常用插脚安规尺寸
各国插脚标准
Measured (mm)
澳规插脚尺寸要求之一
澳规插脚尺寸要求之二
阿规插脚尺寸要求之一
阿规插脚尺寸要求之二
Symbol
Requirement (mm)
A
8.0 min.
B
7.92
C
7.92
D
6.86
E
6.86
F
60
G
60
Measured (mm)
Symbol H I J K L M N
Requirement (mm) 1205 13.72 6.25 6.25
美规/墨西哥规插脚尺寸要求之一
尺寸没有标明公差的数字以±0.005为公差,所有单位均为inch; 标注角度的地方没有注明公差的以±1度为公差;
美规/墨西哥规插脚尺寸要求之二
尺寸没有标明公差的数字以±0.005为公差,所有单位均为inch; 标注角度的地方没有注明公差的以±1度为公差;
韩规插脚尺寸要求之一
课堂公约
请将手机调整至静音状态 积极回应、大胆参与
我们将要掌握的内容
一般常用有哪些插脚方式 各种插脚方式的尺寸要求如何
我们将要掌握的内容
一般插脚方式
欧规、英规、美规、韩规、日规、中 规、澳规、阿规共八种
欧规插脚尺寸要求之一
欧规插脚尺寸要求之二
英规插脚尺寸要求之一
英规插脚尺寸要求之二
韩规插脚尺寸要求之二
日规插脚尺寸要求之一
日规插脚尺寸要求之二
日规插脚尺寸要求之三
日规插脚尺寸要求之四
中规插脚尺寸要求之一
中规插脚尺寸要求之二
Symbol
A B C D
Requirement (mm)
1.4 ~ 1.5 6.18 ~ 6.4 12.565 ~ 12.835 15.65 ~ 16.35
各种安规插脚尺寸
Locations Size (mm) Tolerance(mm)a 45°--b 26,1 ±0,5c 5,0 +1d 35,3 ±0,7e 13,7 ±0,7f 18 – 19,2 --g 17 – 18 --h Ø4,0 ±0,06i Ø3,8 max.k Ø4,0 max.l 19,0 ±0,5m 10,0 +1n 0 – 4,0 --o 18,0 min.Locations Size (mm) ToleranceMeasured (for both L and N pins, if applicable) (mm)(mm) Sample No.: Sample No.: Sample No.: a1 25.37 max.a2 25.37 max.b1 11.05 – 11.18b2 11.05 – 11.18c 34.6 max.d R 15 min.e 9.5 min.f 17.7 ±0.5 / / /g 1.6 ±0.25h 22.73 ±0.5i 22.23 ±0.13j 9.5 max. / / / k 9.2 max. / / / l (7.75 for ISOD) 7.80 – 8.05m 3.90 – 4.05 / / / n 3.90 – 4.05o1 6.35 ±0.13o2 6.35 ±0.13p 3.90 – 4.05q 1.2 – 2.0r 1.6 ±0.25s R 0.1 – 1.0u 60° – 80°t 60°±2°(I) Permitted additional chamfers on L and N pins used? (Yes/No)Locations Size (mm) ToleranceMeasured (for both L and N pins, if applicable) (mm)(mm) Sample No.: Sample No.: Sample No.:A 60°±2°B 1.6 ±0.25(II) Alt. method of forming 58o to 60o included chamfer on pin ends used? (Yes/No)C 60°±2°D 1.6 ±0.25(III) Alt. method of forming main chamfer on pin ends used? (Yes/No)E 0.2 max.F 1.6 ±0.25(IV) Concave shrinkage allowance for solid ISOD?G 7.75 – 8.05H 3.90 – 4.05I1 0.15 max.I2 0.15 max.I3 0.15 max.I4 0.15 max.