HASCO模具配件中英文对照表
常用模具零件中英文对照表
常用模具零件中英文对照表2005-12-19 14:51:17中国注塑网一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机〔尼龙拉勾〕：nylon latch lock斜顶：lifter模胚〔架〕：mold base上内模：cavity insert下内模：core insert行位〔滑块〕：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞:pipeplug锁模块：lockplate斜顶：anglefrompin斜顶杆：angleejectorrod尼龙拉勾：partinglocks活动臂：leverarm复位键、提前回杆：earlyreturnbar气阀：valves斜导边：anglepin术语：terms承压平面平衡：partingsurfacesupportbalance模排气：partinglineventing回针碰料位：returnpinandcavityinterference模总高超出啤机规格：moldbaseshuthight顶针碰运水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate.不准用镶件：Donotuse(core/cavity)insert用铍铜做镶件：useberylliumcopperinsert初步〔正式〕模图设计：preliinary(final)molddesign反呵：reversecore弹弓压缩量：springcompressedlength稳定性好：goodstability,stable强度不够：insufficientrigidity均匀冷却：evencooling扣模：sticking热膨胀：theroexpansion公差：tolorance铜公(电极〕：copperelectrode塑件模具相关英文词汇出处：FanE『翻译中国』(转载) FanE『翻译中国』2005-12-16 20:41:59compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型、射出成型用模具two plate两极式〔模具〕well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针零件英语punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块 air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块14. electrical discharge machining (EDM) 电火花加工15. electrical insulating property 电绝缘性能16. electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床17. electrochemical machine (ECM) 电解加工机床，电化学加工机床18. electrochemical machining (ECM) 电解加工，电化学加工19. electro-discharge cutting 电火花加工，电火花切割20. electro-discharge cutting machine 电火花切割机21. electro-discharge machine tool 电火花加工机床22. Electro-discharge Machine 电火花加工机床23. electro-discharge machining 电火花加工24. electro-discharge machining process 电火花加工工艺，电火花加工工序25. epoxy resin 环氧树脂9. guide bushing 导套10. guide pillar 导柱，导杆，导柱11. guide pin 导向销，导杆12. guide pin cover 导柱盖13. guide plate 导料板，导板14. guide plate blanking die 导板式冲裁模，导板式落料模15. guide post 导柱，导柱16. guide stock plate 挡料板4. injection mold 注射模，注塑模5. injection molding 注射成型，注塑成型6. injection-molding machine 注塑机，注射机，注塑成形机7. injection plunger 注射柱塞8. in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆9. inner ram 内滑块10. inserting molding 嵌件成形11. integrated manufacturing 集成制造12. internal stress 内应力13. intermediate platen 中间板，隔板塑料成型模具的主要设计要素脱模距stripper distance脱模斜度draft投影面积projected area最大开距maximum daylight;open daylight闭合高度mould-shut height抽芯距core-pulling distance抽芯力core-pulling force脱模力ejector force开模力mould opening force模内压力internal mould pressure;cavity pressure成型压力moulding pressure背压环back-up ring1 bar = 14.5psi高压接头bite type fitting液压马达hydraulic motor冷却水流量计waterflow regulator打磨器材abrasive material打磨砂轮grinding wheels切割砂轮cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具piping tools高压力软管high pressure hose风管,水软管air .water hose高压油表pressure gauge压力油喉hydraulic hoses光塑检测photoelastic testing吹塑模plastic blow mould注塑模plastic injection mould冲扎复合模blank & form compound die精密冲模precision blanking die熔料流动率MFR=melt flow rate熔料流动指数MET=melt flow index推板导柱guide pin for ejector plater座板clamping plate垫块space block(plate)推板ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形distortion弯曲warp拖花drag marks火花纹EDM marks困气venting烧黑burns外表缩水shrinkage料位过薄/砸穿thin wall stock走水不平行uneven fill pattern夹水纹/流纹witness line;mismatch;stress marks 走水纹knit lines走水不齐short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴tensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (别离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的局部,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,去除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 工程编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱. BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力side pulling-core forceconvert.transfer 转图guide pin 边针Tee slot cutter T形SLOT CUTTERzigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用)air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制平安吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45度,退刀口0度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离)clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有上下ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 平安带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R尺寸sprue bushing-keyed 唧嘴有管钉English Chineseprogram name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth 正侧双用镶钻石钢锣刀end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层。
常用模具零件中英文对照表
常用模具零件中英文对照表2005-12-19 14:51:17中国注塑网一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catchFor personal use only in study and research; not for commercial use喉塞:pipeplug锁模块：lockplate斜顶：anglefrompinFor personal use only in study and research; not for commercial use斜顶杆：angleejectorrod尼龙拉勾：partinglocks活动臂：leverarm复位键、提前回杆：earlyreturnbar气阀：valves斜导边：anglepin术语：terms承压平面平衡：partingsurfacesupportbalance模排气：partinglineventing回针碰料位：returnpinandcavityinterference模总高超出啤机规格：moldbaseshuthight顶针碰运水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate.不准用镶件：Donotuse(core/cavity)insert用铍铜做镶件：useberylliumcopperinsert初步（正式）模图设计：preliinary(final)molddesign反呵：reversecore弹弓压缩量：springcompressedlength稳定性好：goodstability,stable强度不够：insufficientrigidity均匀冷却：evencooling扣模：sticking热膨胀：theroexpansion公差：tolorance铜公(电极）：copperelectrode塑件模具相关英文词汇出处：FanE『翻译中国』作者：(转载) FanE『翻译中国』2005-12-16 20:41:59compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型、射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat 浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spearhead刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line 熔合痕eject pin顶出针零件英语punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块14. electrical discharge machining (EDM) 电火花加工15. electrical insulating property 电绝缘性能16. electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床17. electrochemical machine (ECM) 电解加工机床，电化学加工机床18. electrochemical machining (ECM) 电解加工，电化学加工19. electro-discharge cutting 电火花加工，电火花切割20. electro-discharge cutting machine 电火花切割机21. electro-discharge machine tool 电火花加工机床22. Electro-discharge Machine 电火花加工机床23. electro-discharge machining 电火花加工24. electro-discharge machining process 电火花加工工艺，电火花加工工序25. epoxy resin 环氧树脂9. guide bushing 导套10. guide pillar 导柱，导杆，导柱11. guide pin 导向销，导杆12. guide pin cover 导柱盖13. guide plate 导料板，导板14. guide plate blanking die 导板式冲裁模，导板式落料模15. guide post 导柱，导柱16. guide stock plate 挡料板4. injection mold 注射模，注塑模5. injection molding 注射成型，注塑成型6. injection-molding machine 注塑机，注射机，注塑成形机7. injection plunger 注射柱塞8. in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆9. inner ram 内滑块10. inserting molding 嵌件成形11. integrated manufacturing 集成制造12. internal stress 内应力13. intermediate platen 中间板，隔板塑料成型模具的主要设计要素脱模距stripper distance脱模斜度draft投影面积projected area最大开距maximum daylight;open daylight闭合高度mould-shut height抽芯距core-pulling distance抽芯力core-pulling force脱模力ejector force开模力mould opening force模内压力internal mould pressure;cavity pressure成型压力moulding pressure背压环back-up ring1 bar = 14.5psi高压接头bite type fitting液压马达hydraulic motor冷却水流量计waterflow regulator打磨器材abrasive material打磨砂轮grinding wheels切割砂轮cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps小五金工具piping tools高压力软管high pressure hose风管,水软管air .water hose高压油表pressure gauge压力油喉hydraulic hoses光塑检测photoelastic testing吹塑模plastic blow mould注塑模plastic injection mould冲扎复合模blank & form compound die精密冲模precision blanking die熔料流动率MFR=melt flow rate熔料流动指数MET=melt flow index推板导柱guide pin for ejector plater座板clamping plate垫块space block(plate)推板ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形distortion弯曲warp拖花drag marks火花纹EDM marks困气venting烧黑burns表面缩水shrinkage料位过薄/砸穿thin wall stock走水不平行uneven fill pattern夹水纹/流纹witness line;mismatch;stress marks 走水纹knit lines走水不齐short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴tensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (分离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的部分,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,清除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 项目编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱. BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力side pulling-core forceconvert.transfer 转图guide pin 边针Tee slot cutter T形SLOT CUTTERzigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用) air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制安全吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45度,退刀口0度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离)clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有高低ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 安全带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R尺寸sprue bushing-keyed 唧嘴有管钉English Chineseprogram name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth 正侧双用镶钻石钢锣刀end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层仅供个人用于学习、研究；不得用于商业用途。
hasco标准件的中英文对照
HASCOZ标准件系列Z00 导柱Guide pillarZ01 导柱Guide pillarZ011 导柱Guide pillarZ012 导柱Guide pillarZ013 导柱Guide pillarZ014 导柱Guide pillarZ0141 导柱连接端End pieceZ0142 导柱连接端End pieceZ015 导柱Guide pillarZ0151 导柱连接端(Z015/…专用)Pillar adapterZ0152 导柱连接端Pillar adapterZ02 顶杆Ejector rodZ022 导管Guide sleeveZ03 导柱Guide pillarZ05 圆锥形管精定位Locating unit, round Z055 圆形垫片SpacerZ056 圆形垫件SpacerZ06 平锥形导块Locating unitZ07 长方形导块Square guide barZ08 直身方形管位导块Pre-centering unitZ081 方形垫片Spacer discZ091 方形定位锁块(公)Square interlockZ092 方形定位锁块(母)Square interlockZ093 方形定位锁块(母)Square interlockZ10 导套Guide bushZ10W 自润滑导套Guide bushZ11 导套Guide bushZ11W 自润滑导套Guide bushZ12 滚珠导套Ball guide bushZ13W 自润滑导套Self lubric.Guide bush Z15W 自润滑垫片Self lubric. Flat stock Z16W 自润滑垫片Self lubric. Guide rail Z17 长方形导块(Z07/...专用)Guide retainerZ20 定板导套Centering sleeveZ25 定位销Dowel pinZ26 定位销Dowel pinZ28 六角螺母Hexagon nutZ281 六角螺母Hexagon nutZ282 六角螺母Hexagon nutZ285 螺母Nut for T-slotsZ286 螺母Nut for T-slotsZ30 胚头内六角螺丝Socket head cap screwZ31 胚头内六角螺丝Socket head cap screwZ32 薄胚头内六角螺丝Socket head cap screwZ33 薄胚头内六角螺丝Countersunk screwZ34 内六角螺丝Hexagon socket set screw Z35 内六角螺丝Hexagon socket set screw Z351 内六角螺丝Hexagon socket set screw Z352 螺丝杆Locking screwZ36 弹簧滚珠螺丝Spring plungerZ361 弹簧滚珠螺丝Spring plungerZ37 弹簧滚珠螺丝Spring plungerZ370 弹簧定位螺丝Spring plungerZ371 弹簧滚珠螺丝Spring plungerZ372 弹簧定位螺丝Spring plungerZ3721 弹簧定位螺丝Spring plungerZ373 弹簧定位镶件Spring plungerZ374 弹簧滚珠镶件Spring plungerZ375 弹簧滚珠镶件Spring plungerZ38 限位螺丝Shoulder screwZ381 螺丝Slotted shoulder screwZ39 螺丝Slotted shoulder screwZ40 顶针(全硬)Ejector pinZ41 顶针(表层硬)Ejector pinZ42 顶头顶针(全硬)Ejector pinZ43 顶头顶针(表层硬)Ejector pinZ44 有托顶针(表层硬)Shouldered ejector pinZ441 有托顶针(全硬)Shouldered ejector pinZ442/.../S 有托顶针(定制件)Ejector pinZ45 司筒(表层硬)Ejector sleeveZ451 司筒(全硬)Ejector sleeveZ4501 司筒(全硬)Ejector sleeveZ452/…/S 司筒(定制件)Ejector sleeveZ453/…/S 司筒(定制件)Ejector sleeveZ454/…/S 司筒(定制件)Ejector sleeveZ455/…/S 司筒(定制件)Ejector sleeveZ456 顶针耐磨镶件Wear sleeveZ456/…/S顶针耐磨镶件(定制件)Wear sleeveZ46 扁顶针(表层硬)Flat ejector pinZ461 特殊扁顶针Special flat ejectorZ462 特殊扁顶针镶件(Z461/…专用)GuideZ465 扁顶针(全硬)Flat ejector pinZ466/…/S 扁顶(定制件)Flat ejector pinZ47 顶针延长杆Extension rodZ48 年月标记镶件Date insertZ4800 标记镶件Marking insertZ4801 更新标记镶件Renew insertZ481 更新年份镶件Year insertZ482 月份标记镶件Month insertZ483 年份标记镶件Year insertZ484 箭头标记镶件Arrow insertZ485 年月标记镶件Date insertZ4851 更新年份镶件Year insertZ4861/1 塑料标记镶件Resin marking insert Z4861/2 班别标记镶件Shift marking insert Z4861/3 日期标记镶件Day marking insertZ4861/4 月份标记镶件Month-marking insert Z4861/5 年份标记镶件Year-marking insert Z4863 年月日标记镶件Multi. Marking insert Z4864 年月日塑料标记镶件Multi. Marking insert Z487/1 “回收标记”嵌件Recycling insertZ487/2 “回收标记”嵌件Recycling insertZ487/3 “回收标记”嵌件Recycling insertZ488 CE 标记镶件CE marking insertZ489 食物标记镶件Food marking insert Z49 模芯镶件Core pinZ491 气动顶出阀Air valveZ492 模芯镶件Cpre pinZ495 喷气块Blow off stripZ4951 喷气咀Blow off nozzleZ50 唧咀Sprue bushingZ51 唧咀Sprue bushingZ511 唧咀Sprue bushingZ512 唧咀Sprue bushingZ515 气动唧咀Pneumatic nozzleZ516 细水口镶件Nozzle