HES06B-S033120中文资料

合集下载

ABS塑料性能和部分牌号介绍

ABS塑料性能和部分牌号介绍ABS塑料- ABS树脂是五大合成树脂之一,其抗冲击性、耐热性、耐低温性、耐化学药品性及电气性能优良,还具有易加工、制品尺寸稳定、表面光泽性好等特点,容易涂装、着色,还可以进行表面喷镀金属、电镀、焊接、热压和粘接等二次加工,广泛应用于机械、汽车、电子电器、仪器仪表、纺织和建筑等工业领域,是一种用途极广的热塑性工程塑料。

ABS树脂是目前产量最大,应用最广泛的聚合物,它将PS,SAN,BS的各种性能有机地统一起来,兼具韧、硬、刚相均衡的优良力学性能。

ABS是丙烯腈、丁二烯和苯乙烯的三元共聚物,A代表丙烯腈,B代表丁二烯,S代表苯乙烯。

ABS塑料-名称化学名称丙烯腈-丁二烯-苯乙烯塑料英文名称 Acrylonitrile Butadiene Styrene plasticABS塑料-性能一般性能ABS外观为不透明呈象牙色粒料,其制品可着成五颜六色,并具有高光泽度。

ABS相对密度为1.05左右,吸水率低。

ABS同其他材料的结合性好,易于表面印刷、涂层和镀层处理。

ABS的氧指数为18~20,属易燃聚合物,火焰呈黄色,有黑烟,并发出特殊的臭味。

力学性能ABS有优良的力学性能,其冲击强度极好,可以在极低的温度下使用;ABS 的耐磨性优良,尺寸稳定性好,又具有耐油性,可用于中等载荷和转速下的轴承。

ABS的耐蠕变性比PSF及PC大,但比PA及POM小。

ABS的弯曲强度和压缩强度属塑料中较差的。

ABS的力学性能受温度的影响较大。

热学性能ABS的热变形温度为93~118℃,制品经退火处理后还可提高10℃左右。

ABS 在-40℃时仍能表现出一定的韧性,可在-40~100℃的温度范围内使用。

电学性能ABS的电绝缘性较好,并且几乎不受温度、湿度和频率的影响,可在大多数1环境下使用。

环境性能ABS不受水、无机盐、碱及多种酸的影响,但可溶于酮类、醛类及氯代烃中,受冰乙酸、植物油等侵蚀会产生应力开裂。

HEDS-9140中文资料

Applications
The HEDS-9040 and 9140 provide sophisticated motion control detection at a low cost, making them ideal for high volume applications. Typical applications include printers, plotters, tape drives, and industrial and factory automation equipment.
2.16 (0.085) DEEP
1.78 ± (0.070 ± 0.004)
2.92 ± 0.10 (0.115 ± 0.004)
OPTICAL CENTER
10.16 (0.400)
OPTICAL CENTER LINE
5.46 ± 0.10 (0.215 ± 0.004)
TYPICAL DIMENSIONS IN MILLIMETERS AND (INCHES)
元器件交易网
Three Channel Optical Incremental Encoder Modules
Technical Data
HEDS-9040 HEDS-9140
Features
• Two Channel Quadrature Output with Index Pulse
1.52 (0.060)
DATE CODE
3.73 ± 0.05 (0.147 ± 0.002)
20.8 (0.82)
11.7 (0.46)
2.21 (0.087) 2.54
(0.100)
2.67 (0.105) DIA. MOUNTING THRU HOLE 2 PLACES

HESB045-00

乙烯管HES B 045-00 （版本号：1）1 适用范围本标准适用于标准部件用的乙烯管（下称管子）。

备注1）燃料管必须用HES B 044中的（燃料软管·夹层管）。

备注2）本标准中所用单位及数值为SI单位制，{ }中的单位及数值是以前单位的标准值。

2 种类管的种类见表1。

注（*1）制品的标记方法按照5项（标记方法及部件号码）的规定，但也可根据需要采用记号。

注（*2）带（有）编织物是如图1所示那样的中间夹有编织物。

说明：带（有）织物管子通常叫作夹层管。

注（*3）若是VT-BH、VT-BH2及VT-BH3，取管长时，必须考虑汽油或乙醇对管子的收缩影响，需按设计尺寸加长5%。

注（*4）如制动管和线卡套管等。

图13材料及加工方法管子是用以聚氯乙烯或氯乙烯为主的共聚体作为主要原料，按规定的品质挤压加工而成。

夹层管的编织物是用尼龙纤维编织的。

4尺寸内外径尺寸管子的内外径尺寸见表2。

表2 单位：mm备注）通常用○印。

带（）的尽可能不用。

厚度偏差量管子的厚度偏差量都在0.3mm以下。

长度管子的长度见表3。

表3 单位：mm注（*5）长度的最小单位为10mm。

5标记方法及部件号码标记方法： V. TUBE，(内径)×(外径) × (长度)6品质管子管子的品质按照HES D 3214(乙烯管的一般试验方法)进行试验，必须符合表5的规定。

编织物管壁中间层的编织物纤维为24根（条），必须符合表4的规定。

表5-1表5-2表5-3备注1）VT-DH2除阻燃性及耐压性外，其它都用剥离到编织物层的管子进行试验。

备注2）制品内部充填性用作设计上的参考，以制品的实测值表示。

表5-47检查外观检查外观检查可用目测，必须符合表5的规定。

7.2 尺寸检查尺寸检查按HES D 3214(乙烯管的一般试验方法)规定的尺寸测定方法进行测定，必须符合4项的规定。

7.3性能检查性能检查按HES D 3214(乙烯管的一般试验方法)进行试验，必须符合6项的规定。

HES焊接强度试验基准

a)材料相同板厚相同﹙材料抗拉强度相同板厚相同﹚——按相应的抗拉剪切强度可作参考。
例：JSC270E/1.6t和JSC270E/1.6t
选等级270Mpa/1.6t的抗拉剪切强度 7662N作基准。（参照表1 中a）
b）材料相同板厚不同﹙材料抗拉强度相同板厚不同﹚——按较薄板的抗拉剪切强度作基准。
电阻点焊强度试验标准
抗拉剪切强度试验
公称板厚的选取：
1.在板厚和材质不同钢板焊接时，计算钢板抗拉强度与钢板厚度的积，取积较小的钢板厚度作为公称板厚。
2.三层以上焊接时，试片的形状为图3，尺寸按照表1。这种情况下的剪切强度试验，如图3a)、b)所示，要在相关部件材质间进行。
3.三层以上焊接，板厚或材质不同时，试片尺寸，计算不同相关部件材质的抗拉强度与板厚的积，取较小值的板材的板厚为公称板厚。
工程间检查、初物检查至少各一次
工程间检查量产准备阶段（工艺参数确认）（需要提供报告）初物检查
工程间检查依据工厂的质量管理规定量产准备阶段都做
-抗拉剪切强度试验
•试片的形状及尺寸 ——JIS Z 3136 尺寸的选取见表1
图2为两层钢板的焊接
焊接强度试验标准
电阻点焊强度试验标准
抗拉剪切强度试验
焊、软钎焊、闪光焊、凸焊和摩擦焊，符号依据表3。 • 注意：
焊接强度分：A/B/C三个等级；图面没有标识为B级。
补充说明焊接强度等级（HES A 1018）焊接方法类别
1、基本符号
焊接符号的表示方法
2、辅助符号
焊接符号的表示方法
3、类别符号
焊接符号的表示方法
4、图纸标注方法
焊接符号的表示方法 a) 电阻点焊的图面示例1

LS1206B

⑴ 测流过程中，勿经受猛烈的撞击。 ⑵ 旋桨表面的油污、泥沙、可用清水，或汽油清洗干净，保持清洁、干燥。 ⑶ 冰期测流，当更换垂线位置时，仪器出水后旋桨表面结冰，可用开水浇化，切勿使用明火烘烤。 ⑷ 旋桨供螺纹与旋轴联结在一起，当流速较大时，应用钩形扳手并紧，特别是泵站管道测流，当测流结束瞬间，反向流速会使旋桨倒转，很可能使螺纹自动松脱。但严禁使用钢丝钳之类的工具来并紧，以免损坏转动套。
LS1206B旋桨式流速仪 LS1206B旋桨式流速仪
• • • • • • • 旋桨回转直径:60mm 旋桨水力螺距:120mm 仪器起转速:<0.06m/s 测速范围:0.06-7.0m/s 工作水深:0.1-1.2m 检定精度:m<±1.2% 讯号频率:一转两个
主要技术指标
1．旋桨回转直径：Φ60mm 2．旋桨水力螺距：H=120mm 3．仪器起转速：V0≤0.06m/s（普通品） V0≤0.05m/s（优等品） 4．仪器测速范围：0.07～7m/s （普通品） 0.05～7m/s （优等品） 5．仪器工作水深：0.1～1.2m （测杆）
水流速度的测量原理，实际上乃是测定流速仪旋桨在预定测速历时内的平均转率，代入上式而计算出流速。
使用注意事项（1 使用注意事项（1）
本仪器旋桨为一种优良的工程塑料。十几年来，通过各种试验证明：这种塑料旋桨具有优良的抗冲击性，耐腐蚀性，耐大气老化和优异的热稳定性，符合本仪器的技术标准。 a. 旋桨的质量控制着仪器性能，表征检定公式 K值。因此，在使用中应注意：
LS1206B型旋桨式流速仪型旋桨式流速仪
Model LS 1206B Propeller Type Current Meter
XK34-132-0026

HES标准教材简要介绍(培训课本)

记录的必要性
3 设变信息变更栏填写规则（HES H 037）
3 设变信息
3 设变信息
3 设变信息
3 设变信息设变号（HES H 065、063）
图面内容图纸发行概略
备注
新出图
新图（*4）、量产图（*4）、新出图
暂定图、试制图
变更、改更改图（ *5 ）、改订图追加号
三件一套
天津
原图一套
三件一套
原图一套
三件一套
三件一套
翻译后的原图一套
译后返回
三件一套翻译三件一套担当；伊刘玲
天津分公司内部使用的图样由其工艺工装室发放
发第二原图二套（一套购买管理部存档、一套发供方）
注：为了节约时间，对于项目组在海南或天津的情况，可由购买写委托书，由其资料管理部门代为发放
三件一套
45°倒角
2 制图信息尺寸附加符号（HES A 2103）
当正圆的表示十分明确时，直径前的Φ可以省略
2 制图信息尺寸附加符号（HES A 2103）
当圆心坐标已标注的场合，允许省略R
2 制图信息尺寸附加符号（HES A 2103）
小R的标注
正确
错误
即使中心坐标未标注，如果容易分辩，也可以省略 R。
HB 不会产生重大事故的零件。
1 图面信息未注公差等级（HES A3025 ）
表示未注公差等级为1级表示未注公差等级为2级
1 图面信息未注公差等级（HES A3025 ）
1 图面信息未注公差等级（HES A3025 ）
1 图面信息未注公差等级（HES A3025 ）
1 图面信息未注公差等级举例

