PT6520_Natertech
贝利摩环境传感器P-01RT-5说明书
Sensor de ambiente para temperaturaSensores de temperatura pasivos de montaje en pared con ajuste de setpoint. Diseño elegante que incorpora un botón de control manual. Disponible con cuatro salidasdiferentes para conectarse sin problemas a los controladores de terceros existentes.Índice de modelosTipo Señal de salidaPotenciómetro P-01RT-5B-0Pt10000...1 kOhm P-01RT-5L-0NTC10k (10k2)0...10 kOhm P-01RT-5M-0NTC10k3 (Precon)0...10 kOhm P-01RT-5Q-0NTC20k0...10 kOhmDatos técnicosDatos eléctricosConexión eléctrica Bloque de terminales con resorte 0.5...1.5 mm²Entrada de cableAperturas de hilos en la parte trasera (para conexionado dentro de la pared) y en la parte superior/inferior (para conexionado sobre la pared)Datos de funcionamiento AplicaciónaireSeñal de salida pasiva de la temperaturaPt1000NTC10k (10k2)NTC10k3 (Precon)NTC20k Datos de medición Valores de mediciónTemperatura Rango de medición de temperatura 32...122°F [0...50°C]Precisión de la temperatura pasivaSensores pasivos en función del tipo utilizado Pt.. : ±0.5°F @ 32°F [±0.3°C @ 0°C]NTC.. : ±0.35°F @ 77°F [±0.2°C @ 25°C]Precisión potenciómetro típico ± 12%Corriente de mediciónPt1000: <0.3 mA @ 32°F [0°C]NTC10k2: <2 mA @ 77°F [25°C]NTC10k3: <2.7 mA @ 77°F [25°C]NTC20k: <0.5 mA @ 77°F [25°C]Constante de tiempo τ (63%) en la sala Típico 360 s Factor de acoplamiento a la pared35 %MaterialesCarcasaPC, blanco, RAL 9003Datos de seguridadHumedad ambiente Máx. 95% RH, sin condensación Temperatura ambiente30...120°F [0...50°C]Temperatura de almacenamiento -4.0...140°F [-20...60°C]Clase de protección IEC/EN III, voltaje extra bajo de protección (PELV)Conformidad UE Homologación CECertificación IEC/EN IEC/EN 60730-1 y IEC/EN 60730-2-9Grado de protección IEC/EN IP30Grado de protección NEMA/ULNEMA 1Observaciones generales sobre sensoresAccionamiento manualDatos de seguridadNorma de CalidadISO 9001Notas de seguridadEste dispositivo ha sido diseñado para su uso en sistemas estacionarios de calefacción,ventilación y aire acondicionado y no se debe utilizar fuera del campo específico de aplicación. Están prohibidas las adaptaciones no autorizadas. El producto no se debe utilizar con ningún equipo que, en caso de fallo, pueda amenazar, directa o indirectamente, la salud humana o poner en peligro la vida de seres humanos, animales o activos.Asegúrese de toda la potencia esté desconectada antes de la instalación. No lo conecte a equipos en funcionamiento.Solo especialistas autorizados deben realizar la instalación. Durante la instalación deben tenerse en cuenta las normativas legales o institucionales.El dispositivo contiene componentes electrónicos y eléctricos, y no puede desecharse junto con residuos domésticos. Deben respetarse todas las normas y requerimientos locales vigentes.ObservacionesDebido al propio calentamiento con sensores pasivos de 2 hilos, la corriente del cable de alimentación afecta a la precisión de la medición. Por tanto, la corriente de alimentación no debe superar los valores de corriente de medición especificados en esta ficha técnica.Cuando se utilizan cables de conexión largos (en función de la sección transversal usada), la resistencia del cable debe tenerse en cuenta. Cuanto más baja sea la impedancia del sensor utilizado, mayor será el efecto de la resistencia de línea sobre la medición, ya que genera un offset.Una vez que se pulsa el botón de control manual, el termistor del sensor de ambiente se cortocircuita temporalmente y se envía una señal al controlador. El programador DDC puede utilizar la señal para proporcionar una serie de opciones de secuencia HVAC.Composición del suministroTornillosEsquema de conexionadoDibujos dimensionalesTipo PesoP-01RT-5B-00.24 lb [0.11 kg]P-01RT-5L-00.24 lb [0.11 kg]P-01RT-5M-00.24 lb [0.11 kg]P-01RT-5Q-00.24 lb [0.11 kg]。
美国AEMC公司高端和可移动数字弱电阻抗度计6550和6555产品说明书
Technical Assistance (800) 343-1391 110kV and 15kV DigitalMegohmmetersModels 6550 & 6555► Insulation measurementup to 30T Ω► Test voltages up to 15,000V► Step, ramp & fixed voltagetesting► Multiple test modes: voltageramp and step with “Burn-In”, “Early-Break” and “I-Limit” modes► 3 filter choices to optimize measurement stability► Selectable voltage from40V to 10,000 / 15,000V ► Storage of up to 80,000 measurements► Optically-isolated USBcommunication for data transfer to PC and report generation using DataView ® softwareExpert tools for testing insulation safely & accuratelyIP 54Our products are backed by over 130 years of experience in test and measurement equipment, and encompass the latest international standards for quality and safety.Technical Hotline: (800) 343-13912 Technical Assistance (800) 343-1391Models 6550 & 6555HIGH-END & PORTABLEThe Megohmmeter Models 6550 and 6555 are high-end portable instruments intended for measuring a wide variety of electrical insulation resistance values oncables and devices operating at high voltage. They are packaged in a rugged case that is IP54 rated (cover closed). Test results and configuration information is provided on a graphical LCD screen, as well as exportable throughthe use of the DataView ® software provided. TheMegohmmeters can operate on battery or AC power while testing.These Megohmmeters contribute to the safety ofelectrical installations and equipment. Their operation is managed by microprocessors that acquire, process, display and store the measurements.The Model 6550 makes insulation measurements at voltages up to 10,000 V , the Model 6555 up to 15,000 V .Main Functions:• Detection and measurement of input voltage, frequency, and current prior to running a test.• Quantitative and qualitative insulation measurements.• Measurements at a fixed test voltage of 500, 1000, 2500, 5000, 10,000 or 15,000 V dc .• Measurements at an adjustable test voltagebetween 40 and 15,000 V dc preselected by the user prior to the test. Three preselected test voltages can be stored in the instrument and can be modified as needed prior to starting a test.IP 54• Ramp voltage measurements with a ramp from 40 to 10,000 V or 15,000 V , model dependent. Three ramp profiles can be stored in the instrument. Each ramp profile includes the starting and ending test voltage and the ramp time between the two.• Step voltage measurements with steps from 40 to 10,000 V or 15,000 V , model dependent.Three step voltage profiles can be stored in the instrument. Each contains up to 10 steps that include test voltage and duration.• Three test current choices: Burn-In, Early-Break and I-Limit provide qualitative analysis tools for detection breaks in insulation.• Quality ratio calculations for DAR, PI, and DD are calculated and displayed.• Temperature correction of the measured resistance to a reference temperature.• Capacitance measurement of the device tested.• Residual current measurement.Model 6555 checking insulation resistance on feed cables to a three-phase motor.Technical Assistance (800) 3►► SELECTABLE VOLTAGE FROM 40V TO 10kV / 15kV MODELSINSULATION TESTSTest VoltageAPPLICATIONS► Acceptance testing and preventive maintenance ► Test motors, cables, switchgears and wiring installations4 Technical Assistance (800) 343-1391CONTROL FEATURESFront Panel Features for Models 6550 & 6555Socket for connection to the ACpower and recharging of thebuilt-in batteriesmeasurementbuttonsUSB connector forcommunicationto a PC Seven position access to the fixed voltage, adjustable voltage,ramp and stepLarge, digital, backlit, Models 6550 and 6555 have the same front panel with differences in the display only .5Measurement Results Display AreaDisplay ofResultsTechnical Assistance (800) 5FUNCTIONSModels 6550 & 65556 Technical Assistance (800) 343-1391bargraphterminalsExample of display during measurement.resistanceresistance referred to the reference temperature.cursor Resistance versus time graph.This curve is useful primarily in the case of a measurement in V-RAMP mode.When Timed Run (test with programmed duration) or Timed Run + DD is selected, the duration of the measurement (m:s) can be set.The number of measurements that can be recorded depends on the number of samples stored for each measurement.quality ofof memory white).indicated.T est with programmed durationExample of display before measurement.FUNCTIONAL DISPLAYSSOFTWARE & ANALYSIS SCREENSEasy identification of all stored test results.Real-time display of measurement results.Step voltage set up screen.Technical Assistance (800) 7ORDERING INFORMATION M egohmmeter Model 6550 Ramp, StepV , Variable, Auto DAR/PI/DD, USB w/DataView Megohmmeter Model 6555 Ramp, StepV , Variable, Auto DAR/PI/DD, USB w/DataView AEMC ® Instruments • 15 Faraday Dr. • Dover, NH 03820 USA • (800) 343-1391•Fax(603)742-2346•E-mail:**************Export Department: +1 (603) 749-6434 x520 • Fax +1(603)742-2346•E-mail:***************© Chauvin Arnoux ®, Inc. d.b.a. AEMC ®Instruments Call the AEMC ® Instruments Technical Assistance Hotline for immediate consultation with an applications engineer: (800) 343-1391950.BR-6550-6555_0323 • Printed in the USA M u lt i-p u r p o s e C la m p -O n M e t e r s ca o tl in M E G O H MM E T E R SFo r a ll of y ou r I ns ul at io n Te st in g ne ed s...ch ni ca l H o tl in e: (800) 343-1391.a em c.co mP O W E R Q U A L I T Y Fo rA ll Y ou r Po w er Q ua li ty N ee ds ...Te 43-1391w w w ( Fo r a ll of yo ur G ro un d In te gr ity T es tin g ne ed s...G R O U N D R E S IS TA N C E T E S TE R S Te ch ni ca l H ot lin e: (800) 343-1391w w w .a em c.co mTEST & MEA SUREM ENT INSTR UMEN TSVOLUM E 23WWW.AEM TECHNICA L HOTLINE : (800) 343-1391Family of ProductsTo learn more, visit 。
OTP MCU IC WRITER
WRITER FORTE6510/6520/6540 VER 4.0 TER语音烧录器中文使用说明书FOR TE6510/6520/6540 WRITER一、功能简介TER 系列WRITER是配合本公司所推出OTP（ONE TIME PROGRAMMABLE）型，TE6510/6520/6540VOICE ROM所开发的产品，使用程序分成两部分，一部分是语音编辑（VOICE EDIT）我们建议您使用声霸卡所提供的编缉器如VEDIT2.EXE它提供了语音录制、编辑、回音等效果，产生一个全新的音源，此外，我们也随盘也附上了另一种语音编辑软件，GOLDWAVE，它是一套功能完整强大的软件，您可以在上面进地录音、播音、调整语音速度、混音剪辑等等。
另一部分是语音烧录，我们为您提供一个完善软件环境，可以将您所编辑完成的语音，烧录至TE65---内，本烧录器操作简便，您不必为了一个语音而花费昂贵的光罩（MASK）费用，也不用做出复杂的应用线路，以及花费宝贵的时间特别去工厂定制，您可在家中自行完成语音烧录手续，使您的产品更加快捷多样的推向市场，更增加市场竞争力。
二、硬件设备要求1、IBM PC/AT/386/486/586或是兼容机（推荐486以上）2、主机内存至少4M以上（建议8M）3、VGA/SVGA显示器4、16BIT声霸卡或其兼容卡5、APLUS WRITER6、MOUSE（鼠标器）三、系统安装A、硬件安装：本烧录器一张界面卡，一个烧录器主体及一条排线所组成，请检查是否完整（另附驱动软件一套，操作说明书一份）。
1、请关闭PC的电源，以确保安装时不造成损坏。
2、打开PC机箱找到一个空闲的ISA扩展槽。
3、如果您的声卡已安装好，可跳过此步骤，否则小心将声卡插入扩展槽，并进行设置使其能在DOS及WINDOWS或WIN95下运行。
这样在使用烧录器时才不会有问题。
4、请将所附的排线一端插在IVR界面上，另一端与IVR WRITER连接，排线有方向性，当您方向相反时，无法插入排线座内。
PTZ-X20-IP全高清20倍光学放大IP PTZ V1.0 AIDA说明书
9
Web Settings
10
Web tings (CONTD)
11
Web Settings (CONTD)
12
Web Settings (CONTD)
DHCP IP address Subnet Mask Default Gateway
OFF 192.168.1.188 255.255.255.0
DEFAULT: 15
Return to previous menu
8
OSD MENU (CONTD)
QUALITY FORMAT SYSTEM
INFO RESET
2DNR 3DNR SHARPNESS CONTRAST SATURATION BRIGHTNESS WDR WDR LEVEL RETURN SIZE FRAME RATE RETURN ID BAUDRATE LANGUAGE/IDIOMA DHCP IP NET MASK GATEWAY RETURN IP ADDRESS RTSP URL F/W VERSION ARM VERSION FPGA VERSION USB VERSION FACTORY RESET USER SETTING USER RESET RETURN
DEFAULT: 0
Return to previous menu
AUTO/INDOOR/OUTDOOR/PUSH/ATW/MANUAL/SODIUM
DEFAULT: ATW
Set red gain level: 0-255 (Allows for precise tuning of the blue setting) DEFAULT: AUTO
When enabled, image noise and sharpness is reduced OFF/AUTO/0-4 optional: higher level = less image reduction happens ON/OFF optional, 0-15 level: higher level = sharper edges of image Set contrast level: 0-15: Sets the contrast level Set image saturation: 0-15: Sets the saturation level Set brightness of auto exposure: 0-15: Sets the brightness level ON/OFF: Enables better to light and dark images 1-6: Enables more control of WDR Return to previous menu 1080p/1080i/720p (default resolution: 1080 30p) 60/59.94/50/30/29.97/25/24/23.98 Return to previous menu Set VISCA control address 1-7 Set RS-232 baud rate to 2400/4800/9600/115200 Set language: ENGLISH/SPANISH IP address automatic acquisition switch: ON/OFF Set camera IP Set camera net mask Set camera gateway Return to previous menu Display the current IP address Display the current main stream RTSP URL Display the current ISP firmware version Display the current ARM firmware version Display the current FPGA firmware version Display the current USB firmware version Reset whole camera to factory parameters Save current parameters for User Reset use Recalls the saved user settings Return to previous menu
