帕克气动管路接头pneumatic pipe fittings(poolke)

合集下载

Parker Pneumatic产品说明书

Pneumatic DivisionRichland, Michigan USA/pneumaticsMO VALVE SERIESBulletin NumberBulletin DescriptionK583092Manual Valve “OU” to O-Ring, Conversion InstructionsK583186Lockout Valve, Installation InstructionsK583187Electrical Enclosure Lockout Valves, Installation InstructionsSafety GuidePDN Safety GuideVisit for additional instruction sheets.(02/20/18)Click here to view bookmarks.To avoid unpredictable system behavior that can causepersonal injury and property damage:• Disconnect air supply and depressurize all air linesconnected to this product before installation, servicing, orconversion.• Disconnect electrical supply before installation, servicingor conversion.• Operate within the manufacturer's specified pressure,temperature, voltage and other conditions listed in theseinstructions.• Medium must be moisture-free if ambient temperature isbelow freezing.• Service according to procedures listed on theseinstructions.• Installation, service and conversion of these products mustbe performed by knowledgeable personnel who understandhow pneumatic products are to be applied.• After installation, servicing, or conversion, air and electricalsupplies should be connected and the product tested forproper function and leakage. If audible leakage is present,or the product does not operate properly, do not put intouse.• Warnings and specifications on the product should not becovered by paint, etc. If masking is not possible, contactyour local representative for replacement labels.WARNING!Conversion Instructions: K583-092Manual Valves "OU" to O-Ring ISSUED: November, 1998Supersedes: July, 1995ECN #8982ASSEMBLY AND LUBRICATION Remove and discard items 4, 5, 6 and 7. Clean valve body (item 1) and stem (item 3) with mineral spirits to remove all foreign particles. Before reassembling, lightly lubricate valve body bore (item 1), valve stem (item 3)and o-rings (item 8) with Sunaplex 781 or an approved equivalent. Finish assembling valve as shown in Figure 2, with items 8 and 9 replacing discarded parts. When replacing end bearings (item 2) and stem stop bolt (not shown), the proper torque must be used. See charts below.TORQUE CHARTSStem Stop BoltEnd BearingsTYPICAL PART CHANGES Replace all internal parts with spacers and o-rings supplied in this kit.This is an interchangeable substitution. The o-ring design is a replacement for the "OU" packers, to improve performance.• Items 1, 2 and 3 to be reused.• Items 4, 5, 6 and 7 to be replaced with items 8 and 9.1Specially compounded o-rings, suitable fornon-lube service atreduced life.Pneumatic Division North America 8676 East M-89Richland, MI 49083High flow brass Figure 2O-Ring PackedPneumaticK583-092FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application, including consequences of any failure, and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met.The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR INCLUSION IN EQUIPMENT / MAINTENANCE INSTRUCTION MANUALS THAT UTILIZE THESE PRODUCTS. CONTACT YOUR LOCAL REPRESENTATIVE.WARNING!Pneumatic DivisionRichland, Michigan 49083269-629-5000PDNSG-1Safety Guide For Selecting And Using Pneumatic Division Products And Related AccessoriesWARNING:FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF PNEUMATIC DIVISION PRODUCTS, ASSEMBLIES OR RELATED ITEMS (“PRODUCTS”) CAN CAUSE DEATH, PERSONAL INJURY, AND PROPERTY DAMAGE. POSSIBLE CONSEQUENCES OF FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THESE PRODUCTS INCLUDE BUT ARE NOT LIMITED TO:• Unintended or mistimed cycling or motion of machine members or failure to cycle• Work pieces or component parts being thrown off at high speeds.• Failure of a device to function properly for example, failure to clamp or unclamp an associated item or device.• Explosion• Suddenly moving or falling objects.• Release of toxic or otherwise injurious liquids or gasses.Before selecting or using any of these Products, it is important that you read and follow the instructions below.1. GENERAL INSTRUCTIONS1.1. Scope: This safety guide is designed to cover general guidelines on the installation, use, and maintenance of Pneumatic Division Valves, FRLs (Filters, Pressure Regulators, and Lubricators), Vacuum products and related accessory components.1.2. Fail-Safe: Valves, FRLs, Vacuum products and their related components can and do fail without warning for many reasons. Design all systems and equipment in a fail-safe mode, so that failure of associated valves, FRLs or Vacuum products will not endanger persons or property.1.3 Relevant International Standards: For a good guide to the application of a broad spectrum of pneumatic fluid power devices see: ISO 4414:1998, Pneumatic Fluid Power – General Rules Relating to Systems. See for ordering information.1.4. Distribution: Provide a copy of this safety guide to each person that is responsible for selection, installation, or use of Valves, FRLs or Vacuum products. Do not select, or use Parker valves, FRLs or vacuum products without thoroughly reading and understanding this safety guide as well as the specific Parker publications for the products considered or selected.1.5. User Responsibility: Due to the wide variety of operating conditions and applications for valves, FRLs, and vacuum products Parker and its distributors do not represent or warrant that any particular valve, FRL or vacuum product is suitable for any specific end use system. This safety guide does not analyze all technical parameters that must be considered in selecting a product. The user, through its own analysis and testing, is solely responsible for:• Making the final selection of the appropriate valve, FRL, Vacuum component, or accessory.• Assuring that all user’s performance, endurance, maintenance, safety, and warning requirements are met and that the application presents no health or safety hazards.• Complying with all existing warning labels and / or providing all appropriate health and safety warnings on the equipment on which the valves, FRLs or Vacuum products are used; and,• Assuring compliance with all applicable government and industry standards.1.6. Safety Devices: Safety devices should not be removed, or defeated.1.7. Warning Labels: Warning labels should not be removed, painted over or otherwise obscured.1.8. Additional Questions: Call the appropriate Parker technical service department if you have any questions or require any additional information. See the Parker publication for the product being considered or used, or call 1-800-CPARKER, or go to , for telephone numbers of the appropriate technical service department.2. PRODUCT SELECTION INSTRUCTIONS2.1. Flow Rate: The flow rate requirements of a system are frequently the primary consideration when designing any pneumatic system. System components need to be able to provide adequate flow and pressure for the desired application.2.2. Pressure Rating: Never exceed the rated pressure of a product. Consult product labeling, Pneumatic Division catalogs or the instruction sheets supplied for maximum pressure ratings.2.3. Temperature Rating: Never exceed the temperature rating of a product. Excessive heat can shorten the life expectancy of a product and result in complete product failure.2.4. Environment: Many environmental conditions can affect the integrity and suitability of a product for a given application. Pneumatic Division products are designed for use in general purpose industrial applications. If these products are to be used in unusual circumstances such as direct sunlight and/or corrosive or caustic environments, such use can shorten the useful life and lead to premature failure of a product.2.5. Lubrication and Compressor Carryover: Some modern synthetic oils can and will attack nitrile seals. If there is any possibility of synthetic oils or greases migrating into the pneumatic components check for compatibility with the seal materials used. Consult the factory or product literature for materials of construction.2.6. Polycarbonate Bowls and Sight Glasses: To avoid potential polycarbonate bowl failures:• Do not locate polycarbonate bowls or sight glasses in areas where they could be subject to direct sunlight, impact blow, or temperatures outside of the rated range.• Do not expose or clean polycarbonate bowls with detergents, chlorinated hydro-carbons, keytones, esters or certain alcohols.• Do not use polycarbonate bowls or sight glasses in air systems where compressors are lubricated with fire resistant fluids such as phosphate ester and di-ester lubricants.!PDNSG-1Pneumatic Division Safety GuideISSUED: August 1 , 2006Supersedes: June 1, 2006Pneumatic Division Safety Guide2.7. Chemical Compatibility: For more information on plastic component chemical compatibility see Pneumatic Division technical bulletinsTec-3, Tec-4, and Tec-52.8. Product Rupture: Product rupture can cause death, serious personal injury, and property damage.• Do not connect pressure regulators or other Pneumatic Division products to bottled gas cylinders.• Do not exceed the maximum primary pressure rating of any pressure regulator or any system component.• Consult product labeling or product literature for pressure rating limitations.3. PRODUCT ASSEMBLY AND INSTALLATION INSTRUCTIONS3.1. Component Inspection: Prior to assembly or installation a careful examination of the valves, FRLs or vacuum products must beperformed. All components must be checked for correct style, size, and catalog number. DO NOT use any component that displays any signs of nonconformance.3.2. Installation Instructions: Parker published Installation Instructions must be followed for installation of Parker valves, FRLs andvacuum components. These instructions are provided with every Parker valve or FRL sold, or by calling 1-800-CPARKER, or at.3.3. Air Supply: The air supply or control medium supplied to Valves, FRLs and Vacuum components must be moisture-free if ambienttemperature can drop below freezing4. VALVE AND FRL MAINTENANCE AND REPLACEMENT INSTRUCTIONS4.1. Maintenance: Even with proper selection and installation, valve, FRL and vacuum products service life may be significantly reducedwithout a continuing maintenance program. The severity of the application, risk potential from a component failure, and experience with any known failures in the application or in similar applications should determine the frequency of inspections and the servicing or replacement of Pneumatic Division products so that products are replaced before any failure occurs. A maintenance program must be established and followed by the user and, at minimum, must include instructions 4.2 through 4.10.4.2. Installation and Service Instructions: Before attempting to service or replace any worn or damaged parts consult the appropriateService Bulletin for the valve or FRL in question for the appropriate practices to service the unit in question. These Service andInstallation Instructions are provided with every Parker valve and FRL sold, or are available by calling 1-800-CPARKER, or by accessing the Parker web site at .4.3. Lockout / Tagout Procedures: Be sure to follow all required lockout and tagout procedures when servicing equipment. For moreinformation see: OSHA Standard – 29 CFR, Part 1910.147, Appendix A, The Control of Hazardous Energy – (Lockout / Tagout)4.4. Visual Inspection: Any of the following conditions requires immediate system shut down and replacement of worn or damagedcomponents:• Air leakage: Look and listen to see if there are any signs of visual damage to any of the components in the system. Leakage is an indication of worn or damaged components.• Damaged or degraded components: Look to see if there are any visible signs of wear or component degradation.• Kinked, crushed, or damaged hoses. Kinked hoses can result in restricted air flow and lead to unpredictable system behavior.• Any observed improper system or component function: Immediately shut down the system and correct malfunction.• Excessive dirt build-up: Dirt and clutter can mask potentially hazardous situations.Caution: Leak detection solutions should be rinsed off after use.4.5. Routine Maintenance Issues:• Remove excessive dirt, grime and clutter from work areas.• Make sure all required guards and shields are in place.4.6. Functional Test: Before initiating automatic operation, operate the system manually to make sure all required functions operateproperly and safely.4.7. Service or Replacement Intervals: It is the user’s responsibility to establish appropriate service intervals. Valves, FRLs and vacuumproducts contain components that age, harden, wear, and otherwise deteriorate over time. Environmental conditions can significantly accelerate this process. Valves, FRLs and vacuum components need to be serviced or replaced on routine intervals. Service intervals need to be established based on:• Previous performance experiences.• Government and / or industrial standards.• When failures could result in unacceptable down time, equipment damage or personal injury risk.4.8. Servicing or Replacing of any Worn or Damaged Parts: To avoid unpredictable system behavior that can cause death, personalinjury and property damage:• Follow all government, state and local safety and servicing practices prior to service including but not limited to all OSHA Lockout Tagout procedures (OSHA Standard – 29 CFR, Part 1910.147, Appendix A, The Control of Hazardous Energy – Lockout / Tagout).• Disconnect electrical supply (when necessary) before installation, servicing, or conversion.• Disconnect air supply and depressurize all air lines connected to system and Pneumatic Division products before installation, service, or conversion.• Installation, servicing, and / or conversion of these products must be performed by knowledgeable personnel who understand how pneumatic products are to be applied.• After installation, servicing, or conversions air and electrical supplies (when necessary) should be connected and the product tested for proper function and leakage. If audible leakage is present, or if the product does not operate properly, do not put product orsystem into use.• Warnings and specifications on the product should not be covered or painted over. If masking is not possible, contact your localrepresentative for replacement labels.4.9. Putting Serviced System Back into Operation: Follow the guidelines above and all relevant Installation and Maintenance Instructionssupplied with the valve FRL or vacuum component to insure proper function of the system.。

派克矿用软管接头

80C-A04 80C-A04 80C-B04 80C-B04 80C-C04 80C-C04 80C-A05 80C-A05 80C-B05 80C-B05 80C-C05 80C-C05 80C-A06 80C-A06 80C-B06 80C-B06 80C-C06 80C-C06 83C-D06 83C-D06 80C-A08 80C-A08 80C-B08 80C-B08 80C-C08 80C-C08 83C-D08 83C-D08 80C-A10 80C-A10 80C-B10 80C-B10 80C-C10
3
4
目录
产品索引 ............................................................................................................6~9 矿用胶管和护套 .............................................................................................10~18
24
23,35 23,85
301SN-381
48
24
24,40 24,90
371-701
70
35
28,95 29,45
77C-772-774
71
35
27,95 28,45
15,9 16 -10 5/8 421HT-421SN-431-436-451TC-471ST-481 43
40
26,95 27,45
航空航天环境控制机电过滤流体与气体处理液压气动过程控制密封与屏蔽
矿山机械用胶管、 SteckO胶管接头和过渡接头

PISCO管接头

PV12
PV3/8
PV12 C
PV3/8 C
PPF16
PPF3/8
PPF16 C PPF3/8 C
PV16
PV1/2
PV16 C
PV1/2 C
PPF1/2
PPF1/2 C
PL
L 形弯头
øD T
型号
标准包装
PLøD-T
PLøD-TU
PL4-M5
PL5/32-U10U
PL4-M6
PL5/32-N0U
PL4-01
统一标准细牙螺纹
代码尺寸
U10 10-32UNF
* 如果（3）为管子尺寸，请从（2）中选择。
(4) 包装种类和接头的颜色
N1 NPT1/8
代码
包装分类
规格
释放环
公制尺寸
颜色
英寸尺寸
树脂壳体颜色
无代码
W
标准包装
标准
象牙白
黑
象牙白
白
白
黑
象牙白
美国标准锥管螺纹
N2
N3
NPT1/4
NPT3/8
N4 NPT1/2
新
追加型号
安全细则
在使用 PISCO 装置之前，请务必阅读第 14 至 16 页上的“安全说明”和“本手册所列产品通用安全说明”，以及第 18 至 19 页上的“快速装配接头通用安全说明”。
警告：1. 当允许使用的流体为水时，不要使用 PISCO 装置，除非此应用符合说明书中规定的所有条件。否则会对接头造成损坏，管子可能会脱落或造成泄漏。
镀镍铜 POM
(8)
(5) 管子
聚氨酯或尼龙净化室即用型
铄
PC6-02 PC6-03 PC8-01 PC8-02 PC8-03 PC10-01