(V) Concave shrinkage allowance for castellated ISOD?J1 7.75 – 8.05J2 0.13J1 min.J3 0.13J1 min.K 3.90 – 4.05L1 0.15 max.L2 0.15 max.L3 0.15 max.L4 0.15 max.The outline of the plug does not exceed the dimensions shown above for a distance ___________mm (required: min. 6.35mm) from the engagement surface.Au plug of pinLocations Size(mm) Tolerance (mm)R 0.35 ±0.05 S 0.9 ±0.1 T ≥0.60 -- V 6--Locations Size (mm) Tolerance (mm)A 6.35 ±0.15C (both pins) 1.63 ±0.15D (nominal) 7.92 --F 17.06 ±0.41 21.9 max. or 27.0 min. --2 21.9 max. or 27.0 min. --3 21.9 max. or 27.0 min. --4 21.9 max. or 27.0 min. --5 60°--6 60°--7 > 8.6 --8 < 21.0 --9 20.0 ±1.010 <1.0 --11 8.7 ±0.5US plug DimensionLocations Size (mm)1 1.651.402 1.651.403 6.606.104 13.775 18.2415.886 3.967 3.18From live pins to the edgeChina plug DimensionDimensions Size (mm) Tolerance (mm)A 1.5 -0.1B 6.4 -0.22C 12.7 ±0.135D 16 ±0.35From live pins to the edge > 6.5。
各国插头标准规定尺寸
各国插头标准规定尺寸中国标准电源插头227IEC42(RVB)2×0.5mm26A250V227IEC42(RVB)2×0.75mm26A250V 227IEC52(RVV)2×0.5mm26A250V227IEC52(RVV)2×0.75mm26A250V227IEC52(RVV) 2×0.75mm26A250V 227IEC53(RVV) 2×0.75mm26A250V 227IEC53(RVV) 2×1.0mm210A250V227IEC42(RVB)2×0.5mm26A250V227IEC42(RVB)2×0.75mm26A250V 227IEC52(RVV)2×0.5mm26A250V227IEC52(RVV)2×0.75mm26A250V227IEC52（RVV）3×0.5mm26A250V 227IEC52（RVV）3×0.75mm26A250V 227IEC53（RVV）3×0.75mm26A250V 227IEC53（RVV）3×1.0mm210A250V227IEC52（RVV）3×0.5mm26A250V 227IEC52（RVV）3×0.75mm26A250V 227IEC53（RVV）3×0.75mm26A250V 227IEC53（RVV）3×1.0mm210A250V227IEC52（RVV）3×0.5mm26A250V227IEC52（RVV）3×0.75mm26A250V227IEC53（RVV）3×0.75mm26A250V227IEC53（RVV）3×1.0mm210A250VRX 300/300V 3×0.75mm26A250VRX 300/300V 3×1.0mm210A250V欧洲标准电源插头H03VVH2 -F2X0.5mm210/16A250V H03VVH2 -F2X0.75mm210/16A250V H03VV-F2X0.5mm210/16A250V H03VV-F2X0.75mm210/16A250VH05VVH2 -F2X0.75mm210/16A250V H05VVH2 -F2X1.0mm210/16A250V H05VV-F2X0.75mm210/16A250V H05VV-F2X1.0mm210/16A250VH03VVH2 -F2X0.5mm2 2.5A250VH03VVH2 -F2X0.75mm2 2.5A250VH03VV-F2X0.5mm2 2.5A250VH03VV-F2X0.75mm2 2.5A250VH05VVH2 -F2X0.75mm210A250VH05VVH2 -F2X1.0mm210A250VH05VV-F2X0.75mm210A250VH05VV-F2X1.0mm210A250VH03VVH2 -F2X0.5mm2 2.5A250VH03VVH2 -F2X0.75mm2 2.5A250VH03VV-F2X0.5mm2 2.5A250VH03VV-F2X0.75mm2 2.5A250VH05VVH2 -F2X0.75mm210A250VH05VVH2 -F2X1.0mm210A250VH05VV-F2X0.75mm210A250VH05VV-F2X1.0mm210A250VH03VV-F3G0.5mm210/16A250V H03VV-F3G0.75mm210/16A250V H05VV-F3G0.75mm210/16A250V H05VV-F3G1.0mm210/16A250V H05VV-F3G1.5mm210/16A250VH03VV-F3G0.5mm210/16A250V H03VV-F3G0.75mm210/16A250V