ProEIM100N网络督察技术规格
西宁市公安局城中公安分局技术用房信息化(综合布线)系统设备参数
序号设备名称规格参数单位数量A-1六类屏蔽信息模块 1、RJ45六类屏蔽模块用于六类链路2、RJ45六类屏蔽模块的打线部分设计有保护盖，在恶劣环境中保护内部IDC触点正常工作。
3、RJ45六类屏蔽模块连接片采用镀金铜铍合金；IDC采用铜磷合金，须和网线同一品牌4、模块材料使用镀锡铜合金制成。
RJ45六类屏蔽模块规格：（1） 直流电阻：≤ 0.3Ω，（2）绝缘阻抗：不低于500MΩ，（3） 拔插寿命：≥ 700次，（4）端接寿命：≥ 200次，（5）接点阻抗：≤ 20mΩ，（6）电流：1.5A，须和网线同一品牌个360A-2单口信息面板 1、面板上可以混合安装RJ45非屏蔽模块、RJ45屏蔽模块、语音模块。
2、86型结构，前后可双向拆卸模块，可以安装在国标86型底盒上。
3、模块框架可从面板正面、背面双向拆卸，方便更换模块且不损伤相邻缆线4、要求面板为86型，采用双层面板结构，以便与强电面板匹配。
5、面板上要求带有滑盖式永久防尘盖6、面板要求带有有机玻璃标签框，在对标签具有良好保护的同时，便于更换标签。
7、面板须和网线同一品牌个360A-3六类跳线3米(信息面板到桌面）1、屏蔽链路应使用RJ45-RJ45型屏蔽原装跳线。
2、铜缆跳线所用对绞缆线要求为多股双绞线，不允许使用单股线。
3、所有跳线的两端须具有接头护套，两端护套颜色必须一致。
4、长度：3米。
5、颜色：蓝色。
条360A-4六类屏蔽双绞线 1.缆线要求外护套采用PVC材料,外护套为蓝色护套2.双绞线均采用紧护套型双绞线3.六类屏蔽双绞线绝缘材料采用HDPE，芯线材料为五氧铜,芯线直径为0.57mm4.六类屏蔽双绞线的主要技术规格：（1）芯线规格：AWG 23；（2）测试带宽：≥ 250Hz；（3）近端串扰：≥ 38.3dB/250MHz；（4）直流电阻：≤ 9.5Ω；5）线缆外径：≥6.3mm，每箱长度≥305米。
5、六类屏蔽双绞线须提供厂家出具质保承诺书.箱70A-524口六类配线架1、水平屏蔽配线子系统中的配线架应采用跳接式配线架。
室内环境监测传感器 AM100 系列用户手册说明书
室内环境监测传感器AM100系列用户手册安全须知为保护产品并确保安全操作，请遵守本使用手册。
如果产品使用不当或者不按手册要求使用，本公司概不负责。
严禁拆卸和改装本产品。
请勿将产品放置在不符合工作温度、湿度等条件的环境中使用，远离冷源、热源和明火。
本产品作为室内环境监测使用，不可作为计量工具使用。
如长期未使用本产品，请将电池取下。
否则可能造成电池泄漏并损坏内部元件。
请勿使产品受到外部撞击或震动。
清洁产品时请避免产品进水以及使用各种清洁剂或溶剂，如苯和酒精。
表面清洁可用湿润的软布擦拭，再用干燥的软布擦干。
为了您的设备安全，请及时修改设备默认密码（123456）。
产品符合性声明AM100系列符合CE,FCC和RoHS的基本要求和其他相关规定。
版权所有©2011-2022星纵物联保留所有权利。
如需帮助，请联系星纵物联技术支持:邮箱：*********************电话:************传真:************总部地址：厦门市集美区软件园三期C09栋深圳：深圳市南山区高新南一道TCL大厦A709日期版本描述2020.06.16V1.0第一版2020.08.07V1.1新增电子墨水屏多种显示模式和配置示例，App界面更新OC、CO2屏幕告警阈值可设置2.ToolBox软件中文图片替换2020.09.25V2.0版式替换2021.03.02V2.1更新版式，型号AM100/AM102变更为AM104/AM107 2021.12.30V2.2更新品牌Logo目录一、产品简介 (5)1.1产品介绍 (5)1.2产品亮点 (5)二、产品结构介绍 (5)2.1包装清单 (5)2.2外观概览 (6)2.3产品尺寸（mm） (6)2.4电子墨水屏 (7)2.4.1显示说明 (7)2.4.2屏幕模式切换 (8)2.5电源按钮 (9)三、电池安装 (9)四、产品配置 (9)4.1配置方式 (10)4.1.1NFC配置 (10)4.1.2USB配置 (11)4.2LoRaWAN基本配置 (12)4.3时间同步 (14)4.4基本设置 (15)4.5高级设置 (16)4.5.1数据采集设置 (16)4.5.2校准设置 (16)4.5.3告警设置 (17)4.6维护 (17)4.6.1升级 (17)4.6.2备份 (18)4.6.3重置 (19)五、产品安装 (20)5.1安装注意事项 (20)5.2安装方法 (20)六、数据通信协议 (21)七、星纵云管理 (22)7.1添加星纵网关 (22)7.2添加AM104/AM107到星纵云 (24)附录 (25)二氧化碳浓度参考 (25)一、产品简介1.1产品介绍AM100系列室内环境监测器由星纵物联自主研发和设计，内置温度、湿度、光照、红外探测、TVOC、CO 2、大气压等多种传感器，帮助我们持续监测办公室、卧室、博物馆等空间的环境变化，及时调整，改善舒适度。
WP系列智能巡回检测报警仪
Registration NO.014-ARegister NO:CNAB006-Q ISO9001:2000/ 中国国际双认证CE 认证WP 系列智能巡回检测报警仪使用说明书上润精密仪器有限公司WIDE PLUS PRECISION INSTRUMENTS CO., LTD.目录1、概述 (1)2、型号规格 (1)3、技术规格 (2)4、安装与接线 (3)5、前面板及功能操作 (5)5.1 前面板 (5)5.2 功能操作 (6)6、参数设置 (6)6.1 设置报警值 (6)6.2 设置公用组态参数 (7)6.3 设置打印参数 (9)6.4 设置各通道组态参数 (10)7、功能及相应参数说明 (11)7.1 输入信号及显示 (11)7.2 零点和满度修正 (12)7.3 冷端补偿 (13)7.4 报警 (13)7.5 控制单元 (14)7.6 打印 (15)7.7通信 (16)1、概述WP系列智能巡回检测报警仪适用于32点、48点和64点过程量的检测和报警。
可输入热电阻、热电偶、直流电流、直流电压等传感器、变送器信号。
基本误差小于0.2%F·S，显示范围-1999~9999各通道独立设定输入信号类型、量程、报警值各通道独立设定数字滤波时间常数，有效提高抗干扰能力各通道独立设定零点和满度修正，有效减小传感器误差，提高系统测量精度可任意关闭不使用的通道2级参数。
第2级参数受密码控制，防止误操作。
具备参数复制功能，大大减小参数设置的工作量独特实用的报警功能，可配接WPCU多点控制单元实现各通道的报警输出手动、定时、报警启动打印快速、高效的通信接口，大大缩短通信时间2、型号规格1 2 3 4 5 6 7 8 9WP /☐—☐☐☐ S ☐ P ☐ V ☐☐☐☐1：尺寸A：横式160×84×182 开孔152+1×76+1（宽×高）16和32路B：竖式84×160×182 开孔76+1×152+1（宽×高）16和32路C：方形160×160×343 开孔152-0.5×152-0.5（宽×高）48及64路2：通道数3：输入信号R：全部通道均为热电阻仪表内装的分度号包括：Pt100，Cu100，Cu50，BA1，BA2，G53E：全部通道均为热电偶仪表内装的分度号包括：K，S，R，B，N，E，J，TB：全部通道均为4mA~20mA或1V~5V等电流、电压信号，需在订货时明确电流，电压信号的输入通道X：输入为热电阻、热电偶混用。
JUMO eTRON M 100温度控制器说明书
Page 1/6JUMO GmbH & Co. KGDelivery address:Mackenrodtstraße 14,36039 Fulda, GermanyPostal address:36035 Fulda, Germany Phone:+49 661 6003-0Fax:+49 661 6003-607e-mail:*************Internet: JUMO Instrument Co. Ltd.JUMO HouseTemple Bank, RiverwayHarlow, Essex CM 20 2TT, UK Phone:+44 1279 635533Fax:+44 1279 635262e-mail:*************.uk Internet: JUMO Process Control, Inc.8 Technology Boulevard Canastota, NY 13031, USA Phone:315-697-JUMO1-800-554-JUMOFax:315-697-5867e-mail:************Internet:Block diagramSpecial featuresk Choice of “electrical” or“hot gas” defrosting process k 16A relay for cooling unit and 8A relay for defrosting and fan functions k 2 analog inputs for RTDs,KTY1X-6 or KTY2X-6in 2-wire circuitk Customized linearization is programmable through the setup program k Operating hours counter with integrated service counter k Alarm generation via relay or buzzer k Available with real-time clock, data logger, and RS485 interface k The data logger records the measurement inputs and switching states of all relays. This makes it possible to implement HACCP monitoring of the cold chain. k Up to 8 parameters can be enabled individually for the operating level k The parameter level is protected by a code, thus preventing any unauthorized access to the instrument data.k Meets the requirements as per EN 12830 and EN 13485k Setup program for instrument configuration andevaluation of the data loggerJUMO eTRON M100Electronic Refrigeration Controller76mm x 36mm formatBrief descriptionfreezer cabinets or cold displays, for connection to RTD probes Pt100, Pt1000, KTY1X-6 or KTY2X-6. The first measurement input is used to acquire the temperature of the cold store. The second measurement input acquires the evaporator temperature, and ends the defrosting process as soon as the limit for defrosting has been reached.The measurements and parameters are shown in a 3-character backlit display.Three relays are available for the cooling unit, the defrosting heating, and the fan.Alarms can optionally be generated via a relay or by means of the integrated buzzer.The switching states of the relays are indicated via yellow LEDs. Further options include a data logger with an adjustable recording interval for HACCP-compliant documentation 1, an RS485interface, and a real-time clock. The electrical connection is made via screw terminals. Four keys serve for instrument operation and parameterization.A setup program and a PC interface are available as accessories, for easy parameterization from the PC, and for evaluating the data logger.Type 701061/...HACCP : H azard A nalysis and C ritical C ontrol P ointApprovalsDisplays and controlsTechnical dataAnalog inputsEnvironmental influencesOutputLED below the symbols A PC interface and an adapter (4-pole socket) are used to connect the instrument to a PC.Ambient temperature range 0to 55°C Storage temperature range -40to +70°CClimatic conditions ≤85% rel. humidity, no condensationShock und vibration DIN EN 60068-2-6 schedule C.2, Frequency-Range: 10 to 55 HzAcceleration: 20 m/s 2 (2g)Care of the front panelThe front panel can be cleaned with normal commercial washing, rinsing and cleaning agents.Do not use any solvents such as methylated spirits, white spirit, P1 or xylol !Relay for cooling, changeover (SPDT)Relay for alarm, changeover (SPDT)70 000 operations at 16A, 250V AC, 50Hz resistive load 60.000 operations at 16A, 250V AC, 50Hz cos phi > 0,6Relay for defrosting, make (SPST -NO)Relay for fan, make (SPST -NO)100 000 operations at 8A, 250V AC, 50Hz resistive load 85.000 operations at 8A, 250V AC, 50Hz cos phi > 0,6RS485 interfaceSupply voltageHousingElectrical dataApproval/MarksMaximum baud rate38.4kbaud Maximum transmission length <1200m Maximum number of stations 32PriorityThe RS485 must not be used while the setup interface is in operation !Supply voltage 12—24V AC/DC +15/-15%, 48 — 63Hz (for operation with SELV circuits only !)(not electrically isolated from the analog inputs)Power consumption< 3WMaterial polycarbonate, silver gray RAL 7001Mountingin panel cut-out, with bezel sealOperating position unrestricted Weightapprox. 