帕克低压快速咬合连接件及软管说明书

Principle of Operation:Parker Autoclave Engineers Low Pressure “Speedbite” and “Mini” Series fittings are designed to work with 10V/SW Series and Mini Series Low Pressure Valves as well as Low Pressure Tubing made of commercially sized 316/316L SS in the “Annealed” condition. Pressures to 15,000 psi and sizes from 1/16" to 1/2" are readily available.The Speedbite connection is a single-ferrule bite-type compression fitting engineered for use with tubing designed by Parker Autoclave Engineers to a controlled hardness. Speedbite fittings employ a bite-type compression style single ferrule that is manually tightened.Low Pressure Fittings and Tubing Features:• Single-ferrule compression sleeve connections for up to 15,000 psi MAWP • Operating temperatures from -100°F (-73°C) to 650°F (343°C) • Fast easy 1-1/4 turn make-up of connection • Available sizes are 1/16", 1/8", 1/4", 3/8", and 1/2"• Fittings manufactured in accordance with ASME B31.3 Chapter IX standards with UNS S31600/S31603 dual rated 316/316L material cold worked to Parker Autoclave proprietary standards (optional material available).• Tubing manufactured to commercial OD tolerances ASTM A269 dual rated 316/316L material to a controlled hardness to facilitate proper ferrule bite.• Molybdenum disulfide-coated gland nuts to prevent gallingAll Parker Autoclave Engineers fittings are marked with manufacturers name, part number, material, heat code andmaximum pressure for complete traceability.Fittings and TubingLow Pressure "Speedbite",Single Ferrule to 15,000 psi (1034 bar)Includes Check Valves, Filters & CouplingsGland tting to compress Ferruleand ensure proper sealLow Pressure “Speedbite” design “bites” the tubingwith little or no tube distortionPrimary Sealing SurfaceSingle “Bite-Type” Ferrule SleeveAnnealed 316/316L Stainless Steel Tubing, to commercial OD tolerances2Fittings and Tubing: Low Pressure 02-0123SE 0818Fittings and TubingLow Pressure Fittings - Pressures to 15,000 psi (1034 bar)Each fitting or adapter use UNS S31600/31603 cold worked 316/316L Stainless Steel and are manufactured in accordance with ASME B31.3 Chapter IX standards. (Optional Materials available, contact factory for selection).(See “Technical Brochure” for Pressure/Temperature effect on temperatures above ambient.)Connection Components:All valves and fittings are supplied complete with appropriate glands and compression sleeves. To order these components separately, use order numbers listed. When using plug, ferrule sleeve is not required. Tubing pressure caps can be found in Adapter Brochure.Gland SMN ( )Ferrule SleeveSSL ( )PlugSP ( )( ) - Add Tube Size Code 1/8" - 20 1/4" - 40 3/8" - 60 1/2" - 80Example: 1/4" SW Series Gland - SMN40Note: Special material glands are normally supplied with four flats in place of standard hex.1/16" tubing system components are available in the mini-fitting series starting on page 6. 1/16" tubing components can be used in 10V Series valves and fittings if required.To ensure proper fit use Parker Autoclave Engineers tubing.NACE/ISO 15156 CompatibilityAll PAE Low Pressure “Speedbite” Fittings and Tubing can be made with materials suitable for NACE/ISO 15156 requirements. As per NACE and ISO-15156, it is contingent on the end user to select this material. As this compatibility limits the use of “cold worked” materials, pressure reduction in MAWP can be expected. Please consult our Technical Brochure where we identify the more popular annealed materials along with the pressure reduction. Our Sour Oil and Gas brochure has a more complete description of the available options for pressures up to 30,000 psi.NACE Suffix adder options:“-SOG ” suffix is used along with optional material to generate a hardness verification of pressure containing partsto generate a NACE certificate of compliance.3 Fittings and Tubing: Low Pressure 02-0123SE 08184Fittings and Tubing: Low Pressure 02-0123SE 08185 Fittings and Tubing: Low Pressure 02-0123SE 0818Fittings and TubingMini Series Fittings - Pressures to 15,000 psi (1034 bar)Connection Components:All valves and fittings are supplied complete with appropriate glands and compression sleeves. To order these components separately, use order numbers listed. When using plug, ferrule sleeve is not required.Gland SMN ( )Ferrule SleeveSSL ( )PlugSP ( )( ) - Add Tube Size Code 1/16" - 101/8" - 20Example:1/16" Gland Nut = SMN10 ( ) - Add Tube Size Code1/16" - 101/8" - 20Example:1/8" Ferrule Sleeve = SSL20( ) - Add Tube Size Code1/16" - 101/8" - 20Example:1/8" Plug = SP20Note: Special material glands are normally supplied with four flats in place of standard hex.(See “Technical Brochure” for Pressure/Temperature effect on temperatures above ambient.)6Fittings and Tubing: Low Pressure 02-0123SE 08187 Fittings and Tubing: Low Pressure 02-0123SE 08188Fittings and Tubing: Low Pressure 02-0123SE 08189Fittings and Tubing: Low Pressure 02-0123SE 0818Low Pressure Tubing - Pressures to 15,000 psi (1034 bar)Parker Autoclave Engineers offers a complete selection of annealed, seamless stainless steel tubing designed to match the performance standards of ParkerAutoclave Low Pressure valves and fittings. This tubing is manufactured of UNS S316/S31603, 316/316L Stainless Steel and furnished in random lengths between 20 feet (6 meters) and 26.5 feet (8 meters). In order to ensure proper sleeve “bite” into tubing, Parker Autoclave Engineers specifies and controls the strength and hardness levels of both the tube and sleeve materials.Inspection and Testing:Parker Autoclave Engineers annealed low pressure tubing is inspected for compliance with specified defect restrictions as well as carburization or inter-granular carbide precipitation. The tubing outside diameter and wall thickness is controlled within close tolerance to assure proper fit. Sample pieces of tube (for each lot) are tested to confirm mechanical proper-ties for proper compression sleeve “bite” and pressure capability. Furthermore, the sample tubes are pressure tested as a final check.Special Material:In addition to the type 316/316L stainless steel tubing in the annealed condition listed in this section, Parker Autoclave Engineers has a limited stock of hard-to-obtain shorter lengths of the following tubing materials:Monel*, Inconel 600*, Titanium Grade 2*,Hastelloy C276*, Inconel 625*, and Incoloy 825*(See Technical Catalog for additional information)Note: * Trademark names, Please consult factory for stock availabilty.NACE MR0175/ISO 15156 Options are available. Consult Factory.Tubing Tolerance:Tubing Details: 316/316L, UNS S31600/S31603 Stainless Steel (Annealed) to commercial OD sizing tolerances*Maximum pressure rating is based on the lowest rating of any component. Actual working pressure may be determined by tubing pressure rating, if lower. All dimensions for reference only and subject to change.For prompt service, Parker Autoclave Engineers stocks select products.Consult your local representative.Not for use as relief valve.)-BO suffix): 0° to 250°F (-18° to 121°C)-KO suffix): 30° to 500°F (-18° to 260°C)-TO suffix): -100° to 400°F (-73° to 204°C)-LTTO suffix): to -100°F (-73°C) Cracking Pressure: 20 psi (1.38 bar) ±30%. Springs for higher cracking pressures up to 100 psi available on special order for O-ring style check valves only.Installation: Vertical or Horizontal as required. Flow Direction Arrow marked on valve body.CAUTION: While testing has shown O-Rings to provide satisfactory service life, both cyclic and shelf life may vary widely with differing service conditions, properties of reactants, pressure and temperature cycling and age of the O-ring. FREQUENT INSPECTIONS SHOULD BE MADE to detect any deterioration, and O-rings replaced as required.(See “Technical Brochure” for Pressure/Temperature effect ontemperatures above ambient.)Material of Construction:O-Ring Check Valve Repair Kits:Check Valves are easily repaired. Add “R” to front of valvecatalog number for proper repair kit (example: RSWO8800)See “Cover Torque” on page 14 for re-assembly. Include anycatalog number suffix marked on original part when orderingrepair kit.10Fittings and Tubing: Low Pressure 02-0123SE 0818Prevent reverse flow where leak-tight shut-off is not mandatory. When differential drops below cracking pressure, valve closes. With all-metal components, valve can be used up to 650°F (343°C). See Technical Information section for connection temperature limitations. (Not for use as relief valve.)Ball and poppet are an integral design to assure positive,in-line seating without “chatter”. Poppet is designed essentially for axial flow with minimum pressure drop.Cracking Pressure: 20 psi (1.38 bar) +/- 30%Optional cracking pressures NOT available in Ball Style Check Valves Temperature: Minimum operating temperature for standard ball check valves 0°F (-17.8°C). For low temperature option to -100°F (-73°C) add suffix LT (Low temperature spring). Installation: Vertical or Horizontal as required. Flow Direction Arrow marked on valve body.NOTE: For optional material see Technical Brochure. Special material check valves are normally supplied with four flats in place of standard hex.(See “Technical Brochure” for Pressure/Temperature effect on temperatures above ambient.)Material of Construction:Basic Ball Check Valve Repair Kits:Check Valves are easily repaired. Add “R” to front of valvecatalog number for proper repair kit (example: RSWB6600)See “Cover Torque” on page 14 for re-assembly. Include anycatalog number suffix marked on original part when orderingrepair kit.11 Fittings and Tubing: Low Pressure 02-0123SE 0818Protects pressure gauges and pressure instrumentation fromsudden surges in flow or venting in the event of line failure.Vertical Installation: Since this type of check valveemploys a non-spring loaded ball, valve MUST be installed inVERTICAL position with arrow on valve body pointing UP.(cover gland up).Resetting Valve: Equalize the pressure across the ball.The ball will drop and reset automatically.Temperature: Operating temperature for standard ballexcess flow valves -100°F to 650°F (-73° to 343°C).(See “Technical Brochure” for Pressure/Temperature effect ontemperatures above ambient.)SWK Series Ball TypeExcess Flow ValvesMaterial of Construction:Ball Type Excess Flow Repair Kits:Excess Flow Valves are easily repaired. Add “R” to front ofvalve catalog number for proper repair kit.(example: RSWK8802)See “Cover Torque” on page 14 for re-assembly. Include anycatalog number suffix marked on original part when orderingrepair kit.12Fittings and Tubing: Low Pressure 02-0123SE 081813Fittings and Tubing: Low Pressure 02-0123SE 0818Protects pressure gauges and other pressure instrumentation from sudden surges in flow due to operator error or line failure. This valve provides dependable, tight shut-off.Vertical Installation : Since this type of check valveemploys a non-spring loaded poppet, valve MUST be installed in VERTICAL position with arrow on valve body pointing UP . (cover gland up).Resetting Valve: Equalize the pressure across the poppet.The poppet will drop and reset automatically.Temperature Ranges:Viton (FKM) O-ring (std.): 0° to 400°F (-18° to 204°C) Buna-N O-ring (-BO suffix): 0° to 250°F (-18° to 121°C) PTFE O-ring (-TO suffix): -100° to 400°F (-73° to 204°C)CAUTION: While testing has shown O-Rings to provide satisfactory service life, both cyclic and shelf life may vary widely with differing service conditions, properties of reactants, pres-sure and temperature cycling and age of the O-ring. FREQUENT INSPECTIONS SHOULD BE MADE to detect any deterioration, and O-rings replaced as required. CAUTION: See Tubing section for proper selection of tubing.(See “Technical Brochure” for Pressure/Temperature effect on temperatures above ambient.)SWKO Series O-Ring Type Excess Flow ValvesMaterial of Construction:O-Ring Excess Flow Valve Repair Kits:Excess Flow Valves are easily repaired. Add “R ” to front of valve catalog number for proper repair kit (example: RSWKO6600) See “Cover Torque” on page 14 for re-assembly. Include any catalog number suffix marked on original part when ordering repair kit.14Fittings and Tubing: Low Pressure 02-0123SE 0818: 316L Stainless Steel, Sintered Disc TypeDownstream/upstream micron size 35/65 is standard. 5/10 or Array 10/35 also available when specified. Other element combinationsavailable on special order.High Flow Cup-Type Line Filters are recommended in lowpressure systems requiring both high flow rates and maximumfilter surface area. Widely used in the industrial and chemicalprocessing fields, the cup design offers as much as six times theeffective filter area as compared to disc-type units. In addition,the filter elements can be quickly and easily replaced.Materials:Body, Cover, and Gland Nut - CW 316/316L Stainless Steel.Filter Element: 316L Stainless Steel, Sintered Cup Type.Standard elements available in choice of 5, 35 or 65 micronsizes. Note: Filter ratings are nominal.Spare Parts: Filter Elements are only replaceable part witheither filter type. See chart on page 14 for Filter Element partnumbers.Temperature Range:Both Models -100° to 650°F(-73° to 343°C). (See “Technical Brochure” for Pressure/Tempera-ture effect on temperatures above ambient.)NOTE 1: All filters furnished complete with connection components unlessotherwise specified. All dimensions for reference only and subject tochange. For optional materials, see Needle Valve Options sectionNOTE 2: Parker Autoclave Engineers disc and cup type filters are designedto filter small amounts of process particles. It is recommended that allfluids are thoroughly cleaned prior to entering the higher pressuresystem.NOTE 3: Special material filters are normally supplied with four flats in place ofstandard hex.NOTE 4: Pressure differential not to exceed 1,000 psi (69 bar) in a flowingcondition. Filter replacement is recommended.NOTE 5: Larger micron size filter element is installed on the upstream (inlet) side.15 Fittings and Tubing: Low Pressure 02-0123SE 081816Fittings and Tubing: Low Pressure 02-0123SE 081817 Fittings and Tubing: Low Pressure 02-0123SE 081818Fittings and Tubing: Low Pressure 02-0123SE 0818High PressureValves • Fittings • Tubingto 150,000 psi.Reactors • Vessels InstrumentationAir Driven, High Flow, High Pressure Liquid PumpsParker’s Motion & Control TechnologiesAt Parker, we’re guided by a relentless drive to help our customers become more productive and achieve higher levels of profitability by engineeringthe best systems for their requirements. It means looking at customer applications from many angles to find new ways to create value. Whateverthe motion and control technology need, Parker has the experience, breadth of product and global reach to consistently deliver. No company knows more about motion and control technology than Parker. For further information call 1-800-C-Parker.19Fittings and Tubing: Low Pressure 02-0123SE 0818! CAUTION !Do not mix or interchange component parts or tubing with those of other manufacturers. Doing so is unsafe and will void warranty.Parker Autoclave Engineers Valves, Fittings, and Tools are not designed to interface with common commercial instrument tubing and are designed to only connect with tubing manufactured toParker Autoclave Engineers AES specifications. Failure to do so is unsafe and will void warranty.Offer of SaleThe items described in this document are available for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. Any sale contract entered by Parker will begoverned by the provisions stated in Parker's standard terms and conditions of sale (copy available upon request).©2018 Parker Hannifin Corporation | Autoclave Engineers is a registered trademark of the Parker Hannifin Corporation Literature #: 02-0123SE August 2018ISO-9001 CertifiedInstrumentation Products Division Autoclave Engineers Operation 8325 Hessinger Drive Erie, PA 16509-4679Tel: 814 860 5700Fax: 814 860 /ipdInstrumentation Products Division Division Headquarters 1005 A Cleaner WayHuntsville, AL 35805 USA Tel: 256 881 2040Fax: 256 881 5072Parker Hannifin Manufacturing Ltd.Instrumentation Products Division, EuropeRiverside RoadPottington Business ParkBarnstaple, UK, EX31 1NP , UK Tel: 44 1271 313131Fax: 44 1271 373636WARNINGFAILURE, IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH,PERSONAL INJURY AND PROPERTY DAMAGE.This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The prod-ucts described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.Fittings and Tubing: Low Pressure 02-0123SE 0818Parker WorldwideNorth AmericaUSA – Corporate, Cleveland, OH Tel: +1 256 896 3000USA – IPD, Huntsville, AL Tel: +1 256 881 2040*****************USA – IPD, (Autoclave), Erie, PA Tel: +1 814 860 5700*******************CA – Canada, Grimsby, Ontario Tel +1 905-945-2274*********************South AmericaAR – Argentina, Buenos Aires Tel: +54 3327 44 4129 ******************BR – Brazil, Diadema, SP Diadema, SPTel: +55 11 4360 6700******************CL – Chile, Santiago Tel: +56 (0) 2 2303 9640******************MX – Mexico, Toluca Tel: +52 722 275 4200*******************Asia PacificAU – Australia, Dandenong Tel: +61 (0)2 9842 5150******************************CN – China, Shanghai Tel: +86 21 2899 5000*****************************HK – Hong Kong Tel: +852 2428 8008IN – India, MumbaiTel: +91 22 6513 7081-85ID – Indonesia, Tangerang Tel: +62 2977 7900********************JP – Japan, Tokyo Tel: +(81) 3 6365 4020******************KR – South Korea, Seoul Tel: +82 2 559 0400*******************MY – Malaysia, Selangor Tel: +603 784 90 800*******************SG – Singapore,Tel: +65 6887 6300*******************TH – Thailand, Bangkok Tel: +66 2 186 7000*********************TW – Taiwan, Taipei Tel: +886 2 2298 8987*************************VN – Vietnam, Hochi Minh City Tel: +848 382 508 56**********************Europe, Middle East, AfricaAE – UAE, Dubai Tel: +971 4 812 7100********************AT – Austria, Wiener Neustadt Tel: +43 (0)2622 23501-0*************************AT – Eastern Europe, Wiener Neustadt Tel: +43 (0)2622 23501 900****************************AZ – Azerbaijan, Baku Tel: +994 50 2233 458****************************BE/LU – Belgium, Nivelles Tel: +32 (0)67 280 900*************************BG – Bulgaria, Sofia Tel: +359 2 980 1344**************************BY – Belarus, Minsk Tel: +48 (0)22 573 24 00*************************CH – Switzerland, Etoy Tel: +41 (0) 21 821 87 00*****************************CZ – Czech Republic, Klecany Tel: +420 284 083 111*******************************DE – Germany, Kaarst Tel: +49 (0)2131 4016 0*************************DK – Denmark, Ballerup Tel: +45 43 56 04 00*************************ES – Spain, Madrid Tel: +34 902 33 00 01***********************FI – Finland, VantaaTel: +358 (0)20 753 2500*************************FR – France, Contamine s/Arve Tel: +33 (0)4 50 25 80 25************************GR – Greece, Athens Tel: +30 210 933 6450************************HU – Hungary, Budapest Tel: +36 223 885 470*************************IE – Ireland, DublinTel: +353 (0)1 466 6370*************************IT – Italy, Corsico (Ml)Tel: +39 02 45 19 21***********************KZ – Kazakhstan, Almaty Tel: +7 7273 561 000****************************NL – The Netherlands, Oldenzaal Tel: +31 (0)541 585 000********************NO – Norway, Stavanger Tel: +47 66 75 34 00************************PL – Poland, Warsaw Tel: +48 (0)22 573 24 00************************PT – Portugal, Leca da Palmeira Tel: +351 22 999 7360**************************RO – Romania, Bucharest Tel: +40 21 252 1382*************************RU – Russia, Moscow Tel: +7 495 645-2156************************SE – Sweden, Spånga Tel: +46 (0)8 59 79 50 00************************SK – Slovakia, Banská Bystrica Tel: +421 484 162 252**************************SL – Slovenia, Novo Mesto Tel: +386 7 337 6650**************************TR – Turkey, Istanbul Tel: +90 216 4997081************************UA – Ukraine, KievTel: +48 (0)22 573 24 00*************************UK – United Kingdom, Warwick Tel: +44 (0)1926 317 878********************ZA – South Africa, Kempton Park Tel: +27 (0)11 961 0700*****************************。

Parker Hannifin 品牌 P2 P3 系列 piston 气动泵维修手册说明书

1 P2-000-3400 2 P2-105-3200 3 P2-105-5003 4 P2-105-3000 5 P2-105-0209 6 P2-105-3203 7 P2-105-5010 8 P2-105-0214 9 P2-105-3102 10 P2-105-3001 11 P2-105-3202 12 P2-105-2400 13 P2-145-0201 14 P2-105-3925 15 P2-105-1020-01 16 P2-000-8950-16 17 P2-145-3101 1 18 P2-105-5008 19 P2-105-3303 20 P2-105-3902 21 P2-000-3900 0 22 39X10 23 210X134 24 210X208 25 210X283 5 27 299X124 28 256X248 29 256X543 30 256X559 31 256X575 32 256X579 33 2012 -9 34 2133 -9 35 2044 -7 36 2240 -7 37 2243 -7 38 2263 -7 39 3916 -9 40 108X2 41 P2-105-3300 41 P2-105-3304 42 P2-105-0212 43 P2-105-0223
1 IMPELLER RING - CCW
54 P2-105-0222-03
1 BARREL ASSEMBLY - CCW
MAX PRESSURE SETTING MINIMUM ADJUSTMENT - PB MAXIMUM ADJUSTMENT - PB MIN ADJUSTMENT - ALL OTHER MAX ADJUSTMENT - ALL OTHER
THRU-SHAFT

PARKER_接头基础解析

接头密封形式
密封形式
• 37°扩口
– 接头体、管套、螺母组成 – 硬管需预先扩口成37° – 在接头体前端和硬管的扩口处形成有效密(金属-金属) – Triple-Lok接头
接头密封形式
密封形式
• 45°扩口
– 接头体、螺母组成 – 硬管需预先扩口成45° – 在接头体前端和硬管的扩口处形成有效密(金属-金属) – Triple-Lok接头
*螺纹是接头的重要部分 *提供机械支持力和密封
接头解析接头螺纹-特征牙顶和牙底:
接头解析接头螺纹-特征
牙侧和牙型角:
接头解析接头螺纹-特征
牙形角和锥度:
螺纹角度
锥度
接头解析接头螺纹-特征
螺距：螺纹之间的距离
接头解析接头螺纹-特征
公制螺纹
常用接头公制螺纹螺距：1.0mm 、1.5mm、2.0mm
接头基础知识
接头基础知识
• • • • 什么是接头? 其功能是什么? 接头解析螺纹型式接头密封型式
什么是接头? 其功能是什么?
使用接头的目的：各种流体动力元件间的液压或气压管路的连接需要各种类型的接头。把管联接到液压系统上. 接头提供防渗漏密封和系统的接口
接头解析
油口端&管末端: 接头是一种连接流体动力系统元件的连接件，所有的接头除了堵头、堵帽之外，都至少有两个端口。
– 例：Ferulok, EO :卡套扣咬住(切入)管外壁，形成密封。
接头密封形式
密封形式
• 24°扣咬型(切入型) 续
– 例：EO-2: 功能螺母把弹性密封圈、金属定位环、卡套集合为一体 – 由功能螺母、接头体(可与EO互换)组成 – 弹性密封圈提供密封功能 – 定位环咬住(切入) 接头体(黄铜)、弹性管套、螺母(黄铜) – 螺母挤压管外径上的弹性密封管套，形成密封 – 应用于高压时，可对管进行扩口

