TKICO去耦合器技术规格书
去耦合器使用说明书
固态去耦合器使用说明书遵循标准NFPA70 250-6（e）《国家电气规程》；IEC61643.1 《连接低压配电系统的电涌保护器第1 部分：性能要求和试验方法》；NACE SP0177 《减轻交流电和雷电对金属构筑物和腐蚀控制系统影响的措施》；GB/T2423.1 《电工电子产品环境试验第2 部分：试验方法试验A：低温试验》；GB/T2423.2 《电工电子产品环境试验第2 部分：试验方法试验B：高温试验》；GB/T2423.3 《电工电子产品环境试验第2 部分：试验方法试验 C：恒定湿热试验》；GB/T2423.5 《电工电子产品环境试验第2 部分：试验方法试验Ea 和导则：冲击》；GB/T2423.10 《电工电子产品环境试验第2 部分：试验方法试验FC 和导则：振动（正弦）》GB11032 《交流无间隙金属氧化物避雷器》；GB4208 《外壳防护等级（IP 代码）》；GB 18802.1-2002/IEC 61643-1《低压配电系统的电涌保护器（SPD）第1 部分：性能要求和试验方法》；SY/T0032 《埋地钢制管道交流排流保护技术标准》应用范围固态去耦合器可用于：●管道电位梯度垫(接地垫)的去耦合。
●对设备进行过交流故障、雷电和开关暂态过程的过电压保护●为了安全，用于不同的金属间的去耦合，这些会属在某些情况下会有交流耦合。
●在阴极保护系统中，电气设备的交流接地和直流隔离。
●消减交流感应电压。
在去耦合不同的金属时，固态去耦合器可用于两个接地系统之间，或应用在其它需要交流搭接的构筑物之间，同时防止这些构筑物之间的电偶腐蚀。
性能参数隔离电压当电压低于所选定的隔离电压时，固态去耦合器阻断直流电流流通，而允许交流电流通过。
当电压高于所选定的隔离电压时，固态去耦合器成为一个双向导电装置，允许所有的电流通过，以限制构筑物上的电压。
直流泄漏电流与隔离电压的关系正常情况下，20℃时各种型号的固态去耦合器在最大隔离电压下的直流泄漏电流均小于10mA，70℃时小于100mA，正常的阴极保护电压作用在固态去耦合器上时，在两种温度条件下的漏电电流通常都小于1mA，这个数值对于阴极保护系统来说，是微不足道的。
固态去耦合器技术规格书
3.2 投标承诺 3.3.1 供货商职责
供货商应对固态去耦合器及其配套产品的设计、材料采购、工件的制造、零部件的组装、 图纸、资料的提供和检验以及在不同场所进行的试验负有完全责任。供货商还应对固态去耦 合器及其配套产品的性能、总体装配质量、运输负责，并指导现场安装。
技术规格书
防腐 版次 Rev
0
设计阶段
Stage
图号
Drawing No.
第 3页 Sheet
施工图
H951 -JS-F -04
共 13 页 of
1 范围
第一部分基本要求
本技术规格书规定了固态去耦合器性能、材料、测试、检验、运输和验收等方面的最低 要求。
本技术规格书适用于油气储运工程项目用固态去耦合器及附件的采购。
GB/T2423.1
电工电子产品环境试验 第 2 部分：试验方法 试验 A： 低温
GB/T2423.2
电工电子产品环境试验 第 2 部分：试验方法 试验 B： 高温
GB/T2423.3
电工电子产品环境试验 第 2 部分： 试验方法 试验 Cab： 恒定
湿热方法
GB3836.1
爆炸性环境第 1 部分：设备 通用要求
技术规格书
防腐 版次 Rev
0
设计阶段
Stage
图号
Drawing No.
第 4页 Sheet
施工图
H951 -JS-F -04
共 13 页 of
3 总体要求
3.1 供货商资质要求 3.1.1 供货商证书要求
供货商及分包商应具有中华人民共和国或相应国际认证机构颁发的有效 ISO14001 环境 管理体系认证证书、ISO9001 质量体系认证证书。或相应的 CE、UL 或 ETL 产品认证证书。 3.1.2 供货商业绩和经验要求
韩国电子品牌 'OPTO-ELECTRONIC' 的817A型号光电耦合器说明书
Dimensions: [mm]121Scale - 3:1Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 174638 Waldenburg Germany140817140110Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive Solutions140817140110 Max-Eyth-Str. 174638 WaldenburgGermanyTotal Power Dissipation vs. Ambient Temperature:20406080100120140160-55-35-15525456585105125IR-diode -I F(mA)Ambient Temperature (°C)Phototransistor-PO(mW)CollectorPowerDissipation(mW)ForwardCurrent(mA)Collector Dark Current vs. Ambient Temperature:11010010001000025456585105125CollectorDarkCurrent(nA)Ambient Temperature (°C)V CE= 20VV CE= 10VNote: measured with Bin BWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODSaVo001.0052023-08-22DIN ISO 2768-1mDESCRIPTIONWL-OCPT OptocouplerPhototransistor ORDER CODE140817140110SIZE/TYPE BUSINESS UNIT STATUS PAGEAbsolute CTR vs. Ambient Temperature50100150200250300-60-40-20020406080100120AbsoluteCTRAmbient Temperature (°C)V CE= 5VV CE= 0,4VTestcondition: I F=5mA, T A=25°C, Bin BRelative CTR vs. Ambient Temperature:0,40,60,811,21,4-60-40-20020406080100120RelativeCTRAmbient Temperature (°C)V CE= 5VV CE= 0,4VTestcondition: I F=5mA, Normalized to T A=25°C, Bin BWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODSaVo001.0052023-08-22DIN ISO 2768-1mDESCRIPTIONWL-OCPT OptocouplerPhototransistor ORDER CODE140817140110SIZE/TYPE BUSINESS UNIT STATUS PAGEWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive Solutions140817140110 Max-Eyth-Str. 174638 WaldenburgGermanyWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive Solutions140817140110 Max-Eyth-Str. 174638 WaldenburgGermany050100150200250300350400450A b s o l u t e C T R (%)Testcondition T A Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 174638 Waldenburg Germany140817140110050100150200250300A b s o l u t e C T R (%)Testcondition T A Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 174638 Waldenburg Germany1408171401100102030R e s p o n s e T i m e (µs )Testcondition I C Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 174638 Waldenburg Germany140817140110Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive Solutions140817140110 Max-Eyth-Str. 174638 WaldenburgGermanyWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive Solutions140817140110 Max-Eyth-Str. 174638 WaldenburgGermanyT e m p e r a t u r eT T T Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 174638 Waldenburg Germany140817140110Cautions and Warnings:The following conditions apply to all goods within the product series of Optoelectronic Components of Würth Elektronik eiSos GmbH & Co. KG:General:•This optoelectronic component is designed and manufactured for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control,ship control), transportation signal, disaster prevention, medical, public information network, etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Optoelectronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. •The optoelectronic component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved. •Do not drop or impact the components, the component may be damaged•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products also apply to customer specific products.•Unless Würth Elektroik has given its express consent, the customer is under no circumstances entitled to reverse engineer, disassemble or otherwise attempt to extract knowledge or design information from the optoelectronic component.Product specific:Soldering:•The solder profile must comply with the technical product specifications. All other profiles will void the warranty. •All other soldering methods are at the customers’ own risk•The soldering pad pattern shown above is a general recommendation for the easy assembly of optoelectronic components. If a high degree of precision is required for the selected application (i.e. high density assembly), the customer must ensure that the soldering pad pattern is optimized accordingly.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the optoelectronic component body, marking or plating. Washing agents may have a negative effect on the long-term functionality of the product.• Using a brush during the cleaning process may break the optoelectronic component body. Therefore, we do not recommend using a brush during the PCB cleaning process.Potting:•If the product is potted in the customer application, the potting material might shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the optoelectronic component body, pins or termination. Expansion could damage the components. We recommend a manual inspection after potting to avoid these effects.Storage Conditions:• A storage of Würth Elektronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the optoelectronic component to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•For a moisture sensitive component, the storage condition in the original packaging is defined according to IPC/JEDEC-J-STD-033. It is also recommended to return the optoelectronic component to the original moisture proof bag and reseal the moisture proof bag again. •The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components.Packaging:•The packaging specifications apply only to purchase orders comprising whole packaging units. If the ordered quantity exceeds or is lower than the specified packaging unit, packaging in accordance with the packaging specifications cannot be ensured.Handling:•Violation of the technical product specifications such as exceeding the nominal rated current, will void the warranty. •The product design may influence the automatic optical inspection.•Certain optoelectronic component surfaces consist of soft material. Pressure on the top surface has to be handled carefully to prevent negative influence to the function and reliability of the optoelectronic components.•ESD prevention methods need to be applied for manual handling and processing by machinery. •Resistors for protection are obligatory.•In addition to optoelectronic components testing, products incorporating these devices have to comply with the safety precautions given in IEC 60825-1, IEC 62471 and IEC 62778.Technical specification:•The typical and/or calculated values and graphics of technical parameters can only reflect statistical figures. The actual parameters ofeach single product, may differ from the typical and/or calculated values or the typical characteristic line.Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 174638 Waldenburg GermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCEPROJECTION METHODSaVo001.0052023-08-22DIN ISO 2768-1mDESCRIPTIONWL-OCPT Optocoupler PhototransistorORDER CODE140817140110SIZE/TYPEBUSINESS UNITSTATUSPAGE•In the characteristics curves, all values given in dotted lines may show a higher deviation than the paramters mentioned above. •On each reel, only one bin is sorted and taped. The bin is defined on the current transfer ratio.