H05VV-F3G0.75mm210/16A250V H05VV-F3G1.0mm210/16A250V H05VV-F3G1.5mm210/16A250VH03VV-F3G0.5mm210A250VH03VV-F3G0.75mm210A250VH05VV-F3G0.75mm210A250VH05VV-F3G1.0mm210A250VH03VV-F3G0.5mm210A250VH03VV-F3G0.75mm210A250VH05VV-F3G0.75mm210A250VH05VV-F3G1.0mm210A250V227IEC52(RVV)3X0.75mm210A250V227IEC53(RVV)3X0.75mm210A250V227IEC53(RVV)3X1.0mm210A250V H03VV-F3G0.75mm26A250V H05VV-F3G0.75mm210A250V* * H05VV-F3G1.0mm210A250V227IEC52(RVV)3X0.75mm210A250V227IEC53(RVV)3X0.75mm210A250V227IEC53(RVV)3X1.0mm210A250VH03VV-F3G0.75mm26A250VH05VV-F3G0.75mm210A250VH05VV-F3G1.0mm210A250V 澳大利亚标准电源插头SAAH05VVH2 -F2X0.75mm27.5A250VH05VV-F2X0.75mm27.5A250VH05VV-F2X1.0mm210A250VH05VVH2 -F2X0.75mm27.5A250VH05VV-F2X0.75mm27.5A250V H05VV-F2X1.0mm210A250VH05VV-F3G0.75mm27.5A250VH05VV-F3G1.0mm210A250VH05VV-F3G1.5mm215A250V美国标准电源插头C-ULSPT-118AWG/2CSPT-218AWG/2CSPT-216AWG/2CSPT-318AWG/2CSPT-316AWG/2CSVT18AWG/2CSVT17AWG/2C18AWG/2C NISPT-1NISPT-218AWG/2CSVT18AWG/2C SVT17AWG/2CST18AWG/2CST16AWG/2C SJT18AWG/2C SJT16AWG/2C NISPT-118AWG/2C NISPT-218AWG/2CSVT18AWG/2C SVT17AWG/2C SVT18AWG/2C(齿形) SVT17AWG/2C(齿形)ST18AWG/2C ST16AWG/2CSPT-118AWG/3CSPT-218AWG-16AWG/3CSPT-318AWG-16AWG/3CSVT18AWG- 17AWG/3CSVT18AWG-17AWG/3C(齿形) ST18AWG-16AWG/3C SJT 18AWG-16AWG/3CSVT18AWG/3CSVT17AWG/3CSVT18AWG/3C(齿形)SVT17AWG/3C(齿形)ST18AWG/3CST16AWG/3CSJT 16AWG/3CSJT 18AWG/3C日本标准电源插头VFF2X0.75mm27A125VVCTF2X0.75mm27A125VVCTFK2X0.75mm27A125V以色列南非英国电源插头H03VV-F3G0.75mm2H05VV-F3G0.75mm2H05VV-F3G1.0mm2H05VV-F3G1.5mm2H03VV-F3G0.75mm2H05VV-F3G0.75mm2H05VV-F3G1.0mm2H05VV-F3G1.5mm2H03VV-F3G0.5mm2H03VV-F3G0.75mm2H05VV-F3G0.75mm2H05VV-F3G1.0mm2H05VV-F3G1.5mm2欧洲标准电源线·标准:DIN VDE0281·型号:H03VVH2-F H03VV-FH05VVH2-F H05VV-F·额定电压:H03 300/300VH05 300/500V·应用:H03型适用小功率家用电器、电动工具及动力照明等。
各国插脚标准
D
15.65 ~ 16.35
澳规插脚尺寸要求之一
澳规插脚尺寸要求之二
阿规插脚尺寸要求之一
阿规插脚尺寸要求之二
Symbol Requirement (mm) Measured (mm) Symbol Requirement (mm) Measured (mm) A 8.0 min. H 1205
欧规插脚尺寸要求之一
欧规插脚尺寸要之二
美规/墨西哥规插脚尺寸要求之一
尺寸没有标明公差的数字以±0.005为公差,所有单位均为inch; 标注角度的地方没有注明公差的以± 1度为公差;
美规/墨西哥规插脚尺寸要求之二
尺寸没有标明公差的数字以±0.005为公差,所有单位均为inch; 标注角度的地方没有注明公差的以± 1度为公差;
韩规插脚尺寸要求之一
韩规插脚尺寸要求之二
日规插脚尺寸要求之一
日规插脚尺寸要求之二
日规插脚尺寸要求之三
日规插脚尺寸要求之四
中规插脚尺寸要求之一
中规插脚尺寸要求之二
