NOV井下工具简介-中英文
钻井设备及工具中英文对照
钻井设备及工具中文名称English name中文名称English name 储能器accumulator刮管器casing scraper循环池active tank套管鞋casing shoe（刹把）调节螺栓adjusting bole套管卡瓦casing slip进气管admission pipe套管打捞矛casing spear搅拌器agitator套管四通casing spool空气包air chamber套管大钳casing tong气管线air line锚头绳cat line气动绞车air-operated hoist锚头绳爪cat line grip交流电驱动alternating current drive锚头轴cat shaft环形BOP annular BOP锚头cat-head消音器ato-muffler井口甲板cellar deck水泥cement球阀ball valve水泥伞cement basket井口喇叭管bell nipple水泥塞cement plug老虎钳bench vise水泥阻流环cement retainer钻头bit固井质量检查cementing bond log钻头装卸器bit breaker水泥头cementing head钻头规bit gauge固井管线cementing line盲板防喷器blind ram preventer固井泵cenmenting pump剪切闸板防喷器blind shear ram preventer链chain防喷器blow-out preventer链钳chain pipe tong螺栓bolt链钳chain tong防喷器控制盘BOP control pannel房间，寝室chamber防喷器平台BOP deck阀箱，闸室chamber gate底塞bottom plug灌注泵charge pump母扣box止回阀、回压凡尔check valve刹把brake level(brake handle)节流阀、阻流器choke刹带brake line (brake staple)阻流管线choke line桥塞bridge plug节流阀位置指示器choke position indicator 梯形扣buttress节流阀choke valve蝶阀butterfly valve阻流管汇choke-line manifold旁通by-pass离合器clutch旁通塞by-pass plug导管conductor牙轮cone卡钳callipers牙轮打捞器cone fisher套管打捞筒casing bowl牙轮卡死cone lock套管接箍casing coupling冷却水泵cooling-water pump套管隔刀casing cutter取心筒鞋core barrel shoe套管吊卡casing elevator取心爪core basket套管悬挂器casing hanger取心钻头core bit套管头casing head岩心爪core catcher套管平台casing monkey board 岩心爪外套core catecher case岩心烘箱core drying oven 外部割刀external cutter变换接头crossover joint(x/o)吊耳、吊环eye plate天车crown block绳套、接环eye splice天车梁crown block beam灌泥浆管线fill up line死绳dead line失水测定仪filtration test apparatus死绳固定器膜片dead line diaphragm指梁finger board死绳固定器dead line anchor打捞钩fishing hook除气器degasser打捞头fishing head井架derrick打捞震击器fishing jars除砂（泥）器desander(desilter)打捞颈fishing neck直流电驱动direct current drive打捞公锥fishing nipple排出管线discharge line打捞作业sishing operation排出阀discharge valve打捞母锥fishing socket双闸板防喷器double ram type preventer打捞矛fishing spear入井工具down hole tool打捞管柱fishing string绞车draw works打捞公锥fishing tap(taper)绞车电机drawworks motor打捞工具fishing tool通径规drift mandrel法兰flange钻铤drill collar扁锉flat(round,square)file钻铤卡瓦drill collar slip扁嘴钳flat bit tongs钻杆drill pipe平地铣鞋flat bottom mill钻杆卡瓦drill pipe slip绕性接头flexible joint钻杆刮泥器drill pipe wiper 浮鞋float shoe钻柱drill string浮阀float valve司钻控制台driller's console浮箍floating collar司钻监视器driller's monitor四通阀four-way valve钻井大绳drilling line(workline)卡点测定仪free point indicator钻杆防喷器drilling stem valve贯眼钻杆接头full hole joint驱动轴drive shaft漏斗粘度计funnel viscometer从动轴driven shaft传动链条driving chain 储气筒gas holdre(tank)滚筒drum大门gate滚筒容量drum capacity闸门阀gate valve滚筒离合器drum clutch鹅颈管goose neck pipe滚筒高速（低速）drum hight air clutch空气离合器drum low air clutch锤子hammer分级箍DV collar加重钻杆heavey weight drill pipe厚壁钻杆heavy wall drill pipe涡磁刹车eddy current brake高压管线hagh pressure line吊卡elevator开眼器hole opener吊卡耳环elevator link大钩hook吊卡-卡盘elevator-spider大钩弹簧hook spring应急牙嵌离合器emergency jaw clutch水龙带hose（刹带的）平衡杠equalizing yoke卸扣液缸hydraulic break-out cylinder 外卡钳external cutter液压锚头hydraulic catwork液压泵hydraulic pump上扣猫头make out catchead液压油箱hydraulic reserviur手摇钻manual drill液压大钳hydraulic tibg手动阀manual valve液动阀hydraulic valve转盘大补心master bushing液动试压泵hydraulic (press)test pump铣鞋millingshoe液压绞车hydraulic-powered winch铣具milling tool混合漏斗mixing hopper惯性inertia混合泵mixing pump惯性刹车inertia brake猴台monkey board入口inlet电机，马达motor内岩心筒inner core barrel小鼠洞mouse hole中间套管intermediate casing泥浆比重计mud balance钻刚内防喷器intermnal blowout preventer泥浆清洁器mud cleaner内卡钳internal callipers泥浆槽mud ditch内外加厚internal external upset挡泥板mud guard内平钻杆接头internal flush joint泥浆枪 mud gun泥浆泵mud pump震击器jar泥浆泵安全阀mud relieg valve牙嵌离合器jaw cluth泥浆返出管线mud rutern line接头，单根joint泥浆池mut pit笼式打捞篮junk basket打捞爪junk catcher钉子nail打捞杯junk sub近钻头扶正器near-bit stabilizer针形阀needle valve方补心kelly bushing扳手加长套筒nigger-head方钻杆考克kelly cock镊子nipper方保接头kelly pretective sub非磁钻铤non-magnetic drilling collar 方钻杆旋转短节kelly spinner常闭阀normal close valve键槽破坏器key seat reamer常开阀normal open valve压井管线kill line水眼nozzle弯管knee pipe螺帽nut带帽螺栓nut bolt梯子laddre自动螺母扳手nut spinner水平仪level提伸短节listing plug油位oil level滑车装绳数lifting sub油位检查丝堵oil level check plug缸套line reeving油柜oil tank尾管liner油尺oil-level dipstick锁紧螺栓liner开口扳手open-ended spanner锁紧法兰lock bolt外岩心筒outer core barrel低压管线locking flange出口outlet润滑油泵low pressure line加油孔lube oil pump油漆刷paint brush磁力打捞工具lubrication hole领眼钻头pilot bit公扣pin卸扣猫头magnetic fishing tool销子pin钳子pincers螺钉screw撬杠pinch bar螺丝刀screw driver活塞piston无缝钢管seamless pipe活塞皮碗piston up立根盒容量setback capacity活塞杆piston rod沉砂池setting pit手钳子pliers轴shaft旋塞阀plug valve振动筛shalc shaker气动工具pneumatic tool减震器shock absorber硅酸盐水泥portland cement 倒开门吊卡side door elevator动力卡瓦power slip单根吊卡single join elevator动力供应设备power supply unit单闸阀防喷器single ran type preventer 动力大钳power tong计算尺slide rule动力扳手power wrench管钳slide tongs缓冲罐pressure snubbling tank吊索sling生产层套管production casing卡瓦slip滑轮pulley卡瓦补心slip bushing反循环接头pump-out reversing sub卡瓦牙板slip dog短钻杆pup pipe joint 卡瓦槽slip groove卡瓦牙slip insert快速联结quikck connection 卡瓦打捞筒slip socket(卡瓦)锥形座slip socket bowl（井架大门处）坡板ramp套筒扳手socket大鼠洞rat hole卡盘spider正规钻杆接头regular tool joint螺旋钻铤spiral drill collar调节阀regulator valve钢丝绳打捞钩spud spear放压管线relief line开眼钻头spudding bit承托环retaining ring (support ring)插入式注水泥stab-in cementing反循环阀reverse circulation valve对扣台（下套管用）stabbing board反循环打捞篮reverse circulation junk basket扶正器stabilizer反循环孔reverse circulation port不锈钢stainless steel导档齿轮reverse gear立管stand pipe倒扣工具reversing tool插人头stinger钢圈ring gasket（内管）注水泥管柱stinger strings梅花扳手ring spanner双端螺栓stud铆钉river双头螺栓stud bolt转盘rotary table盘根盒stuffing box转盘电机rotary table motor 接头sub转盘风机rotary table motor blower 吸入管线suctionline吸入阀suction valve安全卡瓦safety clamp(slips)表层套管surface casing安全接头safety jont水龙头swivel安全限位档块safety stop安全开关safety switch卷尺tape measure安全带safty -strap(belt)三通tee捞砂滚筒sand reel丝扣thread筛布screen cloth丝扣油thread dope护丝thread protector先行水ahead water三牙轮钻头three-cone bit环空流速annular velocity大钳tong表观黏度apparent viscosity大钳平衡器tong bucket倒扣back off大钳牙板tong dies回压back pressure钳头tong head打好背钳back up attachment大钳刻痕tong mark泥包ball up大钳搭绞部位tong space压舱水ballast water工具接头tool joint尾水behind water工具钢tool steel宾汉模型bingham model顶（底）塞top(bottom) plug钻头成本bit cost水泥面top of the cement钻头直径bit diameterTOTCO承托环TOTCO ring baffle plate 钻头进尺bit footage游动滑车traveling block钻头IADC编码bit IADC code泥浆计量罐trip-tank钻头寿命bit lift两通阀two way valve钻头位置bit position钻头系列号bit series number井架大门v-door钻头齿bit teeth阀门valve钻头时间bit time阀，凡尔valve钻头类型bit type凡尔体valve body钻头磨损bit wear阀盖，阀帽valve bonnet吹扫作业blow job凡尔座balve cup(seat)扫线用管线blow line阀面valve face吹压压力blowing pressure阀杆valve lever井喷blowout阀密封valve seal 防喷bolwout control起阀座器valve seat grab防喷设备blowout control equipment 阀弹簧valve spring装卸防喷器BOP handling灵敏指针vernier沉砂bottom fill虎钳vice(=vise)井底压力bottom-hole pressure双母接头box-box connection壁钩wall hook套管程序casing program冲管wash pipe套管尺寸casing size耐磨补心wear bushing阳离子表面活性剂cationic surface active agent 井口装置well-head equipment烧碱caustic soda造斜器whip stock水泥胶结cement bond翼状扶正器wing stabilizer水泥串槽cement channeling 20"“ L”型接头type "l" connector固井失败cement failure水泥冲洗cement flush水泥浆cement slurry固井配方cementing formulation循环circulation粘土泥浆clay base mud控制钻进control drilling岩心取样coring sample腐蚀corrosion临界速度critical velocity气显示gas showing天车防碰装置crown block protector硬地层hard formation天车防碰装置crown block saver井眼尺寸hole size割大绳cut off drilling line井眼纠斜hole straightening危险品danderous objects大钩负荷hook load除垢剂degasser efficiency大钩位置hook position井斜测量deviation survey初切力initial gel-strength压差卡钻differential pressure sticking内管注水泥inner string cementing定向钻井directional drilling表面活性剂interface level indicator定向井directional well方入kelly down狗腿dog leg方入深度kelly dowm depth狗腿率dog leg ratio方入kelly in停工时间down time方余kelly up通径drifting键槽卡钻key-seating sticking钻具组合drilling assembly井涌kick钻进突变drilling break 控制井涌kick control钻进承包商drilling contractor压井kill well钻井成本drilling cost甩钻杆lay down the drill pipe钻进时间drilling hours漏失实验leak-offtest钻井作业drilling operation左旋“J”型槽left-hand J-slot钻井程序drilling preogram迟到时间log time钻井报表drilling report低固相泥浆low solid mud钻井日报drilling daily report最小速度maximum pressure钻井水drilling water平均海平面maximum speed钝钻头分级dull bit grading平均潮面mean sea level戴纳钻具dyna-drill泥浆添加剂mean tide level乳化剂emulsifying agent泥浆柱mud additive刺坏erode out泥浆柱mud column评估井evaluation well调节泥浆mud conditioning初探井exploratory well泥浆处理材料mud conditioning materials 疲劳极限fatigue limit泥线mud line自动灌浆浮鞋fill-up float shoe泥浆录井mud logging泥饼filter cake泥浆量mud volume降失水剂filtration-reducing agent不漏no leak絮凝作用flocculation无返出no return流压flowing pressure水眼效率nozzle efficiency失水fluid loss水眼尺寸nozzle size地层formation离开井底off-bottom地层测试formation test海上offshore地层水formation wter漏油oil leak淡水fresh water油层压力oil reservoir pressure功能测验function test耐油橡胶oil resistant gom气含量gas content油封oil seal气侵gas cut油页岩oil shale泥浆中的气gas in mud油基泥浆oil-base mud气层gas reservoir接触井底on bottom裸眼open hole开钻spud in作业者operator开钻泥浆spud mud上提，遇卡overpull挤水泥squeeze cement上扣过紧overtonging分级注水泥squeeze cementing钟摆钻具组合pendulum bottom hole assembly待命stand-by机械钻速penetration rate待命费stand-by rate塑性黏度plastic viscosity启动（泵）start ip(pump)塑料plastics静压static pressure水泥回堵plugging back卡钻sticking管内压降pressure loss in pipe卡点sticking point压力试验pressure test泵冲stoke泵入水泥塞pump down plug抽吸压力swab pressure泵效pump efficiency抽吸swabbing泵压pump pressure 转盘高度table height泵速pump speed转盘扭矩table torque泵冲pump stroke试纸test paper额定流量rated flow绸化时间thicking time划眼reaming错扣thread alternating记录record造扣thread making记录纸recording paper脱扣thread off松开捞矛releasing spear滑扣thread slipping缓凝剂retarder缩径井眼tight hole反循环reverse circulation大钳扭矩tong torque钻台rig floor起下钻trip转盘转速fotary speed起下钻时间tripping time下套管run casing事故troubles运转时间running time垂深vertical depth下入工具running tool增稠剂viscosifier砂桥sand bridge侯凝wait on cementing饱和盐水泥降saturated salt-water mud壁厚wall thickness晕船sea sick开泵循环下放wash dowm海水泥浆seawater mud冲刷井段wash out section坐卡瓦setting slip水击water hammer浅层气shallow gas钻压weight on bit泥质砂岩shaly sand加重材料weighting materials短起下short trip井口流压well head flow pressure 关井shut-in井位well location关井套压shut-in casing pressure通井wiper trip关井钻杆压力shut-in drill pipe pressure作业指令working instruction请病假sick leave工作压力working pressure侧钻side tracking倒大绳slip drilling line坍塌sloughing ,caving苏打soda软地层soft formation固相含量solid content锚anchor救生圈life buoy抛锚船anchor boat救生衣life jacket风速表anemometer救生艇lifeboat重晶石barite照明lighting气压计barometer水位报警器liquid level alarm般土bentonite定位浮标locating buoy锅炉boiler人孔、检修孔manhole爬杆boom人孔盖manhole cover防喷演习BOP drill指示灯、标志灯marker lamp手提式CO2灭火器CO2 hand-portable fire-extingusisher隔膜泵membrane pump空压机compressor锚泊系统mooring system冷凝器condenser马达油motor oil吊车crane拖航灯navigation lights甲板deck空载、空车no load柴油机diesel engine障碍灯obstruction light吃水线draft line超载overload电动机electrical motor泥浆池测定演习pit drill排烟管engine exhaust line 可移动式1211灭火器portable 1211 extinguisher柴油engine oil手提式干粉灭火器portable dry powder fire extinguisher 逃生呼吸器escape bresthing apparatus生活水（淡水）portable water (fresh water)传真facsimile压载水preload water消防报警系统fire alarm system压载preloading消防演习fire drill通风设备rrentilation太平门fire escape软（绳）梯rope laddre消防斧fire hatchet接线盒rosette消防管线fire line安全网safety net消防面罩fire mask卫生水管线sanitary line消防服fireman's suit海水淡化装置swawater distillation unit急救设备first-aid equipment海水管线seawater line急救箱first-aid kit分离器seperator泡沫灭火系统foam fire extinguishing sysem值班船stand-by boat燃油（柴油）fuel(diesel oil)担架stretcher防毒面具gas mask潜水泵submerged pump发电机generator救生服survival suit砂轮机grinder电话telephone硫化氢气体检测系统H2S gas detection system电传打字机teletype热交换器heat exchanger电传打字电报telex加热盘管heating coil试运转、试车test run直升机平台helicopter port温度计thermometer可膨胀式救生阀inflatable liferaft可控硅thyristor升降室jack house计时器、秒表timer升船jacking 气焊torch升降系统jacking system拖缆towing line信号、信号灯lantern收发报机transceiver车床lathe变压器transformer桩腿leg打字机typewriter卸载unload可变载荷variable load排气孔vent hole电焊条welding electrode绞盘、绞机windlass工作救生衣work life jacket气压表air pressure gauge流量警报器flow alarm流量指示器flowing indicator流量计flowing meter泥浆流量计mud flow meter泥浆体积指示器mud volume indicator 油压表oil pressure guage泥浆液位计pit level meter位置指示器position indicator压力表pressure gauge泵冲数计数器pump stroke counter 泵冲数指示器pump stroke indicator 泵冲数传感器pump stoke sensor转盘转速表rotary speed indicator 转盘扭矩表rotary torque indicator 灵敏度sensitivity指重表weight indicator。