Schmersal PROTECT系列产品说明书

Depending on the complexity and number of safety circuits, the Schmersal Group provides solutions for reliable signal analysis based on safety control modules and safety controllers with an array of visualisation and diagnostic possibilities.PROTECT SRB modules ■ M ulti-purpose use, easy installation, low cost solution ■ S RB-E-series covers a broad range of applications with eight versions ■ S RB EXi modules with ATEX, IECEx and INMETRO approvals ■ S RB301ST for lift applications,certified in accordance with EN 81-20/50Safe signal processingThe complete Schmersal portfolioPROTECT- SELECT ■ U p to 6 safety functions can be realised ■ A daptation to individual requirements thanks to simple parameterisation ■ V arious parameters such as short circuit monitoring can be configured ■ S ave space in the control cabinet ■ D isplay of clear text messages duringtroubleshootingComplexSafety relay module PROTECT SRB-ESafety controller PROTECT PSCPROTECT SELECT safety moduleHigh costLow costSimpleNumber of safety functions1 - 34 - 9> 10Modular safety compact controller PROTECT PSC1■Freely programmable compact controller PSC1-C-10 and PSC1-C-100■ P rogramming software SafePLC2: Modern, object oriented application development environment ■ »Save Drive Monitoring« module (SDM) monitors up to 12 axes ■ U niversal communication interface for all common field-bus systems ■ M odular expansion with up to 272 inputs/ outputsCentral structure:I/O expansion modulesModular compact controller PROTECT PSC1PROTECT PSC1-C-10: up to 2 expansion modules / 64 I/OsPROTECT PSC1-C-100: up to 8 expansion modules / 272 I/OsThe compact controller PROTECT PSC1-C-10 can be expanded with up to 2 I/O expansion modules.A mixture of centralised and decentralised structures can be used.The compact controller PROTECT PSC1-C-100 can be expanded with up to 8 I/O expansion modules.A mixture of centralised and decentralised structures can be used.Central structure:I/O expansion modulesDecentral structure:Expandable with the remote I/O moduleDecentral structure:Expandable with theremote I/O module• • •Safe Drive Monitoring (SDM) for PROTECT PSC 1Safe drive monitoring for up to 12 axesFor safe drive monitoring many safety features are supported:■ S afe shut-down: Safe Torque OFF (STO), Safe Brake Control (SBC)■ S afe stopping: Safe Stop 1 (SS1), Safe Stop 2 (SS2), Safe Operating Stop (SOS)■ S afe movement: Safely-Limited Speed (SLS), Safe Speed Range (SSR), Safe Direction (SDI),Safely-Limited Acceleration (SLA), Safe Acceleration Range (SAR)■ S afe monitoring: Safe Speed Monitor (SSM), Safe Cam (SCA)■ S afe Positioning: Safely-Limited Position (SLP), Safely-Limited Increment (SLI),Safely Emergency Limit (SEL)The drive monitoring is carried out depending on the application requirements, with one or two encoder systems.The following encoder signals are supported:■ 1 encoder system: TTL, SIN/COS, SSI (Gray code / binary code)■ 2 Encoder systems: TTL, SIN/COS, SSI (Gray code / binary code), Resolver, HTLPROTECT - SELECTMulti-functional Safety Module with Program Selection Function With the multi-functional PROTECT SELECT compact safety module, the engineer has greater flexibilityduring configuration of the safety device and its subsequent integration into the machine functions.Four different programs are available. Each program can beprecisely adapted – without any programming knowledge,simply with the menu and clear text messages – to the specificapplication case. This allows for example the release delayand the de-bounce time to be set individually, and numerousparameters such as the cross-wire monitoring to be set asrequired – a definite advantage in comparison to safety relaymodules.With every application program the user profits from numerousfunctions – such as:■C onnection of up to six dual-channel safety switching devices(with or without potential) up to PL e / SIL 3■S afety semi-conductor and relay outputs with STOP 0 orSTOP 1 function■S afe analogue monitoring of temperature and other processvariables■F ree assignment of start-up tests, periodic tests, auto-start,manual start■C ross-wire detection■ Display of clear text messages during troubleshooting■ Input filter for safety devices with contact bouncePROTECT SRB-E modulesSafe signal processing for a range of applicationsAll eight versions of the new family of safety relay modules PROTECT SRB-E can be used in applications up toCat. 4 / PL e in accordance with EN ISO 13849-1 and up to SIL 3 in accordance with EN 62061 / IEC 61508.A major advantage of the new PROTECT SRB-E series is its multi-functionality which allows all the variants to be usedwith several dozen existing SRB modules. Each module can be configured for up to eleven different applications via asimple control element. All conventional safety sensors and electromechanical safety equipment can be monitored.The drastic reduction in the number of variants and the clear display of the relevant functions makes it considerablyeasier for the machine manufacturer to select the right module for their particular application. Adjustable configuration and applicationsFlexible■1 or 2 channel signal evaluation■C ontact configuration can be selected for the sensors■S tart / Reset functionswith monitoring■I nput expanders for4 sensors up to PL e■C ascading via safe inputs■C ombined evaluationfor 2 safety guards■T wo-hand control monitoring ■S TOP Category 0 and 1■U p to 5 safety outputs■S afety category 4, PL e semi-conductor outputsup to 5.5 ACompact■I nstallation width for all devicevariants 22.5 mm■U p to 10 safe inputs and5 safe outputs■U p to 4 signalling outputs■H older for equipment label■U p to 24 connecting terminals User-friendly■U p to 11 different applicationscan be selected■M onitoring of all conventionalsafety switchgear■S afety level of up to PL e / SIL 3can be achieved■S imple adjustmentusing rotary switch■S elected application canbe locked using seal■Q uick response time (< 10 ms)to request■E xcellent switching performanceand short cycle times■S lot-in terminationwith codingFunction setting via rotary knob modeAdjustment of drop-out delay (stop category 1)via rotary switch for timeConnection option for all standard safety switchgearPROTECT SRB-EXi modules Safe signal processing withthe intrinsic safety of ignition protectionThese devices combines functional safety, reliable signal analysis and safety approval with explosion protection. They monitor the connected sensors, reset buttons,emergency stop devices, locking mechanisms and safety sensors with the intrinsic safety of the "i" ignition protection.The sensors can be installed or implemented in zones 1 / 2 and 21 / 22.The PROTECT SRB-EXi modules can be installed in a suitable switching cabinet in gas explosion safety zone 2.Approvals category (2) GD / 3 G:■A TEX ■I ECEx ■I NMETROUser SoftwareProgramming software SafePLC2Programming software SafePLC2 for PROTECT PSC1■M odern, object oriented application development environment■P reconfigured elements for safe electronic and electromechanicalswitching devices■E asy reuse of application code by macros■P rogramming assistance by various search functions■S imple signal tracking by different colour representation andstatus messages■E asy to detect safety functions through practice oriented librariesfor logic,Safe Drive Monitoring, SD-bus and encoder elements■C onfigurable user permissionsThe Schmersal GroupThe details and data referred to have been carefully checked. Technical amendments and errors possible.In the demanding field of machine safety, the owner-managed Schmersal Group is one of the international market leaders. The company, which was founded in 1945,has a workforce of about 2000 people and seven manufacturing sites on three continents along with its own companies and sales partners in more than 60 nations.Customers of the Schmersal Group include global players from the area of mechanical engineering and plant manufacturing as well as operators of machinery. They profit from the company‘s extensive expertise as a provider of systems and solutions for machine safety. Furthermore, Schmersal specialises in various areas including foodstuff production, the packaging industry, machine tool industry, lift switchgear, heavy industry and the automotive industry.A major contribution to the systems and solutions offered by the Schmersal Group is made by tec.nicum with its comprehensive range of services: certified Functional Safety Engineers advise machinery manufacturers and machinery operators in all aspects relating to machinery andoccupational safety – and do so with product and manufacturer neutrality. Furthermore, they plan and realise complex solutions for safety around the world in close collaboration with the clients.Safety Products Safety Systems Safety Services■ Safety switches and sensors, solenoid interlocks■ Safety controllers and safetyrelay modules, safety bus systems ■ Optoelectronic and tactile safety devices■ Automation technology:position switches, proximity switches ■ tec.nicum academy – Seminars and training ■ tec.nicum consulting – Consultancy services ■ tec.nicum engineering –Design and technical planning ■ tec.nicum integration – Execution and installation■ Complete solutions for safeguarding hazard areas ■ Individual parametrisation and programming of safety controllers ■ Tailor-made safety technology –be it for individual machines or a complex production line■ Industry-specific safety solutions 2.000 / L+W / 11.2017 / Teile-Nr. 103014039 / EN / Ausgabe 02*103014039#。

KSB 水泵产品说明书

1 Time between end of installation and start of test run ≤ 1 hour - 1 of 2 -
1070.7503/03-EN / © KSB Service GmbH, Frankenthal 2021 / Subject to technical modification without prior notice.
Comments
Date, signature
- 2 of 2 -
Mat. No.: 01738239
Scope of services
Scope of services
Connecting the pipes to the pump Checking that the piping is connected without transmitting any stresses or strains as per operating manual Connecting the pump set to the power supply (after separating the motor shaft from the pump shaft if applicable) Lubricating the pump Priming the pump Venting the pump Checking the shaft seal Checking the direction of rotation of the motor Conducting a test run (≤ 1 hour)1) Final installation inspection with final report and customer meeting

