GGD配电柜出厂检验报告(资料分享)

合集下载

配电箱出厂检验报告通用模板

产品出厂检验报告
产品编码
产品名称配电柜
产品型号规格10KW/380V
产品数量总共20台
出厂日期2021年05月21日
公司名称:
盖章：
产品编码
出厂编码
额定电流
序号
检验
项目
检验内容及方法
标准要求
实测值
一次
合格
修后
合格
1
一
般
检
查
1）外观质量
柜体内外喷漆质量
柜体正面是无反射的桔形漆，正面和侧面涂层不允许有皱纹、气泡、透底等缺陷。色泽均匀，无明显刷痕、伤痕、机械杂质，表面漆色一致。
(3)有接地装置专用的螺栓和垫圈。
——
√
4
结论：此配电柜经检验调试合格，准予出厂。
检验员：2021年05月21日
注：一次合格、修后合格记为“√”，一次不合格、修后不合格记为“×”。有“*”号为直接判产品不合格。
检验标准：GB7251.1-2005
(4)母线及二次回路导线均符合工艺求。
——
√
6）间隙和爬电距离
检查各导电回路带电部件之间及其金属结构件之间，母线与母线之间的电气间隙和爬电距离。
(1)母线与母线之间，元件进出线端子之间的电气间隙不小于8mm。
(2)母线与母线之间，元件进出线端子之间的爬电距离不小于12.5mm。
——
√
7）绝缘电阻
检查各导电回路带电部件之间及其金属结构件之间，母线与母线之间的绝缘电阻。
绝缘电阻相间.相对地均不小于5MΩ。
5 MΩ
√
序号
检验项目
检验内容及方法
标准要求
实测值
一次
合格
修后
合格

GGD检验报告

9、验收标准
按照国家GB50150-2006、BG50303-2002执行
品管部签字：
年月日
设计签字：
年月日
制造签字：
年月日
仓库接收签字：
年月日
电器柜出厂检验报告
年月日
用户名称
云南大理正大
合同编号
产品名称
配电柜
安装人员
梁朝仁于溁
设计人员
张生勃
数量
4
检验项目
检验内油污、灰尘等污垢，不得有裂纹、凹坑、划痕，保证柜体表面漆面完整、（颜色符合合同要求）。
2．一般
检查
检查导线与容量符合：
电器的布置、安装是否正确：
各元件固定牢固，无歪斜和破损现象：
金属框架接地或接零、接地标志、线是否正确明显：
机械操作元件是否有效：
3．一次
电器
元件
装配
电器保护和保护导体的截面积、柜间线路绝缘电阻值测试、柜（屏）、采用兆欧表进行对地检测、符合国家规定。
关键元器件要与认证产品安全件一览表相一致。包括断路器、刀开关、绝缘支撑件等产品的规格型号、厂家名称要符合合同技术要求。
母线搭接牢固，接触良好；相序标志正确、保护接地标志清楚；规格尺寸符合设计图纸要求。
4．二次
配线
配线合理、正确、走线整齐、固定牢靠、地线使用正确；二次元件安装牢固、接线正确。
控制线松动：
多股导线必须采用按装线鼻，通过插入式端子必须搪锡。连接导线要有合格证、型号与设计图纸相一致。
5．通电试验
通电操作，其动作应可靠、正常，符合设计要求。不应出现不动作或误动作。

低压开关柜GGD,现场测试报告(空白)

mΩ
柜门板接地点与保护导体之间
mΩ
8
介电强度试验
耐压值(2.5KV)应无击穿放电现象，测试时间为1秒钟。
手柄3.75KV 1秒钟，应无击穿和放电现象
.所有带电部件与裸露导电部件之间，施加电压2500V、施压时间5s，无击穿闪络。
每个极和连接到裸露导电部件上的所有其它极之间，施加电压2500V、施压时间5s，无击穿闪络。
mm
5
防护等级测量
IP30,直径2.5的钢丝，施加3N的力，钢丝应不能进入柜内
6
绝缘电阻
绝缘电阻(MΩ)电阻应不小于1 MΩ/V A+B+C+N-地
MΩ
7
工频过压保护
试验
将电容拆除，给装置接上电源，并将电容器开关投切开关闭合，在1.1~1.2倍的额定电压范围内，应在60秒内将电容器切除。
V秒
切除
8
保护电路的连续性检验
不由主电路直接供电的辅助电路与柜架之间，施加电压2500V、施压时间5s，无击穿闪络。
带电部件和用金属箔裹缠的绝缘操作手柄之间，施加电压3750V、施压时间5s，无击穿闪络。
总结论：
经
检验负责人：日期：客户签名：日期：
备注：
————————有限公司
低压成套开关设备产品安装现场测试报告
（依据标准GB7251.1-2005）第页共页
3
机械操作
对安装在装置内的开关电器及所有手动部件，机械操作5次，其机构动作应可靠、正常，连锁机构应符合要求
4
电气间隙、
爬电距离的测量
电气间隙≥8 mm
mm
爬电距离≥12.5 mm
mm
5
防护等级测量
IP30,直径2.5的钢丝，施加3N的力，钢丝应不能进入柜内

交流低压开关柜GGD例行检验报告

XXX电气有限公司
交流低压开关柜GGD例行检验报告
No：
产品名称：交流低压开关柜
型号规格：GGD-1000
依据标准：GB/T 7251.12-2013
出厂编号：2020101021
地下室低压配电柜
生产日期：2020年10月10日
序
项目
技术要求
实测
试验结果
1
一般检查
柜体各功能单元门的开启角应大于90°，转动灵活
符合
对主电路和不与主电路直接连接的辅助电路之间、辅助电路与框架之间应能受50Hz，1890V历时7s耐压试验。
符合
9
保护措施和保护电路的连续性
有主接地点和接地标记，零部件和电器元件的保护接地使用专用的螺钉，以保证保护电路的连续性。
符合
电阻值应在100mΩ以下。
主开关安装支架-主接地
≤50MΩ
分支开关安装支架-主接地
≤50MΩ
接线端子支架-主接地
≤50MΩ
门锁-主接地
≤50MΩ
10
操作试验
手动操作试验：装置中所有手动操作部分：如主开关的操作手柄等手动操作5次而无异常现象出现。有连锁功能要求的应连锁可靠。
符合
11
一致性检查
1关键元器件和材料、2.结构 3.铭牌应与型式试验报告描述一致
符合
12
检验结论：该产品经我公司检验合格，准予出厂
符合
5
内部电路和连接
装应符合认证产品的一致性要求、工艺要求和图纸规定的要求。
符合
6
外接端子
数量、类型和标识应符合成套设备输出接线的要求及型式试验报告的要求
符合
7
绝缘电阻
相与相之间,相与地之间的绝缘电阻值绝缘电阻不应小于1000Ω/V，规定≥10MΩ。

