形位公差中英文

合集下载

形位公差用语中英文对照

形位公差用语中英文对照(总1页)-CAL-FENGHAI.-(YICAI)-Company One1-CAL-本页仅作为文档封面，使用请直接删除公差/值(tolerance/value)基本尺寸(basic size)偏差(deviation)上/下偏差(upper/lower deviation)配合/间隙配合/过盈配合/过渡配合(fit/clearance fit/interference fit/ transition fits) 单/双边公差(unilateral/bilateral tolerance)标准/精度公差(standard/ precision tolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis)最大/小材料状态(M/LMC=maximum/least material condition)理论正确尺寸(theoretical size )基本尺寸(basic dimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profile of a line)面轮廓度(profile of a surface)定向公差(orientation tolerance)平行度(parallelism)垂直度(perpendicularity)倾斜度(角度) (angularity)位置度(position)对称度(symmetry)同轴度(同心度) (concentricity)圆跳动(circular runout)全跳动(total runout)坐标尺寸(coordinate dimensioning)拔模斜度(draft angle)分型线(parting line)外圆角/内圆角拔模斜度(rounds/fillets draft) 肋材和尖角(rib and corner)顶/测/端视图(top/side/ end view)公差/值(tolerance/value)基本尺寸(basic size)偏差(deviation)2上/下偏差(upper/lower deviation)配合/间隙配合/过盈配合/过渡配合(fit/clearance fit/interference fit/ transition fits) 单/双边公差(unilateral/bilateral tolerance)标准/精度公差(standard/ precision tolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis)最大/小材料状态(M/LMC=maximum/least material condition)理论正确尺寸(theoretical size )基本尺寸(basic dimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profile of a line)面轮廓度(profile of a surface)定向公差(orientation tolerance)平行度(parallelism)垂直度(perpendicularity)倾斜度(角度) (angularity)位置度(position)对称度(symmetry)同轴度(同心度) (concentricity)圆跳动(circular runout)全跳动(total runout)坐标尺寸(coordinate dimensioning)几何尺寸(geometric dimensioning)拔模斜度(draft angle)分型线(parting line)外圆角/内圆角拔模斜度(rounds/fillets draft) 肋材和尖角(rib and corner)顶/测/端视图(top/side/ end view)3。

形位公差符号常用语(中英文双语)

