LM140LAH PDF资料

LM140JAN
SNVS399A–FEBRUARY2006–REVISED MARCH2013 LM140JAN Three Terminal Positive Regulators
Check for Samples:LM140JAN
FEATURES DESCRIPTION
The monolithic3-terminal positive voltage regulators •Complete Specifications at0.5A and1.0A
employ internal current-limiting,thermal shutdown Loads
and safe-area compensation,making them •No External Components essentially indestructible.If adequate heat sinking is •Internal Thermal Overload Protection provided,they can deliver over0.5A and1.0A output
current.They are intended as fixed voltage regulators •Internal Short Circuit Current-limiting
in a wide range of applications including local(on-•Output Transistor Safe-area Compensation card)regulation for elimination of noise and
distribution problems associated with single-point
regulation.In addition to use as fixed voltage
regulators,these devices can be used with external
components to obtain adjustable output voltages and
currents.
Considerable effort was expended to make the entire
series of regulators easy to use and minimize the
number of external components.It is not necessary to
bypass the output,although this does improve
transient response.Input bypassing is needed only if
the regulator is located far from the filter capacitor of
the power supply.
Connection Diagrams
Figure1.Steel Metal Can TO Package(NDT)Figure2.TO-3Metal Can(K)
Bottom View Bottom View
See Package Number NDT0003A See Package Number K0002C
Please be aware that an important notice concerning availability,standard warranty,and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.Copyright©2006–2013,Texas Instruments Incorporated Products conform to specifications per the terms of the Texas
Instruments standard warranty.Production processing does not
necessarily include testing of all parameters.
LM140JAN
SNVS399A–FEBRUARY2006–REVISED
These devices have limited built-in ESD protection.The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)
DC Input Voltage35V
Internal Power Dissipation(2)Internally Limited Maximum Junction Temperature(T Jmax)150°C
Storage Temperature Range-65°C≤T A≤+150°C Operating Temperature Range-55°C≤T A≤+125°C
Lead Temperature(Soldering10seconds)300°C
Thermal Resistance
θJA T0−5(Still Air)232°C/W
T0−5(500LF/Min Air Flow)77°C/W
T0−3(Still Air)35°C/W
T0−3(500LF/Min Air Flow)TBD θJC T0−515°C/W
T0−34°C/W
ESD Susceptibility(3)2KV
(1)Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.Operating Ratings indicate conditions for
which the device is functional,but do not ensure specific performance limits.For ensured specifications and test conditions,see the Electrical Characteristics.The ensured specifications apply only for the test conditions listed.Some performance characteristics may degrade when the device is not operated under the listed test conditions.
(2)The maximum power dissipation must be derated at elevated temperatures and is dictated by T Jmax(maximum junction temperature),
θJA(package junction to ambient thermal resistance),and T A(ambient temperature).The maximum allowable power dissipation at any temperature is P Dmax=(T Jmax-T A)/θJA or the number given in the Absolute Maximum Ratings,whichever is lower.