HES12-060200-3中文资料

H HiTRON04/22/2002UNIVERSAL OR U.S. INPUT RANGE AC TO DC EXTERNALWALLMOUNT ADAPTERS SINGLE OUTPUT 12 WATTSSWITCHING POWER SUPPLIES HES12 OR HES12B SERIESFEATURES:LOW COST WALLMOUNT ADAPTER DIVERSE AC PLUGS A V AILABLE MEET DIVERSE SAFETY STANDARDS EMI MEET EN 55022 OR FCC CLASS B CE MARKING COMPLIANCEGENERAL SPECIFICATIONEfficiency: Typ. 80.5%.Switching Frequency: Typ. 56-76K Hz.@ full load. Circuit Topology: Free-running flyback circuit.Transient Response: Output voltage returns typ. 1mSfollowing a 25% load change.Safety Standard: UL1950/EN60950.Class II. Power Density: 2.3 Watts. / Cubic Inch.Operating Temperature: 0 to +40°C. Storage Temperature: -20 to +85°C.Temperature Coefficient: Typ. 0.04% /°C. Cooling: Free air convection.Construction: Impact resistant thermo-plasticenclosure case.Wallmount or Desktop format.Notes: (1) All measurements are at nominal input, full load, and +25°C unless otherwise specified.(2) Load regulation is measured at 230Vac or 120Vac in percentage to indicate the change in output voltage as the load is varied from half load to full load (±%). (3) The exact obtainable load regulation depends upon the output cord selected and load current. Upper data are for 6 ft. (2 m) cord AWG#18 wires.SPECIFICATIONINPUT SPECIFICATIONInput Voltage: HES12 typ. 90-264Vac, rating 100-240Vac.HES12B typ. 90-132Vac, rating 120Vac. Input Connector:HES12: WM1 (U.S.2-blade)/WM3 (Euro-stecker)/DT8(IEC320-2P).HES12B: WM1 (U.S.2-blade). Input Frequency: 47-63Hz. Inrush Current:HES12: Typ. 28A @ 230Vac by adding thermister. HES12B: Typ. 22.5A @ 115Vac.Input Current: HES12 Typ. 0.15A @ 230Vac.HES12B Typ. 0.24A @ 115Vac. Dielectric Withstand: Meet IEC950. EMI: Meet EN 55022 or FCC Class B.Hold-up Time: Typ. 13.2mS@115Vac/42.0mS@230Vac.OUTPUT SPECIFICATIONOutput Voltage: See Ratings Chart. Output Current: See Ratings Chart. Output Wattage : Typ. 12 Watts. Output Connector: Optional. Line Regulation: Typ. 0.1%. Load Regulation: Typ. ±2-3%.Noise & Ripple : Typ. 1.0% peak to peak. OVP: Built-in. By Zener diode clamping. Adjustability: Factory set.Overload Protection (OLP): Fully protected against outputoverload or short circuit. Typ. 120-150% max. load.Consult the factory for special OLP settingMODEL NO. DESCRIPTION: HES12 or B - XXX YYY – S 04/22/2002INPUT AC PLUG: HES12: [1]WM1, [3]WM3, [8]DT8HES12B: WM1OUTPUT CURRENTOUTPUT VOLTAGESERIES NAME (Hitron External Switcher): About 12W.OUTPUT VOLTAGE/CURRENT RATINGS CHARTSINGLE OUTPUTMODEL NO. AC INPUT AC PLUG O/P VOLTAGE O/P CURRENT FORMATHES12-033240-1,3,8 90-264Vac WM1/WM3/DT8 3.3V 2.40A Wallmount/DesktopHES12B-033240 120Vac WM1 3.3V 2.40A Wallmount HES12-050240-1,3,8 90-264Vac WM1/WM3/DT8 5.0V 2.40A Wallmount/DesktopHES12B-050240 120Vac WM1 5.0V 2.40A Wallmount HES12-060200-1,3,8 90-264Vac WM1/WM3/DT8 6.0V 2.00A Wallmount/DesktopHES12B-060200 120Vac WM1 6.0V 2.00A Wallmount HES12-065180-1,3,8 90-264Vac WM1/WM3/DT8 6.5V 1.80A Wallmount/DesktopHES12B-065180 120Vac WM1 6.5V 1.80A Wallmount HES12-075160-1,3,8 90-264Vac WM1/WM3/DT87.5V 1.60A Wallmount/DesktopHES12B-075160 120Vac WM1 7.5V 1.60A Wallmount HES12-090130-1,3,8 90-264Vac WM1/WM3/DT89.0V 1.30A Wallmount/DesktopHES12B-090130 120Vac WM1 9.0V 1.30A WallmounttHES12-120100-1,3,8 90-264Vac WM1/WM3/DT812.0V 1.00A Wallmount/Desktop HES12B-120100 120Vac WM1 12.0V 1.00A Wallmount HES12-150080-1,3,8 90-264Vac WM1/WM3/DT815.0V0.80A Wallmount/DesktopHES12B-150080 120Vac WM1 15.0V0.80A Wallmount HES12-240050-1,3,8 90-264Vac WM1/WM3/DT824.0V0.50A Wallmount/DesktopHES12B-240050 120Vac WM1 24.0V0.50A Wallmount HES12-480025-1,3,8 90-264Vac WM1/WM3/DT848.0V0.25A Wallmount/DesktopHES12B-480025 120Vac WM1 48.0V0.25A Wallmount MECHANICAL DIMENSIONS: MM [INCHES] WEIGHT: 113g (4.0 Oz.)。

Lab manual 1303说明书

Apr 17, 1995 LAB MANUAL 1303.0 1303 LIQUID LIMIT DETERMINATIONAASHTO Designation T 891303.1DEFINITIONThe Liquid Limit of a soil is that water content, as determined in accordancewith the following procedure, at which the soil passes from a plastic to aliquid state.1303.2APPARATUSA. Evaporating Dish - A porcelain dish (preferably unglazed) about115mm (4 1/2 inches) in diameter.B. Spatula - A spatula having a blade about 75mm (3 inches) in lengthand about 20mm (3/4 inches) in width.C. Liquid Limit Device - A mechanical device consisting of a brass dishand carriage as described and shown in AASHTO T 89.D. Grooving Tool - A combined grooving tool and gauge conforming tothe dimensions as shown in AASHTO T 89.E. Containers - Suitable containers with lids which will prevent loss ofmoisture prior to and during weighing. Containers should befabricated from corrosion-resistant material. One container isneeded for each moisture content determination.F. Balance - A balance conforming to the requirements of AASHTO M231, Class C, with a readability, sensitivity of 0.01 grams and anaccuracy of 0.02 grams.G. Oven - A thermostatically-controlled, drying oven capable ofmaintaining a temperature of 110 ± 5 °C (230 ± 9 °F) for dryingmoisture samples.1303.3Adjustment of the Mechanical DeviceA. Inspection1. Check the liquid limit device to determine that it is in goodworking order.2. The pin connecting the cup shall not be worn sufficiently topermit side play.Apr 17, 1995 LAB MANUAL 1303.3A3. The screws connecting the cup to the hanger arm shall betight.4. A cup that has been grooved from use shall be replaced.5. The grooving tool shall be inspected to determine that criticaldimensions conform to AASHTO T 89.B. Adjustments1. By means of the gauge on the handle of the grooving tool, andthe adjustment plate on the liquid limit device, the height towhich the cup is lifted shall be adjusted so that the point onthe cup which comes in contact with the base is exactly 10mm± 2µm above the base.2. Determine the point on the cup which comes in contact withthe base.a. For new cups, place a piece of carbon paper on thebase. Allowing the cup to drop several times will markthe contact spot.b. For used cups, a slightly worn spot will be present.3. After the contact point is determined place a piece of maskingtape across the bottom of the cup. The edge of the tape, awayfrom the hanger, should bisect the contact spot on the cup andremain parallel with the axis of the cup hanger. See Section1303.10 for a diagram of the cup and a figure showing thelocation of the tape.4. Turn the crank until the cup is raised to its maximum height.Slide the gauge under the cup from the front. Observewhether the gauge contacts the cup or the tape. If the tapeedge and the cup are both contacted the height isapproximately correct. If not, adjust the cup untilsimultaneous contact is made.5. The adjustment plate shall then be secured by tightening thescrews. With the gauge still in place the adjustment shall bechecked by revolving the crank several times. If theadjustment is correct a slight ringing or clicking sound will beheard when the cam strikes the cam follower. If the cup israised off the gauge or no sound is heard further adjustmentsshall be made.Apr 17, 1995 LAB MANUAL 1303.3B6. Always remove the tape after completion of the adjustments. 1303.4PROCEDURE - STANDARD METHOD (AASHTO T 89, Method A)(Refer to Section 1301)A. A soil sample of about 100 grams of material passing the 425µm(#40) sieve shall be placed in the evaporating dish and thoroughlymixed with distilled or demineralized water by alternately andrepeatedly, stirring, kneading and chopping with a spatula. Furtheradditions of water shall be made in small (1-3ml) increments. Witheach increment, the water shall be thoroughly mixed with the soilbefore another increment of water is added. Take approximately a10 gram sample from the mixed soil and lay aside to season for usein the plastic limit test. (See Section 1304.)NOTE 1: Once testing has begun NO additional dry soil shall be added to the moistened soil. If too much water hasbeen added, the sample shall be discarded, or the sample shall be mixed and kneaded until natural evaporationlowers the closure point into an acceptable range.NOTE 2: Some soils absorb water more slowly than others so that it is possible to add the water so fast that a falseliquid limit value is obtained. This can be avoided if the sample is mixed thoroughly or more time is allowed.B. When sufficient water has been mixed with the soil to form a uniformmass of stiff consistency, a sufficient quantity of this mixture is placedin the liquid cup and spread out by use of the spatula. The soil shallbe leveled with the spatula and trimmed to a depth of 100µm at thepoint of its maximum thickness.C. The soil in the cup shall be divided by a firm stroke of the groovingtool along the diameter through the centerline of the cam follower sothat a clean sharp groove of the proper dimensions will be formed.To avoid tearing of the sides of the groove or slipping of the soil cakeon the cup, 6 strokes maximum from front to back or back to frontshall be permitted. The depth of the groove should be increased witheach stroke and only the last stroke should scrape the bottom of thecup.D. The cup containing the sample shall be lifted and dropped by turningthe crank at the rate of two revolutions per second until the two sidesof the sample come in contact at the bottom of the groove along adistance of about 12mm (1/2 inch). Do not hold the base of themachine while turning the crank. Record the number of blowsrequired to close the groove. (A motorized device is acceptableprovided it produces the same liquid limit values.)NOTE 3: Frequently check the liquid limit device's adjustment and tighten thescrews connecting the brass cup to the hanger arm.March 1, 2023 LAB MANUAL 1303.4EE. A slice of soil approximately the width of the spatula extending fromedge to edge of the soil cake at right angles to the groove, includingthat portion of the groove in which the soil flowed together, shall beremoved and placed in a suitable container.F. The container and soil shall be weighed and the weight recorded.The soil in the container shall be oven-dried to a constant weight at110 ± 5 °C (230 ± 9 °F) and weighed. This weight shall be recordedand the loss in weight due to drying shall be recorded as the weightof water. (1303 Figure 1)G. Transfer the remaining soil in the cup to the evaporating dish. Washand dry the cup and grooving tool in preparation for the next trial.H. The foregoing operations shall be repeated for at least two additionalportions of the sample to which sufficient water has been added tobring the soil to a more fluid condition. The object of this procedureis to obtain samples of such consistency that at least onedetermination will be made in each of the following ranges: 25-35blows, 20-30 blows and 15-25 blows so the range in the threedeterminations is at least 10 blows. (EXAMPLE: 28-23-18 blows.)Ideally, a spread greater than 10 blows is desired in thedeterminations.March 1 , 2023 LAB MANUAL 1303.61303.6CALCULATIONS for STANDARD METHOD (Three points)A. The water content of the soil shall be expressed as the moisturecontent in percentage of the weight of the oven-dried soil andcalculated as follows:Weight of Water% Moisture =X 100Weight of Oven-dried SoilAs in the example (Can #1):3.02% Moisture =X 100 = 28.90.44NOTE 5: See Form #2485 (Section 1303.8)B. A "flow curve" representing the relation between moisture contentand corresponding number of blows shall be plotted on a semilogarithmic graph. The flow curve shall be a straight line drawn asnearly as possible through the three or more plotted points. SeeForm #2485 (Section 1303.8)C. Liquid Limit - The moisture content corresponding to the intersectionof the flow curve at 25 blows shall be taken as the liquid limit of thesoil. Report this value to the nearest whole number.Apr 17, 1995 LAB MANUAL 1303.8 1303.8 EXAMPLE - FORM # 2485Apr 17, 1995 LAB MANUAL 1303.9 1303.9EXAMPLE - CHART TABLES for ALTERNATE METHODApr 17, 1995 LAB MANUAL 1303.10 1303.10LIQUID LIMIT DEVICE。

