DIN 74-2abbr_erbores (holes) for cheese head, pan head and hexagon socket head cap screws
模具设计命名规范中英文对照大全
模具设计命名规范中英文对照大全模具英文缩写CA(cavity insert)前模SA(slide)前模行位IA(insert)前模镶件LA(lifter)前模斜顶PS（parting surface）分型面MA前模待合并体积块0临时体积块JW(jaw)铲鸡ES(ejector sleere)司筒GA（gate）入水GP边钉GB导套EG顶针板导柱STP垃圾钉模具英语术语模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode CO(core insert) SO(slide)IO (insert) LO(lifter)COOMO文件名+MDJKEP(ejector pin) RU(runner) SPKPSTBTL后模镶件后模斜顶后模镶柯后模待合并体积块后模后模行位水口边回针限位螺丝水口拉板注塑件压块司筒针流道。
北美汽车公制
1. 范围This specification （规范）encompasses（包括）criteria（标准）for stamping dies cast materials delivered in the rough-cast condition.此标准规范包括冲压模具材料在毛坯交付时的条件。
1.1类型This specification covers ferrous （亚铁）casting materials used for stamping dies.These materials include: G2500/NAAMS, G25HP/NAAMS, G3500/NAAMS,D4512/NAAMS, D5506/NAAMS, D6510/NAAMS, S0030/NAAMS, S0050A/NAAMS,S7140/NAAMS, S2333/NAAMS, TA2/NAAMS, TD2/NAAMS, and TS7/NAAMS.本规范涵盖了用于冲压模具的亚铁铸造材料。
这些材料包括:G2500 / NAAMS G25HP / NAAMS G3500 / NAAMS,D4512/NAAMS, D5506/NAAMS, D6510/NAAMS, S0030/NAAMS, S0050A/NAAMS,S7140/NAAMS, S2333/NAAMS, TA2/NAAMS, TD2/NAAMS, and TS7/NAAMS.This specification does not include or cover wrought materials（锻造材料）.此规范不包括或涵盖锻造材料1.2属性The properties of all castings are sensitive（敏感） to section size, particularly the properties of gray and ductile irons（？）. Since the cooling rate varies with thickness, the microstructure and properties will vary（不同） with thickness as well.Therefore, all properties must be referenced to specific test methods and test sample locations.（1.2属性所有铸件都有对断面很敏感的属性，,（特别是灰铁和球铁的属性？）。
德国标准和国际标准、中国标准中英文对照表(紧固件)
德国标准和国际标准、中国标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉slotted round head wood screws GB999 DIN97 开槽沉头木螺钉slotted countersunk head wood screws GB10010 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404 开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for wood constructions ISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉slotted knurled thumb screws with collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓cup head nib bolts74 DIN608 沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923 开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010 GB69-85 119 DIN965 十字槽沉头螺钉cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047 GB820-85121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2 140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3144 DIN1477 沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23 171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head 172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical heads ISO8738194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。
标准件产品中德国标准、国际标准和中国标准的中英文对照表
adjusting (shafting adjusting (shafting
rings,heavy range collars) rings,light range collars)
GB816-88
wire rope clips T-slot screws studs-metal (end=2d) hexagon socket pipe plugs,conical thread hexagon socket screw plugs,cyl. thread hexagon head pipe plugs,conical thread hexagon head screw plugs,cyl.thread socket wrenches hexagon socket cap screws hexagon socket flat point hexagon socket cone point hexagon socket dog point hexagon socket cup point set screws with set screws with set screws with set screws with ISO2936 ISO4762 ISO4026 ISO4027 ISO4028 ISO4029 GB70-85 GB77-85 GB78-85 GB79-85 GB80-85 ISO299 GB900-88
重型侧面带孔圆螺母 侧面带孔圆螺母 卡头 T型槽螺钉 双头螺柱（牙长=2D） 内六角锥型闭锁螺钉 内六角直型闭锁螺钉 外六角锥型闭锁螺钉 外六角直型闭锁螺钉 内六角扳手 内六角圆柱头螺钉 内六角平端紧定螺钉 内六角尖端紧定螺钉 内六角圆柱端紧定螺钉 内六角凹端紧定螺钉 薄型盲螺母 开槽小圆柱头螺钉 开槽大圆柱头螺钉 开槽圆柱头轴肩螺钉 开槽无头轴肩螺钉 焊接方螺母 焊接六角螺母 六角头螺栓（半牙） 六角头螺栓（全牙） 六角头螺母(1型) 细牙六角头螺母(1型) 开槽六角螺母 六角头薄螺母
标准件德标、国标对应英文
28
DIN417
Slotted set srews with full dog point
29
DIN427
Slotted set srews with chamfered end
30 31 32
DIN431 DIN432 DIN433
Pip nuts with thread External tap Washers for cheese head screws Square taper washers for
75
DIN609
Hexagon fitted bolts,long thread
76 77 78 79 80 81 82 83 84 85 86
DIN610 DIN653 DIN660 DIN661 DIN662 DIN674 DIN703 DIN705 DIN741 DIN787 DIN835
Hexagon fitted bolts short thread Knurled thumb screws thin type Round head rivets Contersunk head rivets Raised contersunk head rivets Mushroom head rivets Adjusting rings,heavy range(shafting collars) Adjusting rings,light range(shafting collars) Wire rope clips T-slot screws Studs-metal(end=2d)
Mushroom head squaห้องสมุดไป่ตู้e neck bolts(carriage bolts) Flat countersunk nib bolts
DIN74_2003_04
Diese Norm legt Maße und Bezeichnungen für Senkungen für Senkschrauben fest, deren Köpfe nicht mit den Hüllmaßen der Einheitsköpfe nach DIN EN 27721 übereinstimmen.
AG
Deutsche
Fassung
DIN 74:2003-04 Tabelle 1 — Maße für Senkung Form A
Maße in Millimeter
Für Gewindedurchmesser d1a d2 t1 H13 H13 ≈
1,6 1,8 3,7 0,9
2 2,4 4,6 1,1
Senkung, Form A
rd
ig
ck
Linsensenk-Holzschrauben nach DIN 95 und DIN 7995
Au
sd ru
Senk-Holzschrauben nach DIN 97 und DIN 7997
Bild 1 — Senkung, Form A
BEISPIEL Eine Senkung, Form A, für Gewindedurchmesser 4 mm wird wie folgt bezeichnet:
Geeignet für Senkschrauben für Stahlkonstruktionen nach DIN 7969.
Bild 2 — Senkung, Form E
BEISPIEL
Eine Senkung, Form E, für Gewindedurchmesser 12 mm wird wie folgt bezeichnet:
(标准对照)标准对照表
DIN920
开槽小圆柱头螺钉
Slotted short cheese head screws
99
DIN921
开槽大圆柱头螺钉
Slotted large cheese head screws
GB838-88
100
DIN923
开槽圆柱头轴肩螺钉
Slotted pan head screws with shoulder
侧面带孔圆螺母
Adjusting rings,light range(shafting collars)
GB816-88
84
DIN741
卡头
Wire rope clips
85
DIN787
T型槽螺钉
T-slot screws
ISO299
86
DIN835
双头螺柱(牙长＝2D)
Studs-metal (end=2d)
GB806-88
47
DIN467
滚花薄螺母
Knurled thumb thin nuts
GB807-88
48
DIN470
锁紧垫圈
Sealing washers
49
DIN471
轴用弹性挡圈
Retaining rings for shafts(external),circlips
GB894.1-86
50
平垫
Plain washers
ISO7091
13
DIN127-A
重型弹垫
Spring lock washers tang ends
GB7244
14
DIN127-B
标准弹垫
Spring lock washers square ends
小家电产品零部件中英对照
Parts Finished product序号名称 (中文)名称 (英文)参考材质产品中文名称产品英文名称序号1压铸铝合金die-casting aluminum电水壶Electric Kettle1 2限位销Limit pin煮茶器Tea Kettle 2 3组装电路板（成品电子板）PCBA Printed Circuit Board Assembly 煮蛋器Egg Cooker 3 4印刷电路板PCB Printed Circuit Board 保温盘Buffet Server4 5警示灯beacon即热式水壶Instant Electric Kettle5 6冷却液coolant咖啡机Coffee Machine/Maker 6 7破碎机crusher全自动咖啡机Automatic Coffee Machine7 8电源按键power button面包机Bread Maker8 9重置键reset button多士炉Toaster9 10不锈钢圈SS RING 油炸锅Deep Fryer10 11不锈钢SUS : steel stainless电烤箱Toaster Oven11 12流量计flow meter电炉Electric Stove12 13火线fire line电磁炉Induction Cooker13 14零线null line早餐机Breakfast Maker14 15地线earth wire蒸笼Food Steamer15 16奶嘴/接线帽wiring cap/Closed-end terminal煎锅Skillet16 17纤维硅胶管fibre silicone tube烤板Griddle 17 18塑料膜plastic film三文治Sandwich Maker18 19锡条Solder bar华夫饼机Waffle Maker19 20金属条metal bar烤肉架Grill 20 21导电条EMI gasket比萨机Pizza Oven21 22树脂Epoxy热狗机Hot dog Maker22 23磨光滑polish爆米花机Popcorn Maker23 24静电贴纸antistatic lable电烫斗Iron24 25电源线扎带cable tie蒸汽电烫斗Steam Iron25 26蜂鸣器buzzle蒸汽站电烫斗Steam station Iron26 27蒸汽挂烫机Garment Steamer 27 28蒸汽地拖Steam Mop28 29打蛋机Hand Mixer29 30绞肉机Meat Grinder 30 31橙汁机Citrus Juicer 31 32榨汁机Juice extractor 32 33手持搅拌机Hand Blender33 34果汁机Blender 34 35食物处理器Food Processor35 36豆浆机Soymilk Maker36 37吸尘器Vacuum Cleaner37 38螺钉Screw低(中)碳钢，不锈钢开罐器Can Opener38 39螺钉组合件Screw asm磨豆机Coffee Grinder 39 40螺栓/六角头螺栓Bolt低碳钢，中碳钢冰棍机ice pop maker40 41螺栓组合件Bolt asm冰淇淋机Ice cream Maker4142双头螺柱Double-head bolt低碳钢，中碳钢电饭锅Electric Rice Cooker 42 43方螺母/四角螺母Square nut低碳钢，易切削钢电压力锅Electric Pressure Cooker 43 44六角螺母/六角细牙螺母Hexagonal nut低碳钢，易切削钢沐足器Foot Bathing Machine44 45六角带介螺母Hexagonal lock nut低碳钢，易切削钢酸奶机Yogurt Maker45 46止退螺母Stop nut低碳钢，易切削钢速食面机Noodle Kettle46 47圆螺母Round nut低碳钢，易切削钢刨冰机Ice shaver47 48带槽圆螺母Round nut低碳钢，易切削钢盛酒器Bottle Chiller48 49盖形螺母Cap nut低碳钢，易切削钢远红外加暧器Infrared remote heater 49 50外齿垫螺母Nut with washer低碳钢，易切削钢风扇加热器Fan Heater50 51螺钉柱(焊接)Screw post不锈钢滴液式咖啡机ADC: Automatic drip coffee maker51 52螺母柱(焊接)Nut post 低碳钢，不锈钢52 53平垫圈/平垫/平面垫圈/快巴介子Washer/gasket低碳钢，不锈钢，非金属53 54弹簧垫圈/弹垫/弹弓介子Spring washer65Mn,1Cr18Ni9Ti54 55波形垫圈/波浪介子/波形弹性垫圈Wave washer65Mn,1Cr18Ni9Ti55 56鞍形垫圈Saddle-backed washer65Mn,1Cr18Ni9Ti56 57内齿锁紧垫圈/菊花内齿介子Internal tooth washer65Mn57 58外齿锁紧垫圈/菊花外齿介子External tooth washer65Mn58E-ring50，55钢59 59开口挡圈/卡簧/开口弹性卡簧/E型扣环/E型介子60孔用弹性挡圈/穴用C型介子Basic internal washer65Mn60 61轴用弹性挡圈/轴用C型介子Basic external washer65Mn61 62轴用定位垫圈Self locking washer65Mn62 63滚动轴承/弹子盘Rolling bearing GCr1563 64滚珠Steel ball64 65开口销Clamp pin低碳钢65 66圆柱销Insert pin中碳钢66 67弹性圆柱销Spring insert pin65Mn67 68管状铆钉/空心铆钉/鸡眼Tubular rivet20#钢，铜，黄铜68 69平头铆钉Flat head rivet 低碳钢,铝,铜,黄铜69 70沉头铆钉Countersunk rivet低碳钢,铝,铜,黄铜70 71双头铆钉Double-head rivet低碳钢,铝,铜,黄铜71 72抽芯铆钉Self-plugging rivet铝，08F钢,10#钢72 73扁圆头铆钉Oval head rivet低碳钢,铝,铜,黄铜73 Semi-tubular rivet低碳钢,铝,铜,黄铜74 74平头半空心铆钉/窝钉75扁平头半空心铆钉Semi-tubular rivet低碳钢,铝,铜,黄铜75 76扁圆头半空心铆钉Semi-tubular rivet低碳钢,铝,铜,黄铜76 77膨胀钉/定墙胶钉Expanded screw PA77 78银触点Silver contact point 银，铜镀银78 79保险管Fuse79 80保险管座Fuse holder80 81温度熔断器/保险丝/温度保险丝Thermal fuse81 82定时器Timer82 83温控器Thermostat83 84变压器Transformer8486继电器Relay86 87稳压器Voltage regulator87 88充电器Charger88 89传感器Sensor 89 90限温器Temp limiting device90 91PTC发热器PTC heater91 92负离子发生器Negative-ion generator92 93PTC过流保护器PTC ovrecurrent protector 93 94电源转换器Power inverter 94 95电子蜂鸣器Electronic buzzer 95 96水泵Water pump96 97电磁阀Electromagnet valve97 98温度表Thermometer 98 99测温计Thermometer99 100流量计Flowmeter100 101电机Motor101 102翘板开关Rocker switch102 103挡位开关Select switch103 104微动开关Micro-switch104 105按钮开关Button switch105 106拨动开关Shift switch106 107旋转开关Rotary switch107 108回弹开关Rebound Switch108 109薄膜开关Membrane switch109 110轻触开关Touch switch110 111琴键开关Piano switch/piano-key switch/ key board switch111 112接近开关/磁控开关Magnetic switch112 113蒸汽开关Steam switch113 114组合开关Combination switch114 115门锁开关Door lock switch115 116电阻Resistor116 117电容Capacitor117 118电感Inductor118 119制冷片Refrigerating piece119 120二极管Diode120 121三极管Transistor121 122可控硅Triac122 123永磁铁Permanent magnet 123 124磁环Magnetic ring镍锌磁芯124 125磁管Magnetic tube四氧化三铁粉125 126磁控管Magnetron126 127数码管Digitron127 128氖灯Neon lamp128130灯座Lamp holder130 131电池Battery131 132电源插座Power socket132 133PVC线Lead wire133 134氟塑线Lead wire134 135纤维线Lead wire135 136硅胶线Lead wire136 137高压电线Lead wire137 138电缆线Cable wire138 139排线Line wire139 140端子Terminal碳钢，铜140 141(阴/阳)插头端子(Female/Male)Plug terminal 141 142阳连接端子Male terminal 142 143阴连接端子Female terminal143 144地环端子/同地环Earth terminal铜144 145端子护套Terminal sleeve145 146引出棒Lead-out rod146 147铜带Copper strip黄铜147 148软钢带Soft steel band低碳钢镀镍148 149阴连接器Female Connector149 150阳连接器Male Connector150带引线阴连接器Connector151阴连接器壳Female Connector shell152阳连接器壳Male Connector shell153 Terminal block154端子台/接线柱/接线器/接线座电热丝Heat wire 铁铬铝丝，镍铬丝155发热管Heat element156电源线Power cord157电源线扣Cord buckle158扎带Nylon tie尼龙159扎线Cable tie塑料金属线160热缩管Shrinkage tube161纤维管Fiber tube162防漏通/硅树脂玻璃纤维套管Leakproof tube 163硅胶管Silicone tube硅橡胶164硅胶夹纤编织管Fiber Silicone tube硅橡胶165硅胶内编织管Fiber Silicone tube166硅胶外编织管Silicone fiber tube167聚四氟乙烯管/特氟龙管Teflon tube F4168聚酰亚鞍胶管Polyimide tube聚酰亚鞍169蒸气管Steam tube不锈钢170蒸汽导管Steam conduit PP171喉夹Throat clamp弹簧钢丝镀镍172导热硅脂Thermal silicone grease 174绝缘胶带Insulation tape175透明胶带Tape176双面胶纸Double adhesive tape177贴纸Paster不干胶178装饰贴纸Decorative paster179警告标贴Warning label180铭牌Rating label不干胶181爆炸图Exploded Drawing182电路原理图Circuit Diagram183接线图Wiring Diagram184产品示意图Product Illustration185丝印图Silk-screen Diagram186线圈coil187带通滤波器Band pass Filters188 CHIP线路滤波器Chip Filter189碳膜电阻Carbon Film Resistor﹝CF RES.﹞190精密电阻Precision Metal Film Resistor﹝MF RES.﹞191水泥电阻Cement Resistor﹝CM RES.﹞192线绕电阻Wire Wound Resistor﹝WW RES.﹞193热敏电阻Thermistor194金属氧化膜电阻Metal Oxide Film Resistor﹝MOF RES.