Symbol Requirement (mm) Measured (mm)
A
1.4 ~ 1.5
B
6.18 ~ 6.4
C
12.565 ~ 12.835
安规插脚尺寸要求
安规插脚尺寸要求介绍
讲 解 人：pingping.Guo 2009年8月
课堂公约
请将手机调整至静音状态 积极回应、大胆参与
我们将要掌握的内容
一般常用有哪些插脚方式 各种插脚方式的尺寸要求如何
我们将要掌握的内容
一般插脚方式
欧规、英规、美规、韩规、日规、中 规、澳规、阿规共八种
B
7.92
I
各国插脚安规尺寸标准
目录1、VDE欧规胶壳插脚：标准-EN50075/IEC600832、BS英规胶壳插脚：标准-BS13633、SAA澳规胶壳插脚：标准-AS/NZS31124、UL美规胶壳插脚：标准-ANSI-NEMA WD65、CCC中国规胶壳插脚：标准-GB1002-20086、Korea韩国胶壳插脚：标准-KSC83057、Brasil巴西规胶壳插脚：NBR141368、India印度胶壳插脚：标准IS12939、Argentina阿根廷胶壳插脚：IRAM206310、SASO沙特胶壳插脚：SASO-220311、JAPAN日本胶壳插脚：JISC830312、小南非规胶壳插脚：SABS164-1修订记录2013-10-15修改：1、GB1002-2008版CCC插脚（厚1.4-1.5mm）增加插头插销离边沿的距离不小于6.5mm。
2、增加日规插脚安规尺寸图表，日规插脚（厚1.4-1.6mm）备注“L"的尺寸要求不大于0.9mm，及插头插销离边沿的距离不小于5.1mm。
3、修改美规插脚安规尺寸，美规插脚（厚1.40-1.65mm），备注插头插销离边沿的距离不小于5.1mm.。
4、插脚图示缩小2PIN欧洲插脚Two-pin plugs f(Up to2.5A rating)EN50075/IEC60083-C5/CEE7/DIN49464P≥4.0,Q≥18.0,I：金属下部结合部分边缘应光滑钝化,不得尖锐刺手.此插脚适应国家包括:德国,俄罗斯,以色列英国插脚UK Plug Checking Form according to Figure 4of BS1363BS-3Symbol Requirement(mm)Symbol Requirement (mm)Symbol Requirement(mm)Symbol Requirement(mm)A 25.37max.I 22.10-22.36Q 17.2-18.2Y 1.2-2.0B25.37max.J 22.23-23.23R 6.22-6.48Z R 0.1-1.0C34.6max.K 1.35-1.85S 3.90-4.05a 58︒-62︒D11.05-11.18L 7.80-8.05T 6.22-6.48b 1.35-1.85E11.05-11.18M 58︒-62︒U 6.35min.c 58︒-62︒FR 15min.N 3.90-4.05V 60︒-80︒d 1.35-1.85GR 9.5min.O 9.2max.W 1.35-1.85e 0.2max.H R 9.5min.P 9.5max.X 3.90-4.05f 1.35-1.85此插脚适应国家包括:英国、新加坡、马来西亚Grounding pin澳规插脚AS/NZS3112Standard sheet Figure 2.1(a1)or 2.1(c)Standard sheet Figure 2.1(e)and fig 2.4PositionRequired (mm)By Measurement (mm)By the gauges in Figure A1A6.35±0.15-B6.35±0.15C+0.150.051.63--D7.92--E10.31--F17.06±0.4-G19.94±0.81、2、3、421.9max.or 27.0min.-5、660︒--78.6min.-821.0max.-920.0±1.0-101.0max -118.7±0.5-Distance fromprojection part edge toL and N pins 9mm min.美国插脚UL插脚：According toUL1310/UL498/UL817/UL1659/ANSI-NEMA WD6-2002Figure1-15备注：关于电源插墙式插脚（UL1310)中7.16条款要求：起始于金属插脚的任意一点，与金属插脚的托台圆周边之间的距离不得小于5.1mm。
插脚安规尺寸
VDE PLUG DIMENSION (mm)Two-pin plugs for class II appliances (Up to 2.5 A rating)According to EN50075 - Standard Sheet and IEC60083 - Standard C5金属下部结合部分边缘应光滑钝化，不得尖锐刺手。