GGD盘出厂检验报告

GGD 低压配电盘出厂检验报告
用户：产品名称规格：出厂编号：
1、外观检查：检查壳体外壁、漆膜、元器件安装及参数，电气间隙和爬电距
离、母线和布线、各部件紧固程度，防护及接地等。

应符合技术条件和图纸要求。

检查结果：
2、摇绝缘、打耐压
2.1、主进柜、联络柜及分路柜试验
2.2 无功功率补偿装置试验
3、拉合闸操作及通电检验
3.1、所有开关操作应转动灵活、可靠，位置指示正确固定牢固，电气接触良好；
3.2、电压指示仪表转动灵活无卡阻，指示正确； 3.3、信号灯指示符合技术条件和图纸要求； 3.4、照明回路符合图纸要求。

检验结果：
4、检验结论：检验员：
年月日
绝缘缘YUA 缘电阻
A 、
B 、
C 短路后对地测试结果结论
绝缘电阻
MΩ
交流耐压
主回路各相对地2.5KV1分钟，无击穿、无飞弧
辅助电路对地2.5KV1分钟，无击穿、无飞弧带电部件对手柄3.75KV1分钟，无击穿、无飞弧
项目
相别
A 对地
B 对地
C 对地相之间测试结果结论
绝缘电阻
MΩ
MΩ
MΩ
MΩ
交流耐压主回路各相对地2.5KV1分钟，无击穿、无飞弧
辅助电路对地2.5KV1分钟，无击穿、无飞弧
带电部件对手柄3.75KV1分钟，无击穿、无飞弧。

低压配电柜产品出厂检验报告

低压配电柜产品出厂检验报告一、检验概述本报告是对低压配电柜产品进行出厂检验的结论性报告，旨在验证产品的性能和质量是否符合相关标准和客户要求。

本次出厂检验采用了标准化的测试方法和设备，确保结果的准确性和可靠性。

二、检验项目1.外观检验：对产品的外观进行全面检查，包括外壳是否完整、标识是否清晰、面板是否平整等。

2.功能检验：对产品的各项功能进行测试，包括开关操作是否正常、电流是否在规定范围内、短路和过载保护是否可靠等。

3.绝缘电阻检验：对产品的绝缘电阻进行测量，确保产品的绝缘性能符合要求。

4.效应应力测试：对产品进行效应应力测试，模拟产品在正常使用过程中的负荷情况，确保产品的结构和材料能够承受正常工作状态下的应力。

5.耐压试验：对产品进行耐压试验，模拟产品在特殊环境下的工作情况，例如高温、低温和高湿度等，确保产品能够在各种环境下正常工作。

6.电气参数测量：对产品的电气参数进行测量，例如电压、电流、功率因数等，确保产品符合设计要求。

7.电弧灭弧性能测定：对产品的电弧灭弧性能进行测试，确保产品在发生电弧事故时能够迅速灭弧，以保护人员和设备的安全。

三、检验结果经过上述项目的检验，本次低压配电柜产品出厂检验的结果如下：1.外观检验：产品的外观完整，标识清晰，面板平整。

2.功能检验：产品的开关操作正常，电流在规定范围内，短路和过载保护可靠。

3.绝缘电阻检验：产品的绝缘电阻符合要求。

4.效应应力测试：产品在效应应力测试中表现良好，未出现结构破损或材料变形等情况。

5.耐压试验：产品在耐压试验中正常工作，无异常情况发生。

6.电气参数测量：产品的电气参数符合设计要求。

7.电弧灭弧性能测定：产品的电弧灭弧性能达到或超过标准规定，对电弧能够迅速灭弧。

综上所述，本次低压配电柜产品出厂检验的结果符合相关标准和客户要求，产品在各项指标上均符合设计要求，质量可靠、性能稳定。

四、结论1.本次低压配电柜产品出厂检验的结果显示，产品在外观、功能、绝缘性能、结构强度、耐压能力、电气参数和电弧灭弧性能等方面都符合要求。

配电柜出厂检验报告

合格/不合格
包
装
1、编号管、图纸、安装附件应齐全。
合格/不合格
2、柜面、显示部分或突出部分应有保护措施。
合格/不合格
3、包装应有方向说明及注意事项。
合格/不合格
质检综合结论：
检验部门：
ห้องสมุดไป่ตู้质检人：
检验日期：
合格/不合格
2、主接地线与柜体裸露导电部件之间，接地电阻<Ω，试验电流为》10A。
合格/不合格
通电
测试
1、按装置的电气原理图要求进行模拟动作试验，试验结果应符合要求，5次以上均正常动作。
合格/不合格
2、安装置的电气原理图要求进行故障模拟试验，其故障信号和报警指示应正确。
合格/不合格
3、通电试验时每个回路的一、二次接线均正确无误。
合格/不合格
4、各回路开关的容量应与图纸相符。
合格/不合格
显示
指示
1、各种标签标识必须与图纸、工艺测试指示相吻合。
合格/不合格
2、同一设备不同标示、指示应协调一致。
合格/不合格
性能
参数
1、变频器、软启动器、热继电器、时间继电、仪表等参数必须按所需功能设定。
合格/不合格
品牌检验
1、元件器品牌型号应与图纸或者报价单一致。
合格/不合格
耐压
测试
1、主电路带电部件与地（框架）之间，2500V在5秒无击穿、无闪络现象。
合格/不合格
2、主电路母排各相之间，2500V5秒无击穿、无闪络。主回路导线之间，750V5秒无击穿、无闪络，二次回路500V5秒无击穿、无闪络。
合格/不合格
保护电路的连续性
1、主接地线与门（箱体）之间的的连续性试验，接地电阻&现方式做保护处理对用户上传分享的文档内容本身不做任何修改或编辑并不能对任何下载内容负责

GGD配电柜出厂检验报告

GGD型交流低压配电控制柜出厂检验报告型号：___________________一、目的通过检查和试验，对GGD型交流低压配电柜在技术条件，范围的性能、安全性、适应性及制造、安装工艺进行验证，使产品达到出厂要求。

