/0D 192.168.10.128/27 [90/21026560] via 192.168.10.226, 00:00:16, Serial0/0/048Refer to the exhibit. When all of the commands that are shown in the exhibit are entered at the correct router prompt, wha of the router?nameciscorouterhostname49W hich statement is true about the metrics used by routing protocols?A metric is a value used by a particular routing protocol to compare paths to remote networks.A common metric is used by all routing protocols.The metric with the highest value is installed in the routing table.The router may use only one parameter at a time to calculate the metric.50Which two statements are true about the EIGRP successor route? (Choose two.)It is saved in the topology table for use if the primary route fails.It may be backed up by a feasible successor route.It is used by EIGRP to forward traffic to the destination.It is flagged as active in the routing table.After the discovery process has occurred, the successor route is stored in the neighbor table.Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as shown in the output of the show ip rip databa However, upon running the show ip route command, the network administrator sees that the router has installed a differe 192.168.6.0 network learned via EIGRP. What could be the reason for the missing RIP route?Compared to RIP, EIGRP has a lower administrative distance.Compared to EIGRP, RIP has a higher metric value for the route.Compared to RIP, the EIGRP route has fewer hops.Compared to RIP, EIGRP has a faster update timer.52A network administrator is analyzing routing update behavior on a network that has both EIGRP and OSPF configured on Both protocols appear in the output of show ip protocols. However, only EIGRP internal routes appear in the routing tabstatement correctly explains the scenario?The OSPF protocol has a higher cost than EIGRP.The EIGRP protocol has a lower metric than OSPF.The EIGRP protocol was configured first on the router.The EIGRP protocol has a lower administrative distance than OSPF.。

CCNA第二学期考试答案

以下是针对您未获得满分的试题给出的反馈。

某些交互式试题可能不显示您的答案。

分项分数：1与固定配置的交换机相比，模块化交换机具有哪两个优点？（请选择两项。

）正确响应您的响应每台交换机的成本更低可扩展性更高转发率更低需要的电源插座数目更少带宽聚合可以使用多个端口固定配置交换机价格较低，但是它具有指定数量的端口且不能添加端口。

它们提供的高速端口通常比较少。

为了在包含固定配置交换机的网络上扩展交换，需要购买更多的交换机。

这增加了需要使用的电源插座数量。

模块化交换机只需要购买额外的线卡便可以扩展。

带宽聚合也更容易，因为机箱的背板可以为交换机端口线卡提供所需的带宽。

此试题参考以下领域的内容：Routing and Switching Essentials• 1.1.2 交换网络2思科无边界架构接入层的基本功能是什么？正确响应您的响应聚合第 2 层广播域聚合第 3 层路由边界为用户提供访问权提供高可用性思科无边界架构接入层的功能是为用户提供网络访问。

第 2 层广播域聚合、第 3 层路由边界聚合和高可用性是分布层的功能。

也有说答案是聚合第 3 层路由边界此试题参考以下领域的内容：Routing and Switching Essentials• 1.1.1 融合网络3思科无边界架构分布层的基本功能是什么？正确响应您的响应充当主干聚合所有园区块聚合第 3 层路由边界为用户提供访问权思科无边界架构的分布层的一项基本功能是在不同的VLAN 之间路由。

充当主干和聚合园区块是核心层的功能。

为用户提供访问是接入层的功能。

此试题参考以下领域的内容：Routing and Switching Essentials• 1.1.1 融合网络4若将大端口密度、容错和低价作为重要指标，应使用哪个交换机外形因素？正确响应您的响应固定配置交换机模块化交换机可配备机架的1U 交换机可堆叠式交换机堆叠式交换机可以使用特殊电缆实现互联，从而在交换机之间提供高带宽的吞吐量，并像单个大型交换机一样运行。

CCNA期末考试答案(网络安全技术练习题)

1. 半连接攻击属于（）A．溢出攻击 B.嗅探攻击 C. 注入攻击 D.拒绝服务攻击2. TCP三次握手中用到的标志位是（）A. FINB. SYNC. RSTD. PSH3. 下列关于对称加密算法和非对称加密算法的说法中正确的是（）A.对称加密速度较慢B.对称加密可以实现数据的不可否认性C.非对称加密速度较慢D.非对称加密的密文是紧凑的4 以下不支持认证功能的路由协议是（）A. EIGRPB. Ripv1C.ospfD. Ripv25. 以下哪一项不属于保护路由器的有效方法（）A.开启日志服务并建立日志服务器B. 部署NTP服务器实现时钟同步C.关闭路由器上的CDP服务D. 启用端口安全6.以下关于SSH的说法正确的是（）A.SSH采用对称加密算法B.SSH未对数据加密C.SSH采用非对称加密算法D.SSH一般用于内网发起的管理行为7. AAA不包含哪一层含义（）A.认证B.过滤C.授权D.记账8.以下哪一项是思科的私有协议（）A.radiusB.802.1qC.tacacs+D.ipsec9.通过访问控制列表防范分片攻击需要在语句后加关键字（）A.establishedB.fragmentC.logD.reflect10.以下哪一项是基于异常的IDS监测模式的缺点（）A.不能抵御新型攻击B.特征库更新速度制约使用效果C.不会错报D.容易错报漏报11. 以下关于IDS与IPS说法正确的是( )A. IDS一般部署在网络出口主干链路上B.IDS能够阻断发现的攻击行为C. IPS一般根据特征库来检测攻击行为D.IPS不能阻断发现的攻击行为12. 以下不能起到防火墙作用的技术是（）A.IDSB.ACLC.NATD.代理服务器13.以下关于MD5的说法正确的是( )A.md5是一种加密算法B.md5用于保障数据的机密性C.md5是可逆的D.md5用于保障数据的完整性14. 为恢复路由器登录密码，需把寄存器值改为（）。