insertZ518 唧咀Sprue bushingZ519 唧咀Sprue bushingZ53 扣水口镶件Sprue pullerZ55 顶针板园垫件Stop pinZ551 顶针板园垫件Stop pinZ56 环子Head for ejector rod Z561 环子Head for ejector rod Z562 介子WasherZ57 园形垫件Support pillarZ571 园形垫件Support pillarZ60 园线弹簧Compression spring Z601 园线弹簧Compression spring Z62 蝶形弹簧Disc springZ64 方线弹簧Compression springZ65 扁线弹簧Compression spring Z67 弹弓介子环Retaining ringZ671 弹弓介子钳Mounting pliersZ68 弹弓介子环Retaining ringZ681 弹弓介子钳Mounting pliersZ69 螺丝介子Spring washerZ691 螺丝介子Spring washerZ70 吊架连吊环Lifting deviceZ701 调距螺栓Distance boltZ71 吊环Eye boltZ711 吊环Eye boltZ712 吊环Eye boltZ72 吊环Eye boltZ73 安全扣Tool safety device Z741 固定玛夹Power clampZ7411 空板架Spacer blockZ7412 空板架Spacer blockZ742 固定玛夹Power clampZ743 固定玛夹Power clampZ75 固定玛夹Clamp systemZ751 T头螺丝T head boltZ752 T头螺丝T head boltZ7521 T 头螺丝T head boltZ7522 T 头螺丝T head boltZ753 介子环Spherical washerZ754 介子环Conical seat washer Z755 介子环Conical seat washer Z76 快速玛夹模装置Quick clamping jig Z761 快速玛夹模板Clamping plateZ762 玛夹导柱Clamping boltZ763 玛夹锁钉Eccentric boltZ765 离合锁(套)Locking housingZ766 离合锁(插)Locking plugZ80 带阀快接喉套Shut-off couplingZ80/…/45 带阀快接喉套Shut-off couplingZ80/…/90 带阀快接喉套Shut-off couplingZ801 快接喉套CouplingZ801/…/45 快接喉套CouplingZ801/…/90 快接喉套CouplingZ805 带阀侨式快接喉套Diverting coupling Z8051 侨式快接喉套Diverting coupling Z807 带阀快接喉套Shut-off couplingZ807/…/45 带阀快接喉套Shut-off couplingZ807/…/90 带阀快接喉套Shut-off couplingZ808 快接喉套CouplingZ809 带阀快接喉套Multi. shut-off coupling Z81 快接喉咀NippleZ81/…/90 喉嘴NippleZ811 带阀快接喉咀Shut-off nippleZ812 适配连接头Double sided connector Z814 适配连接头AdapterZ815 适配连接头AdapterZ817 喉咀Hose nippleZ819 带阀快接喉咀Multi. shut-off nipple Z82 带阀快接喉套Shut-off couplingZ83 喉咀Hose connectorZ831 快接喉套Plug-in connectorZ84 PVC喉管PVC-HoseZ85 PVC喉管PVC-HoseZ851 PVC喉管PVC-HoseZ853 耐高温喉管Viton-HoseZ854 耐高温喉管Teflon-HoseZ855 耐高温喉管Corrugated metal hose Z86 喉箍Hose clipZ861 紧夹用喉箍Crimping sleeveZ865 紧夹用喉钳Crimping toolZ87 喉咀Hose nippleZ875 喉咀Hose nippleZ876 喉咀Hose nippleZ876/…/45 喉咀Hose nippleZ876/…/90 喉咀Hose nippleZ877 连接头Joining pieceZ878 转曲连接头ConnectorZ88 喉咀Hose nippleZ89 喉咀Hose nippleZ90 加长快接喉咀Extension nippleZ905 适配连接头AdapterZ906 延长管Extension tubeZ91 加长喉咀Extension tubeZ93 密封胶布Sealing tape (Teflon)Z94 喉塞Tapered plugZ941 喉塞Tapered plugZ942 膨胀喉塞Sealing plugZ945/1 套装拉胀喉塞工具Assembly-setZ945/2 套装拉胀喉塞工具Assembly-setZ947/1 拉胀工具延长杆Extended scale tubeZ947/2 拉胀工具延长杆Extended scale tubeZ95 钢管Brass tubeZ96 运水铝质螺旋芯(单) Spiral coreZ961 运水铝质螺旋芯(双) Spiral coreZ962 运水针Junction tubeZ964 运水回路胶环(小) Diverting elementZ9641 运水回路胶环(大) Diverting elementZ965 运水胶隔片Plug baffleZ967 隔水片Baffle coreZ968 运水胶质螺旋芯Spiral coreZ969 运水胶质螺旋芯Spiral coreZ97 运水针Cascade water junction Z975 特快导热针Heat pipeZ98 耐高温密封胶圈O-RingZ1001 阀针Needle valveZ101 电热喷咀Hot nozzleZ101G 电热喷咀Hot nozzleZ101R 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ1011 电热喷咀内胆Inner part of nozzleZ1011M 电热喷咀内胆Inner part of nozzleZ1015 金属密封圈Metall O-RingZ103 电热喷咀Hot nozzleZ103G 电热喷咀Hot nozzleZ103R 电热喷咀Hot nozzleZ1031 电热喷胆内胆Inner part of nozzleZ103T 电热喷咀Hot nozzleZ103GT 电热喷咀Hot nozzleZ103RT 电热喷咀Hot nozzleZ1031T 电热喷胆内胆Inner part of nozzleZ103M 电热喷咀Multiple gate nozzleZ1031M 电热喷胆内胆Inner part of nozzleZ10320 电热喷咀Muitlple gate nozzleZ10370 电热喷咀Muitlple gate nozzleZ104 电热喷咀Hot nozzleZ104G 电热喷咀Hot nozzleZ104R 电热喷咀Hot nozzleZ1041 电热喷胆内胆Inner part of nozzleZ104E 电热喷咀Hot nozzleZ104GE 电热喷咀Hot nozzleZ1041E 电热喷胆内胆Inner part of nozzleZ104GV 电热喷咀Hot nozzleZ1041V 电热喷咀内胆Inner part of nozzleZ10420 电热喷咀Muitlple gate nozzleZ1052 圆形隔热垫件Distance ringZ1055 炉头接驳衬套Spure bushingZ106 热流道板ManifoldZ10600 热流道板ManifoldZ1061 密封塞钉PlugZ1062 密封圈Sealing washerZ1063 六角螺丝Hexagon head screwZ1064 保温铝板Reflector sheetZ1067 套装零件Accessory kitZ107 气动针阀Needte valveZ1072 针阀司套Needle guide sleeveZ1073 针阀司套Needle guide sleeveZ1076 圆形隔热垫环Distance ringZ109 过滤器Filter cartridgeZ1095 过滤器Filter cartridgeZ110 发热棒Cartridge heaterZ111 发热棒Cartridge heaterZ1133 发热环Heater bandZ1134 发热环Heater bandZ1138 发热管(可弯曲) Fiexble heaterZ116 套装接线工具Assembly setZ1161 耐高温电线Extension cableZ1162 线耳Crimp type bracketZ1164 耐高温电线Extension cableZ1165 连接管Butt jointZ1166 线耳Cable end sleeveZ1167 套件Assembly kitZ1168 热电偶线Signal cableZ121 隔热板(洞、无洞) Insulating sheetZ1211 隔热板(洞、无洞) Thermal insulating sheetZ122 电热温控器Temperature controllerZ1221 温控器组件ModuleZ1224 插座嵌件Socket insertZ1225 温控器连接线Connection power/signal cable Z1226 温控器连接线(转换用) AdapterZ1227 插座ScoketZ1228 插座ScoketZ1229 插座嵌件InsertZ123 多组温控器Multi zone control systemZ125 温控器Temperature controllerZ126/1 温控器Temperature controllerZ126/2 温控器Temperature controllerZ1261 温控器ModuleZ1262 盖板Cover PlateZ127 插头PlugZ128 插头CouplingZ1292 多组温控器系统Multi zone control unitZ1295 热电偶ThermocoupleZ1295/1 热电偶ThermocoupleZ1295/3 热电偶ThermocoupleZ1295/5 热电偶ThermocoupleZ1296 电热固定座Coupling nippleZ1297 电热固定座Fastening nippleZ131 接线盒Wiring boxZ1312 隔热板Thermal insulating sheetZ1370 压力感应器Pressure transducerZ1371 压力感应器Measuring tongueZ1372 压力感应器Measuring measuring tongue Z1373 压力感应器Force transducerZ1381 连接线Connection cableZ1382 连接线Connection cableZ1383 连接线Connection cableZ1384/1 放大器(压-电) Charge amplifierZ1385/2 数据转换器Data converterZ1387 连接线Connection cableZ1391 替代插件DummyZ1392 固定支架BracketZ1393 替代插件DummyZ1394 固定支架BracketZ1395 固定支架Mounting plateZ1396 安装导管Spacer tubeZ1397 安装导套Mounting nutZ1398 安装导杆Tubular wrenchZ1399 安装导杆Insertion toolZ140 磁感应限位开关Limit switchZ1401 连接线Connection cableZ1402 连接线Connection cableZ141 测试表TesterZ145 红外线物体探测器Infrared control unitZ1451 红外线发送器Infrared transmitterZ1452 红外线接收器Infrared receiverZ1453 红外线发送器Infrared transmitterZ1454 红外线接收器Infrared receiverZ1455 固定支架BracketZ1457 接线盒Wiring boxZ1458 连接线Connection cableZ1460 隔热板Thermal insulating sheetZ1471 感应开关器Inductive proximity switch Z1473 感应开关器Inductive proximity switchZ1475 感应开关器Inductive proximity switch Z1500 来福线丝杆(L/左、R/右) Helical spindleZ1520 来福线丝套(L/左、R/右) Helical nutZ1540 齿条RackZ1550 带齿轮圆模芯Geared-spindle coreZ1552 螺母铜司(原料) Pilot threat bush blankZ1553 齿轮Gear wheelZ1555 齿轮Gear wheelZ1558 平键Parallel keyZ1560 圆锥滚柱轴承Roller bearingZ1562 滚珠轴承Ball bearingZ1564 滚柱压珠轴承Needle-thrust ball bearing Z1565 耐磨轴承内环Thrust ringZ1566 滚柱压柱轴承Needle-thrust roller bearing Z159 顶杆连接装置Ejector coupling deviceZ1591 连接头Coupling spigotZ1592 长接头coupling rodZ163 复位衬套Pressure sleeveZ164 复位导套BushZ165 顶板复位装置Pull back deviceZ166 复位顶出杆Ejector rodZ167 法兰盘Locking flangeZ168 快速联接装置Rapid couplingZ1681 联接杆Ejector rodZ1682 联接杆Ejector rodZ169 二级顶出装置Two-stage ejectorZ1695 二级顶出装置Two-stage ejectorZ1696 适配器AdapterZ170 程序模板开合装置Latch locking unitZ171 程序模板开合装置Latch locking unitZ172 模板开合胶塞(涨钉) Frictional pullerZ1721 模板开合胶塞(涨钉) Frictional pullerZ173 程序模板开合装置Round latch locking unitZ1731 程序模板开合拉杆Pulling rodZ1732 拉杆衬套Threaded bushZ174 程序模板开合装置Latch locking unitZ1751 斜齿条RackZ1752 斜齿条RackZ1754 斜齿条滑动方铁Guide blockZ1755 斜齿条固定方块Mounting blockZ1756 方铁Spacer blockZ1761 双面斜齿条PackZ1764 斜齿条滑动方铁Guide blockZ180 滑块SlideZ181 滑块组件Mould slide unitZ1810 锁定块Locking heelZ182 锁定块Locking heelZ1821 耐磨垫板Wear plateZ183 锁定块Duble locking heelZ1831 防磨垫板Wear plateZ1832 防磨垫板Wear plateZ185 滑块管导块Guide stripZ185W 自润滑块管导块Self lubric.Guide stripZ186W 自润滑垫板Self lubric.Flat stockZ187 斜导柱固定导套RetainerZ200 热喷嘴Hot nozzleZ2300 正向锁定液压缸Positive locking cylinderZ2310 固定块FlangeZ2320 适配器AdapterZ2330 适配器螺丝Pressure screwZ240 气动阀式开闭控制器Pneumatic control unitZ2401 摇臂式阀Rocker arm valveZ2411 油水分离器Lubro-control unitZ2412 油水分离器Lubro-control unitZ2416 消音塞SilencerZ251/2 测温表Temperature deviceZ2511 测温针Temperature feelerZ2512 测温针Temperature feelerZ2515 测温针Temperature feelerZ252 测温表Pocket temp.measuring device Z255 精度量度针规Inspection pin setZ256 针规钳Inspection pin holderZ257 精密薄垫片Gauge shim stockZ260 耐温润滑油Heavy duty lubricantZ261 耐温润滑喷剂Heavy duty lubricantZ262 防锈喷剂Heavy duty lubricantZ263 清洁喷剂Multi purpose cleaner spray Z264 矽质离模剂Silicone sprayZ265 脱模剂Release agentZ266 发热棒安装用喷剂Special assembly sprayZ267 除锈喷剂Rust solventZ268 特效润滑喷剂Teflon-lubricating sprayZ269 表面防护剂Surface protectionZ3307 注孔衬套镶件Chamber insertZ3308 密封套环Sealing ringZ3309 承托套管Spacer sieeveZ3310 电热喷咀Hot nozzleZ3340 电热喷咀Hot nozzleZ3360 电热喷咀Hot nozzleZ33201 电热喷咀Hot nozzleZ33202 电热喷咀Hot nozzleZ3500 电热喷咀Hot nozzleZ3501 电热喷咀Hot nozzleZ3510 喷咀镶件Nozzle Tip,3-hole type Z3512 喷咀镶件Nozzle Tip,1-hole type Z3520 喷咀镶件Nozzle Tip,3-hole type Z3522 喷咀镶件Nozzle Tip,1-hole type Z3550 喷咀主体Nozzle bodyZ3351 发热套HeaterZ3352 热电偶Thermo coupleZ3353 分隔帽(防止塑料滞留) Insulator capZ3554 密封环套Sealing ringZ3555 垫环Spacer discZ3556 承托套管Spacer sleeveZ3560 注孔衬套镶件Melt chamber insert Z3561 注孔衬套镶件Melt chamber insert Z3580 发热套拆卸工具Dismantling toolZ3581 六角套筒Box spannerZ3600 推缩模芯Collapslble coreZ6007 不锈钢快接喉套CouplingZ6015 不锈钢快接喉套CouplingZ6025 不锈钢快接喉套CouplingZ6055 不锈钢快接喉套CouplingZ6065 不锈钢快接喉套CouplingZ6075 不锈钢快接喉套CouplingZ6107 不锈钢带阀喉套CouplingZ6115 不锈钢带阀喉套CouplingZ6125 不锈钢带阀喉套CouplingZ6155 不锈钢带阀喉套CouplingZ6165 不锈钢带阀喉套CouplingZ6175 不锈钢带阀喉套CouplingZ6302 不锈钢快接喉套NippleZ6303 不锈钢快接喉套NippleZ6305 不锈钢加长喉咀Extended nippleZ6340 不锈钢加长喉咀Extended nippleZ6353 不锈钢带阀喉咀NippleZ6505 不锈钢喉咀Hose connectorK100 固定环Location ringK103 固定环Location ringK500 固定环Location ringK503 固定环Location ringK505 固定环Location ringA1255 洗石笔Trueing diamondA1265 Dressind stoneA1910 Cutting wheelA1915 Special grinding wheelA1930 Diamond cutting wheelA1931 Boronnitrid cutting wheel A1935 Diamond grinding wheelA1936 Boronnitrid grinding wheel A2500 锥形钻咀Tapered drillA2600 锥形镰靶Tapered reamerA2700 沉头锣刀Counter boreA2710 密封圈用坑槽锣刀Circular groove cutterA2715 固定钉Guide spigotA2720 沉头锣刀Special counter boreA2800 螺丝牙攻Tap setA3500 长方形电蚀铜料EDM copperA3501 长方形电蚀铜料EDM copperA3502 园方形电蚀铜料EDM copperA3503 园方形电蚀铜料EDM copperA3504 园方形电蚀铜料EDM copperA3510 长方形电蚀石墨料EDM GraphiteA3511 园方形电蚀石墨料EDM GraphiteA3514 长方形电蚀石墨料EDM GraphiteA3515 园方形电蚀石墨料EDM GraphiteA3541 回收再造标记石墨工Graphite electrodeA3542 回收再造标记石墨工Graphite electrodeA3543 回收再造标记石墨工Graphite electrodeA3545 CE标记铜工CE marking electrodeA3546 食品标记铜工Food marking electrodeA3547 回收再造标记铜工Recyc.Marking electrode A4700 套装气喷枪Airblow kitA4720 气喉管Spiral hoseA5000 撞激拉出工具Extraction tool kitA5050 六角匙Hexagon keyA5051 六角匙Hexagon keyA5053 六角匙Hexagon key with pilotA5055 六角匙Hexagon keyA5060 套装六角匙Hexagon key setA5061 套装六角匙Hexagon key setA5080 Slotted nut driverA5120 扳手Sickle spannerA5121 扳手Pin wrenchA5130 六角套筒Box spannerA5710 开合计数器Cycle counterA5712 可重置开合计数器Cycle counter,resetabie A5714 双合式计数器Combinedcycle counter A5716 复合式计数器Unibersal counterA5720 重置器Resetting toolsA5722 塑质固定框架Insulating frameA5723 铝质固定框架Insulating frameH1050 蕉形浇口镶件Gate insertH1060 蕉形浇口镶件Gate insertH5050 过滤器Filter cartridgeT4010 绿色扁线弹簧Compression springT4020 蓝色扁线弹簧Compression springT4030 红色扁线弹簧Compression springT4040 黄色扁线弹簧Compression spring。
(数控模具设计)HASCO模具配件中英文对照表精编