160g Enclosure protection to EN 60529,IEC 529IP65 front, IP20 rearFlammability classUL 94 V0Data backupThe data sets of the data logger are saved to a flash memory.The adjustable parameters are stored in EEPROM.Data are preserved after a power interruption.Data logger:Recording duration depending from Recording interval (Parameter rEC)Connection circuitscrew terminals for wire cross-sections up to 4 mm 2, solid wire,up to 2.5 mm 2, stranded wireElectromagnetic compatibility interference emission interference immunity Product family standard: EN 61326Class Bto industrial requirementsOperating conditions The instrument is designed as a panel-mounting unit.Electrical safetyEN 60730, Part 1, overvoltage category III, pollution degree 2Accuracy of the real-time clock,bufferingat 25°C: +15/- 15 sec per month, temperature effect: - 0.35 ppm/10°Cwithin the ambient temperature range: +60/- 60 sec per monthGold Cap capacitor buffers the clock time unpowered for about 20 days.Technical and functional characteristics of temperature recording devices or thermometersas per EN 12830 and EN 13485Abbreviation Inspection authority valid forULUnderwriters Laboratoriesonly valid for mass-production units with the JUMO symbolrEC Recording duration 1 min 7 days 19 hours5 min 39 days (1 month, 9 days)15 min 117 days (4 month)60 min 469 days (1year 3 months)120 min938 days (2 years 6 months)Connection diagramDimensionsType 701061/...Controller functionsCooling, defrosting and fan functionsSpecial function: cooling and heating with fan relay2 Pt100 push-in probes (extra code 236)Standard accessories- 1 Operating Manual - 1 spring clip and bezel sealAccessories - Price Sheet 70.9770Sales No.Setup program, multilingual70/00485306PC interface with USB/TTL converter, adapter (socket) and adapter (plug)70/00456352PC interface TTL /RS232 converter and adapter (socket)70/00350260Accessories - Price Sheet 70.9710Sales No.Adapter frame for mounting on DIN rail70/00483019Order details(1)Basic version701061JUMO eTRON M100with 2 measurement inputs and 3 relay outputs(2)Basic type extensions x 8factory-set, configurablex 9configuration to customer specification Option 1x 0not available x 1buzzerx 2alarm contact, changeover (SPDT) contact 16A/250V Option 2x 0not available x 1RS485 interfacex 2data logger, real-time clock, and RS485 interface (3)Supply voltagex 3212—24V AC/DC +15/-15 %, 48—63Hz (4)Extra codesx 000no Pt100 push-in probe x2362 Pt100 push-in probes(diameter: 6mm, fitting length: 50mm, connecting cable: 1500mm)(1)(2)(3)(4)Order code /-/Order example701061/800-32/000。
1668ENH类别5e网线、双4双综线，F UTP，LSZH室内CPR Eca说明书
Product:1668ENHCategory 5e Cable, 2 x 4 Pair, F/UTP, LSZH Indoor CPR EcaProduct DescriptionCategory 5e Premise Horizontal Cable (100MHz) shotgun, 2 x 4-Pair, 24 AWG solid bare copper conductors, F/UTP, Polyethylene insulation, Beldfoil® shield, AWG 26 solid tinned copper drainwire, LSZH jacketTechnical SpecificationsProduct OverviewConstruction DetailsConductorInsulationCable CoreOuter ShieldOuter JacketElectrical CharacteristicsElectricalsDelayHigh Frequency1 2.1 dB/100m65.362.363.260.26461204035 4 4 dB/100m56.353.352.3249.35249233423 10 6.3 dB/100m50.347.344414441253015 168 dB/100m47.244.239.236.239.936.9252810.9 209 dB/100m45.842.836.833.8383525279 31.2511.4 dB/100m42.939.931.528.534.131.523.625.1 5.5 62.516.5 dB/100m38.435.421.918.928.125.121.52210021.3 dB/100m35.332.31411242120.120Table Notes:Limits below 4 MHz are for information only. Reference standard: IEC 61156-5Transfer ImpedanceFrequency Max. Transfer Impedance1 Mhz Max. 50 mOhm/m10 Mhz Max. 100 mOhm/m30 Mhz Max. 200 mOhm/m100 Mhz Max. 1000 mOhm/mTransfer Impedance Class:Grade 2Screening Class:Type IITable Notes:Coupling AttenuationVoltageVoltage Rating72 V DCMechanical CharacteristicsTemperatureOperating Installation-30°C to +60°C0°C To +50°CBend RadiusStationary Min.Installation Min.24 mm (0.94 in)48 mmMax. Pull Tension:130 N (29 lbf)Bulk Cable Weight:78 kg/kmStandards and ComplianceEnvironmental Suitability:Indoor - Euroclass EcaFlammability / Reaction to Fire:IEC 60332-1-2CPR Compliance:CPR Euroclass: EcaIEEE Compliance:PoE: IEEE 802.3bt Type 1, Type 2, Type 3Data Category:Category 5eTIA/EIA Compliance:ANSI/TIA 568.2-DISO/IEC Compliance:ISO/IEC 11801-1, IEC 61034-2 - Smoke Density Min Transmittance = 60%CENELEC Compliance:EN 50173-1, Segregation class according EN50174-2 = aEuropean Halogen Free Standards:IEC 62821-1 Halogen Free Compliance = Yes, IEC 60754-1 - Halogen Amount = Zero, IEC 60754-2 - Halogen Acid Gas Amount - Max. Conductivity = 2.5 µS/mm, IEC 60754-2 - Halogen Acid Gas Amount - Min. pH = 4.3European DirectiveCompliance:EU CE MarkUK Regulation Compliance:UKCA MarkProduct NotesNotes:Electrical values are expected performance based on cable testing and representative performance within a typical Belden system. HistoryUpdate and Revision:Revision Number: 0.283 Revision Date: 12-12-2023Part NumbersVariantsItem #Color Putup Type Length EAN1668ENH.00500Gray, RAL 7032Reel500 m8719605003195© 2023 Belden, IncAll Rights Reserved.Although Belden makes every reasonable effort to ensure their accuracy at the time of this publication, information and specifications described here in are subject to error or omission and to change without notice, and the listing of such information and specifications does not ensure product availability.Belden provides the information and specifications herein on an "ASIS" basis, with no representations or warranties, whether express, statutory or implied. In no event will Belden be liable for any damages (including consequential, indirect, incidental, special, punitive, or exemplary damages) whatsoever, even if Belden has been advised of the possibility of such damages, whether in an action under contract, negligence or any other theory, arising out of or in connection with the use, or inability to use, the information or specifications described herein.All sales of Belden products are subject to Belden's standard terms and conditions of sale.Belden believes this product to be in compliance with all applicable environmental programs as listed in the data sheet. The information provided is correct to the best of Belden's knowledge, information and belief at the date of its publication. This information is designed only as a general guide for the safe handling, storage, and any other operation of the product itself or the one that it becomes a part of. The Product Disclosure is not to be considered a warranty or quality specification. Regulatory information is for guidance purposes only. Product users are responsible for determining the applicability of legislation and regulations based on their individual usage of the product.。
公安局网上督察系统设备清单
一、县局督察支队监控中心服务器及平台软件
23 24
服务器机柜 设备小计
图腾服务器专用
台
4600
1
4600 473200
二、基层办案单位内部设备 序号 1 2 3 4 5 6 7 8 9 10 11 三、总计 产品名称 网络硬盘录像机（4路D1） 网络硬盘录像机（8路D1） 网络硬盘录像机（16路D1） 网络交换机 网络红外半球 网络红外枪机 拾音器 电话监察终端 监控级硬盘 辅助线材 合计 ZXNVM 4路NVR ZXNVM 8路NVR ZXNVM 16路NVR 华三2414/S1224 ZNNC SD-IFF2N-3N-NC3P ZNNC IR-F502W-O 快鱼E-TRADIO DCVG-ISIO ST31000525SV 单位 台 台 台 台 台 台 台 台 块 批 单价 5400 7200 9800 1560 1980 2260 320 2100 800 500 数量 21 2 2 28 95 23 95 21 36 118 总价 113400 14400 19600 43680 188100 51980 30400 44100 28800 59000 593460
单位
台 台 台 台 台 套 套 套 套 套 套 套 套 套 台 台 套 套 台 套 台 套
单价
21800 32600 21800 26720 37200 12800 20300 9200 16800 18200 13650 16100 21000 21000 98000 6000 980 25000 10600 8000 7600 6650