﹞195半固定可变电阻Semi VR﹝SVR﹞196无感型聚丙烯膜电阻197 Polypropylene Capacitor﹝P.P/C﹞SMD网络电阻Chip Resistor Networks198放电用固定型电阻Fixed Conductive Path Resistors199网路电阻Resistor Networks200敏感电阻Sensistors201 SM电阻(非标准)SMD Resistors (non-standard)202 SMD敏感热敏电阻SMD sensitors Thermistor 203螺丝调整型可变电阻Variable Resistors W/Screw Adjustors204可变空气电容Variable Air Capacitors205可变陶瓷电容器Variable Ceramic Capacitors206可变玻璃电容Variable Glass Capacitors207聚丙烯电容Polypropylene (PP) Capacitors208聚苯乙烯电容Polystyrene Capacitors209聚乙烯电容Polyethylene Capacitors210云母电容Mica Capacitors211固定玻璃电容Glass Capacitors212电解电容Electrolytic Capacitor﹝E/C﹞213陶制电容Ceramic Capacitor﹝C/C﹞214麦拉电容Mylar (Dipped Polyester) Capacitors215钽质电容Tantalum Capacitor﹝T/C﹞216金属皮膜电容Metallized Polyester Film Capacitor﹝MPE/C﹞218金属碳化电容Metallized Polycarbonate (PC) Capacitors219 SMD陶瓷电容器Chip Capacitors Ceramic220麦拉电容Mylar (Dipped Polyester) Capacitors221麦拉电容Mylar Capacitor﹝M/C﹞222一般用途陶瓷电容General Purpose Ceramic Capacitors223金属麦拉电容Metallized Polyester (MYLAR) Capacitor224 LTD罩Led Lens﹝LED LENS﹞225二极体Diode 226桥式整流二极体Bridge Diode﹝B/Diode﹞227发光二极体Light Emitting Diode﹝LED﹞228硅控整流二极体Silicon Rectifier Diodes229稳压二极体Zener Diode﹝Z/Diode﹞230晶体管Transistor﹝TR﹞231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348名称 (中文)名称 (英文)参考材质序号英文名称英文名称参考材质序号(上/下)大身(Upper/Lower) Body PP 或钢、铝1杯盖Carafe lid PP 大身外壳Body enclosure 不锈钢或铝2(内/外)顶盖(Inner/Outer)Top cover PP 1(左/右)水尺(Left/Right) Water gauge PP 或PC 3底盖Bottom cover PP 2(前/后)水尺(Front/Back) Water gauge 4后盖Back cover PP 3水位标尺Water gauge 5内盖Inner cover PP 4不锈钢煲Stainless steel body 不锈钢6面盖Surface cover 5玻璃大身Glass body 玻璃, 硼硅玻璃7桶盖Barrel cover 6大身底Body bottom PP 8内杯盖Inner Carafe lid PP 7玻璃杯Carafe 玻璃，硼硅玻璃9外杯盖Outer Carafe lid PP 8水杯Water cup PP 10导槽盖Trough cover PP 9茶杯Teapot 不锈钢11杯座盖Jug holder cover 10量杯Measure cup 透明PP 12杯底盖Jug bottom cover 11咖啡杯Coffee cup 铝或陶瓷13瓶座盖Bottle base cover 12保温杯Warming cup 不锈钢14网格盖Mesh cover PP/ABS/PC /PA 13上壶身Upper vessel 不锈钢15豆盒盖Bean box cover 14下壶身Lower vessel 压铸铝16豆箱盖Bean box cover (上/下)手柄(Upper/Lower) Handle PP 17水箱盖Water tank cover PP/PC 15杯手柄Teapot Handle PP 18水嘴盖Sprayer cover PC/PP 16不锈钢手柄Stainless steel handle 19螺钉盖Screw cap PP/PC 17开关掣Switch / ON-OFF button PC 20水尺盖Gauge cover PC/PP 18保温开关掣Keep warm switch PC 21按键盖Press key cover 19嘴Mouth 22密封盖Seal cover 20壶嘴Spout 不锈钢23滤芯盖Filter core cover PP 21透明壶嘴Transparent Spout PP344R 24豆盒内盖Bean box inner cover 22壶盖Lid PP 或不锈钢25按键盒盖Press key box cover 23顶盖Top cover PP 26接水盘盖Drip tray cover 24前盖Front cover PP 27旅行杯盖Travel mup cover PP 25煲盖Body cover 28咖啡箱盖Coffee chamber cover PP 26杯盖Jar cover PP 29水浮封盖Float seal cover 27PCB 盖PCB cover 30蒸汽盒盖Steam box cover 28支架盖Bracket cover 31发热煲盖Boiler cover AL 29壶后盖Lid back 32手柄盖Handle cover 30壶嘴盖Spout cover PP 33电池盖Battery cover 31阻尼盖Damping cover PC 34杯手柄盖Carafe handle cover PP 32螺钉盖Screw cap PP 或PC 35单向阀盖Anti-back valve cover PP/PC 33阻尼器盖Damper cover MPPO36分水器盖Dispenser cover PC/PP 34旋钮内盖Knob inner cover PC37主体后盖Main body back cover PP 35(上/下)手柄盖(Upper/Lower) Handle cover PP38漏斗内盖Funnel inner cover PP 36手柄(上/下)盖Handle (Upper/Lower) cover PP 39开关按钮盖Switch button cover ABS 37(左/右)水尺盖(Left/Right) Water gauge cover PC 或硅橡胶40手柄装饰盖Handle deco cover 38入水盖Water inlet cover 41浓度控制盖Strength control cover PP 39QB XB TM BM002 电水壶QB XB TM BM007 普通咖啡机 胶壶口盖Spout coverPP 42外漏斗底盖Outer funnel B-cover PP 40煲底盖Body bottom coverPP 43外漏斗后盖Outer funnel R-cover PP 41底座盖Base coverPP 44杯手柄封盖Handle seal cover 42透明盖Transparent coverPC 45漏斗架后盖Funnel rear cover 43装饰盖Decoration coverABS 或不锈钢46漏斗架底盖Funnel bottom cover44液晶盖LCD Cover PC 47手柄螺钉盖Handle screw cap PP 45蒸汽盖Steam cover PP48漏斗手柄盖Funnel handle cover 46出水管盖Outlet tube cap 49活性碳提手盖Carbon handle cover 47过滤器盖Purifier cover50漏斗架手柄盖Funnel handle coverABS 48蒸汽管盖Steam tube coverPP 51PCB 封盖PCB seal cover PP/ABS 49蒸汽盒盖Steam box coverPP 52开关封盖Switch seal cover 50发热管盖Heat element cover53PCB 盒上盖PCB box upper cover PP 51上装饰盖Upper decoration coverPP 54LCD 保护盒盖LCD box cover PP/PC52上蒸汽盒盖Upper steam box cover PC 或PP 55(左/右)杯手柄盖(L-/R-)Carafe handle coverPP/PC 53水尺装饰盖Gauge decoration cover56出水口活动块盖Move block cover PP/PA/PC/ABS 54手柄装饰盖Handle deco coverPP 57发热管防护盖Heat element cover 镀锌板55按键装饰盖Press key deco coverPP 58盖衬Cover liner 56底座装饰盖Base decoration cover不锈钢59桶内衬Barrel liner 57水箱支架盖Tank bracket coverPP60按键帽Press key cap 阻燃PP58内盖Inner cover 61蒸汽帽Steam cap 59外盖Outer cover62漏斗架Funnel support PP/PC 60蒸汽槽盖Steam trough coverPP 63刀片架Blade bracket PP/ABS/PC/PA 61蒸汽制盖Steam actuator coverPC 64LCD 支架LCD support PP/ABS/PC 62杯手柄盖Teapot handle coverPP 65卡扣支架Fastener bracketPP 63灯罩孔盖Lampshade hole coverPP 66电机支架Motor bracket PP/ABS/PC 64开关孔盖Switch hole coverPP 67水箱支架Water tank bracket PP 65控制面盖Control coverPP 或PC 68水嘴支架Sprayer bracket PP 66发热盘盖Heat element cover PA 69导槽支架Trough bracket PP 67(上/下)单向阀盖Anti-back valve cover 铝或PC 70滑动支架Slide support PP/ABS/PC 68盖柄Lid knob PP 或PC 71活动支架Movable bracket 69(左/右)盖锁(Left/Right) Lid lock PC 或POM 72开关支架Switch retainer PP/PA/PC/ABS70(前/后)盖锁(Front/Back) Lid lockPC 或POM 73顶盖支架Top cover bracket71锁扣Lock POM 或PC 74滤芯支架Filter core bracket 72插座锁扣Socket lock 75蒸汽罩支架Steam cover bracket 73杯座Jar base PP 或 ABS76磨粉开关架Mill switch bracket PP/ABS/PC /PA 74(上/下)底座(Upper/Lower) Base PP 77漏斗开关架Funnel switch bracket PP/ABS/PC /PA 75内底座Inner basePP 78左装饰片支架L-decoration bracket PP/PA/PC/ABS 76煲底座Body bottom PP 79右装饰片支架R-decoration bracket PP/PA/PC/ABS 77(左/右)水尺座(Left/Right)Water gauge holder PC 或PP 80上装饰片支架U-decoration bracket 78手柄座Handle holder PP 81下装饰片支架B-decorationbracket 79开关座Switch holder 82咖啡包漏斗架CofferFunnel bracket PP80端子座Terminal holder PA66+15%GF83咖啡箱面板支架Chamber panel supportPP81阻尼座Damping holderPC84漏斗装饰片支架Funnel deco bracket 82顶盖装饰片支Top cover deco旋钮座Knob holderPC 86固定架（I/Ⅱ）Fix bracket (I/Ⅱ)PP/ABS/PC 84旋转轴座Rotate shaft holderPA6687装饰片支架（I/Ⅱ）Decoration bracket(I/Ⅱ)PP/ABS/PC 85电源插座Power socket88隔热板Thermal insulate plate PBT+30%G F/PF 86关水按钮座Water stop button base89顶盖板Top cover plate玻璃87发热盘体Heat element bodyPA 90(左/右)面板(Left/Right) Panel 88(左/右)压块(Left/Right) Press blockPP 91前面板Front panel PP/PA/PC/ABS 89(左/右)滑块(Left/Right) Slide blockPC 或POM92接线板Wiring board 覆铜硬质板90滑块压板Slide block press platePP 93开关面板Switch panel PP/ABS/PC 91(左/右)胶块(Left/Right) Rubber block硅橡胶94控制面板Control panel PP/ABS/PC92拨动块Poke block PP 95蒸汽挡板Steam baffle 93阻尼块Damping blockPC 96蒸汽帽盖板Steam cap cover plate94感温块Sensor blockAl 97上主体面板Top housing panel PP 95(左/右)固定块(Left/Right)Fix block PP 98咖啡箱面板Coffee chamber panel PP 96限位挡块Limit baffle POM 99漏斗架面板Funnel support panelABS*PC 97配重块Balance block铸铁或碳钢100密封垫固定板Seal pad fix plate PP 98隔热块Insulation block PBT+30%GF ，PF 101底座Base PP 99左隔热块Left insulation blockPBT 或硅橡胶102杯座Jug holder PP 100右隔热块Right insulation blockPBT 或硅橡胶103杯盖座Carafe lid base PP 101手柄镶块Handle insertPVC 或钢104上杯座Upper jug holder 102开关压块Switch press blockPC105后支座Back holder PP 103壶盖固定块Lid fastening block 106电机座Motor holder PP/ABS/PC /PA104壶盖连接块Lid connect block 107铰链座Hinge base 105水尺固定块Gauge fastening block不锈钢，PP 108滤芯座Filter core base PP 106螺母固定块Nut fastening block 不锈钢，PP 109酒瓶座Bottle base107手柄盖镶块Handle cover insertPVC 或PP110升降台座Lift table base ABS108开关掣装饰块ON-OFF decoration 111旅行杯座Travel mup bottom PP 109壶盖镶件Lid insert 112过滤网座Filter holder PP/ABS/PC /PA 110外盖镶件Outer cover insert113止漏阀座Anti-drip valve holder PP/PA/PC/ABS111手柄座镶件Handle holder insert不锈钢114顶杆固定座Ejection rod holder 112装饰盖镶件Decoration cover insert115保温胆固定座Jug cavity holder113开关掣镶件Switch insert PC 116升降台Lift table ADC360114电源按钮镶件Power button insert PP117旋钮KnobPP/ABS/PC 115盖板Cover plate 118滤芯钮Filter core knob PP116开关板Switch plate 119手柄按钮Handle button PP/ABS/PC 117反射板Reflecting plate 不锈钢120开关按钮Switch knobPP/ABS/PC 118装饰板Decoration platePP 121开盖按钮Lid release button 119保温板Warming plate 电解板122杯盖按钮Carafe lid button PP/PA/PC/ABS 120壶盖内板Lid inner plate PP 123出水按钮Water outlet button121壶盖底板Lid bottom platePP 124(左/右)按钮(Left/Right)Button PP/ABS/PC /硅胶122杯盖底板Carafe lid bottom plate125调节齿轮adjust gear123传热板Heat transfer plate1060(L2)铝126连管Joint tube PP124挡水板Water baffle127三通管Three outlet conduit PP/PC 125蒸汽挡板Steam baffle PP 128连接管Connectingconduit 金属/PP/硅胶126胶篮提手Plastic basket handlePP 130水嘴连管Sprayer joint tube 128开盖提手Lid-opening handlePP 或PC 131手柄挂钩Handle hook PP/ABS/PC /PA 129壶盖提手Lid handlePP 132漏斗挂钩Funnel hook PP/PA/PC/ABS 130杯盖提手Cup cover handlePP 133灯罩Lamp cover PC/AS 131滤网提手Filter handlePP 134液晶罩LCD cover PC132滤网筒提手Filter column handle PP135蒸汽罩Steam cover 133手柄内撑Handle inner support 136(内/外)透明罩(Inner/Outer)Tran sparent cover134按钮内撑Button inner support137左半球L-Half floating ball PP/PC 135支架Bracket PA66+30%GF138右半球R-Half floating ball PP/PC 136灯架Lamp support PP 139插销Insert pin 铝137灯支架Lamp holder PP 140水位球Water level ball PP 138蒸架Steam bracket 141固定栓Fix peg139勺支架Spoon bracket 硅橡胶或PP,142顶杆头Push pole head PP 140定位架Locating bracket143咖啡包淋浴头Coffee pod shower head PP 141内旋钮支架Inner knob bracket 144顶杆Push pole 142外旋钮支架Outer knob bracket 145开关杆Switch lever POM 143按键支架Press key bracketABS 146升降杆Lift lever POM144推钮支架Push button bracket147顶盖拉杆Top cover pull pole145壶盖支架Lid bracket148止漏顶杆Anti-leak top pole PP/PC 146灯罩支架Lamp cover supportPP 149按键顶杆Press key mandril 147弹性支架Spring bracket 不锈钢丝150滑动连接杆Slide lever PP148滤网支架Filter bracket PP 151提手Handle149连杆支架Lever bracket PC 152顶盖把手Top cover handle ABS 150手柄支架Handle bracket不锈钢，PP153漏斗拉手Funnel handle 151前盖支架Front cover bracketPP 154漏斗提手Funnel handlePA/PP152漏斗支架Funnel Bracket155滤网提手Filter handle PA/PP 153旋转轴支架Rotate shaft bracketPA66156咖啡箱把手Coffee chamber handle ABS 154温控器支架Thermostat bracket 157咖啡桶提手Coffee bucket handle POM 155咖啡杯手柄支架Carafe handle bracket 158瓶塞Lid insert PP 156水箱(上/下)支架Tank (upper/lower) bracket159瓶底固定塞Jug bottom fixer PP 157(上/下)开关支架(Upper/Lower) Switch retainer PP 160止漏阀Anti-drip valve PP/POM 158制冷器固定架Cooler bracket 161进水阀Inlet valvePP/PA/PC/ABS159底座盖支架Base cover bracket 162单向阀Anti-back valve PP/PC 160发热盘支架Heat element holder电解板或不锈钢163浓度控制阀Strength control valve PP 161装饰片支架Decoration bracket164压块Press block 电木PF 162(左/右)蒸汽盒支架(L-/R-)Steam box bracket 165顶杆压块Push pole press block PP 163滤网骨架Filter rib PP 166调整垫块Adjust pad block SUS304164过滤器架Purifier bracket PP 167换向块Dispensing block PP/PC165顶杆Actuating lever PC 或PP 168指示块Indicating block PP/PC 166拦杆Block rod Q235A 钢169支撑块Support block PBT+30%G F/PP/PF167连杆Lever PA66或POM 170旋钮定位块Knob fix block 168推杆Push rod PP 或PC 171杯圈固定块Carafe fix block PP 169导流杆Guide rod 172水尺固定块Gauge fix block PP/PC 170拨动杆Poke rod PC 或不锈钢174漏斗固定块Funnel fix block PP/PA/PC/ABS 172调节杆Adjust pole PA 175漏斗架固定块Funnel support fix block 173阻尼杆Damping rod POM 176出水口活动块Outlet bafflePP/PA/PC/ABS 174壶盖连杆Lid lever 177线路板固定块PCB fastener PBT+30%G F/PP/PF 175盖锁连杆Lid lock lever PP 或POM 178发热管固定块Heat element fastener PBT+30%G F/PP/PF 176连杆销Lever pin POM 179蒸汽帽装饰块Steam cap decoration 177阀芯Valve core PA 180灯圈Lamp loop PMMA178导磁环Magnetizer ring Q195181挡圈 Baffle ring 179按钮Button ABS182隔热圈Insulating ring PBT+30%G F/PF 180推钮Push button183杯环形圈Jug ring PP 181关水按钮Water stop button184主体Main housingPP 182调节旋钮Adjust knob PC 185上主体Top housing PP/PA/PC/ABS183电源按钮Power button186(前/后)主体(Front/Back)Housing 184保温按钮Keep warm button187磨豆器(上/下)主体(Upper/Lower)Grinder body 185开关掣按钮Switch button ABS 188阀体Valve body PC186(左/右)壶盖按钮(Left/Right)Lid button PP 189止漏阀体Anti-dripvalve body 187计时旋钮Timer knob 190水箱Water tank PP/AS 188调温旋钮Temperature knob PC 或PP191咖啡箱Coffee chamber PP 189手柄装饰盖包胶Handle deco cover rubber 192杯身Carafe body PP 190开关掣按钮包胶Switch button rubber193内胆身Inner bodySUS304191按键Press keyABS 194外胆身Outer body SUS304192温度按键Temperature press key195内胆底Inner body bottom SUS304193杯圈Carafe ring 不锈钢196外胆底Outer body bottom SUS304194调节圈Adjusting ring PC 197轴套Bushing PP/ABS/PC /PA 195固定圈Fixing ring PPJ801R 198灯线护套Lamp wire jacket PP 196水尺固定圈Gauge fixing ring199镶件螺母Insert nut H62197O 型圈O-shaped ring 硅橡胶200滤网Filter PP+PA 198壶嘴圈Spout ring 201滤布Filter cloth PA199装饰圈Decorative ring不锈钢或ABS 202水嘴Sprayer PP/PC200按钮装饰圈Button decorative ring不锈钢或ABS203咖啡包水嘴Coffee pod sprayer PP 201旋钮装饰圈Knob decorative ring204阀珠Anti-back valve ball PP/ABS/PC /PA202开关掣装饰圈Switch decorative ring 205阀芯Valve core PP 203煲底座装饰圈Body bottom deco ring206按键Press keyPP/ABS/PC /硅胶204密封圈 (I/II)Seal ring (I/II)硅橡胶207漏斗按键Funnel press key PA66+15%GF 205热熔圈Hot melt ring 铁丝208出水按键Water dispensing key 206过滤器圈Purifier ring209卡扣Fastener PP 207防水胶圈water proof ring硅橡胶210分水器Dispenser PP/PC208杯密封圈Cup seal ring硅橡胶211制冷器Freezer 209水尺密封圈Water gauge seal硅橡胶212糖容器Sugar container210蒸汽口密封圈Steam outlet seal 硅橡胶213水箱连接器Water tank linker PC 211出水口密封圈Outlet seal ring 硅橡胶214导水柱Dispenser post PP/PA/PC/ABS 212灯罩Lamp cover PC 215杯手柄Carafe handle PP/PC 213内灯罩Inner lamp coverPC 216漏斗架手柄Funnel support handle ABS+PC214指示灯罩Indicator coverPC 218咖啡勺Coffee spoon PP/PC 216蒸汽室罩Steam chamber coverPP 219底壳Bottom body SUS304217滤网Filter PP 220单向阀壳Anti-back valve shellPP/ABS/PC /PA 218壶盖滤网Lid filter 221搅拌漏斗Blending funnel PP/ABS/PC /PA 219滤网筒Filter cylinder PP 222保护窗口Protection window PP/ABS/PC /PA 220滤网布Filter cloth尼龙或不锈钢223螺丝套筒Screw sleeve PP/PA/PC/ABS 221滤网筒布Filter cylinder cloth不锈钢或尼龙224(左/右)漏斗(Left/Right)Funnel PP222保温杯滤网Warming cup filterPP+尼龙网225外漏斗Outer funnel 223装饰管Decoration tube不锈钢226一次性漏斗Disposable funnel224出水管Water outlet tube227水箱漏斗Water tank funnel 225硅胶管Silicone tube 硅橡胶228(左/右)水尺(Left/Right)Watergauge PC/AS/PP 226蒸汽管Steam tube 不锈钢或PP229PCB 盒PCB box PP227线槽Lead wire slot 230冰酒盒Ice chilling box 228蒸汽盒Steam boxPP 231按键盒Press key box 229发光盒Light emitting box232储冰盒Ice storage box 230阻尼器盒Damper box MPPO 233积水盒Water collection box231上蒸汽盒Upper steam boxPC 或PP234碎冰盒Crushed ice box 232过滤器盒Purifier box 235电池盒Battery box 233制冷器盒Cooler box 236蒸汽盒Steam box 234计数器盒Timer box 237藏线盒Cord storage box 235计数器盖Timer cover238电源板盒Power PCB box 236蒸汽管接头Steam tube connectorPP 239控制板盒Control PCB box237传感器接头Sensor connector PA 240LCD 保护盒LCD box PP/PC238(上/下)蒸汽接头(Upper/Lower) Steam connector PP 或硅橡胶241水箱弹簧盒Water tank spring box 239蛋托Eeg tray 242水嘴压板Sprayer press plate 不锈钢/PP/PC 240杯垫Drip plate 不锈钢243按键压板Key press plate ABS241硅胶垫Silicon mat 硅胶244蒸汽档板Steam baffle 242固定垫Fix washer 铝245冰块夹Ice clip 243吸水垫Sorption mat 海绵246保险丝夹Fuse clip不锈钢244水位球Water level ball PP 247温控器夹Thermostat clip 不锈钢245弹性球Elastic ball 硅胶248活性碳固定夹Activated carbon holder 246护套Protect bushingPP 249刀片Blade 不锈钢/PP/PC 247接触器护套Contactor sleevePP 250垫片Washer PP 248蒸汽盖护套Exhaust cover conduitPP 251连接环Connect ringSUS304249托盘Salver PP 252陶瓷环Ceramic ring 250接水盘Drip tray PP 253装饰片（I/Ⅱ）Decorationpiece(I/Ⅱ)不锈钢/PP/ABS 251茶勺盘Tea spoon tray ABS 254支撑片Support piece PC 252发热盘Heat plate 不锈钢或铸铝255左装饰片Left decoration 不锈钢/PP/ABS 253调温旋钮盘Temperature dialPC 或PP 256右装饰片Right decoration不锈钢/PP/ABS 254面膜Membrane PVC 257上装饰片Top decoration 不锈钢/PP/ABS255密封条Seal bar 258面盖装饰片Surface cover deco256装饰条Decorative strip不锈钢259后盖装饰片Back cover deco 257(左/右)搁条(Left/Right) Strip support电解板260顶杆装饰片Push pole decoration ABS 258Top cover(上/下)铁码(Upper/Lower) Metal fastener不锈钢262底盖装饰片Bottom decoration 不锈钢260码仔Fastener不锈钢263主体装饰片Housingdecoration 不锈钢/PP/ABS261手柄(上/下)码仔Handle (Upper/Lower) fastener 不锈钢264底座装饰片Base decoration piece 262煲身(上/下)码仔Body (Upper/Lower) fastener不锈钢265旅行杯装饰片Travel mup decopiece 不锈钢263压线码Strain relief/Cord clamp ABS 或PA66266左漏斗装饰片L-Funneldecoration 不锈钢/PP/ABS 264螺母柱(焊接)Nut post 低碳钢267右漏斗装饰片R-Funneldecoration 不锈钢/PP/ABS 265螺钉柱(焊接)Screw post 不锈钢268水箱盖装饰片Tank cover decoration 不锈钢/PP/ABS 266卡位销Position lock pin 269外漏斗装饰片Outer funnel decoration 不锈钢/PP/ABS 267定位销Locating pin 270水箱装饰片Tank decoration piece 不锈钢268胶片Film 271(上/下)大身装饰片(Upper/Lower)Body decoration 269弹片Spring plate 272咖啡箱装饰片Chamber decoration SUS430270接触片Contact piece 磷青铜273漏斗架装饰片Funnel bracket deco.