SGM3780 REV.A_20130820

合集下载

SyncSystem 4380A输入输出和测量模块说明书

Input/Output and Measurement ModulesThe rear of the SyncSystem 4380A is shown below. Modules can be operated in any of the six slots. The unit will automatically detect and configure the system based on the modules(s) installed. The module slots are identified by slot number so the operator can identify the modules' physical location in the chassis.Pulse Output Modules4394A: Pulse output (e.g., PPS, DC-IRIG), 4 ports, BNC(F)The 4394A module provides 4 pulse output ports. The output type of each port is individually user configurable. Users can change the signal types (PPS / DC IRIG), the PPS signal parameters, and the IRIG signal parameters. The 4394A module is tied to the UTC Epoch only.DescriptionSFP Ports (future use)10 MHz InputUSBEthernet GNSS Antenna In put6 hot-swappable expansion slotssupport a broad range of input/output modules4334A: Pulse output (e.g., PPS, DC-IRIG) - UTC Time and GPS TimeThe 4334A module provides two 1PPS outputs and two DC IRIG (B000) outputs.Outputs 1 and 2 are 1PPS and outputs 3 and 4 are DC IRIG. Users can changethe signal types (PPS/DC IRIG/Havequick), the PPS signal parameters, theIRIG signal types on individual output ports with 4 independent epochs, orHavequick (UTC Only). Users can select the output voltage on each port (0-3V or0-5V) based on the configuration. By default, the module ships set to 3V.4344A: 1PPS-10V Output ModuleThe factory default for this module provides four 1PPS outputs at 10V 0-PK. Valid PPS settings are 1PPS to 10MPPS. This module also allows configuration of the pulse period, pulse width and PPS rates.4391A/4331A : Code GeneratorsThe 4391A/4331A Code Generators can generate user defined bit streams witha known relationship to UTC. The code generation segment uses the local UTC estimate and a user-generated data file and produces a bit stream (derived from the user-generated file) whose first bit is aligned to within 1 ns of the local UTC estimate. On the 4391A Ports 1 and 2 are TTL into 50Ω and Ports 3 and 4 are >2.4V peak-to-peak into 50Ω (NRZ). On the 4331A Ports 1 - 4 are RS422 (1.5 V to 5.5V into 100Ω differential Triax). All 4 ports of each module are in phase.4391A: Code Generator Module4331A: RS-422 Code Generator Module4376A: Pulse Output Module (e.g., PPS, DC-IRIG), RS-422 (4 outputs), DB15(F) The 4376A module factory default for this module provides four 1PPS outputsusing a DB15 type connector. Users can change the PPS signal parameters onindividual signal outputs.4335A: Pulse, Timecode, Have Quick Output ModuleThe 4335A module provides two 1PPS outputs and two DC IRIG (B000) Outputs.Outputs 1 and 2 are 1PPS and Outputs 3 and 4 are DC IRIG. The output types areuser selectable/programmable. Users can change the signal types (PPS/DC IRIG/Havequick), the PPS signal parameters, the IRIG signal types on individual outputports with 4 independent epochs, or Havequick (UTC Only). Users are able toselect the output voltage on each port (0-3V or 0-5V) based on the configuration.Frequency Output ModulesThe SyncSystem 4380A supports a variety of frequency outputs modules. All mod-ules are all hot-swappable and do not require end user programming or configura-tion. The modules operate in any of the 6 module slots and output 10 MHz, 5 MHz or 1 MHz at +13 dbm.4395B-1: 1 MHZ Module4395B-5: 5 MHz Module4395B-10: 10 MHz ModuleAM IRIG Modules Array 4387A: Amplitude Modulated (AM) IRIG ModuleThis module provides four Amplitude Modulated (AM) IRIG Outputs or the NASA36Serial Time Code. Valid AM IRIG Codes are A (130, 133, 137), B (120, 123, 127), E (111,112, 121), G (141, 142, 147), and H (111, 112, 121, 122, 127). The default time code isB120. The 4387A-6V module provides 6 Vpp output signals.4337A and 4338A: Epoch Adjusted Timecode (AM) IRIG ModulesThis 4337A module provides four Amplitude Modulated (AM) IRIG Outputs tied to a single epoch where as the 4338A moduleallows each port to have its own unique epoch. The epoch can be user defined, UTC (default) [±offset], GPS time, or a configuredtime zone. Valid AM IRIG Codes are A (130, 133, 137), B (120, 123, 124, 127), E (111, 112, 121), G (141, 142, 147), and H (111, 112,121, 122, 127). The default time code is B120. B120 and B124 support the IEEE-1344 Control Functions.The [+/- offset] option with the UTC epoch allows users to add or subtract between 1 minute and 23 hours and 59 minutes fromthe current UTC Time. The GPS epoch outputs the GPS time scale (UTC with the current # of leap-seconds removed).A Time Zone Epoch can be specified and the IRIG Outputs will be set to that Time Zone and if the Control Function is set to 1344 the offset bits will indicate the direction and amount of time off from UTC (except for the three time zones occurring 45 minutes after the hour) and the Time Zones east of the GMT meridian (positive) or west of the GMT meridian (negative). For local offset control bits to be correct, hours must be between -15 and +15, minutes must be 0 or 30, and seconds must be zero. When a local time zone is specified, daylight savings time rules (if any) are applied automatically.each port.Communication/Telecom Modules4374A: T1/E1 Telecom ModuleThe 4374A module produces a 1.544 Mbps T1 (DS-1) or 2.048 Mbps compatibleoutput. Each port can independently be set to one of four output configurationoptions:0: B8ZS, ESF packets1: 1.544 MHz Square Wave2: B8ZS, D4 packets, All 1's3: B8ZS, D4 packets4: E1 HDB3 Framing5: 2.048 MHz Square Wave4332A: Time-of-Day (TOD) ModuleThis 4-port module can be used to serve as a reference input to devices such as the BlueSky™ GNSS Firewall, TimeProvider ® 4100, or other hardware. The outputs from this module support two sets of differential signals: 1PPS and Time-of-Day (TOD) as a serial time code. The default output format for the TOD card is ITU G8271.The 1PPS signal is on Pins 3 and 6 (Ground on Pins 4 and 5) and the TOD Signal ison Pins 7 and 8 on each RJ-45 connection.Input and Measurement Modules4382A: Phase Input Measurement ModuleThe 4382A is a four-channel phase measurement module capable of measuring the phase of 5 MHz or 10 MHz signals to high precision. The 4382A includes a multiple mixer measurement system all contained on a single plug-in card. The 4382A module measures the phase difference between an RF signal from the clock under test and a reference RF signal. The 4382A module can be configured to use the internal timebase of the SyncSystem 4380A or one of the four ports of the module can be configured as the reference RF signal. The SyncSystem 4380A uses measured IF phase differences tocompute input phase at a resolution of better than 100 femtoseconds.4393A Time Interval Counter (TIC) ModuleThis module has four input ports that can be used to measure the time interval between the internal 1PPS and up to four external sources and will work in any of the 6 module slots. The averaging period for the measurements is configurablefrom 1, 10, 20, 60, to 300 seconds.4383A: Time Interval Counter (TIC) ModuleThis module has four input ports that can be used to recover time from an IRIGtime source. Ports 1 and 2 support DC IRIG (Default B007) and Ports 3 and 4 sup-port AM IRIG (Default B127).The Microchip name and logo and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. All other trademarks mentioned herein are property of their respective companies.© 2022, Microchip Technology Incorporated and its subsidiaries. All Rights Reserved. 4/22 DS00004401A。

