UTR9000-联泰SLA树脂资料(汇编)

合集下载

UPR(树脂)-MSDS.doc

UPR MSDSMATERIAL SAFETY DATA SHEETUnsaturated Polyester ResinSECTION 1: PRODUCT AND COMPANY IDENTIFICATIONProduct Name: Unsaturated Polyester ResinManufacturer: King Way CorporationAddress: No. 40 Guizhou Road, QingdaoPostcode: 266001E-mail: resinschina@Fax: 0+86-532-8267-1533National emergency telephone:0+86-532-8388-9090；0+86-532-8388-9191SECTION 2: COMPOSITION AND INFORMATION ON INGREDIENTS Monomer □Mixture■（不饱和聚酯/苯乙烯）Product Name: Unsaturated Polyester ResinHarmful substance Content CAS NO.Styrene 35-55％ 100-42-5SECTION 3: HAZARDS IDENTIFICATIONRisky category: 3.3rd kind, high flash point flammable liquid.Routes of Entry: Inhalation, Swallowing, Skin ContactHealth effects: The risk mainly is decided by the styrene which is additive, the styrene has the fetid odor which makes one laughs, may stimulate skin and the respiratory tract. Eating at nonventilated room may stimulate the mucosa.Environment effects: This matter has harm to environment, Pay attention specially to water body pollution.Explosion hazard: Flammable, its steam and air may form explosive gas. In presence of open flames or high heat, it has a danger of burning or explodes.SECTION 4: FIRST AID MEASURESSkin Contact: remove contaminated clothing and shoes. Flush skin with soap and water.Eye Contact: Check for and remove any contact lenses. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention immediately.Inhalation: If inhaled, remove to fresh air. If not breathing, give artificial respiration and heart massage technique immediately. Get medical attention immediately, to avoid epinephrine. Ingestion: Drink enough hot water, force to vomit, Get medical attention immediately.SECTION 5: FIRE FIGHTING PROCEDURESFlammability of Product: Flammable in presence of open flames, heat and oxidant. Risks of making container blasted in presence of polymerizing.Harmful burning gas: COFire Fighting Media and Instructions: Use dry chemical, carbon dioxide, appropriate foam, or sand .The water is prohibited use.SECTION 6: ACCIDENTAL RELEASE MEASURESEmergency measures: Keep away from sources of ignition. Rapid evacuation personnel which divulged in the pollution area to the safety zone, and carries on the isolation, strictly limits thein/out. Advised the personnel who emergency processing should be wear self-sufficient respirator, put on anti-poison clothing, shuts off as far as possible the divulged source.Large Spill and Leak: Dike if needed. Use water spray curtain to divert vapor drift. Use water spray to reduce vapors. Protection filed personnel .With explosion-proof Pumps shift to the tank car or the special-purpose collector, then recycling or transports to waste scene processing.SECTION 7 : HANDLING AND STORAGEHandling: The operator must pass through the specialized training, strictly observes the working instruction. Suggestion operator wears mouthpiece or self-absorption filter gas mask, wear chemistry security safekeeping eyeglasses, put on anti-poison seepage work clothes, wear rubber resistant oil glove. Keep away from heat, sparks and flame, prohibiting smoking in the work area. Use defending explosion-proof ventilation system and equipment. Prevent the steam divulges to the operational site air. Avoid contact with the oxidant. Should pay attention to the speed of flow (not to surpass 5m/s) when canned, and have grounding equipment, prevent the static electricity accumulation. When transporting must lightly unload and light packs, prevents package or vessel damage, and provides the variety corresponding fire-fighting equipment and handling emergency divulged. The vessel Dumped possibly remains harmfully.Storage: Keep container in a cool, well ventilated area. Keep away from heat, sparks and flame. The warehouse temperature do not surpass 30℃, keep the vessel seal. Should separate with the oxidant, food chemical, prohibit stores together. The illumination and ventilates equipment should be explosion-proof. Prohibited using easily produces the spark mechanical device and the tool. The store area should to have divulges emergency and appropriate accepts the material.SECTION 8: EXPOSURE CONTROLS PERSONAL PROTECTIONHigh the admissable concentration: 40mg/m3 (in air)Moniting method: GCEngineering Controls: Provide exhaust ventilation or other engineering controls to keep the airborne concentrations of vapors below their respective occupational exposure limits.Personal Protection:Eyes: Safety glasses and gloves.Body: Full suit.Hands: Rubber and oil-resistant gloves.Other protection: prohibiting smoking, eating and drinking in the work area. Before the work avoids with alcohol drink, after the work, please bath and changes clothes, carries on physical examination before the employment and the regular.SECTION 9: PHYSICAL AND CHEMICAL PROPERTIESPhysical State and Appearance: viscous fluid with various colors.Melting point（℃）：-30.63Specific Gravity (Water=1):1:120.02Boiling Point（℃）：145.2Auto-temperature（℃）：490Saturated Vapor Pressure（KPa）：1.33/30.8℃※Combustion Heat（kj/mol）：4242.78Critical Temperature（℃）369.0※Critical pressure （mpa）：3.81※Flash points （℃）：23-61upper Explosion limits ％（v/v）：7：1lower Explosion limits ％（v/v）：6.5Solubility: Insoluble in water, soluble in acetone and acther.Main use: used extensively in thermoset composite material and reinforcing material. Note: refer to physical and chemical properties of styrene.SECTION 10: STABILITY AND REACTIVITYStability: unstable and may polymerice uponexposure to sunlight, heat or peroxide.Incompatibility with Various Substances: Reactive with oxidant.Conditions to avoid: naked flames, high temperature and heating.Hazardous Polymerization: Release large heat when polymerization.Decomposition Products: CO, CO2SECTION 11: TOXICOLOGICAL INFORMATION(On account of unsaturated polyester resin’s molecular weight of number average is over 1,500 and it has lower solubility. It can’t be absorbed through skin absorption and permeate organism cell. So it cann’t display toxicity. Because of unsaturated polyester resin’s low fluidity, it has litter damage to the environment. According to American FDA and EPA research, Australian EPA think non-ionic polymer which average molecular weight is over 1,000 concerns degree should be lower. But unsaturated polyer resin’s diluent is styrene, its toxictity and Ec ological information is relevant to styrene.)Acute toxicity: Acute oral toxicity (LD50) 265mg/kg [Mouse]Acute toxicity of the vapor (LC50) 12mg/m3/4h [Mouse]Acute Poisoning: In case of high concentration contact, may lead to eye and upper respiratory tract irritant. May cause ophthalmalgia, lacrimation, rhinorrhea, sneezing, pharyngodynia and cough. Continues the headache, dizziness,nausea, vomits, the whole body feels weak and so on; Serious may have the dizziness, staggering gait. When the eye is polluted by styrene, it may send burns.Chronic Poisoning: At times the symptoms of tiredness,response slowing and memory decreasing emerged in long-term exposure in the surrounding of 100ppm.Red and white blood cell population varied,as well as peripheral nerve and sense organ.Other changes of liver was caused by nutritional marasmus and the marasmus induced by total metabolism changing,other biocatalysts also varied.Irritancy: Draize test (rabbit) 100mg/24h moderateOpen draize test (rabbit) 500mg open slightMutagenicity Effects: DNA suppresses Gymphocyte cell 100umol/L.The sister chromosomes exchange Gymphocyte cell 100umol/L.Carcinogenicity: The research indicated,to the long-term contact crowd the mortality rate has not increased, cancer mortality rate has not increased, cancer formation rate has not increased. SECTION 12: ECOLOGICAL INFORMATIONEcology toxicology toxicity : 56.7mg/L 124-hr（de-ionized water），Pimophales Pronolas TL m53.6kg/L 148hr（de-ionized water），Pimophalespronolas TL m25.1kg/L 196hr （20mg/Lca CO3），Pimophalws pronolas LC20 9.1mg/L 196hr Cyprinido varieyatus LC50 26mg/L 124hr Cyprinido varieyatusBiodegradation: It has 2.3 –4.3% to degeneration in the earth’s surface of each week, and has2.8-12.0% to degeneration in the soil, Styrene has a 93% to be possible to degrade in 16 weeks and degradation product is carbon dioxide and waterNon- biodegradation: Styrene can very quickly react with the OH free radical and O3 in the air, the reaction half-life is 5h, the soil migration ratio is slightly, KOC is 270-550.The biology concentrates the nature: BCF, 13.5 goldfishes, because of relative highwater-solubility, it can not accumulate in the biological tissue.SECTION 13: DISPOSAL CONSIDERATIONSWaste material group: Dangerous waste.Waste disposal method: Incinerate in a furnace where permitted under nation and local regulations.SECTION 14: TRANSPORT INFORMATIONDangerous goods number: 33645UN Number: UN1866Packaging labeling: Flammable liquid.Packaging Group: ШPackaging method: Pails or drums.Notes: Store in cool and well ventilated warehouse. Far away from kindling material, heat source and direct sunlight. The illumination and ventilates equipment in the warehouse must be explosion-proof. The switch is located in the outside the warehouse. According to standard request dispose corresponding fire-fighting equipment. Prohibited using easily produces the spark mechanical device and the tool. When transporting should lightly put and unloads and away from direct sunlight, when transporting please abide by routing run.SECTION 15: REGULATORY INFORMATIONChemistry dangerous goods safety control rule(On January 9, 2002 the State Council issued), In view of chemistry dangerous material safety in production, use, storage, transportation, loading and unloading has made the corresponding stipulation.《General Dangerous Chemical Classification And Symbol》(GB 13690-1992), divide it into the 3.3rd kind of high flash point flammable liquid.SECTION 16: OTHER INFORMATIONReferences1、Heitmuller,R I,et al Bull.environ.Contam.Toxicol.1981，27，596-604。