数量
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 1
总价
21800 32600 21800 26720 37200 12800 20300 9200 16800 18200 13650 16100 21000 21000 98000 12000 980 25000 21200G(1颗) SUGON I420R-G(2颗) SUGON I420R-G(1颗) DCVP-500H DCVP-500H-R SIP-MON-Base ZXSPS-CMS ZXOSS-WEB ZXOSS-SCS ZXOSS-MAS ZXOSS-MRS ZXSPS-MCS ZXOSS-MDS ZXOSS-MM-VAM 华为OceanStorS2600 DELL 780MT 797-101A/1000TC KR6000/6KVA在线式4小时 LD HDL40 定制2联4席位 S5700-24TP-SI-AC AS-3108ELG
AEM TestPro CV100多功能电缆测试器用户手册说明书
For more information: | Enquiries:*************************North America: AEM International (US) 5560 West Chandler Blvd,Suite 3, Chandler, AZ 85226 | toll free 833-572-6916| 480-534-1232Asia: AEM Singapore Pte. Ltd. 52 Serangoon North Ave 4 Singapore 555853Revision 4/5/2019 | V.1.0TestPro CV100Multifunction Cable TesterVersatility for the Digital AgeProvided by:(800)404-ATECAdvanced Test Equipment Corp .® Rentals • Sales • Calibration • ServiceOverviewcost savings through better management of the holistic infrastructure thatencompasses the IP network, heating and cooling, building security systems andmore. What all of this means to you is that the need for network bandwidth andpower has never been greater and it is rapidly increasing, with the adoption oftechnologies such as PoE and Multi-Gigabit Ethernet over copper cabling.To meet this growing need, AEM designed the TestPro, an affordable, versatileand rugged testing solution for today’s complex network environments. TestProprovides you with the ability to fully ensure infrastructure readiness to support thedeployment of IoT connected devices be it lighting, multi-sensor cameras,building entry, wireless APs, monitors, computer workstations, or even long hauland single pair applications.The best part, all of this comes at an affordable price that will allow organizationsto outfit more technicians to optimize efficiency during both deployment as well asongoing management and troubleshooting., and more….Copper CertificationThe TestPro platform features the most sophisticated RF measurement engine available and has independent ETL/Intertek verification of ANSI/TIA-1152-A (Levels IIIe and 2G), IEC 61935-1 Ed. 4 (Levels IIIe, IV and V) and IEC 61935-1 Ed. 5 Draft 46/595/CD (Levels VI Class I and II), and a 3GHz frequency range. What this means to you is that you can be assured of your certification results for CAT5e – CAT8 with an accuracy range that not only exceeds industry standards but even older well-known cable testers and that your testing needs will be met today and tomorrow. TestPro has also been approved by industry leading cable manufactures in support of their warranty programs.As part of the six second CAT6A standard Autotest, TestPro will perform these measurements for both Channel and Permanent Link.·Length including distance to fault ·Propagation Delay ·Delay Skew·Loop Resistance·DC Resistance Unbalance for both Pair to Pair and Wire to Wire ·Return Loss ·Impedance·Insertion Loss ·NEXT ·PSNEXT ·ACRF ·PSACRF ·TCL ·ELTCTLTestPro ’s LiveWiremap ™ facilitates rapid cable continuity testing with automatic display of result the moment the cable is attached. TestPro offers fault location for Return Loss and NEXT aiding in problem identification. Support for MPTL, Patch Cord, Cat8, and Coax is available through hot swappable Adapters. At thecompletion of the Autotest, you will get a highly visible Pass or Fail indication, and test results can be automatically saved with a customizable labeling scheme.TestPro will store over 10,000 results in memory, but when it’s time to prepare printed reports, the included TestDataPro PC based software provides a way to organize and manage results and provide printed reports. If you’re testing PoE and Multi -Gigabit Ethernet in addition to cable certification, you can even produce printed reports that include all three measurements by combining the results of a certification Autotest and a Multi-Gigabit Autotest.Both Channel and Permanent Link Adapters are included in the TestPro CV100-K50, K51, K60, K61 Kits.These Adapters are also sold separately modelsAD-CAT6A-CH, AD-CAT6A-PL.Fiber Optic CertificationTestPro’s fiber optic measurements provide Tier -1 certification in compliance with IEEE 802.3 series, TIA-568.3-D, IEC-14763-3, as well as customizable limits for bothMultimode and Singlemode Fiber Optic premise cabling. Additionally, these adapters include an integrated Visual Fault Locator (VFL) to provide a quick indication of a break in the fiber, as well as an integrated connection port for measuring electrical voltage for hybrid powered fiber applications in support of smart building initiatives. Encircled Flux (EF) compliant source means no need for bulky external adapters. Fiber optic test kits include, reference launch cords, coupler, interchangeable FC on TX port andinterchangeable LC on RX port, cleaning kit, and carrying case. SC and FC adapters and reference launch cords are available as accessory items and sold separately. As part of the four second Autotest, TestPro will perform the following measurements for both Singlemode and Multimode.·Dual ended loss ·Single ended loopback loss ·Length andpropagation delay·Optical power meter OM1-OM5·Integrated Voltmeter ·LiveWiremap·Printed report includes test data and Compliant NetworksMultimode adapters support testing of OM5 fiber in addition to earlier generation fiber standards. For deployments where powered fiber is being used, TestPro ’s fiber adapter provides not only certification of the fiber optic cable but also provides you with the ability to validate electrical voltage on the adjacent copper wire in this hybrid cable type. This allows you to measure the electrical input voltage going into a PoE extender that issupplying PoE to end devices, and is a convenience for the technician to have everything needed for testing at their fingertips. Combine that with TestPro’s ability to measure actual PoE load (requires AD-NET-CABLE adapter) and you have a powerful solution with a unique set of capabilities that will allow you to verify and troubleshoot across various points in the network typology.In single fiber applications, TestPro fiber adapters can be configured as a light source and receiver in power meter mode.Both SM and MM Adapters are included in the TestPro CV100-K11, K51, K61 Kits. These Adapters are also sold separately models AD-SM-01 and AD-MM-01.Power Over Ethernet (PoE) Validation TestPro excels at validating PoE with the most comprehensive test functionality availableand in compliance with TIA 1152A and IEEE 802.3 at/af/bt standards. What sets TestProapart is the ability to validate the Power Source Equipment (PSE), a.k.a. the switch with actual power load, the only true way to validate if the level of power needed at the jack where a Powered Devices (PD) will deploy, such as a Camera, AP, Window Covering, etc. is to measure actual power at the jack with a report of available Voltage, Current, and Real Power expressed in Wattage.As part of the validation test, TestPro allows you to select which standard you want to testagainst be it 802.3 af/at/bt. In doing so, TestPro will request the highest level of power loadfrom the PSE for that standard and will perform the following tests:·PSE Detection ·Voltage ·PSE Type ·PD Class ·PoE Cable Pairs·Allocated Power·Current·Real Power·Sustained Power Load MonitoringFor those pesky intermittent power issues, TestPro allows for sustained loading of the PSE over longer periods, through external loads. This allows you to monitor live for any power fluctuation that drops below the required level threshold. TestPro can also characterize the cabling links for DC resistance unbalance parameters either as part of a standard cable certification Autotest or as a one-off quick test.PoE load testing is available in the TestPro CV100-K30, K60, K61 Kits. This Adapter is also sold separately modelAD-NET-CABLE.Multi-Gigabit Link Speed QualificationTestPro qualifies cabling links for 1 / 2.5 / 5 / 10Gigabit Ethernet in accordance with 802.3ab, IEEE 802.3bz, and IEEE 802.3an respectively. TestPro reports these values based on end-to-end Signal to Noise Ratio (SNR) operating margin, to provide an objective assessment of link performance under network load condition. TestPro’s Multi-Gigabit Autotest is a quick and easy one button operation to ensure that a cabling link will support the desired network rate.