赛德凯斯电子KW系列匀胶机配件选型手册说明书

北京赛德凯斯电子有限责任公司KW系列匀胶机配件选型手册2014.11V1版SC-5-7(5mm-7mm)----------------------------------------1 SC-8-10(8mm-10mm)--------------------------------------2 SC-11-13(11mm-13mm)-----------------------------------3 SC-14-18(14mm-18mm)-----------------------------------4 SC-19-23(19mm-23mm)-----------------------------------5 SC-24-28(24mm-28mm一寸片托)-------------------------6 SC-29-33(29mm-33mm)-----------------------------------7 SC-34-38(34mm-38mm)-----------------------------------8 SC-39-43(39mm-43mm)-----------------------------------9 SC-44-48(44mm-48mm)----------------------------------10 SC-49-53(49mm-53mm二寸片托)------------------------11 SC-54-58(54mm-58mm)----------------------------------12 SC-59-63(59mm-63mm)----------------------------------13 SC-64-68(64mm-68mm)----------------------------------14 SC-70-74(70mm-74mm)----------------------------------15 SC-75-79(75mm-79mm三寸片托)------------------------16 SC-80-84(80mm-84mm)----------------------------------17 SC-85-89(85mm-89mm)----------------------------------18 SC-97-101(97mm-101mm四寸片托)----------------------19 SCS-9-13(9mm-13mm)------------------------------------20 SCS-14-18(14mm-18mm盖玻片)--------------------------21 SCS-19-23(19mm-23mm)----------------------------------22 SC-24-28-75-79(载玻片)------------------------------------23 SCL-5-44----------------------------------------------------24 SCH-44-68--------------------------------------------------25 SCH-70-84--------------------------------------------------26 SCH-80------------------------------------------------------27圆片直径：80-84mm 选择片托示意说明KW系列匀胶机配件内部编号i c s C o ., L t d适用于：方片边长范围85-89mm 圆片直径：85-89mm选择片托示意说明KW系列匀胶机配件内部编号n i c s C o ., L t dtL,.oCscino圆片直径：97mm-101mm标准4寸圆片片托选择片托示意说明KW系列匀胶机配件内部编号SC-97-101第 19 頁，共 27 頁适用于：方片边长范围19-23mmSCS-19-23选择片托示意说明KW系列匀胶机配件内部编号北京赛德凯斯电子有限责任公司第 22 頁，共 27 頁适用于：用于客户定制边长或直径44mm-68mm之间片子SCH-44-68选择片托示意说明KW系列匀胶机配件内部编号第 25 頁，共 27 頁SCH-70-84适用于：客户定制边长或直径范围：70-84mm选择片托示意说明KW系列匀胶机配件内部编号第 26 頁，共 27 頁适用于：用于客户定制边长或直径大于80mm以上片子SCH-80选择片托示意说明KW系列匀胶机配件内部编号第 27 頁，共 27 頁。

深圳市富满电子集团股份有限公司 FM3783 低功耗原边反馈开关电源芯片说明书

FM3783(文件编号：S&CIC1593)低功耗原边反馈开关电源芯片概述FM3783是一款低功耗原边反馈（PSR）开关电源芯片，其内部集成了大功率BJT管，适用于隔离型的高效低功耗便携式设备充电器应用。

FM3783采用独特具有恒流恒压功能的原边反馈控制技术，以及独特的轻载调频技术降低轻载下芯片自身功耗实现高效应用。

FM3783具有输出线损补偿技术，在大电流下保证足够的输出功率。

另外FM3783还集成了过温保护，VCC欠压保护，输出过压保护，C极开路保护等技术。

FM3783采用紧凑的SOP-7封装，便于系统设计布线。

特点集成大功率BJT管高精度恒压恒流控制待机功耗小于75mw输出短路保护输出过压保护输入欠压保护过温保护原边反馈外围元器件少SOP-7封装应用手机等便携式设备的充电器和适配器LED驱动电源其他辅助电源FM3783A适用5V2.1A方案满足六级能效标准FM3783B适用5V2.4A方案满足六级能效标准引脚示意图及说明SOP-7FM3783(文件编号：S&CIC1593)低功耗原边反馈开关电源芯片典型应用电路图典型应用电路图1典型应用电路图2FM3783(文件编号：S&CIC1593)低功耗原边反馈开关电源芯片典型应用电路图3典型应用电路图4FM3783(文件编号：S&CIC1593)低功耗原边反馈开关电源芯片典型应用电路图5注：部分PCB Layout不是很规范的客户原理图建议使用图3、4、5。

极限参数(注1)注1：最大极限值是指超出该工作范围，芯片有可能损坏。

注2：最大允许功耗为P DMAX=(T JMAX-T A)/θJA或是极限范围给出的数字中比较低的那个值。

注3：人体模型(HBM)，100pF电容通过1.5KΩ电阻放电。

FM3783(文件编号：S&CIC1593)低功耗原边反馈开关电源芯片电气参数(注4,5,6)（无特别说明情况下，V CC=16V,T A=25℃）注4：电气参数定义了器件在工作范围内并且在保证特定性能指标的测试条件下的直流和交流电参数规范。

ARTISAN技术集团设备购买与售卖说明书

ErrataTitle & Document Type:Manual Part Number:Revision Date:HP References in this ManualThis manual may contain references to HP or Hewlett-Packard. Please note that Hewlett-Packard's former test and measurement, semiconductor products an d chemical analysisbusinesses are now part of Agilent Technologies. We have made no changes to thismanual copy. The HP XXXX referred to in this document is now the Agilent XXXX.For example, model number HP8648A is now model number Agilent 8648A.About this ManualWe’ve added this manual to the Agilent website in an effort to help you support yourproduct. This manual provides the best information we could find. It may be incomplete or contain dated information, and the scan quality may not be ideal. If we find a bettercopy in the future, we will add it to the Agilent website.Support for Your ProductAgilent no longer sells or supports this product. You will find any other availableproduct information on the Agilent Test & Measurement website:Search for the model number of this product, and the resulting product page will guideyou to any available information. Our service centers may be able to perform calibrationif no repair parts are needed, but no other support from Agilent is available.3562A Programming Manual03562-90031October 1985Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | 。

SAMSON 3780说明书

SAMSON 3780说明书调节阀维护及操作规程DCS系统对调节阀的控制主要通过调节阀自身的电气阀门定位器完成。

我司生产线上的调节阀为德国SAMS ON调节阀，SAMSON调节阀采用智能数字阀门定位器（3780，HART协议数字通信），其控制精度高，运行稳定。

定位器的主要性能介绍如下：结构与工作原理HART电气定位器是为连接气动调节阀而设计的，它可确保阀杆位置（受控变量）与控制信号（参考变量）之间的对应关系。

它将控制装置 4至20mA的输出信号和调节调的行程相比较，并产生一个相应的压力信号作为输出变量。

为此，用户需要提供辅助气源压力1.4-6巴。

定位器辅助能源是由4到20mA参考变量信号提供。

定位器由一个感应，非接触或位移传感系统，一个由2／2-通开关阀组成的电控阀块以及一个电控单元组成。

电控单元包含两个用于处理控制算法及管理通讯的微控器.一旦实际阀门行程值（实际值）与参考变量（设定点）之间出现偏差，微控器就会产生一个二进制脉冲调制信号去控制两个 2／2通开关阀，且分别由一个指定的放大器来控制。

其中一个阀控制排气，另一个控制气源.气源阀（3）将供气（7气源压力1·46巴）送到执行器（填充）。

排气阀（将执行器排出空气流排放到大气中（排气）。

这些开关阀即可以有开关状态—一常开。

常闭—一也可产生可变宽度的单脉冲。

对于这两个受控＿阀门，阀林将会移动到与参考变连量相对应的位置。

如果没有系统偏差气源阀和排气阀都将关闭。

作为一个标准功能，定位器配有一个故障信息输出（根据DDN19Z34，NANUR标准的进制输出），用于向控制室发送故障信号。

成的激活位于定位器铰接盖上的写保护开关‘可防止设定被HART通讯修改。

作为对标准定位器型号的补充，有几个附加的选项用于扩展定位器功能。

带眼位开关的定位器为了在故障一安全电路中指示出阀门的最终位置，两个软件限位开关或两个接近开关被带强制排空功能的定位器一个控制定位器的6－24V电压信号，使得信压力施加到执行器。

sensION

sensION ™378多参数测定仪和多参数测定仪价格sensION ™378多参数测定仪标题：sensION ™378多参数测定仪sensION 系列多参数测量仪可以测量多种参数，如pH 、电导率、溶解氧、ORP （氧化还原电位）、总溶解性固体、盐度及温度等。

友好的用户界面，易于实现各种参数的转换和测量。

仪器具有温度自动补偿，自动校正的功能，使用方便而快捷。

大屏幕液晶屏（LCD ）显示测量结果。

sensION378是一款适合实验室使用的台式多参数测量仪，结构紧凑、功能强大。

此款仪器无需数据传输基座，可直接通过HachLinkTM 软件将数据下载至计算机。

技术指标：显示方式：液晶显示屏（LCD ）输入：（1）哈希pH/mV/温度 5针连接头（2）哈希电导率或溶解氧探头的 5针连接头输出：通过电源座连接的RS232缆线电源配置：6-12V 直流电源，可使用哈希公司提供的外部电源，也可使用用户自行提供的电源环境要求...厂家：上海政泓市场价格：优惠价格：百度搜索联系QC8500流动注射(FIA)分析仪标题：QC8500流动注射(FIA)分析仪流动注射（Flow Injection Analysis ）分析技术是丹麦科学家于1974年创立的一项分析测试技术。

