LTE事件
LTE 事件触发条件探索及其意义
LTE 事件触发条件：(一)A1触发条件：UE将发送服务小区变得比门限值更好时的测量报告，事件A1被用于UELeaving-Coverage-Alarm的监控。
进入A1的条件:Ms-hysteresis＞thresholdEutraRsrp（或者thresholdEutraRsrq）离开A1的条件:Ms+hysteresis＜thresholdEutraRsrp（或者thresholdEutraRsrq）(二)A2触发条件：UE将发送服务小区变得比门限值更坏时的测量报告，事件A2被用于UEEnter-Coverage-Alarm或者Below-Serving-Floor的监控。
进入A2的条件:Ms+hysteresis＜thresholdEutraRsrp（或者thresholdEutraRsrq）离开A2的条件:Ms-hysteresis＞thresholdEutraRsrp（或者thresholdEutraRsrq）(三)A3触发条件：UE将发送相邻小区变得比服务小区偏移更好时的测量报告，事件A3被用于如果UE不支持事件A5配置时，触发同频HO及频间重定向HO。
进入A3的条件:Mn+offset＞Ms+hysteresis，其中offset=-eventA3offset-CIO_s-offsetfreq_s+CIO_n+offsetfreq_n离开A3的条件:Mn+offset＜Ms-hysteresis，其中offset与上式相同。
(四)A4触发条件：UE将发送相邻小区比门限更好的测量报告，事件A4主要被用于ANR测量和无功率控制。
进入A4的条件Mn+offsetfreq-hysteresis ＞thresholdEutraRsrp（或者thresholdEutraRsrq）离开A4的条件Mn+offsetfreq+hysteresis ＜thresholdEutraRsrp（或者thresholdEutraRsrq）(五)A5触发条件：UE将在服务小区变得比门限值1更差且频间邻区变得比门限2更好时，发送测量报告。
LTE系统事件简介
LTE系统事件简介一、LTE事件概述LTE切换时需要UE上报测量的结果（包括RSRP，RSRQ等），而上报又分为周期性上报和事件触发的上报。
➢周期性上报由基站配置，UE直接上报测量的结果。
➢事件触发的上报又分为系统内的事件和系统间的事件。
LTE系统内切换主要事件包括：➢A1事件，服务小区质量高于门限；这个事件可以用来关闭频间测量。
➢A2事件，服务小区质量低于门限；这个事件可以用来打开频间测量和系统间测量，因为这个事件发生后可能发生切换等操作。
➢A3事件，邻小区质量好于服务小区质量；这个事件一般用于频内/间基于覆盖的切换。
➢A4事件，邻小区质量好于门限；这个事件一般用于基于负荷的切换。
➢A5事件，服务小区质量低于一个门限并且邻小区质量高于一个门限；这个事件也可以用于频内/间基于覆盖的切换。
目前LTE同频切换都是基于A3/A5事件进行的切换（现网主要是基于A3事件的）二、切换流程举例三、切换流程简要说明- RRC Connection Reconfiguration（Measurement Control）测量控制，一般在初始接入或上一次切换命令中的重配消息里携带- Measurement Report测量报告，终端根据当前小区的测量控制信息，将符合切换门限的小区进行上报- HO Request源小区在收到测量报告后向目标小区申请资源及配置信息（站内切换的话为站内交互，站间切换会使用X2口或者S1口，优先使用X2口）- HO Request Ack目标小区将终端的接纳信息以及其它配置信息反馈给源小区- RRC Connection Reconfiguration（HO Command）将目标小区的接纳信息及配置信息发给终端，告知终端目标小区已准备好终端接入，重配消息里包含目标小区的测量控制- SN Status Transfer源小区将终端业务的缓存数据移至目标小区- Random Access Preamble终端收到第5步重配消息（切换命令）后使用重配消息里的接入信息进行接入- Random Access Response目标小区接入响应，收到此命令后可认为接入完成了，然后终端在RRC层上发重配完成消息（第9步）- RRC Connect Reconfiguration complete（HO Confirm）上报重配完成消息，切换完成- Release Resource当终端成功接入后，目标小区通知源小区删除终端的上下文信息四、协议对LTE事件的定义和说明4.1 A1事件定义Event A1 (Serving becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A1-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A1-1 (Entering condition)-Ms>HysThreshInequality A1-2 (Leaving condition)Ms<+ThreshHysThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a1-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.2 A2事件定义Event A2 (Serving becomes worse than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A2-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A2-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A2-1 (Entering condition)+Ms<HysThreshInequality A2-2 (Leaving condition)Ms>-HysThreshThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a2-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.3 A3事件定义Event A3 (Neighbour becomes offset better than PCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A3-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A3-2, as specifiedbelow, is fulfilled;NOTE The cell(s) that triggers the event is on the frequency indicated in the associated measObject which may be different from the (primary) frequency used by the PCell.Inequality A3-1 (Entering condition)++>+Mn++-OcnOfpOcpMpHysOffOfnInequality A3-2 (Leaving condition)++<Mn++++MpOcpOfnOfpOffHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Mp is the measurement result of the PCell, not taking into account any offsets.Ofp is the frequency specific offset of the primary frequency (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the primary frequency).Ocp is the cell specific offset of the PCell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the primary frequency), and is set to zero if not configured for the PCell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a3-Offset as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Ofp, Ocp, Hys, Off are expressed in dB.4.4 A4事件定义Event A4 (Neighbour becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A4-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A4-2, as specifiedbelow, is fulfilled;Inequality A4-1 (Entering condition)-+Mn>+HysThreshOcnOfnInequality A4-2 (Leaving condition)Mn<+++ThreshOfnHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a4-Threshold as defined within reportConfigEUTRA for this event).Mn is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.5 A5事件定义Event A5 (PCell becomes worse than threshold1 and neighbour becomes better than threshold2)The UE shall:1> consider the entering condition for this event to be satisfied when both condition A5-1 andcondition A5-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition A5-3 or condition A5-4, i.e. at least one of the two, as specified below, is fulfilled;NOTE: The cell(s) that triggers the event is on the frequency indicated in the associatedmeasObject which may be different from the (primary) frequency