(3)Human body model,100pF discharged through1.5KΩ
Quality Conformance Inspection
MIL-Std-883,Method5005-Group A
Subgroup Description Temp°C 1Static tests at25
2Static tests at125
3Static tests at-55
4Dynamic tests at25
5Dynamic tests at125
6Dynamic tests at-55
7Functional tests at25
8A Functional tests at125
8B Functional tests at-55
9Switching tests at25
10Switching tests at125
11Switching tests at-55
12Settling time at25
13Settling time at125
14Settling time at-55
2Submit Documentation Feedback Copyright©2006–2013,Texas Instruments Incorporated
Product Folder Links:LM140JAN
LM140JAN SNVS399A–FEBRUARY2006–REVISED MARCH2013
LM140H-5.0(JL140-5BXA,SXA)JAN Electrical Characteristics DC Parameters
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O(1)Output Voltage V I=8V,I L=-5mA 4.75 5.25V1,2,3
V I=8V,I L=-500mA 4.75 5.25V1,2,3
V I=20V,I L=-5mA 4.75 5.25V1,2,3
V I=20V,I L=-500mA 4.75 5.25V1,2,3
V I=35V,I L=-5mA 4.75 5.25V1,2,3
V I=35V,I L=-50mA 4.75 5.25V1,2,3
V RLine Line Regulation8V≤V I≤35V,I L=-50mA-150150mV1,2,3
8V≤V I≤25V,I L=-350mA-5050mV1,2,3
V RLoad Load Regulation V I=10V,-500mA≤I L≤-5mA-100100mV1,2,3
V I=35V,-50mA≤I L≤-5mA-150150mV1,2,3
I SCD Stand by Current Drain V I=10V,I L=-5mA-7.0-0.5mA1,2,3
V I=35V,I L=-5mA-8.0-0.5mA1,2,3
ΔI SCD Line Stand by I Drain vs.V Line8V≤V I≤35V,I L=-5mA-1.0 1.0mA1,2,3
ΔI SCD Load Stand by I Drain vs.I Load V I=10V,-500mA≤I L≤-5mA-0.50.5mA1,2,3
I OL Overload Current V I=8V,ForcedΔV O=-0.48V-2.0-0.5A1,2,3
I OS Output Short Circuit Current V I=10V-2.0-0.01A1,2,3
V I=25V-1.5-0.01A1,2,3
V I=35V-1.0-0.01A1,2,3
V O(2)Output Voltage V I=10V,I L=-5mA(1) 4.7 5.3V2
V O(3)Output Voltage V I=10V,I L=-5mA(2) 4.75 5.25V7,8A,8B ΔV O/ΔT Average Temperature Coefficient V I=10V,I L=-5mA,(3)-2.0 2.0mV/°C8A of Output Voltage25°C≤T A≤125°C
V I=10V,I L=-5mA,(3)-2.0 2.0mV/°C8B
-55°C≤T A≤25°C
(1)Tested at T A=+125°C,correlated to T A=+150°C.
(2)Tested at extremes as a set up forΔV O/ΔT tests.
(3)Calculated parameter.For calculations use V O@V I=10V,I L=−5mA.;Tested at extremes as a set up forΔV O/ΔT tests.
LM140H-5.0(JL140-5BXA,SXA)JAN Electrical Characteristics AC Parameters
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups NO Output Noise Voltage V I=10V,I L=-50mA125µV RMS7
ΔV O/ΔV I Transient Line Response V I=10V,I L=-5mA,30mV/V7
V Pulse=3V
ΔV O/ΔI L Transient Load Response V I=10V,ΔI L=-200mA, 2.5mV/mA7
I L=-50mA
ΔV I/ΔV O Ripple Rejection V I=10V,I L=-125mA,60dB4
e I=1V RMS atƒ=2400Hz,
Copyright©2006–2013,Texas Instruments Incorporated Submit Documentation Feedback3
Product Folder Links:LM140JAN
LM140JAN
SNVS399A–FEBRUARY2006–REVISED
LM140H-5.0(JL140-5BXA,SXA)JAN Electrical Characteristics DC Drift Parameters
Delta calculations performed on JAN S devices at group B,Subgroup5,only.