二、主要依据1、LEC439-1-1992低压成套开关设备第一部分2、GB7251-1-1997低压成套开关设备和控制条一部分三、试验项目1、柜体检验2、装配检验3、断路器检验4、隔离刀开关检验5、主四路无载通电操作试验6、绝缘电阻测试7、介电强度试验8、结论GGD型交流低压配电柜出厂检验报告第2页（英文版）Two regulations promulgated for implementation is in the party in power for a long time and the rule of law conditions, the implementation of comprehensive strictly strategic plan, implementation in accordance with the rules and discipline to manage the party, strengthen inner-party supervision of major initiatives. The two regulations supporting each other, the < code > adhere to a positive advocate, focusing on morality is of Party members and Party leading cadres can see, enough to get a high standard; < rule > around the party discipline, disciplinary ruler requirements, listed as "negative list, focusing on vertical gauge, draw the party organizations and Party members do not touch the" bottom line ". Here, the main from four square face two party rules of interpretation: the first part introduces two party Revised regulations the necessity and the revision process; the second part is the interpretation of the two fundamental principles of the revision of laws and regulations in the party; the third part introduces two party regulations modified the main changes and needs to grasp several key problems; the fourth part on how to grasp the implementation of the two regulations of the party. < code > and < Regulations > revised the necessity and revisedhistory of the CPC Central Committee the amendment to the Chinese Communist Party members and leading cadres honest politics several guidelines > and < Chinese Communist Party discipline and Punishment Regulations > column 1 by 2015 to strengthen party laws and regulations focus. Two party regulations revision work lasted a Years, pooling the wisdom of the whole party, ideological consensus, draw historical experience, respect for the wisdom of our predecessors, which reflects the unity of inheritance and innovation; follow the correct direction, grasp the limited goals, adhere to the party's leadership, to solve the masses of the people reflect a focus on the problem. The new revision of the < code > and < rule >, reflects the party's 18 and the eighth session of the third, the spirit of the fourth plenary session, reflecting the experience of studying and implementing the General Secretary Xi Jinping series of important speech, reflects the party's eighteen years comprehensive strictly practice. (a) revised two regulations of the party need of < the ICAC guidelines > in < in 1997 Leaders as members of the Communist Party of China clean politics certain criteria (Trial) > based on revised, the promulgation and implementation of January 2010, to strengthen the construction of the contingent of leading cadres play animportant role. But with the party to manage the party strictly administering the deepening, has not been able to fully meet the actual needs. Content is too complicated, "eight prohibition, 52 are not allowed to" hard to remember, and also difficult to put into practice; the second is concisely positive advocated by the lack of prohibited provisions excessive, no autonomy requirements; the third is banned terms and discipline law, both with the party discipline, disciplinary regulations repeat and Criminal law and other laws and regulations repeat; the fourth is to "clean" the theme is not prominent, not for the existing problems, and is narrow, only needle of county-level leading cadres above. < rule > is in 1997 < Chinese Communist Party disciplinary cases (Trial) > based on revision, in December 2003 the promulgation and implementation, to strengthen the construction of the party play very important role. Along with the development of the situation, which many provisions have been unable to fully meet the comprehensive strictly administering the practice needs. One is Ji law, more than half of the provisions and criminal law and other countries laws and regulations Repetition; two is the political discipline regulations is not prominent, not specific, for violation of the party constitution, damage theauthority of Party Constitution of misconduct lack necessary and serious responsibility to pursue; third is the main discipline for the leading cadres, does not cover all Party members. Based on the above situation, need to < the criterion of a clean and honest administration > and < rule > the two is likely to be more relevant regulations first amendment. By revising, really put the authority of Party discipline, the seriousness in the party tree and call up the majority of Party members and cadres of the party constitution of party compasses party consciousness. (II) two party regulations revision process the Central Committee of the Communist Party of China attaches great importance to two regulations revision . Xi Jinping, general books recorded in the Fifth Plenary Session of the eighth session of the Central Commission for Discipline Inspection, on the revised regulations < > made clear instructions. According to the central deployment, the Central Commission for Discipline Inspection from 2014 under six months begin study two regulations revision. The Standing Committee of the Central Commission for Discipline Inspection 4 review revised. Comrade Wang Qishan 14 times held a special meeting to study two regulations revision, amendment clarifies the direction, major issues of principle, path and target,respectively held a forum will listen to part of the province (area) secretary of the Party committee, Secretary of the Discipline Inspection Commission, part of the central ministries and state organs DepartmentThe first party committee is mainly responsible for people, views of experts and scholars and grassroots party organizations and Party members. Approved by the Central Committee of the Communist Party of China, on 7 September 2015, the general office of the Central Committee of the Party issued a notice to solicit the provinces (autonomous regions, municipalities) Party, the central ministries and commissions, state ministries and commissions of the Party (party), the General Political Department of the military, every 3 people organization of Party of two regulations revision opinion. Central Commission for Discipline Inspection of extensive solicitation of opinions, careful study, attracting, formed a revised sent reviewers. In October 8 and October 12, Central Committee Political Bureau Standing Committee and the Political Bureau of the Central Committee After consideration of the two regulations revised draft. On October 18, the Central Committee of the Communist Party of China formally issued two regulations. Can say, two laws amendment concentrated thewisdom of the whole party, embodies the party. Second, < code > and < Regulations > revision of the basic principles of two party regulations revision work and implement the party's eighteen, ten eight plenary, the spirit of the Fourth Plenary Session of the Eleventh Central Committee and General Secretary Xi Jinping important instructions on the revised < low political criterion > and < Regulations >, highlighting the ruling party characteristics, serious discipline, the discipline quite in front of the law, based on the current, a long-term, advance as a whole, with Bu Xiuding independent < rule > and < rule >. Main principle is: first, adhere to the party constitution to follow. The constitution about discipline and self-discipline required specific, awaken the party constitution of party compasses party consciousness, maintaining the authority of the constitution. General Secretary Xi Jinping pointed out that "no rules, no side round. Party constitution is the fundamental law, the party must follow the general rules. In early 2015 held the eighth session of the Central Commission for Discipline Inspection Fifth Plenary Session of the 16th Central Committee, Xi Jinping again pointed out that constitution is the party must follow the general rules, but also the general rules." the revision of the< code > and < rule > is Method in adhere to the regulations established for the purpose of combining rule of virtue is to adhere to the party constitution as a fundamental to follow, the constitution authority set up, wake up the party constitution and party rules the sense of discipline, the party constitution about discipline and self-discipline specific requirements. 