不锈钢/PP/ABS 271壶盖锁片Lid lock piece274蒸汽挡板装饰片Steam baffle deco 272阴极接触片Cathode contact piece275杯手柄盖装饰片Carafe handle cover deco273阳极接触片Anode contact piece276开关面板装饰片Switch panel deco 274(上/下)装饰片(Upper/Lower) Decoration piece ABS 或不锈钢277控制面板装饰片Control panel deco 275前装饰片Front decoration ABS 或不锈钢278保险丝固定片Fuse holder 不锈钢276后装饰片Back decorationABS 或不锈钢279温控器固定片Thermostat holder 277按钮装饰片Button decoration不锈钢280传感器固定片Sensor fix plate不锈钢278顶盖装饰片Top cover decoration不锈钢281水箱挡片Water tank baffle 279底座装饰片Base decoration 282糖容器挡片Sugar container baffle 不锈钢/电解板280灯罩装饰片Lamp cover deco 283漏斗限位框Funnel limit frame 281壶盖装饰片Lid decoration 284透明镜装饰框Lens decorationframe282手柄座装饰片Handle seat decoration 285杯不锈钢外壳SUS jug housing 不锈钢283手柄盖装饰片Handle cover decoration286电池弹簧Battery spring 284旋钮弹片Knob spring plate287压缩弹簧Compressing spring不锈钢285静陶瓷片Static ceramic piece陶瓷288拉伸弹簧Tension spring 不锈钢286内散热片Internal heat sink 289(左/右)扭转弹簧(Left/Right)Wring spring 不锈钢287外散热片External heat sink290网格Mesh 不锈钢288制冷片Refrigerating piece291杯圈Jug ring 不锈钢289加强片Reinforcing piece 不锈钢292(上/下)保温板(Upper/Lower)Warming plate电解板/铝板290过滤片Filter piece 防锈铝或不锈钢293散热板Ventilation plate 电解板/铝板291感应片Sensing piece 冷轧板294发热管压条Heat element clamp 电解板292遮光片Light shield platePP 295主体装饰条Housingdecoration bar 293封气片Steam seal plateABC+PC 296水箱装饰条Tank decoration bar 294云母片Mica sheet云母板297发热管固定条Heat element fixing strip 295NTC 固定片NTC holder不锈钢298发热管固定架Heat element bracket 电解板296熔断器固定片Fuse holder 不锈钢299水箱装饰圈Water tank deco ring 297(左/右)接片(Left/Right) Connect plate 300顶盖装饰圈Top cover deco ring298防溅挡片Anti-splash plate301漏斗装饰圈Funnel deco ring 299过滤棉Filter cotton 302铁架固定圈Steel wire fix ring 铁丝300水闸Water gate POM 303云母板Mica plate MICA 301蒸汽闸Steam gate POM 304杯身橡胶圈Jug grip ring 硅胶/橡胶302胶塞Plunger 硅橡胶306电机脚Motor foot 硅胶/橡胶304NTC 密封塞 NTC Seal plug 307进水管Inlet tube 硅胶/PP/五金305(上/下)水尺密封塞(Upper/Lower) Water gauge seal 308出水管Outlet tube 硅胶/PP/五金306胶篮Plastic basket PP 309封口管Seal tube 307圆柱销Insert pin Q235A 钢,45钢310溢水管Overflow tube308旋转轴Rotate shaft PA311硅胶管Silicone tube 硅胶309壶盖转轴Lid shaft 312石英发热管Quartz heat element 310开关销轴Switch pin shaft 313水尺连接管Gauge connect tube 硅胶311铰链销轴Hinge pin shaft 314油封Oil seal硅胶312计时旋钮轴Timer knob shaft315水尺密封盖Gauge seal cap 硅胶313发热管Heat element316水箱密封圈Water tank seal ring 硅胶314蛇形发热管S shape heat element碳钢或不锈钢317连管密封圈Joint tube seal ring硅胶315马蹄形发热管U shape heat element铝管318灯罩密封圈Lamp cover ring 硅胶316双发热管Double heat element319灯圈密封圈Lamp loop ring 硅胶317压缩弹簧Compressing spring不锈钢320杯盖密封圈Jug top seal 硅胶318拉伸弹簧Tension spring 不锈钢321瓶胆密封圈Jug cavity seal ring 硅胶319壶盖扭簧Lid wring spring 322漏斗硅胶圈Funnel seal ring 硅胶320(左./右)扭转弹簧(Left/Right) Wring spring 不锈钢323LCD 密封圈LCD seal ring硅胶321弹性丝Spring wire65Mn 324磨粉密封圈Grinding seal ring 硅胶322勺Spoon 不锈钢或PP325防水密封圈Waterproof seal ring 硅胶323阻尼器Damper 326隔热密封圈Insulating seal ring 硅胶324计数器Counter 327弯管密封垫Outlet tube seal ring 硅胶325接触器Contactor PA66+30%GF328止漏密封圈Anti-drip seal ring 硅胶326净化器Purifier 329水管密封圈Water tube seal ring 硅胶327温控器Thermostat330水尺密封圈Gauge seal ring硅胶328温控连接器Thermostatic connector331排线密封圈Line wire seal ring 硅胶329电源转换器Power supply332阀芯密封圈Valve core seal ring 硅胶3303杯容器3-cup reservoir 防锈铝333杯口密封圈Jug mouth seal ring硅胶3316杯容器6-cup reservoir 防锈铝334电机密封圈Motor seal ring 硅胶332压力阀Pressure valve PC335内盖密封圈Inner cover seal ring 硅胶333安全阀Relief valve336PCB 盒密封圈PCB box seal ring 硅胶334蒸汽开关Steam switch 337液晶罩密封圈LCD cover seal ring 硅胶335圆形跷板开关Round rocker switch 338溢水管密封圈Spillover tube seal ring 硅胶336水尺组件Water gauge asm 339杯内盖密封圈Carafe lid inner ring 硅胶337引线组件Lead wire asm 340杯盖座密封圈Carafe lid base ring 硅胶338灯线组件Lamp wire asm 341蒸汽帽密封圈Steam cap seal ring 硅胶339灯板组件Lamp PCB asm 342升降杆密封圈Lift lever seal ring 硅胶340输出线组件Outlet line asm 343水箱挡片密封圈Water tank baffle ring 硅胶341PCB 组件PCB asm344控制面板密封圈Control panel seal 硅胶342电源线组件Power cord asm 345灯线护套密封圈Lamp jacket ring 硅胶343发热盘组件Heat plate asm 346水箱连接器密封圈Linker seal ring 硅胶344煲盖组件Body cover asm347浓度控制阀密封圈Strength control seal 硅胶345保温杯组件Warming cup asm 348(左/右)按键密封圈(L-/R-)Press key seal ring 硅胶346(左/右)按钮密(L-/R-)button seal电源转换器组件Power supply asm350保温板密封Warming platering硅胶348351活动门硅胶Move gate silicone硅胶349352隔热垫Thermal insulatemat350353密封垫Seal pad硅胶351354开关密封垫Switch seal pad硅胶352355LCD密封垫LCD seal pad硅胶353356按键密封垫Press key seal pad硅胶354357液晶罩密封垫LCD cover seal pad硅胶355358控制面板密封垫Control panel sealpad硅胶356359海绵垫Sponge pad海绵357360线路板硅胶垫PCB seal pad硅胶358361旅行杯Travel mup PP359362玻璃杯Carafe硼硅玻璃(Glass)360363陶瓷杯Ceramic jug陶瓷364不锈钢杯SUS jug不锈钢361365保温钢杯Vacuum jug362366桶Barrel363367咖啡桶Coffee bucket364368导水槽Water guidetrough365369咖啡导槽Coffee trough PP366370杯内胆Jug inside cavity PP367371玻璃瓶保温胆Jug cavity368372电机Motor369373面膜Membrane370374发热管Heat element371375发热煲Boiler372376发热保温片Warming piece373377磁铁圈Magnet ring374378顶盖扣件Top cover fastener硅胶375379手柄 Logo Handle Logo铝376380杯组件Jug Asm381刀片组件Blade Asm377382发热盘组件Heat plate Asm378383控制板组件Control PCB Asm379384电源板组件Power PCB Asm380385内配线组件Lead wire Asm381386不锈钢杯组件SUS jug Asm382387保温钢杯组件Vacuum jug Asm383384385386387388铸金。
行业标准规范英汉对照 通用零部件
行业标准规范英汉对照通用零部件.txt21春暖花会开！如果你曾经历过冬天，那么你就会有春色！如果你有着信念，那么春天一定会遥远；如果你正在付出，那么总有一天你会拥有花开满圆。
行业标准规范英汉对照通用零部件1 时间：2005-06-26 07:00 阿里巴巴－机械论坛J 机械通用零部件11 GB/T 2-1985 紧固件外螺纹零件的末端 Fasteners--Ends of parts with external thread2 GB/T 8-1988 方头螺栓 C级 Square head bolts--Product grade C3 GB/T 10-1988 沉头方颈螺栓 Flat countersunk square neck bolts4 GB/T 11-1988 沉头带榫螺栓 Flat countersunk nib bolts5 GB/T 12-1988 半圆头方颈螺栓 Cup head square neck bolts6 GB/T 13-1988 半圆头带榫螺栓 Cup head nib bolts7 GB/T 15-1988 大半圆头带榫螺栓 Cup head nib bolts with large head8 GB/T 22-1976 小六角头导颈螺栓 Bolts, small hexagon head with fit neck9 GB/T 23-1976 小六角头螺杆带孔螺栓 Bolts, small hexagon head with hole through the shank10 GB/T 24-1976 小六角头螺杆带孔导颈螺栓 Bolts, small hexagon head with fit neck and hole through the shank11 GB/T 25-1976 小六角头头部带孔螺栓 Bolts, small hexagon head with holes through the head12 GB/T 26-1976 小六角头头部带孔导颈螺栓 Bolts, small hexagon head with fit neck and holes through the head13 GB/T 27-1988 六角头铰制孔用螺栓 A和B级 Hexagon fit bolts--Product grade A andB14 GB/T 28-1988 六角头螺杆带孔铰制孔用螺栓 A和B级 Hexagon fit bolts with Split pin hole on shank--Product grade A and B15 GB/T 29.1-1988 六角头头部带槽螺栓A和B级Hexagon bolts with slot on head--Product grade A and B16 GB/T 29.2-1988 十字槽凹穴六角头螺栓Cross recessed hexagon bolts with indentation17 GB/T 31.1-1988 六角头螺杆带孔螺栓 A和B级 Hexagon bolts with split pin hole on shank--Product grade A and B18 GB/T 31.2-1988 六角头螺杆带孔螺栓细杆 B级 Hexagon bolts with split pin hole on shank--Reduced shank--Product grade B19 GB/T 31.3-1988 六角头螺杆带孔螺栓细牙 A和B级 Hexagon bolts with split pin hole on shank--Fine pitch thread--Product grade A and B20 GB/T 32.1-1988 六角头头部带孔螺栓 A和B级 Hexagon bolts with wire holes on head--Product grade A and B21 GB/T 32.2-1988 六角头头部带孔螺栓细杆 B级 Hexagon bolts with wire holes on head--Reduced shank--Product grade B22 GB/T 32.3-1988 六角头头部带孔螺栓细牙 A和B级 Hexagon bolts with wire holes on head--Fine pitch thread--Product grade A and B23 GB/T 35-1988 小方头螺栓 B级 Square head bolts with small head--Product grade B24 GB/T 37-1988 T型槽用螺栓 Bolts for T-Slot25 GB/T 38-1976 螺栓技术条件 Bolts--Technical requirements26 GB/T 39-1988 方螺母 C级 Square nuts--Product grade C27 GB/T 41-1986 1 型六角螺母 C 级 Hexagon nuts--Style 1--Product grad C28 GB/T 56-1988 六角厚螺母 Hexagon thick nuts29 GB/T 61-1976 螺母技术条件 Nuts--Technical requirements30 GB/T 62-1988 蝶形螺母 Wing nuts31 GB/T 63-1988 环形螺母 Lifting nuts32 GB/T 65-1985 开槽圆柱头螺钉 Slotted cheese head screws33 GB/T 67-1985 开槽盘头螺钉 Slotted pan head screws34 GB/T 68-1985 开槽沉头螺钉 Slotted countersunk head screws35 GB/T 69-1985 开槽半沉头螺钉 Slotted raised countersunk head screws36 GB/T 70-1985 内六角圆柱头螺钉 Hexagon socket cap head screws37 GB/T 71-1985 开槽锥端紧定螺钉 Slotted set screws with cone point38 GB/T 72-1988 开槽锥端定位螺钉 Slotted set screws with cone point39 GB/T 73-1985 开槽平端紧定螺钉 Slotted set screws with flat point40 GB/T 74-1985 开槽凹端紧定螺钉 Slotted set screws with cup point41 GB/T 75-1985 开槽长圆柱端紧定螺钉 Slotted set screws withlong dog point42 GB/T 77-1985 内六角平端紧定螺钉 Hexagon socket set screws with flat point43 GB/T 78-1985 内六角锥端紧定螺钉 Hexagon socket set screws with cone point44 GB/T 79-1985 内六角圆柱端紧定螺钉 Hexagon socket set screws with dog point45 GB/T 80-1985 内六角凹端紧定螺钉 Hexagon socket set screws with cup point46 GB/T 83-1988 方头长圆柱球面端紧定螺钉 Square set screws with long dog point and rounded end47 GB/T 84-1988 方头凹端紧定螺钉 Square set screws with cup point48 GB/T 85-1988 方头长圆柱端紧定螺钉 Square set screws with long dog point49 GB/T 86-1988 方头短圆柱锥端紧定螺钉 Square set screws with short dog point and cone end50 GB/T 89-1976 螺钉技术条件 Screws--Technical requirements51 GB/T 90-1985 紧固件验收检查、标志与包装 Acceptance inspection,marking and packaging of fasteners52 GB/T 91-1986 开口销 Split pins53 GB/T 93-1987 标准型弹簧垫圈 Single coil spring lock washers--Normal type54 GB/T 94.1-1987 弹性垫圈技术条件弹簧垫圈Specifications for spring washers--Single coil spring lock washers55 GB/T 94.2-1987 弹性垫圈技术条件齿形、锯齿锁紧垫圈 Specifications for spring washers--Toothed lock and serrated lock washers56 GB/T 94.3-1987 弹性垫圈技术条件鞍形、波形弹性垫圈 Specifications for spring washers--Curved and wave spring washers57 GB/T 95-1985 平垫圈-C级 Plain washers--Product grade C58 GB/T 272-1993 滚动轴承代号方法 Rolling bearing--Identification code59 GB/T 273.1-1987 滚动轴承圆锥滚子轴承外形尺寸方案 Rolling bearings Tapered roller bearings--Boundary dimensions60 GB/T 273.3-1988 滚动轴承向心轴承外形尺寸方案Rolling bearings Radial bearings—Boundary dimensions61 GB/T 274-1991 滚动轴承装配倒角极限 Rolling bearing chamfer dimension limits62 GB/T 275-1993 滚动轴承与轴和外壳的配合 Shaft and housing fits for rolling bearings63 GB/T 276-1994 滚动轴承深沟球轴承外形尺寸 Rolling bearings--Deep groove ball bearings--Boundary dimensions64 GB/T 280-1964 带毡封圈的单列向心球轴承结构型式和基本尺寸Rolling bearings--Single-row radial ball bearings withfelt seals--Types and basic dimensions 65 GB/T 281-1994 滚动轴承调心球轴承外形尺寸 Rolling bearings--Self-aligning ball bearings--Boundary dimensions66 GB/T 283-1994 滚动轴承圆柱滚子轴承外形尺寸 Rolling bearings--Cylindrical roller bearings—Boundary dimensions67 GB/T 285-1994 滚动轴承双列圆柱滚子轴承外形尺寸 Rolling bearings--Double row cylindrical roller bearings—Boundary dimensions68 GB/T 286-1964 双列向心球面滚子轴承结构型式和基本尺寸 Rolling bearings--Double -row radial spherical roller bearings--Types and basic dimensions69 GB/T 288-1994 滚动轴承调心滚子轴承外形尺寸 Rolling bearings--Self-aligning roller bearings—Boundary dimensions70 GB/T 289-1964 滚针轴承结构型式和基本尺寸 Needle roller bearings--Types and basic dimensions71 GB/T 291-1964 螺旋滚子轴承结构型式和基本尺寸 Rolling bearings with helically wound cylindrical rollers--Types and basic dimensions72 GB/T 292-1994 滚动轴承角接触球轴承外形尺寸 Rolling bearings--Angular contact ball bearings--Boundary dimensions73 GB/T 294-1994 滚动轴承三点和四点接触球轴承外形尺寸 Rolling bearings--Three point and four point contact ball bearings--Boundary dimensions74 GB/T 296-1994 滚动轴承双列角接触球轴承外形尺寸 Rolling bearings--Double row angular contact ball bearings--Boundary dimensions75 GB/T 297-1994 滚动轴承圆锥滚子轴承外形尺寸 Rolling bearings--Tapered roller bearings--Boundary dimensions76 GB/T 299-1995 滚动轴承双列圆锥滚子轴承外形尺寸 Rolling bearings--Metric double row tapered roller bearings--Boundary dimensions77 GB/T 300-1995 滚动轴承四列圆锥滚子轴承外形尺寸 Rolling bearings--Four row tapered roller bearings--Boundary dimensions78 GB/T 301-1995 滚动轴承推力球轴承外形尺寸 Rolling bearings--Thrust ball bearings--Boundary dimensions79 GB/T 304.1-1988 关节轴承分类 Spherical plain bearings Classification80 GB/T 304.2-1988 关节轴承代号方法 Spherical plain bearings Identification code81 GB/T 304.3-1990 关节轴承配合 Spherical plain bearings—Fits82 GB/T 304.9-1981 向心关节轴承技术条件 Spherical plain radial bearings, joint type--Technical requirements83 GB/T 304.10-1989 关节轴承公差 Spherical plain bearings—Tolerances84 GB/T 307.1-1994 滚动轴承向心轴承公差Rolling bearings--Radial bearings--Tolerances85 GB/T 307.2-1995 滚动轴承测量和检验的原则及方法 Rolling bearings--Measuring and gauging principles and methods86 GB/T 307.3-1996 滚动轴承通用技术规则 Rolling bearings--General technical regulations87 GB/T 307.4-1994 滚动轴承推力球轴承公差Rolling bearings--Thrust ball bearings--Tolerances88 GB/T 308-1989 滚动轴承钢球 Rolling bearings—Steel balls89 GB/T 309-1984 滚动轴承滚针 Rolling bearings--Needle rollers90 GB/T 794-1993 加强半圆头方颈螺栓 Strengthened cap head square neck bolts91 GB/T 798-1988 活节螺栓 Eye bolts92 GB/T 799-1988 地脚螺栓 Eyelet