Sensata Technologies RP Series 热电阻器说明书
RP SERIESThermal Protectors IntroductionThe RP Series thermal protector is suited for recessed lighting applications. The RP’s compact package is designed to mount on the fixture; and, with sensitivity to changes in thermal conditions, detect the presence of insulation.With a history of more than 95 years, Sensata Technologies is a leading supplier of sensors and switches.FeaturesBenefits• Wide variety of UL recognized types • Automatic resetting device• Device causes fixture light to blink in fault condition • Sensitivity to thermal conditions • 50/60 Hz• Capable of accommodating most recessed lighting fixtures• Compact design allows for easy placement within the lighting fixtureSensata Technologies’ RP Series of thermal protectors are designed to meet UL, CSA and NEC requirements for the protection of non-IC recessed lighting fixtures. This RP thermal protector is an automatic resetting device that causes the lamp to blink during fault conditions. The RP is controlled by Sensata Technologies’ SB600 Series of protectors, which are recognized by UL for tungsten and inductive loads (File E28135) and by CSA for inductive loads (File LR20529).Sensata Technologies is an ISO and TS registered company providing world class quality products.Wiring of RP Thermal ProtectorsSPECIFICATIONS AND CHARACTERISTICS Electrical and Physical CharacteristicsType RP-1B RP-4A RP-5A RP-6A RP-7A RP-8A RP-9A RP-10A RP-11A RP-12A RP-13A RP-14A RP-15A RP-16A RP-17A RP-18AHeater 120V 277V 120V 240V 208V 120V 12V 220V 120V 277V 120V 240V 208V 12V 220V 277VNo. of Leads3343433343334334Lead Colors Bk, Wh, B l Bk, Wh, Red Bk, Wh, Bl, Red Bk, Wh, Grey Bk, Wh, Bl, Yell Bk, Wh, O r Bk, Wh, Y ell Bk, Wh, V iol Bk, Wh, Bl, O r Bk, Wh, Red Bk, Wh, B l Bk, Wh, Grey Bk, Wh, Bl, Yell Bk, Wh, Y ell Bk, Wh, Viol Bk, Wh, Bl, O rHeater Wires Bl & Wh Red & Wh Red & Wh Gray & W h Yell & Wh Or & Wh Yell & Wh Vi ol & Wh Or & Wh Red & Wh Bl & Wh Gray & W h Yell & Wh Yell & Wh Vi ol & Wh Or & WhProtector Wires Bk & Bl Bk & Red Bk & Bl Bk & Gray Bk & Bl Bk & Or Bk & Yell Bk & V iol Bk & Bl Bk & Red Bk & Bl Bk & Gray Bk & Bl Bk & Yell Bk & V iol Bk & BlStandard Pack 500500400500400500500500400500500500400500500500Sensitivity Low Low Low Low Low Low Low Low High High High HighHigh High High HighThe following instructions will assist in the proper installation of Sensata’s RP Series of thermal protectors.3 Wire RP for Dedicated VoltageThe black lead wire is always connected to the input live wire. The white wire is the common which is permanently connected at the factory with an extra six inch piece of wire of the same color. The third wire of the RP is permanently connected to the live side of the load.4 Wire RP for Multi-tap BallastsThe black lead wire is always connected to the input live wire. The white wire is the common which is permanently connected at the factory with all common wires. The red wire of the RP-5A or the orange wire of the RP-11A is connected to the 120 Volt tap of the ballast. The yellow wire of the RP-7A or RP-15A is connected to the 208 Volt tap of the ballast. The orange lead of the RP-18A is connected to the 277 Volt tap. The blue wire is then connected to the tap of the ballast which will match the input voltage. Although the primary usage is 120/277V, the thermal protector inside of these units is rated up to 480 VAC.Applications of RP’s to Recessed FixturesU.L. Normal Test BoxFor proper testing of RP’s the following conditions should be met:1. The fixture should be tested at the rated wattage and specified voltage. For example, if the fixture is rated 120 VAC, then the output voltage should be set at 120 VAC. In order for the RP to operate properly, voltage requirements must be adhered to. A higher voltage can, in some instances, derate the RP and cause nuisance tripping.2. The thru wire temperature, if any, should be adhered to.3. Maximum temperatures allowed by the standard agencies should not be exceeded.4. The RP is not dependent on orientation. It can be placed in a vertical position.U.L. Abnormal Test BoxFor proper testing of RP’s the following conditions should be met:1. At least 1 inch of insulation should completely surround the RP.2. The RP should be located approximately two inches from the bottom of the fixture.3. Only a small amount of epoxy to hold the thermal-couple should be used on the RP.Proper UsageThe RP functions as an insulation detector, protecting against insulation. The design of the RP thermal protectors allows a specific model to protect a family of fixtures. The operation of the bimetallic device within the RP functions primarily from the biasing of its internal heater. The heater is matched to the supply voltage and generates the majority of the heat necessary to trip the device if it should be completely surrounded by 1 inch of insulation. In this manner, the RP functions as an insulation detector.For the best performance, the RP-8A thermal protector is typically used for 300 and 500 quartz lamps and 120 Volt 400 Watt HID fixtures where 90ºC thru wire is specified. As an alternative to the lower sensitivity RPs, higher sensitivity RPs are commonly used for low wattage fixtures that are listed by UL for mark spacing. This drawing represents the typical placement of these devices for maximum performance:The following information describes the fixtures’ voltage, temperature and RP placement requirements necessary to U.L. normal and abnormal tests.In addition, this information outlines requirements to be met for proper usage of Sensata’s RP thermal protectors.SpecificationsThe RP and SB600 thermal protector within the RP are recognized and tested under standard UL873 for Temperature Indicating and Regulating Equipment.The thermal protector within the RP was tested by UL for 10,000 cycles to the following values:1. 500 Watts at 120VAC with tungsten load.2. 400 Watts at 120VAC to 480VAC with an inductive load.3. 75 watts at 12VAC with tungsten load.The RP has passed tests by UL for the City of Chicago for overlamping in the normal test box and air tightness for the return plenum.The RP clip is made of spring steel and designed for a 7/8” knockout hole to fit a wall thickness of .032-.078”.GLOBAL SALES OFFICESNorth AmericaSensata Technologies, Inc. Electrical Protection529 Pleasant Street, MS B-49 Attleboro, Massachusetts 02703 Phone: 1-508-236-3287EuropeSensata Technologies Holland B.V.Jan Tinbergenstraat 807559 SP HengeloThe NetherlandsPhone: +31 74 357 8000AsiaSensata Technologies (Shanghai) Co.,Ltd.Novel Plaza, 8th Floor128 Nanjing RoadWest Huangpu DistrictShanghai 200003, PRCPhone: 86-21-23061553Central & South America Sensata Technologies Sensores e Controles Do Brasil LTDA.Rua Azarias de Melo, 648 Bairro Taquaral-Campinas/SP BrasilPhone: 19-3754-1142Middle East & IndiaSensata Technologies India Pvt. Ltd. Bagmane Tech Park Byrasandra CV Raman Nagar Bangalore-560 093IndiaPhone: 91-25-099329DIMENSIONS Dimensions are in mm (Inches)Page 6Sensata Technologies, Inc. (“Sensata”) data sheets are solely intended to assist designers (“Buyers”) who are developing systems that incorporate Sensata products (also referred to herein as “components”). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, evaluation and judgment in designing Buyer’s systems and products. Sensata data sheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular data sheet. Sensata may make corrections, enhancements, improvements and other changes to its data sheets or components without notice.Buyers are authorized to use Sensata data sheets with the Sensata component(s) identified in each particular data sheet. HOWEVER, NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATA SHEETS ARE PROVIDED “AS IS”. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATA SHEETS OR USE OF THE DATA SHEETS, EXPRESS, IMPLIED OR STATUTORY, INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD TO SENSATA DATA SHEETS OR USE THEREOF.All products are sold subject to Sensata’s terms and conditions of sale supplied at SENSATA ASSUMES NOLIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS’ PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONS-RELATED INFORMATION OR SUPPORT THAT MAY BE PROVIDED BY SENSATA.CONTACT USRevised 02/12/18Americas+1 (888) 438 2214*******************Europe, Middle East & Africa +31 (74) 357 8156temperature-info.eu @ Asia Pacific*************************.com China +86 (21) 2306 1500Japan +81 (45) 277 7117Korea +82 (31) 601 2004India +91 (80) 67920890Rest of Asia +886 (2) 27602006ext 2808AGENCY APPROVALS & CERTIFICATIONSWARNINGSRISK OF MATERIAL DAMAGE AND HOT ENCLOSURE• The product’s side panels may be hot, allow the product to cool before touching • Follow proper mounting instructions including torque values • Do not allow liquids or foreign objects to enter this productFailure to follow these instructions can result in serious injury, or equipment damage.HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARCH FLASH• Disconnect all power before installing or working with this equipment • Verify all connections and replace all covers before turning on powerFailure to follow these instructions will result in death or serious injury。
PTN基础培训
MPLS Tunnel OAM：
双向连通性监测及保护倒换：采用硬件支持对CV（Connectivity Verification）/FFD（Fast Failure Detection）/FDI（Forward Defect Indicator）/BDI（Backward Defect Indicator）消息的发送、接收和超时判断，实现快速连通性检测与失效指示； 故障检测与定位：MPLS Tunnel Ping/TraceRoute 网络性能监控： MPLS Tunnel的丢包数、丢包率、时延和抖动等；
Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.
Page 10
OAM特性介绍（续2）
PW OAM，OAM报文增加了OAM标签：
连通性检测及保护倒换：CV/FFD； 故障检测与定位：PW Ping/Traceroute； 性能监测：硬件实现对于丢包、丢包率、时延和抖动的监测。
图：PW OAM报文格式
图：MPLS OAM连通性检测
PW 不区分Ingress和Egress方向，PW OAM使能时需要同时使能OAM发送和接收功能。
一端发送检测报文，另一端端接收检测报文。
当Egress端检测到链路失效后，通过反向通道把缺陷传到Ingress端，从而实现对整个PW的监视。 PW OAM实现链路检测并触发PW APS，并可以进行性能统计，例如丢包和时延抖动。
Page 1
培训目标
学完本课程后，您应该能：
掌握MPLS特性 掌握OAM特性 了解BFD特性 了解ARP热备特性 掌握PTN接口类型 了解SNMP特性
C220 Pt Temperature Sensor 根据 DIN EN 60751说明书