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O Output Voltage V I=8V,I L=-5mA-0.02V1
0.025
5
V I=8V,I L=-500mA-0.02V1
0.025
5
V I=20V,I L=-5mA-0.02V1
0.025
5
V I=20V,I L=-500mA-0.02V1
0.025
5
V I=35V,I L=-5mA-0.02V1
0.025
5
V I=35V,I L=-50mA-0.02V1
0.025
5
I SCD Stand by Current Drain V I=10V,I L=-5mA-2020%1
LM140H-12(JL140-12BXA,SXA)JAN Electrical Characteristics DC Parameters
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O(1)Output Voltage V I=15V,I L=-5mA11.412.6V1,2,3
V I=15V,I L=-0.5A11.412.6V1,2,3
V I=27V,I L=-5mA11.412.6V1,2,3
V I=27V,I L=-0.5A11.412.6V1,2,3
V I=35V,I L=-5mA11.412.6V1,2,3
V I=35V,I L=-50mA11.412.6V1,2,3
V RLine Line Regulation15V≤V I≤35V,I L=-50mA-360360mV1,2,3
15V≤V I≤32V,I L=-350mA-120120mV1,2,3
V RLoad Load Regulation V I=17V,-500mA≤I L≤-5mA-240240mV1,2,3
V I=35V,-50mA≤I L≤-5mA-360360mV1,2,3
I SCD Stand by Current Drain V I=17V,I L=-5mA-7.0-0.5mA1,2,3
V I=35V,I L=-5mA-8.0-0.5mA1,2,3
ΔI SCD Line Stand by I Drain vs.V Line15V≤V I≤35V,I L=-5mA-1.0 1.0mA1,2,3
ΔI SCD Load Stand by I Drain vs.I Load V I=17V,-500mA≤I L≤-5mA-0.50.5mA1,2,3
I OL Over Load Current V I=15V,ΔV O=-1.13V-2.0-0.5A1,2,3
I OS Output Short Circuit Current V I=17V-1.75-0.01A1,2,3
V I=32V-1.25-0.01A1,2,3
V I=35V-1.00-0.01A1,2,3
V O(2)Output Voltage V I=17V,I L=-5mA(1)11.212.7V2
82
V O(3)Output Voltage V I=17V,I L=-5mA(2)11.412.6V7,8A,8B
(1)Tested at T A=+125°C,correlated to T A=+150°C.
(2)Tested at extremes as a set up forΔV O/ΔT tests.
4Submit Documentation Feedback Copyright©2006–2013,Texas Instruments Incorporated
Product Folder Links:LM140JAN
LM140JAN SNVS399A–FEBRUARY2006–REVISED MARCH2013
LM140H-12(JL140-12BXA,SXA)JAN Electrical Characteristics DC Parameters(continued)
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
ΔV O/ΔT Average Temperature Coefficient25°C≤T A≤+125°C,(3)-3.0 3.0mV/°C8A Output Voltage V I=17V,I L=-5mA
-55°C≤T A≤25°C,(3)-3.0 3.0mV/°C8B
V I=17V,I L=-5mA
(3)Calculated parameter.For calculations use V O@V I=17V,I L=−5mA..;Tested at extremes as a set up forΔV O/ΔT tests.
LM140H-12(JL140-12BXA,SXA)JAN Electrical Characteristics AC Parameters
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups NO Output Noise Voltage V I=17V,I L=-50mA250µV RMS7
ΔV O/ΔI L Transient Load Response V I=17V,I L=-50mA, 2.5mV/mA7
ΔI L=-200mA
ΔV O/ΔV I Transient Line Response V I=17V,V Pulse=3V,30mV/V7
I L=-5mA
ΔV I/ΔV O Ripple Rejection V I=17V,I L=-125mA,55dB4
e I=1V RMS atƒ=2400Hz
LM140H-12(JL140-12BXA,SXA)JAN Electrical Characteristics DC Drift Parameters
Delta calculations performed on JAN S devices at group B,Subgroup5,only.