钻井设备及工具中英文对照ok
钻井设备及工具序号名称英文1海水泥浆seawater mud2开钻spud in3（井架大门处）坡板ramp4(卡瓦)锥形座slip socket bowl5（内管）注水泥管柱stinger strings6（刹把）调节螺栓adjusting bole7（刹带的）平衡杠equalizing yoke 820"“ L”型接头type "l" connector9TOTCO承托环TOTCO ring baffle plate 10安全带safty -strap(belt)11安全接头safety jont12安全卡瓦safety clamp(slips) 13安全开关safety switch14安全网safety net15安全限位档块safety stop16扳手加长套筒nigger-head17般土bentonite18饱和盐水泥降saturated salt-water mud 19泵冲pump stroke20泵冲stoke21泵冲数传感器pump stoke sensor 22泵冲数计数器pump stroke counter 23泵冲数指示器pump stroke indicator 24泵入水泥塞pump down plug25泵速pump speed26泵效pump efficiency27泵压pump pressure28壁钩wall hook29壁厚wall thickness30扁锉flat(round,square)file 31扁嘴钳flat bit tongs32变换接头crossover joint(x/o) 33变压器transformer34表层套管surface casing35表观黏度apparent viscosity 36表面活性剂interface level indicator 37宾汉模型bingham model38不漏no leak39不锈钢stainless steel40侧钻side tracking41插人头stinger42插入式注水泥stab-in cementing43柴油engine oil44柴油机diesel engine45常闭阀normal close valve46常开阀normal open valve47超载overload48车床lathe49沉砂bottom fill50沉砂池setting pit51承托环retaining ring (support ring) 52吃水线draft line53迟到时间log time54冲管wash pipe55冲刷井段wash out section56抽吸swabbing57抽吸压力swab pressure58绸化时间thicking time59出口outlet60初切力initial gel-strength61初探井exploratory well62除垢剂degasser efficiency63除气器degasser64除砂（泥）器desander(desilter)65储能器accumulator66储气筒gas holdre(tank)67传动链条driving chain68传真facsimile69吹扫作业blow job70吹压压力blowing pressure71垂深vertical depth72锤子hammer73磁力打捞工具lubrication hole74刺坏erode out75从动轴driven shaft76错扣thread alternating77打好背钳back up attachment78打捞杯junk sub79打捞工具fishing tool80打捞公锥fishing nipple81打捞公锥fishing tap(taper)82打捞钩fishing hook83打捞管柱fishing string84打捞颈fishing neck85打捞矛fishing spear86打捞母锥fishing socket87打捞头fishing head88打捞震击器fishing jars89打捞爪junk catcher90打捞作业sishing operation91打字机typewriter92大钩hook93大钩弹簧hook spring94大钩负荷hook load95大钩位置hook position96大门gate97大钳tong98大钳搭绞部位tong space99大钳刻痕tong mark100大钳扭矩tong torque101大钳平衡器tong bucket102大钳牙板tong dies103大鼠洞rat hole104带帽螺栓nut bolt105待命stand-by106待命费stand-by rate107戴纳钻具dyna-drill108单根吊卡single join elevator 109单闸阀防喷器single ran type preventer 110担架stretcher111淡水fresh water112挡泥板mud guard113导档齿轮reverse gear114导管conductor115倒大绳slip drilling line 116倒开门吊卡side door elevator 117倒扣back off118倒扣工具reversing tool119低固相泥浆low solid mud 120低压管线locking flange 121底塞bottom piug 122地层formation 123地层测试formation test 124地层水formation wter 125电传打字电报telex126电传打字机teletype127电动机electrical motor 128电焊条welding electrode 129电话telephone 130电机，马达motor131吊车crane132吊耳、吊环eye plate133吊卡elevator134吊卡耳环elevator link 135吊卡-卡盘elevator-spider 136吊索sling137调节阀regulator valve 138调节泥浆mud conditioning 139蝶阀butterfly valve 140钉子nail141顶（底）塞top(bottom) plug 142定位浮标locating buoy 143定向井directional well 144定向钻井directional drilling 145动力扳手power wrench 146动力大钳power tong 147动力供应设备power supply unit 148动力卡瓦power slip 149短起下short trip 150短钻杆pup pipe joint 151对扣台（下套管用）stabbing board 152钝钻头分级dull bit grading 153鹅颈管goose neck pipe 154额定流量rated flow 155发电机generator 156阀，凡尔valve157阀弹簧valve spring 158阀盖，阀帽valve bonnet159阀杆valve lever160阀门valve161阀密封valve seal162阀面valve face163阀箱，闸室chamber gate164法兰flange165凡尔体valve body166凡尔座balve cup(seat)167反循环reverse circulation168反循环打捞篮reverse circulation junk basket 169反循环阀reverse circulation valve 170反循环接头pump-out reversing sub 171反循环孔reverse circulation port 172方保接头kelly pretective sub173方补心kelly bushing174方入kelly down175方入kelly in176方入深度kelly dowm depth177方余kelly up178方钻杆考克kelly cock179方钻杆旋转短节kelly spinner180防毒面具gas mask181防喷bolwout control182防喷器blow-out preventer183防喷器控制盘BOP control pannel184防喷器平台BOP deck185防喷设备blowout control equipment 186防喷演习BOP drill187房间，寝室chamber188放压管线relief line189非磁钻铤non-magnetic drilling collar 190分级箍DV collar191分级注水泥squeeze cementing192分离器seperator193风速表anemometer194扶正器stabilizer195浮阀float valve196浮箍floating collar197浮鞋float shoe198腐蚀corrosion199缸套line reeving200钢圈ring gasket201钢丝绳打捞钩spud spear202高压管线hagh pressure line 203割大绳cut off drilling line 204隔膜泵membrane pump 205工具钢tool steel206工具接头tool joint207工作救生衣work life jacket208工作压力working pressure 209公扣pin210功能测验function test211狗腿dog leg212狗腿率dog leg ratio213固井泵cenmenting pump 214固井管线cementing line215固井配方cementing formulation 216固井失败cement failure217固井质量检查cementing bond log 218固相含量solid content219刮管器casing scraper220关井shut-in221关井套压shut-in casing pressure 222关井钻杆压力shut-in drill pipe pressure 223管内压降pressure loss in pipe 224管钳slide tongs225贯眼钻杆接头full hole joint226惯性inertia227惯性刹车inertia brake228灌泥浆管线fill up line229灌注泵charge pump230硅酸盐水泥portland cement 231滚筒drum232滚筒高速（低速）drum hight air clutch 233滚筒离合器drum clutch234滚筒容量drum capacity235锅炉boiler236海上offshore237海水淡化装置swawater distillation unit 238海水管线seawater line239侯凝wait on cementing 240猴台monkey board241厚壁钻杆heavy wall drill pipe 242虎钳vice(=vise)243护丝thread protector 244滑车装绳数lifting sub245滑扣thread slipping246滑轮pulley247划眼reaming248环空流速annular velocity 249环形BOP annular BOP250缓冲罐pressure snubbling tank 251缓凝剂retarder252回压back pressure253混合泵mixing pump254混合漏斗mixing hopper255活塞piston256活塞杆piston rod257活塞皮碗piston up258机械钻速penetration rate259急救设备first-aid equipment 260急救箱first-aid kit261挤水泥squeeze cement262计时器、秒表timer263计算尺slide rule264记录record265记录纸recording paper266加热盘管heating coil267加油孔lube oil pump268加重材料weighting materials 269加重钻杆heavey weight drill pipe 270甲板deck271减震器shock absorber272剪切闸板防喷器blind shear ram preventer 273键槽卡钻key-seating sticking 274键槽破坏器key seat reamer275降失水剂filtration-reducing agent 276交流电驱动alternating current drive 277绞车draw works278绞车电机drawworks motor279绞盘、绞机windlass280搅拌器agitator281接触井底on bottom282接头sub283接头，单根joint284接线盒rosette285节流阀choke valve286节流阀、阻流器choke287节流阀位置指示器choke position indicator 288近钻头扶正器near-bit stabilizer 289进气管admission pipe 290井底压力bottom-hole pressure 291井架derrick292井架大门v-door293井口甲板cellar deck294井口喇叭管bell nipple295井口流压well head flow pressure 296井口装置well-head equipment 297井喷blowout298井位well location299井斜测量deviation survey 300井眼尺寸hole size301井眼纠斜hole straightening 302井涌kick303静压static pressure304救生服survival suit305救生圈life buoy306救生艇lifeboat307救生衣life jacket308卷尺tape measure309卡点sticking point310卡点测定仪free point indicator 311卡盘spider312卡钳callipers313卡瓦slip314卡瓦补心slip bushing315卡瓦槽slip groove316卡瓦打捞筒slip socket317卡瓦牙slip insert318卡瓦牙板slip dog319卡钻sticking320开泵循环下放wash dowm321开口扳手open-ended spanner 322开眼器hole opener323开眼钻头spudding bit324开钻泥浆spud mud325可变载荷variable load326可控硅thyristor327可膨胀式救生阀inflatable liferaft328可移动式1211灭火器portable 1211 extinguisher 329空气包air chamber330空气离合器drum low air clutch 331空压机compressor332空载、空车no load333控制井涌kick control334控制钻进control drilling335快速联结quikck connection 336捞砂滚筒sand reel337老虎钳bench vise338冷凝器condenser339冷却水泵cooling-water pump 340离合器clutch341离开井底off-bottom342立根盒容量setback capacity343立管stand pipe344链chain345链钳chain pipe tong346链钳chain tong347两通阀two way valve348临界速度critical velocity349灵敏度sensitivity350灵敏指针vernier351领眼钻头pilot bit352流量计flowing meter353流量警报器flow alarm354流量指示器flowing indicator 355流压flowing pressure356硫化氢气体检测系统H2S gas detection system 357笼式打捞篮junk basket358漏斗粘度计funnel viscometer359漏失实验leak-offtest360漏油oil leak361螺钉screw362螺帽nut363螺栓bolt364螺丝刀screw driver365螺旋钻铤spiral drill collar366裸眼open hole367马达油motor oil368盲板防喷器blind ram preventer 369锚anchor370锚泊系统mooring system371锚头cat-head372锚头绳cat line373锚头绳爪cat line grip374锚头轴cat shaft375铆钉river376梅花扳手ring spanner377母扣box378内管注水泥inner string cementing 379内卡钳internal callipers380内平钻杆接头internal flush joint 381内外加厚internal external upset 382内岩心筒inner core barrel383耐磨补心wear bushing384耐油橡胶oil resistant gom385泥包ball up386泥饼filter cake387泥浆泵mud pump388泥浆泵安全阀mud relieg valve389泥浆比重计mud balance390泥浆槽mud ditch391泥浆池mut pit392泥浆池测定演习pit drill393泥浆处理材料mud conditioning materials 394泥浆返出管线mud rutern line395泥浆计量罐trip-tank396泥浆量mud volume397泥浆流量计mud flow meter398泥浆录井mud logging399泥浆枪 mud gun400泥浆清洁器mud cleaner401泥浆体积指示器mud volume indicator 402泥浆添加剂mean tide level403泥浆液位计pit level meter404泥浆中的气gas in mud405泥浆柱mud additive406泥浆柱mud column407泥线mud line408泥质砂岩shaly sand409镊子nipper410爬杆boom411排出阀discharge valve412排出管线discharge line413排气孔vent hole414排烟管engine exhaust line415盘根盒stuffing box416旁通by-pass417旁通塞by-pass plug418抛锚船anchor boat419泡沫灭火系统foam fire extinguishing sysem 420疲劳极限fatigue limit421平地铣鞋flat bottom mill422平均潮面mean sea level423平均海平面maximum speed424评估井evaluation well425启动（泵）start ip(pump)426起阀座器valve seat grab427起下钻trip428起下钻时间tripping time429气层gas reservoir430气动工具pneumatic tool431气动绞车air-operated hoist432气管线air line433气含量gas content434气焊torch435气侵gas cut436气显示gas showing437气压表air pressure gauge438气压计barometer439钳头tong head440钳子pincers441潜水泵submerged pump442浅层气shallow gas443桥塞bridge plug444撬杠pinch bar445请病假sick leave446球阀ball valve447驱动轴drive shaft448取心筒鞋core barrel shoe449取心爪core basket450取心钻头core bit451燃油（柴油）fuel(diesel oil)452绕性接头flexible joint453热交换器heat exchanger454人孔、检修孔manhole455人孔盖manhole cover456乳化剂emulsifying agent457入井工具down hole tool458入口inlet459软（绳）梯rope laddre460软地层soft formation461润滑油泵low pressure line462三通tee463三牙轮钻头three-cone bit464扫线用管线blow line465刹把brake level(brake handle) 466刹带brake line (brake staple) 467砂轮机grinder468砂桥sand bridge469筛布screen cloth470上扣过紧overtonging471上扣猫头make out catchead 472上提，遇卡overpull473烧碱caustic soda474升船jacking475升降室jack house476升降系统jacking system477生产层套管production casing478生活水（淡水）portable water (fresh water)479绳套、接环eye splice480失水fluid loss481失水测定仪filtration test apparatus482事故troubles483试运转、试车test run484试纸test paper485收发报机transceiver486手动阀manual valve487手钳子pliers488手提式CO2灭火器CO2 hand-portable fire-extingusisher 489手提式干粉灭火器portable dry powder fire extinguisher 490手摇钻manual drill491甩钻杆lay down the drill pipe492双端螺栓stud493双母接头box-box connection494双头螺栓stud bolt495双闸板防喷器double ram type preventer 496水击water hammer497水龙带hose498水龙头swivel499水泥cement500水泥冲洗cement flush501水泥串槽cement channeling502水泥回堵plugging back503水泥浆cement slurry504水泥胶结cement bond505水泥面top of the cement506水泥塞cement plug507水泥伞cement basket508水泥头cementing head509水泥阻流环cement retainer510水平仪level511水位报警器liquid level alarm512水眼nozzle513水眼尺寸nozzle size514水眼效率nozzle efficiency515丝扣thread516丝扣油thread dope517司钻监视器driller's monitor518司钻控制台driller's console519死绳dead line520死绳固定器dead line anchor521死绳固定器膜片dead line diaphragm 522四通阀four-way valve523松开捞矛releasing spear524苏打soda525塑料plastics526塑性黏度plastic viscosity527缩径井眼tight hole528锁紧法兰lock bolt529锁紧螺栓liner530太平门fire escape531坍塌sloughing ,caving 532逃生呼吸器escape bresthing apparatus 533套管程序casing program534套管尺寸casing size535套管打捞矛casing spear536套管打捞筒casing bowl537套管大钳casing tong538套管吊卡casing elevator539套管隔刀casing cutter540套管接箍casing coupling541套管卡瓦casing slip542套管平台casing monkey board 543套管四通casing spool544套管头casing head545套管鞋casing shoe546套管悬挂器casing hanger547套筒扳手socket548梯形扣buttress549梯子laddre550提伸短节listing plug551天车crown block552天车防碰装置crown block protector 553天车防碰装置crown block saver 554天车梁crown block beam 555停工时间down time556通风设备rrentilation557通井wiper trip558通径drifting559通径规drift mandrel560拖航灯navigation lights561拖缆towing line562脱扣thread off563外部割刀external cutter564外卡钳external cutter565外岩心筒outer core barrel566弯管knee pipe567危险品danderous objects568尾管liner569尾水behind water570卫生水管线sanitary line571位置指示器position indicator572温度计thermometer573涡磁刹车eddy current brake 574无返出no return575无缝钢管seamless pipe576吸入阀suction valve577吸入管线suctionline578铣具milling tool579铣鞋millingshoe580下入工具running tool581下套管run casing582先行水ahead water583消防报警系统fire alarm system584消防服fireman's suit585消防斧fire hatchet586消防管线fire line587消防面罩fire