bolts93 GB/T 800-1988 沉头双榫螺栓 Flat countersunk double nib bolts94 GB/T 802-1988 组合式盖形螺母 Acorn nuts95 GB/T 804-1988 球面六角螺母 Hexagon nuts with raised face96 GB/T 805-1988 扣紧螺母 Tight nuts97 GB/T 806-1988 滚花高螺母 Knurled nut with collar98 GB/T 807-1988 滚花薄螺母 Knurled nuts99 GB/T 808-1988 小六角特扁细牙螺母 Small hexagon thin nuts-Fine pitch thread 100 GB/T 809-1988 嵌装圆螺母 Insert round nuts101 GB/T 810-1988 小圆螺母 Small round nuts102 GB/T 812-1988 圆螺母 Round nuts103 GB/T 815-1988 端面带孔圆螺母 Round nuts with drilled holes in one face104 GB/T 816-1988 侧面带孔圆螺母 Round nuts with set pin holes in side105 GB/T 817-1988 带槽圆螺母 Slotted round nuts106 GB/T 818-1985 十字槽盘头螺钉 Cross recessed pan head screws107 GB/T 819-1985 十字槽沉头螺钉 Cross recessed countersunk head screws108 GB/T 820-1985 十字槽半沉头螺钉 Cross recessed raised countersunk head screws 109 GB/T 821-1988 方头倒角端紧定螺钉 Square set screws with chamfered end110 GB/T 822-1988 十字槽圆柱头螺钉 Cross recessed cheese head serews111 GB/T 823-1988 十字槽小盘头螺钉 Cross recessed small pan head screws112 GB/T 824-1976 圆柱头内花键螺钉 Screws,fluted socket head113 GB/T 825-1988 吊环螺钉 Eyebolts114 GB/T 827-1986 标牌铆钉 Rivets for name plate115 GB/T 828-1988 开槽盘头定位螺钉 Slotted pan head set setscrews with dog point 116 GB/T 829-1988 开槽圆柱端定位螺钉 Slotted setscrews with dog point117 GB/T 830-1988 开槽圆柱头轴位螺钉 Slotted cheese head screws with shoulder 118 GB/T 831-1988 开槽无头轴位螺钉 Slotted shoulder screws119 GB/T 832-1988 开槽带孔球面圆柱头螺钉 Slotted capstan screws120 GB/T 833-1988 开槽大圆柱头螺钉 Slotted large cheese head screws121 GB/T 834-1988 滚花高头螺钉 Knurled thumb screws122 GB/T 835-1988 滚花平头螺钉 Knurled screws123 GB/T 836-1988 滚花小头螺钉 Knurled screws with small head124 GB/T 837-1988 开槽盘头不脱出螺钉 Slotted pan head screws with waisted shank 125 GB/T 838-1988 六角头不脱出螺钉 Hexagon screws with waisted shank126 GB/T 839-1988 滚花头不脱出螺钉 Knurled thumb screws with waisted shank127 GB/T 840-1988 塑料滚花头螺钉 Plastic diamond knurlhead screws128 GB/T 845-1985 十字槽盘头自攻螺钉 Cross recessed pan head tapping screws129 GB/T 846-1985 十字槽沉头自攻螺钉 Cross recessed countersunk head tapping screws 130 GB/T 847-1985 十字槽半沉头自攻螺钉 Cross recessed raised countersunk head tapping screws131 GB/T 848-1985 小垫圈--A级 Plain washers--Small series--Product grade A132 GB/T 849-1988 球面垫圈 Weshers with ball face133 GB/T 850-1988 锥面垫圈 Washers with cone face134 GB/T 851-1988 开口垫圈 Washers with split135 GB/T 852-1988 工字钢用方斜垫圈 Square taper washers for I section136 GB/T 853-1988 槽钢用方斜垫圈 Square taper washers for slot section137 GB/T 854-1988 单耳止动垫圈 Tab washers with long tab138 GB/T 855-1988 双耳止动垫圈 Tab washers with long tab and wing139 GB/T 856-1988 外舌止动垫圈 External tab washers140 GB/T 858-1988 圆螺母用止动垫圈 Tab washers for round nut141 GB/T 859-1987 轻型弹簧垫圈 Single coil spring lock washers,Light type142 GB/T 860-1987 鞍形弹性垫圈 Curved spring washers143 GB/T 861.1-1987 内齿锁紧垫圈 Lock washers internal teeth144 GB/T 861.2-1987 内锯齿锁紧垫圈 Serrated lock washers internal teeth145 GB/T 862.1-1987 外齿锁紧垫圈 Lock washers external teeth146 GB/T 862.2-1987 外锯齿锁紧垫圈 Serrated lock washers external teeth147 GB/T 863.1-1986 半圆头铆钉 (粗制) Round head rivets--Black148 GB/T 863.2-1986 小半圆头铆钉 (粗制) Round head rivets with small head--Black 149 GB/T 864-1986 平锥头铆钉 (粗制) Cone head rivets--Black150 GB/T 865-1986 沉头铆钉 (粗制) Countersunk head rivets-Black151 GB/T 866-1986 半沉头铆钉 (粗制) Oval countersunk head rivets--Black152 GB/T 867-1986 半圆头铆钉 Round head rivets153 GB/T 868-1986 平锥头铆钉 Cone head rivets154 GB/T 869-1986 沉头铆钉 Countersunk head rivets155 GB/T 870-1986 半沉头铆钉 Oval countersunk head rivets156 GB/T 871-1986 扁圆头铆钉 Flat round head rivets157 GB/T 872-1986 扁平头铆钉 Thin head rivets158 GB/T 873-1986 扁圆头半空心铆钉 Oval head semi-tubular rivets159 GB/T 874-1986 120°沉头半空心铆钉 120 degree countersunk head semi-tubular rivets160 GB/T 875-1986 偏平头半空心铆钉 Thin head semi-tubular rivet161 GB/T 876-1986 空心铆钉 Tubular rivets162 GB/T 877-1986 开尾圆锥销 Taper pins with split163 GB/T 878-1986 螺纹圆柱销 Parallel pins with external thread164 GB/T 879-1986 弹性圆柱销 Spring-type straight pins—Slotted165 GB/T 880-1986 带孔销 Pins with split pin hole166 GB/T 881-1986 螺尾锥销 Taper pins with external thread167 GB/T 882-1986 销轴 Clevis pins with head168 GB/T 883-1986 锥销锁紧挡圈 Lock rings with cone pin169 GB/T 884-1986 螺钉锁紧挡圈 Lock ring with screw170 GB/T 885-1986 带锁圈的螺钉锁紧挡圈 Lock rings with screw and circlip171 GB/T 886-1986 轴肩挡圈 Rings for shoulder172 GB/T 889-1986 1 型非金属嵌件六角锁紧螺母 Prevailing torque type hexagon nuts (with non-metallic insert),style 1173 GB/T 891-1986 螺钉紧固轴端挡圈 Lock rings at the end of shaft with screw174 GB/T 892-1986 螺栓紧固轴端挡圈 Lock rings at the end of shaft with bolt175 GB/T 893.1-1986 孔用弹性挡圈--A型 Circlips for holes--Type A176 GB/T 893.2-1986 孔用弹性挡圈--B型 Circlips for hole--Type B177 GB/T 894.1-1986 轴用弹性挡圈--A型 Circlips for shaft--Type A178 GB/T 894.2-1986 轴用弹性挡圈--B型 Circlips for shaft--Type B179 GB/T 895.1-1986 孔用钢丝挡圈 Roundwire snap rings for hole180 GB/T 895.2-1986 轴用钢丝挡圈 Roundwire snap rings for shaft181 GB/T 896-1986 开口挡圈 "E" rings182 GB/T 897-1988 双头螺柱 bm=1d Double end studs--bm=1d183 GB/T 898-1988 双头螺柱 bm=1.25d Double end studs bm=1.25d184 GB/T 899-1988 双头螺柱 bm=1.5d Double end studs bm=1.5d185 GB/T 900-1988 双头螺柱 bm=2d Double end studs bm=2d186 GB/T 901-1988 等长双头螺柱 B级 Double end studs (clamping type)--Product grade B187 GB/T 902.1-1989 手工焊用焊接螺柱 Weld studs for manual welding188 GB/T 902.2-1989 机动弧焊用焊接螺柱 Weld studs for arc welding189 GB/T 902.3-1989 储能焊用焊接螺柱 Weld studs for capacitor discharge welding 190 GB/T 921-1986 钢丝锁圈 Round wire circlips191 GB/T 922-1986 木螺钉技术条件 Specifications for wood screws192 GB/T 923-1988 盖形螺母 Acorn nuts193 GB/T 925-1988 轻型六角自锁螺母 Self-locking nuts,hexagon light194 GB/T 927-1988 球面六角自锁螺母 Self-locking nuts,hexagon sphere195 GB/T 929-1988 单耳托板自锁螺母 Self-locking nuts,singlelug, anchor196 GB/T 930-1988 双耳托板自锁螺母 Self-locking nuts,twolug, anchor197 GB/T 931-1988 角形托板自锁螺母 Self-locking nuts,angle, anchor198 GB/T 932-1988 气密单耳托板自锁螺母Self-locking nuts,singlelug, anchor, sealing,199 GB/T 933-1988 气密双耳托板自锁螺母 Self-locking nuts,twolug, anchor, sealing 200 GB/T 937-1988 成组游动托板自锁螺母 Self-locking nuts, anchor, floating,Gang channel201 GB/T 938-1988 游动自锁螺母 Self-locking nuts, floating202 GB/T 939-1988 单耳托板自锁螺母保护罩 Boots for self-locking nuts, singlelug, anchor203 GB/T 940-1988 双耳托板自锁螺母保护罩 Boots for self-locking nuts,twolug, anchor204 GB/T 941-1988 角形托板自锁螺母保护罩 Boots for self-locking nuts,angle, anchor 205 GB/T 943-1988 自锁螺母技术条件 Procurement specification for self-locking nuts 206 GB/T 945-1976 十字槽球面中柱头螺钉 Screws,cross recessed,thin raised cheese head207 GB/T 946-1988 开槽球面圆柱头轴位螺钉 Slotted raised cheese head with shoulder 208 GB/T 947-1988 开槽球面大圆柱头螺钉 Slotted large raised cheese head screws 209 GB/T 948-1988 开槽沉头不脱出螺钉 Slotted countersunk head screws with waisted shank210 GB/T 949-1988 开槽半沉头不脱出螺钉 Slotted raised countersunk head screws with waisted shank211 GB/T 950-1986 十字槽圆头木螺钉 Cross recessed round head wood screws212 GB/T 951-1986 十字槽沉头木螺钉 Cross recessed countersunk head wood screws 213 GB/T 952-1986 十字槽半沉头木螺钉 Cross recessed raised countersunk head wood screws214 GB/T 953-1988 等长双头螺柱 C级 Double end studs (clamping type)--Product grade C215 GB/T 954-1986 120°沉头铆钉 120°degree countersunk head rivets216 GB/T 955-1987 波形弹性垫圈 Wave spring washers217 GB/T 956.1-1987 锥形锁紧垫圈 Countersunk external toothed lock washers218 GB/T 956.2-1987 锥形锯齿锁紧垫圈 Countersunk serrated external toothed lock washers219 GB/T 959.1-1986 挡圈技术条件--弹性挡圈 Specifications for ring—Circlips220 GB/T 959.2-1986 挡圈技术条件--钢丝挡圈 Specifications for ring—Round wire snap rings221 GB/T 959.3-1986 挡圈技术条件--切制挡圈 Specifications for ring—Cutting rings 222 GB/T 960-1986 夹紧挡圈 Grip rings223 GB/T 961-1988 单耳托板自锁螺母垫片 Spacers for self-locking nuts,singlelug, anchor224 GB/T 962-1988 双耳托板自锁螺母垫片 Spacers for self-locking nuts,twolug, anchor 225 GB/T 963-1988 角形托板自锁螺母垫片 Spacers for self-locking nuts,angle, anchor 226 GB/T 973-1976 十字槽扁圆头螺钉 Screws,cross recessed,oval head227 GB/T 974-1976 十字槽120°半沉头螺钉Screws,cross recessed,120°raised countersunk head228 GB/T 975-1986 管状铆钉 Pipe type rivets229 GB/T 1007-1976 小六角较扁螺母 Small hexagon medium thin nuts230 GB/T 1009-1978 螺母专用技术条件 Specified specifications for nuts231 GB/T 1011-1986 大扁圆头铆钉 Truss head rivets232 GB/T 1012-1986 120°半沉头铆钉 120°degree oval countersunk rivets233 GB/T 1013-1986 平锥头半空心铆钉 Cone head semi-tubuler rivets234 GB/T 1014-1986 大扁圆头半空心铆钉 Truss head semi-tubuar rivets235 GB/T 1015-1986 沉头半空心铆钉 Countersunk head semi-tublar rivets236 GB/T 1016-1986 无头铆钉 Headless rivets237 GB/T 1017-1978 铆钉专用技术条件 Specified specifications for rivets238 GB/T 1021-1976 角形垂直单耳止动垫圈 Lock washers with angular upturn tabperpendicular to the lug239 GB/T 1022-1976 角形单耳止动垫圈 Lock washers with angular upturn tab in line to the lug240 GB/T 1023-1976 角形垂直外舌止动垫圈 Lock washers with angular upturn tab perpendicular to the external tab241 GB/T 1024-1976 角形外舌止动垫圈 Lock washers with angular upturn tab in line to the external tab242 GB/T 1030-1988 内球面垫圈 Inner sphere washers243 GB/T 1047-1995 管道元件的公称通径 Nominal size for pipe components244 GB/T 1048-1990 管道元件公称压力 Nominal pressure for pipe components245 GB/T 1095-1979 平键键和键槽的剖面尺寸 Parallel keys--Dimensions of cross sections and keyways246 GB/T 1096-1979 普通平键型式尺寸 Plain parallel keys--Types and dimensions 247 GB/T 1097-1979 导向平键型式尺寸 Feather keys--Types and dimensions248 GB/T 1098-1979 半圆键键和键槽的剖面尺寸Semi-circular (Woodruff) keys--Dimensions of cross sections and keyways249 GB/T 1099-1979 半圆键型式尺寸 Woodruff keys--Types and dimensions250 GB/T 1144-1987 矩形花键尺寸、公差和检验 Straight-sided spline—Dimensions tolerances and verification251 GB/T 1168-1976 螺柱技术条件 Studs--Technical requirements252 GB/T 1228-1991 钢结构用高强度大六角头螺栓 High strength bolts with large hexagon head for steel structures253 GB/T 1229-1991 钢结构用高强度大六角螺母 High strength large hexagon nuts for steel structures254 GB/T 1230-1991 钢结构用高强度垫圈High strength plain washers for steel structures255 GB/T 1231-1991 钢结构用高强度大六角头螺拴、大六角螺母、垫圈技术条件Specifications of high strength bolts with large hexa-gon head, large hexagon nuts, plain washers for steel structures256 GB/T 1237-1988 紧固件的标记方法 Designation system for fasteners257 GB/T 1337-1988 六角自锁螺母 Self-locking nuts,hexagon258 GB/T 1338-1988 小六角扁自锁螺母 Self-locking nuts,reduced hexagon oblate 259 GB/T 1339-1988 小六角自锁螺母 Self-locking nuts,reduced hexagon260 GB/T 1340-1988 成组游动托板自锁螺母支架 Supports for self-locking nuts,anchor floating,Gang channel261 GB/T 1356-1988 淅开线圆柱齿轮基本齿廓 Basic rack tooth profile of involute cylindrical gears262 GB/T 1357-1987 渐开线圆柱齿轮模数 Modules of involute cyindrical gears263 GB/T 1563-1979 楔键键和键槽的剖面尺寸 Taper keys--Cross section dimensions of keys and keyways264 GB/T 1564-1979 普通楔键型式尺寸Taper keys for general use--Types and dimensions265 GB/T 1565-1979 钩头楔键型式尺寸 Gib-head taper keys--Types and dimensions 266 GB/T 1566-1979 薄型平键键和键槽的剖面尺寸 Thin flat keys--Cross sectiondimensions and keyways267 GB/T 1567-1979 薄型平键型式尺寸 Thin flat keys--Types and dimensions268 GB/T 1840-1989 圆弧圆柱齿轮模数 Modules of cylindrical gear with circular arc profiles269 GB/T 1974-1980 切向键及其键槽 Tangential keys and keyways270 GB/T 2362-1990 小模数渐开线圆柱齿轮基本齿廓 Basic rack tooth profile of fine-pitch involute cylindrical gears271 GB/T 2363-1990 小模数渐开线圆柱齿轮精度Accuracy of fine-pitch involute cylindrical gears272 GB/T 2509-1981 滑动轴承铜合金整体轴套形式、尺寸与公差 Copper alloy integrated shaft sleeves for plain bearings--Types, dimensions and tolerances273 GB/T 2510-1981 滑动轴承铜合金带挡边整体轴套形式、尺寸与公差 Copper alloy integrated shaft sleeves for plain bearings with gears--Types, dimensions and tolerances274 GB/T 2511-1981 滑动轴承铜合金整体轴套技术条件 Copper alloy integrated shaft sleeves--Technical requirements275 GB/T 2555-1981 一般用途管法兰连接尺寸 Pipe flange connectors for ordinary use--Mounting dimensions276 GB/T 2556-1981 一般用途管法兰密封面形状和尺寸 Pipe flanges for ordinary use--Sealing surfaces--Forms and dimensions277 GB/T 2672-1986 内六角花形盘头螺钉 Hexagon lobular socket pan head screws278 GB/T 2673-1986 内六角花形沉头螺钉 Hexagon lobular socket countersunk head screws279 GB/T 2674-1986 内六角花形半沉头螺钉 Hexagon lobular socket raised countersunk head screws280 GB/T 2685-1981 滑动轴承粉末冶金筒形轴承型式、尺寸与公差 Powder metallurgy plain bearing--Cylindrical type--Types, dimensions and tolerances281 GB/T 2686-1981 滑动轴承粉末冶金带挡边筒形轴承型式、尺寸与公差Powder metallurgy plain bearing--Rimed cylindrical type--Types, dimensions and tolerances 282 GB/T 2687-1981 滑动轴承粉末冶金球形轴承型式、尺寸与公差 Powder metallurgy plain bearing--Spherical type--Types, dimensions and tolerances283 GB/T 2688-1981 滑动轴承粉末冶金轴承技术条件Powder metallurgy plain bearing--Technical requirements284 GB/T 2821-1992 齿轮几何要素代号 Symbols for gear geometrical data285 GB/T 2889-1994 滑动轴承术语Plain bearings--Terms, definitions and classification286 GB/T 3098.1-1982 紧固件机械性能螺栓、螺钉和螺柱 Mechanical properties of fasteners--Bolts, screws and studs287 GB/T 3098.2-1982 紧固件机械性能螺母 Mechanical properties of fasteners--Nuts 288 GB/T 3098.3-1982 紧固件机械性能紧定螺钉Mechanical properties of fasteners--Set screws289 GB/T 3098.4-1986 紧固件机械性能--细牙螺母Mechanical properties of fasteners--Nuts with fine pitch thread290 GB/T 3098.5-1985 紧固件机械性能自攻螺钉Mechanical properties offasteners--Tapping screws291 