CCNA第二学期期末考试

1关于数据包通过路由器传输时的封装和解封的叙述,下列哪三项是正确的？（选择三项。

) 路由器修改 TTL 字段，将其值减 1.路由器将源 IP 更改为送出接口的 IP。

路由器保持相同的源 IP 和目的 IP。

路由器将源物理地址更改为送出接口的物理地址。

路由器将目的 IP 更改为送出接口的 IP。

路由器会从所有接口将数据包转发出去,包括路由器接收数据包时使用的那个接口.Option 1, Option 3， and Option 4 are correct。

2请参见图示。

当数据包发往哪两个网络时需要路由器执行递归查找？（选择两项。

)10。

0。

0.0/864。

100.0。

0/16128。

107.0。

0/16172。

16.40.0/24192.168.1。

0/24192.168.2.0/24Option 1 and Option 6 are correct.3对于为防止路由环路而通过毒性反转实现的水平分割方法,哪两项叙述正确？（选择两项。

) 所有 Cisco IOS 都会默认启用此方法。

会将一个表示无穷大度量的值分配给路由以将其毒化。

将毒化路由更新发回该更新的发送接口。

指示路由器将可能会影响路由的更改保持一段特定的时间。

限制数据包在被丢弃之前能够在网络中传输的跳数。

Option 2 and Option 3 are correct.4网络管理员在所示网络图中的路由器 B 和 C 上启用了 RIP。

什么命令可防止向路由器 A 发送 RIP 更新?A(config)# router ripA（config-router)# passive—interface S0/0B(config）＃ router ripB（config—router）＃ network 192.168。

25.48B（config-router)# network 192。

168.25.64A(config）＃ router ripA(config—router)＃ no network 192。

CCNA期末考试复习题(1)

CCNA期末考试复习题一、选择题1 、图示的网络中有多少个冲突域？A 1B 2C 3D 6E 72、如图所示网络，交换机都是默认配置。

主机A需要和主机D通信，但是主机A没有默认网关的MAC地址。

哪些主机将收到主机A发出的ARP请求？A 只有主机DB 只有路由器R1C 只有主机B和CD 只有主机B，C和DE 只有主机B，C和路由器R13、如图所示，主机A属于哪个子网？A 10.197.0.0B 10.192.0.0C 10.197.184.0D 10.197.187.0E 10.197.187.1684、248表示为二进制形式是：A 11101000B 11110100C 11111000D 111110105、10BASE-T指哪种线缆？A 10Mbit/s传输速度，基带信号，线缆长度500M，同轴线B 10Mbit/s传输速度，宽带信号，线缆长度100M，同轴线C 10Mbit/s传输速度，基带信号，线缆长度100M，双绞线D 10Gbit/s传输速度，宽带信号，线缆长度500M，双绞线6、如图所示，网络管理员希望创建一个子网用于两个路由器点对点连接。

哪个子网掩码可以给点对点连接提供足够的地址，且浪费又最少？A 255.255.255.192B 255.255.255.224C 255.255.255.240D 255.255.255.248E 255.255.255.2527、如图所示，主机A希望发送一个消息给主机B。

请将下列步骤排列为正确的顺序，使得消息能够发送出去。

A——添加网络层地址B——发送比特C——创建应用层数据D——添加数据链路层地址A B—A—D—CB D—A—C—BC A—D—C—BD C—A—D—BE C—D—A—BF C—B—A—D8、一个C类网络192.168.35.0使用/28的掩码划分子网，可用子网个数及每子网的可用主机数分别是多少？A 6 子网/64主机B 14 子网/32主机C 14子网/14主机D 30子网/64主机9、哪种协议用来消灭交换环路？A TCPB RIPC STPD IGRPE IP10、因为无法ping通本地路由器，技术人员决定查看一下路由器。