UTR9000 联泰SLA树脂资料

UTR9000 TECHNICAL DATA SHEET PRODUCT DESCRIPTION 产品介绍C-UV 9400 is an ABS like SL resin which has accurate and durable features. It is designed for solid state SLA platforms. C-UV 9400 can be applied in master patterns, concept models, general parts and functional prototypes in the field of automotive, medical and consumer electronics industries.The parts duability building with UTR9000is over 6.5months.UTR9000 是一种具备精确和耐久特性的类ABS的立体光造型树脂。

它被用于固态激光的光固化成型法。

UTR9000可应用于于汽车，医疗，消费电子等工业领域的母模，概念模型，一般部件，功能性部件的制作。

用UTR9000树脂制造的部件的耐久性长达6.5个月以上。

TYPICAL FEATURES典型特点-Liquid resin`s medium viscosity, so easy recoating, easy clean parts and machines 中等粘度的液态树脂，确保其更容易涂层以及清洗部件和机器-Improved strength retained, improved dimensions retention of parts in humid condition 在潮湿环境中具有更好的强度及尺寸保持特性-need minimal part finishing只需要极小的部件修饰-Long shelf life in machine更长的实际使用期限TYPICAL BENEFITS典型优点-Need less part finishing time,easier post-curing 更少的部件完成时间-Buliding accurate and high tough parts with an improved dimensional stability 能够建造精确和高韧性的部件并提高了部件的尺寸稳定性-High quality controls for vacuum casting parts 对于真空铸造部件的高质量控制-Low shrink and good resistance to yellowing 低收缩和优异的耐黄变性-Magnificent white color 华丽的白色外观-Outstanding machinable SLA material 卓越的可加工性Physical Properties – Liquid Material 液态材料的物理性能Appearance外观White白色Density 密度 1.13g/cm3 @ 25 ℃Viscosity 粘度355 cps @ 28 ℃Dp 固化深度0.145 mmEc 临界曝光量9.3 mJ/cm2Building layer thickness0.1mm建造层厚Mechanical Properties of Post-Cured Material 固化后材料的机械性能MEASUREMENT测试项目TEST METHOD 测试方法V ALUE 数值90-minute UV post-cure 90分钟紫外固化Hardness 硬度, Shore D ASTM D 2240 83Flexural modulus 弯曲模量, Mpa ASTM D 790 2,692-2,775Flexural strength 弯曲强度, Mpa ASTM D 790 69- 74Tensile modulus 拉伸模量, MPa ASTM D 638 2,189-2,395Tensile strength 拉伸强度, MPa ASTM D 638 27-31Elongation at break 断裂延长率ASTM D 638 12 -20%ASTM D 256 58 - 70Impact strength,notched lzod, J/m缺口冲击强度ASTM D 648 @66PSI 52Heat deflection temperature, ℃热变形温度Glass transition,Tg玻璃化转变温度，℃DMA，E”peak 62Coefficient of thermal expension,热膨胀系数, /℃TMA(T<Tg) 97*E-6Density 密度, g/cm3 1.16注：使用温度和保存温度不宜过高，请在25摄氏度以下使用；推荐使用和保存温度为18-25摄氏度。

Axalta 392-9008-00 RTU 填充材料说明书

The data on this sheet represent typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Axalta assumes no obligation or liability for use of this information. UNLESS AXALTA AGREES OTHERWISE IN WRITING, AXALTA MAKES NO WARRANTIES, EXPRESS ORIMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. AXALTA WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in thisproduct is the replacement of the defective product, or a refund of its purchase price, at our option. The information in this sheet, as well as the products referenced herein, shall beGENERAL INFORMATIONAxalta ’s RTU Filler is a high quality, non-greasy pre-fill designed to assist in filling and leveling of open pore substrates. It isdesigned for use direct-to-wood to help fill the pores on open grain substrates including oak, mahogany, elm, ash or hickory and may be applied by brush, rag, squeegee or spray if reduced.1. PRODUCTS• 392-9008-002. MIXING RATIO• All products should be stirred well before use and, for bestresults, continuously agitated while in use.3. SHELF LIFE @ 77°F (25°C)• 18 months from manufacturing date4. CLEAN UP• Dispose of dirty solvent and cleaning rags in a safe andcompliant manner. Solvent or lacquer soaked rags should be stored in water-filled, closed containers prior to disposal.5. ADDITIVES• N/A6. SURFACE PREPARATION• Surface must be clean and dust free with a moisturecontent of 6-8% prior to finishing. Remove all dust, dirt, wax and wood marks. Proper sanding and preparation of the wood is critical to achieving consistent results.• On new wood, finish sand surface with 150-180 grit sandpaper• On previously finished wood, remove all old paint or varnish and follow new wood procedure.7. COMPANION PRODUCTS• GRAINTONE PLUS™ Colour Systems8. TECH NOTES• No thinning is recommended.9. SUBSTRATES• Commonly used furniture and cabinetry woods • MDF/HDFNOTE: Not to be used on exterior applications10. APPLICATION• See Application Notes for additional details.11. FLASH / DRY TIMESAIR DRY @ 77°F (25°C)AIR PRESSURES14.PHYSICAL DATAThe data on this sheet represent typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Axaltaassumes no obligation or liability for use of this information. UNLESS AXALTA AGREES OTHERWISE IN WRITING, AXALTA MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. AXALTA WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in thisproduct is the replacement of the defective product, or a refund of its purchase price, at our option. The information in this sheet, as well as the products referenced herein, shall be。

TL9000标准教材

Measurements) --硬件测量 (Hardware Measurements) --软件测量 (Software Measurements) --服务测量 (Service Measurements)
TL9000标准教材
TL9000模式
• QeEST Forum聚焦的地方
要求手册
ISO9001国际标准
ISO 9001：2000 要求
新增要求（81项）
c 39 项硬件、软件和服务共
c 用的要求
c 15 项软件专用要求
c 12 项硬件专用要求
c c c
5 项服务专用要求 6 项硬件和软件专用要求 4 项硬件和服务专用要求
c
c
c
TL9000标准教材
TL9000标准教材
条款的适用范围的表示
• C——公共要求； • H——硬件要求； • S——软件要求； • V——服务要求 • HS——硬件和软件要求； • HV——硬件和服务要求； • VS——服务和软件要求。
TL9000标准教材
TL9000和ISO9000之间的主要区别
产品寿命周期模式衡量—从客户角度提出——用以衡量组织的品质表现
❖ 定义 ❖ 追踪 ❖ 报告强调用数据事实为依据决定所采取的行动 ❖ 问题的识别 ❖ 缺陷分析 ❖ 改善行动
TL9000标准教材
TL9000和ISO9000之间的区别
TL 9000简介
TL 9000：是由包含 Bell、AT&T、Motorola -- 等世界卓越之通信服务提供者 (Telecommunications Service Providers ；TSP)以及他们的供货商组成「通信业领袖卓越品质论坛」(QuEST Forum ： Quality Excellence for Suppliers of Telecommunications Leadership Forum)，基于要明订通信电子业包含硬件、软件、服务各部门从设计→开发→制造→配送→ 安装→维护的品质系统要求，以 ISO 9000 为基础，共同努力发展的一项以通信电子业产品为主的品质管理标准。

2016年进口杜笙Tulsion树脂使用指南

: ulsionT ® 600-ADS
: ulsionT ® 750-ADS
:
ulsionT ® EP 800-ADS 最常选用的型号是 - :
ulsionT ® 107-A - 最常选用的型号是 :
Tulsion® T-ISR - 最常选用的型号是 :
Tulsion® ARR-1
最常选用的型号是 - : MP 42-T ®ulsionT
• (Br)除溴化物
-最常选用的型号是
: 33-A 5ppb ＜去除至
• 重金属选择性去除，脱碱软化
- 最常选用的型号是 :
• 镍的去除回收
:大孔螯合树脂
12MP-CXO
- 最常选用的型号是 :
• 铂金钯金的去除回收的去除回收Fe3+ 价铁 3 •
:螯合树脂
90-CH
- 最常选用的型号是 :
:螯合树脂
最常选用的型号是可以根据需要定制
ulsionT 与 ® R-MP 2X-A :
ulsionT ® 100/200 CMB
最常选用的型号是 : 最常选用的型号是 : 最常选用的型号是 : 最常选用的型号是 :
®ulsionT 335 343 , 339 , ®ulsionT 344 ®ulsionT 412 ®ulsionT 345
吸附碘专用离子交换树脂乙二醇中去除醛类用离子交换树脂
明胶、果冻等脱灰清灰除杂等 • 树脂 merrifeid 固相肽合成用 •
Industries) (Pharmacy 制药业等级 • 去苦味剂药效缓释剂降胆固醇药剂含量剂,K,降低血中钾
纯化己内酰胺用离子交换树脂
最常选用的型号是最常选用的型号是最常选用的型号是 -

(在23℃水中沉浸24个小时)(平衡50%RH)