mask588消防演习fire drill589消音器ato-muffler590销子pin591小鼠洞mouse hole592卸扣猫头magnetic fishing tool 593卸扣液缸hydraulic break-out cylinder 594卸载unload595信号、信号灯lantern596絮凝作用flocculation597旋塞阀plug valve598循环circulation599循环池active tank600压舱水ballast water601压差卡钻differential pressure sticking 602压井kill well603压井管线kill line604压力表pressure gauge605压力试验pressure test606压载preloading607压载水preload water608牙轮cone609牙轮打捞器cone fisher610牙轮卡死cone lock611牙嵌离合器jaw cluth612岩心烘箱core drying oven613岩心取样coring sample614岩心爪core catcher615岩心爪外套core catecher case616阳离子表面活性剂cationic surface active agent 617液动阀hydraulic valve618液动试压泵hydraulic (press)test pump 619液压泵hydraulic pump620液压大钳hydraulic tibg621液压绞车hydraulic-powered winch 622液压锚头hydraulic catwork623液压油箱hydraulic reserviur 624翼状扶正器wing stabilizer625应急牙嵌离合器emergency jaw clutch 626硬地层hard formation627油层压力oil reservoir pressure 628油尺oil-level dipstick629油封oil seal630油柜oil tank631油基泥浆oil-base mud632油漆刷paint brush633油位oil level634油位检查丝堵oil level check plug 635油压表oil pressure guage636油页岩oil shale637游动滑车traveling block638运转时间running time639晕船sea sick640造扣thread making641造斜器whip stock642增稠剂viscosifier643闸门阀gate valve644粘土泥浆clay base mud645障碍灯obstruction light646照明lighting647针形阀needle valve648振动筛shalc shaker649震击器jar650正规钻杆接头regular tool joint651直流电驱动direct current drive652直升机平台helicopter port653值班船stand-by boat654止回阀、回压凡尔check valve655指梁finger board656指示灯、标志灯marker lamp657指重表weight indicator658中间套管intermediate casing659中文名称English name660钟摆钻具组合pendulum bottom hole assembly 661重晶石barite662轴shaft663转盘rotary table664转盘大补心master bushing665转盘电机rotary table motor666转盘风机rotary table motor blower 667转盘高度table height668转盘扭矩table torque669转盘扭矩表rotary torque indicator670转盘转速fotary speed671转盘转速表rotary speed indicator672桩腿leg673装卸防喷器BOP handling674自动灌浆浮鞋fill-up float shoe675自动螺母扳手nut spinner676阻流管汇choke-line manifold677阻流管线choke line678钻杆drill pipe679钻杆防喷器drilling stem valve 680钻杆刮泥器drill pipe wiper681钻杆卡瓦drill pipe slip682钻刚内防喷器intermnal blowout preventer 683钻进承包商drilling contractor684钻进时间drilling hours685钻进突变drilling break686钻井报表drilling report687钻井成本drilling cost688钻井程序drilling preogram689钻井大绳drilling line(workline) 690钻井日报drilling daily report 691钻井水drilling water692钻井作业drilling operation693钻具组合drilling assembly694钻台rig floor695钻铤drill collar696钻铤卡瓦drill collar slip697钻头bit698钻头IADC编码bit IADC code699钻头成本bit cost700钻头齿bit teeth701钻头规bit gauge702钻头进尺bit footage703钻头类型bit type704钻头磨损bit wear705钻头时间bit time706钻头寿命bit lift707钻头位置bit position708钻头系列号bit series number709钻头直径bit diameter710钻头装卸器bit breaker711钻压weight on bit712钻柱drill string713最小速度maximum pressure 714左旋“J”型槽left-hand J-slot715作业者operator716作业指令working instruction 717坐卡瓦setting slip。
NationalOilwellVarcoNOV中文译名国民油井华高一贯致力于
国民油井华高 TEL：0595-28767836 15980012163
National Oilwell Varco (NOV, 中文译名：国民油井华高)一贯致力于保证顾客得到最高质量的油田产品与服 务。凭借超过 700 个遍布全球的制造、销售及服务中心，National Oilwell Varco 以顾客为重点，提供能满 足能源工业界对质量、产能和环境要求的最佳解决方案。National Oilwell Varco 是世界上最大的钻井设备制 造商，产品包括陆地和海上钻机的大型机械部件、成套陆地钻机和修井机、管材检测和管内涂层、钻柱设备、 多种起升设备以及各种井下马达、钻头和工具。National Oilwell V，提供供应链服务。 NOV 提供全套的修井及完井服务设备，包括车载修井机、连续油管设备、液氮设备、固井设备、压裂设备和电 缆设备以及井下工具和井口压力控制设备。此外，NOV 提供全系列技术先进的仪表和控制装置 ，大幅提高了作 业安全性，并为用户带来了巨大经济效益。 NOV 产品包括以下品牌：Rolligon、Texas Oil Tools、HydraRig、CTES、Fidmash和Elmar，提供各种品牌装置 设备，这些专业设备可以满足从海上平台到沙漠及极地作业的要求
钻井工具解决方案 National Oilwell Varco提供世界上最全面和最可靠的钻井工具与设备。是唯一一家提供和服务全套井下钻具 总成的独立井下工具制造厂商。公司的产品范围包括： 钻头 钻井马达 动力部分 扩孔器 扩孔工具 扶正器 震击工具 无磁钻井部件 电磁随钻测量（MWD）系统 钻铤 钻井震击器 钻井震击器助力器 钻杆 NOV 提供最广泛最全面的扩孔工具，以经验证的技术满足该行业最复杂、多样与困难的开孔作业要求 。产品包 括固定切削刃钻柱工具、双心钻头和同心井下扩孔器。 修井与完井解决方案
井下工具简介
主体部分为向下开的大V字型开口，下部为空腔， 在KCK-116扶正引鞋上部加装3mφ48mm短接，由 于扶正引鞋的扶偏作用，测试仪器到达泵下即被引 到V字型开口上部，由V字型开口的导向进入扶正引 鞋，在KCK-116扶正引鞋下部加装3mφ88.9mm短 接，使进入扶正引鞋的测试仪器处于自由状态，得 到充分的扶正不会被卡住，保证所有φ28mm以下 3m长的各种测试仪器的顺畅通过。
上提管柱，使解封销钉剪断，继续上提 管柱时，下接头带动锥体上移，使卡瓦 收回，达到解封的目的。
最大外径：116mm；最小通径：76mm； 坐封压力：14-16Mpa；
使用要求及注意事项
作业队完井时，将泵及油管锚下到预定深度后，配井口，要求萝卜头 距四通位置留有0.2-0.25m的高度，油管正打压14-16Mpa，稳压15 分钟后释放MX241型大通径油管锚。 下放油管座萝卜头。从下放油管可以判断油管锚是否锚定住了管柱。 上提管柱解锚。
比例 （% ）
2 4 .4 7
性能评价 洗井后滑套不易归位
263
97-2000年
1 0 .8 9
两级胶筒，密封性能低。易断裂、 损坏
924
2 0 0 2 年开始
3 8 .2 6
来水释放，密封性能好。承压和耐 蠕动能力强。
63 98-2001年 2.61 不可洗井，应用范围受限。
96
3.98 主要存在测试卡阻问题。
194 98年以前 8.03 需存在一定压差才确保其密封
93
191 2415
2000 –2 0 0 1 年
各年均有
3.85 需存在一定压差才确保其密封 7.91
K344-114封隔器
该封隔器为水力扩张式（主要与节 流器或喷砂器配套使用），油管内、外 达到一定压差即可实现座封，无座封锁 定装置，因此泄掉油管内压力，封隔器 就会自动解封。主要用于验窜、找漏及 压裂施工。
完井工具介绍中英文版
Compensation Device 补偿装置
General Description This product is applied in offshore Semi-submersible platform to compensate the tubing expansion or shrinkage caused by seawater fluctuation. This device has a feature of self-equalization, which means it will not be affected by tubing pressure change.
1. The flapper has pressure equalizing type and non-pressure equalizing type; 2. Locking and sealing structure are designed at the upper side; 3. It is highly reliable to use metal to metal sealing style in the sealing chamber; 4. The upper and bottom thread can be adjusted according to clients' requirements.
2、flow couple 流动短节
3、compensation device 补偿装置
4、expansion joint 伸缩节
5、Sliding sleeve 滑套
6、shifting tool 移位器
完井工具介绍中英文版
Tubing Extension Joint 油管伸缩节
General Description: This product is used to compensate the axial expansion or shrinkage of tubing caused by well-treatment, water-injection or temperature changes.This product uses spline pin so that the torque can be transmitted at any position.
1、通过增加和减少剪切销钉调节剪切值； 2、工具可以通过剪切销钉完全锁定在全伸展、全收缩或中间冲 程位置； 3、足够长度的锁键可以提供全冲程扭矩传递； 4、上下连接扣型可以根据客户要求提供。
Tubing Extension Joint 油管伸缩节
Technical Specifications 技术参数
Technical Specifications
Demension
2-3/8 2-3/8 2-7/8 2-7/8 3-1/2 3-1/2 4-1/2 4-1/2 5-1/2 5-1/2
Max OD/in Sealing Bore /in
3.625 3.625 4.625 5.135 5.38 5.65 5.125 7.5 8.375 8.375
SS系列滑套是一种油、套通道的开关控制工具。它是通过标准 的钢丝作业来实现对滑套芯轴的打开与关闭，是一种油、气井 完井中分层开采的工具。
SS Serious Sliding Sleeve SS系列滑套
井下设备介绍
Doe Run, Missouri Martin Marietta, Indianapolis
Savage Zinc Gordonsville, Tennessee Cowin & Company, Tennessee
Weeks Isl8
P.T. Freeport Indonesia Mine
6
Queenstown Cradle Mountain
8
Wineglass Bay
Agriculture
Port of Burnie, Tasmania 塔斯马尼亚州波尼港
9
Company History 公司历史
•1975 DB Elphinstone •1986 First LHD 第一台井下铲运机 •1995 Establishment of CEPL 成立了CEPL
32
P.T. Freeport Indonesia Mine
Model 型号
120H Grader R1500 – 241 R1300 – 920 R2900G R1700 11 R1700G
Numbers 数量
3 1 1 6 7 31
Comments 说明
First Delivered 1998 First Delivered Nov 1996
Holt Mcdermot, Ontario
Inco Sudbury, Ontario
Westmin Campbell River, British Columbia Stillwater Nye, Montana
Mine Seleine, Quebec Sifto Salt Goderich, Ontario Canada Salt Windsor, Ontario American Rock Salt, NYK
NOV
NOV 为快速安装、插入和细管钻具提供可靠的地面和井下设备。
服务设备解决方案
National Oilwell Varco 专门制造井下工具服务设备，无论是组装工具或钻具接头的上御扣扭矩装置，还是检查作业及性能发挥的测试台，都属于本公司的产品范围。
National Oilwell Varco 作为井下工具与设备的世界领军企业，提供具有先进技术、精益制造和可靠质量的井下工具，并提供NOV 再认证及年度保养维修服务。NOV在80多个国家分布着150 多个作业地点，NOV的全球性的网点分布、无与伦比的井下工具配套和经验丰富的人员配置，使我们能够满足顾客最苛刻的钻井工况需求。
NOV
关于NOV
NOV(National Oilwell Varco)，中文译名：国民油井华高。自1841年以来，NOV一贯致力于保证顾客得到最高质量的油田产品与服务。
凭借超过 700 个遍布全球的制造、销售及服务中心，National Oilwell Varco 以顾客为重点，提供能满足能源工业界对质量、产能和环境要求的最佳解决方案。National Oilwell Varco 是世界上最大的钻井设备制造商，产品包括陆地和海上钻机的大型机械部件、成套陆地钻机和修井机、管材检测和管内涂层、钻柱设备、多种起升设备以及各种井下马达、钻头和工具。National Oilwell Varco 还通过设在世界各主要油气产地的分销服务中心网络，提供供应链服务。
NOV Russell 井下导向工具提供准确与可靠的倾角、方位、压力、温度和钻压信息。NOV 还为选购导向工具的顾客提供产品培训、设备校正、软件开发、工程、测试及产品认证服务。
NOV井下工具产品介绍
制造商 国民油井 旋冲螺杆 HEMIDRIL等壁厚螺杆 Power-plus 高扭螺杆 国内某厂家 常规 等壁厚 低转速高扭矩螺杆 某进口厂家 等壁厚 低转速高扭矩螺杆
该项目使用国民油井5”螺杆44根，从各项使用数据来看，均有很大 优势。
Quadril泥浆润滑螺杆设计特点以及应用优势
螺杆采用泥浆润滑传动轴总成：
钻进 机械钻速 时间
121 40.33 91.7
12.22 12.22 13.98
YS108H11-2
NOV
NOV Fuid Hammer
旋冲钻具部分 弯角/直设计 动力总成
• 与牙轮和PDC钻头都可兼容 • 已被证明可以显著提升钻速 • 与国民油井ST3螺杆轴承总成搭配使用 • 适合多种应用，比如硬地层、页岩、提速需求及定向需求等等
泥浆脉冲向上传播至减震工具
水力振荡器拉力试验
水力振荡器地面测试
开泵后，泥浆脉冲作用在减震工 具上，减震器启动。 产生轴向振动（沿着钻杆钻 具），减少摩擦阻力
Agitator™水力振荡器四川地区部分使用记录
摘自焦页23-3HF井钻井工程师评论
井号 焦页17-3HF 焦页20-2HF 焦页21-3HF 焦页21-3HF 焦页23-1HF 焦页23-3HF 焦页26-2HF 工具尺寸 8” 8” 6-3/4” 8” 8” 8” 8” 客户 江汉钻井一公司 中原西南钻井分公司 中原钻井四公司 中原钻井四公司 中原钻井一公司 中原钻井一公司 中原钻井二公司 使用时间 2014年4月 2014年3月 2014年4月 2014年4月 2014年4月 2014年3月 2014年3月
2014年8月
2014年4月 2014年9月 2014年10月 2014年10月 2014年9月 2014年9月
★VARCO顶驱配件【nov华高】
National Oilwell Varco（中文译名：国民油井华高）NATIONAL OILWELL VARCO （中文译名：国民油井华高）作为井下工具和设备的世界领军企业，提供具有先进技术、精益制造和可靠质量的井下工具，并提供NOV 再认证及年度保养维修服务。
NOV在80多个国家分布着150 多个作业地点，NOV的全球性的网点分布、无和伦比的井下工具配套和经验丰富的人员配置，使我们能够满足顾客最苛刻的钻井工况需求。
NATIONAL OILWELL VARCO（中文译名：国民油井华高）是起升解决方案的最佳选择。
NOV 为海上工程船、固定及浮式采油的安装、海上支持设施和陆地使用提供专用工程设计、设备、系统及服务。
NOV 提供各种吊车、绞车、锚泊、铺管和敷缆系统、升降和滑移设备以及动态补偿系统。
此外，产品系列还包括FPSO 成套设备及锚泊牵引和供应船(AHTS) 成套设备。
National Oilwell Varco通过质量导向的生命周期管理以及售后备件和服务计划，提供无和伦比的起升解决方案。
钻井工具解决方案National Oilwell Varco提供世界上最全面和最可靠的钻井工具和设备。
我们为能成为唯一一家提供和服务全套井下钻具总成的独立井下工具制造厂商而自豪。
本公司的产品范围包括：钻头钻井马达动力部分扩孔器扩孔工具扶正器震击工具无磁钻井部件电磁随钻测量（MWD）系统钻铤钻井震击器钻井震击器助力器钻杆NOV 提供最广泛最全面的扩孔工具，以经验证的技术满足该行业最复杂、多样和困难的开孔作业要求。
我们的产品包括固定切削刃钻柱工具、双心钻头和同心井下扩孔器。
修井和完井解决方案National Oilwell Varco 制造的Bowen® 打捞工具已有85年以上的历史。
产品包括捕捞工具，打捞冲击工具（如：震击器、助力器、缓冲短节、碎物打捞工具），磨铣和切割工具以及修补工具。
NOV 提供计算机控制的“打捞和钻井震击器定位程序”，确定震击器在钻柱中的最佳位置以使震击的冲击力能量最大化，补偿井眼角度、井眼曲率和摩擦阻力的影响，适用于垂直、定向和水平井眼分析。
井下工具详细介绍
技术要求
1、下管柱时，管柱上提高度必 须小于防坐距（Y211），一般不得 超过0.4米，否则会使封隔器中途 坐封。如遇封隔器中途坐封时，可 上提管柱1米左右，解封后继续下 管柱。 2、在井下条件允许时，封隔器 下部应按30-40米尾管。 3、坐封封隔器的坐封高度，决 定于下入深度、坐封载荷和胶筒密 封压缩距等因素。
Bake公司生产的FH型静液压封隔器图
国内封隔器现状：
国内由于油藏类型多、工艺复杂，因此研制应用的分采 分注工艺管柱和配套工具在种类和工艺适应性方面强于国外， 基本满足生产需要。工艺及工具的整体设计水平与国外相近， 在某些领域甚至超越国外水平，但整体性能与国外相比仍有 较大差距，主要表现在原材料、加工工艺等方面，特别是井 下密封材料国内没有大的突破。 主要以Y211型封隔器、Y441型封隔器、Y341型封隔器、 K344封隔器、Z331封隔器为主。 耐温150℃， 耐压25MPa，工作寿命1.5年以上 。
自封式：Z331封隔器
压缩式：Y211、Y341、Y441封隔器
锲入式：锲入件锲入封隔件，使封隔件 直径增大，密封套管。
扩张式：一定压力的液体，作用于封隔 件内腔，扩大封隔件外径，密封套管。
封隔器型号编制
分类代号 支撑方式 坐封方式 解封方式 钢体最大外径
工作温度/压力
例：Y341-114-120/25
卡瓦式封隔器
一、用途 用于分层试油、采油、找水、 堵水、压裂、酸化和防砂。 二、结构如图所示。
Y221封隔器工作原理
坐封；按所需坐封高度上提管柱旋转管 柱。因扶正器依靠弹簧的张力造成扶正块 与套管壁的摩擦力沿轨迹中心管的轨迹槽 运动，滑环销钉从短槽的上死点运动到坐 封位置时的长槽的上死点，卡瓦从收拢状 态变成撑开状态（被锥体锥开），并卡牢 在套管壁上。同时坐封剪钉被剪断，上接 头、调节环和轨迹中心管下行，压缩胶筒， 使胶筒的直径变大，从而封隔油，套管环 形空间。 解封：上提管柱，上接头、调节环和轨 迹中心管一起上行。滑环销钉运动到下死 点，锥体退出卡瓦，卡瓦收回解卡；胶筒 收回解封。
NOV天津的井下工具工厂
NOV天津的井下工具工厂天津市临港经济区渤海26路1469号职位要求:Function:Tocentralize the expense report reviewing and implement common expense policy within whole China.费用报告审查，执行政策Rsponsibilities:Process new card applications and maintain the master information list处理新账户，维护职工清单，发票审查，报销，培训，审计，费用电子模块，问题处理，工作流，电子系统。
要求：英语好，税务，财会懂，熟悉AP软件。
Assist with efforts to expand and standardize T&E activityEnsure that policies at the company and business unit level are applied correctly d uring reviewingVerify all the invoices and receipts are bona fideSupport training initiatives for employees both online and in personAssist in the auditing of expense reportsCommunicate with employees any changes to the Expense moduleReview of Expense Administrator inbox for assigned location(s).- Address Expense user issues and questions, both functional and technical- Troubleshoot system issues a user or auditor may be experiencing, including revi ew of known issues, data gathering and appropriate hand-off to technical if requir edProvide Workflow Administrator service.- Monitor workflow on active Expense reports and provide support as needed Maintain or assist in maintaining within module:- Expense Report Templates, including Expense Type detail/requirements- Policy rules- Audit rules (special)- Flex field valuesRun ad-hoc reports for management and analysisOther requirements:Be familiar with accounting regulation especially in relation to tax invoiceBe good at English reading and writingBe familiar with the AP/AP processProfessional Experience : 2+ yearsMajor is accouting and relatives with a bachelor degree or above。
VARCO顶驱配件【nov华高】
National Oilwel l Varco（中文译名：国民油井华高）NATION AL OILWEL L VARCO（中文译名：国民油井华高）作为井下工具与设备的世界领军企业，提供具有先进技术、精益制造和可靠质量的井下工具，并提供NOV 再认证及年度保养维修服务。
NOV在80多个国家分布着150多个作业地点，N OV的全球性的网点分布、无与伦比的井下工具配套和经验丰富的人员配置，使我们能够满足顾客最苛刻的钻井工况需求。
NATION AL OILWEL L VARCO（中文译名：国民油井华高）是起升解决方案的最佳选择。