CCNA 2 Final Exam Answers V3.1

1. What are two possible reasons a router would not load a valid IOS from flash? (Choose two.)The configuration register is set to 0×2142.The first boot system command executed in the startup configuration file is boot system rom.The configuration register is set to 0×2100.The boot field is set to the hexadecimal number 2.The startup configuration file is missing or corrupt.2. What are two recommended uses of login banners? (Choose two.)to display security warning messagesto welcome any user to the routerto warn people about misusing privileged EXEC modeto identify circuits and other devices connected to the routerto announce a scheduled system shutdown3.Router A and Router B have been correctly configured to use RIP as a dynamic routing protocol and all intefaces on Router A and Router B are reporting "interface is up, line protocol is up" status. RIP is then configured onRouter C using the following commands:RouterC(config)# router ripRouterC(config-router)# network 192.168.4.0RouterC(config-router)# network 172.16.0.0If no additional routing is configured on Router A, Router B, and Router C, what will be the result?Networks 192.168.12.0/24, 192.168.4.0/24, and 172.16.0.0/16 will be unreachable from Router A.Router A will have no knowledge of network 192.168.12.0/24, but will have routes to networks 192.168.4.0/24 and 172.16.0.0/16.All networks shown in the graphic will be reachable by Router A, Router B, and Router C.Networks 192.168.4.0/24 and 172.16.0.0/16 will be unreachable from Router A and Router B.4. What are the primary functions of a router? (Choose two.) determine the best path for packetsprevent collisions on the network LANregulate flow control between sender and receiverprovide domain name resolutionforward packets to the appropriate interface5. What are some reasons to change the configuration register setting? (Choose two.)to force the system to ignore the configuration file stored in NVRAM to monitor password changesto change the POST sequenceto force the router to boot the IOS from NVRAMto force the system into ROM monitor mode6. A network administrator issues the erase startup-config command on a configured router with the configuration register set to 0×2102 and observes the following output:Erasing the nvram filesystem will remove all files! Continue? [Confirm] [OK]Erase of nvram: completeIf the router unexpectedly loses power after this sequence, what will occur when power is restored?The router will enter ROM monitor mode upon completion of the power-on self test (POST).The router will load the last known valid configuration file.The router will enter Rx-boot mode.The router will prompt the user to enter setup mode or to continue without entering setup mode.7. Why are routed protocols important to networking? (Choose two.) Routed protocols detect collisions and fragments.Routers use routed protocols to calculate the best path to a destination. Routed protocols transport data across the network.The fields and formats used within a packet are defined by routed protocols.Routed protocols are used to configure the metrics used by routing protocols.8. The main router of XYZ company has enough flash and RAM to store multiple IOS images. An administrator wants to upload a second IOS image from a TFTP server to the flash of the router. Which method will accomplish this task?Paste the IOS filename to the command line of the router while in global configuration mode. Press enter. Then issue the copy tftp flash command.Use the setup utility to load the new image to flash.Copy the IOS image file from a TFTP server using the command copy filenameip address flash .Copy the IOS image file from a TFTP server using the command copy tftp flash. When prompted, provide the IP address or name of the TFTP server and the IOS image filename.9.A network administrator has a console connection to the Fremantle router. Pings to Melville are successful, but pings to Cottesloe and Nedlands fail. What could be a first step in troubleshooting the problem?Use an extended ping from Fremantle to each router in the network.Use the show interfaces command from a Telnet session on Melville to check the connection to Cottesloe.Use the traceroute command to discover exactly which link in the network is down.Use the show cdp neighbors detail command from Fremantle to gather information about all Cisco routers in the network.10.Refer to the exhibit. The new security policy for the company allows all IP traffic from the Engineering LAN to the Internet while only web traffic from the Marketing LAN is allowed to the Internet. Which ACL can be applied in the outbound direction of Serial 0/1 on the Marketing router to implement the new security policy?access-list 197 permit ip 192.0.2.0 0.0.0.255 anyaccess-list 197 permit ip 198.18.112.0 0.0.0.255 any eq wwwaccess-list 165 permit ip 192.0.2.0 0.0.0.255 anyaccess-list 165 permit tcp 198.18.112.0 0.0.0.255 any eq wwwaccess-list 165 permit ip any anyaccess-list 137 permit ip 192.0.2.0 0.0.0.255 anyaccess-list 137 permit tcp 198.18.112.0 0.0.0.255 any eq wwwaccess-list 89 permit 192.0.2.0 0.0.0.255 anyaccess-list 89 permit tcp 198.18.112.0 0.0.0.255 any eq www11.Hosts from the Limerick LAN are not allowed access to the Shannon LAN but should be able to access the Internet. Which set of commands will create a standard ACL that will apply to traffic on the Shannon router interface Fa0/0 implementing this security?access-list 42 deny 172.19.123.0 0.0.0.255 192.0.2.0 0.0.0.255 access-list 42 permit anyaccess-list 56 deny 172.19.123.0 0.0.0.255access-list 56 permit anyaccess-list 61 deny 172.19.123.0 0.0.0.0access-list 61 permit anyaccess-list 87 deny ip any 192.0.2.0 0.0.0.255access-list 87 permit ip any12. Which of the following commands will correctly configure an extended ACL? (Choose two).Router(config)# access-list 18 permit tcp host 192.168.73.3 eq 25Router(config)# access-list 102 permit tcp 10.43.0.0 0.0.255.255 any eq 80Router(config)# access-list 187 permit tcp host 192.168.42.34 172.29.0.0 0.0.255.255 eq 23Router(config)# access-list 99 permit host 10.217.32.3Router(config)# access-list 128 permit tcp host 192.168.100.31 eq 2313. What are the results of setting the boot field bits in the configuration register to "0000"? (Choose two.)The startup-config file will be ignored at bootup.The router will load the IOS from Flash.The router will enter ROM monitor mode upon reload.The router will enter boot ROM mode and have limited capabilities. The administrator can enter the b command to manually boot the IOS.14.Refer to the exhibit. Router D interface S0 on has gone down. What is the maximum time that will elapse before Router A learns that network 168.58.14.0 is down?5 seconds13 seconds17 seconds25 seconds30 seconds77 seconds15. During initial router bootup the following line appears: "NVRAM invalid, possibly due to write erase."What are two possible reasons for this result? (Choose two.)The startup-config file was not saved to RAM before reboot.The IOS has been erased.The router has not been configured.The startup-config file cannot be located.The router will not enter initial configuration dialog.16.The Suffolk router is directly connected to the networks