used by the PCell.Inequality A5-1 (Entering condition 1)1Thresh Hys Mp <+Inequality A5-2 (Entering condition 2)2Thresh Hys Ocn Ofn Mn >-++Inequality A5-3 (Leaving condition 1)1Thresh Hys Mp >-Inequality A5-4 (Leaving condition 2)2Thresh Hys Ocn Ofn Mn <+++The variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh1 is the threshold parameter for this event (i.e. a5-Threshold1 as defined within reportConfigEUTRA for this event).Thresh2 is the threshold parameter for this event (i.e. a5-Threshold2 as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh1 is expressed in the same unit as Mp .Thresh2 is expressed in the same unit as Mn .Event A6 (Neighbour becomes offset better than SCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A6-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A6-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the (secondary) cell that is configured on the frequency indicatedin the associated measObjectEUTRA to be the serving cell;NOTE: The neighbour(s) is on the same frequency as the SCell i.e. both are on the frequency indicated in the associated measObject.Inequality A6-1 (Entering condition)+>Mn++-MsOcsOffHysOcnInequality A6-2 (Leaving condition)+<+Mn++OcsOffMsHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Ms is the measurement result of the serving cell, not taking into account any offsets.Ocs is the cell specific offset of the serving cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the serving frequency), and is set to zero if not configured for the serving cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a6-Offset as defined within reportConfigEUTRA for this event).Mn, Ms are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ocn, Ocs, Hys, Off are expressed in dB.Event B1 (Inter RAT neighbour becomes better than threshold)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when condition B1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition B1-2, as specifiedbelow, is fulfilled;Inequality B1-1 (Entering condition)Thresh+Mn>-HysOfnInequality B1-2 (Leaving condition)++Mn<ThreshHysOfnThe variables in the formula are defined as follows:Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA 2000 measurement result, pilotStrength is divided by -2.Ofn is the frequency specific offset of the frequency of the inter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the neighbour inter-RAT cell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh is the threshold parameter for this event (i.e. b1-Threshold as defined within reportConfigInterRAT for this event). For CDMA2000, b1-Threshold is divided by -2.Mn is expressed in dBm or in dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.8 B2事件定义Event B2 (PCell becomes worse than threshold1 and inter RAT neighbour becomes better than threshold2)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when both condition B2-1 andcondition B2-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition B2-3 or conditionB2-4, i.e. at least one of the two, as specified below, is fulfilled;Inequality B2-1 (Entering condition 1)+HysMp<Thresh1Inequality B2-2 (Entering condition 2)-+Mn>Ofn2ThreshHysInequality B2-3 (Leaving condition 1)Hys-Mp>1ThreshInequality B2-4 (Leaving condition 2)Mn<++OfnHys2ThreshThe variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA2000 measurement result, pilotStrength is divided by -2.Ofn is the frequency specific offset of the frequency of the inter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the inter-RAT neighbourcell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh1 is the threshold parameter for this event (i.e. b2-Threshold1 as defined within reportConfigInterRAT for this event).Thresh2 is the threshold parameter for this event (i.e. b2-Threshold2 as defined within reportConfigInterRAT for this event). For CDMA2000, b2-Threshold2 is divided by -2.Mp is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Mn is expressed in dBm or dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.修正版Thresh1 is expressed in the same unit as Mp. Thresh2 is expressed in the same unit as Mn.。
A1-B2事件
LTE支持的切换事件有A类和B类，其中A类本用作系统内测量，B类被用作系统间测量A1事件：表示服务小区信号质量高于一定门限；A2事件：表示服务小区信号质量低于一定门限；A3事件：表示邻区质量高于服务小区质量，用于同频、异频的基于覆盖的切换； A4事件：表示邻区质量高于一定门限，用于基于负荷的切换，可用于负载均衡；A5事件：表示服务小区质量低于一定门限并且邻区质量高于一定门限，可用于负载均衡; 异系统测量事件：B1事件：邻小区质量高于一定门限，用于测量高优先级的异系统小区；B2事件：服务小区质量低于一定门限，并且邻小区质量高于一定门限，用于相同或较低优先级的异系统小区的测量。
LTE移动性参数(全局)最小接入电平基本信息参数功能该参数表示UE在该小区驻留需满足的最小接收电平门限。
该值取值范围是2G/3G接收电平的实际值，对于LTE/3G , 实际的RxlevMin 等于SIB3/SIB6的IE value的两倍，调整步长为2dbm。
对于2G，实际的RxlevMin等于SIB7的(IE value * 2) - 115，调整步长为2dBm当UE测量到的2G/3G电平满足S准则时，UE才可能驻留在该小区。
参数调整影响调整该参数的门限值，会对小区的选择和驻留有所影响。
QrxLevMin如果设置过高，则UE将无法驻留到该小区。
2高优先级重选门限基本信息参数功能当高优先级小区的S值在一定时间内高于该阀值(threshXHigh)后，UE可以重选到该小区。
参数调整影响调整该参数的门限值，会对小区的选择和驻留有所影响。
threshXhigh如果设置过高，会增加UE重选到高优先级小区的难度。