NOV 为海上工程船、固定及浮式采油的安装、海上支持设施和陆地应用提供专用工程设计、设备、系统及服务。
NOV 提供各种吊车、绞车、锚泊、铺管和敷缆系统、升降与滑移设备以及动态补偿系统。
此外，产品系列还包括FPSO 成套设备及锚泊牵引与供应船(AHTS) 成套设备。
Nation al Oilwell Varco通过质量导向的生命周期管理以及售后备件与服务计划，提供无与伦比的起升解决方案。
钻井工具解决方案Nation al Oilwel l Varco提供世界上最全面和最可靠的钻井工具与设备。
我们为能成为唯一一家提供和服务全套井下钻具总成的独立井下工具制造厂商而自豪。
本公司的产品范围包括：钻头钻井马达动力部分扩孔器扩孔工具扶正器震击工具无磁钻井部件电磁随钻测量（MWD）系统钻铤钻井震击器钻井震击器助力器钻杆NOV 提供最广泛最全面的扩孔工具，以经验证的技术满足该行业最复杂、多样与困难的开孔作业要求。
我们的产品包括固定切削刃钻柱工具、双心钻头和同心井下扩孔器。
修井与完井解决方案Nation al Oilwel l Varco制造的Bowen® 打捞工具已有85年以上的历史。
石油钻具产品英汉互译
词汇积累phoscoated磷化处理exceed超过Mechanical properties机械性能Drive section驱动部分die stamped冲压模具Identification标识steel barrel钢筒Across flats对边宽Eccentric偏心Lift plug提丝Lift cap提丝FJWP套铣管双级扣（梯形扣）TSWP套铣管双级扣（矩形扣）MPI磁粉检验LPI液体渗透检验Inspection检验Wells井STD standard 标准OAL overall length 全长Tong space 大钳空间Fishing neck length 打捞径长度钻井工具drilling tools四方钻杆square Kelly六方钻杆hexagonal Kelly钻杆drill pipe螺旋加重钻杆spiral heavy weight drillpipe加重钻杆heavy weight drill pipe螺旋钻铤spiral drill collar普通钻铤standard drill collar无磁钻铤non-magnetic drill collar无磁螺旋钻铤spiral non-magnetic drill pipe螺杆钻具downhole motor整体螺旋稳定器spiral integral blade stabilizer 整体直棱稳定器straight integral blade stabilizer 无磁稳定器non-magnet integral blade stabilizer 非旋转稳定器non-rotating stabilizer可换套稳定器replaceable sleeve stabilizer固定直径扩孔器fixed diameter hole opener滚轮铰孔器roller reamer套管刮削器casing scraper键槽扩大器key seat wiper旋塞阀Kelly valve全通径安全阀full opening safety valve投入式止回阀FT type drop-in check valve箭型止回阀FJ type-arrow back pressure valve内防喷器inside bop浮阀接头float valve sub旁通阀by-pass valve试压堵塞器cup tester定向接头oriented bent sub循环接头circulating sub转换接头straight sub变径转换接头reduce sub保护接头saver sub提升短节lift sub震击解卡工具jarring toolsQJZ型全机械式震击器mechanical drilling jar JYSZ型机械液压一体式震击器double acting mechanical-hydraulic drilling jarQYSZ型全液压式震击器double acting hydraulic drilling jarZSJ/ZXJ型机械液压两体式震击器hydraulic&mechanical two-piece drilling jarYSJ型液压上击器hydraulic up jarCSJ型超级震击器super fishing jarZJS型震击加速器jar intensifierDJ型地面震击器surface bumper jar KXJ型开式下击器fishing bumper subBXJ型闭开式下击器lubricated fishing bumper sub 钻柱减震器shock absorberSJ型双向减震器double-way shock absorberYJ型单向减震器one-way shock absorber打捞工具fishing toolsS-150可退式卡瓦打捞筒series150overshotS-70短鱼头打捞筒series70short catch overshotS-20短鱼头抽油杆打捞筒series20overshotS-10抽油杆打捞筒series10overshot可退式倒扣捞筒releasing and reversing overshot 提放可退式打捞筒lifting-lowering and releasing overshot可退式卡瓦打捞矛releasing spear倒扣捞矛reversing spear倒扣接头reversing sub滑块捞矛sliding block spear公锥taper tap母锥die collar内钩internal hook外钩external hook反循环打捞蓝reverse circulation junk basket强磁打捞器standard fishing magnet反循环强磁打捞器reverse circulation fishing magnet泥浆槽磁铁ditch magnet磨铣工具junk mills平底磨鞋flat bottom junk mill凹底磨鞋concave bottom junk mill裙式磨鞋skirted junk mill领眼磨鞋pilot mill铣锥tapered mill刀翼磨鞋bladed junk mill钻柱磨鞋string junk mill简易磨鞋economill机械式内割刀mechanical internal cutter机械式外割刀mechanical external cutter多层管柱割刀muti-string cutter段铣工具section millH型安全接头H safety jointAJ型安全接头AJ safety joint打捞杯junk sub铅印impression block钻穿越扩孔工具directional drilling traversing hole opener刀板式扩孔器cutting flat type hole opener飞旋切割刀fly-rotate cutter桶式扩孔器barrel type hole opener板桶联合式扩孔器flat-barrel combination type hole opener中心定位器center locator管圈式中心定位器tube ferrule type center locator 浮筒式中心定位器float barrel type center locator 转换接头（钻柱短节）crossover sub（drill string pup joint）喷浆短节（侧偏孔短节）guniting sub（side-hole sub）取芯工具coring tools维修设备service equipmentCZJ320W型完井液压拆装架completion hydraulic Bucking unitKCZJ400型翻盖式拆装架flip hydraulic bucking unit CZPT-II型液压拆装平台hydraulic makeup/breakout platformDYNJ-200/20型液压拧扣hydraulic screwing machine SYJ液压试验架hydraulic testerLMST-II型螺杆钻具马达试验台资料downhole drilling motor tester dataSXL自动上下料机SXLautomatic loading and unloading machine石油钻井工程英语词汇D D R R I I L L L L I I N N G GE E N N G G I I N N E E E E R R I I N N G G E E N N G G L L I I S S H H W W O O R R D D S S A A N N D D P P H H R R A A S S E E S S中油长城钻井有限责任公司钻机管理分公司Drilling Branch of GreatwallDrilling Company .Ltd，目录第一章：石油钻井工程英语基础词汇第1节石油钻井工程基础词汇 (1)第2节石油钻井方法基础词汇 (5)第3节石油钻井技术基础词汇 (5)第4节石油钻井参数基础词汇 (6)第5节石油钻井作业现场工作人员名称 (7)第6节石油作业现场常用工具 (8)第二章：石油工程常用设备及专业术语第1节钻井设备部分……………………………………………………1 3 第2节钻井泵类及相关设备……………………………………………1 6 第3节与泵操作有关的实用短语………………………………………18 第4节钻台与底座………………………………… (19)第5节井控操作与防喷器………………………………… (19)第三章：钻井工程作业部分第1节钻井事故………………………………… (24)第2节钻头………………………………… (25)第3节钻具………………………………… (25)第4节钻井工程地面作业实用词汇与短语 (27)第5节钻井工程井口作业实用词汇与短语 (28)第四章：钻井液及相关设备第1节钻井液名称………………………………… (30)第2节钻井液设备………………………………………………………3 1 第3节钻井液处理剂………………………………… (31)第五章：钻井相关作业第1节取芯部分………………………………… (35)第2节固井部分 (35)第3节固井水泥浆名称和参数 (37)第4节测井部分 (38)第六章：井下作业常用短语....................................39第七章：海上钻井作业 (40)第八章：定向井部分 (41)第九章：石油现场机械传动与机械设备第1节：动力与传动 (42)第2节机械加工与设备…………………………………………………4 4 第3节油品名称………………………………… (49)第十章：地质地层与油藏工程第1节地质及地层………………………………… (50)第2节油藏工程和采油工程……………………………………………5 1 第十一章：石油工程作业现场生活用词第1节身体各部分名称…………………………………………………5 2 第2节服装………………………………… (54)第3节描述天气………………………………… (56)第4节常见蔬菜名称………………………………… (57)第5节常见水果名称………………………………… (57)第6节味道和调味品调味品………………………………… (58)第7节酒类和祝酒………………………………… (59)第8节食1品 (59)第9节超级市场 (60)第10节容器、单位及钱币......................................................6 1 第11节肉类 (61)第12节海鲜，鱼类...............................................................6 2 第13节救火及救援...............................................................6 2 第14节日常生活用品............................................................6 2 第15节星期与月份...............................................................6 3 第16节数字 (64)第17节颜色 (65)第十二章：常用缩略语与换算第1节常用缩略语Abbreviation………………………………………6 6 第2节钻井现场常用公英制（美国用法）换算 (67)第一章：石油钻井工程英语基础词汇第1节石油钻井工程基础词汇钻井：drill定向斜井：directional drilling欠平衡钻井：under-balance drilling 海上钻井：off-shore drilling陆地钻井：on-shore drilling钻头：drill bit刮刀钻头：drag bit牙轮钻头：rock bit (镶齿钻头insert bit, 钢齿钻头steel toothed bit)金刚石钻头：diamond bit取心钻头：coring bit钻头浮阀：float valve钻头水眼：bit nozzle(or jet)钻头水眼刺:bit nozzle washed out钻头规：bit caliper(bit gauge)2钻头泥包：bit is balling钻头钝了，我建议现在起钻：bit is dull. I suggest to POOH now钻铤：DC(drill collar )光钻铤slick drill collar，螺旋钻铤spiral drill collar钻杆：DP(drill pipe ) 方钻杆：kelly公扣：pin end 母扣：box end内平式连接：IF(internal flash)正规式连接：REG(regular)贯眼式连接：FH(full hole)加重钻杆heavy weight drill pipe短钻杆 pop joint井下马达：downhole motor 涡轮钻具：turbine震击器：drilling jar减震器：absorber下部钻具组合：BHA（bottom hole assembly）钻具扶正器：stabilizer（string stabilizer, near-bit stabilizer）钻机：drill rig钻井泥浆：drilling mud 钻井液：drilling fluid钻井设备：drilling equipment油：oil 原油：crude oil天然气：nature gas煤层气：coal-bed gas石油：petroleum中国石油（简称）：CNPC（China National Petroleum Corporation ）长城钻井（简称）：GWDC(Great Wall Drilling Company)采油：oil production产油层(目的层)：reservoir( or pay zone)钻进：drilling调整钻井参数以得到理想的机械钻速：play the drilling parameters to get fast ROP起钻：POOH(pull out of hole)下钻：RIH(run in hole)下套管：run casing(or RIH with casing)短起下钻：wiper trip循环泥浆：circulate泥浆：reverse circulate中途循环泥浆：break circulation34分段下钻：RIH in stages 通井：control trip 划眼：reaming 倒划眼：back reaming 接单根：make connection滑、割大绳：slip and cut drilling line by ton-mile保养设备：maintain the equipment 修理设备: repair (or fix) the equipment保养顶驱：service TDS保养冲管：lubricate wash pipe 待工日费：standby rate今天零日费：there is no day rate today(zero day rate today) 我可以为您做，但必须收费，请理解 I can do for you and I have to charge(back charge) you. Please give me full understanding. 不在我的职责范围之内，我要汇报领导，一有消息会马上告诉你It is out of my power and I have to report to my boss. I will let you know as soon as I get news.大鼠洞：rat hole 小鼠洞：mouse hole钻具错扣：the connections are crossed钻具粘扣：thread is galled 丝扣坏了：the thread is damaged 起钻错扣：alternate the connections 新钻具或接头磨扣：break in the new tool joint新钻头磨合：break in the new bit PDC 钻头井底造型：shape the PDC bit 跳钻：rough drilling( vibrated drilling, bit is bouncing) 蹩钻：rough drilling （drilling torque is abnormally high ） 缩径：tight hole 起钻遇卡：get overpull 下钻遇阻：set weight部分漏失：partially lost circulation全部漏失：totally lost circulation 盲钻：blind drilling堵水眼：bit jets are blocked 掉水眼：bit jets are lost 憋压：the pressure is built up卸压：release pressure试压：pressure test功能测试：function test双方独自检查：double check地质：geology地质专业人员：geologist物理：physics地球物理勘探：geo-physical exploration.测井：logging电测井作业：wireline logging operation泥浆测井：mud logging井（副词“好”含意）：well拓展记忆：井眼：bore hole油气井：oil&gas well试井：well test井下：down-hole井下作业：down-hole operation第2节石油钻井方法基础词汇钻井原理：the principles of drilling 顿钻钻井：percussion drilling，cable-tool drilling旋转钻井：rotary drilling大位移井：big distance( or extended ) well侧钻井：sidetracking drilling水平井：horizontal well探井：wildcat，wildcat drilling深井：deep well浅井：shallow well老井：maturing well丛式钻井：cluster well drilling煤层气井：coal-bed gas well生产井：production well报废井：abandoned well停产井：none-production well井下情况：downhole condition第3节石油钻井技术基础词汇技术规范，技术指标，技术性能：specification拉伸：tension拉伸强度：tensile strength弯曲强度：bending srength最小屈服强度： minimum torsional strength应力：stress压力：pressure应力点：stress point压力降：pressure drop压力梯度：pressure gradient回压：back pressure大气压：atmosphere压差： pressure difference静液柱压力：static fluid cloumn pressure地层压力：formation pressure坍塌压力：collapse pressure破裂压力：fractured pressure液体：liquid固体：solid气体：gas，air正的：positive负的：negative水平的：horizontal垂直的：vertical第4节石油钻井参数基础词汇钻压：WOB（weight on bit）转盘转速：RPM（rotation per minute）泵压：SPP(slurry pump pressure)泵冲：SPM（stroke per minute）排量：FR(flow rate)大钩负荷：hook load扭矩：torque 反扭矩：reactive torque钻速：ROP(rate of penetration)顶驱：TDS(top drive system)钻井周期：drilling period钻井成本：drilling costs井眼尺寸：hole size垂深：TVD(total vertical depth) 井深：MD(measured depth)水平位移：horizontal displacement 井斜角：angle( or hole inclination)方位角：azimuth井眼环空：annulus第5节石油钻井作业现场工作人员名称甲方：oil company(operator)钻井承包商：drilling contractor第三方（分包商）the third party(sub-contractor)钻井经理：drilling manager监督：supervisor钻井监督：DSV(drilling supervisor) or Companyman地质监督：geologist泥浆工程师：mud engineer固井工程师：cementing engineer泥浆录井工：mud logger钻井队：drilling crew，drilling team 钻井1班：drilling shift one总经理：general manager总工程师：chief engineer项目经理：project manager(country manager)作业经理：operation manager财务经理：financial manger会计：accountant平台经理：rig manager 带班队长：tool pusherHSE监督：HSE officer司钻：driller副司钻：assistant driller井架工：derrick man钻工：roughneck（or floorman）场地工：roustabout泥浆工：mudman发动机工：motorman机械师： mechanic电工：electrician电焊工：welder司机：driver吊车司机：crane operator铲车司机：forklift operator营房经理：camp boss医生：doctor材料员：material man(storekeeper) 炊事员：cook翻译：interpreter洗衣工：laundry man厨房服务生：waiter保安：watchman(or security)机械工程师：mechanic engineer第6节石油作业现场常用工具扳手：wrench螺丝起子：screwdriver多角螺丝起子：Phlilips screwdriver （cross-headed screwdriver）撬杠：bar 加长撬杠：cheater bar活动板手：monkey wrench，adjustable wrench钳子：pliers钩子：hook台钳：bench vice钢挫：file榔头：hammer锤击扳手：hammer wrench搬手：spanner内六角扳手：Allen key钢锯：hacksaw砂纸：sandpaper管钳：pipe tongs(pipe wrench) 链钳：chain tong千斤顶：jack 黄油枪：grease gun吊车：crane 牵引绳：tag line电焊条：welding rod拖拉机：tractor推土机：bulldozer硬尺：ruler 游标卡尺：Vernier slide油漆：paint 铅油：dope油漆刷：paint brush 铅油刷：dope brush绝缘胶布：electrical tape 电线：wire插头：plug电插座：outlet(receptacle or switchboard)开关：switch螺栓：bolt螺帽：nut垫片：washer钉子：nail手电钻：hand drill钻头：bit工作台：workbench工具箱：toolbox胶水：glue胶棒：glue bar 护丝：thread protector 手轮：hand wheel 脚轰油门：throttle联接法兰：coupling flange(or adaptor flange)安全带：safety belt 安全帽：helmet工作靴：safety boot 工衣：coverall棉袄：coat 防护眼镜：safety goggle 手套：gloves 口罩：mouth mask围裙：apron 洗眼台：eye washing station 灭火机：fire extinguisher 消防栓：fire -hydrant 水龙头：water tap消防斧：fire fighting axe 铲子：shovel 手砂轮：emery wheel左转： turn left 右转： turn right 手势：gesture信号：signal 垃圾：waste garbage 拖把：mop 接头：sub配合接头：X-over ，cross-over 提升短节：lifting sub卡瓦：slips 放卡瓦：set slips 母锥：box tap 公锥：taper tap 打捞矛：fishing spear 安全接头：safety sub 柔性短节：flexible joint 井口盖子：wellhead cover 防喷盒：mud boxBOP 吊装：BOP trolley( BOP hoist) 吊卡：elevator 吊环：elevator links安全卡瓦：safety clamp(dog collar) 钻杆架：pipe rack 水龙头提环：swivel bail 材料房：warehouse绳卡：bullnose clamp(guy anchor) 绳套：sling 吊带：soft sling(belt)卸扣：shackle 吊装工具：lifting gear维护保养：maintenance内钳：make-up tong外钳：break-out tong液压大钳：power tong 液压猫头：E-zy tong兜绳：mule