4 second is to adhere to in accordance with the regulations governing the party and the party. The Party of rule of virtue "de", mainly refers to the party's ideals and beliefs, excellent traditional style. The revised the < code > closely linked to the "self-discipline", insisting on the positive initiative, for all members, highlight the "vital few", emphasized self-discipline, focusing on the morality, and the majority of Party members and the ideological and moral standards. The revised < > Ji method separately, Ji, Ji Yan to Method, as a "negative list", emphasizing the heteronomy, focusing on vertical gauge. Is this one high and one low, a positive reaction, the strict party discipline and practice results transformation for the integration of the whole party to observe moral and discipline requirements, for the majority of Party members and cadres provides benchmarking and ruler. Third, insist on to. In view of the problems existing in theparty at the present stage, the main problems of Party members and cadres in the aspect of self-discipline and abide by the discipline to make clearly defined, especially the party's eighteen years strict political discipline and political rules, organization and discipline and to implement the central eight provisions of the spirit against the four winds and other requirements into Disciplinary provisions. Not one pace reachs the designated position, focusing on in line with reality, pragmatic and effective. After the revision of major changes, major changes in the < code > and < rule > modified and needs to grasp several key problems (a) < code > < code > adhere to according to regulations governing the party and party with morals in combination, for at the present stage, the leadership of the party members and cadres and Party members in existing main problems of self-discipline, put forward principles, requirements and specifications, showing Communists noble moral pursuit, reflected at all times and in all over the world ethics from high from low 5 common requirements. One is closely linked to the "self-discipline", removal and no direct relation to the provisions of . the second is adhere to a positive advocate, "eight prohibition" 52 are not allowed to "about the content of the" negative list moved into synchronizationamendment < cases >. Three is for all the party members, will apply object from the leadership of the party members and cadres to expand to all Party members, fully embodies the comprehensive strictly required. The fourth is prominent key minority, seize the leadership of the party members and cadres is the key, and put forward higher requirements than the ordinary Party members. Five is to simplify, and strive to achieve concise, easy to understand, easy to remember. The revised < code > is the ruling Party since the first insists on a positive advocate forAll Party members and the self-discipline norms, moral declaration issued to all members of the party and the National People's solemn commitment. > < criterion of a clean and honest administration consists of 4 parts, 18, more than 3600 words. After the revision of the < code >, a total of eight, 281 words, including lead, specification and Party member cadre clean fingered self-discipline norms, etc. Part 3 members low-cost clean and self-discipline, the main contents can be summarized as "four must" "eight code". Lead part, reiterated on ideal and faith, fundamental purpose, the fine traditions and work style, noble sentiments, such as "four must" the principle of requirements, strong tone of self-discipline, The higher request for 6 andsupervised tenet, the foothold in permanent Bao the party's advanced nature and purity, to reflect the revised standards requirements. Members of self-discipline norms around the party members how to correctly treat and deal with the "public and private", "cheap and rot" thrifty and extravagance "bitter music", put forward the "four norms". Party leader cadre clean fingered self-discipline norms for the leadership of the party members and cadres of the "vital few", around the "clean politics", from civil servant of the color, the exercise of power, moral integrity, a good family tradition and other aspects of the leadership of the party members and cadres of the "four norms" < > < norm norm. "The Party member's self-discipline norms" and "party members and leading cadre clean fingered self-discipline norms," a total of eight, collectively referred to as the "eight". "Four must" and "eight" of the content from the party constitution and Party's several generation of leaders, especially Xi Jinping, general secretary of the important discussion, refer to the "three discipline and eight points for attention" statements, and reference some embody the Chinese nation excellent traditional culture essence of epigrams. (2) the revised regulations, the main changes in the revised Regulations > to fully adapt to thestrictly requirements, reflects the according to the regulations governing the law of recognition of deepening, the realization of the discipline construction and Jin Ju. < rule > is party a ruler, members of the basic line and follow. And the majority of Party members and cadres of Party organizations at all levels should adhere to the bottom line of thinking, fear discipline, hold the bottom line, as a preventive measure, to keep the party's advanced nature and purity. 1, respect for the constitution, refinement and discipline. Revised < rule > from comprehensive comb physical constitution began, the party constitution and other regulations of the Party of Party organizations and Party discipline requirements refinement, clearly defined in violation of the party constitution will be in accordance with regulations to give the corresponding disciplinary action. The original 10 categories of misconduct, integration specification for political discipline, discipline, honesty and discipline masses Ji Law and discipline and discipline and other six categories, the content of < rule > real return to Party discipline, for the majority of Party members and listed a "negative list. 7 2, highlighting the political discipline and political rules. > < Regulations according to the stage of the discipline of outstandingperformance, emphasizing political discipline and political rules, organization and discipline, in opposition to the party's leadership and the party's basic theory, basic line, basic program and basic experience, the basic requirement of behavior made prescribed punishment, increase the cliques, against the organization such as violation of the provisions, to ensure that the central government decrees and the Party of centralized and unified. 3, adhere to strict discipline in the law and discipline In front, Ji separated. Revised < Regulations > adhere to the problem oriented, do Ji separated. Any national law existing content, will not repeat the provisions, the total removal of 79 and criminal law, repeat the content of the public security management punishment law, and other laws and regulations. In the general reiterated that party organizations and Party members must conscientiously accept the party's discipline, die van comply with national laws and regulations; at the same time, to investigate violations of Party members and even criminal behavior of Party discipline and responsibility, > < Regulations distinguish five different conditions, with special provisions were made provisions, so as to realize the connection of Party discipline and state law. 4, reflect Wind building and anti-corruptionstruggle of the latest achievements. < rule > the party's eighteen years implement the spirit of the central provisions of the eight, against the requirements of the "four winds" and transformation for disciplinary provisions, reflecting the style construction is always on the road, not a gust of wind. In the fight against corruption out of new problems, increase the trading rights, the use of authority relatives profit and other disciplinary terms. Prominent discipline of the masses, the new against the interests of the masses and ignore the demands of the masses and other disciplinary terms and make provisions of the disposition and the destruction of the party's close ties with the masses.Discipline to protect the party's purpose. 8 of these regulations, a total of three series, Chapter 15, 178, more than 24000 words, after the revision of the regulations a total of 3 series, Chapter 11, 133, 17000 words, divided into "general" and "special provisions" and "Supplementary Provisions" Part 3. Among them, add, delete, modify the provisions of the proportion of up to nearly 90%. 1, the general general is divided into five chapters. The first chapter to the regulations of the guiding ideology, principles and scope of application of the provisions, highlight the strengthening ofthe party constitution consciousness, maintenance the authority of Party Constitution, increase the party organizations and Party members must abide by the party constitution, Yan Centralized centralized, would examine at all levels of the amended provisions implementing and maintaining Party discipline, and consciously accept the party discipline, exemplary compliance with national laws and regulations. The second chapter of discipline concept, disciplinary action types and effects of the regulations, will be a serious warning from the original a year for a year and a half; increase the Party Congress representative, by leaving the party above (including leave probation) punishment, the party organization should be terminated its representative qualification provisions. The third chapter of the disciplinary rules of use prescribed in the discipline rectifying process, non convergence, not close hand classified as severely or heavier punishment. "Discipline straighten "At least eighteen years of five years, these five years is to pay close attention to the provisions of the central eight implementation and anti -" four winds ". The fourth chapter on suspicion of illegal party disciplinary distinguish five different conditions, with special provisions were madeprovisions, to achieve effective