欧洲VDE PLUG DIMENSION CHECK LIST.从外壳圆周面延伸到PIN脚与托台结合处任意点之间的距离最小为18mmDimension Checking for Two-pin plugs of NA (15 A, 125 V)According to ANSI/UL 1310 and ANSI/UL 1861 (NEMA Figure 1-15)UL PLUG DIMENSION CHECK LIST公差为± 0.127mm符号标准值 (mm) 测量值(mm) 符号标准值(mm) 测量值 (mm)A 3.175 E 6.60≥ E ≥ 6.09B 3.96 F 8.17 ≥ F ≥ 7.80C 13.77G 1.65 ≥ G ≥ 1.40D 18.23 ≥ D ≥ 15.86 H 12.7起始于金属插脚的任意一点，与金属插脚的托台圆周边之间的距离不得小于7.9 mmAccording to Figure 4 of BS1363Grounding pinBS PLUG DIMENSION CHECK LIST.英SAA PLUG DIMENSION (mm)澳According to AS/NZS 3112:1993 Two-pin plugs (Up to 10 A rating)符号标准值 (mm) 测量值(mm) 符号标准值 (mm) 测量值(mm)A < 21.9 or > 27.0 H 1.58 – 1.78B < 21.9 or > 27.0 I 16.66 – 17.46C < 21.9 or > 27.0 J 8.6minD < 21.9 or > 27.0 K R 21.0 maxE 60 L R 19.0 – 21.0F 6.2 – 6.5 M R 1.0 maxG 7.92According to AS/NZS 3112:1993 Three-pin plugs (10 A or 15A rating)符号标准值(mm) 测量值(mm) 符号标准值 (mm) 测量值(mm)A 6.2 ～ 6.5 J < 21.9 or > 27.0B 6.2～ 6.5 K < 21.9 or > 27.0C 1.58 ～ 1.78 L 60 ︒D 7.92 M 60 ︒E 10.31 N 8.6minF 16.66 ～ 17.46 O R 19.0 – 21.0G 19.14 ～ 20.74 P R 21.0 maxH < 21.9 or > 27.0 Q R 1.0 maxI < 21.9 or > 27.0According to Fig 1 of GB 1002-1996 Tow-pin plugs (6 A, 10 A rating)CHINA PLUG DIMENSION CHECK LIST.符号标准值(mm) 测量值(mm)A 1.4 ~ 1.5B 6.18 ~ 6.4C 12.565 ~ 12.835D 15.65 ~ 16.35According to Fig 1 of GB 1002-1996 Three-pin plugs (Up to 6 A rating)CHINA PLUG DIMENSION CHECK LIST.符号标准值 (mm) 测量值 (mm)A 120B 7.79 – 8.01C 1.4 – 1.5D 6.18 – 6.4E 20.58 – 21.42F 17.65 – 18.35According to KSC 8305 Two-pole plug for 3A 250VKOREA PLUG DIMENSION CHECK LIST.JAPAN PLUG DIMENSION (mm)According to EMA Figure 1-15 Two-pin plugs of JP (15 A, 125 V)JAPAN PLUG DIMENSION CHECK LIST.符号标准值(mm) 测量值(mm) 符号标准值 (mm) 测量值(mm)A 3.3 ≥ A ≥2.8 E 6.6 ≥ E ≥ 6.0B 3.5以上 F 8.2 ≥ F ≥ 7.8C 13.75≥ C ≥ 12.7G 1.6 ≥ G ≥1.4D 18.3 ≥ D ≥ 15.7 H 12.7起始于金属插脚的任意一点，与金属插脚的托台圆周边之间的距离不得小于7.9 mm金属插脚孔内圆中心到插脚托台面的距离为11.7±0.4金属PIN脚末端厚度为0.9mm以下。
各国插头规范标准尺寸
中国标准电源插头227IEC42(RVB)2×0.5mm²6A250V227IEC42(RVB)2×0.75mm²6A250V227IEC52(RVV)2×0.5mm²6A250V227IEC52(RVV)2×0.75mm²6A250V227IEC52(RVV) 2×0.75mm²6A250V227IEC53(RVV) 2×0.75mm²6A250V227IEC53(RVV) 2×1.0mm²10A250V227IEC42(RVB)2×0.5mm²6A250V227IEC42(RVB)2×0.75mm²6A250V227IEC52(RVV)2×0.5mm²6A250V227IEC52(RVV)2×0.75mm²6A250V227IEC52（RVV）3×0.5mm²6A250V 