上/下偏差(upper/lower deviation) 形位公差符号常用语 (中英文双语)配合/间隙配合/过盈配合/过渡配合(fit/clearance fit/interference fit/ 公差/值(tolerance/value)transition fits) 基本尺寸(basic size) 单/双边公差(unilateral/bilateral tolerance)偏差(deviation) 标准/精度公差(standard/ precision tolerance)上/下偏差(upper/lower deviation) 基准/特征/点/线/平面/轴线配合/间隙配合/过盈配合/过渡配合(datum/feature/point/line/ plane/axis) (fit/clearance fit/interference fit/ 最大/小材料状态(M/LMC=maximum/least transition fits) material condition) 单/双边公差(unilateral/bilateral tolerance) 理论正确尺寸(theoretical size ) 标准/精度公差(standard/ precision tolerance) 基本尺寸(basic dimension) 基准/特征/点/线/平面/轴线直径/半径(diameter/radius) (datum/feature/point/line/ plane/axis) 直线度(straightness) 最大/小材料状态(M/LMC=maximum/least 平面度(flatness)material condition) 圆度(circularity)理论正确尺寸(theoretical size ) 圆柱度(cylindricity) 基本尺寸(basic dimension) 线轮廓度(profile of a line) 直径/半径(diameter/radius) 面轮廓度(profile of a surface) 直线度(straightness) 定向公差(orientation tolerance) 平面度(flatness) 平行度(parallelism) 圆度(circularity) 垂直度(perpendicularity) 圆柱度(cylindricity)线轮廓度(profile of a line)面轮廓度(profile of a surface)倾斜度(角度) (angularity) 定向公差(orientation tolerance)位置度(position) 平行度(parallelism)对称度(symmetry) 垂直度(perpendicularity)同轴度(同心度) (concentricity) 倾斜度(角度) (angularity)圆跳动(circular runout) 位置度(position)全跳动(total runout) 对称度(symmetry)坐标尺寸(coordinate dimensioning) 同轴度(同心度) (concentricity)几何尺寸(geometric dimensioning) 圆跳动(circular runout)拔模斜度(draft angle) 全跳动(total runout)分型线(parting line) 坐标尺寸(coordinate dimensioning)外圆角/内圆角拔模斜度(rounds/fillets draft) 拔模斜度(draft angle) 肋材和尖角(rib and corner) 分型线(parting line)顶/测/端视图(top/side/ end view) 外圆角/内圆角拔模斜度(rounds/fillets draft)肋材和尖角(rib and corner) 顶/测/端视图(top/side/ end view) 标题] 12. 形位公差符号常用语 (中英文双语) 公差/值(tolerance/value) properties 基本尺寸(basic size)偏差(deviation)游泳待四、容易拼写错的数字 14. tear (tore, torn) 撕9. discover—discovery发4. twelfth第十二5. twentieth碎 16.wear( wore; 现 10. bury—burial埋葬第二十 worn) 穿/戴 11. conclude—conclusion 得出结四、亲属称呼17.hold (held, 论 12. arrive—arrival 到达2. niece (女性晚辈)3. nephew (男held ) 18.make 13. weigh—weight 重性晚辈) 4. cousin (同辈兄弟姐妹) 5.(made, made) 量 14. 五、以下动词加-ed 或-ing要双写最19. keep (kept, kept) describe—description 描述后一个字母七、意思相近的词 15. lose—loss 损失 16. 1. regret (regretted, regretting) 1. check (核对)/ examine(检anxious---anxiety 焦虑后悔 3. admit (admitted, 查)/ test(测试) 十二、注意形容词变副词时的拼写变admitting) 承认 4. occur 2. receive(收到) / accept(接化(occurred, occurring) 出现受) 1. beautiful美丽的5. prefer (preferred, preferring) 3. destroy (毁坏;毁灭)/ damage—beautifully 2. possible可宁愿 6. refer (referred, (破坏) 能的—possibly referring) 提到 4. celebrate(庆祝)/ congratulate3. practical实际的7. forget (forgetting ) 忘(祝贺) —practically 4. particular记 8. permit 5. wear sth / dress sb 穿衣特别的—particularly (permitted, permitting)允许八、注意形容词变名词时的拼写变化 5. successful成功的9. equip (equipped, equipping) 装1. long—length 长度2. —successfully 备 wide—width 宽度3. high—height 十三、其它必背单词注意:quarrel, signal, travel中的高度 1. abroad 国外 2. absence n. 缺l可双写(英国英语)也可不双写(美4. strong—strength力量席 (absent adj.) 3. accept 接国英语) 九、以-ic结尾的动词，应先把-ic变受)六、部分过去式和过去分词不规则变为-ick，再加ing或ed 4. accident事故 (accidental adj. 化的动词 1. picnic (picnicked, picnicking) 偶然的，accidentally adv. 偶然地) 1. broadcast (broadcast, broadcast) 野餐 5. achievement成就 (achieve v. 获广播 2. flee (fled, fled) 逃十、个别名词的复数拼写得) 6. address地址 7. 跑 1. German (Germans) 德国人 2. gulf admire钦佩3. forbid (forbade, forbidden) 禁(gulfs) 海湾 3. handkerchief 8.admit承止 4. forgive (forgave, (handkerchiefs) 手帕roof (roofs) 认(admitted) 9. forgiven) 原谅房顶 agreement 协议 5. freeze (froze, frozen) 结冰 4. hero (英雄)，potato (土豆)，10. agriculture农业 6. hang (作“绞死”讲，是规则的;tomato (西红柿) 等有生命的以-o结(agricultural adj. 农业作“悬挂”讲，其过去式过去分词都尾的名词变复数时要加-es。

形位公差用语中英文对照

公差/值(tolerance/value)基本尺寸(basic size)偏差(deviation)上/下偏差(upper/lower deviation)配合/间隙配合/过盈配合/过渡配合(fit/clearance fit/interference fit/ transition fits) 单/双边公差(unilateral/bilateral tolerance)标准/精度公差(standard/ precision tolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis)最大/小材料状态(M/LMC=maximum/least material condition)理论正确尺寸(theoretical size )基本尺寸(basic dimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profile of a line)面轮廓度(profile of a surface)定向公差(orientation tolerance)平行度(parallelism)垂直度(perpendicularity)倾斜度(角度) (angularity)位置度(position)对称度(symmetry)同轴度(同心度) (concentricity)圆跳动(circular runout)全跳动(total runout)坐标尺寸(coordinate dimensioning)拔模斜度(draft angle)分型线(parting line)外圆角/内圆角拔模斜度(rounds/fillets draft) 肋材和尖角(rib and corner)顶/测/端视图(top/side/ end view)公差/值(tolerance/value)2基本尺寸(basic size)偏差(deviation)上/下偏差(upper/lower deviation)配合/间隙配合/过盈配合/过渡配合(fit/clearance fit/interference fit/ transition fits) 单/双边公差(unilateral/bilateral tolerance)标准/精度公差(standard/ precision tolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis)最大/小材料状态(M/LMC=maximum/least material condition)理论正确尺寸(theoretical size )基本尺寸(basic dimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profile of a line)面轮廓度(profile of a surface)定向公差(orientation tolerance)平行度(parallelism)垂直度(perpendicularity)倾斜度(角度) (angularity)位置度(position)对称度(symmetry)同轴度(同心度) (concentricity)圆跳动(circular runout)全跳动(total runout)坐标尺寸(coordinate dimensioning)几何尺寸(geometric dimensioning)拔模斜度(draft angle)分型线(parting line)外圆角/内圆角拔模斜度(rounds/fillets draft) 肋材和尖角(rib and corner)顶/测/端视图(top/side/ end view)22。