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O Output Voltage V I=15V,I L=-5mA-0.060.06V1
V I=15V,I L=-0.5A-0.060.06V1
V I=27V,I L=-5mA-0.060.06V1
V I=27V,I L=-0.5A-0.060.06V1
V I=35V,I L=-5mA-0.060.06V1
V I=35V,I L=-50mA-0.060.06V1
I SCD Stand by Current Drain V I=17V,I L=-5mA-2020%1
LM140H-15(JL140-15BXA)JAN Electrical Characteristics DC Parameters
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O(1)Output Voltage V I=18.5V,I L=-5mA14.215.7V1,2,3
55
V I=18.5V,I L=-500mA14.215.7V1,2,3
55
V I=30V,I L=-5mA14.215.7V1,2,3
55
V I=30V,I L=-500mA14.215.7V1,2,3
55
V I=35V,I L=-5mA14.215.7V1,2,3
55
V I=35V,I L=-50mA14.215.7V1,2,3
55
V RLine Line Regulation18.5V≤V I≤35V,I L=-350mA-150150mV1,2,3
V RLOAD Load Regulation-500mA≤I L≤-5mA,V I=20V-300300mV1,2,3
-50mA≤I L≤-5mA,V I=35V-450450mV1,2,3
I SCD Stand by Current Drain V I=20V,I L=-5mA-7.0-0.5mA1,2,3
V I=35V,I L=-5mA-8.0-0.5mA1,2,3
ΔI SCD Line Stand by I Drain vs.V Line18.5V≤V I≤35V,I L=-5mA-1.0 1.0mA1,2,3
ΔI SCD Load Stand by I Drain vs.I Load-500mA≤I L≤-5mA,V I=20V-0.50.5mA1,2,3 Copyright©2006–2013,Texas Instruments Incorporated Submit Documentation Feedback5
Product Folder Links:LM140JAN
LM140JAN
SNVS399A–FEBRUARY2006–REVISED
LM140H-15(JL140-15BXA)JAN Electrical Characteristics DC Parameters(continued)
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
I OL Overload Current ForcedΔV O=-1.43V,-2.0-0.5A1,2,3
V I=18.5V
I OS Output Short Circuit Current V I=20V-1.75-0.01A1,2,3
Output Short Circuit Current V I=35V-1.0-0.01A1,2,3
V O(2)Output Voltage V I=20V,I L=-5mA(1)14.115.9V2
V O(3)Output Voltage V I=20V,I L=-5mA(2)14.215.7V7,8A,8B
55
ΔV O/ΔT Average Temperature Coefficient25°C≤T A≤+125°C,(3)-3.75 3.75mV/°C8A Output Voltage V I=20V,I L=-5mA
Average Temperature Coefficient-55°C≤T A≤25°C,(3)-3.75 3.75mV/°C8B
Output Voltage V I=20V,I L=-5mA
(1)Tested at T A=+125°C,correlated to T A=+150°C.
(2)Tested at extremes as a set up forΔV O/ΔT tests.
(3)Calculated parameter.For calculations use V O@V I=17V,I L=−5mA..;Tested at extremes as a set up forΔV O/ΔT tests.
LM140H-15(JL140-15BXA)JAN Electrical Characteristics AC Parameters
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups NO Output Noise Voltage V I=20V,I L=-50mA300µV RMS7
ΔV O/ΔI L Transient Load ResponseΔI L=-200mA,V I=20V, 2.5mV/mA7
I L=-50mA
ΔV O/ΔV I Transient Line Response V I=20V,I L=-5mA,30mV/V7
V Pulse=3V
ΔV I/ΔV O Ripple Rejection V I=20V,I L=-125mA,53dB4
e I=1V RMS atƒ=2400Hz
LM140H-15(JL140-15BXA)JAN Electrical Characteristics DC Drift Parameters
Delta calculations performed on JAN S devices at group B,Subgroup5,only.
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O Output Voltage V I=18.5V,I L=-5mA-0.07V1
0.075
5
V I=18.5V,I L=-500mA-0.07V1
0.075
5
V I=30V,I L=-5mA-0.07V1
0.075
5
V I=30V,I L=-500mA-0.07V1
0.075
5
V I=35V,I L=-5mA-0.07V1
0.075
5
V I=35V,I L=-50mA-0.07V1
0.075
5
I SCD Stand by Current Drain V I=20V,I L=-5mA-2020%1
6Submit Documentation Feedback Copyright©2006–2013,Texas Instruments Incorporated
Product Folder Links:LM140JAN
LM140JAN SNVS399A–FEBRUARY2006–REVISED MARCH2013
LM140K-5.0(JL140-5BYA,SYA)JAN Electrical Characteristics DC Parameters
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O(1)Output Voltage V I=8V,I L=-5mA 4.75 5.25V1,2,3
V I=8V,I L=-1A 4.75 5.25V1,2,3