•In order to ensure highest availability, the reel binning of standard deliveries can vary. A single bin cannot be ordered. Please contact us in advance, if you need a particular bin sorting before placing your order.•These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable. However, no responsibility is assumed for inaccuracies or incompleteness.The customer has the sole responsibility to ensure that he uses the latest version of this datasheet, which is available on Würth Elektronik’s homepage. Unless otherwise agreed in writing (i.e. customer specific specification), changes to the content of this datasheet may occurwithout notice, provided that the changes do not have a significant effect on the usability of the optoelectronic components.Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 174638 Waldenburg GermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCEPROJECTION METHODSaVo001.0052023-08-22DIN ISO 2768-1mDESCRIPTIONWL-OCPT Optocoupler PhototransistorORDER CODE140817140110SIZE/TYPEBUSINESS UNITSTATUSPAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODSaVo001.0052023-08-22DIN ISO 2768-1mDESCRIPTIONWL-OCPT OptocouplerPhototransistor ORDER CODE140817140110SIZE/TYPE BUSINESS UNIT STATUS PAGE。
CK Switches KSC系列液体氮触摸开关数据手册说明书
T a c t i l e S w i t c h esKSC SeriesSealed Tact Switch for SMTFeatures/Benefits• Positive tactile feeling • J or G terminations • Various heights • IP67SpecificationFUNCTION: Momentary actionCONTACT ARRANGEMENT: 1 make contact = SPST, N.O.TERMINALS: J bend & Gullwing type for SMT SEALING: IP67 except KSC5 (IP50)Liability LimitationThis datasheet does not provide enough information forapplications that require a certain level of quality or safety such as automotive, medical systems, or safety equipement. Please contact customer service for the contractual specification package.EnvironmentalSilver Gold OPERATING TEMPERATURE: -40˚C to 85˚C -40˚C to 125˚C STORAGE TEMPERATURE:-55˚C to 85˚C-55˚C to 125˚CProcessSOLDERING: Depending on the application, this component issuited to the following methods:– Terminals being silver or gold plated over a nickel barrier, the use of slightly activated flux is suitable.– Soldering on double wave machine for vertical versions: soldering time ≤ 5 sec.– Cleaning according to typical washing processes.– Lead free reflow soldering process in accordance with IEC61760-1.Typical Applications • Automotive• Medical instruments • Industrial electronics• Network infrastructure and IT • ElevatorElectricalSilver Gold MAXIMUM POWER: 1 VA 0.2 VA MAXIMUM VOLTAGE: 32 VDC 32 VDC MINIMUM VOLTAGE: 20 mV 20 mV MAXIMUM CURRENT: 50 mA 10 mA MINIMUM CURRENT:1 mA*0.1 mADIELECTRIC STRENGTH (50 Hz, 1 min.): ≥ 250 Vrms CONTACT RESISTANCE: ≤ 100mΩINSULATION RESISTANCE (100 V): ≥ 10M ΩBOUNCE TIME: ≤ 1 ms* Ultra low current with 10 µA - 1 VDC version are available upon request for KSC2 and KSC4PackagingTape and Reel (see series for quantity information)NOTE: Specifications listed above are for switches with standard options.Note: KSC Series is subject to variants. Please contact customer service for other options.Tactile SwitchesKSC SeriesSealed Tact Switch for SMTJ J BENDG GULLWINGTactile SwitchesKSC XA SeriesSoft Sound Tact SwitchHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.For any part number different from those listed above, please consult your local representative.Features/Benefits • New soft sound • Extended cage • IP67• Long life• J terminations • Tape & reelTypical Applications• Automotive interior & openings(gear shift paddle, steering wheel, window lifter, seat adjustment modules, trunk & door handle modules)• Medical & industrial electronics (front panel, instrumentation)T a c t i l e S w i t c h esKSC SLT SeriesLong Travel Tact SwitchHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.For any part number different from those listed above, please consult your local representative.Features/Benefits • Long travel • Soft sound • IP40• J & G terminations • Tape & reelTypical Applications • Automotive interior • Front panel• InstrumentationTypeForce (N)Life (cycles)Travel (mm)KSC SLT 221J LFS 2.4 +/- 0.7200,000 1.35 +/-0.25KSC SLT 221G LFS 2.4 +/- 0.7200,000 1.35 +/-0.25KSC SLT 223J LFG 2.4 +/- 0.7 200,000 1.35 +/-0.25KSC SLT 223G LFG 2.4 +/- 0.7200,000 1.35 +/-0.25KSC SLT 241J LFS 3.5 +/- 0.9200,000 1.35 +/-0.25KSC SLT 241G LFS 3.5 +/- 0.9200,000 1.35 +/-0.25KSC SLT 243J LFG 3.5 +/- 0.9200,000 1.35 +/-0.25KSC SLT 243G LFG3.5 +/- 0.9200,0001.35 +/-0.25SpecificationFUNCTION: MomentaryCONTACT ARRANGEMENT: 1 make contact = SPST, N.O.TERMINALS: J bend & Gullwing type for SMTMechanicalMAXIMUM APPLIED FORCE: 40N* VALID ONE TIME. MAXIMUM ALLOWED TRAVEL TO AVOIDOVERLOAD ISSUES IS 1.70MM.ElectricalSWITCHING POWER MAX.: 1.0 VA 0.2 VAMAXIMUM POWER: 1.0 VA 0.2 VA MAXIMUM VOLTAGE: 32 VDC 32 VDC MINIMUM VOLTAGE: 20 mV 20 mV MAXIMUM CURRENT: 50 mA 10 mA MINIMUM CURRENT:1 mA1 mADIELECTRIC STRENGTH: ≥ 250 Vrms CONTACT RESISTANCE: < 100mΩINSULATION RESISTANCE: Initial measurement: ≥ 1GΩ After damp heat: ≥10MΩBOUNCE TIME: < 5 msEnvironmentalOPERATING TEMPERATURE: -40°C to +85°C (Silver) -40°C to +125°C (Gold)STORAGE TEMPERATURE: -40°C to +85°C (Silver) -40°C to +125°C (Gold)ProcessCompatible with the lead free reflow soldering process.PackagingIn reels of 1,000 pieces.Dimensions of reels according to EIA RS481 or IEC 2863.External diameter 330 mm ± 2 mm.2 2.4 N 4 3.5 NActuator2 Soft Silver GoldTactile SwitchesKSC SLT SeriesLong Travel Tact SwitchJ J BendG Gullwing6,2+0,36,2+0,30,70,0540,10,1+0,20,12,70,15+0,3-0,13,3 mini6,8+0,3-0,12,8 m a xLAYOUT - PADSCALE : 5**6,2+0,36,2+0,30,70,0540,10,1+0,20,12,70,15+0,3-0,1( 0,5 )( 15 )7,6+0,2-0,1100,32,8 m a x5LAYOUT - PAD SCALE : 5**TAPE & REEL400,330,03SECTION B-BSECTION A-A0,1T a c t i l e S w i t c h esKSC1 SeriesSealed Tact Switch for SMT+0,36,2 0+0,36,2 0+0,20,1 02,9 ma xø 21,5 m i n4˚ maxR 0,2smooth surfaceHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.However, please note that all the combinations of these options are not feasible.For any part number different from those listed above, please consult your local representative.Termination JJ bend G GullwingKSC1 without actuator 2,5 mm highPackagingSwitches delivered on continuous tape & reels of 2,000 pieces Dimensions according to EIA RS-481/ IEC 60286-3 standard External diameter 330 ± 2 mmTactile SwitchesKSC2 SeriesSealed Tact Switch for SMTHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.However, please note that all the combinations of these options are not feasible.For any part number different from those listed above, please consult your local representative.KSC2 soft actuator 3,5 mm highPackagingSwitches delivered on continuous tape & reels of 2,000 pieces Dimensions according to EIA RS-481/ IEC 60286-3 standard External diameter 330 ± 2 mmT a c t i l e S w i t c h esKSC3 SeriesSealed Tact Switch for SMTHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.However, please note that all the combinations of these options are not feasible.For any part number different from those listed above, please consult your local representative.Termination J J bend GGullwingKSC3 hard actuator 3,5 mm highPackagingSwitches delivered on continuous tape & reels of 2,000 pieces Dimensions according to EIA RS-481/ IEC 60286-3 standard External diameter 330 ± 2 mmTactile SwitchesKSC4 SeriesSealed Tact Switch for SMTHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.However, please note that all the combinations of these options are not feasible.For any part number different from those listed above, please consult your local representative.KSC4 soft actuator 5,2 mm highPackagingSwitches delivered on continuous tape & reels of 1,000 pieces Dimensions according to EIA RS-481/ IEC 60286-3 standard External diameter 330 ± 2 mmT a c t i l e S w i t c h esHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, selectdesired option from each category and place it in the appropriate box.For any part number different from those listed above, please consult your local representative.