化妆盒移动电源
移动电源使用说明书
移动电源使用说明书本品是一款便携式高容量数码移动电源：GOPO采用高性能聚合物电芯，容量可达到\5000mAh，它兼具充电器和后备电池的双重功能，采用USB输出，通过选配放电输出线加转接头，可以给平板电脑，手机,电子书，游戏机,数码相机DVD IPOD，IPHONE，IPAD，PDA,MP4,MP5,PMP，PSP等带USB充电的设备充电；充电方式采用电脑USB对其充电，使用起来非常方便，随时随地为您解决设备没有电的烦恼产品具体参数：产品型号： GOPO输入：5V/1A输出1：5.4V/1.5A 输出2：9.5V 1.5A容量：聚合物电池5000mAh充电时间： 4-5小时循环寿命：＞500次,8-10年时间工作温度： -10℃-40℃储存，运输温度：-20℃-50℃体积： 125*70*13mm净重： 140克毛重：250克包装：380*315*240mm 毛重：44台*250克携带方式：放在旅行背包，电脑包里或放在车里电量显示： 4级LED灯显示电量.非工作状态智能自动关机充电显示：充电时0-25% 一个灯闪亮，其它灯不亮，充电到25%--50% 时，第二灯闪，第一灯变为恒亮，充电到50%-- 75% 时第三个灯闪亮，前面二个灯转为恒亮，充电到 75%---100% 第四个灯闪亮，前面三个灯转为恒亮，四个灯全亮充电到 100%充电方法：使用原装的电源适配器加上标配的充电转接头对本产品直接充电适用设备：可以给所有带USB充电的设备使用，如平板电脑，学习机，手机，PSP，IPOD，IPHONE，IPAD，MP4，PMP,GPS,蓝牙，数码相机等。
操作使用方便1.选好与数码产品相对应的电压2.选好要用的数码产品对应的转换头3.将选好的转换头插入你所用的数码产品上4.精确显示电池电量5.超长使用寿命6.无记忆效益7.超长循环次数。
可达500多次循环。
即使到达500多次以后仍可保证80％以上的电量8.具有安全可靠性9.本产品采用国际领先科技的进口锂电池，具有环保，安全，无毒危险10.智能自动短路保护设计，所有接座均具有短路保护功能注意事项1.请勿将输出电压调整到高于设备电压，否则有可能引起设备损坏，请在使用前一定确认清楚2.请使用指定充电器3.禁止短路，分解和抛入火中4.不得擅自拆卸充电器和电池对其进行改造5.注意防潮防水Mobile power supply manualThis product is a portable high-capacity digital mobile power: GOPO high-performance polymer batteries, the capacity can be achieved \ 5000mAh, which combines the dual function of the charger and battery backup, using the USB output, through the optional discharge the output line. computer USB charging adapter, charge; charging mode to tablet PCs, mobile phones, e-books, game consoles, digital cameras, DVD IPOD, IPHONE, IPAD, PDAs, MP4, MP5, the PMP, PSP and other devices with USB charging , very convenient to use anywhere, anytime to solve your equipment without electricity troublesSpecific parameters:Product Model: GOPOInput: 5V/1AOutput 1:5.4 V/1.5A output 2:9.5 V-1.5ACapacity: Polymer battery 5000mAhCharging time: 4-5 hoursCycle life:> 500 8-10 yearsOperating temperature: -10 ℃-40 ℃Storage and transport temperature: -20 ℃-50 ℃Dimensions: 125 * 70 * 13mmNet weight: 140 g Gross Weight: 250 gPackaging: 380 * 315 * 240mm GW: 44 units * 250 gCarrying methods: on the travel bag, computer bag, or in the carPower display: four LED lights to display power. Non-working status of the intelligent automatic shutdownCharge: charging 0-25% of a light shining, the other lamp is not lit, charging to 25% - 50%, the second light flash, the first light into constant light, the charge to 50% - 75% when the third light flashes in front of two light became lit, charging to 75% --- 100% the fourth light flashes in front of three lights became lit, four full bright light to charge to 100 % Charging method: using the original power adapter with standard charging adapter direct charge of the productApplicable devices: all devices with USB charging, machine learning, such as tablet PCs, mobile phones, the PSP, IPOD, IPHONE, iPad, MP4, PMPs, GPS, Bluetooth, digital cameras and so on.Easy to operateSelecting the voltage corresponding to the digital productsSelected to use digital products corresponding to the conversion head3 will be selected adapter into your digital productsAccurately display the battery power(5) Long life6. Memory efficiencyLong cycle times. Up to 500 cycles. Even reached 500 beyond, to ensure that more than 80% of electricity8 with the safety and reliabilityThis leading international technology imported lithium batteries, environmentally friendly, safe, non-toxic hazardsThe intelligent automatic short circuit protection design, all access seat are short circuit protectedNoteDo not output voltage adjusted to higher than the voltage of the device, or they may cause damage to the equipment, please be sure that before usingPlease use the specified chargerProhibit short circuit, decomposition, and into the fire(4) shall not disassemble charger and battery to transformNote that the moisture waterproof移动电源怎么用拥有了移动电源，就会开始使用移动电源。
wopow沃品4400mAh安心移动电源PD001使用说明
型号：PD001用户手册DC 5V 本产品适用于-输入的电子数码产品充电00mAh安心 移动电源 44Wopow ○R Safety Portable Power Supply 4400 mAhUser ManualModel Number: PD001This product is used for Charging DC-5V input Electronic Digital Product一、产品简介ⅠProduct Introduction:本产品为移动备用电源。
输入端为Micro 5pin USB 接口，内置进口三星18650可充电锂电池，总容量为4400mAh ，充电电流为1000mA Max ；输出端为标准 2.0 USB 接口，输出规格为5V 1000mA Max 恒压限流。
This product is portable backup power supply. Input termianl is Micro 5pin USB interface, built-in imported Samsung 18650 rechargeable Lithium battery, total capacity is 4400mAh, charge current is 1000mA Max; output terminal is Standard 2.0 USB interface. Output standard: 5V/1000mA Max, constant-voltage & limitary-current可随时随地对您的IPAD 、IPHONE 、MP3、MP4等数码产品进行充电，解决无电的烦恼。
使用前请仔细阅读说明书。
Charging your IPAD 、IPHONE 、MP3、MP4 and other digital products at any time and any place, to solve the power-off trouble. Please read the instruction carefully before usage二、部件识别ⅡStructure of componentsUSB 输出小电筒4档电量1. 4 level indicator light2. Power Indicator Light button3. LED flashlight4. USB output interface5. Micro Input Interface三、使用说明Ⅲ Usage instruction1.LED 小电筒使用:长按按键2秒,LED 小电筒打开;再长按按键2秒, LED 小电筒关闭.满电状态,使用LED 小电筒照明可长达100H 以上。
AA胶电池可移动电源产品说明书
Energy Management System Operation ManualPlease read this manual before attempting to install or operate any of theEMS system components. AA Portable Power Corp. will not be responsiblefor any problem due to misusing.Catalogue1Introduction: (3)2Specification (3)3Typical diagram: (4)4Heart Beat LED (5)5Isolate Battery & Shunt connection: (6)612V Power: (6)7Monitor Page select switch: (7)8Sense Board Wiring: (7)9Battery balancing (9)10Video Output (10)11Can Bus Output (Optional) (10)12Main Screen: (11)13Individual Cell Page (12)14Alarms： (13)15Controlling Devices with Alarm Outputs (14)16Capacity Algorithm (14)17Ground Fault Detection (15)18Trouble Shooting (16)1Introduction:Thank you for purchasing Energy Management System (EMS). This manual covers the operating and installation information for this systemThe EMS system has everything needed to display the condition and maintain the health of lithium ion batteries and is specifically designed to work with GBS Lithium Ion batteries.The system consists of two major components, the computer Master (MASTER) and the cell sense boards. The MASTER shows details about the condition of the battery pack, such as current, voltage, state of charge and individual cell details, via its video output display. The sense boards form a simple daisy chain by mounting on each cell to read voltage and temperature; they also perform battery balancing during recharging to equalize the charge within the battery pack. Two alarm outputs, one for over voltage and one for under voltage, provide automatic shut off signals to prevent overcharging or over discharging of the battery pack. A unique feature of the EMS system is ground fault detection. High voltage systems should be floating relative to the chassis for safety. If an inadvertent path to the chassis ground is made the system will detect it and display a warning for this unsafe condition. The EMS outputs composite video to display battery pack information. A CAN (controller area network) interface option is available to output the information from the EMS to other systems.2Specificationoutputs3Typical diagram:The EMS is designed to make installation as easy as possible. All of the connections to it are made with convenient pluggable ¼” quick disconnect terminals. The EMS Master should be installed as close to the shunt as possible. The shunt sense wires should be less than 1’ long. A mounting template for the computer is shown in Appendix A. After the installation is complete, the battery pack must be completely charged before the capacity will read correctly (see Section 7.Capacity Algorithm for more details).Note: The EMS system components utilize either a conformal coating or rubberized coating on all components to allow them to perform in high humidity environments. They are not however water proof. All components must be installed inside water resistant containers.4Heart Beat LEDWhen the EMS is correctly connected to 12V, the heartbeat indicator will blink once per second5Isolate Battery & Shunt connection:The Terminals on the left side of the Master are used for making the High-Voltage and shunt connections. Refer to the figure below for these connections. The connections between the battery pack, shunt and high voltage loads are usually large wire (e.g. 2/0 depending on the max current of the system).The connections to the EMS from the battery and the shunt can be smaller gauge (e.g. 18 or 20 Awg).Note: Please use extreme caution when making these connections as the full battery pack potential will be present between the shunt and battery pack positive pins. Connecting these wires incorrectly can cause damage to the EMS MASTER which will not be covered under warranty.The wires connecting to the shunt should be a twisted pair or wires with as short of a distance from the MASTER as possible to achieve accurate measurements.612V Power:The MASTER is powered by 12 volt s, which is connected to the terminals marked “12V”and “GND”. This should be connected to a power source through a 5A fuse. The power can either be always on, or can be switched off to conserve power. 12 volt power must besupplied at any time when the battery pack is being charged or discharged. When 12 volt power is applied the red heartbeat LED will blink.If the battery pack is more than a 12 volt battery, and the MASTER is to be powered off of it,a DC/DC converter must be used so that the battery pack is discharged equally. Under nocircumstances can four cells within the battery pack be tapped for 12 volt power for the MASTER as this will cause an imbalance within the battery pack.Note: T here are three pins marked “GND” for ground on the MASTER. These three pins are common together. Only one of these pins needs to be connected, the other two are located for convenient connection options. It is not chassis.7Monitor Page select switch:To change the display on the MASTER to the individual cell screen(s) a normally open momentary switch is used to short the pins marked (MDE) to (GND). There is no polarity to the switch and the connection can be small gauge wire (e.g. 18 Awg). In applications where the 12 volt power is grounded to a vehicle chassis only one wire needs to be ran from the MDE pin and can be grounded to the chassis through the momentary switch.8Sense Board Wiring:The sense boards are connected to the MASTER via a cable with five pins. Depending on which sense board version the system was supplied with this cable will have either four or five wires connected to it. This connector has a retention mechanism. If removal of this cable is needed never pull in the wires, always pull up on the connector, to avoid damage to the wire harnessThe MASTER will automatically index the sense boards based on their position in the daisy chain of sense boards. The first sense board connected to the MASTER will be cell number one and will count up from there. It is recommended that the negative most cell in the pack be made cell number one and have the daisy chain move toward the most positive cell in the pack. This will aide in troubleshooting if needed; however, the sense boards can be connected in any order.Before installing sense boards, install all cell jumpers first with the outer two screws tightened. Never install sense boards underneath jumpers as this will cause current to flow through the screws, which is a poor connection. Never slide a jumper underneath a sense board while installing as this may cause a short with components which are located on the back of the sense board.When installing sense boards, keep cell covers installed on all cells except the cell where the sense board is being installed. Do not allow sense boards to lie on battery terminals. This will help prevent accidental damage to sense boards during installation.The sense boards have an input and an output connector. Before installing, ensure that they are oriented in the appropriate direction. The male connector is the input; the female connector is the output.The sense boards have battery positive and negative indicated on them. Ensure that the polarity is correct before installing. The boards will not be damaged by a reverse polarity; however, they will not function. When a sense board is installed correctly the green LED will light up. There is also a red LED on the sense board, which indicates cell balancing is occurring.This led will light up any time the cell voltage is 3.55V or higher.Note: The sense boards, like the cells they attach to, alternate + and – for the series connection. The last string in the daisy chain is not terminated and will have its output connector not connected to anything. Should the installation have less than an even multiple of 4 cells, the cable may be cut close to the last sense board used. Be sure to cut the cable cleanly with no wires left exposed. Do not cut the cable with 12V power applied to the MASTER! The resulting short circuit may damage the EMS computer.9Battery balancingWhen the battery voltage rises during charging to 3.55V or above the red balancing LED will light on the sense board to indicate the cell is balancing. The sense boards will draw 0.5A until the voltage has dropped below 3.55V. It is normal for some cells to balancemore than others and some cells to rarely balance.10 Video OutputThe EMS MASTER outputs composite video output through a common RCA type jack. This can be connected to the optional LCD screen EPS provides or any other display which will accept this type of input (e.g. in dash DVD). The video cable is not provided as length requirements vary. A shielded cable is recommended if there is snow or static in the video signal11 Can Bus Output (Optional)If your MASTER has the optional CAN bus interface this connector will be on the side of the MASTER.12 Main Screen:When properly installed, the EMS system will display the Voltage, current, capacity and alarm status of a Lithium Ion battery pack. This is an example of what the main screendisplays:Number of Cells is indicated at the top of the screen as “E.M.S –x” where x is the number of sense boards the MASTER has been programmed to manage. If the system detects a value other than this it will trigger an unmanaged cell alarm.Battery Pack Voltage is the total battery pack voltage. This updates in real time and the numerical value is displayed below the bar. This bar will be green whenever voltage is between 3.0V x N (the number of cells in the pack). When the voltage drops below 3.0V x N the bar