拉伸强度
拉伸强度延伸率
Թ౓ (ˆ)
图 1.1-3 拉伸强度对温度的依存性温度
温度
拉伸速度 (mm/min)
图 1.1-4 拉伸强度的速度依存性
1.2 抗弯强度
Iupital 以变形速度 10mm/min 弯曲时的应力应变曲线、弹性模量应变曲线如图 1.2-1、1.2-2 所示，
温度依存性如图 1.2-3 所示。
众所周知，塑料通常会出现应力开裂或者溶剂腐蚀的现象。尽管 Iupital 是一种不易发生应力开
裂的材料，但是在应力集中部分、焊缝等处仍有可能出现开裂。对 Iupital 的应力比较敏感的药品
有盐酸等。
表 3.2 Iupital 的耐化学药物、耐油性能
沉浸条件
变动率 (%)
类别
药品名称
浓度 n(%) 温度(℃) 拉伸强度尺寸重量
Iupital 的抗剪强度如下所示
抗剪强度
560kg/cm2
剪应变
试验片厚度 (A) 1mm(B) 2mm
应变速率
1mm/min
温度 23ˆ
Байду номын сангаас
剪应变 (mm) 图 1.4-1 剪应力与剪应变的关系
1.5 冲击强度
在各种不同边角形状时的冲击强度和冲击疲劳性能如图 1.5-1、1.5-2 所示。
Iupital 的冲击强度如以下所示。
1.3 抗压强度
受压应力应变曲线如图 1.3-1 所示
Iupital 的抗压强度如下所示 (ASTM D-695)
抗压强度
1% 变形 310kg/cm2
10% 变形
1050kg/cm2
压缩应力
高压应变 (%) 图 1.3-1 受压应力应变曲线

施工缩写中文名称英文名称(修正)

缩写中文名称英文名称P管子 Pipe EL 弯头 ElbowELL 长半径弯头 Long radius elbow ELS 短半径弯头 Short radius elbowMEL 斜接弯头（虾米腰弯头） Mitre elbow REL 异径弯头 Reducing elbowPE 管口是平端即无坡口 Ej=0.85焊缝系数=0.85T 三通 TeeLT 斜三通 Lateral teeRT 异径三通 Reducing teeR 异径管接头（大小头） ReducerCR 同心异径管接头（同心大小头） Concentric reducerER 偏心异径管接头（偏心大小头） Eccentric reducerCPL 管箍 CouplingFCPL 双头管箍 Full couplingHCPL 单头管箍 Half coupling RCPL 异径管箍 Reducing couplingBU 内外螺纹接头 Bushing UN 活接头 UnionHC 软管接头 Hose coupler SE 翻边短节 Stub endNIP 短节 Pipe nipple or straight nipple SNIP 异径短节 Swaged nippleCP 管帽（封头） Cap PL 管堵（丝堵） PlugBLK 盲板 Blank SB 8字盲板 Spectacle blind （blank）RP 补强板 Reinforcing pad法兰缩写中文名称英文名称PLG 法兰 Flange WNF 对焊法兰 Welding neck flange SOF 平焊法兰 Slip-on flange SWF 承插焊法兰 Socket-welding flange T 螺纹法兰 Threaded flange LJ 松套法兰 Lapped joint flange REDF 异径法兰 Reducing flange BF 法兰盖（日法兰） Blind flangeFSF 法兰密封面 Flange scaling face FF 全平面 Flat faceRF 凸台面 Raised face MFF 凹凸面 Male ａnd female faceLF 凹面 Female face LM 凸面 Male faceRJ 环连接面 Ring joint face TG 榫槽面 Tongue ａnd groove face TF 榫面 Tongue face GF 槽面 Groove face垫片缩写中文名称英文名称G 垫片 GasketNMG 非金属垫片 Non-metallic gasketAG 石棉垫片 Asbestos gasketRG 橡胶垫片 Rubber gasketTEG 聚四氟乙烯包复垫片 PTFE envelope gasketSMG 半金属垫片 Semimetallic gasketMJG 金属包垫片 Meta-jacket gasketSWG 缠绕式垫片 Spiral wound gasketMG 金属垫片 Metallic gasketFMG 金属平垫片 Flat metallic gasketSMSG 齿形金属垫片 Solid metal serrated gasketLER 透镜式金属环垫 Lens ring gasketOCR 八角形金属环垫 Octagonal ring gasketOVR 椭圆形金属环垫 Oval ring gaksetIR/OR 内外定位环 Inner ring ａnd outer ringIR 内定位环 Inner ringOR 外定位环 Outer ring坚固件缩写中文名称英文名称B 螺栓 Bolt SB 螺柱 Stud boltNU 螺母 Nut TB 花蓝螺母 TurnbuckleWSR 垫圈 WasherSWSR 弹簧垫圈 Spring washer阀门缩写中文名称英文名称GV 闸阀 Gate valve GLV 截止阀 Globe valveCHV 止回阀 Check valveBUV 蝶阀 Butterfly valveBAV 球阀 Ball valve PV 旋塞阀 Plug valve （cock）CV 调节阀 Control valveSV 安全阀 Safety valveRV 减压阀 Pressure reducing valveST 蒸汽疏水阀 Steam trapPRV 泄压阀 Pressur relief valveBV 呼吸阀 Breather valveNV 针形阀 Needle valveAV 角阀DV 隔膜阀TWV 三通阀SGV 插板阀管道上用的小型设备缩写中文名称英文名称SPR 气液分离器 Separator FA 阻火器 Flame arresterSR 过滤器 StrainerSRY Y型过滤器 Y-type strainerSRT T型过滤器 T-type strainerSRB 桶式过滤器 Bucket type strainerTSR 临时过滤器 Temporary strainerSIL 消声器 SilencerSG 视镜 Slight glassSC 取样冷却器 Sample coolerDF 排液漏斗 Drain funnelLM 管道混合器 Line mixerRO 限流孔板 Restriction orificeMO 混合孔板 Mixing orificeRD 爆破片（爆破膜） Rupture diskEJ 补偿器 Expansion joint隔热、伴热中文名称英文名称INS 隔热 Thermal insulationH 保温 Hot insulationC 保冷 Cold insulationP 防烫伤隔热 Personnel protection insulationT&I 伴热 Tracing ａnd insulation管道伴热（冷） TracingEST 蒸汽外伴热 External steam tracingIST 蒸汽内伴热 Internal steam tracingSJT 蒸汽夹套伴热 Steam-jacket tracingET 电伴热 Electric tracing配管材料和等级缩写中文名称英文名称M 金属材料 Metallic materialCS 碳钢 Carbon steelCAS 铸钢 Cast steel FS 锻钢 Forged steelAS 合金钢 Alloy steel SS 不锈钢 Stainless steel-AUST-SS 奥氏体不锈钢 Austenitic stainless-steelCI 铸铁 Cast ironMI 可锻铸铁 Malleable ironDI 球墨铸铁 Ductile iron AL 铝 AluminumBRS 黄铜 Brass BRZ 青铜 BronzeCU 紫铜 CopperLAS 低合金钢 Low alloy steelFLAS 低合金锻钢 Forged low alloy steel CLAS 低合金铸钢 Cast low alloy steelTHK 壁厚 ThicknessSCH 表号 Schedule number（美标壁厚）STD 标准 Standard XS 加强 Extra strongXXS 特强 Double extra strong装置布置缩写中文名称英文名称CN 建北 Construction northE 东 EastW 西 WestS 南 SouthN 北 NorthH 水平 HorizontalV 竖直、铅直、直立 VerticalGRD 地坪 GroundUG 地下 UndergroundBL 装置边界线 Battery limit lineESEW 事故沐浴洗眼器 Emergency shower ａnd eye washerHS 软管站 Hose stationML 接续分界线 Match linePS 管道支架（管架） Piping supportPR 管桥 Pipe rackSTRU 构架（构筑物） StructureBLDG 建筑物 BuildingPD 清扫设施 Purge devicePT池PitSHLT 棚 ShelterCOFF 围堰 CofferdamFL 楼板 FloorPF 平台 Plateform尺寸标注缩写中文名称英文名称EL 标高 ElevationBOP 管底 Bottom of pipeCOP 管中心 Center of pipeTOP 管顶 Top of pipe FOB 底平 Flat on bottomFOT 顶平 Flat on topCL（屯）中心线 Center lineTL 切线 Tangent lineSYM 对称的 SymmetricalBOS 支架底 Bottom of supportTOS 支架顶 Top of supportCL 净距（净空） ClearanceCTC 中心至中心 Center to centerCTF 中心至面 Center to faceCTE 中心至端部 Center to endETE 端到端 End to endFEF 法兰端面 Flange ａnd faceFTF 面到面 Face to faceD 直径 DiameterDN 公称直径 Nominal diameterID 内径 Inside diameterOD 外径 Outside diameterDIM 尺寸 DimensionMAX 最大 MaximumMIN 最小 Minimum AVG 平均 AverageAPP 约、近似 ApproximatePT.EL 点标高 Point elevation图表缩写中文名称英文名称PFD 工艺流程图 Process flow diagramPID 管道和仪表流程图 Piping & instrument diagram COD 接续图 Continued on drawing DTL 详图 DatailSPDWG（ISODWG）管段图 Spool drawing （each line isometric drawing）DWGNO 图号 Drawing numberDWGI 所在图号 Drawing identificationLOW 材料表 List of materialMTO 汇料 Material take-offAPPX 附录 AppendixJOB. No. 工号 Job NumberBEDD 基础工程设计数据 Basic engineering design dataDEDD 详细工程设计数据 Detail engineering design dataREV. No. 修改号 Recision numberREFDWG 参考图 Reference drawingSC 采样接口 Sample connection操作方式及工作参数缩写中文名称英文名称AUT 自动 AutomaticML 手动 Manual controlCHOP 链条操作 Chain operatedCSC 铅封关 Car seal closeCSO 铅封开 Car seal openLC 锁闭 Lock closedLO 锁开 Lock openNC 正常关 Normally closeNO 正常开 Normally openATM 大气压 AtmospherePN 公称压力 Nominal pressureA 绝压G 表压（T）温度 Temperature（P）压力 Pressure施工缩写中文名称英文名称W 焊接 WeldingAW 电弧焊 Arc weldingGSAW 气体保护电弧焊 Gas shielded-acr weldingEFW 电熔焊 Elecric fusion weldingERW 电阻焊 Electric Resistance weldingGW 气焊 Gas weldingLW 搭接焊 Lap weldingBW 对焊 Butt weldingTW 定位焊 Tack weldingSW 承插焊 Socket weldingCW 连续焊 Continuous weldingSEW 密封焊 Seal weldingSFG 堆焊 SurfacingFW 现场焊接 Field weldingHT 热处理 Heat treatmentPH 预热 Preheating埋弧焊（SAW）熔化气体保护焊（GMAW）-SR 应力消除 Stress relief-PWHT 焊后热处理 Post weld heat treatmentEIT 检查、探伤和实验 Examination, inspection & testingVE 外观检查 Visual examinationUI （UT）超声探伤 Ultrasonic inspection （test）RI （RT）射线探伤 Radiographic inspection （test）MPI（MT）磁粉探伤 Magnetic particle inspection（test）LPI（PT）液体渗透检验 Liquid penterant inspection（test）HADT 硬度实验 Hardness testingHYDT 水压实验 Hydraulic testingPNET 气压实验 Pneumatic testing焊条 Covered electrodeWW 焊丝 Welding wireASSY 装配、组合 AssemblyF 现场 FieldF/F 现场制造 Field faricatedSF 现场决定 Suit in field CSP 冷紧 Cold springBCT 螺栓冷紧 Bolt cold tighteningBHY 螺栓热紧 Bolt hot tightening CO 清洗口 Clean out ANNY 退火 AnnealedPE 平端面 Plain endBE 坡口端 Belelled endTHR 螺纹 ThreadHB 布氏硬度 Brinnel hardnessRC 洛氏硬度其他缩写中文名称英文名称FDN 基础 FoundationINF 信息（资料） InformationREF 参考 ReferenceREV 修改 RevisionSEQ 序号（顺序） SequenceW/E 设备带来 With equipmentW/I 仪表带来 With instrumentCM 色标 Colour markCA 腐蚀裕度 Corrosion allowanceUTL 公用系统 UtilityUC 公用工程接头 Utility connectionQTY 数量 QuantityWT 重量 WeightMHR 工时 Man hourBC 螺栓分布圆 Bolt circleHP 高点 High pointLP 低点 Low pointSUC 吸入（口） SuctionDIS 排出（口） DischargeSO 蒸气吹扫（口） Steam outNPT 美国标准锥管螺纹 National standard taper pipe threadNPS 美国标准直管螺纹 National standard straight pipe threadDR 排液 DrainVT 放气 VentRTG （压力）等级 RatingCL 等级 ClassSMLS 无缝 Seamlesswelded 焊接管件管件端部连接件中英文对照表法兰端 flanged end坡口端 beveled end (BE)对焊端 butt welded end平端 plain end (PE)承插焊端 socket welding end螺纹端 threaded end (TE)承口 bell end焊接端 welding end法兰连接（接头） flanged joint对焊连接（接头） butt welded joint螺纹连接，管螺纹连接 threaded joint, pipe threaded joint 锥管螺纹密封焊连接 seal-welded taper pipe threaded joint 承插焊连接（接头） socket welded joint承插连接（接头） bell and spigot joint环垫接头 ring joint (RJ)万向接头 universal joint软钎焊连接（接头） soldered joint搭接接头，松套连接 lapped joint外侧厚度切斜角 bevel for outside thickncss内侧厚度切斜角 bevel for inside thickness内外侧厚度切斜角 bevel for combined thickness法兰式的 flanged (FLGD)对焊的 butt welded (BW)螺纹的 threaded (THD)承插焊的 socket welded (SW)小端为平的 small end plain (SEP)大端为平的 large end plain (LEP)两端平 both ends plain (BEP)小端带螺纹 small end thread (SET)大端带螺纹 large end thread (LET)两端带螺纹 both end thread (BET)一端带螺纹 one end thread (OET)支管连接 branch connection焊接支管 branch pipe welded directly to the run pipe。