·Validation test-10/100 Mbps- 1 Gbps·QoS-SNR 2.5 Gigabit-SNR 5 Gigabit-SNR 10 Gigabit·PoE Load TestWireless access points (APs) are one oftoday's most broadly deployed type ofdevices and 802.11ac Wave 2 wireless APsrequire 2.5 and 5 GigE backbone speeds torun at maximum performance. TestPro’sSignal to Noise (SNR) basedmeasurements will provide you with apass/fail indication of supported speed. Improvements in 10Gigabit technology,price, and performance have extended itsreach beyond enterprise data centers tomidmarket networks. Increasing bandwidth requirements and the growth of enterprise applications are also driving broader deployments of 10 Gigabit Ethernet. TestPro’s 10Gigabit testing provides a true indication through Pass/Fail indication as well as visibility into available headroom even down to per pair detail.Multi-Gigabit qualification testing isavailable in the TestPro CV100 K30, K60,K61 Kits. This Adapter is also soldseparately model AD-NET-CABLE.TestDataPro Results Management Software TestDataPro is a PC based results management software that comes standard with all models of TestPro.TestDataPro works in tandem with TestPro, which allows you to define projects and categorize test results intological groupings once uploaded into the database. The database provides you with the ability to collaborate by viewing in-depth test details on-line as well as provide .pdf based printed reports. TestDataPro allows you to export results in .csv or .pdf format.Options are available that allow you to combine an entire job worth of test results into a single .pdfdocument to pass along to a customer. Additionally, if you want to combine specific test results such asa Copper and Fiber certification tests, Multi-Gigabit and PoE test into a single Smart Building report, theflexibility in reporting allows you to customize the output to meet your specific needs.Singlemode FiberTest ReportFormoreinformation:|Enquiries:*************************North America: AEM International (US) 5560 West Chandler Blvd, Suite 3, Chandler, AZ 85226 | toll free 833-572-6916 | 480-534-1232 Asia: AEM Singapore Pte. Ltd. 52 Serangoon North Ave 4 Singapore 555853Revision 4/5/2019 | V.1.0TestPro Product Kits All kits come with:-Two TestPro Platforms-Certificate of Calibration for each TestPro -USB Flash Drive with TestDataPro-Carry Case/s -Two Wiring Rack Hanging Straps-Quick Start Guide-USB cable-Two Power Adapters with country specific PinsTestPro CV100-61 Smart Building Test Kit Copper/FiberAdapter and Accessories GuideTestPro is a highly versatile test platform that allows you to expand functionality as needed. There is one TestPro Platform and two are provided in each kit. The platform is compatible with all adapters, regardless of which kit you initially purchased.AD-SM-K01 SM FIBER TEST KIT FOR TESTPRO Single mode fiber test kit for TestPro for tier 1 fiber certification testing. Contains a pair of single mode fiber adapters with dial wavelength light source 1310/1550nm, visual fault locator, volt meter, pair of interchangeable FC adapter for the transmit port, pair of FC-LC launch cords for connecting the transmit port to the fiber link under test, pair of interchangeable LC adapters for the receive port, pair of LC-LC reference cords for the receiveAD-MM-K01 MM FIBER TESTKIT FOR TESTPRO Multimode fiber test kit for TestPro for tier1 fiber certification testing. Contains pair of Multimode fiber adapters with dial wavelength light source 850/1300nm, visual fault locator, volt meter, pair of interchangeable FC adapter for the transmit port, pair of FC-LC launch cords for connecting the transmit port to the fiber link under test, pair of interchangeable LC adapters for the receive port, pair of LC-LC reference cords for the receiveAD-NET-CABLE MULTIGIG & POE ADAPTER PAIR A pair of Multi-gig SNR testing and PoE testing adapter for TestPro AD-CAT6A-CH CAT6A CHANNEL ADAPTER PAIR A pair of CAT6A channel test adapter for TestPro CV100AD-CAT6A-PL CAT6A PERMANENT LINK ADAPTER PAIR A pair of CAT6A permanent link adapter for TestPro CV100ACC-6A-PL-PLUG REPLACEABLE PLUG FORAD-CAT6A-PLA pair of field replaceable centered plugs for AD-CAT6A-PLAD-M12-X M12 X-CODED ADAPTER PAIR A pair of M12 X-coded adapters for TestPro CV100AD-5e-PCORD CAT-5E PATCH-CORD TEST ADAPTER PAIR A pair of patch-cord test adapters for testing CAT5e patch-cords using AD-6-PCORD CAT-6 PATCH-CORD TEST ADAPTER PAIR A pair of patch-cord test adapters for testing CAT6 patch-cords using AD-6A-PCORD CAT-6A PATCH-CORD TEST ADAPTER PAIR A pair of patch-cord test adapters for testing CAT6A pitch-cords using AD-8.2-TERACH CAT 8.2 TERA CHANNEL ADAPTER PAIR A pair of CAT 8.2 TERA channel adapter for TestPro CV100AD-8.2-TERAPL CAT 8.2 TERA PERM LINK ADAPTER PAIR A pair of CAT 8.2 TERA permanent link adapters for TestPro CV100 AD-8.2-GG45CH CAT GG45 TERA CHANNEL ADAPTER PAIR A pair of CAT 8.2 GG45 channel adapter for TestPro CV100AD-8.2-GG45PL CAT GG45 TERA PERM LINK ADAPTER PAIR A pair of CAT 8.2 GG45 permanent link adapters for TestPro CV100 OP-CA T6A CAT6A LICENSE FOR TESTPRO CV100 CAT6A cable certification testing license for TestPro CV100UP-K05-K50 UPGRADE FROM K05 TO K50 Upgrade kit from TestPro CV100-K05 to TestPro CV100-K50Kit contains: OP-CA T6A software license code for enabling CAT6A certification testing, a pair of AD-CAT6A-CH channel adapters, a pair ofUP-K30-K60 UPGRADE FROM K30 TO K60 Upgrade kit from TestPro CV100-K30 to TestPro CV100-K60Kit contains: OP-CA T6a software license code for enabling CAT6A certification testing, a pair of AD-CAT6A-PL permanent link adaptersACC-HARD-CASE HARD CARRY CASE FOR TESTPRO ACC-SOFT-CASE SOFT CARRY CASE FOR TESTPRO ACC-POWER-AD AC POWER ADAPTER FOR TESTPROTechnical SpecificationsTESTPRO PLATFORMEach platform in a kit comes with a certificate of Calibration traceable to NIST. SIZE200mm X 105mm X 50mmDISPLAY5” TFT color touch screen,resolution 800 x 480 pixelsBATTERY-Li-Ion- 3.7V / 13,200 mAh-9 hr. battery life typicalPOWER ADAPTER-5V, 3A (supplied)-5-12V (supported)- 2.1mm DC jackPLATFORM OPERATING SYSTEMLinuxCPU1GHz ARM Cortex-A8USB INTERFACES-USB flash drive storage-MicroUSB for connecting to PCRJ-45 SIDE PORT10/100/1G network connectivity test port TEST ADAPTER TO PLATFORM INTERFACE-High-frequency connector rated for 5000 insertion