（数控模具设计）HASCO 模具配件中英文对照表HASCOZ标准件系列Z00 导柱GuidepillarZ01 导柱GuidepillarZ011 导柱GuidepillarZ012 导柱GuidepillarZ013 导柱GuidepillarZ014 导柱GuidepillarZ0141 导柱连接端EndpieceZ0142 导柱连接端EndpieceZ015 导柱GuidepillarZ0151 导柱连接端(Z015/…专用)PillaradapterZ0152 导柱连接端PillaradapterZ02 顶杆EjectorrodZ022 导管GuidesleeveZ03 导柱GuidepillarZ05 圆锥形管精定位Locatingunit,roundZ055 圆形垫片SpacerZ056 圆形垫件SpacerZ06 平锥形导块LocatingunitZ07 长方形导块SquareguidebarZ08 直身方形管位导块Pre-centeringunitZ081 方形垫片SpacerdiscZ091 方形定位锁块(公)SquareinterlockZ092 方形定位锁块(母)SquareinterlockZ093 方形定位锁块(母)SquareinterlockZ10 导套GuidebushZ10W 自润滑导套GuidebushZ11 导套GuidebushZ11W 自润滑导套GuidebushZ12 滚珠导套BallguidebushZ13W 自润滑导套Selflubricate.Guidebush Z15W 自润滑垫片Selflubricate.Flatstock Z16W 自润滑垫片Selflubricate.GuiderailZ17 长方形导块(Z07/...专用)GuideretainerZ20 定板导套CenteringsleeveZ25 定位销DowelpinZ26 定位销DowelpinZ28 六角螺母HexagonnutZ281 六角螺母HexagonnutZ282 六角螺母HexagonnutZ285 螺母NutforT-slotsZ286 螺母NutforT-slotsZ30 胚头内六角螺丝SocketheadcapscrewZ31 胚头内六角螺丝SocketheadcapscrewZ32 薄胚头内六角螺丝SocketheadcapscrewZ33 薄胚头内六角螺丝CountersunkscrewZ34 内六角螺丝Hexagonsocketsetscrew Z35 内六角螺丝Hexagonsocketsetscrew Z351 内六角螺丝Hexagonsocketsetscrew Z352 螺丝杆LockingscrewZ36 弹簧滚珠螺丝SpringplungerZ361 弹簧滚珠螺丝SpringplungerZ37 弹簧滚珠螺丝SpringplungerZ370 弹簧定位螺丝SpringplungerZ371 弹簧滚珠螺丝SpringplungerZ372 弹簧定位螺丝SpringplungerZ3721 弹簧定位螺丝SpringplungerZ373 弹簧定位镶件SpringplungerZ374 弹簧滚珠镶件SpringplungerZ375 弹簧滚珠镶件SpringplungerZ38 限位螺丝ShoulderscrewZ381 螺丝Slottedshoulderscrew Z39 螺丝Slottedshoulderscrew Z40 顶针(全硬)EjectorpinZ41 顶针(表层硬)EjectorpinZ42 顶头顶针(全硬)EjectorpinZ43 顶头顶针(表层硬)EjectorpinZ44 有托顶针(表层硬)Shoulderedejectorpin Z441 有托顶针(全硬)Shoulderedejectorpin Z442/.../S 有托顶针(定制件)EjectorpinZ45 司筒(表层硬)EjectorsleeveZ451 司筒(全硬)EjectorsleeveZ4501 司筒(全硬)EjectorsleeveZ452/…/S 司筒(定制件)EjectorsleeveZ453/…/S 司筒(定制件)EjectorsleeveZ454/…/S 司筒(定制件)EjectorsleeveZ455/…/S 司筒(定制件)EjectorsleeveZ456 顶针耐磨镶件WearsleeveZ456/…/S顶针耐磨镶件(定制件)WearsleeveZ46 扁顶针(表层硬)FlatejectorpinZ461 特殊扁顶针SpecialflatejectorZ462 特殊扁顶针镶件(Z461/…专用)GuideZ465 扁顶针(全硬)FlatejectorpinZ466/…/S 扁顶(定制件)FlatejectorpinZ47 顶针延长杆ExtensionrodZ48 年月标记镶件DateinsertZ4800 标记镶件MarkinginsertZ4801 更新标记镶件RenewinsertZ481 更新年份镶件YearinsertZ482 月份标记镶件MonthinsertZ483 年份标记镶件YearinsertZ484 箭头标记镶件ArrowinsertZ485 年月标记镶件DateinsertZ4851 更新年份镶件YearinsertZ4861/1 塑料标记镶件Resinmarkinginsert Z4861/2 班别标记镶件ShiftmarkinginsertZ4861/3 日期标记镶件DaymarkinginsertZ4861/4 月份标记镶件Month-markinginsert Z4861/5 年份标记镶件Year-markinginsertZ4863 年月日标记镶件Multi.Markinginsert Z4864 年月日塑料标记镶件Multi.MarkinginsertZ487/1 “回收标记”嵌件RecyclinginsertZ487/2 “回收标记”嵌件RecyclinginsertZ487/3 “回收标记”嵌件RecyclinginsertZ488 CE标记镶件CEmarkinginsertZ489 食物标记镶件Foodmarkinginsert Z49 模芯镶件CorepinZ491 气动顶出阀AirvalveZ492 模芯镶件CorepinZ495 喷气块BlowoffstripZ4951 喷气咀BlowoffnozzleZ50 唧咀SpruebushingZ51 唧咀SpruebushingZ511 唧咀SpruebushingZ512 唧咀SpruebushingZ515 气动唧咀Pneumaticnozzle Z516 细水口镶件NozzleinsertZ518 唧咀SpruebushingZ519 唧咀SpruebushingZ53 扣水口镶件SpruepullerZ55 顶针板园垫件StoppinZ551 顶针板园垫件StoppinZ56 环子Headforejectorrod Z561 环子Headforejectorrod Z562 介子WasherZ57 园形垫件SupportpillarZ571 园形垫件SupportpillarZ60 园线弹簧Compressionspring Z601 园线弹簧Compressionspring Z62 蝶形弹簧DiscspringZ64 方线弹簧Compressionspring Z65 扁线弹簧Compressionspring Z67 弹弓介子环RetainingringZ671 弹弓介子钳MountingpliersZ68 弹弓介子环RetainingringZ681 弹弓介子钳MountingpliersZ69 螺丝介子SpringwasherZ691 螺丝介子SpringwasherZ70 吊架连吊环LiftingdeviceZ701 调距螺栓DistanceboltZ71 吊环EyeboltZ711 吊环EyeboltZ712 吊环EyeboltZ72 吊环EyeboltZ73 安全扣Toolsafetydevice Z741 固定玛夹PowerclampZ7411 空板架SpacerblockZ7412 空板架SpacerblockZ742 固定玛夹PowerclampZ743 固定玛夹PowerclampZ75 固定玛夹ClampsystemZ751 T头螺丝TheadboltZ752 T头螺丝TheadboltZ7521 T头螺丝TheadboltZ7522 T头螺丝TheadboltZ753 介子环Sphericalwasher Z754 介子环Conicalseatwasher Z755 介子环Conicalseatwasher Z76 快速玛夹模装置Quickclampingjig Z761 快速玛夹模板ClampingplateZ762 玛夹导柱ClampingboltZ763 玛夹锁钉EccentricboltZ765 离合锁(套)LockinghousingZ766 离合锁(插)LockingplugZ80 带阀快接喉套Shut-offcoupling Z80/…/45 带阀快接喉套Shut-offcoupling Z80/…/90 带阀快接喉套Shut-offcoupling Z801 快接喉套CouplingZ801/…/45 快接喉套CouplingZ801/…/90 快接喉套CouplingZ805 带阀侨式快接喉套DivertingcouplingZ8051 侨式快接喉套DivertingcouplingZ807 带阀快接喉套Shut-offcouplingZ807/…/45 带阀快接喉套Shut-offcouplingZ807/…/90 带阀快接喉套Shut-offcouplingZ808 快接喉套CouplingZ809 带阀快接喉套Multi.shut-offcoupling Z81 快接喉咀NippleZ81/…/90 喉嘴NippleZ811 带阀快接喉咀Shut-offnippleZ812 适配连接头Doublesidedconnector Z814 适配连接头AdapterZ815 适配连接头AdapterZ817 喉咀HosenippleZ819 带阀快接喉咀Multi.shut-offnipple Z82 带阀快接喉套Shut-offcouplingZ83 喉咀HoseconnectorZ831 快接喉套Plug-inconnectorZ84 PVC喉管PVC-HoseZ85 PVC喉管PVC-HoseZ851 PVC喉管PVC-HoseZ853 耐高温喉管Viton-HoseZ854 耐高温喉管Teflon-HoseZ855 耐高温喉管Corrugatedmetalhose Z86 喉箍HoseclipZ861 紧夹用喉箍CrimpingsleeveZ865 紧夹用喉钳CrimpingtoolZ87 喉咀HosenippleZ875 喉咀HosenippleZ876 喉咀HosenippleZ876/…/45 喉咀HosenippleZ876/…/90 喉咀HosenippleZ877 连接头JoiningpieceZ878 转曲连接头ConnectorZ88 喉咀HosenippleZ89 喉咀HosenippleZ90 加长快接喉咀ExtensionnippleZ905 适配连接头AdapterZ906 延长管ExtensiontubeZ91 加长喉咀ExtensiontubeZ93 密封胶布Sealingtape(Teflon) Z94 喉塞TaperedplugZ941 喉塞TaperedplugZ942 膨胀喉塞SealingplugZ945/1 套装拉胀喉塞工具Assembly-setZ945/2 套装拉胀喉塞工具Assembly-setZ947/1 拉胀工具延长杆ExtendedscaletubeZ947/2 拉胀工具延长杆ExtendedscaletubeZ95 钢管BrasstubeZ96 运水铝质螺旋芯(单) SpiralcoreZ961 运水铝质螺旋芯(双) SpiralcoreZ962 运水针JunctiontubeZ964 运水回路胶环(小) DivertingelementZ9641 运水回路胶环(大) DivertingelementZ965 运水胶隔片PlugbaffleZ967 隔水片BafflecoreZ968 运水胶质螺旋芯SpiralcoreZ969 运水胶质螺旋芯SpiralcoreZ97 运水针Cascadewaterjunction Z975 特快导热针HeatpipeZ98 耐高温密封胶圈O-RingZ1001 阀针NeedlevalveZ101 电热喷咀HotnozzleZ101G 电热喷咀HotnozzleZ101R 电热喷咀HotnozzleZ101M 电热喷咀HotnozzleZ101M 电热喷咀HotnozzleZ1011 电热喷咀内胆Innerpartofnozzle Z1011M 电热喷咀内胆Innerpartofnozzle Z1015 金属密封圈MetalO-RingZ103 电热喷咀HotnozzleZ103G 电热喷咀HotnozzleZ103R 电热喷咀HotnozzleZ1031 电热喷胆内胆Innerpartofnozzle Z103T 电热喷咀HotnozzleZ103GT 电热喷咀HotnozzleZ103RT 电热喷咀HotnozzleZ1031T 电热喷胆内胆Innerpartofnozzle Z103M 电热喷咀Multiplegatenozzle Z1031M 电热喷胆内胆Innerpartofnozzle Z10320 电热喷咀Muitlplegatenozzle Z10370 电热喷咀Muitlplegatenozzle Z104 电热喷咀HotnozzleZ104G 电热喷咀HotnozzleZ104R 电热喷咀HotnozzleZ1041 电热喷胆内胆Innerpartofnozzle Z104E 电热喷咀HotnozzleZ104GE 电热喷咀HotnozzleZ1041E 电热喷胆内胆Innerpartofnozzle Z104GV 电热喷咀HotnozzleZ1041V 电热喷咀内胆Innerpartofnozzle Z10420 电热喷咀Muitlplegatenozzle Z1052 圆形隔热垫件DistanceringZ1055 炉头接驳衬套SpruebushingZ106 热流道板ManifoldZ10600 热流道板ManifoldZ1061 密封塞钉PlugZ1062 密封圈SealingwasherZ1063 六角螺丝Hexagonheadscrew Z1064 保温铝板ReflectorsheetZ1067 套装零件AccessorykitZ107 气动针阀NeedlevalveZ1072 针阀司套NeedleguidesleeveZ1073 针阀司套NeedleguidesleeveZ1076 圆形隔热垫环DistanceringZ109 过滤器FiltercartridgeZ1095 过滤器FiltercartridgeZ110 发热棒CartridgeheaterZ111 发热棒CartridgeheaterZ1133 发热环HeaterbandZ1134 发热环HeaterbandZ1138 发热管(可弯曲) FiexbleheaterZ116 套装接线工具AssemblysetZ1161 耐高温电线ExtensioncableZ1162 线耳CrimptypebracketZ1164 耐高温电线ExtensioncableZ1165 连接管ButtjointZ1166 线耳CableendsleeveZ1167 套件AssemblykitZ1168 热电偶线SignalcableZ121 隔热板(洞、无洞) InsulatingsheetZ1211 隔热板(洞、无洞) Thermalinsulatingsheet Z122 电热温控器Temperaturecontroller Z1221 温控器组件ModuleZ1224 插座嵌件SocketinsertZ1225 温控器连接线Connectionpower/signalcableZ1226 温控器连接线(转换用) AdapterZ1227 插座ScoketZ1228 插座ScoketZ1229 插座嵌件InsertZ123 多组温控器Multizonecontrolsystem Z125 温控器Temperaturecontroller Z126/1 温控器Temperaturecontroller Z126/2 温控器TemperaturecontrollerZ1261 温控器ModuleZ1262 盖板CoverPlateZ127 插头PlugZ128 插头CouplingZ1292 多组温控器系统MultizonecontrolunitZ1295 热电偶ThermocoupleZ1295/1 热电偶ThermocoupleZ1295/3 热电偶ThermocoupleZ1295/5 热电偶ThermocoupleZ1296 电热固定座CouplingnippleZ1297 电热固定座FasteningnippleZ131 接线盒WiringboxZ1312 隔热板Thermalinsulatingsheet Z1370 压力感应器PressuretransducerZ1371 压力感应器MeasuringtongueZ1372 压力感应器MeasuringmeasuringtongueZ1373 压力感应器ForcetransducerZ1381 连接线ConnectioncableZ1382 连接线ConnectioncableZ1383 连接线ConnectioncableZ1384/1 放大器(压-电) ChargeamplifierZ1385/2 数据转换器DataconverterZ1387 连接线ConnectioncableZ1391 替代插件DummyZ1392 固定支架BracketZ1393 替代插件DummyZ1394 固定支架BracketZ1395 固定支架MountingplateZ1396 安装导管SpacertubeZ1397 安装导套MountingnutZ1398 安装导杆TubularwrenchZ1399 安装导杆InsertiontoolZ140 磁感应限位开关LimitswitchZ1401 连接线ConnectioncableZ1402 连接线ConnectioncableZ141 测试表TesterZ145 红外线物体探测器InfraredcontrolunitZ1451 红外线发送器InfraredtransmitterZ1452 红外线接收器InfraredreceiverZ1453 红外线发送器InfraredtransmitterZ1454 红外线接收器InfraredreceiverZ1455 固定支架BracketZ1457 接线盒WiringboxZ1458 连接线ConnectioncableZ1460 隔热板Thermalinsulatingsheet Z1471 感应开关器Inductiveproximityswitch Z1473 感应开关器Inductiveproximityswitch Z1475 感应开关器Inductiveproximityswitch Z1500 来福线丝杆(L/左、R/右) HelicalspindleZ1520 来福线丝套(L/左、R/右) HelicalnutZ1540 齿条RackZ1550 带齿轮圆模芯Geared-spindlecoreZ1552 螺母铜司(原料) PilotthreatbushblankZ1553 齿轮GearwheelZ1555 齿轮GearwheelZ1558 平键ParallelkeyZ1560 圆锥滚柱轴承RollerbearingZ1562 滚珠轴承BallbearingZ1564 滚柱压珠轴承Needle-thrustballbearing Z1565 耐磨轴承内环ThrustringZ1566 滚柱压柱轴承Needle-thrustrollerbearingZ159 顶杆连接装置EjectorcouplingdeviceZ1591 连接头CouplingspigotZ1592 长接头couplingrodZ163 复位衬套PressuresleeveZ164 复位导套BushZ165 顶板复位装置PullbackdeviceZ166 复位顶出杆EjectorrodZ167 法兰盘LockingflangeZ168 快速联接装置RapidcouplingZ1681 联接杆EjectorrodZ1682 联接杆EjectorrodZ169 二级顶出装置Two-stageejectorZ1695 二级顶出装置Two-stageejectorZ1696 适配器AdapterZ170 程序模板开合装置LatchlockingunitZ171 程序模板开合装置LatchlockingunitZ172 模板开合胶塞(涨钉) FrictionalpullerZ1721 模板开合胶塞(涨钉) FrictionalpullerZ173 程序模板开合装置Roundlatchlockingunit Z1731 程序模板开合拉杆PullingrodZ1732 拉杆衬套ThreadedbushZ174 程序模板开合装置LatchlockingunitZ1751 斜齿条RackZ1752 斜齿条RackZ1754 斜齿条滑动方铁GuideblockZ1755 斜齿条固定方块MountingblockZ1756 方铁SpacerblockZ1761 双面斜齿条PackZ1764 斜齿条滑动方铁GuideblockZ180 滑块SlideZ181 滑块组件MouldslideunitZ1810 锁定块LockingheelZ182 锁定块LockingheelZ1821 耐磨垫板WearplateZ183 锁定块DublelockingheelZ1831 防磨垫板WearplateZ1832 防磨垫板WearplateZ185 滑块管导块GuidestripZ185W 自润滑块管导块Selflubric.GuidestripZ186W 自润滑垫板Selflubric.FlatstockZ187 斜导柱固定导套RetainerZ200 热喷嘴HotnozzleZ2300 正向锁定液压缸Positivelockingcylinder Z2310 固定块FlangeZ2320 适配器AdapterZ2330 适配器螺丝PressurescrewZ240 气动阀式开闭控制器PneumaticcontrolunitZ2401 摇臂式阀RockerarmvalveZ2411 油水分离器Lubro-controlunitZ2412 油水分离器Lubro-controlunitZ2416 消音塞SilencerZ251/2 测温表TemperaturedeviceZ2511 测温针TemperaturefeelerZ2512 测温针TemperaturefeelerZ2515 测温针TemperaturefeelerZ252 测温表Pockettemp.measuringdeviceZ255 精度量度针规InspectionpinsetZ256 针规钳InspectionpinholderZ257 精密薄垫片GaugeshimstockZ260 耐温润滑油HeavydutylubricantZ261 耐温润滑喷剂HeavydutylubricantZ262 防锈喷剂HeavydutylubricantZ263 清洁喷剂MultipurposecleanersprayZ264 矽质离模剂SiliconesprayZ265 脱模剂ReleaseagentZ266 发热棒安装用喷剂SpecialassemblysprayZ267 除锈喷剂RustsolventZ268 特效润滑喷剂Teflon-lubricatingspray Z269 表面防护剂SurfaceprotectionZ3307 注孔衬套镶件ChamberinsertZ3308 密封套环SealingringZ3309 承托套管SpacersieeveZ3310 电热喷咀HotnozzleZ3340 电热喷咀HotnozzleZ3360 电热喷咀HotnozzleZ33201 电热喷咀HotnozzleZ33202 电热喷咀HotnozzleZ3500 电热喷咀HotnozzleZ3501 电热喷咀HotnozzleZ3510 喷咀镶件NozzleTip,3-holetype Z3512 喷咀镶件NozzleTip,1-holetype Z3520 喷咀镶件NozzleTip,3-holetype Z3522 喷咀镶件NozzleTip,1-holetype Z3550 喷咀主体NozzlebodyZ3351 发热套HeaterZ3352 热电偶ThermocoupleZ3353 分隔帽(防止塑料滞留) InsulatorcapZ3554 密封环套SealingringZ3555 垫环SpacerdiscZ3556 承托套管SpacersleeveZ3560 注孔衬套镶件Meltchamberinsert Z3561 注孔衬套镶件Meltchamberinsert Z3580 发热套拆卸工具DismantlingtoolZ3581 六角套筒BoxspannerZ3600 推缩模芯CollapslblecoreZ6007 不锈钢快接喉套CouplingZ6015 不锈钢快接喉套CouplingZ6025 不锈钢快接喉套CouplingZ6055 不锈钢快接喉套CouplingZ6065 不锈钢快接喉套CouplingZ6075 不锈钢快接喉套CouplingZ6107 不锈钢带阀喉套CouplingZ6115 不锈钢带阀喉套CouplingZ6125 不锈钢带阀喉套CouplingZ6155 不锈钢带阀喉套CouplingZ6165 不锈钢带阀喉套CouplingZ6175 不锈钢带阀喉套CouplingZ6302 不锈钢快接喉套NippleZ6303 不锈钢快接喉套NippleZ6305 不锈钢加长喉咀ExtendednippleZ6340 不锈钢加长喉咀ExtendednippleZ6353 不锈钢带阀喉咀NippleZ6505 不锈钢喉咀HoseconnectorK100 固定环LocationringK103 固定环LocationringK500 固定环LocationringK503 固定环LocationringK505 固定环LocationringA1255 洗石笔TrueingdiamondA1265 DressindstoneA1910 CuttingwheelA1915 SpecialgrindingwheelA1930 DiamondcuttingwheelA1931 Boronnitridcuttingwheel A1935 Diamondgrindingwheel A1936 Boronnitridgrindingwheel A2500 锥形钻咀TapereddrillA2600 锥形镰靶TaperedreamerA2700 沉头锣刀CounterboreA2710 密封圈用坑槽锣刀CirculargroovecutterA2715 固定钉GuidespigotA2720 沉头锣刀SpecialcounterboreA2800 螺丝牙攻TapsetA3500 长方形电蚀铜料EDMcopperA3501 长方形电蚀铜料EDMcopperA3502 园方形电蚀铜料EDMcopperA3503 园方形电蚀铜料EDMcopperA3504 园方形电蚀铜料EDMcopperA3510 长方形电蚀石墨料EDMGraphiteA3511 园方形电蚀石墨料EDMGraphiteA3514 长方形电蚀石墨料EDMGraphiteA3515 园方形电蚀石墨料EDMGraphiteA3541 回收再造标记石墨工GraphiteelectrodeA3542 回收再造标记石墨工GraphiteelectrodeA3543 回收再造标记石墨工GraphiteelectrodeA3545 CE标记铜工CEmarkingelectrodeA3546 食品标记铜工Foodmarkingelectrode A3547 回收再造标记铜工Recyc.Markingelectrode A4700 套装气喷枪AirblowkitA4720 气喉管SpiralhoseA5000 撞激拉出工具ExtractiontoolkitA5050 六角匙HexagonkeyA5051 六角匙HexagonkeyA5053 六角匙Hexagonkeywithpilot A5055 六角匙HexagonkeyA5060 套装六角匙HexagonkeysetA5061 套装六角匙HexagonkeysetA5080 SlottednutdriverA5120 扳手SicklespannerA5121 扳手PinwrenchA5130 六角套筒BoxspannerA5710 开合计数器CyclecounterA5712 可重置开合计数器Cyclecounter,resetabie A5714 双合式计数器Combinedcyclecounter A5716 复合式计数器UnibersalcounterA5720 重置器ResettingtoolsA5722 塑质固定框架InsulatingframeA5723 铝质固定框架InsulatingframeH1050 蕉形浇口镶件GateinsertH1060 蕉形浇口镶件GateinsertH5050 过滤器FiltercartridgeT4010 绿色扁线弹簧CompressionspringT4020 蓝色扁线弹簧CompressionspringT4030 红色扁线弹簧Compressionspring T4040 黄色扁线弹簧Compressionspring。