派克扩口式管接头样本Parker JIC Fitting

Triple-Lok®The universal37° ﬂ ared ﬁ ttingTriple-Lok®Visual indexTube to tubeBulkhead unionTube tomale NPTFTube tomale BSPTTube tomale BSPPTube to straightthread UNFTube tomale metricISO 6149-3Tube tomale metricDIN 3852-1Tube tofemale NPTFHMTX EMTX JMTX KTXp. K9 p. K10 p. K11 p. K14WMTX WEMTX WNTX WJTX WJJTX WLNMp.K15 p.K16 p.K17 p.K18 p.K19 p.K92FMTX CMTXC CTX CCCTX VMTX RMTX SMTXp.K36 p.K51 p.K52 p.K53 p.K59 p.K71 p.K65F3MX C3MX V3MX R3MX S3MXp.K37 p.K54 p.K60 p.K72 p.K66F4OMX F42EDMX C4OMX V4OMX R4OMX S4OMXp.K33 p.K32 p.K49 p.K57 p.K69 p.K63F5OMX FF5OMX C5OMX CC5OX V5OMX R5OMX S5OMX p.K29 p.K31 p.K47 p.K48 p.K56 p.K68 p.K62F87OMX C87OMX V87OMX R87OMX S87OMXp.K28 p.K46 p.K55 p.K67 p.K61F8OMX F82EDMX C8OMX V8OMX R8OMX S8OMXp.K35 p.K34 p.K50 p.K58 p.K70 p.K64GMTX WGMTX DMTX OTX MTX G6Xp.K74 p.K75 p.K76 p.K77 p.K78 p.K79KTriple-Lok ®Triple-Lok®KTriple-Lok ®BTX NutTriple-Lok ® 37° Flare end nut SAE 070110 MS51531Tube Thread Weight O.D. UN/UNF-2B C D L (steel) Triple-Lok ® Triple-Lok ® Triple-Lok ® mm in. T6 in. mm mm g/1 piece Steel Stainless Steel Brass 1/8 5/16-24 3/8 5 14 6 2 BTX-S 2 BTX-SS2 BTX-B 3/16 3/8-24 7/16 6 16 83 BTX-S 3 BTX-SS 3 BTX-B 6 1/4 7/16-20 9/16 8 16 11 4 BTX-S 4 BTX-SS 4 BTX-B 8 5/16 1/2-20 5/8 10 17 145 BTX-S 5 BTX-SS 5 BTX-B 10 3/8 9/16-18 11/16 11 18 18 6 BTX-S 6 BTX-SS 6 BTX-B 12 1/2 3/4-16 7/8 15 22 29 8 BTX-S 8 BTX-SS 8 BTX-B 14, 15, 16 5/8 7/8-14 1 18 25 54 10 BTX-S 10 BTX-SS 10 BTX-B 18, 20 3/4 1 1/16-12 1 1/4 21 26 73 12 BTX-S 12 BTX-SS 12 BTX-B 22 7/8 1 3/16-12 1 3/8 24 28 100 14 BTX-S 14 BTX-SS 14 BTX-B 25 1 1 5/16-12 1 1/2 28 29 104 16 BTX-S 16 BTX-SS 16 BTX-B 28, 30, 32 1 1/4 1 5/8-12 2 34 31 240 20 BTX-S 20 BTX-SS 20 BTX-B 35, 38 1 1/2 1 7/8-12 2 1/4 41 36 325 24 BTX-S 24 BTX-SS 24 BTX-B2 2 1/2-12 2 7/8 55 45 549 32 BTX-S32 BTX-SSOrder codes shown are part of our current manufacturing programme.Triple-Lok®BMTX NutTriple-Lok® 37° Flare end nutSAE 070110Tube Thread WeightO.D. UN/UNF-2B C D L (steel) Triple-Lok® Triple-Lok®Steelpiece Steel Stainless mm in. T6 mm mm mm g/16 1/4 7/16-20 14 8 16 11 4BMTXS 4BMTXSS8 5/16 1/2-20 17 10 17 14 5BMTXS 5BMTXSS10 3/8 9/16-18 19 11 18 18 6BMTXS 6BMTXSS12 1/2 3/4-16 22 15 21 29 8BMTXS 8BMTXSS14, 15, 16 5/8 7/8-14 27 18 25 42 10BMTXS 10BMTXSS 18, 20 3/4 1 1/16-12 32 22 26 73 12BMTXS 12BMTXSS5/16-12 41 28 28 104 16BMTXS 16BMTXSS25 1 128, 30, 32 1 1/4 1 5/8-12 50 34 31 240 20BMTXS 20BMTXSS 35, 38 1 1/2 1 7/8-12 60 41 36 325 24BMTXS 24BMTXSS42 21/4 65 48 40 437 28BMTXS 28BMTXSSOrder codes shown are part of our current manufacturing programme.KTriple-Lok ®Tube WeightO.D. L X (steel) Triple-Lok ® Triple-Lok ® Triple-Lok ®mm mm mm g/1 piece Steel Stainless Steel Brass 6 10 10 2 TXS6 TXSS6 TXB6 8 11 11 2 TXS8 TXSS8 TXB8 10 13 13 2 TXS10 TXSS10 TXB10 12 14 17 7 TXS12 TXSS12 TXB12 14 17 20 13 TXS14 TXSS14 TXB14 15 17 20 10 TXS15 TXSS15 TXB15 16 17 20 7 TXS16 TXSS16 TXB16 18 17 25 16 TXS18 TXSS18 TXB18 20 17 25 12 TXS20 TXSS20 TXB20 22 19 28 25 TXS22 TXSS22 TXB22 25 20 31 21 TXS25 TXSS25 TXB25 28 23 39 40 TXS28 TXSS28 TXB28 30 23 39 45 TXS30 TXSS30 TXB30 32 23 39 30 TXS32 TXSS32 TXB32 35 28 45 60 TXS35 TXSS35 TXB35 38 28 45 51 TXS38 TXSS38 TXB38 422955149TXS42 TXSS42 TXB42Order codes shown are part of our current manufacturing programme.TX SleeveTriple-Lok ® 37° Flare tube end sleeve for metric tubes SAE 070105Triple-Lok ®Tube WeightO.D. L X (steel) T riple-Lok ® Triple-Lok ® Triple-Lok ® in. mm mm g/1 piece Steel Stainless Steel Brass 1/8 9 7 22 TX-S 2 TX-SS 2 TX-B 3/169823 TX-S 3 TX-SS 3 TX-B 1/4 10 10 2 4 TX-S 4 TX-SS 4 TX-B 5/16 11 11 25 TX-S 5 TX-SS 5 TX-B 3/8 13 13 36 TX-S 6 TX-SS 6 TX-B 1/2 14 17 68 TX-S 8 TX-SS 8 TX-B 5/8 17 20 8 10 TX-S 10 TX-SS 10 TX-B 3/4 17 25 13 12 TX-S 12 TX-SS 12 TX-B 7/8 19 28 18 14 TX-S 14 TX-SS 14 TX-B 1 20 31 23 16 TX-S 16 TX-SS 16 TX-B 1 1/4 23 39 30 20 TX-S 20 TX-SS 20 TX-B 1 1/2 28 45 51 24 TX-S 24 TX-SS 24 TX-B 2306115632 TX-S32 TX-SS32 TX-BOrder codes shown are part of our current manufacturing programme.TX SleeveTriple-Lok ® 37° Flare tube sleeve SAE 070105 MS51533KTriple-Lok ®Tube 1 Tube 2 Thread Thread Weight PN (bar)O.D. O.D. UN/UNF-2A UN/UNF-2A C D D1 L1 (steel) Triple-Lok ® Triple-Lok ® Triple-Lok ®mm in. mm in. T1 T2 mm mm mm mm g/1 piece Steel Stainless Steel Brass S SS1/8 1/8 5/16-24 5/16-24 11 2 2 30 9 2 HTX-S 500 —3/16 3/16 3/8-24 3/8-24 11 3 3 31 10 3 HTX-S 500 — 6 1/4 6 1/4 7/16-20 7/16-20 13 4 4 35 16 4HMTXS 4HMTXSS 4HMTXB 500 350 6 1/4 1/8 7/16-20 5/16-24 13 5 2 32 12 4-2 HTX-S 4-2HMTXSS 4-2HMTXB 500 350 6 1/4 3/16 7/16-20 3/8-24 13 5 3 33 14 4-3 HTX-S 4-3HMTXSS 4-3HMTXB 500 350 8 5/16 8 5/16 1/2-20 1/2-20 14 6 6 35 18 5HMTXS 5HMTXSS 5HMTXB 420 350 8 5/16 6 1/4 1/2-20 7/16-20 14 6 5 35 18 5-4 HTX-S 5-4HMTXSS 5-4HMTXB 420 350 10 3/8 10 3/8 9/16-18 9/16-18 17 8 8 36 25 6HMTXS 6HMTXSS 6HMTXB 420 350 10 3/8 6 1/4 9/16-18 7/16-20 17 8 4 36 22 6-4HMTXS 6-4HMTXSS 6-4HMTXB 420 350 10 3/8 8 5/16 9/16-18 1/2-20 17 8 6 36 25 6-5 HTX-S 6-5HMTXSS 6-5HMTXB 420 350 12 1/2 12 1/2 3/4-16 3/4-16 19 10 10 41 52 8HMTXS 8HMTXSS 8HMTXB 420 350 12 1/2 6 1/4 3/4-16 7/16-20 21 10 5 39 45 8-4 HTX-S 8-4HMTXSS 8-4HMTXB 420 350 12 1/2 10 3/8 3/4-16 9/16-18 19 10 8 39 45 8-6HMTXS 8-6HMTXSS 8-6HMTXB 420 350 14, 15,16 5/8 14, 15,16 5/8 7/8-14 7/8-14 24 12 12 48 80 10HMTXS 10HMTXSS 10HMTXB 350 350 14, 15,16 5/8 10 3/8 7/8-14 9/16-18 24 13 8 43 60 10-6HMTXS 10-6HMTXSS 10-6HMTXB 350 350 14, 15,16 5/8 12 1/2 7/8-14 3/4-16 24 12 10 45 68 10-8HMTXS 10-8HMTXSS 10-8HMTXB 350 350 18, 20 3/4 18, 20 3/4 1 1/16-12 1 1/16-12 27 16 16 55 125 12HMTXS 12HMTXSS 12HMTXB 350 350 18, 20 3/4 12 1/2 1 1/16-12 3/4-16 29 16 10 50 101 12-8 HTX-S 12-8HMTXSS 12-8HMTXB 350 350 20 3/4 14, 15,16 5/8 1 1/16-12 7/8-14 29 16 12 52 113 12-10HMTXS 12-10HMTXSS 12-10HMTXB 350 350 22 7/8 22 7/8 1 3/16-12 1 3/16-12 32 18 18 56 156 14 HTX-S 14HMTXSS 14HMTXB 280 280 25 1 25 1 1 5/16-12 1 5/16-12 36 22 22 57 131 16HMTXS 16HMTXSS 16HMTXB 280 280 25 1 20 3/4 1 5/16-12 1 1/16-12 36 22 16 56 169 16-12HMTXS 16-12HMTXSS 16-12HMTXB 280 280 28, 30, 32 1 1/4 28, 30, 32 1 1/4 1 5/8-12 1 5/8-12 46 28 28 62 271 20HMTXS 20HMTXSS 20HMTXB 280 210 28, 30, 32 1 1/4 25 1 1 5/8-12 1 5/16-12 46 28 22 61 235 20-16HMTXS 20-16HMTXSS 20-16HMTXB 280 210 35, 38 1 1/2 35, 38 1 1/2 1 7/8-12 1 7/8-12 50 33 33 70 382 24HMTXS 24HMTXSS 24HMTXB 210 210 42 42 2 1/4-12 2 1/4-12 60 39 39 71 469 28HMTXS 28HMTXSS 28HMTXB 140 150 2 2 2 1/2-12 2 1/2-12 67 45 45 87 785 32 HTX-S 32HMTXSS 32HMTXB 140 150Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.PN (bar)= PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.For Brass parts reduce pressures by 35%.HMTX UnionTriple-Lok ® 37° Flare ends SAE 070101 MS51501Triple-Lok®EMTX Union elbowTriple-Lok® 37° Flare endsSAE 070201 MS51505(bar) Tube Thread Thread Weight PNY(steel)Triple-Lok® Triple-Lok® Triple-Lok®M1MUN/UNF2-ADD1O.D. UN/UNF-2Amm in. T T1 mm in. mm mm mm g/1 piece Steel Stainless Steel Brass S SS 1/8 5/16-24 5/16-24 2 2 20 20 11 18 2 ETX-S 500—— 3/16 3/8-24 3/8-24 3 3 21 21 11 20 3 ETX-S 500500 3506 1/4 7/16-20 7/16-20 4 4 23 23 11 25 4EMTXS 4EMTXSS 4ETX-B420 350ETX-B8 5/16 1/2-20 1/2-20 6 6 24 24 13 32 5EMTXS 5EMTXSS 5420 35010 3/8 9/16-18 9/16-18 8 8 27 27 14 44 6EMTXS 6EMTXSS 6ETX-B10 3/8 9/16-18 7/16-20 8 4 27 27 14 40 6-4 ETX-S 6-4EMTXSS 6-4 ETX-B 420 350420 350ETX-B12 1/2 3/4-16 3/4-16 10 10 32 32 19 88 8EMTXS 8EMTXSS 812 1/2 3/4-16 3/8-24 10 8 32 29 19 75 8-6 ETX-S 8-6EMTXSS 420 —350 350ETX-B 15,16 5/8 7/8-14 7/8-14 12 12 37 37 22 139 10EMTXS 10EMTXSS 1014,15,16 5/8 7/8-14 3/4-16 12 10 37 34 22 120 10-8 ETX-S 10-8EMTXSS 10-8 ETX-B 350 35014,ETX-B350 3501/16-12 16 16 42 42 27 258 12EMTXS 12EMTXSS 121/16-12 118,20 3/4 11/16-12 3/4-16 16 10 42 46 27 220 12-8 ETX-S 12-8EMTXSS 350 —20 3/4 118,1/16-12 7/8-14 16 12 42 39 27 240 12-10 ETX-S 12-10EMTXSS 350 —20 3/4 118,3/16-12 18 18 44 44 30 273 14 ETX-S 14EMTXSS 280 —22 7/8 13/16-12 1ETX-B280 2805/16-12 22 22 46 46 33 333 16EMTXS 16EMTXSS 165/16-12 125 1 122,5/16-12 11/16-12 22 16 46 45 33 310 16-12 ETX-S 16-12EMTXSS 16-12 ETX-B 280 28025 1 122,ETX-B280 21028, 30, 32 1 1/4 1 5/8-12 1 5/8-12 28 28 52 52 41 586 20EMTXS 20EMTXSS 20210 140ETX-B 35, 38 1 1/2 1 7/8-12 1 7/8-12 33 33 59 59 48 778 24EMTXS 24EMTXSS 24—1/4-12 21/4-12 39 39 74 74 63 1100 28 ETX-S 140 3/4 242 1—1/2-12 45 45 78 78 64 1680 32 ETX-S 1402 21/2-12 2Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.PN (bar)= PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.For Brass parts reduce pressures by 35%.KKKTX Union crossTriple-Lok® 37° Flare end (four ends)SAE 070501 MS51517Tube Thread Weight PN(bar)Triple-Lok® Triple-Lok® Triple-Lok®(steel)O.D. UN/UNF-2AD M YSSSteel Brass Spiece Steel Stainless mm in. T mm mm mm g/11/4 7/16-20 4 23 11 41 4 KTX-S 4 KTX-SS 4 KTX-B 500 35065/16 1/2-20 6 24 14 50 5 KTX-S 5 KTX-SS 5 KTX-B 420 350810 3/8 9/16-18 8 27 14 68 6 KTX-S 6 KTX-SS 6 KTX-B 420 35012 1/2 3/4-16 10 32 19 144 8 KTX-S 8 KTX-SS 8 KTX-B 420 35014, 15,16 5/8 7/8-14 12 37 22 220 10 KTX-S 10 KTX-SS 10 KTX-B 350 350 18, 20 3/4 1 1/16-12 16 42 27 345 12 KTX-S 12 KTX-SS 12 KTX-B 350 350 5/16-12 22 46 33 588 16 KTX-S 16 KTX-SS 16 KTX-B 280 28025 1 1Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.PN (bar)= PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.For Brass parts reduce pressures by 35%.KMaximum bulkhead wallthicknessTube O.D. Straight bulkhead unionShape bulkhead unionMax. thicknessMax. thicknessSize inch metric mmmm4 1/4 6 8.4 5.35 5/16 8 8.4 5.3 6 3/8 10 10.7 7.18 1/2 12 11.2 8.4 10 5/8 14–16 10.9 8.1 12 3/4 18–2011.2 8.6 14 7/8 10.4 7.9 16 1 22–25 9.9 7.4 20 1 1/4 28–32 10.2 7.4 24 1 1/235–387.1 — 3227.1—WMTX Bulkhead unionTriple-Lok ® 37° Flare ends SAE 070601 MS51520Tube Thread WeightPN (bar) O.D. UN/UNF-2A C2 D I1 L4 (steel) Triple-Lok ® Triple-Lok ® Triple-Lok ®mm in. T mm mm mm mm g/1 piece Steel Stainless Steel BrassS SS6 1/4 7/16-20 17 4 31 53 41 4WMTXWLNMS 4WMTXWLNMSS 4WMTXWLNMB 500 3508 5/16 1/2-20 19 6 31 53 49 5WMTXWLNMS 5WMTXWLNMSS 5WMTXWLNMB 420 350 10 3/8 9/16-18 22 8 33 55 64 6WMTXWLNMS 6WMTXWLNMSS 6WMTXWLNMB 420 350 12 1/2 3/4-16 24 10 37 62 111 8WMTXWLNMS 8WMTXWLNMSS 8WMTXWLNMB 420 350 14, 15,16 5/8 7/8-14 30 12 40 70 157 10WMTXWLNMS 10WMTXWLNMSS 10WMTXWLNMB 350 350 18, 20 3/4 1 1/16-12 36 16 44 79 254 12WMTXWLNMS 12WMTXWLNMSS 12WMTXWLNMB 350 350 22 7/8 1 3/16-12 38 18 45 80 296 14 WTX-WLN-S 14WMTXWLNMSS 14WMTXWLNMB 280 280 25 1 1 5/16-12 41 22 44 80 337 16WMTXWLNMS 16WMTXWLNMSS 16WMTXWLNMB 280 280 28, 30, 32 1 1/4 1 5/8-12 50 28 46 84 462 20WMTXWLNMS 20WMTXWLNMSS 20WMTXWLNMB 280 210 35, 38 1 1/2 1 7/8-12 55 33 46 89 695 24WMTXWLNMS 24WMTXWLNMSS 24WMTXWLNMB 210 140Order codes shown are part of our current manufacturing programme. Imperial and metric parts may vary in hexagon dimensions.For the version without the locknut remove “WLNM” (e. g. 16WMTX)PN (bar)= PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.For Brass parts reduce pressures by 35%.WEMTX Bulkhead union elbowTriple-Lok® 37° Flare endsSAE 070701 MS51507(bar) Tube Thread Weight PNM4YM3(steel) Triple-Lok® Triple-Lok® Triple-Lok®I2C2O.D. UN/UNF-2ADmm in. T mm mm mm mm mm mm g/1 piece Steel Stainless Steel Brass S SS6 1/4 7/16-20 17 4 26 25 40 11 44 4 WETX-WLN-S 4 WETX-WLN-SS 4 WETX-WLN-B 500 3508 5/16 1/2-20 19 6 26 27 44 13 59 5 WETX-WLN-S 5 WETX-WLN-SS 5 WETX-WLN-B 420 35010 3/8 9/16-18 22 8 28 28 46 14 72 6WEMTXWLNMS 6 WETX-WLN-SS 6 WETX-WLN-B 420 35012 1/2 3/4-16 24 10 32 36 54 19 145 8WEMTXWLNMS 8 WETX-WLN-SS 8 WETX-WLN-B 420 350 14,15,16 5/8 7/8-14 30 12 35 40 61 22 212 10WEMTXWLNMS 10 WETX-WLN-SS 10 WETX-WLN-B 350 350 1/16-12 36 16 40 45 68 27 345 12WEMTXWLNMS 12 WETX-WLN-SS 12 WETX-WLN-B 350 35020 3/4 118,3/16-12 38 18 40 49 71 33 370 14 WETX-WLN-S 14 WETX-WLN-SS 280 —22 7/8 15/16-12 41 22 40 49 71 33 474 16 WETX-WLN-S 16 WETX-WLN-SS 280 —25 1 128, 30, 32 1 1/4 1 5/8-12 48 28 41 55 80 41 753 20 WETX-WLN-S 20 WETX-WLN-SS 280 —Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.For the version without the locknut remove “WLNM” (e. g. 16WETX)PN (bar)= PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.For Brass parts reduce pressures by 35%.Maximum bulkhead wallthicknessTube O.D. Straight bulkhead union Shape bulkhead unionMax. thickness Max. thicknessSize inch metric mm mm4 1/4 6 8.4 5.35 5/16 8 8.4 5.36 3/8 10 10.7 7.18 1/2 12 11.2 8.410 5/8 14–16 10.9 8.112 3/4 18–20 11.2 8.614 7/8 10.4 7.916 1 22–25 9.9 7.41/4 28–32 10.2 7.420 11/2 35–38 7.1 —24 132 2 7.1 —KMaximum bulkhead wallthicknessTube O.D. Straight bulkhead unionShape bulkhead unionMax. thicknessMax. thicknessSize inch metric mmmm4 1/4 6 8.4 5.35 5/16 8 8.4 5.3 6 3/8 10 10.7 7.18 1/2 12 11.2 8.4 10 5/8 14–16 10.9 8.1 12 3/4 18–2011.2 8.6 14 7/8 10.4 7.9 16 1 22–25 9.9 7.4 20 1 1/4 28–32 10.2 7.4 24 1 1/235–387.1 — 3227.1—WNTX 45° Bulkhead union elbowTriple-Lok ® 37° Flare ends SAE 070801 MS51509Tube Thread WeightPN (bar) O.D. UN/UNF-2A C2 D I2 M2 M9 Y (steel) Triple-Lok ® Triple-Lok ®mm in. T mm mm mm mm mm mm g/1 piece Steel Stainless