ASTM 美标标准号索引-中英对照表

ASTM 美标标准号索引-中英对照表发布时间：06-11 作者：本站来源：本站点击次数：878ASTM标准中英对照标准号英文名称中文名称A1-00(2005) Standard Specification for Carbon Steel Tee Rails 碳素钢丁字轨A2-02 Standard Specification for Carbon Steel Girder Rails of Plain, Grooved, and GuardTypes普通型,带槽和防护型碳素工字钢轨A3-01(2006) Standard Specification for Steel Joint Bars, Low, Medium, and High Carbon(Non-Heat-Treated)低、中、高碳素钢鱼尾（连接）板A6/A6M-05a Standard Specification for General Requirements for Rolled Structural Steel Bars,Plates, Shapes, and Sheet Piling轧制结构钢板材、型材和薄板桩通用技术要求A20/A20M-05 Standard Specification for General Requirements for Steel Plates for PressureVessels压力容器用钢板材通用要求A27/A27M-05 Standard Specification for Steel Castings, Carbon, for General Application 通用碳素钢铸件A29/A29M-05 Standard Specification for Steel Bars, Carbon and Alloy, Hot-Wrought, GeneralRequirements for热锻及冷加工碳素钢和合金钢棒A31-04 Standard Specification for Steel Rivets and Bars for Rivets, Pressure Vessels 钢铆钉及铆钉和压力容器用棒材A34/A34M-01 Standard Practice for Sampling and Procurement Testing of Magnetic Materials 磁性材料的抽样和采购试验的标准惯例A36/A36M-05 Standard Specification for Carbon Structural Steel 碳素结构钢技术规范A47/A47M-99(2004) Standard Specification for Ferritic Malleable Iron Castings 铁素体可锻铁铸件A48/A48M-03 Standard Specification for Gray Iron Castings 灰铁铸件A49-01(2006) Standard Specification for Heat-Treated Carbon Steel Joint Bars, Microalloyed JointBars, and Forged Carbon Steel Compromise Joint Bars热处理碳素钢连接棒材，微合金连接棒材和法兰连接棒材的标准规范A53/A53M-06 Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Weldedand Seamless无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范A65-01 Standard Specification for Steel Track Spikes 钢轨道钉A66-01 Standard Specification for Steel Screw Spikes 钢质螺旋道钉A67-00(2005) Standard Specification for Steel Tie Plates, Low-Carbon and High-CarbonHot-Worked热加工低碳钢和高碳钢垫板技术规范A74-06 Standard Specification for Cast Iron Soil Pipe and Fittings 铸铁污水管及配件的技术规范A82/A82M-05a Standard Specification for Steel Wire, Plain, for Concrete Reinforcement 钢筋混凝土用无节钢丝A90/A90M-01 Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles withZinc or Zinc-Alloy Coatings镀锌和镀锌合金钢铁制品镀层重量的试验方法A99-03 Standard Specification for Ferromanganese 锰铁合金A100-04 Standard Specification for Ferrosilicon 硅铁A101-04 Standard Specification for Ferrochromium 铬铁A102-04 Standard Specification for Ferrovanadium 钒铁合金A105/A105M-05 Standard Specification for Carbon Steel Forgings for Piping Applications 管系部件用碳素钢锻件A106/A106M-06 Standard Specification for Seamless Carbon Steel Pipe for High-TemperatureService高温用无缝碳素钢管A108-03e1 Standard Specification for Steel Bar, Carbon and Alloy, Cold-Finished 优质冷加工碳素钢棒材技术规范A109/A109M-03 Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent),Cold-Rolled冷轧碳素钢带技术规范A111-99a(2004)e1 Standard Specification for Zinc-Coated (Galvanized) Iron Telephone and TelegraphLine Wire电话和电报线路用镀锌"铁"丝规格A116-05 Standard Specification for Metallic-Coated, Steel Woven Wire Fence Fabric 镀锌钢丝编织栏栅网A121-99(2004) Standard Specification for Metallic-Coated Carbon Steel Barbed Wire 镀锌刺钢丝A123/A123M-02 Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and SteelProducts钢铁产品的锌镀层（热浸镀锌）技术规范A125-96(2001) Standard Specification for Steel Springs, Helical, Heat-Treated 热处理螺旋形钢弹簧A126-04 Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe Fittings 阀门、法兰和管配件用灰铁铸件A128/A128M-93(2003) Standard Specification for Steel Castings, Austenitic Manganese 钢铸件,奥氏体锰A131/A131M-04ae1 Standard Specification for Structural Steel for Ships 海船用结构钢A132-04 Standard Specification for Ferromolybdenum 钼铁合金A134-96(2005) Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16and Over)电熔(电弧)焊钢管(NPS为16英寸和16英寸以上)A135/A135M-06 Standard Specification for Electric-Resistance-Welded Steel Pipe 电阻焊钢管A139/A139M-04 Standard Specification for Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and Over) 电熔(电弧)焊钢管(4英寸以上的)A143/A143M-03 Standard Practice for Safeguarding Against Embrittlement of Hot-Dip GalvanizedStructural Steel Products and Procedure for Detecting Embrittlement热浸镀锌结构钢制品防脆裂措施和探测脆裂的程序A144-04 Specification for Ferrotungsten 铁钨合金规范A146-04 Standard Specification for Molybdenum Oxide Products 氧化钼制品A148/A148M-05 Standard Specification for Steel Castings, High Strength, for Structural Purposes 结构用高强度钢铸件A153/A153M-05 Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware 钢铁制金属构件上镀锌层(热浸) A159-83(2001) Standard Specification for Automotive Gray Iron Castings 汽车用灰铁铸件A167-99(2004) Standard Specification for Stainless and Heat-Resisting Chromium-Nickel SteelPlate, Sheet, and Strip不锈钢和耐热铬镍钢板、薄板及带材A176-99(2004) Standard Specification for Stainless and Heat-Resisting Chromium Steel Plate,Sheet, and Strip不锈钢和耐热铬钢板、薄板及带材A178/A178M-02 Standard Specification for Electric-Resistance-Welded Carbon Steel andCarbon-Manganese Steel Boiler and Superheater Tubes电阻焊接碳素钢钢管及碳锰钢锅炉和过热器管的技术规范A179/A179M-90a(2005) Standard Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchangerand Condenser Tubes热交换器和冷凝器用无缝冷拉低碳钢管A181/A181M-01 Standard Specification for Carbon Steel Forgings, for General-Purpose Piping 普通锻制碳素钢管的规格A182/A182M-05a Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges, ForgedFittings, and Valves and Parts for High-Temperature Service高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件A183-03 Standard Specification for Carbon Steel Track Bolts and Nuts 钢轨用碳素钢螺栓和螺母A184/A184M-06 Standard Specification for Fabricated Deformed Steel Bar Mats for ConcreteReinforcement混凝土加筋用变形钢筋编织网A185/A185M-06e1 Standard Specification for Steel Welded Wire Reinforcement, Plain, for Concrete 钢筋混凝土用焊接钢丝结构A192/A192M-02 Standard Specification for Seamless Carbon Steel Boiler Tubes for High-PressureService高压用无缝碳素钢锅炉管A193/A193M-06a Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for HighTemperature or High Pressure Service and Other Special Purpose Applications高温或高压设备和其他特殊用途用合金钢和不锈钢螺栓材料A194/A194M-06a Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure orHigh Temperature Service, or Both高温和高压设备用碳素钢与合金钢螺栓和螺母的规格A197/A197M-00(2006) Standard Specification for Cupola Malleable Iron 化铁炉用可锻铸铁A203/A203M-97(2003) Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel 压力容器用镍合金钢板A204/A204M-03 Standard Specification for Pressure Vessel Plates, Alloy Steel, Molybdenum 压力容器用钼合金钢板A209/A209M-03 Standard Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler andSuperheater Tubes锅炉和过热器用无缝碳钼合金钢管A210/A210M-02 Standard Specification for Seamless Medium-Carbon Steel Boiler and SuperheaterTubes锅炉和过热器用无缝碳钼合金钢管A213/A213M-06ae1 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler,Superheater, and Heat-Exchanger Tubes无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管A214/A214M-96(2005) Standard Specification for Electric-Resistance-Welded Carbon SteelHeat-Exchanger and Condenser Tubes热交换器与冷凝器用电阻焊接碳素钢管A216/A216M-04 Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, forHigh-Temperature Service高温下使用的适合于熔焊的碳素钢铸件规格A217/A217M-04 Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for 适合高温受压零件用合金钢和马氏体不锈钢铸件Pressure-Containing Parts, Suitable for High-Temperature ServiceA220/A220M-99(2004) Standard Specification for Pearlitic Malleable Iron 珠光体可锻铁A225/A225M-03 Standard Specification for Pressure Vessel Plates, Alloy Steel,Manganese-Vanadium-Nickel压力容器用锰矾镍合金钢板A227/A227M-06 Standard Specification for Steel Wire, Cold-Drawn for Mechanical Springs 机械弹簧用冷拉钢丝A228/A228M-02 Standard Specification for Steel Wire, Music Spring Quality 乐器用优质弹簧钢丝A229/A229M-99(2005) Standard Specification for Steel Wire, Oil-Tempered for Mechanical Springs 机械弹簧用油回火的钢丝A230/A230M-05 Standard Specification for Steel Wire, Oil-Tempered Carbon Valve Spring Quality 阀门用油回火优质碳素钢弹簧丝A231/A231M-04 Standard Specification for Chromium-Vanadium Alloy Steel Spring Wire 铬钒合金钢弹簧丝A232/A232M-05 Standard Specification for Chromium-Vanadium Alloy Steel Valve Spring QualityWire阀门用优质铬钒合金钢弹簧丝A234/A234M-06 Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steelfor Moderate and High Temperature Service中温与高温下使用的锻制碳素钢及合金钢管配件A239-95(2004) Standard Practice for Locating the Thinnest Spot in a Zinc (Galvanized) Coating onIron or Steel Articles用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法A240/A240M-06b Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate,Sheet, and Strip for Pressure Vessels and for General Applications压力容器用耐热铬及铬镍不锈钢板、薄板及带材A242/A242M-04e1 Standard Specification for High-Strength Low-Alloy Structural Steel 高强度低合金结构钢A247-67(1998)e1 Standard Test Method for Evaluating the Microstructure of Graphite in Iron Castings 铁铸件中石墨显微结构评定试验方法A249/A249M-04a Standard Specification for Welded Austenitic Steel Boiler, Superheater,Heat-Exchanger, and Condenser Tubes锅炉、过热器、换热器和冷凝器用焊接奥氏体钢管A250/A250M-05 Standard Specification for Electric-Resistance-Welded