TL9000操作手册

电话：010-62316613 62316614 62318085 62318086 传真：010-62323505 网址： E-mail：cds@
2 北京泰立化电子技术有限公司
TELEH ELECTRONICS CO., LTD
TL9000 系列色谱数据工作站
功耗
： ≤10W(注 2)
注1：此量程为各A/D转换器的基本量程范围，不同型号的A/D转换器的量程会有不同。
注2：此功耗为调理单元的最大功耗，不同型号的调理单元功耗不同。
峰处理：
积分灵敏度处理峰宽保留时间分辨率最大保留时间处理峰个数
计算机要求
： 0.1 微伏.秒： 0.5 秒～500 秒： 0.05 秒： ≥600 分：标准配置为每个通道大于 5000 个峰
将数据线插在色谱信号 A/D 转换器的 RS-232 的接口上，另一端的插在电脑的通讯 COM 上(此时电脑主机应处于关闭状态)；（对于网络版用户，此时把网线接头插在 RJ45 接头内，网线的另一端通过交换或集线器与电脑网卡间通讯）
接通电源，按压电源开关，接通色谱信号 A/D 转换器的电源，此时电源指示灯亮；
重复性
： ≤±0.005％最大 [清零偏置]
通讯规范
：符合 RS--232 或 422 标准
通讯距离
：一般 15 米，加驱动器可达 12 公里
[工作站与信号调理单元之间的最长连接距离]
远程启动方式
：按钮脉冲信号控制
校准方式
：零点和满量程校准
工作温度
： -10℃～ +40℃
工作湿度
： 10％～80％ RH
的最佳状态。当然，如果配置较高，则工作站在运行时能够更快更好地处理数据。显示器的分辨率越高，则显示的谱图越平滑。