3低优先级重选门限基本信息参数功能当低优先级小区的S值在一定时间内高于该阀值(threshXLow)后，同时主服务小区的S值低于threshServingLow，UE可以重选到该低优先级小区。
参数调整影响调整该参数的门限值，会对小区的选择和驻留有所影响。
LTE事件解释18页
1 4.5.1 切换正常流程同频切换同时支持同eNodeB切换，同MME的异eNodeB切换，跨MME的异eNodeB切换场景。
对于后两种场景依据eNodeB间是否建立X2接口，切换信令流程略有不同。
图4-2 同MME异eNodeB间切换流程同MME异eNodeB间的同频切换信令流程如图4-2所示：1. 在无线承载建立时，源eNodeB下发RRC ConnectionReconfiguration至UE，其中包含source eNodeB 配置的Measurement Configuration消息，用于控制UE连接态的测量过程。
2. UE根据测量结果上报Measurement Report。
3. 源eNodeB根据测量报告进行切换决策。
4. 当源eNodeB决定切换后，源eNodeB发出HandoverRequest消息给目标eNodeB，通知目标eNodeB准备切换。
5. 目标eNodeB进行准入判断，若判断为资源准入，再由目标eNodeB依据EPS的QoS信息执行准入控制。
6. 目标eNodeB在L1/L2准备切换并对源eNodeB发送HANDOVERREQUEST ACKNOWLEDGE消息。
3.1.2 报告配置事件触发上报是3GPP 36.331协议中为切换测量与判决定义的一个概念。
报告配置包含相应事件的相关参数。
目前eNodeB应用以下事件触发相应动作：事件A1表示服务小区质量高于一定门限，当满足事件触发条件时UE便上报测量报告，eNodeB停止异频/异系统测量。
但在基于频率优先级的切换中，事件A1用于启动异频测量。
事件A2表示服务小区质量低于一定门限，当满足事件触发条件时UE便上报测量报告，eNodeB启动异频/异系统测量。
但在基于频率优先级的切换中，事件A2用于停止异频测量。
事件A3表示同频/异频邻区质量相比服务小区质量高出一定门限，当满足事件触发条件的小区信息被上报时，源eNodeB启动同频/异频切换请求。
LTE切换事件介绍
Ocn：邻小区个性偏移（CIO）
Hys(5)：A5事件迟滞参数 Thersh1:A5事件门限1参数 Thersh2:A5事件门限2参数
B1事件的切换参数配置
B1事件表示：异系统邻区质量高于一个绝对门限，满足事件触发条件的小 区信息被上报时，源eNodeB启动异系统切换请求，用于基于负荷的切换 B1事件判决公式： 触发条件： Mn + Ofn - Hys(b1) > Thersh(b1) 取消条件：Mn + Ofn + Hys(b1) > Thersh(b1) 其中： Mn:邻小区测量结果 Ofn：邻小区频率特定的偏差，默认为0
根据A1事件触发条件：Ms – Hys(1) > Thersh(1）可以算出： Ms>-86时关闭异频测量。 根据A2事件触发条件：Ms + Hys(2) < Thersh(2) 可以算出： Ms<-92时开启异频测量 则当UE测量到的A小区RSRP值为红色区域时，UE不进行异频测量；当 UE测量到的A小区RSRP值为绿色区域时，UE进行异频测量；当UE测量到的A 小区RSRP值为黄色区域时，UE是否进行异频测量取决于UE之前的状态，即 UE的测量状态并不改变。
频内/频间基于覆盖的切换 B1事件：异系统邻区质量高于一个绝对门限，用于基于负荷的切换。
B2事件：服务小区质量低于一个绝对门限1且异系统邻区质量高于一个绝对门限2，
用于基于覆盖的切换。
A1事件的切换参数配置
A1事件触发条件：Ms – Hys(1) > Thersh(1） A1事件取消条件：Ms + Hys(2) < Thersh(2) 其中： Ms:服务小区测量结果 Hys(1)：A1事件迟滞参数 Hys(2)：A2事件迟滞参数 Thersh（1）:A1事件门限参数 Thersh（2）:A2事件门限参数
AB事件LTE
LTE 支持的切换事件有A 类和B 类，其中A 类本用作系统内测量，B 类被用作系统间测量A1事件：表示服务小区信号质量高于一定门限； A2事件：表示服务小区信号质量低于一定门限；A3事件：表示邻区质量高于服务小区质量，用于同频、异频的基于覆盖的切换； A4事件：表示邻区质量高于一定门限，用于基于负荷的切换，可用于负载均衡；A5事件：表示服务小区质量低于一定门限并且邻区质量高于一定门限，可用于负载均衡; 异系统测量事件： B1事件：邻小区质量高于一定门限，用于测量高优先级的异系统小区；B2事件：服务小区质量低于一定门限，并且邻小区质量高于一定门限，用于相同或较低优先级的异系统小区的测量。
LTE 移动性参数(全局)最小接入电平基本信息参数功能该参数表示UE 在该小区驻留需满足的最小接收电平门限。
该值取值范围是2G/3G 接收电平的实际值，对于LTE/3G ,?实际的RxlevMin?等于SIB3/SIB6的IE value 的两倍，调整步长为2dbm 。
对于2G ，实际的RxlevMin 等于SIB7的?(IE value * 2)? ?115，调整步长为2dBm 当UE 测量到的2G/3G 电平满足S 准则时，UE 才可能驻留在该小区。
参数调整影响调整该参数的门限值，会对小区的选择和驻留有所影响。
QrxLevMin 如果设置过高，则UE 将无法驻留到该小区。
高优先级重选门限基本信息参数功能当高优先级小区的S值在一定时间内高于该阀值(threshXHigh)后，UE可以重选到该小区。
参数调整影响调整该参数的门限值，会对小区的选择和驻留有所影响。
threshXhigh如果设置过高，?会增加UE重选到高优先级小区的难度。
低优先级重选门限基本信息参数功能当低优先级小区的S值在一定时间内高于该阀值(threshXLow)后，同时主服务小区的S值低于threshServingLow，UE可以重选到该低优先级小区。
移动LTE系统事件介绍
LTE系统事件介绍一、LTE事件概述LTE切换时需要UE上报测量的结果（包括RSRP，RSRQ等），而上报又分为周期性上报和事件触发的上报。
周期性上报由基站配置，UE直接上报测量的结果。
事件触发的上报又分为系统内的事件和系统间的事件。
LTE系统内切换主要事件包括：A1事件，服务小区质量高于门限；这个事件可以用来关闭频间测量。
A2事件，服务小区质量低于门限；这个事件可以用来打开频间测量和系统间测量，因为这个事件发生后可能发生切换等操作。
A3事件，邻小区质量好于服务小区质量；这个事件一般用于频内/间基于覆盖的切换。
A4事件，邻小区质量好于门限；这个事件一般用于基于负荷的切换。
A5事件，服务小区质量低于一个门限并且邻小区质量高于一个门限；这个事件也可以用于频内/间基于覆盖的切换。
目前LTE同频切换都是基于A3/A5事件进行的切换（现网主要是基于A3事件的）二、切换流程举例- RRC Connection Reconfiguration（Measurement Control）测量控制，一般在初始接入或上一次切换命令中的重配消息里携带- Measurement Report测量报告，终端根据当前小区的测量控制信息，将符合切换门限的小区进行上报- HO Request源小区在收到测量报告后向目标小区申请资源及配置信息（站内切换的话为站内交互，站间切换会使用X2口或者S1口，优先使用X2口）- HO Request Ack目标小区将终端的接纳信息以及其它配置信息反馈给源小区- RRC Connection Reconfiguration（HO Command）将目标小区的接纳信息及配置信息发给终端，告知终端目标小区已准备好终端接入，重配消息里包含目标小区的测量控制- SN Status Transfer源小区将终端业务的缓存数据移至目标小区- Random Access Preamble终端收到第5步重配消息（切换命令）后使用重配消息里的接入信息进行接入- Random Access Response目标小区接入响应，收到此命令后可认为接入完成了，然后终端在RRC层上发重配完成消息（第9步）- RRC Connect Reconfiguration complete（HO Confirm）上报重配完成消息，切换完成- Release Resource当终端成功接入后，目标小区通知源小区删除终端的上下文信息四、协议对LTE事件的定义和说明4.1 A1事件定义Event A1 (Serving becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A1-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A1-1 (Entering condition)-Ms>HysThreshInequality A1-2 (Leaving condition)Ms<+ThreshHysThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a1-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.2 A2事件定义Event A2 (Serving becomes worse than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A2-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A2-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A2-1 (Entering condition)+Ms<HysThreshInequality A2-2 (Leaving condition)Ms>-HysThreshThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a2-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.3 A3事件定义Event A3 (Neighbour becomes offset better than PCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A3-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A3-2, as specifiedbelow, is fulfilled;NOTE The cell(s) that triggers the event is on the frequency indicated in the associated measObject which may be different from the (primary) frequency used by the PCell.Inequality A3-1 (Entering