金鼎三辊闸使用说明书

安全警告
1）本产品是技术性较强之设备，使用时系统若发生故障，应及时通知我公司客服部门或指定的经销代理机构。

2）售后服务部门或授权服务机构进行处理，切不可随意拆卸，以免损坏内部结构或操作不当而损害您的权益。

3）本产品在使用时，严禁坐、压或用力晃动、闸杆机构，以免造成闸机不必要的损坏。

4）本产品在使用时带有危险电压，安装时须可靠接地并应定期检察系统保护地，以免造成不必要的人身伤害及设备损坏。

5）请参照说明正确使用本设备的接口电特性，以免损坏本设备和用户的其它设备。

6）本设备无防爆设计，请勿使用本设备于含有易燃易爆环境。

如需要请选购本公司其它型号的产品。

1）The product is provided with powerful technology, and therefore you should promptly notify the customer service department or the designated distribution agency of our
company if the system fails when it is used.
2）The user or manager shall inform our company’s after-service department or authorized organizations to dispose the problem, never detach the product willingly for to avoid further damage.
3）When using the equipment, sitting or pressing railing barrier rod by force is strictly prohibited so that avoids unnecessary damage of railing barrier.
注意：地埋PVC线管深度应大于60mm，露出地面高度应大于50mm，且出口回弯，以防止线管进水。

Precautions:
The buried PVC tube should be with a depth greater than 60mm, the exposed section should be 50mm higher than the earth and the exit mouth should be bending back to avoid dipping of water into the tube.
5)As shown in the connecting diagram of the system, connect the power line, control line
to the connecting socket of the main controller board of the turnstile, and connect
Precautions:
1）All the operation above should be carried out under power off condition, and it should be ensured that the protection ground wire of the system is connected correctly, properly and firmly.
2）In case the equipment selected is used outdoor, a concrete installation platform of a size of 100mm~200mm should be prepared for humidity-proof at the location for installation of the equipment.
4.2 Equipment Status Checking
1）Check carefully the system connection in accordance with the connecting diagram of the system, and the power on when it is confirmed that everything is normal.
2）Checking the barrier rod zero position:
The barrier rod should be at the zero horizontal position when the rod up action is stopped, otherwise, the zero position switch should be adjusted. The method is as follows: l Open the upper cover of the machine case with key and use screwdrivers to remove the upper cover of the main controller.
l Short-connect J1, press s2 button and select the menu 13, the press S13 button to enter the zero adjustment, hold any one barrier rod and rotate it, adjust in at the zero position and then disconnect J1.
l Cover the upper cover of the main controller and tighten it.
4.3 System Settings
All parameters of the system are set on the main control board and the setting steps are as follows:
1)Open the upper cover of the machine case with key and use screwdrivers to remove the
upper cover of the main controller.
2)Short-connect J1 jumper wire.
3)Press s2 button and at the same time observe the display of the two front digits of LED,
the value of numerical code is added by 1 by each time press, and select the
Precautions:
1）Please do not use the system when there is lightning, otherwise the turnstile may be damaged.
2）It is required reliable connections of the protection grounding wires of the system to avoid any accident.
5.2 Regular Maintenance
1）The housing of the equipment is of a sub-polish stainless steel. It is required to clean regularly with soft cloth or cleanser especially for stainless steel so as to keep a clean
and polishing surface. It is forbidden to clean the surface with a hard object; otherwise,
the good looking appearance may be affected. It is also forbidden to wash it with water,
otherwise, short circuit may occur in the electric control system and the equipment may
be damaged.
2）It is required to check regularly the connection of various movement sections of the equipment. Fasten timely the loose fasteners such as nut and screw; otherwise, turnstile
failure may be resulted due to long term working.
3）It is required to check regularly the protection grounding wires of the system to ensure
a reliable connection.
4）It is required to check regularly the connectors and line connection points to ensure a。