形位公差用语中英文对照

形位公差用语中英文对照Document serial number【LGGKGB-LGG98YT-LGGT8CB-LGUT-LGG08】公差/值(tolerance/value)基本尺寸(basic size)偏差(deviation)上/下偏差(upper/lower deviation)配合/间隙配合/过盈配合/过渡配合(fit/clearancefit/interference fit/ transition fits)单/双边公差(unilateral/bilateral tolerance)标准/精度公差(standard/ precision tolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis)最大/小材料状态(M/LMC=maximum/least material condition) 理论正确尺寸(theoretical size ) 基本尺寸(basic dimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profile of a line)面轮廓度(profile of a surface) 定向公差(orientation tolerance) 平行度(parallelism)垂直度(perpendicularity)倾斜度(角度) (angularity)位置度(position)对称度(symmetry)同轴度(同心度) (concentricity)圆跳动(circular runout)全跳动(total runout)坐标尺寸(coordinate dimensioning)拔模斜度(draft angle)分型线(parting line)外圆角/内圆角拔模斜度(rounds/fillets draft) 肋材和尖角(rib and corner)顶/测/端视图(top/side/ end view)公差/值(tolerance/value)基本尺寸(basic size)偏差(deviation)上/下偏差(upper/lower deviation)配合/间隙配合/过盈配合/过渡配合(fit/clearance fit/interference fit/ transition fits)单/双边公差(unilateral/bilateral tolerance) 标准/精度公差(standard/ precision tolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis)最大/小材料状态(M/LMC=maximum/least material condition) 理论正确尺寸(theoretical size )基本尺寸(basic dimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profile of a line) 面轮廓度(profile of a surface)定向公差(orientation tolerance) 平行度(parallelism)垂直度(perpendicularity)倾斜度(角度) (angularity)位置度(position)对称度(symmetry)同轴度(同心度) (concentricity)圆跳动(circular runout)全跳动(total runout)坐标尺寸(coordinate dimensioning)几何尺寸(geometric dimensioning) 拔模斜度(draft angle)分型线(parting line) 外圆角/内圆角拔模斜度(rounds/fillets draft) 肋材和尖角(rib and corner)顶/测/端视图(top/side/ end view)。

形状位置公差及英文翻译

形状位置公差及英文翻译
零件在加工过程中，由于机床－夹具－刀具系统存在几何误差，以及加工中出现受力变形、热变形、振动和磨损等影响，使被加工零件的几何要素不可避免地产生误差。

这些误差包括尺寸偏差、形状误差(包括宏观几何误差、波度和表面粗糙度)及位置误差。

形状公差
形状公差是指单一实际要素的形状所允许的变动全量。

形状公差用形状公差带表达。

形状公差带包括公差带形状、方向、位置和大小等四要
素。

形状公差项目有：直线度、平面度、圆度、圆柱度、线轮廓度、面轮廓度等6项。

位置公差
位置公差是指关联实际要素的位置对基准所允许的变动全量。

∙定向公差
定向公差是指关联实际要素对基准在方向上允许的变动全量。

这类公差包括平行度、
垂直度、倾斜度3项。

∙定位公差
定位公差是关联实际要素对基准在位置上允许的变动全量。

这类公差包括同轴度、对
称度、位置度3项。

∙跳动公差
跳动公差是以特定的检测方式为依据而给定的公差项目。

跳动公差可分为圆跳动与全
跳动。

零件的形位公差共14项，其中形状公差6个，位置公差8个，列于下表。

英汉对译。

中英文公差对照

尺寸公差： Dimensional tolerance
公差=上偏差-下偏差
Tolerance =upper deviation -ower deviation 误差error
形位公差： Shape and position tolerance
形状公差: 直线度 straightness
平面度flatness
圆度 roundness
水平度
level surface
圆柱度 cylindrical shape cylinder
线轮廓度line shape
面轮廓度surface shape
sin^riin ■ r r ・urrF ・u ・・ r r ■ n ・・・■»■ i ・・
• ■ i - B 1 * ? S 号
直幕BE
平药jr 口誉庫 0
Vi tk BL XX
雲乾口圧 r\ 面乾J*度
时株dt
2形位公差：考舉概念！（4分）购
羞 £
位置公差: 平行度parallelism
垂直度verticality
倾斜度inclination
同轴度coaxiality
对称度symmetry
位置度
圆跳动
全跳动
端面全跳动overall axial run-out 径面全跳动overall radial run-out
surface roughness
从表面指向实体内point from the surface to the entity
欢迎您的下载，
资料仅供参考!
致力为企业和个人提供合同协议，策划案计划书，学习资料等等
打造全网一站式需求。