line四通阀：four-way valve 三通：Tee软管：hose球阀：ball valve闸板阀：gate valve 单流阀：back valve灌注泵：supercharge pump 第二章：石油工程常用设备及专业术语第1节钻井设备部分井架：Derrick(or mast)起（放）井架：erect(lay down) Derrick 底座大梁：sill 钢木基础：mat铅锤：plumb水平仪：level架，台：rack 立根盒：setback area坡道：V door(or ramp) 猫道：catwalk二层台：monkey-board 圆井盖：cellar cover天车：crown block 防碰天车：crown-o-matic天车梁：crown block beam 天车台：water table游动滑车：traveling block钻井大绳：drilling line 引绳：guide line穿大绳：string-in drilling line 金属线，电线：wire，cable钢丝绳股：strand截断：cutoff滑车，滑轮，皮带轮：pulley(hoist) 手拉葫芦：hand pulley吊耳：lifting eye顶驱：top drive大钩：hook大钩弹簧：hook spring大钩销子：hook pin大钩锁紧装置：hook locking device 大钩悬挂高度：hook height水龙头：swivel鹅颈管：gooseneck冲管：wash pipe水龙头盘根：swivel packing钻井水龙带: rotary hose( kelly hose)立管：stand pipe 立管管汇：stand pipe manifold高压管线：high pressure line 由壬：union低压管线：low pressure line 传感器：sensor放压管线：relief line转盘：Rotary Table转盘方瓦：master bushing方补心取出装置：bushing handling tool方补心：kelly drive bushing 方孔： square opening小鼠洞：mouse hole大鼠洞：rat hole绞车：Drawworks挂合（摘开）绞车：engage(disengage) drawworks液压绞车：hydraulic winch气动绞车：air tugger(air hoist)滚筒： drum( reel)滚筒高速气离合器：high speed clutch滚筒低速气离合器： low speed clutch锚头：cathead 液压猫头：E-zy tong 上扣猫头：make up cathead 卸扣猫头：make out cathead 牙嵌离合器：jaw clutch 涡磁刹车：eddy currentbrake(electromagnetic brake) 猫头轴：cathead shaft 猫头绳：cathead line 死绳：dead line死绳固定器：dead line anchor 间隙：gap死绳固定器膜片：dead line diaphragm 上扣：make up 上扭矩：torque sth 卸扣，卸开：break out 上紧，固定：tighten （fasten ） 松开，松扣：loosen 加载：load 卸载：unload盘式刹车：disc brake 刹车总成：brake assembly 刹车轴： brake shaft刹车带：brake band刹车片：brake block液压油箱：hydraulic power unit 液动试压泵 ：hydraulic test pump 液压大钳：hydraulic （power ）tong 倒档齿轮：reverse gear 动力扳手：power wrench吊钳钳头：hinged jaw 钳牙：die 大钳锁销：latch大钳悬臂：suspension bar 平衡重：counterbalance weight吊钳钳臂：tong arm 第2节 钻井泵类及相关设备泥浆泵：mud pump 活塞：piston 活塞杆：piston rod 活塞皮碗：piston cup 缸套：liner 凡尔体：valve body凡尔座：valve seat 凡尔箱：pump module 阀弹簧：valve spring 阀杆：valve lever阀面：valve face 阀帽：valve bonnet空气包：pulsation damper充氮气：refill with nitrogen 泥浆泵安全阀：pop-off valve 卸压管线：release line排出阀：discharge valve 吸入阀：suction valve 上水滤子：screen油尺：oil-level dipstick灌注泵：supercharge pump 冷却水泵：cooling pump潜水泵：submersible pump 盘根盒：stuffing box 叶轮：impeller单向阀：check valve （single-pass valve ）安全阀：safety valve 手动阀：manual valve 液动阀：hydraulic valve 拉杆：tie rod ，tension bar 压力表：pressure gauge 冲数：strokes 排量：flow rate80冲(次)/分：eighty strokes per minute泥浆罐：mud tank 倒泥浆：transfer mud循环罐：active tank储备罐：reserve tank 起下钻罐：trip tank溢流检查：flow check 沉砂罐：satteling tank 锥形罐：sand trap震动筛：sahle shaker 筛布：screen 目数：mash除砂器: desander 除泥器: desilter 离心机： centrifuge泥浆分配槽：spider box 缓冲罐buffer tank第3节 与泵操作有关的实用短语没有压力：No pressure压力过高：The pressure is too high 返回太少：Mud return is too few 水太少：Water is not adequate.抢修：Rush to repair 请看记录：Please check the record没作记录：No record available 加化学药品：add chemicals 测定比重：measuremudweight(specific gravity)测定失水：measure water loss 泥饼：mud cake测定切力：measure gel strength 停泵：stop pump请打手势：Please make a gesture 转动一周：turn round a circle 垫高一些：put something under it to raise抓紧：firmly grasp 抬高：lift it up 拿稳：hold firm 打一下： hit once 往外拉：pull outward 站稳：stand firm小端：small end 大端：large end光滑：smooth 粗糙：coarse ，rough 平面：flat 弯曲：bending放松：loosen 绷直：stretch tight ，draw tight 冷却：cooling 润滑：lubricate 过载：overload功率不足：power is not enough.第4节 钻台与底座钻台：drilling floor钻井班组记录：drilling tour record 司钻监视器：driller's monitor 司钻控制台：driller's console 指重表：weight indicator 底座：substructure 井队活动房：trailer 钻台上值班房：doghouse 梯子：ladder第5节 井控操作与防喷器溢流: kick溢流征兆: kick sign 气侵：gas cut 井喷： blow-out1次井控 the primary well control2次井控 the secondary wellcontrol3次井控 the tertiary well control 平衡 balance超平衡over-balance欠平衡under balance漏失试验leak-off test破裂压力fracture pressure额定压力 rated pressure工作压力 working pressure防喷器组BOP stack安装（甩下）防喷器组：nipple up(nipple down) BOP stack分流器diverter万能防喷器：annular preventer，bag preventer单闸板防喷器：single ram preventer 双闸板防喷器：double ram preventer （防喷器）闸板：pipe ram变芯闸板防喷器variable bore ram全封式防喷器：blind ram剪切防喷器：shear ram内防喷器 Inside BOP投入式单流阀DIBPV（Drop in blowout preventer valve）分流关线diverter line 节流管汇choke manifold节流阀choke valve旁通阀standby valve调压阀: Pressure regulator手动节流阀manual choke远程节流阀remote choke井口四通 drilling spool 变径法兰：adapter flange液压控制阀HCR(hydraulic controller)远程控制系统：koomey unit 蓄能器： accmulator压井管线：kill line入口：inlet 出口：outlet简易除气器：poor-boy degasser真空除气器：vaccum degasser泥浆池液面纪录仪Pit volume recorder(totallizer)泥浆流动传感仪mud flow sensor泥浆增量 Pit gains硫化氢侵入H2S influx加重材料Weighted material氮气Nitrogen乙炔：acetylene氧气：oxygen预冲氮气压力Pre-charge nitrogen pressure地脚螺栓连接Studded connection 法兰连接 Flange connection 箍盘连接 Hub connection演习：drill 急救演习：first aid drill消防演习：fire drill 防喷演习：kick drill 泄压: bleed off pressure带刻度压力表: calibrated pressure gauge带刻度容（体）积表: calibrated volume gauge 套管鞋: casing shoe 上部井眼段top hole section 快速钻进地层fast drillingformation压实地层：consolidated formation 风化地层：weathered formation 钻屑携带能力cuttings carrying capacity浅层气藏shallow gas地层破裂formation to break down压力梯度pressure gradient 地层压力formation pressure 井口压力wellhead pressure 漏失压力leak-off pressure 破裂压力fractured pressure 井底压力BHP( bottom hole pressure)正常压力normal pressure 异常压力abnormal pressure静液压力hydrostatic pressure 动态压力 dynamic pressure 环空压力annular pressure关井钻杆压力SIDPP (shut in drill pipe pressure)关井套管压力SICP( shut in casing pressure)最大关井套管压力maximum allowable surface pressure, MAASP最初循环压力 ICP( Initial circulating pressure)循环结束压力FCP(Final circulating pressure)U 形管原理U-tube principle 压井操作killing operation 补救措施remedial actions关井后循环circulation under wellclosed in condition cl 离子含量chloride contentDc 指数 Dc exponent软关井soft shut in硬关井hard shut in第1次循环first circulation第2次循环second circulation压井泥浆比重kill mud weight 抽吸swab激动surge含气地层gas bearing formation 含气页岩gas bearing shale 安全增量safety margin 记录卡片trip sheet低循环泵速SCR(slow circulation rate)当量泥浆密度EQD(equivalent mud density)当量循环密度ECD(equivalentcirculating density) 司钻压井法driller ’s method 等待压井法wait & weight method 体（容）积法volumetric method 下推压井法bull-heading method 不压井下钻：snub in第三章：钻井工程作业部分第1节 钻井事故井喷：blow out 井涌：kick井漏：lost circulation坍塌，井壁坍塌：cave in(collapse) 出砂：sand production砂桥：sand bridge 台阶：ledge键槽：keyseat 椭圆井眼：oval shaped hole 卡钻：sticking 填井：pack-hole 封井：packed drilling井下落物：fish大幅度活动钻具试图解卡：work the string and try to free it 活动钻具以避免卡钻：move(reciprocate ) the string to avoid being stuck.打捞：fishing 鱼头：top of fish 打捞工作：fishing job 侧钻：side-tracking 侧钻井眼：sidetracking hole 水泥窜槽：cement channeling 固井失败：cement failure 防砂：sand control缓慢开泵并仔细观察返浆情况： slowly start pumping and closely watch the return on the shale shaker第2节 钻头牙轮钻头：rock bit 刮刀钻头：drag bit 金钢石钻头：diamond bit镶齿钻头： insert bit 铣齿钻头：milled tooth bit喷射钻头：jet bit 牙轮：cone钻头装卸器：bit breaker 钻头直径：bit diameter 钻头寿命：bit life 钻头磨损：bit wear 钻头型号：bit type 水眼尺寸：nozzle size 水眼效率：nozzle efficiency 钻头接头：bit sub第3节 钻具方钻杆：kelly方钻杆旋扣器：kelly spinner 方钻杆旋塞：kelly cock 钻具：drilling string 钻杆：drill pipe 油管：tube钻具组合：drilling assembly 扶正器：stabilizer扩眼器：reamer （hole opener ） 钻铤：drill collar无磁钻铤：NMDC(non-magnetic drill collar)加重钻杆：HWDP(heavy weight drill pipe)近钻头扶正器：near-bit stabilizer 震击器：jar减震器：shock absorber 螺旋钻铤：spiral drill collar 键槽破坏器：key seat reamer 安全接头：safety joint 钻杆刮泥器：drill pipe wiper 泥浆动力钻具：mud motor 钻柱：drill string 涡轮：turbine涡轮钻具：turbo-drill stem 立根：stand 加厚：upset内加厚：IU(internal upset) 外加厚：EU(external upset) 内外加厚：internal-external upset 丝扣：thread打捞颈：fishing neck母扣：box 公扣：pin左旋螺纹：left-hand thread 右旋螺纹：right-hand thread 正规接头：regular joint 贯眼接头：full hole joint 内平接头：internal flush joint护丝：thread protector 快速护丝：easy protector 打捞工具：fishing tool 打捞作业：fishing operation 打捞篮：junk basket 卡瓦打捞筒：overshot 打捞杯：junk sub 牙轮打捞器：cone fisher 套管打捞矛：casing spear 打捞矛：fishing spear打捞公锥：male tap(fishing nipple) 打捞母锥：female tap(fishing socket)倒扣工具：reversing tool(backing-up tool)铣鞋：milling shoe 铣具：milling tool 平底铣鞋：flat bottom mill磁力打捞工具：magnetic fishing tool 打捞钩：fish hook气动工具：pneumatic tool 减摩短节：friction reduction sub 下套管漂浮接箍：casing floating coupling轴向加压器：hydraulic axialthruster 第4节 钻井工程地面作业实用词汇与短语方入：kelly-in 方余：kelly-up 开钻：spud in作业指令：instruction 钻井设计：drilling program井身结构：well schematic 岩性：lithology迟到时间：lag time(bottom up) 换钻头：change bit甩钻具：laydown drill pipe 发生故障：break down安装（拆卸）：rig up(rig down) 接头：sub adapter 机械手：mechanical arm 铁钻工：iron roughneck有故障：It fucked up( something is wrong with it)已修好：it has been fixed 马上去：Go there at once 请下去：Please go down请上来：Please come up躲开，危险：keep away ，danger. 请翻译来：Ask interpretor come here ， 冲洗：wash down 井口：well-head一根钻杆（单根）：single 三根钻杆组合（立根）：thribble 吊蓝：cage(basket) 换班： shift change第5节 钻井工程井口作业实用词汇与短语喇叭口：bell nipple出水管：mud return line(flow line) 试压杯：cup tester小心滑倒：wet floor, be careful 不要往井眼内掉东西：never fall down anything inside hole 我来做：Let me do it带把板手来：Bring a spanner ，please 带点密封剂：Bring a little sealant(Teflon)，please很快就好了：lt will be finshed rightaway抬一下：Let's lift it把绳子给我：Give me the rope ，please不漏：no leakage 电焊： welding气焊：gas welding气割：gas cut栏杆：handrail ，gangway rail ，railing 蒸汽：vapour压缩空气：pressurized (compressed) air注意安全：pay attention to safety 别动：Don't move ，Don't touch.对准：point out exactly.校正：align裸眼：open hole第四章：钻井液及相关设备第1节钻井液名称泥浆：mud钻井液：drilling fluid完井液：completion fluid修井液：work-over fluid压井液：killing fluid射孔液：perforating fluid 隔离液：spacer fluid 泥浆处理：mud treatment泥浆处理设备：mud treating equipment饱和盐水泥浆：saturated salt-water mud油基泥浆：oil-base mud 高粘度泥浆：heavy viscous mud重泥浆：weighted mud 重泥浆压钻杆：slug drill pipe起钻倒返泥浆：we have wet pipeduring POOH重晶石：barite纯碱：soda ash高岭土粉：koaline powder云母片： mica sheet增粘剂： viscosifier稀释剂： diluent (thinner)稳定剂：stabilizer (stabilizing agent)烧碱： caustic soda稀释dilution, thinning水泥凝固cement setting第2节钻井液设备离心泵：centrifugal pump振动筛跑泥浆：mud overflow shale shaker筛出：shake out混合泵：mixing pump混合漏斗：mixing hopper搅拌器：mud agitator泥浆抢：mud gun 岩屑：cuttings沉淀：settle沉积物：deposit吸入：suction吸入罐：suction pit泥浆天平：mud balance游码：slide weight支点：fulcrum刀口：edge调整，校正：adjust粘度计：viscometer第3节钻井液处理剂包，袋：sack粘土：clay膨润土，般土：bentonite钠：sodium钙：calcium氯：chloride氯化钙：calcium chloride石棉：asbestos分散：dispersal表面活性剂：surface-active material 铁络盐：lignite单宁：tannin羧甲基纤维素：carboxymethyl celluose CMC木纤维：xylogen石灰：lime二氧化钙：calcium oxide粉末：powder薄片：flake溶解：dissolve延迟，妨碍：retard处理剂，添加剂：additives缓凝剂：retarder支撑剂：proppant乳化剂：emulsifier润湿剂：wetting agent稳定剂：stabilizing agent除钙剂：calcium remover降失水剂：filtration-reducing agent PH值控制剂：PH control additive润滑剂：lubricant消泡剂：defoamer agent破乳剂：emulsion breaker洗涤剂：detergent防膨胀剂：anti-swelling agent粘土稳定剂：clay stable agent 稀释剂：thinner封堵剂：plugging agent抑制剂：inhibition agent暂堵剂：temporary plugging agent解堵剂：plugging removal堵漏剂：LCM (lost circulation material)水敏地层：water-sensitive formation 分散：dispersal水泥浆：cement slurry流变性：rheological characteristics 稳定性：stability稠化时间：thickening-time低密度水泥浆：low-density slurry 油气层保护：reservoir protection高渗透性：high-permeability砾石：gravity悬浮：suspension固化：solidification.