shown in the graphic and has a default route that points to the Richmond router. All interfaces are active and properly addressed. However, when the workstation on network 172.29.5.0/24 sends a packet to destination address 172.29.198.5, it is discarded by the Suffolk router. What can be a reason for this result?The ip classless command is not enabled on the Richmond router.The route was ignored if the Richmond router did not include the 172.29.198.0/24 network in its routing updates.The Richmond router is in a different autonomous system than the Suffolk router.The ip subnet-zero command was not configured on the Suffolk router.The ip classless command is not enabled on the Suffolk router.17. access-list 199 deny tcp 178.15.0.0 0.0.255.255 any eq 23 access-list 199 permit ip any anyAssuming this ACL is correctly applied to a router interface, which statements describe traffic on the network? (Choose two.)All FTP traffic from network 178.15.0.0 will be permitted.All Telnet traffic destined for network 178.15.0.0 will be denied.Telnet and FTP will be permitted from all hosts on network 178.15.0.0 to any destination.Telnet will not be permitted from any hosts on network 178.15.0.0 to any destination.Telnet will not be permitted to any host on network 178.15.0.0 from any destination.18.What facts can be determined from the highlighted text shown in the exhibit? (Choose two.)A weak encryption was applied to all unencrypted passwords.The enable password is now more secure than the enable secret password.An MD5 hashing algorithm was used on all encrypted passwords.Any configured user EXEC mode or Telnet passwords will be encrypted in this configuration.The service password-encryption command was used to encrypt all passwords on the router including enable secret.19. What are three features of CDP? (Choose three.)provides information on directly connected devices that have CDP enabled tests Layer 2 connectivityenabled by default on each interfaceprovides a layer of securityused for debugging Layer 4 connectivity issues20. What information can be learned during the initial router bootup? (Choose two.)the configuration register valuethe number and types of interfaces installedthe router model and the amount of memory that is availablethe amount of memory required to load the IOS and configurationthe number of interfaces with connected cables21.What can be concluded from the output shown in the exhibit? (Choose three.)This is a standard IP access list.This is an extended IP access list.The keyword host is implied in the command line access-list 99 deny 10.213.177.76.The wildcard mask must be configured for this access list to function properly.Host 10.213.177.100 will be allowed access to the Serial0/1 interface.22. Which statements are true regarding setup mode? (Choose three.)Press Ctrl-z to terminate setup mode.Enter a question mark (?) for help at any point.Press Spacebar to accept the default settings.Use setup mode to enter complex protocol features.Press Enter to accept the default settings.Press Ctrl-c to abort configuration dialog.23.Refer to the graphic. Which series of commands will create static routes that will allow Router A and Router B to deliver packets destined for LAN A and LAN B, and direct all other traffic to the Internet?RouterA(config)# ip route 10.90.3.0 255.255.255.0 192.168.3.2RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1 RouterB(config)# ip route 0.0.0.0 0.0.0.0 s0/0RouterA(config)# ip route 10.90.3.0 255.255.255.0 192.168.3.2RouterA(config)# ip route 0.0.0.0 0.0.0.0 192.168.3.2RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1RouterA(config)# ip route 0.0.0.0 0.0.0.0 192.168.3.2RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1 RouterB(config)# ip route 172.20.20.4 255.255.255.252 s0/0RouterA(config)# ip route 0.0.0.0 0.0.0.0 192.168.3.2RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1 RouterB(config)# ip route 0.0.0.0 0.0.0.0 s0/024.Which devices can be used to convert the data from a WAN router at the customer site into a form acceptable for use by the WAN service provider? (Choose three.)Ethernet switchDTEmodemhubDCE deviceCSU/DSU25.What will occur when the following ACL is applied inbound to both FastEthernet interfaces of Router A in the graphic?access-list 125 permit tcp 192.168.2.0 0.0.0.255 10.90.3.0 0.0.0.255 eq 23access-list 125 permit tcp 10.90.3.0 0.0.0.255 192.168.2.0 0.0.0.255 eq 23access-list 125 permit tcp 192.168.2.0 0.0.0.255 any eq wwwWorkstations A and B will be able to Telnet to each other. WorkstationA will be allowed to access Web servers on the Internet, while WorkstationB will be denied Internet Web access.Workstations A and B will be able to Telnet to each other. All other traffic will be denied.The ACL will have no effect because it should be applied in the outbound direction on the FastEthernet interfaces.The ACL will deny all traffic because of the implied deny ip any any statement at the end of the ACL.26. Based on this partial output of the show ip route command, which routing protocol is configured on the router?R 172.16.3.0/24 [120/3] via 172.16.2.2, 00:00:27, Serial0/0RIPEIGRPOSPFIGPBGP27.Which of the following are correct statements verified by the router output shown in the graphic? (Choose two.)Layer 3 connectivity exists between BigCity and the devices in the Device ID column.Layer 2 connectivity exists between BigCity and the devices in the Device ID column.All devices shown in the Device ID column use the TCP/IP protocol suite.All devices shown in the Device ID column can be pinged from BigCity.All devices listed in the Device ID column are directly connected to BigCity.28. A network administrator must configure a FastEthernet interface with an IP address. The configuration must also identify the remote site to which the interface is connected. Which set of commands will meet these requirements?StPetersburg(config)# banner San Jose T1StPetersburg(config)# interface fa0/0StPetersburg(config-if)# ip address 172.26.155.5 255.255.255.252StPetersburg(config)# interface fa0/0StPetersburg(config-if)# ip address 172.26.155.5 netmask255.255.255.252StPetersburg(config-if)# description San Jose T1StPetersburg(config)# interface fa0/0StPetersburg(config-if)# ip address 172.26.155.5 255.255.255.252 StPetersburg(config-if)# banner remote site San Jose T1StPetersburg(config)# interface fa0/0StPetersburg(config-if)# ip address 172.26.155.5 255.255.255.252 StPetersburg(config-if)# description San Jose T129. What are the features of a serial interface on a router? (Choose two.) enabled by defaultassigned a unique MAC addressmust be configured as a DCE in lab and production environmentsmust be configured with the default clock rate of 56000may be administratively enabled by using the no shutdown commandmust be configured with a valid IP address and subnet mask in order to forward packets30. Assuming the following ACL is correctly applied to a router interface, what can be concluded about this set of commands? (Choose two.) Router(config)# access-list 165 deny tcp 192.28.115.0 0.0.0.255 172.20.0.0 0.0.255.255 eq 23Router(config)# access-list 165 permit ip any anyThis is a standard IP access list that denies network 192.28.115.0 Telnet access to