convergence of Party and country 9 method. < rule > the provisions of Article 27, Party organizations in the disciplinary review found that party members have committed embezzlement, bribery, dereliction of duty dereliction of duty and other criminal law act is suspected of committing a crime shall give cancel party posts, probation or expelled from the party. The second is < Regulations > Article 28 the provisions of Party organizations in the disciplinary review But found that party members are stipulated in the criminal law, although not involved in a crime shall be investigated for Party discipline and responsibility should be depending on the specific circumstances shall be given a warning until expelled punishment. This situation and a difference is that the former regulation behavior has been suspected of a crime, the feeling is quite strict, and the latter for the behavior not involving crime, only the objective performance of the provisions of the criminal code of behavior, but the plot is a crime to slightly. < Regulations > the 29 provisions, Party organizations in the discipline review found that party members and other illegal behavior, affect the party's image, the damage to the party, the state and the people's interests, we should depend on the situationSeriousness given disciplinary action. The loss of Party members, seriously damaging the party's image of behavior, should be given expelled from the party. At this article is party member is in violation of the criminal law outside the other illegal acts, such as violates the public security administration punishment law, customs law, financial laws and regulations behavior. The fourth is < cases > Article 32 stipulates, minor party members and the circumstances of the crime, the people's Procuratorate shall make a decision not to initiate a prosecution, or the people's court shall make a conviction and exempted from criminal punishment shall be given within the party is removed from his post, probation or expelled from the party. Party members and crime, sheets were fined in accordance with For acts; the principal Ordinance amended the provisions of the preceding paragraph. This is the new content, in order to achieve Ji method effective convergence. Five is < > the thirty third article 10 of the provisions, the Party member due to an intentional crime is sentenced to criminal law (including probation) sheets or additional deprivation of political rights; due to negligence crime and was sentenced to three years or more (excluding three years) a penalty, shall give expelled punishment. Due to negligence crime is convictedand sentenced to three years (including three years) in prison or be sentenced to public surveillance, detention, shall in general be expelled from the party. For the individual may not be expelled from the party, should control Approval. This is followed and retained the original > < Regulations the provisions of punishment party authorization rules and report to a level party organizations. For is "party members with criminal acts, and by the criminal punishment, generally should be expelled from the party". The fifth chapter of probationary Party member of the discipline and discipline after missing members of the treatment and punishment decisions, such as the implementation of the provisions, clear the related party discipline and punishment decision made after, for duties, wages and other relevant alteration formalities for the longest time. 2, sub sub section will the original regulations of10 categories of acts of violation of discipline integration revised into 6 categories, respectively, in violation of the punishments for acts of political discipline "in violation of discipline behavior of punishment" in violation of integrity of disciplinary action points "of violation punishments for acts of mass discipline" "the violation of work discipline, punishment" in violation of discipline of life behaviorpunishment "6 chapters. 3, annex" Supplementary Provisions "clear authority making supplementary provisions of, cases of interpretative organ, as well as regulations implementation time and retroactivity etc.. 11 (3) learning understanding > < regulations needs to grasp several key problems The first problem -- about the violation of political discipline behavior > < new ordinance chapter 6 the political discipline column for the six disciplines, that is the main opposition to Party leadership and the opposition of the basic theory, basic line, basic program and basic experience, basic requirements of misconduct made provisions of the disposition, especially the eighteen since the CPC Central Committee put forward the Yan Mingzheng treatment of discipline and political rules requirements and practical achievements transformation for Discipline article, increase the false debate central policies, cliques, against the organization review, make no discipline of the principle of harmony terms. These are the party's eighteen years in comprehensive strictly Process combined with the practice of rich content. (1) false debate the central policies and undermine the Party of centralized and unified the problem is made in accordance with the provisions of the party constitution. Constitution in general programme requirementsadhere to democratic centralism is one of the requirements of the construction of the party must adhere to the four cardinal. Application of this principle is not only the party the basic organization principle and is also the mass line in party life, it requires that we must fully develop inner-party democracy, respect for the dominant position of Party members, safeguarding the Party member democratic rights, give full play to the enthusiasm and creativity of the party organizations at all levels and Party members, at the same time, also must implement the right concentration, ensure the party's mission < the chaos in unity and concerted action to ensure that the party's decision to get quickly and effectively implementing. The Party Central Committee formulated the major principles and policies, through different channels and ways, fully listen to the party organizations and Party members of the opinions and suggestions, but 12 is some people face to face not to say back blather "" will not say, after the meeting said, "" Taiwan does not say, and nonsense ", in fact, not only disrupt the people thought, some causing serious consequences, the damage to the Party of the centralized and unified, hinder the central policy implementation, but also a serious violation of the democratic system of principles. There is no doubt that shall, inaccordance with the Regulations > 4 Specified in Article 6 to give the appropriate punishment. For did not cause serious consequences, to give criticism and education or the corresponding tissue processing. (2) about the destruction of the party's unity < New Regulations > the forty eighth to fifty second article, to damage Party's unity unified and violation of political discipline, punishment situation made explicit provisions. Article 52 of the new "in the party get round group, gangs seek private gain, cliques, cultivate private forces or through the exchange of interests, for their own to create momentum and other activities to gain political capital, given a serious warning or withdraw from their party posts disposition; if the circumstances are serious, to give Leave a party to observation or expelled from the party. (3) on against the organization review of the provisions of the constitution, party loyalty honesty is party members must comply with the obligations. Members must obey the organization decision, shall not violate the organization decided encounters by asking questions to find organization, rely on the organization, shall not deceive the organization, against the organization. For example, after the investigation does not take the initiative to explain the situation, but to engage inoffensive and defensive alliance, hiding the stolen money is against survey organization, is a violation of the behavior of political discipline. Article 24 of the original > < Regulations, although the provisions of the interference, hinder group review the behavior of the fabric can be severely or 13 Aggravated punishment, but did not put this kind of behavior alone as a discipline for qualitative amount of discipline. > < new regulations increase the Article 57, "anti organization review, one of the following acts, given a warning or serious warning; if the circumstances are relatively serious, giving removed from or placed on probation within the party post; if the circumstances are serious, give expelled from the party: (a) on supply or forged, destroyed, transfer, conceal evidence; (II) to prevent others expose, providing evidence Material; (III) harboring co personnel; (4) to the organization to provide false information, to hide the fact;(5) the him against the acts of the organization review. "< rule > add this clause to the Constitution requires more specific, the previous no punishment in accordance with the definite list and put forward clear punishment in accordance with. (4) about organizing or participating in superstitious activities as < Regulations > about engage in activities of。