C220, Pt Temperature Sensor according to DIN EN 60751Temperature range -196 °C to +150 °CThe C220 thin-film Pt-RTD provides the ideal curvecharacteristics of ceramic wire-wound RTDs with the addedbenefits of high vibration resistance and lower cost. High long-term stability, excellent thermal shock resistance and ahysteresis-free operating temperature range of -196 °C to+150 °C offer an ideal solution for chemical & pharmaceuticalprocessing, cryogenics, analytical equipment, and cold chainmonitoring.Pt100 F 0.3 (B)32207399VCI-Plastic bagThe measuring point for the nominal resistance is 8 mm from the end of the sensor body.Temperature Range of Tolerance ClassValidity of Class F 0.3 (B)-196 °C to +150 °C Temperature CoefficientTCR = 3850 ppm/KResponse TimeWater (v = 0.4 m/s):t0.5 = 0.06 st0.9 = 0.2 sAir (v = 2 m/s):t0.5 = 3 st0.9 = 13 s Measuring CurrentPt100 Ω: 0.3 to 1 mA(self-heating has to be considered)Dimensions and Tolerances in mmL: 2.3 ±0.15W1: 1.9 ±0.15H: 1.0 +0.3 -0.2LL: 10 ±1.0Lø: 0.25 ±0.02W2: 0.8 ±0.1Image for illustration purposes onlyColor, shape and forming of fixing drop may varyIdeal for cryo temperaturesExcellent long term stability and low drift High accuracy and interchangeability High thermal shock resistanceFree of hysteresisC220, Pt Temperature Sensor according to DIN EN 60751 Temperature range -196 °C to +150 °CLong-Term StabilityThe drift of the resistance value at 0 °C after a storage for 1000 hours in air at the declared upper temperature limit is not more than the tolerance value of the declared tolerance class according DIN EN 60751.Typical drift of R(0 °C) is 0.03 % after 1000 hours at +150°C.Self-Heating0.4 K/mW at 0 °CInsulation Resistance> 100 MΩ at 150 °CVibration ResistanceAt least 40 g acceleration at 10 to 2000 Hz, depends on installationShock ResistanceAt least 100 g acceleration with 8 ms half sine wave, depends on installationConnection TechnologyBrazing Lead TypeAgPdTensile Strength of Leads≥ 8 NPackagingVCI-Plastic bagAlternative packaging forms on requestStorage LifeMin. 12 months (in original packaging)NoteOther tolerances, values of resistance and wire lengths are available on request.C220 and C420 Pt elements are optimized for low-temperature use. To avoid a potential tolerance shift, the elements should not be exposed to temperatures exceeding 150 °C during storage, assembly, or use.Due to random sample measurements, a bending of connection wires may occur (called V-shape). This bending is batch-dependent and has no influence on the functionality ofthe platinum measuring resistor.The information provided in this data sheet describes certain technical characteristics of the product, but shall not be qualified or construed as quality guarantee (Beschaffenheitsgarantie) in the meaning of sections 443 and 444 German Civil Code. The information provided in this data sheet regarding measurement values (including, but not limited to, response time, long-term stability, vibration and shock resistance, insulation resistance and self-heating) are average values that have been obtained under laboratory conditions in tests of large numbers of the product. Product results or measurements achieved by customer or any other person in any production, test, or other environment may vary depending on the specific conditions of use.The customer is solely responsible to determine whether the product is suited for the customer's intended use; in this respect YAGEO Nexensos cannot assume any liability. The sale of any products by YAGEO Nexensos is exclusively subject to the General Terms of Sale and Delivery of YAGEO Nexensos in their current version at the time of purchase, which is available under /tc or may be furnished upon request. This data sheet is subject to changes without prior notice.YAGEO Nexensos GmbH, Reinhard-Heraeus-Ring 23, 63801 Kleinostheim, Germany。
大字数显示器 (Model LDD) 说明书
O WIDE SELECTION OF INPUT MODULES O 3.32 INCH (84.4 mm) HIGH DIGITS O 115/230 VAC SWITCH SELECTABLE O RUGGED STEEL CONSTRUCTION O AVAILABLE IN 4 OR 6-DIGIT VERSIONSO AVAILABLE WITH RED OR GREEN LED DISPLAY O SEALED FRONT PANEL CONSTRUCTION (NEMA 4/IP65)O VERSATILE MOUNTING OPTIONSOTEMPLATE PROVIDED FOR EASY INSTALLATIONDESCRIPTIONThe Large Digit Display, Model LDD, is a versatile display which can increase your productivity by offering your plant floor or production area a visual display of their current status, such as counting, rate indication, real time,or any engineering unit required. The LDD is available in either a 4-digit or a 6-digit display version with Red or Green LED displays, that accepts a selection of personality boards to meet your specific application needs (see Personality Module Bulletins for more information).There are four panel wiring knock-outs provided, two 7/8" (22.2 mm)knock-outs and two 1/2"(12.7 mm)knock-outs. Also provided is a removeable cover located on the rear panel which will expose one open ended cut-out for easy wire installation.The LDD has a sealed front panel which meets NEMA 4/IP65 requirements for wash-down and dusty environments when properly installed. The 3.32"(84.4 mm)digits are readable to 130 feet (40 M).SAFETY SUMMARYAll safety related regulations, local codes and instructions that appear in the manual or on equipment must be observed to ensure personal safety and to prevent damage to either the instrument or equipment connected to it. If equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.SPECIFICATIONS1. DISPLAY:3.32" (84.4 mm)High, Red or Green LED display.2. POWER REQUIREMENTS:Switch selectable 115/230 V AC (±10%),50/60 Hz, 17 V A 4-digit, 21 V A 6-digit (including module).3. CONSTRUCTION:Steel construction textured with polyurethane paint for scratch and corrosion resistance protection. Front panel meets NEMA 4/IP65requirements for indoor use when properly installed. Installation Category II,Pollution Degree 2. (Panel gasket included with unit.)4. ENVIRONMENTAL CONDITIONS:Operating Temperature : SEE MODULE LITERATURE Storage Temperature : -40 to 70°COperating and Storage Humidity : 85% max. relative (non-condensing)over operating rangeAltitude : Up to 2000 metersMODELLDD - LARGE DIGIT DISPLAYSPECIFICATIONS (Cont’d) Array 5. CERTIFICATIONS AND COMPLIANCES:SAFETYIEC 61010-1, EN 61010-1: Safety requirements for electrical equipmentfor measurement, control, and laboratory use, Part 1.IP65 Enclosure rating (Face only), IEC529Type 4 Enclosure rating (Face only), UL50EMC EMISSIONS:Meets EN 50081-2: Industrial Environment.EMC IMMUNITY:Meets EN 50082-2: Industrial Environment.Refer to individual personality module specifications for aditional information.6. MOUNTING REQUIREMENTS:Max. panel thickness is 0.375" (9.5 mm).Min. panel thickness for NEMA4/IP65 sealing is 0.125" (3.2 mm).7. WEIGHT: 8 lbs (3.6 kg) (less module).Disconnect all power before installing or removing module. SET-UPTo place the personality module into the LDD, first remove the rear coverby unscrewing the two captive fasteners. Then, before installing the moduleinto the LDD, configure the module for the specific application by SETTINGALL APPLICABLE DIP SWITCHES AND JUMPERS AT THIS TIME (seeaccompanying module data sheet). Place the module on the plastic standoffs(see figure 1). Push on the four posts as shown in figure 2 until the carrier snapsinto place.Note: Power should NOT be applied until the terminal block is plugged into themodule AND the module is properly installed into the Large Digit Display. Select the proper voltage by setting the switch to either 115 or 230 volts. Connect the display and power cables on the module to the appropriate connectors on the power supply board (see figure 2).To program the Intelligent Meter, three normally open momentarypushbuttons are connected to “P”, “UP”, “DOWN”, and common of the LDD(not included with the Intelligent Meter). The Model PGM is a small plasticcase with three normally open momentary pushbuttons and 10 feet (3 M)ofshielded cable, and is well suited for programming the Intelligent Metermodule. Although, any normally open, momentary pushbutton switches can beused. (SEE APPROPRIATE MODULE LITERATURE FOR SET-UP ANDOTHER CONNECTIONS.)To remove module from the LDD, disconnect the display and power cables,then remove the carrier from the standoffs by disengaging the tabs andsimultaneously lifting the carrier. Repeat this until the module has cleared all 4standoffs.INSTALLATION ENVIRONMENTThe unit should be installed in a location that does not exceed the maximumoperating temperature and provides good air circulation. Placing the unit neardevices that generate excessive heat should be avoided.The LDD may be cleaned using alcohol compounds such as Isopropanol ormethanol. Also, liquid glass cleaners may be used if they do NOT containammonia.NOTE: MINIMAL EXPOSURE OF KETONE SOLVENTS TO THE LDD ISGOING TO CAUSE A WHITENING OF THE DISPLAY OVERLAY. Continuous exposure to direct sunlight may accelerate the aging process of the bezel.The LDD is intended to be mounted into an enclosed panel with a gasket toprovide a water-tight seal. A gasket and ten 10 to 32 kep nuts are provided foreasy installation. The recommended minimum panel thickness for NEMA4/IP65 applications is 0.125" (3.2 mm). Thinner panels may be used but maydistort and not provide a water-tight seal.For ease of installation, the cardboard template (supplied with the LDD)maybe used to mark the holes and cut-out locations on the panel. After the panelcut-out has been completed and deburred, insert the unit with the panel gasket,into the panel as depicted in the drawing (see figure 3). Install the ten kep nutsand tighten evenly for uniform gasket compression.By using additional hardware, the LDD can be surface-wall mounted,suspended, or bottom mounted. To surface-wall mount the unit, two sets ofMB6 brackets are required. To suspend or bottom mount the unit, one set ofMB6 brackets is required.1. TOTALIZER2. LINEARIZER 4-20 mA MODEL NO.DESCRIPTION+18 VDC 3. PEAK/VALLEYDUAL SERIAL ANALOG PART NUMBEREXCITATION 4. TARE ALARM OUTPUTOUTPUT5. E2-CON6. EFFICIENCYIntelligent Meter Modules NO NO NO NO NO PBD10000For Decade Voltage Inputs *YES NO NO NO NO PBD10100PBD1YES NO YES NO NO PBD10102(See IMD1 Bulletin for operating YES 1, 2, 3, 4, 5NO NO NO PBD13100Specifications.)YES 1, 2, 3, 4, 5YES YES YES PBD13107Intelligent Meter Modules NO NO NO NO NO PBD20000For Decade Current Input *YES NO NO NO NO PBD20100PBD2YES NO YES NO NO PBD20102(See IMD2 Bulletin for operating YES 1, 2, 3, 4, 5NO NO NO PBD23100Specifications.)YES 1, 2, 3, 4, 5YES YES YES PBD23107Intelligent Serial Slave Display Module *20 mA SRC 3, 5NO YES NO PBA04101PBA(See IMA Bulletin for operating 20 mA SRC 3, 5YES YES NO PBA04104Specifications.)20 mA SRC 3, 5YES YES YES PBA04107+12 VDC 1, 2, 3, 5, 6NO NO NO PBI04100Intelligent Digital Rate Meter *+12 VDC 1, 2, 3, 5, 6NO YES NO PBI04101PBI(See IMI Bulletin for operating +12 VDC 1, 2, 3, 5, 6YES NO NO PBI04102Specifications.)+12 VDC 1, 2, 3, 5, 6NO NO YES PBI04103+12 VDC 1, 2, 3, 5, 6YES YES YESPBI04107PGMProgramming BoxPGM00000* Note: All the above Intelligent Meter modules require a 6-digit Large Digit Display, Model LDD00600 or LDD0G600.ORDERING INFORMATION FOR APOLLO INTELLIGENT METER MODULESORDERING INFORMATIONFOR APOLLO PERSONALITY MODULESPERSONALITY MODULESThe following Apollo and IM capabilities are available as modules for the TROUBLESHOOTINGFor further technical assistance, contact technical support at the appropriate company numbers listed.LIMITED WARRANTYThe Company warrants the products it manufactures against defects in materials and workmanship for a period limited to two years from the date of shipment, provided the products have been stored, handled, installed, and used under proper conditions. The Company’s liability under this limited warranty shall extend only to the repair or replacement of a defective product, at The Company’s option. The Company disclaims all liability for any affirmation, promise or representation with respect to the products.The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against damages, claims, and expenses arising out of subsequent sales of RLC products or products containing components manufactured by RLC and based upon personal injuries, deaths, property damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be to any extent liable, including without limitation penalties imposed by the Consumer Product Safety Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty Act (P.L. 93-637), as now in effect or as amended hereafter.No warranties expressed or implied are created with respect to The Company’s products except those expressly contained herein. The Customer acknowledges the disclaimers and limitations contained herein and relies on no other warranties or affirmations.。
Panasonic高清摄像头产品说明书