防膨胀：anti-swelling高凝高粘度：high condensation and viscosity无毒的：non-poisonous无荧光：non-fluorescence钻井液性能参数 Specificaitons ofDrilling Fluid含水：water content密度：density厚度：thickness粘度：viscosity塑性粘度：plastic viscosity 含砂量：sand content屈服：yield屈服点：yield point屈服强度：yield strength剪切速率：shear rate剪切强度：shear strength剪切应力：shear stress稀释： dilute适用温度：safe temperature初始切力：initial gel strength 终切力：ten-min gel strength 触变性：thixotropy剪切稀释：shear thining液体浓度:concentration泥浆柱：mud column层流：laminar flow涡流：turbulent flow气泡：bubble 第五章：钻井相关作业第1节取芯部分岩心：core取心钻头：core bit取心筒：core barrel内岩心筒：inner barrel外岩心筒：outer barrel岩心爪：core catcher取心工具：corehandling tools取心收获率：core recovery rate取样器：sample blob取样盒：sample box样品筒：sample chamber取样工：sample catcher取样间隔：sample interval井壁取心：side-wall coring井壁取心枪：side-wall coring gun 取芯失败：coring failure第2节固井部分固井：cementing完井：well completion水泥：cement井口：wellhead井口压力：well head pressure井口回压：back pressure on the well head套压：casing pressure导管：conductor表层套管：surface casing技术套管：protective casing(intermediatecasing)油层套管：production casing尾管：liner尾管悬挂器：liner hanger通径轨：rabbit 封隔器：packer联顶节：landing joint套管柱casing string套管下部结构(含套管鞋、浮箍)：casing track(including casing shoe, float collar)套管扶正器：centralizer 止退环：stop collar口袋：pocket( rat hole)环空注水泥作业：top cement job碰压：bump plug 隔离液：spacer分级箍：stage collar水泥粘结强度strength of cement bond套管钳：casing tongs套管接箍：casing coupling套管头：casing head散装水泥：bulk-cement水泥浆：cement slurry插管注水泥：stab in cementing 插入密封接头：stab in adapter分级注水泥：stage cementing先行水泥浆：lead cement slurry末端水泥浆：tail cement slurry促凝剂：accelerator替浆：displace with mud水泥面：top of cement固井管线：chicksan line(cementing line)灰罐：silo(bulk tank)候凝：WOC(wait-on-cement)挤水泥：squeeze cement水泥塞：plug第3节固井水泥浆名称和参数超细水泥浆：ultrafine slurry普通水泥浆：normal slurry纤维水泥浆：fiber-reinforced cement slurry膨胀水泥浆：expanding cement slurry 低密度水泥浆：low-density slurry 水泥体积收缩：cement volume contraction水泥浆水化期间：cement slurry hydrating period水泥胶结质量：cement sheath bonding quantity失水率：the rate of water loss析水：liberate water稠化时间：thickening time凝固强度：cementation strength渗透性：permeability，膨胀率：expansion rate压缩强度：compression strength流动性：mobility第4节测井部分电测：wireline logging测井解释：logging interpretation 随钻测井：LWD(logging while drilling)测井电缆：logging cable测井工具：logging tool自然电位测井：spontaneous potential log感应电测井：induction electrical survey双感应测井：dual induction-laerolog 中感应测井：medium induction log 数字记录：digital record照相记录：photographic recording放射性测井：radioactivity log声波技术：acoustic wave technology 仪器耐温：the temperature resistance of the instrument仪器耐压：pressure resistance of instrument油气比：GOR (gas oil ratio)第六章：井下作业常用短语修井：work-over修井工具：work-over tool井下操作： down-hole operations. 产层污染： pollution of pay zone 增产措施：stimulations压裂和酸化：fracturing or acidizing 酸化处理：acid treatment人工压裂： artificial fracturing重复压裂过程： repetition presses for fracturing，压裂车： fracturing truck sets压裂后反映： post-fracture response 固体和液体添加泵： solid and liquid additive pump泵交联： pumping cross link交联剂： cross-linking agent排量： discharging三维压裂：three-dimension fracturing对压裂参数的监控、分析和解释：real time monitoring，analyzing and interpreting for fracturing operation parameters压裂操作：fracturing operation压裂规模：fracturing scale化学吞吐：chemical disposal乳化降粘：emulsification declining viscosity增注：augmented injection.。
NOV钻井绞车NOV Drilling Drawworks
Drilling DrawworksDC CHAIN DRIVEN DRAWWORKS1625-UDBE DC CHAIN DRIVEN DRAWWORKSDescriptionNOV’s conventional, chain-driven drawworks are proven, reliable machines that have set many standards in the drilling industry. The robust design and simplicity of these drawworks allow for east operation and maintenance.These drawworks are designed to provide maximum power in minimum space and feature DC electric motor drives.Total quality control and worldwide service are NOV’s assurance of optimum product performance in the field.Features/BenefitsPower – These Drawworks are normally powered with DC motors.Brakes – Disc brakes and band brakes are used as the primary braking system, and Baylor Eddy Current Brakes or Friction-Plate Brakes are used as auxiliary brakes.Controls – These drawworks can be controlled remotely or by a manual driller’s control console which is mounted on the skid1320-UDBE DC CHAIN DRIVEN DRAWWORKS110-UE/UDBE DC CHAIN DRIVEN DRAWWORKS80-UE DC CHAIN DRIVEN DRAWWORKS610-E DC CHAIN DRIVEN DRAWWORKSSpecificationsAC ELECTRIC GEAR DRIVEN DRAWWORKSADS-10SD AC ELECTRIC GEAR DRIVEN DRAWWORKSDescriptionNational Oilwell Varco's ADS Drawworks provide drillers with enhanced hoisting control capabilities that increase the efficiency, productivity and safety of the drilling process. The drawworks are equipped with AC motors which provide significantly more performance and have made possible a machine that requires approximately half the space and weight with less maintenance than traditional drawworks.BrakesA sophisticated braking system that offers precise proportional control to improve drilling and tripping technologyUnique AC-Power control characteristics allow regenerative braking and load holding without using the friction-plate brakesControlsAutomation of repetitive drilling operations through a wide variety of user-friendly NOV control systemsThe control system software includes the following features as standard:Monitoring and control of brake and lube systemMonitoring of AC motor temperature and cooling pressureInterface to hook load sensor (dead line)Dynamic Floor and Crown Saver SystemDisc Brake testing systemDisc Brake burning in system"Slip and Cut" functionDrawworks power management systemFeatures/BenefitsChoice of one, two, three or four AC motors with regenerative braking (see specifications chart)Unique modularity of common components offering configurable drawworks models for individual customer applications from 1500 to 6000 HPHigh capacity water and air-cooled friction-plate braking system offers precision control of the dynamic and static braking capabilitiesRobust single-speed gear drive reduces space and maintenance requirementsPowered by drilling-industry proven variable frequency drivesSingle unitized frame with simplified drum provides a significantly reduced moment of inertiaSpecificationsADS-10SD AC ELECTRIC GEAR DRIVEN DRAWWORKSADS-10T AC ELECTRIC GEAR DRIVEN DRAWWORKSSpecificationsSSGD-250 AC ELECTRIC GEAR DRIVEN DRAWWORKSDescriptionThe AC electric powered single speed gear driven SSGD-250 Drawworks offers a design unique to the industry. By overpowering a drawworks with AC motors, we are able to create a single shaft, single speed drawworks with hoisting performance comparable to a conventional drawworks. The result is a simple design with few mechanical parts, a small footprint and low weight. These drawworks require minimal maintenance, are entirelyself-contained and completely enclosed.Features/BenefitsElectric Motors:The Drawworks is equipped with 1 ea. GEB-22A1 (General Electric) alternating current (AC) motors. The motors are Exe motors with forced air-cooling. The motors have installed temperature sensors (PT100 elements) in the stator windings and for monitoring the main bearings. Encoders are mounted at the motor non-drive end for measuring the motor speed. The speed feedback from the encoder gives input to the frequency converters for optimal regulation of the AC-motor parameters.Motor Cooling Blowers:Blower skid assembly is provided for cooling of the Drawworks motors and ventilation of the enclosures. The skid consists of two blowers, back draft dampers, high efficiency weather louvers and an outlet plenum chamber.A damper is provided on the Drawworks roof between the plenum chamber and theAC-motors for isolation of the motors.Drawworks Control System:The Drawworks Control System consists of the following main parts:Drawworks Control cabinetMiscellaneous Field InstrumentationDrawworks Interface PanelEmergency stopSafety:The SSGD-500 Drawworks Control System is designed to provide enhanced safety and integrity for the operation, machinery, and the personnel on the rig. This is achieved by an active control philosophy with equipment self-checks and monitoring, and by use of duplicated critical equipment.The primary safety requirement for the SSGD-Drawworks is that 'one single point of failure shall not cause any hazardous condition leading to either personnel injury or any damage to the equipment'.The SSGD™ Drawworks is designed as a lifting device for drilling operations with fail-safe spring applied brakes.SpecificationsSSGD-360 AC ELECTRIC GEAR DRIVEN DRAWWORKSDescriptionNOV's Model SSGD-360 Drawworks is a single speed gear driven drawworks rated at 2300 hp and designed to accommodate two (2) AC drilling motors.Features/BenefitsPerformance:This drawworks is rated at 720,000 lbs (720 kips) maximum hook load on twelve (12), 1-3/8" drill lines, and 610,000 lbs (610 kips) maximum hook load on ten (10) lines.Drum:The drum is 56" in diameter and has Lebus grooving for 1-3/8" wireline. The drum is shaft mounted between spherical roller bearings that are bolted to the drawworks frame. The drum is direct driven through a single gear reduction of 10.5 to 1 ratio. Pinions are mounted directly to the motor shaft to reduce the overall size and weight of the gear set. The AC drilling motors are directly coupled to the main drum shaft, providing continuous operation without the use of transmissions or clutches.Service/Dynamic Braking:Normal service braking is performed by the AC motors by generating power into braking resistors. The motors and frequency drives are capable of holding full load at zero speed indefinitely. Load speed is limited by the control system to stay within the capacity of the motors.NOTE: The SSGD-360 drawworks requires full regenerative braking from the AC frequency drive system.Park/Emergency Brakes:The drawworks is equipped with a single 96.5" OD air cooled disc on the off-driller's side with three (3) NOV Model 132-455-14 self adjusting, fail safe, hydraulic operated calipers. Local brake controls on the drawworks allow the load to be manually lowered using the brake calipers. The brakes are normally spring applied and hydraulically released, in emergency situations they can also be hydraulically applied. An electronic interface to the drawworks controls is included to allow automatic brake activation for any fault whether failure or operator error.SSGD-500 AC ELECTRIC GEAR DRIVEN DRAWWORKSDescriptionThe AC electric powered single speed gear driven SSGD-500 Drawworks offers a design unique to the industry. By overpowering a drawworks with AC motors, we are able to create a single shaft, single speed drawworks with hoisting performance comparable to a conventional drawworks. The result is a simple design with few mechanical parts, a small footprint and low weight. These drawworks require minimal maintenance, are entirely self-contained and completely enclosed.Features/BenefitsElectric Motors:The Drawworks is equipped with 3 ea. GEB-22A1 (General Electric) alternating current (AC) motors. Continuous rating is 845 kW (1150 HP), 600 VAC, 1024 A at 800 rpm. The motors are Exe motors with forced air-cooling. The motors have installed temperature sensors (PT100 elements) in the stator windings and for monitoring the main bearings. Encoders are mounted at the motor non-drive end for measuring the motor speed. The speed feedback from the encoder gives input to the frequency converters for optimal regulation of the AC-motor parameters.Motor Cooling Blowers:Blower skid assembly is provided for cooling of the Drawworks motors and ventilation of the enclosures. The skid consists of two blowers, back draft dampers, high efficiency weather louvers and an outlet plenum chamber.A damper is provided on the Drawworks roof between the plenum chamber and the AC-motors for isolation of the motors.Drawworks Control System:The Drawworks Control System consists of the following main parts:Drawworks Control cabinetMiscellaneous Field InstrumentationDrawworks Interface PanelEmergency stopHoisting with 3 motors:The diagram below shows the hoisting capacity with all 3 motors available.Safety:The SSGD-500 Drawworks Control System is designed to provide enhanced safety and integrity for the operation, machinery, and the personnel on the rig. This is achieved by an active control philosophy with equipment self-checks and monitoring, and by use of duplicated critical equipment.The primary safety requirement for the SSGD-Drawworks is that 'one single point of failure shall not cause any hazardous condition leading to either personnel injury or any damage to the equipment'.The SSGD™ Drawworks is designed as a lifting device for drilling operations with fail-safe spring applied brakes.SSGD-750 AC ELECTRIC GEAR DRIVEN DRAWWORKSDescriptionThe AC electric powered single speed gear