V I=20V,I L=-5mA 4.75 5.25V1,2,3
V I=20V,I L=-1A 4.75 5.25V1,2,3
V I=35V,I L=-5mA 4.75 5.25V1,2,3
V I=35V,I L=-0.1A 4.75 5.25V1,2,3
V RLine Line Regulation8V≤V I≤35V,I L=-0.1A-150150mV1,2,3
8V≤V I≤25V,I L=-0.5A-5050mV1,2,3
V RLoad Load Regulation V I=10V,-1A≤I L≤-5mA-100100mV1,2,3
V I=35V,-0.1A≤I L≤-5mA-150150mV1,2,3
I SCD Stand by Current Drain V I=10V,I L=-5mA-7.0-0.5mA1,2,3
V I=35V,I L=-5mA-8.0-0.5mA1,2,3
ΔI SCD Line Stand by I Drain vs.V Line8V≤V I≤35V,I L=-5mA-1.0 1.0mA1,2,3
ΔI SCD Load Stand by I Drain vs.I Load V I=10V,-1A≤I L≤-5mA-0.50.5mA1,2,3
I OL Overload Current V I=8V,ForcedΔV O=-0.48V-4.0-1.0A1,2,3
I OS Output Short Circuit Current V I=10V-4.0-0.02A1,2,3
V I=25V-3.0-0.02A1,2,3
V I=35V-2.0-0.02A1,2,3
V O(2)Output Voltage V I=10V,I L=-5mA(1) 4.7 5.3V2
V O(3)Output Voltage V I=10V,I L=-5mA(2) 4.75 5.25V7,8A,8B ΔV O/ΔT Average Temperature Coefficient V I=10V,I L=-5mA,(3)-2.0 2.0mV/°C8A Output Voltage25°C≤T A≤125°C
V I=10V,I L=-5mA,(3)-2.0 2.0mV/°C8B
-55°C≤T A≤25°C
(1)Tested at T A=+125°C,correlated to T A=+150°C.
(2)Tested at extremes as a set up forΔV O/ΔT tests.
(3)Calculated parameter.For calculations use V O@V I=10V,I L=−5mA.;Tested at extremes as a set up forΔV O/ΔT tests.
LM140K-5.0(JL140-5BYA,SYA)JAN Electrical Characteristics AC Parameters
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups NO Output Noise Voltage V I=10V,I L=-0.1A125µV RMS7
ΔV O/ΔV I Transient Line Response V I=10V,V Pulse=3V,30mV/V7
I L=-5mA
ΔV O/ΔI L Transient Load Response V I=10V,ΔI L=-400mA, 2.5mV/mA7
I L=-100mA
ΔV I/ΔV O Ripple Rejection V I=10V,I L=-350mA,60dB4
e I=1V RMS atƒ=2400Hz
Copyright©2006–2013,Texas Instruments Incorporated Submit Documentation Feedback7
Product Folder Links:LM140JAN
LM140JAN
SNVS399A–FEBRUARY2006–REVISED
LM140K-5.0(JL140-5BYA,SYA)JAN Electrical Characteristics DC Drift Parameters
Delta calculations performed on JAN S devices at group B,Subgroup5,only.
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O Output Voltage V I=8V,I L=-5mA-0.02V1
0.025
5
V I=8V,I L=-1A-0.02V1
0.025
5
V I=20V,I L=-5mA-0.02V1
0.025
5
V I=20V,I L=-1A-0.02V1
0.025
5
V I=35V,I L=-5mA-0.02V1
0.025
5
V I=35V,I L=-0.1A-0.02V1
0.025
5
I SCD Stand by Current Drain V I=10V,I L=-5mA-2020%1
LM140K-12(JL140-12BYA)JAN Electrical Characteristics DC Parameters
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O(1)Output Voltage V I=15V,I L=-5mA11.412.6V1,2,3
V I=15V,I L=-1A11.412.6V1,2,3
V I=27V,I L=-5mA11.412.6V1,2,3
V I=27V,I L=-1A11.412.6V1,2,3
V I=35V,I L=-5mA11.412.6V1,2,3
V I=35V,I L=-0.1A11.412.6V1,2,3
V RLine Line Regulation15V≤V I≤35V,I L=-0.1A-360360mV1,2,3
15V≤V I≤32V,I L=-0.5A-120120mV1,2,3
V RLoad Load Regulation V I=17V,-1A≤I L≤-5mA-240240mV1,2,3
V I=35V,-0.1A≤I L≤-5mA-360360mV1,2,3
I SCD Stand by Current Drain V I=17V,I L=-5mA-7.0-0.5mA1,2,3
V I=35V,I L=-5mA-8.0-0.5mA1,2,3
ΔI SCD Line Stand by I Drain vs.V Line15V≤V I≤35V,I L=-5mA-1.0 1.0mA1,2,3
ΔI SCD Load Stand by I Drain vs.I Load V I=17V,-1A≤I L≤-5mA-0.50.5mA1,2,3
I OL Over Load Current ForcedΔV O=-1.13V,V I=15V-4.0-1.0A1,2,3
I OS Output Short Circuit Current V I=17V-3.5-0.02A1,2,3
V I=32V-2.5-0.02A1,2,3
V I=35V-2.0-0.02A1,2,3
V O(2)Output Voltage V I=17V,I L=-5mA(1)11.212.7V2
82
V O(3)Output Voltage V I=17V,I L=-5mA(2)11.412.6V7,8A,8B
(1)Tested at T A=+125°C,correlated to T A=+150°C.