cycles-Hot-swappableMEASUREMENT ENGINE-9-channel dual-endedmixed-mode RF and DC measurementengine-Industry’s highest performance patent-pending measurement architecture fordata cable testingFREQUENCY RANGE-0.1 – 3,000 MHzFREQUENCY RESOLUTION-0.125 MHz-Supports all frequency ranges required by TIA 1152A, ISO/IEC 61935-1and beyond COPPER TESTINGMEASUREMENT TIME-CAT6A auto-test (including TCL andresistance unbalance tests): 6 sec-CAT 8 Class II auto-test: 30 secWIREMAP-All possible wire connection situationsidentified, as long as two wires areconnected end-to-end on any pinsDC RESISTANCE-Range: 0 to 50 Ω-Pair-to-pair and within pair resistanceunbalance measurement meets TIA1152A specsTONE GENERATOR730Hz and 1440 HzDUAL-ENDED RF MEASUREMENTS-IL, RL, NEXT, ACR-F, TCL-All mandatory and optional RFmeasurements as per TIA andISO/IEC standards-single-pair link testing license withsupported length for dual endedtesting greater than 1,000 mLENGTH (PROPAGATION DELAY)MEASUREMENT-Dual ended test: 0 – 600m with 0.1mresolution(0 – 6,000 nsec with 1 nsec resolution)-Delay skew measurement with 1 nsecresolutionSUPPORTABLE CABLING-4-pair twisted pair cable-1-pair twisted pair cable-Coax cable-Optical cables (SM/MM pair)TDR- RL-0-100 m (resolution: 1 m)-Distance-to-faultTDR- NEXT-0-100 m (resolution: 1 m)IMPEDANCE-0-1000 Ω-0.1 Ω resolution in 90-110 Ω rangeFIBER OPTICCOMMON TO BOTH MM AND SMSupplied Test Interface: interchangeableFC on TX port and interchangeable LC onRX portVFL LIGHT SOURCEWavelength 650nmVOLTMETERMeasurement range: 0-60V DCOPTICAL POWER METERmeasurement range: -3 dBm to -30 dBmSPECIFICATONS APPLICABLE TO AD-MM-01 MULTIMODE ADAPTERWAVELENGTHS850nm, 1300 nmLIGHT SOURCELEDTRANSMIT POWER-20 dBm typicalENCIRCLED FLUXCompliant to IEC- 61280-4 and TIA-526-14-C-2015 as per supplier data sheetLENGTH MEASUREMENT-range: up to 2 km (subject tomaximum 10dB link loss)-Length measurement resolution: 0.1mDUAL ENDED LOSSDual ended loss measurement: 0 to -10 dBSPECIFICATIONS APPLICABEL TO AD-SM SINGLEMODE ADAPTERWAVELENGTHS1310nm, 1550nmLIGHT SOURCELaser VCSELOPTICAL POWER-2dBm typicalLENGTH MEASUREMENT-Length measurement range: up to 20km (subject to maximum 20dB linkloss)-Length measurement resolution: 0.1mDUAL ENDED LOSSDual ended loss measurement: 0 to -20 dBPOWER OVER ETHERNET-PoE source type detection-Load test up to 90W-Identification of PoE pairs-Sustained load monitorMULTI-GIGABIT ETHERNETAUTO-TEST PARAMETERS-Signal to Noise Ratio at eachspeed across each pair-Cable diagnostics-PoE detectionWarranty and Extended Care CoverageStandard WarrantyTestPro CV100 platform offers a 2-year warranty against manufacturing defects.Extended CareExtended Care is optional coverage for TestPro Kit that protects your investment with complementary repair or replacement (at our discretion) for any type of damage done to the TestPro platform. Coverage for test Adapters includes free yearly replacement of damaged Adapters, which must be returned as part of the replacement program. Free adapter replacement excludes individually purchased AD-SM-01 and AD-MM-01. Coverage also includes Calibration service for both TestPro platforms. Complementary loaner testers are available upon request and availability.For TestPro Kits that include fiber optic adapters, Extended Care covers those adapters for yearly calibration and repair service.Extended Care programs are offered in 1 and 3 year options.Calibration ServiceIf Extended Care is not purchased and testers are due for calibration, stand-alone calibration service is available for TestPro Platforms and AD-SM-01 and AD-MM-01 fiber optic Adapters.Formoreinformation:|Enquiries:*************************North America: AEM International (US) 5560 West Chandler Blvd, Suite 3, Chandler, AZ 85226 | toll free 833-572-6916 | 480-534-1232 Asia: AEM Singapore Pte. Ltd. 52 Serangoon North Ave 4 Singapore 555853Revision 4/5/2019 | V.1.0For a more detailed look at product capabilities, product kits, and to see the latest cable manufacturer warranty approvals,please visit /Products。
BDM100系列技术资料V2.1
PR100说明书
基本安全说明1.该产品可以用在操作条件下和该厂家指定位置下进行操作。
操作时通风要正常。
除非有其他说明，r&s公司产品使用时有如下要求：ip 防护2x,污染等级2，过压等级2，只用于封闭空间，最大操作海拔2000米.⒉在执行工作时，必需遵守当地的或者国家的安全守则和用于防止意外事件的章程。
该产品只能有被授权的专业人士打开。
在使用该产品执行任何工作或操作时，该仪器必须从供电网断开。
任何的校正，部件更换，维护或者检修必须由r&s公司认可的技术人员执行。
由于安全原因，只允许使用原厂配件（例如电源开关,电力变压器,保险丝）。
与安全相关的部件呗更换后，必须进行一个安全试验（外观检查,电缆缆芯测试，绝缘电阻测量，漏电流测量,功能测量）。
⒊正如工业制成品情况一样,物质导出一个过敏反应的物质比如铝，不能被排除。
如果你发展过敏反应(比如皮疹,频繁的嚏喷红色信号灯或者呼吸困难),咨询一个内科医生来确定原因。
⒋依靠在该功能,确信产物比如正向读出无线电设备能产生一升高的电平的电磁辐射。
因为未来的生活要求增强防护,孕妇应该经过合适手段进行保护。
带着起搏器的人也可以被电磁辐射危及。
雇主必需估定工作位置上的辐射危险性，如有必要,采取措施避开危险。
⒌操作该产品要求有专业训练和强烈的精神集中。
残疾人不应该使用该产品除非确定他们的残疾对操作产品没有有害影响。
⒍在接通该产品之前,必须保证它的标称电压符合交流电源的标称电压。
如果设置为不同的电压，产品的电源熔丝将会相应熔断而被更换。
⒎产品安全等级为一级，有可拆卸电源线和连接器,操作只允许在接口有接地点时进行。
⒏不允许损坏接地线或者仪表的接口。
否则可能导致触电危险。
如果使用了延长线或者连接器，必须定期地核对他们以保证他们使用安全。
⒐如果该产品没有切断交流电源的电源开关,连接电缆的插头被认为是切断装置。
在这样的情况下，必须保证电源插头一直处于容易达到和易接近的（连接电缆长度近似2米） 2m). 功能或者电子开关不适于提供切断交流电源。
PMU100EN操作手册
PMU100EN 标准电量测控仪PMU100EN 标准电量测控仪操作手册镇江默勒电器有限公司共7页 镇江默勒电器有限公司 V2.0! 好 备 准 运 亚 ： 喊 呐 奋 中 心 都 每 刻 时 这 为 加 累 力 努 份 淀 积 子 日 个 许 涉 跋 新 崭 段 却 者 愿 志 们 我 而 。
验 生 的 会 盛 育 体 受 享 口 门 家 在 次 一 了 始 开 ， 人 数 多 大 绝1.1 实时参数测量 1.2 电度计量 1.3 谐波分析(选项)1.4 增选功能 种规格： 220V 相电压/380V 线电压 57.7V 相电压/100V 线电压 ② 测量电流分两种规格： 5A 电流 1A 电流 ③备注： ① 测量电压分两1.概述PMU100EN 标准电量测控仪是一种简单可靠的测控装置，可以 广泛应用于电力系统、环境监控、低压配电等自动化领域。
通过操作面板（6 个按键和液晶） ，PMU100EN 的大部分参数可 显示和被编程。
·相电压实时值 ·线电压实时值 ·频率 ·相电流、零序电流 ·有功电度（0-999，999，999KWH） ·无功电度（0-999，999，999KvarH） ·相电压 31 次谐波 ⑥ ⑤PMU100EN 支持 100 条 SOE 事件记录， 时间分辨率 2ms，可以对开 关量动作、继电器动作、定值触发条件等事件进行记录④ 开关量输入分两种规格： 有源节点 无源节点 继电器容量分两种规格： 250VAC/5A 30VDC/5A 250VAC/10A 30VDC/10A 模拟量输入分两种规格： 4-20mA 电流型输入 0-5V 电压型输入实现功能如下： ·实时参数测量 ·电度计量 ·谐波分析(选项) ·增选功能 在本产品中，开关量输入、继电器输出、模拟量输入、RS485 通讯 等作为增选功能进行配置。
SM100-TCP 远程数据采集器 使用说明书
SM100-TCP远程数据采集器使用说明书嘉兴市松茂电子有限公司目录1、SM100-TCP远程数据采集器介绍 (3)1.1产品简介 (3)1.2产品性能 (3)1.3主要参数 (3)2、SM100-TCP采集器实物图及指示灯功能 (4)2.1实物图 (4)2.2SM100-TCP产品选型 (4)2.3接线图 (4)2.4端口介绍 (4)2.5指示灯说明 (5)3、配置软件功能介绍及操作步骤 (6)3.1通讯连接 (6)3.2配置以太网络参数 (7)3.3基本参数设置 (10)3.4HART透明工作方式 (11)3.5HART自动通讯参数配置 (12)3.6MODBUS TCP数据查询 (13)3.7ModScan软件 (14)4、服务与保修 (15)免责声明：在您使用本产品前，请您仔细阅读本文档。
因不按文档规定的方法使用，而对本产品造成的任何损坏，本公司将不予以承担责任。
这篇文档是本公司为本产品所作的产品说明，但由于产品或软件升级等原因有可能造成文档中的部分内容变化或者失效，我们不保证由此产生的一切后果，请注意版本变化，并及时更新。
为及时取得最新信息，请随时留意我们的网站:，如果您对这篇文档或本产品的性能描述有什么不明之处，请你联系你的供应商或与我们直接联系，********************，QQ:2850687718以供咨询和解答。
版权声明：本篇文档的版权由本公司独家享有，任何人在未取得本公司书面许可前，不得以任何形式（包括转抄、复印、翻译、电子邮件等形式）向第三方透露本文的任何内容。
1、SM100-TCP远程数据采集器介绍1.1产品简介SM100-TCP远程数据采集器是集成HART协议与TCP/IP通讯于一体的高科技产品，是微型RTU 系统。
它以高档ARM单片机为核心，由高精度运算放大器、接口芯片、看门狗电路、输入输出回路等组成，并且嵌入TCP/IP网关模块及HART调制解调芯片，具有性能稳定、性价比极高等特点。
PT-100型号的最大功率点跟踪器（MPPT）充电控制器说明说明书