condition)++>+Mn++-OcnOfpOcpMpHysOffOfnInequality A3-2 (Leaving condition)++<Mn++++MpOcpOfnOfpOffHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Mp is the measurement result of the PCell, not taking into account any offsets.Ofp is the frequency specific offset of the primary frequency (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the primary frequency).Ocp is the cell specific offset of the PCell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the primary frequency), and is set to zero if not configured for the PCell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a3-Offset as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Ofp, Ocp, Hys, Off are expressed in dB.4.4 A4事件定义Event A4 (Neighbour becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A4-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A4-2, as specifiedbelow, is fulfilled;Inequality A4-1 (Entering condition)-+Mn>+HysThreshOcnOfnInequality A4-2 (Leaving condition)Mn<+++ThreshOfnHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a4-Threshold as defined within reportConfigEUTRA for this event).Mn is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.5 A5事件定义Event A5 (PCell becomes worse than threshold1 and neighbour becomes better than threshold2)The UE shall:1> consider the entering condition for this event to be satisfied when both condition A5-1 andcondition A5-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition A5-3 or conditionA5-4, i.e. at least one of the two, as specified below, is fulfilled;NOTE: The cell(s) that triggers the event is on the frequency indicated in the associated measObject which may be different from the (primary) frequency used by the PCell.Inequality A5-1 (Entering condition 1)+Mp<HysThresh1Inequality A5-2 (Entering condition 2)+-+Mn>Thresh2HysOcnOfnInequality A5-3 (Leaving condition 1)-Mp>HysThresh1Inequality A5-4 (Leaving condition 2)2++Mn<+OfnHysThreshOcnThe variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigEUTRA for this event).Thresh1 is the threshold parameter for this event (i.e. a5-Threshold1 as defined within reportConfigEUTRA for this event).Thresh2 is the threshold parameter for this event (i.e. a5-Threshold2 as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh1is expressed in the same unit as Mp.Thresh2is expressed in the same unit as Mn.Event A6 (Neighbour becomes offset better than SCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A6-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A6-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the (secondary) cell that is configured on the frequency indicatedin the associated measObjectEUTRA to be the serving cell;NOTE: The neighbour(s) is on the same frequency as the SCell i.e. both are on the frequency indicated in the associated measObject.Inequality A6-1 (Entering condition)+>Mn++-MsOcsOffHysOcnInequality A6-2 (Leaving condition)+<+Mn++OcsOffMsHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Ms is the measurement result of the serving cell, not taking into account any offsets.Ocs is the cell specific offset of the serving cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the serving frequency), and is set to zero if not configured for the serving cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a6-Offset as defined within reportConfigEUTRA for this event).Mn, Ms are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ocn, Ocs, Hys, Off are expressed in dB.Event B1 (Inter RAT neighbour becomes better than threshold)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when condition B1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition B1-2, as specifiedbelow, is fulfilled;Inequality B1-1 (Entering condition)Thresh+Mn>-HysOfnInequality B1-2 (Leaving condition)++Mn<ThreshHysOfnThe variables in the formula are defined as follows:Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA 2000 measurement result, pilotStrength is divided by -2.Ofn is the frequency specific offset of the frequency of the inter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the neighbour inter-RAT cell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh is the threshold parameter for this event (i.e. b1-Threshold as defined within reportConfigInterRAT for this event). For CDMA2000, b1-Threshold is divided by -2.Mn is expressed in dBm or in dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.8 B2事件定义Event B2 (PCell becomes worse than threshold1 and inter RAT neighbour becomes better than threshold2)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when both condition B2-1 andcondition B2-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition B2-3 or conditionB2-4, i.e. at least one of the two, as specified below, is fulfilled;Inequality B2-1 (Entering condition 1)+HysMp<Thresh1Inequality