Steel S SS6 1/4 7/16-20 17 4 26 18 39 11 324 WNTX-WLN-S 4 WNTX-WLN-SS 500 350 8 5/16 1/2-20 19 6 26 20 42 14 415 WNTX-WLN-S 420 —10 3/8 9/16-18 21 8 28 21 42 14 48 6 WNTX-WLN-S 6 WNTX-WLN-SS 420 350 12 1/2 3/4-16 25 10 32 25 49 19 105 8 WNTX-WLN-S 8 WNTX-WLN-SS 420 350 14, 15,16 5/8 7/8-14 29 12 35 28 55 22 152 10 WNTX-WLN-S 10 WNTX-WLN-SS 350 350 18, 20 3/4 1 1/16-12 35 16 40 33 62 27 245 12 WNTX-WLN-S 12 WNTX-WLN-SS 350 350 22, 25 1 1 5/16-12 41 22 40 37 65 33 355 16 WNTX-WLN-S 16 WNTX-WLN-SS 280 28028, 30, 321 1/41 5/8-12 48 28 41 40 67 4146520 WNTX-WLN-S280 —Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.For the version without the locknut remove “WLN” (e.g. 16 WNTX)PN (bar)= PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.Maximum bulkhead wallthicknessTube O.D. Straight bulkhead unionShape bulkhead unionMax. thicknessMax. thicknessSize inch metric mmmm4 1/4 6 8.4 5.35 5/16 8 8.4 5.3 6 3/8 10 10.7 7.18 1/2 12 11.2 8.4 10 5/8 14–16 10.9 8.1 12 3/4 18–2011.2 8.6 14 7/8 10.4 7.9 16 1 22–25 9.9 7.4 20 1 1/4 28–32 10.2 7.4 24 1 1/235–387.1 — 3227.1—WJTX Bulkhead branch teeTriple-Lok ® 37° Flare ends SAE 070959 MS51515Tube Thread WeightPN (bar) O.D. UN/UNF-2A C2 D I2 M3 M4 Y (steel) Triple-Lok ® Triple-Lok ®mm in. T mm mm mm mm mm mm g/1 piece Steel Stainless Steel S SS6 1/4 7/16-20 17 4 26 25 40 11 454 WJTX-WLN-S 4 WJTX-WLN-SS 500 35010 3/8 9/16-18 21 8 28 28 46 14 71 6 WJTX-WLN-S 6 WJTX-WLN-SS 420 350 12 1/2 3/4-16 25 10 32 35 54 19 158 8 WJTX-WLN-S 8 WJTX-WLN-SS 420 350 14, 15,16 5/8 7/8-14 29 12 35 40 61 22 297 10 WJTX-WLN-S 10 WJTX-WLN-SS 350 350 18, 20 3/4 1 1/16-12 35 16 40 45 68 27 379 12 WJTX-WLN-S 12 WJTX-WLN-SS 350 35022, 25 1 1 5/16-12 42 22 40 49 71 33 420 16 WJTX-WLN-S 280 — 28, 30, 321 1/41 5/8-12 48 28 41 55 79 4150020 WJTX-WLN-S280 —Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.For the version without the locknut remove “WLN” (e.g. 16 WJTX)PN (bar)= PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.KMaximum bulkhead wallthicknessTube O.D. Straight bulkhead unionShape bulkhead unionMax. thicknessMax. thicknessSize inch metric mmmm4 1/4 6 8.4 5.35 5/16 8 8.4 5.3 6 3/8 10 10.7 7.18 1/2 12 11.2 8.4 10 5/8 14–16 10.9 8.1 12 3/4 18–2011.2 8.6 14 7/8 10.4 7.9 16 1 22–25 9.9 7.4 20 1 1/4 28–32 10.2 7.4 24 1 1/235–387.1 — 3227.1—WJJTX Bulkhead run teeTriple-Lok ® 37° Flare ends SAE 070958 MS51516Tube Thread Weight O.D. UN/UNF-2A C2 D I2 M3 M4 Y (steel) Triple-Lok ® PN mm in. T mm mm mm mm mm mm g/1 piece Steel (bar)6 1/4 7/16-20 17 4 26 25 40 11584 WJJTX-WLN-S 50010 3/8 9/16-18 21 8 28 28 46 14756 WJJTX-WLN-S 420 12 1/2 3/4-16 25 10 32 35 54 19 158 8 WJJTX-WLN-S 420 14, 15,16 5/8 7/8-14 29 12 35 40 61 22 309 10 WJJTX-WLN-S 350 18, 20 3/4 1 1/16-12 35 16 40 45 68 27 340 12 WJJTX-WLN-S 350 22, 25 1 1 5/16-12 42 22 40 49 71 36 390 16 WJJTX-WLN-S 280 28, 30, 32 1 1/4 1 5/8-1248 28 41 55 79 4145020 WJJTX-WLN-S280Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.For the version without the locknut remove “WLN” (e.g. 16 WJJTX)PN (bar)= PN (MPa)10Tube Thread Thread Weight PN (bar)O.D. UN/UNF-2A UN/UNF-2B C3 D M M5 M10 Y (steel) Triple-Lok ® Triple-Lok ®mm in. T T6 mm mm mm mm mm mm g/1 piece Steel Stainless Steel S SS 3/16 3/8-24 3/8-24 13 3 21 25 16 11273 C6X-S 500 — 6 1/4 7/16-20 7/16-20 16 4 23 25 17 11 37 4C6MXS 4C6MXSS 500 350 8 5/16 1/2-20 1/2-20 17 6 24 27 17 13 43 5C6MXS 5C6MXSS 420 350 10 3/8 9/16-18 9/16-18 19 8 27 32 22 14 54 6C6MXS 6C6MXSS 350 350 12 1/2 3/4-16 3/4-16 22 10 32 35 24 19 105 8C6MXS 8C6MXSS 350 350 14, 15,16 5/8 7/8-14 7/8-14 27 12 37 41 28 22 162 10C6MXS 10C6MXSS 350 350 18, 20 3/4 1 1/16-12 1 1/16-12 32 16 42 44 30 27 260 12C6MXS 12C6MXSS 350 350 22 7/8 1 3/16-12 1 3/16-12 35 18 46 45 34 33 293 14 C6X-S 250 — 25 1 1 5/16-12 1 5/16-12 38 22 46 51 36 33 420 16C6MXS 16C6MXSS 250 250 28, 30, 32 1 1/4 1 5/8-12 1 5/8-12 50 28 52 59 43 41 679 20 C6X-S 20C6MXSS 250 210 35, 38 1 1/2 1 7/8-12 1 7/8-12 57 33 59 66 47 48 747 24 C6X-S 24C6MXSS 170 140 22 1/2-12 2 1/2-12 73 45 78 89 62 6692032 C6X-S 110 —Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.PN (bar)= PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.C6MX Swivel nut elbowTriple-Lok ® 37° Flare end / Triple-Lok ® 37° Flare female swivel end SAE 070221 MS51521KTube Thread Thread Weight PN (bar) O.D. UN/UNF-2A UN/UNF-2B C3 D M2 M6 M11 Y (steel) Triple-Lok ® Triple-Lok ®mm in. T T6 mm mm mm mm mm mm g/1 piece Steel Stainless Steel S SS 6 1/4 7/16-20 7/16-20 14 4 18 24 15 11 30 4 V6X-S 4 V6X-SS 500 350 8 5/16 1/2-20 1/2-20 16 6 20 25 16 14 45 5 V6X-S 5 V6X-SS 420 350 10 3/8 9/16-18 9/16-18 19 8 21 28 19 14 47 6 V6X-S 6 V6X-SS 350 350 12 1/2 3/4-16 3/4-16 22 10 25 33 22 19 89 8V6MXS 8 V6X-SS 350 350 14, 15,16 5/8 7/8-14 7/8-14 27 12 28 37 24 22 131 10 V6X-S 10 V6X-SS 350 350 18, 20 3/4 1 1/16-12 1 1/16-12 32 16 33 38 24 27 203 12 V6X-S 12 V6X-SS 350 350 22 7/8 1 3/16-12 1 3/16-12 35 18 35 41 28 30 291 14 V6X-S 250 — 25 1 1 5/16-12 1 5/16-12 38 22 37 44 29 33 335 16 V6X-S 16 V6X-SS 250 250 28, 30, 32 1 1/4 1 5/8-12 1 5/8-12 51 27 40 52 36 41 572 20 V6X-S 20 V6X-SS 250 210 35, 38 1 1/2 1 7/8-12 1 7/8-12 57 33 45 58 39 48 715 24 V6X-S 24 V6X-SS 170 140 2 2 1/2-12 2 1/2-12 72 45 56 70 50 66 960 32 V6X-S 32 V6X-SS 110 110Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.PN (bar)= PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.V6MX 45° Swivel nut elbowTriple-Lok ® 37° Flare end / Triple-Lok ® 37° Flare female swivel endSAE 070321 MS51522Tube Thread Thread Weight PN (bar)O.D. UN/UNF-2A UN/UNF-2B C3 D M M5 M10 Y (steel) Triple-Lok ® Triple-Lok ®mm in. T T6 mm mm mm mm mm mm g/1 piece Steel Stainless Steel S SS 6 1/47/16-20 7/16-20 16 4 23 25 17 11 44 4 S6X-S 4 S6X-SS 500 350 8 5/161/2-20 1/2-20 17 6 24 27 17 13 58 5S6MXS 5 S6X-SS 420 350 10 3/89/16-18 9/16-18 19 8 27 32 22 14 71 6S6MXS 6 S6X-SS 350 350 12 1/23/4-16 3/4-16 22 10 32 35 24 19 133 8S6MXS 8 S6X-SS 350 350 14, 15,16 5/87/8-14 7/8-14 27 12 37 41 28 22 203 10S6MXS 10 S6X-SS 350 350 18, 20 3/41 1/16-12 1 1/16-12 32 16 42 44 30 27 328 12S6MXS 12 S6X-SS 350 350 25 11 5/16-12 1 5/16-12 38 22 46 51 36 33 483 16S6MXS 16 S6X-SS 250 250 28, 30, 32 1 1/41 5/8-12 1 5/8-12 50 28 52 59 43 41 708 20 S6X-S 20 S6X-SS 250 210 35, 38 1 1/2 1 7/8-12 1 7/8-12 57 33 59 68 49 48 1100 24 S6X-S 24 S6X-SS 170 170Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.PN (bar) = PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.S6MX Swivel nut branch teeTriple-Lok ® 37° Flare ends / Triple-Lok ® 37° Flare female swivel endSAE 070433 MS51524KTube Thread Thread Weight PN (bar) O.D. UN/UNF-2A UN/UNF-2B C3 D M M5 M10 Y (steel) Triple-Lok ® Triple-Lok ®mm in. T T6 mm mm mm mm mm mm g/1 piece Steel Stainless Steel S SS 6 1/4 7/16-20 7/16-20 16 4 23 25 17 11 44 4 R6X-S 4 R6X-SS 500 350 8 5/16 1/2-20 1/2-20 17 6 24 27 17 13 56 5R6MXS 5 R6X-SS 420 350 10 3/8 9/16-18 9/16-18 19 8 27 32 22 14 69 6R6MXS 6 R6X-SS 350 350 12 1/2 3/4-16 3/4-16 22 10 32 35 24 19 136 8R6MXS 8 R6X-SS 350 350 14, 15,16 5/8 7/8-14 7/8-14 27 12 37 41 28 22 207 10R6MXS 10 R6X-SS 350 350 18, 20 3/4 1 1/16-12 1 1/16-12 32 16 42 44 30 27 319 12R6MXS 12 R6X-SS 350 350 22 7/8 1 3/16-12 1 3/16-12 35 18 46 45 34 33 622 14 R6X-S 14 R6X-SS 250 250 25 1 1 5/16-12 1 5/16-12 38 22 46 51 36 33 489 16R6MXS 16 R6X-SS 250 250 28, 30, 32 1 1/4 1 5/8-12 1 5/8-12 50 28 52 59 43 41 712 20R6MXS 20 R6X-SS 250 210 35, 38 1 1/2 1 7/8-12 1 7/8-12 57 33 59 66 47 48 1100 24 R6X-S 24 R6X-SS 170 170Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.PN (bar)= PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.R6MX Swivel nut run teeTriple-Lok ® 37° Flare ends / Triple-Lok ® 37° Flare female swivel endSAE 070432KKTubeThread Thread Weight PN (bar) O.D.Metric UN/UNF-2A L D C U (steel) Triple-Lok ® Triple-Lok ® mm in. T87 T mm mm mm mm g/1 piece Steel Stainless Steel S SS 6 1/4 M10 × 1.0 7/16-20 30 14 14 9 25 4M10F87OMXS 4M10F87OMXSS 500 350 8 5/16 M10 × 1.0 1/2-20 30 14 14 9 30 5M10F87OMXS 5M10F87OMXSS 420 350 8 5/16 M12 × 1.5 1/2-20 33 14 19 11 37 5M12F87OMXS 5M12F87OMXSS 420 350 8 5/16 M14 × 1.5 1/2-20 34 14 19 11 40 5M14F87OMXS 5M14F87OMXSS 420 350 10 3/8 M14 × 1.5 9/16-18 34 14 19 11 44 6M14F87OMXS 6M14F87OMXSS 420 350 10 3/8 M16 × 1.5 9/16-18 36 14 22 12 53 6M16F87OMXS 6M16F87OMXSS 420 350 10 3/8 M18 × 1.5 9/16-18 37 14 24 13 60 6M18F87OMXS 6M18F87OMXSS 350 350 12 1/2 M14 × 1.5 3/4-16 36 17 19 11 41 8M14F87OMXS 8M14F87OMXSS 420 350 12 1/2 M16 × 1.5 3/4-16 38 17 22 12 57 8M16F87OMXS 8M16F87OMXSS 420 350 12 1/2 M18 × 1.5 3/4-16 39 17 24 13 71 8M18F87OMXS 8M18F87OMXSS 350 350 14, 15,16 5/8 M14 × 1.5 7/8-14 41 19 24 11 73 10M14F87OMXS 10M14F87OMXSS 350 350 14, 15,16 5/8 M18 × 1.5 7/8-14 43 19 24 13 75 10M18F87OMXS 10M18F87OMXSS 350 350 14, 15,16 5/8 M22 × 1.5 7/8-14 44 19 27 13 98 10M22F87OMXS 10M22F87OMXSS 350 350 14, 15,16 5/8 M27 × 2.0 7/8-14 46 19 32 16 75 10M27F87OMXS 10M27F87OMXSS 350 350 18, 20 3/4 M22 × 1.5 1 1/16-12 48 22 27 13 104 12M22F87OMXS 12M22F87OMXSS 350 350 18, 20 3/4 M27 × 2.0 1 1/16-12 51 22 32 16 158 12M27F87OMXS 12M27F87OMXSS 350 350 25 1 M27 × 2.0 1 5/16-12 51 23 36 16 206 16M27F87OMXS 16M27F87OMXSS 280 280 25 1 M33 × 2.0 1 5/16-12 53 23 41 16 273 16M33F87OMXS 16M33F87OMXSS 280 280 28, 30, 32 1 1/4 M42 × 2.0 1 5/8-12 55 24 50 16 431 20M42F87OMXS 20M42F87OMXSS 280 210 35, 38 1 1/2 M48 × 2.0 1 7/8-12 59 28 55 18 564 24M48F87OMXS 24M48F87OMXSS 210 140Steel, stainless steel and brass Triple-Lok ® parts are delivered with NBR elastomeric seals as standard. For more details on other seal materials see page K93.Order codes shown are part of our current manufacturing programme.Imperial and metric parts may vary in hexagon dimensions.PN (bar) = PN (MPa)10Pressure ratings – PN shown, apply to Steel and Stainless Steel versions of the product.F87OMX Male stud connectorTriple-Lok ® 37° Flare end / Male metric thread – O-ring (ISO 6149)KTube Thread Thread Weight PN (bar) O.D. UN/UNF-2A UN/UNF-2A C4 D D2 L5 LL (steel) Triple-Lok ® Triple-Lok ®mm in. T5 T mm mm mm mm mm g/1 piece Steel Stainless Steel S SS 1/8 5/16-24 5/16-24 11 2 2 27 19 8 2 F5OX-S 500 — 3/16 3/8-24 3/8-24 13 3 3 28 20 10 3 F5OX-S 500 — 3/16 5/16-24 3/8-24 13 3 2 28 20 9 3-2 F5OX-S 500 — 6 1/4 7/16-20 7/16-20 14 4 4 31 22 15 4F5OMXS 4F5OMXSS 500 350 6 1/4 3/8-24 7/16-20 14 5 3 30 23 12 4-3 F5OX-S 4-3F5OMXSS 500 350 6 1/4 1/2-20 7/16-20 16 4 6 31 22 25 4-5 F5OX-S 4-5F5OMXSS 420 350 6 1/4 9/16-18 7/16-20 17 4 4 33 23 27 4-6F5OMXS 4-6F5OMXSS 420 350 6 1/4 3/4-16 7/16-20 22 4 10 35 24 35 4-8 F5OX-S 4-8F5OMXSS 420 350 6 1/4 7/8-14 7/16-20 25 5 5 38 25 60 4-10 F5OX-S 4-10F5OMXSS 350 350 8 5/16 1/2-20 1/2-20 16 6 6 31 22 18 5F5OMXS 5F5OMXSS 420 350 8 5/16 7/16-20 1/2-20 14 6 5 31 22 18 5-4 F5OX-S 5-4F5OMXSS 420 350 8 5/16 9/16-18 1/2-20 17 6 6 33 23 25 5-6 F5OX-S 5-6F5OMXSS 420 350 8 5/16 3/4-16 1/2-20 22 6 6 35 24 40 5-8 F5OX-S 5-8F5OMXSS 420 350 10 3/8 9/16-18 9/16-18 17 8 8 33 23 25 6F5OMXS 6F5OMXSS 420 350 10 3/8 7/16-20 9/16-18 16 8 4 32 23 40 6-4 F5OX-S 6-4F5OMXSS 420 350 10 3/8 1/2-20 9/16-18 16 8 6 32 23 56 6-5 F5OX-S 6-5F5OMXSS 420 350 10 3/8 3/4-16 9/16-18 22 8 8 35 24 44 6-8F5OMXS 6-8F5OMXSS 420 350 10 3/8 7/8-14 9/16-18 25 8 12 38 25 85 6-10 F5OX-S 6-10F5OMXSS 350 350 10 3/8 1 1/16-12 9/16-18 32 8 16 42 27 100 6-12 F5OX-S 6-12F5OMXSS 350 350 12 1/2 3/4-16 3/4-16 22 10 10 38 27 58 8F5OMXS 8F5OMXSS 420 350 12 1/2 7/16-20 3/4-16 21 10 5 38 29 40 8-4 F5OX-S 8-4F5OMXSS 420 350 12 1/2 9/16-18 3/4-16 19 10 10 37 27 44 8-6F5OMXS 8-6F5OMXSS 420 350 12 1/2 7/8-14 3/4-16 27 10 10 41 28 73 8-10F5OMXS 8-10F5OMXSS 350 350 12 1/2 1 1/16-12 3/4-16 32 10 10 45 30 126 8-12F5OMXS 8-12F5OMXSS 350 350 12 1/2 1 5/16-12 3/4-16 41 10 10 45 30 160 8-16 F5OX-S 8-16F5OMXSS 310 310 14, 15,16 5/8 7/8-14 7/8-14 27 12 12 43 31 75 10F5OMXS 10F5OMXSS 350 350 14, 15,16 5/8 9/16-18 7/8-14 18 13 8 43 34 60 10-6 F5OX-S 10-6F5OMXSS 350 350 14, 15,16 5/8 3/4-16 7/8-14 24 12 10 42 31 65 10-8F5OMXS 10-8F5OMXSS 350 350 14, 15,16 5/8 1 1/16-12 7/8-14 32 12 12 47 32 132 10-12F5OMXS 10-12F5OMXSS 350 350 14, 15,16 5/8 1 5/16-12 7/8-14 41 13 13 48 33 170 10-16 F5OX-S 10-16F5OMXSS 310 310 18, 20 3/4 1 1/16-12 1 1/16-12 32 16 16 50 35 134 12F5OMXS 12F5OMXSS 350 350 18, 20 3/4 3/4-16 1 1/16-12 29 16 10 49 38 104 12-8 F5OX-S 12-8F5OMXSS 350 350 18, 20 3/4 7/8-14 1 1/16-12 27 16 12 48 35 108 12-10F5OMXS 12-10F5OMXSS 350 350 18, 20 3/4 1 3/16-12 1 1/16-12 35 16 16 50 35 170 12-14 F5OX-S 12-14F5OMXSS 310 310 18, 20 3/4 1 5/16-12 1 1/16-12 38 16 16 51 35 197 12-16F5OMXS 12-16F5OMXSS 310 310 18, 20 3/4 1 5/8-12 1 1/16-12 48 16 16 53 38 230 12-20 F5OX-S 12-20F5OMXSS 280 280 22 7/8 1 3/16-12 1 3/16-12 35 18 18 51 36 174 14 F5OX-S 14F5OMXSS 280 280 22 7/8 1 5/16-12 1 3/16-12 38 18 22 51 36 223 14-16 F5OX-S 14-16F5OMXSS 280 280 25 1 1 5/16-12 1 5/16-12 38 22 22 52 37 203 16F5OMXS 16F5OMXSS 280 280 25 1 3/4-16 1 5/16-12 35 22 10 45 34 160 16-8 F5OX-S 16-8F5OMXSS 280 280Continued on page K30F5OMX Male stud connectorTriple-Lok ® 37° Flare end / Male UN/UNF thread – O-ring (ISO 11926)SAE 070120 MS51525。