• 720p HD images up to 30 fps• Super high resolution at HD / 1,280 x 720 created by 2.4 Megapixel high sensitivity MOS image sensor• Multiple H.264 (High profile) streams and JPEG streams ensure simultaneous real time monitoring and high resolution recording by “UniPhier ®”, Panasonic’s proprietary System LSI platform.• Full frame (Up to 30 fps) transmission at 1,280 x 960 image size • 45x HD extra optical zoom at 1,280 x 720 (30x optical zoom) 90x extra optical zoom at 640x360 resolution with 12x digital zoom enabling 1080x zoom.• Super Dynamic and ABS (Adaptive Black Stretch) technologies deliver 128x wider dynamic range compared to conventional cameras.• Face Super Dynamic technology ensures clear face image.• High sensitivity with Day/Night (ICR*) function: 0.3 lx (Color), 0.04 lx (B/W) at F1.6 *ICR: IR Cut filter Removal• VIQS (Variable Image Quality on Specified area) technology allows the designated 2 areas to retain higher image quality while the excluded area will have a decreased image quality, which enables to use lower image file size and bit rate.VIQS can be set on preset position (1 to 8) and except preset.• Digital Noise Reduction: 3D-DNR ensures noise reduction in various conditions.• Progressive scan ensures clear images with less motion blur and no tearing even when the subject is moving.• Electronic sensitivity enhancement: Auto (Up to 16x) / OFF • Selectable light control modes:Outdoor scene / Indoor scene (50 Hz) / Indoor scene (60 Hz) / Fix shutter Indoor scene (50 Hz / 60 Hz): Flicker causedby fluorescent lightning will be automatically compensated.• 360 degrees endless Panning• Advanced auto tracking: The camera automatically pans and tilts to follow a moving subject and keep it in the center of the image.• PTZ control can be taken very smoothly on the user friendly GUI with 16 speeds pan/tilt and “Drag and Zoom” operation enabling finer control. 256 speeds available for system with WV-CU950 system controller.• Up to 256 preset positions• 360 map shot: 8 thumbnail images at 45 deg. intervals make it simple to direct the camera easily by clicking on a thumbnail.• Industrial grade Pan / Tilt / Zoom mechanism for high reliability• VMD (Video Motion Detection) with 4 programmable detection areas, 15 steps sensitivity level and 10 steps detection size• Privacy Zone can mask up to 32 private areas, such as house windows and entrances/exits.• Camera title display: Up to 20 alphanumeric characters on the browser• Alarm sources including 3 terminal input, VMD and Panasonic alarm command can trigger actions such as SDXC/SDHC/SD memory recording, FTP image transfer, E-mail notification, Indication on browser, Alarm terminal output, and Panasonic alarm protocol output.• Full duplex bi-directional audio allows interactive communication between camera site and monitoring site.• JPEG Image compression ratio can be changed by alarm so that higher quality image can be provided.• Prioritized stream control: One of the video streams can be prioritized when multiple recorders or client PCs are accessing the camera so that the recorder or the client PC can maintain the frame rate.• SDXC/SDHC/SD Memory card slot for manual recording (H.264 / JPEG), alarm recording (H.264 / JPEG) and backup upon network failure (H.264 / JPEG) • H.264 max. bit rate / client and Total bit rate control allows flexible network traffic management. Frame rate priority mode controls bit rate and compression ratio to provide the specified frame rate.• Internet mode: H.264 images can be transmitted over HTTP protocol.• Multi-language: English / Italian / French / German / Spanish / Portuguese / Russian / Chinese / Japanese • IPv4/IPv6 protocol supported• Supports SSL, DDNS (viewnetcam, RFC2136)• Still images (JPEG) can be viewed on mobile phones via Internet.• Onvif compliant model• IP66 rated water and dust resistant. Compatible with IEC60529 measurement standard compliant.• Dehumidification device for use in various weather conditions • Rain wash coating dome cover• Ambient Operating Temperature : -50 °C to +55 °C ( -58 °F to 131 °F )• Fog compensation function equipped as standard.• AEM (Auto Eyelid Mechanism) offers images that are more natural and easy to watch reducing doubled images when direction of the lens moved above the horizontal.HD / 1,280 x 720 H.264 Weather Proof Camera featuring 45x HD extra optical zoom and Super DynamicKey FeaturesSuper Dynamic Weather Resistant HD PTZ Dome Network CameraWV-SW397A(Rain Wash Coating Model)Trademarks and registered trademarks– Microsoft, and Windows are registered trademarks of Microsoft Corporation in the U.S. and other countries.– iPad, iPhone and iPod touch are registered trademarks of Apple Inc.– Android is a trademark of Google Inc.– UniPhier is a registered trademark of Panasonic Corporation.– "MEGA Super Dynamic", "i-PRO SmartHD" logos are trademarks or registered trademarks of Panasonic Corporation.– ONVIF and the ONVIF logo are trademarks of ONVIF Inc.Important– Safety Precaution: Carefully read the Important Information, Installation Guide and operating instructions before using this product.– Panasonic cannot be responsible for the performance of the network and/or other manufacturers' products used on the network.• Masses and dimensions are approximate. • Specifications are subject to change without notice.SpecificationsSDXC/SDHC/SDMemory Card (Option)Cellular Phone Compatibility Mobile Terminal Compatibility Alarm Source Alarm ActionsAlarm LogScheduleH.264 recording (Audio recording is enable): Manual REC / Alarm REC (Pre/Post) /Schedule REC / Backup upon network failure JPEG recording: Manual REC / Alarm REC (Pre/Post) / Backup upon network failureCompatible SD (SDHC/SDXC) card: Panasonic2 GB, 4 GB*, 8 GB*, 16 GB*, 32 GB*, 64GB** model *SDHC card, ** SDXC card (except miniSD card and microSD card) JPEG image, panning/ tilting/ zoom/ focus control, AUX control (by access level)iPad, iPhone, iPod touch (iOS 4.2.1 or later) Android mobile terminals3 terminals input, VMD, Command alarm, Audio detection SDXC/SDHC/SD memory recording, E-mail notification,Indication on browser, FTP image transfer, Panasonic protocol output With SDXC / SDHC / SD memory card: 5,000 logs, without SDXC / SDHC / SD memory card: 1,000 logsAlarm / VMD / Access permission / H.264 recording / Audio detection Monitor Output (for adjustment) Microphone/Line InputAudio OutputExternal I/O Terminals Safety/EMC StandardPower Source and Power Consumption Ambient Operating TemperatureAmbient Operating Humidity Shock ResistanceWater and Dust Resistance DimensionsMass (approx.) FinishVBS : 1.0V[p-p] / 75Ω,NTSC / PAL composite, BNC JackMIC IN and Line IN are selectable. ø3.5 mm stereo mini jack (monaural input) (Applicable microphone: Plug-in power type) Supply voltage: 2.5 V ±0.5 V Input impedance: approx. 2 kΩ ø3.5 mm stereo mini jack (monaural output) Line levelALARM IN 1 (DAY/NIGHT IN), ALARM IN 2 (ALARM OUT), ALARM IN 3 (AUX OUT) AC24 V : 3.5 A, 55 WPoE+ DC54 V: 470 mA, 25 W (IEEE802.3at compliant)POE Injector (60 W) DC54 V : 1.0 A, 50 WAC24 V and Tested PoE Injector (60 W) : –50 °C to +55 °C (-58 °F to 131 °F) * with limitations POE+ : –30°C to +55°C (–22 °F to 131 °F) Less than 90 % (no condensation)Compliant with IK10 (IEC62262)Main body : IP66 (IEC60529) compliantø229 mm x 392 mm(H) {ø9-1/32 inches x 15-7/16 inches(H)} diameter of the dome 160 mm(6-5/16 inches) Approx. 5.0 kg { 11.02 lbs}Main body : Aluminum die cast, Natural silver Sunshields : ASA resin coating, Natural silverDome section : Clear polycarbonate resin (Rain wash coating)<Safety>UL (UL60950-1), C-UL (CAN/CSA C22.2 No.60950-1), CE, IEC60950-1<EMC>FCC Part15 Class A, ICES-003 Class A, EN55022 Class B, EN55024*1 Converted value*2 For further information about PC system requirements and precautions for when using Microsoft ® Windows ® 8.1,Microsoft ® Windows ® 8, Microsoft ® Windows ® 7, Microsoft ® Windows Vista ®, or Windows Internet Explorer, click“Manual” - “Open” from the supplied CD-ROM and refer to “Notes on Windows ® / Internet Explorer ® versions”.*3 AAC (Advanced Audio Coding) is only used when recording audio on an SD memory card.*4 Transmission for 2 streams can be individually set.NetworkAlarmInput/OutputGeneralImage Sensor Effective Pixels Scanning Mode Scanning AreaMinimum IlluminationWhite BalanceLight Control ModeShutter SpeedSuper DynamicFace Super Dynamic Adaptive Black Stretch Fog compensation Gain (AGC)Electronic Sensitivity UP Day & Night (ICR)Digital Noise Reduction Video Motion Detection Privacy Zone Image Stabilizer VIQSDouble Image Reduction Camera Title (OSD) Focus distance Focal Length Zoom RatioDigital (Electrical) Zoom Angular Field of ViewMaximum Aperture Ratio Focusing Range Aperture RangePanning RangePanning SpeedTilting RangeTilting SpeedProportional Pan/Tilt Control Number of Preset Positions Auto Mode Image HoldPTZ Position Display Self Return Map Shot4.3 mm - 129.0 mm {3/16 inches - 5-3/32 inches} 30x / 45x with HD extra optical zoom (at 1280 x 720)12x (Max. 1080x combined with extra optical zoom at 640 x 360) H: 2.6° (TELE) - 64.6° (WIDE), V: 1.6° (TELE) - 38.2° (WIDE) ([16:9] mode)*H: 1.4° (TELE) - 44.4° (WIDE), V: 1.1° (TELE) - 33.8° (WIDE) ([4:3]mode)1 : 1.6 (WIDE) - 4.7 (TELE) 2.0 m - ∞ F1.6 - Close 360° endlessManual: approx. 0.065°/s to 120°/s, Up to 256 steps (depending on the controller)Preset : up to approx. 300°/s–15° to 195° (upward-level-downward)Auto Eyelid Mechanism (Double image reduction)Selectable tilting angle: 0° / –5°/ –10° / –15Manual: approx. 0.065°/s to 120°/s, Preset: up to approx. 300°/s Yes 256Auto track/ Auto pan/ Preset sequence/ 360 map-shot/ Patrol On / Off On / Off10 s / 20 s / 30 s / 1 min / 2 min / 3 min / 5 min / 10 min / 20 min / 30 min / 60 min 360° map shot / Preset map shotCamera ControlDisplay ModeCamera Title Clock Display Alarm Control One Shot Capture AudioSD Memory Data Download GUI/Setup Menu LanguageSystem Log Supported OS *2Supported BrowserImage Resolution H.264 *4JPEGImage Capture Mode:16:9H.264 : 1,280 x 720 / 640 x 360 / 320 x 180, up to 30 fps JPEG (MJPEG): 1,280 x 720 / 640 x 360 / 320 x 180, up to 30 fps 10Base-T / 100Base-TX, RJ45 connectorH.264 : 1,280 x 960 / 800 x 600 / 640 x 480 / 320 x 240, up to 30 fps JPEG (MJPEG): 1,280 x 960 / 800 x 600 / 640 x 480 / 320 x 240, up to 30 fps Network IF Audio Compression Audio ModeAuthentication for Audio Total Bit RateSupported ProtocolFTP ClientMaximum concurrent access numberPan/Tilt (256 steps), Zoom, Focus, Click centering, Drag zoom, Iris,Preset position call and program, Auto modeSpot, Quad: Image from 16 cameras can be displayed in 4 different Quad screens or 16 split screen (JPEG only). 20 characters camera title available.Up to 20 alphanumeric charactersTime: 12H/24H, Date: 5 formats on the browser, Summer time (Manual)ResetA still picture will be displayed on a newly opened window.Mic (Line) Input: On / Off Volume adjustment : Low / Middle / High Audio Output : On / Off Volume adjustment : Low / Middle / High Still or motion Images recorded in the SDXC/SDHC/SD memory card can be downloaded. English / Italian / French / German / Spanish / Portuguese / Russian / Chinese / Japanese Up to 100 (Internal)Up to 4,000 (SDXC/SDHC/SD memory when the recording format is set to JPEG.) error logs Microsoft ® Windows ® 8.1,Microsoft ® Windows ® 8, Microsoft ® Windows ® 7, Microsoft ® Windows Vista ®, Microsoft ® Windows ® XP SP3Windows ® Internet Explorer ® 11 (32 bit), Windows ® Internet Explorer ® 10 (32 bit), Windows ® Internet Explorer ® 9 (32 bit), Windows ® Internet Explorer ® 8(32 bit),Windows ® Internet Explorer ® 7 (32 bi t)Approx.1/3 type MOS image sensor Approx. 2.4 mega pixels Progressive scan5.38 mm (H ) x 3.02 mm (V ) {7/32 inches(H) x 1/8 inches(V)}Color: 0.3 lx, BW: 0.04 lx (F1.6, Auto slow shutter: Off (1/30s), Gain: On(High))Color: 0.019 lx, BW: 0.003 lx (F1.6, Auto slow shutter: Max. 16/30s, Gain: On(High)) *1AWC (2,000 - 10,000 K), ATW1 (2,700 - 6,000 K), ATW2 (2,000 - 6,000 K)Outdoor scene: Automatic integration of ALC and ELCIndoor scene [50 Hz]: Automatic integration of ALC and ELC (up to 1/100 s)Indoor scene [60 Hz]: Automatic integration of ALC and ELC (up to 1/120 s)Fix shutterFix shutter: 1/30, 3/100, 3/120, 2/100, 2/120, 1/100, 1/120, 1/250,1/500, 1/1,000, 1/2,000, 1/4,000, 1/10,000 (only at Super Dynamic Off) On / OffOn / Off (Only when Super Dynamic: On) On / Off (Only when Super Dynamic: Off) On / OffOn (Low, Mid, High) / OffOFF / AUTO (Max. 2x (2/30 s), 4x (4/30 s), 6x (6/30 s), 10x (10/30 s), 16x (16/30 s)) Mode: AUTO1 / AUTO2 / AUTO3 / On / Off, Level: High / Low, with external control High / Low4 areas, Sensitivity: 15 steps, Detection size: 10 steps Up to 8 zones / Up to 32 zones, Gray / Mosaic On / OffUp to 2 zones at preset position 1-8 and except preset On / OffUp to 20 characters (alphanumeric characters, marks) Limited / UnlimitedImage Capture Mode:4:3Transmission Mode Frame Rate Bit Rate/ClientImage Quality Refresh Interval Transmission Type Image Quality Refresh Interval Transmission TypeConstant bitrate / Frame rate priority / Best effort /Advanced VBR 1 / 3 / 5 / 7.5 / 10 / 12 / 15 / 20 / 30 fps64 / 128 / 256 / 384 / 512 / 768 / 1,024 / 1,536 / 2,048 / 3,072 / 4,096 / 6,144 / 8,192 kbps Low / Normal / Fine0.2 / 0.25 / 0.33 / 0.5 / 1 / 2 / 3 / 4 / 5 s Unicast / Multicast 10 steps0.1 fps to 30 fps Pull / PushG.726 (ADPCM) 32 kbps / 16 kbps, G.711 64 kbps, AAC *3Off / Mic (Line) input / Audio output / Interactive (Half duplex) / Interactive (Full duplex) Level 1 only / Level 2 higher / All users64 / 128 / 256 / 384 / 512 / 768 / 1,024 / 2,048 / 4,096 / 8,192 kbps / Unlimited IPv6: TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP, SMTP, DNS, NTP, SNMP, DHCPv6, ICMP, ARPIPv4: TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP,FTP, SMTP, DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP, ICMP, ARP Alarm image transmission, FTP periodic transmission (When the FTP transmission is failed, backup on an optional SDXC/SDHC/SD memory card is available. ) Up to 14 users (Depends on network conditions)CameraLensPan and Tilt Browser GUINetworkDISTRIBUTED BY:/PanasonicNetworkCamera(2A-146AL)。