driven SSGD-750 Drawworks offers a design unique to the industry. By overpowering a drawworks with AC motors, we are able to create a single shaft, single speed drawworks with hoisting performance comparable to a conventional drawworks. The result is a simple design with few mechanical parts, a small footprint and low weight. These drawworks require minimal maintenance, are entirely self-contained and completely enclosed.Features/BenefitsElectric Motors:The SSGD 750 Drawworks is equipped with 4 ea. GEB-22A1 (General Electric) alternating current (AC) motors (other motors will be available on request). Continuous rating is 845 kW (1150 hp), 600 VAC, 1024 A at 800 rpm. The motors are Exe motors with forced air cooling. The motors have installed temperature sensors (PT100 elements) in the stator windings. Encoders are mounted at the motor non-drive end for measuring the motor speed. The speed feedback from the encoder gives input to the frequency converters for optimal regulation of the AC-motor parameters.Motor Cooling Blowers:One blower skid assembly is provided for cooling of the 4 motors and ventilation of the enclosure. The skid consists of two blowers, backdraft dampers, high efficiency weather louvers and an outlet plenum chamber. Two centrifugal blowers, one duty and one stand-by, are connected to a common duct leading to the drawworks enclosure. A plenum chamber on the roof of the enclosure splits the ducting into a separate duct for each of the GE-motors. A damper is provided between the plenum chamber and the GE-motors for isolation of the motors.Safety Philosophy:The Drawworks Control System, is designed to provide enhanced safety and integrity for the operation, machinery, and the personnel onboard the platform. This is achieved by an active control philosophywith equipment self checks and monitoring, and by extended use of redundancy for the Drilling Control Interface PLC to enable interlocks with other machines on the drill floor (anti-collision).The primary safety requirement for the SSGD-Drawworks is that 'one single point of failure shall not cause any hazardous condition leading to either personnel injury or any damage to the equipment'.The SSGD-Drawwork is designed as a lifting device for drilling operations with fail-safe spring applied brakes.Shut-down Logic:The Drawworks is designed for a fail safe operation where the safe condition is that the drawworks is parked with the brakes set, i.e. in case of a servere fault condition of the drawworks system, the drawworks control system will set the brakes and turn the drawworks off.The drawworks is equipped with many devices for monitoring of the drawworks and related equipment conditions. A failure on simple devices which does not influence the safety of the equipment or people on board will normally only give alarms on the Cyberbase screen. Other, more critical failures, will result in different actions from the control system depending on which operational mode is active, combined with continued warning to the driller as described below.Alarms leading to de-activation of a specific mode of the machine.Alarms leading to a de-activation of modes and shut-down of the machine in a normal manner.Alarms leading to activation of the Fail safe disk brakes.SSGD-1000 AC ELECTRIC GEAR DRIVEN DRAWWORKSDescriptionThe AC electric powered single speed gear driven SSGD-1000 Drawworks offers a design unique to theindustry. By overpowering a drawworks with AC motors, we are able to create a single shaft, single speed drawworks with hoisting performance comparable to a conventional drawworks. The result is a simple design with few mechanical parts, a small footprint and low weight. These drawworks requireminimal maintenance, are entirely self-contained and completely enclosed.Features/BenefitsElectric Motors:The SSGD-1000 Drawwork is equipped with 5 ea. GEB-22A1 (General Electric) alternating current (AC) motors. Continuous rating is 845 kW (1150 HP), 600 VAC, 1024 A at 800 rpm. The motors are Exe motors with forced air-cooling. The motors have installed temperature sensors (PT100 elements) in the stator windings and for monitoring the main bearings. Encoders are mounted at the motor non-drive end for measuring the motor speed. The speed feedback from the encoder gives input to the frequency converters for optimal regulation of the AC-motor parameters.Motor Cooling Blowers:Blower skid assembly is provided for cooling of the Drawworks motors and ventilation of the enclosures. The skid consists of two blowers, back draft dampers, high efficiency weather louvers and an outlet plenum chamber.A damper is provided on the Drawworks roof between the plenum chamber and the AC-motors for isolation of the motors.Drawworks Control System:The Drawworks Control System consists of the following main parts:Drawworks Control cabinetMiscellaneous Field InstrumentationDrawworks Interface PanelEmergency stopThe control system software includes the following features as standard:Monitoring and control of brake and lube systemMonitoring of GE motor temperature and cooling pressureInterface to hook load sensor (dead line)Dynamic Floor and Crown Saver SystemDisc Brake testing systemDisc Brake burning in systemCut & Slip functionDrawworks power management systemHoisting with 5 motors:The diagram below shows the hoisting capacity with all 6 motors available. An overload of 10% is required for hoisting 1000 short tons on yer. This can according to the motor vendor be done for several minutes provided that the motors are allowed adequate cooling time afterwards. No overload is required for lowering or holding the 1000 short tons (static hook load).Safety:The SSGD-1000 Drawworks Control System is designed to provide enhanced safety and integrity for the operation, machinery, and the personnel on the rig. This is achieved by an active control philosophy with equipment self-checks and monitoring, and by use of duplicated critical equipment.The primary safety requirement for the SSGD-Drawworks is that 'one single point of failure shall not cause any hazardous condition leading to either personnel injury or any damage to the equipment'.The SSGD™ Drawworks is designed as a lifting device for drilling operations with fail-safe spring applied brakes.SSGD-1000 AC ELECTRIC GEAR DRIVEN DRAWWORKSDescriptionThe AC electric powered single speed gear driven SSGD-1250 Drawworks offers a design unique to theindustry. By overpowering a drawworks with AC motors, we are able to create a single shaft, single speed drawworks with hoisting performance comparable to a conventional drawworks. The result is a simple design with few mechanical parts, a small footprint and low weight. These drawworks requireminimal maintenance, are entirely self-contained and completely enclosed.Features/BenefitsElectric Motors:The Drawworks is equipped with 6 ea. GEB-22A1 (General Electric) alternating current (AC) motors. The motors are Exe motors with forced air-cooling. The motors have installed temperature sensors (PT100 elements) in the stator windings and for monitoring the main bearings. Encoders are mounted at the motor non-drive end for measuring the motor speed. The speed feedback from the encoder gives input to the frequency converters for optimal regulation of the AC-motor parameters.Motor Cooling Blowers:Blower skid assembly is provided for cooling of the Drawworks motors and ventilation of the enclosures. The skid consists of two blowers, back draft dampers, high efficiency weather louvers and an outlet plenum chamber.A damper is provided on the Drawworks roof between the plenum chamber and the AC-motors for isolation of the motors.Drawworks Control System:The Drawworks Control System consists of the following main parts:Drawworks Control cabinetMiscellaneous Field InstrumentationDrawworks Interface PanelEmergency stopSafety:The SSGD-500 Drawworks Control System is designed to provide enhanced safety and integrity for the operation, machinery, and the personnel on the rig. This is achieved by an active control philosophy with equipment self-checks and monitoring, and by use of duplicated critical equipment.The primary safety requirement for the SSGD-Drawworks is that 'one single point of failure shall not cause any hazardous condition leading to either personnel injury or any damage to the equipment'.The SSGD™ Drawworks is designed as a lifting device for drilling operations with fail-safe spring applied brakes.SSGD-1250 AC Gear Driven DrawworksDSGD-250 AC ELECTRIC GEAR DRIVEN DRAWWORKSDescriptionNOV’s new Dual Speed Gear Driven (DSGD) Drawworks are setting new standards in the drilling industry. These AC drawworks features a two-speed helical gearbox mounted directly on the drum shaft which is ideal for any application where size and weight are critical factors. The two-speed functionality provides both extremely fast hoisting speeds and heavy hook load hoisting capabilities. The simple design of the DSGD Drawworks allows for easy operation and maintenance. Both transverse and longitudinal skid configurations are available to fit and substructure design.Features/BenefitsNo HPU requiredNo brake-water cooling system requiredRequires less horsepower input and fewer drives than single speed drawworks of the same maximum hook loadSmall footprint and light weight allows for easy moving between rig locationsAll DSGD models can be CE/Atex markedSpecificationsDSGD-375 AC ELECTRIC GEAR DRIVEN DRAWWORKSDescriptionNOV’s new Dual Speed Gear Driven (DSGD) Drawworks are setting new standards in the drillingindustry. These AC drawworks features a two-speed helical gearbox mounted directly on the drum shaft which is ideal for any application where size and weight are critical factors. The two-speed functionality provides both extremely fast hoisting speeds and heavy hook load hoisting capabilities. The simple design of the DSGD Drawworks allows for easy operation and maintenance. Both transverse andlongitudinal skid configurations are available to fit and substructure design.Features/BenefitsNo HPU requiredNo brake-water cooling system requiredRequires less horsepower input and fewer drives than single speed drawworks of the same maximum hook loadSmall footprint and light weight allows for easy moving between rig locationsAll DSGD models can be CE/Atex marked SpecificationsACTIVE HEAVE DRILLING DRAWWORKS (AHD)AHD-500 ACTIVE HEAVE DRILLING DRAWWORKSDescriptionWith development and introduction of the Active Heave Drilling™ (AHD) technology, National OilwellVarco offers a quantum leap solution to the drilling industry. AHD has already set new standards for compensation accuracy, improved wireline life, workable load range, and rig safety, by providing proven, active heave compensation for drill ships, semi-submersible drilling rigs, and floating drilling/production platforms. Costly, heavy, compensation systems and machinery are eliminated and the availablecapacity increases the operational window for the vessel, drastically reducing operating costs. Features/BenefitsAHD vs. Traditional Compensator Systems - Reduced Overall Equipment CostIncreased operational capacity and availability:Less waiting on weatherLess operational costLower weight and weight on drillfloor:Increased deckload capacityLess operational costLower center of gravity:Better vessel stabilityLess operational costMore accurate active heave compensation:Better drilling performance and easier equipment landingLess operational costLighter derrick and substructure:Less initial costEasy installation with few components:Less initial costReduced and easier maintenance:Less operational costRedundancy on critical