Ferritic Alloy-Steel Boiler andSuperheater Tubes锅炉和过热器用电阻焊铁素体合金钢管A252-98(2002) Standard Specification for Welded and Seamless Steel Pipe Piles 焊接钢和无缝钢管桩A254-97(2002) Standard Specification for Copper-Brazed Steel Tubing 铜焊钢管规格A255-02e1 Standard Test Methods for Determining Hardenability of Steel 测定钢淬透性用末端淬火试验的标准试验方法A262-02ae3 Standard Practices for Detecting Susceptibility to Intergranular Attack in AusteniticStainless Steels奥氏体不锈钢晶间浸蚀敏感性的检测A263-03 Standard Specification for Stainless Chromium Steel-Clad Plate 耐腐蚀铬钢包覆板材,薄板材及带材技术规范A264-03 Specification for Stainless Chromium-Nickel Steel-Clad Plate 包覆的不锈铬镍钢板,薄板及带材规格A265-03 Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel Plate 镍和镍基合金包覆钢板规格A266/A266M-03a Standard Specification for Carbon Steel Forgings for Pressure Vessel Components 压力容器部件用碳素钢锻件规格A268/A268M-05a Standard Specification for Seamless and Welded Ferritic and Martensitic StainlessSteel Tubing for General Service一般设备用无缝和焊接铁素体与马氏体不锈钢管A269-04 Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubingfor General Service一般设备用无缝和焊接奥氏体不锈钢管A270-03a Standard Specification for Seamless and Welded Austenitic Stainless Steel SanitaryTubing卫生设施用无缝钢和焊接奥氏体不锈钢管A275/A275M-06 Standard Test Method for Magnetic Particle Examination of Steel Forgings 钢锻件的磁粉检查试验方法A276-06 Standard Specification for Stainless Steel Bars and Shapes 不锈钢棒材和型材A278/A278M-01 Standard Specification for Gray Iron Castings for Pressure-Containing Parts forTemperatures Up to 650°F (350°C)适用于650F容压部件用灰铸铁件的技术规范A283/A283M-03 Standard Specification for Low and Intermediate Tensile Strength Carbon SteelPlates低和中等抗拉强度碳素钢板A285/A285M-03 Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- andIntermediate-Tensile Strength压力容器用低和中等抗拉强度的碳素钢板A288-91(2003) Standard Specification for Carbon and Alloy Steel Forgings for Magnetic RetainingRings for Turbine Generators涡轮发电机磁性定位环用碳素钢和合金钢锻件A289/A289M-97(2003) Standard Specification for Alloy Steel Forgings for Nonmagnetic Retaining Rings forGenerators发电机非磁性定位环用合金钢锻件的技术规范A290/A290M-05 Standard Specification for Carbon and Alloy Steel Forgings for Rings for ReductionGears减速器环用碳素钢和合金钢锻件A291/A291M-05 Standard Specification for Steel Forgings, Carbon and Alloy, for Pinions, Gears andShafts for Reduction Gears减速器小齿轮、齿轮和心轴用碳素钢和合金钢锻件A295/A295M-05 Standard Specification for High-Carbon Anti-Friction Bearing Steel 高碳耐磨轴承钢技术规范A297/A297M-97(2003) Standard Specification for Steel Castings, Iron-Chromium andIron-Chromium-Nickel, Heat Resistant, for General Application一般用耐热铬铁与镍铬铁合金钢铸件规格A299/A299M-04 Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon 压力容器用锰硅碳钢板A302/A302M-03 Standard Specification for Pressure Vessel Plates, Alloy Steel,Manganese-Molybdenum and Manganese-Molybdenum-Nickel压力容器用锰钼和锰钼镍合金钢板A304-05e2 Standard Specification for Carbon and Alloy Steel Bars Subject to End-QuenchHardenability Requirements有末端淬火淬透性要求的合金钢棒材的技术规范A307-04 Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI TensileStrength抗拉强度为60000psi的碳素钢螺栓和螺柱的技术规范A308/A308M-03 Standard Specification for Steel Sheet, Terne (Lead-Tin Alloy) Coated by theHot-Dip Process经热浸处理镀有铅锡合金的薄板材的技术规范A309-01 Standard Test Method for Weight and Composition of Coating on Terne Sheet by theTriple-Spot Test用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法A311/A311M-04 Standard Specification for Cold-Drawn, Stress-Relieved Carbon Steel Bars Subjectto Mechanical Property Requirements有机械性能要求的消除应力的冷拉碳素钢棒A312/A312M-06 Standard Specification for Seamless, Welded, and Heavily Cold Worked AusteniticStainless Steel Pipes无缝和焊接奥氏体不锈钢管A313/A313M-03 Standard Specification for Stainless Steel Spring Wire 不锈钢弹簧丝技术规范A314-97(2002) Standard Specification for Stainless Steel Billets and Bars for Forging 锻造用不锈及耐热钢坯及钢棒规格A319-71(2001) Standard Specification for Gray Iron Castings for Elevated Temperatures forNon-Pressure Containing Parts高温无压部件用灰铁铸件A320/A320M-05a Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials forLow-Temperature Service低温用合金钢螺栓材料规格A321-90(2001) Standard Specification for Steel Bars, Carbon, Quenched and Tempered 经淬火和回火的碳素钢棒A322-06 Standard Specification for Steel Bars, Alloy, Standard Grades 合金钢棒材.级别A323-05 Standard Specification for Ferroboron 硼铁规格A324-73(2004) Standard Specification for Ferrotitanium 钛铁合金A325M-05 Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa MinimumTensile Strength [Metric]经热处理最小抗拉强度为830Mpa的热处理钢结构螺栓A325-06 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksiMinimum Tensile Strength经热处理最小抗拉强度为120/106ksi的热处理钢结构螺栓A327-91(2006) Standard Test Methods for Impact Testing of Cast Irons 铸铁冲击试验方法A327M-91(2006) Standard Test Methods for Impact Testing of Cast Irons (Metric) 铸铁冲击试验方法(米制) A328/A328M-05 Standard Specification for Steel Sheet Piling 薄钢板桩A333/A333M-05 Standard Specification for Seamless and Welded Steel Pipe for Low-TemperatureService低温用无缝与焊接钢管规格A334/A334M-04a Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes forLow-Temperature Service低温设备用无缝与焊接碳素和合金钢管A335/A335M-06 Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-TemperatureService高温用无缝铁素体合金钢管A336/A336M-06 Standard Specification for Alloy Steel Forgings for Pressure and High-TemperatureParts压力与高温部件用合金钢锻件规格A338-84(2004) Standard Specification for Malleable Iron Flanges, Pipe Fittings, and Valve Parts forRailroad, Marine, and Other Heavy Duty Service at Temperatures Up to 650°F(345°C)铁路,船舶和其他重型装备在温度达到650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件A340-03a Standard Terminology of Symbols and Definitions Relating to Magnetic Testing 有关磁性试验用符号和定义的术语A341/A341M-00(2005) Standard Test Method for Direct Current Magnetic Properties of Materials Using D-CPermeameters and the Ballistic Test Methods用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法A342/A342M-04 Standard Test Methods for Permeability of Feebly Magnetic Materials 磁铁材料导磁率的试验方法A343/A343M-03 Standard Test Method for Alternating-Current Magnetic Properties of Materials atPower Frequencies Using Wattmeter-Ammeter-Voltmeter Method and 25-cmEpstein Test Frame在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25 厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法A345-04 Standard Specification for Flat-Rolled Electrical Steels for Magnetic Applications 磁设备用平轧电炉钢A348/A348M-05 Standard Test Method for Alternating Current Magnetic Properties of Materials Usingthe Wattmeter-Ammeter-Voltmeter Method, 100 to 10 000 Hz and 25-cm EpsteinFrame用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法A350/A350M-04a Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring NotchToughness Testing for Piping Components要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术规范A351/A351M-06 Standard Specification for Castings, Austenitic, for Pressure-Containing Parts 容压零件用奥氏体及奥氏体铁素体铸铁的技术规范A352/A352M-06 Standard Specification for Steel Castings, Ferritic and Martensitic, forPressure-Containing Parts, Suitable for Low-Temperature Service低温受压零件用铁素体和马氏体钢铸件规格A353/A353M-04 Standard Specification for Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel,Double-Normalized and Tempered压力容器用经二次正火及回火处理的含9％镍的合金钢板A354-04 Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, andOther Externally Threaded Fasteners淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格A355-89(2006) Standard Specification for Steel Bars, Alloys, for Nitriding 渗氮用合金钢棒A356/A356M-05 Standard Specification for Steel Castings, Carbon, Low Alloy, and Stainless Steel,Heavy-Walled for Steam Turbines蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件A358/A358M-05 Standard Specification for Electric-Fusion-Welded Austenitic Chromium-NickelStainless Steel Pipe for High-Temperature Service and General Applications高温用电熔焊奥氏体铬镍合金钢管A363-03 Standard Specification for Zinc-Coated (Galvanized) Steel Overhead Ground WireStrand地面架空线用镀锌钢丝绳A367-60(2005) Standard Test Methods of Chill Testing of Cast Iron 铸铁的激冷试验方法A368-95a(2004) Standard Specification for Stainless Steel Wire Strand 不锈钢和耐热钢丝绳的标准A369/A369M-02 Standard Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for 高温用锻制和镗孔碳素钢管和铁素体合金钢管High-Temperature ServiceA370-05 Standard Test Methods and Definitions for Mechanical Testing of Steel Products 钢制品机械测试的标准试验方法和定义A372/A372M-03 Standard Specification for Carbon and Alloy Steel Forgings for Thin-Walled PressureVessels薄壁压力容器用碳素钢及合金钢锻件A376/A376M-06 Standard Specification for Seamless Austenitic Steel Pipe for High-TemperatureCentral-Station Service高温中心站用无缝奥氏钢管A377-03 Standard Index of Specifications for Ductile-Iron Pressure Pipe 球墨铸铁压力管规范索引A380-06 Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts,Equipment, and Systems不锈钢零件、设备和系统的清洗和除垢A381-96(2005) Standard Specification for Metal-Arc-Welded Steel Pipe for Use With