配电柜出厂检验报告

2、安装置的电气原理图要求进行故障模拟试验，其故障信号和报警指示应正确。
合格/不合格
3、通电试验时每个回路的一、二次接线均正确无误。
合格/不合格
4、各回路开关的容量应与图纸相符。
合格/不合格
显示
指示
1、各种标签标识必须与图纸、工艺测试指示相吻合。
合格/不合格
2、同一设备不同标示、指示应协调一致。
合格/不合格
电控柜验收报告
项目名称：编号：
柜体名称
柜体规格
柜体类型
柜体数量
项目
检验项目及技术要求
检验结果
备注
绝缘
测试
1、相间电阻、及相线与中线电阻应大于500MΩ。
合格/不合格
பைடு நூலகம்耐压
测试
1、主电路带电部件与地（框架）之间，2500V在5秒无击穿、无闪络现象。
合格/不合格
2、主电路母排各相之间，2500V5秒无击穿、无闪络。主回路导线之间，750V5秒无击穿、无闪络，二次回路500V5秒无击穿、无闪络。
质检综合结论：
检验部门：
质检人：
检验日期：
合格/不合格
保护电路的连续性
1、主接地线与门（箱体）之间的的连续性试验，接地电阻<Ω，试验电流为》10A
合格/不合格
2、主接地线与柜体裸露导电部件之间，接地电阻<Ω，试验电流为》10A。
合格/不合格
通电
测试
1、按装置的电气原理图要求进行模拟动作试验，试验结果应符合要求，5次以上均正常动作。
合格/不合格
性能
参数
1、变频器、软启动器、热继电器、时间继电、仪表等参数必须按所需功能设定。
合格/不合格

低压配电柜检验报告单

手动通电调试
合格
合格
电气操作试验
合格
合格
合格
4
保护电路连续性试验
主接地点与保护电气外壳接地点电阻值＜10mΩ
双臂电桥
合格
5
功能单元互换性试验
抽出插入，分合闸，联锁试操作各5次，相同单元互换试验满足以上要求
人力操作
合格
目测
合格
2
介电强度
带电部件与地之间
60V＜Ui≤300V 2kv
30V＜Ui≤600V
30V＜Ui≤600V
2.5kv/1min无闪络或击穿
低压耐压机
合格
主电路各相之间
合格
辅助电路与地之间
合格
绝艳手柄与地之间
3.75kv/1min无闪络或击穿
合格
3
机械和电气操作试验
机械操作试验
通过设计规定的电压按原理图模拟动作试验，手动、电动操作各5次无异常现象出现。
母线
外观ቤተ መጻሕፍቲ ባይዱ
相序正确，相位标识齐全正确，表面平整，防止电措施良好。
合格
搭接处
铜排接触面平整光滑，无毛刺
塞尺
合格
装配
外观
元件符合图纸要求，紧固件无松动，铭牌正确，接地标记齐全。
目测
合格
主回路间隙（mm）
电气间隙≥10
卷尺
合格
爬电距离≥12
二次配线
连接牢固，端头有标志，敷设应层次分明，牢固。横平竖直，颜色符合设计要求。
低压配电柜检验报告单
低压配电柜实验报告单
项目名称: 永城市2015年小型农田重点县项目第三标段（电力工程）产品型号:GGD 编号：27#
检验项目
技术要求

GGD型交流低压配电柜出厂试验报告

编号：GGD 型交流低压配电柜出厂试验报告型号：××××××开关厂2023 年4 月15 日GGD 型沟通低压配电柜出厂试验报告一、目的共7 页第1 页××××××开关厂通过检查和试验，对GGD 型沟通低压配电柜在技术条件范围内的性能、安全性、适应性及制造、安装工艺进展验证，使产品到达出厂要求。

二、主要依据1、IEC439-1-1992 低压成套开关设备和掌握设备第一局部2、GB7251-1-1997 低压成套开关设备和掌握设备第一局部三、试验工程1、柜体检验。

2、装配检验。

3、断路器检验。

4、隔离刀开关检验。

5、主回路无载通电操作试验。

6、绝缘电阻测试。

7、介电强度试验。

8、结论。

附：试验报告编制说明。

出厂试验报告一、柜体检验第 2 页序检验项目号 1KS 型根底框架2应用框架相对应于每个主电路方案的变更的应 3 用框架变更和重组其敏捷性、通用性和牢靠性技术要求承受带 20mm 模数孔的 8MF 型材在根底框架根底上，配用各种经喷塑处理过的安装梁或各类处理过的通用构造另部件变更和重组各类带 20mm 模数孔的安装梁，并配以相应的通用构造件，应能敏捷自如，并且柜体的精度制量保持不变主要接触部位用 M8 滚花螺钉，次要接引用标准结果NLS 设计要求NLS 设计要求NLS 设计要求整个柜体的接地保触部位可用 M8 标准镀锌螺钉，装有电 4护完整性和牢靠性器元件的仪表门用多股软铜线与构架作牢靠连接框内上、下部均开有散热孔或栅网，其 5框内散热措施外壳防护等级不低于 IP30NLS 设计要求空气对流原理及电力设备安全运行措施仪表门、前开门、后 6 开门7静电喷塑关合门数次，应无卡阻和磨擦均匀、美观、无脱落、刮伤、缺陷等 GB7251、IEC439GB7251、IEC439 框架、安装梁、另部用镀锌螺栓作紧固连接，应牢靠、结实、 8 件之间的紧固连接无松动各类 KS 型 8MF 型 NLS 设计要求9 钢的通用尺寸符合相关的技术要求 GB/T3047、1---82各类 KS 型 8MF 型外表无裂纹、毛刺、无破坏性压痕及严 10 GB/T3047、1---82钢外观重锈蚀装拆应敏捷、便利以满足用户进、出线顶盖、板及底部板的 11 的特别要求，且底板上应有数个φ 80 可拆性NLS 设计要求二、装配检验序的敲落孔结检验工程技术要求引用标准号果1 电器元件安装合理、标准、元件有足够的爬电距离，电器距离符合要求，元件有合格证，使 GB7251、IEC439 用说明书，检验报告，质量牢靠，有保 Q/OCK11-2023 证续、装配检验序检验项目号技术要求引用标准结果母排外表应无明显锤痕、刮伤、母线搭2母线外观及接触性接面应平坦，用0。

