华为5100交换机配置步骤一(精)

5105也是下面这个用户名和密码，要注意的就是5105只有三块板子，board 0,board 1,board 2; board 0是上行板，也就是坏了的那块板子，其它两块是ADSL板，你先show board 0看一下上行以太口的状态是不是正常的，总之很简单，要是有什么问题就打我电话62002365)用户名：root密码：admin(在5100中键入命令，可以先键入头几个字母，然后用空格键显示其余字母，这个和路由器正好不同)enable (进入配置模式)MA5103#show (显示所有配置)Command word <alarm,board,cpu,efs,hdp,history,region-vlan,running-config,time,version,vlan>:b oard<frameId[/slotId]>{(0-4)[/(0-15)]}:0/1 (显示第一快板卡的信息，这里是adsl0/1板) Frame Slot Board Type Board State No.1 SubBoardtype No.2 SubBoardtype----- ----- ---------- -------------- ------------------ ------------------0 1 ADLE Normal - ------ ----- ---------- -------------- ------------------ ------------------ ActivatePort State VPI(PVC) Template---- ------------- ------------- ------------0 Activating No VPI 11 Activating No VPI 12 Activating No VPI 13 Activating No VPI 14 Activating No VPI 15 Activating No VPI 16 Activating No VPI 17 Activating No VPI 18 Activating No VPI 19 Activating No VPI 110 Activating No VPI 111 Activating No VPI 112 Activating No VPI 113 Activating No VPI 114 Activating No VPI 115 Activating No VPI 116 Activating No VPI 117 Activating No VPI 118 Activating No VPI 119 Activating No VPI 120 Activating No VPI 121 Activating No VPI 122 Activating No VPI 123 Activating No VPI 124 Activating No VPI 125 Activating No VPI 126 Activating No VPI 127 Activating No VPI 128 Activating No VPI 129 Activating No VPI 130 Activating No VPI 131 Activating No VPI 1---- ------------- ------------- ------------MA5103＃c onfigure terminal (进入配置模式)MA5103(config)#atmlan (配置atm或者eth)Command word <firewall,ip-access,ip-address,ip-refuse,ip-route,mtu>:ip-address (配置ip地址){ethernet,atm}:atm (这里配置atm的ip)<IP address>:10.100.0.87 (网管ip，是作带内管理用atm)<mask>:255.255.255.0Changing system IP may effect existent connection,Are you sure?(y/n) [n]:ySet successfully.A5103(config)#atmlan ip－access(配置允许访问系统的ip地址范围这里是用户的地址断，数据由局方提供，下面还有配置网管地址断可以访问)<start IP address>:10.4.84.0<end IP address>:10.4.84.254<mask>:255.255.255.0Add acceptable IP address successfully.MA5103(config)#atmlan (建立允许各个5100之间网管可以互访)Command word <firewall,ip-access,ip-address,ip-refuse,ip-route,mtu>:ip-access<start IP address>:10.100.0.1<end IP address>:10.100.0.254<mask>:255.255.255.0Add acceptable IP address successfully.MA5103(config)#atmlan (允许网管地址访问该设备)Command word <firewall,ip-access,ip-address,ip-refuse,ip-route,mtu>:ip-access<start IP address>:10.200.0.1<end IP address>:10.200.0.254<mask>:255.255.255.0Add acceptable IP address successfully.MA5103(config)#atmlanCommand word <firewall,ip-access,ip-address,ip-refuse,ip-route,mtu>:ip-route <subnet address>:0.0.0.0 （建立网管地址的默认路由）<mask>:0.0.0.0<gateway>:10.100.0.1 （本机管理地址的网关）Add successfully.MA5103(config)#interface (进入一个板卡进行配置这里进入lan板)Command word <adsl,aiu,ces,fr,imu,lan,mmx,vdsl>:lan<frameId/slotId>{(0)/(0-6)or(9-15)}:0/6 (lan板在0/6上)-----------------------------------------------Mode [System Mode] (lan板的操作命令)-----------------------------------------------cls Clear screen[no]exec-timeout Permit/Forbid to timeout and logouthelp Description of the interactive help system[no]help-mode Enable/Disable help mode operation[no]monitor Open/Close the switch of debug information outputping Send echo messages to test networks reachable[no]scroll Screen scroll manually/automaticallysearch Search command content the word user inputshow[11] <Group> Commands of show system information[no]smart Enable/Disable interactive operationterminal[1] <Group> Set terminal attributetracert Trace route to destination-----------------------------------------------Mode [Config LAN]-----------------------------------------------[no]bind[2] <Group> Commands of bind system