GB/T 3098.6-1986 紧固件机械性能不锈钢螺栓, 螺钉, 螺柱和螺母 Mechanical properties of fasteners--Stainless steel bolts,screws, studs and nuts292 GB/T 3098.7-1986 紧固件机械性能自攻锁紧螺钉粗牙普通螺纹系列 Mechanical properties of fasteners--Thread forming screws--Metric coarse thread series293 GB/T 3098.8-1992 紧固件机械性能耐热用螺纹连接副 Mechanical properties of fasteners--Components for bolted connections made mainly from materials with a high temperature strength294 GB/T 3098.9-1993 紧固件机械性能有效力矩型钢六角锁紧螺母 Mechanical properties of fasteners--Prevailing torque type steel hexagon nuts295 GB/T 3098.10-1993 紧固件机械性能有色金属制造的螺栓、螺钉、螺柱和螺母Mechanical properties of fasteners--Bolts, screws, studs and nuts made of non-ferrous metals296 GB/T 3098.11-1995 紧固件机械性能自钻自攻螺钉Mechanical properties of fasteners--Self-drilling tapping screws297 GB/T 3098.13-1996 紧固件机械性能螺栓与螺钉的扭矩试验和破坏扭矩公称直径1~10mm Mechanical properties of fasteners--Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm298 GB/T 3098.12-1996 紧固件机械性能螺母锥形保证载荷试验 Mechanical properties of fasteners--Cone proof load test on nuts299 GB/T 3099-1982 螺栓、螺钉、螺母及附件名词术语Bolts, screws, nuts and accessories--Terminology and nomenclature300 GB/T 3103.1-1982 紧固件公差螺栓、螺钉和螺母 Tolerances for fasteners--Bolts, screws and nuts行业标准规范英汉对照通用零部件1 时间：2005-06-26 07:00 阿里巴巴－机械论坛301 GB/T 3103.2-1982 紧固件公差用于精密机械的螺栓、螺钉和螺母 Tolerances for fasteners--Bolts, screws and nuts for fine mechanics302 GB/T 3103.3-1982 紧固件公差平垫圈 Tolerances for fasteners--Washers303 GB/T 3103.4-1992 紧固件公差耐热用螺纹连接副Tolerances for fasteners--Components for bolted connections made mainly from materials with a high temperature strength304 GB/T 3104-1982 紧固件六角产品的对边宽度 Fasteners--Widths across flats of hexagon products305 GB/T 3105-1982 螺栓和螺钉的头下圆角半径 Radii under the head of bolts and screws 306 GB/T 3106-1982 螺栓、螺钉和螺柱的公称长度和普通螺栓的螺纹长度 Bolts, screws and studs--Nominal lengths, and thread lengths for general purpose bolts307 GB/T 3162-1991 滑动轴承薄壁轴瓦尺寸、结构要素与公差Plain bearings—Thin-walled bearing shells—Dimensions, structure elements and tolerances 308 GB/T 3287-1982 可锻铸铁管路连接件技术条件 Technical requirements of malleable cast iron pipe fittings309 GB/T 3288-1982 可锻铸铁管路连接件验收规则 Delivery requirements of malleablecast iron pipe fittings310 GB/T 3289.1-1982 可锻铸铁管路连接件型式尺寸管件结构尺寸表 Malleable cast iron pipe fittings--Type size--Dimensions list of pipe fittings structure311 GB/T 3289.2-1982 可锻铸铁管路连接件型式尺寸弯头内外丝弯头 Malleable cast iron pipe fittings--Type size--Elbows male and female elbows312 GB/T 3289.3-1982 可锻铸铁管路连接件型式尺寸 45°弯头 45°内外丝弯头 Malleable cast iron pipe fittings--Type size--Elbows 45°, male and female elbows 45°313 GB/T 3289.4-1982 可锻铸铁管路连接件型式尺寸异径弯头 Malleable cast iron pipe fittings--Type size--Reducing elbows314 GB/T 3289.5-1982 可锻铸铁管路连接件型式尺寸异径内外丝弯头 Malleable cast iron pipe fittings--Type size--Male and female reducing elbows315 GB/T 3289.6-1982 可锻铸铁管路连接件型式尺寸侧孔弯头 Malleable cast iron pipe fittings--Type size--Side outlet elbows316 GB/T 3289.7-1982 可锻铸铁管路连接件型式尺寸月弯内外丝月弯外丝月弯Malleable cast iron pipe fittings--Type size--Return bends, male and female return bends, thread return bends317 GB/T 3289.8-1982 可锻铸铁管路连接件型式尺寸 45°月弯45°内外丝月弯45°外丝月弯 Malleable cast iron pipe fittings--Type size--Long sweep bends 45°，male and female long sweep bends 45°,male long sweep bends 45°318 GB/T 3289.9-1982 可锻铸铁管路连接件型式尺寸 U型弯头 Malleable cast iron pipe fittings--Type size--U-Elbows(return bends)319 GB/T 3289.10-1982 可锻铸铁管路连接件型式尺寸三通内外丝三通 Malleable cast iron pipe fittings--Type size--Tees, male and female tees320 GB/T 3289.11-1982 可锻铸铁管路连接件型式尺寸异径内外丝三通 Malleable cast iron pipe fittings--Type size--Male and female reducing tees321 GB/T 3289.12-1982 可锻铸铁管路连接件型式尺寸中大异径三通 Malleable cast iron pipe fittings--Type size--Medium-large reducing tees [tees(increasing on the branch)]322 GB/T 3289.13-1982 可锻铸铁管路连接件型式尺寸侧大异径三通 Malleable cast iron pipe fittings--Type size--Lateral-large reducing tees323 GB/T 3289.14-1982 可锻铸铁管路连接件型式尺寸中小异径三通 Malleable cast iron pipe fittings--Type size--Medium-less reducing tees324 GB/T 3289.15-1982 可锻铸铁管路连接件型式尺寸侧小异径三通 Malleable cast iron pipe fittings--Type size--Lateral-less reducing tees325 GB/T 3289.16-1982 可锻铸铁管路连接件型式尺寸中小偏心异径三通 Malleable cast iron pipe fittings--Type size--Medium-less eccentric reducing tees326 GB/T 3289.17-1982 可锻铸铁管路连接件型式尺寸 45°三通 Y型三通 Malleable cast iron pipe fittings--Type size--Tees45°, Y pieces(tees)327 GB/T 3289.18-1982 可锻铸铁管路连接件型式尺寸 Y型异径三通 Malleable cast iron pipe fittings--Type size--Y Piece reducing(tees)328 GB/T 3289.19-1982 可锻铸铁管路连接件型式尺寸侧孔三通 Malleable cast iron pipe fittings--Type size--Side outlet tees329 GB/T 3289.20-1982 可锻铸铁管路连接件型式尺寸四通 Malleable cast iron pipe fittings--Type size--Crosses330 GB/T 3289.21-1982 可锻铸铁管路连接件型式尺寸异径四通 Malleable cast iron pipe fittings--Type size--Reducing crosses331 GB/T 3289.22-1982 可锻铸铁管路连接件型式尺寸外接头内外丝接头 Malleable cast iron pipe fittings--Type size--Male joints(sockets), male and female joints (sockets)332 GB/T 3289.23-1982 可锻铸铁管路连接件型式尺寸无方内接头 Malleable cast iron pipe fittings--Type size--No-square inner joint (nipples)333 GB/T 3289.24-1982 可锻铸铁管路连接件型式尺寸异径外接头 Malleable cast iron pipe fittings--Type size--Reducing male joints (sockets)334 GB/T 3289.25-1982 可锻铸铁管路连接件型式尺寸偏心异径外接头 Malleable cast iron pipe fittings--Type size--Eccentric reducing male joints (sockets)335 GB/T 3289.26-1982 可锻铸铁管路连接件型式尺寸内接头 Malleable cast iron pipe fittings--Type size--Inner joints (nipples hexagon)336 GB/T 3289.27-1982 可锻铸铁管路连接件型式尺寸异径内接头 Malleable cast iron pipe fittings--Type size--Reducing inner joints(nipples hexagon)337 GB/T 3289.28-1982 可锻铸铁管路连接件型式尺寸内外螺丝 Malleable cast iron pipe fittings--Type size--Male and female screws (bushings)338 GB/T 3289.29-1982 可锻铸铁管路连接件型式尺寸通丝外接头 Malleable cast iron pipe fittings--Type size--Through thread male joint (sockets)339 GB/T 3289.30-1982 可锻铸铁管路连接件型式尺寸锁紧螺母 Malleable cast iron pipe fittings--Type size--Backnuts340 GB/T 3289.31-1982 可锻铸铁管路连接件型式尺寸外方管堵 Malleable cast iron pipe fittings--Type size--Outer-square plugs行业标准规范英汉对照-通用零部件2 时间：2005-06-20 09:44 阿里巴巴－机械论坛341 GB/T 3289.32-1982 可锻铸铁管路连接件型式尺寸带边外方管堵 Malleable cast iron pipe fittings--Type size--Outer-square beaded plugs342 GB/T 3289.33-1982 可锻铸铁管路连接件型式尺寸内方管堵 Malleable cast iron pipe fittings--Type size--Inner-square plugs343 GB/T 3289.34-1982 可锻铸铁管路连接件型式尺寸管帽 Malleable cast iron pipe fittings--Type size--Tube caps (caps plugs)344 GB/T 3289.35-1982 可锻铸铁管路连接件型式尺寸活接弯头内外丝活接弯头Malleable cast iron pipe fittings--Type size--Union elbows, male and female union elbows345 GB/T 3289.36-1982 可锻铸铁管路连接件型式尺寸活接三通 Malleable cast iron pipe fittings--Type size--Union tees346 GB/T 3289.37-1982 可锻铸铁管路连接件型式尺寸平形活接头 Malleable cast iron pipe fittings--Type size--Parallel unions347 GB/T 3289.38-1982 可锻铸铁管路连接件型式尺寸锥形活接头 Malleable cast iron pipe fittings--Type size--Taper unions348 GB/T 3289.39-1982 可锻铸铁管路连接件型式尺寸平形活接头垫圈 Malleable cast。
聚乙烯四氟板
聚四氟乙烯板目录1概述2分类3用途4材料优点5外观标准6技术参数7化学式1其在500摄氏度左右的完全热分解产物有四氟乙烯、六氟丙烯和八氟环丁烷，这些产物在高温时会分解出高腐蚀性的含氟气体。
2分类聚四氟乙烯板(也叫四氟板,铁氟龙板,特氟龙板)分模压和车削两种，模压板是由聚四氟乙烯树脂在常温下用模压法成型，再经烧结、冷却而制成。
聚四氟乙烯车削板由聚四氟乙烯树脂经压坯、烧结、旋切而成。
其制品用途广，具有极为优越的综合性能：耐高低温（-192℃-260℃)、耐腐蚀（强酸、强碱、王水等）、耐气候、高绝缘、高润滑、不粘附、无毒害等优良特性。
[1]3用途目前，各类聚四氟乙烯制品已在化工、机械、电子、电器、军工、航天、环保和桥梁等国民经济领域中起到了举足轻重的作用。
四氟乙烯板适用于-180℃~+250℃温度下，主要用作电器绝缘材料及接触腐蚀介质的衬里、支承滑块、道轨密封件及润滑材料，富柜家具把它用于轻工业中，广泛应用于化工、医药、染料业容器、贮槽、反应塔釜、大型管道的防腐衬里材料；航空、军事等重工业领域；机械、建筑、交通桥梁滑块、导轨；印染、轻工、纺织业的防粘材料等．聚四氟乙烯板4材料优点耐高温——使用工作温度达250℃。
耐低温——具有良好的机械韧性；即使温度下降到-196℃，也可保持5%的伸长率。
耐腐蚀——对大多数化学药品和溶剂，表现出惰性、能耐强酸强碱、水和各种有机溶剂。
耐气候——有塑料中最佳的老化寿命。
高润滑——是固体材料中摩擦系数最低者。
不粘附——是固体材料中最小的表面张力，不粘附任何物质，力学性能它的摩擦系数极小，仅为聚乙烯的1/5，这是全氟碳表面的重要特征。
又由于氟-碳链分子间作用力极低，所以聚四氟乙烯具有不粘性。
无毒害——具有生理惰性，作为人工血管和脏器长期植入体内无不良反应。
电性能聚四氟乙烯在较宽频率范围内的介电常数和介电损耗都很低，而且击穿电压、体积电阻率和耐电弧性都较高。
耐辐射性能聚四氟乙烯的耐辐射性能较差（104拉德），受高能辐射后引起降解，高分子的电性能和力学性能均明显下降。
DIN74324-1尼龙管_1996修订-简译中文
密 度 按 DIN73378：1996－02 中 表 7 × － 溶 化 温 度 按 DIN73378：1996－02 中 表 7 × － 可 萃 取 的 组 分 按 DIN73378：1996－02 中 的 5.2.5 × － 规 格 类 别 按 DIN73378：1996－02 中 的 5.3 × × 相 对 应 力 强 度 按 DIN73378：1996－02 中 的 5.4.3 × × 冲 击 强 度 按 DIN73378：1996－02 中 的 5.4.4 × × 紫 外 线 耐 久 性 按 4.2.2.1 × － 热 稳 定 性 按 4.2.2.2 × － 密 封 性 按 4.2.2.3 × × 1) 除 弹 性 模 数 外， 试 验 A 为 产 品 的 常 规 检 验，按 DIN16773－2 用 注 塑 法 制 作 试 样 时，在 干 燥 条 件 下 弹 性 模 数 将 作 为 刚 性 度 量。 2) 试 验 B 应 视 为 连 续 生 产 过 程 中 的 产 品 质 量 检 验。 4.4 试 验 方 法 4.4.1 试 验 按 DIN73378
DIN74324
本 标 准 属 于 FAKRA 汽 车 标 准 委 员 会 的 SPA22/2/1R“ 聚 酰 胺 管 子” 工 作 组 编 写 的。
附 录 A 和 附 录 B 是 消 息 报 导。
更 改：
对 照 1991 年 10 月 出 版 资 料 作 了 以 下 变 动：
a) 采 用 了 新 材 料 管 子：PA12－HIPHL、 PA11－PHLY、 和 PA12－PHLY， 参 见 表 2 和 表 6 。
0.90 × × 60
中德及国际标准螺丝标准对应表
序号中文品名德国标准DIN中国标准GB国际标准ISO英文品名1自攻自钻螺钉多种头型DIN7504GB15856.1-4Self-drilling tapping screws2平垫DIN125-A GB97.1-85ISO7089Plain washers3平垫（带倒角）DIN125-B GB97.2-85ISO7090Mediun washers4平垫DIN126ISO7091Plain washers5重型弹垫DIN127-A GB7244Spring lock washers,tang ends 6标准弹垫DIN127-B GB93-87Spring lock washers,square ends 7内六角扳手DIN911ISO2936Socket wrenches8内六角圆柱头螺钉DIN912GB70-85ISO4762Hexagon socket cap screws9内六角平端紧定螺钉DIN913GB77-85ISO4026Hexagon socket set screws with falt point10内六角尖端紧定螺钉DIN914GB78-85ISO4027Hexagon socket set screws with cone point11内六角圆柱端紧定螺钉DIN915GB79-85ISO4028Hexagon socket set screws with dog point12内六角凹端紧定螺钉DIN916GB80-85ISO4029Hexagon socket set screws with cup point13六角头螺栓）（半牙）DIN931GB5782-86ISO4014Hexagon head screws 14六角头螺栓（全牙）DIN933GB5783-86ISO4017Hexagon head screws15开槽沉头螺钉DIN963GB68-85ISO2009Slottedｃｏｕｎｔersund head screws16开槽半沉头螺钉DIN964GB69-85ISO2010Slotted raisedｃｏｕｎｔersunk oval head screws17十字槽沉头螺钉DIN965GB819-85ISO7046Cross recessedｃｏｕｎｔersunk head screws18十字槽半沉头螺钉DIN966GB820-85ISO7047Cross recessed raised19十字槽盘头自攻螺攻DIN7981GB845-85ISO7049Pan head tapping screws with cross recessed20十字槽沉头自攻螺攻DIN7982GB846-85ISO7050ｃｏｕｎｔersunk flat head tapping screws with cross21十字槽半沉头自攻螺攻DIN7983GB847-86ISO7051Raisedｃｏｕｎｔersunk oval head tapping screws with cross22开槽盘头自攻螺钉DIN7971GB5282-85ISO1481Pan head tapping screws with slot23开槽沉头自攻螺钉DIN7972GB5283-85ISO1482ｃｏｕｎｔersunk flat head tapping screws with slot24开槽半沉头自攻螺钉DIN7973GB5284-85ISO1483Raised sountersunk oval head tapping screws with slot25六角头自攻螺钉DIN7976GB5285-85ISO1479Hexagon tapping screws26十字槽盘头螺钉DIN7985GB818-85ISO7045Pan head screws with cross recessed27内六角沉头螺钉DIN7991ISO10642Hexagon socket coutersunk head screws28六角头尼龙锁紧螺母DIN982GB812-88ISO2982Prevailing rorque type hexagon nuts,heavy type,with nylon29六角头薄型尼龙锁紧螺母DIN985GB889.1-86ISO7040Prevalling torque type hoxagon nuts,heavy type,with nylon30六角盖型尼龙锁紧螺母DIN986GB6172.2-86ISO10511Preailling torque typedomed capnuts with nylonｉｎｓｅｒｔ中德螺丝标准对应表31六角头螺母（1型）DIN934GB6170-86ISO4032Hexagon full nuts 32细牙六角头螺母（1型）DIN934GB6171-86ISO8673Hexagon full nuts 33六角头薄螺母DIN936GB6172.1-86ISO4035Hexagon thin nuts 34六角薄螺母DIN439GB6172-86ISO4035Hexagon thin nuts35开槽半沉头木螺钉DIN95GB101Slotted raised csk head wood screws36开槽半圆头木螺钉DIN96GB99Slotted round head wood screws37开槽沉头木螺钉DIN97GB100Slottedｃｏｕｎｔersunk head wood screws38鞍形弹垫DIN128-A GB7245-87Single coil spring lock washers 39弹簧止动垫圈DIN137-A Curved spring washers40波形弹垫DIN137-B GB955Wave spring washers41T型方颈螺栓DIN186GB37-88T-head blots with square neck 42T型双接头螺栓DIN188T-head bolts with double nip43螺纹圆锥销DIN258ISO8737Taper pins with threaded end44T型头螺栓DIN261T-head bolts45蝶型螺母（美制）DIN315AF Wing nuts America form46蝶型螺母（德制）DIN315DF GB62-88Wing nuts germany form47蝶型螺母（美制）DIN316AF Wing screws America form48蝶型螺母（德制）DIN317DF Wing screws germany form49圆球型盖型螺母DIN319Ball knobs50开槽带孔球面圆柱头蚴钉DIN404GB832-88Slotted capstan screws51开槽长圆柱端紧定螺钉DIN417GB75-85ISO7435Slotted set srews with full dog point52开槽平端紧定螺钉（半牙）DIN427GB73-85ISO2342Slotted set srews with chamfered end53小六角特薄细牙螺母DIN431GB808-88Pip nuts with thread54外舌止动垫圈DIN432GB856-88External tap55小垫圈(用于圆柱头螺钉)DIN433GB848-95ISO7092Washers for cheese head screws 56方斜垫圈（U型）DIN434GB852-88Square taper washers for57方斜垫圈（I型）DIN435GB852-88Square taper washers for58方垫圈DIN436Square washers59开槽凹端紧定螺钉DIN438GB74-85ISO7436Slotted set with cup point60细牙六角薄螺母DIN439GB6173-86ISO8675Hexagon thin nuts61木螺钉专用垫圈DIN440ISO7094Rounds washers for wood constructions62密封帽DIN443Sealing caps,push-in type63活节螺栓B型DIN444GB798-88Eye bolts form B64内舌止动垫圈DIN462Internal tab washers65双耳止动垫圈DIN463GB855-88Washers with two taps66滚花高头螺钉DIN464GB834-88Knurled thumb screws with collar67开槽滚花高头螺钉DIN465Slotted knurled thumb screws with collar68滚花高螺母DIN466GB806-88Knurled thumb nuts with collar 69滚花薄螺母DIN467GB807-88Knurled thumb thin nuts70锁紧垫圈DIN470Sealing washers71轴用弹性垫圈DIN471GB893-86Retaining rings for shafts(external),circlips72孔用弹性垫圈DIN472GB893.86Retaining rings for bores(internal),circlips73方头带垫螺栓DIN478Square head bolts with collar74方头圆柱底端螺栓DIN479Square head bolts with half dog point75方头带垫关圆底端螺栓DIN480Square head bolts with collar,half dog point76T型槽螺母DIN508ISO299T-slot nuts77单头螺柱DIN525Single end studs 78地脚螺栓DIN529GB799-88Masonry bolts79带槽圆螺母DIN546GB817-76Slotted round nuts80端面带孔圆螺母DIN547GB815-88Round nuts with drilled holes in one face81开槽平端紧定螺钉DIN551GB73-85ISO4776Slotted set screws with flat point82开槽锥端紧定螺钉DIN553GB71-85ISO7434Slotted set screws with cone point83六角螺母DIN555ISO4034Hexagon nuts 84方螺母-C DIN557GB39-88Square nuts85六角头螺钉DIN558ISO4018Hexagon