B2-2 (Entering condition 2)-+Mn>Ofn2ThreshHysInequality B2-3 (Leaving condition 1)Hys-Mp>1ThreshInequality B2-4 (Leaving condition 2)Mn<++OfnHys2ThreshThe variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA2000 measurement result, pilotStrength is divided by -2.Ofn is the frequency specific offset of the frequency of the inter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the inter-RAT neighbourcell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh1 is the threshold parameter for this event (i.e. b2-Threshold1 as defined within reportConfigInterRAT for this event).Thresh2 is the threshold parameter for this event (i.e. b2-Threshold2 as defined within reportConfigInterRAT for this event). For CDMA2000, b2-Threshold2 is divided by -2.Mp is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Mn is expressed in dBm or dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.Thresh1is expressed in the same unit as Mp.Thresh2is expressed in the same unit as Mn.第11页。
LTE事件
LTE切换时需要UE上报测量的结果（包括RSRP，RSRQ等），而上报又分为周期性上报和事件触发的上报。
周期性上报由基站配置，UE直接上报测量的结果。
事件触发的上报又分为同频系统的事件和不同系统间的事件：同频切换报告事件包括：
1. 事件A1，服务小区好于绝对门限；这个事件可以用来关闭某些小区间的测量。
2. 事件A2，服务小区差于绝对门限；这个事件可以用来开启某些小区间的测量，因为这个事件发生后可能发生切换等操作。
3. 事件A3，邻居小区好于服务小区；这个事件发生可以用来决定UE是否切换到邻居小区。
4. 事件A4，邻居小区好于绝对门限；
5. 事件A5，服务小区差于一个绝对门限并且邻居小区好于一个绝对门限；这个事件也可以用来支持切换
Event B1(Inter RAT neighbour becomes better than threshold)：表示异系统邻区质量高于一定门限，满足此条件事件被上报时，源eNodeB启动异系统切换请求；类似于UMTS的3C事件。
Event B2(Serving becomes worse than threshold1 and inter RAT neighbour becomes better than threshold2)：表示服务小区质量低于一定门限并且异系统邻区质量高于一定门限，类似于UMTS的3A事件。
LTE系统事件简介
LTE系统事件简介LTE系统事件简介一、LTE事件概述LTE切换时需要UE上报测量的结果（包括RSRP，RSRQ等），而上报又分为周期性上报和事件触发的上报。
周期性上报由基站配置，UE直接上报测量的结果。
事件触发的上报又分为系统内的事件和系统间的事件。
LTE系统内切换主要事件包括：A1事件，服务小区质量高于门限；这个事件可以用来关闭频间测量。
A2事件，服务小区质量低于门限；这个事件可以用来打开频间测量和系统间测量，因为这个事件发生后可能发生切换等操作。
A3事件，邻小区质量好于服务小区质量；这个事件一般用于频内/间基于覆盖的切换。
A4事件，邻小区质量好于门限；这个事件一般用于基于负荷的切换。
A5事件，服务小区质量低于一个门限并且邻小区质量高于一个门限；这个事件也可以用于频内/间基于覆盖的切换。
目前LTE同频切换都是基于A3/A5事件进行的切换（现网主要是基于A3事件的）二、切换流程举例三、切换流程简要说明- RRC Connection Reconfiguration（Measurement Control）测量控制，一般在初始接入或上一次切换命令中的重配消息里携带- Measurement Report测量报告，终端根据当前小区的测量控制信息，将符合切换门限的小区进行上报- HO Request源小区在收到测量报告后向目标小区申请资源及配置信息（站内切换的话为站内交互，站间切换会使用X2口或者S1口，优先使用X2口）- HO Request Ack目标小区将终端的接纳信息以及其它配置信息反馈给源小区- RRC Connection Reconfiguration（HO Command）将目标小区的接纳信息及配置信息发给终端，告知终端目标小区已准备好终端接入，重配消息里包含目标小区的测量控制- SN Status Transfer源小区将终端业务的缓存数据移至目标小区- Random Access Preamble终端收到第5步重配消息（切换命令）后使用重配消息里的接入信息进行接入- Random Access Response目标小区接入响应，收到此命令后可认为接入完成了，然后终端在RRC层上发重配完成消息（第9步）- RRC Connect Reconfiguration complete（HO Confirm）上报重配完成消息，切换完成- Release Resource当终端成功接入后，目标小区通知源小区删除终端的上下文信息四、协议对LTE事件的定义和说明4.1 A1事件定义Event A1 (Serving becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A1-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A1-1 (Entering condition)-Ms>HysThreshInequality A1-2 (Leaving condition)Ms<+ThreshHysThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a1-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.2 A2事件定义Event A2 (Serving becomes worse than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A2-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A2-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the primary or secondary cell that is configured on the frequencyindicated in the associated measObjectEUTRA to be the serving cell;Inequality A2-1 (Entering condition)+Ms<HysThreshInequality A2-2 (Leaving condition)Ms>-HysThreshThe variables in the formula are defined as follows:Ms is the measurement result of the serving cell, not taking into account any offsets.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a2-Threshold as defined within reportConfigEUTRA for this event).Ms is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Hys is expressed in dB.Thresh is expressed in the same unit as Ms.4.3 A3事件定义Event A3 (Neighbour becomes offset better than PCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A3-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A3-2, as specifiedbelow, is fulfilled;NOTE The cell(s) that triggers the event is on the frequency indicated in the associated measObject which may be different from the (primary) frequency used by the PCell.Inequality A3-1 (Entering condition)++>+Mn++-OcnOfpOcpMpHysOffOfnInequality A3-2 (Leaving condition)++<Mn++++MpOcpOfnOfpOffHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Mp is the measurement result of the PCell, not taking into account any offsets.Ofp is the frequency specific offset of the primary frequency (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the primary frequency).Ocp is the cell specific offset of the PCell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the primary frequency), and is set to zero if not configured for the PCell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a3-Offset