parker eo2卡套式管接头的装配

密封圈。
检查卡套是否有任何缺陷或损坏，如裂纹、变形等，确保其完好无损。
涂抹润滑剂
在卡套和密封圈上涂抹适量的润滑剂，以减少摩擦并提高装配的顺畅
性。
安装卡套
将卡套轻轻地推入管接头的内孔，确保卡套完全进入，没有扭曲或倾
斜。
插入管子
01
选择合适的管子
根据需要连接的管道尺寸，选择合适的管子，并确保其清洁无杂物。
如需调整管子的角度，应先松开管子的固定螺丝，调整后再重新固定。
04 装配后的检查与测试
检查密封性
总结词
密封性是确保管接头正常工作的关键因素，必须进行严格检查。
详细描述
在装配完成后，应立即对eo2卡套式管接头的密封性进行检查。这包括检查卡套是否紧固，无泄漏现象，以及管接头的各个部分是否紧密贴合。任何泄漏都可能导致流体外泄，影响设备的正常运行。
适应性强
parker eo2卡套式管接头适用于各种材质和规格的管道连接，具有较强的适应性。
02 装配前的准备
检查工具与材料
工具
确保您拥有适合的装配工具，如扳手、螺丝刀和管钳等。
材料
检查是否备齐了所需的管接头、密封圈、螺母和螺栓等材料。
检查接头与管道
接头
检查接头是否完好无损，没有裂纹或损伤，以确保其密封性能。
02
03
涂抹润滑剂
插入管子
在管子的插入端涂抹适量的润滑剂，以减少摩擦并提高装配的顺畅性。
将管子插入已安装卡套的管接头中，确保管子插入到位，没有松动或漏缝。
调整与固定
检查密封性
检查管接头是否密封良好，如有问题应及时处理。
固定管子
使用适当的工具将管子固定在管接头上，确保其牢固不松动。

parker-legris气管

mm
mm
工作压力
20℃
PU螺旋管，4米(m) 接头斜螺纹
螺旋管部分长度
较长端直线部分长度
较短端直线部分长度

螺旋管外径
(bar)
mm
mm
mm
mm
4 6 8 12
2.5 4 5 8
10 9 8 9
R1/8 R1/4 R1/4 R3/8
1471U04 03 10 1471U06 03 13 1471U08 03 13 1471U12 03 17
1025U06R08 1025U08R08 1025U10R08 1025U12R08 1025U14R08 95
1100U06R01 1100U08R01
1100U06R04 1100U08R04
1100U06R08 1100U08R08 1100U10R08 1100U12R08 1100U14R08 95
1470U04 05 10 1470U06 05 13 1470U08 05 13 1470U12 05 17
595 630 780 780
300 300 500 500
100 100 100 100
24 32 42 65
1471U PU螺旋管，4米(m)长，附带BSPT斜螺纹(即PT斜螺纹)接头
管外径管内径
1025P10 05
1025P10 06
1100P 精密尼龙管，每卷100米(m)
管外径 mm
4 4 5 6 8 10 10 12 12 14 14 16
管内径 mm
2 2.7 3.3 4 6 7.5 8 9 10 11 12 13
常温下弯曲半径 mm
25 30 25 35 55 75 90 75 90 120 100 120 1100P04 00 1100P04 00 27 1100P05 00 33 1100P06 00 1100P08 00 1100P10 00 75 1100P10 00 1100P12 00 09 1100P12 00 1100P14 00 11 1100P14 00 1100P16 00 1100P04 01 1100P04 01 27 1100P05 01 33 1100P06 01 1100P08 01 1100P10 01 75 1100P10 01 1100P12 01 09 1100P12 01 1100P14 01 11 1100P14 01

帕克硬管接头说明书

派克硬管接头已经获得世界上各种不同机构的认证，如：德国劳氏（GL）英国劳氏（LR）挪威船级社（DNV）美国船级社（ABS）认证通常针对特定的产品、应用领域、工况条件、有效期或其他限制条件。

我们可为不同应用情况提供相应的资料文件。

派克的硬管接头同时也被世界上许多主机设备生产商或最终用户认可。

目录技术信息认证证书 .................................................................................................................................... B -2简介 ........................................................................................................................................... B -5硬管接头产品及应用概览 ........................................................................................................... B -6PSR 卡套及特点 .........................................................................................................................B-8DPR 不锈钢卡套及特点 ...........................................................................................................B-10EO-2 型接头及特点..................................................................................................................B-11EO2-FORM 型接头及特点 .......................................................................................................B-13O-Lok ® 型接头及特点 ..............................................................................................................B-15如何选择合适的硬管接头产品..................................................................................................B-17硬管接头产品的国际标准 .........................................................................................................B-25推荐使用的钢管 .......................................................................................................................B-26温度的压降影响 .......................................................................................................................B-28表面处理 ..................................................................................................................................B-29介质兼容性表 ...........................................................................................................................B-30安全指南 ..................................................................................................................................B-32装配指南装配流程简介 ...........................................................................................................................B-33EO 卡套接头装配指南 .............................................................................................................B-34EO-2 卡套接头装配指南 ..........................................................................................................B-38EO 安装工具检查.....................................................................................................................B-42EO2-FORM 装配指南 ..............................................................................................................B-43EO2-FROM 安装工具检查 .......................................................................................................B-48O-Lok ® 装配指南 .....................................................................................................................B-49Parﬂange ® 工具检查及夹具调整..............................................................................................B-52油口端安装指导 .......................................................................................................................B-53目录可调向接头及旋转螺母安装指导 ..............................................................................................B-57法兰连接安装指导....................................................................................................................B-59硬管布管指导 ..........................................................................................................................B-60安装设备KONU 锥面规 ..........................................................................................................................B-62AKL 测距仪 .............................................................................................................................B-63EO-KARRYMAT.......................................................................................................................B-64EOMAT UNI ............................................................................................................................B-65EO2-FORM F3 ........................................................................................................................B-69KARRYFLARE .........................................................................................................................B-72Parﬂange ® 1025 ......................................................................................................................B-75Parﬂange ® 50 .........................................................................................................................B-76EO-NIROMINT ........................................................................................................................B-81手动去毛刺工具 .......................................................................................................................B-82电动去毛刺工具 .......................................................................................................................B-82螺纹识别包 ..............................................................................................................................B-82接头产品EO 接头产品目录.....................................................................................................................B-83如何订购EO 接头......................................................................................................................B-87阀产品目录..............................................................................................................................B-163阀技术信息 .............................................................................................................................B-165EO 旋转接头 ............................................................................................................................B-187旋转接头技术信息....................................................................................................................B-188O-Lok ® 产品目录 ...................................................................................................................B-200如何订购O-Lok ® 接头 ..............................................................................................................B-203公制钢管信息及订货 ..............................................................................................................B-236钢管管夹概览 ...........................................................................................................................B-240目录作为管路元件供应商，派克一直致力于为您提供一个更高压力，更易安装，无需维护的无泄漏液压系统。

Parker的接头和管件的选型手册

Applications requiring the ParLock system
• Hydrostatic transmissions (combine harvesters, large tractors, excavators, etc.)
• Vibratory hammers
• Large injection moulding machines
Parker’s colour-coded die sets No loose parts to mismatch or misplace – die set segments linked together. Die sets provide 360° evenly applied crimping forces for an ideal crimp result.
Technical Handbook
Parkrimp No-Skive and ParLock System
Along with the ever-growing power and efﬁciency of construction, agriculture and other machinery and increasing working pressures and ﬂow
The perfect match The complete system from one source. No-Skive hose, No-Skive ﬁtting and crimping machine with world-wide guarantee and availability.
Parkalign® Parker’s exclusive Parkalign® positions the ﬁtting in the dies perfectly every time.