形位公差的英文缩写

形位公差的英文缩写有：M、P、E、L、R、F，请问哪位大虾知道它们的英文全称。

自己对应看看吧！！！形位公差符号常用语 (中英文双语)公差/值(tolerance/value)基本尺寸(basic size)偏差(deviation)上/下偏差(upper/lower deviation)配合/间隙配合/过盈配合/过渡配合(fit/clearance fit/interference fit/ transition fits) 单/双边公差(unilateral/bilateral tolerance)标准/精度公差(standard/ precision tolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis)最大/小材料状态(M/LMC=maximum/least material condition)理论正确尺寸(theoretical size )基本尺寸(basic dimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profile of a line)面轮廓度(profile of a surface)定向公差(orientation tolerance) 平行度(parallelism)垂直度(perpendicularity)倾斜度(角度) (angularity)位置度(position)对称度(symmetry)同轴度(同心度) (concentricity)圆跳动(circular runout)全跳动(total runout)坐标尺寸(coordinate dimensioning)几何尺寸(geometric dimensioning)拔模斜度(draft angle)分型线(parting line)外圆角/内圆角拔模斜度(rounds/fillets draft) 肋材和尖角(rib and corner)顶/测/端视图(top/side/ end view)。

形位公差量具中英文对照

w
countersink
x
depth
y
conical taper
z
slope (flat taper)
`
plus/minus
~
degree
^
arc length
Rough
AMG DT
a b c e f g h I j d k l n o r p t m u v w x y z ` ~ ^
中文名称
倾斜度垂直度平面度
English name
电子称塞尺专用量具 X-探伤仪光谱仪轮廓度仪数显卡尺气动量仪三坐标螺紋塞规目視电子高度尺针规深度卡尺 R规拉力测试机块规百分表千分表千分尺膜厚仪硬度計 2D投影仪万能角度尺扭力扳手推拉力计平台
Balance Thickness gage
DIR
MR OTG HB ME APR TS PPM PF
本项目使用检测设备/检具
序号中文名稱 English name
1
电子称
Balance
2 X-探伤仪
X-ray
3 数显卡尺
Caliper
4 螺紋塞规 Thread gage
5 深度卡尺 Depth caliper
6
目視
Vision
缩写
BE X-ray
Dial indicator
Micrometer Oil's thickness gage
Hardometer microscope Angle protractor Torque spanner Push - Pull meter Platform
缩写
BE TG SG X-ray SR PM CR AG CMM TG Vis HG PG DC RG UTM BK

形位公差用语中英文对照

公差/值(tolerance/value)基本尺寸(basic size)偏差(deviation)上/下偏差(upper/lower deviation)配合/间隙配合/过盈配合/过渡配合(fit/clearance fit/interference fit/ transition fits) 单/双边公差(unilateral/bilateral tolerance)标准/精度公差(standard/ precision tolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis)最大/小材料状态(M/LMC=maximum/least material condition)理论正确尺寸(theoretical size )基本尺寸(basic dimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profile of a line)面轮廓度(profile of a surface)定向公差(orientation tolerance)平行度(parallelism)垂直度(perpendicularity)倾斜度(角度) (angularity)位置度(position)对称度(symmetry)同轴度(同心度) (concentricity)圆跳动(circular runout)全跳动(total runout)坐标尺寸(coordinate dimensioning)拔模斜度(draft angle)分型线(parting line) 外圆角/内圆角拔模斜度(rounds/fillets draft)肋材和尖角(rib and corner)顶/测/端视图(top/side/ end view)公差/值(tolerance/value)基本尺寸(basic size)偏差(deviation)上/下偏差(upper/lower deviation)配合/间隙配合/过盈配合/过渡配合(fit/clearance fit/interference fit/ transition fits) 单/双边公差(unilateral/bilateral tolerance)标准/精度公差(standard/ precision tolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis)最大/小材料状态(M/LMC=maximum/least material condition)理论正确尺寸(theoretical size )基本尺寸(basic dimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profile of a line)面轮廓度(profile of a surface)定向公差(orientation tolerance)平行度(parallelism)垂直度(perpendicularity)倾斜度(角度) (angularity)位置度(position)对称度(symmetry)同轴度(同心度) (concentricity)圆跳动(circular runout)全跳动(total runout)坐标尺寸(coordinate dimensioning)几何尺寸(geometric dimensioning) 拔模斜度(draft angle)分型线(parting line) 外圆角/内圆角拔模斜度(rounds/fillets draft) 肋材和尖角(rib and corner)顶/测/端视图(top/side/ end view)。