screws86六角头圆柱端紧定螺钉DIN561Hexagon set screws with full dog point87薄型方螺母-B DIN562Square nuts without bevel 88六角头木螺钉DIN571GB102-86Hexgon head wood screw89吊环螺钉DIN580GB825-76ISO3266Lifting eye bolts90吊环螺母DIN582Lifting eye nuts91六角头螺栓DIN601ISO4016Hexagon blots92大半圆头方颈螺栓（马车螺栓）DIN603GB14-88ISO8677Mushroom head square neckbolts(carriage bolts)93沉头带插销马车螺栓DIN604Flatｃｏｕｎｔersunk nib bolts94沉头长方颈马车螺栓DIN605Flatｃｏｕｎｔersunk long squareneck bolts95半圆头带插销马车螺栓DIN607Cup head nib bolts96沉头短方颈马车螺栓DIN608Flatｃｏｕｎｔersunk short square neck bolts97六角头精配螺栓（长螺纹）DIN609Hexagon fitted bolts,long thread 98六角头精配螺栓（短螺栓）DIN610Hexagon fitted bolts short thread 99滚花平头螺钉DIN653GB835-88Knurled thumb screws thin type 100半圆头铆钉DIN660GB867-86ISO1051Round head rivets101沉头铆钉DIN661GB869-86ISO1051Contersunk head rivets102半沉头铆钉DIN662ISO1051Raised contersunk head rivets103大扁头铆钉DIN674ISO1051Mushroom head rivets104重型侧面带孔圆螺母DIN703Adjusting rings,heavy range(shafting collars)105侧面带孔圆螺母DIN705GB816-88Adjusting rings,light range(shafting collars)106卡头DIN741Wire rope clips107T型槽螺钉DIN787ISO299T-slot screws108双头螺柱（牙长=2D）DIN835GB900-88Studs-metal(end=2d)109内六角锥型闭锁螺钉DIN906Hexagon socket pipe plugs,conical thread110内六角直型闭锁螺钉DIN908Thread 111外六角锥型闭锁螺钉DIN909Thread112外六角直型闭锁螺钉DIN910Hexagon head screw plugs,cyl.thread113薄型盲螺母DIN917Hexagon cap nuts114开槽小圆柱头螺钉DIN920Slotted short cheese head screws 115开槽大圆柱头螺钉DIN921GB838-88Slotted large cheese head screws116开槽圆柱头轴肩螺钉DIN923GB830-88Slotted pan head screw with shoulder117开槽无头轴肩螺钉DIN927Slotted shoulder screws118焊接方螺母DIN928GB/T13680-92Square weld nuts119焊接六角螺母DIN929GB/T13681-92Hexagon weld nuts120六角头螺母DIN970Hexagon nuts type-1121六角头螺母DIN971Hexagon nuts type-2122细牙六角头螺母（2型）DIN972Hexagon nuts with fine thread123开槽六角螺母DIN935GB6178-86ISO7035Hexagon slotted andｃａｓｔle nuts124六角头开槽薄螺母DIN937GB6181-86ISO7038Hexagon thin slotted and caslte nuts125双头螺距（牙长=1D）DIN938GB897-88Studs metal(end=1d) 126双头螺距（牙长=1.5D DIN939GB898-88Studs metal(end=1.25d)127双头螺距（牙长=1.25D DIN940Studs metal(end=1.5d)128六角头细牙螺栓（全牙）DIN960GB5785-86ISO8765Hexagon head bolts,metric fine pitch thread129六角头细牙螺栓（半牙）DIN961GB8786-86ISO8676Hexagon head bolts,metric fine pitch thread130头部穿孔六角头螺栓DIN962Additional shapes and versions for bolts131牙条（全螺纹）DIN975GB6176-86ISO8674Threaded rods(studdings) 132螺纹销DIN976GB15389-94Threaded pins(stud bolts)133六角头开槽薄螺母2型DIN979Hexagon thin slotted andｃａｓｔle nuts134全金属六角锁紧螺母1型DIN980Prevaillng rorque type hexagon nuts,all metal nuts135圆螺母DIN981GB6184-86ISO7199Locknuts136配合垫片DIN988Shim rings137木材连接用垫片DIN1052Washers for timber connectors 138沉头钢钉DIN1151Round plain head nails139销钉专用垫片A型DIN1440ISO8738Plain washers for clevis pins(A) 140销钉专用垫片DIN1441Plain washers for clevis pins 141带头销钉DIN1444ISO2341Clevis pins with head142圆锥型槽销DIN1471GB/T13829.2ISO8744Grooved pins,taper grooved143圆锥型槽销（半槽）DIN1472GB/T13829.2ISO8745Grooved pins,taper grooved half length144平行槽销（带倒角）DIN1473ISO8740Grooved pins,parallel grooved full length145前端凹槽槽销DIN1474ISO8741Grooved pins,reverve grooved half length146中部凹槽槽销DIN1475ISO8742Grooved pins,center grooved 147圆头槽销DIN1476ISO8746Grooved pins with round head148沉头槽销DIN1477ISO8747Grooved pins withｃｏｕｎｔersunk head149六角螺母棒DIN1479Turnuckles(center parts),made out of hexagon bar150花蓝螺栓DIN1480Turnuckles with eye bolt and hook bolt151弹性圆柱销DIN1481GB879-86ISO8752Spring pins,heavy type 152组合式盖型螺母DIN1587GB802-88Hexagon domed cap nuts153开槽圆螺母(配合沟头扳手)DIN1804Slotted round nuts for hook spammer154圆螺母（带插销孔）DIN1816Round nuts with set holes155盘型弹簧垫圈DIN2093Disc springs156喉箍DIN3017Hose clamps157润滑油嘴（旋扭头）DIN3404Lubricating nipples,button head 158管夹DIN3567Shackles for conduilts159U型螺栓DIN3570Stirrup bolts(U-bolts)160球面垫圈DIN6319GB849-88Spherical washers,conical seats 161圆柱销DIN6325ISO8734Parallel pins162厚六角螺母DIN6330GB56-88Hexagon nuts,1.5d163厚六角法兰面螺母DIN6331GB6177-86Hexagon nuts,1.5d with collar 164长六角螺母DIN6334Hexagon nuts,3d165外齿锁紧垫圈DIN6797-A GB862.1-87External teeth lock washers166内齿锁紧垫圈DIN6797-I GB861.1-87Internal teeth lock washers167外锯齿锁紧垫圈DIN6798-A GB862.2-87External teeth serrated lock washers168内锯齿锁紧垫圈DIN6798-I GB861.2-87Internal teeth serrated lock washers169开口挡圈DIN6799GB896-76Retaining rings for shafts(E-rings),circlips170平键（A型）DIN6885ISO773/2491Parallel keys(form A)171半圆键DIN6888ISO3912Woodruff keys172嵌环（支撑环）DIN6899Thimbles173机器螺钉和垫圈组合件DIN6900Screws and washers assemblies174自攻螺钉和垫圈组合件DIN6901GB9074.1-17Tapping screws and washer assemblies175薄型带孔内六角圆柱螺钉DIN6912GB9074.18-23Hexagon cocket head cap screwswith hole,low head176大六角头螺栓DIN6914Hexagon head bolts with large head177大六角螺母DIN6915Hexagon nuts with large wideth across flat178大垫圈DIN6916Round washers for friction grip bolts179楔型方垫圈DIN6917Spuare taper washers for friction grip bolts on T-180六角法兰面螺母DIN6923GB6187-86ISO4161Hexagon flange nuts181全金属六角锁紧螺母2型DIN6925GB6185.1-2000ISO7042Prevailing torque type hexagonnuts,all metallic nuts182轻型弹性圆柱销DIN7346ISO13337Spring pins,light type183重型弹性圆柱销用垫圈DIN7349Washers for bolts with heavy type spring pinss184ISO公制螺纹螺钉多种头型DIN7500Thread forming screws for ISO-metric thread185开槽切削螺纹螺钉（多种头型）DIN7513Thread cutting screws186十字槽切削螺纹螺钉（多种头型）DIN7516Thread cutting screws crossrecess187T型四爪螺母DIN7965Tee nuts with pronge188钢结构用六角头螺栓连接副DIN7968GB1228/1229/1230Hexagon head fitted bolts forsteel structures189圆柱头螺钉用弹簧垫圈DIN7980ISO8738Spring lock washers for screws with cylindrical heads190薄型内六角圆柱头螺钉DIN7984Hexagon socket head cap screws with,reduced head191钢结构用垫圈DIN7989GB1230-84Washers for steel structures192钢结构用六角头螺栓DIN7990GB1229-84Hexagon head bolts for steel structures193轴用钢丝挡圈DIN7993GB895.2-86Roundwire snap rings for shafts194十字槽半沉头木螺钉DIN7995GB952-86Cross recessed raisedｃｏｕｎｔersunk head wood screws195十字槽圆头木螺钉DIN7996GB950-86Cross recessed round head wood screws196十字槽沉头木螺钉DIN7997GB951-86Cross recessedｃｏｕｎｔersunk head wood screws197螺纹护套(普通、自锁等)DIN8140Ciolｉｎｓｅｒｔs,coarse,fine thread,silf locking198大外径垫圈DIN9021GB96-85ISO7093Washers,outside diameter appro.3d 199弹簧卡子DIN11024sping cotter for a bolt200平板螺栓DIN13257Belting bolts(elevator bolts)201干壁钉（墙板钉）DIN18182Dry wall screws202环型螺母DIN28129GB63-88Lifting nuts(eye nuts)203圆螺母用止退DIN70952Tab washer for slotted round nuts 204圆锥销DIN1GB117ISO2339Taper pins205圆柱销DIN7GB119-86ISO2339Parallel pins206开槽圆柱头螺钉DIN84GB65-85ISO1207Slotted cheese head screws207开槽盘头螺钉DIN85GB67-85ISO1580Slotted pan head screws208单耳止动垫圈DIN93GB854Tab washers209开口销DIN94GB91ISO1234ｓｐｌｉｔcooter pins。
DIN_中文_英文对照
方斜垫圈（ I 型） 方垫圈 开槽凹端紧定螺钉 六角薄螺母 细牙六角薄螺母 木螺钉专用垫圈 密封帽 活节螺栓 B 型 内舌止动垫圈 双耳止动垫圈 滚花高头螺钉 开槽滚花高头螺钉 滚花高螺母 滚花薄螺母 锁紧垫圈 轴用弹性垫圈 孔用弹性垫圈 方头带垫螺栓 方头圆柱底端螺栓 方头带垫关圆底端 螺栓 T 型槽螺母 单头螺柱 地脚螺栓 带槽圆螺母 端面带孔圆螺母 开槽平端紧定螺钉 开槽锥端紧定螺钉 六角螺母 方螺母 -C 六角头螺钉 六角头圆柱端 紧定螺钉 薄型方螺母 -B
中文品名 Description in Chinese 圆锥销 圆柱销 开槽圆柱头螺钉 开槽盘头螺钉 单耳止动垫圈 开口销 开槽半沉头木螺钉 开槽半圆头木螺钉 开槽沉头木螺钉 平垫 平垫（带倒角） 平垫 重型弹垫 标准弹垫 鞍形弹垫 弹簧止动垫圈 波形弹垫 T 型方颈螺栓 T 型双接头螺栓 螺纹圆锥销 T 型头螺栓 蝶型螺母（美制） 蝶型螺母（德制） 蝶型螺母（美制） 蝶型螺母（德制） 圆球型盖型螺母 开槽带孔球面 圆柱头蚴钉 开槽长圆柱端 紧定螺钉 开槽平端 紧定螺钉（半牙） 小六角特薄细牙 螺母 外舌止动垫圈 小垫圈 (用于圆柱头螺钉) 方斜垫圈（ U 型）
87
DIN906
Hexagon socket pipe plugs,conical thread
88
DIN908
Thread
89
DIN909
Thread
90 91 92 93
DIN910 DIN911 DIN912 DIN913
Hexagon head screw plugs,cyl.thread Socket wrenches Hexagon socket cap screws Hexagon socket set screws with falt point
haso标准件中英文对照
haso标准件中英文对照HASCO Z标准件系列Z00 导柱Guide pillarZ01 导柱Guide pillarZ011 导柱Guide pillarZ012 导柱Guide pillarZ013 导柱Guide pillarZ014 导柱Guide pillarZ0141 导柱连接端End p ieceZ0142 导柱连接端End p ieceZ015 导柱Guide pillarZ0151 导柱连接端（Z015/…专用）Pillar ada pter Z0152 导柱连接端Pillar ada pterZ02 顶杆Ejector rodZ022 导管Guide sleeveZ03 导柱Guide pillarZ05 圆锥形管精定位Locating unit, roundZ055 圆形垫片SpacerZ056 圆形垫件SpacerZ06 平锥形导块Locating unitZ07 长方形导块Square guide barZ08 直身方形管位导块Pre-centering unitZ081 方形垫片Sp acer discZ091 方形定位锁块（公）Square interlockZ092 方形定位锁块（母）Square interlockZ093 方形定位锁块（母）Square interlockZ10 导套Guide bushZ10W 自润滑导套Guide bushZ11 导套Guide bushZ11W 自润滑导套Guide bushZ12 滚珠导套Ball guide bushZ13W 自润滑导套Self lubric.Guide bush Z15W 自润滑垫片Self lubric. Flat stock Z16W 自润滑垫片Self lubric. Guide rail Z17 长方形导块（Z07/...专用）Guide retainerZ20 定板导套Centering sleeveZ25 定位销Dowel pinZ26 定位销Dowel pinZ28 六角螺母Hexagon nutZ281 六角螺母Hexagon nutZ282 六角螺母Hexagon nutZ285 螺母Nut for T-slotsZ286 螺母Nut for T-slotsZ30 胚头内六角螺丝Socket head cap screwZ31 胚头内六角螺丝Socket head cap screwZ32 薄胚头内六角螺丝Socket head cap screwZ33 薄胚头内六角螺丝Countersunk screwZ34 内六角螺丝Hexagon socket set screw Z35 内六角螺丝Hexagon socket set screw Z351 内六角螺丝Hexagon socket set screw Z352 螺丝杆Locking screwZ36 弹簧滚珠螺丝Sp ring pl ungerZ361 弹簧滚珠螺丝Sp ring pl ungerZ37 弹簧滚珠螺丝Sp ring pl ungerZ370 弹簧定位螺丝Sp ring pl ungerZ371 弹簧滚珠螺丝Sp ring pl ungerZ372 弹簧定位螺丝Sp ring pl ungerZ3721 弹簧定位螺丝Sp ring pl ungerZ373 弹簧定位镶件Sp ring pl ungerZ374 弹簧滚珠镶件Sp ring pl ungerZ375 弹簧滚珠镶件Sp ring pl ungerZ38 限位螺丝Shoulder screwZ381 螺丝Slotted shoulder screw Z39 螺丝Slotted shoulder screw Z40 顶针（全硬）Ejector pinZ41 顶针（表层硬）Ejector pinZ42 顶头顶针（全硬）Ejector pinZ43 顶头顶针（表层硬）Ejector pinZ44 有托顶针（表层硬）Shouldered ejector pin Z441 有托顶针（全硬）Shouldered ejector pin Z442/.../S 有托顶针（定制件）Ejector pinZ45 司筒（表层硬）Ejector sleeveZ451 司筒（全硬）Ejector sleeveZ4501 司筒（全硬）Ejector sleeveZ452/ -/S 司筒（定制件）Ejector sleeveZ453/ -/S 司筒（定制件）Ejector sleeveZ454/ …/S 司筒（定制件）Ejector sleeveZ455/ …/S 司筒（定制件）Ejector sleeveZ456 顶针耐磨镶件Wear sleeveZ456/…/S 顶针耐磨镶件（定制件）Wear sleeveZ46 扁顶针（表层硬）Flat ejector pinZ461 特殊扁顶针Sp ecial flat ejectorZ462 特殊扁顶针镶件（Z461/…专用）GuideZ465 扁顶针（全硬）Flat ejector pinZ466/ …/S 扁顶（定制件）Flat ejector pinZ47 顶针延长杆Extension rodZ48 年月标记镶件Date insertZ4800 标记镶件Marking insertZ4801 更新标记镶件Renew insertZ481 更新年份镶件Year insertZ482 月份标记镶件Month insertZ483 年份标记镶件Year insertZ484 箭头标记镶件Arrow insertZ485 年月标记镶件Date insertZ4851 更新年份镶件Year insertZ4861/1 塑料标记镶件Resin marking insert Z4861/2 班别标记镶件Shift marking insert Z4861/3 日期标记镶件Day marking insertZ4861/4 月份标记镶件Month-marking insert Z4861/5 年份标记镶件Year-marking insert Z4863 年月日标记镶件Multi. Marking insert Z4864 年月日塑料标记镶件Multi. Marking insert Z487/1 “回收标记”嵌件Recycling insertZ487/2 “回收标记”嵌件Recycling insertZ487/3 “回收标记”嵌件Recycling insertZ488 CE标记镶件CE marking insertZ489 食物标记镶件Food marking insert Z49 模芯镶件Core pin Z491 气动顶出阀Air valveZ492 模芯镶件Cpre pinZ495 喷气块Blow off stripZ4951 喷气咀Blow off nozzleZ50 唧咀Sprue bushingZ51 唧咀Sprue bushingZ511 唧咀Sprue bushingZ512 唧咀Sprue bushingZ515 气动唧咀Pneumatic nozzleZ516 细水口镶件Nozzle insertZ518 唧咀Sprue bushingZ519 唧咀Sprue bushingZ53 扣水口镶件Sprue p ullerZ55 顶针板园垫件Stop pinZ551 顶针板园垫件Stop pinZ56 环子Head for ejector rod Z561 环子Head for ejector rodZ562 介子WasherZ57 园形垫件Support p illarZ571 园形垫件Support p illarZ60 园线弹簧Comp ression sp ring Z601 园线弹簧Comp ression sp ring Z62 蝶形弹簧Disc sp ringZ64 方线弹簧Comp ression sp ringZ65 扁线弹簧Comp ression sp ring Z67 弹弓介子环Retaining ringZ671 弹弓介子钳Mounting p liersZ68 弹弓介子环Retaining ringZ681 弹弓介子钳Mounting p liersZ69 螺丝介子Sp ring washerZ691 螺丝介子Sp ring washerZ70 吊架连吊环Lifting deviceZ701 调距螺栓Distance boltZ71 吊环Eye boltZ711 吊环Eye boltZ712 吊环Eye boltZ72 吊环Eye boltZ73 安全扣T ool safety device Z741 固定玛夹Power clam pZ7411 空板架Sp acer blockZ7412 空板架Sp acer blockZ742 固定玛夹Power clam pZ743 固定玛夹Power clam pZ75 固定玛夹Clam p systemZ751 T头螺丝T head boltZ752 T头螺丝T head boltZ7521 T头螺丝T head boltZ7522 T头螺丝T head boltZ753 介子环Sp herical washerZ754 介子环Conical seat washer Z755 介子环Conical seat washer Z76 快速玛夹模装置Quick clam ping jig Z761 快速玛夹模板Clam ping p lateZ762 玛夹导柱Clam ping boltZ763 玛夹锁钉Eccentric boltZ765 离合锁（套）Locking housingZ766 离合锁（插）Locking plugZ80 带阀快接喉套Shut-off coup ling Z80/ …/45 带阀快接喉套Shut-off coup ling Z80/ …/90 带阀快接喉套Shut-off coup ling Z801 快接喉套Coup lingZ801/…/45 快接喉套Coup lingZ801/…/90 快接喉套Coup lingZ805 带阀侨式快接喉套Diverting coup ling Z8051 侨式快接喉套Diverting coup ling Z807 带阀快接喉套Shut-off coup ling Z807/ …/45 带阀快接喉套Shut-off coup ling Z807/ …/90 带阀快接喉套Shut-off coup lingZ808 快接喉套Coup lingZ809 带阀快接喉套Multi. shut-off couplingZ81 快接喉咀Nipp leZ81/ …/90 喉嘴Nipp leZ811 带阀快接喉咀Shut-off ni ppleZ812 适配连接头Double sided connector Z814 适配连接头Ada pterZ815 适配连接头Ada pterZ817 喉咀Hose nippleZ819 带阀快接喉咀Multi. shut-off ni pp le Z82 带阀快接喉套Shut-off coup lingZ83 喉咀Hose connectorZ831 快接喉套Plug-in connectorZ84 PVC喉管PVC-HoseZ85 PVC喉管PVC-HoseZ851 PVC喉管PVC-HoseZ853 耐高温喉管Viton-HoseZ854 耐高温喉管T eflon-HoseZ855 耐高温喉管Corrugated metal hoseZ86 喉箍Hose cli pZ861 紧夹用喉箍Crim ping sleeveZ865 紧夹用喉钳Crim ping toolZ87 喉咀Hose nippleZ875 喉咀Hose nippleZ876 喉咀Hose nippleZ876/ …/45 喉咀Hose nippleZ876/ …/90 喉咀Hose nippleZ877 连接头Joining p ieceZ878 转曲连接头ConnectorZ88 喉咀Hose nippleZ89 喉咀Hose nippleZ90 加长快接喉咀Extension nippleZ905 适配连接头Ada pterZ906 延长管Extension tubeZ91 加长喉咀Extension tubeZ93 密封胶布Sealing tape (Teflon)Z94 喉塞Tap ered plugZ941 喉塞Tap ered plugZ942 膨胀喉塞Sealing plugZ945/1 套装拉胀喉塞工具Assembly-setZ945/2 套装拉胀喉塞工具Assembly-setZ947/1 拉胀工具延长杆Extended scale tube Z947/2 拉胀工具延长杆Extended scale tubeZ95 钢管Brass tubeZ96 运水铝质螺旋芯（单）Sp iral coreZ961 运水铝质螺旋芯（双）Sp iral coreZ962 运水针Junction tubeZ964 运水回路胶环（小）Diverting elementZ9641 运水回路胶环（大）Diverting elementZ965 运水胶隔片Plug baffleZ967 隔水片Baffle coreZ968 运水胶质螺旋芯Sp iral coreZ969 运水胶质螺旋芯Sp iral coreZ97 运水针Cascade water junction Z975 特快导热针Heat pipe Z98 耐高温密封胶圈O-RingZ1001 阀针Needle valveZ101 电热喷咀Hot nozzleZ101G 电热喷咀Hot nozzleZ101R 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ1011 电热喷咀内胆Inner part of nozzle Z1011M 电热喷咀内胆Inner part of nozzle Z1015 金属密圭寸圈Metall O-Ring Z103 电热喷咀Hot nozzleZ103G 电热喷咀Hot nozzleZ103R 电热喷咀Hot nozzleZ1031 电热喷胆内胆Inner part of nozzle Z103T 电热喷咀Hot nozzleZ103GT 电热喷咀Hot nozzleZ103RT 电热喷咀Hot nozzleZ103 仃电热喷胆内胆Inner part of nozzle Z103M 电热喷咀Multi ple gate nozzle Z1031M 电热喷胆内胆Inner part of nozzle Z10320 电热喷咀Muitl ple gate nozzle Z10370 电热喷咀Muitl plegate nozzle Z104 电热喷咀Hot nozzleZ104G 电热喷咀Hot nozzleZ104R 电热喷咀Hot nozzleZ1041 电热喷胆内胆Inner part of nozzle Z104E 电热喷咀Hot nozzleZ104GE 电热喷咀Hot nozzleZ1041E 电热喷胆内胆Inner part of nozzle Z104GV 电热喷咀Hot nozzleZ1041V 电热喷咀内胆Inner part of nozzle Z10420 电热喷咀Muitl ple gate nozzle Z1052 圆形隔热垫件Distance ring Z1055 炉头接驳衬套Spure bushingZ106 热流道板ManifoldZ10600 热流道板ManifoldZ1061 密封塞钉P lugZ1062 密圭寸圈Sealing washerZ1063 六角螺丝Hexagon head screwZ1064 保温铝板Reflector sheetZ1067 套装零件Accessory kitZ107 气动针阀Needte valveZ1072 针阀司套Needle guide sleeveZ1073 针阀司套Needle guide sleeveZ1076 圆形隔热垫环Distance ringZ109 过滤器Filter cartridgeZ1095 过滤器Filter cartridgeZ110 发热棒Cartridge heaterZ111 发热棒Cartridge heaterZ1133 发热环Heater bandZ1134 发热环Heater bandZ1138 发热管（可弯曲）Fiexble heaterZ116 套装接线工具Assembly setZ1161 耐高温电线Extension cableZ1162 线耳Crimp type bracketZ1164 耐高温电线Extension cableZ1165 连接管Butt jointZ1166 线耳Cable end sleeveZ1167 套件Assembly kitZ1168 热电偶线Signal cableZ121 隔热板（洞、无洞）Insulating sheetZ1211 隔热板（洞、无洞）Thermal insulating sheetZ122 电热温控器T em perature controllerZ1221 温控器组件ModuleZ1224 插座嵌件Socket insertZ1225 温控器连接线Connection po wer/signal cable Z1226 温控器连接线（转换用）Ada pterZ1227 插座ScoketZ1228 插座ScoketZ1229 插座嵌件InsertZ123 多组温控器Multi zone control systemZ125 温控器T em perature controllerZ126/1 温控器T em perature controllerZ126/2 温控器T em perature controllerZ1261 温控器ModuleZ1262 盖板Cover PlateZ127 插头P lug。