帕克尔公司氧气准备系统半精度过滤器压力调节器系列P32说明书

Global Air Preparation SystemCompact Semi-Precision Filter / Regulator - P32SymbolsFlow ‡3Max.Height Width Depth†• Integral 1/4", 3/8" or 1/2" ports (NPT, BSPP & BSPT)• High efficiency 5 micron element as standard • Excellent water removal efficiency• Robust but lightweight aluminum construction • Positive bayonet latch to ensure correct & safe fitting • Secondary pressure ranges 0-2 bar (0-30 psig), 0-4 bar, (0-60 psig), 0-8 bar (0-125 psig), 0-17 bar (0-250 psig)• Secondary aspiration plus balanced poppet provides quick response and accurate pressure regulation‡ Flow with 10 bar (145 psig) inlet pressure, 6.3 bar (91.3) psig) set pressure and 1 bar (14.5 psig) pressure drop.1Options:Global Air Preparation SystemFor best performance, regulated pressure should always be set by increasing the pressure up to the desired setting.Flow ChartsSpecificationsFlow capacity* 1/4 35 dm 3/s (75 scfm) 3/8 35 dm 3/s (75 scfm) 1/2 35 dm 3/s (75 scfm)Effect of supply pressure variation 0.04 bar (0.6 PSIG) for 1.7 bar (25 PSIG) change in P1Operating Plastic bowl -25°C to 52°C (-13°F to 125°F) temperature Metal bowl -25°C to 65.5°C (-13°F to 150°F)Max. supply Plastic bowl 10 bar (150 psig)pressure Metal bowl 17 bar (250 psig)Standard filtration 5 micronUseful retention † 51 cm 3(1.7 US oz.)Adjusting range pressure 0-2 bar (30 psig) 0-4 bar (60 psig) 0-8 bar (125 psig) 0-17 bar (250 psig)Port size BSPP / BSPT / NPT 1/4, 3/8, 1/2Gauge port (2 ea.) BSPP / BSPT / NPT 1/4Weight 0.53 kg (1.17 lbs)* Inlet pressure 10 bar (145 psig). Secondary pressure 6.3 bar (91.3 psig).†Useful retention refers to volume below the quiet zone baffle.Air quality :Within ISO 8573-1: 1991 Class 3 (Particulates); 2001 Class 6 (Particulates)Material SpecificationsBody Aluminum Adjustment knob Acetal Element retainer / Baffle Acetal Bowl Plastic bowl Polycarbonate Metal bowl Zinc Bowl guard Nylon Filter element Sintered polyethyleneSealsNitrile Springs Main regulating / valve Steel / S.S.Valve assemblyBrass / Nitrile Diaphragm assembly Nitrile / ZincPanel nutAcetal Sight gauge Metal bowl PolycarbonateRepair and Service KitsPlastic bowl / Bowl guard manual drain P32KB00BGM Metal bowl / Sight gauge manual drain P32KB00BSM Auto drainP32KA00DA 5µ particle filter elementP32KA00ESE Regulator repair kit - relieving P32KB00RB Regulator repair kit - non-relieving P32KB00RC Panel mount nut - aluminum P32KA00MM Panel mount nut - plasticP32KA00MP Angle bracket (fits to panel mount threads) P32KB00MR T -bracket (fits to body connector) P32KA00MB T -bracket with body connector P32KA00MT Body connectorP32KA00CB1/4 Filter / Regulator3/8 Filter/Regulator1/2 Filter/RegulatorWARNINGProduct rupture can cause serious injury.Do not connect regulator to bottled gas.Do not exceed Maximum primary pressure rating.!Manual DrainDimensions mm (inches)Gauges50mm (2") Round 1/4" center back mount0-30 psig / 0-2 barK4520N140300-60 psig / 0-4 bar K4520N140600-160 psig / 0-11 bar K4520N141600-300 psig / 0-20 barK4520N14300S e c o n d a r y P r e s s u r e - b a r S e c o n d a r y P r e s s u r e - (p s i g )0204060801001201400Flow - dm 3/s Flow - (scfm)2040103060805070S e c o n d a r y P r e s s u r e - b a r S e c o n d a r y P r e s s u r e - (p s i g )0204060801001201400Flow - dm 3/s Flow - (scfm)2040103060805070S e c o n d a r y P r e s s u r e - b a r S e c o n d a r y P r e s s u r e - (p s i g )0204060801001201400Flow - dm 3/s Flow - (scfm)2040103060805070。

Parker Hannifin 水管产品分公司产品说明书

A s s e m b l y E q u i p m e n tDAH o s eBCEFGF i t t i n g sP a r k r i m p C r i m p i n g E q u i p m e n tA d a p t e r sA c c e s s o r i e sA p p e n d i c e sHose Assembly EquipmentCatalog 4400 US Hose Assembly EquipmentVisual IndexHose Assembly EquipmentCatalog 4400 US Model No. 2726 - Mandrel Tool Kit - 23 Series (SAE45°&PTT30°)Visual IndexTH8-400 - Production CrimperModel No. 339 & 239 - Hose Cut-Off MachineModel No. 332T-115V - Hose Cut-Off Machine Model No. 631075 - Karrykut -Hose Cut-Off MachineModel No. 871522 -Handycut -Hose Cut-Off MachineModel No. 881540 -Push-Lok Cut-Off & Assembly ToolModel No. 316 - Hose Cut-Off ToolModel No. TH11-1 - Hose Cut-Off ToolModel No. TH9-1 - HoseInsertion Depth Blocks (Gauges)Model No. TH2-7 - Fittings Push-On Stand Model No. 432-115V -Hozembler & StandModel No. 80C-SDR - Swivel Die RackModel No. 80C-0DR - Die Storage RackHoze-OilAccrolube - High Efficiency Lubricant601069- Hose PerforatorModel No. 652200 - Mandrel Tool Kit - 22 SeriesModel No. 2727 - Mandrel Tool Kit - 23 Series (JIC 37° Flared)Model No. 652201 - Assembly Tools - 22 SeriesHydraulic Hose and Flow Capacity GuideD-3D-9D-4D-4D-5D-5D-5D-5D-6D-6D-6D-7D-7D-7D-8D-8D-8D-8D-9D-9Hose Assembly Equipment Catalog 4400 USProduction CrimperTH8-400♦Specifications· Power:230 Volts 3 Phase 60 Hz· Weight:1000 lbs· Width:27 inches· Depth:44 inches· Height:58 inches· Height to center of dies:48·1/2 inches· Capacity:1-1/4" SAE 100R1AT Max.1" DIN 20 022-1SN Max.1-1/4" SAE 100R2AT Max.1-1/4" DIN 20 022-2SN Max.1" SAE 100R3 Max.1-1/4" SAE 100R4 Max.7/8" SAE 100R5 Max.7/8" SAE J1402 AI Max.7/8" SAE J1402 AII Max.1-1/4" SAE 100R9 Max.1-1/4" SAE 100R12 Max.1" SAE 100R16 Max.1-1/4" SAE 100R17 Max.· Cycle Time: 301-8 (1/2" SAE 100R2A T) — 4 seconds perstraight end fitting· Die Changeover Time: One piece cartridge — less than 60seconds♦Features· Enclosed power unit.· One piece quick set-up cartridge die.· Foot pedal operated.· Ten sets of dies will cover the entire range of hoseand fittings through 1¼” (-20) SAE100R12, requiring 43and 71 Series coupling through -20 size.· Die storage area within cabinet.· Horizontal feed to improve cycle time.· Some die sets will handle more than one type andsize: e.g., one set will handle 43 Series (-8) and 71Series (-6), while another will handle 43 Series (-10)and 71 Series (-8).Standard die sets available are:Fitting Series Size26 Series-4 through -2043 Series-4 through -2071 Series-6 through -20Other dies sets are available upon request.♦Optional ToolingDie Set43 Series71 SeriesPart Number Size SizeTH8-400DC16-4TH8-400DC18-5TH8-400DC21-6TH8-400DC24-8-6TH8-400DC27-10-8TH8-400DC31-12-10TH8-400DC34-12TH8-400DC40-16TH8-400DC43-16TH8-400DC50-20-20Die Set26 SeriesPart Number SizeTH8-400DC26-4-4TH8-400DC26-5-5TH8-400DC26-6-6TH8-400DC26-8-8TH8-400DC26-10-10TH8-400DC26-12-12TH8-400DC26-16-16TH8-400DC26-20-20Production CrimperHose Cut-Off MachineModel No. 339 and 239Model 339Designed for heavy duty use. Will cut multi-braided wire reinforced hoses including 6 heavy spiral constructions up to 2" inside diameters. Model 339 comes equipped with 2 cut-off blades of a special scalloped construction. Equipped with 3 HP motor 230V, 3 phase, 60 cycle.Dimensions:22" wide x 42" long x 24" high Shipping Weight:115 lbs. Replacement Scallop Cutting Blade (10" with 3/4" arbor size) Part No. 24248 Replacement Smooth Cutting Blade Part No. 15960 Model 239This is Model 339 with 230V single-phase motor Part No. 239 For additional information see Bulletin #4497-B11.Hose Cut-Off MachineModel No. 332T-115VPower unit for quick, easy cutting of cotton or rubber covered fabric braid or wire reinforced hose. Equipped with 1-1/2 HP, 3450 RPM, 115/230V single phase electric motor wired for 115V. Belt driven cutting wheel of high speed steel, hardened and ground for smooth, dust-free, long-lasting service. Moving parts shielded by guards. Includes a Smooth Cutting Blade (8" with 5/8" arbor size)Model 332T-115V will cut:two wire braid, 1-1/4" maximumone wire braid, 2" maximumfour spiral, 1-1/4" maximumReplacement Smooth Cutting Blade (8" with 5/8" arbor size)Part No. 580661 Replacement Scallop Cutting Blade Part No. 24398Hose Cut-Off Machine - Karrykut Model No. 631075A portable power saw for cutting on the job. Hardened steel blade powered by 115V (13 amp) universal AC motor. Hand grip, trigger control. Unique clamp spreads hose as it is cut to prevent binding of blade.Cuts rubber and cotton covered, wire or fabric reinforced hose from: 1/4" through 2" inside diameter.Cuts 4 spiral light wire hose: 1-1/4" maximumUniversal Clamp Attachment:Part No. 631076 Universal clamp attachment may be used with any portable power saw unit having a 5/8" arbor, 8" blade capacity.Replacement Cutting Blade (8" with 5/8" arbor size):Part No. 580661 Replacement Power Saw (less clamp and blade):Part No. 631140 Hose Cut-Off Tool - HandykutModel No. 871522Handykut is a portable tool designed for efficient cutting of hose. Once Handykut is positioned onto a flat surface by clamps or by locking it in a vise, properly align the hose in a radius and cut it with a hacksaw.Push-Lok Cut-Off & Assembly Tool Model No. 881540This unique tool combines a hose cutter with a toggle-action that presses the fitting into the hose.Designed to handlePush-Lok hose from 1/4" through 3/4", this tool makes the job easier whether you are making one assembly or a hundred. Overall length:16" Weight:Approximately 4 pounds Hose Cut-Off ToolModel No. 316Model 316 hose cut-off tool is a small size, easy to use, manually operated unit for quick cutting of Parker 235, 293, 601, and 604 hoses. It can also be used for Push-Lok hose 801, 804, 821, 821FR, 831 and 836. Ruggedly built for yearsof trouble-free service.Hose Cut-Off ToolModel No. TH11-1Parker Push-Lok cutters are designed for quick, easy cutting of Push-Lok hose in all sizes and non-wire reinforced hose. TH11-1squarely cuts Push-Lok hose 1/4" I.D. through3/4" I.D.Hose Insertion Depth BlocksFor quick and easy marking of hose insertion depth. A faster way to leak-free assemblies.Ensures accuracy. Increase productivity.The first step toward a leak-free hose assembly is accuratelymarking the proper hose insertion depth. This is a fail-safe way to quickly and easily mark proper insertion depth, each and every time. With aluminum blocks and steel mandrels, Hose Insertion Depth Blocks feature a range of sizes clearly designated for a specific fitting series.Note: For additional information, please see Bulletin #4480-B53-USA.Hose Cut-Off Tool, Hose Insertion Gauges,and Fitting Push-On StandFitting Push-On Stand Part No. TH2-7Fitting Push-On Stand is the fastest way to make Parker hose assemblies in production volumes.Quickly and easily pushes fittings onto hose.Boosts productivity and quality. Reduces worker fatigue. The Push-On Stand eliminates the need of rubber mallets, oils and a lot of elbow grease to get fittings all the way onto the end of hose for crimping. Comes complete with straight tooling required for sizes -4 to -32, all permanent series, 82 Push-Lok, and 88 series field attachable fittings. Elbow Pusher Set (TH2-7-ELS) available.Note: For additional information, please see Bulletin #4480-B36-USA.Die Racks and HozemblerHozemblerModel 432-115VThe 432 Hozembler is a power machine to facilitate the attachment of reusable hose fittings. It readily handles all types of hose and fittings in sizes -3 through -32 I.D., including standard bent tube elbow. The 432 will also handle assembly of 4 heavy wire spiralthrough -24, I.D.115V, 30 amp, universal AC motor. Model 432 is supplied complete with foot switch and safety guard.Model 432 Hozembler (complete with vise and all adapters)Part No. 432-115VMounting stand:Part No. 662451Replacement PartsHose vise (complete with 662453 and 662454)Part No. 662452Hose vise jaw plate Part No. 662453Hose vise jaw adapter Part No. 662454Chuck jaws Part No. 662455Chuck jaws adapter set for use with most bent tube ends and hose fitting hex sizes up to 1/2".Part No. 662456Request Bulletin # 4497-B2 for operating instructions.Swivel Die Rack Part No. 80C-SDRHolds up to 30 dies. Accommodates any size Parkrimp die. Powder-coated, heavy-duty steel construction.The convenient new Swivel Die Rack, organizes and stores your collection of dies so they're always ready to work when you are. The Swivel Die Rack consists of a base unit and up to five circularholders, each with the capacity to hold five or six dies. It is floor or bench mountable.Note:For additional information, please see Bulletin #4480-B54-USA.Die Storage Racks 80C-0DR and 83C-0DRThe 80C-0DR and 83C-0DR Die Storage Racks are modular die rack designed to hold small and large Parkrimp dies.The 80C-0DR will store three sets of small dies while the 83C-0DR is capable of storing two sets of large dies. The modules can be bolted together horizontally or vertically. They can also be bolted to the work bench. Clips are provided to bolt the modules to a wall or the side panel of a truck for additional stability.Request Bulletin #4480-B26 for additional information.Hose Assembly EquipmentCatalog 4400 USHoze-OilParker’s improved hose assembly lubricant reduces hose assembly make-up time.Hoze-Oil reduces torque and eliminates waste lubrication. It’s cleaner, too! Simply dip the cut hose ends into Parker Hoze-Oil and proceed with the Parkrimp or Reusable fitting hose assembly make-up.Hoze-OilPart No. Hoze OilHose PerforatorSmall hand tool to prick minute holes in the rubber cover of hose to be used in gaseous service where the pressure exceeds 250 psi.The Hose Perforator is intended to be held in the hand and driven into the cover every few inches of length either striking the hose or by a rolling action over the hose cover. It is not generally necessary to perforate the hose on all sides.Hose PerforatorPart No. 601069Mandrel Tool Kit - 22 Series Model No. 652200The Mandrel Tool Kit is for assembling Parker 22 Series hosefittings. One of each of the parts listed below are included in the kit.Hose and Fitting Lubricants, Hose Perforator,and Mandrel KitsAccrolubeAccrolube is a high efficiency lubricant that will make the assembly of stainless steel field attachable fittings easier. Accrolube contains Teflon which creates a boundary lubrication film that reduces wear between metal surfaces, protects against corrosion, and ulitmately eliminates galling.AccrolubePart No. AccrolubeHose Assembly Equipment Catalog 4400 USMandrel Tool Kit - 23 SeriesModel No. 2727(for JIC 37° flared fittings)Model No. 2726(for SAE 45° and PTT 30°flared fittings)The Mandrel Tool Kit is for assembling 23 Series hose fittings.One of each of the parts listed below are included in the kit.Mandrel KitsAssembly Tools - 22 SeriesModel No. 652201The Model No. 652201 tool kit is for assembling 22 Series hosefittings. One of each of the parts listed below are included in the kit.Hydraulic Hose and Flow Capacity GuideProductivity tool that is pocket sized, quick and easy to referenceand offers correct specifications the first time. The hydraulic hosechart provides working pressure and burst pressure levels forvarious Parker hose sizes in both metric and U.S. units. The flowcapacity chart is a quick reference for flow capacities at recom-mended flow velocities for pressure, return and suction lines.Hydraulic Hose and Flow Capacity Guide Part #: Bul. 4480-T14-USAHose Assembly Equipment Catalog 4400 USNotes。

Parker软管培训资料-派克液压胶管培训资料-技术培训资料

工作压力应保持在额定范围内，不得超压使用。
02
液压胶管连接
应正确连接接头，避免渗漏或空气进入液压系统。
03
液压胶管清洁
保持管道清洁，防止灰尘和杂质进入液压系统。
液压胶管故障排除与预防
液压胶管漏油
如出现漏油，应检查管道和接头是否受损，如有问题及时更换。
液压胶管噪音
如出现噪音，应检查液压胶管是否太紧或老化，如有问题及时更换。
2023
《parker软管培训资料-派克液压胶管培训资料-技术
培训资料》
目录
• Parker软管介绍 • Parker液压胶管介绍 • Parker液压胶管技术培训 • Parker液压胶管应用案例 • Parker液压胶管与其他产品的比较 • Parker液压胶管市场前景与展望
01
Parker软管介绍
环保与节能趋势
在环保和节能方面，液压胶管也面临着新的挑战和机遇，如发展耐高温、耐高压、低流阻的液压胶管，减少能源消耗和降低环境污染。
Parker液压胶管在市场中的地位
市场领导者
作为液压胶管领域的知名品牌，Parker在市场中具有极高的知名度和影响力，是液压胶管市场的领导者之一。
技术创新者
Parker在液压胶管领域一直致力于技术创新和产品升级，推出了一系列高品质的液压胶管产品，引领行业发展。
03
Parker液压胶管技术培训
液压胶管安装与维护
液压胶管储存
应储存于干燥、无尘和温度稳定的地方，避免阳光直射。
液压胶管安装
安装前应检查管道是否有损伤，安装时应使用正确的工具，避免强力扭曲或弯曲。
液压胶管维护
定期检查软管是否出现磨损、裂纹或老化，及时更换。

Parker Balston 72-007气接收器安装、操作和维护手册说明书

Parker Hannifin Corporation Industrial Gas Filtration and Generation Division Lancaster, NY • 1-716-686-64001All installation, operation, and maintenance procedures for the Parker Balston 72-007 Receiving Tank should be performed by suitable personnel using reason-able care.To mount the Parker Balston 72-007 securely on the wall, first drill two 1/4" (6 mm)diameter holes, approximately 1" (25 mm) deep, according to the mounting template (enclosed) and mounting dimensions (see Figure 2). Next, press the wall anchors into the holes until flush with the surface of the wall. Thread the 10-24 self-taping screws into the wall anchors using a Phillips screwdriver. Leave a small gap (slightly greaterFigure 1 - Overall DimensionsThese instructions must be thoroughly read and understood before installing and operating this product. If you have any questions or concerns, please call the Technical Services Department at 800-343-4048, 8AM to 5PM Eastern Time **************************************.Forotherlocations,pleasecontact your local representative.Please save product packaging for future use.The Parker Balston 72-007 Gas Receiver is a compact gas reservoir which can beeasily incorporated into any analytical laboratory. The 72-007, as a storage vessel, is ideal for smoothing pressure and concentration fluctuations from gas purification sys-tems which may impact the operation of sensitive analytical instruments. The receiver has a capacity of 3/4 gallons (0.1 SCF , 3 liters), a maximum pressure rating of 240 psig (16.5 barg), and 1/8" NPT inlet and outlet ports. At 240 psig (16.5 barg), the 72-007 will hold 1.7 SCF (50 liters) of compressed gas. The 72-007 may be mounted on a nearby wall or rest securely on a benchtop.The Parker Balston 72-007 Gas Receiver package includes: the receiver tank, receiver bracket, and all necessary mounting hardware.General Description Mounting Bulletin TI-72007JInstallationBulletin TI-72007JInstallation, Operation and Maintenance ManualTechnical Information Parker Balston ® Model 72-007 Gas Receiver Parker Hannifin Corporation Industrial Gas Filtration and Generation Division Lancaster, NY • 1-716-686-64002Piping Figure 2Mounting Dimensions Figure 3Sample InstallationNOTE: RECEIVER SHOULD BE CENTERED ONBRACKET DURING USE AND STORAGE.Principal Specifications Model Number72-007Material of Construction3003 Aluminum Max. Temperature130°F (54°C)****************************240 psig (16.5 barg) Capacity @ Atmospheric Pressure0.1 SCF (3 liters)Capacity @ 60 psig (4.1 barg)0.5 SCF (14 liters)Capacity @ 80 psig (5.5 barg)0.7 SCF (18 liters)Capacity @ 100 psig (6.9 barg)0.8 SCF (22 liters)Dimensions 5" dia. x 18" length (12 cm x 45 cm)Shipping Weight 4 lb. (2 Kg)than the thickness of the bracket) between the head of the screw and the surface of the wall. Hang the receiver bracket on the wall, lining up the keyhole slots and the installed screws. Finally, tighten the self-tapping screws until the receiver bracket is snug against the wall. Do not over-tighten. Over-tightening may strip the wall anchors.Check the epoxy bead which has been deposited at the interface of the receiver head andreceiver body to ensure proper alignment and seal integrity. (The epoxy bead was depos-ited at the factory after seal integrity was assured.) If the epoxy bead is not intact, tighten receiver head until the bead is aligned and pressure test for leaks. If unit continues to leak after tightening, consult the factory.Place the 72-007 receiver tank in the bracket, either on the wall or on the benchtop. Pipe the supply gas to the 1/8" NPT inlet port (use PTFE tape as needed), labeled “1”, on thehead of the receiver. (Note: The inlet and outlet ports are interchangeable, if needed, forease of installation). Pipe the gas from the outlet port, labeled “2”, to the instrument or analyzer (see Figure 3). Re-check the epoxy bead on the receiver.Do not rotate the receiver head relative to the body. Rotation of the receiver head may loosen the seal and cause the gas receiver to leak.Purge the receiver and downstream piping for 5 to 10 minutes prior to initial startup of analytical equipment to ensure gas purity throughout the system.Copyright© Parker Hannifin Corporation 2001, 2011 Printed in U.S.A. Bulletin TI-72007J Parker Hannifin (UK) Ltd Gas Separation & Filtration Division EMEA Dukesway, Team Valley Trading Estate Gateshead, Tyne & Wear, NE11 0PZ United Kingdom Ph: +44 (0)191 402 /gsfeParker Hannifin CorporationIndustrial Gas Filtration and Generation Division 4087 Walden Avenue Lancaster, NY 14086Tel: 716-686-6400 Fax: 。