它具有分析速度快、准确度和精密度高、设备操作简单、通用性强、试样和试剂用量少等一系列优点。

流动注射分析技术已经广泛应用于环境监测、医药和临床化验、工业在线分析等领域，同时也应用于化学反应动力学机理、络合物的形成过程及生化反应等理论的研究。

HACH 公司生产的Quickchem 8500（简称QC8500）型流动注射（FIA ）分析仪，采用模块化设计，根据样品的分析流程，分为以下几个单元模块：自动取样单元、自动稀释单元（备选）、蠕动泵单元、化学反应单元（含样品前处理装置）、检测器单元及数据处理单元。

由计算机软件控制自动完成每一个样品的全过程分析，包括系列标准溶液的配制、取样、前处理、化学... 厂家：上海政泓市场价格：优惠价格：百度搜索联系IL500总氮自动分析仪标题：IL500总氮自动分析仪传统的总氮消解法不仅耗时，而且操作过程繁琐，很难满足大批量样品的分析测试需要。

SGM2013-1.8中文资料

300mA,Low Power,Low Dropout, SGM2013 3-Terminal,Linear RegulatorsSG Microelectronics Co, LtdREV. C Tel: 86/451/84348461ORDERING INFORMATIONMODELV OUT (V)PIN- PACKAGESPECIFIED TEMPERATURERANGE ORDERING NUMBERPACKAGE MARKINGPACKAGE OPTIONSOT23-3 SGM2013-1.8XN3/TRXD18 Tape and Reel, 3000SOT89-3SGM2013-1.8XK3/TR SGM2013-1.8XK3Tape and Reel, 1000SGM2013-1.8 1.8VSOT89-3(L-Type)- 40°C to +125°CSGM2013-1.8XK3L/TRSGM2013-1.8XK3L Tape and Reel, 1000SOT23-3 SGM2013-2.5XN3/TR XD25 Tape and Reel, 3000SOT89-3SGM2013-2.5XK3/TR SGM2013-2.5XK3Tape and Reel, 1000SGM2013-2.5 2.5VSOT89-3(L-Type)- 40°C to +125°CSGM2013-2.5XK3L/TRSGM2013-2.5XK3L Tape and Reel, 1000SOT23-3 SGM2013-2. 7XN3/TR XD27 Tape and Reel, 3000SOT89-3SGM2013-2. 7XK3/TRSGM2013-2. 7XK3 Tape and Reel, 1000SGM2013-2.7 2. 7VSOT89-3(L-Type)- 40°C to +125°CSGM2013-2. 7XK3L/TR SGM2013-2. 7XK3L Tape and Reel, 1000SOT23-3 SGM2013-2.8XN3/TR XD28 Tape and Reel, 3000SOT89-3SGM2013-2.8XK3/TR SGM2013-2.8XK3Tape and Reel, 1000SGM2013-2.8 2.8VSOT89-3(L-Type)- 40°C to +125°CSGM2013-2.8XK3L/TRSGM2013-2.8XK3L Tape and Reel, 1000SOT23-3 SGM2013-2.9XN3/TR XD29 Tape and Reel, 3000SOT89-3SGM2013-2.9XK3/TR SGM2013-2.9XK3Tape and Reel, 1000SGM2013-2.9 2.9VSOT89-3(L-Type)- 40°C to +125°CSGM2013-2.9XK3L/TRSGM2013-2.9XK3L Tape and Reel, 1000SOT23-3 SGM2013-3.0XN3/TR XD30 Tape and Reel, 3000SOT89-3SGM2013-3.0XK3/TR SGM2013-3.0XK3Tape and Reel, 1000SGM2013-3.0 3.0VSOT89-3(L-Type)- 40°C to +125°CSGM2013-3.0XK3L/TRSGM2013-3.0XK3L Tape and Reel, 1000SOT23-3 SGM2013-3.3XN3/TR XD33 Tape and Reel, 3000SOT89-3SGM2013-3.3XK3/TR SGM2013-3.3XK3Tape and Reel, 1000SGM2013-3.3 3.3VSOT89-3(L-Type)- 40°C to +125°CSGM2013-3.3XK3L/TRSGM2013-3.3XK3L Tape and Reel, 1000ABSOLUTE MAXIMUM RATINGSIN to GND.....................................................................- 0.3V to +6VOutput Short-Circuit Duration............................................Infinite OUT to GND...................................................- 0.3V to (V IN + 0.3V) Power Dissipation, P D @ T A = 25℃SOT23-3 .....................................................................................0.4W SOT89-3 ................................................................................0.571W Package Thermal ResistanceSOT23-3, θJA ....................................................................... 250/W ℃SOT89-3, θJA .........................................................................175°C/W Operating Temperature Range................. ..........- 40°C to +125°C Junction Temperature...........................................................+150°C Storage Temperature.............................................- 65°C to +150°C Lead Temperature (soldering, 10s).......................................260°C ESD SusceptibilityHBM..........................................................................................4000V MM. (400V)Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.PIN DESCRIPTIONNAME FUNCTIONINRegulator Input. Supply voltage can range from 2.5V to 5.5V. GND Ground.OUT Regulator Output.ELECTRICAL CHARACTERISTICS(V IN= V OUT(NOMINAL)+ 0.5V (1), T A= - 40°C to +125°C, unless otherwise noted. Typical values are at T A= + 25°C.)PARAMETER SYMBOL CONDITIONS MINTYPMAXUNITSInput Voltage V IN 2.55.5VOutput Voltage Accuracy(1)I OUT =1mA to 300mA, T A = +25°CV OUT + 0.5V≤V IN≤ 5.5V-3 +3 %Maximum Output Current 300 mA Current Limit I LIM310 750 mANo load, 77 145Ground Pin Current I QI OUT = 300mA, 200µAI OUT = 1mA 0.8Dropout Voltage (2)I OUT = 300mA 300 380mVLine Regulation(1)ΔV LNR V IN = 2.5V or (V OUT +0.5V) to 5.5V,I OUT = 1mA0.03 0.15 %/VLoad Regulation ΔV LDR I OUT = 0.1mA to 300mA, C OUT = 1µF 0.0008 0.002 %/mAf = 100Hz, 75 dB Power Supply Rejection Rate PSRR I LOAD = 50mA, C OUT = 1µFf = 1KHz, 53 dB THERMAL PROTECTIONThermal Shutdown Temperature T SHDN160 ℃Thermal Shutdown Hysteresis ΔT SHDN15 ℃Specifications subject to change without notice.Note 1:V IN = V OUT(NOMINAL) + 0.5V or 2.5V, whichever is greater.Note 2: The dropout voltage is defined as V IN - V OUT, when V OUT is 100mV below the value of V OUT for V IN = V OUT + 0.5V. (Only applicable forV OUT = +2.5V to +5.0V.)TYPICAL OPERATING CHARACTERISTICSV IN = V OUT (NOMINAL) + 0.5V or 2.5V (whichever is greater), C IN = 1µF, C OUT = 1µF, T A = +25℃, unless otherwise noted.TYPICAL OPERATING CHARACTERISTICSV IN = V OUT (NOMINAL) + 0.5V or 2.5V (whichever is greater), C IN = 1µF, C OUT = 1µF, T A = +25℃, unless otherwise noted.TYPICAL OPERATING CHARACTERISTICSV IN = V OUT (NOMINAL) + 0.5V or 2.5V (whichever is greater), C IN = 1µF, C OUT = 1µF, T A = +25℃, unless otherwise noted.Application NotesWhen LDO is used in handheld products, Attention must be paid to voltage spike which would damage SGM2013. In such applications, voltage spike will be generated at changer interface and V BUS pin of USB interface when changer adapters and USB equipments are hot-inserted. Besides this, handheld products will be tested on the production line on the condition of no battery. Test Engineer will apply power from the connector pin which connects with positive pole of the battery. When external power supply is turned on suddenly, the voltage spike will be generated at the battery connector. The voltage spike will be very high, it always exceeds the absolute maximum input voltage (6.0V) of LDO. In order to get robust design. Design Engineer needs to clear up this voltage spike. Zener diode is a cheap and effective solution to eliminate such voltage spike. For example, BZM55B5V6 is a 5.6V small package Zener diode which can be used to remove voltage spike in cell phone design. The schematic is shown in below:PACKAGE OUTLINE DIMENSIONS SOT23-3PACKAGE OUTLINE DIMENSIONS SOT89-3REVISION HISTORYLocation Page12/06— Data Sheet changed from REV. A to REV. BChanged to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Added Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 03/07— Data Sheet changed from REV. B to REV. CChanged to TYPICAL OPERATING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Shengbang Microelectronics Co, LtdUnit 3, ChuangYe PlazaNo.5, TaiHu Northern Street, YingBin Road Centralized Industrial ParkHarbin Development Zone150078HeiLongJiangHarbin,ChinaP.R.Tel.: 86-451-84348461Fax: 86-451-84308461。