227IEC52（RVV）3×0.75mm²6A250V 227IEC53（RVV）3×0.75mm²6A250V 227IEC53（RVV）3×1.0mm²10A250V227IEC52（RVV）3×0.5mm²6A250V 227IEC52（RVV）3×0.75mm²6A250V 227IEC53（RVV）3×0.75mm²6A250V 227IEC53（RVV）3×1.0mm²10A250V227IEC52（RVV）3×0.5mm²6A250V227IEC52（RVV）3×0.75mm²6A250V227IEC53（RVV）3×0.75mm²6A250V227IEC53（RVV）3×1.0mm²10A250VRX 300/300V 3×0.75mm²6A250VRX 300/300V 3×1.0mm²10A250V欧洲标准电源插头H03VVH2 -F2X0.5mm²10/16A250V H03VVH2 -F2X0.75mm²10/16A250V H03VV-F2X0.5mm²10/16A250V H03VV-F2X0.75mm²10/16A250VH05VVH2 -F2X0.75mm²10/16A250V H05VVH2 -F2X1.0mm²10/16A250V H05VV-F2X0.75mm²10/16A250V H05VV-F2X1.0mm²10/16A250VH03VVH2 -F2X0.5mm² 2.5A250VH03VVH2 -F2X0.75mm² 2.5A250VH03VV-F2X0.5mm² 2.5A250VH03VV-F2X0.75mm² 2.5A250VH05VVH2 -F2X0.75mm²10A250VH05VVH2 -F2X1.0mm²10A250VH05VV-F2X0.75mm²10A250VH05VV-F2X1.0mm²10A250VH03VVH2 -F2X0.5mm² 2.5A250VH03VVH2 -F2X0.75mm² 2.5A250VH03VV-F2X0.5mm² 2.5A250VH03VV-F2X0.75mm² 2.5A250VH05VVH2 -F2X0.75mm²10A250VH05VVH2 -F2X1.0mm²10A250VH05VV-F2X0.75mm²10A250VH05VV-F2X1.0mm²10A250VH03VV-F3G0.5mm²10/16A250V H03VV-F3G0.75mm²10/16A250V H05VV-F3G0.75mm²10/16A250V H05VV-F3G1.0mm²10/16A250V H05VV-F3G1.5mm²10/16A250VH03VV-F3G0.5mm²10/16A250V H03VV-F3G0.75mm²10/16A250V H05VV-F3G0.75mm²10/16A250V H05VV-F3G1.0mm²10/16A250V H05VV-F3G1.5mm²10/16A250VH03VV-F3G0.5mm²10A250VH03VV-F3G0.75mm²10A250VH05VV-F3G0.75mm²10A250VH05VV-F3G1.0mm²10A250VH03VV-F3G0.5mm²10A250VH03VV-F3G0.75mm²10A250VH05VV-F3G0.75mm²10A250VH05VV-F3G1.0mm²10A250V227IEC52(RVV)3X0.75mm²10A250V 227IEC53(RVV)3X0.75mm²10A250V 227IEC53(RVV)3X1.0mm²10A250V H03VV-F3G0.75mm²6A250V H05VV-F3G0.75mm²10A250V,. H05VV-F3G1.0mm²10A250V227IEC52(RVV)3X0.75mm²10A250V227IEC53(RVV)3X0.75mm²10A250V227IEC53(RVV)3X1.0mm²10A250VH03VV-F3G0.75mm²6A250VH05VV-F3G0.75mm²10A250VH05VV-F3G1.0mm²10A250V 澳大利亚标准电源插头SAAH05VVH2 -F2X0.75mm²7.5A250VH05VV-F2X0.75mm²7.5A250VH05VV-F2X1.0mm²10A250VH05VVH2 -F2X0.75mm²7.5A250VH05VV-F2X0.75mm²7.5A250V H05VV-F2X1.0mm²10A250VH05VV-F3G0.75mm²7.5A250VH05VV-F3G1.0mm²10A250VH05VV-F3G1.5mm²15A250V美国标准电源插头C-ULSPT-118AWG/2CSPT-218AWG/2CSPT-216AWG/2CSPT-318AWG/2CSPT-316AWG/2CSVT18AWG/2CSVT17AWG/2C18AWG/2C NISPT-1NISPT-218AWG/2CSVT18AWG/2C SVT17AWG/2CST18AWG/2CST16AWG/2C