as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Ofp, Ocp, Hys, Off are expressed in dB.4.4 A4事件定义Event A4 (Neighbour becomes better than threshold)The UE shall:1> consider the entering condition for this event to be satisfied when condition A4-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A4-2, as specifiedbelow, is fulfilled;Inequality A4-1 (Entering condition)-+Mn>+HysThreshOcnOfnInequality A4-2 (Leaving condition)Mn<+++ThreshOfnHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh is the threshold parameter for this event (i.e. a4-Threshold as defined within reportConfigEUTRA for this event).Mn is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.5 A5事件定义Event A5 (PCell becomes worse than threshold1 and neighbour becomes better than threshold2)The UE shall:1> consider the entering condition for this event to be satisfied when both condition A5-1 andcondition A5-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition A5-3 or condition A5-4, i.e. at least one of the two, as specified below, is fulfilled;NOTE: The cell(s) that triggers the event is on the frequency indicated in the associatedmeasObject which may be different from the (primary) frequency used by the PCell.Inequality A5-1 (Entering condition 1)1Thresh Hys Mp <+Inequality A5-2 (Entering condition 2)2Thresh Hys Ocn Ofn Mn >-++Inequality A5-3 (Leaving condition 1)1Thresh Hys Mp >-Inequality A5-4 (Leaving condition 2)2Thresh Hys Ocn Ofn Mn <+++The variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ofn is the frequency specific offset of the frequency of the neighbour cell (i.e. offsetFreq as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell).Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Thresh1 is the threshold parameter for this event (i.e. a5-Threshold1 as defined within reportConfigEUTRA for this event).Thresh2 is the threshold parameter for this event (i.e. a5-Threshold2 as defined within reportConfigEUTRA for this event).Mn, Mp are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ofn, Ocn, Hys are expressed in dB.Thresh1 is expressed in the same unit as Mp .Thresh2 is expressed in the same unit as Mn .Event A6 (Neighbour becomes offset better than SCell)The UE shall:1> consider the entering condition for this event to be satisfied when condition A6-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition A6-2, as specifiedbelow, is fulfilled;1> for this measurement, consider the (secondary) cell that is configured on the frequency indicatedin the associated measObjectEUTRA to be the serving cell;NOTE: The neighbour(s) is on the same frequency as the SCell i.e. both are on the frequency indicated in the associated measObject.Inequality A6-1 (Entering condition)+>Mn++-MsOcsOffHysOcnInequality A6-2 (Leaving condition)+<+Mn++OcsOffMsHysOcnThe variables in the formula are defined as follows:Mn is the measurement result of the neighbouring cell, not taking into account any offsets.Ocn is the cell specific offset of the neighbour cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the frequency of the neighbour cell), and set to zero if not configured for the neighbour cell.Ms is the measurement result of the serving cell, not taking into account any offsets.Ocs is the cell specific offset of the serving cell (i.e. cellIndividualOffset as defined within measObjectEUTRA corresponding to the serving frequency), and is set to zero if not configured for the serving cell.Hys is the hysteresis parameter for this event (i.e. hysteresis as defined within reportConfigEUTRA for this event).Off is the offset parameter for this event (i.e. a6-Offset as defined within reportConfigEUTRA for this event).Mn, Ms are expressed in dBm in case of RSRP, or in dB in case of RSRQ.Ocn, Ocs, Hys, Off are expressed in dB.Event B1 (Inter RAT neighbour becomes better than threshold)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when condition B1-1, as specifiedbelow, is fulfilled;1> consider the leaving condition for this event to be satisfied when condition B1-2, as specifiedbelow, is fulfilled;Inequality B1-1 (Entering condition)Thresh+Mn>-HysOfnInequality B1-2 (Leaving condition)++Mn<ThreshHysOfnThe variables in the formula are defined as follows:Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA 2000 measurement result, pilotStrength is divided by -2.Ofn is the frequency specific offset of the frequency of theinter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the neighbour inter-RAT cell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh is the threshold parameter for this event (i.e. b1-Threshold as defined within reportConfigInterRAT for this event). For CDMA2000, b1-Threshold is divided by -2.Mn is expressed in dBm or in dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.Thresh