hasco标准件的中英文对照1
Z80/…/90 带阀快接喉套 Shut-off coupling
Z801 快接喉套 Coupling
Z801/…/45 快接喉套 Coupling
Z801/…/90 快接喉套 Coupling
Z805 带阀侨式快接喉套 Diverting coupling
Z456/…/S 顶针耐磨镶件(定制件) Wear sleeve
Z46 扁顶针(表层硬) Flat ejector pin
Z461 特殊扁顶针 Special flat ejector
Z462 特殊扁顶针镶件(Z461/…专用) Guide
Z465 扁顶针(全硬) Flat ejector pin
Z11 导套 Guide bush
Z11W 自润滑导套 Guide bush
Z12 滚珠导套 Ball guide bush
Z13W 自润滑导套 Self lubric.Guide bush
Z15W 自润滑垫片 Self lubric. Flat stock
Z16W 自润滑垫片 Self lubric. Guide rail
Z489 食物标记镶件 Food marking insert
Z49 模芯镶件 Core pin
Z491 气动顶出阀 Air valve
Z492 模芯镶件 Cpre pin
Z495 喷气块 Blow off strip
Z4951 喷气咀 Blow off nozzle
Z50 唧咀 Sprue bushing
Z53 扣水口镶件 Sprue puller
Z55 顶针板园垫件 Stop pin
模具各零部件名称中英文对照
split mold分割式模具
cavity型控 母模
core模心 公模
taper锥拔
leather cloak仿皮革
shiver饰纹
flow mark流痕
welding mark溶合痕
post screw insert螺纹套筒埋值
Moving clamp plate
基准线datum line
基准面datum plan
型芯固定板core-retainer plate
凸模固定板punch-retainer plate
顶针ejector pin
单腔模具single cavity mould
多腔模具multi-cavity mould
螺杆screw
麻点pit
嵌件insert
活动镶件movable insert
起垩chalking
浇注系统feed system
主流道 sprue
分流道runner
浇口gate
直浇口direct gate , sprue gate
轮辐浇口spoke gate , spider gate
圆弧齿（锉刀） gleason tooth なみめ)波目
圆弧连接孔的波形高 circular arc switch port waveform high えんこ)円弧ニブリング加工の山の高さ
圆角 corner radius コーナR
圆孔场合 round orifice occasion まるけいじょうのばあい)丸形状の場合
去磁机Demagnetization machine
模具中英文参照表
模具中英文参照表模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割Wire E.D.M轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap导柱位Leader Pin Location 耐落胶Teflon Paste 偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weldline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring 管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水口铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch 斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin 顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring 管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹） Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形warping走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板 A'plateB板 B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary 丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板Cover Plate 齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag 线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High Volume Running Mold剖面图Cross Section模具结构Mold Construction模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension 模具完成日 completion date 雕刻Engrave托司 EJ.GUIDE PIN烧焊 Welding浇口 gate侧胶式 side gate潜伏式 sub gate热流道 hot runner阀浇式（大水口直接进胶）direct gate扇形式 fan gate手折式 break off gate点浇式 pin point gate单边打入子 runner insert gate搭接式浇口 tab gate隧道式澆口 tunnel gate牛角进胶 cashew gate/banana gate成型材料Injection material生产数（模具寿命）production volume二次加工second process投影面积projected area流动平衡 Equal flow coming out 锁模力 clamping force 成型机injection machine成型周期cycle time模具结构 mold construction模胚 Mold Base定位环 locating ring面板 top plate唧嘴 sprue流道 runner主流道 main runner分流道 side runnerA板 A plate导套 Bushing导柱 Leader Pin回针 Return Pin上模小镶件Cavity Sub-Insert 上模镶件Cavity Block行位Slide行位镶件Slide Insert压紧块（铲机）Jaw压条Gib后模 core小镶件Sub-Insert下模镶件Core Block下模小镶件Core Sub-Insert 料花 splay mark粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warping走水不平均Filling Uneven 走不齐Short Shot毛边 flash困气air trapping结合线 welding line熔接痕welding mark缩水 sink mark顶白 stress mark漏水Water Leakage刮花（擦伤）Galling火山口 crater液压油缸 hydraulic cylinder。
haso标准件中英文对照
haso标准件中英文对照HASCO Z标准件系列Z00 导柱Guide pillarZ01 导柱Guide pillarZ011 导柱Guide pillarZ012 导柱Guide pillarZ013 导柱Guide pillarZ014 导柱Guide pillarZ0141 导柱连接端End p ieceZ0142 导柱连接端End p ieceZ015 导柱Guide pillarZ0151 导柱连接端（Z015/…专用）Pillar ada pter Z0152 导柱连接端Pillar ada pterZ02 顶杆Ejector rodZ022 导管Guide sleeveZ03 导柱Guide pillarZ05 圆锥形管精定位Locating unit, roundZ055 圆形垫片SpacerZ056 圆形垫件SpacerZ06 平锥形导块Locating unitZ07 长方形导块Square guide barZ08 直身方形管位导块Pre-centering unitZ081 方形垫片Sp acer discZ091 方形定位锁块（公）Square interlockZ092 方形定位锁块（母）Square interlockZ093 方形定位锁块（母）Square interlockZ10 导套Guide bushZ10W 自润滑导套Guide bushZ11 导套Guide bushZ11W 自润滑导套Guide bushZ12 滚珠导套Ball guide bushZ13W 自润滑导套Self lubric.Guide bush Z15W 自润滑垫片Self lubric. Flat stock Z16W 自润滑垫片Self lubric. Guide rail Z17 长方形导块（Z07/...专用）Guide retainerZ20 定板导套Centering sleeveZ25 定位销Dowel pinZ26 定位销Dowel pinZ28 六角螺母Hexagon nutZ281 六角螺母Hexagon nutZ282 六角螺母Hexagon nutZ285 螺母Nut for T-slotsZ286 螺母Nut for T-slotsZ30 胚头内六角螺丝Socket head cap screwZ31 胚头内六角螺丝Socket head cap screwZ32 薄胚头内六角螺丝Socket head cap screwZ33 薄胚头内六角螺丝Countersunk screwZ34 内六角螺丝Hexagon socket set screw Z35 内六角螺丝Hexagon socket set screw Z351 内六角螺丝Hexagon socket set screw Z352 螺丝杆Locking screwZ36 弹簧滚珠螺丝Sp ring pl ungerZ361 弹簧滚珠螺丝Sp ring pl ungerZ37 弹簧滚珠螺丝Sp ring pl ungerZ370 弹簧定位螺丝Sp ring pl ungerZ371 弹簧滚珠螺丝Sp ring pl ungerZ372 弹簧定位螺丝Sp ring pl ungerZ3721 弹簧定位螺丝Sp ring pl ungerZ373 弹簧定位镶件Sp ring pl ungerZ374 弹簧滚珠镶件Sp ring pl ungerZ375 弹簧滚珠镶件Sp ring pl ungerZ38 限位螺丝Shoulder screwZ381 螺丝Slotted shoulder screw Z39 螺丝Slotted shoulder screw Z40 顶针（全硬）Ejector pinZ41 顶针（表层硬）Ejector pinZ42 顶头顶针（全硬）Ejector pinZ43 顶头顶针（表层硬）Ejector pinZ44 有托顶针（表层硬）Shouldered ejector pin Z441 有托顶针（全硬）Shouldered ejector pin Z442/.../S 有托顶针（定制件）Ejector pinZ45 司筒（表层硬）Ejector sleeveZ451 司筒（全硬）Ejector sleeveZ4501 司筒（全硬）Ejector sleeveZ452/ -/S 司筒（定制件）Ejector sleeveZ453/ -/S 司筒（定制件）Ejector sleeveZ454/ …/S 司筒（定制件）Ejector sleeveZ455/ …/S 司筒（定制件）Ejector sleeveZ456 顶针耐磨镶件Wear sleeveZ456/…/S 顶针耐磨镶件（定制件）Wear sleeveZ46 扁顶针（表层硬）Flat ejector pinZ461 特殊扁顶针Sp ecial flat ejectorZ462 特殊扁顶针镶件（Z461/…专用）GuideZ465 扁顶针（全硬）Flat ejector pinZ466/ …/S 扁顶（定制件）Flat ejector pinZ47 顶针延长杆Extension rodZ48 年月标记镶件Date insertZ4800 标记镶件Marking insertZ4801 更新标记镶件Renew insertZ481 更新年份镶件Year insertZ482 月份标记镶件Month insertZ483 年份标记镶件Year insertZ484 箭头标记镶件Arrow insertZ485 年月标记镶件Date insertZ4851 更新年份镶件Year insertZ4861/1 塑料标记镶件Resin marking insert Z4861/2 班别标记镶件Shift marking insert Z4861/3 日期标记镶件Day marking insertZ4861/4 月份标记镶件Month-marking insert Z4861/5 年份标记镶件Year-marking insert Z4863 年月日标记镶件Multi. Marking insert Z4864 年月日塑料标记镶件Multi. Marking insert Z487/1 “回收标记”嵌件Recycling insertZ487/2 “回收标记”嵌件Recycling insertZ487/3 “回收标记”嵌件Recycling insertZ488 CE标记镶件CE marking insertZ489 食物标记镶件Food marking insert Z49 模芯镶件Core pin Z491 气动顶出阀Air valveZ492 模芯镶件Cpre pinZ495 喷气块Blow off stripZ4951 喷气咀Blow off nozzleZ50 唧咀Sprue bushingZ51 唧咀Sprue bushingZ511 唧咀Sprue bushingZ512 唧咀Sprue bushingZ515 气动唧咀Pneumatic nozzleZ516 细水口镶件Nozzle insertZ518 唧咀Sprue bushingZ519 唧咀Sprue bushingZ53 扣水口镶件Sprue p ullerZ55 顶针板园垫件Stop pinZ551 顶针板园垫件Stop pinZ56 环子Head for ejector rod Z561 环子Head for ejector rodZ562 介子WasherZ57 园形垫件Support p illarZ571 园形垫件Support p illarZ60 园线弹簧Comp ression sp ring Z601 园线弹簧Comp ression sp ring Z62 蝶形弹簧Disc sp ringZ64 方线弹簧Comp ression sp ringZ65 扁线弹簧Comp ression sp ring Z67 弹弓介子环Retaining ringZ671 弹弓介子钳Mounting p liersZ68 弹弓介子环Retaining ringZ681 弹弓介子钳Mounting p liersZ69 螺丝介子Sp ring washerZ691 螺丝介子Sp ring washerZ70 吊架连吊环Lifting deviceZ701 调距螺栓Distance boltZ71 吊环Eye boltZ711 吊环Eye boltZ712 吊环Eye boltZ72 吊环Eye boltZ73 安全扣T ool safety device Z741 固定玛夹Power clam pZ7411 空板架Sp acer blockZ7412 空板架Sp acer blockZ742 固定玛夹Power clam pZ743 固定玛夹Power clam pZ75 固定玛夹Clam p systemZ751 T头螺丝T head boltZ752 T头螺丝T head boltZ7521 T头螺丝T head boltZ7522 T头螺丝T head boltZ753 介子环Sp herical washerZ754 介子环Conical seat washer Z755 介子环Conical seat washer Z76 快速玛夹模装置Quick clam ping jig Z761 快速玛夹模板Clam ping p lateZ762 玛夹导柱Clam ping boltZ763 玛夹锁钉Eccentric boltZ765 离合锁（套）Locking housingZ766 离合锁（插）Locking plugZ80 带阀快接喉套Shut-off coup ling Z80/ …/45 带阀快接喉套Shut-off coup ling Z80/ …/90 带阀快接喉套Shut-off coup ling Z801 快接喉套Coup lingZ801/…/45 快接喉套Coup lingZ801/…/90 快接喉套Coup lingZ805 带阀侨式快接喉套Diverting coup ling Z8051 侨式快接喉套Diverting coup ling Z807 带阀快接喉套Shut-off coup ling Z807/ …/45 带阀快接喉套Shut-off coup ling Z807/ …/90 带阀快接喉套Shut-off coup lingZ808 快接喉套Coup lingZ809 带阀快接喉套Multi. shut-off couplingZ81 快接喉咀Nipp leZ81/ …/90 喉嘴Nipp leZ811 带阀快接喉咀Shut-off ni ppleZ812 适配连接头Double sided connector Z814 适配连接头Ada pterZ815 适配连接头Ada pterZ817 喉咀Hose nippleZ819 带阀快接喉咀Multi. shut-off ni pp le Z82 带阀快接喉套Shut-off coup lingZ83 喉咀Hose connectorZ831 快接喉套Plug-in connectorZ84 PVC喉管PVC-HoseZ85 PVC喉管PVC-HoseZ851 PVC喉管PVC-HoseZ853 耐高温喉管Viton-HoseZ854 耐高温喉管T eflon-HoseZ855 耐高温喉管Corrugated metal hoseZ86 喉箍Hose cli pZ861 紧夹用喉箍Crim ping sleeveZ865 紧夹用喉钳Crim ping toolZ87 喉咀Hose nippleZ875 喉咀Hose nippleZ876 喉咀Hose nippleZ876/ …/45 喉咀Hose nippleZ876/ …/90 喉咀Hose nippleZ877 连接头Joining p ieceZ878 转曲连接头ConnectorZ88 喉咀Hose nippleZ89 喉咀Hose nippleZ90 加长快接喉咀Extension nippleZ905 适配连接头Ada pterZ906 延长管Extension tubeZ91 加长喉咀Extension tubeZ93 密封胶布Sealing tape (Teflon)Z94 喉塞Tap ered plugZ941 喉塞Tap ered plugZ942 膨胀喉塞Sealing plugZ945/1 套装拉胀喉塞工具Assembly-setZ945/2 套装拉胀喉塞工具Assembly-setZ947/1 拉胀工具延长杆Extended scale tube Z947/2 拉胀工具延长杆Extended scale tubeZ95 钢管Brass tubeZ96 运水铝质螺旋芯（单）Sp iral coreZ961 运水铝质螺旋芯（双）Sp iral coreZ962 运水针Junction tubeZ964 运水回路胶环（小）Diverting elementZ9641 运水回路胶环（大）Diverting elementZ965 运水胶隔片Plug baffleZ967 隔水片Baffle coreZ968 运水胶质螺旋芯Sp iral coreZ969 运水胶质螺旋芯Sp iral coreZ97 运水针Cascade water junction Z975 特快导热针Heat pipe Z98 耐高温密封胶圈O-RingZ1001 阀针Needle valveZ101 电热喷咀Hot nozzleZ101G 电热喷咀Hot nozzleZ101R 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ1011 电热喷咀内胆Inner part of nozzle Z1011M 电热喷咀内胆Inner part of nozzle Z1015 金属密圭寸圈Metall O-Ring Z103 电热喷咀Hot nozzleZ103G 电热喷咀Hot nozzleZ103R 电热喷咀Hot nozzleZ1031 电热喷胆内胆Inner part of nozzle Z103T 电热喷咀Hot nozzleZ103GT 电热喷咀Hot nozzleZ103RT 电热喷咀Hot nozzleZ103 仃电热喷胆内胆Inner part of nozzle Z103M 电热喷咀Multi ple gate nozzle Z1031M 电热喷胆内胆Inner part of nozzle Z10320 电热喷咀Muitl ple gate nozzle Z10370 电热喷咀Muitl plegate nozzle Z104 电热喷咀Hot nozzleZ104G 电热喷咀Hot nozzleZ104R 电热喷咀Hot nozzleZ1041 电热喷胆内胆Inner part of nozzle Z104E 电热喷咀Hot nozzleZ104GE 电热喷咀Hot nozzleZ1041E 电热喷胆内胆Inner part of nozzle Z104GV 电热喷咀Hot nozzleZ1041V 电热喷咀内胆Inner part of nozzle Z10420 电热喷咀Muitl ple gate nozzle Z1052 圆形隔热垫件Distance ring Z1055 炉头接驳衬套Spure bushingZ106 热流道板ManifoldZ10600 热流道板ManifoldZ1061 密封塞钉P lugZ1062 密圭寸圈Sealing washerZ1063 六角螺丝Hexagon head screwZ1064 保温铝板Reflector sheetZ1067 套装零件Accessory kitZ107 气动针阀Needte valveZ1072 针阀司套Needle guide sleeveZ1073 针阀司套Needle guide sleeveZ1076 圆形隔热垫环Distance ringZ109 过滤器Filter cartridgeZ1095 过滤器Filter cartridgeZ110 发热棒Cartridge heaterZ111 发热棒Cartridge heaterZ1133 发热环Heater bandZ1134 发热环Heater bandZ1138 发热管（可弯曲）Fiexble heaterZ116 套装接线工具Assembly setZ1161 耐高温电线Extension cableZ1162 线耳Crimp type bracketZ1164 耐高温电线Extension cableZ1165 连接管Butt jointZ1166 线耳Cable end sleeveZ1167 套件Assembly kitZ1168 热电偶线Signal cableZ121 隔热板（洞、无洞）Insulating sheetZ1211 隔热板（洞、无洞）Thermal insulating sheetZ122 电热温控器T em perature controllerZ1221 温控器组件ModuleZ1224 插座嵌件Socket insertZ1225 温控器连接线Connection po wer/signal cable Z1226 温控器连接线（转换用）Ada pterZ1227 插座ScoketZ1228 插座ScoketZ1229 插座嵌件InsertZ123 多组温控器Multi zone control systemZ125 温控器T em perature controllerZ126/1 温控器T em perature controllerZ126/2 温控器T em perature controllerZ1261 温控器ModuleZ1262 盖板Cover PlateZ127 插头P lug。
模具零配件中英文对照