最新DIN标紧固件的中文对照
DIN标紧固件的中文对照序号德国标准中文译文4 DIN 1 圆锥销5 DIN 7 圆柱销6 DIN 84 开槽圆柱头螺钉7 DIN 85 开槽盘头螺钉8 DIN 93 单耳止动垫圈9 DIN 94 开口销10 DIN 95 开槽半沉头木螺钉11 DIN 96 开槽半圆头木螺钉12 DIN 97 开槽沉头木螺钉13 DIN 125-1 平垫14 DIN 125-2 平垫(带倒角)15 DIN 126 平垫16 DIN 127-1 重型弹垫17 DIN 127 标准弹垫18 DIN 128-1 波形弹垫19 DIN 137-1 弹簧止动垫圈20 DIN 137-2 鞍形弹垫21 DIN 186 T型方颈螺栓22 DIN 188 T型双接头螺栓23 DIN 258 螺纹圆锥销24 DIN 261 T型头螺栓25 DIN 315AF 蝶型螺母(美制)26 DIN 315DF 蝶型螺母(德制)27 DIN 316AF 蝶型螺钉(美制)28 DIN 317DF 蝶型螺钉(德制)29 DIN 319 圆球型盖型螺母30 DIN 404 开槽带孔球面圆柱头螺钉DIN40531 DIN 417 开槽长圆柱端紧定螺钉32 DIN 427 开槽平端紧定螺钉(半牙)33 DIN 431 小六角特薄细牙螺母34 DIN 432 外舌止动垫圈35 DIN 433 小垫圈(用于圆柱头螺钉)36 DIN 434 方斜垫圈(U型)37 DIN 435 方斜垫圈(I型)38 DIN 436 方垫圈39 DIN 438 开槽凹端紧定螺钉40 DIN 439 六角薄螺母41 DIN 439 六角薄螺母B级无倒角42 DIN 439 细牙六角薄螺母43 DIN 440 木螺钉专用垫圈44 DIN 443 密封帽45 DIN 444 活节螺栓B 型46 DIN 462 内舌止动垫圈47 DIN 463 双耳止动垫圈48 DIN 464 滚花高头螺钉49 DIN 465 开槽滚花高头螺钉50 DIN 466 滚花高螺母51 DIN 467 滚花薄螺母52 DIN 470 锁紧垫圈53 DIN 471 轴用弹性挡圈54 DIN 472 孔用弹性挡圈55 DIN 478 方头带垫螺栓56 DIN 479 方头圆柱底端螺栓57 DIN 480 方头带垫半圆底端螺栓58 DIN 481 弹性圆柱销59 DIN 508 T型槽螺母60 DIN 525 单头螺柱61 DIN 529 地脚螺栓62 DIN 546 带槽圆螺母63 DIN 547 端面带孔圆螺母64 DIN 551 开槽平端紧定螺钉65 DIN 553 开槽锥端紧定螺钉66 DIN 555 六角螺母67 DIN 557 方螺母-C68 DIN 558 六角头螺钉69 DIN 561 六角头圆柱端紧定螺钉70 DIN 562 薄型方螺母-B71 DIN 571 六角头木螺钉72 DIN 580 吊环螺钉73 DIN 582 吊环螺母74 DIN 601 六角头螺栓75 DIN 603 大半圆头方颈螺栓(马车螺栓) C级76 DIN 604 沉头带插销马车螺栓77 DIN 605 沉头长方颈马车螺栓78 DIN 607 半圆头带插销马车螺栓79 DIN 608 沉头短方颈马车螺栓80 DIN 609 六角头精配螺栓（长螺纹）81 DIN 610 六角头精配螺栓（短螺纹）82 DIN 653 滚花平头螺钉83 DIN 660 半圆头铆钉84 DIN 661 沉头铆钉85 DIN 662 半沉头铆钉86 DIN 674 大扁头铆钉87 DIN 703 重型侧面带孔圆螺母88 DIN 705 侧面带孔圆螺母89 DIN 741 卡头90 DIN 787 T型槽螺钉91 DIN 835 双头螺柱（牙长=2D）92 DIN 906 内六角锥型闭锁螺钉93 DIN 908 内六角直型闭锁螺钉94 DIN 909 外六角锥型闭锁螺钉95 DIN 910 外六角直型闭锁螺钉96 DIN 911 内六角扳手97 DIN 912内六角圆柱头螺钉98 DIN 913 内六角平端紧定螺钉99 DIN 914 内六角尖端紧定螺钉100 DIN 915 内六角圆柱端紧定螺钉101 DIN 916 内六角凹端紧定螺钉102 DIN 917 薄型盲螺母103 DIN 920 开槽小圆柱头螺钉104 DIN 921 开槽大圆柱头螺钉105 DIN 923 开槽圆柱头轴肩螺钉106 DIN 927 开槽无头轴肩螺钉107 DIN 928 焊接方螺母108 DIN 929 焊接六角螺母109 DIN 931 六角头螺栓（半牙）110 DIN 933 六角头螺栓（全牙）111 DIN 934 六角头螺母(1型)112 DIN 934-2 细牙六角头螺母(1型) 113 DIN 935 开槽六角螺母114 DIN 936 六角头薄螺母115 DIN 937 六角头开槽薄螺母116 DIN 938 双头螺距（牙长=1D）117 DIN 939 双头螺距（牙长=1.25D）118 DIN 939 双头螺距（牙长=1.5D）119 DIN 940 双头螺距（牙长=1.5D）120 DIN 960 六角头细牙螺栓（半牙）121 DIN 961 六角头细牙螺栓（全牙）122 DIN 962 头部穿孔六角头螺栓123 DIN 963 开槽沉头螺钉124 DIN 964 开槽半沉头螺钉125 DIN 965 十字槽沉头螺钉126 DIN 966 十字槽半沉头螺钉127 DIN 970 六角头螺母128 DIN 971 六角头螺母129 DIN 972 细牙六角头螺母(2型)130 DIN 975 牙条(全螺纹)131 DIN 976 螺纹销132 DIN 979 六角头开槽薄螺母（2型）133 DIN 980 全金属六角锁紧螺母（1型）134 DIN 981 圆螺母135 DIN 982 六角头尼龙锁紧螺母136 DIN 985 六角头薄型尼龙锁紧螺母137 DIN 986 六角盖型尼龙锁紧螺母138 DIN 988 配合垫片139 DIN 1052 木材连接用垫片140 DIN 1151 沉头钢钉141 DIN 1440 销钉专用垫片A型142 DIN 1441 销钉专用垫片143 DIN 1444 带头销钉144 DIN 1471 圆锥型槽销145 DIN 1472 圆锥型槽销(半槽)146 DIN 1473 平行槽销(带倒角)147 DIN 1474 前端凹槽槽销148 DIN 1475 中部凹槽槽销149 DIN 1476 圆头槽销150 DIN 1477 沉头槽销151 DIN 1479 六角螺母棒152 DIN 1480 花篮螺栓153 DIN 1481 弹性圆柱销开槽重型154 DIN 1587 组合式盖型螺母155 DIN 1804 开槽圆螺母（配合沟头扳手）156 DIN 1816 圆螺母（带插销孔）157 DIN 2093 盘型弹簧垫圈158 DIN 3017 喉箍159 DIN 3404 润滑油嘴（旋扭头）160 DIN 3567 管夹161 DIN 3570 U型螺栓162 DIN 5587 2型六角螺母A和B级163 DIN 6319 球面垫圈164 DIN 6325 圆柱销165 DIN 6330 厚六角螺母166 DIN 6331 厚六角法兰面螺母167 DIN 6334 长六角螺母168 DIN 6797-A 外齿锁紧垫圈169 DIN 6797-I 内齿锁紧垫圈170 DIN 6798-A 外锯齿锁紧垫圈171 DIN 6798-I 内锯齿锁紧垫圈172 DIN 6799 开口挡圈173 DIN 6823 六角法兰面螺母174 DIN 6885 平键（A型）175 DIN 6888 半圆键176 DIN 6899 嵌环（支撑环）177 DIN 6900 机器螺钉和垫圈组合件178 DIN 6901 自攻螺钉和垫圈组合件179 DIN 6912 薄型带孔内六角圆柱头螺钉180 DIN 6914 大六角头螺栓181 DIN 6915 大六角螺母182 DIN 6916 大垫圈183 DIN 6917 楔型方垫圈184 DIN 6921 六角法兰面螺栓加大系列B级185 DIN 6923 六角法兰面螺母186 DIN 6925 全金属六角锁紧螺母(2型）187 DIN 7337 开口型抽芯铆钉（沉头、扁圆头）188 DIN 7338 扁平头半空心/全空心铆钉189 DIN 7343 螺旋夹紧销190 DIN 7346 轻型弹性圆柱销191 DIN 7349 重型弹性圆柱销用垫圈192 DIN 7500 ISO公制螺纹螺钉(多种头型)193 DIN 7504 自攻自钻螺钉(多种头型)194 DIN 7513 开槽切削螺纹螺钉(多种头型) 195 DIN 7516 十字槽切削螺纹螺钉(多种头型) 196 DIN 7965 T型四爪螺母197 DIN 7968 钢结构用六角头螺栓连接副198 DIN 7971 开槽盘头自攻螺钉199 DIN 7972 开槽沉头自攻螺钉200 DIN 7973 开槽半沉头自攻螺钉201 DIN 7976 六角头自攻螺钉202 DIN 7978 圆锥销203 DIN 7980 圆柱头螺钉用弹簧垫圈204 DIN 7981 十字槽盘头自攻螺钉205 DIN 7982 十字槽沉头自攻螺钉206 DIN 7983 十字槽半沉头自攻螺钉207 DIN 7984 薄型内六角圆柱头螺钉208 DIN 7985 十字槽盘头螺钉209 DIN 7989 钢结构用垫圈210 DIN 7990 钢结构用六角头螺栓211 DIN 7991 内六角沉头螺钉212 DIN 7993 轴用钢丝挡圈213 DIN 7995 十字槽半沉头木螺钉214 DIN 7996 十字槽圆头木螺钉215 DIN 7997 十字槽沉头木螺钉216 DIN 8140 螺纹护套（普通\自锁等）217 DIN 9021 大外径垫圈218 DIN 11024 弹簧卡子219 DIN 13257 平板螺栓220 DIN 18182 干壁钉（墙板钉）221 DIN 28129 环型螺母222 DIN 70952 圆螺母用止退垫圈螺丝，紧固件，标准件词汇的中英文对照机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle 针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-Low Thread Screws不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors 石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts 普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝Carriage Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws旋入螺丝Drive Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts突缘螺丝Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铜螺丝Brass Screws铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts 拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt车辆(汽车)螺丝、螺帽Automotive Fasteners航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓Blind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging 自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives成型冲模Header Punches In Various Drives螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass)螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage 螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers 螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件Bearing Shaft(Motor)轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind Nuts拉钉Blind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动拉钉钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings 汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet Metal Fasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod。
低压电器标准规范中英文对照
低压电器标准规范中英文对照-技术标准1. GB/T 998-1982 低压电器基本试验方法Basic testing methodof low voltage apparatus2. GB/T 1003-1980 三相插头插座型式、基本参数与尺寸Types, basic parameters and dimensionsof three phase plugs and sockets3. GB 1444-1987 防爆灯具专用螺口式灯座Edison screw lampholders specially used forexplosion-proof luminaires4. GB/T 1497-1985 低压电器基本标准The basic standard for low-voltage apparatus5. GB 2099-1980 单相、三相插头插座技术条件Technical requirements for single-phase andthree- phase plugs and sockets6. GB/T 2900.18-1992 电工术语低压电器Electrotechnical terminology—Low voltage apparatus7. GB/T 3783-1994 船用低压电器基本要求General specification for low-voltage apparatus in ships8. GB/T 3797-1989 电控设备第二部分: 装有电子器件的电控设备Electric-driving controlgear—Part2: Electric-driving controlgear incorporating electronic devices9. GB 3836.1-1983 爆炸性环境用防爆电气设备通用要求Electrical apparatus for explosiveatmospheres--General requirements10. GB 3836.2-1983 爆炸性环境用防爆电气设备隔爆型电气设备"d" Electrical apparatus forexplosive atmospheres--Flameproof electrical apparatus "d"11. GB 3836.3-1983 爆炸性环境用防爆电气设备增安型电气设备"e" Electrical apparatus forexplosive atmospheres--Increased safety electrical apparatus "e"12. GB 3836.4-1983 爆炸性环境用防爆电气设备本质安全型电路和电气设备"i" Electrical apparatus forexplosive atmospheres--Intrinsically safe circuits and electrical apparatus"i"13. GB 3836.5-1987 爆炸性环境用防爆电气设备正压型电气设备"p" Electrical apparatus forexplosive atmospheres--Pressurized electrical apparatus "p"14. GB 3836.6-1987 爆炸性环境用防爆电气设备充油型电气设备"o" Electrical apparatus forexplosive atmospheres--Oil immersed electrical apparatus "o"15. GB 3836.7-1987 爆炸性环境用防爆电气设备充砂型电气设备"q" Electrical apparatus forexplosive atmospheres--Sand filled electrical apparatus"q"16. GB 3836.8-1987 爆炸性环境用防爆电气设备无火花型电气设备"n" Electrical apparatus forexplosive atmospheres--Non-sparking electrical apparatus "n"17. GB 3836.9-1990 爆炸性环境用防爆电气设备浇封型电气设备"m" Electrical apparatus forexplosive atmospheres—Encapsulated electrical apparatus "m"18. GB 3836.10-1991 爆炸性环境用防爆电气设备气密型电气设备"h" Electrical apparatus forexplosive atmospheres—Hermetically sealed electrical apparatus "h"19. GB 3836.11-1991 爆炸性环境用防爆电器设备最大试验安全间隙测定方法Electrical apparatus forexplosive atmospheres—Method of test for ascertainment of maximum experimentalsafe gap20. GB 3836.12-1991 爆炸性环境用防爆电器设备气体或蒸汽混合物按照其最大试验安全间隙和最小点燃电流的分级Electricalapparatus for explosive atmospheres—Classification of gases or vapours with airaccording to their maximum experimental safe gaps and minimum ignitingcurrents21. GB/T 4205-1984 控制电气设备的操作件标准运动方向Standard directions of movement foractuators which control the operation of electrical apparatus22. GB/T 4720-1984 电控设备第一部分: 低压电器电控设备Electric-driving controlgear--Part 1:Electric driving controlgear composed of low-voltage apparatus23. GB 5590-1985 矿用隔爆型电磁起动器Mining type flameproof electric magnetic starters24. GB 6829-1995 剩余电流动作保护器的一般要求General requirements for residual currentoperated protective devices25. GB/T 7061-1986 船用低压开关设备和控制设备装置通用技术条件General specification forlow-voltage switchgear and controlgear assemblies in ships26. GB/T 7261-1987 继电器及继电保护装置基本试验方法Basic testing method of relay andprotective equipment27. GB/T 7417-1987 AX 系列继电器AX series relays28. GB/T 7957-1987 矿用安全帽灯Safety cap lamp for mines29. GB/T 7958-1987 煤矿用电容式发爆器Capacitor discharge type exploders for coal mines30. GB/T 9393-1988 STZ3型电子测量仪器用连接器STZ3 type connector for electronic measurement instrument31. GB/T 9466-1988 低压成套开关设备基本试验方法Basic testing method of low-voltageswitchgear assembly32. GB/T 10217-1988 电工控制设备造型设计导则The design guide of the outline andstructure for the electric control equipment33. GB/T 10231-1988 保护继电器的结构型式与基本尺寸系列Structural type and series of basicdimensions of protective relay34. GB/T 10962-1989 机床电器可靠性通则General rules of reliability for machine tool electrical components35. GB/T 10964-1989 电器附件、控制器和保护器术语Electrotechnical terminology of electricalaccessories, controls and protectors36. GB/T 11918-1989 工业用插头插座和耦合器一般要求Plugs, socket-outlets and couplers forindustrial purposes—General requirement37. GB/T 11919-1989 工业用插头插座和耦合器插销和插套尺寸互换性的要求Plugs, socket-outlets andcouplers for industrial purposes—Dimensional interchangeability requiements forpin and contact-tube accessories38. GB/T 12173-1990 矿用一般型电气设备Mining electrical apparatus for non hazardous area39. GB 12476.1-1990 爆炸性粉尘环境用防爆电气设备粉尘防爆电气设备Electrical apparatus forexplosive dust atmosphere—Dust ignition-proof apparatus40. GB/T 12944.1-1991 高压穿墙瓷套管技术条件High-voltage ceramic wall bushings—Technical specifi cations41. GB/T 12944.2-1991 高压穿墙瓷套管尺寸与特性High-voltage ceramic wall bushings—Dimensions and characteristics42. GB/T 13539.1-1992 低压熔断器基本要求General requirements for low-voltage fuses43. GB 13539.2-1992 低压熔断器专职人员使用的熔断器的补充要求Low-voltage fuses —Supplementaryrequirements for fuses for use by authorized persons44. GB 13539.4-1992 低压熔断器半导体器件保护用熔断体的补充要求Low-voltage fuses—Supplementaryrequirements for fuse-links for the protection of semiconductor devices45. GB/T 14048.1-1993 低压开关设备和控制设备总则General rules for low-voltage switchgearand controlgear46. GB 14048.2-1994 低压开关设备和控制设备低压断路器Low-voltage switchgear and controlgear--Low-voltage circuit breakers47. GB 14048.3-1993 低压开关设备和控制设备低压开关、隔离器、隔离开关及熔断器组合电器Low-voltage switchgearand controlgear--Low-voltage switches, disconnectors, switch-disconnectors andfuse-combination units48. GB 14048.4-1993 低压开关设备和控制设备低压机电式接触器和电动机起动器Low-voltage switchgear andcontrolgear--Low-voltage electromechanical contactors and motor starters49. GB 14048.5-1993 