is expressed in the same unit as Mn.4.8 B2事件定义Event B2 (PCell becomes worse than threshold1 and inter RAT neighbour becomes better than threshold2)The UE shall:1> for UTRA and CDMA2000, only trigger the event for cells included in the correspondingmeasurement object;1> consider the entering condition for this event to be satisfied when both condition B2-1 andcondition B2-2, as specified below, are fulfilled;1> consider the leaving condition for this event to be satisfied when condition B2-3 or conditionB2-4, i.e. at least one of the two, as specified below, is fulfilled;Inequality B2-1 (Entering condition 1)+HysMp<Thresh1Inequality B2-2 (Entering condition 2)-+Mn>Ofn2ThreshHysInequality B2-3 (Leaving condition 1)Hys-Mp>1ThreshInequality B2-4 (Leaving condition 2)Mn<++OfnHys2ThreshThe variables in the formula are defined as follows:Mp is the measurement result of the PCell, not taking into account any offsets.Mn is the measurement result of the inter-RAT neighbour cell, not taking into account any offsets.For CDMA2000 measurement result, pilotStrength is dividedby -2.Ofn is the frequency specific offset of the frequency of the inter-RAT neighbour cell (i.e. offsetFreq as defined within the measObject corresponding to the frequency of the inter-RAT neighbourcell).Hys is the hysteresis parameter for this event (i.e. hysteresis as defined withinreportConfigInterRAT for this event).Thresh1 is the threshold parameter for this event (i.e. b2-Threshold1 as defined within reportConfigInterRAT for this event).Thresh2 is the threshold parameter for this event (i.e. b2-Threshold2 as defined within reportConfigInterRAT for this event). For CDMA2000, b2-Threshold2 is divided by -2.Mp is expressed in dBm in case of RSRP, or in dB in case of RSRQ.Mn is expressed in dBm or dB, depending on the measurement quantity of the inter-RAT neighbour cell.Ofn, Hys are expressed in dB.Thresh1 is expressed in the same unit as Mp. Thresh2 is expressed in the same unit as Mn.。
lte连接态a1事件计算方法
lte连接态a1事件计算方法
LTE连接态A1事件计算方法是一种用于计算LTE网络中UE（用户终端设备）与基站之间的连接状态的方法。
该方法主要用于确定UE是否需要在特定的情况下进行连接和维持连接。
以下是一种常见的LTE连接态A1事件计算方法：
1. 确定A1事件的触发条件：A1事件通常与UE的信号强度和基站的信号质量相关。
触发A1事件的条件可以是UE的信号强度低于某个阈值，或者基站的信号质量低于某个阈值。
2. 确定A1事件的触发动作：一旦A1事件被触发，UE需要执行相应的动作来处理连接状态。
这些动作可以包括重新选择更好的基站进行连接，或者保持当前的连接状态。
3. 定义A1事件的计算方法：为了计算A1事件的触发条件，可以使用一些信号参数和门限值来进行计算。
这些参数可以包括UE的信号强度、基站的信号质量、门限值等。
4. 实施A1事件的触发和动作：一旦A1事件的触发条件满足，UE 需要执行相应的动作来处理连接状态。
这些动作可以通过与基站进行通信来实现。
需要注意的是，LTE连接态A1事件的计算方法可以根据具体的网络需求和实际情况进行调整和优化。
此外，还可以结合其他的事件和算法来进一步提高连接状态的性能和效率。
A1-B2事件 (LTE)
LTE支持的切换事件有A类和B类，其中A类本用作系统内测量，B类被用作系统间测量A1事件：表示服务小区信号质量高于一定门限；A2事件：表示服务小区信号质量低于一定门限；A3事件：表示邻区质量高于服务小区质量，用于同频、异频的基于覆盖的切换；A4事件：表示邻区质量高于一定门限，用于基于负荷的切换，可用于负载均衡；A5事件：表示服务小区质量低于一定门限并且邻区质量高于一定门限，可用于负载均衡; 异系统测量事件：B1事件：邻小区质量高于一定门限，用于测量高优先级的异系统小区；B2事件：服务小区质量低于一定门限，并且邻小区质量高于一定门限，用于相同或较低优先级的异系统小区的测量。
LTE移动性参数(全局)1最小接入电平基本信息参数名称(中文)参数名称(英文)取值范围单位最小接收电平QrxLevMin LTE (-140 (44)3G (-119 (25)2G (-115 (25)dBm缺省值开局建议值配置步长参数类型LTE:-1403G邻区频点:-119 2G邻区频点:-115LTE:-1223G:-1192G:-1152长整型影响范围修改生效方式参数出处适用制式LTE小区2G/3G邻区频点修改立即生效3GPP TS 36.331通用参数功能该参数表示UE在该小区驻留需满足的最小接收电平门限。
该值取值范围是2G/3G接收电平的实际值，对于LTE/3G , 实际的RxlevMin 等于SIB3/SIB6的IE value的两倍，调整步长为2dbm。
对于2G，实际的RxlevMin等于SIB7的 (IE value * 2) 115，调整步长为2dBm当UE测量到的2G/3G电平满足S准则时，UE才可能驻留在该小区。
参数调整影响调整该参数的门限值，会对小区的选择和驻留有所影响。
QrxLevMin如果设置过高，则UE将无法驻留到该小区。
2高优先级重选门限基本信息参数功能当高优先级小区的S值在一定时间内高于该阀值(threshXHigh)后，UE可以重选到该小区。
LTE基本事件汇总表
U E收到Deactivate Eps Bearer Context Request消息后，收到了RRC Con 以下情况表示ERAB正常释放：如果第k条和第k+1条切换A3事件时间小于1s，且之间没有切换命令，统计为一次HOPrepareAttempt。
如果第k条和第k+1条切换A3事件时间小于1s，且之间有切换命令，切换准备尝试次数+1。
据业务成功。
示附着数据业务失败。
基站向UE发送Detach Request消息后，在15秒内收到UE发出的De 后，在15秒内收到基站发出的Detach Accept消息。
p Complete，则触发该事件。
Setup Complete，或者收到RRC Connection Reject，则触发该事件。
ddModList”或“drb-ToAddModifyList”），并且不包含信元“mobilityControlInfo”，表示ERAB建立尝试。
ration Complete消息，并且消息中的信元“RRC-TransactionIdentifier”值与信元“RRC Connection ReconfiguE RABSetupAttempt事件发生后，UE收到RRCConnectionRees 收到RRC Connection Reconfiguration Complete消息。
U E收到Dea uest消息后，收到了RRC Connection Reconfiguration消息，且消息中有信元“drb-ToReleaseList”。
REQUEST消息和MME的DETACH REQUEST消息，也没有向网络侧主动发出DETACH REQUEST消息，但收到了RRCConnecti到UE发出的Detach Accept消息示ERAB建立尝试。
onnection Reconfiguration”信元值相同，则表示ERAB建立成功。
到RRCConnectionReestablishmentRequest消息。
LTE事件分析详解
U E收到Deactivate Eps Bearer Context Request消息后，收到了RRC Con 以下情况表示ERAB正常释放：如果第k条和第k+1条切换A3事件时间小于1s，且之间没有切换命令，统计为一次HOPrepareAttempt。
如果第k条和第k+1条切换A3事件时间小于1s，且之间有切换命令，切换准备尝试次数+1。
据业务成功。
示附着数据业务失败。
基站向UE发送Detach Request消息后，在15秒内收到UE发出的De 后，在15秒内收到基站发出的Detach Accept消息。
p Complete，则触发该事件。
Setup Complete，或者收到RRC Connection Reject，则触发该事件。
ddModList”或“drb-ToAddModifyList”），并且不包含信元“mobilityControlInfo”，表示ERAB建立尝试。
ration Complete消息，并且消息中的信元“RRC-TransactionIdentifier”值与信元“RRC Connection ReconfiguE RABSetupAttempt事件发生后，UE收到RRCConnectionRees 收到RRC Connection Reconfiguration Complete消息。