informationclear[1] <Group> Commands of clear operationSet default VLAN of LAN board portend Exit to Privileged EXEC modeexit Exit current command modeinterface[8] <Group> Commands of interface configuration mode[no]loopback Set/Cancel LAND local loopbackmax-mac-count Set the max learnable MAC addresses of PVC[no]mirror Set/Cancel a port mapping to another port of LANDoperation-mode Switch LAN board operation mode[no]pitp[2] <Group> Commands of pitp system informationport[2] <Group> Commands of port informationshow[15] <Group> Commands of show system information[no]shutdown Close/Open ethernet port of LAN boardtraffic-suppress Set the traffic suppression[no]trunk Add/Delete a trunk of LAN boardtrunk-mode Set trunk mode of LAN boardvlan[3] <Group> Commands of vlan managementvport Set vport - opposite physical portIDMA5103(config-LAN-0/6)#operation-mode (选择lan操作模式){general,ipdslam,ipcascade}:ipdslam (选择ipdslam模式，该模式各端口不能进行配置) Please delete all LAN access PVC(except LAN-NMS PVC)of current board before(修改模式以后，系统会自动重启lan板)switching operation mode.Do you want to reserve LAN-NMS PVC of current board?(y/n) [y]:ySome configuration data may be lost,are you sure to switch operation mode and to reset current board?(y/n) [n]:yReset command was sent to service board successfully.Switch operation mode successfully.2004/09/15 14:29:23 minor MMX: Board manual reset(0/6)MMA5103(config)#MA5103(config)#interface (进入lan板进行vlan配置)Command word <adsl,aiu,ces,fr,imu,lan,mmx,vdsl>:lan<frameId/slotId>{(0)/(0-6)or(9-15)}:0/6MA5103(config-LAN-0/6)#vlanCommand word <add,delete,mask>:add (增加一个小区vlan，用于用户的访问，所有的用户共用一个小区vlan){general,region}:region<vlanId>{1-4095}:121 (该数据由局方提供)<vpi>{0-127}:0<vci>{32-127}:35Failure: Board is configurating.(ipdslam模式下只支持regiong vlan 小区vlan，不支持general vlan ，虽然有这个提示铁通的网管vlan为100 ，是一个general vlan，在建立网管的时候直接建立，后面有方法)MA5103(config-LAN-0/6)#vlanCommand word <add,delete,mask>:add{general,region}:general<vlanId>{1-4095}:100<vlanMask>{0x1-0xff}:0xffFailure: Current operation mode is IPDSLAM mode.(这里提示ipdslam模式下不支持general vlan)MA5103(config-LAN-0/6)#exitMA5103(config)#exitMA5103#save (不要忘记再做了配置以后将配置存盘)Are you sure to save system data?(y/n) [y]:yThis operation will take several minutes, please wait...Frame 0 Slot 7 saving data in progress 2%.Frame 0 Slot 7 saving data in progress 2%.Frame 0 Slot 7 saving data in progress 2%.Frame 0 Slot 7 saving data in progress 2%.Frame 0 Slot 7 saving data in progress 20%.Frame 0 Slot 7 saving data in progress 22%.Frame 0 Slot 7 saving data in progress 24%.Frame 0 Slot 7 saving data in progress 26%.Frame 0 Slot 7 saving data in progress 28%.Frame 0 Slot 7 saving data in progress 29%.Frame 0 Slot 7 saving data in progress 31%.Frame 0 Slot 7 saving data in progress 33%.Frame 0 Slot 7 saving data in progress 35%.Frame 0 Slot 7 saving data in progress 37%.Frame 0 Slot 7 saving data in progress 39%.Frame 0 Slot 7 saving data in progress 40%.Frame 0 Slot 7 saving data in progress 100%.Save data to FLASH successfully.MA5103＃c onfigure terminalMA5103(config)#adsl (增加adsl模板，这里只有上下行速率需要设置) Command word <template>:templateCommand word <add,delete,modify>:add (增加模板2 默认模板为1，不要删除) [<index>]{2-99}:2During input,press 'Q' to quit,then settings at this time are neglected. > Will you set basic configuration for modem? (y/n) [n]:y> ADSL operating mode:> 0: All(G992.1, G992.2, T1.413)> 1: Full rate(G992.1 or T1.413)> 2: G992.2(g.lite) (ADLI can not support )> 3: T1.413 (ADLI can not support )> 4: G992.1(g.dmt)> 5: g.hs(Allows 992.1 and 992.2 with priority to 992.1)Please select (0~5) [0]:> Trellis coding 0-disable 1-enable (0~1) [1]:> Upstream channel bit swap 0-disable 1-enable (0~1) [0]:> Downstream