《汽车常用英文术语200个》
最全汽车行业术语英文翻译
最全汽车行业术语英文翻译1. 汽车类型- Sedan: 轿车- Hatchback: 掀背车- SUV (Sport Utility Vehicle): 运动型多功能车- MPV (Multi-Purpose Vehicle): 多功能车- Coupe: 轿跑车- Convertible: 敞篷车- Pickup: 皮卡车- Van: 面包车- Electric Vehicle (EV): 电动汽车- Hybrid Vehicle: 混合动力汽车2. 发动机和动力系统- Engine: 发动机- Horsepower (HP): 马力- Torque: 扭矩- Fuel Injection: 燃油喷射- Turbocharger: 涡轮增压器- Supercharger: 机械增压器- Cylinder: 气缸- Transmission: 变速器- Manual Transmission: 手动变速器- Automatic Transmission: 自动变速器- Continuously Variable Transmission (CVT): 连续变速器- Four-Wheel Drive (4WD): 四轮驱动- All-Wheel Drive (AWD): 全轮驱动- Electric Motor: 电动机- Battery Pack: 电池组3. 车身部件- Chassis: 底盘- Bodywork: 车身- Hood: 发动机盖- Trunk: 后备箱- Bumper: 保险杠- Fender: 车翼- Door: 车门- Windshield: 前挡风玻璃- Roof: 车顶- Spoiler: 尾翼- Headlights: 前灯- Taillights: 尾灯4. 汽车零部件- Brakes: 制动器- Suspension: 悬挂系统- Steering Wheel: 方向盘- Tires: 轮胎- Exhaust System: 排气系统- Air Conditioning: 空调系统- Radiator: 散热器- Battery: 电池- Alternator: 发电机- Starter Motor: 起动机- Fuel Pump: 燃油泵- Ignition System: 点火系统5. 汽车性能指标- Acceleration: 加速度- Top Speed: 极速- 0-60 mph Time: 0-96公里/小时加速时间- Fuel Efficiency: 燃油效率- Range: 续航里程- Curb Weight: 空载重量- Gross Vehicle Weight (GVW): 总重量- Wheelbase: 轴距6. 安全设备- Seatbelt: 安全带- Airbags: 气囊- Anti-lock Braking System (ABS): 防抱死制动系统- Electronic Stability Control (ESC): 电子稳定控制系统- Tire Pressure Monitoring System (TPMS): 轮胎气压监测系统- Adaptive Cruise Control: 自适应巡航控制- Blind Spot Detection: 盲点监测以上是最全汽车行业术语的英文翻译,希望能对您有所帮助!。
汽车常用英文术语200个
57 Crankshaft 58 Cycle 59 Cylinder 60 Dash
CR/SHF CYL CYL
曲轮轴 环 气缸 前围
61 Defroster 62 Department 63 Device 64 Disc 65 Display 66 Door
《汽车常用英文术语 200个》
No 英文全称 .1 Actuator
2 3 4 5 6 7 8 Adhere Adjust Air Bag Air Conditioner Alarm Alternator Antenna
英文缩
ACTR 写 ADJ AB A/C ALTN ANT ABS 作动器 粘贴 调整 气囊 空调 警报 发电机 天线
A/T
自动变速器 车桥、车轴 后部、倒车
BAG BAL
行李 平衡 杠、条 批号 蓄电池 轴承 皮带
BATNO BAT BRG
23 Blade 24 Block 25 Blower 26 Body 27 Body Side 28 Bolt BD B/S
刮片 缸体 鼓风机 车体 侧围 螺栓
29 Booster 30 Bow-Roof 31 Box 32 Bracket
搁脚板支架 前门上铰链总成 前制动盘 油箱管护板 供油软管 保险丝盒盖总成 保险丝夹 左中立柱下饰板 行李箱上饰板 制动管衬垫 密封垫圈 动力转向机总成 前风窗玻璃总成 后挡风玻璃 左三角玻璃 资料盒盖总成 散热器格栅总成 左前除霜器格栅 机油标尺杆总成 散热器防溅板总成
93 Glove Box 94 Grill 95 Grommet 96 Guage 97 Guard-Splash 98 Hand Brake 99 Handset 100 Harness GROM
汽车行业英语专业术语
汽车行业英语专业术语汽车行业英语专业术语1 ACC activated carbon canister 活性碳罐2 ACI automatic car identification system 汽车自动识别系统3 air cushion car 气垫车4 air-cooled car 空气冷却式汽车,空冷式车辆,空冷式轿车(装用空冷式发动机的轿车)5 APC aperture card 穿孔卡片6 ASU automatic interference suppression for car radios suppresses ignition noise in the FM band 调频干扰自动抑制,在汽车收音机中附加入此电路即可抑制高压点火(噪音)的干扰7 baby car 微型轿车,超微型轿车(美俚语,=mini car,cycle car,midget car);婴儿小车8 backfiring in carburetor 化油器回火(=explosion in the carburetor)9 baggage car 行李车10 brake shoe carrier 制动蹄座11 brush carrier 刷架12 C&M care and maintenance 维修及保养13 C.CARB conventional carburetor 常规化油器14 C.P. car park (停)车场15 C/O carry over 携带16 cable-testing car 电缆检查车17 car aerial 汽车天线(=automobile aerial)18 Car Alarm theft-deterrent system 汽车防窃警报系统19 car antenna 车上天线,车载天线,汽车天线20 car body 轿车车身21 car mechanic 汽车维修工,机动车维修工22 car navigation computer 车用导航计算机,车用导行计算机23 car park 停车场,停车处24 car waiting to repair 待修汽车25 car wander 汽车蛇行26 car wash 洗车台,汽车清洗站27 car wash trade 洗车业28 car washer 洗车设备,洗车机;街道清洗机29 car washing department 洗车工间,车辆清洗工间30 car washing installation 洗衣装置,洗车设备31 car washing installation 洗衣装置,洗车设备32 car washing machine 洗车机33 car with elevator 带升降机车辆,升降机汽车34 car with four independent wheels 四轮独立悬架式轿车35 carb 化油器,汽化器(carburator的简称)36 CARB 1.