形位公差符号常用语(中英)

形位公差符号常用语 (中英文对照)公差/值(tolerance/value) ['tɔlərəns] ['vælju:]基本尺寸(basic size) ['beisik]偏差(deviation) [,di:vi'eiʃən]上/下偏差(upper/lower deviation) ['ʌpə] ['ləuə]配合/间隙配合/过盈配合/过渡配合(fit/clearance fit/interference fit/ transition fits) ['fit] ['kliərəns] [,intə'fiərəns] [træn'siʒən, -'ziʃən, trɑ:n-]单/双边公差(unilateral/bilateral tolerance) [,ju:ni'lætərəl] [,bai'lætərəl]标准/精度公差(standard/ precision tolerance) ['stændəd] [pri'siʒən]基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis) ['deitəm] ['fi:tʃə] [pɔint] [plein] ['æksis]最大/小材料状态(M/LMC=maximum/least material condition) ['mæksiməm] [li:st] [mə'tiəriəl] [kən'diʃən]理论正确尺寸(theoretical size ) [,θiə'retikəl, ,θi:ə-]基本尺寸(basic dimension) [di'menʃən]直径/半径(diameter/radius) [dai'æmitə] ['reidiəs]直线度(straightness) ['streitnis]平面度(flatness) ['flætnis]圆度(circularity) [,sə:kju'lærəti]圆柱度(cylindricity)线轮廓度(profile of a line) ['prəufail]面轮廓度(profile of a surface) ['sə:fis] 表面；表层；外观['prəufail]轮廓；外形定向公差(orientation tolerance) [,ɔ:rien'teiʃən, əu-]平行度(parallelism) ['pærəlelizəm]垂直度(perpendicularity) ['pə:pen,dikju'læriti]倾斜度(角度) (angularity) [,æŋɡju'lærəti]位置度(position)对称度(symmetry) ['simitri]同轴度(同心度) (concentricity) [kɔnsen'trisiti]圆跳动(circular runout) ['sə:kjulə] ['rʌnaut]全跳动(total runout) ['təutəl] 全部的；完全的；整个的.总数，合计坐标尺寸(coordinate dimensioning) [kəu'ɔ:dinit] [di'menʃəniŋ]尺寸标注；标示尺寸几何尺寸(geometric dimensioning) [dʒiəu'metrik]拔模斜度(draft angle) [drɑ:ft, dræft] ['æŋɡl]分型线(parting line) ['pɑ:tiŋ]外圆角/内圆角拔模斜度(rounds/fillets draft) [raunds] ['filits]肋材和尖角(rib and corner) [rib] ['kɔ:nə]顶/测/端视图(top/side/ end view) [tɔp] [vju:]。