Model Numbersyy PT-100Available Foryy RenewableEnergy SystemsOff-grid PowerBack-up PowerWorks Withyy ME Seriesyy MM-AE Seriesyy MM-E Seriesyy MMS Seriesyy MMS-E Seriesyy MS Seriesyy MS-AEJ Seriesyy MS-E Seriesyy MSH Seriesyy MS-PAE Seriesyy MS-PE Seriesyy MMP Panel Systemyy MMP-E Panel Systemyy MP Panel Systemyy MP-E Panel Systemyy RD Seriesyy RD-E SeriesAvailable Configurationsyy Works as a stand-alonecontroller using internal settingsyy Works with a Magnum-Dimensions Inverter/Charger and Magnum-Dimensions Remote. Menu settings for the PT-100 are currently onlyavailable via the ME-ARC Remote The PT-100 is a Maximum Power Point T racker (MPPT) charge controller designedto harvest the maximum available energy from the PV array and deliver it to the batteries. The PT-100’s MPPT algorithm finds the maximum power point of the array and operates at this point while regulating the output current to 100 amps and battery voltage to fully charge the battery.Featuresyy High Efficiency: The PT-100 providestypical 99% conversion efficiency anduses less than four watts of power innighttime mode.yy MPPT: Maximum Power PointT racking technology for increasedPV power output efficiency.yy Voltage Options: Compatible with12, 24, or 48V battery systems withautomatic detection of system voltage.The PT-100 will produce up to 100amps regardless of battery voltage.yy Supports a Large PV Array:A single controller supports a largePV array up to 6600W. Larger PVarrays may be used because the PT-100is current limited to 100 amps formaximum harvest.yy Optimal Battery Charging:Automatic battery temperaturecompensation using an includedexternal temperature sensor foroptimum battery charging, even duringextreme temperature changes.yy Multi-stage Charging:Maximizes system performanceand improves battery life.yy GFDI: Integrated PV Ground-Fault Detection and Interruption/Indication, with pre-fault leakage/diagnostic metering.yy LED Indicators and Screen:Multiple LED indicators and largedigital LED screen on front panel foreasy-to-read system information.yy On-site Updates: The PT-100’ssoftware can be updated on site.yy Extensive Electronic Protection:Over-temperature protection, powerderating when temperature is high,PV short circuit and high PV inputshutdown, output overcurrentprotection and night-time back-feed(reverse current) protection.yy AFCI: An integrated PV Arc-Fault Circuit Interrupter detects,indicates, and extinguishes series arcs.yy Convenient Installation: Run all ofthe wiring to the unique, remain-in-place wiring box with ease prior toinstalling the full PT-100 unit.yy Easy MP and MMP integration:The PT-100 is designed to work witha Magnum Panel (MP) or Mini-Magnum Panel (MMP). It providesroom and access to PV and batterydisconnect breakers.Even More Functionality withthe Optional Remoteyy Built-in programmable auxiliary relayfor device control.yy Internal data logging functionalitykeeps energy harvest information andbattery Ahr/Whr data up to 255 days.Use the optional remote to displaythis information.The World Depends on Sensors and Controls OFFICES 2211 West Casino Road Everett, Washington 98204 USA425-353-88334467 White Bear Pkwy St. Paul, MN 55110 USA800-553-6418 PT-100 CHARGE CONTROLLER SPECIFICATIONSTesting for specifications at 25° C. Specifications subject to change without notice.August 2015 Rev C Part #64-0660Maximum PV input voltage (any condition)200 VDC + battery voltage or 240 VDC - whichever is lower Maximum PV operating voltage187 VDC Maximum PV array short circuit current100 ADC Nominal battery voltage range12, 24, or 48 VDC Battery charger output voltage range10 to 66 VDC Continuous charger output current100 ADC (from -20 °C to +40 °C) with proportional power reduction up to 60 °C ambient Maximum output power6600 watts Efficiency99% typical Tare loss / nighttime power consumption<4 watts (fan off, display/LEDs off)Charger regulation method Automatic three-stage (bulk, absorption, float) charge with manual equalizationBattery temperature compensation With Battery Temperature Sensor (BTS) connected (battery temperature -20 °C to +55 °C)Internal cooling Using dual ball-bearing fans for long lifeOvercurrent protection With two overlapping circuitsOver-temperature protection On transformer and MOSFETSListings ETL Listed to UL/cUL 1741, CSA C22.2 #107.1-01, CEWarranty Five years parts and laborOperating temperature -20° C to +60° C (-4° F to 140° F)Nonoperating temperature -40° C to +70° C (-40° F to 158° F)Operating humidity 0 to 95% RH non condensingEnclosure type Indoor, ventilated, with removable powder-coated conduit boxUnit dimensions (w x h x d)8.5” x 15.5” x 4.0” (21.6 cm x 39.4 cm x 10.2 cm)Shipping dimensions (w x h x d)11.5” x 19.5” x 8.125” (29.2 cm x 49.5 cm x 20.6 cm)Mounting Mounted on a vertical surface (wall) or installed on MP or MMP enclosureWeight 13.6 lb (6.2 kg)Shipping weight 18 lb (8.2 kg)Max operating altitude15,000’ (4570 m)。
IMP100-12 品牌：UEOnline 型号：IMP100-12 产品：用户手册说明书
. THE RECOMMENDED FACING DOWN), SPECIFICALLY WHERE HEAVY CONDENSATION IS EXPECTED.C o n t r o l s m ay b e m o u n t e d a n d o p e r a t e d i n a n y position. They may be surface mounted via the two mounting ears on either side of the enclosure, or directly to a rigid pipe by using the pressure connection. Low pressure and differential pressure units, models 520-535, 540-543, 544-548, are also available with an option-al surface mounting bracket. Should the control be installed where con-densation is expected, vertical mounting is recommended as a means of keeping water away from switch terminals.SOLDER OR WELDED JOINT.On models supplied with an external manual reset button, be sure to leave sufficient finger space over the reset button for the operator to reset the control.WIRIngRECOMMENDED TIGHTENING TORQUE FOR FIELD WIRING TERMINALS IS 7 TO 17 IN-LBS.Remove the two screws retaining the cover and cover gasket. A 1/2” NPT conduit connection is provided on the left hand side of the enclosure. Two cast-in knockouts for the 1/2” conduit are located on the side and back of the enclosure. These can easily be knocked out by placing the blade of a screwdriver in the groove and tapping sharply with a hammer. The three switch terminals are clearly labeled “common”, “normally open” and “normally closed”.BEFORE INSTALLING, CHECK THE SENSOR MODEL SELECTED FOR COMPATIBILITY TO THE PROCESS MEDIA IN CONTACT WITH THE SENSOR AND WETTED PARTS.The 100 Series pressure and differential pressure switches are activat-ed when a bellows, diaphragm or piston sensor responds to a pressure change. This response, at a pre-determined set point, actuates a single snap-acting switch, converting the pressure signal into an electrical sig-nal. Control set point may be varied by turning the internal adjustment hex. (See Adjustment - PART II)., TESTING). CONTINUOUS OPERATION SHOULD NOT EXCEED THE DESIGNATED OVER RANGE** OR WORKING PRESSURE RANGE***.*Proof Pressure - the maximum pressure to which a pressure sensor may be occasionally subjected, which causes no permanent damage (e.g., start-up, testing). The unit may require re-gapping.**Over Range Pressure - the maximum pressure to which a pressure sensor may be continuously subjected without causing damage and maintaining set point repeatability.***Working Pressure Range - the pressure range within which two opposing sensors can be safely operated and still maintain set point repeatability.Please refer to the product technical brochure for product specifica-tions. Product technical brochures may be found at .Tools needed Adjustable WrenchScrewdriverHammer (for alternate wire knockouts)MounTIng100 Series Type H100(Pressure Switch)Type H100K(Differential Pressure)IMP100-12Please read all instructional literature carefully and thoroughly before starting. Refer to the final page for the listing of Recommended Practices, Liabilities and Warranties. For functional safety applications, please refer to the safety manual which can be downloaded Part I - InstallationU N I T E D E L E C T R I C C O N T R O L SInstallation and Maintenance InstructionsSIL2CertifiedRe-gapping Procedure (refer to Figure 1)1. Loosen adjustment lock.2. Turn 5/8” hex adjustment screw clockwise (left), to approximately midrange. This puts a load on the sensor and exposes the plunger flats. 