• SPDT NC-NO function • Silicone actuator • J or G terminations • Tape & reel • IP67PackagingIn reels of 1,000 pieces.Dimensions of reels according to EIA RS481 or IEC 2863.External diameter 330 ± 2 mm PCB LayoutTypical Applications • Automotive• Medical equipment • Industrial electronicsTypeForce (N)Operating Life (operations)Travel (mm)KSC441J DCT 70SH LFS 4.75 +/-1.25300,0000.85+0.35/-0.25KSC441G DCT 70SH LFS 4.75 +/-1.25300,0000.85+0.35/-0.2540,16,206,86,2 00,70,053,3 mini0,10 02,9 m a x5,20,22,70,10,850,05414312Visual poka yoke CSCALE 5LAYOUT - PADSCALE : 51 -2 NC 1 -3 NOHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, selectdesired option from each category and place it in the appropriate box.For any part number different from those listed above, please consult your local representative.Features/Benefits • • • • • TypeForce (N)Operating Life (operations)KSC421G 70SH LFS PF 1.8+/-0.45300,000KSC421J 70SH LFS PF 1.8+/-0.45300,000KSC422G 70SH LFS PF 1.8+/-0.451,000,000KSC422J 70SH LFS PF 1.8+/-0.451,000,000KSC441G 70SH LFS PF 4 +/- 1300,0004 +/- 1300,000KSC442G 70SH LFS PF 4 +/- 11,000,0004 +/- 11,000,000KSC461G 70SH LFS PF 6.25+/- 1.75300,0006.25+/- 1.75300,000T a c t i l e S w i t c h esHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, selectdesired option from each category and place it in the appropriate box.For any part number different from those listed above, please consult your local representative.Features/Benefits• Extended cage for mechanical stop • Silicone actuator • J termination • Tape & reel • IP67- Life time is 300,000 cycles at 20N actuation force- The extended cage can be used as mechanical stop for the activationbutton- Overload value reaches 200N (one time)PackagingIn reels of 1,000 piecesDimensions of reels according to EIA RS481 or IEC 2863External diameter 330 ± 2 mmTypical Applications • Industrial electronics • Consumer• Medical equipment • Automotive interiorTypeForce (N)Life Travel (mm)KSC421J 70SH LFS OF 1.65+/-0.45300,0000.5+/-0.25KSC441J 70SH LFS OF4.0+/-1.0300,0000.65+0.3/-0.26,2+0,3 06,2+0,30,70,0540,13,9 m a x0,14,7250,12,50,13,3 mini6,8+0,3-0,15,10,2**1How To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, selectdesired option from each category and place it in the appropriate box.For any part number different from those listed above, please consult your local representative.• Silicone actuator• J terminations • Tape & reel • IP67Type Force (N)KSC2 TE 01J LFS 1.60 ±0.6KSC2 TE 31J LFS 2.80 ±0.7KSC2 TE 41J LFS4.00 ±1.0T a c t i l e S w i t c h esHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, selectdesired option from each category and place it in the appropriate box.For any part number different from those listed above, please consult your local representative.• Silicone actuator • J terminations • Tape & reel • IP67• Game controllers/ Drones • Industrial applications • Medical applicationsTactile SwitchesKSC5 SeriesTact Switch with Rocker Option for SMTHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.However, please note that all the combinations of these options are not feasible.For any part number different from those listed above, please consult your local representative.Termination J J bend G GullwingKSC5 hard actuator 5,6 mm highT a c t i l e S w i t c h esKSC6 SeriesSealed Tact Switch for SMT+0,36,2 0+0,36,2 02,9 m a x+0,20,1 01,6ø 4,7ø 2,97,7How To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.However, please note that all the combinations of these options are not feasible.For any part number different from those listed above, please consult your local representative.Termination J J bend G GullwingKSC6 hard actuator 7,7 mm highPackagingSwitches delivered on continuous tape & reels of 950 pieces Dimensions according to EIA RS-481/ IEC 60286-3 standard External diameter 380 ± 2 mmTactile SwitchesKSC7 SeriesSealed Tact Switch for SMTHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.However, please note that all the combinations of these options are not feasible.For any part number different from those listed above, please consult your local representative.Termination J J bend G GullwingKSC7 soft actuator 4,4 mm highPackagingSwitches delivered on continuous tape & reels of 1,000 pieces Dimensions according to EIA RS-481/ IEC 60286-3 standard External diameter 330 ± 2 mmT a c t i l e S w i t c h esKSC8 SeriesSealed Tact Switch for SMT1,15ø 2,96ø 4,7+0,36,2 0+0,36,2 02,9 m a x 4,9+0,20,1 0How To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.However, please note that all the combinations of these options are not feasible.For any part number different from those listed above, please consult your local representative.KSC8 hard actuator 4,9 mm highPackagingSwitches delivered on continuous tape & reels of 1,000 pieces Dimensions according to EIA RS-481/ IEC 60286-3 standard External diameter 330 ± 2 mmTactile SwitchesHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.For any part number different from those listed above, please consult your local representative.Color20 Light grey 40 Red 80 White 90 BlackKSC9 SeriesSealed Tact Switches for SMTKSC9 hard actuator 7,7 mm highPackagingSwitches delivered on continuous tape & reels of 950 pieces Dimensions according to EIA RS-481/ IEC 60286-3 standard External diameter 380 ± 2 mmR0,2510,2±0,1ø 6,35ø 615,4±0,4SWITCH WITH CAPT a c t i l e S w i t c h esKSC10 SeriesSealed Tact Switches for SMTHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.However, please note that all the combinations of these options are not feasible.For any part number different from those listed above, please consult your local representative.Termination J J bend G GullwingKSC10 soft actuator 4,9 mm highPackagingSwitches delivered on continuous tape & reels of 1,000 pieces Dimensions according to EIA RS-481/ IEC 60286-3 standard External diameter 330 ± 2 mmNote: KSC10 offered with yellow actuator as standard, hardness 55 Shore+0,3B–95Dimensions are shown: mmSpecifications and dimensions subject to changeTactile Switches26 May 22KSC11 SeriesSealed Tact Switch for SMTHow To OrderOur easy build-a-switch concept allows you to mix and match options to create the switch you need. To order, select desired option from each category and place it in the appropriate box.For any part number different from those listed above, please consult your local representative.Features/Benefits • Hard actuator • Long life• Positive tactile feeling • IP67 sealed • SMTElectricalMAXIMUM POWER: 1 VAMIN. / MAX. VOLTAGE: 0.02V / 32V MIN. / MAX. CURRENT: 1 mA / 50 mA DIELECTRIC STRENGTH: 250 Vrms CONTACT RESISTANCE: ≤ 100 mΩINSULATION RESISTANCE: (100V): 1000 MΩBOUNCE TIME: ≤ 5 msSolderingThis component is suited to the following methods:– Cleaning according to typical washing processes– Lead free reflow soldering process in accordance with IEC 61760-1PackagingIn reels of 1,700 piecesWidth of carrier tape: 16 mm Dimensions of reels: 380 mmTypical Applications • Gaming/ Drones • Industrial •Medical• High-end consumer • AvionicsN E WT a c t i l e S w i t c h esB–96Dimensions are shown: mmSpecifications and dimensions subject to changeN EW26 May 22KSC11 SeriesSealed Tact Switch for SMT6,2+0,36,2+0,30,70,0540,16,8+0,3-0,1LAYOUT - PAD**。
品牌C.K的电子塑料切割器产品说明书
C.K ECOTRONIC ESD - PRECISION SIDE CUTTERS
Item No. Description
A B CDE
Length Weight (mm) (g)
T3883 ESD Side Cutters – Micro 8 9.5 16 4 21 132
64
Blade Thickness (mm)
2
Blade Height at Tips (mm)
1.5
T3884
ESD Side Cutters - Micro, Reverse Cut
8
9.5 13 4 48
132
64
2
1.5
T3885 ESD Side Cutters - Slim
9 10 18 5 21 139
76
2.5
1.5
T3886
AB C D
E
mm mm mm mm mm
T3889 ESD Long Snipe Nose Pliers 49 12 6 1
2
T3890 ESD Short Snipe Nose Pliers 31 12 6 1 1.5
T3891 ESD Flat Nose Pliers3
31
3
2
T3892 ESD Snipe Nose Pliers (Bent) 39 12 6 1
• Special tool steel body, hardened for long-term performance
• Black oxidised finish for corrosion resistance and reduced glare
• Electro-static discharging handles - dissipative
特克ト尼克560系列CRT定格器电容法标准化器说明书
Q
T y
DESCRIPTION
1 CONNECTORc, oaxial, l contact, BNC, w/mounting hardware
1 KNOB, plug-in securing 1 FASTENER, pawl right w/stop - mounting hardware: (not included w/fastener) 2 LOCKWASHERin, ternal, #4 2 NUT, hex., 4-40 x 3/16 inch
11
211-0507-00
PLATE, sub-panel 1 CHASSIS - mounting hardware: (not included w/chassis) 3 SCREW,6-32 x 5/16 inch, 1000 csk, FHS 3 SCREW,6-32 x 5/16 inch, PHS
C760 to obtain this value of C3.