will turn red to indicate low voltage. The bar will also turn red when the voltage rises over 3.4V x N to indicate that the target charging voltage range has been attained. If the voltage goes outside of the range of the bar and off scale message will appear.Battery Pack Current is the current either being drawn from the battery or being recharged into it. Like the voltage bar this is indicated in real time and the numerical value is displayed below the bar. This bar will be green and will turn red when current is above 200A. When current is negative and the battery is being charged this bar will turn white and “Charging” will be displayed.Battery Pack Capacity is the battery state of charge. It works by tracking the amount of charge that goes in and out of the battery pack. It will reset to 100% during charging when the current is within a normal charging range for a battery charger and the total battery pack voltage reaches 3.52 x N (the number of cells). When the system is powered up for the first time this value will read 50%. The battery will have to be charged to full in order to reset the capacity reading correctly to 100% the first time.Min/Max Cell Voltage provides a quick overview of the maximum and minimum cell voltages within the battery pack. Depending on the number of cells within the battery pack, these values update every 1 -2 seconds.Alarms and Warnings are displayed at the bottom of the screen after the word “Pack:”.There are seven alarms:- Over voltage (highest cell is over 3.8V after a 3 second delay)- Under voltage (lowest cell is below 2.8V after a 30 second delay)- Over current (current exceeds 10C for 10 seconds)- Over temperature (highest cell exceeds 150°F or 65°C)- Under temperature (lowest cell is below 32°F or 0°C, charging is not allowed)- Ground fault (There is a high voltage leakage greater than 2mA to the chassis pin)- Unmanaged cells (The programmed number of cells does not equal the number of cells read)13Individual Cell PageTo access the individual cell detail page(s) refer to section 7, Page Select Switch Input.When momentary switch is pressed and released it will change the display to show the first20 cells in the pack with details of voltage and temperature of each cell as shown below:If there are more than 20 cells in the pack pressing the button again will advance tothe next 20 cells until the last cell page is reached, then pressing the button againwill return to the main screen.Cell (number) is the location of the sense board relative to the daisy chain of sense boards. The cell connected to the MASTER first is number one.Volts is the actual cell voltage. This updates every 1-2 seconds, depending onthe number of cells in the pack.Temp is the temperature reading. This updates every 1-2 seconds, depending on the number of cells in the pack. The number will turn red if the cell exceeds the upper temperature limit. Readings are in °F by default; however, upon request, this can be set to read in °C.The cell temperature is measured at the positive terminal of each sense board. If a single cell has noticeably higher temperature during use than other cells, but the temperature goes back down quickly this may be an indication of a poor connection where there is high contact impedance. Also, during balancing the temperature will temporarily rise due to the energy being converted to heat.Note that this screen will not automatically update if more or less cells are connected during installation. To update the screen the Page Select buttonmust be pressed until it has cycled back through the main screen, then back tothe individual cell detail screens in order to update the view. Cell voltage and temperatures are updated in real time on these screens.14Alarms：In order to protect the battery pack there are a number of alarms, which are based on cell voltage, temperature and pack current and fault conditions. The MASTER contains two alarm output pins, UV for under voltage and OV for over voltage. When any of the alarm conditions are met for a specified duration of time they will activate their respective action listed in the table below:The alarm limit values may vary with special request configurations.The same delay time must elapse once an alarm condition is cleared to deactivatethe alarm.15Controlling Devices with Alarm OutputsThe alarm outputs on the MASTER output 12 volts and can drive continuously 2A with up to a 4A surge. Exceeding these limits or short circuiting these pins may cause damage to the MASTER. The alarms act according to the above table. It is very important that these alarm outputs be able to disconnect the battery pack from loads and charging sources when they activate; this must be a no parasitic load condition to fully protect the battery. Ensure that items such as controller pre- charge resistors, DC/DC converters, lights, etc. are all disconnected in the event that the low voltage alarm triggers. Failure to properly implement these alarm interlocks may void the warranty on the battery.When all parameters are within normal ranges these alarm outputs will be 12 volts. They will drop to 0 volts during an alarm condition. When power to the MASTER is removed these outputs will not supply power. Systems should be designed such that they require power from the alarm outputs from the MASTER in order to function.16Capacity AlgorithmThe EMS MASTER keeps track of the capacity of the battery pack by tracking current in and out of the battery (coulomb counting). There are however several corrections built in to the software to ensure that the capacity stays accurate over time.The capacity will reset to 100% if the following conditions are met:- Total pack voltage measures 3.52V x N (N being the number of cells) when being charged by a battery charger.The capacity will reset to 100% if the following conditions are met:- The over voltage alarm is triggered when being charged by a battery charger, see default alarm table for set points.The capacity will reset to 0% if the following conditions are met:- The under voltage alarm is triggered and discharging current is not excessive, see default alarm table for set points.When the EMS is powered up the first time the capacity will read 50%, which is approximately the state of charge that the batteries ship at when new. To sync the capacity the first time the battery pack must be charged full, which will trigger a reset to 100%.The capacity measurement is done based on the programming in the MASTER. MASTER’s cannot be interchanged with one which has been programmed for a different battery pack configuration.Upon special request the MASTER can be programmed to extend battery life by limiting the depth of discharge to 80%. This will scale the capacity bar such that 100% of the scale is 80% of the battery capacity. Once the capacity reaches 0%, which is 20% of the actual capacity remaining, the under voltage (UV) output will automatically shut off.17Ground Fault DetectionThe pin marked “Chassis” is used for the ground fault detection circuitry integrated in to the EMS MASTER. This should be connected to its own dedicated chassisground point. When this is done and the shunt and battery positive wires areconnected properly the system will be