常用模具零件中英文对照表2005-12-19 14:51:17 中国注塑网入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞:pipeplug锁模块：lockplate斜顶：anglefrompin斜顶杆：angleejectorrod尼龙拉勾：partinglocks活动臂：leverarm复位键、提前回杆：earlyreturnbar气阀：valves斜导边：anglepin术语：terms承压平面平衡：partingsurfacesupportbalance模排气：partinglineventing回针碰料位：returnpinandcavityinterference模总高超出啤机规格：moldbaseshuthight顶针碰运水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate. 不准用镶件：Donotuse(core/cavity)insert用铍铜做镶件：useberylliumcopperinsert初步（正式）模图设计：preliinary(final)molddesign反呵：reversecore弹弓压缩量：springcompressedlength稳定性好：goodstability,stable强度不够：insufficientrigidity均匀冷却：evencooling扣模：sticking热膨胀：theroexpansion公差：tolorance铜公(电极）：copperelectrodecompre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具encapsulation molding 低压封装成型、射出成型用模具two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location 定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块electrical discharge machining (EDM) 电火花加工electrical insulating property 电绝缘性能electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床electrochemical machine (ECM) 电解加工机床，电化学加工机床electrochemical machining (ECM) 电解加工，电化学加工electro-discharge cutting 电火花加工，电火花切割electro-discharge cutting machine 电火花切割机electro-discharge machine tool 电火花加工机床Electro-discharge Machine 电火花加工机床electro-discharge machining 电火花加工electro-discharge machining process 电火花加工工艺，电火花加工工序epoxy resin 环氧树脂guide bushing 导套guide pillar 导柱，导杆，导柱guide pin 导向销，导杆guide pin cover 导柱盖guide plate 导料板，导板guide plate blanking die 导板式冲裁模，导板式落料模guide post 导柱，导柱guide stock plate 挡料板injection mold 注射模，注塑模injection molding 注射成型，注塑成型injection-molding machine 注塑机，注射机，注塑成形机injection plunger 注射柱塞in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆inner ram 内滑块inserting molding 嵌件成形integrated manufacturing 集成制造internal stress 内应力13.intermediate platen 中间板，隔板塑料成型模具的主要设计要素脱模距stripper distance脱模斜度draft投影面积projected area最大开距maximum daylight;open daylight闭合高度mould-shut height抽芯距core-pulling distance抽芯力core-pulling force脱模力ejector force开模力mould opening force模内压力internal mould pressure;cavity pressure成型压力moulding pressure背压环back-up ring 1 bar = 14.5psi高压接头bite type fitting液压马达hydraulic motor冷却水流量计waterflow regulator打磨器材abrasive material打磨砂轮grinding wheels切割砂轮cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具piping tools高压力软管high pressure hose风管,水软管air .water hose高压油表pressure gauge压力油喉hydraulic hoses光塑检测photoelastic testing吹塑模plastic blow mould注塑模plastic injection mould冲扎复合模blank & form compound die精密冲模precision blanking die熔料流动率MFR=melt flow rate熔料流动指数MET=melt flow index推板导柱guide pin for ejector plater座板clamping plate垫块space block(plate)推板ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形distortion弯曲warp拖花drag marks火花纹EDM marks困气venting烧黑burns表面缩水shrinkage料位过薄/砸穿thin wall stock走水不平行uneven fill pattern夹水纹/流纹witness line;mismatch;stress marks 走水纹knit lines走水不齐short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴ensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (分离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的部分,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,清除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 项目编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱. BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力side pulling-core forceconvert.transfer 转图guide pin 边针Tee slot cutter T 形SLOT CUTTER zigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O 形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用)air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制安全吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45 度,退刀口0 度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离)clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有高低ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 安全带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R 尺寸sprue bushing-keyed 唧嘴有管钉English Chinese program name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush 直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣根据中文词汇查所关心的技术问题，解决实际工作中的难题例如，在汉语词汇中看到——高速冲孔废料上跳（かす上り、scrap jump ）词汇，到网上一搜，中图分类号TG382.6，文章编码：1671-3508-2008-10-07-517，“高速冲压中防止冲孔废料上跳的方法”一文会告诉你引起高速冲孔废料上跳的原因，不外乎有油膜粘连、真空吸附、刃口磨损、磁性未退四个主要方面，解决这些问题有三个方向的思路可以考虑，具体手段有“毛糙面”法、“斜刀口”法、“硅胶顶出”法、“凹模刃口倒退拔”法，等等。
模具零配件中英文对照解读
常用模具零件中英文对照表2005-12-19 14:51:17 中国注塑网入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞:pipeplug锁模块：lockplate斜顶：anglefrompin斜顶杆：angleejectorrod尼龙拉勾：partinglocks活动臂：leverarm复位键、提前回杆：earlyreturnbar气阀：valves斜导边：anglepin术语：terms承压平面平衡：partingsurfacesupportbalance模排气：partinglineventing回针碰料位：returnpinandcavityinterference模总高超出啤机规格：moldbaseshuthight顶针碰运水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate. 不准用镶件：Donotuse(core/cavity)insert用铍铜做镶件：useberylliumcopperinsert初步（正式）模图设计：preliinary(final)molddesign反呵：reversecore弹弓压缩量：springcompressedlength稳定性好：goodstability,stable强度不够：insufficientrigidity均匀冷却：evencooling扣模：sticking热膨胀：theroexpansion公差：tolorance铜公(电极）：copperelectrodecompre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具encapsulation molding 低压封装成型、射出成型用模具two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location 定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块electrical discharge machining (EDM) 电火花加工electrical insulating property 电绝缘性能electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床electrochemical machine (ECM) 电解加工机床，电化学加工机床electrochemical machining (ECM) 电解加工，电化学加工electro-discharge cutting 电火花加工，电火花切割electro-discharge cutting machine 电火花切割机electro-discharge machine tool 电火花加工机床Electro-discharge Machine 电火花加工机床electro-discharge machining 电火花加工electro-discharge machining process 电火花加工工艺，电火花加工工序epoxy resin 环氧树脂guide bushing 导套guide pillar 导柱，导杆，导柱guide pin 导向销，导杆guide pin cover 导柱盖guide plate 导料板，导板guide plate blanking die 导板式冲裁模，导板式落料模guide post 导柱，导柱guide stock plate 挡料板injection mold 注射模，注塑模injection molding 注射成型，注塑成型injection-molding machine 注塑机，注射机，注塑成形机injection plunger 注射柱塞in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆inner ram 内滑块inserting molding 嵌件成形integrated manufacturing 集成制造internal stress 内应力13.intermediate platen 中间板，隔板塑料成型模具的主要设计要素脱模距stripper distance脱模斜度draft投影面积projected area最大开距maximum daylight;open daylight闭合高度mould-shut height抽芯距core-pulling distance抽芯力core-pulling force脱模力ejector force开模力mould opening force模内压力internal mould pressure;cavity pressure成型压力moulding pressure背压环back-up ring 1 bar = 14.5psi高压接头bite type fitting液压马达hydraulic motor冷却水流量计waterflow regulator打磨器材abrasive material打磨砂轮grinding wheels切割砂轮cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具piping tools高压力软管high pressure hose风管,水软管air .water hose高压油表pressure gauge压力油喉hydraulic hoses光塑检测photoelastic testing吹塑模plastic blow mould注塑模plastic injection mould冲扎复合模blank & form compound die精密冲模precision blanking die熔料流动率MFR=melt flow rate熔料流动指数MET=melt flow index推板导柱guide pin for ejector plater座板clamping plate垫块space block(plate)推板ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形distortion弯曲warp拖花drag marks火花纹EDM marks困气venting烧黑burns表面缩水shrinkage料位过薄/砸穿thin wall stock走水不平行uneven fill pattern夹水纹/流纹witness line;mismatch;stress marks 走水纹knit lines走水不齐short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴ensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (分离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的部分,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,清除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 项目编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱. BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力side pulling-core forceconvert.transfer 转图guide pin 边针Tee slot cutter T 形SLOT CUTTER zigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O 形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用)air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制安全吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45 度,退刀口0 度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离)clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有高低ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 安全带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R 尺寸sprue bushing-keyed 唧嘴有管钉English Chinese program name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush 直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣根据中文词汇查所关心的技术问题，解决实际工作中的难题例如，在汉语词汇中看到——高速冲孔废料上跳（かす上り、scrap jump ）词汇，到网上一搜，中图分类号TG382.6，文章编码：1671-3508-2008-10-07-517，“高速冲压中防止冲孔废料上跳的方法”一文会告诉你引起高速冲孔废料上跳的原因，不外乎有油膜粘连、真空吸附、刃口磨损、磁性未退四个主要方面，解决这些问题有三个方向的思路可以考虑，具体手段有“毛糙面”法、“斜刀口”法、“硅胶顶出”法、“凹模刃口倒退拔”法，等等。
（整理）常用模具零件中英文对照表
（整理）常用模具零件中英文对照表常用模具零件中英文对照表2005-12-19 14:51:17中国注塑网一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞:pipeplug锁模块：lockplate斜顶：anglefrompin斜顶杆：angleejectorrod尼龙拉勾：partinglocks活动臂：leverarm复位键、提前回杆：earlyreturnbar 气阀：valves斜导边：anglepin术语：terms承压平面平衡：partingsurfacesupportbalance模排气：partinglineventing回针碰料位：returnpinandcavityinterference模总高超出啤机规格：moldbaseshuthight顶针碰运水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate.不准用镶件：Donotuse(core/cavity)insert用铍铜做镶件：useberylliumcopperinsert初步（正式）模图设计：preliinary(final)molddesign反呵：reversecore弹弓压缩量：springcompressedlength稳定性好：goodstability,stable强度不够：insufficientrigidity均匀冷却：evencooling扣模：sticking热膨胀：theroexpansion公差：tolorance铜公(电极）：copperelectrode塑件模具相关英文词汇出处：FanE『翻译中国』作者：(转载) FanE『翻译中国』2005-12-16 20:41:59compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型、射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针零件英语punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块 air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子 ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块14. electrical discharge machining (EDM) 电火花加工15. electrical insulating property 电绝缘性能16. electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床17. electrochemical machine (ECM) 电解加工机床，电化学加工机床18. electrochemical machining (ECM) 电解加工，电化学加工19. electro-discharge cutting 电火花加工，电火花切割20. electro-discharge cutting machine 电火花切割机21. electro-discharge machine tool 电火花加工机床22. Electro-discharge Machine 电火花加工机床23. electro-discharge machining 电火花加工24. electro-discharge machining process 电火花加工工艺，电火花加工工序25. epoxy resin 环氧树脂9. guide bushing 导套10. guide pillar 导柱，导杆，导柱11. guide pin 导向销，导杆12. guide pin cover 导柱盖13. guide plate 导料板，导板14. guide plate blanking die 导板式冲裁模，导板式落料模15. guide post 导柱，导柱16. guide stock plate 挡料板4. injection mold 注射模，注塑模5. injection molding 注射成型，注塑成型6. injection-molding machine 注塑机，注射机，注塑成形机7. injection plunger 注射柱塞8. in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆9. inner ram 内滑块10. inserting molding 嵌件成形11. integrated manufacturing 集成制造12. internal stress 内应力13. intermediate platen 中间板，隔板塑料成型模具的主要设计要素脱模距stripper distance脱模斜度draft投影面积projected area最大开距maximum daylight;open daylight闭合高度mould-shut height抽芯距core-pulling distance抽芯力core-pulling force脱模力ejector force开模力mould opening force模内压力internal mould pressure;cavity pressure成型压力moulding pressure背压环back-up ring1 bar = 14.5psi高压接头bite type fitting液压马达hydraulic motor冷却水流量计waterflow regulator打磨器材abrasive material打磨砂轮grinding wheels切割砂轮cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps小五金工具piping tools高压力软管high pressure hose风管,水软管air .water hose高压油表pressure gauge压力油喉hydraulic hoses光塑检测photoelastic testing吹塑模plastic blow mould注塑模plastic injection mould冲扎复合模blank & form compound die精密冲模precision blanking die熔料流动率MFR=melt flow rate熔料流动指数MET=melt flow index推板导柱guide pin for ejector plater座板clamping plate垫块space block(plate)推板ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形distortion弯曲warp拖花drag marks火花纹EDM marks困气venting烧黑burns表面缩水shrinkage料位过薄/砸穿thin wall stock走水不平行uneven fill pattern夹水纹/流纹witness line;mismatch;stress marks 走水纹knit lines走水不齐short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴tensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (分离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的部分,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,清除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 项目编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱.BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力side pulling-core forceconvert.transfer 转图guide pin 边针Tee slot cutter T形SLOT CUTTERzigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cyclecounter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用) air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制安全吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45度,退刀口0度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙)set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离) clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有高低ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 安全带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R尺寸sprue bushing-keyed 唧嘴有管钉English Chineseprogram name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth 正侧双用镶钻石钢锣刀end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层。