配电柜出厂检验报告新编

电控柜验收报告
项目名称：编号：
柜体名称
柜体规格
柜体类型
柜体数量
项目
检验项目及技术要求
检验结果
备注
绝缘
测试
1、相间电阻、及相线与中线电阻应大于500MΩ。
合格/不合格
耐压
测试
1、主电路带电部件与地（框架）之间，2500V在5秒无击穿、无闪络现象。
合格/不合格
2、主电路母排各相之间，2500V5秒无击穿、无闪络。主回路导线之间，750V5秒无击穿、无闪络，二次回路500V源自秒无击穿、无闪络。合格/不合格
保护电路的连续性
1、主接地线与门（箱体）之间的的连续性试验，接地电阻<0.1Ω，试验电流为》10A
合格/不合格
2、主接地线与柜体裸露导电部件之间，接地电阻<0.1Ω，试验电流为》10A。
合格/不合格
通电
测试
1、按装置的电气原理图要求进行模拟动作试验，试验结果应符合要求，5次以上均正常动作。
合格/不合格
2、安装置的电气原理图要求进行故障模拟试验，其故障信号和报警指示应正确。
合格/不合格
3、通电试验时每个回路的一、二次接线均正确无误。
合格/不合格
4、各回路开关的容量应与图纸相符。
合格/不合格
显示
指示
1、各种标签标识必须与图纸、工艺测试指示相吻合。
合格/不合格
2、同一设备不同标示、指示应协调一致。
合格/不合格
质检综合结论：
检验部门：
质检人：
检验日期：
合格/不合格
性能
参数
1、变频器、软启动器、热继电器、时间继电、仪表等参数必须按所需功能设定。
合格/不合格

GGD出厂检验报告

检查布线，并进行电气功能试验，功能正常
结论
结论：本产品依据GB7251.12-2013和产品技术条件检验。□合格□不合格
检查结果：合格√，不合格×，返工合格△
检验员日期
2，每一相和裸露导电部件上的所有其他相之间）（1890V.1s）
3，带电部件和用金属薄裹缠的绝缘手柄之间（2835V.1s）
4，不由主电路直接供电的辅助电路与框架之间（1890V.1s）
绝缘电阻
每条电路与外露可导电部件之间的绝缘电阻至少为1000Ω/V
9
布线、操作性能和功能
铭牌应坚固、耐久。位置明显，内容符合标准和型式试验报告的要求；器件和元件标识正确
爬电距离
两导电部件沿绝缘表面之间的最短距离≥12.5mm
3
电击防护和保护电路的完整性
基本防护：靠外壳防护，电气间隙和爬电距离满足要求，且只能用要药匙或者工具才能打开.
故障防护：是否有保护导体且截面积最小为10mm²，成套设备的所有外露可导电部分均连接在一起，并连接至保护导体上，或通过接地导体与接地装置连接.
螺钉和螺栓的连接是否有正确的松紧度。
试验电流设定为25A，接地电阻值为0.1Ω以下。
仪表门锁为主接地点
前门锁为主接地点
后上门锁为主接地点
后下门锁为主接地点
刀开关手柄为主接地点
断路器框架为主接地点
4
开关器件和原件的组合
内装元件的安装和标识应符合图纸规定和规范表要求，特殊元件要有说明书
接线、相序色标正确；接地紧密，无覆盖物、无生锈。接地符号明显
5
内部电路和连接
螺钉和螺栓的连接在任意的基座上是否有正确的松紧度检查导体是否ຫໍສະໝຸດ 合标准和型式试验报告的要求6
外接电线端子