--.....
A 2
PIN 17 PIN 21
TYPE 067-0500-00
Step 3. ADJUSTC760 OF THE 561A FOR CORRECTEFFECTIVEDEFLECTIONPLATE CAPACITANCE. (For C760 between pin 21 and gnd)
TK-使用说明书
第一节概述TK200井下通讯、控制、保护系统是在我厂TK100工作面及皮带通讯、控制一体化系统基础上，重新开发研制的新一代产品。
可实现工作面、顺槽皮带、大皮带等的保护，控制、沿线通话、故障检测、显示及报警等功能。
从工作面到顺槽，从单条运输皮带到整个矿井的所有固定皮带，从简单的皮带头尾搭接到“丁”字型、“山”字型搭接，从设备启、停控制到工作电流、电压显示、皮带速度检测和显示、煤仓煤位检测、显示、高低煤位停机，油温、油压、轴温等的检测和显示及计算机远程通信，故障自诊断等等，TK200均可提供全套解决方案。
（一）系统组成：TK200由以下设备及子系统构成：1．TK200控制、显示中心2．拉线急停、沿线闭锁、通话子系统。
3．智能输入、输出（用于远距离输入、输出）。
4．智能耦合器5．皮带控制器(待开发)6．皮带张紧（可由参数设置为自动张紧、手动张紧、朗艾道自动张紧等）7．传感器子系统（二）系统功能：TK200系统可完成：1．工作面各设备的启停状态检测和显示。
包括：（1）采煤机、前后部运输机、破碎机、转载机、泵、皮带的启停等。
（2）配接我厂的“TJ100设备工作电流检测仪”后，可对以上设备的工作电流进行检测、显示及过载后进行语言报警。
2．检测结果的显示控制计算机对以上参数检测后，在TK200控制中心的10.4”大屏幕彩色液晶平板显示器上显示出来。
（以图形、动画的形式显示设备启停情况，以不同的颜色表示过载情况。
）3．设备启停时间统计、显示。
4．设备启停控制。
通过按键，可对破碎、转载、前后部运输机及泵等设备进行启停控制。
5．报警设备启动前，以及发生各种故障时进行报警，报警时间的长短可以通过参数设定。
6．将工作面各设备工作状态和参数传输给井上，在井上计算机进行显示。
7．皮带控制包括六大保护，皮带启停、皮带张紧（可由参数设置为自动张紧、手动张紧或朗艾道型自动张紧）、软启动控制、电机温度检测和显示、皮带沿线拉线闭锁。
琪基电子 1004-1000 型号高频耦合器数据手册说明书
Dimensions: [mm]MPPP010473J630DCPP55004890303323004CSMPPP010473J630DCPP55004 890303323004CSMPPP010473J630DCPP55004 890303323004CSMPPP010473J630DCPP55004 890303323004CST e m p e r a t u r eT T T MPPP010473J630DCPP55004890303323004CSCautions and Warnings:The following conditions apply to all goods within the product series of WCAP-FTBP of Würth Elektronik eiSos GmbH & Co. KG:1. General:The capacitor is engineered, designed and manufactured to be used within the datasheet specified values. Do not use the capacitor neither short term nor long term outside the specified values, which are given in the data sheet.2. Product specific:Follow all instructions mentioned in the data sheet, especially:•The soldering profile has to be complied with according to the technical reflow soldering specification, otherwise this will void the warranty.•Wave soldering is only allowed after evaluation and approval.•Do not exceed the lower and/ or upper specified temperature!•Do not use the capacitor with other than specified voltage!•Prevent any kind of mechanical stress to the capacitor terminals!•Do not use the soldered capacitor on a PCB for any movement or transportation to avoid any tensile force to the capacitor!•Do not apply any kind of flexural or compressive force onto soldered or unsoldered component!•Prevent the capacitor surface from any damage or scratches with sharp edges (e.g. chassis, screwdrivers, pincers).•The capacitor must be placed on a PCB while using the recommended drill hole pattern without changing of the specific lead pitch!•Avoid any other than specified temperature and / or time conditions during soldering!•Avoid any overload or conditions that are not specified in the capacitors datasheet!•Avoid any water or heavy dust on capacitors surface which may cause electrical leakage, damage, overheating or corrosion!3. Storage conditions:These film capacitors must be stored in stable climatic conditions, which are listed within the general information on front of data sheet. 4. Storage duration:All products shall be used before the end of the period of 12 months based on the product date code, if not a 100% solderability can´t be ensured.5. Flammability:Avoid any external energy or open fire (passive flammability).6. Vibration resistance:Do not exceed the vibration limits given by IEC60068-2-6.7. Cleaning:Do not use any other cleaning solvents for box-typed capacitors except: ethanol, isopropanol, n-propanol - water mixtures. After cleaning a drying process with temperatures not exceeding 65°C and not longer than 4 hours is mandatory to prevent any kind of electrical damage.8. Full covered or embedded capacitors in final applications:If final assemblies will be placed completely in any plastic resin, physical, chemical and thermal influences must be considered. If any specific evaluation or test is necessary please contact the related Würth Elektronik Capacitor Business Division.Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0*******************CREATED CHECKED GENERAL TOLERANCE PROJECTIONMETHODKaS PSL DIN ISO 2768-1mDESCRIPTION TECHNICAL REFERENCEWCAP-FTBP Film Capacitors MPPP010473J630DCPP55004ORDER CODE890303323004CSSIZE REVISION STATUS DATE (YYYY-MM-DD)BUSINESS UNIT PAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0*******************CREATED CHECKED GENERAL TOLERANCE PROJECTIONMETHODKaS PSL DIN ISO 2768-1mDESCRIPTION TECHNICAL REFERENCEWCAP-FTBP Film Capacitors MPPP010473J630DCPP55004ORDER CODE890303323004CSSIZE REVISION STATUS DATE (YYYY-MM-DD)BUSINESS UNIT PAGE。
迈克斯 PicoBlade 连接器系统产品说明书
Documents: Drawing (PDF) 3D Model (PDF) 3D Model Product Specification PS-51021-010-001 (PDF)
Application Specification 510210000-AS-000 (PDF) Packaging Specification SPK-53047-001-001 (PDF) RoHS Certificate of Compliance (PDF)
Part Number:
Status:
Overview: Description:
This document was generated on 02/21/2020
PLEASE CHECK FOR LATEST PART INFORMATION
0530471110 Active
EU ELV Not Relevant
EU RoHS
China RoHS
Compliant
REACH SVHC
Not Contained Per -
ECHA_01_2020 (16
January 2020
Halogen-Free
Status
Not Low-Halogen
For more information, please visit Contact US
贴片光电耦合器简介及应用
光电耦合器(以下简称光耦)是一种发光器件和光敬器件组成的光电器件。
它能实现电一光一电信号的变换，并且输入信号与输出信号是隔离的。
U前极大多数的光耦输入部分采用神化镣红外发光二极管，输出部分釆用硅光电二极管、硅光电三极管及光触发可控硅。
这是因为峰值波长900~940nm的神化稼红外发光二极簣能与硅光电器件的响应峰值波长相吻合，可获得较高的信号传输效率.光耦的结构光耦的内部结构(剖面)如图1所示。
光耦输入部分大都是红外发光二输岀部分有不同的光敬器件，如图2所示。
光敏器件管心塑料封装外喘发光簷管心透明硅胶电极引脚这里要说明的是，图2 (c)的输入部分有两个背对背的红外发光二管,它用于交流输入的场合；图2 (d)采用达林顿输出结构，它可使输出获得较大的电流；图2 (e)、2(f)的输出山光触发双向可控硅组成，它们主要用来驱动交流负载。
图2(e)与图2 (f)的差别是图2(f)有过零触发控制(图中的“ZC”即“过零”的意思)，而图2(e)没有过零触发控制电路。
基本电路光耦的基本电路如图3所示•图3 (a)的负载电阻RL接在发射极及地之间，图3 (b)的负载电阻RL接在电源Vdd与集电极之间.在图3 (R中，输入端加上Vcc电压，经限流电阻Rin后,有一定的电流IF 流经红外发光二极管，IF与Vcc、发光二极管的正向压降VF及Rin的关系为:I F二(Vcc-VF)/Rin。
式中的VF取1。
