热水控制阀说明书

800-543-9038 866-805-7089 203-791-8396
Technical Data Service
chilled, hot water, 60% glycol, steam to 50 psi Flow characteristic modifi ed equal percentage, unidirectional Controllable fl ow range 82°
Sizes
2” to 24"
Type of end fi tting for use with ASME/class 125/150 fl ange
Materials Body Disc Seat Shaft
Gland seal Bushings
carbon steel full lug 316 stainless steel RPTFE
17-4 PH stainless PTFE
glass backed PTFE
Media temperature range -20°F to 400°F [-30°C to 204°C]Body pressure rating ANSI Class 150Close-off pressure 285 psi
Rangeability
100:1 (for 30 deg to 70 deg range)Maximum velocity 32 FPS Leakage
bubble tight
•
Bubble tight shut-off to ANSI Class 150 Standards •Long stem design allows for 2” insulation minimum
• Valve Face-to-face dimensions comply with API 609 & MSS-SP-68•Designed to be installed between ASME/ANSI B16.5 Flanges •
Completely assembled and tested, ready for installation
Application
These valves are designed to meet the needs of HVAC and Commercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large C v values provide for an economical control valve solution for larger fl ow applications.
Dead End Service
Utilizes larger retainer ring set screws to allow the valve to be placed at the end of the line without a down stream fl ange in either fl ow direction while still holding full pressure.
MOD ON/OFF Valve
Size C v 10°20°30°40°50°60°70°80°90°F650-150SHP 2”102 1.50 6.10142639567799102F665-150SHP 2½”146 2.208.8020375580110142146F680-150SHP 3”228 3.4014325787125171221228F6100-150SHP 4”451 6.802763114171248338437451F6125-150SHP 5”7141143100180271393536693714F6150-150SHP 6”1103176615427841960782710701103F6200-150SHP 8”2064311242895207841135154820022064F6250-150SHP 10”35175321149288613361934263834113517F6300-150SHP 12”483773290677121918382660362846924837F6350-150SHP 14”685790392914164624813592489865306857F6400-150SHP 16”92871325311230222933614865663488459287F6450-150SHP 18”11400171684159638734332627085501127011400F6500-150SHP 20”144202078281932347852447590103501380014420F6600-150SHP 24”220503151260294052927890
11550
1575021000
22050
F6 Series 2-Way, ANSI Class 150 Butterfl y Valve Reinforced Tefl on Seat, 316 Stainless Disc
2-way Valves
Suitable Actuators
Valve Nominal Size
Type Non Fail-Safe
Fail-Safe
Spring Return Electronic C v
90°C v 60°Inches ANSI 150 2-way 150
150
150
102562F650-150SHP
G M S e r i e s
P R S e r i e s
A F S e r i e s
G K S e r i e s
146
80
2½
F665-150SHP
2281253F680-150SHP 4512484F6100-150SHP 7143925F6125-150SHP P K R 11036076F6150-150SHP 206411358F6200-150SHP S Y S e r i e s (2 Y e a r W a r r a n t y )
3517193410F6250-150SHP 4837266012F6300-150SHP 6857359214*F6350-150SHP 9287486516*F6400-150SHP 11400627018*F6450-150SHP 14420759020*F6500-150SHP 22050
11550
24*
F6600-150SHP
866-805-7089 203-791-8396 LATIN AMERICA / CARIBBEAN
Maximum Dimensions (Inches)
F650-150SHP 2”102 1.759.009.0019.50 4.7545/8-11 UNC 2*AF
150Spring Return F665-150SHP 2½”146 1.889.009.0020.00 5.5045/8-11 UNC 150F680-150SHP 3”228
1.929.009.0020.50 6.0045/8-11 UNC 150F6100-150SHP
4”451 2.139.009.0021.007.5085/8-11 UNC 150F650-150SHP 2”102 1.759.009.0019.50 4.7545/8-11 UNC GK 285Electronic Fail-Safe F665-150SHP 2½”146 1.889.009.0020.00 5.5045/8-11 UNC 285F680-150SHP 3”228 1.92
9.009.0020.50 6.0045/8-11 UNC 285F6100-150SHP 4”451 2.139.009.0021.00
7.50
85/8-11 UNC 150F6100-150SHP 4”451
2.139.009.0021.007.5085/8-11 UNC 2*GK 285F650-150SHP
2”102 1.759.009.0019.50 4.75
4
5/8-11 UNC GM 285Non-Spring Return Electronic Fail-Safe (K)
F665-150SHP 2½”146 1.889.009.0020.00 5.5045/8-11 UNC 285F680-150SHP 3”228 1.929.009.0020.50 6.0045/8-11 UNC 285F6100-150SHP 4”451 2.139.009.0021.007.5085/8-11 UNC 150F6100-150SHP 4”451 2.139.009.0021.007.5085/8-11 UNC 2*GM
285F650-150SHP 2”102
1.7510.0015.0014.00 4.7545/8-11 UNC PR/PK
285F665-150SHP
2½”146 1.8810.0016.0014.00 5.5045/8-11 UNC 285F680-150SHP 3”228
1.9210.0017.0015.00 6.0045/8-11 UNC 285F6100-150SHP
4”451 2.1310.0018.0016.007.5085/8-11 UNC 285F6125-150SHP 5”714