the 172.20.0.0 network.All Telnet traffic destined for 172.20.0.0 from any network will be denied access.Network 192.28.115.0 is denied Telnet access to the 172.20.0.0 network. Network 172.20.0.0 is denied Telnet access to the 192.28.115.0 network.All FTP and HTTP traffic destined for 172.20.0.0 will be permitted access.31. Which two steps describe how to create a functional physical connection between a router console and a terminal? (Choose two.)Use a crossover cable to connect the terminal serial port to the router console port.Use a rollover cable to connect the terminal NIC to the router console port.Use an RJ-45 to DB-9 adapter on the terminal serial port to connect to the cable going to the router console.Use a transceiver to connect a straight-through cable to the router console port.Use a straight-through cable to connect the router console port to the terminal NIC.Use a rollover cable to connect from a terminal serial port to the router console port.32. What critical information about the status of the router can be found in the outputs of both the show interfaces and show protocols commands? (Choose two.)the Layer 3 address of each configured interfacethe routing protocol configured to forward updates out of each interface the operational status of each interfacetraffic statistics for each interfacewhether the interface is configured as a DTE or DCE33.The following access list has been created to prevent traffic from the 192.0.2.63 host on the Sales LAN from accessing servers and hosts on the Payroll LAN.access-list 26 deny host 192.0.2.63access-list 26 permit anyRefer to the exhibit. Which group of commands will properly place the access list so that only the host on the Sales LAN is denied access to the 172.29.7.0 network but all other traffic is permitted?Payroll(config)# interface fa0/0Payroll(config-if)# ip access-group 26 outPayroll(config)# interface fa0/1Payroll(config-if)# ip access-group 26 outSales(config)# interface fa0/1Sales(config-if)# ip access-group 26 inSales(config)# interface fa0/0Sales(config-if)# ip access-group 26 out34.Refer to the exhibit. Assuming default metrics are used and the networkis fully converged, which path will RIP use to send a packet from Router A to Router F?A, D, E, FA, B, D, E, FA, C, D, E, G, FA, B, D, E, G, F35.Refer to the graphic. Communication is needed between the LAN connected to the fa0/0 interface of the Kansas router and the fa0/0 interface of the Maine router. All hosts on those LANs also need connectivity to the Internet. Which commands will allow this communication? (Choose three).Kansas(config)# ip route 192.168.6.0 255.255.255.0 172.18.64.2Kansas(config)# ip route 192.168.6.0 255.255.255.0 s0/1Kansas(config)# ip route 0.0.0.0 0.0.0.0 s0/1Maine(config)# ip route 192.168.6.0 255.255.255.0 172.18.64.1Maine(config)# ip route 0.0.0.0 0.0.0.0 s0/1Maine(config)# ip route 172.16.32.0 255.255.255.0 172.18.64.236. Why are interface descriptions used in router configurations? (Choose three).to enable support personnel to easily identify networks and customers that may be affected by a possible interface issueto provide comments on the interface without affecting the router functionalityto display access warning messages before users enter the interface configuration modeto eliminate the need to use IP addresses when using the ping and telnet commandsto identify the purpose and location of the interface37.A network administrator has enabled RIP on routersB andC in the network diagram. Which of the following commands will prevent RIP updates from being sent to Router A?A(config)# router ripA(config-router)# passive-interface S0/0B(config)# router ripB(config-router)# network 192.168.25.48B(config-router)# network 192.168.25.64A(config)# router ripA(config-router)# no network 192.168.25.32B(config)# router ripB(config-router)# passive-interface S0/0A(config)# no router rip38. What could a Cisco support technician learn from the IOS filename c2600-d-mz.121-3? (Choose three.)the format of the filethe RAM memory requirements of the filethe version number of the filethe size of the filethe device platform of the file39.While planning an IOS upgrade, the administrator issues the show version command. Based on the output in the graphic, what is the current IOS boot location?RAMNVRAMFlashROM40. A new technician must add boot system commands to one of the department routers. Which available commands will the router return as output when the command shown below is entered? (Choose two.)Router(config)# boot system ?RAMNVRAMIOSIP AddressTFTPFLASH41. From the running-config, the following configuration entries are displayed:Router(config)# line vty 0 2Router(config-line)# password g8k33prRouter(config-line)# loginWhat can be interpreted from the exhibited configuration? (Choose two.)Three Telnet lines are available for remote access.Two Telnet lines are available for remote access.Future configuration of the remaining Telnet lines will require the password to be set to g8k33pr.To login to the remote device, g8k33pr will be used as the Telnet and secret password.Remote access to this local router will require a Telnet password of g8k33pr.42. Which router component stores the information that is displayed by the show running-config command?flashNVRAMRAMROM43. What are two characteristics of the support for Telnet within Cisco IOS software? (Choose two.)Up to five separate Telnet lines are supported by default in standard edition IOS files.For security purposes, Telnet sessions are required to be established from the privileged mode.A router can host simultaneous Telnet sessions.Once established, a Telnet session can remain operational regardless of network status.Telnet tests wireless connectivity and does not require a physical connection between devices to gain remote access.44. Which router components and operations are correctly described? (Choose two.)RAM – stores the ARP cacheNVRAM – store the operating systemROM – stores the backup IOSPOST – verifies the validity of the running-configFlash – executes diagnostics at bootupDRAM – loads the bootstrap45.Given the output shown in the exhibit, in what order and location will the router search for the IOS if no boot system commands are found in the startup-config file?ROM, Flash, TFTP serverFlash, NVRAM, RAMROM, TFTP server, FlashRAM, Flash, NVRAMFlash, TFTP server, ROM46. What can a network administrator do to recover from a lost router password?perform a reload or resettelnet from another router and issue the show running-config command to view the passwordboot the router to ROM monitor mode and configure the router to ignore NVRAM when it initializesboot the router to bootROM mode and enter the b command to load the IOS manually47.Neither router in the exhibit has a host table or DNS available. The interfaces and passwords have been correctly configured. Which of the following commands will initiate a Telnet session? (Choose two.)Tottenham# telnet OxfordTottenham> telnet 198.18.139.1Oxford# connect 198.18.139.0Oxford> connect TottenhamOxford# telnet TottenhamOxford# 198.18.139.248. If a PC does not have network connectivity to a router, which router port can be used to establish communication?consoleEthernetserialVTY。