3V« IF的最大值由资料给出(一般工作时IF WlOmA)・发光二极管发光后,光电三极管导通，集电极电流Ic III Vdd经光电三极管流过RL到地，使输出电压Vout=IcXRL(或Vout二Vdd—VCE, VCE为光电三极管的管压降)。
图3(b)的工作原理与图3 (a)相同，不再重复。
图3中输入、输出也可用各自的地。
从图3 (a)可以看出；输入端不加Vcc电压，输岀端Vout=0V,输入端加了V CC 电压，负载得电，这个功能相当于“继电器”。
Victaulic 系列 - 减径器说明书
Concentric/Eccentric Reducer No. 50 ConcentricNo. 51 EccentricNo. 50No. 51Fabricated SteelNo. 50Fabricated SteelNo. 51Size No. 50 ConcentricReducer No. 51 Eccentric ReducerNominal Size E to EApprox.Weight Each E to EApprox.Weight Eachinches mm inchesmmlbs.kginchesmmlbs.kg11/432x 3/420+1.90.9——125+1.90.9——11/240 x 3/420+1.40.6——1252.50640.80.48.50 (sw)2164.52.0 11/4322.50641.00.5——250 x 3/4202.50640.90.39.00 (sw)2292.00.91252.50640.70.39.00 (sw)2292.31.0 11/4322.50641.20.59.00 (sw)2294.62.1 11/2403.50891.00.53.50891.10.521/265x 3/420+1.30.6+3.31.51252.50641.10.59.502413.51.6 11/4323.50893.31.53.50891.40.6 11/2402.50643.61.69.50 (sw)2413.71.72502.50643.91.83.50894.32.0380x 3/420+1.50.7+4.52.01252.50641.30.69.50 (sw)2414.82.2 11/4322.50641.40.6+4.82.2 11/2402.50645.12.39.50 (sw)2415.12.3 2502.50641.60.73.50896.02.7 21/2652.50641.80.83.50897.03.276.1 2.50642.11.0——31/290x3802.50642.00.99.50 (sw)2417.03.24100x1253.00763.01.413.00 (sw)3306.52.915 F or 14"/350 mm and larger roll grooved systems, Victaulic offers theAdvanced Groove System (AGS). For pricing and availability of cut groove fittings in this size, contact your nearest Victaulic sales representative.No. 50No. 51Fabricated SteelNo. 50Fabricated SteelNo. 51SizeNo. 50 ConcentricReducer No. 51 Eccentric Reducer Nominal Size E to EApprox.Weight Each E to EApprox.Weight Each inchesmminchesmmlbs.kginchesmmlbs.kg11/432+4.62.1——11/2403.00 (sw)762.61.210.00 (sw)2548.13.72503.00762.41.14.001023.31.521/2653.00762.71.24.001023.41.53803.00763.21.44.001023.51.631/2903.00762.91.310.00 (sw)2548.03.65125x25011.00 (sw)2799.04.111.00 (sw)2795.22.421/2654.001024.32.011.00 (sw)27910.84.93804.001025.52.511.00 (sw)27911.15.041003.50894.31.95.0012712.05.46150x1254.001025.02.311.50 (sw)29214.56.611/240+5.52.5++2504.001026.63.011.50 (sw)29214.56.62 1/2654.001026.42.911.50 (sw)29214.26.43804.001026.42.95.5014015.06.841004.001026.52.95.5014017.07.751254.001026.42.95.5014017.07.78200x21/26516.004067.93.612.00 (sw)30526.111.83805.001279.34.212.00 (sw)30522.010.041005.0012710.44.812.00 (sw)30523.010.451255.0012711.65.212.00 (sw)30523.010.461505.0012711.95.46.0015224.010.915 F or 14"/350 mm and larger roll grooved systems, Victaulic offers theAdvanced Groove System (AGS). For pricing and availability of cut groove fittings in this size, contact your nearest Victaulic sales representative.No. 50No. 51Fabricated SteelNo. 50Fabricated SteelNo. 51Size No. 50 ConcentricReducer No. 51 Eccentric ReducerNominal Size E to EApprox.Weight Each E to EApprox.Weight Eachinches mm inchesmmlbs.kginchesmmlbs.kg10250x41006.0015219.78.913.00 (sw)33032.014.55125+33.015.0+34.615.7 61506.0015220.09.113.00 (sw)33036.916.7 82006.0015222.010.07.0017821.69.812300x4100+44.020.014.00 (sw)35648.021.861507.0017824.611.214.00 (sw)35650.022.7 82007.0017852.023.614.00 (sw)35653.524.3 102507.0017839.017.714.00 (sw)35657.025.914350x615013.0033065.029.513.0033060.027.2820013.0033065.029.513.0033060.027.2 1025013.0033066.029.913.0033065.029.5 1230013.0033068.030.813.0033066.029.916400x820014.0035673.033.114.0035573.033.11025014.0035673.033.114.0035573.033.1 1230014.0035673.033.114.0035573.033.1 1435014.0035673.033.114.0035573.033.118450x1025015.0038191.041.315.0038191.041.31230015.0038191.041.315.0038191.041.3 1435015.0038191.041.315.0038191.041.3 1640015.0038191.041.315.0038191.041.315 F or 14"/350 mm and larger roll grooved systems, Victaulic offers theAdvanced Groove System (AGS). For pricing and availability of cut groovefittings in this size, contact your nearest Victaulic sales representative.No. 50No. 51Fabricated SteelNo. 50Fabricated SteelNo. 51Advanced Groove System (AGS). For pricing and availability of cut groove fittings in this size, contact your nearest Victaulic sales representative. General NotesAvailable with male threaded small end No. 52.Cast fitting available for JIS size. Contact Victaulic for details.Steel eccentric reducers available through 30”/750 mm, contact Victaulic for dimensions.Note: All fittings are ductile iron unless otherwise noted with an (sw) or (s). (s) = Carbon Steel Direct Roll Groove (OGS)(sw) = Carbon Steel Segmentally Welded+ Contact Victaulic for details.Small Threaded Reducer No. 52No. 52FNo. 52No 52FSizeNo. 52Small Threader ReducerNo. 52F ConcentricReducer with BSPTFemale Threaded EndNominal Size E to E Approx.WeightEach E to EApprox.WeightEachinches mm inchesmmlbs.kg mm kg11/240x1252.50640.80.4——11/4322.50640.90.4——250x 3/4202.50640.90.4——1252.50640.70.3——1 1/4322.50641.20.5——1 1/2402.50641.00.5——21/265x1252.50641.10.5——11/4322.50 (sw)641.20.5——11/2402.50 (sw)641.30.6——2502.50641.40.6——76.1x48.3640.8640.860——640.9380x 3/420+ (sw)1.50.7——1252.50641.30.6——1 1/4322.50641.50.7——21/2402.50 (sw)641.50.7——2502.50641.50.7——21/2652.50642.41.1——88.9x42.4640.9640.848.3640.9640.960——640.9No. 52No 52FSizeNo. 52Small Threader ReducerNo. 