SJT18AWG/2C SJT16AWG/2C NISPT-118AWG/2C NISPT-218AWG/2CSVT18AWG/2C SVT17AWG/2C SVT18AWG/2C(齿形) SVT17AWG/2C(齿形)ST18AWG/2C ST16AWG/2CSPT-118AWG/3CSPT-218AWG-16AWG/3CSPT-318AWG-16AWG/3CSVT18AWG- 17AWG/3CSVT18AWG-17AWG/3C(齿形) ST18AWG-16AWG/3CSJT 18AWG-16AWG/3CSVT18AWG/3CSVT17AWG/3CSVT18AWG/3C(齿形)SVT17AWG/3C(齿形)ST18AWG/3CST16AWG/3CSJT 16AWG/3CSJT 18AWG/3C日本标准电源插头VFF2X0.75mm²7A125VVCTF2X0.75mm²7A125VVCTFK2X0.75mm²7A125V以色列南非英国电源插头H03VV-F3G0.75mm²H05VV-F3G0.75mm²H05VV-F3G1.0mm²H05VV-F3G1.5mm²H03VV-F3G0.75mm²H05VV-F3G0.75mm²H05VV-F3G1.0mm²H05VV-F3G1.5mm²H03VV-F3G0.5mm²H03VV-F3G0.75mm²H05VV-F3G0.75mm²H05VV-F3G1.0mm²H05VV-F3G1.5mm²欧洲标准电源线·标准:DIN VDE0281·型号:H03VVH2-F H03VV-FH05VVH2-F H05VV-F·额定电压:H03 300/300VH05 300/500V·应用:H03型适用小功率家用电器、电动工具及动力照明等。
2013.10.OK-各国插脚安规尺寸标准
Symbol I J K L M N O P
Requirement (mm) 22.10-22.36 22.23-23.23 1.35-1.85 7.80-8.05 58-62 3.90-4.05 9.2 max. 9.5 max.
Symbol Q R S T U V W X
Requirement (mm) 17.2-18.2 6.22-6.48 3.90-4.05 6.22-6.48 6.35 min. 60-80 1.35-1.85 3.90-4.05
小南非插脚
Symbol
Requirement (mm)
Measured (mm)
Symbol
Requirement (mm)
Measured (mm)
B C D E F G ① ② ③
25.5 - 26.5 90 - 92 R 5.0 – 6.0 35.0 – 36.0 13.0 – 14.4 18.8 – 19.2 > 14 mm See above See above
Symbol Y Z a b c d e f
Requirement (mm) 1.2-2.0 R 0.1-1.0 58-62 1.35-1.85 58-62 1.35-1.85 0.2 max. 1.35-1.85
此插脚适应国家包括:英国、新加坡、马来西亚
澳规插脚 AS/NZS3112
Standard sheet Figure 2.1 (a1) or 2.1(c)
22.22±0.15 19.1±0.15 7.010-7.085 5.030-5.105 15.77-16.94 20.47-21.64 ≥7.94
28.6±0.15 25.4±0.15 8.660-8.735 7.010-7.085 20ห้องสมุดไป่ตู้47-21.64 28.47-29.64 ≥9.52
各国标准插头_实物图,尺寸图
227IEC42(RVB)2×0.5mm² 6A250V 227IEC42(RVB)2×0.75mm² 6A250V 227IEC52(RVV)2×0.5mm² 6A250V 227IEC52(RVV)2×0.75mm² 6A250V
227IEC52(RVV) 2×0.75mm² 6A250V 227IEC53(RVV) 2×0.75mm² 6A250V 227IEC53(RVV) 2×1.0mm² 10A250V
SVT
18AWG/3C
SVT
17AWG/3C
SVT
18AWG/3C(齿形)
SVT
17AWG/3C(齿形)
ST
18AWG/3C
ST
16AWG/3C
SJT
16AWG/3C
SJT
18AWG/3C
日本标准电源插头
VFF VCTF VCTFK
2X0.75mm² 2X0.75mm² 2X0.75mm²
7A125V 7A125V 7A125V
SVT
18AWG/2C
SVT
17AWG/2C
SVT
18AWG/2C(齿形)
SVT
17AWG/2C(齿形)
ST
18AWG/2C
ST
16AWG/2C
SPT-1 SPT-2 SPT-3 SVT SVT ST SJT
18AWG/3C 18AWG-16AWG/3C 18AWG-16AWG/3C 18AWG- 17AWG/3C 18AWG-17AWG/3C(齿形) 18AWG-16AWG/3C 18AWG-16AWG/3C