(2)Tested at extremes as a set up forΔV O/ΔT tests.
8Submit Documentation Feedback Copyright©2006–2013,Texas Instruments Incorporated
Product Folder Links:LM140JAN
LM140JAN SNVS399A–FEBRUARY2006–REVISED MARCH2013
LM140K-12(JL140-12BYA)JAN Electrical Characteristics DC Parameters(continued)
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups ΔV O/ΔT Average Temperature Coefficient25°C≤T A≤+125°C,(3)-3.0 3.0mV/°C8A Output Voltage V I=17V,I L=-5mA
-55°C≤T A≤25°C,(3)-3.0 3.0mV/°C8B
V I=17V,I L=-5mA
(3)Calculated parameter.For calculations use V O@V I=17V,I L=−5mA..;Tested at extremes as a set up forΔV O/ΔT tests.
LM140K-12(JL140-12BYA)JAN Electrical Characteristics AC Parameters
Sup-Symbol Parameter Conditions Notes Min Max Unit
groups NO Output Noise Voltage V I=17V,I L=-0.1A250µV RMS7
ΔV O/ΔI L Transient Load Response V I=17V,I L=-100mA, 2.5mV/mA7
ΔI L=-400mA
ΔV O/ΔV I Transient Line Response V I=17V,V Pulse=3V,30mV/V7
I L=-5mA
ΔV I/ΔV O Ripple Rejection V I=17V,e I=1V RMS55dB4
atƒ=2400Hz,I L=-350mA
LM140K-12(JL140-12BYA)JAN Electrical Characteristics DC Drift Parameters
Delta calculations performed on JAN S devices at group B,Subgroup5,only.
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O Output Voltage V I=15V,I L=-5mA-0.060.06V1
V I=15V,I L=-1A-0.060.06V1
V I=27V,I L=-5mA-0.060.06V1
V I=27V,I L=-1A-0.060.06V1
V I=35V,I L=-5mA-0.060.06V1
V I=35V,I L=-0.1A-0.060.06V1
I SCD Stand by Current Drain V I=17V,I L=-5mA-2020%1
LM140K-15(JL140-15BYA,SYA)JAN Electrical Characteristics DC Parameters
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O(1)Output Voltage V I=18.5V,I L=-5mA14.215.7V1,2,3
55
V I=18.5V,I L=-1A14.215.7V1,2,3
55
V I=30V,I L=-5mA14.215.7V1,2,3
55
V I=30V,I L=-1A14.215.7V1,2,3
55
V I=35V,I L=-5mA14.215.7V1,2,3
55
V I=35V,I L=-0.1A14.215.7V1,2,3
55
V RLine Line Regulation18.5V≤V I≤35V,I L=-0.5A-150150mV1,2,3
V RLoad Load Regulation V I=20V,-1A≤I L≤-5mA-300300mV1,2,3
V I=35V,-0.1A≤I L≤-5mA-450450mV1,2,3
I SCD Stand by Current Drain V I=20V,I L=-5mA-7.0-0.5mA1,2,3
V I=35V,I L=-5mA-8.0-0.5mA1,2,3
ΔI SCD Line Stand by I Drain vs.V Line18.5V≤V I≤35V,I L=-5mA-1.0 1.0mA1,2,3
ΔI SCD Load Stand by I Drain vs.I Load V I=20V,-1A≤I L≤-5mA-0.50.5mA1,2,3 Copyright©2006–2013,Texas Instruments Incorporated Submit Documentation Feedback9
Product Folder Links:LM140JAN
LM140JAN
SNVS399A–FEBRUARY2006–REVISED