帕顿378s型号扫描开关使用手册说明书

USER MANUAL
MODEL 378S
Serial Scanning Switch
Part# 07M378S-B Doc# 020011UB Revised 4/20/93
SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007
• Available with up to 1 Meg of RAM buffer
• Individual port LEDs show scanning progress and which port is loading data
• Buffer status LEDs show amount of buffer currently being used
To configure the Model 378S, you must first open the case by taking off the 4 screws (2 on each side). Then locate the DIP switches (shown below) at the lower center of the PC board:
The Model 378S allows input/output data rates to 19.2Kbps, and supports both hardware (CTS/DSR) and software (X-ON/X-OFF) handshaking methods. Convenience features of the Model 378S include a manual "step" button that overrides automatic scanning, and a master buffer clear button. Two sets of LED indicators are provided: one set shows which port is currently being scanned or loaded, the other set shows the percentage of buffer space currently available.

霍尼韦尔MS3780 Fusion全向多线激光条码扫描器

霍尼韦尔MS3780 Fusion激光扫描器产品参数
环境参数工作温度：-20℃-40℃ 存储温度：-40℃-60℃ 湿度：5％-95％相对湿度，非凝结状态照度：4842 LUX（450尺烛光）抗震性：能承受1.5米的空中摔落防尘性：密封以抵挡空气尘粒侵入扫描参数分辨率：5 mil/7.5mil 扫描类型：全向多线：5个方向，每个方向4条扫描线；按钮触发单线模式扫描速度：全向多线:1300次/秒单线：67次/秒扫描角度：水平:50° 可识别的印刷对比度：最低35％的反射差转角，仰角，偏角：360°，60°，60° 解码能力：Code 39，Code 93，Code 128，UPC/EAN/JAN,Code 2 of 5， Code 11，Codabar，MSI Plessey，GS1 DataBar，Telepen，Trioptic
霍尼韦尔MS3780 Fusion激光扫描器产品参数
性能参数光源：可视激光二极管激光，波长650nm±10nm 蜂鸣器：7种声调或无声指示灯：蓝色=激光亮，准备扫描；白色=解码成功；黄色=自动扫描系统接口：USB，RS232串口，PC口，IBM46xx（RS458），OCIA 电学参数输入电压：5 VDC±0.25 V 工作功率：1.4W（275 mA@5 V）-典型值备用功率：1.0 mW（200 mA@5 V）-典型值直流电变压器：Class 2：5.2 VDC@1A 激光等级：Class 1：IEC60825-1，EN60825-1 电磁兼容性：FCC Part 15，ICES-003，EN55022 Class B
霍尼韦尔MS3780 Fusion激光扫描器特征及优点
1、全向多线扫描模式为主：可以在任意方向快速扫描条码，提高效率。 2、单线扫描模式为辅：按下扫描模式选择按钮可切换到单线模式进行精确的菜单扫描。

SGM6605 REV.A_20130107

SG Micro Corp
3
SGM6605
90% Efficient Synchronous Step-Up Converter with 1.1A Switch
ELECTRICAL CHARACTERISTICS
(Full = -40℃ to +85℃, typical values are at TA = +25℃, unless otherwise noted.)
GND
ቤተ መጻሕፍቲ ባይዱ
2
5
VOUT
EN
3
4
NC/FB
PIN DESCRIPTION
PIN 1 2 3 4 5 6 NAME SW GND EN NC FB VOUT VCC Boost and Rectifying Switch Input. Ground. Enable Input. (1/VCC enabled, 0/GND disabled) No Connect. It should be left floating. (SGM6605-5.0) Output Voltage Feedback Pin. Voltage feedback for programming the output voltage. (SGM6605-ADJ) Boost Converter Output. Boost Converter Supply Voltage. FUNCTION
APPLICATIONS
Single-Cell Li Battery Powered Products Portable Audio Players Cellular Phones Personal Medical Products