HASCO模具配件中英文对照表
HASCO Z 标准件系列Z00 导柱Guide pillar Z01 导柱Guide pillar Z011 导柱Guide pillar Z012 导柱Guide pillar Z013 导柱Guide pillar Z014 导柱Guide pillar Z0141 导柱连接端End piece Z0142 导柱连接端End piece Z015 导柱Guide pillarZ0151 导柱连接端（…专用）Pillar adapterZ0152 导柱连接端Pillar adapterZ02 顶杆Ejector rodZ022 导管Guide sleeveZ03 导柱Guide pillarZ05 圆锥形管精定位Locating unit, round Z055 圆形垫片SpacerZ056 圆形垫件SpacerZ06 平锥形导块Locating unitZ07 长方形导块Square guide barZ08 直身方形管位导块Pre-centering unitZ081 方形垫片Spacer discZ091 方形定位锁块Square interlockZ092 方形定位锁块母Square interlockZ093 方形定位锁块母Square interlockZ10 导套Guide bushZ10W 自润滑导套Guide bushZ11 导套Guide bushZ11W 自润滑导套Guide bushZ12 滚珠导套Ball guide bushZ13W 自润滑导套Self lubricate. Guide bush Z15W 自润滑垫片Self lubricate. Flat stock Z16W 自润滑垫片Self lubricate. Guide rail Z17 长方形导块（Z07/... 专用）Guide retainerZ20 定板导套Centering sleeveZ25 定位销Dowel pinZ26 定位销Dowel pinZ28 六角螺母Hexagon nutZ281 六角螺母Hexagon nutZ282 六角螺母Hexagon nutZ285 螺母Nut for T-slotsHASCO Z 标准件系列Z286 螺母Nut for T-slotsZ30 胚头六角螺丝Socket head cap screwZ31 胚头六角螺丝Socket head cap screwZ32 薄胚头六角螺丝Socket head cap screwZ33 薄胚头六角螺丝Countersunk screwZ34 六角螺丝Hexagon socket set screw Z35 六角螺丝Hexagon socket set screw Z351 六角螺丝Hexagon socket set screw Z352 螺丝杆Locking screwZ36 弹簧滚珠螺丝Spring plungerZ361 弹簧滚珠螺丝Spring plungerZ37 弹簧滚珠螺丝Spring plungerZ370 弹簧定位螺丝Spring plungerZ371 弹簧滚珠螺丝Spring plungerZ372 弹簧定位螺丝Spring plungerZ3721 弹簧定位螺丝Spring plungerZ373 弹簧定位镶件Spring plungerZ374 弹簧滚珠镶件Spring plungerZ375 弹簧滚珠镶件Spring plungerZ38 限位螺丝Shoulder screwZ381 螺丝Slotted shoulder screwZ39 螺丝Slotted shoulder screwZ40 顶针（全硬）Ejector pinZ41 顶针（表层硬）Ejector pinZ42 顶头顶针（全硬）Ejector pinZ43 顶头顶针（表层硬）Ejector pinZ44 有托顶针（表层硬）Shouldered ejector pinZ441 有托顶针（全硬）Shouldered ejector pinZ442/.../S 有托顶针（定制件）Ejector pinZ45 司筒（表层硬）Ejector sleeveZ451 司筒（全硬）Ejector sleeveZ4501 司筒（全硬）Ejector sleeveZ452/…/S 司筒（定制件）Ejector sleeveZ453/ …/S 司筒（定制件）Ejector sleeveZ454/…/S 司筒（定制件）Ejector sleeveZ455/…/S 司筒（定制件）Ejector sleeveZ456 顶针耐磨镶件Wear sleeveZ456/ …/S 顶针耐磨镶件（定制件）Wear sleeveZ46 扁顶针（表层硬）Flat ejector pinZ461 特殊扁顶针Special flat ejectorZ462 特殊扁顶针镶件（Z461/ …专用）GuideZ465 扁顶针（全硬）Flat ejector pinZ466/…/S 扁顶（定制件）Flat ejector pinZ47 顶针延长杆Extension rodZ48 年月标记镶件Date insertZ4800 标记镶件Marking insertZ4801 更新标记镶件Renew insertZ481 更新年份镶件Year insertZ482 月份标记镶件Month insertZ483 年份标记镶件Year insertZ484 箭头标记镶件Arrow insertZ485 年月标记镶件Date insertZ4851 更新年份镶件Year insertZ4861/1 塑料标记镶件Resin marking insert Z4861/2 班别标记镶件Shift marking insert Z4861/3 日期标记镶件Day marking insert Z4861/4 月份标记镶件Month-marking insert Z4861/5 年份标记镶件Year-marking insert Z4863 年月日标记镶件Multi. Marking insert Z4864 年月日塑料标记镶件Multi. Marking insert Z487/1 “回收标记”嵌件Recycling insertZ487/2 “回收标记”嵌件Recycling insertZ487/3 “回收标记”嵌件Recycling insertZ488 CE 标记镶件CE marking insertZ489 食物标记镶件Food marking insert Z49 模芯镶件Core pinZ491 气动顶出阀Air valveZ492 模芯镶件Core pinZ495 喷气块Blow off stripZ4951 喷气咀Blow off nozzleZ50 唧咀Sprue bushingZ51 唧咀Sprue bushingZ511 唧咀Sprue bushingZ512 唧咀Sprue bushingZ515 气动唧咀Pneumatic nozzleZ516 细水口镶件Nozzle insertZ518 唧咀Sprue bushingZ519 唧咀Sprue bushingZ53 扣水口镶件Sprue pullerZ55 顶针板园垫件Stop pinZ551 顶针板园垫件Stop pinZ56 环子Head for ejector rod Z561 环子Head for ejector rod Z562 介子WasherZ57 园形垫件Support pillarZ571 园形垫件Support pillarZ60 园线弹簧Compression spring Z601 园线弹簧Compression spring Z62 蝶形弹簧Disc springZ64 方线弹簧Compression spring Z65 扁线弹簧Compression spring Z67 弹弓介子环Retaining ringZ671 弹弓介子钳Mounting pliersZ68 弹弓介子环Retaining ringZ681 弹弓介子钳Mounting pliersZ69 螺丝介子Spring washerZ691 螺丝介子Spring washerZ70 吊架连吊环Lifting deviceZ701 调距螺栓Distance boltZ71 吊环Eye boltZ711 吊环Eye boltZ712 吊环Eye boltZ72 吊环Eye boltZ73 安全扣Tool safety device Z741 固定玛夹Power clampZ7411 空板架Spacer blockZ7412 空板架Spacer blockZ742 固定玛夹Power clampZ743 固定玛夹Power clampZ75 固定玛夹Clamp systemZ751 T头螺丝T head boltZ752 T头螺丝T head boltZ7521 T 头螺丝T head boltZ7522 T 头螺丝T head boltZ753 介子环Spherical washerZ754 介子环Conical seat washer Z755 介子环Conical seat washer Z76 快速玛夹模装置Quick clamping jig Z761 快速玛夹模板Clamping plateZ762 玛夹导柱Clamping boltZ763 玛夹锁钉Eccentric boltZ765 离合锁（套）Locking housingZ766 离合锁（插）Locking plugZ80 带阀快接喉套Shut-off couplingZ80/…/45 带阀快接喉套Shut-off couplingZ80/…/90 带阀快接喉套Shut-off couplingZ801 快接喉套CouplingZ801/…/45 快接喉套CouplingZ801/…/90 快接喉套CouplingZ805 带阀侨式快接喉套Diverting coupling Z8051 侨式快接喉套Diverting coupling Z807 带阀快接喉套Shut-off couplingZ807/…/45 带阀快接喉套Shut-off couplingZ807/ •/90 带阀快接喉套Shut-off couplingZ808 快接喉套CouplingZ809 带阀快接喉套Multi. shut-off coupling Z81 快接喉咀NippleZ81/…/90 喉嘴NippleZ811 带阀快接喉咀Shut-off nippleZ812 适配连接头Double sided connector Z814 适配连接头AdapterZ815 适配连接头AdapterZ817 喉咀Hose nippleZ819 带阀快接喉咀Multi. shut-off nippleZ82 带阀快接喉套Shut-off couplingZ83 喉咀Hose connectorZ831 快接喉套Plug-in connectorZ84 PVC喉管PVC-HoseZ85 PVC喉管PVC-HoseZ851 PVC喉管PVC-HoseZ853 耐高温喉管Viton-HoseZ854 耐高温喉管Teflon-HoseZ855 耐高温喉管Corrugated metal hose Z86 喉箍Hose clipZ861 紧夹用喉箍Crimping sleeveZ865 紧夹用喉钳Crimping toolZ87 喉咀Hose nippleZ875 喉咀Hose nippleZ876 喉咀Hose nippleZ876/ -/45 喉咀Hose nippleZ876/ -/90 喉咀Hose nippleZ877 连接头Joining pieceZ878 转曲连接头ConnectorZ88 喉咀Hose nippleZ89 喉咀Hose nippleZ90 加长快接喉咀Extension nippleZ905 适配连接头AdapterZ906 延长管Extension tubeZ91 加长喉咀Extension tubeZ93 密封胶布Sealing tape (Teflon) Z94 喉塞Tapered plugZ941 喉塞Tapered plugZ942 膨胀喉塞Sealing plugZ945/1 套装拉胀喉塞工具Assembly-setZ945/2 套装拉胀喉塞工具Assembly-setZ947/1 拉胀工具延长杆Extended scale tube Z947/2 拉胀工具延长杆Extended scale tubeZ95 钢管Brass tubeZ96 运水铝质螺旋芯（单）Spiral coreZ961 运水铝质螺旋芯（双）Spiral coreZ962 运水针Junction tubeZ964 运水回路胶环（小）Diverting elementZ9641 运水回路胶环（大）Diverting elementZ965 运水胶隔片Plug baffleZ967 隔水片Baffle coreZ968 运水胶质螺旋芯Spiral coreZ969 运水胶质螺旋芯Spiral coreZ97 运水针Cascade water junction Z975 特快导热针Heat pipeZ98 耐高温密封胶圈O-RingZ1001 阀针Needle valveZ101 电热喷咀Hot nozzleZ101G 电热喷咀Hot nozzleZ101R 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ1011 电热喷咀胆Inner part of nozzleZ1011M 电热喷咀胆Inner part of nozzleZ1015 金属密封圈Metal O-RingZ103 电热喷咀Hot nozzleZ103G 电热喷咀Hot nozzleZ103R 电热喷咀Hot nozzleZ1031 电热喷胆胆Inner part of nozzleZ103T 电热喷咀Hot nozzleZ103GT 电热喷咀Hot nozzleZ103RT 电热喷咀Hot nozzleZ1031T 电热喷胆胆Inner part of nozzleZ103M 电热喷咀Multiple gate nozzleZ1031M 电热喷胆胆Inner part of nozzleZ10320 电热喷咀Muitlple gate nozzleZ10370 电热喷咀Muitlple gate nozzleZ104 电热喷咀Hot nozzleZ104G 电热喷咀Hot nozzleZ104R 电热喷咀Hot nozzleZ1041 电热喷胆胆Inner part of nozzleZ104E 电热喷咀Hot nozzleZ104GE 电热喷咀Hot nozzleZ1041E 电热喷胆胆Inner part of nozzleZ104GV 电热喷咀Hot nozzleZ1041V 电热喷咀胆Inner part of nozzleZ10420 电热喷咀Muitlple gate nozzleZ1052 圆形隔热垫件Distance ringZ1055 炉头接驳衬套Sprue bushingZ106 热流道板ManifoldZ10600 热流道板ManifoldZ1061 密封塞钉PlugZ1062 密封圈Sealing washerZ1063 六角螺丝Hexagon head screwZ1064 保温铝板Reflector sheetZ1067 套装零件Accessory kitZ107 气动针阀Needle valveZ1072 针阀司套Needle guide sleeveZ1073 针阀司套Needle guide sleeveZ1076 圆形隔热垫环Distance ringZ109 过滤器Filter cartridgeZ1095 过滤器Filter cartridgeZ110 发热棒Cartridge heaterZ111 发热棒Cartridge heaterZ1133 发热环Heater bandZ1134 发热环Heater bandZ1138 发热管（可弯曲）Fiexble heaterZ116 套装接线工具Assembly setZ1161 耐高温电线Extension cableZ1162 线耳Crimp type bracketZ1164 耐高温电线Extension cableZ1165 连接管Butt jointZ1166 线耳Cable end sleeveZ1167 套件Assembly kitZ1168 热电偶线Signal cableZ121 隔热板（洞、无洞）Insulating sheetZ1211 隔热板（洞、无洞）Thermal insulating sheet Z122 电热温控器Temperature controllerZ1221 温控器组件ModuleZ1224 插座嵌件Socket insertZ1225 温控器连接线Connection power/signalcableZ1226 温控器连接线（转换用）AdapterZ1227 插座ScoketZ1228 插座ScoketZ1229 插座嵌件InsertZ123 多组温控器Multi zone control system Z125 温控器Temperature controllerZ126/1 温控器Temperature controllerZ126/2 温控器Temperature controllerZ1261 温控器ModuleZ1262 盖板Cover PlateZ127 插头PlugZ128 插头CouplingZ1292 多组温控器系统Multi zone control unitZ1295 热电偶ThermocoupleZ1295/1 热电偶ThermocoupleZ1295/3 热电偶ThermocoupleZ1295/5 热电偶ThermocoupleZ1296 电热固定座Coupling nippleZ1297 电热固定座Fastening nippleZ131 接线盒Wiring boxZ1312 隔热板Thermal insulating sheetZ1370 压力感应器Pressure transducerZ1371 压力感应器Measuring tongueZ1372 压力感应器Measuring measuring tongue Z1373 压力感应器Force transducerZ1381 连接线Connection cableZ1382 连接线Connection cableZ1383 连接线Connection cableZ1384/1 放大器（压-电）Charge amplifierZ1385/2 数据转换器Data converterZ1387 连接线Connection cableZ1391 替代插件DummyZ1392 固定支架BracketZ1393 替代插件DummyZ1394 固定支架BracketZ1395 固定支架Mounting plateZ1396 安装导管Spacer tubeZ1397 安装导套Mounting nutZ1398 安装导杆Tubular wrenchZ1399 安装导杆Insertion toolZ140 磁感应限位开关Limit switchZ1401 连接线Connection cableZ1402 连接线Connection cableZ141 测试表TesterZ145 红外线物体探测器Infrared control unitZ1451 红外线发送器Infrared transmitterZ1452 红外线接收器Infrared receiverZ1453 红外线发送器Infrared transmitterZ1454 红外线接收器Infrared receiverZ1455 固定支架BracketZ1457 接线盒Wiring boxZ1458 连接线Connection cableZ1460 隔热板Thermal insulating sheetZ1471 Z1473 Z1475 Z1500 感应开关器感应开关器感应开关器来福线丝杆（L/左、R/右）Inductive proximity switchInductive proximity switchInductive proximity switchHelical spindleZ1520 来福线丝套（L/左、R/右）Helical nutZ1540 齿条RackZ1550 带齿轮圆模芯Geared-spindle coreZ1552 螺母铜司（原料）Pilot threat bush blankZ1553 齿轮Gear wheelZ1555 齿轮Gear wheelZ1558 平键Parallel keyZ1560 圆锥滚柱轴承Roller bearingZ1562 滚珠轴承Ball bearingZ1564 滚柱压珠轴承Needle-thrust ball bearing Z1565 耐磨轴承环Thrust ringZ1566 滚柱压柱轴承Needle-thrust roller bearing Z159 顶杆连接装置Ejector coupling deviceZ1591 连接头Coupling spigotZ1592 长接头coupling rodZ163 复位衬套Pressure sleeveZ164 复位导套BushZ165 顶板复位装置Pull back deviceZ166 复位顶出杆Ejector rodZ167 法兰盘Locking flangeZ168 快速联接装置Rapid couplingZ1681 联接杆Ejector rodZ1682 联接杆Ejector rodZ169 二级顶出装置Two-stage ejectorZ1695 二级顶出装置Two-stage ejectorZ1696 适配器AdapterZ170 程序模板开合装置Latch locking unitZ171 程序模板开合装置Latch locking unitZ172 模板开合胶塞（涨钉）Frictional pullerZ1721 模板开合胶塞（涨钉）Frictional pullerZ173 程序模板开合装置Round latch locking unitZ1731 程序模板开合拉杆Pulling rodZ1732 拉杆衬套Threaded bushZ174 程序模板开合装置Latch locking unitZ1751 斜齿条RackZ1752 斜齿条RackZ1754 斜齿条滑动方铁Guide blockZ1755 斜齿条固定方块Mounting blockZ1756 方铁Spacer blockZ1761 双面斜齿条PackZ1764 斜齿条滑动方铁Guide blockZ180 滑块SlideZ181 滑块组件Mould slide unitZ1810 锁定块Locking heelZ182 锁定块Locking heelZ1821 耐磨垫板Wear plateZ183 锁定块Duble locking heelZ1831 防磨垫板Wear plateZ1832 防磨垫板Wear plateZ185 滑块管导块Guide stripZ185W 自润滑块管导块Self lubric.Guide stripZ186W 自润滑垫板Self lubric.Flat stockZ187 斜导柱固定导套RetainerZ200 热喷嘴Hot nozzleZ2300 正向锁定液压缸Positive locking cylinderZ2310 固定块FlangeZ2320 适配器AdapterZ2330 适配器螺丝Pressure screwZ240 气动阀式开闭控制器Pneumatic control unitZ2401 摇臂式阀Rocker arm valveZ2411 油水分离器Lubro-control unitZ2412 油水分离器Lubro-control unitZ2416 消音塞SilencerZ251/2 测温表Temperature deviceZ2511 测温针Temperature feelerZ2512 测温针Temperature feelerZ2515 测温针Temperature feelerZ252 测温表Pocket temp.measuring deviceZ255 精度量度针规Inspection pin setZ256 针规钳Inspection pin holderZ257 精密薄垫片Gauge shim stockZ260 耐温润滑油Heavy duty lubricantZ261 耐温润滑喷剂Heavy duty lubricantZ262 防锈喷剂Heavy duty lubricantZ263 清洁喷剂Multi purpose cleaner sprayZ264 矽质离模剂Silicone sprayZ265 脱模剂Release agentZ266 发热棒安装用喷剂Special assembly sprayZ267 除锈喷剂Rust solventZ268 特效润滑喷剂Teflon-lubricating sprayZ269 表面防护剂Surface protectionZ3307 注孔衬套镶件Chamber insertZ3308 密封套环Sealing ringZ3309 承托套管Spacer sieeveZ3310 电热喷咀Hot nozzleZ3340 电热喷咀Hot nozzleZ3360 电热喷咀Hot nozzleZ33201 电热喷咀Hot nozzleZ33202 电热喷咀Hot nozzleZ3500 电热喷咀Hot nozzleZ3501 电热喷咀Hot nozzleZ3510 喷咀镶件Nozzle Tip,3-hole type Z3512 喷咀镶件Nozzle Tip,1-hole type Z3520 喷咀镶件Nozzle Tip,3-hole type Z3522 喷咀镶件Nozzle Tip,1-hole type Z3550 喷咀主体Nozzle bodyZ3351 发热套HeaterZ3352 热电偶Thermo coupleZ3353 