2X0.5mm² 2X0.75mm² 2X0.5mm² 2X0.75mm² 2X0.75mm² 2X1.0mm² 2X0.75mm² 2X1.0mm²
插脚安规尺寸
VDE PLUG DIMENSION (mm)Two-pin plugs for class II appliances (Up to 2.5 A rating)According to EN50075 - Standard Sheet and IEC60083 - Standard C5金属下部结合部分边缘应光滑钝化，不得尖锐刺手。
欧洲VDE PLUG DIMENSION CHECK LIST.从外壳圆周面延伸到PIN脚与托台结合处任意点之间的距离最小为18mmDimension Checking for Two-pin plugs of NA (15 A, 125 V)According to ANSI/UL 1310 and ANSI/UL 1861 (NEMA Figure 1-15)UL PLUG DIMENSION CHECK LIST公差为± 0.127mm符号标准值 (mm) 测量值(mm) 符号标准值(mm) 测量值 (mm)A 3.175 E 6.60≥ E ≥ 6.09B 3.96 F 8.17 ≥ F ≥ 7.80C 13.77G 1.65 ≥ G ≥ 1.40D 18.23 ≥ D ≥ 15.86 H 12.7起始于金属插脚的任意一点，与金属插脚的托台圆周边之间的距离不得小于7.9 mmAccording to Figure 4 of BS1363Grounding pinBS PLUG DIMENSION CHECK LIST.英SAA PLUG DIMENSION (mm)澳According to AS/NZS 3112:1993 Two-pin plugs (Up to 10 A rating)符号标准值 (mm) 测量值(mm) 符号标准值 (mm) 测量值(mm)A < 21.9 or > 27.0 H 1.58 – 1.78B < 21.9 or > 27.0 I 16.66 – 17.46C < 21.9 or > 27.0 J 8.6minD < 21.9 or > 27.0 K R 21.0 maxE 60 L R 19.0 – 21.0F 6.2 – 6.5 M R 1.0 maxG 7.92According to AS/NZS 3112:1993 Three-pin plugs (10 A or 15A rating)符号标准值(mm) 测量值(mm) 符号标准值 (mm) 测量值(mm)A 6.2 ～ 6.5 J < 21.9 or > 27.0B 6.2～ 6.5 K < 21.9 or > 27.0C 1.58 ～ 1.78 L 60 ︒D 7.92 M 60 ︒E 10.31 N 8.6minF 16.66 ～ 17.46 O R 19.0 – 21.0G 19.14 ～ 20.74 P R 21.0 maxH < 21.9 or > 27.0 Q R 1.0 maxI < 21.9 or > 27.0According to Fig 1 of GB 1002-1996 Tow-pin plugs (6 A, 10 A rating)CHINA PLUG DIMENSION CHECK LIST.符号标准值(mm) 测量值(mm)A 1.4 ~ 1.5B 6.18 ~ 6.4C 12.565 ~ 12.835D 15.65 ~ 16.35According to Fig 1 of GB 1002-1996 Three-pin plugs (Up to 6 A rating)CHINA PLUG DIMENSION CHECK LIST.符号标准值 (mm) 测量值 (mm)A 120B 7.79 – 8.01C 1.4 – 1.5D 6.18 – 6.4E 20.58 – 21.42F 17.65 – 18.35According to KSC 8305 Two-pole plug for 3A 250VKOREA PLUG DIMENSION CHECK LIST.JAPAN PLUG DIMENSION (mm)According to EMA Figure 1-15 Two-pin plugs of JP (15 A, 125 V)JAPAN PLUG DIMENSION CHECK LIST.符号标准值(mm) 测量值(mm) 符号标准值 (mm) 测量值(mm)A 3.3 ≥ A ≥2.8 E 6.6 ≥ E ≥ 6.0B 3.5以上 F 8.2 ≥ F ≥ 7.8C 13.75≥ C ≥ 12.7G 1.6 ≥ G ≥1.4D 18.3 ≥ D ≥ 15.7 H 12.7起始于金属插脚的任意一点，与金属插脚的托台圆周边之间的距离不得小于7.9 mm金属插脚孔内圆中心到插脚托台面的距离为11.7±0.4金属PIN脚末端厚度为0.9mm以下。