3. Using a 1/4” wrench on the plunger and a 3/16” wrench on the plung-er hex screw, turn hex screw counter-clockwise (right) from plunger until switch actuates. If switch is already actuated, turn plunger hex screw clockwise (left), until switch deactuates. Turn hex screw clock-wise (left) from this point. (See chart 1 for Flats and approximate Gap.)4. Check set point per above.5. Connect wires and replace cover securely.Models Flats Approx. gap 171-1742-2 1/2.0085 to .0105”183-1941-1 1/2.004 to .006”483-4941-1 1/2.004 to .006”358-3765-6.020 to .025”700-706 3 1/2 - 4.014 to .017”521-5252-2 1/2.0085 to .0105”157375-6.020 to .025531-5352-2 1/2.0085 to .0105”540-5482-2 1/2.0085 to .0105”565-5671-1 1/2.004 to .006”156235-6.020 to .025”15731-157365-6.020 to .025For optional switches supplied with leadwires, the following color coding applies:Manual Reset DPDT (Option 1530)(Option 1010)SPDTCircuit 1Circuit 2 Common Violet Violet Yellow Normally Closed Black Black Red Normally Open BlueBlueOrangeA grounding screw and clamp (cast in symbol) is provided which meets a 35 lb. pull test. Keep the wire as short as possible to prevent interference with the plunger and if applicable, the optional adjustable differential switch wheel (option 1519).Tools needed 5/8” Open End Wrench1/4” Wrench 3/16” WrenchTO THE FUNCTION OF THE CONTROL.Type H100 and H100K (refer to Figure 1)Remove cover. Loosen Phillips screw adjustment lock. Adjust set point by turning 5/8” hex adjustment screw clockwise (left) to raise set point, or counter clockwise (right) to lower set point. Tension on adjustment screw can be increased by tightening adjustment lock onto it. (See Figure 1). Controls include uncalibrated reference scales for high, low or mid range settings. When making adjustments, do not exceed the proof pressure rating on nameplate as this may cause a shift in set point.Types with Adjustable Deadband Switch (Select Models & option 1519)Models 15623, 15731-15737, 15884, and types with option code 1519 incorporate a snap switch with integral adjustment wheel. Turning this wheel raises or lowers the pressure rise set point. The fall set point remains constant. To use the adjustable deadband switch:1. Determine set point and deadband values. For example, a rising setpoint of 20 psi with a deadband value of 6 psi.2. Set the falling set point at desired deadband value (determined bysubtracting the deadband value from the desired set point) using the standard adjustment screw as outlined above. Using the example from step 1, 20 – 6 = 14, so you would set the fall set point at 14 psi. This is your constant.3. Set your deadband by turning the adjustment wheel left to raise orright to lower the set point. Using the example from step 1, turn the wheel left or right until 20 psi is achieved. This is your set point.Consult UE for additional information.Types with Manual Reset Button (option 1530)These optional models incorporate a snap switch that when actuated, remains actuated until the pressure decreases and the reset button (locat-ed on top of the control) is manually depressed to reset the switch.Part II - AdjustmentsChart 1Models 188-194, 488-494DimensionsDimensional drawings for all models may be found at .Models 218-376,610-706, 15623, 15731-15736, 15884Models 520-525, 15737Models 530-5351/2 NPTCONDUITCLEARANCE FOR1/4 (6.35mm) SCREW2 MT'G HOLES.895 (22.7mm) DIA.KNOCK-OUT 2 PLACESDimension AInches mm NPT7.63193.81/2”7.56192.01/2”6.63168.41/2”6.63168.41/2”218 6.56166.61/4”270-2747.00177.81/4”358-3767.00177.81/4”520-525, 157378.44214.41/2”530-5358.00203.21/2”565-567 6.63168.41-1/2” Sanitary Fitting610-616, 680, 158847.00177.81/4”701-706, 15623,15731-157366.63168.41/4”Differential Pressure540-5438.47215.11/8”544-5488.53216.71/8”CP061010000Model 540-543Models 544-548Models 565-567U N I T E D E L E C T R I C C O N T R O L S180 Dexter Ave. P .O. Box 9143, Watertown, MA 02472-9143 USA 617 926-1000 Fax 617 RECOMMENDED PRACTICES AND WARNINGSUnited Electric Controls Company recommends careful consideration of the fol-lowing factors when specifying and installing UE pressure and temperature units. Before installing a unit, the Installation and Maintenance instructions provided with unit must be read and understood.• To avoid damaging unit, proof pressure and maximum temperature limits stat-ed in literature and on nameplates must never be exceeded, even by surges in the system. Operation of the unit up to maximum pressure or temperature is acceptable on a limited basis (e.g., start-up, testing) but continuous operation must be restricted to the designated adjustable range. Excessive cycling at maximum pressure or temperature limits could reduce sensor life.• A back-up unit is necessary for applications where damage to a primary unit could endanger life, limb or property. A high or low limit switch is necessary for applications where a dangerous runaway condition could result.• The adjustable range must be selected so that incorrect, inadvertent or malicious setting at any range point cannot result in an unsafe system con-dition.• Install unit where shock, vibration and ambient temperature fluctuations will not damage unit or affect operation. When applicable, orient unit so that moisture does not enter the enclosure via the electrical connection. When appropriate, this entry point should be sealed to prevent moisture entry.• Unit must not be altered or modified after shipment. Consult UE if modifica-tion is necessary.• Monitor operation to observe warning signs of possible damage to unit, such as drift in set point or faulty display. Check unit immediately.• Preventative maintenance and periodic testing is necessary for critical appli-cations where damage could endanger property or personnel.• Electrical ratings stated in literature and on nameplate must not be exceed-ed. Overload on a switch can cause damage, even on the first cycle. Wire unit according to local and national electrical codes, using wire size recom-mended in installation sheet.• Do not mount unit in ambient temp. exceeding published limits.LIMITED WARRANTYSeller warrants that the product hereby purchased is, upon delivery, free from defects in material and workmanship and that any such product which is found to be defective in such workmanship or material will be repaired or replaced by Seller (Ex-works, Factory, Watertown, Massachusetts. INCOTERMS); provided, however, that this warranty applies only to equipment found to be so defective within a period of 24 months from the date of manufacture by the Seller. Seller shall not be obligated under this warranty for alleged defects which examination discloses are due to tampering, misuse, neglect, improper storage, and in any case where products are disassembled by anyone other than authorized Seller’s representa-tives. EXCEPT FOR THE LIMITED WARRANTY OF REPAIR AND REPLACEMENT STATED ABOVE, SELLER DISCLAIMS ALL WARRANTIES WHATSOEVER WITH RESPECT TO THE PRODUCT, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.LIMITATION OF SELLER’S LIAbILITYSELLER’S LIABILITY TO BUYER FOR ANY LOSS OR CLAIM, INCLUDING LIABILITY INCURRED IN CONNECTION WITH (I) BREACH OF ANY WARRANTY WHATSO-EVER, EXPRESSED OR IMPLIED, (II) A BREACH OF CONTRACT, (III) A NEGLIGENT ACT OR ACTS (OR NEGLIGENT FAILURE TO ACT) COMMITTED BY SELLER, OR (IV) AN ACT FOR WHICH STRICT LIABILITY WILL BE INPUTTED TO SELLER, IS LIM-ITED TO THE “LIMITED WARRANTY” OF REPAIR AND/OR REPLACEMENT AS SO STATED IN OUR WARRANTY OF PRODUCT. IN NO EVENT SHALL THE SELLER BE LIABLE FOR ANY SPECIAL, INDIRECT, CONSEqUENTIAL OR OTHER DAMAGES OF A LIkE GENERAL NATURE, INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS OR PRODUCTION, OR LOSS OR EXPENSES OF ANY NATURE INCURRED BY THE BUYER OR ANY THIRD PARTY.UE specifications subject to change without notice.。