U E收到Dea uest消息后，收到了RRC Connection Reconfiguration消息，且消息中有信元“drb-ToReleaseList”。
REQUEST消息和MME的DETACH REQUEST消息，也没有向网络侧主动发出DETACH REQUEST消息，但收到了RRCConnecti到UE发出的Detach Accept消息示ERAB建立尝试。
onnection Reconfiguration”信元值相同，则表示ERAB建立成功。
到RRCConnectionReestablishmentRequest消息。
lte b2事件计算公式
lte b2事件计算公式
LTE（Long Term Evolution）是一种无线通信技术，而LTE B2
是指LTE频段2。
在LTE系统中，事件计算公式用于计算特定事件
的发生概率或其他相关参数。
然而，LTE B2事件计算公式的具体内
容取决于所要计算的具体事件。
一般来说，LTE系统中的事件计算
公式涉及到信道容量、传输速率、信噪比、干扰等参数。
对于LTE B2频段的事件计算公式，可以从以下几个角度来考虑：
1. 信道容量，事件计算公式可能涉及到LTE B2频段的信道容量，即在特定条件下该频段能够支持的最大数据传输速率。
这可能
涉及到符号速率、码率、调制方式等参数，可以通过信道容量公式
来计算。
2. 信噪比，LTE B2频段的事件计算公式可能与信噪比有关，
即在特定信噪比条件下，特定事件发生的概率或性能参数。
这可能
涉及到误码率、误比特率等指标的计算公式。
3. 干扰，在LTE系统中，干扰是一个重要的问题，特别是在频
谱拥挤的情况下。
因此，LTE B2频段的事件计算公式可能涉及到干
扰的计算和分析，包括与相邻频段的干扰、同频干扰等相关的公式
和参数。
综上所述，LTE B2事件计算公式涉及到多个方面的参数和条件，需要根据具体的事件和情境来进行计算和分析。
在实际应用中，工
程师们会根据具体的需求和情况来选择合适的公式进行计算和分析，以确保LTE系统的性能和可靠性。
LTE常见事件以及解析
名称含义具体说明AttachAttempt 附着尝试 UE发送Attach Request消息请求附着到数据业务。
AttachSuc 附着成功 UE发送Attach Request消息后，在45秒内发送Attach Complete消息，表示附着数据业务成功。
AttachFail 附着失败 UE发送Attach Request消息后，在45秒内未发送Attach Complete消息，表示附着数据业务失败。
DetachAttempt 去附着尝试 UE发送Detach Request消息或基站发送Detach Request消息请求去附着到数据业务。
DetachSuc 去附着成功 "以下情况表示UE去附着数据业务成功：UE向基站发送Detach Request消息后，在15秒内收到基站发出的Detach Accept消息。
基站向UE发送Detach Request消息后，在15秒内收到UE发出的Detach Accept消息" RRCSetupReq RRC（Radio Resource Control）连接建立请求 UE发送RRC Connection Request消息请求建立RRC连接。
RRCSetupSuc RRC连接建立成功 MS发出RRC Connection Request，并且2.5s 内UE发出RRC Connection Setup Complete，则触发该事件。
RRCSetupFail RRC连接建立失败 MS发出RRC Connection Request，并且2.5s 内UE没有发出RRC Connection Setup Complete，或者收到RRC Connection Reject，则触发该事件。
ERABSetupAttempt ERAB（Evolved Radio Access Bearer）建立尝试如果RRC Connection Reconfiguration消息中包含特定的信元（“drb-ToAddModList”或“drb-ToAddModifyList”），并且不包含信元“mobilityControlInfo”，表示ERAB建立尝试。
A1-B2事件 (LTE)
LTE支持的切换事件有A类和B类，其中A类本用作系统内测量，B类被用作系统间测量A1事件：表示服务小区信号质量高于一定门限；A2事件：表示服务小区信号质量低于一定门限；A3事件：表示邻区质量高于服务小区质量，用于同频、异频的基于覆盖的切换；A4事件：表示邻区质量高于一定门限，用于基于负荷的切换，可用于负载均衡；A5事件：表示服务小区质量低于一定门限并且邻区质量高于一定门限，可用于负载均衡; 异系统测量事件：B1事件：邻小区质量高于一定门限，用于测量高优先级的异系统小区；B2事件：服务小区质量低于一定门限，并且邻小区质量高于一定门限，用于相同或较低优先级的异系统小区的测量。
LTE移动性参数(全局)1最小接入电平基本信息参数名称(中文)参数名称(英文)取值范围单位最小接收电平QrxLevMin LTE (-140 (44)3G (-119 (25)2G (-115 (25)dBm缺省值开局建议值配置步长参数类型LTE:-1403G邻区频点:-119 2G邻区频点:-115LTE:-1223G:-1192G:-1152长整型影响范围修改生效方式参数出处适用制式LTE小区2G/3G邻区频点修改立即生效3GPP TS 36.331通用参数功能该参数表示UE在该小区驻留需满足的最小接收电平门限。
该值取值范围是2G/3G接收电平的实际值，对于LTE/3G , 实际的RxlevMin 等于SIB3/SIB6的IE value的两倍，调整步长为2dbm。
对于2G，实际的RxlevMin等于SIB7的 (IE value * 2) 115，调整步长为2dBm当UE测量到的2G/3G电平满足S准则时，UE才可能驻留在该小区。
参数调整影响调整该参数的门限值，会对小区的选择和驻留有所影响。
QrxLevMin如果设置过高，则UE将无法驻留到该小区。
2高优先级重选门限基本信息参数功能当高优先级小区的S值在一定时间内高于该阀值(threshXHigh)后，UE可以重选到该小区。
ltea3事件触发条件(一)
ltea3事件触发条件(一)ltea3事件触发条件背景介绍近日，ltea3事件引起了广泛关注。
这一事件的发生，引发了人们对网络安全的再次关注。
本文将介绍ltea3事件的相关信息，以及导致该事件发生的触发条件。
事件概述ltea3事件是一起网络安全事件，涉及到大量用户的个人信息被泄露。
据相关报道，攻击者利用了一个安全漏洞，成功获取了用户的敏感信息。
这些信息包括但不限于个人身份信息、联系方式等。
触发条件一：存在安全漏洞•在ltea3事件中，攻击者能够成功获取用户信息的主要原因是应用程序存在安全漏洞。
•这个安全漏洞可以是程序代码中的一个错误，导致攻击者能够绕过系统的安全机制。
•安全漏洞可能是由于疏忽、未经充分测试或攻击者的有意破坏行为引起的。
触发条件二：缺乏安全意识•除了存在安全漏洞外，ltea3事件的发生还与用户个人的安全意识和习惯有关。
•用户可能在注册账号时使用了容易被猜测的密码，或者未定期更改密码，造成账号被攻破。
•用户还可能没有意识到点击垃圾邮件、下载未知来源的应用等行为的风险，从而打开了攻击者的入口。
触发条件三：缺乏安全措施•除了用户个人的安全意识外，应用程序和网络平台所提供的安全措施也是防止类似事件发生的重要因素。
•如果应用程序没有及时更新漏洞补丁或者没有采用先进的加密技术，攻击者就有可能利用其进行攻击。
•同样，网络平台在处理用户数据时，如果没有采取妥善的数据加密和访问控制措施，也会存在被攻破的风险。
总结ltea3事件的发生不仅仅是一个特例，它提醒我们在网络时代保护个人信息的重要性。
触发条件一般包括存在安全漏洞、缺乏安全意识和缺乏安全措施。
为了避免个人信息泄露，我们应当加强对网络安全的认识，提高个人安全意识，同时也需要加强应用程序和网络平台的安全措施。
只有共同努力，才能创造一个更加安全可靠的网络环境。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
关键点里的：
LTE主要有下面几种类型测量报告：
Event A1 (Serving becomes better than threshold)：表示服务小区信号质量高于一定门限，满足此条件的事件被上报时，eNodeB停止异频/异系统测量；类似于UMTS里面的2F事件； Event A2 (Serving becomes worse than threshold)：表示服务小区信号质量低于一定门限，满足此条件的事件被上报时，eNodeB启动异频/异系统测量；类似于UMTS里面的2D事件； Event A3 (Neighbour becomes offset better than serving)：表示同频邻区质量高于服务小区质量，满足此条件的事件被上报时，源eNodeB启动同频切换请求；不用启动定时器或者门限吗？
Event A4 (Neighbour becomes better than threshold)：表示异频邻区质量高于一定门限量，满足此条件的事件被上报时，源eNodeB启动异频切换请求；
Event A5 (Serving becomes worse than threshold1 and neighbour becomes better than threshold2)：表示服务小区质量低于一定门限并且邻区质量高于一定门限；类似于UMTS里的2B事件；
Event B1 (Inter RAT neighbour becomes better than threshold)：表示异系统邻区质量高于一定门限，满足此条件事件被上报时，源eNodeB启动异系统切换请求；类似于UMTS里的3C 事件；
Event B2 (Serving becomes worse than threshold1 and inter RAT neighbour becomes
better than threshold2)：表示服务小区质量低于一定门限并且异系统邻区质量高于一定门限，类似于UMTS里进行异系统切换的3A事件。
另一种说法：
Event A1 A1测量报告服务小区的RSRP值比绝对门限阈值高时，输出A1测量报告。
Event A2 A2测量报告服务小区的RSRP值比绝对门限阈值低时，输出A2测量报告。
Event A3 A3测量报告邻区的RSRP值比服务小区的RSRP值高时，输出A3测量报告。
Event A4 A4测量报告邻区的RSRP值比绝对门限阈值高时，输出A4测量报告。
Event A5 A5测量报告服务小区的RSRP值比绝对门限阈值1低且邻区的RSRP值比绝对门限阈值2高时，输出A5测量报告。
Event B1 B1测量报告邻区的RSRP值比绝对门限阈值高时，输出B1测量报告。
Event B2 B2测量报告服务小区的RSRP值比绝对门限阈值1低且邻区的RSRP值比绝对门限阈值2高时，输出B2测量报告。