LM140K-15(JL140-15BYA,SYA)JAN Electrical Characteristics DC Parameters(continued)
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
I OL Overload Current ForcedΔV O=-1.43V,-4.0-1.0A1,2,3
V I=18.5V
I OS Output Short Circuit Current V I=20V-3.5-0.02A1,2,3
V I=35V-2.0-0.02A1,2,3
V O(2)Output Voltage V I=20V,I L=-5mA(1)14.115.9V2
V O(3)Output Voltage V I=20V,I L=-5mA(2)14.215.7V7,8A,8B
55
ΔV O/ΔT Average Temperature Coefficient25°C≤T A≤+125°C,(3)-3.75 3.75mV/°C8A Output Voltage V I=20V,I L=-5mA
-55°C≤T A≤25°C,(3)-3.75 3.75mV/°C8B
V I=20V,I L=-5mA
(1)Tested at T A=+125°C,correlated to T A=+150°C.
(2)Tested at extremes as a set up forΔV O/ΔT tests.
(3)Calculated parameter.For calculations use V O@V I=20V,I L=−5mA..;Tested at extremes as a set up forΔV O/ΔT tests.
LM140K-15(JL140-15BYA,SYA)JAN Electrical Characteristics AC Parameters
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups NO Output Noise Voltage V I=20V,I L=-0.1A300µV RMS7
ΔV O/ΔI L Transient Load ResponseΔI L=-400mA,V I=20V, 2.5mV/mA7
I L=-100mA
ΔV O/ΔV I Transient Line Response V I=20V,V Pulse=3V,30mV/V7
I L=-5mA
ΔV I/ΔV O Ripple Rejection V I=20V,I L=-350mA,53dB4
e I=1V RMS at f=2400Hz
LM140K-15(JL140-15BYA,SYA)JAN Electrical Characteristics DC Drift Parameters
Delta calculations performed on JAN S devices at group B,Subgroup5,only.
Sub-Symbol Parameter Conditions Notes Min Max Unit
groups
V O Output Voltage V I=18.5V,I L=-5mA-0.07V1
0.075
5
V I=18.5V,I L=-1A-0.07V1
0.075
5
V I=30V,I L=-5mA-0.07V1
0.075
5
V I=30V,I L=-1A-0.07V1
0.075
5
V I=35V,I L=-5mA-0.07V1
0.075
5
V I=35V,I L=-0.1A-0.07V1
0.075
5
I SCD Stand by Current Drain V I=20V,I L=-5mA-2020%1
10Submit Documentation Feedback Copyright©2006–2013,Texas Instruments Incorporated
Product Folder Links:LM140JAN
LM140JAN SNVS399A–FEBRUARY2006–REVISED MARCH2013
REVISION HISTORY
Released Revision Section Originator Changes
02/07/06A New Release,Corporate format L.Lytle6MDS data sheets converted into one Corp.
data sheet format.The drift tables were
eliminated from the883section since it did not
apply.MDS data sheets MJLM140-05-H Rev
0B0,MJLM140-05-K Rev.0B0,MJLM140-12-H
Rev0B0,MJLM140-12-K Rev0B0,MJLM140-
15-H Rev0B0,and MJLM140-15-K Rev0B0
will be archived.
03/20/2013A ALL Changed layout of National Data Sheet to TI
format
Copyright©2006–2013,Texas Instruments Incorporated Submit Documentation Feedback11
Product Folder Links:LM140JAN。