电源设备说明书
Steps to size a Power Supply1. Determine the "Average" continuous current of the load and the typical inrush current.2. Select a power supply where the rated load is at/or below the current of the device and the Peak Current is less than the short-circuit rating of thepower supply.Notes:ReservePower will deliver up to 25% additional current continuously. PowerBoost will deliver 150% of rated current for up to 5 s.Example:Application: Single Phase 120V input, 24V output, 5A continuous current with 7.5A inrush currentSolution: 1606-XLS120E8Output CurrentOutputVoltageI RA TED: 5 AI SHORT CIRCUIT: >9 AI POWER BOOST: 7.5 ASelection InformationPower SuppliesHow to Select a Bulletin 1606 Power SupplyThe Bulletin 1606 line of Power Supplies is designed with "reserve power" thereby eliminating the need to oversize your power supply to start high inrush loads.Output Characteristic for XLS120E (5 A) Power Supply1Not all features apply to all power supplies; see individual power supply descriptions for specificsA more detailed list of performance specifications can be found at the Allen-Bradley web site/industrialcontrols/products/power_supplies/index.html8Quick Guide/ Special ApplicationsPower SuppliesSpecial ApplicationsQuick GuideBulletin 1606-(number from table) Power Supply Quick GuideExample: For a 24...28 Volt, 3-Phase, 120 Watt power supply, the Cat. No.would be 1606-XL120E-3. 1Cat. No. 1606-XLS240K does not have Hazardeous Location Rating.1606–XLS480E–3abcde8Catalog Number Explanation/Product SelectionNote:Special output signals are onlyavailable with the 960 W power supply.Catalog Number ExplanationProduct Selection1606-XLS Performance ⎯Single- and Three-Phase Single-PhaseImportant : The following cat. no. breakdown is for explanation purposes only. It is not a product configurator. Not all combinations of fields are valid product cat. nos. First, select the desired power supply using the Product Selection tables. Then, use this breakdown for verification and explanation only.♣Unit has internal (not accessible/replaceable) input fuse. Additional protection is not required if used on branch circuits ≤UL test levels.Specifications/Approximate Dimensions811) = CE, 2) = UL 508 (cULus LISTED), 3) = UL 1950 (cURus), 4) = CSA C22.2, No. 60950, 5) Safety standards = IEC/EN 60950, EN 50178, 6) EMC standards =EN 55011 (Class B), EN 55022 (Class B), EN 61000-6-2, 7) EMC standards = EN 61000-3-2 (A14), EN 50081-1, 8) ATEX, 9) ABS/GL/RINA (Marine)♣MTBF determined by Siemens norm SN 29500 at full load current and 40 °CBulletin 1606-XLS11) = CE, 2) = UL 508 (cULus LISTED), 3) = UL 1950 (cURus), 4) = CSA C22.2, No. 60950, 5) Safety standards = IEC/EN 60950, EN 50178, 6) EMC standards =EN 55011 (Class B), EN 55022 (Class B), EN 61000-6-2, 7) EMC standards = EN 61000-3-2 (A14), EN 50081-1, 8) ATEX, 9) GL/ABS ♣MTBF determined by Siemens norm SN 29500 at full load current and 40 °C, 8) ATEX Indicates ATEX ratingIndicates conformal coatingApproximate Dimensions8mmA B C 1606-XLS80E 32 4.8 22.5 1606-XLS120E 40 5.3 29.5 1606-XLS240E 60 5.8 48.5 1606-XLS480E-3 65 6.3 401606-XLSRED32 4.8 22.5Cat. No. 1606-XLC, Back of Panel Mounting BracketFor use with Bulletin 1606-XLE and -XLS Power Supplies 20 A and above.Cat. No. 1606-XLB, Back of Panel Mounting BracketFor use with Bulletin 1606-XLE and -XLS Power Supplies below 20 A.Approximate DimensionsApproximate dimensions are shown in millimeters (in.) unless otherwise indicated. Dimensions are not to be used for manufacturing purposes.。
Braun ThermoScan 5 使用说明书
Sensata Technologies P255 铬锰钢压力传感器说明说明书
| P255Stainless Steel Pressure Transducer DescriptionFeatures• Dry Media *1• Superior Long Term Stability• Excellent Repeatability/Hysteresis • Superior EMI/RFI Rejection • Low Power Consumption • Linear Output• Temperature Compensated• Over-Voltage, Reverse Polarity & Short Circuit Protection • Ten Million Cycle Life Expectancy• Outstanding Shock & Vibration Performance1. For wet conductive media please contact usThe model P255 is based on Kavlico’s fieldproven ceramic capacitive technology with the latest state-of-the-art ASIC. Featuring a 316SS housing, the P255 is designed for general use wherever a rugged and reliable pressure transducer is required. The P255 package has a built-in Metri-Pack 150, electrical connector and supports popular process connection threads. The P255 is offered with a variety of seal materials and is suitable for many diverse applications. Specifically intended for OEM applications, the P255 delivers a cost effective solution without compromising performance orreliability.Applications• Steam Sterilizers• Gasoline & Diesel Engines • Natural Gas & CNG Engines • Agricultural Chemical Equipment • Level Measurement • Test Equipment • Injection Molding • Coolant Pressure• Industrial CompressorsPressure Ranges Electrical Connection Pressure Connection Housing Material Output SignalMAIN FEATURES1. for more options see how to orderTECHNICAL SPECIFICATIONSPressure RangesPhysicalPerformance2. for more details see Ordering Options3. Including non-linearity, hysteresis, non-repeatability, zero point and full scale error (corresponds to error of measurement per IEC 61298-2). Adjusted in vertical mounting position with pressure port downElectrical4. for min. 3 intervals at 5 minutes each5. for min. 10 seconds on assigned pinsDIMENSIONS Dimensions in mm [Inch]Page 5CONTACT USAmericas+1 (800) 350 2727***************************************Europe, Middle East & Africa +359 (2) 809 1826****************************Asia Pacific*************************.com China +86 (21) 2306 1500Japan +81 (45) 277 7117Korea +82 (31) 601 2004India +91 (80) 67920890Rest of Asia +886 (2) 27602006 ext 2808Sensata Technologies, Inc. (“Sensata”) data sheets are solely intended to assist designers (“Buyers”) who are developing systems that incorporate Sensata products (also referred to herein as “components”). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, evaluation and judgment in designing Buyer’s systems and products. Sensata data sheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular data sheet. Sensata may make corrections, enhancements, improvements and other changes to its data sheets or components without notice.Buyers are authorized to use Sensata data sheets with the Sensata component(s) identified in each particular data sheet. HOWEVER, NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATA SHEETS ARE PROVIDED “AS IS”. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATA SHEETS OR USE OF THE DATA SHEETS, EXPRESS, IMPLIED OR STATUTORY, INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD TO SENSATA DATA SHEETS OR USE THEREOF.All products are sold subject to Sensata’s terms and conditions of sale supplied at SENSATA ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS’ PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONS-RELATED INFORMATION Revised 2/7/18ORDERING OPTIONSP255Sensor, 0 - 15 PSI, Nitrile Seal Material, 1/4 - 18 NPT Pressure Connection with Mating ConnectorA: Packard with Mating Connector C: Packard without Mating ConnectorAGENCY APPROVALS & CERTIFICATIONS2011/65/EU ROHS Directive。
主流灭菌器验证探头,高精度无线温度记录仪的一点使用体会
主流灭菌器验证探头，高精度无线温度记录仪的一点使用体会本人从事热工方面的计量工作多年，用过不少品牌的无线温度验证探头，就自己这几年来对各品牌的使用情况做一个简单的总结，希望对后来者有点帮助。
德国ebro:比较早进入国内计量系统，精度及长稳性能不错，单位10年买过一批用了两三年只有个别坏掉的，印象很好；13年又买了一批8个探头，有两个在第一年出现问题，第二年又有三四个出现问题，可能是价格竞争的原因，感觉后面买的产品质量不如从前了。
德国ebro的电池比较耐用，缺点是不能现场更换电池，必须寄给售后更换；另外在热响应速度方面用的是3mm的PT1000，响应偏慢了一些；探头上部分是不锈钢，下部分是塑料的，直径应该在38mm左右吧，个头比较大，圆饼形状；美国GE:单位偶尔有用户送来标定，顺便也了解学习了一下；全不锈钢很厚重的感觉，直径应该在34mm左右，确实有点重了；外观的金属质感非常好，也是采用3mm的探针，读数器有单座还有八座两款，八座的读数器比较笨重，外出很不方便；另外在查找探头的速度上反应比较慢，可能是支持多读数器串联查找的原因；测试过一些用户送来的探头，有的使用一年左右了，精度还是不错的；至于更长时间使用的稳定性就不知道了。
但是GE的品牌应该不会差到哪去；美国Datatrace:应该是单位最早期购买的一批无线温度验证探头，大概是08年左右吧，第一次见到外观那么精致小巧探头，给人一种爱不释手的感觉；特别是Micro型，用纽扣电池的，特别小巧，换电池也很方便；但是好看归好看，用了一年左右8个探头坏掉了7个，拆开之后分析应该是密封性设计得不好，密封条太薄太小，换电池的频率高的话很容易导致密封性能下降。
Datatrace的Micro型电池特别不耐用，几乎一个月左右就要换一次；丹麦ellab:单位是在12年左右购入12个，价格应该是进口品牌里面最便宜的了；直径在25mm左右，比Datatrace大，但比GE ebro的都要小；可以自己换电池，长效电池型大概用七八个月就要换电池，比德国ebro耗电很多，软件用得也比较顺手；采用三层内外防水圈的方式，防水效果应该是最好的，探针是2mm的PT1000，热响应速度比ebro还有GE都要快很多；虽然热工计量部门对热响应速度要求不是很高，但是一些药厂对这个还是有要求的，因此看到药厂送检ellab的探头比较多；第一年有几个经常在读数的时候无法通讯，过一会有可能好；另外由于ellab的功耗偏大，换电池时要经常插拔内部的电池模块，对插排针又很脆弱；用了一年多已经有4个探头坏了，快到两年的时候一共坏了7个探头；法国TMI:有试用过一段时间，特点就是体积超小，做工很一般，如果不是看到体积那么小我们以为是国产的，换电池不大方便，电池很特别，应该是用高温纽扣电池厂家自己做二次封装的；精度基本在0.1℃范围内；另外TMI的读数器比较特别，像蜘蛛一样长出很对根对插头与探头对插，这样每个探头上都有对插孔，我们用油槽验证过后要清洁一下对插孔里的残油才能通讯，这点不太好；TMI针对各种温度段的探头用的是不同规格的电池；因为只试用过不到两个月，我们也不知道长稳如何，有的药厂购买比较多，跟我们反应是40个里面第一年有5个出现问题，这个比例质量还不算过分；国产瑞艾特:试用过4个月左右，送过来5个探头，有一个在一个月后无法通讯，另外4个没出现什么问题；精度也还行，有2个探头超出0.1℃一点点，另外的精度基本都在0.1℃以内；瑞艾特用的是3mm的PT100，采样功耗应该是比较大的，热响应也比较慢；比起国外品牌，软件界面不是很友好，应该是模仿Datatrace的软件风格；在外形及密封圈设计上也模仿了Datatrace 的风格，很薄很薄的密封垫，估计用久跟Datatrace一样会进水；另外探头整体尺寸也偏大偏长了些；国产迪威谱:试用过5个月左右，出厂精度很高，4个探头居然都在0.05℃以内，2mm的PT1000探针响应速度很快；体积比丹麦ellab的小，比法国TMI的大一些；整体做工不错，刚拿来时以为是进口品牌；另外密封圈很厚实，密封厚度与GE的相当；至于长稳性，使用5个月后做对比，漂移都在0.02℃以内，再长时间的漂移就不清楚了；国产哈泰克:有一些药厂或者食品厂送来检测过，个头比较小巧;外观加工很一般；用的是3mm的PT1000; 客户用了一年左右的时候来送检的，精度很糟糕，几个探头都超出了0.5℃，有个别探头误差在4℃以上，有点离谱了；估计长稳不行；国产Canneed:主要送来的用户都是食品厂或者啤酒厂的，使用最高温度才125℃，用户使用一年左右，好几个探头的误差都在2℃以上；读数器单座的类似ebro老款接触压紧试读数器一样，有点不方便；总结：因为长时间在高温高压或者高湿度的环境下工作，不管是进口品牌还是国产品牌，感觉都是一种消耗品，再好再贵的品牌也很难保证使用超过两年完全不出问题；对于一个长期使用无线验证探头的热工来说，肯定是希望有又耐用又便宜的产品出现，希望市场竞争越来越激烈，给我们带来更多的选择。
TEKPROBE BNC接口适用于P6204、P6205、P6217和P6231s激活FET探头的产
• Powers up to Two Probes
• For Use with: - 11000 Series Probes on NonTEKPROBETM Interfaced Scopes - P6203, P6204, P6205, P6217, P6231, P6245
• Overload Protected
Teldronix Distributor (see pages 59(}595).
Product(s) avalla~le through your local Tektronix representative (listed In the bac~ of this catalog) or call 1-800-426-2200.
.(809001
.NXillSIifl:I"',*~~
Tektronix M!lll$llf6ll1eRt products are m~ufaClureQ IR
ISO registered facilities.
P6205
• DC to 750 IVIHz • 2 pF Input C • 1 MQ Input R • Low Price
These Active Probes may also be used with 50 Q or 1 MQ oscilloscope systems, with conventional BNC interfaces, via the Tektronix 1103 TEKPROBETM Power Supply. The 1103 has dual TEKPROBpM inputs, dual BNC signal outputs, and dual voltage offset on/off switches and potentiometers.