CCNA第二学期期末练习题

1如图所示的网络在路由流量时存在问题，怀疑这可能是编址方案所造成。

该图中使用的编址方案存在什么问题？指定给Router1 的Ethernet0 接口的地址是该子网的广播地址。

在Router1 和Router2 之间的串行链路上配置的子网与指定给Router3 上Ethernet0 的子网有重叠。

Router1 的Serial0 接口与Router2 的Serial0 位于不同的子网。

指定给Router2 上Ethernet0 的子网与指定给Router3 上Ethernet0 的子网有重叠。

2 points for Option 22请参见图示。

网络管理员要将一个带有50 台主机的新子网添加至R3。

要保证新子网可获得足够地址，同时尽量减少地址浪费，应为其分配哪个子网地址？192.168.1.0/24192.168.1.48 /28192.168.1.32/27192.168.1.64/262 points for Option 43出现路由环路的两个原因是什么？（选择两项）收敛速度缓慢静态路由配置错误路由通过两种路由协议获知在同一台路由器上同时使用静态路由和动态路由连接到Internet 的路由器上缺少默认路由Option 1 and Option 2 are correct.4下列哪两项是路由器的功能？（选择两项。

）连接多个IP 网络。

通过使用第2 层地址控制数据流。

确定发送数据包的最佳路径。

管理VLAN 数据库。

扩大广播域。

Option 1 and Option 3 are correct.5哪三项是CDP 的特性？（选择三项。

）测试第2 层连通性提供安全层工作在OSI 第2 层和第3 层默认在每个接口上启用用于调试第4 层连通性问题提供关于已启用CDP 的直连设备的信息Option 1, Option 4, and Option 6 are correct.6下列有关路由器上的启动配置的说法，哪两项是正确的？（选择两项）路由器使用启动配置文件来启动POST。