U-POL环氧底漆技术数据表说明书

RAPTOR 2K EPOXY ANTI-CORROSIVE PRIMER 4:1 MIX••••••••Available Colours•Grey semi glossSubstrates••Mild Steel •E-coat••SMC• Polyester FillersBaseMixedViscosity 25 - 30 s/ DIN 4Solid content Specific gravity g/cm³1.35TECHNICAL DATA SHEETSuitable as a primer or as a primer filler for industrial refinish applications, the primer also provides excellent anti-rust protection.Excellent opacity and coverageEasy to applyChromate and Lead free Excellent anti-corrosion resistance PROPERTIESU-POL Raptor Epoxy primer is a 2K anti-corrosive VOC compliant primer with excellent salt spray resistance for application to most substrates.TECHNICAL DATAGood sandingExcellent topcoat gloss holdoutWet-on-wet process with a long open time for topcoat application 60.00%44.00%1.27surface preparation detailed belowGalvanizedAluminiumRAPTOR 2K EPOXY ANTI-CORROSIVE PRIMER 4:1 MIXTECHNICAL DATA SHEETSubstrate PreparationTo achieve best results, good preparation is essential. Degrease with U-POL Degreasers (S2000, S2001 or S2002). U-POL Epoxy Primer can be applied directly to suitably prepared rust without a requirement for chemical preparation.In all cases, loose and flaky material should be removed to ensure that the metal is returned to be a sound substrate before applying the primer.Sufficient abrasion / blasting must always to be employed to create a key to ensure adhesion of the primer.The degree of substrate preparation required depends on the severity of the prior corrosion and the exposure conditions anticipated during the coatings service life.For light corrosion / mild exposure conditions mechanical hand preparation (for example to the industry standard method SSPC-SP2 (SSI-St3)) or mechanical powertool preparation (for example to the industry standard method SSPC-SP3 (SSI-St3)) may be sufficient to prepare the surface.For heavy corrosion / severe exposure conditions, removal of rust by abrasive blasting (for example to the industry standard method SSPC-SP10 (SSI-SA2.5)) is recommended.For work which carries a warranty of performance this is the advised method, as lifetime of the coating in severe conditions is enhanced by more rigorous surface preparation. For all substrates, once abraded, clean once more with SYSTEM 20 Degreasers and dry thoroughly.Wood or plywood: dry sand with P180 -P240 to achieve a smooth surface free from loose fibresAbrade the surface as follows:For more details on surface preparation of corroded surfaces it is recommended that specialist advice is sought, eg from NACE or other similar industry body. See https:///home.aspxAluminium and Galvanized abrade with P180.U-POL Bodyfillers : dry sand with P180 - P240Please note this product is only compatible with the Epoxy Primer HardenerBare Metal (mild steel): abrade with P80.GRP, SMC, Glass fibre, Polyester Filler: dry flat with P180 P240.APPLICATION GUIDEHardener SelectionRAPTOR 2K EPOXY ANTI-CORROSIVE PRIMER 4:1 MIXTECHNICAL DATA SHEETMixing RatioStandard Application EPOXY PRIMER:Hardener25 - 30 Working Pot-Life @ 20°C2 hours4:1 by volume237.5g1080.0g 1350.0g47.5g 95.0g 142.5g 190.0g 270.0g 540.0g Viscosity DIN 4 / sec The time stated show effective life, however thematerial stays liquid for much longer but if used after this time will give unsatisfactory performanceQuantity Weight of PrimerWeight of Hardener250ml 500ml 750ml 810.0g 1000ml1250mlRAPTOR 2K EPOXY ANTI-CORROSIVE PRIMER 4:1 MIXTECHNICAL DATA SHEETCompliant HVLP Gravity GunGun tip size1.4 - 1.8mm Air Pressure at the gun1.8 -2.2 barGun tip size1.6 - 1.9mm Air Pressure at the gun3.5 -4.5 bar 2 - 3 coatsBetween coats10 mins Touch dry @ 20°C 2 hours Sandable @ 20°C 8 hours Sandable @ 60°C 30 mins Sandable @ 50°C45 minsSanding Wet Sanding by hand P500 - P600P800 - P1000Wet Sanding by machine P500 - P600P800 - P1000Dry Sanding by hand P280 - P360P400 - P500Dry Sanding by machineP280 - P360P400 - P500Wet Film Thickness approximately 140µ depending on applicationDry Film Thickness approximately 75µ depending on applicationBuild / micronsCoatsFlash-off @ 20°CDrying TimesTheoretical coverage @75µ Dry Film Thickness is approximately 5.88sq.m/ltrMethodInitial Roller ApplicationConventional spraygunFinal Apply 3 coats allowing 5 -10 minutes flash off time between coatsWet film thickness 45µ per coatDry film thickness 25µ per coatRAPTOR 2K EPOXY ANTI-CORROSIVE PRIMER 4:1 MIXTECHNICAL DATA SHEETShelf Life1 year from date of manufacture in sealed original containers.Recommended Storage Temperature5°C - 25°C Equipment CleaningImportant RemarksVOC InformationReady to use VOC g/lColourEpoxy PrimerGrey semi gloss499IMPORTANT:FOR PROFESSIONAL USE ONLY. Read full instructions before use.U-POL LtdUK SalesInternationalTechnical4th Floor, The Grange, 100 High Street T: +44 (0)20 8492 5920T: +44 (0)20 8492 5900T: +44 (0)1933 230 310London, N14 6BN F: +44 (0)20 8150 5605F: +44 (0)20 8150 5605F: +44 (0)1933 425 797**************************************************************Clean gun. Immediately after use with SYSTEM 20 thinner or gunwash.This product contains hazardous materials and therefore appropriate personal protective equipment should always be used. Please refer to the label and consult the safety data sheet for full handling instructions and personal protection information. U-POL disclaims any liability where the user does not wear the recommended personal protective equipment. The above data is for information only and may change without prior notice. It is the Buyers responsibility to ensure the suitability of the products for their own use and check the information is up to date. The recommendation of use of our products and application in our technical data sheets are based on our knowledge and experience. These data sheets are available via your local stockist or via the U-POL website at . U-POL is not responsible for the results obtained by others over whose methods we have no control and thereof U-POL is not liable for consequential or incidental damages including loss of profits.The EU limit for this product (product category: IIB.(c) in ready to use form is 540 g/litre. The VOC content of this product in ready to use form is 499 g/litre.Do not use activated product beyond pot life.Activated material should not be returned to the original can of non-activated material. After 10 minutes standing, the paint may need mild agitation to reliquify before 2nd coat.Do not apply when ambient temperature falls below 10°C or relative humidity exceeds 90%Apply only one coat of Epoxy Primer if a Polyester Filler or Polyester Spray Filler is to be applied over the Epoxy PrimerTypically the Epoxy Primer formulation is used in Industrial refinish where RAPTOR or a 2K topcoat is directly appliedThis Epoxy primer is not recommended for use with water based paint systemsAfter 60 minutes of the final coat and up to 7 days the epoxy primer can be directly overcoated with 2K polyurethanes such as U-POL RAPTOR without the need to reopen the surface by sanding. After 7 days the surface will need abrading as per the table above Wet - on - wet process @ 20°C air dryAfter 8 hours it can be overcoated with U-POL bodyfillersOver PaintingDry - on -dry process @ 20°C air dry。

unitherm38091树脂成分

unitherm38091树脂成分一、引言在涂料工业中，u nit h er m38091树脂是一种常用的材料，广泛应用于各种领域。

本文将介绍u ni th er m38091树脂的成分和特点，以帮助读者更好地了解该种树脂。

二、u n i t h e r m38091树脂的成分u n it he rm38091树脂是一种高分子聚合物，主要由以下成分组成：1.乙丙烯酸酯单体：作为主要成膜基材，具有良好的附着性和柔韧性。

2.丙烯酸乳液：作为相容剂，能提高树脂的稳定性和流变性能。

3.丙烯醇酸酯：用于调节树脂的分子量分布和固含量，影响涂膜的硬度和耐久性。

4.阻燃剂：添加适量的阻燃剂，可以增加树脂的阻燃性能，提高涂层的安全性。

5.交联剂：用于增加树脂的交联程度，提高涂层的耐化学性和耐磨性。

6.助剂：包括溶剂、消泡剂、稳定剂等，用于调节树脂的性能，并确保涂料的良好加工性。

三、u n i t h e r m38091树脂的特点u n it he rm38091树脂具有以下几个主要特点：1.优异的耐候性u n it he rm38091树脂具有良好的耐候性，能够在恶劣的户外环境下长期保持良好的表面状态，不易发生老化和脱落。

2.卓越的抗化学性能该树脂具有卓越的抗化学性能，能够承受酸、碱、盐等化学物质的侵蚀，保持涂层的完整性和耐久性。

3.良好的粘附性u n it he rm38091树脂与各种基材具有良好的粘附性，能够牢固附着在金属、木材、塑料等表面，形成坚固的涂膜。

4.超强的阻燃性在u ni th er m38091树脂中添加了阻燃剂，使其具备超强的阻燃性能，能够有效阻止火焰蔓延，提高涂层的安全性。

5.易施工该树脂具有良好的流变性能和加工性，易于施工操作。

无论是喷涂、刷涂还是滚涂，都能够得到均匀、平整的涂膜。

结论u n it he rm38091树脂是一种性能优良的涂料材料，具有优异的耐候性、抗化学性能和粘附性，同时还具备超强的阻燃性和易施工的特点。

激光直接成型LDS级树脂细分市场调研报告

09
投资机会挖掘与风险评估
投资热点区域和项目推荐
热点区域
推荐关注亚太地区，尤其是中国和印度市场。这两个国家经济增长迅速，对LDS级树脂的需求量大，且政府支持相关产业发展。
未来技术发展趋势预测
多材料复合成型技术
结合不同材料的优点，实现多材料复合成型，满足更广泛的应用需求。
绿色环保制造技术
推动环保型LDS级树脂的研发和应用，降低环境污染，提高可持续性。
ABCD
高精度、高效率制造技术
进一步提高成型精度和效率，缩短产品开发周期，降低成本。
智能化、自动化生产技术
引入人工智能、机器学习等先进技术，实现智能化、自动化生产，提高生产效率和质量。
需求特点分析
目标客户群体对LDS级树脂的需求呈现出多样化、个性化和高品质化的特点。他们不仅关注产品的基本性能，还对产品的环保性、耐候性、抗老化性等方面有着较高的要求。此外，对于产品的定制化服务和整体解决方案的需求也在逐渐增加。
营销策略制定和执行情况回顾
营销策略制定
针对目标客户群体的需求特点，我们制定了以高品质、个性化定制和整体解决方案为核心的营销策略。通过加强品牌建设、提升产品品质和服务水平，以及与行业内的合作伙伴建立紧密的合作关系，来提高产品的知名度和市场占有率。
激光直接成型LDS 级树脂细分市场调研报告
汇报人：XXX
20XX-XX-XX
目录
• 市场概述与发展趋势 • 产业链结构及主要参与者分析 • 竞争格局与主要厂商对比分析 • 产品类型及应用领域细分市场调
研 • 技术创新及研发动态追踪 • 政策法规影响及行业标准解读
目录
• 营销策略、渠道拓展及品牌建设探讨