PT6306__Natertech
DESCRIPTION
PT6306 is a 64-Bit High-Voltage Display Driver utilizing CMOS Technology specially designed for VFD display panels. It provides 64-bit bidirectional shift register, 64-bit latch and high-voltage CMOS Driver. The logic circuit operates on 5V power supply (CMOS Level Input) making it possible for PT6306 to be used in conjunction with a microcomputer. The driver block consists of 80V, 50mA (max.) high voltage output buffer. Pin assignments and application circuits are optimized for easy PCB Layout and cost saving benefits. 37, 62
HVO1 to HVO23
39 to 61
HVO24 to HVO41
O
High Voltage Output Pins
64 to 81
HVO42 to HVO64
3 to 25
LDIO
I/O
Left Data I/O Pin
28
RDIO
I/O
Right Data I/O Pin
INPUT/OUTPUT PORT CONFIGURATIONS
Sensata Technologies APL UPL系列产品说明说明书
“Existing Design-In Only”A P L /U P LINTRODUCTIONIMPORTANT NOTICE: The APL/UPL is a legacy product and no new design-in orders are being accepted. We are also discontinuing the 205 series (APL with dust proof enclosure). If the specifications for any of these products are necessary for your system, Sensata T echnologies recommends utilizing the Airpax™ IAL series.The APL/UPL magnetic circuit protector provides reliable, low-cost power switching, circuit protection and circuit control. The handle opens and closes a circuit, under normal load conditions, similar to an ON-OFF switch. Upon overload, the internal mechanism trips, opens the contacts and forcibly returns the handle to the OFF position. Since the protector is “trip free,” the internal contacts will not remain closed in the presence of an overload, even though the handle is held in the ON position.The APL/UPL line offers many configurations including series, shunt and relay with a choice of delays and ratings. APL/UPL multi-pole assemblies are available with a mix of current ratings, delays and internal circuit configurations.While designed for industrial, military and information processing applications, the APL is suitable for use in any situation where precision operation is required. Most versions of the APL family are recognized by UL per UL STD. 1077 as supplementary protectors and certified by CSA per CSA STD. C22.2–No. 235as supplementary protectors and are designated with the UPL prefix..675Note: Tolerance ± .015 [.38]unless noted. Dimensions inbrackets [ ] are millimeters.MULTI-POLE CIRCUIT PROTECTORSMulti-pole protectors are combined in an assembly with the actuating handles linked and the trip mechanisms internally coupled. A fault in either protected circuit opens all poles simultaneously. Applications include use in two-phase circuits, single-phase three-wire systems or in two or more related but electrically isolated circuits. A mix of delays, ratings and configurations is possible, with the series type having any of the auxiliary switches listed. Combinations up to nine poles are available.(SEE TABLE)“A”.75 ± .015[19.05 ± .38](TYP)ONON1.448[36.78].432[10.97]2.280[57.91].750[19.05].432[10.97]1.448[36.78]2.060[52.32]1.530[38.86]Ø 4X .156[3.96].432[10.97]1.448[36.78]Ø 2X .156[3.96].755[19.18]2.060[52.32].750[19.05].750[19.05]2.060[52.32]Ø 6X .156[3.96]One PoleTwo PoleThree PoleMounting Details Panel Mounting Tolerances: ±.005 [.13] unless noted.MULTI-POLE DIMENSIONS2 pole “A” 1.515 [38.48] max3 pole “A” 2.265 [57.53] max4 pole “A” 3.015 [76.58] max 5 pole “A” 3.765 [95.63] max6 pole “A” 4.515 [114.68] max7 pole “A” 5.265 [133.73] max8 pole “A” 6.015 [152.78] max9 pole “A”6.765 [171.83] maxNote: Dimension “A” varies with # of polesA P L /U P LSeries TripThe most popular configuration for magnetic protectors is the series trip where the sensing coil and contacts are in series with the load being protected. The handle position conveniently indicates circuit status. In addition to providing conventional over-current protection, it’s simultaneously used as an on-off switch.Auxiliary Switch(Applies to Series Trip Only)This is furnished as an integral part of a series pole in single or multi-pole assemblies. Isolated electrically from the protector’s circuit, the switch works in unison with the power contacts and provides indication at a remote location of the protector’s on-off status.Auxiliary switch contacts actuate simultaneously with the main breaker contacts, and will open regardless of whether the breaker contacts are opened manually or electrically. For auxiliary switch ratings below 6Vac or 5Vdc, an auxiliary switch with gold contacts is available. Gold contacts are not recommended for load current above 100 milliamps.The contacts on our optional RS auxiliary switch will open only in the event of an electrical trip of the circuit breaker.Shunt TripThe shunt trip is designed for controlling two separate loads with one assembly. The control is established by providing overload protection for the critical load. When the current through this load becomes excessive and reaches the trip point, the protector will open and remove power from both loads simultaneously. The total current rating of both loads must not exceed the maximum contact rating.Relay TripThis permits the overload sensing coil to be placed in a circuit which is electrically isolated from the trip contacts. The coil may be actuated by sensors monitoring pressure, flow, temperature, speed, etc. Other typical applications include crowbar, interlock and emergency/rapid shutdown circuitry. Trip may be accomplished by voltage or current, which must be removed immediately upon tripping.Dual CoilDual coil protectors provide remote shut down option and normal overcurrent protection in the confines of a single breaker pole. This construction saves space by eliminating the need for an additional pole for the voltage trip function.Voltage TripSometimes called “dump circuits” or “panic trip circuits,” these units make it possible to open main power contacts with lower power inputs from one or more sources. This configuration is becoming increasingly more important for sensitive circuitry and denser packaging in automation systems. Available in series, shunt, relay or dual coil configurations.APL/UPL CONFIGURATIONS.187[4.75].312[7.92].187[4.75].110[2.79].295[7.49]REG 4REC 4REG 5REC 5RS.281 ± .020(7.14 ± 0.51)1.940[49.28]BREAKER IN OFFPOSITIONLINELOADNC NO C( 50 AMP)LOAD LINE (>50 AMP)LOADLINE.625 ± .031(15.88 ± 0.79).281 ± .020(7.14 ± 0.51).675 ± .050(17.15 ± 1.27).280(7.11)1.940(49.28)1.290 ± .031(32.77 ± 0.79).280 ± .031(7.11 ± 0.79)1.056 ± .031(26.82 ± 0.79).648 ± .031(16.46 ± 0.79).667 ± .020[16.94 ± 0.51]1.940[49.28].281 ± .020[7.14 ± 0.51].625 ± .031[15.88 ± 0.79].667 ± .020[16.94 ± 0.51]1.275 ± .020[32.38 ± 0.51]1.940[49.28].281 ± .020[7.14 ± 0.51].625 ± .031[15.88 ± 0.79]TRIP SHUNTTRIPNO VOLTAGECOIL DUAL RATING DUAL TRIP RELAY COIL DUAL LOADLINECOIL.V LINELOAD LOADLOAD LINE LOAD RELAYRELAYLINE COILCOIL LINE LOADCOIL COILLINELOADSeries Trip (See Note A)Series Trip with Auxiliary SwitchShunt, Relay and Dual CoilNotes:Tolerance ± .015 [.38] unless noted. Dimensions in brackets [ ]are millimeters.A T erminal sizes:10-32 THD (<50 AMP), ¼ -28 THD (>50 AMP) Metric Terminals (Optional), M5 x 0.8 THD (<50 AMP).B Minimum useable thread length: 10-32 THD (.250 on breakers without terminal boards, .160 with terminal boards) ¼ -28 THD (.200).A P L /U P LInrush Pulse Tolerance (typ)The following table provides a comparison of inrush pulse tolerance with and without the inertial delay feature for each of the 50/60Hz delays. Pulse tolerance is defined as a single pulse of half sine wave peak current amplitude of 8milliseconds duration that will not trip the circuit breaker.APL/UPL OPERATING CHARACTERISTICSAll trip curves and trip currents are specified with the breaker mounted in the normal vertical position at ambient temperature of +25°C. Protectors do not carry current prior to application of overload.Delays 64, 65 and 66Delays 64, 65 and 66 are the latest 50/60Hz delays with short, medium and long trip times respectively. The patented protector design provides both increased tolerance to high inrush induced nuisance tripping and longer trip times at 600 percent. These delays are ideally suited for applications where thermal devices are presently used, such as motor protection or where short duration, high inrush currents are experienced. As shown in a typical motor start-up curve, the delay 66 will provide locked rotor and overload protection. Nuisance tripping is avoided since acceptable short periods of overload will not trip the protector.where known inrush exists). Delay 71 has a short delay for general purpose applications. Delay 72 is long enough to start certain types of motors and most transformer and capacitor loads. Delay 73 is an extra long delay primarily for special motor applications.PERCENT OF RATED CURRENT .001.01110T I M E I N S E C O N D S125PERCENT OF RATED CURRENT.001.011001000110T I M E I N S E C O N D S125PERCENT OF RATED CURRENT.001.011001000.1110T I M E I N S E C O N D S125.001.011001000.1110T I M E I N S E C O N D SPERCENT OF RATED CURRENT.001.01100.1110T I M E I N S E C O N D SDC Delay Curves (typ)A choice of delays is offered for DC applications. Delays 50 and 59 provide fast acting, non-delayed tripping to protect sensitive electronic equipment (not recommended where known inrush exists). Delay 51 has a short delay for general purposeapplications. Delay 52 is long enough to start certain types of motors. Delay 53 is an extra long delay used primarily for special motor applications.DELAY 408007006005004003002001501251000T I M E I N S E C O N D S101.11000100.0110000.001PERCENT OF RATED CURRENT1000900DELAY 418007006005004003002001501251000T I M E I N S E C O N D S101.11000100.0110000.001PERCENT OF RATED CURRENT1000900DELAY 429001000PERCENT OF RATED CURRENT.00110000.011001000.1110T I M E I N S E C O N D S100125150200300400500600700800DELAY 439001000PERCENT OF RATED CURRENT.00110000.011001000.1110T I M E I N S E C O N D S100125150200300400500600700800DELAY 499001000PERCENT OF RATED CURRENT.00110000.011001000.1110T I M E I N S E C O N D S100130150200300400500600700800M A Y T R I PM A Y T R I PM A Y T R I PM A Y T R I PM A Y T R I P400Hz Delay Curves (typ)A choice of delays is offered for 400Hz applications. Delays 40 and 49 are fast acting, non-delayed tripping to protect sensitive electronic equipment (not recommended where known inrush exists). Delay 41 has a short delay for general purposeapplications. Delay 42 is long enough to start certain types of motor and most transformers and capacitor loads. Delay 43 is an extra long delay primarily for special motor applications.A P L /U P LTrip FreeWill trip open on overload, even when the handle is forcibly held on or restrained. This prevents operator from damaging the circuit by holding the handle in the ON position. Trip IndicationThe operating handle moves positively to the OFF position on overload.Ambient OperationOperates normally in temperatures between –40°C and +85°C.Insulation ResistanceNot less than 100 megohms at 500Vdc.Dielectric StrengthWithstands 1500Vac at 60Hz for 60 seconds or 1800Vac for one second from terminal to terminal, and from auxiliary switch terminal to main terminal.EndurancePer UL 1077 (6000 operations at rated load plus 4000operations with no load). Tested at a maximum rate of 6 times per minute. Rating above 50 amperes operate a minimum of 5000 operations.ShockWithstands 100G or more without tripping while carrying full rated current per MIL-Std-202, Method 213, Test Condition I. Instantaneous types (delay 40, 50, 60 and 49, 59, 69) and dual coil configurations are tested at 80% of rated current. Protectors mounted in the handle down position are to be tested with no current applied (per MIL-PRF-55629).VibrationWithstands 10G without tripping while carrying full rated current per MIL-Std-202, Method 204, Test Condition A.Instantaneous types (delay 40, 50, 60 and 49, 59, 69) and dual coil configurations are tested at 80% of rated current.Dual Coil Ratings5-65Vdc and 5-250Vac for three terminal configurations. 