Sennheiser IE 100 PRO Wireless产品说明书
with Bluetooth® connectorFEATURES• Dynamic full-range transducer for high-resolution,powerful monitoring sound• Reduces acoustic stress factors through natural anddistortion-free reproduction• 2 in 1 bundle: Bluetooth® module for wireless connec-tion to mobile devices, PCs or tablets, with a built-inmicrophone for calls or standard 3,5 mm jack-plugcable• Excellent shielding through optimized earpiece shapeand flexible silicone and foam attachmentsFor the stage. For massive sound. For the road.Developed for high expectations on live stages, the specially designed driver of the IE 100 PRO creates precise audio cla-rity for musicians in live sessions. Typical for the new type of membrane is a powerful, high-resolution and warm monito-ring sound. With the included Bluetooth® module, the in-ears become comfortable everyday companions for your mobile phone, PC or tablet. With the built-in mic, phone calls or Webcasts are also possible.Musicians and DJs choose the IE 100 PRO wireless set for its exceptional sound and high wearing comfort. Not only for live sessions, but also for producing on the road or as an everyday companion.The in-ears come with 4 earpiece adapters that optimize the fit for every ear size and shape. The setup is stage-safe from the connection to the cable conduit.Sophisticated monitoring sound for mixing on live stages, producing in the studio and everywhere in between.DELIVERY INCLUDES• IE 100 PRO (BLACK, CLEAR or RED)• Bluetooth connector• black cable for IE 100 PRO• USB-A to USB-C cable• soft pouch• cleaning tool• foam and silicone ear adapters• quick guide• safety guide• compliance sheetwith Bluetooth® connectorPRODUCT VARIANTSIE 100 PRO WIRELESS BLACKArt. no. 509171IE 100 PRO WIRELESS CLEAR Art. no. 509172IE 100 PRO WIRELESS RED Art. no. 509173SPECIFICATIONS IE 100 PROFrequency response 20 - 18,000 Hz Impedance20 ΩSound pressure level (SPL)115 dB (1 kHz / 1 V rms )Total harmonic distortion (THD)< 0.1 % (1 kHz, 94 dB)Noise attenuation < 26 dB Magnetized field strength 1.63 mT Operating temperature Storage temperature –5 °C to +50 °C (23 °F to 122 °F)–20 °C to +70 °C (–4 °F to 158 °F)Relative humidity< 95 %Bluetooth ® ConnectorWearing style Bluetooth® neckband cable Microphone principle MEMS Microphone frequency response100 - 8,000 HzMicrophone sensitivity -42 dBV/Pa (ITU-T P.79)Microphone pick-up pattern (speech audio)omni-directional Power supply - built-in rechargeable lithium- polymer battery 3.7 V ⎓, 100 mAhUSB charging 5 V ⎓, 100 mA max.Operating time10 h (music playback via SBC) with rechargeable battery;240 h in standby mode Charging time ofrechargeable batteries approx. 2.5 hOperating temperature Charging temperature Storage temperature +5 °C to +40 °C ± 5 °C (41 °F to 104 °F ± 9 °F)+10 °C to +40 °C ± 5 °C (50 °F to 104 °F ± 9 °F)–20 °C to +70 °C (–4 °F to 158 °F)Relative humidity Operation: Storage:10 - 80 %, non-condensing 10 - 90 %Magnetized field strength1.63 mT (with IE 100 PRO)0.23 mT (without headphone)Weight approx. 13 gBluetooth®VersionBluetooth 5.0 compatible,class 1, BLETransmission frequency 2,402 - 2,480 MHz Modulation GFSK, π/4 DQPSK, 8DPSK Profiles HSP, HFP, AVRCP, A2DP Output power 10 mW (max)CodecSBC, aptX®, aptX LL®, AACThe Bluetooth® word mark and logos are registered trade-marks owned by Bluetooth SIG, Inc. and any use of such marks by Sennheiser electronic GmbH & Co. KG is under license.with Bluetooth® connectorSennheiser electronic GmbH & Co. KG · Am Labor 1 · 30900 Wedemark · Germany · ACCESSORIESIE PRO Bluetooth Connector Art. no. 508943IE PRO Mono cable Art. no. 508944Twisted cable Art. no. 507478Black straight cableArt. no. 508584。
PTN设备性能指标
项目
标称速率 码型
输出口比特率容差 测试负载阻抗
性能指标
1544kbit/s AMI（Alternate Mark Inversion）或者B8ZS（Bipolar with 8-Zero Substitution） <±32ppm 100Ω
1ppm＝1×10-6。对于2048kbit/s接口，1UI=488 ns。
性能指标
2048kbit/s HDB3（三阶高密度双极性码） 0dB~6dB，1024kHz >±50ppm <±50ppm 75Ω或120Ω 18dB
1ppm＝1×10-6。对于2048kbit/s接口，1UI=488 ns。
ZXCTN 9004&9008电接口性能
T1电接口性能
ZXCTN 9008的T1电接口性能指标如下表：
ZXCTN 9004&9008以太网性能
VLAN ID数量
ZXCTN 9004&9008设备的以太网端口均能识别IEEE 802.1Q规定的C-VLAN ID范围为1~4094；
所有以太网端口可配置VLAN ID的范围为1~4094；
以太网EVC业务数量
业务类型
E-LINE E-LAN+E-TREE
ZXCTN 9004&9008 POS/CPOS光 接口性能
ZXCTN 9004&9008 支持OC-3c/OC-12c/OC48c/OC-192c的POS接口和OC-3的CPOS接口：
OC-3c的POS接口和OC-3的CPOS接口都采用SFP的 光模块，其接口性能指标如下表：
项目
接口速率 光接口类型 工作波长（nm）
ZXCTN 9008以太网 性能
飞思网巡1000E-PRO型产品规格说明(动环版)
飞思网巡1000E-PRO型产品规格说明飞思网巡1000E-PRO型产品为机房全智能监控管理设备。
包括机房动力环境及IP网络设备、服务器运行监控管理和预警。
硬件规格背面黑色标准1U440x450x44.5mm英特尔双核1.8GHz处理器, 带1MB 二级缓存功能1.总体功能a)全中文界面，完全B/S架构，可以在任何地方随时通过浏览器远程管理。
需支持IE、Firefox、Chrome浏览器。
不需安装独立的客户端软件。
b)可根据需要，对界面的首页进行自定义。
将关键的统计数据图形、关键监控内容的列表信息、性能曲线图、最新故障和报警记录等在首页进行编排。
并且支持不同用户帐号进行独立定义。
c)可定义一独立界面，将指定的多个监控内容的性能曲线图进行分页和自动滚动显示。
d)数据展示统一采用可分层的资源树和列表的风格，配以使用直观的饼状图、柱状图和曲线图，以及不同颜色的可视化表达，要求简单明了。
e)提供在线帮助系统，方便管理和使用。
f)基于角色的分级权限管理。
可控制人机界面上的每个功能模块的读和写权限，每个受监控设备和服务器的读和写权限。
g)系统具备运营所需要的帐号权限设置。
可分配大量的运营权限帐号，以使这些帐号能进行登录，并且仅浏览指定监控目标指定时间区间的状态、曲线图、故障日志等内容。
h)同时支持IP、SNMP、WMI、IPMI、TCP Modbus、和各类TCP应用等协议。
i)在不改变现形网络架构前提下实现部署。
j)为以后扩展需要，系统应支持分布式部署能力。
二级平台能独立管理，并能将所有数据实时上传到中心平台，在中心平台统一展示。
k)提供远程协助功能，在用户管理员授权下，远程工程师能通过互联网方便的协助进行系统维护，维护过程中传输的数据应该在VPN通道中保密进行。
不需在前端防火墙做任何端口映射配置。
l)对短信发送，应可支持移动运营商MAS的接口，并支持通过短信Modem发送的能力。
需支持2个或者多个Modem，实现发送负载均衡和备份。
网络信息安全管理系统
网络信息安全管理系统网络信息安全管理系统主要用以内部人员的上网行为进行管理，对其所发布的信息进行审计，防止不良信息散发到互联网上，阻止学生访问不良网站，阻断不必要的网络应用，合理利用网络资源，创造一个绿色的上网环境.技术要求如下:1、产品基本要求:产品部署产品可通过旁路、透明桥接、网关三种对网络数据流进行采集、分析和识别,实时监视网络系统的运行状态，记录网络事件、发现安全隐患，并对网络活动的相关信息进行存储、分析和协议还原;在旁路方式下，系统可以支持多个网口同时采集数据。
产品资质必须具备中华人民共和国公安部的《计算机信息系统安全专用产品销售许可证》，通过以下检测标准:1） GA658-2006 互联网公共上网服务场所信息安全管理系统信息代码2) GA659—2006 互联网公共上网服务场所信息安全管理系统数据交换格式3） GA660—2006 互联网公共上网服务场所信息安全管理系统上网服务场所端功能要求4) GA661—2006 互联网公共上网服务场所信息安全管理系统远程通讯端功能要求5) GA663-2006 互联网公共上网服务场所信息安全管理系统远程通讯端接口技术要求6) MSTL_JBZ_04—024 互联网公共上网服务场所信息安全管理系列标准检验实施细则网络接口产品为硬件形态具有2个以上1000M网络接口2、系统封堵功能:系统提供的不良网站1、系统提供百万条以上网址列表，并支持网址库的自动在线升级; 数量和分类 2、网址库具有不良网站的分类，包括不良言论、暴力、毒品、色情等不良网址. 用户可以自定义网站支持用户根据学校内部的网络应用特点自行定义网站分类和网站站点，系统可分类以对自定义的网站进行按管理策略进行封堵或放行等监控. 对IM类软件的控管 IM类协议的识别：QQ|—-文件传输|—-音视频|—-网络硬盘|-—游戏|-—远程协助｜-—聊天MSN|—-聊天|-—文件传输｜——音视频｜-—游戏Yahoo｜——文件传输｜—-视频｜--聊天ICQ|—-文件传输|——音视频|——游戏|—-聊天网易泡泡｜——游戏|--聊天新浪UC搜QSkype淘宝旺旺可以勾选IM大类对即时通讯应用进行统一控管,也可以独立选择具体的即时通讯软件进行控管，还可以对即时通讯软件的子协议进行控管，例如视频,文件传输等即时通讯封堵系统可以对QQ、MSN、ICQ、YahooMassger按管理策略进行封堵。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
ProEIM100N
网络督察技术规格
上海新网程信息技术有限公司SHANGHAI PRONETWAY INFORMATION TECHNOLOGY CO.,LTD.
产品规格
介绍网络督察产品的外观和规格。
外观
网络督察产品的整体外观如下图所示：
注：外观以根据新网程实际提供的产品为准。
规格
网络督察产品的规格如下：
硬件
♦存储空间：标配80GB，可扩充到160GB
♦网络接口：标配4个10/100BaseT RJ45快速以太网接口
♦硬件BYPASS：标配1对
♦通用串行总线接口（USB）：1个
♦串行控制口（Console）：1个，RJ45接口
物理尺寸
♦尺寸：440(W)x315(D)x45(H)毫米，1U标准19英寸上架型机箱
♦重量：5.5公斤
电源要求（AC）
♦输入电压：100~240V AC
♦满载功率：180W
工作环境
♦工作温度：0到55ºC (32到131ºF)
♦工作湿度：90%相对湿度(RH)
产品指标
网络督察产品性能指标如下表所示：
产品功能
网络督察产品主要功能如下表所示：。