电控柜出厂检验报告

电控柜出厂检验报告一、检验目的电控柜是工业生产过程中的重要设备之一，其质量和性能直接关系到生产线的稳定运行和安全生产。

本次出厂检验的目的是确保电控柜在设计和制造过程中的合格性，以及保证其在实际使用过程中的性能和安全性。

二、检验内容1.外观检验：检查电控柜表面涂装是否均匀、无划痕及锈蚀，标志标牌是否齐全、清晰可辨，连接线路是否整齐，无错位等情况。

2.电气性能检验：检查电控柜内的电气元件和设备连接是否正确，电缆接头是否牢固可靠，线路连接是否无短路、断路等故障，电流、电压和频率是否符合设计要求。

3.环境适应性检验：检查电控柜在不同的温度、湿度和振动环境下的性能表现，确保其能够在各种环境条件下正常运行。

4.安全性检验：检查电控柜的防护等级、绝缘性能和接地状态是否符合国家标准和设计要求，是否存在触电、漏电等安全隐患。

5.功能性检验：检查电控柜中的各项功能是否正常，如断路器的分合闸动作是否灵敏可靠，仪表、指示灯和报警器的使用是否准确可靠等。

三、检验方法1.目测检查：通过对电控柜外观的观察和检查，发现外观缺陷和连接线路错误等问题。

2.电气参数测量：借助于电流表、电压表和多功能仪等工具，测量电控柜内部电流、电压和频率等参数，判断其是否符合设计要求。

3.试验仪器检测：使用万用表、绝缘电阻测试仪和接地电阻测试仪等工具，对电控柜的绝缘性能和接地状态进行检测。

4.功能性测试：通过模拟实际使用情况，对电控柜中的各项功能进行测试，查看是否正常工作。

四、检验结果经过检验，本次出厂的电控柜共检测出以下问题：1.外观方面：部分表面涂装存在不均匀、划痕和锈蚀现象，需要重新处理。

2.电气性能方面：电缆接头存在松动现象，需要加强固定；部分线路连接存在短路和断路，需要重新连接。

3.安全性方面：部分绝缘材料存在老化和损坏现象，需要更换；接地电阻超出标准范围，需要重新接地。

4.功能性方面：部分断路器分合闸动作不灵敏，需要调试竣工。

五、处理措施1.外观问题：重新进行喷涂和抛光处理，确保表面涂装均匀无划痕。

低压配电柜检验报告单

30V＜Ui≤600V
30V＜Ui≤600V
1min无闪络或击穿
低压耐压机
合格
主电路各相之间
合格
辅助电路与地之间
合格
绝艳手柄与地之间
1min无闪络或击穿
合格
3
机械和电气操作试验
机械操作试验
通过设计规定的电压按原理图模拟动作试验，手动、电动操作各5次无异常现象出现。
手动通电调试
合格
合格
电气操作试验
合格
合格
搭接处
铜排接触面平整光滑，无毛刺
塞尺
合格
装配
外观
元件符合图纸要求，紧固件无松动，铭牌正确，接地标记齐全。
目测
合格
主回路间隙（mm）
电气间隙≥10
卷尺
合格
爬电距离≥12
二次配线
连接牢固，端头有标志，敷设应层次分明，牢固。横平竖直，颜色符合设计要求。
目测
合格
2
介电强度
带电部件与地之间
60V＜Ui≤300V 2kv
低压配电柜实验报告单
项目名称:永城市2015年小型农田重点县项目第三标段（电力工程）产品型号:GGD编号：27#
检验项目
技术要求
检验方法
检验结果
1
一般检验
壳体
面门平整，门开启角度不小于90度。排列整齐，焊缝光洁。mm的涂层脱落或划伤
合格
母线
外观
相序正确，相位标识齐全正确，表面平整，防止电措施良好。
合格
合格
4
保护电路连续性试验
主接地点与保护电气外壳接地点电阻值＜10mΩ
双臂电桥
合格
5
功能单元互换性试验
抽出插入，分合闸，联锁试操作各5次，相同单元互换试验满足以上要求

配电箱出厂检验报告

卡尺目测
校验机
符合符合符合符合
3、开关开通，脱扣器在额定电气参数范围内正常工作。
合格合格合格合格合格合格合格
合格合格
共二页、第一页
配电柜出厂检验报告
产品名称：配电控制柜型号规格：800*600*300
出厂编号：FJSHKJ-004 用户名称：
序号
检验项目
技术要求
检验方法及设备
检验项目技术要求检验结果结论框架目测符合合格镀层符合合格外观符合合格外观目测符合合格卡尺符合合格二次配线目测符合合格带电部件与地之间耐压测试仪符合合格主电路各相之间辅助电路与地之间手动操作试验符合合格电气动作试验校验机符合合格共二页第一页配电柜出厂检验报告用户名称
配电柜出厂检验报告
产品名称：配电控制柜型号规格：800*600*300
验
绝缘手柄Байду номын сангаас带电部件之间
3.75KV/1min无击穿闪络
耐压测试仪
1、保证电器正常，分，机构运动灵活，无卡滞及操作力过
手动操作试大现象。
验
机械
2、元器件的各组机械尺寸应符合各自的技术要求。
各电
3 气操作试
1、触头接触良好，机构运动灵活，指示正确。
验
电气动作试验
2、动作符合设计要求。操作5次无异常现象出现。
不小于6mm，爬电距离不小于8mm。
目测卡尺
符合符合
二次配线
1、连接牢固，端头有标志，敷设应层次分明，牢固，整平，竖直，颜色符合设计要求。
目测
带电部件与地之间
2500V/1min无击穿闪络
介
电主电路各相之间 2500V/1min无击穿闪络

配电柜出厂检验报告

质检综合结论：
检验部门：
质检人：
检验日期：
性能
参数
1、变频器、软启动器、热继电器、时间继电、仪表等参数必须按所需功能设定。
合格/不合格
品牌检验
1、元件器品牌型号应与图纸或者报价单一致。
合格/不合格
包
装
1、编号管、图纸、安装附件应齐全。
合格/不合格
2、柜面、显示部分或突出部分应有保护措施。
合格/不合格
3、包装应有方向说明及注意事项。
合格/不合格
合格/不合格
保护电
路的连
续性
1、主接地线与门（箱体）之间的的连续性试验，接地电阻<Q，试验电流为》10A
合格/不合格
2、主接地线与柜体裸露导电部件之间，接地电阻<
Q，试验电流为》10A。
合格/不合格
通电
测试
1、按装置的电气原理图要求进行模拟动作试验，试验结果应符合要求，5次以上均正常动作。
合格/不合格
2、安装置的电气原理图要求进行故障模拟试验，其故障信号和报警指示应正确。
合格/不合格
3、通电试验时每个回路的一、二次接线均正确无误。
合格/不合格
4、各回路开关的容量应与图纸相符。
合格/不合格
ห้องสมุดไป่ตู้显示
指示
1、各种标签标识必须与图纸、工艺测试指示相吻合。
合格/不合格
2、同一设备不冋标示、指示应协调一致。
合格/不合格
电控柜验收报告
柜体名称
柜体规格
柜体类型
柜体数量
项目
检验项目及技术要求
检验结果
备注
绝缘
测试
1、相间电阻、及相线与中线电阻应大于500MQ。

配电柜出厂检验分析报告

合格/不合格
质检综合结论：
检验部门：
质检人：
检验日期：
合格/不合格
2、安装置的电气原理图要求进行故障模拟试验，其故障信号和报警指示应正确。
合格/不合格
3、通电试验时每个回路的一、二次接线均正确无误。
合格/不合格
4、各回路开关的容量应与图纸相符。
合格/不合格
显示
指示
1、各种标签标识必须与图纸、工艺测试指示相吻合。
合格/不合格
2、同一设备不同标示、指示应协调一致。
合格/不合格
性能
参数
1、变频器、软启动器、热继电器、时间继电、仪表等参数必须按所需功能设定。
合格/不合格
品牌检验
1、元件器品牌型号应与图纸或者报价单一致。
合格/不合格
包
装
1、编号管、图纸、安装附件应齐全。
合格/不合格
2、柜面、显示部分或突出部分应有保护措施。
合格/不合格
3、包装应有方向说明及注意事项。
电控柜验收报告
项目名称：编号：
柜体名称
柜体规格检验项目及技术要求
检验结果
备注
绝缘
测试
1、相间电阻、及相线与中线电阻应大于500MΩ。
合格/不合格
耐压
测试
1、主电路带电部件与地（框架）之间，2500V在5秒无击穿、无闪络现象。
合格/不合格
2、主电路母排各相之间，2500V5秒无击穿、无闪络。主回路导线之间，750V5秒无击穿、无闪络，二次回路500V5秒无击穿、无闪络。
合格/不合格
保护电路的连续性
1、主接地线与门（箱体）之间的的连续性试验，接地电阻<0.1Ω，试验电流为》10A
合格/不合格