High-PressureTransmission Systems高压输送用金属弧焊钢管A384/A384M-02 Standard Practice for Safeguarding Against Warpage and Distortion During Hot-DipGalvanizing of Steel Assemblies防止钢组件热浸镀锌时翘曲和扭曲用安全保护A385-05 Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip) 提供高质量镀锌覆层(热浸)A387/A387M-06 Standard Specification for Pressure Vessel Plates, Alloy Steel,Chromium-Molybdenum压力容器用铬钼合金钢板A388/A388M-05 Standard Practice for Ultrasonic Examination of Heavy Steel Forgings 重型钢锻件超声波检测A389/A389M-03 Standard Specification for Steel Castings, Alloy, Specially Heat-Treated, forPressure-Containing Parts, Suitable for High-Temperature Service适合高温受压部件用经特殊热处理的合金钢铸件规格A390-06 Standard Specification for Zinc-Coated (Galvanized) Steel Poultry Fence Fabric(Hexagonal and Straight Line)饲养家禽用镀锌钢丝栏栅网(六角形和直线形)A391/A391M-01 Standard Specification for Grade 80 Alloy Steel Chain 80号合金钢链条A392-03 Standard Specification for Zinc-Coated Steel Chain-Link Fence Fabric 镀锌钢丝链环栏栅网A394-05 Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare 传动塔架用镀锌和裸露钢螺栓A395/A395M-99(2004) Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Useat Elevated Temperatures高温用铁素体球墨铸铁受压铸件A400-69(2006) Standard Practice for Steel Bars, Selection Guide, Composition, and MechanicalProperties钢棒的成分及机械性能选择指南A401/A401M-03 Standard Specification for Steel Wire, Chromium-Silicon Alloy 铬硅合金钢丝A403/A403M-06 Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings 锻制奥氏体不锈钢管配件A407-93(2004) Standard Specification for Steel Wire, Cold-Drawn, for Coiled-Type Springs 盘簧用冷拉钢丝A409/A409M-01(2005) Standard Specification for Welded Large Diameter Austenitic Steel Pipe forCorrosive or High-Temperature Service腐蚀场所或高温下使用的焊接大口径奥氏体钢管A411-03 Standard Specification for Zinc-Coated (Galvanized) Low-Carbon Steel Armor Wire 镀锌低碳钢铠装线A413/A413M-01 Standard Specification for Carbon Steel Chain 碳素钢链A414/A414M-06 Standard Specification for Steel, Sheet, Carbon, for Pressure Vessels 压力容器用碳素薄钢板A416/A416M-06 Standard Specification for Steel Strand, Uncoated Seven-Wire for PrestressedConcrete预应力混凝土用无涂层七股钢铰线A417-93(2004) Standard Specification for Steel Wire, Cold-Drawn, for Zig-Zag, Square-Formed,and Sinuous-Type Upholstery Spring Units之字形、方形、正弦形家具用弹簧元件用冷拔钢丝A418/A418M-05 Standard Test Method for Ultrasonic Examination of Turbine and Generator SteelRotor Forgings涡轮机及发电机钢转子锻件的超声波检查方法A420/A420M-06 Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steelfor Low-Temperature Service低温下用锻制碳素钢和合金钢管配件A421/A421M-05 Standard Specification for Uncoated Stress-Relieved Steel Wire for PrestressedConcrete预应力混凝土用无涂层消除应力钢丝的技术规范A423/A423M-95(2004) Standard Specification for Seamless and Electric-Welded Low-Alloy Steel Tubes 无缝和电焊低合金钢管A424-06 Standard Specification for Steel, Sheet, for Porcelain Enameling 搪瓷用钢薄板A426/A426M-05 Standard Specification for Centrifugally Cast Ferritic Alloy Steel Pipe forHigh-Temperature Service高温用离心铸造的铁素体合金钢管A427-02 Standard Specification for Wrought Alloy Steel Rolls for Cold and Hot Reduction 冷轧和热轧用锻制合金钢辊A428/A428M-01 Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or 钢铁制品上铝覆层重量的测试方法Steel ArticlesA434-06 Standard Specification for Steel Bars, Alloy, Hot-Wrought or Cold-Finished,Quenched and Tempered热轧与冷精轧经回火及淬火的合金钢棒A435/A435M-90(2001) Standard Specification for Straight-Beam Ultrasonic Examination of Steel Plates 钢板的直射束纵向超声波检验A436-84(2001) Standard Specification for Austenitic Gray Iron Castings 奥氏体灰口铁铸件A437/A437M-06 Standard Specification for Alloy-Steel Turbine-Type Bolting Material Specially HeatTreated for High-Temperature Service高温用经特殊处理的涡轮型合金钢螺栓材料A439-83(2004) Standard Specification for Austenitic Ductile Iron Castings 奥氏体可锻铸铁铸件A447/A447M-93(2003) Standard Specification for Steel Castings, Chromium-Nickel-Iron Alloy (25-12Class), for High-Temperature Service高温用镍铬铁合金钢铸件(25-12级)A449-04b Specification for Hex Cap Screws, Bolts, and Studs, Steel, Heat Treated,120/105/90 ksi Minimum Tensile Strength, General Use经淬火和回火的钢螺栓和螺柱A450/A450M-04a Standard Specification for General Requirements for Carbon, Ferritic Alloy, andAustenitic Alloy Steel Tubes碳素钢管、铁素体合金钢管及奥氏体合金钢管A451/A451M-02 Standard Specification for Centrifugally Cast Austenitic Steel Pipe forHigh-Temperature Service高温用离心铸造的奥氏体钢管A453/A453M-04 Standard Specification for High-Temperature Bolting Materials, with ExpansionCoefficients Comparable to Austenitic Stainless Steels具有同奥氏体钢相类似的膨胀系数、屈服强度为50-120Ksi(345-827MPa)的耐高温螺栓材料A455/A455M-03 Standard Specification for Pressure Vessel Plates, Carbon Steel, High-StrengthManganese压力容器用高强度碳锰钢板A456/A456M-99(2003) Standard Specification for Magnetic Particle Examination of Large CrankshaftForgings大型曲轴锻件的磁粉检查A459-97(2003) Standard Specification for Zinc-Coated Flat Steel Armoring Tape 镀锌平轧扁钢铠装带A460-94(2004)e1 Standard Specification for Copper-Clad Steel Wire Strand 包铜钢丝绳标准A463/A463M-05 Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process 热浸镀铝薄钢板A466/A466M-01 Standard Specification for Weldless Chain 非焊接碳素钢链A467/A467M-01(2006) Standard Specification for Machine and Coil Chain 机器链和盘旋链A469/A469M-06 Standard Specification for Vacuum-Treated Steel Forgings for Generator Rotors 用于发电机转子的真空处理钢锻件A470/A470M-05 Standard Specification for Vacuum-Treated Carbon and Alloy Steel Forgings forTurbine Rotors and Shafts涡轮机转子和轴用经真空处理的碳素钢和合金锻件A471-06 Standard Specification for Vacuum-Treated Alloy Steel Forgings for Turbine RotorDisks and Wheels涡轮转子转盘和转轮用真空处理合金钢锻件技术规范A472/A472M-05 Standard Test Method for Heat Stability of Steam Turbine Shafts and Rotor Forgings 蒸汽涡轮机轴及转子锻件的热稳定性的试验方法A473-01 Standard Specification for Stainless Steel Forgings 不锈和耐热钢锻件A474-03 Standard Specification for Aluminum-Coated Steel Wire Strand 包铝钢丝绳标准A475-03 Standard Specification for Zinc-Coated Steel Wire Strand 镀锌钢丝绳A476/A476M-00(2005) Standard Specification for Ductile Iron Castings for Paper Mill Dryer Rolls 造纸厂干燥辊用球墨可锻铸铁件A478-97(2002) Standard Specification for Chromium-Nickel Stainless Steel Weaving and KnittingWire铬镍不锈钢和耐热钢制编织钢丝A479/A479M-06a Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers andOther Pressure Vessels锅炉及压力容器用不锈钢和耐热钢棒与型材A480/A480M-06a Standard Specification for General Requirements for Flat-Rolled Stainless andHeat-Resisting Steel Plate, Sheet, and Strip扁平轧制耐热不锈钢厚板材、薄板材和带材通用要求A481-05 Standard Specification for Chromium Metal 金属铬A482-05 Standard Specification for Ferrochrome-Silicon 铬铁硅A483-04 Standard Specification for Silicomanganese 硅锰合金A484/A484M-06a Standard Specification for General Requirements for Stainless Steel Bars, Billets,and Forgings不锈及耐热锻钢棒,钢坯及锻件的规格A485-03 Standard Specification for High Hardenability Antifriction Bearing Steel 高淬透性耐磨轴承钢的技术规范A487/A487M-93(2003) Standard Specification for Steel Castings Suitable for Pressure Service 受压钢铸件A488/A488M-04 Standard Practice for Steel Castings, Welding, Qualifications of Procedures andPersonnel钢铸件焊接规程和工作人员的合格鉴定A489-04 Standard Specification for Carbon Steel Lifting Eyes 碳素钢吊耳A490M-04a Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, forStructural Steel Joints [Metric]最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓A490-06 Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksiMinimum Tensile Strength最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓A491-03 Standard Specification for Aluminum-Coated Steel Chain-Link Fence Fabric 镀铝钢链环栏栅结构A492-95(2004) Standard Specification for Stainless Steel Rope Wire 耐热不锈钢丝绳A493-95(2004) Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading andCold Forging冷镦和冷锻不锈钢和耐热钢丝A494/A494M-05 Standard Specification for Castings, Nickel and Nickel Alloy 镍和镍合金铸件A495-06 Standard Specification for Calcium-Silicon Alloys 硅钙合金钢技术规范A496/A496M-05 Standard Specification for Steel Wire, Deformed, for Concrete Reinforcement 钢筋混凝土用变形钢丝A497/A497M-06e1 Standard Specification for Steel Welded Wire Reinforcement, Deformed, forConcrete钢筋混凝土用焊接变形钢丝网A498-04 Standard Specification for Seamless and Welded Carbon Steel Heat-ExchangerTubes with Integral Fins无缝与焊接碳素钢,铁素体钢与奥氏体钢制有整体散热片的换热器钢管A499-89(2002) Standard Specification for Steel Bars and Shapes, Carbon Rolled from T Rails 轧制丁字钢轨用的碳素钢棒材及型材的技术规范A500-03a Standard Specification for Cold-Formed Welded and Seamless Carbon SteelStructural Tubing in Rounds and Shapes圆形与异型焊接与无缝碳素钢结构管A501-01(2005) Standard Specification for Hot-Formed Welded and Seamless Carbon SteelStructural Tubing热成型焊接与无缝碳素钢结构管A502-03 Standard Specification for Rivets, Steel, Structural 结构钢铆钉规范A503/A503M-01(2006) Standard Specification for Ultrasonic Examination of Forged Crankshafts 锻制大型曲轴的超声波检验A504/A504M-04e1 Standard Specification for Wrought Carbon Steel Wheels 锻制碳素钢轮A505-00(2005) Standard Specification for Steel, Sheet and Strip, Alloy, Hot-Rolled and Cold-Rolled,General Requirements for热轧和冷轧合金钢薄板和带材。