California Instruments CSW Series 5550-33300 VA AC

InputVoltage Ranges Factory configured 187 to 264 Vrms, 3ø L-L (3 wire), or 342 to 457 Vrms, 3ø L-L (4 wire). A chassis ground is also required. Power Factor PFC Input, 0.99PFFrequency Range47 to 440 HzEfficiency70% min, at full loadRide Through10 ms minimumOutputPower5550 VA: 1ø or 3ø (systems up to 33,000 VA)AC or DC Output Voltage0 to156 Vrms L-N, low range; 0 to 312 Vrms L-N, high rangeCurrent Per Phase16A to 115V in 156V range; 8A to 230V in 312V range per, 1850 VA module.Power Factor of Load0 lagging to 0 leading (0-unity)Crest Factor 3.5:1 (peak output current to rms output current))Frequency Range Specifications apply DC, 40Hz to 5kHz. For output frequencies greater than 1 kHz, the max slew rateallowed is 1 kHz per second.Max Total Harmonic Distortion(Full Linear Load or No Load): 0.25% max, 40 to 100 Hz; 0.5% max to 500 Hz; and 1% max to 1 kHz plus 1%/kHz to 5 kHzAC Noise Level>60 dB rms below full output voltageAmplitude Stability With Remote Sense±0.1% of full scale over 24 hours at constant line, load and temperatureLine Regulation(DC, or 40 Hz to 5 kHz): ±0.015% of full scale for a ±10% input line changeLoad Regulation±0.025% of full scale voltage for a full resistive load to no load; above 1 kHz, add ±0%/kHzVoltage Accuracy±0.1% of range. Above 1 kHz, add 0.2%/kHz. Add ±0.1% of full scale for “AC PLUS DC” mode. Valid for 5 to 156 Vrms and10 to 312 Vrms at 25°CVoltage Resolution1mV (0.1V) Full ScaleFrequency Accuracy±0.01% at 25°C ±0.001%/°CFrequency Resolution40 Hz to 81.91 Hz (0.01 Hz)81.90 Hz to 819 Hz (0.01 Hz)820 Hz to 5000 Hz (1 Hz)Phase Accuracy, Phase-to-PhaseBalanced Linear Resistive Load±1% of Programmed valuePhase Angle Resolution0.1°Remote Output Voltage Sense 5 Vrms total lead drop, maxCSW Series : Product SpecificationsCommon Intput and OutputsRemote Inhibit A logic Low or High contact closure input to inhibit the outputsExternal Amplitude Modulation0 to 5 VRMS provides 0 to 20% output amplitude modulation (±2% of full scale output).External Drive Input Acts as Amplifier, 0 to 5 VRMS (DC to 5 kHz) or ±5 VDC input for zero to full scale programmed voltage output(±2% of full scale output). Individual inputs for an external signal for each of the three phases.Remote Programming Voltage0 to ±7.07 VDC provides zero to full scale programmed voltage output(±2% of full scale output).External Input Impedance40K (ohm symbol) for each of the three inputs.Externaly Sync External Sync allows the output frequency of the AC source to be synchronized to an external TTL level clock signal.LKM Clock and Lock Master. Enables synchronizing outputs of two or more California Instruments sources, one acts as master.LKS Clock and Lock AuxiliaryFront Panel Trigger, BNC Connector Output available at the front panel BNC connector that provides a negative going pulse for any programmed voltage or frequencychange. The trigger can be reassigned as an output when running list transients.Front Panel Phase A, B and C, BNC connectors These three outputs are representive of the programmed output waveform, magnitude and frequency. 0 to 4.86 Vrms represents 0 to a full-scale output voltage.206858.458.0223sales.ppd@CSW Series : Product SpecificationsEnvironmentalOperating Temperature 0°C to 45°C (32°F to 113°F)Storage Temperature -40°C to 70°C (-40°F to 158°F)CoolingAir is drawn in from the top, bottom, and sides and exhausted through the rear Humidity (Non-condensing)0 to 85% at 25°C (77°F); derate to 50% at 40°C (104°F)AltitudeOperating 10,000 ft, non operating 40,000 ftPhysicalDimensionsWidth: 19” (483 mm)Height: 8.75” (222 mm)Depth: 23.5” (597 mm)WeightCSW 5550 - 127 lbs (57.5 kg)Shipping Weight - US CSW - 160 lbs (72 kg)NoteMulti Chassis systems, dimension and weight are approximately x2, x3, x4, x5 and x6 CSW Specifications5550–33300 VAMeasurementsMeasurements - Standard (AC Measurements)Parameter Frequency Phase Voltage (AC)Current (AC rms)Real Power Apparent Power Power Factor Range40-81.91 Hz 82.0-819.1 Hz > 819 Hz 40-100 Hz 100-1000 Hz0-300 V0-50 A0-6 kW0-6 kVA0.00-1.00Accuracy* (±)1 ø mode (-1) 0.1% + 1 digit 0.5°0.5% + 250 mV 0.1% + 150 mA0.15% + 9 W0.15% + 9 VA 0.033 ø mode (-3)2°0.1% + 50 mA0.15% + 3 W 0.15% + 3 VA 0.01Resolution*.01 Hz / 0.1 Hz / 1 Hz0.1° / 1°10 mV 1 mA 1 W 1 VA 0.01* Accuracy specifications are in % of reading and apply above 100 counts. For multi-chassis configurations, current, power range and accuracy specifications are times three. Power factor accuracy applies for PF > 0.5 and VA > 50% of max. Frequency measurement specification valid for output > 30 Vrms.Constant Power AC ModeRMS VoltageR M S C u r r e n t5550 CSW Operating Areaper PhaseLow Range High Range16.0A11.8A8.0A 5.9A115V 156V 230V 312VHarmonic MeasurementsParameterRange Accuracy ( ± )Resolution Frequency fundamental 16.00 - 1000 Hz 2 counts 0.01 Hz to 1 Hz Frequency harmonics 32.00 Hz - 16 kHz 2º typ.0.5ºVoltage Fundamental 0.25V0.01V Harmonic 2 - 500.25V + 0.1% + 0.1%/kHz 0.01V CurrentFundamental 0.05A0.01A Harmonic 2 - 500.05A + 0.1% + 0.1%/kHz0.01AHarmonics frequency range in three-phase mode is 32 Hz - 16 kHz. Accuracy specifications are multiplied by the number of power sources in multi-source systems with the 3-phase (3Ø) or the number of sources times 3 in the 1-phase (1Ø) mode . Measurement bandwidth is limited to 16 Khz.ModelCSW5550CSW11100CSW16650CSW22200CSW17750CSW33300Multiplier 3Ø/1 Ø1/32/63/94/125/156/18CSW Series : Product SpecificationsProtection And SafetyOvervoltage Shutdown Programmable for 15V to 255V peak, 156V range; 30V to 510V peak, 312V range Programmable Current Limit Shutdown Settable to 0.01 ARMS ResolutionSettable to 1% of range: the timeout is settable from 100 ms to 10s.Programmable Current Limitwith Timed ShutdownOver temperature Shutdown Automatic, not programmableRegulatory Compliance• EN 61010• EN 55011• UL 3111• EN 50082-2• EN 61000-4-3, EN 61000-4-4• FCC Part 15, Class A• CE MarkDesigned to meet:• EN 61010• EN 55011• UL 3111• EN 50082-2• EN 61000-4-3, EN 61000-4-4• FCC Part 15, Class A208858.458.0223sales.ppd@CSW Series : Product Diagram8.620”Front View16.90”Rear View16.90”21.069”2.371”Top View 23.440”8-32UNC-2B A =ACCURIDE SLIDE MOUNTINGAAA4.10013.2504.8755.3301.8108.620Side View2.6801.065 DIA FOR INPUT WIRING .875 DIA FOR SENSE WIRING 1.063 DIA FOR OUTPUT WIRING6.32519” (483mm)8.71”(221 mm)5550–33300 VA210CSW Series© 2011 AMETEK Programmable Power All rights reserved. AMETEK Programmable Power is the trademark of AMETEK Inc., registered in the U.S. and other countries. Elgar, Sorensen, California Instruments, and Power Ten are trademarks of AMETEK Inc., registered in the U.S.Model Number DescriptionCSW5550208Power LevelInput PowerXXXOptionsXXX Input Options -400342-457 Volt Line to Line AC input.Output Options -LFLimits output frequency to 500 Hz.Cabinet Options -RMS Rackmount Slides. Recommended for rack mount applications.C prefixCabinet System. Installed and pre-wired in 19” cabinet.OptionsOptions Code Description-160RTCA/DO-160D, Change 2, EuroCAE-14D and Airbus test firmware.-704F Mil. Std. 704A-F tests -ABD Airbus Directive 0100.1.8 tests.-AMD Airbus AMD24 tests.-A350Airbus A350 tests.-B787Boeing 787B3-0147 tests.-AIRB Airbus ABD0100.1.8, AMD 24 and A350 combination test software suite -LAN LXI Ethernet LAN Interface (Rj45 Connector)-LKM Clock/Lock Master -LKS Clock/Lock Auxiliary-413IEC61000-4-13 Harmonics and Interharmonics test firmware and hardware.-411IEC61000-4-11 test firmware. See also EOS1/3.-WHM Watt-Hour Measurement option.-MB Multi-Box. Adds controller to auxiliary chassis of multi-chassis systems-SWSCPI Command Firmware (Simulates the Elgar SW Series) Not all commands are supported. Please contact factory for details.。

刹车片国内型号FMIS代码表格2013

2012-2013 菲亚特500 掀背/两箱/500C
派朗
2008- 博锐 1.4
2004-2007 E87/E81 116i/118i/120i
2007- E87/E81 120i/130i
1989-1998 E36 所有车款
1998-2005 E46 所有车款
2005-2007 E90 318i 320i
2006- 速腾 1.8T (Sagitar)
2005- 新甲壳虫
(Beetle) 进口车
一汽大众 2006-
迈腾 1.6 迈腾 2.0
(Magotan)
2004- 辉腾 3.0/4.2 (Phaeton) 进口车
2002- 辉腾 6.0 (Phaeton) 进口车
一汽大众
2002-2006 途锐 02款
2008- 奥迪 A5 1.8T 2.0TDI 3.0T 3.2FSI
1994-1997 奥迪 A6 老款 C4 旧款6缸
1997-1998 奥迪 A6 2.7(8片）
2005- 奥迪 A6 2.7T/3.7/4.2quattro
1997-2005 奥迪 A6 C5 1.8L/1.8T/2.4/2.8
2008- CC 1.8T 2.0T
2008- CC 3.6
2009-2012 CC VR6
2013- CC VR6 新款
2009
CC
2010-2012 CC
奥迪 80
1990-1994 奥迪 100
2003- 奥迪 A3
2001-2008 奥迪 A4
2008- 奥迪 A4L
2008- 奥迪 A4L 2.0T 3.0
1995-2002 W210 E200/220/230/250

深圳市信华翰科技有限公司扫描枪产品说明书

公司简介深圳市信华翰科技有限公司成立于2006年，注册资金500万，办公室位于深圳市商业中心，华强北商圈的国际科技大厦11楼，办公面积320平方。

是Honeywell 金牌代理商、Newland 新大陆金牌代理商、摩托罗拉讯宝SYMBOL 战略合作伙伴、优尼泰克授权服务商。

我司共代理有十几个品牌的条码设备，为客户提供优质丰富的条码相关产品和系统集成专业服务。

扫描网是深圳市信华翰科技有限公司斥资100万打造的扫描枪的网上商城。

信华翰为了让中国的条码事业走得更好更快，让大众都能享受条码带来的便利，特此为全国商户带“”来质优价廉的各类扫描枪，扫描网所售的所有扫描枪均是厂家授权，均经过三测（出厂检测，到货检测，出货检测）的优良产品。

PIRY ins zebexOPTICONT S C合作伙伴Honeywell深圳市信华翰科技有限公司SHENZHEN XIN HUA HAN SCIENCE AND TECHNOLOGY CO.,LTD.地址:深圳市福田区深南中路3007号国际科技大厦11楼电话****************************;传真**************展销部:深圳市华强北赛格大厦7106室网址：服务热线：新大陆HR1030手持式扫描枪北京意锐RC532二维码扫描平台摩托罗拉C11一维扫描枪霍尼韦尔1900GHD二维码扫描枪PIRYinsHoneywell如何正确使用条码阅读器：1、在条码阅读器和条码保持一定的倾角，以达到最佳效果。