DOWSIL TC-5622热导致片子说明书

TC-5622, 1KG TC-5622, 1KGSAFETY DATA SHEETDOWSIL™ TC-5622 Thermally Conductive CompoundVersion 1.5Revision Date:09.03.2018SDS Number:2815298-00006Date of last issue: 09.02.2017Date of first issue: 15.10.20151. PRODUCT AND COMPANY IDENTIFICATIONProduct name : DOWSIL™ TC-5622 Thermally Conductive Compound Product code : 04095430Manufacturer or supplier's detailsCompany Identification : DOW CHEMICAL INTERNATIONAL PVT. LTD.GODREJ IT PARK - P2, 1st FLOOR, BLOCK B, 02LBS ROAD, GODREJ BUSINESS DISTRICTPIROJSHANAGAR400079 VIKHROLI, MUMBAIINDIATelephone : (91) 22-6674-150024-Hour Emergency Contact : 91-22-6674-1800Local Emergency Contact : 22-6674-1800E-mail address : *******************Recommended use of the chemical and restrictions on useRecommended use : Electrical industry and electronics2. HAZARDS IDENTIFICATIONManufacture, Storage and Import of Hazardous Chemicals Rules 1989ClassificationNot classified as hazardous according to criteria laid down in Part I of Schedule-1.GHS ClassificationNot a hazardous substance or mixture.GHS label elementsNot a hazardous substance or mixture.Other hazards which do not result in classificationNone known.3. COMPOSITION/INFORMATION ON INGREDIENTSSubstance / Mixture : MixtureChemical nature : Silicone compoundSAFETY DATA SHEETDOWSIL™ TC-5622 Thermally Conductive CompoundVersion 1.5Revision Date:09.03.2018SDS Number:2815298-00006Date of last issue: 09.02.2017Date of first issue: 15.10.2015Hazardous componentsNo hazardous ingredients4. FIRST AID MEASURESIf inhaled : If inhaled, remove to fresh air.Get medical attention if symptoms occur.In case of skin contact : Wash with water and soap as a precaution.Get medical attention if symptoms occur.In case of eye contact : Flush eyes with water as a precaution.Get medical attention if irritation develops and persists.If swallowed : If swallowed, DO NOT induce vomiting.Get medical attention if symptoms occur.Rinse mouth thoroughly with water.Most important symptomsand effects, both acute anddelayed: None known.Protection of first-aiders : No special precautions are necessary for first aid responders.Notes to physician : Treat symptomatically and supportively.5. FIREFIGHTING MEASURESSuitable extinguishing media : Water sprayAlcohol-resistant foamCarbon dioxide (CO2)Dry chemicalUnsuitable extinguishingmedia: None known.Specific hazards during fire-fighting: Exposure to combustion products may be a hazard to health.Hazardous combustion prod-ucts : Carbon oxides Silicon oxidesMetal oxidesFormaldehydeSpecific extinguishing me-thods : Use extinguishing measures that are appropriate to local cir-cumstances and the surrounding environment.Use water spray to cool unopened containers.Remove undamaged containers from fire area if it is safe to do so.Evacuate area.Special protective equipment for firefighters : Wear self-contained breathing apparatus for firefighting if ne-cessary.SAFETY DATA SHEETDOWSIL™ TC-5622 Thermally Conductive CompoundVersion 1.5Revision Date:09.03.2018SDS Number:2815298-00006Date of last issue: 09.02.2017Date of first issue: 15.10.2015Use personal protective equipment.6. ACCIDENTAL RELEASE MEASURESPersonal precautions, protec-tive equipment and emer-gency procedures : Follow safe handling advice and personal protective equip-ment recommendations.Environmental precautions : Discharge into the environment must be avoided.Prevent further leakage or spillage if safe to do so.Retain and dispose of contaminated wash water.Local authorities should be advised if significant spillagescannot be contained.Methods and materials for containment and cleaning up : Soak up with inert absorbent material.For large spills, provide dyking or other appropriate contain-ment to keep material from spreading. If dyked material can be pumped, store recovered material in appropriate container.Clean up remaining materials from spill with suitable absor-bent.Local or national regulations may apply to releases and dis-posal of this material, as well as those materials and itemsemployed in the cleanup of releases. You will need to deter-mine which regulations are applicable.Sections 13 and 15 of this SDS provide information regarding certain local or national requirements.7. HANDLING AND STORAGETechnical measures : See Engineering measures under EXPOSURECONTROLS/PERSONAL PROTECTION section.Local/Total ventilation : Use only with adequate ventilation.Advice on safe handling : Handle in accordance with good industrial hygiene and safetypractice, based on the results of the workplace exposure as-sessmentTake care to prevent spills, waste and minimize release to theenvironment.Conditions for safe storage : Keep in properly labelled containers.Store in accordance with the particular national regulations.Materials to avoid : Do not store with the following product types:Strong oxidizing agents8. EXPOSURE CONTROLS/PERSONAL PROTECTIONComponents with workplace control parametersContains no substances with occupational exposure limit values.SAFETY DATA SHEETDOWSIL™ TC-5622 Thermally Conductive CompoundVersion 1.5Revision Date:09.03.2018SDS Number:2815298-00006Date of last issue: 09.02.2017Date of first issue: 15.10.2015Engineering measures : Processing may form hazardous compounds (see section 10).Ensure adequate ventilation, especially in confined areas.Minimize workplace exposure concentrations.Personal protective equipmentRespiratory protection : Use respiratory protection unless adequate local exhaust ven-tilation is provided or exposure assessment demonstrates thatexposures are within recommended exposure guidelines.Filter type : Particulates typeHand protectionRemarks : Wash hands before breaks and at the end of workday.Eye protection : Wear the following personal protective equipment:Safety glassesSkin and body protection : Skin should be washed after contact.Hygiene measures : Ensure that eye flushing systems and safety showers arelocated close to the working place.When using do not eat, drink or smoke.Wash contaminated clothing before re-use.These precautions are for room temperature handling. Use atelevated temperature or aerosol/spray applications may re-quire added precautions.9. PHYSICAL AND CHEMICAL PROPERTIESAppearance : GreaseColour : greyOdour : noneOdour Threshold : No data availablepH : Not applicableMelting point/freezing point : No data availableInitial boiling point and boilingrange: Not applicableFlash point : 265 °CMethod: Seta closed cupEvaporation rate : Not applicableFlammability (solid, gas) : Not classified as a flammability hazardSAFETY DATA SHEETDOWSIL™ TC-5622 Thermally Conductive CompoundVersion 1.5Revision Date:09.03.2018SDS Number:2815298-00006Date of last issue: 09.02.2017Date of first issue: 15.10.2015Self-ignition : The substance or mixture is not classified as pyrophoric. Thesubstance or mixture is not classified as self heating.Upper explosion limit / Upperflammability limit: No data availableLower explosion limit / Lowerflammability limit: No data availableVapour pressure : Not applicableRelative vapour density : No data availableRelative density : 2.55Solubility(ies)Water solubility : No data availablePartition coefficient: n-octanol/water: No data availableAuto-ignition temperature : No data availableDecomposition temperature : No data availableViscosityViscosity, dynamic : Not applicableExplosive properties : Not explosiveOxidizing properties : The substance or mixture is not classified as oxidizing.Molecular weight : No data availableParticle size : No data available10. STABILITY AND REACTIVITYReactivity : Not classified as a reactivity hazard.Chemical stability : Stable under normal conditions.Possibility of hazardous reac-tions : Use at elevated temperatures may form highly hazardous compounds.Can react with strong oxidizing agents.Hazardous decomposition products will be formed at elevated temperatures.Conditions to avoid : None known. Incompatible materials : Oxidizing agentsSAFETY DATA SHEETDOWSIL™ TC-5622 Thermally Conductive CompoundVersion 1.5Revision Date:09.03.2018SDS Number:2815298-00006Date of last issue: 09.02.2017Date of first issue: 15.10.2015Hazardous decomposition productsThermal decomposition : BenzeneFormaldehyde 11. TOXICOLOGICAL INFORMATIONInformation on likely routes of exposure : Skin contact IngestionEye contactAcute toxicityNot classified based on available information.Skin corrosion/irritationNot classified based on available information.Serious eye damage/eye irritationNot classified based on available information.Respiratory or skin sensitisationSkin sensitisationNot classified based on available information.Respiratory sensitisationNot classified based on available information.Germ cell mutagenicityNot classified based on available information.CarcinogenicityNot classified based on available information.Reproductive toxicityNot classified based on available information.STOT - single exposureNot classified based on available information.STOT - repeated exposureNot classified based on available information.Aspiration toxicityNot classified based on available information.12. ECOLOGICAL INFORMATIONEcotoxicityNo data availablePersistence and degradabilityNo data availableSAFETY DATA SHEETDOWSIL™ TC-5622 Thermally Conductive CompoundVersion 1.5Revision Date:09.03.2018SDS Number:2815298-00006Date of last issue: 09.02.2017Date of first issue: 15.10.2015Bioaccumulative potentialNo data availableMobility in soilNo data availableOther adverse effectsNo data available13. DISPOSAL CONSIDERATIONSDisposal methodsWaste from residues : Dispose of in accordance with local regulations.Contaminated packaging : Empty containers should be taken to an approved waste han-dling site for recycling or disposal.If not otherwise specified: Dispose of as unused product. 14. TRANSPORT INFORMATIONInternational RegulationsUNRTDGNot regulated as a dangerous goodIATA-DGRNot regulated as a dangerous goodIMDG-CodeNot regulated as a dangerous goodTransport in bulk according to Annex II of MARPOL 73/78 and the IBC CodeNot applicable for product as supplied.15. REGULATORY INFORMATIONSafety, health and environmental regulations/legislation specific for the substance or mix-tureThe components of this product are reported in the following inventories:NZIoC : All ingredients listed or exempt.REACH : For purchases from Dow Chemical EU legal entities, all ingre-dients are currently pre/registered or exempt under REACH.Please refer to section 1 for recommended uses. For pur-chases from non-EU Dow Chemical legal entities with theintention to export into EEA please contact your DC repre-sentative/local office.IECSC : All ingredients listed or exempt.ENCS/ISHL : All components are listed on ENCS/ISHL or exempted fromSAFETY DATA SHEETDOWSIL™ TC-5622 Thermally Conductive CompoundVersion 1.5Revision Date:09.03.2018SDS Number:2815298-00006Date of last issue: 09.02.2017Date of first issue: 15.10.2015inventory listing.DSL : This product contains one or more substances which are noton the Canadian Domestic Substances List (DSL). Import ofthis product into Canada has volume limitations. For volumelimits please consult Dow Chemical Regulatory Compliance.TSCA : All chemical substances in this product are either listed on theTSCA Inventory or are in compliance with a TSCA Inventoryexemption.AICS : Consult your local Dow Chemical office.KECI : All ingredients listed, exempt or notified.PICCS : All ingredients listed or exempt.TCSI : All ingredients listed or exempt.16. OTHER INFORMATIONFurther informationSources of key data used to compile the Safety Data Sheet : Internal technical data, data from raw material SDSs, OECD eChem Portal search results and European Chemicals Agen-cy, http://echa.europa.eu/Items where changes have been made to the previous version are highlighted in the body of this document by two vertical lines.Date format : dd.mm.yyyyFull text of other abbreviationsAICS - Australian Inventory of Chemical Substances; ANTT - National Agency for Transport by Land of Brazil; ASTM - American Society for the Testing of Materials; bw - Body weight; CMR - Carcinogen, Mutagen or Reproductive Toxicant; CPR - Controlled Products Regulations; DIN - Standard of the German Institute for Standardisation; DSL - Domestic Substances List (Canada); ECx - Concentration associated with x% response; ELx - Loading rate associated with x% re-sponse; EmS - Emergency Schedule; ENCS - Existing and New Chemical Substances (Japan); ErCx - Concentration associated with x% growth rate response; ERG - Emergency Response Guide; GHS - Globally Harmonized System; GLP - Good Laboratory Practice; IARC - Internation-al Agency for Research on Cancer; IATA - International Air Transport Association; IBC - Interna-tional Code for the Construction and Equipment of Ships carrying Dangerous Chemicals in Bulk; IC50 - Half maximal inhibitory concentration; ICAO - International Civil Aviation Organization; IECSC - Inventory of Existing Chemical Substances in China; IMDG - International Maritime Dan-gerous Goods; IMO - International Maritime Organization; ISHL - Industrial Safety and Health Law (Japan); ISO - International Organisation for Standardization; KECI - Korea Existing Chemi-cals Inventory; LC50 - Lethal Concentration to 50 % of a test population; LD50 - Lethal Dose toSAFETY DATA SHEETDOWSIL™ TC-5622 Thermally Conductive CompoundVersion 1.5Revision Date:09.03.2018SDS Number:2815298-00006Date of last issue: 09.02.2017Date of first issue: 15.10.201550% of a test population (Median Lethal Dose); MARPOL - International Convention for the Pre-vention of Pollution from Ships; n.o.s. - Not Otherwise Specified; Nch - Chilean Norm; NO(A)EC - No Observed (Adverse) Effect Concentration; NO(A)EL - No Observed (Adverse) Effect Level; NOELR - No Observable Effect Loading Rate; NOM - Official Mexican Norm; NTP - National Tox-icology Program; NZIoC - New Zealand Inventory of Chemicals; OECD - Organization for Eco-nomic Co-operation and Development; OPPTS - Office of Chemical Safety and Pollution Preven-tion; PBT - Persistent, Bioaccumulative and Toxic substance; PICCS - Philippines Inventory of Chemicals and Chemical Substances; (Q)SAR - (Quantitative) Structure Activity Relationship; REACH - Regulation (EC) No 1907/2006 of the European Parliament and of the Council concern-ing the Registration, Evaluation, Authorisation and Restriction of Chemicals; SADT - Self-Accelerating Decomposition Temperature; SDS - Safety Data Sheet; TCSI - Taiwan Chemical Substance Inventory; TDG - Transportation of Dangerous Goods; TSCA - Toxic Substances Con-trol Act (United States); UN - United Nations; UNRTDG - United Nations Recommendations on the Transport of Dangerous Goods; vPvB - Very Persistent and Very Bioaccumulative; WHMIS - Workplace Hazardous Materials Information SystemThe information provided in this Safety Data Sheet is correct to the best of our knowledge, infor-mation and belief at the date of its publication. The information is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal and release and shall not be considered a warranty or quality specification of any type. The information provided relates onlyto the specific material identified at the top of this SDS and may not be valid when the SDS ma-terial is used in combination with any other materials or in any process, unless specified in the text. Material users should review the information and recommendations in the specific context of their intended manner of handling, use, processing and storage, including an assessment of the appropriateness of the SDS material in the user’s end product, if applicable.IN / ENTC-5622, 1KG TC-5622, 1KG。