形位公差中英文对照

形位公差中英文对照设计手册——形位公差符号对应英语Straightness直线度- a condition where an element of a surface or an axis is a straight line.Flatness平面度- is the condition of a surface having all elements in one plane.Roundness圆度- describes the condition on a surface of revolution (cylinder, cone, sphere) where all points of the surface intersected by any plane.Cylindricity圆柱度- describes a condition of a surface of revolution in which all points of a surface are equidistant from a common axis.Profile of a Line线轮廓度- is the condition permitting a uniform amount of profile variation, ether unilaterally or bilaterally, along a line element of a feature.Profile of a Surface面轮廓度 - is the condition permitting a uniform amount of profile variation, ether unilaterally or bilaterally, on a surface. All Around Symbol全周符号 - indicating that a tolerance applies to surfaces all around the part.Angularity倾斜度- is the condition of a surface, axis, or centerplane, which is at a specified angle from a datum plane or axis. Perpendicularity垂直度 - is the condition of a surface, axis, or line, which is 90 deg. From a datum plane or a datum axis.Parallelism平行度- is the condition of a surface, line, or axis, which is equidistant at all points from a datum plane or axis.Position Tolerance位置度 - defines a zone within which the axis or center plane of a feature is permitted to vary from true (theoretically exact) position.Concentricity同轴度 - describes a condition in which two or more features , in any combination, have a common axis.Symmetry对称度- is a condition in which a feature (or features) is symmetrically disposed about the center plane of a datum feature. Runout圆跳动- is the composite deviation from the desired form of a part surface of revolution through on full rotation (360 deg) of the part on a datum axis.Total Runout全跳动 - is the simultaneous composite control of all elements of a surface at all circular and profile measuring positions as the part is rotated through 360.Maximum Material Condition (MMC) 最大实体要求- is that condition of a part feature wherein it contains the maximum amount ofmaterial within the stated limits of size. That is: minimum hole size and maximum shaft size.Least Material Condition (LMC)最小实体要求- implies that condition of a part feature of size wherein it contains the least (minimum) amount of material, examples, largest hole size and smallest shaft size. It isopposite to maximum material condition.Regardless Of Feature Size (RFS) - the condition where the tolerance of form, runout or location must be met irrespective of where the feature lies within its size tolerance.Projected T olerance Zone延伸公差带- applies to a hole in which a pin, stud, screw, etc., is to be inserted. It controls the perpendicularity of the hole to the extent of the projection from the hole and as it relates to the mating part clearance. The projected tolerance zone extends above the surface of the part to the functional length of the pin, stud, and screw relative to its assembly with the mating part.Tangent Plane相切面- indicating a tangent plane is shown. The symbol is placed in the feature control frame following the stated tolerance.Free State Variations自由状态变形 - is a term used to describe distortion of a part after removal of forces applied during manufacture. Diameter直径- indicates a circular feature when used on the field of a drawing or indicates that the tolerance is diametrical when used in a feature control frame.Basic Dimension基本尺寸 - used to describe the exact size, profile, orientation or location of a feature. A basic dimension is always associated with a feature control frame or datum target. (Theoretically exact dimension in ISO)Reference Dimension参考尺寸- a dimension usually without tolerance,used for information purposes only. It does not govern production or inspection operations. (Auxiliary dimension in ISO) Datum Feature参考特征- is the actual component feature used to establish a datum.Dimension Origin尺寸源- Signifies that the dimension originates from the plane established by the shorter surface and dimensional limits apply to the other surface.Feature Control Frame公差控制框- is a rectangular box containing the geometric characteristics symbol, and the form, runout or location tolerance. If necessary, datum references and modifiers applicable to the feature or the datums are also contained in the box.Conical Taper - is used to indicate taper for conical tapers. This symbol is always shown with the vertical leg to the left.Slope坡度- is used to indicate slope for flat tapers. This symbol is always shown with the vertical leg to the left.Counterbore/Spotface沉孔- is used to indicate a counterbore or a spotface. The symbol precedes the dimension of the counterbore or spotface, with no spaceCountersink埋头孔 - is used to indicate a countersink. The symbol precedes the dimensions of the countersink with no space.Depth/Deep深度- is used to indicate that a dimension applies to thedepth of a feature. This symbol precedes the depth value with no space in between.Square - is used to indicate that a single dimension applies to a square shape. The symbol precedes the dimension with no space between. Number of Places位置数量- the X is used along with a value to indicate the number of times a dimension or feature is repeated on the drawing.Arc Length弧长- indicating that a dimension is an arc length measured on a curved outline. The symbol is placed above the dimension.Radius半径- creates a zone defined by two arcs (the minimum and maximum radii). The part surface must lie within this zone.Spherical Radius球半径 - precedes the value of a dimension or tolerance.Spherical Diameter球直径- shall precede the tolerance value where the specified tolerance value represents spherical zone. Also, a positional tolerance may be used to control the location of a spherical feature relative to other features of a part. The symbol for spherical diameter precedes the size dimension of the feature and the positional tolerance value, to indicate a spherical tolerance zone.Controlled Radius可控半径 - creates a tolerance zone defined by two arcs (the minimum and maximum radii) that are tangent to the adjacent surfaces. Where a controlled radius is specified, the part contour within the crescent-shaped tolerance zone must be a fair curve without flats orreversals. Additionally, radii taken at all points on the part contour shall neither be smaller than the specified minimum limit nor larger than the maximum limit.Between - to indicate that a profile tolerance applies to several contiguous features, letters may designate where the profile tolerance begins and ends. These letters are referenced using the between symbol (since 1994) or the word between on drawings made to earlier versions of the Standard.Statistical Tolerance统计公差- is the assigning of tolerances to related components of an assembly on the basis of sound statistics (such as the assembly tolerance is equal to the square root of the sum of the squares of the individual tolerances). By applying statistical tolerancing, tolerances of individual components may be increased or clearances between mating parts may be reduced. The increased tolerance or improved fit may reduce manufacturing cost or improve the product's performance, but shall only be employed where the appropriate statistical process control will be used. Therefore, consideration should be given to specifying the required Cp and /or Cpk or other process performance indices。