CCNA2final期末考试答案A

ip address 192.168.3.5 255.255.255.252. What additional comma 1.A technician configures the Fa0/0 interface on a router with issued by the technician to activate the interface to forward traffic? Router(config-if)# exitRouter(config-if)# no shutdownRouter(config-if)# clock rateRouter# copy running-config startup-config2Refer to the exhibit. A technician has configured the interfaces on the Router, but upon inspection discovers that inte FastEthernet0/1 is not functioning. Which action will most likely correct the problem with FastEthernet0/1? A clock rate should be added to the interface configuration. The subnet mask should be added to the interface configuration. An interface description needs to be added to the interface configuration. The no shutdown command needs to be added to the interface configuration. 3Refer to the exhibit. A router interface is configured with the command ip address 172.16.3.31 255.255.192.0. Which set o values would allow a computer that is connected to the router interface to communicate with remote networks? A: 172.16.3.254 B: 255.255.192.0 C: 172.16.3.31 A: 172.16.3.31 B: 255.255.192.0 C: 172.16.3.255 A: 172.16.3.254 B: 255.255.255.0 C: 172.16.3.31 A: 172.16.3.31 B: 255.255.255.0 C: 172.16.3.1 4Refer to the exhibit. On the basis of the show running-config output, which option correctly reflects the routes that will b routing table? ssss 5Refer to the exhibit. PC1 is unable to access the Internet. What is the cause of the problem? An incorrect IP address is configured between the two routers. No static route is configured on Router2. A routing loop has occurred. No routing protocol is configured on either of the two routers. Refer to the exhibit. Which three statements are true of the routing table for Router1? (Choose three.) The route to network 172.16.0.0 has an AD of 156160. T he route to network 172.16.0.0 has an AD of 156160. Network 192.168.0.16 can best be reached using FastEthernet0/0. The AD of EIGRP routes has been manually changed to a value other than the default value. Router1 is running both the EIGRP and OSPF routing process. Network 172.17.0.0 can only be reached using a default route. No default route has been configured. 7Refer to the exhibit. The network has three connected routers: R1, R2, and R3. The routes of all three routers are d are operational and pings are not blocked on this network. Which ping will fail? from R1 to 172.16.1.1 from R1 to 192.168.3.1 from R2 to 192.168.1.1 f rom R2 to 192.168.1.1 from R2 to 192.168.3.1 8Refer to the exhibit. A network administrator has configured OSPF using the following command: network 192.168.1.32 0.0.0.31 area 0Which router interface will participate in OSPF? FastEthernet0/0 FastEthernet0/1 Serial0/0/0 Serial0/0/1 9Refer to the exhibit. The hosts on the R1 LAN are unable to access the Internet. What is incorrectly configured? the IP address of the Fa0/0 interface at R1 the IP address of the S0/0/1 interface at R2 the IP address of the S0/0/0 interface at R1 the subnet mask of the S0/0/1 interface at R2 t he subnet mask of the S0/0/1 interface at R2 10Refer to the exhibit. Host A is having problems accessing server A. All routers have the same EIGRP configuration What should be done so that host A can access server A? Add the command no auto-summary on all routers. Change the network statements to include a wildcard mask. Adjust the EIGRP hello timers to account for the network delay.Add the command eigrp log-neighbor-changes on all routers. Which feature of RIPv2 enables it to function as a classless routing protocol? Subnet masks are included in routing updates. Routing updates are triggered by topology changes. Next-hop addresses are included in routing updates. N ext-hop addresses are included in routing updates. Multicast addresses are used to send routing updates. 12A network administrator must use the subnet 172.16.128.0/18 to create 6 additional subnets each containing up to 2LANs. Which subnet mask should the administrator use to create the new subnets? 255.255.224.0 255.255.240.0 255.255.248.0 255.255.252.0 13A network administrator is in charge of two separate networks that share a single building. What device will be requ two networks and add a common connection to the Internet that can be shared? hub router access point Ethernet switch 14Refer to the exhibit. What needs to be done to allow these two routers to connect successfully? Add a clock rate to S0/0/0 on R1. Add an interface description to S0/0/1 on R2. Change the serial interface on R2 to S0/0/0 so that it matches R1. Change the IP address of S0/0/1 on R2 so that it is in the same subnet as R1. 15In which situation would a default static route be recommended? when connecting an edge router to the Internet when variable length subnet masking is in effect when there is more than one valid route for a destination network when a destination network has a larger mask than any routes in the routing table Refer to the exhibit. A network engineer has run the show version command on R3. Upon rebooting, R3 does not load configuration settings. What could be the cause of this problem? There is insufficient NVRAM. There is insufficient flash memory. The configuration register is not configured with the default setting. The system image file is not located in NVRAM. 17Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this? The IP address of host A is incorrect. The default gateway of host A is incorrect. The Fa0/1 interfaces of the two routers are configured for different subnets. The subnet mask for the Fa0/0 interface of R1 is incorrect. 18Refer to the exhibit. R1 and R2 are adjacent routers both running RIP. All interfaces on both routers are correctly c operational. Both routers are configured to include all connected interfaces in routing updates. R2 is not showing an the routing table. What is the likely cause? The adjacent interfaces are passive. The distance of 120 exceeds 15 hops. R2 will not accept version 1 updates from R1.19W hich two technologies can be used in distance vector routing protocols to prevent routing loops? (Choose two.) authentication link-state advertisements hold-down timers Spanning Tree Protocol split horizon 20Which prompt is used to allow a user to change the IP address of an interface on a router? Router> Router# Router(config)# Router(config-if)# Refer to the exhibit. A network administrator adds this command to router R1: ip route 192.168.2.0 255.255.255.0 S0/0/0 result of adding this command? This route is automatically propagated throughout the network. The traffic for network 172.16.1.0 is forwarded to network 192.168.2.0. A static route is established. The traffic for all Class C networks is forwarded to 172.16.1.2. 22Refer to the exhibit. What information can be determined from the displayed output? EIGRP packets are waiting to be sent to the neighbors. The adjacencies between the routers are yet to be established. The IP address 192.168.10.10 is configured at serial interface S0/0/1 of router R2. Router R2 is receiving hello packets from a neighbor with the IP address 192.168.10.10 via the R2 S0/0/1 inte23Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this entering a password? ole line. The login command was not entered on the consThe enable password should be an enable secret password. No username and password combination has been configured. Console connections cannot be configured to require users to provide passwords. 24W hich of the following are primary functions of a router? (Choose two.) packet switching microsegmentation domain name resolution path selection flow control 25Because of a topology change, the next hop IP address in the current static route must be reconfigured. How can altered to accommodate a topology change? Keep the existing static route and configure a new static route with the correct next hop IP address. Negate the existing static route and configure a new static route with the correct next hop IP address. Do nothing. The existing static route will automatically update the next hop entry with the new IP address. Keep the existing static route, reload the router, and configure a new static route with the correct next hop IP Refer to the exhibit. All routers are configured with no auto-summary. All routers have a default route via their Serial0 Router B receives a packet with a destination of 10.16.1.98. What path will the packet take?B-E B-E-D-A B-E-D-A then loop A-D-A until the TTL expires B will immediately drop the packet. There is insufficient information to answer the question. 