分隔帽（防止塑料滞留）Insulator capZ3554 密封环套Sealing ringZ3555 垫环Spacer discZ3556 承托套管Spacer sleeveZ3560 注孔衬套镶件Melt chamber insertZ3561 注孔衬套镶件Melt chamber insertZ3580 发热套拆卸工具Dismantling toolZ3581 六角套筒Box spannerZ3600 推缩模芯Collapslble coreZ6007 不锈钢快接喉套CouplingZ6015 不锈钢快接喉套CouplingZ6025 不锈钢快接喉套CouplingZ6055 不锈钢快接喉套CouplingZ6065 不锈钢快接喉套CouplingZ6075 不锈钢快接喉套CouplingZ6107 不锈钢带阀喉套CouplingZ6115 不锈钢带阀喉套CouplingZ6125 不锈钢带阀喉套CouplingZ6155 不锈钢带阀喉套CouplingZ6165 不锈钢带阀喉套CouplingZ6175 不锈钢带阀喉套CouplingZ6302 不锈钢快接喉套NippleZ6303 不锈钢快接喉套NippleZ6305 不锈钢加长喉咀Extended nippleZ6340 不锈钢加长喉咀Extended nippleZ6353 不锈钢带阀喉咀NippleZ6505 不锈钢喉咀Hose connectorK100 固定环Location ringK103 固定环Location ringK500 固定环Location ringK503 固定环Location ringK505 固定环Location ringA1255 洗石笔Trueing diamondA1265 Dressind stoneA1910 Cutting wheelA1915 Special grinding wheelA1930 Diamond cutting wheelA1931 Boronnitrid cutting wheel A1935 Diamond grinding wheel A1936 Boronnitrid grinding wheel A2500 锥形钻咀Tapered drillA2600 锥形镰靶Tapered reamerA2700 沉头锣刀Counter boreA2710 密封圈用坑槽锣刀Circular groove cutterA2715 固定钉Guide spigotA2720 沉头锣刀Special counter boreA2800 螺丝牙攻Tap setA3500 长方形电蚀铜料EDM copperA3501 长方形电蚀铜料EDM copperA3502 园方形电蚀铜料EDM copperA3503 园方形电蚀铜料EDM copperA3504 园方形电蚀铜料EDM copperA3510 长方形电蚀石墨料EDM GraphiteA3511 园方形电蚀石墨料EDM GraphiteA3514 长方形电蚀石墨料EDM GraphiteA3515 园方形电蚀石墨料EDM GraphiteA3541 回收再造标记石墨工Graphite electrodeA3542 回收再造标记石墨工Graphite electrodeA3543 回收再造标记石墨工Graphite electrodeA3545 CE标记铜工CE marking electrodeA3546 食品标记铜工Food marking electrode A3547 回收再造标记铜工Recyc.Marking electrode A4700 套装气喷枪Airblow kitA4720 气喉管Spiral hoseA5000 撞激拉出工具Extraction tool kitA5050 六角匙Hexagon keyA5051 六角匙Hexagon keyA5053 六角匙Hexagon key with pilotA5055 六角匙Hexagon keyA5060 套装六角匙Hexagon key setA5061 套装六角匙Hexagon key setA5080 Slotted nut driver■TTI◎3-Plate小水口 D & E STANDARD」T-pputLHcileferSucitaet WP Cap $or«wA5120 A5121 A5130 A5710 A5712 A5714 A5716 A5720 A5722 A5723 H1050 H1060 H5050 T4010 T4020 T4030 T4040超囲)atMOtr ftioct [SB)顶*i ■板 A E K <I BF HttalnBF PL I 1E顶针板 B ElCClor Pk>tc 內■"— 下固定板Gbmpm.門厲匸門Ratuwn Ph (RPhi 反推杆扳手 扳手 六角套筒 开合计数器 可重置开合计数器 双合式计数器 复合式计数器 护帜 重置器塑质固定框架 铝质固定框架 蕉形浇口镶件 蕉形浇口镶件 过滤器 绿色扁线弹簧 蓝色扁线弹簧 红色扁线弹簧 黄色扁线弹簧2-Plate 大水口Sickle spa nner Pin wrench Box spa nner Cycle coun ter Cycle counter,resetabie Combi nedcycle counter Uni Resetti ng tools In sulati ng frame In sulati ng frame Gate in sert Gate in sert Filter cartridge Compressi on spri ng Compressi on spri ng Compressi on spri ngCompressi on spri S STANDARD上 Hl 定按 Tfip ClampirG Pt.ta (TCP) 定模板*瓠皿址心| 脱料裱 Sir ppcrPl-rafSP) 动棋扳匚川円士眾扳帥卯t PlilO (IP} {au de 3k.m ATypE导套 Guhde Q uah aType {GEB ■卜頁导轻Sip:k i ； | J| Sorcw [GS)无头固定載丝 ==l^ulde p ifl 悝戸対导柱3-TYPEGuide Pin Swkel ND承板 Support Plato (IP) 模脚 Spm ・r BlKk(SB) 顶*i 咗& A Ejector Retainer Piite (EA) 顶板 B Elector Plate (EB) 下固定板BdMdm Clamp ：n® Plate (BCP)-pGude &u«h Bl Type (&BB)直导套 I-Grub So raw (朋> 无头固定螺丝—Quide Buth A Type (OBA)导套上固定板 Top Clamping Plate (TCP) 卸料板 Runner Stripper Plate (RSP) 定-tSfc Cavity PH1e (CA) 脱料板 Stopper Plate(SP) 动模板 Co” Plate (CB) Support P1»to (IP) 拉杆导柱SuppoH Pm (SPM) 模脚 Sp ・oa Block (SB) 顶針咗A Ejector Rotainer Plate (EA) 顶针板 B Elector Plate (EB) Guid, But!) A Type (GBA)导套 BiKhB Type (GBB)酉导窘Grub Screw (GS)无头固定螺丝Guide Pin (GPA 》导柱下固Clamping Pl ・to (BCP)- itReturn Pin（胪⑷反推杆IB I rside Guide Pin i ・ oultido Guido Pin Support PinGuldr ButhGuide PinGuido BushSocket HD Cap Seraw3-Plate 小水口F &G STANDARD卜固定tS 丫“ Clamping Plale (TCP) 卸#斗板 Runner Stripper Plate (RSP) 定模板C •计Pl«t« (CA) 动模板 Core Plato (CB) __________________ “ -Support Pin (SPN> 拉杆导柱 —Return Pin伸叭)反推杆。
模具零件标准名称中英文对照表
模具零件标准名称中英文对照表1 顶针E.P. 88 拉杆suppor pin2 有托顶针stepped E.P. 89 拉杆定位介子support pin spacer3 扁顶针rectangular E.P. 90 齿轮gear4 司筒E.P. sleeve 91 丝杆screw5 中心针center Pin 92 轴承bearing6 直身导边straight leader Pin 93 油缸oil cylinder7 直身杯司straight bushing 94 气缸air cylinder8 有托导边shoulder leader Pin 95 间隔圈spacer ring9 有托杯司shoulder bushing 96 垃圾钉stopper ring10 方定位块position block set 97 撑头support pillar11 定位锥taper pin set 98 行位开关组detection switch set12 尼龙塞parting lock 99 撑脚distance spacer13 中托司套ejector lead bushing 100 上模cavity14 中托导柱ejector leader pin 101 上模镶件cavity insert15 脱水口螺丝组puller bolt set 102 上模镶针inlay cavity pin16 限位螺丝stopper bolt 103 潜水镶套pin point gate buyshing17 限位钉positioning pin 104 流道衬板runner plate18 管位块slotter key 105 水口扣针runer lock pin19 弹簧spring 106 行位slider20 螺钉screw 107 行位导向键slider certer rail21 限位块distance spacer 108 行位镶件slider insert22 无头螺丝screw plug 109 斜边angular pin23 平头螺丝socket head cap screw 110 方斜边angular cam24 波子螺丝ball plunger 111 铲鸡locking block25 定位螺钉positioning screw plug 112 行位压板slider guide rail26 胶圈o ring 113 隔热板insulation sheet27 喉塞taper screw plug 114 压板(其他类) holding plate28 法兰locating ring 115 楔块spacer wedge29 唧嘴sprue bushing 116 销钉dowelpin30 截流塞cooling circuit plug 117 下模core31 上固定板top clamping plate 118 下模呵block core32 脱料板runner stripper plate 119 下模镶件core insert33 上模板cavity plate 120 下模镶针core pin34 推板stripper plate 121 拉板tension link35 下模板core plate 122 拉板介子tension link retainer36 支承板support plate 123 行位垫块slide plate37 间隔板spacer block 124 斜边压块holding plate for A.P.38 顶针板1 ejector retainer plate 125 斜顶loose core39 顶针板2 ejector plate 126 斜顶滑座slide unit for loose core40 顶针板3 ejector plate 127 冷胶套sprue lock bushing41 顶针板4 ejector plate 128 运水镶件insert for cooling42 下固定板botton clamping plate 129 等高螺钉stopper bolt43 回针return pin44 二板模2-plate mold 130 缩o哥return core45 三板模3-plate mold 131 扣鸡(尼龙拉勾) nylon latch lock46 中托司shoulder guide bushing 132 排气槽venting47 中托边guide pin 133 浇口gate48 顶针板ejector retainer plate 134 唧嘴口径sprue diameter49 底针板ejector support plate 135 浇注系统feed system50 托板support plate 136 浇口大小gate size51 管钉dowel pin 137 直接浇口direct gate52 导柱guide jpillars 138 环形浇口ring gate53 导套guide bushes 139 点浇口pin-point gate54 拉料杆sprue puller 140 侧浇口edge gate55 圆锥头拉料杆sprue puller, conical headed 141 盘形浇口disk gate56 分流道拉料杆runner puller 142 潜伏浇口submarine gate57 枯杆kicker pin 143 扇形浇口fam gate58 复位杆ejector plate return pin 144 护耳浇口tab gate59 导板guide plate 145 大小口edge gate60 滑板slicde plate 146 细水口pin-point gate61 耐磨板wear plate 147 转水口switching runner gate62 垫板backing plate 148 流道runner puller63 固定板retainer plate 149 主流道sprue64 支承板backing plate 150 分流道runner puller65 定位板locating plate 151 热流道hot runner66 推件固定板ejector retainer plate 152 梯形流道trapezoidal unner67 支承柱support pillar 153 圆形流道round runner68 支架ejector housing 154 热嘴hot sprue69 斜导柱angle pin 155 热流道板hot manifold70 行位slide 156 发热管cartridge heater71 斜鸡wedge 157 控针thermocouples72 弯销dog-leg cam 158 插头connector plug73 斜滑块angled-lift splits 159 插座connector socket74 定位圈locating ring 160 运水water line75 限位块stop block 161 喉管tube76 推块ejector pad 162 塑胶管plastic tube77 推件板stripper plate 163 快速接头jiffy quick connector socket78 定位销locating pin 164 收缩率shringkage79 垫块spacer 165 注射压力injection pressure80 型腔cavity 166 成形压力moulding pressure81 活动镶件movable insert 167 弯曲力bending force82 镶件insert 168 拉伸力drawing force83 型芯core 169 锁模力clamping force84 侧型芯side core 170 开模力mould opening force85 螺纹型芯threaded core 171 脱模力ejection force86 开模槽plybar slot 172 抽芯力core-pulling87 内模管位inter-lock 173 抽芯距core-pulling distance。
模具外贸人员专用：模具中英文对照
模具外贸人员专用：模具中英文对照局部视图 Partial View冷料# Cold Slag线切割 Wire E.D.M轮廊 Contour螺纹孔 TappingHole连接件 Fittings斜针 Angle Pin接合 Engage替换镶件InterchangeableMold Inserts指定吨位的注塑机 Specific Press水嘴接头 Water Fittings螺纹 Eyebolt Thread回针 Stop Pin二级顶出针 Sub-LeaderdPin镶件 Mold Insert加硬 Harden唧嘴 Sprue设计筒图 Design Preliminary名称块表 Title Block版本标识 Revision Level材料清单 Stock List制模 Build Mold手动滑块 HandSlide漏水测试 Leak Test流道排气 Runner Vents抛光 Draw Polish侧抽芯 SideAction加强筋 Reinforcing三角撑 Gusset柱子 Bossed出模斜度 Draft外廊 Contour落单会议 Kick-Off Meeting 装卸孔 Handling Hole运输安全带 Moldstrap码模槽 ClampSlot撑头 Support Pillar螺牙1/2-13 EyeBolt 1/2-13Tap 导柱位 LeaderPin Location耐落胶 TeflonPaste偏移量 Offset水塞 Water Line Plug撬模脚 PpySlot重新加工 Reworked配件 Components补偿 Compensation平面度 Parallel倒角 Chamfer模胚 Mold Base热嘴 Hotnozzle火花机 Edm熔接线 Weildline压机 Press晒纹 Texturing梯形 Trapezoid凸缘?法兰 Flange方铁 Spacer Block顶针板 Ejector Plate顶针底板 Ejector Retainer Plate垫板 Retainer Plate后模镶针 Core Pin拉圾钉 Stop Pin有托顶针 Shoulder Ejector Pin顶针板导套 GuidedEjection Bushing针板导柱 Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴ExtensionNozzle Bushing 水口板导套 RunnerStripper Plate Bushing 定位圈(法兰) LocatingRing管钉(定位销) DowelPin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet Valve截水口镶件 RunnerShut-Off Insert早回 Early Ejector Return加速项 Accelerated Ejector客户 Client产品名 Part Name产品编号 Part No缩水 Shrinkage版本 Rev模胚 Mold Base下模镶件 Core Block上模镶件 Cavity Block小镶件 Sub-Insert下模小镶件 CoreSub-Insert上模小镶件 CavitySub-Insert行位 Slide行位镶件 Slide Insert压条 Gib压紧块(铲机) Jaw硬片(摩擦片) WearPlate水口铁 RunnerBar上模水口铁 UpperRunner Bar下模水口铁 LowerRunner Bar弹簧 Spring水口勾针 Sprue Puller Pin顶针 Ejector Pin撑头 Support Pillar直身锁 SideLock斜度锁 Interlock锁模板 SafetyBar‘O’令(密封圈) O'Ring喉塞 Plug隔水片 Baffle波子螺丝(行位定位螺丝) Ball-Catch 斜顶 Lifter控制开关 Switch回针 Return Pin斜导柱 Angle Pin推板 Stripper Plate方铁(垫铁)Spacer Block顶针板 Ejector Plate顶针底板 Ejector Retainer Plate 垫板 Retainer Plate垃圾钉 Stop Pin有托顶针 Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱 Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴ExtensionNozzle Bushing 水口板导套 RunnerStripper Plate Bushing 定位圈(法兰) LocatingRing管钉(定位销) DowelPin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet Valve截水口镶件 RunnerShut-Off Insert早回 Early Ejector Return加速顶 Accelerated Ejector扁顶 Blade出模斜波 Draft手动滑块模具 Hand Slide-In Type Mold 回针板 Backup合模 Shutoff空隙槽 ClearanceSlot导柱及导套 LeaderPin Bushing水口拉钩 Spuer Puller模框镶件 Pocket Insert成型热固性塑胶模具 ThermosetMold三板模 3-PlatMold分型面 PartingLine司筒 Ejector Sleeve垫圈 Washer熔接线(夹水纹) Weldline吸针 Sucker Pin回针板 RetainerPlate顶出板 Knock-Out Plate电动安全开关Electrical-SafetySwitch 脱开 Cut Of Position预先决定 Preload缓冲器 Bumper衬垫 Cushion公差 Tolerance突然性动作 Slam销针 Dowel钩槽 Gib精磨 Finished通框 Through Window粘后模 StickingCore粘水口 StickingSprue夹水纹 Weld Line变形 Warpage走水不平均 Filling Uneven走不齐 Short Shot挂成品 Part Hanging漏水 Water Leakage刮花(擦伤) Galling漏电 Ele Leakage困气 Air Trapping温度 Temperature注塑模 Injection Mold入水 Gate试板 Sampling倒圆 Fillet顶棍 Ejector顶白 Stress Mark粘前模 Sticking Cav名称块表 Title Block版本标识 Revision Level材料清单 Stock List斜导柱(斜边) AnglePinA板 A'plateB板 B'plate倒扣 Under-Cut披峰 Flash缩水 SinkMark氮化 Nitride不规则四边形Trapezoid缩水 Shrinkage连续的 Consecutive雕刻 Engrave出模角 Draft分模面 Parting Surface擦位 Shut-Off(S/0)导套 Bushing回针 Return Pin加硬 Harden唧嘴 Sprue设计筒图 Design Preliminary 丝印 Silkprint不干胶 Adhesive Sticker导向针 Guide Din线切割 Wire-Cut电火花 Edm抛光 Polishing蚀纹 Texture探热针 Thermocouple三打螺丝毫(限螺丝) Stripper Bolt盖板 Cover Plate齿轮 Gear油唧 Hydraulic Cylinder司筒 Ejector Sleeve导柱 Leader Pin冷料# Cold Slag线切割 Wire E.D.M.轮廓 Contour螺纹孔 Tapping Hole连接件 Fittings斜针 Angle Pin接合 Engage替换镶件 Interchangeable Mold Inserts 指定吨位的注塑机 Specific Press水嘴接头 Water Fittings螺纹 Eyebolt Thread回针 Stop Pin二级顶出针 Sub-LeaderPin镶件 Mold Insert锁定位 Lock楔子(铲鸡) Wedge高产量模量 HighVolume Running Mold 剖面图 Cross Section模具结构 Mold Construction 模芯 Parting Core局部视图 Partial View热流道 Manifold热嘴 Hot Nozzle型腔数 Cav No模号 Mold No胶料 Material尺寸 Dimension重要尺寸 Critical Dimension 雕刻 Engrave托司 EJ.GUIDE PIN。
模具零件的中英文标准要点【范本模板】
起支垫作用的板
管位块lock block
起限位作用,又称落位
分型面管位块（凹/凸）P/Llock (female/male）
分型面管位块（凹)P/Llock（female)
分型面管位块（凸)P/Lcock（male）
管位套
Locationset
用于斜顶、斜顶杆、顶针、推方杆、直顶、顶棍的导向定位部件
模具上用来导向用。又称导柱、导边
边司
Guide bush
模具上用来导向用,与导边配合.又称导套、导司
哥林柱
Ejector guide pin/ column
模具上用来对顶出系统导向用。
中托司Ejector guide bush
安装在顶针组板上，用来对顶出系统导向用，与哥林柱配合
4。1模胚组板
类别
标准名称
顶出用的杆，例如RA系列模所用
气咀Air valve
用于气辅模具或模具上使用气拍时从模外进气的喉咀
气拍
Air popper valve
用于辅助开模，帮助顶出。又称气拍镶件、顶出气针
加速顶出器
Accelerated knock—outs
用于模具二次顶出，例如，DME公司标准件AKO—1
旋转块
Rotaryblock
保温铝板
Reflector sheet
HASCO热流道系统上使用的零件（Z1064/。。。)
热流道板附件
Accessory kit
HASCO热流道系统上使用的组件（Z1067/。.。）
热唧咀过滤器
Filter cartridge
HASCO热唧咀使用的零件(Z109/...)