形位公差符号常用语_中英文双语

形位公差符号常用语(中英文双语)公差/值(tolerance/value)基本尺寸(basic size)偏差(deviation)上/下偏差(upper/lower deviation)配合/间隙配合/过盈配合/过渡配合(fit/clearancefit/interference fit/ transition fits)单/双边公差(unilateral/bilateral tolerance)标准/精度公差(standard/ precision tolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis)最大/小材料状态(M/LMC=maximum/least material condition)理论正确尺寸(theoretical size )基本尺寸(basic dimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profile of a line)面轮廓度(profile of a surface)定向公差(orientation tolerance)平行度(parallelism)垂直度(perpendicularity)倾斜度(角度) (angularity)位置度(position)对称度(symmetry)同轴度(同心度) (concentricity)圆跳动(circular runout)全跳动(total runout)坐标尺寸(coordinate dimensioning)拔模斜度(draft angle)分型线(parting line)外圆角/内圆角拔模斜度(rounds/fillets draft)肋材和尖角(rib and corner)顶/测/端视图(top/side/ end view)公差/值(tolerance/value)基本尺寸(basic size)偏差(deviation)上/下偏差(upper/lower deviation)配合/间隙配合/过盈配合/过渡配合(fit/clearance fit/interference fit/ transition fits)单/双边公差(unilateral/bilateral tolerance)标准/精度公差(standard/ precision tolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/ plane/axis)最大/小材料状态(M/LMC=maximum/least material condition)理论正确尺寸(theoretical size )基本尺寸(basic dimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profile of a line)面轮廓度(profile of a surface)定向公差(orientation tolerance)平行度(parallelism)垂直度(perpendicularity)倾斜度(角度) (angularity)位置度(position)对称度(symmetry)同轴度(同心度) (concentricity)圆跳动(circular runout)全跳动(total runout)坐标尺寸(coordinate dimensioning)几何尺寸(geometric dimensioning)拔模斜度(draft angle)分型线(parting line)外圆角/内圆角拔模斜度(rounds/fillets draft) 肋材和尖角(rib and corner)顶/测/端视图(top/side/ end view)。

形状位置公差(中英对照)

Position (used to control symmetry)……………………………………………………………………62 Projected Tolerance Zone………………………………………………………………………………63 The Fixed Fastener Formula……………………………………………………………………………64 The Floating Fastener Formula…………………………………………………………………………65 Composite Position Tolerancing……………………………………………………………………… 66 Position (multiple single segment control)……………………………………………………………68 Zero Tolerance at MMC…………………………………………………………………………………70 Concentricity……………………………………………………………………………………… … 71 Symmetry…………………………………………………………………………………………………72 Conversion Chart……………………………………………………………………………………… 73 Surface Texture Definitions…………………………………………………………………………… 74
1
1
几何特性符号
使用参考基准公差类型
不用
形状
有时用常用
轮廓方向位置跳动
特性直线度平面度圆度圆柱度线轮廓度面轮廓度倾斜度垂直度平行度
位置度同轴度对称度圆跳动全跳动
符号

形位公差及英文翻译

基本尺寸(basic dimension)
坐标尺寸(coordinate dimensioning)
直径/半径(diameter/radius)
几何尺寸(geometric dimensioning)
直线度(straightness)
拔模斜度(draft angle)
平面度(flatness)
分型线(parting line)
状况。
位
面轮廓度公差是指非圆曲面的实际轮廓线，对理想轮廓面的允
置
许变动量。也就是图样上给定的，用以限制实际曲面加工误差
度
的变动范围。
圆跳动跳动全跳动
位置度是表示零件上的点、线、面等要素，相对其理想位置的准确状况。位置度公差是：被测要素的实际位置相对于理想位置所允许的最大变动量。
圆跳动是表示零件上的回转表面在限定的测量面内，相对于基准轴线保持固定位置的状况。圆跳动公差是：被测实际要素绕基准轴线，无轴向移动地旋转一整圈时，在限定的测量范围内，所允许的最大变动量。
变动范围。
公
差线轮廓度是表示在零件的给定平面上，任意形状的曲线，保持
其理想形状的状况。线轮廓度公差是指非圆曲线的实际轮廓线的允许变动量。也就是图样上给定的，用以限制实际曲线加工误差所允许的变动范围。
定同位轴
度
垂直度是表示零件上被测要素相对于基准要素，保持正确的 90°夹角状况。也就是通常所说的两要素之间保持正交的程度。垂直度公差是：被测要素的实际方向，对于基准相垂直的理想方向之间，所允许的最大变动量。也就是图样上给出的，用以限制被测实际要素偏离垂直方向，所允许的最大变动范围。
位置公差位置公差是指关联实际要素的位置对基准所允许的变动全量。