(完整版)SUS304性能表

常用相关国家不锈钢厚度公差标准比较日期：2007-7-25 10:54:41钢带厚度的允许偏差1、中国国家标准(GB) 单位：mm2、日本工业标准3、美国材料协会标准（ASTM）标准SUS304、SUS301钢带不同状态下标准机械性能日期：2007-6-22 8:36:56各相关国家不锈钢钢带（钢板）标准中厚度测量位置规定日期：2007-9-7 10:42:46各相关国家不锈钢钢带（钢板）标准中厚度测量位置规定1、中国国家标准（GB 4239）宽度≥600mm,在距钢带边缘大于40mm处测量2、日本工业标准（JIS G4305）测量厚度的部位，宽度≥50mm的轧制边钢带，为距其边缘25mm以上内侧的任意一点；宽度≥30mm的切边钢带，为距其边缘15mm以上内侧的任意一点。

3、美国材料协会标准（ASTM A480）宽度≥600mm的切边钢带，测量点至少距边部15mm;宽度≥600mm的轧边钢带，测量点至少距边部25mm;中外不锈钢表面状态标准介绍ASTM480不锈钢标准表面状态Q/TY3012-2003 对厚度公差执行目标的0Cr18Ni9成品厚度控制标准太钢厚度公差执行目标的0Cr18Ni9成品厚度控制标准单位：mm注：钢带头尾共20米内的厚度上、下限允许超出上表中成品厚度范围的上、下限规定。

不锈钢的计算公式日期：2007-6-6 16:12:16中国与亚洲、北美诸国（地区）以及澳大利亚的不锈钢钢号近似对照日期：2007-6-6 15:30:13中国与亚洲、北美诸国（地区）以及澳大利亚的不锈钢标准日期：2007-4-27 15:10:02日本不锈钢板（带）表面加工标准日期：2007-4-20 14:11:46不锈钢管壁厚公差选择表日期：2007-6-7 11:23:44不锈钢管管内理论爆破压力和许用压力参数表日期：2007-6-7 11:26:18（σ/f）Et]/(D-t)，其中P2：管内许可压力Mpa σ：屈服强度Mpa E：质量系数取0.85(本公司担供E=1的焊管)FQ/TY3012-2003 对厚度公差执行目标的0Cr18Ni9成品厚度控制标准日期：2007-7-4 16:08:43太钢厚度公差执行目标的0Cr18Ni9成品厚度控制标准单位：mm注：钢带头尾共20米内的厚度上、下限允许超出上表中成品厚度范围的上、下限规定。

伊顿 BECO 深层过滤标准系列产品数据表说明书

技术数据表深层过滤BECO ® 标准系列用于标准应用的深层滤网过滤板（所有文件中的多处都有此错误，请注意修改。

下文中不再重复标出。

注：红色字体为修改后的内容）伊顿的 BECO 深层滤网的标准系列可满足严苛的液体过滤要求。

该产品的标准系列涵盖从 4.0 到 0.1 µm 间的所有过滤等级，能够确保满足此范围内不同应用的要求。

BECO 标准系列深层滤网的具体优点包括：- 理想的孔隙结构，实现待分离成分的可靠过滤 - 采用优质原料制成，具有高澄清效能 - 具有高纳污能力，使用寿命长，更加经济 - 对所有原料和辅助材料实施全面质量控制 - 全程监控，确保品质如一减少和去除微生物BECO Steril S 100、Steril S 80、Steril 60、Steril 40 拥有高细菌过滤精度的 BECO 深层滤网。

这些滤网尤其适用于冷无菌灌装或液体储存。

BECO 深层滤网采用细孔结构并具有有吸附作用的电动电位，可实现高细菌过滤精度。

由于这些滤网具有卓越的胶质成分过滤性能，因此尤其适合在后续的膜过滤中作为预过滤装置使用。

微生物降低与精细过滤BECO SD 30、KDS 15、KDS 12、KD 10、KD 7、KD 5可提供高澄清效能的 BECO 深层滤网。

这些深层滤网能够有效过滤超细颗粒，并具有灭菌功效，因而尤其适用于储存和灌装前的液体无霾过滤。

澄清过滤和粗滤BECO KD 3、K 2、K 1具有大孔腔结构的 BECO 深层滤网。

这些深层滤网具有超强的颗粒纳污能力，尤其适用于澄清过滤应用。

物理数据本信息为选择 BECO 深层滤网的参考信息。

Steril S 100 26950 0.1 3.9 58.0 > 50 30Steril S 80 26800 0.2 3.9 50.0 > 80 46Steril 60 25600 0.3 3.8 50.0 > 50 60Steril 40 25400 0.4 3.8 49.0 > 50 69SD 30 24300 0.5 3.8 50.0 > 50 84KDS 15 23150 0.6 3.8 50.0 > 50 115KDS 12 23120 0.8 3.8 50.0 > 50 155KD 10 22100 1.0 3.8 50.0 > 50 185KD 7 22070 1.5 3.8 50.0 > 50 225KD 5 22050 2.0 3.8 50.0 > 50 270KD 3 22030 2.5 3.8 50.0 > 40 425K2 21020 3.0 3.8 46.0 > 50 1550K1 21010 4.0 3.8 42.0 > 60 1900透水性是不同 BECO 深层过滤介质的实验室值，而不是建议流量。

LBB120SSN资料

LBB120LBB120 is a 250V, 170mA, 20Ω2-Form-B relay. It fea-tures low on-resistance combined with enhanced peak load current handling capability.•Telecommunications •Telecom Switching •Tip/Ring Circuits•Modem Switching (Laptop, Notebook, Pocket Size)•Hookswitch •Dial Pulsing •Ground Start •Ringer Injection •Instrumentation •Multiplexers •Data Acquisition •Electronic Switching •I/O Subsystems•Meters (Watt-Hour, Water, Gas)•Medical Equipment—Patient/Equipment Isolation •Security •Aerospace•Industrial Controls•UL Recognized: File Number E76270•CSA Certified: File Number LR 43639-10•BSI Certified to:•BS EN 60950:1992 (BS7002:1992)Certificate #: 7344•BS EN 41003:1993Certificate #: 7344•Small 8 Pin DIP Package•Low Drive Power Requirements (TTL/CMOS Compatible)•No Moving Parts •High Reliability•Arc-Free With No Snubbing Circuits •3750V RMS Input/Output Isolation •FCC Compatible•VDE Compatible•No EMI/RFI Generation•Machine Insertable, Wave Solderable•Current Limiting, Surface Mount and Tape & Reel Versions AvailableApplicationsFeaturesDescriptionApprovalsDUAL POLE OptoMOS ®RelayOrdering Information Pin ConfigurationSwitching Characteristics of Normally Closed (Form B) Devices+ Control - Switch #1– Control - Switch #1+ Control - Switch #2– Control - Switch #2Load - Switch #1Load - Switch #1Load - Switch #2Load - Switch #2AC/DC Configuration PinoutLBB120Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this data sheet is not implied.Exposure of the device to the absolute maximum ratings for an extended period may degrade the device and effect its reliability.Absolute Maximum Ratings (@ 25˚ C)1 Derate Linearly 1.33 mw/˚C 2Derate Linearly 6.67 mw/˚CElectrical Characteristics*Note: If both poles operate simulataneously load current must be derated so as not to exceed the package power dissipation value.LBB120PERFORMANCE DATA*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department.LBB120Typical LED Forward Voltage Drop (N=50 Ambient Temperature = 25°C)I= 5mADC 35302520151050LED Forward Voltage Drop (V)D e v i c e C o u n t (N )LBB120Typical On-Resistance Distribution (N=50 Ambient Temperature = 25°C)(Load Current = 120mADC)3530252015105On-Resistance (Ω)D e v i c e C o u n t (N )LBB120Typical Blocking Voltage Distribution (N=50 Ambient Temperature = 25°C)35302520151050291.25293.75296.25298.75301.25303.75Blocking Voltage (V)D e v i c e C o u n t (N )LBB120Typical I F for Switch Operation (N=50 Ambient Temperature = 25°C)(Load Current = 120mADC)LED Current (mA)D e v i c e C o u n t (N )302520151050LBB120Typical I F for Switch Dropout (N=50 Ambient Temperature = 25°C)(Load Current = 120mADC 352520151050LED Current (mA)D e v i c e C o u n t (N ))LBB120Typical Turn-On Time(N=50 Ambient Temperature = 25°C)(Load Current = 120mADC; I= 5mADC)Turn-On (ms)D e v i c e C o u n t (N )35302520151050LBB120Typical Turn-Off Time(N=50 Ambient Temperature = 25°C)(Load Current = 120mADC; I = 5mADC)Turn-Off (ms)D e v i c e C o u n t (N )3530252015105LBB120Typical Load Current vs. TemperatureTemperature (°C)L o a d C u r r e n t (m A )250200150100500LBB120Typical Leakage vs. Temperature (Measured across Pins 5 & 6 or 7 & 8)Temperature (°C)L e a k a g e (µA )0.0300.0250.0200.0150.0100.005LBB120Typical Blocking Voltagevs. TemperatureTemperature (°C)B l o c k i n g V o l t a g e (V R M S )310305300295290285LBB120Typical Turn-On vs. Temperature (Load Current = 170mADC)Temperature (°C)T u r n -O n (m s )0.120.100.080.060.040.020LBB120Typical Turn-Off vs. Temperature (Load Current = 170mADC)Temperature (°C)T u r n -O f f (m s )2.5002.0001.5001.0000.500LBB120PERFORMANCE DATA**The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department.LBB120Typical LED Forward Voltage Dropvs. Temperature Temperature (°C)L E D F o r w a r d V o l t a g e D r o p (V )1.81.61.41.21.00.8LBB120Typical Turn-On vs. LED Forward Current(Load Current = 170mADC)LED Forward Current (mA)T u r n -O n (m s )0.6340.6320.6300.6280.6260.6240.622LBB120Typical Turn-Off vs. LED Forward Current(Load Current = 170mADC)LED Forward Current (mA)T u r n -O f f (m s )1.21.00.80.60.40.20LBB120Typical On-Resistance vs. Temperature (Load Current = 170mADC; I= 5mADC)Temperature (°C)O n -R e s i s t a n c e (Ω)60.00050.00040.00030.00020.00010.0000LBB120Typical I Ffor Switch Dropoutvs. Temperature(Load Current = 170mADC)Temperature (°C)L E D C u r r e n t (m A )3.02.52.01.51.00.5LBB120Typical I F for Switch Operationvs. Temperature(Load Current = 170mADC; I = 5mADC)Temperature (°C)L E D C u r r e n t (m A )3.02.52.01.51.00.5LBB120Typical Load Current vs. Load Voltage(Ambient Temperature = 25°C)I= 5mADCLoad Voltage (V)L o a d C u r r e n t (m A )200150100500-50-100-150-200LBB120Energy Rating CurveTimeL o a d C u r r e n t (A )1.21.00.80.60.40.2LBB120Dimensionsmm (inches)Mechanical Dimensions4.445 ±(.175 ±8 Pin DIP Surface Mount (“S ”Suffix)9.652 ± .381PC Board Pattern (Top View)2.540 ± .127(.300 ± .005)9.652 ± .3818 Pin DIP Through Hole (Standard)PC Board Pattern (Top View) 2.540 ± .127.1271.905 ±(.075 ±(.059 ± .005)PC Board Pattern (Top View)2.540 ± .127 .1271.193(.031)(.318 ± .005)LBB120Mechanical DimensionsTape and Reel Packaging for 8 Pin Surface Mount PackageTape and Reel Packaging for 8 Pin Flatpack PackageDimensionsmm(inches)For additional information please visit our website at: Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare’s Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to sup-port or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice.Specification: DS-LBB120-R6.0©Copyright 2002, Clare, Inc.All rights reserved. Printed in USA.6/25/02。