able to detect a ground fault anywhere within the battery pack. This feature will display an alarm message on the screen if there is a fault condition, but will not cause any alarm actions to be taken. If this message appears there is a potentially dangerous ground fault condition which should be corrected.The alarm will be triggered any time a current of 2mA or greater is detected from the battery pack to the chassis pin.If the EMS system is being used on a lower voltage system (<50 volts) where the battery pack is grounded to the chassis, this wire should not be installed to disable this feature. EPS does not recommend grounding battery packs in excess of 12 cells in series for safety.When performing work on a high voltage battery pack, the Chassis pin should temporarily be disconnected as it will induce a very small, non-dangerous, current to the chassis which could cause small electrical shocks.18Trouble ShootingA sense board is reporting a temperature above the spec limit and is shutting down the system to protect the batteryCheck for loose connectionsA sense board is reporting a temperature below the spec limit for charging and has shut off charging equipment to protect the battery packA potentially dangerous leakage current to the chassis has occurred. Find the source of this leakage and remove it.For low voltage systems where the battery pack is grounded to the chassis disconnect this pin to eliminate this feature.。
100条充电宝好评
100条充电宝好评1. 这款充电宝质量很好，外观也很漂亮，充电速度也很快。
2. 充电宝的续航能力非常强，可以满足长时间的使用需求，非常实用。
3. 这款充电宝的充电口设计非常人性化，方便快捷。
4. 用这款充电宝充电，不会对手机造成任何损害，非常安全。
5. 充电宝的尺寸很小巧，携带方便，非常适合旅行时使用。
6. 这款充电宝的充电速度很快，可以快速为手机充电。
7. 这款充电宝的充电效率很高，能够快速为手机充满电。
8. 充电宝的外壳材质很好，手感舒适，质量非常可靠。
9. 这款充电宝的续航能力很强，可以满足长时间的使用需求。
10. 这款充电宝的价格非常实惠，性价比很高。
11. 充电宝的使用方法非常简单，方便易学。
12. 这款充电宝的设计非常精美，质感非常好，非常有品质感。
13. 充电宝的颜值非常高，外观设计非常时尚，非常符合年轻人的口味。
14. 这款充电宝的重量很轻，携带方便，非常适合出门旅行时使用。
15. 充电宝的充电速度非常快，可以快速为手机充电，非常实用。
16. 这款充电宝的续航能力非常强，可以满足长时间的使用需求，非常实用。
17. 充电宝的尺寸非常小巧，携带方便，非常适合出门旅行时使用。
18. 这款充电宝的外观设计非常简约大气，非常符合现代人的审美。
19. 充电宝的细节处理非常到位，使用起来非常舒适，非常实用。
20. 这款充电宝的质量非常好，使用起来非常稳定，非常可靠。
21. 充电宝的售后服务非常好，有问题随时可以联系客服解决。
22. 这款充电宝的充电速度比其他充电宝要快很多，非常实用。
23. 充电宝的使用非常方便，可以快速给手机充电，非常实用。
24. 这款充电宝的续航能力非常强，可以满足长时间的使用需求，非常实用。
25. 充电宝的充电效率很高，可以快速为手机充电。
26. 这款充电宝的外观设计非常独特，非常有特色，非常符合个性化需求。
27. 充电宝的质量非常稳定，使用起来非常可靠，非常实用。
28. 这款充电宝的价格非常实惠，性价比很高，非常划算。
充电宝好评评语
充电宝好评评语
1. 这款充电宝充电速度非常快，可以快速为我的手机充电，非常方便！
2. 容量大，可以满足一整天的充电需求，再也不用担心手机没电了！
3. 外观精致，手感舒适，非常适合携带出行使用。
4. 充电宝的质量非常好，使用起来稳定可靠，非常值得购买！
5. 这款充电宝有多个充电口，可以同时给多个设备充电，非常实用！
6. 充电宝的设计非常智能，可以自动识别设备的充电需求，保护设备电池安全。
7. 充电宝的性价比很高，价格实惠，功能齐全，非常满意！
8. 使用起来非常简单，只需要连接上手机就可以开始充电，非常方便！
9. 充电宝的充电效率很高，不用等待太久就可以充满电。
10. 性能稳定，长时间使用不发热，非常安全可靠。
太空舱充电宝详细说明书
太空舱充电宝详细说明书
产品参数：
名称：太空舱充电宝
分类：移动电源
电池类型：圆柱状钢壳
电芯类型：聚合物锂离子电芯
外壳材质：ABS
电源容量：5000毫安
尺寸：80*26*46.5mm
充电功率：5W
使用说明：
1、太空舱充电宝的充电方法和手机一样，用数据线充电，也可以用电脑充电。
2、太空舱充电宝充电的时候，指示灯一个接着一个的闪烁，充满电后常亮不在闪烁。
关闭太空舱充电宝指示灯的方法是连按2下电源键或者长按电源键3到5秒。
3、不用的时候保持百分之50以上的电量，放置在干燥的环境中。
太空舱充电宝不能边充电边给手机充电。
太空舱充电宝注意事项：
1、建议以后充电的同时顺便激活下电池，这样电池充电就没有记忆了。
2、用交流插座充电，把电量充至100%关机，在关机模式下接着充到绿灯亮。
3、开机进入recover模式选择advancsd高级模式，选择wipe Battery ，清除电池痕迹。
4、开机充电至100%这样你的电池就没有记忆了以后充电也快多了。
驭光者·火鸟ELITE太阳能手提式移动电源箱 用户指南说明书
PHOENIX ELITE PORTABLE SOLAR GENERATOREN01 USER GUIDE驭光者·火鸟ELITE太阳能手提式移动电源箱CN18PHOENIX ELITE PORTABLE SOLAR GENERATORUser GuideIMPORTANT SAFETY INSTRUCTIONS PACKAGE CONTENTS FEATURESRECHARGING PHOENIX ELITE LCD SCREENPRODUCT OVERVIEW SPECIFICATIONS TROUBLESHOOTINGFREQUENTLY ASKED QUESTIONS WARRANTYOPERATING PHOENIX ELITE MAINTENANCE 171613131108070604030302Please read the User Guide carefully before recharging or operating your PHOENIX Elite.IMPORTANT SYMBOLSIndicates potentially dangerous conditions that could result in personal injury Indicates conditions or practices that could result in damages to the unit or other equipmentIndicates procedures or functions that are important for proper and safe operation of the unit and/or other equipmentCAUTIONCAUTION CAUTION CAUTIONWARNINGWARNINGWARNINGWARNINGWARNINGWARNINGNOTEDO NOT submerge the unit in water or operate the unit in the rain. Doing so may cause short-circuits, electric shocks, and/or fire.DO NOT place the unit near fire and/or heat the unit. Doing so may cause irreversible damages to the unit and/or battery explosion.DO NOT overload the unit. Please check the specifications of output ports and devices before operation.Please turn off the output ports when no devices are connected to the unit to prevent electric shocks.DO NOT dismantle or modify the unit. Doing so may cause irreversible damages to the unit and void warranty.CAUTIONDO NOT place the unit in high-temperature situations. Doing so may cause unit malfunction or component degradation.CAUTIONDO NOT expose the unit to strong electrostatic fields, strong magnetic fields, and/or radiation.CAUTIONPlease check the unit before each use. Stop using the unit if you notice unusual smells, heating, distortion, or any other abnormalities.DO NOT drop or strike the unit. Doing so may cause circuit failures and cracks in the casing.Please dispose of the product according to the local recycling and environmental regulations.Keep the unit out of the reach of young children.PORTABLE DESIGNFeaturing a portable briefcase design with a sturdy carrying handle, the PHOENIX Elite is the top choice for a weekend trip or an emergency.RENEWABLE ENERGYDesigned for off-grid applications, the PHOENIX Elite combines two highly efficient 10W monocrystalline solar panels for effortless battery replenishment.DIVERSE RECHARGING OPTIONSEngineered with convenience and versatility in mind, the PHOENIX Elite supports recharging from car sockets, AC adapters, USB-C wall chargers, and external solar panels.RELIABLE POWER SOURCEEquipped with a 300Wh rechargeable lithium-ion battery pack and multiple output ports, the PHOENIX Elite is ready to provide long-lasting power for a wide range of mobile devices and small appliances.1 x Renogy PHOENIX Elite Portable Solar Generator1 x AC/DC Adapter1 x Cigarette Lighter Plug to 5.5mm DC Adapter Cable1 x Solar Panel Connectors to 5.5mm DC Adapter Cable1 x USB-C to USB-C Cable1 x User Guide76 12345891011121314CIG Port Output Side DoorDC Output Ports QC USB-A Port USB-A Ports Hinges Input Side Door 15DC Input Port 16USB-C PD Port 17LED Flashlight 18Carrying Handle1914131211109Flashlight On/Off Button Main Power ButtonAC Output Mode On/Off Button DC Output Mode On/Off Button LCD Screen Built-in Solar Panels Latches AC Outlet 876543211516171819InputBatteryGeneralLithium-ion 14.4V20800mAh / 299.5Wh Battery Type Battery Voltage Battery CapacityBuilt-in Solar Panel DC Input Port USB-C PD Port Total9.8V / 2.04A, 20W Max 9-16.8V, 55W Max 16.8-30V, 100W Max5V / 3A, 9V / 3A, 12V / 3A, 15V / 3A, 20V / 3A, 60W Max 180W Max 413 x 308 x 100 mm / 16.3 x 12.1 x 3.9 inch 5.3 kg / 11.7 lb.ABS + PC 3W LED0-45 ℃ / 32-113 ℉-10-60 ℃ / 14-140℉20-90%Dimension Weight Material FlashlightNormal Operating Temperature Storage Temperature Operating / Storage HumidityOutputUSB-A Port (2)QC USB-A Port USB-C PD Port CIG PortDC Output Port (2)AC OutletTotal5V / 2.4A Max5V / 3A, 9V / 2A, 12V / 1.5A, 18W Max5V / 3A, 9V / 3A, 12V / 3A, 15V / 3A, 20V / 3A, 60W Max 13.6V / 9A Max 13.6V / 4.5A Max 110V / 60Hz (US, JP, CA)220V / 50Hz (AU, EU, CN)200W Rated, 300W Surge Pure