52F ConcentricReducer with BSPTFemale Threaded End Nominal Size E to EApprox.WeightEach E to EApprox.WeightEach inchesmminchesmmlbs.kg mm kg4100x1253.00762.31.0——11/2403.00762.71.2——2503.00762.61.2——2 1/2653.00762.61.2——3803.00762.51.1——108.0x42.476 1.376 1.348.376 1.376 1.460——76 1.4 114.3x42.476 1.376 1.348.376 1.376 1.36076 1.376 1.45125x4100+4.52.0——133.0x60——114 2.2 139.0x60——114 2.36150x1254.001025.52.5——2504.001025.72.6——21/2654.001025.82.6——3804.001025.82.6——4100+ (sw)6.52.9——5125+ (sw)2.00.9——159.0x42.4114 2.2144 2.548.3114 2.2114 2.560——114 2.6NoteThis product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard .equipment without notice and without incurring obligationsInstallationReference should always be made to the Victaulic installation handbook or installation instructions of the product you are installing. Handbooks are included with each shipment of Victaulic products, providing complete installation and assembly data, and are available .in PDF format on our website at Warranty.Refer to the Warranty section of the current Price List or contact Victaulic for details TrademarksVictaulic and all other Victaulic marks are the trademarks or registered trademarks of .Victaulic Company, and/or its affiliated entities, in the U.S. and/or other countriesUser Responsibility for Product Selection and SuitabilityEach user bears final responsibility for making a determination as to the suitability of Victaulic products for a particular end-use application, in accordance with industry standards and project specifications, as well as Victaulic performance, maintenance, safety, and warning instructions. Nothing in this or any other document, nor any verbal recommendation, advice, or opinion from any Victaulic employee, shall be deemed to alter, vary, supersede, or waive any provision of Victaulic Company's standard conditions of sale,.installation guide, or this disclaimerIntellectual Property RightsNo statement contained herein concerning a possible or suggested use of any material, product, service, or design is intended, or should be constructed, to grant any licenseunder any patent or other intellectual property right of Victaulic or any of its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of such material, product, service, or design in the infringement of any patent or other intellectual property right. The terms “Patented” or “Patent Pending” refer to design or utility patents or patent .applications for articles and/or methods of use in the United States and/or other countriesNo. 52No 52FSize No. 52Small Threader ReducerNo. 52F Concentric Reducer with BSPT Female Threaded EndNominal SizeE to E Approx. WeightEach E to E Approx. WeightEach inches mm inches mm lbs. kgmm kg 165.1x 42.4102 2.4102 2.948.3102 2.6102 3.060——102 3.08 200x2 5016.00 406 1.5 0.7——2 1/2 6516.00 4061.7 0.8——General NotesAvailable with British Standard Pipe Threads, specify “BSP” clearly on order.Note: All fittings are ductile iron unless otherwise noted with an (sw) or (s).(s) = Carbon Steel Direct Roll Groove (OGS)(sw) = Carbon Steel Segmentally Welded + Contact Victaulic for details.。
光电耦合器OR-10XX产品规格书说明书
产品规格书Specification Sheet品名(P/N):光电耦合器Photocoupler客户名称(Customer):本厂型号(Mfg P/N):OR-10XX日期(Date):深圳市奥伦德科技股份有限公司(股票代码：832016)Shenzhen Orient Tech Ltd.Co（Ticker Symbol：832016）Web:地址：广东深圳龙岗区黄阁路天安数码城4栋3楼A座518172Add：Block A3rd Floor No.4Building Tian'an Cyber Park Huangge Rd,LongGang Dist,Shenzhen,GD,518172版本版次：A/3●特点(Features)1.电流转换比(CTR:MIN.50%at IF=5mA,VCE=5V,Ta=25℃)2.绝缘电压：(VISO=5,000Vrms)3.高集电极发射极电压(VCEO=70V)4.温度范围：-55℃to110℃5.长爬电距离：>8mm,无铅，符合RoHS标准。
6.CQC approved(No.15801-CQC001041-201800042)7.VDE approved(No.40029733)●说明描述该OR-10XX系列器件包含一个红外发光二极管，光电晶体管探测器。
不含卤素和Sb2O3.它们封装在一个4引脚SOP里面。
●应用范围(Application Range)•可编程控制器•系统设备，测量仪器•电信设备•家用电器，如风扇加热器等。
•不同的电势和阻抗的电路之间的信号传输●最大绝对额定值(常温T=25℃)Max Absolute rated Value(Normal Temperature=25℃)参数Parameter符号Symbol额定值Rated Value单位Unit输入Input 正向电流（Forward Current）I F60mA 结区温度(Junction Temperature)T J125℃逆向电压（Reverse Voltage）V R6V 耗散功率（Consume Power）P100mW输出Output 集极与射极电压(Collector and emitter Voltage)V CEO70V 射极与集极电压(Emitter and collector Voltage)V ECO7集极电流(Collector Current)I C50mA 消耗功率(Consume Power)P C150mW总功率消耗(Total Consume Power)P tot250mW *1绝缘电压(Insulation Voltage)V iso5000Vrms 工作温度(Working Temperature)Topr-55to+110℃存贮温度(Deposit Temperature)T stg-55to+125*2焊锡温度(Soldering Temperature)T sol260*1.交流测试,时间1分钟，湿度.=40~60%AC Test,1minute,humidity=40~60%如下是绝缘测试的方法.Insulation test method as below:(1)将产品的两端短路。
克里克森3TC系列15-35伏特单相小型环境补偿断路器产品介绍说明书
| 3TC SERIES15–35 Amp, Single–Phase, Miniature Ambient CompensatedIntroductionKlixon ® single–phase TC devices are the smallest, lightest, high performance aircraft circuit breakers available today. They represent the state-of-the-art protection of today’s aerospace power systems. Their light weight and small size make them especially well suited for aircraft, avionics and electronic systems.The Klixon ® trademark has set the standard for aerospace circuit breakers. For a small, light weight configuration, the TC series offers the endurance and reliability required by exacting military specifications, and are available in standard current ratings from 15 through 35 amperes.The 3TC is available in 15 to 35 amps.Features• Miniature size • Light weight • Trip–free design• Options include: longer push button, high vibration, randomvibration, metric mounting thread, metric terminal thread, dust boot (part #14500-1 fits 15/32 bushing, part #14500-5 fits 7/16 bushing), terminal hardware • AS58091 qualified• Current rating: 15 to 35 amps • Coordinated ratings• High vibration resistance (option)• High interrupting capacity• Typical use: Where ambient temperature exceeds the 160°F (71°C) maximum of non–ambient compensated thermal circuit breakersPERFORMANCE CHARACTERISTICSMECHANICAL SPECIFICATIONSTRIP CURVEVOLTAGE DROP*Maximum voltage drop at nominal rated current.DIMENSIONS Dimensions in mm [Inch]Page 4CONTACT USAmericas 508-236-2551electrical-protection-sales@Europe, Middle East & Africa +31743578156*********************.com Asia Pacific*************************.com China +86 (21) 2306 1500Japan +81 (45) 277 7117Korea +82 (31) 601 2004India +91 (80) 67920890Rest of Asia +886 (2) 27602006 ext 2808Sensata Technologies, Inc. (“Sensata”) data sheets are solely intended to assist designers (“Buyers”) who are developing systems that incorporate Sensata products (also referred to herein as “components”). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, evaluation and judgment in designing Buyer’s systems and products. Sensata data sheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular data sheet. Sensata may make corrections, enhancements, improvements and other changes to its data sheets or components without notice.Buyers are authorized to use Sensata data sheets with the Sensata component(s) identified in each particular data sheet. HOWEVER, NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATA SHEETS ARE PROVIDED “AS IS”. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATA SHEETS OR USE OF THE DATA SHEETS, EXPRESS, IMPLIED OR STATUTORY, INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD TO SENSATA DATA SHEETS OR USE THEREOF.All products are sold subject to Sensata’s terms and conditions of sale supplied at SENSATA ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS’ PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONS-RELATED INFORMATION Revised 2/7/18ORDERING OPTIONS15 = 15 amp 20 = 20 amp 25 = 25 amp 30 = 30 amp 35 = 35 amp。
迪克森(Dixon)流体传输耦合器(Fluid Transfer Couplings)产品说明说明书
142DPL122877.963.4966 • Engineered Fluid Transfer CouplingsFeatures • P lug is color-coded (5-wire optic) blue or (2-wire optic / thermistor) green • H ighly visible safety orange jacket to meet trip hazard requirements • C ord is bonded mechanically and resistant to abrasion and oil • C ord sets are interchangeable with Scully and Civacon • A ll wiring is compatible with standard Scully color codes and wiring number configurations • T he 9-pin conductor is shielded to be compatible with Scully VIP system • F or mating socket, consult Dixon ®Materials • P lug body: reinforced nylon • B utton contacts: 316 stainless steel • A ll other hardware: stainless steelAPI-Compatible Systems Order Guide Part #Rack Monitor Description FT7000rack monitor, auto switch between 2-wire / 5-wire sensors, ground verification, and trailer identification modules; API RP 1004 / EN13922Safe-T Connect Junction Box Description FT76008-pin, 2J, green API plug, and 30' safety orange coiled cable FT7600-48-pin, 4J, green API plug, and 30' safety orange coiled cable FT7600C10-pin, 4J, green API plug, and 30' safety orange coiled cable FT7600P8-pin, 2J, green API plug, 30' safety orange coiled cable, and Plug-n-Play connector FT7600S8-pin, 2J, green API plug, and 20' safety orange straight cable FT76206-pin, 3J, blue API plug, and 30' blue coiled cable FT7620P6-pin, 3J, blue API plug, 30' blue coiled cable, and Plug-n-Play connector FT7620S6-pin, 3J, blue API plug, and 20' blue straight cable FT763010-pin, 4J, black plug per EN13922, and 30' blue shielded coiled cable FT7630D10-pin, 4J, black plug per EN13922, and 30' blue shielded coiled cable with Dixon Bayco ® break-away Junction Box Description FT7500single cord junction box FT7501dual cord junction box FT7502junction box with Cole Hersee yellow 13-pin break-away FT7503junction box with D-type pigtail break-away Rack Cord Description FT6008-pin, 2J, API thermistor plug, and 30' safety orange coiled cable FT600-48-pin, 4J, API thermistor plug, and 30' safety orange coiled cable FT600C 10-pin, 4J, API thermistor plug, and 30‘ safety orange coiled cable FT600P8-pin, 2J, API thermistor plug, and 30' safety orange coiled cable with 13-pin Plug-n-Play FT600S8-pin, 2J, API thermistor plug, and 20' safety orange straight cable FT6206-pin, 3J, API optic plug, and 30' blue coiled cable FT620P6-pin, 3J, API optic plug, 30' blue coiled cable and Plug-n-Play connector FT620S6-pin, 3J, API optic plug, and 20' blue straight cable FT63010-pin, 4J, black plug per EN13922, and 30' blue shielded coiled cable FT630D 10-pin, 4J, black plug per EN13922, 30' blue shielded coiled cable, andDixon Bayco break-awayFT620Pwith J560 aluminumFT600FT600P with 13-pin plastic FT620FT7500FT7501FT7502。
Tyco 63850-1 FASTON 187 快速断开机械连接器说明书
63850-1FASTON 187, Quick Disconnects, Receptacle, 20 – 16AWG Wire Size, .51 – 1.31mm² Wire Size, Mating Tab Width 4.75 mm [.187 in]08/27/2020 06:43PM | Page 1For support call+1 800 522 6752Terminals & Splices >Quick DisconnectsMating Tab Thickness:.81 mm [ .032 in ]Mating Tab Width: 4.75 mm [ .187 in ]Wire Size:.51 – 1.31 mm²Terminal & Splice Type:ReceptacleFeaturesProduct Type Features Wire Stop NoWire/Cable Type Regular Wire Terminates To Wire & Cable Insertion Force Normal Sealable No InsulatedNoConfiguration Features Connection Capacity SingleBody Features Fully Insulated No Plating Material NickelContact Features Terminal Type Receptacle Terminal & Splice Type Receptacle Terminal OrientationStraight Contact Base MaterialSteel63850-1 ACTIVEFASTON TE Internal #:63850-1FASTON 187, Quick Disconnects, Receptacle, 20 – 16AWG Wire Size, .51 – 1.31mm² Wire Size, Mating Tab Width 4.75 mm [.187 in]View on >FASTON 187|Contact Base Material SteelCrimp Type F-CrimpBarrel Type OpenMechanical AttachmentMating Retention Type DimpleWire Insulation Support WithDimensionsAccepts Wire Insulation Diameter Range 2.29 – 3.3 mm[.09 – .13 in]Overall Length14.99 mm[.59 in]Receptacle Terminal Stock Thickness.3 mm[.012 in]Wire Size.51 – 1.31 mm²Mating Tab Width 4.75 mm[.187 in]Mating Tab Thickness.81 mm[.032 in]Usage ConditionsOperating Temperature Range-40 – 250 °C[-40 – 482 °F]Industry StandardsUL Rating ListedCSA Certified YesPackaging FeaturesPackaging Quantity20000Packaging Method Strip/ReelOtherLine PremierProduct ComplianceFor compliance documentation, visit the product page on >EU RoHS Directive 2011/65/EU CompliantEU ELV Directive 2000/53/EC CompliantChina RoHS 2 Directive MIIT Order No 32, 2016No Restricted Materials Above ThresholdEU REACH Regulation (EC) No. 1907/2006Current ECHA Candidate List: JUN 2020(209)Candidate List Declared Against: JAN 2020(205)Does not contain REACH SVHC08/27/2020 06:43PM | Page 2 For support call+1 800 522 675208/27/2020 06:43PM | Page 