UTR9000-联泰SLA树脂资料(汇编)

它被用于固态激光的光固化成型法。

UTR9000可应用于于汽车，医疗，消费电子等工业领域的母模，概念模型，一般部件，功能性部件的制作。

用UTR9000树脂制造的部件的耐久性长达6.5个月以上。

TYPICAL FEATURES典型特点-Liquid resin`s medium viscosity, so easy recoating, easy clean parts and machines 中等粘度的液态树脂，确保其更容易涂层以及清洗部件和机器-Improved strength retained, improved dimensions retention of parts in humid condition 在潮湿环境中具有更好的强度及尺寸保持特性-need minimal part finishing只需要极小的部件修饰-Long shelf life in machine更长的实际使用期限TYPICAL BENEFITS典型优点-Need less part finishing time,easier post-curing 更少的部件完成时间-Buliding accurate and high tough parts with an improved dimensional stability 能够建造精确和高韧性的部件并提高了部件的尺寸稳定性-High quality controls for vacuum casting parts 对于真空铸造部件的高质量控制-Low shrink and good resistance to yellowing 低收缩和优异的耐黄变性-Magnificent white color 华丽的白色外观-Outstanding machinable SLA material 卓越的可加工性Physical Properties – Liquid Material 液态材料的物理性能Appearance外观White白色Density 密度1.13g/cm3 @ 25 ℃Viscosity 粘度355 cps @ 28 ℃0.145 mmDp 固化深度9.3 mJ/cm2Ec 临界曝光量Building layer thickness0.1mm建造层厚Mechanical Properties of Post-Cured Material 固化后材料的机械性能MEASUREMENT测试项目TEST METHOD 测试方法V ALUE 数值90-minute UV post-cure 90分钟紫外固化Hardness 硬度, Shore D ASTM D 2240 83Flexural modulus 弯曲模量, Mpa ASTM D 790 2,692-2,775Flexural strength 弯曲强度, Mpa ASTM D 790 69- 74Tensile modulus 拉伸模量, MPa ASTM D 638 2,189-2,395Tensile strength 拉伸强度, MPa ASTM D 638 27-31Elongation at break 断裂延长率ASTM D 638 12 -20%Impact strength,notched lzod, J/mASTM D 256 58 - 70缺口冲击强度ASTM D 648 @66PSI 52Heat deflection temperature, ℃热变形温度Glass transition,Tg玻璃化转变温度，℃DMA，E”peak 62Coefficient of thermal expension,热膨胀系数, /℃TMA(T<Tg) 97*E-6Density 密度, g/cm3 1.16注：使用温度和保存温度不宜过高，请在25摄氏度以下使用；推荐使用和保存温度为18-25摄氏度。

200907--OKP树脂绍介(中文版修正)★★

1.61000 -20
0
10
0
20
40
60
80
温度/℃
温度/℃
20
30
40
50
60
70
587.6（d線） 1.6361 1.6350 1.6339 1.6328 1.6317 1.6306 1.6294 1.6283 1.6270
656.3（C線） 1.6284 1.6273 1.6262 1.6252 1.6241 1.6230 1.6218 1.6207 1.6194
折射率温度依存性
OKP4
1.65000 1.64000
1.63000
折射率1.62000
1.61000
587.6nm 656.3nm 546.1nm 486.1nm 435.8nm
1.60000
波長/nm
587.6（d線） 656.3（C線） 546.1（e線） 486.1（F線） 435.8（g線）
600
400
200
0
0
5
10
15
20
乾燥時間 / h
OKP4HT
2000
13820000
真空條件時
13600000
2800
建議乾燥温度為 80～90℃
12460000
5 小時以上
常壓條件時建議乾燥温度為 90～100℃
12240000
ppm 2200 量/ 12000000 水分ppm 1880000 / 1600 量 600 水分1400
目視確認甲苯
×
×
無變化：○ 環己烷
○
○
白化：× 丙酮
×
×
※ 以上數據非保證値。

迈图高新材料集团有机硅树脂介绍 - 080304 Xian

An introduction of Momentive Silicone Resin 迈图高新材料集团有机硅树脂介绍
- Momentive Peformance Materials - 迈图高新材料集团 - 22/Nov./2007
1
CONTENTS 内容
- What is a silicone? 什么是有机硅? - Manufacture of Silicones 有机硅树脂的生产 - Silicone Basic Element 有机硅树脂基本结构 - Why Silicone Paints ? 为什么使用有机硅树脂? - Silicone Features & Benefits 有机硅树脂特点和优点 - Structure /performance relationship 有机硅树脂结构与性质的关系 - Cure Systems of Silicone Resins 有机硅树脂的固化 - Momentive Typical Silicone Resins 迈图公司典型的有机硅树脂产品 -Silicone application 有机硅树脂的应用 - Pure silicone resin 纯有机硅树脂 - Modified silicone resin 改性有机硅树脂 - Silicone oligomer 有机硅低聚物 - Spherical silicone resin 球形有机硅树脂 - Any Time, Please Contact Us 随时恭候您的咨询
Resistance for oxidation 耐氧化
Why Silicone Paints ? 为什么使用有机硅树脂？
共价键
ーOーSi－O－Si－O－SiーO－Siー R
Si-O-Si : 自由基反应惰性 : 离子反应敏感 Si-R : 低反应活性