5-120Vac and 5-120Vdc for four terminal configurations. Not available in delays 64, 65 and 66.APL Ratings0.050-50 amperes, 65Vdc, 250Vac maximum, 50/60Hz or 400Hz. 51-100 amperes at 65Vdc and 120Vac maximum. Ratings of 0.050-20 amperes at 277Vac, 50/60Hz are available upon request.Auxiliary Switch RatingsREC4 and REC5 are rated at 10 amperes, 250Vac or 3amperes, 50Vdc. REG4 and REG5 are rated at 0.1 amperes, 125Vac.UPL RatingsUPL protectors are UL STD. 1077 (File No. E-66410) and CSA STD. C22.2–No. 235 (File No. LR-26229) recognized assupplementary protectors in the following configurations and ratings. Consult factory for further information.ConfigurationsSeries, Shunt, Relay, Auxiliary Switch, Switch Only, Dual Coil, No Voltage.PolesOne through nine.Moisture ResistanceDesigned to meet the requirements of MIL-PRF-55629 when tested in accordance with Method 106 of MIL-Std-202.Salt Spray (Corrosion)Designed to meet the requirements of MIL-PRF-55629 when tested in accordance with Method 101 of MIL-Std-202.APL/UPL SPECIFICATIONSMoisture ResistanceDesigned to meet the requirements of MIL-PRF-55629 when tested in accordance with Method 106 of MIL-Std-202.Salt Spray (Corrosion)Designed to meet the requirements of MIL-PRF-55629 when tested in accordance with Method 101 of MIL-Std-202.MPL RatingsMPL protectors are UL (File No. E-41607) and CSA (File No. LR-26229) recognized as manual, across the line starters, in the following configurations and ratings. Consult factory for further information.ConfigurationsSeries only with and without auxiliary switch.PolesOne, two or three.ShockWithstands 100G or more without tripping while carrying full rated current per MIL-Std-202, Method 213, Test Condition I. Instantaneous types (delay 40, 50, 60 and 49, 59, 69) are tested at 80% of rated current. Breakers mounted in the handle down position are to be tested with no current applied (per MIL-PRF-55629).VibrationWithstands 10G without tripping while carrying full rated current per MIL-Std-202, Method 204, Test Condition A. Instantaneous types (delay 40, 50, 60 and 49, 59, 69) are tested at 80% of rated current.MPL SPECIFICATIONSAPL/UPL DECISION TABLESHow to OrderThe ordering code for APL/UPL circuit protectors may be determined by following the steps in the decision tables shown here.The coding given permits a self-assigning part number; other configurations may require a factory assigned part number. Typical examples are units with mixed ratings, combinations of styles or constructions not listed in the third decision table, etc. With these, it is suggested that order entry be by description and/or drawings and a part number will be assigned. Additionally, it is a standard policy to establish a factory assigned part number wherever a descriptive drawing exists to provide cross reference, traceability and manufacturing control.When specifying a protector for AC motor start or high inrush applications, the peak amplitude and surge duration should be specified for factory assistance in rating selection.For example, the code shown is the code for a two pole UPL protector with series trip, 20 ampere rating, 50/60Hz. short time delay construction in all poles.To determine the ordering number for your particular APL/UPL unit, simply follow the steps shown. You may use this number to place an order or as a reference for further questions you may have.Notes:A T he most common current values for 100% of rated current arethose listed. Please consult an Airpax office orsales representa-tive for other values.B A ll APL/UPL protectors are constructed with stainless steelsprings and plated parts. As noted in the specifications, all meet normal requirements for moisture and salt spray resistance. If fungus resistance is required in addition to moisture and saltspray resistance, special procedures and markings are employed.C T erminals will be supplied as #10-32 threaded studs up to 50amperes. Above this amperage terminals will be ¼ -28 threaded studs. All standard units will be supplied with a hex nut and two flat washers on each threaded terminal.D W hen metric threaded inserts are specified, breakers rated at50 amperes and below will be supplied with metric threadedterminals. For breakers rated above 50 amperes, ¼ -28 threaded terminals will be supplied.E Black handle standard.Copyright © 2023 Sensata Technologies, Inc.Datasheets provided by Sensata Technologies, Inc., its subsidiaries and/or affiliates (“Sensata”) are solely intended to assist third parties (“Buyers”) who are developing systems that incorporate Sensata products (also referred to herein as “components”). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, valuation, and judgment in designing Buyer’s systems and products. Sensata datasheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular datasheet. Sensata may make corrections, enhancements, improvements, and other changes to its datasheets or components without notice.Buyers are authorized to use Sensata datasheets with the Sensata component(s) identified in each particular datasheet. HOWEVER, NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATASHEETS ARE PROVIDED “AS IS”. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATASHEETS OR USE OF THE DATASHEETS, EXPRESS, IMPLIED, OR STATUTORY , INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY , FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD TO SENSATA DATASHEETS OR USE THEREOF.All products are sold subject to Sensata’s terms and conditions of sale supplied at .SENSATA ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS’ PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY , AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONS-RELATED INFORMATION OR SUPPORT THAT MAY BE PROVIDED BY SENSATA.Mailing Address: Sensata Technologies, Inc., 529 Pleasant Street, Attleboro, MA 02703, USARegional head offices:United States of America Sensata Technologies Attleboro, MAPhone: 508-236-3800E-mail:*******************NetherlandsSensata Technologies Holland B.V.HengeloPhone: +31 74 357 8000E-mail:*******************ChinaSensata Technologies China Co., Ltd.ShanghaiPhone: +8621 2306 1500E-mail: *******************CONTACT US。
AXIS Q6315-LE PTZ 网络摄像头 高端室外适用 HDTV 1080p PTZ 摄像头说
DatasheetAXIS Q6315-LE PTZ Network CameraHigh-end outdoor-ready HDTV1080p PTZ camera with quick-zoom and laser focusAXIS Q6315-LE is a high-speed PTZ camera offering HDTV1080p resolution.It features IR illumination and day/night functionality for surveillance in pitch darkness.With31x optical zoom,laser focus for precise focus and quick-zoom functionality,it allows you to easily follow fast-moving objects.It includes orientation aid and autotracking2with click and track functionality.Privacy masking with mosaic lets you pixelate whole areas of the scene.Plus,with chameleon masking,it automatically changes the color in the masking depending on the background color of the image.Further-more,the TPM module ensures secure storage of all cryptographic keys and certificates.>1/2"sensor with31x optical zoom>IR illumination,D/N functionality>Autotracking2and orientation aid>Laser focus for precise focus with quick-zoom<1sec zoom speed>TPM,FIPS140-2level2certifiedAXIS Q6315-LE PTZ Network Camera Models AXIS Q6315-LE50HzAXIS Q6315-LE60HzCameraImage sensor1/2”progressive scan CMOSLens Focal length:6.91–214.64mm,F1.36–F4.6Horizontal field of view:60.6°–2.0°Vertical field of view:36.5°–1.1°Laser focus,autofocus,P-irisZoom speed:<1sec between any zoom valueDay and night Automatically removable infrared-cut filterMinimum illumination Color:0.06lux at30IRE,F1.36B/W:0.001lux at30IRE,F1.36,0lux with IR illumination on Color:0.09lux at50IRE,F1.36B/W:0.008lux at50IRE,F1.36,0lux with IR illumination onShutter speed1/111000s to1/2s with50Hz1/111000s to1/2s with60HzPan/Tilt/Zoom Pan:360°endless,0.05°–550°/sTilt:+20to-90°,0.05°–500°/sZoom:31x optical,12x digital,Total372x zoomQuick-zoom,nadir flip,300preset positions,tour recording(max10,max duration16minutes each),guard tour(max100),control queue,on-screen directional indicator,set new pan0°,adjustable zoom speed,speed drySystem on chip(SoC)Model ARTPEC-7Memory1024MB RAM,512MB FlashComputecapabilitiesMachine learning processing unit(MLPU)VideoVideo compression H.264(MPEG-4Part10/AVC)Baseline,Main and High Profiles H.265(MPEG-H Part2/HEVC)Main ProfileMotion JPEGResolution1920x1080(HDTV1080p)to320x180Frame rate Up to50/60fps(50/60Hz)in all resolutionsVideo streaming Multiple,individually configurable streams in H.264,H.265andMotion JPEGAxis Zipstream technology in H.264and H.265Controllable frame rate and bandwidthVBR/ABR/MBR H.264/H.265Low latency modeVideo streaming indicatorImage settings Compression,color,brightness,sharpness,white balance,exposure control,exposure zones,image freeze on PTZ,sceneprofiles,rotation,electronic image stabilization(EIS),defoggingContrast,local contrast,autofocus,Forensic WDR:Up to120dB depending on scene,32individual polygon privacy masksincluding mosaic and chameleon privacy masksNetworkSecurity Multi-level user,IP address filtering,HTTPS a encryption,IEEE802.1x(EAP-TLS)a,network access control,user access log,centralized certificate management,secure keystore(CC EAL4certified),TPM(FIPS140-2certified)Network protocols IPv4,IPv6USGv6,ICMPv4/ICMPv6,HTTP,HTTPS a,HTTP/2, TLS a,QoS Layer3DiffServ,FTP,SFTP,CIFS/SMB,SMTP,mDNS (Bonjour),UPnP®,SNMP v1/v2c/v3(MIB-II),DNS/DNSv6,DDNS, NTP,NTS,RTSP,RTCP,RTP,SRTP/RTSPS,TCP,UDP,IGMPv1/v2/v3, DHCPv4/v6,ARP,SSH,NTCIP,LLDP,CDP,MQTT v3.1.1,Syslog, Link-Local address(ZeroConf)System integrationApplication Programming Interface Open API for software integration,including VAPIX®and AXIS Camera Application Platform;specifications at One-Click Cloud ConnectionONVIF®Profile G,ONVIF®Profile S,and ONVIF®Profile T, specification at Onscreen controls IR illuminationQuick-zoomEnable/disable all privacy masksSpeed dryEvent conditions Device status:above operating temperature,above or belowoperating temperature,below operating temperature,fan failure,IP address removed,network lost,new IP address,shock detected,storage failure,system ready,within operating temperatureEdge storage:recording ongoing,storage disruptionI/O:manual trigger,virtual inputMQTT subscribePTZ:PTZ malfunctioning,PTZ movement,PTZ preset positionreached,PTZ readyScheduled and recurring:scheduled eventVideo:average bitrate degradation,day-night mode,live streamopenEvent actions Record video:SD card and network shareUpload of images or video clips:FTP,SFTP,HTTP,HTTPS,networkshare and emailPre-and post-alarm video or image buffering for recording oruploadNotification:email,HTTP,HTTPS,TCP and SNMP trapPTZ:PTZ preset,start/stop guard tourOverlay text,day/night modeWDR modeIR illuminationMQTT publishAnalyticsAXIS ObjectAnalyticsObject classes:humans,vehiclesTrigger conditions:line crossing,object in area,time in area BETAUp to10scenariosMetadata visualized with trajectories and color-coded boundingboxesPolygon include/exclude areasPerspective configurationONVIF Motion Alarm eventMetadata Object data:Classes:humans,faces,vehicles,license platesConfidence,positionEvent data:Producer reference,scenarios,trigger conditionsApplications IncludedAXIS Object Analytics,AXIS Video Motion Detection,AXIS Motion Guard,AXIS Fence Guard,AXIS Loitering Guard,AXIS OSDI Zone,Orientation Aid PTZ,advanced gatekeeper,autotracking2Support for AXIS Camera Application Platform enablinginstallation of third-party applications,see /acapCybersecurityEdge security Software:Signed firmware,brute force delay protection,digestauthentication,password protection,AES-XTS-Plain64256bitSD card encryptionHardware:Secure boot,Axis Edge Vault with secure keystore(CC EAL4+,FIPS140-2level2certified hardware protection ofcryptographic operations and keys)Network security IEEE802.1X(EAP-TLS)a,HTTPS/HSTS a,TLS v1.2/v1.3a,NetworkTime Security(NTS),X.509Certificate PKI,IP address filteringDocumentation AXIS OS Hardening GuideAxis Vulnerability Management PolicyAxis Security Development ModelTo download documents,go to /support/cybersecu-rity/resourcesTo read more about Axis cybersecurity support,go to/cybersecurityGeneralCasing IP66-,IP67,NEMA4X-and IK10-ratedColor:white NCS S1002-BRepaintable metal casing(aluminum),hard coated Polycarbonate(PC)clear dome with Sharpdome technologySustainability PVC freePower Axis High PoE60W SFP midspan1-port:100–240V AC,max1.5AIEEE802.3bt Type3Class6Camera consumption:typical17W(no IR),max51WConnectors RJ4510BASE-T/100BASE-TX/1000BASE-TRJ45Push-pull Connector(IP66)IR illumination OptimizedIR with power-efficient,long-life850nm IR LEDsRange of reach300m(984ft)or more depending on the sceneStorage Support for SD/SDHC/SDXC cardSupport for SD card encryption(AES-XTS-Plain64256bit)Support for recording to network-attached storage(NAS)For SD card and NAS recommendations see Operating conditions -50°C to50°C(-58°F to122°F)Maximum temperature according to NEMA TS2(2.2.7):74°C (165°F)Arctic Temperature Control:Start-up as low as-40°C(-40°F) Start-up temperature:-40°C(-40°F)Humidity10–100%RH(condensing)Storage conditions -40°C to65°C(-40°F to149°F) Humidity5-95%RH(non-condensing)Approvals EMCEN55032Class A,EN55035,IEC62236-4,EN61000-3-2,EN61000-3-3,EN61000-6-1,EN61000-6-2,FCC Part15Subpart B Class A,ICES-3(A)/NMB-3(A),VCCI Class A,RCM AS/NZS CISPR32Class A,CISPR35,EAC,EN50121-4,KC KN32Class A,KC KN35SafetyIEC/EN/UL62368-1,CAN/CSA C22.2No.62368-1,IEC/EN/UL60950-22,CAN/CSA-C22.2No.60950-22,IEC/EN62471risk group2,IEC60825-1Class1,IS13252EnvironmentIEC/EN62262IK10,IEC/EN60529IP66,IEC/EN60529IP67,NEMA250,Type4X,NEMA TS2(2.2.7–2.2.9),IEC60068-2-1,IEC60068-2-2,IEC60068-2-6,IEC60068-2-14,IEC60068-2-27,IEC60068-2-78,ISO21207(Method B)NetworkNIST SP500-267Dimensions Height:261mm(10.3in)With weather shield:ø239mm(9.4in)Without weather shield:ø192mm(7.6in)Weight4800g(10.6lb)IncludedaccessoriesInstallation guide,Windows®decoder1-user license,60WMidspan(including power cable),IP66rated network connector,repaint template,paint paperOptionalaccessoriesAXIS T91/T94Mounting AccessoriesAXIS T8415Wireless Installation ToolAXIS Surveillance CardsFor more accessories,see VideomanagementsoftwareAXIS Companion,AXIS Camera Station,video managementsoftware from Axis Application Development Partners availableat /vmsLanguages English,German,French,Spanish,Italian,Russian,SimplifiedChinese,Japanese,Korean,Portuguese,Polish,Traditional Chinese Warranty5-year warranty,see /warrantya.This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.(),and cryptographic software written by Eric Young (*****************).Environmental responsibility:/environmental-responsibility©2020-2023Axis Communications AB.AXIS COMMUNICATIONS,AXIS,ARTPEC and VAPIX are registered trademarks ofAxis AB in various jurisdictions.All other trademarks are the property of their respective owners.We reserve the right tointroduce modifications without notice.T10154500/EN/M14.9/2301。
活图科技2021年140421PTZ摄像头配件信息说明书
Fully compatible with ACTi software Software Development Kit (SDK) available; ONVIF Compliant
Simultaneous dual streams based on two configurations 28 Kbps - 6 Mbps (per stream) Constant, Variable