2、在条码阅读器和条码间的角度不能为90度，否则不能正常读码。

3、务必让条码被完整扫描，确定阅读器能正确扫读。

介绍说明：该条码扫读设备为计算机信息系统提供精确，易用和快速的数据录入和存入的完备的解决方案。

本产品提供完整的接口方式以适应各类主机的计算机系统包括：KeyboardWandRS-232Dual RS-232USBOTHERS所有译码器的参数设定都可通条码的扫描来完成，并保存在存储记忆体中，在关闭电源后仍保留设置。

SGM810

SGM803/SGM809/SGM810 Microprocessor SupervisoryCircuit in 3-Pin SOT-23GENERAL DESCRIPTIONThe SGM803/SGM809/SGM810 supervisory circuitsmonitor the power supply voltage in microprocessor anddigital systems. They provide a reset output duringpower-up, power-down and brownout conditions. Onpower-up, an internal timer holds reset asserted for240ms. This holds the microprocessor in a reset stateuntil conditions have stabilized. The RESET outputremains operational with V CC as low as 1V. The SGM803/SGM809 provides an active low reset signal (RESET)while the SGM810 provides an active high signal(RESET) output. The SGM809/SGM810 has push-pulloutputs, whereas the SGM803 has an open-drain output,which requires an external pull-up resistor.Eight reset threshold voltage options are availablesuitable for monitoring 1.8V, 2.5V, 3V, 3.3V and 5Vsupply voltages.The reset comparator features built-in glitch immunity,making it immune to fast transients on V CC.The low supply current of typically 13μA makes theSGM803/SGM809/SGM810 ideal for use in portable,battery operated equipment. All are specified over theextended -40℃ to +125℃ temperature range.TYPICAL OPERATION CIRCUITFEATURES●Precision Voltage Monitor: 1.8V, 2.5V, 3V, 3.3V, 5VOptions●Superior Upgrade for MAX803/MAX809/MAX810and ADM803/ADM809/ADM810●Fully Specified over Temperature●Low Power Consumption (13μA TYP)●Reset Assertion Down to 1V V CC●150ms Min Power-On ResetOpen-Drain RESET Output (SGM803)Push-Pull RESET Output (SGM809)Push-Pull RESET Output (SGM810)●-40℃ to +125℃ Operating Temperature Range●Small PackagingSGM803 Available in SOT-23-3 and SOT-23SGM809 Available in SOT-23-3 and SOT-23SGM810 Available in SOT-23-3 and SOT-23APPLICATIONSMicroprocessor SystemsControllersIntelligent InstrumentsAutomotive SystemsSafety SystemsPortable InstrumentsPIN CONFIGURATIONS (TOP VIEW)12SOT-23-3 / SOT-23GNDV CC3RESET/RESETSGM803SGM809SGM810REV.E. 1 SG Micro CorpCircuit in 3-Pin SOT-232SGM803/SGM809/SGM810SG Micro CorpPACKAGE/ORDERING INFORMATIONMODELRESETTHRESHOLD (V)PACKAGE DESCRIPTION ORDERING NUMBERPACKAGE MARKING PACKAGE OPTION 4.63 SOT-23-3 SGM803-LXN3/TR 803L Tape and Reel, 30004.63SOT-23SGM803-LXN3L/TR803LLTape and Reel, 30004.38 SOT-23-3 SGM803-MXN3/TR 803M Tape and Reel, 30004.38 SOT-23 SGM803-MXN3L/TR 803ML Tape and Reel, 30004.00 SOT-23-3 SGM803-JXN3/TR 803J Tape and Reel, 30004.00 SOT-23 SGM803-JXN3L/TR 803JL Tape and Reel, 30003.08 SOT-23-3 SGM803-TXN3/TR 803TTape and Reel, 30003.08 SOT-23 SGM803-TXN3L/TR 803TL Tape and Reel, 30002.93 SOT-23-3 SGM803-SXN3/TR 803S Tape and Reel, 30002.93 SOT-23 SGM803-SXN3L/TR 803SL Tape and Reel, 30002.63 SOT-23-3 SGM803-RXN3/TR 803R Tape and Reel, 30002.63 SOT-23 SGM803-RXN3L/TR 803RL Tape and Reel, 30002.32 SOT-23-3 SGM803-ZXN3/TR 803Z Tape and Reel, 30002.32SOT-23SGM803-ZXN3L/TR803ZLTape and Reel, 30001.63 SOT-23-3 SGM803-XXN3/TR 803X Tape and Reel, 3000SGM8031.63 SOT-23 SGM803-XXN3L/TR 803XL Tape and Reel, 30004.63 SOT-23-3 SGM809-LXN3/TR 809L Tape and Reel, 30004.63SOT-23SGM809-LXN3L/TR809LLTape and Reel, 30004.38 SOT-23-3 SGM809-MXN3/TR 809M Tape and Reel, 30004.38 SOT-23 SGM809-MXN3L/TR 809ML Tape and Reel, 30004.00 SOT-23-3 SGM809-JXN3/TR 809J Tape and Reel, 30004.00 SOT-23 SGM809-JXN3L/TR 809JL Tape and Reel, 30003.08 SOT-23-3 SGM809-TXN3/TR 809TTape and Reel, 30003.08 SOT-23 SGM809-TXN3L/TR 809TL Tape and Reel, 30002.93 SOT-23-3 SGM809-SXN3/TR 809S Tape and Reel, 30002.93 SOT-23 SGM809-SXN3L/TR 809SL Tape and Reel, 30002.63 SOT-23-3 SGM809-RXN3/TR 809R Tape and Reel, 30002.63 SOT-23 SGM809-RXN3L/TR 809RL Tape and Reel, 30002.32 SOT-23-3 SGM809-ZXN3/TR 809Z Tape and Reel, 30002.32 SOT-23 SGM809-ZXN3L/TR 809ZL Tape and Reel, 30001.63 SOT-23-3 SGM809-XXN3/TR 809X Tape and Reel, 3000SGM8091.63 SOT-23 SGM809-XXN3L/TR 809XLTape and Reel, 3000Circuit in 3-Pin SOT-233SGM803/SGM809/SGM810SG Micro CorpPACKAGE/ORDERING INFORMATION (Cont.)MODELRESETTHRESHOLD (V)PACKAGE DESCRIPTION ORDERING NUMBERPACKAGE MARKING PACKAGE OPTION 4.63 SOT-23-3 SGM810-LXN3/TR 810L Tape and Reel, 30004.63 SOT-23 SGM810-LXN3L/TR 810LL Tape and Reel, 30004.38 SOT-23-3 SGM810-MXN3/TR 810M Tape and Reel, 30004.38 SOT-23 SGM810-MXN3L/TR 810ML Tape and Reel, 30004.00 SOT-23-3 SGM810-JXN3/TR 810J Tape and Reel, 30004.00 SOT-23 SGM810-JXN3L/TR 810JL Tape and Reel, 30003.08 SOT-23-3 SGM810-TXN3/TR 810TTape and Reel, 30003.08 SOT-23 SGM810-TXN3L/TR 810TL Tape and Reel, 30002.93 SOT-23-3 SGM810-SXN3/TR 810S Tape and Reel, 30002.93 SOT-23 SGM810-SXN3L/TR 810SL Tape and Reel, 30002.63 SOT-23-3 SGM810-RXN3/TR 810R Tape and Reel, 30002.63 SOT-23 SGM810-RXN3L/TR 810RL Tape and Reel, 30002.32 SOT-23-3 SGM810-ZXN3/TR 810ZTape and Reel, 30002.32 SOT-23 SGM810-ZXN3L/TR 810ZL Tape and Reel, 30001.63 SOT-23-3 SGM810-XXN3/TR 810X Tape and Reel, 3000SGM8101.63SOT-23SGM810-XXN3L/TR810XLTape and Reel, 3000Circuit in 3-Pin SOT-234SGM803/SGM809/SGM810SG Micro CorpABSOLUTE MAXIMUM RATINGS(Typical values are at T A = 25°C, unless otherwise noted.)V CC ............................................................................-0.3V to 6V RESET , RESET ............................................-0.3V to V CC + 0.3V Input Current, V CC .............................................................20mA Output Current, RESET ,RESET ……………………………..20mA Rate of Rise, V CC ...........................................................100V/μs Power Dissipation, P D @ T A = 25℃SOT-23-3 ............................................................................0.4WPackage Thermal ResistanceSOT-23-3, θJA ............................................................... 