METTLER-TOLEDO BBA4x9 规格表说明书

Data Brief BBA429 – BBA439check – BBA449check+Colourful tolerance control – for reliableresultsPicture: BBA449check-A15Fast and precise results. With the METTLER TOLEDO BBA4x9 checkweighing scales you have everything under control all the time!IP69K protectedComplete stainless steel enclosure Weights and measures approved for Class IIIEHEDG and NSF compliant designGMP certifiedTechnical dataMaterial Chrome-nickel-steel (AISI 304, 1.4301) Ambient temperature -10° to +40°C for Class III Humidity Up to 80% rel., non condensing Level Up to 2000m above sea level, indoors Weight (net) BBA4x9-A: approx. 9.0 kgBBA4x9-BB: approx. 12.1 kgBacklit, 7-digit, 7-segment LC-DisplayCharacter height 16mm (BBA429), 21mm (BBA439check,BBA449check+)Units of weight g, kg, t, oz, lbMetrology NTEP, OIMLHygiene NSF, EHEDGPharma industry GMPElectrical Safety CSA – C US, CE, PSE (pending)IP Protection IP69K (DIN 40050)Standard AC power supply 100 to 240 V AC, 47 to 63 Hz, 300 mAPower cord: approx. 2.3 m long Optional 12 to 24 VDC connection, 1.0AOptional battery operationCharger 100 to 240 V AC, 47 to 63 Hz, 300 mAPower cord: approx. 2.3 m long Operation time 9h typ. (continuous operation)90h typ. (“power off mode” 1 min) Charging time 6h typ.Life time 1000 charge-/ discharge cycles typ. Built-in options and peripherals reduce operation time!Material Polyester (PE)Number of keys(keys with tactile feedback) BBA429: 6BBA439check: 10BBA449check+: 25FunctionalityFunctions BBA429 BBA439check BBA449check+Zero setting ●●●Taring ●●●Change of unit ●●●Printing /data transfer ●●●MinWeigh ●●●Counting --●Info --●Identification (2 values) - - ●Date / time - - ●Tare definition - - ●Checkweighing -●●Numeric display ●●●± application (check, check+) - ●●Bargraph ± display - ●●Colored ± display (colorWeight®) - ●●Input modes for target weights - 3 3Input modes for target quantities - - 2Classify (5 classes) - - ●Standard tolerances - ●●«Take-away» mode - - ●Memory for ± data records - 99 99Memory for classification parameters - - 99Battery operation (optional) ●●●InterfacesStandard RS232RS232RS422 / RS485EthernetUSB (Slave)Digital I/O (4 In / 4 Out)Optional: one moreinterface:Wireless LANThe interfaces are accessible via IP69K protected receptacles at the rear side of theterminalAnalogue weighing technologyStandard integrated A/D converter / 1 built-inhermetically sealed stainless steel load cellResolution (approvable OIML classIII)2 x 3000eModel A B C D E F A 300 102.5 235 240 175 380 BB400 104.5 335 300 235 4504 digital In galvanically isolated via opto coupler external: 1 mA (min.5 V DC)8 mA (max. 30 V DC)internal: 3 mA (at 12 V DC)BBA429 BBA439check BBA449check+On / Off ● ● ●Zero setting ● ● ●Taring ● ● ●Printing / transfer ● ● ●Clearing (Clear key) ● - ●Unit switching ● ● ●Info key - - ●ID1, ID2/REF key - - ●Target key - ● ●Recall key - ● ●Save key - ● ●Arrow right - ● -Arrow up - ● - Arrow down - ● - TakeAway key - - ● 4 digital Out Galvanically isolated via relay contacts external: 500 mA (max. 30 V DC) per outinternal: 400 mA (bei 12 V DC) total outs 1 (4)BBA429 BBA439check BBA449check+Stable weight ● ● ● < / ≥ MinWeigh ● ● ● Overload / underload ● ● ● Display asterisk ● ● ● < tolerance - - ● ● Inside tolerance - ● ●Target weight - ● ●≥ tolerance + - ● ●Class 1…5 - - ●GA46-thermal printer, stainless steel, RS232 interface, 2.5m cable incl. 00505471GA46- thermal printer, stainless steel, RS232 interface, 0.4m cable incl. 00507229GA46-W-thermal printer, stainless steel, RS232 interface, 2.5m cable incl., IP65, protective cover, winder.00505799GA46-W-thermal printer, stainless steel, RS232 interface, 0.4m cable incl., IP65, protective cover, winder.00507230 ADI419 auxiliary display, stainless steel (IP69K, RS232, 3m cable incl., display without backlit)22013962 ADI419 auxiliary display, stainless steel (IP69K, RS232, 3m cable incl., display with backlit)22014022 RS232 – cable SICS second scale (3m, 8pin <-> 9pin Sub D plug) 22006795 RS232 - cable for PC (3m, 8pin <-> 9pin Sub D female connector) 00504376RS232 counter plug, 8 pin 00503756 RS422/RS485 - cable (3m, 6pin <-> open ends) 00204933 RS485 counter plug, 6 pin 00204866 Ethernet 10/100 Base T twisted pair cable (5m -> 8pin RJ45) 00205247 Ethernet 10/100 Base T twisted pair cable (20m -> 8pin RJ45) 00208152 USB adapter cable (0.2m -> USB series A female connector) 22006268 USB adapter cable (3m -> USB series A female connector) 22007713 USB cable (3m -> USB series A female connector) 22015326 Relay box for digital I/O option (as for IND690) 22011967 Cable digital I/O option and relay box (10m) 00504458 Power supply for Relay Box ( 110-230 V AC) 00505544 Digital I/O counter plug, 19 pin 00504461 Protective cover for compact scale BBA4x9 (Set with 3 pieces) 22013992 External battery, stainless steel, IP69K (without charger) 22013988 Charger for external battery 22014056 SICS reference manual 4 Series 22011459 BBA429, BBA439check, BBA449check+ Model Capacity Resolution Order number BBA429 - A 31.5kg / 3kg 0.5g/1g 22015010 BBA429 - A 6 3kg / 6kg 1g/2g 22014800 BBA429 - A 15 6kg / 15kg 2g/5g 22014801 BBA429 - BB 30 15kg / 30kg 5g/10g 22014802 BBA439check - A 31.5kg / 3kg 0.5g/1g 22015011 BBA439check - A 6 3kg / 6kg 1g/2g 22014803 BBA439check - A 15 6kg / 15kg 2g/5g 22014804 BBA439check - BB 30 15kg / 30kg 5g/10g 22014805 BBA449check+ - A 3 1.5kg / 3kg 0.5g/1g 22015012 BBA449check+ - A 6 3kg / 6kg 1g/2g 22014806 BBA449check+ - A 15 6kg / 15kg 2g/5g 22014807 BBA449check+ - BB 30 15kg / 30kg 5g/10g 22014808 Standard resolution 2 x 3000d (non approvable) 2 x 3000e (approved) 1 x 6000d (non approvable) 1 x 15000d (non approvable) Optional resolution 1 x 30000d (non approvable)。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

UTR9000 TECHNICAL DATA SHEET PRODUCT DESCRIPTION 产品介绍
C-UV 9400 is an ABS like SL resin which has accurate and durable features. It is designed for solid state SLA platforms. C-UV 9400 can be applied in master patterns, concept models, general parts and functional prototypes in the field of automotive, medical and consumer electronics industries.The parts duability building with UTR9000is over 6.5months.UTR9000 是一种具备精确和耐久特性的类ABS的立体光造型树脂。

它被用于固态激光的光固化成型法。

UTR9000可应用于于汽车，医疗，消费电子等工业领域的母模，概念模型，一般部件，功能性部件的制作。

用UTR9000树脂制造的部件的耐久性长达6.5个月以上。

TYPICAL FEATURES典型特点
-Liquid resin`s medium viscosity, so easy recoating, easy clean parts and machines 中等粘度的液态树脂，确保其更容易涂层以及清洗部件和机器
-Improved strength retained, improved dimensions retention of parts in humid condition 在潮湿环境中具有更好的强度及尺寸保持特性
-need minimal part finishing只需要极小的部件修饰
-Long shelf life in machine更长的实际使用期限
TYPICAL BENEFITS典型优点
-Need less part finishing time,easier post-curing 更少的部件完成时间
-Buliding accurate and high tough parts with an improved dimensional stability 能够建造精确和高韧性的部件并提高了部件的尺寸稳定性
-High quality controls for vacuum casting parts 对于真空铸造部件的高质量控制
-Low shrink and good resistance to yellowing 低收缩和优异的耐黄变性
-Magnificent white color 华丽的白色外观
-Outstanding machinable SLA material 卓越的可加工性
Physical Properties – Liquid Material 液态材料的物理性能
Appearance外观
White白色
Density 密度
1.13g/cm3 @ 25 ℃
Viscosity 粘度355 cps @ 28 ℃
0.145 mm
Dp 固化深度
9.3 mJ/cm2
Ec 临界曝光量
Building layer thickness
0.1mm
建造层厚
Mechanical Properties of Post-Cured Material 固化后材料的机械性能
MEASUREMENT测试项目TEST METHOD 测试方法V ALUE 数值
90-minute UV post-cure 90分钟紫外固化Hardness 硬度, Shore D ASTM D 2240 83
Flexural modulus 弯曲模量, Mpa ASTM D 790 2,692-2,775
Flexural strength 弯曲强度, Mpa ASTM D 790 69- 74
Tensile modulus 拉伸模量, MPa ASTM D 638 2,189-2,395
Tensile strength 拉伸强度, MPa ASTM D 638 27-31
Elongation at break 断裂延长率ASTM D 638 12 -20%
Impact strength,notched lzod, J/m
ASTM D 256 58 - 70
缺口冲击强度
ASTM D 648 @66PSI 52
Heat deflection temperature, ℃
热变形温度
Glass transition,Tg
玻璃化转变温度，℃DMA，E”peak 62
Coefficient of thermal expension,
热膨胀系数, /℃TMA(T<Tg) 97*E-6
Density 密度, g/cm3 1.16
注：使用温度和保存温度不宜过高，请在25摄氏度以下使用；推荐使用和保存温度为18-25摄氏度。