加热板
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
HASCOZ标准件系列Z00 导柱Guide pillarZ01 导柱Guide pillarZ011 导柱Guide pillarZ012 导柱Guide pillarZ013 导柱Guide pillarZ014 导柱Guide pillarZ0141 导柱连接端End pieceZ0142 导柱连接端End pieceZ015 导柱Guide pillarZ0151 导柱连接端(Z015/…专用)Pillar adapterZ0152 导柱连接端Pillar adapterZ02 顶杆Ejector rodZ022 导管Guide sleeveZ03 导柱Guide pillarZ05 圆锥形管精定位Locating unit, roundZ055 圆形垫片SpacerZ056 圆形垫件SpacerZ06 平锥形导块Locating unitZ07 长方形导块Square guide barZ08 直身方形管位导块Pre-centering unitZ081 方形垫片Spacer discZ091 方形定位锁块(公)Square interlockZ092 方形定位锁块(母)Square interlockZ093 方形定位锁块(母)Square interlockZ10 导套Guide bushZ10W 自润滑导套Guide bushZ11 导套Guide bushZ11W 自润滑导套Guide bushZ12 滚珠导套Ball guide bushZ13W 自润滑导套Self lubricate. Guide bush Z15W 自润滑垫片Self lubricate. Flat stock Z16W 自润滑垫片Self lubricate. Guide rail Z17 长方形导块(Z07/...专用)Guide retainerZ20 定板导套Centering sleeveZ25 定位销Dowel pinZ26 定位销Dowel pinZ28 六角螺母Hexagon nutZ281 六角螺母Hexagon nutZ282 六角螺母Hexagon nutZ285 螺母Nut for T-slotsZ286 螺母Nut for T-slotsZ30 胚头内六角螺丝Socket head cap screwZ31 胚头内六角螺丝Socket head cap screwZ32 薄胚头内六角螺丝Socket head cap screwZ33 薄胚头内六角螺丝Countersunk screwZ34 内六角螺丝Hexagon socket set screw Z35 内六角螺丝Hexagon socket set screw Z351 内六角螺丝Hexagon socket set screw Z352 螺丝杆Locking screwZ36 弹簧滚珠螺丝Spring plungerZ361 弹簧滚珠螺丝Spring plungerZ37 弹簧滚珠螺丝Spring plungerZ370 弹簧定位螺丝Spring plungerZ371 弹簧滚珠螺丝Spring plungerZ372 弹簧定位螺丝Spring plungerZ3721 弹簧定位螺丝Spring plungerZ373 弹簧定位镶件Spring plungerZ374 弹簧滚珠镶件Spring plungerZ375 弹簧滚珠镶件Spring plungerZ38 限位螺丝Shoulder screwZ381 螺丝Slotted shoulder screw Z39 螺丝Slotted shoulder screw Z40 顶针(全硬)Ejector pinZ41 顶针(表层硬)Ejector pinZ42 顶头顶针(全硬)Ejector pinZ43 顶头顶针(表层硬)Ejector pinZ44 有托顶针(表层硬)Shouldered ejector pin Z441 有托顶针(全硬)Shouldered ejector pin Z442/.../S 有托顶针(定制件)Ejector pinZ45 司筒(表层硬)Ejector sleeveZ451 司筒(全硬)Ejector sleeveZ4501 司筒(全硬)Ejector sleeveZ452/…/S 司筒(定制件)Ejector sleeveZ453/…/S 司筒(定制件)Ejector sleeveZ454/…/S 司筒(定制件)Ejector sleeveZ455/…/S 司筒(定制件)Ejector sleeveZ456 顶针耐磨镶件Wear sleeveZ456/…/S顶针耐磨镶件(定制件)Wear sleeveZ46 扁顶针(表层硬)Flat ejector pinZ461 特殊扁顶针Special flat ejectorZ462 特殊扁顶针镶件(Z461/…专用)GuideZ465 扁顶针(全硬)Flat ejector pinZ466/…/S 扁顶(定制件)Flat ejector pinZ47 顶针延长杆Extension rodZ48 年月标记镶件Date insertZ4800 标记镶件Marking insertZ4801 更新标记镶件Renew insertZ481 更新年份镶件Year insertZ482 月份标记镶件Month insertZ483 年份标记镶件Year insertZ484 箭头标记镶件Arrow insertZ485 年月标记镶件Date insertZ4851 更新年份镶件Year insertZ4861/1 塑料标记镶件Resin marking insert Z4861/2 班别标记镶件Shift marking insert Z4861/3 日期标记镶件Day marking insertZ4861/4 月份标记镶件Month-marking insert Z4861/5 年份标记镶件Year-marking insert Z4863 年月日标记镶件Multi. Marking insert Z4864 年月日塑料标记镶件Multi. Marking insert Z487/1 “回收标记”嵌件Recycling insertZ487/2 “回收标记”嵌件Recycling insertZ487/3 “回收标记”嵌件Recycling insertZ488 CE 标记镶件CE marking insertZ489 食物标记镶件Food marking insert Z49 模芯镶件Core pinZ491 气动顶出阀Air valveZ492 模芯镶件Core pinZ495 喷气块Blow off stripZ4951 喷气咀Blow off nozzleZ50 唧咀Sprue bushingZ51 唧咀Sprue bushingZ511 唧咀Sprue bushingZ512 唧咀Sprue bushingZ515 气动唧咀Pneumatic nozzleZ516 细水口镶件Nozzle insertZ518 唧咀Sprue bushingZ519 唧咀Sprue bushingZ53 扣水口镶件Sprue pullerZ55 顶针板园垫件Stop pinZ551 顶针板园垫件Stop pinZ56 环子Head for ejector rod Z561 环子Head for ejector rod Z562 介子WasherZ57 园形垫件Support pillarZ571 园形垫件Support pillarZ60 园线弹簧Compression springZ601 园线弹簧Compression springZ62 蝶形弹簧Disc springZ64 方线弹簧Compression spring Z65 扁线弹簧Compression spring Z67 弹弓介子环Retaining ringZ671 弹弓介子钳Mounting pliersZ68 弹弓介子环Retaining ringZ681 弹弓介子钳Mounting pliersZ69 螺丝介子Spring washerZ691 螺丝介子Spring washerZ70 吊架连吊环Lifting deviceZ701 调距螺栓Distance boltZ71 吊环Eye boltZ711 吊环Eye boltZ712 吊环Eye boltZ72 吊环Eye boltZ73 安全扣Tool safety device Z741 固定玛夹Power clampZ7411 空板架Spacer blockZ7412 空板架Spacer blockZ742 固定玛夹Power clampZ743 固定玛夹Power clampZ75 固定玛夹Clamp systemZ751 T头螺丝T head boltZ752 T头螺丝T head boltZ7521 T 头螺丝T head boltZ7522 T 头螺丝T head boltZ753 介子环Spherical washerZ754 介子环Conical seat washer Z755 介子环Conical seat washer Z76 快速玛夹模装置Quick clamping jig Z761 快速玛夹模板Clamping plateZ762 玛夹导柱Clamping boltZ763 玛夹锁钉Eccentric boltZ765 离合锁(套)Locking housingZ766 离合锁(插)Locking plugZ80 带阀快接喉套Shut-off coupling Z80/…/45 带阀快接喉套Shut-off coupling Z80/…/90 带阀快接喉套Shut-off coupling Z801 快接喉套CouplingZ801/…/45 快接喉套CouplingZ801/…/90 快接喉套CouplingZ805 带阀侨式快接喉套Diverting coupling Z8051 侨式快接喉套Diverting coupling Z807 带阀快接喉套Shut-off coupling Z807/…/45 带阀快接喉套Shut-off couplingZ807/…/90 带阀快接喉套Shut-off couplingZ808 快接喉套CouplingZ809 带阀快接喉套Multi. shut-off coupling Z81 快接喉咀NippleZ81/…/90 喉嘴NippleZ811 带阀快接喉咀Shut-off nippleZ812 适配连接头Double sided connector Z814 适配连接头AdapterZ815 适配连接头AdapterZ817 喉咀Hose nippleZ819 带阀快接喉咀Multi. shut-off nipple Z82 带阀快接喉套Shut-off couplingZ83 喉咀Hose connectorZ831 快接喉套Plug-in connectorZ84 PVC喉管PVC-HoseZ85 PVC喉管PVC-HoseZ851 PVC喉管PVC-HoseZ853 耐高温喉管Viton-HoseZ854 耐高温喉管Teflon-HoseZ855 耐高温喉管Corrugated metal hoseZ86 喉箍Hose clipZ861 紧夹用喉箍Crimping sleeveZ865 紧夹用喉钳Crimping toolZ87 喉咀Hose nippleZ875 喉咀Hose nippleZ876 喉咀Hose nippleZ876/…/45 喉咀Hose nippleZ876/…/90 喉咀Hose nippleZ877 连接头Joining pieceZ878 转曲连接头ConnectorZ88 喉咀Hose nippleZ89 喉咀Hose nippleZ90 加长快接喉咀Extension nippleZ905 适配连接头AdapterZ906 延长管Extension tubeZ91 加长喉咀Extension tubeZ93 密封胶布Sealing tape (Teflon)Z94 喉塞Tapered plugZ941 喉塞Tapered plugZ942 膨胀喉塞Sealing plugZ945/1 套装拉胀喉塞工具Assembly-setZ945/2 套装拉胀喉塞工具Assembly-setZ947/1 拉胀工具延长杆Extended scale tubeZ947/2 拉胀工具延长杆Extended scale tubeZ95 钢管Brass tubeZ96 运水铝质螺旋芯(单) Spiral coreZ961 运水铝质螺旋芯(双) Spiral coreZ962 运水针Junction tubeZ964 运水回路胶环(小) Diverting elementZ9641 运水回路胶环(大) Diverting elementZ965 运水胶隔片Plug baffleZ967 隔水片Baffle coreZ968 运水胶质螺旋芯Spiral coreZ969 运水胶质螺旋芯Spiral coreZ97 运水针Cascade water junction Z975 特快导热针Heat pipeZ98 耐高温密封胶圈O-RingZ1001 阀针Needle valveZ101 电热喷咀Hot nozzleZ101G 电热喷咀Hot nozzleZ101R 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ1011 电热喷咀内胆Inner part of nozzle Z1011M 电热喷咀内胆Inner part of nozzle Z1015 金属密封圈Metal O-RingZ103 电热喷咀Hot nozzleZ103G 电热喷咀Hot nozzleZ103R 电热喷咀Hot nozzleZ1031 电热喷胆内胆Inner part of nozzle Z103T 电热喷咀Hot nozzleZ103GT 电热喷咀Hot nozzleZ103RT 电热喷咀Hot nozzleZ1031T 电热喷胆内胆Inner part of nozzle Z103M 电热喷咀Multiple gate nozzle Z1031M 电热喷胆内胆Inner part of nozzle Z10320 电热喷咀Muitlple gate nozzle Z10370 电热喷咀Muitlple gate nozzle Z104 电热喷咀Hot nozzleZ104G 电热喷咀Hot nozzleZ104R 电热喷咀Hot nozzleZ1041 电热喷胆内胆Inner part of nozzle Z104E 电热喷咀Hot nozzleZ104GE 电热喷咀Hot nozzleZ1041E 电热喷胆内胆Inner part of nozzle Z104GV 电热喷咀Hot nozzleZ1041V 电热喷咀内胆Inner part of nozzle Z10420 电热喷咀Muitlple gate nozzleZ1052 圆形隔热垫件Distance ringZ1055 炉头接驳衬套Sprue bushingZ106 热流道板ManifoldZ10600 热流道板ManifoldZ1061 密封塞钉PlugZ1062 密封圈Sealing washerZ1063 六角螺丝Hexagon head screwZ1064 保温铝板Reflector sheetZ1067 套装零件Accessory kitZ107 气动针阀Needle valveZ1072 针阀司套Needle guide sleeveZ1073 针阀司套Needle guide sleeveZ1076 圆形隔热垫环Distance ringZ109 过滤器Filter cartridgeZ1095 过滤器Filter cartridgeZ110 发热棒Cartridge heaterZ111 发热棒Cartridge heaterZ1133 发热环Heater bandZ1134 发热环Heater bandZ1138 发热管(可弯曲) Fiexble heaterZ116 套装接线工具Assembly setZ1161 耐高温电线Extension cableZ1162 线耳Crimp type bracketZ1164 耐高温电线Extension cableZ1165 连接管Butt jointZ1166 线耳Cable end sleeveZ1167 套件Assembly kitZ1168 热电偶线Signal cableZ121 隔热板(洞、无洞) Insulating sheetZ1211 隔热板(洞、无洞) Thermal insulating sheetZ122 电热温控器Temperature controllerZ1221 温控器组件ModuleZ1224 插座嵌件Socket insertZ1225 温控器连接线Connection power/signalcableZ1226 温控器连接线(转换用) AdapterZ1227 插座ScoketZ1228 插座ScoketZ1229 插座嵌件InsertZ123 多组温控器Multi zone control system Z125 温控器Temperature controllerZ126/1 温控器Temperature controllerZ126/2 温控器Temperature controllerZ1261 温控器ModuleZ1262 盖板Cover PlateZ127 插头PlugZ128 插头CouplingZ1292 多组温控器系统Multi zone control unitZ1295 热电偶ThermocoupleZ1295/1 热电偶ThermocoupleZ1295/3 热电偶ThermocoupleZ1295/5 热电偶ThermocoupleZ1296 电热固定座Coupling nippleZ1297 电热固定座Fastening nippleZ131 接线盒Wiring boxZ1312 隔热板Thermal insulating sheetZ1370 压力感应器Pressure transducerZ1371 压力感应器Measuring tongueZ1372 压力感应器Measuring measuring tongue Z1373 压力感应器Force transducerZ1381 连接线Connection cableZ1382 连接线Connection cableZ1383 连接线Connection cableZ1384/1 放大器(压-电) Charge amplifierZ1385/2 数据转换器Data converterZ1387 连接线Connection cableZ1391 替代插件DummyZ1392 固定支架BracketZ1393 替代插件DummyZ1394 固定支架BracketZ1395 固定支架Mounting plateZ1396 安装导管Spacer tubeZ1397 安装导套Mounting nutZ1398 安装导杆Tubular wrenchZ1399 安装导杆Insertion toolZ140 磁感应限位开关Limit switchZ1401 连接线Connection cableZ1402 连接线Connection cableZ141 测试表TesterZ145 红外线物体探测器Infrared control unitZ1451 红外线发送器Infrared transmitterZ1452 红外线接收器Infrared receiverZ1453 红外线发送器Infrared transmitterZ1454 红外线接收器Infrared receiverZ1455 固定支架BracketZ1457 接线盒Wiring boxZ1458 连接线Connection cableZ1460 隔热板Thermal insulating sheetZ1471 感应开关器Inductive proximity switch Z1473 感应开关器Inductive proximity switch Z1475 感应开关器Inductive proximity switch Z1500 来福线丝杆(L/左、R/右) Helical spindleZ1520 来福线丝套(L/左、R/右) Helical nutZ1540 齿条RackZ1550 带齿轮圆模芯Geared-spindle coreZ1552 螺母铜司(原料) Pilot threat bush blankZ1553 齿轮Gear wheelZ1555 齿轮Gear wheelZ1558 平键Parallel keyZ1560 圆锥滚柱轴承Roller bearingZ1562 滚珠轴承Ball bearingZ1564 滚柱压珠轴承Needle-thrust ball bearing Z1565 耐磨轴承内环Thrust ringZ1566 滚柱压柱轴承Needle-thrust rollerbearingZ159 顶杆连接装置Ejector coupling deviceZ1591 连接头Coupling spigotZ1592 长接头coupling rodZ163 复位衬套Pressure sleeveZ164 复位导套BushZ165 顶板复位装置Pull back deviceZ166 复位顶出杆Ejector rodZ167 法兰盘Locking flangeZ168 快速联接装置Rapid couplingZ1681 联接杆Ejector rodZ1682 联接杆Ejector rodZ169 二级顶出装置Two-stage ejectorZ1695 二级顶出装置Two-stage ejectorZ1696 适配器AdapterZ170 程序模板开合装置Latch locking unitZ171 程序模板开合装置Latch locking unitZ172 模板开合胶塞(涨钉) Frictional pullerZ1721 模板开合胶塞(涨钉) Frictional pullerZ173 程序模板开合装置Round latch locking unitZ1731 程序模板开合拉杆Pulling rodZ1732 拉杆衬套Threaded bushZ174 程序模板开合装置Latch locking unitZ1751 斜齿条RackZ1752 斜齿条RackZ1754 斜齿条滑动方铁Guide blockZ1755 斜齿条固定方块Mounting blockZ1756 方铁Spacer blockZ1761 双面斜齿条PackZ1764 斜齿条滑动方铁Guide blockZ180 滑块SlideZ181 滑块组件Mould slide unitZ1810 锁定块Locking heelZ182 锁定块Locking heelZ1821 耐磨垫板Wear plateZ183 锁定块Duble locking heelZ1831 防磨垫板Wear plateZ1832 防磨垫板Wear plateZ185 滑块管导块Guide stripZ185W 自润滑块管导块Self lubric.Guide stripZ186W 自润滑垫板Self lubric.Flat stockZ187 斜导柱固定导套RetainerZ200 热喷嘴Hot nozzleZ2300 正向锁定液压缸Positive locking cylinder Z2310 固定块FlangeZ2320 适配器AdapterZ2330 适配器螺丝Pressure screwZ240 气动阀式开闭控制器Pneumatic control unitZ2401 摇臂式阀Rocker arm valveZ2411 油水分离器Lubro-control unitZ2412 油水分离器Lubro-control unitZ2416 消音塞SilencerZ251/2 测温表Temperature deviceZ2511 测温针Temperature feelerZ2512 测温针Temperature feelerZ2515 测温针Temperature feelerZ252 测温表Pocket temp.measuringdeviceZ255 精度量度针规Inspection pin setZ256 针规钳Inspection pin holderZ257 精密薄垫片Gauge shim stockZ260 耐温润滑油Heavy duty lubricantZ261 耐温润滑喷剂Heavy duty lubricantZ262 防锈喷剂Heavy duty lubricantZ263 清洁喷剂Multi purpose cleaner spray Z264 矽质离模剂Silicone sprayZ265 脱模剂Release agentZ266 发热棒安装用喷剂Special assembly sprayZ267 除锈喷剂Rust solventZ268 特效润滑喷剂Teflon-lubricating sprayZ269 表面防护剂Surface protectionZ3307 注孔衬套镶件Chamber insertZ3308 密封套环Sealing ringZ3309 承托套管Spacer sieeveZ3310 电热喷咀Hot nozzleZ3340 电热喷咀Hot nozzleZ3360 电热喷咀Hot nozzleZ33201 电热喷咀Hot nozzleZ33202 电热喷咀Hot nozzleZ3500 电热喷咀Hot nozzleZ3501 电热喷咀Hot nozzleZ3510 喷咀镶件Nozzle Tip,3-hole type Z3512 喷咀镶件Nozzle Tip,1-hole type Z3520 喷咀镶件Nozzle Tip,3-hole type Z3522 喷咀镶件Nozzle Tip,1-hole type Z3550 喷咀主体Nozzle bodyZ3351 发热套HeaterZ3352 热电偶Thermo coupleZ3353 分隔帽(防止塑料滞留) Insulator capZ3554 密封环套Sealing ringZ3555 垫环Spacer discZ3556 承托套管Spacer sleeveZ3560 注孔衬套镶件Melt chamber insertZ3561 注孔衬套镶件Melt chamber insertZ3580 发热套拆卸工具Dismantling toolZ3581 六角套筒Box spannerZ3600 推缩模芯Collapslble coreZ6007 不锈钢快接喉套CouplingZ6015 不锈钢快接喉套CouplingZ6025 不锈钢快接喉套CouplingZ6055 不锈钢快接喉套CouplingZ6065 不锈钢快接喉套CouplingZ6075 不锈钢快接喉套CouplingZ6107 不锈钢带阀喉套CouplingZ6115 不锈钢带阀喉套CouplingZ6125 不锈钢带阀喉套CouplingZ6155 不锈钢带阀喉套CouplingZ6165 不锈钢带阀喉套CouplingZ6175 不锈钢带阀喉套CouplingZ6302 不锈钢快接喉套NippleZ6303 不锈钢快接喉套NippleZ6305 不锈钢加长喉咀Extended nippleZ6340 不锈钢加长喉咀Extended nippleZ6353 不锈钢带阀喉咀NippleZ6505 不锈钢喉咀Hose connectorK100 固定环Location ringK103 固定环Location ringK500 固定环Location ringK503 固定环Location ringK505 固定环Location ringA1255 洗石笔Trueing diamondA1265 Dressind stoneA1910 Cutting wheelA1915 Special grinding wheelA1930 Diamond cutting wheelA1931 Boronnitrid cutting wheel A1935 Diamond grinding wheelA1936 Boronnitrid grinding wheel A2500 锥形钻咀Tapered drillA2600 锥形镰靶Tapered reamerA2700 沉头锣刀Counter boreA2710 密封圈用坑槽锣刀Circular groove cutterA2715 固定钉Guide spigotA2720 沉头锣刀Special counter boreA2800 螺丝牙攻Tap setA3500 长方形电蚀铜料EDM copperA3501 长方形电蚀铜料EDM copperA3502 园方形电蚀铜料EDM copperA3503 园方形电蚀铜料EDM copperA3504 园方形电蚀铜料EDM copperA3510 长方形电蚀石墨料EDM GraphiteA3511 园方形电蚀石墨料EDM GraphiteA3514 长方形电蚀石墨料EDM GraphiteA3515 园方形电蚀石墨料EDM GraphiteA3541 回收再造标记石墨工Graphite electrodeA3542 回收再造标记石墨工Graphite electrodeA3543 回收再造标记石墨工Graphite electrodeA3545 CE标记铜工CE marking electrodeA3546 食品标记铜工Food marking electrodeA3547 回收再造标记铜工Recyc.Marking electrodeA4700 套装气喷枪Airblow kitA4720 气喉管Spiral hoseA5000 撞激拉出工具Extraction tool kitA5050 六角匙Hexagon keyA5051 六角匙Hexagon keyA5053 六角匙Hexagon key with pilotA5055 六角匙Hexagon keyA5060 套装六角匙Hexagon key setA5061 套装六角匙Hexagon key setA5080 Slotted nut driverA5120 扳手Sickle spannerA5121 扳手Pin wrenchA5130 六角套筒Box spannerA5710 开合计数器Cycle counterA5712 可重置开合计数器Cycle counter,resetabie A5714 双合式计数器Combinedcycle counter A5716 复合式计数器Unibersal counterA5720 重置器Resetting toolsA5722 塑质固定框架Insulating frameA5723 铝质固定框架Insulating frameH1050 蕉形浇口镶件Gate insertH1060 蕉形浇口镶件Gate insertH5050 过滤器Filter cartridgeT4010 绿色扁线弹簧Compression springT4020 蓝色扁线弹簧Compression springT4030 红色扁线弹簧Compression springT4040 黄色扁线弹簧Compression spring。