components:High availabilityLess operational costSingle high speed:Faster tripping, riser and BOP runningLess operational costAHD-750 ACTIVE HEAVE DRILLING DRAWWORKSDescriptionWith development and introduction of the Active Heave Drilling™ (AHD) technology, National Oilwell offers a quantum leap solution to the drilling industry. AHD has already set new standards for compensation accuracy, improved wireline life, workable load range, and rig safety, by providing proven,active heave motion compensation for drill ships, semi-submersible drilling rigs, and floatingdrilling/production platforms. Costly, heavy, compensation systems and machinery are eliminated and the available capacity increases the operational window for the vessel, drastically reducing operatingcosts.Features/BenefitsAHD vs. Traditional Compensator Systems - Reduced Overall Equipment CostIncreased operational capacity and availability:Less waiting on weatherLess operational costLower weight and weight on drillfloor:Increased deckload capacityLess operational costLower center of gravity:Better vessel stabilityLess operational costMore accurate active heave compensation:Better drilling performance and easier equipment landingLess operational costLighter derrick and substructure:Less initial costEasy installation with few components:Less initial costReduced and easier maintenance:Less operational costRedundancy on critical components:High availabilityLess operational costSingle high speed:Faster tripping, riser and BOP runningLess operational costAHD-1000 ACTIVE HEAVE DRILLING DRAWWORKSDescriptionWith deve lopment and introduction of the Active Heave Drilling™ (AHD) technology, National OilwellVarco offers a quantum leap solution to the drilling industry. AHD has already set new standards for compensation accuracy, improved wireline life, workable load range, and rig safety, by providing proven, active heave motion compensation for drill ships, semi-submersible drilling rigs, and floatingdrilling/production platforms. Costly, heavy, compensation systems and machinery are eliminated and the available capacity increases the operational window for the vessel, drastically reducing operatingcosts.Features/BenefitsAHD vs. Traditional Compensator Systems - Reduced Overall Equipment CostIncreased operational capacity and availability:Less waiting on weatherLess operational costLower weight and weight on drillfloor:Increased deckload capacityLess operational costLower center of gravity:Better vessel stabilityLess operational costMore accurate active heave compensation:Better drilling performance and easier equipment landingLess operational costLighter derrick and substructure:Less initial costEasy installation with few components:Less initial costReduced and easier maintenance:Less operational costRedundancy on critical components:High availabilityLess operational costSingle high speed:Faster tripping, riser and BOP runningLess operational costSpecificationsAHD-1250 ACTIVE HEAVE DRILLING DRAWWORKS SpecificationsCM628TUT 1230 HP AC MOTORDescriptionNational Oilwell Varco offers a family of Baylor™ AC induction motors, designed specifically for continuous mud pump, rotary table, and drawworks oilfield drilling duty. In addition, there is also a family of Vertical AC induction motors, designed to provide increased electrical performance and superior mechanical durability in hex pump and top drive applications.High quality materials, robust construction, ISO 9001 manufacturing standards and technologically advanced electronic design software ensure reliable performance in the naturally hostile oil rig environment.Features/Benefits∙1230 hp continuous rating for mud pump and rotary table duty∙1450 hp intermittent rating for drawworks duty∙Constant 7700 lbs-ft torque from zero - 840 rpm∙Rated Load Slip - 3 rpm∙600-690 VAC, 1120 amps at 600 Volts∙Heavy duty insulated roller bearings∙Extreme duty shaft extension and bearings added for strength for side loads∙Six pole∙Rotor with heavy duty copper alloy cage bars and end rings∙Form wound stator coils∙VPI Class H insulated stator windings∙Stator RTDs, 100 ohm platinum, Bearing RTDs, 100 ohm platinum∙Differential Pressure sensor∙E(x)e 3200 cfm blower assembly (optional)∙ATEX / CE Certified∙VFD Continuous duty∙Motor enclosure protection - IP 45∙Terminal box protection - IP56∙Area classification: increased safety "e" T3 temperatureCM632UUT 1500 HP AC MOTORDescriptionNational Oilwell Varco offers a family of Baylor™ AC induction motors, designed specifically for continuous mud pump, rotary table, and drawworks oilfield drilling duty. In addition, there is also a family of Vertical AC induction motors, designed to provide increased electrical performance and superior mechanical durability in hex pump and top drive applications.High quality materials, robust construction, ISO 9001 manufacturing standards and technologically advanced electronic design software ensure reliable performance in the naturally hostile oil rig environment.Features/Benefits1500 hp continuous ratingConstant 9050 lbs-ft torque from zero - 880 rpm600VACRated load slip - 10 rpmHeavy duty insulated roller bearingsExtreme duty shaft extension and bearings added for strength for side loadsSix poleRotor with heavy duty copper alloy cage bars and end ringsForm wound stator coilsVPI Class H insulated stator windingsStator RTDs, 100 ohm platinum, bearing RTDs, 100 ohm platinumDifferential Pressure sensorE(x)e 4200 cfm blower assembly (optional)ATEX / CE CertifiedVFD Continuous dutyMotor enclosure protection - IP 45Terminal box protection - IP56Area classification: increased safety "e" T3 temperature。
井上井下工具介绍材料
中海油田服务股份有限公司
CHINA OILFIELD SERVICES LIMITED
反循环打捞篮和反循环强磁打捞篮 反循环打捞篮、反循环强磁打捞篮及其工作原理: 反循环打捞篮和组合式强磁打捞篮的钻井液循环路线相 同，下钻到底正循环冲洗井底之后，投入一钢球，待球 入座后，钻井液则由双层筒体之间的下水眼射到井底， 然后从井底通过铣鞋（或一把爪）进入捞筒内部，最后 由上水眼返回到环空间。在钻井液反循环作用冲击和携 带下，被铣鞋拨松的井底碎物随钻井液一起进入篮框， 或被磁芯吸住而捞获。
中海油田服务股份有限公司
CHINA OILFIELD SERVICES LIMITED
投入式回压阀
投入式回压阀是钻柱的 内防喷器，该工具带有1个 就位接头，连接在钻柱需要 的位置上，回压阀平时放在 钻台上，当需要时候及时投 入井眼，一次就能自动在就 位接头就位，切断向上喷射 的高压流，达到控制井喷的 目的。
中海油田服务股份有限公司
CHINA OILFIELD SERVICES LIMITED
随钻震击器震击负荷
震击器规格 最大上击力 最大下击力
8”震击器
6-1/2”震击器 4-3/4”震击器
180,000 lbs
100,000 lbs
140,000 lbs
80,000 lbs
110,000 lbs
60,000 lbs
中海油田服务股份有限公司
CHINA OILFIELD SERVICES LIMITED
卡瓦打捞筒
若是平口的叫R型、E型或M型密封平口控制环， 它不能修整鱼顶，若是铣齿的叫R型、E型、或M型密封 铣齿控制环，它可修整参差不齐和破损的鱼顶，若是打 捞油管接箍，则选用D型盘根。D型盘根由一个内密封件、 一个弹簧和一个外密封件（O型圈）构成。 •卡瓦打捞筒型号： •FS-full strength •SH-slim strength
各种井下工具中英文对照
测试投捞工具室Room of Casting and Fishing Tools in Logging1．打捞器：（打捞短钢丝与绳帽）本仪器适合打捞10米以下断钢丝。
Fishing tool: ( salvaging short steel wire and the rope headgear ) It is used for salvaging broken steel wires within the length of 10 meters.2．打捞器：专用打捞井底的外丝扣仪器，本仪器与加重杆配套使用。
Fishing tool: It is for the special use of salvaging outer buckles under well accompanying with aggravated poles.3．打捞器（打捞长钢丝）适合打捞10米以上钢丝必须与加重杆、钢丝绞车配合使用。
Fishing tool: It is fit for salvaging steel wires upwards of the length of 10 meters using aggravated poles and steel winches together.4．油管内壁取胶圈专用扳手，专用于取井底胶圈。
Special-purpose spanner of fetching rubber collar out of the inner wall of tubing, fetching rubber collar under well only.5．打捞器:（打捞内丝扣）专用打捞掉入井底的内线扣仪器，与加重杆配套使用。
Fishing tool: (salvaging inner buckle): for the special use of salvaging inner buckle under well using aggravated poles together.6．堵塞器：与水嘴配合使用，调节水量。
NOV 顶部驱动系列
NOV 顶部驱动系列1912 年，Varco 的前身Abegg & Reinhold，一家从事手动工具和钻机修理服务的公司，因为成功地将热处理件应用于油田生产而闻名于世。
改革创新的企业精神贯穿公司的发展历史，并最终成为石油行业领导者的必备品质。
如今，NOV 生产制造全系列的自动钻井设备，其中包括直流、交流顶部驱动钻井系统。
不论是打油井还是打气井，NOV 顶驱均被业界推为效率最高，安全性最强的产品。
无数次实践操证明，NOV 顶驱在提高钻井能力与效率的同时，可将作业时间缩短25%NOV 全系列交流和直流顶驱满足了用户不同的钻井要求。
海上钻井最初，NOV 顶部驱动系统用于海洋钻井，是因为海上恶劣的环境和苛刻的钻井条件需要一种结实可靠的钻井系统。
在其后相当长的时间里，随着井深的不断增加，侧钻技术的发明，以及高速钻头的发展，已经大大加强了顶部驱动系统在海上应用的优势。
伴随着石油天然气行业发展与挑战，NOV 不断确立直流和交流顶部驱动在海上钻井作业的性能和效率标准。
陆地钻井面对陆地钻井要求的变化，NOV 推出一系列便携式式交流电顶驱满足市场。
低维修成本，便携性，可靠性，低作业成本的设计理念贯穿每一种产品。
NOV 顶驱非常轻易，易于不同井架间的拆装和运输，不论是安装还是拆卸都能在几个小时之内完成。
交流变频技术提供了精确的速度和扭矩控制，以适应在不同作业条件下进行高效钻井。
一体化的液压系统，能够减少在环境污染和液体泄漏。
一体化的液压系统还省去了液压游动管线，同时节省了钻机作业过程中润滑油的消耗。
集体智慧的结晶从过去到现在，NOV 的技术人员，与客户一起不断创新顶部驱动的生产，效率及作业标准，以满足现代钻井行业的发展需要。
经验丰富的专家能够最大限度地满足用户的钻井作业要求。
依靠长年钻井经验，NOV 的技术人员能够准确掌握实际作业条件，为客户推荐出最适用的，性价比最优的顶部驱动系统。
完整的直流和交流顶驱产品系列，是NOV 满足最大限度满足客户钻井作业前提。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
国民油井华高（NOV ）井下工具（Downhole ）是世界最大的井下工具和设备独立供应商。
技术支持遍布80多个国家，具有150多家工厂和办事处，专门从事优化底部钻具组合（BHA ）和提高使用性能。
国民油井华高，具有一系列底部钻具组合解决方案和相关设备，主要包括以下方面：
钻头
国民油井华高公司Reedhycalog®钻头，拥有独特专利技术,并具有卓越的使用性能。
Reedhycalog®钻头根据不同地层，不同的驱动类型和井身结构而设计和提供不同的产品系列，能实现市场领先的机械钻速（ROP ），降低钻井成本。
钻井马达
国民油井华高公司井下工具全面提供各种井下马达，用于直井、定向井、小井眼和连续油管钻井。
在中国国民
油井华高可以提供各种性能钻井马达，根据客户需求，既可以销售，也可租赁。
∙ HEMIDRIL ®等壁厚马达
∙ PowerPLUS ™强动力马达
扩眼工具
国民油井华高公司扩眼工具部门，拥有业内最完整的扩眼工具种类和专业技术，能够满足最苛刻的扩眼挑战。
∙ A nderreamer™可变径扩眼器 ∙ 双心钻头及配套工具 ∙ 同心扩眼器及配套工具
钻井工具
国民油井华高井下工具部门提供石油天然气业内最可靠和最全面的钻井工具和产品，以满足当今钻井作业的要
求。
∙ Agitator ™水力振荡器 ∙ 水平井旋转导向工具
∙ Anderdrift ™直井测斜工具
∙
随钻震击器
/ Intensifier ™震击加速器
∙ 钻井缓冲器
打捞工具
国民油井华高井下工具部门生产的Bowen®打捞工具，是石油天然气工业界85年来最负盛名和值得信赖的打捞工具。
∙ 内外抓捞工具
∙ 落鱼振击工具 ∙ 落物回收打捞工具 ∙
磨銑和切割工具
修井和完井工具 国民油井华高井下部门，提供世界最广泛的所有工程作业
的连续油管工具，钢丝作业工具及流量控制设备。
∙
连续油管钻井工具 ∙ 连续油管震击器
∙ 连续油管清洗和打捞工具 ∙ 连续油管钢丝下放和上提工具 ∙ 连续油管切割器、刮刀、磁性捞砂筒
维修设备 国民油井华高井下工具部门制造的维修设备，为用户的井下工具及设备提供便捷维修服务。
∙ TorqueMaster ™ 上、卸扣器 ∙ 连续旋转 TorqueMaster ™机器
∙ 压曲机 ∙ 动力钳
∙ 震击器& 马达测试台
∙ 维修台钳
井下电子仪器
国民油井华高井下工具部门所制造的电磁无线随钻测量BlackStar 系统，建立了井下
数据采集标准，它与RSS 地面传感器相
结合，在最苛刻的环境下，提供全面的井下测量方案。
NOV Downhole is the largest independent downhole tool and equipment provider in the world. We have the expertise to optimize BHA selection and performance, supporting over 150 locations in more than 80 countries.
NOV Downhole’s complete range of solutions for the bottom hole assembly and related equipment includes:
Drill Bits
NOV ReedHycalog® drill bits feature unique patented technologies that deliver outstanding performance. Our product lines are designed for specific formations, drive types and well profiles to achieve market-leading Rate of Penetration (ROP), minimizing cost per foot.
Drilling Motors NOV Downhole
offers the most versatile array of
downhole motors available for straight hole, directional, slim hole and coiled tubing drilling. In China, NOV offers a variety of performance drilling motors for sale or rent, to meet customer needs.
∙ HEMIDRIL® ∙ PowerPLUS ™
Borehole Enlargement
NOV Downhole - Borehole enlargement has the most complete range of hole opening products in the industry, and the technical expertise to meet even the toughest of hole opening challenges.
∙ Anderreamer ™
∙ Bi-Centre drill bits & string tools ∙ Concentric near bit & string tools
Fishing Tools
NOV Downhole is the manufacturer of Bowen® Fishing Tools, the world’s most respected and reliable fishing tool products in the oil and gas industry for over 85 years. ∙ Catch tools
∙ Fishing stroking tools ∙ Junk retrieval tools
∙
Milling and cutting tools
Intervention and Coiled Tubing Tools
NOV Downhole offers the world’s most comprehensive
suite of Coiled Tubing Tools, Slick Line Tools, and Flow Control Equipment for all applications. ∙
CT Drilling Tools, ∙ CT Jars,
∙ CT Wash & Fishing tools.
∙ Wire line running and pulling tools
∙
Cutters, Scrapers, Magnets and Bailers.
Service Equipment
NOV Downhole manufactures equipment that enables users to conveniently service their downhole tools and equipment.
∙ TorqueMaster ™ Break Out Machines ∙ Continuous Rotation TorqueMaster ™ ∙ Bucking Units 弯管机 ∙ Power Tongs
∙ Jar & Motor Test Stands ∙
Service Vises
eTools
NOV Downhole manufactures BlackStar EM MWD system which sets the standard for downhole data acquisition. In combination with Russel Sub Surface sensors, NOV can provide complete downhole measurement options in even the most demanding environments.。