Extreme WDR (145 dB); White balance: automatic, hold and manual; Brightness; Contrast; Sharpness; Automatic gain control; 2D+3D Digital Noise Reduction; Flickerless; Defogging; Digital image stablilizer
199.89 [7.9]
275.70 [10.9]
1 2
1 Reset Button 2 Power LED 3 Memory Card Slot 4 Ethernet Port
4 5
3
6
7
8
5 AC 24V Power Input 6 Digital Input/ Output 7 Audio Output 8 Audio Input 8
IP address filtering; HTTPS encryption; Password protected user level; Anonymous login; IEEE 802.1X network access control
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
PT6520LCD Driver IC DESCRIPTIONPT6520 is a dot matrix LCD driver IC. The bitaddressable display data which is sent from amicrocomputer is stored in a build-in display data RAMand generates the LCD signal.The PT6520 incorporates innovative circuit designstrategies to assure very low current dissipation and awide range of operating voltages. The PT6520 permitsthe user to implement high-performance handysystems operating from a miniature battery.APPLICATIONS• Peripheral devices• LCD modules• Electronic instrumentsFEATURES• CMOS technology•8-bit data interface•61 segment output•16 common output•Duty cycle – PT6520 – 1/16 ~ 1/32•2560 bits built-in display data RAM• Master/Slave operation•Low power: 30μW•LCD voltage: 3.5 ~ 13V•Power supply: 2.4 ~ 7V•Available in 100 pins, QFP & C.O.B. BLOCK DIAGRAMSYSTEM BLOCK DIAGRAMORDER INFORMATIONValid Part Number Package Type Top CodePT6520 100 Pin, QFP PT6520/PT6520-QPT6520-H C.O.B. - PIN CONFIGURATIONPIN DESCRIPTIONPin Name FunctionDB0 ~ DB7 Data inputA0 Selection display data or instructions. High: Display data. Low: Instruction.RES Reset the system and selects the interface type for a 68 port/80 port MPU. High: 68 port MPU interface.Low: 80 port MPU interface.(edge trigger)OSC1 Oscillation input pinE/RD Read/Write Enable signal when a 68 port MPU is connected. (Active-Low read enable signal when an 80 port MPU is connected)RW/WR Read/Write select signal when a 68 port MPU is connected.High: read select. Low: write select.(Active-Low writes enable input when an 80 port MPU is connected. Rising edge sensing)OSC2 Oscillation output pinFR LCD Frame (AC-conversion) signal input/outputSEG0 ~ SEG60 Segment output for driving the LCDCOM0 ~ COM15 Common output for driving the LCDCOM31 ~COM16 Common output for driving the LCDM/S Master/Slave select signalVDD 5V power supplyVSS 0V power supply (GND level)V1, V2, V3, V4, V5 Power supplies for driving the LCD, VDD>V1>V2>V3>V4>V5 Note: This is an example of PT6520 family pin assignment. The modified pin names are given below.Product NamePin/Pad Number74 75 96 ~ 100, 1~ 11 93 94 95PT6520 OSC1 OSC2 COM0 ~ COM15 M/S V4 V1INPUT/OUPUT CONFIGURATIONSThe schematic diagrams of the input and output circuits of the logic section are shown below: INPUT PIN: A0, E, R/W, DB0~DB7, M/S INPUT/OUTPUT PIN: FROUTPUT PIN: COM0 TO COM15 OUTPUT PIN: SG0~SG60FUNCTION DESCRIPTIONDISPLAY COMMANDS(Based on the 80 port MPU; the RD and WR commands differ for the 68 port MPU)Command RD WR A0 D7 D6D5D4D3D2D1D0Function1 Display ON/OFF1 0 0 1 01 01110/1Switches the entire display ON or OFF,regardless of the Display RAM’s data orthe internal status. *2 Display START Line 1 0 0 1 10 Display START Address(0-31)Determines the line of RAM data to bedisplayed at the display’s top line(COM0) 3 Page Address Set 11111Page (0-3)Sets the page of the Display RAM in the page address register.4Column (segment) Address Set1 0 0 0 Column address(0-79)Sets the column address of the Display RAM in the column address register. 5 Status Read 0 1 0B U S YA C CO N /O F FR E S E T0000Read the status.Busy 1: Busy (internal processing) 0: Ready statusADC 1: Rightward (forward) output 0: Leftward (reverse) output ON/OFF 1: Display OFF 0: Display ONRESET 1: Resetting. 0: Normal 6 Write Display Data 1 0 1 Write DataWrites the dataon the data bus to RAMThese commandsaccess a previously-specifiedaddress of the Display RAM, after which the column address is incremented by one. 7 Read Display Data 0 1 1 Read DataReads data from the Display RAM onto the data bus.8 ADC Select 1 0 0 1 0 1 00000/1Used to reverse the correspondence between the Display RAM’s column address and segment driver output ports0: Rightward (forward)output 1: Leftward (reverse) output 9 Static Drive ON/OFF 1 0 0 1 0 1 00100/1Selects normal display operation or static all-lit drive display operation. 1: Static drive (power save)* 0: Normal display operation 10 Duty Select 1 0 0 1 0 1 01000/1Selects the duty factor for driving LCD cells. 1: 1/32 duty, 0: 1/16 duty 11 Read Modify Write 1 0 0 1 1 1 00000Increments column address counter by 1 when display is written.(This is not done when data is read) 12End11111110Cancels the Ready Modify Write mode.13 Reset 1 0 0 1 1 1 01Resets the display START line to the 1st line in the register.Resets the column address counter to 0 and page address to 0.RECOMMENDED SOFTWARE FLOWCHARTNotes:1. Command 1: Display On/Off Commands2. When IC power is applied for the first time, the contents of the Display RAM are not defined; thus, it is strongly suggested that the contents of theDisplay RAM must be cleared during the initial setting.CURSOR BLINKING SEQUENCEEND TIMINGMPU INTERFACE (1)80-FAMILY MPU(2)68-FAMILY MPUTYPICAL CONNECTIONS WITH LCD PANEL (FULL DOT LCD PANEL: 1 CHARACTER = 6 X 8 DOTS)(1) DUTY 1/16, 10 CHARACTER X 2 LINES(2) DUTY 1/32, 20 CHARACTERS X 4 LINESLCD DRIVER INTERCONNECTIONSPT6520 – PT6520RELATIONSHIP BETWEEN DISPLAY DATA RAM LOCATIONS AND ADDRESSESd .)S t a r 1/16l e , t h e d i s p l a y a t a d d r e s s 08)TIMING CHARTREAD/WRITE TIMING FOR THE 80-PORT MPUREAD/WRITE TIMING FOR THE 68-PORT MPURESET TIMING FOR 80-PORT/68-PORT DISPLAYABSOLUTE MAXIMUM RATING(Unless otherwise stated, Ta=25℃, VDD=0V)Parameter Symbol Rating Unit Supply voltage (1) VSS -8.0 to 0.3 V Supply voltage (2) V5 -16.5 to 0.3 V Supply voltage (3) V1, V2, V3, V4 V5 to 0.3 V Input voltage VI VSS –0.3 to 0.3 V Output voltage VO VSS –0.3 to 0.3 V Power dissipation PD 250 mW Operating temperature Topr -40 to 85 ℃Storage temperature Tstg -65 to 150 ℃Soldering temperature Tsol 260°C for 10 s (at leads) -DC CHARACTERISTICS(Unless otherwise stated, VDD=0V, VSS=-5/-3V, Ta=25℃)ParameterSymbol Condition Min. Typ. Max. Unit Applicable PinOperatingvoltage (1) (Note 1) Recommended VSS -5.5 -5.0 -4.5 VVSSPotential -7.0 - -2.4 V Operating voltage (2)RecommendedV5 -13 - -3.5 VV5Potential -13 - - V Potential V1, V20.6xV5- VDD V V1, V2 PotentialV3, V4V5 - 0.4xV5 VV3, V4 High input voltageVIHT VSS =-5V VSS+2.0- VDD V (Note 2, 3) VIHC VSS =-5V 0.2xVSS - VDD VIHT VSS =-3V0.2xVSS - VDD (Note 2, 3) VIHC VSS =-3V0.2xVSS- VDD Low input voltageVILT VSS =-5V VSS - VSS+0.8 (Note 2, 3)VILC VSS =-5V VSS- 0.8xVSS VILT VSS =-3VVSS - 0.85xVSS (Note 2, 3)VILC VSS =-3V VSS -0.8xVSSHigh output voltageVOHT VSS=-5V IOH =-3.0mA VSS+2.4- -VOSC2(Note 4, 5)VOHC1 IOH =-2.0mA VSS+2.4- - VOHC2 IOH=-120μA 0.2xVSS - - VOHTVSS=-3V IOH =-2mA 0.2xVSSVOSC2(Note 4, 5)VOHC1 IOH =-2mA 0.2xVSS VOHC2 IOH=-50μA 0.2xVSS Low output voltageVOLTVSS=-5V IOL = 3.0mA- - VSS+0.4V OSC2 (Note 4, 5)VOLT1 IOL = 2.0mA- - VSS+0.4VOLT2 IOL =120μA - - 0.8xVSSVOLTVSS=-3V IOL =2mA 0.8xVSSVOSC2(Note 4, 5)VOLC1 IOL =2mA 0.8xVSS VOLC2 IOL=50μA 0.8xVSS Input leak current ILI -1 - 1 μA (Note 6) Output leak current ILO -3-3μA(Note 7)LCD driver ON resistanceRONTa=25°CV5=-5.0VVSS=-5V - 5 7.5 K Ω SEG0~60COM0~15(Note 9) V5=-3.5V VSS=-5V- 10 50 Static current consumption IDDQ CS =CL =VDD- 0.05 1 μA VDDDynamic current dissipationDuring IDD (1)During displayV5=-5.0VVSS=-5V fCL =2KHz - 2.0 5.0μAVDD (Note 10)Rf=1M Ω- 9.5 15 During display V5=-5V VSS =-3V fCL =2KHz - 1.5 4.5μARf=1M Ω- 6.0 12 IDD (2)During accessTcyc=200KHz, VS5=-5V - 300 500μAVDD (Note 8)VSS=-3V, During access Tcyc=200KHz, VSS=-3V 150 300Input terminal capacity CIN Ta=25°C, f=1MHz- 5.0 8 pF All input terminalsParameterSymbol ConditionMin.Typ.Max.UnitApplicable PinOscillation frequencyFoscRf=1.2M Ω±5% VSS =-5.0V 12 17 25KHz OSC2(Note 5, 6)Rf=1.2M Ω±5%VSS =-3.0V11 16 27 Hysteresis VH0.05VSS0.1VSS- V (Note 2, 3, 4, 5)Notes:1. A wide range of operating voltages is guaranteed, except in case of abrupt voltage fluctuations during MPU access.2. A0, D0~D7, E, R/W pins3. CL, FR, M/S and RES pins4. D0~D75. FR6. A0, E (or RD), R/W (or WR), M/S and RES.7. When D0 to D7 and FR are high impedance.8. During continual writer access at a frequency of tcyc. Current consumption during access is effectively proportional to the access frequency. 9. For a voltage differential of 0.1V between input (V1,…, V4) and output (COM, SEG) pins. All voltages within specified operating voltage range. 10. PT6520 only. Does not include transient currents due to stray and panel capacitances.AC CHARACTERISTICSREAD/WRITE TIMING FOR THE 80-PORT MPU(Ta=25℃, VDD=0V, VSS=-5V)Parameter Signal Symbol Condition Min. Typ.Max UnitAddress hold timeA0, CS tAH8VSS-5V 10 - -ns VSS=-3V 20 - -nsAddress set-up time tAW8VSS=-5V 20 - -nsVSS =-3V 40 - -nsSystem cycle timeWR, RD tCYC8VSS=-5V 1000 - - ns VSS=-3V 2000 - - nsControl pulse width tCCVSS=-5V 250 - - nsVSS =-3V 500 - - nsData set-up timeD0~D7 tDS8VSS=-5V 100 - - ns VSS=-3V 200 - - nsData hold time tDH8VSS=-5V 40 - -ns VSS=-3V 80 - -nsRD access time tACC8VSS=-5V - -120ns VSS=-3V - -250nsOutput disable time tOH8CL=100pF 10 -60ns CL=100pF,VSS=-3V20 -120nsREAD/WRITE TIMING FOR THE 68-PORT MPU(Ta=25℃, VDD=0V, VSS=-5V)ParameterSignal SymbolCondition Min. Typ.Max Unit System cycle timeA0, CS, R/W tCYC6VSS =-5V 1000 - - nsVSS =-3V 2000 - - ns Address set-up timetAW6 VSS =-5V 20 - - nsVSS =-3V 40 - - ns Address hold time tAH6VSS =-5V 10 - - nsVSS =-3V 30 - - ns Control pulse width D0~D7tDS6VSS =-5V 80 - - nsVSS =-3V 160 - - ns Data set-up time tDH6VSS =-5V 10 - - ns VSS =-3V 20 - - ns Data hold time tOH6 CL=100pF VSS=-5V 10 - 60 ns CL=100pFVSS=-3V20 - 120nsRD access time tACC6 CL=100pF VSS=-5V - - 200nsCL=100pF VSS=-3V - - 400nsEnable disable time READ E tewVSS =-5V 250 - - nsVSS =-3V 400 - - ns WRITE VSS =-5V 150 - - nsVSS =-3V 250- - ns Note: tCYC6 indicates the cycle during which CS/E are high; it does not indicate are cycle of the E signal.CONTROL TIMING FOR 80-PORT/68-PORT MPU(Ta=25℃, VDD=0V, VSS=-5V)ParameterSignal Symbol ConditionMin.Typ.MaxUnitReset time REStRVSS =-5V 1 - 750 μs VSS =-3V 1.5 - 1000μsReset time (68-Port) RES tR1VSS =-5V 1 - - μsVSS =-3V 1.5 - - μsReset time (80-Port)RES tR2VSS =-5V 1 - - μsVSS =-3V 1.5 - - μsNotes:1. The input timing of the FR delay time is determined by the PT6520 (Slave)2. The output timing of the FR delay time is determined by the PT6520 (Master)PAD LAYOUT (PT6520D*A)1001510152025303540455080 75 70 65 60 55959085XY3.44mm4.07mmAI PADChip Specification Dimension (mm) Chip size 3.44 x 4.07Chip thickness 0.400+0.025Pad size 0.095 x 0.095PAD COORDINATES OF PT6520D*A(Coordinate unit: um)Pin no. Name X Y Pin X Y Pin X Y1 COM5 76.4 3535.2 35 SEG37875.476.4 69 SEG3 3365.42270.22 COM6 76.4 3420.2 36 SEG361025.476.4 70 SEG2 3365.42385.23 COM7 76.4 3305.2 37 SEG351175.476.4 71 SEG1 3365.42500.24 COM8 76.4 3190.2 38 SEG341325.476.4 72 SEG0 3365.42615.25 COM9 76.4 3075.2 39 SEG331475.476.4 73 A0 3365.42781.96 COM10 76.4 2960.2 40 SEG321625.476.4 74 OSC1 3365.42896.97 COM11 76.4 2845.2 41 SEG311775.476.4 75 OSC2 3365.43011.98 COM12 76.4 2730.2 42 SEG301925.476.4 76 E(RD#) 3365.43126.93365.43241.99 COM13 76.4 2615.2 43 SEG292075.476.4 77 R/W(WR#)10 COM14 76.4 2500.2 44 SEG282225.476.4 78 Vss 3365.43356.911 COM15 76.4 2385.2 45 SEG272375.476.4 79 DB0 3365.43471.912 SEG60 76.4 2270.2 46 SEG262525.476.4 80 DB1 3365.43586.913 SEG59 76.4 2155.2 47 SEG252675.476.4 81 DB2 3013.83996.914 SEG58 76.4 2040.2 48 SEG242825.476.4 82 DB3 2833.83996.915 SEG57 76.4 1925.2 49 SEG232975.476.4 83 DB4 2653.83996.916 SEG56 76.4 1810.2 50 SEG223125.476.4 84 DB5 2473.83996.917 SEG55 76.4 1695.2 51 SEG213365.4200.285 DB6 2293.83996.918 SEG54 76.4 1580.2 52 SEG203365.4315.286 DB7 2113.83996.919 SEG53 76.4 1465.2 53 SEG193365.4430.287 Vdd 1933.83996.920 SEG52 76.4 1350.2 54 SEG183365.4545.288 RES# 1753.83996.921 SEG51 76.4 1235.2 55 SEG173365.4660.289 FR 1573.83996.922 SEG50 76.4 1120.2 56 SEG163365.4775.290 V5 1282.73996.923 SEG49 76.4 1005.2 57 SEG153365.4890.291 V3 1167.73996.924 SEG48 76.4 890.2 58 SEG143365.41005.292 V2 1052.73996.925 SEG47 76.4 775.2 59 SEG133365.41120.293 M/S 937.7 3996.926 SEG46 76.4 660.2 60 SEG123365.41235.294 V4 822.7 3996.927 SEG45 76.4 545.2 61 SEG113365.41350.295 V1 707.7 3996.928 SEG44 76.4 430.2 62 SEG103365.41465.296 COM0 592.7 3996.929 SEG43 76.4 315.2 63 SEG9 3365.41580.297 COM1 477.7 3996.930 SEG42 76.4 200.2 64 SEG8 3365.41695.298 COM2 362.7 3996.931 SEG41 275.4 76.4 65 SEG7 3365.41810.299 COM3 247.7 3996.932 SEG40 425.4 76.4 66 SEG6 3365.41925.2100 COM4 132.7 3996.933 SEG39 575.4 76.4 67 SEG5 3365.42040.234 SEG38 725.4 76.4 68 SEG4 3365.42155.2PACKAGE INFORMATION100 PINS, QFPSymbol Min. Nom. Max.A - - 3.40A1 0.25 - 0.50A2 2.55 2.70 2.90b 0.22 0.30 0.33c 0.11 - 0.23D 23.20BSCBSC D1 20.00E 17.20BSCBSC E1 14.00BSCe 0.65REF L1 1.60θ 0° 3.5° 7° Notes:1. Refer to JEDEC MO-112 GC-12. All dimensions are in millimeter.PT6520V1.921 July 2010 IMPORTANT NOTICEPrinceton Technology Corporation (PTC) reserves the right to make corrections, modifications, enhancements, improvements, and other changes to its products and to discontinue any product without notice at any time.PTC cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a PTC product. No circuit patent licenses are implied.Princeton Technology Corp.2F, 233-1, Baociao Road,Sindian, Taipei 23145, TaiwanTel: 886-2-66296288Fax: 886-2-29174598。