3For support call+1 800 522 6752Does not contain REACH SVHCHalogen ContentLow Halogen - Br, Cl, F, I < 900 ppm per homogenous material. Also BFR/CFR/PVC FreeSolder Process CapabilityNot applicable for solder process capabilityProduct Compliance DisclaimerThis information is provided based on reasonable inquiry of our suppliers and represents our current actual knowledge based on the information they provided. This information is subject to change. The part numbers that TE has identified as EU RoHS compliant have a maximum concentration of 0.1% by weight in homogenous materials for lead, hexavalent chromium, mercury, PBB, PBDE, DBP, BBP, DEHP, DIBP, and 0.01% for cadmium, or qualify for an exemption to these limits as defined in the Annexes of Directive 2011/65/EU (RoHS2). Finished electrical and electronic equipment products will be CE marked as required by Directive 2011/65/EU. Components may not be CE marked. Additionally, the part numbers that TE has identified as EU ELV compliant have a maximum concentration of 0.1% by weight in homogenous materials for lead, hexavalent chromium, and mercury, and 0.01% for cadmium, or qualify for an exemption to these limits as defined in the Annexes of Directive 2000/53/EC (ELV). Regarding the REACH Regulation, the information TE provides on SVHC in articles for this part number is based on the latest European Chemicals Agency (ECHA) ‘Guidance on requirements for substances in articles’ posted at this URL: https://echa.europa.eu/guidance-documents/guidance-on-reachTE Model / Part #7-2150007-1OCEAN_2.0_APPLICATOR-E-090F140FTE Model / Part #2-2150007-2OCEAN_2.0_APPLICATOR-E-090F140FATE Model / Part #2-2150007-1OCEAN_2.0_APPLICATOR-E-090F140FTE Model / Part #755336-1DAHT ASSYTE Model / Part #7-2150007-7OCEAN_2.0_SPARE_PART_KIT-090F140FTE Model / Part #2150007-2OCEAN_2.0_APPLICATOR-E-090F140FATE Model / Part #2150007-1OCEAN_2.0_APPLICATOR-E-090F140FCompatible PartsAlso in the Series FASTON 18708/27/2020 06:43PM | Page 4For support call+1 800 522 6752TE Model / Part #E94629-000RT-3-NO.1-0-1.5INTE Model / Part #794727-112P UMNL CAP HSG NATL,BLACKTE Model / Part #60744-1RING CRIMP 18-14 AWG BRTE Model / Part #1969116-1FASTON 187/250 REC HSG 3 CIR NYLON NATTE Model / Part #1738475-1FASTON 250 HSG INFINITE SW NYLON NATTE Model / Part #1738473-1FASTON 250 HSG INFINITE SW NYLON NATTE Model / Part #63959-1FASTON .187 REC 20-16 AWG NPCRSTE Model / Part #521411-1ULTRA-POD 250 ASY REC 22-18 AWG BRTE Model / Part #1-770894-010P SL156 HSG W/THRU BD LATCHTE Model / Part #63696-1FASTON 187 FLAG REC 20-16 AWG NPSTLSplices(1)Quick Disconnects(222)PCB Terminals(46)Joints & Splices(1)Crimp Terminal Housings(38)Customers Also BoughtDocumentsProduct DrawingsProduct DrawingsFASTON 187 RECEPTACLE 20-16 AWG NPCRSTLEnglishCAD Files3D PDF3DCustomer View ModelENG_CVM_CVM_63850-1_G.2d_dxf.zipEnglishCustomer View ModelENG_CVM_CVM_63850-1_G.3d_igs.zipEnglishCustomer View ModelENG_CVM_CVM_63850-1_G.3d_stp.zipEnglishTerms and ConditionsBy downloading the CAD file I accept and agree to the of use.Datasheets & Catalog Pages82004 FASTON Terminals (Insulated and Uninsulated) Catalog - FASTON Receptacles SectionEnglishProduct SpecificationsApplication SpecificationEnglishWire Preparation And Crimp Inspection GuideEnglishProduct Environmental ComplianceTE Material DeclarationEnglishAgency ApprovalsULEnglish08/27/2020 06:43PM | Page 5 For support call+1 800 522 6752。
耦合器加工技术规格说明书
耦合器加工技术规格说明书编制：日期：审核：日期：批准：日期：核技术应用研究所耦合器加工技术规格说明书1、主要部件列表本次耦合器加工采购主要包括耦合器结构和配套的测试部件，部件名称、主2、相关技术要求基本要求：真空连接部分配套垫圈，法兰连接部分配套螺栓和螺母，图纸未尽事宜双方协商确定。
2.1耦合器结构具体尺寸见设计图纸，以下为相关技术要求：1.耦合器结构中主要采用无氧铜和不锈钢材料；2.要求结构内部表面在加工和运输保存过程中，不能出现损伤和氧化的现象，并且指定表面粗糙度达到图纸要求的0.4 um；3.焊接前需进行预装配，按图纸要求将相关部件焊接为一整体。
4.焊接后检测要求水冷通道畅通，水压（或气压）0.3MPa不漏；5.焊接后利用检漏部件对耦合器进行检漏，要求漏率低于1X10-10Pa*m3/s。
2.2耦合器密封和检漏部件具体尺寸见设计图纸，以下为相关技术要求：1.整体采用不锈钢材料，相关部件需焊接为一整体，用于耦合器焊接后检漏以及运输过程中保存；2.按使用要求配套图纸中未画出的卡箍等部件；3.焊接后检漏，要求漏率低于1X10-10Pa*m3/s。
2.3高功率测试部件具体尺寸见设计图纸，以下为相关技术要求。
1.测试腔主要使用铝和不锈钢材料，腔体内部表面要求不能出现损伤，并且指定表面的粗糙度达到图纸要求0.4微米；2.为防止铝表面氧化影响性能，需要在腔体内部表面进行镀银，厚度按图纸要求20微米；3.需要配备有真空泵机组，要求测试腔体真空度可以达到1X10-7Pa。
4.分水器要求在水压（或气压）0.3MPa情况下不漏；5.分水器备有快速接头转换头公头和母头，以及两端带快速接头的水管，水管内径16mm，长度1.5m，可承受水压0.3MPa；6.测试台架采用铝型材组装而成，下方装有万向轮，台面板采用整块铝板1200mm X 600mm X 15mm，要求台架承重大于2倍测试腔重量；3、各部分设计图纸详见采购文件。
耦合器型号与技术参数
耦合器型号与技术参数招商项目：MOLS系列双级起动摩擦偶合器项目类别：机械设备招商区域：全国项目简介：凡需变负荷运转的各种风机，水泵等设备均可采用偶合器实现变速运转，一般可节电1/5到1/3。
本产品广泛应应用在煤炭、矿山、发电、钢铁、冶金、化工、水泥、港口、纺织、石油、食品、陶瓷机械，粮食加工等行业。
我公司是国内首家双级起动摩擦偶合器生产企业，产品市场前景好。
发展空间大。
(1) 靠背轮(2) 机芯(3) 轴承(4) 偶合轮(5) 主动级摩擦块(6) 主动级离心块(7) 反馈级摩擦块(8) 反馈级离心块(9) 输出端轴套本产品采用双级离心摩擦结构，主要由机芯、轴承、偶合轮、主动级摩擦块、主动级离心块、反馈级离心块、反馈级摩擦块、输出端轴套等零部件组成。
偶合器外壳和零部件主体采用铸钢和灰铸铁，耐高温、耐腐蚀，适用于任何工作环境。
摩擦块由多种材料复合而成，具有阻燃、抗静电、耐磨损、临界温度保护等特性，在工作状态下性能稳定，传动效率高。
本产品采用双级离心摩擦结构，主要由机芯、轴承、偶合轮、主动级摩擦块、主动级离心块、反馈级离心块、反馈级摩擦块、输出端轴套等零部件组成。
偶合器外壳和零部件主体采用铸钢和灰铸铁，耐高温、耐腐蚀，适用于任何工作环境。
摩擦块由多种材料复合而成，具有阻燃、抗静电、耐磨损、临界温度保护等特性，在工作状态下性能稳定，传动效率高。
工作原理电动机起动时，偶合器输入端机芯空载起动，随着电机转速的增加，主动级离心块由于离心力的作用被甩出，主动级摩擦块外表面贴向偶合轮内壁，对偶合轮的压力逐渐增大，依靠摩擦力传递转矩，偶合轮开始转动，实现偶合器主动级起动。
当偶合轮转速增至1100 r/min时，反馈级离心块被甩出，反馈级摩擦块外表面贴向机芯内壁，通过摩擦力矩反馈作用于机芯，实现偶合器反馈级起动。
在主动级摩擦块和反馈级摩擦块摩擦力矩的共同作用下，偶合轮转速增至1480 r/min，工作机与电动机同步运转，整个起动过程柔性强，对负载冲击相对较小。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
TKICO 牌去耦合器 技术规格书
QQ:120835909corrtech@
去耦合器是一种集固态SSD排流与浪涌保护于一体的交流等杂散干扰的防护产品，具有较高的AC故障电流通流能力和极低的阈值电压水平。
安装在管道附近的高压输电线路铁塔/通讯铁塔以及它们的接地系统附近、高压输电线路与管道并行段的公共走廊内、管道与输电线路交叉位置处、与电气化铁路并行的管段等地方。
用来降低管道上感应的交流等杂散电流或雷电流对埋地管道的不良影响。
1、符合的规范和标准
—— NFPA70 250-6（e）国家电气规程；
—— IEC61643.1-2005 连接低压配电系统的电涌保护器 第1部分：性能要求和试验方法 ；
—— NACE RP0177 减轻交流电和雷电对金属构筑物和腐蚀控制系统影响的措施；
—— GB/T 2423 电工电子产品环境试验；
—— GB11032 交流无间隙金属氧化物避雷器；
—— GB4208 外壳防护等级（IP代码）；
——SY/T0032—2000 埋地钢制管道交流排流保护技术标准；
2、环境适应性
TKICO牌去耦合器应能适应温度为-40℃至+60℃，相对湿度为20%至90%的长期工作环境。
去耦合器可防潮、防盐雾、防细菌。
3、主要性能参数要求
表1 性能参数
4、TKICO牌去耦合器的外部保护箱
去耦合器的外壳护箱为金属机壳，厚度1.5mm冷轧钢板，保护具有良好的防雨水、防尘的能力，保护等级为IP68。
图2. 去耦器内部接线图。