J-STD-033B(中文版)

SMD温湿度敏感元件作业，运输，储存，包装标准1.前言SMD零件的出现直接带来了新的挑战，而这些挑战的重心又在于包装的品质和可靠性。

本文讲述了floorlife在作业，包装，运输，的等级标准。

J-STD-020说明了湿敏元件级别，JEP113说明了标签要求周围环境中的湿气会通过包装材料渗透到包装内部，并在不同材料的表面聚结。

在组装工艺中，SMD元件贴装在PCB上时会经历超过200℃，在焊接时，湿气的膨胀会造成一些列的焊接品3.1.1和JEP-113湿气敏感设备标识JESD22-A113不气密包装可靠性测试条件要求4.2防护部分MIL-B-131阻湿材料（隔绝湿气,不透气的）-MIL-B-81705透气的，无静电的，可加热处理的MIL-D-3464活性干燥剂，MIL-I8835指示，湿度卡5.定义活性干燥剂：全新干燥剂或是经过依照推荐标准进行烘烤恢复原始规格的干燥剂6.包装MoistureBarrierBagDesiccantPouchesFoamEndCap尾部泡沫护垫HumidityIndicatorCard6.3.2材料6.3.2.1防潮袋（MBB）MBB的各项参数必须符合MIL-B-81075，第一类型必须要求的是弹性，防静电放电，机械强度和抗穿刺能力，袋子必须是可热封的。

在40℃条件下，以ASTMF392-93条件‘E’做弯曲测试，水汽传播速度测试采用ASTMF1249-90。

水汽传播速度不可大于0.002mg/100 in2在24小时内。

6.3.2.2干燥剂干燥剂必须要符合MIL-D3464，第二类型干燥剂必须要满足无尘，无腐蚀性，吸潮能力符合标准。

干燥剂必须包装在湿气可渗透入的袋子里，每个防潮袋里面装的干燥剂的量必须标注在袋子上，并且要保证防潮袋里的湿度在25℃的室温条件下保持在10%RH 以下。

在各种干燥剂里面，美军标规定了干燥剂的等级.A 级干燥剂要求最低一个单位吸收2.85 g 的水汽在20%RH 和25℃的环境下，并且要求能够维持环境状况在10%RH 以下。

新产品样本——榆次液压

GB1235-76-15×2.4 S-BSG-03-※-HP
数量 1
材料 NBR90
高压溢流阀
5
GB1235-76-28×3.5
2
GB1235-76-12×1.9
1
S-BSG-06-※-HP
GB1235-76-22×2.4
2
NBR90 NBR90 NBR90
压力控制阀
高压溢流阀
6
压力控制阀
▲卸荷溢流阀
200
★～05
5.6
★～10
★～20
400
★～35
6.4
▲型号说明
S-
BS
G-
03-
B-
2B3A- A100
N
HP
低
板式连
排油形
电气连接
噪系列号
公称尺寸压力等级
线圈符号
设计号
接
式
形式
音
S:
03
2B3A
交流：
B:★～05
A100A200
N
2B3B
不带灯插
低 BS:电磁
C:★～10
A220A240
G:板式
P=21(MPa) Q=2(L/min)
批量批量小批小批批量批量
有 Rc、G、 M 三种螺纹
插装阀
螺纹插装式溢流阀螺纹插装式单向阀
LCY-03/06-10 LCD-03/06-※-10
分体式螺纹插装式单向阀 LCDF-03/04/06/10-※-10
基板
6 通径叠加阀基础板 10 通径叠加阀基础板
与回油口连接 OFF
（无负载）
关闭状态（溢流
ON
阀设定压力

白合金资料大全

巴氏合金的国际技术指标和用途为：巴氏合金简介巴氏合金(包括锡基轴承合金和铅基轴承合金)是最广为人知的轴承材料，由美国人巴比特发明而得名，因其呈白色，又称白合金，具有减摩特性的锡基巴氏合金和铅基巴氏合金是唯一适合相对于低硬度轴转动的材料，与其它轴承材料相比，具有更好的适应性和压入性，广泛用于大型船用柴油机、涡轮机、交流发电机，以及其它矿山机械和大型旋转机械等。

巴氏合金执行标准：GB 340－76 《有色金属及合金产品牌号表示方法》GB/T 1174-1992 《铸造轴承合金》（GB 8740-1988的替代标准）Q/HY.100.001.1《轴承合金企业标准》（企业质量内控标准）巴氏合金成份巴氏合金的主要成分是锡、铅、锑、铜。

其中锑和铜，用以提高合金强度和硬度。

巴氏合金可简单地分为三种：高锡合金、高铅合金和中间合金(合金中锡和铅均占有重要比例)。

在所有这些合金系中，锑和铜均作为重要的合金化元素和硬化元素，而且其结构是由硬的、弥散于软基质中的金属间化合物组成。

巴氏合金分类按国家标准，巴氏合金可以分为锡基合金和铅基合金两种。

铅基合金的强度和硬度比锡基合金低，耐蚀性也差。

所以客户在使用巴氏合金的时候，通常选用锡基合金，其常用的牌号有zChSnSb11－6、ZChSnSb8－4、ZChSnSb8－8等。

铅基轴承合金的硬度、强度和韧性比锡基轴承合金低，常做低速、低负荷的轴承合金使用。

尽管铅基合金的性能没有锡基合金好，但是有许多客户仍然选择使用，因为它使用起来比较经济，其常用的牌号有ZChPbSb16－16－2、ZChPbSb1－16－1等。

锡基巴氏合金的国际技术指标和用途为：代号硬度HB 熔点（℃）ZCHSnSb4-4 28.6 225ZCHSnSb7.5-3 28.3 238ZCHSnSb8-8 34.3239ZCHSnSb12-3-10 29.6 185ZCHSnSb15-2-18 29.6 185ZCHSnSb11-6 30 241ZCHSnSb12-4-10 29 190ZCHSnSb8-4 24 200巴氏合金是人所周知的轴承材料，因其呈白色，又称白合金，具有减摩特性的锡基巴氏合金和铅基巴氏合金是唯一适合相对于低硬度轴转动的材料，广泛用于大型船用柴油机、涡轮机、交流发电机，以及其它矿山机械和大型旋转机械等。

SUPOR测试标准

浙江苏泊尔股份有限公司目序号测试名称录检测分类型式验证常规验证页码SEB030 SEB031 SEB032 SEB033 SEB034 SEB035洗碗机测试盐雾测试糖粉测试不粘涂层性能测试不粘涂层厚度测试不锈钢不粘涂层耐腐蚀测试铝锅不粘涂层耐腐蚀√ √ √ √ √ √ √ √ √037 038 039 040 041 0421浙江苏泊尔股份有限公司SEB036 SEB037 SEB038 SEB039 SEB040 SEB041 SEB042 SEB043 SEB044 SEB045不粘涂层附着牢度测试（非红点）不粘涂层附着牢度测试（红点）不粘涂层耐磨测试不粘涂层煎牛奶测试红点消失温度测试不粘涂层硬度测试（室温 23+/-5℃）不粘涂层硬度测试（高温）外涂层硬度外涂层附着牢度丁酮擦拭测试√ √ √ √ √ √ √ √ √ √ √ √ √ √ √043 044 045 046 047 048 049 050 051 0522浙江苏泊尔股份有限公司SEB 030洗碗机测试 Washing test范围 Scope : 洗碗机涂料产品、喷漆手柄及其他客人有要求产品 The products with dishwashing coating, handle with coating and the other product required 方法 Method: 1、将测试产品放入洗碗机中，加入 15 克 cascade 洗涤剂，调整为炊具清洗模式（90 分钟）。

Put the products inside the washing machine 15g cascade powder detergent, and adjust the machine to cookware washing mode（90mins） 2、每个循环取出观察产品表面情况，测试至少 50 个循环后取出。