channel bit swap 0-disable 1-enable (0~1) [0]:> EOC mode 0-transparent mode 1-HDLC framing mode (0~1) [1]:> Please select channel mode 0-interleaved 1-fast (0~1) [0]:> Set interleaved delay mode 0-manual 1-auto(0~1) [0]:> Unit of interleaved delay 0-DMT 1-ms (0~1) [0]:> Will you set interleave depth? (y/n) [n]: y (设置通道工作方式）> Max downstream interleaved depth 2,4,8,16,32,64,128 DMT (2~128) [32]:> Max upstream interleaved depth 2,4,8,16,32,64,128 DMT (2~128) [16]:> Will you set noise margin for modem? (y/n) [n]:> Will you set parameters for rate? (y/n) [n]: y (是否配置上下行速率这里注意选Y）If you want the fixed rate, set the Min value equal to Max value.> Min bit rate in downstream (32~32000 Kbps) [32]: 32> Max bit rate in downstream (32~32000 Kbps) [6144]: 1024> Min bit rate in upstream (32~2208 Kbps) [32]: 32> Max bit rate in upstream (32~2208 Kbps) [640]:512Add template 2 successfullyMA5103(config)#interface adsl<frameId/slotId>{(0-4)/(0-6)or(9-15)}:0/1 (进入第一快adsl板)MA5103(config-ADSL-0/1)#deactivate all (先去激活所有端口，以后再用模板2激活端口) Port 0: Command send successfully.Port 1: Command send successfully.Port 2: Command send successfully.Port 3: Command send successfully.MA5103(config-ADSL-0/1)#activate all 2 (用模板2再次激活各个端口)Port 0: Command send successfully.Port 1: Command send successfully.Port 2: Command send successfully.Port31: Command send successfully.MA5103(config-ADSL-0/1)#interface adsl 0/2 (进入adsl板0/2)MA5103(config-ADSL-0/2)#deactivate allPort 0: Command send successfully.Port 1: Command send successfully.Port 2: Command send successfully.Port 3: Command send successfully.Port 4: Command send successfully.MA5103(config-ADSL-0/2)#activate all 2Port 0: Command send successfully.Port 1: Command send successfully.Port 2: Command send successfully.Port 3: Command send successfully.Port 4: Command send successfully.Port 5: Command send successfully.Port31: Command send successfully.MA5103(config)#show (show board 0/6 显示lan板信息）Command word <alarm,board,cpu,efs,hdp,history,region-vlan,running-config,time,version,vlan>:b oard<frameId[/slotId]>{(0-4)[/(0-15)]}:0/6Frame Slot Board Type Board State No.1 SubBoardtype No.2 SubBoardtype----- ----- ---------- -------------- ------------------ ------------------0 6 LAND Normal H511E8FS ------ ----- ---------- -------------- ------------------ ------------------Auto Default Pause Partner SelfPort Tagged Nego Speed Duplex VLAN ID Frame State Active Auto Nego Apt---- ------ ------ ----- ------ ------- ------- ------- ------ --------- ----0 - Yes 100M Full - Yes OnLine Yes Yes Off1 - Yes - - - - OffLine Yes - Off2 - Yes - - - - OffLine Yes - Off3 - Yes - - - - OffLine Yes - Off4 - Yes - - - - OffLine Yes - Off5 - Yes - - - - OffLine Yes - Off6 - Yes - - - - OffLine Yes - Off7 - Yes - - - - OffLine Yes - Off---- ------ ------ ----- ------ ------- ------- ------- ------ --------- ---- Trunk mask : No trunk maskOperation mode: IPDSLAMMA5103(config)# show vlan (显示所有vlan)<frameId/slotId>{(0)/(0-6)or(9-15)}:0/6 (显示lan板上的vlan)[<vlanId>]{1-4095}:121This operation will take several minutes,please wait...VLAN ID Mask VLAN Index Attribute------- --------------- ---------- ----------121 - 0 RegionMA5103(config)#multi-pvc (建立adsl端口到lan板的pvc){adsl,lan}:adsl<FrameId/SlotId>{(0-4)/(0-6)or(9-15)}:0/1<portId-mask>{0x1-0xffffffff}:0xffffffff (将建立所有端口的pvc){region,vpi}:region{adsl,lan}:lan<FrameId/SlotId>{(0)/(0-6)or(9-15)}:0/6 {vlanId,anyvlanId}:vlanid (选择vlan)<vlanID>{1-4095}:121<car>{both,up,down,off}[off]:off<priority>{0-7}{off}[off]:off<rx-cttr>{1-512}:1<tx-cttr>{1-512}:1Add PVC successfully, CID = 1.Add PVC successfully, CID = 31.Add PVC successfully, CID = 32. Success to add 32 PVC.Fail to add 0 PVC.。