形位公差标注大全（附英文），小伙伴们快收藏！

形位公差标注大全（附英文），小伙伴们快收藏！公差特征项目符号有或无基准要求
形状形状直线度无平面度无圆　度无圆柱度无
形状或位置轮廓线轮廓度有或无面轮廓度有或无
位置定向
平行度有
垂直度有
倾斜度有
定位
位置度有或无
同轴（同心）度有
对称度有
跳动
圆跳动有
全跳动有
直线度(straightness)
平面度(flatness)
圆度(circularity)
圆柱度(cylindricity)
线轮廓度(profile of a line)
面轮廓度(profile of a surface)定向公差(orientation tolerance)平行度(parallelism)
垂直度(perpendicularity)
倾斜度(角度) (angularity)
位置度(position)
对称度(symmetry)
同轴度(同心度) (concentricity)圆跳动(circular runout)
全跳动(total runout)。

形位公差用语中英文对照

公差/值(tolerance/value)基本尺寸(basicsize)偏差(deviation)上/下偏差(upper/lowerdeviation)配合/间隙配合/过盈配合/过渡配合(fit/clearancefit/interferencefit/transitionfits) 单/双边公差(unilateral/bilateraltolerance)标准/精度公差(standard/precisiontolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/plane/axis)最大/小材料状态(M/LMC=maximum/leastmaterialcondition) 理论正确尺寸(theoreticalsize)基本尺寸(basicdimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profileofaline)面轮廓度(profileofasurface)定向公差(orientationtolerance)平行度(parallelism)垂直度(perpendicularity)倾斜度(角度)(angularity)位置度(position)对称度(symmetry)同轴度(同心度)(concentricity)圆跳动(circularrunout)全跳动(totalrunout)坐标尺寸(coordinatedimensioning)拔模斜度(draftangle)分型线(partingline)外圆角/内圆角拔模斜度(rounds/filletsdraft)肋材和尖角(ribandcorner)顶/测/端视图(top/side/endview)公差/值(tolerance/value)基本尺寸(basicsize)偏差(deviation)上/下偏差(upper/lowerdeviation)配合/间隙配合/过盈配合/过渡配合(fit/clearancefit/interferencefit/transitionfits) 单/双边公差(unilateral/bilateraltolerance)标准/精度公差(standard/precisiontolerance)基准/特征/点/线/平面/轴线(datum/feature/point/line/plane/axis)最大/小材料状态(M/LMC=maximum/leastmaterialcondition) 理论正确尺寸(theoreticalsize)基本尺寸(basicdimension)直径/半径(diameter/radius)直线度(straightness)平面度(flatness)圆度(circularity)圆柱度(cylindricity)线轮廓度(profileofaline)面轮廓度(profileofasurface)定向公差(orientationtolerance)平行度(parallelism)垂直度(perpendicularity)倾斜度(角度)(angularity)位置度(position)对称度(symmetry)同轴度(同心度)(concentricity)圆跳动(circularrunout)全跳动(totalrunout)坐标尺寸(coordinatedimensioning)几何尺寸(geometricdimensioning)拔模斜度(draftangle)分型线(partingline)外圆角/内圆角拔模斜度(rounds/filletsdraft)肋材和尖角(ribandcorner)顶/测/端视图(top/side/endview)加油站安全生产事故应急预案范例页脚内容。

形位公差中英文对照

形位公差中英文对照
公差符号
a b c e f g h i j d k l n o r p t m u v w x y z ` ~ ^
英文名称
GDT
a b c e f g h I j d k l n o r p t m u v w x y z ` ~ ^
中文名称
倾斜度垂直度平面度圆度平行度圆柱度跳动对称度位置度面轮廓度线轮廓度最小实体原则直径面积同轴度延伸公差带全跳动最大实体原则直线度沉孔，平底孔埋头孔，暗铆孔深度圆锥锥度斜度正负度弧長表面粗糙度
angularity perpendicularity flatness circularity(roundness) parallelism cylindricity circular runout symmetry position profile of a surface profile of a line least material condition diameter square concentricity projected tolerance total runout maximum materialcondition straightness counterbore or spotface countersink depth conical taper slope (flat taper) plus/minus degree arc length Rough
中文名稱電子秤塞尺(厚薄规) 專用量具平台百分表千分表硬度計拉壓力試驗機气动量仪游標萬能角度尺 X-光機光谱仪轮廓度仪扭力扳手油厚仪块规推拉力计游標卡尺數顯卡尺千分尺影像式顯微鏡工具顯微鏡三坐標測量機多功能測量儀電子高度儀圓弧規針規深度卡尺螺紋塞規目視粗糙度儀投影仪 Balance Thickness gage Special gage Platform Dial indicator