250℃/W Operating Temperature Range..........................-40°C to +125°C Junction Temperature........................................................150°C Storage Temperature........................................-65°C to +150°C Lead Temperature (Soldering, 10s)...................................260°C ESD SusceptibilityHBM..................................................................................4000V MM.. (400V)NOTE:Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.CAUTIONThis integrated circuit can be damaged by ESD if you don’t pay attention to ESD protection. SGMICRO recommends that all this integrated circuit can be damaged by ESD if you don’t pay attention to ESD protection. SGMICRO recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. SGMICRO reserves the right to make any change in circuit design, specification or other related things if necessary without notice at any time. Please contact SGMICRO sales office to get the last datasheet.PIN DESCRIPTIONCircuit in 3-Pin SOT-235SGM803/SGM809/SGM810SG Micro CorpELECTRICAL CHARACTERISTICS(V CC TYP = 5V for L/M/J Models, 3.3V for T/S Models, 3V for R Models, 2.5V for Z Models, 1.8V for X Models; unless otherwise noted.)Circuit in 3-Pin SOT-236SGM803/SGM809/SGM810SG Micro CorpTYPICAL PERFORMANCE CHARACTERISTICSCircuit in 3-Pin SOT-237SGM803/SGM809/SGM810SG Micro CorpTYPICAL PERFORMANCE CHARACTERISTICSCircuit in 3-Pin SOT-238SGM803/SGM809/SGM810SG Micro CorpAPPLICATION NOTESBENEFITS OF AN ACCURATE RESET THRESHOLDIn other microprocessor supervisory circuits, tolerances in supply voltages lead to an overall increase in reset tolerance levels due to the deterioration of the microprocessor reset circuit’s power supply. The possibility of a malfunction during a power failure is greatly reduced because the SGM803/ SGM809/SGM810 series can operate effectively even when there are large degradations of the supply voltages. Another advantage of the SGM803/SGM809/SGM810 series is its very accurate internal voltage reference circuit. These benefits combine to produce an exceptionally reliable voltage monitor circuit.INTERFACING TO MICROPROCESSORS WITH MULTIPLE INTERRUPTSIn a number of cases, it is necessary to interface many interrupts from different devices (for example, thermal, altitude, and velocity sensors). The SGM803/SGM809/SGM810 can easily be integrated into existing interrupt-handling circuits, as shown in Figure 1, or can be used as a standalone device.Figure 1. Interfacing to Microprocessors with MultipleInterruptsINTERFACING TO OTHER DEVICES’ OUTPUTThe SGM803/SGM809/SGM810 series is designed to integrate with as many devices as possible and, therefore, has a standard output dependent on V CC . This enables the parts to be used in both 3V and 5V, or any nominal voltage within the minimum and maximum specifications for V CC . This design simplifies interfacing this device to other devices.ENSURING A VALID RESET OUTPUT DOWN TO V CC = 0VWhen V CC falls below 1.0V, the SGM803/SGM809 RESET no longer sinks current. A high impedance CMOS logic input connected to RESET may, therefore, drift to undetermined logic levels. To eliminate this problem, a 100k Ωresistor should be connected from RESET to ground.Figure 2. Ensuring a Valid Reset Output Down to V CC = 0VPREVENTING THE HIGH VOLTAGE SPIKE AND LOW POWER DESIGNTo prevent the high voltage spike damage or input V CC current limitation low power design, It is always to connect a resistor R1(0Ω to 1k Ω) in series to V CC , for such application, one capacitance C1(0.1µF to 4.7µF) should be connected between V CC Pin and GND. the schematic is shown in Figure 3. The input resistor will affect output driving capability.OUTPUTINFigure 3. Preventing the High Voltage Spike and Low Power Design .Circuit in 3-Pin SOT-239SGM803/SGM809/SGM810SG Micro CorpDETAILED DESCRIPTIONSRESET TIMINGThe reset signal is asserted LOW for the SGM809 and HIGH for the SGM810 when the power supply voltage falls below the threshold trip voltage and remains asserted for at least 150ms after the power supply voltage has risen above the threshold.Power Supply Voltage5V0V 5V0V 5V 0VRESETRESETFigure 4. Reset Timing DiagramCircuit in 3-Pin SOT-2310SGM803/SGM809/SGM810SG Micro CorpPACKAGE OUTLINE DIMENSIONSSOT-23-3RECOMMENDED LAND PATTERN (Unit: mm)Dimensions In Millimeters Dimensions In InchesSymbol MIN MAX MIN MAX A 1.050 1.250 0.041 0.049 A1 0.000 0.100 0.000 0.004 A2 1.050 1.150 0.041 0.045 b 0.300 0.500 0.012 0.020 c 0.100 0.200 0.004 0.008 D 2.820 3.020 0.111 0.119 E 1.500 1.700 0.059 0.067 E12.650 2.950 0.104 0.116e 0.950 BSC 0.037 BSC e1 1.900 BSC 0.075 BSC L 0.300 0.600 0.012 0.024 θ0° 8° 0° 8°Circuit in 3-Pin SOT-2311SGM803/SGM809/SGM810SG Micro CorpPACKAGE OUTLINE DIMENSIONSSOT-23RECOMMENDED LAND PATTERN (Unit: mm)Dimensions In Millimeters Dimensions In Inches SymbolMIN MAX MIN MAXA 0.900 1.150 0.035 0.045 A1 0.000 0.100 0.000 0.004 A2 0.900 1.050 0.035 0.041 b 0.300 0.500 0.012 0.020 c 0.080 0.150 0.003 0.006 D 2.800 3.000 0.110 0.118 E 1.200 1.400 0.047 0.055 E1 2.250 2.550 0.089 0.100 e 0.950 BSC 0.037 BSC e1 1.900 BSC 0.075 BSC L 0.550 REF 0.022 REF L1 0.300 0.500 0.012 0.020 θ 0° 8° 0° 8°Circuit in 3-Pin SOT-2312SGM803/SGM809/SGM810SG Micro CorpTAPE AND REEL INFORMATIONNOTE: The picture is only for reference. Please make the object as the standard.KEY PARAMETER LIST OF TAPE AND REELPackage TypeReel DiameterReel WidthW1 (mm)A0 (mm)B0 (mm)K0 (mm)P0 (mm)P1 (mm)P2 (mm)W (mm)Pin1 QuadrantSOT-23-3 7″ 9.03.2 3.3 1.34.0 4.0 2.0 8.0Q3 SOT-23 7″9.5 3.152.771.224.0 4.0 2.0 8.0Q3REEL DIMENSIONSCircuit in 3-Pin SOT-2313SGM803/SGM809/SGM810SG Micro CorpCARTON BOX DIMENSIONSNOTE: The picture is only for reference. Please make the object as the standard.KEY PARAMETER LIST OF CARTON BOXReel Type Length (mm) Width (mm) Height (mm) Pizza/Carton7″ (Option)36822722487″ 442 410 224 18。