27Refer to the exhibit. A network administrator is investigating why data packets with destination addresses of 172.16.192.168.10.100 are being dropped instead of being forwarded via the static route as expected. After confirming that ip command has been applied on all routers in the network, what other action should the administrator take to ensure these addresses are forwarded via the static route? Check that all routers are configured with the same autonomous system number. Issue the n ono auto-summary command within the EIGRP configuration of all routers. Issue the n ono passive-interface command within the EIGRP configuration of all routers. Configure the static route to point to the next hop address instead of the outbound interface. 28If a router is booting with its default configuration register setting and its NVRAM lacks boot system commands, from router try to load the IOS image first? ROM RAM NVRAM flash TFTP server T FTP server 29T wo routers need to be configured within a single OSPF area. Which two components need to be configured on bo this? (Choose two.) the same process ID the same area ID network addresses and wildcard masks the same router ID the same loop back address 30Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (10.0.0.0/8 64.100.0.0/16 128.107.0.0/16 172.16.40.0/24 192.168.1.0/24 192.168.2.0/24 Which candidate route has the longest match for a packet with a destination address of 10.30.16.48? 10.30.0.0/16 10.30.15.0/23 10.30.16.0/24 10.30.16.32/27 10.30.16.32/30 32W hich three statements are true regarding the encapsulation and de-encapsulation of packets when traveling throug (Choose three.) The router modifies the TTL field, decrementing it by one. The router changes the source IP to the IP of the exit interface. The router maintains the same source and destination IP. T he router changes the source physical address to the physical address of the exit interface.The router changes the destination IP to the IP of the exit interface. The router sends the packet out all other interfaces, besides the one it entered the router on. 33Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two rou establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem? Check if the interfaces of the routers are enabled. Check the hello and dead intervals between the routers. Check the process ID of both routers. Check if CDP is enabled on all the routers. 34W hich mechanism helps to avoid routing loops by advertising a metric of infinity? route poisoning split horizon hold-down timer triggered updates 35o devices Refer to the exhibit. A device is required to complete the connection between router R1 and the WAN. Which tw for this? (Choose two.) a CSU/DSU device a modem an Ethernet switch a hub a bridge 36Why is fast convergence desirable in networks that use dynamic routing protocols? Hosts are unable to access their gateway until the network is converged. Routers will not allow packets to be forwarded until the network is converged. Routers may make incorrect forwarding decisions until the network has converged. Routers will not allow configuration changes to be made until the network has converged. 37Refer to the exhibit. R1 is configured properly for a single area OSPF, and R2 has been recently installed in the ne commands is required to configure a single area OSPF for the networks that are connected to R2? R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config)# router ospf 2R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 1R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.0.0.0 0.0.0.3 area 138Refer to the exhibit. Which path will traffic from the 172.16.1.0/24 network take to get to the 10.0.0.0/24 network? ADC ABC It will load balance the traffic between ADC and ABC It will send the traffic via ABC, and will use ADC as a backup path only when ABC fails. 39W hat are two ways that a router can learn of the paths to destination networks? (Choose two.) updates from other routers DHCP information broadcasts manual configuration of routes ARP requests from connected routers inspection of the destination IP address in data packets updates from the SMTP management information base u pdates from the SMTP management information base 40Refer to the exhibit. The network administrator has run the following command on R1. R1(config)# ip route 192.168.2.0 255.255.255.0 172.16.1.2What is the result of running this command? Traffic for network 192.168.2.0 is forwarded to 172.16.1.2. This route is automatically propagated throughout the entire network. Traffic for all networks is forwarded to 172.16.1.2. The command invokes a dynamic routing protocol for 192.168.2.0. Refer to the exhibit. What is the meaning of the highlighted value 120? It is the metric that is calculated by the routing protocol. It is the value that is used by the DUAL algorithm to determine the bandwidth for the link. It is the administrative distance of the routing protocol. It is the hold-down time, measured in seconds, before the next update. I t is the hold-down time, measured in seconds, before the next update. 42Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes down. Which statement Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes down. Which statemen how the routers in this topology will respond to this event? Router4 will learn about the failed route 30 seconds later in the next periodic update. Split horizon will prevent Router4 from fowarding packets to the 10.0.0.0 network until the holddown timer expiRouter5 immediately flushes the unreachable route from its routing table. Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0. 43 o Refer to the exhibit. Which combination of IP address and subnet mask can be used on the serial interface of Rout interface in the same network as the serial interface of Router1? IP 172.16.0.18, subnet mask 255.255.255.0 IP 172.16.32.15, subnet mask 255.255.255.240 IP 172.16.0.18, subnet mask 255.255.255.252 IP 172.16.32.18, subnet mask 255.255.255.252 44W hich statement is true about the RIPv1 protocol? It is a link-state routing protocol. It excludes subnet information from the routing updates. It uses the DUAL algorithm to insert backup routes into the topology table. It uses classless routing as the default method on the router. 45Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2? 192.168.1.0/24 192.168.0.0/24 192.168.0.0/22 192.168.1.0/22 Which two statements are true for link-state routing protocols? (Choose two.) Routers that run a link-state protocol can establish a complete topology of the network. Routers in a multipoint network that run a link-state protocol can exchange routing tables. Routers use only hop count for routing decisions. T he shortest path first algorithm is used.Split horizon is used to avoid routing loops. ts the best route and will b 47A router learns about network 192.168.10.128/27 from multiple sources. Which option represenrouting table? S 192.168.10.128/27 [1/0] via 192.168.10.226 R 192.168.10.128/27 [120/2] via 192.168.10.226, 00:00:14, Serial0/0/0 O 192.168.10.128/27 [110/1563] via 192.168.10.226, 00:00:09, Serial0/0/0 D 192.168.10.128/27 [90/21026560] via 192.168.10.226, 00:00:16, Serial0/0/0 48Refer to the exhibit. When all of the commands that are shown in the exhibit are entered at the correct router prom of the router? name cisco router hostname 49W hich statement is true about the metrics used by routing protocols? A metric is a value used by a particular routing protocol to compare paths to remote networks. A common metric is used by all routing protocols. The metric with the highest value is installed in the routing table. The router may use only one parameter at a time to calculate the metric. 50Which two statements are true about the EIGRP successor route? (Choose two.) It is saved in the topology table for use if the primary route fails. It may be backed up by a feasible successor route. It is used by EIGRP to forward traffic to the destination. It is flagged as active in the routing table. After the discovery process has occurred, the successor route is stored in the neighbor table. in the output of the Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as shownshow ip rip databa However, upon running the show ip route command, the network administrator sees that the router has installed a dif 192.168.6.0 network learned via EIGRP. What could be the reason for the missing RIP route? Compared to RIP, EIGRP has a lower administrative distance. Compared to EIGRP, RIP has a higher metric value for the route. Compared to RIP, the EIGRP route has fewer hops. Compared to RIP, EIGRP has a faster update timer. 52A network administrator is analyzing routing update behavior on a network that has both EIGRP and OSPF configu Both protocols appear in the output of show ip protocols. However, only EIGRP internal routes appear in the routing The EIGRP protocol has a lower administrative distance than OSPF.。