Sine Wave300W MaxThe LCD Screen will be lit when the PHOENIX Elite is being recharged or turned on to display the recharging and operating status of the PHOENIX Elite. Please refer to the following table to interpret the information displayed on the LCD Screen.The Battery Level is displayed as a ring composed of 10 segments with a percentage in the center. The ring and percentage appear when the PHOENIX Elite is being recharged or is turned on. When recharging the PHOENIX Elite, a lightning bolt will appear above the percentage. The ring will be lit segment by segment with the increasing percentage until the PHOENIX Elite has been fully recharged. As the PHOENIX Elite is used to power other devices, the ring segments will go out one by one with the decreasing percentage. When the battery level is lower than 10%, the last ring segment and the percentage will flash.IconNameDescriptionBattery LevelThe AC Output Mode is displayed as a rectangle with the words ‘AC Output’ inside. The rectangle appears when the AC output mode is activated with the AC Outlet turned on. The rectangle disappears when the AC output mode is deactivated with the AC Outlet turned off.AC Output ModeAC Output The DC Output Mode is displayed as a rectangle with the words ‘DC Output’ inside. The rectangle appears when the DC output mode is activated with the USB-A Ports, QC USB-A Port, USB-C PD Port, CIG Port, and DC Output Ports turned on. The rectangle disappears when the DC output mode is deactivated with the USB-A Ports, QC USB-A Port, USB-C PD Port, CIG Port, and DC Output Ports turned off.DC Output ModeThe Built-in Solar Panel Input is displayed as a sun with 5 bars below it. The sun and bars appear when the PHOENIX Elite detects input power from the Built-in Solar Panel. The number of bars demonstrates the strength of solar irradiance.Built-in Solar Panel InputThe Input Power is displayed as a wattage with the word ‘Input’ above it. The wattage appears when the PHOENIX Elite is being recharged.Input PowerThe Output Power is displayed as a wattage with the word ‘Output’ above it. The wattage appears when the AC output mode or the DC output mode is activated.Output PowerThe Error Code is displayed as a 3-digit code starting with the letter ‘E’. The code appears when the PHOENIX Elite encounters abnormal conditions.Error CodeDC OutputIf the [Error Code] icon appears, the PHOENIX Elite may need special attention. Please refer to the TROUBLESHOOTING section for help.CAUTIONTo maximize the battery life, please ensure that the PHOENIX Elite is fully recharged before operating or storing.To shorten the recharge time, it is highly recommended to disconnect all loads while recharging the PHOENIX Elite.CAUTIONNOTEThe above recharge times are based on conditions when the PHOENIX Elite is recharged at full speed with no loads connected to it.NOTEThe LCD Screen will go out if the input power of the Built-in Solar Panels is lower than 5W and no operations are made within 60 seconds. Press the AC Output Mode On/Off Button or DC Output Mode On/Off Button to relight the LCD Screen.NOTEThe recharge time via the Built-in Solar Panels is highly dependent on solar irradiance and ambient temperature.NOTERecharge TimeRecharge via Built-in Solar Panel: 20 Hours Recharging via Built-in Solar PanelFor optimal recharging performance, it is highly recommended to recharge the PHOENIX Elite using the Built-in Solar Panels on bright sunny days free of scattered clouds.Recharging via External Solar PanelFor optimal recharging performance, it is highly recommended to recharge the PHOENIX Elite using an external solar panel (not included) on bright sunny days free of scattered clouds.Place the external solar panel under direct sunlight. Steer clear of trees or branches that can shade the external solar panel and slow down the recharging process.Place the PHOENIX Elite in an open area. Open the Latches and adjust the angle of the Hinges to expose the Built-in Solar Panels to direct sunlight. Steer clear of trees or branches that can shade the Built-in Solar Panel and slow down the recharging process.The PHOENIX Elite will begin to recharge automatically. The LCD Screen will be lit with the [Battery Level] icon, [Built-in Solar Panel Input] icon, and [Input Power] icon appearing.Recharge via External Solar Panel: 4 HoursRecharge via both Built-in Solar Panel and External Solar Panel: 3.5 Hours Recharge via AC/DC Adapter: 6 Hours Recharge via Car Socket: 6 HoursRecharge via USB-C PD Wall Charger: 6 HoursRecharge via both AC/DC Adapter and USB-C PD Wall Charger: 3 HoursUse the included Solar Panel Connectors to 5.5mm DC Adapter cable to connect the external solar panel to the DC Input Port of the PHOENIX Elite. Place the PHOENIX Elite in the shade to prevent it from overheating.The PHOENIX Elite will begin to recharge automatically. The LCD Screen will be lit with the [Battery Level]icon and [Input Power] icon appearing.Compatible External Solar Panels:Renogy Monocrystalline Solar Panel: 50W, 80W, 100W, 160WRecharging via AC/DC Adapter Plug the PHOENIX Elite into a wall outlet through the DC Input Port using the included AC/DC Adapter.Renogy Polycrystalline Solar Panel: 50W, 100WRenogy ECLIPSE Series Solar Panel: 100WRenogy Monocrystalline Foldable Solar Suitcase w/o Controller: 100WRenogy ECLIPSE Series Foldable Solar Panel w/o Controller: 100W, 200WRenogy Flexible Solar Panel: 50W, 100W, 160W, 175WRenogy E.FLEX Series Portable Solar Panel: 50W, 100W, 120W CAUTION WARNING NOTEElectrical shock can occur if the Solar Panel Connectors to 5.5mm DC Adapter Cable isdamaged or frayed. DO NOT use a damaged or frayed cable to recharge the PHOENIX Elite.Please ensure that the open circuit voltage of the external solar panel does not exceed 30V orfall short of 9V.The recharge time via the external solar panel is highly dependent on solar irradiance andambient temperature.The PHOENIX Elite will begin to recharge automatically. The LCD Screen will be lit with the [Battery Level] icon and [Input Power] icon appearing.Recharging via Car SocketPlug the PHOENIX Elite into a car socket through the DC Input Port using the included Cigarette Lighter Plug to 5.5mm DC Adapter Cable.The PHOENIX Elite will begin to recharge automatically. The LCD Screen will be lit with the [Battery Level] icon and [Input Power] icon appearing.WARNINGElectrical shock can occur if the AC/DC Adapter is damaged. DO NOT use a damaged AC/DC Adapter to recharge the PHOENIX Elite.WARNING DO NOT use a third-party AC/DC adapter to charge the PHOENIX Elite. Doing so may cause the AC/DC adapter to overheat and/or fire.WARNING Electrical shock can occur if the Cigarette Lighter Plug to 5.5mm DC Adapter Cable is damaged or frayed. DO NOT use a damaged or frayed cable to recharge the PHOENIX Elite.CAUTIONPlease disconnect the PHOENIX Elite from the car socket when starting the engine. Electricalsurges from the alternator when starting may damage the PHOENIX EliteRecharging via USB-C PD Wall ChargerFor optimal recharging performance, it is highly recommended to recharge the PHOENIX Elite using a USB-C PD wall charger (not included) with a high power rating.Plug the PHOENIX Elite into a wall outlet through the USB-C PD Port using the USB-C