MP3336A-C-00A双通道高功率闪光LED驱动器说明书

EV3336A-C-00ADual-Channel Flash LED DriverWith 2A/Ch and I2C InterfaceDESCRIPTIONThe MP3336A is a compact, dual-channel, high-power, flash LED driver that can drive up to 2A in flash mode for each LED. It is usually applied for camera phones to improve image and video quality in low-light environments. The MP3336A operates with a selectable 1/2/3/4MHz switching frequency and uses a synchronous, current-mode PWM boost converter to regulate the LED current with two high-current sources. The MP3336A provides a high efficiency and optimized solutionfor smaller PCB spaces.The MP3336A features a standard I2C interface, dual LED channels, rich protection modes, and high power density and performances. The MP3336A can also support flash, assist, indicator, and 5V DC modes.The cathodes of the dual-flash LED are referenced to GND, which is better for improving thermal performance in layout. The MP3336A is available in a WLCSP-20 (1.6mmx2.0mm) package.ELECTRICAL SPECIFICATION Parameter SymbolValueUnits Input Voltage V IN 2.7-5.5 V Output Voltage V OUT <5.5 VLEDs # 2LED Current/string I LED Max.2 A FEATURES∙ 2.7V~5.5V Input Voltage∙1/2/3/4MHz Selectable Max Fsw∙Fsw Fold-back Function∙ 400kHz I2C Compatible Interface∙ Standby/Flash/Assist/Indicator/5V DC ModesFlash Mode∙Up to 2A/Ch Programmable Current with ±7% Accuracy for Each LED, 7.84mA/Step Assist Mode∙Up to 319mA/Ch Programmable Current with ±7% Accuracy for Each LED,1.25mA/StepIndicator Mode∙Works in 31.5kHz PWM Dimming Mode with 2/16, 3/16, 4/16, 5/16 Duty Cycle∙Used for Blinking and 128/256/512ms Selectable Blinking Time5V DC Mode∙Output Constant 5V DC Voltage∙Separated EN1 Pin for NFC Application∙1A to 4.2A Programmable Input DC Current Limit Protection∙External Strobe/TX Pin∙VIN to VOUT Disconnection Function∙Low-Battery Voltage Protection∙LED Short/Open Protection∙VOUT-GND Short Protection∙Over-Voltage Protection (OVP)∙Over-Temperature Protection (OTP)∙Input Under-Voltage Lockout (UVLO) Protection∙ WLCSP-20 (1.6mmx2.0mm) Package APPLICATIONS∙Smartphone Flash LED Application∙Cameras for Tablets∙ Digital Still CameraAll MPS parts are lead-free, halogen free, and adhere to the RoHS directive. For MPS green status, please visit MPS website under Quality Assurance. “MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc.EV3336A-C-00A EVALUATION BOARD(L × W) 5.5cm x 5.5cmBoard Number MPS IC NumberEV3336A-C-00A MP3336AGCEVALUATION BOARD SCHEMATICFigure 1: Dual-Channel Application CircuitEV3336A-C-00A BILL OF MATERIALSQty Ref Value Description Package Manufacturer Manufacturer PN 1 C1 NC 06032 C2,C4 10uFCeramicCapacitor,10V,X5R0805 muRata GRM21BR61A106KE19L 1 C3 NC 0805 3 R1,R6,R7 0 res,1% 0603 Yageo RC0603FR-070RL 4 R2,R3,R4,R5 NC 0603 1 L1 1.1uH 1.1uA, 20m, 3.46A TDK D53LC-#A915AY-1R1M1 U1 MP3336A CSP92.01*1.61mmMPS MP3336APRINTED CIRCUIT BOARD LAYQUICK START GUIDE1. Connect the positive and negative terminals of the power supply (2.7V ~5.5V) to the VIN and GNDpins on the EV board, respectively.2. Supply the EN terminal with logical signal.3. Connect the positive and negative terminals of the LED to the LED1/2 pin and GND on the EVboard, respectively.4. Please connect SCL, SDA and GND of EV board to the SCL, SDA and GND of a programmable kit(EVKT-USBI2C-02) with I2C interface, respectively.5. Power on sequence: VIN →EN →I2C setting → Set LED1/2_EN bit (to light the LED load). Whenwork in flash mode with hardware trigger mode, please give a level or pulse signal to STR pin. NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications.。

banner-sc10-2roe-安全继电器控制器-10个输入（4个可转换），两个3通道安全继电器输

DatasheetFor complete technical information about this product, including installation instructions, application requirements and guidelines,EU Declaration of Conformity, technical specifications, and accessories, see and search 174868.•Intuitive, icon-based programming with drag-and-drop PC configuration simplifies device setup and management •Two six-amp safety relay outputs, each with three N.O. sets of contacts •Ten inputs, including four that can be used as non-safe outputs•Automatic Terminal Optimization (ATO) can increase the inputs from 10 to up to 14•Industrial Ethernet two-way communication◦256 virtual non-safe status outputs◦80 virtual non-safe inputs (reset, on/off, cancel off-delay, mute enable)•SC-XM3 external drive for fast swap and quick configuration without a PCNote: Configuration software is required.The software is available at /safetycontroller .SC10-2 Features and IndicatorsConnection points are push-in spring clamp connectors.Micro USB & LED4 Safe Inputs & LEDsor4 Non-Safe Outputs & LEDs6 Safe Inputs & LEDs Power & LEDEthernet PortRO1 and RO2 LEDsRelay Output 1 (RO1)• 6 Amps Total 240Vac / 24 Vdc • 3 NO sets of contacts Relay Output 2 (RO2)• 6 Amps Total 240Vac / 24 Vdc • 3 NO sets of contactsFigure 1. Features and IndicatorsSC10-2 SpecificationsPowerVoltage: 24 V dc ±20% (SELV)Current:240 mA maximum, no load (relays on)530 mA maximum, full load (IO1 to IO4 used as auxiliary outputs)Safety Inputs (and Convertible I/O when used as inputs)Input On threshold: > 15 V dc (guaranteed on), 30 V dc maximum Input Off threshold: < 5 V dc and < 2 mA, –3 V dc minimumInput On current: 5 mA typical at 24 V dc, 50 mA peak contact cleaning current at 24 V dcInput lead resistance: 300 Ω maximum (150 Ω per lead)Input requirements for a 4-wire Safety Mat:· Maximum capacity between plates: 0.22 μF 1· Maximum capacity between bottom plate and ground: 0.22 μF 1· Maximum resistance between the 2 input terminals of one plate: 20 ΩConvertible I/OSourcing current: 80 mA maximum (overcurrent protected)Test Pulses: ~1 ms every 25 to 75 ms Automatic Terminal Optimization FeatureUp to three devices connected with user-provided terminal blocks Network InterfaceEthernet 10/100 Base-T/TX, RJ45 modular connector Selectable auto negotiate or manual rate and duplex Auto MDI/MDIX (auto cross)Protocols: EtherNet/IP (with PCCC), Modbus/TCP, and PROFINETData : 256 virtual Status Outputs; fault diagnostic codes and messages;access to fault logSC10-2 Safety ControllerOriginal Document 209715 Rev. D26 April 2019209715Response and Recovery TimesInput to Output Response Time (Input Stop to Output Off): see theConfiguration Summary in the Software, as it can varyInput Recovery Time (Stop to Run): 250 ms typical, 400 ms maximumVirtual Input (Mute Enable and On/Off) Timing: RPI + 200 ms typicalVirtual Input (Manual Reset and Cancel Delay) Timing: see the Instruction Manual for detailsDelay Tolerance±(0.02% + 2 scan times)Safety Outputs3 NO sets of contacts for each output channel (RO1 and RO2). Eachnormally open output is a series connection of contacts from two forced-guided (mechanically linked) relays. RO1 consists of relays K1 and K2. RO2 consists of relays K3 and K4.See the Instruction Manual for output ratings.Operating ConditionsTemperature: 0 °C to +55 °C (+32 °F to +131 °F) (see Temperature Derating graph)Storage Temperature: –30 °C to +65 °C (–22 °F to +149 °F)Humidity: 90% at +50 °C maximum relative humidity (non-condensing) Operating Altitude: 2000 m maximum (6562 ft maximum)Environmental RatingNEMA 1 (IEC IP20), for use inside NEMA 3 (IEC IP54) or better enclosure Mechanical StressShock: 15 g for 11 ms, half sine, 18 shocks total (per IEC 61131-2)Vibration: 3.5 mm occasional / 1.75 mm continuous at 5 Hz to 9 Hz, 1.0 g occasional and 0.5 g continuous at 9 Hz to 150 Hz: all at 10 sweep cycles per axis (per IEC 61131-2)EMCMeets or exceeds all EMC requirements for immunity per IEC61326-3-1:2012 and emissions per CISPR 11:2004 for Group 1, Class A equipmentSafetyCategory 4, PL e (EN ISO 13849)SIL CL 3 (IEC 62061, IEC 61508)Safety RatingsPFH [1/h]: 5.01 × 10-10Proof Test Interval: 20 yearsProduct Performance StandardsSee Standards and Regulations section in the Instruction Manual for a list of industry applicable U.S. and international standardsCertificationsNRGFRequired Overcurrent ProtectionWARNING: Electrical connections must bemade by qualified personnel in accordance withlocal and national electrical codes andregulations.Overcurrent protection is required to be provided by end productapplication per the supplied table.Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply.Supply wiring leads < 24 AWG shall not be spliced.For additional product support, go to .Banner Engineering Corp. Limited WarrantyBanner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to:.For patent information, see /patents.SC10-2 Safety Controller© Banner Engineering Corp. All rights reserved。

3KC ATC6300 自动转换控制器设备手册说明书

4.5 4.5.1 4.5.2
ATC6300 的显示页面....................................................................................................30 显示页面说明 ...............................................................................................................30 滚动显示页面 ...............................................................................................................41
2.1
ATC6300 自动转换控制器的属性 ..................................................................................15
2.2
兼容的西门子 SENTRON 开关设备.................................................................................17
3.3
电压控制 ......................................................................................................................22
4 产品描述 .........................................................................................................................................25