华为GPON配置

MA5680T与MA5620G组网1.1.1 数据规划表1数据规划1.1.2 业务配置流程1. MA5680T的数据业务配置图2MA5680T的数据业务配置流程步骤1：创建VLAN例：MA5680T(config)#vlan 1301mart 监控VLANMA5680T(config)#vlan 2 smart 用户VLAN步骤2：加入上行端口例：MA5680T(config)#port vlan 100 0/18 0 透传上行口MA5680T(config)#port vlan 1002 0/18 0步骤3：配置网管例：MA5680T(config)#interface vlanif 1301MA5680T(config-if-vlanif1301)# ip address 192.168.100.1 255.255.255.0步骤4：配置ONT管理模版及地址MA5680T(config-if-gpon-0/1 )#ont ipconfig 0 0 static ip-address 192.168.100.2mask 255.255.255.0 gateway 192.168.100.254MA5680T(config-if-gpon-0/1 )#ont port vlan 0 0 iphost 1301步骤5：配置ONT模板开局配置以后不配例：MA5680T (config)#ont-profile add{ <cr>|profile-id<K>|profile-name<K> }:profile-id{ profile-id<U><17,128> }:17{ <cr>|profile-name<K> }:Command:ont-profile add profile-id 17Press 'Q' or 'q' to quit input> Number of uplink PON ports<1-2> [1]:> IP config mode<0-Nonsupport, 1-Support, 2-DHCP only, 3-Static only> [1]:3> The type of MAC bridge<1-Single,2-Multi> [1]:1> Number of GEM ports<1-128> [32]:32> Is UNI configuration concerned<1-not concern, 2-concern> [2]:1> Mapping mode<1-VLANID, 2-802_1pPRI, 3-VLANID_802_1pPRI, 9-IPTOS, 10-VLANID_IPTOS> [1]:1> Number of T-CONTs<1-8> [1]:8> The type of flow control<1-PQ, 2-GEMPORT-CAR, 3-FLOW-CAR> [1]:3Adding an ONT profile succeededProfile-ID : 17Profile-Name : ont-profile_17步骤7：配置DBA模板例：MA5680T(config)# dba-profile add profile-id 11 type3 assure 20480{ max<K> }:max{ max-bandwidth<U><384,1235456> }:20480ONT的速率模板（11：20兆12：30兆14：）步骤8：在线增加ONT例：MA5680T(config-if-gpon-0/1# ont confirm 0 all sn-auth profile-id 17manage-mode snmp步骤9：创建Tcont模板1，并绑定DBA模版12例：MA5680T(config-if-gpon-0/1)#tcont bind-profile 0 01 profile-id 12步骤10：配置gemport例：MA5680T(config-if-gpon-0/1)# gemport add 0 gemportid 128 eth encrypt onMA5680T(config-if-gpon-0/1)# gemport add 0 gemportid 129 eth encrypt on步骤11：gemport绑定tcont例：MA5680T(config-if-gpon-0/1)#ont gemport bind 0 0 128 1 flow-carMA5680T(config-if-gpon-0/1 )#ont gemport bind 0 0 129 1 flow-car步骤12：gemport配置业务流映射例：MA5680T(config-if-gpon-0/1)#ont gemport mapping 0 0 128 vlan 1301 64 64MA5680T(config-if-gpon-0/1#ont gemport mapping 0 0 129 vlan 2 10240 10240步骤13：配置业务虚端口例：MA5680T(config)#service-port vlan 1301 gpon 0/1/0 gemport 128multi-service user-vlan 1301 inbound traffic-table index 6 outboundtraffic-table index 6（添加网管流）MA5680T(config)#service-port vlan 2 gpon 0/1/0 gemport 129multi-service user-vlan 2 inbound traffic-table index 6 outbound traffic-table index 6（添加业务流）步骤14：保存配置MA5680T(config)#save2. MA5620G的数据业务配置图3MA5620G的数据业务配置流程注：通过在OLT侧完成MDU的网管配置，即可通过OLT或网管登陆到MDU（本例为192.168.100.2）进行配置。

默认用户名：root；密码：mduadmin。

步骤1：创建业务VLAN 2例：MA5620G(config)#vlan 2步骤2：加入上行端口例：MA5620G(config)#port vlan 2 0/0 1步骤3：配置业务虚端口例：MA5620G(config)# service-port vlan 2 eth 0/1/1 user-vlan untaggedrx-cttr 6 tx-cttr 6注：此处业务虚端口为物理以太口0/1/1。

步骤4：对端口进行上行下行限速（以15 和16口为例，限3M）line-rate inbound 512 port 0/1/15line-rate outbound 3072 port 0/1/15line-rate inbound 512 port 0/1/16line-rate outbound 3072 port 0/1/16步骤5：保存配置MA5620G(config)save (保存数据)当MDU为MA5615时，其配置如下：1 .MA5616>enableMA5616#configMA5616(config)#vlan 2 smart （建立业务VLAN 2）port vlan 2 0/0 1 （透传业务VLAN 2）service-port vlan 2 adsl 0/2/1 vpi 8 vci 35 single-service rx-cttr 6 tx-cttr 6 （将业务VLAN 加到ADSL 端口）2.下面建立速率模版（下行4M）MA5616(config)#adsl line-profile add{ <cr>|profile-index<U><2,125> }:Command:adsl line-profile addStart adding profilePress 'Q' to quit the current configuration and new configuration will beneglected>Do you want to name the profile (y/n) [n]:> Please choose default value type 0-adsl 1-adsl2+ (0~1) [0]:> Will you set basic configuration for modem? (y/n)[n]:> Please select channel mode 0-interleaved 1-fast (0~1) [0]:> Will you set interleaved delay? (y/n)[n]:>Please select form of transmit rate adaptation in downstream:> 0-fixed 1-adaptAtStartup (0~1) [1]:> Will you set SNR margin for modem? (y/n)[n]:> Will you set parameters for rate? (y/n)[n]:y> Minimum transmit rate in downstream (32~8160 Kbps) [32]:128> Maximum transmit rate in downstream (128~8160 Kbps) [6144]:4096（下行4M）> Minimum transmit rate in upstream (32~896 Kbps) [32]:> Maximum transmit rate in upstream (32~896 Kbps) [640]:Add profile 3 successfully （生成的模版序号为3）3 .将3槽位的0端口用模版3激活MA5616(config)#interface adsl 0/3MA5616(config-if-adsl-0/3)#deactivate{ all<K>|portid<U><0,31> }:0Command:deactivate 0MA5616(config-if-adsl-0/3)#Deactivate port 0 successfullyMA5616(config-if-adsl-0/3)#activate 0 profile-index 3MA5616(config-if-adsl-0/3)#Send the command to activate port 0 successfullyMA5616(config-if-adsl-0/3)#MA5616(config)# save (保存数据)。