2.2510.0019.0016.008.5083/4-10 UNC 285F6150-150SHP
6”1103 2.2910.0020.0017.009.5083/4-10 UNC 285F6200-150SHP 8”2064
2.5012.0012.0032.0011.7583/4-10 UNC SY4…285F6250-150SHP 10”3517 2.8112.0012.003
3.001
4.2512
7/8-9 UNC SY4…285F6300-150SHP 12”4837 3.2312.0012.0035.0017.00127/8-9 UNC SY4…150SY5…285F6350-150SHP 14”6857 3.6214.0014.0036.0018.75121-8 UNC SY5…150SY7…285150F6400-150SHP 16”9287 4.0014.0014.0037.5021.25161-8 UNC SY8…285F6450-150SHP 18”11400 4.5014.0014.0042.2522.7516 1 1/8-8 UNC SY7…150SY8…285F6500-150SHP 20”14420 5.0014.0014.0049.5025.0020 1 1/8-8 UNC SY8…150SY10…285F6600-150SHP
24”
22050
6.06
14.00
14.00
56.25
29.50
20
1 1/4-8 UNC
SY10…
150
F6 Series 2-Way, ANSI Class 150 Butterfl y Valve
Reinforced Tefl on Seat, 316 Stainless Disc
Dimension “A” does not include flange gaskets. (2 required per valve)Application Notes
1. Valves are rated at 285 psi differential pressure in the closed position @ 100°F media temperature.
2. V alves are furnished with lugs tapped for use between ANSI Class 125/150fl anges conforming to ANSI B16.5 Standards.
3. 2-way assemblies are furnished assembled, calibrated and tested, ready for installation.
4. D imension “D” allows for actuator(s) removal without the need to remove the valve from the pipe.
5. W eather shields are available, dimensional data furnished upon request.
6. F lange gaskets (2 required, not provided with valve) MUST be used between valve and ANSI fl ange.
7. F lange bolts are not included with the valve. These are furnished by others.
D
B C
A
BHC
SHP series
valves have a preferred flow direction.
P r e f e r r e d F l o w r a t e
2*AFBUP-X1 On/Off, Spring Return, AC 24...240 V
Technical data
Electrical data Nominal voltage AC 24...240 V / DC 24...125 V
Nominal voltage frequency50/60 Hz
Power consumption in operation7 W
Power consumption in rest position 3.5 W
Transformer sizing14 VA @ AC 24 V (class 2 power source), 17 VA
@ AC 120 V, 36 VA @ AC 240 V
Electrical Connection18 GA appliance cable, 3 ft [1 m], with 1/2"
conduit connector
Overload Protection electronic thoughout 0...90° rotation
Functional data Direction of motion motor selectable by ccw/cw mounting
Direction of motion fail-safe reversible with cw/ccw mounting
Manual override 5 mm hex crank (3/16" Allen), supplied
Angle of rotation95°,
Running Time (Motor)75 s
Running time fail-safe<20 s
Noise level, motor50 dB(A)
Noise level, fail-safe62 dB(A)
Position indication Mechanically, 30...65 mm stroke
Safety data Degree of protection IEC/EN IP54
Degree of protection NEMA/UL NEMA 2
Enclosure UL Enclosure Type 2
Agency Listing cULus acc. to UL60730-1A/-2-14, CAN/CSA
E60730-1:02, CE acc. to 2014/30/EU
Listed to UL 2043 - suitable for use in air
plenums per Section 300.22(C) of the NEC and
Section 602 of the IMC
Quality Standard ISO 9001
Ambient temperature-22...122°F [-30...50°C]
Storage temperature-40...176°F [-40...80°C]
Ambient humidity Max. 95% RH, non-condensing
Servicing maintenance-free
Weight Weight9.03 lb [4.1 kg]
Materials Housing material Galvanized steel and plastic housing Electrical installation
2*AFBUP-X1
who has been properly trained in handling live electrical components perform these tasks.
Failure to follow all electrical safety precautions when exposed to live electrical components
could result in death or serious injury.
Actuators with appliance cables are numbered.
Universal Power Supply (UP) models can be supplied with 24 VAC up to 240 VAC, or 24 VDC up
to 125 VDC.
Apply only AC line voltage or only UL-Class 2 voltage to the terminals of auxiliary switches.
Mixed or combined operation of line voltage/safety extra low voltage is not allowed.
Meets cULus requirements without the need of an electrical ground connection.
Provide overload protection and disconnect as required.
Actuators may also be powered by DC 24 V.
Actuators may be powered in parallel. Power consumption must be observed.
Parallel wiring required for piggy-back applications.
Wiring diagrams
On/Off。