PD wall charger and the included USB-C to USB-C Cable.The PHOENIX Elite will begin to recharge automatically. The LCD Screen will be lit with the [Battery Level] icon and [Input Power] icon appearing.WARNINGElectrical shock can occur if the USB-C PD wall charger is damaged. DO NOT use a damagedUSB-C PD wall charger to recharge the PHOENIX Elite.Recommended USB-C PD Wall Chargers:Apple USB-C Power Adapter: 30W, 61W, 87W, 96WOperation Time Battery Powered Devices:Google USB-C Power Adapter: 45WOperating the PHOENIX Elite at high temperature above 113℉ (45℃) or at low temperatures below 32℉ (0℃) can result in battery performance degradation and service life shortening. Foroptimal battery performance and maximum battery life, it is highly recommended to operate the PHOENIX Elite at room temperatures. CAUTION OPERATING PHOENIX ELITENumber of Full Charges =Device Battery Capacity (Wh)299.5Wh x 70%Powering DevicesPress the Main Power Button to turn on the PHOENIX Elite. The LCD Screen will be lit with the [Battery Level] icon appearing.Compatible DevicesUSB-A Ports / QC USB-A Ports: Smart Watch, Electronic Book, Smart Phone, Tablet, Action Camera, Digital Camera, Bluetooth Speaker, Wireless Headphone, Drone, and other USB-A enabled devicesUSB-C PD Ports: Smart Phone, Tablet, Laptop, Handheld Game Console, DSLR Camera, and other USB-C enabled devicesCIG Port: Portable Refrigerator, Car Vacuum, Car Air Fan, CPAP Machine, and other car powered devices DC Output Ports: LED Strip Light, Modem, Router, Motor, and other DC powered devicesAC Outlet: Laptop, Monitor, TV, Game Console, Inkjet Printer, Portable Projector, Light Bulb, and other AC Powered DevicesTo use the USB-A Ports, QC USB-A Port, USB-C PD Port, CIG Port, or DC Output Ports, first press the DC Output Mode On/Off Button to activate the DC output mode. The [DC Output Mode] icon and [Output Power] icon will appear. Then, connect the device(s) to the port(s) for power. The [Output Power] icon will show the real-time output power. When not using the port(s), long press the DC Output Mode On/Off Button to deactivate the DC output mode. The [DC Output Mode] icon and [Output Power] icon will disappear.To use the AC Outlet, first press the AC Output Mode On/Off Button to activate the AC output mode. The [AC Output Mode] icon and [Output Power] icon will appear. Then, connect the device to the outlet for power. The[Output Power] icon will show the real-time output power. When not using the outlet, long press the AC Output Mode On/Off Button to deactivate the AC output mode. The [AC Output Mode] icon and [Output Power] icon will disappear.When no device is connected to the PHOENIX Elite, press the Main Power Button again to turn it off.DC Powered Devices:Working Hours =Device Power Rating (W )299.5Wh x 95%AC Powered Devices:Working Hours =Device Power Rating (W )299.5Wh x 85%NOTE The above estimation formulas only apply when the PHOENIX Elite has been fully recharged and the device does not draw too much power.NOTEActual number of full charges and working hours may vary due to different powering methods and device operation status.WARNINGThe PHOENIX Elite can provide up to 300W total output power. Allocate the total output powerrationally and follow the specifications of each output port. DO NOT overload the PHOENIXElite. If the total output power should exceed 300W, the AC Outlet will be shut off.Using LED FlashlightPress the Main Power Button to turn on the PHOENIX Elite. The LCD Screen will be lit with the [Battery Level] icon appearing.When not using the LED Flashlight, press the Main Power Button to turn off the PHOENIX Elite.The LED Flashlight has three lighting modes: bright (100% brightness), dim (50% brightness), and SOS. Press the Flashlight On/Off Button to turn on the LED Flashlight, switch lighting modes, and turn off the LED Flashlight. Long press the Flashlight On/Off Button to turn off the LED Flashlight no matter what lighting mode it is on.To prolong the service life of the PHOENIX Elite, keep it away from water, dust, and dirt. DO NOT leave the PHOENIX Elite in harsh environments.Keep the PHOENIX Elite away from corrosives, fire, and heat sources.Keep the PHOENIX Elite recharged when not in use and avoid connecting devices with high power ratings when the battery level is low.If the PHOENIX Elite does not operate normally, please refer to the following table for possible causes and corrective steps.If the following corrective steps do not work, please contact the Renogy technical support team for help. Refer to the last page of the User Guide for contact information.If the PHOENIX Elite is not used frequently, keep its battery level at around 50%. Store the PHOENIX Elite in a clean, dry, and well-ventilated environment with a temperature around 77℉ (25℃) and a humidity no higher than 75%. Recharge the PHOENIX Elite at least once every two months.NOTE The PHOENIX Elite may not be compatible with the devices that require high current impulses despite their conformity with the output ports specifications.NOTEThe PHOENIX Elite may not be able to deliver exactly 299.5Wh of energy when poweringdevices with high power ratings. Battery high temperature protection may be triggered when the PHOENIX Elite is operating at full load. Cool down the PHOENIX Elite before resuming operation. CAUTIONWhen using the AC Outlet, keep 4 inches of space on either side of the PHOENIX Elite to guarantee efficient heat dissipation.CAUTION When the battery level drops to 0%, the PHOENIX Elite will turn off automatically. Please recharge the PHOENIX Elite as soon as possible to avoid permanent damage to the battery.CAUTION When the battery level drops below 10%, use of the AC Outlet will be disabled. If the total outputpower still exceeds 200W, use of the CIG Port and DC Output Ports will be subsequentlydisabled. DO NOT connect devices with high power ratings to the PHOENIX Elite when the battery level is low. CAUTIONDisconnect all the power source(s). Discharge the unit untilthe [Error Code] icon disappears.Error CodePossible Causes Corrective Steps E01Battery Over-voltage Disconnect all the electrical load(s). Recharge the unit untilthe [Error Code] icon disappears.E02Battery Under-voltage Stop using the unit. Contact the Renogy technical supportteam for help.E03Battery Cell Imbalance Stop using the unit. Contact the Renogy technical supportteam for help.E04BMS Communication Failure Disconnect all the power source(s) and electrical load(s).Cool down the unit until the [Error Code] icon disappears.E05Battery High Temperature (Charge)Disconnect all the power source(s) and electrical load(s).Warm up the unit until the [Error Code] icon disappears.E06Battery Low Temperature (Charge)Disconnect the power source. Check the voltage rating ofthe power source. Connect only the power source withcompliant voltage rating to the unit.E07DC Input Port Over-voltage Disconnect the power source. Check the voltage rating ofthe power source. Connect only the power source withcompliant voltage rating to the unit.E08DC Input Port Under-voltage Disconnect the power source. Check the voltage rating ofthe power source. Connect only the power source withcompliant voltage rating to the unit.E09USB-C PD Port Input Over-voltage Disconnect the power source. Check the voltage rating ofthe power source. Connect only the power source withcompliant voltage rating to the unit.E10USB-C PD Port Input Under-voltage Reconnect all the power source(s). If the [Error Code] iconpersists, stop using the unit. Contact the Renogy technicalsupport team for help.E11Charge Over-current Disconnect all power source(s) and electrical load(s). Cooldown the unit until the [Error Code] icon disappears.E12Battery High Temperature (Discharge)Disconnect all power source(s) and electrical load(s). Warmup the unit until the [Error Code] icon disappears.E13Battery Low Temperature (Discharge)Disconnect the electrical load(s). Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E14USB-A Ports Output Over-voltageContact the Renogy technical support team for help.Under-voltage Disconnect the electrical load(s). Remove the shortcircuit(s). Press the DC Output Mode On/Off Button to clearthe [Error Code] icon. Connect only the electrical load(s)with compliant current ratings to the unit.E16USB-A Ports Output Over-current/Short-circuit Disconnect the electrical load(s). Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E17DC Output Ports/CIG Port Output Over-voltage Disconnect the electrical load(s). Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E18DC Output Ports/CIG Port Output Under-voltage Disconnect the electrical load(s). Remove the shortcircuit(s). Press the DC Output Mode On/Off Button to clearthe [Error Code] icon. Connect only the electrical load(s)with compliant current ratings to the unit.E19DC Output Ports/CIG Port Output Over-cur-rent/Short-circuit Disconnect the electrical load. Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E20QC USB-A Port Output Over-voltage Disconnect the electrical load. Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E21QC USB-A Port Output Under-voltage Disconnect the electrical load. Remove the short circuit.Press the DC Output Mode On/Off Button to clear the [ErrorCode] icon. Connect only the electrical load with compliantcurrent ratings to the unit.E22QC USB-A Port Output Over-current/Short-circuit Disconnect the electrical load. Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E23USB-C PD Port Output Over-voltage Disconnect the electrical load. Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E24USB-C PD Port Output Under-voltage Disconnect the electrical load. Remove the short circuit.Press the DC Output Mode On/Off Button to clear the [ErrorCode] icon. Connect only the electrical load with compliantcurrent ratings to the unit.E25USB-C PD Port Output Over-current/Short-circuit Disconnect the electrical load. Remove the short circuit. Letthe unit stand for 10 seconds. Press the AC Output ModeOn/Off Button to clear the [Error Code] icon. Connect onlythe electrical load with compliant power ratings to the unit.E26AC Outlet Output Overload/Short-circuitFirst, make sure that the unit has been turned on by pressing the Main Power Button. If the LCD Screen does not light up after pressing the Main Power Button, please recharge the unit as soon as possible. Then, make sure that the output ports have been turned on by pressing the AC Output Mode On/Off Button and/or DC Output Mode On/Off Button. Finally, make sure that the connected devices conform to the specifications of the output ports. If the [Error Code] icon appears, please see the TROUBLESHOOTING section or contact the Renogy technical support team for help. Refer to the last page of the User Guide for contact information.Contact the Renogy technical support team for help.Over-voltageDisconnect the electrical load. Reactivate the AC output mode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E28AC Outlet OutputUnder-voltage Disconnect all the power source(s) and electrical load(s).Cool down the unit to the room temperature. Press the ACOutput Mode On/Off Button to clear the [Error Code] icon.E29Inverter High Temperature Disconnect all the electrical load(s). Press the AC OutputMode On/Off Button to clear the [Error Code] icon.Reallocate the total output power. E30Total Output Overload1. Why doesn't the PHOENIX Elite power external devices?No, the battery in PHOENIX Elite is not replaceable. Do not try to dismantle the PHOENIX Elite and replace the battery by yourself. Doing so may cause irreversible damages to the unit and/or battery explosion.2. Can I replace the battery in the PHOENIX Elite?No, the PHOENIX Elite cannot be chained together or with other rechargeable AC power supplies. If you are looking for a rechargeable AC power supply with a large capacity,, please visit our website or contact us for more options. Refer to the last page of the User Guide for contact information.3. Is the PHOENIX Elite chainable?No, the PHOENIX Elite is not waterproof. Please keep the unit away from moisture. Do not submerge the unit into water or operate the unit in the rain. Doing so may cause short-circuit, electric shocks, and fire.4. Is the PHOENIX Elite waterproof?The battery capacity of the PHOENIX Elite is rated at 0.2C. When the PHOENIX Elite is powering devices with high power ratings, the internal resistance of the battery will turn more energy into heat and lower the energy conversion efficiency. As a result, you may not get exactly 299.5Wh of energy.5. Why doesn't the PHOENIX Elite last as long as I expect?RENOGY products are covered by a 12-month limited warranty from the original purchase date. If any problems occur, please contact us for assistance. Refer to the last page of the User Guide for contact informa-tion.We only provide after-sales services for products that are sold by RENOGY or retailers and distributors authorized by RENOGY. If you have purchased your unit from other channels, please contact your seller for more information about return and warranty.Please register your purchase(s) directly at /support/tickets/new or your region’s corresponding website so that we can stay in touch and contact you in the unlikely event that a safety recall is required.驭光者·火鸟ELITE太阳能手提式移动电源箱用户指南安全操作准则产品配件产品特性为火鸟Elite充电LCD 屏幕产品概况产品参数故障排除常见问题售后质保使用火鸟Elite 维护343331312926252422212120请在为本机充电或使用本机前仔细阅读用户指南。
移动电源产品介绍
移动电源产品介绍
移动电源，也被称为便携式充电宝，是一种能够将电能存储起来，并在需要时以电能输出给电子设备进行充电的便携式电源产品。
随着移动设备的普及，如智能手机、平板电脑等，人们对电源的需求也越来越大，而移动电源因其便携性和实用性成为了人们在出门携带的必备之一、下面将为大家介绍几款常见的移动电源产品。
1.品牌：小米
2. 品牌：Anker
3. 品牌：RAVPower
4. 品牌：Yoobao
总结起来，移动电源是一种便携式电源产品，用于为手机、平板电脑等移动设备充电。
各品牌的移动电源产品种类繁多，容量和功能多样，消费者可以根据自己的需求选择适合的产品。
无论是小米、Anker、RAVPower还是Yoobao，这些品牌的移动电源产品都具备高品质、高效率和多重保护功能，能够满足消费者的充电需求，带来更加便捷和舒适的使用体验。
小米移动电源3plm07mz说明书
小米移动电源3plm07mz说明书
小米移动电源3PLM07MZ说明书
重要提示：
1. 本产品仅可用于充电手机、平板电脑、数码相机和其他兼容的设备，禁止用作其他用途。
2. 避免将电源放置在极端温度、潮湿和高压环境下。
3. 请勿将电源与水或其他液体接触。
4. 请在遇到异常情况时立即停止使用电源，并咨询专业人士。
5. 仅使用原装配件和电缆，以确保最佳使用效果。
6. 在使用和携带电源时要小心，避免碰撞和摔落。
产品特点：
1. 大容量：电源内置高效锂离子电池，容量达到（请依具体型号而定）mAh，为您的设备提供持久稳定的电力支持。
2. 多重保护：内部芯片提供过压、过流、短路和过温保护功能，充电
更安全可靠。
3. 快速充电：采用快速充电技术，能够为您的设备提供更快速的充电
速度。
4. 多接口：电源具备多个USB接口，允许同时为多个设备提供充电
（具体根据型号而定）。
5. 可视显示：设备配备显示屏，实时显示电量和充电状态。
使用方法：
1. 将电源与您的设备通过USB连接线连接起来。
2. 按下电源按钮，即可开始为设备充电。
3. 使用结束后，请按住电源按钮，确保电源关闭。
注意事项：
1. 请勿将电源长时间放置未使用，以免电量逐渐减少。
2. 请勿将电源置于高温或阳光直射的环境中。
3. 请勿在充电时使用设备。
4. 请勿将电源与金属物品一起携带，以防短路。
5. 请勿进行拆卸或修理，以免损坏电源。
感谢您选购小米移动电源3PLM07MZ，如需更多帮助，请咨询小米客服中心。
移动电源包装说明(1)