化油器(carburettor) 2.碳化,渗碳(carbonization)37 carb adjustment 化油器调准,化油器调节38 CARB California Air Resources Board 加里福尼亚大气资源局39 CARB carburetor 化油器,汽化器40 carboard 纸板,硬纸板41 carbon 碳(代号C);碳棒,电刷,石墨,积炭,积碳层42 carbon electrode 碳棒,碳电极43 carbon monoxide 一氧化碳(CO)44 carbonization test (润滑油)积炭试验45 CARE corporate average regulated emission 公司规定的'平均有害物排放量46 CARP cooperate automotive research program 汽车合作研究程序47 CARR carriage 车溜板48 CARR carrier 运载工具,载体49 carriage 车辆,车架,支架,托架;(机床的)拖板;机器的滑动部分;底座,底盘;承重装置,承载器;运输,运费50 carriage body 车身51 CARS computer aided routing system 计算机辅助(运输网络中)选线系统52 CART carton 卡片纸53 cartridge 管壳,盒;卡盘,夹头;座;套筒;衬套(过滤器的)芯子;(照像)胶卷;支架54 cartridge fuse 熔断丝管,熔断丝55 cartridge paper 画图纸,图画纸56 CAT carburetor air temperature 化油器空气温度57 CFC chlorofluorocarbons 含氯氟烃(氟属致冷剂)58 CFRC carbon fiber friction material 碳纤维摩擦材料59 CFRP carbon fiber reinforced plastic 碳纤维强化塑料60 CL car load 车辆载负。
汽车--常用术语
汽车--常用术语常用术语1、汽车类型:the type of automobile汽车:motor vehicle,automobile载货车:truck 微型货车:mini-truck 轻型货车:light-truck中型货车:medium truck 重型货车:heavy truck 越野车:off-road vehicle自卸车:dump truck 牵引车:towing vehicle专用汽车:special purpose vehicle 客车:bus 轿车:passenger car微型轿车:mini-car 普通级轿车:subcompact car 中级轿车:compact car中高级轿车:intermediate car 高级轿车:limousine car2、汽车尺寸:dimension of vehicle车长:vehicle length 车宽:vehicle width 车高:vehicle height轴距:wheel space 轮距:track 前悬:front overhang后悬: rear overhang 最小离地间隙:ground clearance车轮外倾:camber angle 主销内倾: kingpin inclination 前束toe-in3、发动机:engine发动机总体构造和工作原理:the construction and working principle汽油机gasoline engine 柴油机diesel engine四冲程发动机four-stroke engine 单(多)缸发动机single(multi)-cylinder engine 立(斜、卧)式发动机vertical (inclined、horizontal) engine工作循环working process进气(压缩、膨胀、排气)行程suction(compression、expansion 、exhaust) stroke 点火次序firing order 上(下)止点top(bottom) dead centre活塞行程piston stroke 气缸工作容积piston swept volume发动机排量engine swept volume 充气系数volumetric efficiency配气相位valve timing 压缩比compression ratio直接喷射direct injection 间接喷射indirect injection喷油压力injection pressure 电控喷射electronic-controlled injection雾化atomization 混合气浓度mixture concentration可燃混合气combustible mixture 空燃比air-fuel ratio过量空气系数excess air ratio 燃烧室combustion chamber压燃compression ignition 点燃spark ignition抗暴性antiknock quality 增压中冷inter-cooling负荷load 空载no-load工况working condition曲柄连杆机构:connecting rods and crankshaft缸盖cylinder head 气缸cylinder缸体cylinder block 缸套cylinder liner油底壳oil pan 活塞piston活塞环(销) piston ring(pin) 气(油)环compression(oil control) ring连杆connecting rod 曲柄crank曲轴crankshaft 飞轮flywheel配气机构:valve gear凸轮(轴)cam(camshaft) 进(排)气阀inlet (exhaust) valve挺柱tappet 推杆push-rod摇臂rocker arm燃油供给系统:fuel system柱塞(转子)式喷油泵jerk fuel injection pump喷油器injector 