Parker Pneumatic产品目录说明书

Catalog PDN1000-2USParker PneumaticSolenoid Operators - CNOMO MaterialsTechnical data -Solenoid operators, coil combinationsPilot ValveBody:Polyamide Armature tube:BrassPlunger & core:Corrosion resistant Cr-Ni steel Seals:Fluorocarbon Screws:Stainless steelCoilEncapsualtion material:Thermoplastic as standard Duroplast for M12 connectionTransientsInterrupting the current through the solenoid coil produces momentary voltage peaks which, under unfavourableconditions, can amount to several hundred times the rated operating voltage. Normally, these transients do not cause problems, but to achieve the Maximum life of relays in the circuit (and particularly of transistors, thyristors and integrated circuits) it is desirable to provide protection by means of voltage-dependent resistors (varistors). All connectors/cable plugs EN175301-803 with LED’s include this type of circuit protection.Solenoid Coils with M12 ConnectionSolenoid Coils with DIN A or Industrial B Connectionabove part numbers for spares. The operators are supplied with mounting screws and interface ‘O’ rings. Coils and connectors must be ordered separately.22mm x 30mm Order code 30mm x 30mm Order code Spare Base Solenoid Pilot Operator CNOMO NCAir Preparation ProductsGlobal Modular Solenoid OperatorsNC Normal Operatorwith 22 x 30 standard coilNC Normal Operator with 30 x 30 standard coil Working pressure 0 to 10 bar 0 to 10 bar Ambient temperature -10°C to 60°C *-10°C to 60°C *Power (DC) 4.8W 2.7W Power (AC)8.5VA 4.9VA Voltage tolerance +/-10%+/-10%Duty cycle 100%100%Insulation class FFElectric connection B Industrial DIN 43650A Protection IP65IP65Approval UL/CSAWorking mediaAll neutral media such as compressed air* Limited to 50°C if use with 100% duty cycle(Revised 07-15-13)Click here to view bookmarks.Catalog PDN1000-2US Parker PneumaticAir Preparation ProductsGlobal Modular Solenoid OperatorsSolenoid Connectors / Cable Plugs EN175301-803Order code 22mm Form B Order code 30mm Form A Solenoid coil dimensions mm (inches)Cable plug dimensions mm (inches)Electrical schematics22mm Form B Industrial Cable plugs 22 x 30mm30 x 30mm30mm DIN 43650ACable plugs(Revised 07-15-13)。

Parker 焊接管道产品安全指南说明书

Safety GuideWelding Hose Products Designed, Manufactured and Tested for SafetyA safe workplace begins with quality equipment – and when it comes to welding equipment, that means choosing hose products that meet or exceed industry safety standards. Parker welding hose and fitted hose assemblies meet or exceed all industry requirements as well as rigorous internal standards. Designed, manufactured and tested in America, the Parker product offering provides robust performance and outstanding marketing, sales and technical support.In-House Capabilities Provide Maximum Quality ControlFrom design to production, Parker’s many decades of hose engineering and manufacturing expertise ensure weldinghose products that meet needs and exceed expectations.Available When and Where Needed Parker inventories an extensive array of popular grades, sizes and lengths, supplemented by impressive customization capabilities, suchas special branding, fittings, lengths and packaging. Quick reaction times are standard for unanticipated sales opportunities and unexpected stock-outs. Quality, Service and Safety –the Parker PromiseSome welding hoses feature a soft,tacky cover, the result of materialsor production methods that minimizemanufacturing costs at the expenseof quality. Some welding hosemanufacturers close the door whenthe sale is completed, offering minimalpost-delivery support.But Parker provides quality, serviceand safety – a value-added packagethat no other welding hose suppliercan match. Throughout the industry,experienced welders trust Parkerto provide welding hoses and fittedhose assemblies that can do thejob – safely and effectively. Parkercontinues to honor that trust.All manufacturing processesoccur in Parker facilities:• specifying performance criteria• creating hose designs• specifying rubber formulations• mixing rubber compounds• d etermining appropriate brassfittings and componentry• manufacturing components• fitted hose assembly fabricationParker then rigorously tests theproducts to ensure they meetperformance requirementsand industry standards beforeleaving the factory.Welding Hose ApplicationsThe oxygen-fuel gas welding process, which produces flame at the tip ofa welding torch, is one of the most widely used welding processes. It remains popular because it is portable, versatile and relatively inexpensive. Common fuel gases include acetylene, hydrogen, natural gas, propane and propylene. The fuel gas provides the volatility and the oxygen enhances the temperature of the flame. These gases are transferred by specially designed hoses from a source – usually a tank or a manifold – to a welding torch or other apparatus. Regulators safely control pressure of the gases through the hose to the torch, where the gases are combined in specific proportions inside a mixing chamber.Oxygen-fuel gas welding is widely used for maintenance and repair applications such as bending, brazing, cutting, fabricating, gouging, joining,piercing, pre-heating, post-heating,severing, soldering, straightening,surfacing and trimming. Typicalindustries include construction,plant maintenance, foundries,manufacturing, maritime, mining,salvage/scrap and steel mills.Welding hose is also incorporated inconsumer/retail welding kits.Arc welding is a process that doesnot require oxygen or fuel gas.This process produces heat viaelectricity, which “arcs” (jumps)from the electrode in the torch to theweld piece. Arc welding frequentlyincorporates a shield gas (an inert/noble gas, such as argon) to “shield”the weld pool from airbornecontaminants. Some arc weldingequipment – such as automatic ormechanized applications – employswater-cooled torches. Consequently,many arc-welding systems requirehoses to convey the shield gases and/or water.Combination welding/cuttingequipment frequently providesoxygen-fuel gas capabilities combinedwith a plasma welding apparatus,where high electrical output createsan extreme amount of concentratedozone. This application frequentlyrequires abundant ventilation andGrade T single line welding hose toconvey the premium fuel gas andresist the extreme amounts of ozone(see Series 7141 / Series 7142 Grade Twelding hose).Parker has a complete industrialhose offering for welding andcomplementary applications.Fuel GasUse of any fuel gas other thanacetylene requires the use of Grade T hose. Due to safety concerns, CGA publicationsE-1 and SB-11 recommend the exclusive use of Grade T welding hose for all oxygen-fuel gas welding applications.Note: CGA recommends the exclusive use of Grade T welding hoseHoses used for welding service must meet industry standards that require special designs, materials and testing to safely convey combustible gases. The most commonly recognized welding hose standard in North America is jointly prepared by the Association for Rubber Products Manufacturers Association (ARPM) and the Compressed Gas Association (CGA). The standard is named ARPM IP-7, and was written for hose used with oxygen-fuel gas equipment for cutting, welding or other allied processes. The IP-7 standard categorizes welding hoses into three grades and four types:Oil ResistanceWhen exposed to an oilyenvironment, the cover of Grade R hose may become soft and tacky, leading to separation of the hose cover from the reinforcement, or excessive wear of the cover. Both of these conditions may lead to premature hose failure and/or decreased service life.• G rade T hose providesresistance to oil, both outer cover and internal tube • G rade RM hose provides resistance to oil, outer cover only • G rade R hose does not provide resistance to oilWelding Hose StandardsFlame ResistanceFlame-resistant welding hose will not be consumed and will self-extinguish within a specified period of time. Flame resistance provides significant safety advantages when subjected to adverse conditions such as flashbacks, hot slag or inadvertent exposure to flame.• G rade T hose providesresistance to flame, both outer cover and internal tube • G rade RM hose provides resistance to flame, outer cover only • G rade R hose does not provide resistance to flameFitted Hose AssembliesParker fitted hose assemblies meet the requirements of CGApublication E-1, “Welding and Cutting Equipment, Standard Connections for Regulator Outlets, Torches and Fitted Hose.”Compressed Gas Association – CGA ()E-1 Standard Connections for Regulator Outlets, Torches andFitted Hoses for Welding and Cutting Equipment SB-11Use of Rubber Welding HoseAssociation for Rubber Products Manufacturers – ARPM (https://)IP-7 Standard for Rubber Welding Hose IP-11-5 Guide for Use, Maintenance and Inspection of Welding Hose American National Standards Institute ()ANSI Z49.1 - Safety in Welding, Cutting, and Allied Processes* Including: acetylene, hydrogen, natural gas, propane and propyleneSafety Precautions in the Use of Rubber Welding HoseDO NOT• Abrade the cover of the hose • B end, kink or pinch the hose to shut off the flow of gas • D rag the hose over sharp edges or hot metal • E xpose the hose to flame, oil or sparks• Gouge the cover of the hose • H ang or pull the hose by the attached torch • L eave hoses pressurized when not in use • P ull equipment by using the hose as a tether• Recouple the hose ends • R epair the hose or hoseassemblies by using splicers, tape, or any other method • Reuse damaged hose • S train/stress the hose/fitting interface • U se adjustable clamps or bands to attach fittings to the hose (use permanently crimped ferrules)• U se or store hose in an area with inadequate ventilation • Use solvent to clean the hose • U se acetylene at any pressure above 15 psi • U se other fuel gases at any pressure above 40 psi • U se Grades R or RM hose with any fuel gas other than acetyleneDO• B low out residue from the interior of the hose prior to each use • E nsure that fittings arewrench-tight and leak-free prior to each use • E stablish a regular and systematic welding hosepreventative maintenance and replace-ment program • I nspect the entire length of the hose prior to each use• Perform periodic leak tests • P urge hoses of gas in a well- ventilated area when not in use for thirty minutes or longer • P urge hoses of gas by shuttingoff gas first at the torch and then at the regulator or supply source • R emove dirt and oil from the cover of the hose prior to each use (do not use solvent)• U se only fittings that are inaccordance with the Compressed Gas Association publication E-1• U se only ferrules to permanently secure fittings onto the hose • U se only ferrules that are a minimum of one inch long • G rade T hose is preferred for all fuel gases including actyleneEven with proper selection and instal-lation, hose life may be significantly re-duced without a continuing maintenance program. The severity of the application, risk potential from a possible hose failure, and experience with any hose failures in the application or in similar applications, should help determine the frequency of the inspection and the replacement of products. The safe use of welding hose requires the knowledge of the various hose grades, types, and attributes, including their com-patibility with various fuel gases and applications; the discipline to institute a comprehensive and thorough training, safety and maintenance program; and the awareness to seek, recognize and eliminate unsafe practices.For further information refer to:PERFORM FREQUENT WELDING HOSE INSPECTIONSREPLACE AND DISCARD DAMAGED HOSE OR HOSE ASSEMBLIESCompressed Gas Association – CGA ()E-1 Standard Connectionsfor Regulator Outlets, Torches and Fitted Hoses for Welding and Cutting Equipment SB-11 Use of RubberWelding HoseAssociation for Rubber Products Manufacturers – ARPM (https://)IP-7 Standard for RubberWelding Hose IP-11-5 G uide for Use,Maintenance and Inspection of Welding HoseBUL.4480-B218 12/2022© 2022 Parker Hannifin Corporation Your complete source for quality tube fittings, hose & hose fittings, brass & composite fittings, quick-disconnect couplings, valves, and assembly tools, locally available from a worldwide network of authorized distributors.Fittings:Available in inch and metric sizes covering SAE, BSP, DIN, GAZ, JIS, and ISO thread configurations, manufactured from steel, stainless steel, brass, aluminum, nylon, and thermoplastic.Hose, Tubing, and Bundles:Available in a wide variety of sizes and materials including rubber, wire-reinforced, thermoplastic, hybrid and custom compounds.Worldwide Availability:Parker operates Fluid Connectors manufacturing locations and sales offices throughout North America, South America, Europe, and Asia-Pacific.For information, call toll-free:1-800-C-PARKER (1-800-272-7537)Parker Fluid Connectors GroupNorth American Divisions & Distribution Service CentersNorth American DivisionsFluid System Connectors Division Otsego, MIphone 269 694 9411fax 269 694 4614Hose Products Division Wickliffe, OHphone 440 943 5700fax 440 943 3129Parflex Division Ravenna, OHphone 330 296 2871fax 330 296 8433Quick Coupling Division Minneapolis, MNphone 763 544 7781fax 763 544 3418Tube Fittings Division Columbus, OHphone 614 279 7070fax 614 279 7685Distribution Service CentersBuena Park, CAphone 714 522 8840fax 714 994 1183Louisville, KYphone 502 937 1322fax 502 937 4180Portland, ORphone 503 283 1020fax 503 283 2201Toledo, OHphone 419 878 7000fax 419 878 7001fax 419 878 7420 (FCG Kit Operations)Canada Milton, ONTphone 905 693 3000fax 905 876 1958(Contact Milton for other Service Center locations.)Parker Hannifin Corporation Hose Products Division 30240 Lakeland Blvd.Wickliffe, OH 44092phone 440 943 5700fax 440 943 **************************.com。