4.放完一层产品 （18pcs)后,再放一张 纸卡
外箱包装
5.第二层的装法和第一 层一样。一箱内放三层 产品，最上面一层只需 放14pcs，一箱放50pcs
6.在最上面空位处填 充气泡袋
外箱包装
7.用气泡纸将侧边空 隙填满
外箱包装 8.在最上放叠放两侧 汽泡纸，确保压实且 不会涨箱
9.在气泡纸上在叠放 纸张硬纸板
移动电源包装说明
内盒
内盒里面包含：小白 盒，移动电源，USB 充电线，说明书
分别将移动电源，USB充 电线，说明书装进小白盒 内
外箱包装 1.外箱选择3号箱， 尺寸27*22*20cm,一 箱放50pcs
2.在外箱内部先放一 张平板纸卡
外箱包装
3.将装好移动电源的小白 盒平方进外箱内，一层 放18pcs；然后将侧边空 隙用.在外箱一侧贴防火标 签，防火标签上会有天目 的联系电话。
科智KZ-730正品手机移动电源20000m毫安通用平板智能充电宝器电池
常见问题解答：1.给移动电源充电多久才能充满呢？>>这款移动电源大概充10小时左右就可以充满了哦，第一次需充满24小时。
2.请问移动电源怎么给我的手机充电?>>亲，用充电线连接到移动电源的1A接口或者2.1A接口就可以了哦。
（是不是很简单，对啦，与你平时给手机充电是一模一样的。
）给ipad或三星平板电脑充电必须选择有5V/2A输出的移动电源，使用2A以下输出的移动电源会导致充不饱和或充电后使用时间短的问题，甚至出现不充电的现象。
3.爱国者E100移动电源能给手机充几次电？>>经过掌柜亲自实测，可以给苹果IPHONE4充电大概5次左右，IPAD能充80%.(具体视个人使用情况哈）。
4.什么叫充电器，如何给移动电源本身充电？>>亲充电器是给移动电源充电的，此宝贝本身是没有配送充电器哦.亲可以用您手机的充电器连接上去直接充电或者在这里购买一个哦，另外也可以插到电脑的USB口也可以直接充电的哦。
5.此宝贝有配送苹果IPHONE5/IPAD4的接口吗？没有配送要怎么充电？>>亲这款暂时还没有配送IPHONE5/IPAD4的接口的哦，亲们可以用自己的数据线也是一样的哈。
6.请问什么时间发货？几天能到>>亲在17：00点之前拍下付款的订单正常当天发货的哈，如果有特殊情况我们都是给您旺旺留言的哦。
因为移动电源不能走航空，只能陆运，发顺丰速递也是陆运，和其他快递速度一样的，3-5天送到，特殊情况除外。
7.如何保修？保修是多久？>>亲,爱国者的产品是全国联保一年，如果有问题可以随时联系爱国者本地售后机构或者直接联系我们的哈，我们会第一时间帮您处理哈，亲您放心哈。
8.移动电源怎么充不进去电、充不满电，怎么办，是不是移动电源有问题？>>E100是10000毫安的大容量移动电源，充电时间本来就比较长。
如果出现充不进去点或者充不满电，您换一个充电线或者充电插头试试，如果还是这中情况，可能就是移动电源质量问题，您可以联系我们的售后解决问题。
充电宝好评评语
充电宝好评评语
- 这个充电宝非常轻巧便携，适合随身携带，解决了我的手机电量不足的问题。
- 充电速度很快，只需短短几分钟就能给手机充满电，非常方便。
- 容量很大，一次充电可以满足我一整天的使用，再也不用担心手机没电了。
- 充电宝的外观设计很时尚，质感很好，给人一种高端感。
- 使用起来非常简单，只需连接线缆即可开始充电，不需要复杂的操作。
- 充电宝的电量显示功能很实用，可以清晰地知道剩余电量，避免了突然没电的尴尬。
- 保护措施很完善，使用起来非常安全，不会对手机造成任何损害。
- 充电宝的续航能力很强，可以多次给手机充电，非常耐用可靠。
- 充电宝的充电速度与效果都非常稳定，不会出现充电过慢或者充电不充满的情况。
- 充电宝的价格相对来说比较合理，性价比很高，非常值得购买。
苹果4s充电宝 品牌移动电源 品能充电宝
苹果4s充电宝品牌移动电源品能充电宝随着个人移动终端设备增量惊人，特别是智能手机的凶猛攻势和PAD风潮的大肆席卷，催生出安全移动电源的产业契机。
1、Moka慕卡：唯一安全移动电源品牌，新一代安全移动电源创始者。
各大电商平台销量第一。
2、MiLi：Hali-power的自有品牌，以其极具创意的设计和优异的品质保障，以及创新的电池和充电器解决方案为今天的移动设备带来了新的发展。
3、三洋：三洋集团，移动电源是之一的产品。
4、飞毛腿：公司成立于1997年，是一家拥有独立强大品牌销售网络、最具先进制造规模，为移动数码产品提供全面电池解决方法的国内电池行业最具品牌价值企业。
5、太空步：Monwalk太空步，全球著名移动消费电子品牌，在安全移动电源领域颇有影响力。
太空步移动电源推出金盾五重保护技术、智能微温持流供电技术、智能升压转换供电技术、智能自适应技术、智能快充专利技术、智能自动关机技术等智能充电新技术，使太空步移动电源成为智能化、安全化的领导性产品。
6、爱国者：爱国者AIGO北京华旗资讯科技发展有限公司，是一家1993年创立于北京中关村的高新技术企业。
7、劲量：是著名的电池和手电筒品牌，总部位于美国密苏里州Town and Country，同时生产移动电源8、羽博：PDA电池到手机电池、座充、商务充、双充、车充、数码电池、皮套、清水套。
9、立派：立派商标所有权均属于深圳宝商科技有限公司10、品胜：广东品胜电子股份有限公司Moka(慕卡)安全移动电源【商务型：i6】20000毫安大容量，首款不发烫、无辐射、京东天猫有售移动电源移动电源一种集供电和充电功能于一体的便携式充电器，可以给手机等数码设备随时随地充电或待机供电。
一般由锂电芯或者干电池作为储电单元。
区别于产品内部配置的电池，也叫外挂电池。
一般配备多种电源转接头，通常具有大容量、多用途、体积小、寿命长和安全可靠等特点，是可随时随地为手机、数码相机、MP3 、MP4 、PDA 、掌上电脑、掌上游戏机等多种数码产品供电或待机充电的功能产品。
充电宝,说明书
篇一：充电宝综合说明书概述：超威便携式移动电源是一种集供电和充电功能于一体的便携式充电装置的电能存储器，由高能量集合物锂离子电芯作为储电载体。
具有大容量、多用途、体积小、寿命长和安全可靠等特点。
使用说明：适用于mn0510mh、mn0510ma/8g、mn0505mb、mn0505md、mn0505mf、 mn0502mc型号：照明功能长按按键3s以上，led照明开启，再轻按按钮则关闭led照明（mn0502mc除外）；对数码产品充电：将充电线接入usb 口，轻按按键，即可给dc5v输入的电子产品充电，充电过程中电量指示灯长量，提示剩余电量。
（mn0502mc：无需按按键，充电过程中无电量显示）；对移动电源充电：选择适配器（输出直流电压5v）或电脑usb口，将充电头插入移动电源充电口，即可给移动电源进行充电；电量查询：短按按键，即可查询移动电源剩余电量（mn0502mc不可查询剩余电量，在缺电的情况下会亮红灯，表示需要充电）；休眠状态：在无充、放电（既待机状态），无照明时，5分钟后自动进入休眠状态；适用于mn1910me 型号：对移动电源充电：请用输出直流电压15~19v，电流≧2a的适配器对移动电源进行充电，充电时lcd显示充电状态（电量格成流水状跳动）和输出口输出电压。
当适配器电压不符合要求时，电量格整体闪动。
开机和关机：在关机状态下，短按按键开机，开机显示当前电池电量、输出口输出电压、usb符号。
关机：输出口未接入负载并不在输出锁定状态时，可以短按按键关机；输出口未接入负载并不在输出锁定状态时，电源在无负载时10分钟后自动关机；输出口接入负载后，须长按按键关机；显示锁定符号时电源不会自动关闭，将保持长期开机状态。
对数码产品进行充电：对数码产品充电时，usb口可以对5v的数码产品如手机，ipad等进行充电，usb口输出不随手动调整电压而变动，恒定输出5v；dc输出口输出电压可以在5v/7.4v/9v/12v/16v/19v之间循环调整，在未接入负载时，长按按键即可调整电压，持续长按，电压连续调整。
移动电源哪个牌子好_移动电源十大品牌排行榜
移动电源哪个牌子好_移动电源十大品牌排行榜现在玩手机得时间越来越多，电量也越来越不管用，就有了移动电源的产生，接下来店铺向大家介绍一下移动电源十大品牌排行榜。
移动电源十大品牌排行榜移动电源品牌排名1：沃品"Wopow沃品"品牌，由深圳市沃品科技有限公司全权运营。
WOPOW沃品是中国最具创新精神和创新能力的数码智能电源与外设品牌，是“中国创造”的先驱和领先者。
产品通过IS09001、ISO14001、3C、CE、FCC、TLC、UL、GS等一系列国际、国内认证。
20%研发经费投入，30多项外观专利。
成为移动数码产品国内电池行业最具品牌价值企业。
移动电源品牌排名2：品胜羽博注重品质铸造未来，秉承了专注、专心、专研，从事PDA、手机、数码系列电池研发，在高容量商务电池独树一帜，拥有雄厚的技术力量，齐全的生产检测设备，产品精工制造，从原料的采购、产品的生产、检测、销售及售后服务各个环节，都严格实行全面品质监控和保障。
移动电源品牌排名3：羽博羽博注重品质铸造未来，秉承了专注、专心、专研，从事PDA、手机、数码系列电池研发，在高容量商务电池独树一帜，拥有雄厚的技术力量，齐全的生产检测设备，产品精工制造，从原料的采购、产品的生产、检测、销售及售后服务各个环节，都严格实行全面品质监控和保障。
移动电源品牌排名4：罗马仕用三个偏执来概括：偏执于只做超智能电源产品，偏执于充电技术的创新，偏执于网络直销!专注于电商领域的黑马。
移动电源品牌排名5：电小二自2007年开始，广东电小二科技有限公司专为APPLE设备研发充电宝产品。
广东电小二科技有限公司始终坚持“安全第一，用户至上”的经营理念，立志将电小二充电宝打造成为iPhone充电宝第一品牌。
移动电源品牌排名6：飞毛腿电池行业领头企业的飞毛腿电池有限公司，也在2005年便率先进入移动电源市场，经过多年的研发与生产。
移动电源品牌排名7：aigo(爱国者)华旗资讯旗下的子品牌爱国者的英文商标, 由著名IT创始人冯军于1993年创立，2010年8月更名为爱国者数码科技有限公司. 成为令国人骄傲的国际性企业"是华旗资讯数码科技有限公司的奋斗目标。
罗马仕30000说明书
罗马仕30000说明书
产品特性：过压保护，短路保护，过充保护，过放保护，过流保护,温度保护，Reset保护。
产品类型：通用分体式。
电池类型：锂电池。
电芯容量：30000mA。
适用设备：普通移动电源。
适用产品：支持市面上主流手机，平板电脑，任天堂Switch等设备充电，且不伤机。
产品电压输入：5V，9V 输出：5V，9V，12V。
产品电流输入：2A(MicroUSB端口，Type-C接口)，2.1A(Lightning) 输出：3A，2A，1.5A，2.1A。
安全功能：过充保护，过流保护，Reset保护，过放保护，过压保护，温度保护，过功率保护，防反保护，短路保护，电磁场保护。
充电时间：11-12小时(使用18W电源适配器)。
输入接口：安卓Micro USB接口苹果Lightning接口安卓Type-C 双向接口。
输出接口：双USB输出Type-C快充输出口。
便携式充电宝商品说明书随身携带永不断电
便携式充电宝商品说明书随身携带永不断电便携式充电宝商品说明书随身携带，永不断电尊敬的用户，感谢您选择使用我们的便携式充电宝产品。
本说明书将为您详细介绍该产品的特点、操作方法以及注意事项。
请在使用前仔细阅读本说明书并妥善保管，以确保您能够充分了解并正确使用我们的产品。
产品特点：1.小巧便携：本充电宝采用轻巧的设计，体积小巧，便于随身携带，方便您随时随地进行充电。
2.高效输出：充电宝采用先进的技术，能够提供高效稳定的输出电流，快速充电您的各类电子设备。
3.多功能接口：产品配备多种充电接口，包括USB、Type-C等，可适应大部分手机、平板电脑和其他设备的充电需求。
4.智能保护：充电宝内置多重保护机制，包括过充、过放、短路等保护功能，为您的设备提供安全可靠的充电保护。
使用方法：1.首次使用前，请确保充电宝已经充满电。
您可以通过连接充电器或电脑的USB接口对充电宝进行充电，LED指示灯将显示充电状态。
2.将充电宝与您的设备连接，使用合适的充电线缆将充电宝的接口与设备的充电接口相连接。
在连接成功后，LED指示灯将显示正在充电的状态。
3.在充电过程中，LED指示灯将显示充电进度。
当LED指示灯全部点亮表示充电宝已充满电，您可以断开充电连接。
4.为了避免损坏设备或充电宝本身，请注意不要将充电宝长时间暴露在高温、潮湿的环境中，并避免与水或其他液体接触。
5.当您不再使用充电宝时，请确保将其关机，并存放在干燥通风的地方。
注意事项：1.请勿将充电宝拆解或进行任何自行维修的行为，以免造成危险。
2.请不要将充电宝置于儿童易取得的位置，以免发生意外。
3.请使用配套的充电线缆，以确保安全稳定的充电效果。
4.请勿将充电宝投入火中或进行任何不当操作，以防止发生火灾或其他意外危险。
5.尽量避免超过充电宝的额定功率范围进行充电，以确保充电宝的正常使用寿命。
我们始终致力于为用户提供高品质、可靠性和安全性的产品。
如您对本产品有任何疑问或建议，请随时联系我们的客户服务中心，我们将竭诚为您提供帮助。
充电宝的卖点文案
充电宝的卖点文案
嘿，朋友！你是不是经常出门在外，手机电量却像个调皮的孩子，
说跑就跑？这时候，你就急需一个靠谱的充电宝来救场啦！
比如说，上次我和朋友一起去爬山，一路上拍拍美景，聊聊趣事，
正开心着呢，我的手机突然就没电关机了！那感觉，就像在黑暗中迷
失了方向，心里那个着急呀！要是有个给力的充电宝，哪会这么狼狈？
咱这款充电宝，那可真是个小能手！它的容量超大，就像一个能量
小仓库，能给你的手机充好几次电呢！想象一下，你在旅途中，不管
是坐火车、坐飞机，还是在偏远的地方，都不用担心手机没电没法跟
家人朋友联系，这多安心呐！
它的充电速度也超快，简直就是闪电侠附体！不像有些充电宝，充
半天电也不见手机电量涨多少，急死人！
而且，它的个头不大，轻巧便携，放在包里一点不占地方，就跟装
了个小饼干似的。
不像有的充电宝，又大又重，带着简直是个累赘！
还有哦，它的外观设计也超时尚，简约又大方。
拿在手里，感觉自
己都变得更有范儿了！
这么棒的充电宝，难道你不心动吗？反正我是爱惨它啦！我觉得，
这简直就是现代人出门必备的神器，谁能拒绝拥有它呢？。
罗马仕充电宝操作方法
罗马仕充电宝操作方法
1. 插入充电宝电源线：将充电宝的电源线插入充电宝的输入接口，另一端插入电源插座。
2. 充电宝充电：充电宝插上电源后，一般会自动进入充电状态，此时可以通过充电宝上的指示灯来了解充电的进程。
充电时间根据电源容量的不同而有所差异，一般需要数小时至数十小时。
3. 使用充电宝充电设备：充电宝充满电后，可以将需要充电的设备用数据线连接到充电宝的输出接口上，并确保充电宝与设备连接稳固。
4. 启动充电宝：通过按下充电宝上的启动按钮或触摸屏来开启充电宝，开始给设备进行充电。
5. 关闭充电宝：当设备充电完成后，可以手动关闭充电宝，一般有按下充电宝上的关闭按钮或长按触摸屏来完成。
对于不同型号的罗马仕充电宝，可能会有略微的差异，可以参考使用说明书来了解具体的操作方法。
绿联小鸟充电宝使用说明
绿联小鸟充电宝使用说明引言：随着移动设备的普及，人们对于充电宝的需求也越来越大。
绿联小鸟充电宝作为一款便携式充电设备，备受用户喜爱。
本文将为大家详细介绍绿联小鸟充电宝的使用方法，帮助大家更好地享受移动充电的便利。
一、充电宝的外观和规格绿联小鸟充电宝采用了小巧便携的设计，外壳材质为耐磨的ABS塑料，手感舒适。
尺寸为100mm*60mm*25mm，重量约为200克，非常适合携带。
二、充电宝的充电和放电1. 充电：使用附带的Micro USB数据线，将充电宝与电源连接。
当充电宝电量低于20%时，LED指示灯会亮起，并显示当前电量的百分比。
待LED指示灯全部亮起时，即表示充电宝已充满电。
2. 放电：将充电宝与需要充电的设备通过USB数据线连接。
充电宝会自动识别设备的充电需求，并根据设备的充电状态进行智能充放电控制。
当设备充满电后，充电宝会自动停止输出，以保护设备电池的寿命。
三、充电宝的保护功能1. 过充保护：当充电宝充满电后，会自动停止充电，避免过充对设备和充电宝本身造成损害。
2. 过放保护：当充电宝电量过低时，会自动进入睡眠状态，防止电池过放导致无法正常使用。
3. 过流保护：当充电宝输出电流异常时，会立即停止输出，保护设备免受损害。
4. 短路保护：当充电宝输出端口短路时，会自动切断输出，避免损坏充电宝和设备。
四、充电宝的常见问题解答1. 为什么充电宝充电速度很慢？充电宝的充电速度受到电源输出电流和充电宝本身的充电电流限制。
建议使用2A及以上的电源进行充电，可以提高充电速度。
2. 充电宝能否同时给多个设备充电？可以，绿联小鸟充电宝的输出端口支持同时给多个设备充电，满足用户多设备充电的需求。
3. 充电宝可以充电多少次手机？充电宝的续航能力取决于电池容量和设备的充电需求。
一般情况下，绿联小鸟充电宝可以为普通手机充电2-3次。
五、使用注意事项1. 请使用原装的充电线进行充电，避免使用劣质充电线导致充电不稳定。