低压开关设备和控制设备控制电路电器和开关元件第一部分机电式控制电路电器Low-voltageswitchgear and controlgear--Control circuit devices and switchingelements--section 1--Electromechanical control circuit devices50. GB/T 15510-1995 控制用电磁继电器可靠性试验通则General rules for reliability test ofelectromagnetic relay for control circuits51. GB 15934-1996 电线组件Cord sets52. GB 16837-1997 家用和类似用途移动式，无联锁、带开关及熔断器组合插座的安全要求Safety requirements forswitched and fused portable multiple socket-outlet without interlock forhousehold and similar purposes53. GB 13140.1-1997 家用和类似用途低压电路用的连接器件第1部分：通用要求Connecting devices for lowvoltage circuits for household and similar purposes--Part 1: Generalrequirements54. GB 16916.1-1997 家用和类似用途的不带过电流保护的剩余电流动作断路器(RCCB) 第1部分：一般规则Residualcurrent operated circuit-breakers without integral overcurrent protection forhousehold similar uses(RCCB)--Part 1: Genaral rules55. GB 16916.21-1997 家用和类似用途的不带过电流保护的剩余电流动作断路器(RCCB)第 2.1部分：一般规则对动作功能与线路电压无关的RCCB的适用性Residual current operated circuit-breakerswithout integral overcurrent protection for household and similaruses(RCCB)--Part 2.1: Applicability of the general rules to RCCB functionallyindependent of line voltage56. GB 16916.22-1997 家用和类似用途的不带过电流保护的剩余电流动作断路器(RCCB)第 2.2部分：一般规则对动作功能与线路电压有关的RCCB的适用性Residual current operated circuit-breakerswithout integral overcurrent protection for household and similar uses(RCCB)--Part 2.2: Applicability of the general rules to RCCB functionallydependent on line voltage57. GB 16917.1-1997 家用和类似用途的带过电流保护的剩余电流动作断路器(RCBO) 第1部分：一般规则Residual currentoperated circuit-breakers with integral overcurrent protection for household andsimilar uses (RCBO)--Part 1: General rules58. GB 16917.21-1997 家用和类似用途的带过电流保护的剩余电流动作断路器(RCB0) 第 2.1部分：一般规则对动作功能与线路电压无关的RCBO的适用性Residual current operated circuit-breakers withintegral overcurrent protection for household and similar uses (RCBO) Part 2.1:Applicability of the general rules to RCBO functionally independent of linevoltage59. GB 16917.22-1997 家用和类似用途的带过电流保护的剩余电流动作断路器(RCBO) 第 2.2部分：一般规则对动作功能与线路电压有关的RCBO的适用性Residual current operated circuit-breakers withintegral overcurrent protection for household and similar uses(RCBO) Part 2.2:Applicability of the general rules to RCBO functionally dependent on linevoltage60. GB/T 16935.1-1997 低压系统内设备的绝缘配合第一部分: 原理、要求和试验Insulation coordination foreguipment within low-voltage systems--Part 1: Principles、requirements andtests61. GB 9364.1-1997 小型熔断器第1部分: 小型熔断器定义和小型熔断体通用要求Miniature fuses Part 1:Definitions for miniature fuses and general requirement for miniature fuse-links62. GB 9364.2-1997 小型熔断器第2部分: 管状熔断体Miniature fuses Part 2: Cartridge fuse-links63. GB 9364.3-1997 小型熔断器第3部分; 超小型熔断体Miniature fuses Part 3: Sub-miniaturefuse-links64. GB 7251.1-1997 低压成套开关设备和控制设备第一部分: 型式试验和部分型式试验成套设备Low-voltage switchgearand controlgear assemblies--Part 1; Type-tested and partially type-testedassemblies65. GB 7251.2-1997 低压成套开关设备和控制设备第二部分: 对母线干线系统(母线槽)的特殊要求Low-voltageswitchgear and controlgear assemblies--Part 2: Particular requirements forbusbar trunking systems(busways)66. GB 7251.3-1997 低压成套开关设备和控制设备第三部分: 对非专业人员可进入场地的低压成套开关设备和控制设备--配电板的特殊要求Low-voltage switchgear and controlgear assemblies Part 3: Particularrequirements for low-voltage switchgear and controlgear assemblies intended tobe installed in places where unskilled persons have access for theiruse--Distribution boards67. GB 3836.13-1997 爆炸性气体环境用电气设备第13部分: 爆炸性气体环境用电气设备的检修Electrical apparatusfor explosive gas atmospheres--Part 13: Repair and overhaul for apparatus usedin explosive gas atmospheres68. GB/T 17193-1997 电气安装用超重荷型刚性钢导管Extra-heavy duty rigid steel conduits forelectrical installations69. GB/T 17194-1997 电气导管电气安装用导管的外径和导管与配件的螺纹Conduits for electricalpurposes--Outside diameters of conduits for electrical installations and threadsof conduits and fittings70. GB 17196-1997 连接器件连接铜导线用的扁形快速连接端头安全要求Connecting devices--Flatquick-connect terminations for electrical copper conductors--Safetyrequirements71. GB/T 9815-1998 家用及类似用途的熔断器Fuses for domestic and similar purposes72. GB 13140.2-1998 家用和类似用途低压电路用的连接器件第2部分: 作为独立部件的带螺纹型夹紧件的连接器件的特殊要求Connecting devices for low voltage circuits for household and similar purposesPart 2: Particular requirements for connecting devices as separate entities withscrew-type clamping units73. GB 13140.3-1998 家用和类似用途低压电路用的连接器件第2部分: 作为独立单元的带无螺纹型夹紧件的连接器件的特殊要求Connecting devices for low voltage circuits for household and similar purposesPart 2: Particular requirements for connecting devices as separate entities withscrewless-type clamping units74. GB 13140.4-1998 家用和类似用途低压电路用的连接器件第2部分: 作为独立单元的带剌穿绝缘型夹紧件的连接器件的特殊要求Connecting devices for low voltage circuits for household and similar purposesPart 2: Particular requirements for connecting devices as separate entities withinsulation piercing clamping units75. GB 17464-1998 连接器件连接铜导线用的螺纹型和无螺纹型夹紧件的安全要求Connecting devices--Safetyrequirements for screw-type and screwless-type clamping units for electricalcopper conductors76. GB 9816-1998 热熔断体的要求和应用导则Thermal-Links-Requirements and applicationguide77. GB 14536.1-1998 家用和类似用途电自动控制器第1部分: 通用要求Automatic electrical controlsfor household and similar use Part 1: General requirements78. GB/T 17499-1998 家用洗衣机电脑程序控制器Microcomputer controller for householdwashing machine79. GB 14048.7-1998 低压开关设备和控制设备辅助电器第1部分: 铜导体的接线端子排low-voltage switchgearand controlgear Ancillary equipment Section 1-Terminal blocks for copperconductors80. GB 14048.8-1998 低压开关设备和控制设备辅助电器第2部分: 铜导体的保护导体接线端子排Low-voltageswitchgear and controlgear Ancillary equipment Section 2: Protective conductorterminal blocks for copper conductors81. GB 14048.6-1998 低压开关设备和控制设备接触器和电动机起动器第2部分: 交流半导体电动机控制器和起动器Low-voltageswitchgear and controlgear Contactors and motor-starters Section 2: ACSemiconductor motor controllers and starters82. GB 14048.9-1998 低压开关设备和控制设备多功能电器(设备) 第2部分: 控制与保护开关电器(设备) Low-voltageswitchgear and controlgear Multiple function equipment Section 2: Control andprotective switching devices(or equipment)(CPS)83. GB 7251.4-1998 低压成套开关设备和控制设备第四部分: 对建筑工地用成套设备(ACS)的特殊要求Low-voltageswitchgear and controlgear assemblies Part 4: Particular requirements forassemblies for construction sites(ACS)84. GB 7251.5-1998 低压成套开关设备和控制设备第五部分: 对户外公共场所的成套设备动力配电网用电缆分线箱(CDCs)的特殊要求Low-voltage switchgear and controlgear assemblies Part 5: Particularrequirements for assemblies intended to be installed outdoors in publicplaces--Cable distribution cabinets (CDCs)for power distribution in networks85. GB 13140.5-1998 家用和类似用途低压电路用的连接器件第2部分: 扭接式连接器件的特殊要求Connecitng devicesfor low-voltage circuits for household and similar purposes Part 2: Particularrequirements for twist-on connecting devices86. GB 17701-1999 设备用断路器Circuit-breaker for equipment87. GB 10963-1999 家用及类似场所用过电流保护断路器Circuit-breakers for overcurrent protection for household and similar installation。
《机械设计基础》常用单词中英文对照
《机械设计基础》常用单词中英文对照- common words in Basis of Mechanical Designing一画1.V带V belt2.力force3.力矩moment4.工作载荷serving load5.干摩擦dry friction6.飞轮flier, flywheel7.内圈inner ring8切向键tangential key9.切应力tangential stress10.切削cutting11.双头螺柱stud12.尺寸dimension13.尺寸公差dimensional tolerance14.计算载荷calculating load15.主动轴drive shaft16.凸轮cam17.加工working18.半圆键half round key19.外圈outer ring.20.失效failure21.尼龙nylon22.平键flat key23.打滑slippage24.正火normalizing treatment25.正应力normal stress26.优化设计optimum design27.冲压punching28.动平衡dynamic balance29动载荷moving load30.压力pressure31.压应力compressive stress32压强pressure intensity33.压缩compress34.压缩应力compressive stress35.合金钢alloy steel36.向心轴承centripetal stress37.向心推力轴承centripetal thrust bearing38.导向键guide key39.导轨guide track40当量动载荷equivalent dynamic load41.曲柄 crank42.曲轴crank axle43.曲率半径curvature radius44.有色金属non ferrous metal45.机构mechanism46.机架framework47.机座machine base48.机械machine49.机械加工mechanical working50.机械零件machine element51.机器machine52.灰铸铁gray cast iron53.自锁self locking54.行星轮系planetary gear train55.许用应力allowable stress56.防松locking57.刨削planning58.寿命life59.应力stress60.应力集中stress concentration61.应变strain62.扭转torsion63扭转角angle of torsion64.抗压强度compression strength65抗拉强度tensile strength66.抗弯强度bending strength67.材料material68.极限应力limit stress69.极惯性矩polar moment of inertial70.花键spline71.连杆connecting rod72.周转轮系epicyclic gear train73.屈服强度yield strength74.底板base plate75.底座underframe76.径向力radial force77.径向当量动载荷radial equivalent dynamic load78.径向轴承journal bearing79.径向基本额定动载荷radial elementary rated life80.性能performance81.承载量load carrying capacity82.拉力pulling force83.拉伸tension84.拉伸应力tensile stress85.油膜oil film86.泊松比Poisson’s ratio87.直径diameter88.空心轴hollow axle89.空气轴承air bearing90表面处理surface treatment91.表面淬火surface quenching92转矩torque93.金属材料metallic material94.青铜合金bronze alloy95.非金属材料non metallic material96.齿轮gear97.齿轮模数module of gear teeth98.齿数tooth number99.保持架holding frame100.变应力dynamic stress101.变形deflection, deformation102.变载荷dynamic load103.轮系gear train104.垫片shim105.垫圈washer106.复合材料composite material107.带传动belt driving108.弯曲bend109.弯曲应力bending stress110.弯曲强度bending strength111.弯矩bending moment112.挡圈retaining ring113.残余应力residual stress114.残余变形residual deformation115.点蚀pitting116.相对运动relative motion117.相对滑动relative sliding118.相对滚动relative rolling motion119.矩形花键square key120.结构structure121.结构设计structural design121.结构钢structural steel122.耐磨性wearing quality123.脉动循环应力repeated stress124.轴shaft125.轴瓦bushing126.轴向力axial force127.轴向当量动载荷axial equivalent dynamic load 128.轴向基本额定动载荷axial elementary rated life129.轴承bearing130.轴承合金bearing metal131.轴承油沟grooves in bearing132.轴承衬bearing bush133.轴承座bearing block134.轴承盖bearing cap135.轴环axle ring136.轴肩shaft neck137.轴套shaft sleeve138.退刀槽tool escape139.钢材steel140.钩头楔键gib head key150.钩头螺栓gib head bolt151.挺杆tappet, tapper152.圆柱销cylindrical pin153.圆锥销cone pin154.圆螺母circular nut155.流体动力润滑hydrodynamic lubrication 156.流体静力润滑hydrostatic lubrication 157.润滑lubrication158.润滑油膜lubricant film159.热处理heat treatment160.热平衡heat balance161.疲劳fatigue162.疲劳失效fatigue failure163.疲劳寿命fatigue Life164.疲劳强度fatigue strength165.疲劳裂纹fatigue cracking166.离合器clutch167.紧定螺钉tightening screw168.胶合seizing of teeth169.能量energy170.脆性材料brittle material171.调质钢quenched and tempered steel 172.载荷load173.载荷谱load spectrum174.通用零件universal element175.速度velocity176.部件parts177.铆接riveting178.陶瓷ceramics179.预紧pretighten180.高速传动轴high speed drive shaft181.偏心载荷eccentric load182.偏转角deflection angle183.减速器reductor184.剪切应力shearing stress185.剪切应力shear stress186.基本额定动载荷elementary rated dynamic load 187.基本额定寿命elementary rated life188.密封seal189.密度density190.弹性变形elastic deformation191.弹性流体动力润滑elastohydrodynamic lubrication 192.弹性啮合elastic engagement193.弹性滑动elastic slippage194.弹性模量modulus of elasticity195.弹簧spring196.弹簧垫圈spring washer197.惯性力inertial force198.惯性矩moment of inertia199.接触应力contact stress200.接触角Contact Angle201.推力轴承thrust bearing202.断裂break203.液压hydraulic pressure204.混合润滑mixed lubrication205.渐开线花键involute spline206.焊接welding207.球形阀globe valve208.球墨铸铁nodular cast iron209.粗糙度roughness210.铜合金copper alloy211.铝合金aluminum alloy212.铰链hinge213.黄铜brass214.剩余预紧力residual initial tightening load215.喷丸sand blast216.强度strength217.强度极限ultimate strength218.最小油膜厚度minimum film thickness219.棘轮传动ratchet wheel220.滑动轴承sliding bearing221.滑块slide block222.滑键slide key223硬度hardness224.联轴器coupling225.装配assembly226.铸件casting227.铸钢cast steel228.铸造cast229.铸铁cast iron230.铸铝cast aluminum231.链chain232.链轮chain wheel233.销pin234.销钉联接pin connection235.塑性材料ductile material236.塑性变形plastic deformation 237.塑料plastics238.摇杆rocker239.楔键wedge key240.滚动体Rolling Body241.滚动轴承rolling bearing242.滚压rolling243.滚珠丝杆ball leading screw 244.锡青铜tin bronze245.锥形阀cone valve246.键key247.键槽keyways248.碳化carbonization249.碳素钢carbon steel250.稳定性stability251.腐蚀corrosion252.锻件forged piece253.锻钢forged steel254.锻造forging255.静压轴承hydrostatic bearing 256.静应力steady stress257.静载荷／应力static load／stress 258.摩擦friction259.摩擦力friction force260.摩擦功friction work261.摩擦系数friction coefficient 262.摩擦角friction angle263.摩擦学tribology264.槽轮sheave wheel265.橡胶rubber266.箱体box267.磨削grinding268.磨损wear269.磨损过程wear process270.螺母nut271.螺纹screw272.螺纹threads273.螺纹联接threaded and coupled 274.螺钉pitch275.螺栓bolt276.螺栓联接bolting277.螺旋传动screw-driven机械设计名词术语中英对照机械设计名词术语中英文对照表Chinese English阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross 槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum《机械设计基础》常用单词中英文对照寿命life应力stress应力集中stress concentration应变strain扭转torsion扭转角angle of torsion抗压强度compression strength抗拉强度tensile strength抗弯强度bending strength材料material极限应力limit stress极惯性矩polar moment of inertial花键spline连杆connecting rod周转轮系epicyclic gear train屈服强度yield strength底板base plate底座underframe径向力radial force径向当量动载荷radial equivalent dynamic load 径向轴承journal bearing径向基本额定动载荷radial elementary rated life 性能performance承载量load carrying capacity拉力pulling force拉伸tension拉伸应力tensile stress油膜oil film泊松比Poisson’s ratio直径diameter空心轴hollow axle空气轴承air bearing表面处理surface treatment表面淬火surface quenching转矩torque金属材料metallic material青铜合金bronze alloy非金属材料non metallic material齿轮gear齿轮模数module of gear teeth齿数tooth number保持架holding frame变应力dynamic stress变形deflection, deformation变载荷dynamic load。