Parker Pneumatic 环保空气节约设备说明说明书

Air Saver UnitAn environmentally friendly solution to reducing air consumption.Contents PageFeatures ..................................................................................................... 3-4Speciﬁ cations ................................................................................................ 5Dimensions - ASV-200-AA-M5 ...................................................................... 6Dimensions - ASV-2000-AA ........................................................................... 7Dimensions - ASV-5000-AA ........................................................................... 8Dimensions - ASV-13000-AA .......................................................................... 9Dimensions - ASV-15000-AA ........................................................................ 10Dimensions - ASC500-1W / ASO500-1W ..................................................... 11Applications ............................................................................................. 12-13Selection of Air Saver Unit ........................................................................... 14Other Parker Energy Saving Products (15)For more information and videos visit: /pneu/airsaverImportant !Before carrying out any service work, ensure that the Air Saver Unit has been vented.Remove the primary supply air hose to ensure total disconnection of the air supply before dismantling valves or blank connection blocks.NB !All technical data in this catalog is typical only.The air quality is decisive for the valve life:see ISO 8573.WARNING FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF T HE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREINOR RELATED ITEMS CAN CAUSE DEA TH, PERSONAL INJURY AND PROPERTY DAMAGE.This document and other information from Parker Hanniﬁ n Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application including consequences of any failure, and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the ﬁ nal selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met.The products described herein, including without limitation, product features, speciﬁ cations, designs, availability and pricing, are subject to change by Parker Hanniﬁ n Corporation and its subsidiaries at any time without notice.Offer of SaleThe items described in this document are available for sale by Parker Hanniﬁ n Corporation, its subsidiaries or its authorized distributors. Any sale contract entered into by Parker will be governed by the provisions stated in Parker’s standard terms and conditions of sale (copy available upon request).© Copyright 2016 Parker Hanniﬁ n Corporation. All Rights Reserved!!!An easy solution to your environmental protection efforts!The Air Saver Unit contributes to power savings and CO 2 reduction.ASV2000 Series ASV5000 SeriesWhen using an Air Saver Unit several significant benefits can be achieved. Air blowing accounts for almost 50% of all compressed air used in plants. By using switching valve technology the Air Saver Unit can reduce air consumption by up to 50%!ASV200 SeriesASC/ASO500 Series • Large reductions in air consumption.• Savings in compressor power consumption.• Reduction in plant CO 2 emissions.• Big contribution to energy-saving activities.• Improved efﬁ ciency.VALUE IMPACT SUMMARYReduced Total Annual Air Discharge Per Blowing Nozzle (scfm) by:3,232,005Reduced Annual CO2 Emissions Generated (Per Blowing Nozzle - in Tons) by: 5.77 tons Reduced Annual Air Generating Costs Per Blowing Nozzle by:$ 892.03Quantity of Air Blowing Nozzles With Same Application Specifications 4Reduced Annual Air Generating Costs For All Nozzles by:$ 3,568.13Reduced Annual CO 2 Emissions Generated (For All Blowing Nozzles) by:23.07there is no air consumption.Energy/cost savingTry our fast and easy online savings calculator! /airsaverSampleApplication4nozzels 6mm dia.$0.10 / kWh1 min blow per 4 min cycle3 shifts 5 days /weekPrepared forPrepared byAir Saver Unit Valve CalculatorSummary Sheet✶ To achieve the benefi ts of pulsed air, the Air Saver Unit should be installed no more than 3 meters away from the air blow orifi ce. For optimal results install within 1 meter.Installation is simple and reduction in air consumption can be realized immediately.• W hen using an electrically operated solenoid valve to control the air blow, an Air Saver Unitcan quickly and easily be retroﬁ tted providing an immediate reduction in air consumption withno changes to the PLC program.Before introduction of the unit Before introduction of the unit After introduction of the unit• Easy to install. Change the current solenoid valve to Air Saver Unit. (ASC500 or ASO500)• Program change of controller is not necessary.• W hen using manual valves such as ball valves, simply install either ASV200, ASV500 orASV2000 units which do not need electrical power. Installing the unit brings immediate reduction in air consumption and improved compressor efﬁciency.[Company A] Food & Beverage manufacturer“When we tested ASV5000, we achieved about 55% reduction of our air consumption. Because air blow efﬁ ciency was improved, we plan to use more Air Saver Units in other areas in the plant”.[Company B] Manufacturer of ofﬁ ce document machines “We are working on energy-saving activities. In those activities,we decided to use an Air Saver Unit. We have more than 100points of air blow and we reduced our air consumption by 42% using this unit”.ts of ce. For optimal To achieve the benefi ts ofpulsed air, install no more than 3 meters away from the air blow orifi ce. For optimal results install within 1 meter.Speciﬁ cationParker PneumaticSpeciﬁ cationsASV200ASV2000ASV5000ASV13000ASC500ASO500Normally closedNon lubricated air459.1Notes:* External pilot of 43.5 - 116 is required, to ensure proper operation.†For maximum life of the unit we recommend 5 micron, but 40 micron ﬁ ltration is acceptable and will not void warranty.To achieve the benefi ts of pulsed air, the Air Saver Unit should be installed no more than 3 meters away from the air blow orifi ce. For optimal results install within 1 meter.Parker PneumaticPipingPort 1: Supply port (Compressor side)Port 2: Output port (Blow nozzle side)Port 3: Exhaust port** In order to keep out dust, the air mufﬂ er is recommended for exhaust port.ASV200-AA-M5Ordering Information ASV200-AA-M5Flow @ Port Operating Pressure Pilot air Dimensions: ASV200-AA-M5Notes:A. When temperature of valve goes below 5°C (41°F), complete dry air shall be supplied to prevent from freezing.B. Air Saver Units with WP prefix are suitable for mostpainting applications. Test before use if in direct contact with painted surface.C. If test in painting application fails, try cycling Air Saver Unit for 48 hours and repeat test.D. DO NOT use “WP” Air Saver Unit in ‘clear coat’ applications.E. Adjustable to maximum frequency of 5Hz.Port 2 - 3/8 PluggedPort 4 - 3/8Pilot air supply port M5Mounting holeOFF timeadjustment needle ON timeadjustment needlePort R2 - 3/8 PluggedThreshold elementPort 3 -3/8 pluggedPort 1 - 3/8 supply3 x ø 0.280.980.981.181.181.893.192.541.180.590.79Max 0.610.202.132.683.230.040.59PipingPort 1: Supply port (Compressor side)Port 2: PluggedPort 3: PluggedPort 4: Output port (Blow nozzle side)Port R2: PluggedPort X: M5 pilot air supply>43.5 psi is requiredOrdering Information ASV2000-AA-xxFlow @ Port Operating Pressure Pilot air PortDimensions: ASV2000-AA-97 (NPT model)Notes:A. When temperature of valve goes below 5°C (41°F), complete dry air shall be supplied to prevent from freezing.B. Air Saver Units with WP prefix are suitable for most painting applications. Test before use if in direct contact with painted surface.C. If test in painting application fails, try cycling Air Saver Unit for 48 hours and repeat test.D. DO NOT use “WP” Air Saver Unit in ‘clear coat’ applications.E. Adjustable to maximum frequency of 5Hz.(E)PipingPort 1: Supply port (Compressor side)Port 2: Plugged Port 3: PluggedPort 4: Output port (Blow nozzle side)Port 5: PluggedPort X: M5 pilot air supply >43.5 psi is requiredOFF timeOrdering Information ASV5000-AA-xxFlow @ Port Operating Pressure Pilot air Port Dimensions: ASV5000-AA-91 (NPT model)(E)Notes:A. When temperature of valve goes below 5°C (41°F), complete dry air shall be supplied to prevent from freezing.B. Air Saver Units with WP prefix are suitable for most painting applications. Test before use if in direct contact with painted surface.C. If test in painting application fails, try cycling Air Saver Unit for 48 hours and repeat test.D. DO NOT use “WP” Air Saver Unit in ‘clear coat’ applications.E. Adjustable to maximum frequency of 5Hz.PipingPort 1: Supply port (Compressor side)Port 2: Output port (Blow nozzle side)Port 3: PluggedPort X: 1/8 NPT pilot air supply >43.5 psi is requiredONX PortPilot air port 1/8 NPTOFF timeadjustment needle ON timeadjustment needle4 x ø 0.43(Mounting hole)1A33.863.034.412OFF 2.321.633.720.355.164.653.940.678.272.682.322.010.310.790.791.165.87Port 1, 2, 3 (3 x 1 NPT)AOrdering Information ASV13000-AA-xxFlow @ Port Operating Pressure Pilot air Blow PortDimensions: ASV13000-AA-94 (NPT model)(E)Notes:A. When temperature of valve goes below 5°C (41°F), complete dry air shall be supplied to prevent from freezing.B. Air Saver Units with WP prefix are suitable for most painting applications. Test before use if in direct contact with painted surface.C. If test in painting application fails, try cycling Air Saver Unit for 48 hours and repeat test.D. DO NOT use “WP” Air Saver Unit in ‘clear coat’ applicationsE. Adjustable to maximum frequency of 1Hz.PipingPort 1: Supply port (Compressor side)Port 2: Plug (1-1/4) Port 3: Plug (1-1/4)Port 4: Output port (Blow nozzle side)Port 5: Plug (1-1/4)Port X: 1/8 NPT pilot air supply >43.5 psi is requiredONPort 4 -1-1/4 NPTOFF timeadjustment needleON timeadjustment needle4 x ø 0.43 (Mounting hole)Port 1 -1-1/4 NPT0.792.288.03OFF 4.210.432.403.665.676.61X PortPilot Air supply 1/8 NPT2.952.28Port 2Plug8.981.141.14Port 3PlugPort 5Plug 3.905.671.180.982.28Ordering Information ASV15000-AA-xxFlow @ Port Operating Pressure Pilot air Port Dimensions: ASV15000-AA-92 (NPT model)(E)Notes:A. When temperature of valve goes below 5°C (41°F), complete dry air shall be supplied to prevent from freezing.B. Air Saver Units with WP prefix are suitable for most painting applications. Test before use if in direct contact with painted surface.C. If test in painting application fails, try cycling Air Saver Unit for 48 hours and repeat test.D. DO NOT use “WP” Air Saver Unit in ‘clear coat’ applications.E. Adjustable to maximum frequency of 1Hz.Parker PneumaticPipingPort 1: Supply port (Compressor side)Port 2: Output port (Blow nozzle side)Y port: Pilot exhaust port** In order to avoid dust, it is recommended to attach an air mufﬂ er.ASC500-1W / ASO500-1WOrdering Information ASC500-1W / ASO500-1WFlow @ Port Operating Pressure Pilot air Dimensions: ASC500-1W-90 / ASO500-1W-90 (NPT model)Port 21/8 NPTASC Version OnlyASO Version Only 2 x Ø7.57.51515Wiring Specifications1: Continuous blow ON (−)15.5Port Y: M5ASC OnlyPort 11/8 NPTPort Y: M5ASO Only7.57.515.5(B)Notes:A. When temperature of valve goes below 5°C(41°F), complete dry air shall be supplied to prevent from freezing.B. Adjustable to maximum frequency of 22Hz.Cleaning blow before assemblySwarf removalAssist blow for PET bottle transferLiquid removal after the manufacturing processCan be used in many applications where air blow is a requirementDrying ApplicationsSwarf RemovalCooling ApplicationIonizer Dust RemovalPET Bottle TransferCar PaintingProcessPaint spraying *Electrical parts* Air Saver Units with WP preﬁ x are suitable for most painting applications. Test before use if in direct contact with painted surface. If test in painting application fails, try cycling Air Saver Unit for 48 hours and repeat test. DO NOT use “WP” Air Saver Unit in ‘clear coat’ applications.Air Saver UnitPneumatic Solutions for Beverage and Bottle Plants molded PET bottles.Escape blow for PET bottles when the line is stopped.date on them.Selection of Air Saver UnitGuide data for the correct selection of an Air Saver Unit for blow applications.Please take into account the two variables:• System operation pressure (PSI)• Required air consumption of nozzle or set of nozzles (scfm) to be controlled with one Air Saver Unit Color coding indicates correct Air Saver UnitReduced performance flow capacity of 10% is applied Consider min. operating pressure (see tech specs on page 5)Consider min. pilot air pressure (see tech specs on page 5)Nozzle area (mm2)0.00.00.10.20.81.83.17.112.619.628.335.850.263.678.595.0113.0132.7153.9176.6201.0226.9254.3283.4314.0346.2379.9415.3452.2490.6ASV200ASC500/ASO500ASV2000ASV5000ASV13000ASV15000Other ParkerEnergy Saving Productsand Tools PortfolioWear CompensatedSeals• Air valve spools that havewear compensation• Air pressure forces the sealsout to the valve bore.• Very little air leakage acrossthese spools through outit’s life.• Especially better than lappedspool valves.Pressure DifferentialSensors• Monitor pressure dropon ﬁ lters.• Provide electrical signalsor visual indicators whenpressure drop is high andﬁ lter elements need replaced.• Can assist you in loweringcompressed air costs byreducing pressure drops.Straight Fittings,Pre-Sealed• Factory applied threadsealant perform better thanoperator applied sealant.• Where ever possible,use straight ﬁ ttings inplace of 45 or 90 degreeelbow ﬁ ttings to minimizepressure drop and save oncompressed air costs.Zero Loss Air Drains• Many Compressors and AirTanks use Timer Drains topurge water and moisturefrom the tanks.• Timer Drains wastecompressed air becausethey blow too long, and blowwhen no water is present.• Zero Loss Drains use ﬂ oatsto actuate the drain to openand blow out moisture andshut off once moisture isgone, saving compressedair costs.Pneumatic Sizing Tools• Air Cost, Flow, and ProductSizing Calculators• Conversion tools (e.g.Pressure BAR to PSI)• Available on website,downloadable for cellphones and I Pads fromApple App Store.Air EconomizingVacuum Generators• Built-in sensors onlyapply air pressure whenvacuum is needed.• Sensor turns generatoron when vacuum dropsto a preset level.• Reduces plantcompressed air costs.Low Power Solenoids• Typical Class 8 22mmCoil Wattage 5.4W• Parker 15mm CoilWattage 1.2W• Save 4.2W whiledoing workReverse Flow Regulators• Most actuators only needwork force in one direction.• Installed between valveand actuator.• Reduces pressure on thereturn stroke of an actuatorwhere work force is notneeded.• Reduces plant compressedair costs.Catalog 0698P 06/2016Applications EngineeringPhone: 877 321 4PDN Option #2E-mail:******************Customer SupportPhone: 877 321 4PDN Option #1Parker Hannifi n Corporation Pneumatic Division 8676 E. M89P .O. Box 901Richland, MI 49083 USA。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

在工厂设备维修和安装过程中,常需要各种不同类型和尺寸的管道接头,管道接头由黄铜制成,表面镀镍.螺纹符合ISO 7 (BSPT),ISO 228(BSPP)及SAE AS 71051:1999 (NPT)Maintenance of equipment in the factoryand the installation process, often needdifferent types and pipe joints, pipe jointsmade from brass, nickel-platedPSM PSF PSMF PMB POM PSL PO POHPN PAD PEL PEFL PFL PMF PMTPMFS PMSF PMSM PMS PFC PYF PYMPART NO.L1L2L3CHInfo Thread1 Thread2 PSM R1/8 R1/8 20 7.5 7.5 12 R1/8 R1/4 23.5 7.5 11 14 R1/8 R3/8 24 7.5 11.5 17 R1/4 R1/4 27 11 11 14 R1/4 R3/8 27.5 11 11.5 17 R1/4 R1/2 31 11 14 22 R3/8 R3/8 28 11.5 11.5 17 R3/8 R1/2 31.5 11.5 14 22 R1/2 R1/2 34 14 14 22 R1/2 R3/4 37.5 14 16.5 27R3/4R3/44016.516.527PART NO.L1 CH Info Thread1 Thread2 PSF M5*0.8 M5*0.8 11 8 M5*0.8 G1/8 13.5 14 G1/8 G1/8 15 14 G1/8 G1/4 19 17 G1/8 G3/8 20 22 G1/4 G1/4 22 17 G1/4 G3/8 22.5 22 G1/4 G1/2 26 24 G3/8 G3/8 24 22 G3/8 G1/2 26 24G1/2G1/23027PART NO.L1 L2 CHInfo Thread1 Thread2 PSMF G1/8 R1/8 18 8 14 G1/4 R1/8 22 8 17 G1/4 R1/4 25 11 17 G3/8 R1/4 26 11 22 G3/8 R3/8 26 12 22 G1/2 R1/4 29 11 24 G1/2 R3/8 30 12 24G1/2R1/2321426PART NO.L1 L2 CHInfo Thread1 Thread2 POM R1/4 G1/8 16 11 14 R3/8 G1/4 17 12 17 R3/8 G1/8 17 12 17 R1/2 G1/8 20 14 22 R1/2 G1/4 201422 R1/2 G3/8 20 14 22R3/4G1/2241727PART NO.L1 L2 CHInfo Thread1 Thread2 PMB M5*0.8 M10*1 13 9.5 14 G1/4 M16*1.5 19 15 22 G1/4 M20*1.5 23 19 27 G3/8 M26*1.5 27 22 32G1/2M28*1.5342836PART NO.L1 L2 CHInfo Thread1 Thread2 PSL-22 G1/8 G1/8 22 6 14 PSL-42 G1/8 G1/8 42 6 14 PSL-35 G1/4 G1/4 35 8 17 PSL-51G1/4G1/451817直通,外螺纹,Male , Taper or Parallel直通,内螺纹,Female , Parallel直通,内-外螺纹,Adaptor Male-Female ,Taper变径,内-外螺纹,Taper Male-Female Reducer穿板直通,Bulkhead 加长直通,内-外螺纹, Extention Male-FemalePART NO.L1 L2 CHInfo Thread PO M5*0.8 8.5 5 8 G1/8 10 6 14 G1/4 13 8 17 G3/814 9 19G1/2161024PART NO.L1 L2 CHInfoThread POH G1/8 9.5 6.5 5 G1/4 12 8 6 G3/8 13 9 8G1/2141010PART NO.L1 CHInfo Thread PN G1/8 12 14 G1/4 15 17 G3/8 16 20G1/220 24PART NO.L1 L2 CHInfoHoseThreadPAD 3 M5*0.8 17 5 8 3.5 M5*0.8 17 5 8 4.5 M5*0.8 17 5 8 7.5 G1/8 30 6 14 7.5 G1/4 33 8 17 8.5 G1/8 30 6 14 9.5 G1/8 30 6 14 9.5 G1/4 33 8 17 9.5 G3/8 34 9 19 12.5 G1/4 35 8 17 12.5 G3/8 36 9 19 12.5 G1/2 38 10 24 17.5 G3/8 38 9 1917.5G1/240 10 24PART NO.L1 L2 L3 CHInfo Thread PEL R1/8 18.5 18.5 8 10 R1/4 23.5 23.5 11 13 R3/8 26 26 12 17R1/231 31 14 21PART NO.L1 L2 L3 CHInfo Thread1 Thread2PEFL R1/8 G1/8 21 18.5 8 10R1/4 G1/4 25.5 23.5 11 13 R3/8 G3/8 28 26 12 17R1/2G1/2 34 31 14 21PART NO.L1 L2 CHInfo Thread1 Thread2 PFL G1/8 G1/8 21 21 10 G1/4 G1/4 25.5 25.5 13 G3/8 G3/8 28 28 17G1/2G1/2 34 34 21PART NO.L1 L2 CHInfo Thread1 PMF G1/8 42 21 10 G1/4 51 25.5 13 G3/8 56 28 17G1/2673421外六角堵头,Male Plug, Taper or Parallel内六角堵头,Male Plug With O-ring柱塞帽,Female Plug 软管接头,Hose Conncector , Taper or Parallel直角,外螺纹, Male-Male Elbow直角,内-外螺纹, Female-Male Elbow直角,内螺纹, Female-Female Elbow三通,内螺纹, Female TeePART NO.L1 L2 L3 CHInfo Thread1 Thread2 PMT G1/8 R1/8 42 18.5 8 10 G1/4 R1/4 51 23.5 11 13 G3/8 R3/8 56 26 12 17G1/2R1/267311421PART NO.L1 L2 L4 CHInfoThread1 Thread2PMFS R1/8 G1/8 18.5 21 8 10R1/4 G1/4 23.5 25.5 11 13 R3/8 G3/8 26 28 12 17 R1/2G1/2 31 34 1421PART NO.L1 L2 L3 CHInfo Thread1 Thread2 PMSF G1/8 R1/8 21 18.5 8 10 G1/4 R1/4 25.5 23.5 11 13 G3/8 R3/8 28 26 12 17 G1/2R1/2 34 31 14 21PART NO.L1 L2 L3 CHInfoThread1 Thread2PMSM R1/8 G1/83721 8 10 R1/4 G1/4 47 25.5 11 13 R3/8 G3/8 52 28 12 17 R1/2G1/262341421PART NO.L1 L2 L3 CHInfo Thread PMS R1/8 37 18.5 8 10 R1/4 47 23.5 11 13 R3/8 52 26 12 17R1/262311421PART NO.L1 L2 CHInfoThread PYF G1/8 14 12 13 G1/4 17 14 17 G3/8 19 16 20G1/2251925PART NO.L1 L2L3 CHInfo Thread1 Thread2 PYM R1/8 G1/8 14 16 8 13 R1/4 G1/4 17 20 11 17 R3/8 G3/8 19 22 12 20R1/2G1/22527 14 25PART NO.L1 L2 CHInfo Thread PFC G1/8 42 42 13 G1/4 51 51 17 G3/8 56 56 20G1/2676725三通,内-外-内螺纹, Female-Male-Female Stud Tee三通,内-内-外螺纹, Female-Female-Male Lateral Tee三通,外-外-内螺纹, Male-Male-Female Tee 三通,外-内-外螺纹, Male-Female-Male Tee三通,外螺纹, Male Tee Y 型,内螺纹, Female YY 型,内-外螺纹, Female-Male Y 四通,内螺纹, Female Cross。