调速器governor发动机调速系统:engine speed governing排放控制系统:emission control system发动机冷却系统:engine cooling system发动机润滑系统:engine lubrication system发动机点火系统:engine ignition system发动机起动系统:engine starting system5※<标题二>4、汽车底盘术语离合器:clutch摩擦离合器friction clutch(单盘single plate、双盘twin double plate、多盘multi-plate、膜片弹簧diaphragm spring、自动automatic、电磁electromagnetic)离合器操纵机构clutch operation 压盘pressure plate分离杆release lever 分离筒release sleeve离合器盖clutch cover 从动盘clutch plate从动盘毂clutch plate hub 分离弹簧(轴承)release spring(thrust bearing)中间压盘center plate 压紧弹簧pression减振弹簧damping spring 摩擦片plate friction lining扭转减振器torsional damping arrangement变速器:transmission, gearbox机械式变速器mechanical transmission自动变速器automatic transmission主(副)变速器basic(splitter) transmission行星齿轮变速器planetary transmission液力偶合器fluid coupling 液力变矩器torque converter万向传动装置:十字轴(非等速、等速、准等速、挠性、双联、球销、球笼)万向节cardan (nonconstant velocity、constant velocity、near constant velocity、flexible、double cardan、ball and trunnion、rzeppa) universal joint十字轴总成cross assembly 万向节叉yoke驱动桥:driving axle断开(非断开)式驱动桥divided (rigid) drive axle单(双)级主减速器single (double) reduction final axle齿轮(防滑、自锁、摩擦)差速器gear (limited-slip、self-locking、multi-disc) differential 桥壳axle housing全浮(半浮)式半轴full-floating (semi-floating) axle shaft转向系:steering system机械(动力)转向系manual (power) steering system 转向器steering gear转向盘(轴、操纵机构) steering wheel (shaft、control mechanism)循环球-齿条齿扇(齿轮齿条)式转向器recirculating ball-rack and sector (rack and pinion ) steering gear正(逆)效率forward(reverse) efficiency行驶系:running system独立(非独立)悬架indepenndent (rigid axle) suspension钢板(螺旋、扭杆、空气、橡胶、油气)弹簧leaf(coil、torsion bar、air、rubber、hydro-pneumatic) spring减震器shock absorber 横向稳定器stabilizer anti-roll bar制动系:braking system鼓(盘)式制动器drum (disk) brake 驻车制动装置parking braking device制动鼓(蹄、钳)brake drum (shoe、caliper)5※<标题三>《汽车理论》1 汽车动力性vehicle tractive performance2 加速时间time of acceleration3 最大爬坡度maximum grade ability4 驱动力tractive force5 发动机的调速特性fixed throttle characteristics6 适应性系数adaptive coefficient7 机械效率mechanical efficiency8 行驶阻力resistance 9 滚动阻力rolling resistance10 弹性迟滞elastic slow-moving 11 滚动阻力矩moment of rolling resistance12 滚动阻力系数coefficient of rolling resistance13 切向反力tangential force 14 法向反力normal force15 空气阻力aerodynamic resistance16 空气阻力系数aerodynamic resistance coefficient17 坡道阻力grade resistance 18 道路阻力resistance of the road19 加速阻力accelerating resistance;inertia force20 旋转质量换算系数correction coefficient of rotating mass21 附着力adhesive force 22 切向反作用力tangential force23 法向反作用力normal force 24 附着系数coefficient of adhesion25 后备功率power reserve 26 发动机比功率power/mass ratio27 燃料经济性fuel economy 28 燃油消耗率specific fuel consumption29 万有特性cross sectional characteristics30 负荷特性part throttle characteristics31 道路循环油耗fuel economy of road test cycles32 制动性braking performance 33 地面制动力type-ground braking force34 制动器制动力braking force originated from brake system35 制动减速度braking deceleration 35 制动距离braking distance37 同步附着系数synchronizing adhesion coefficient38 侧倾角速度roll velocity 39 俯仰角速度pitch velocity40 横摆角速度yaw velocity 41 轮胎坐标系tire axis system42 轮胎侧偏角side-slip-angle 43 侧偏刚度cornering stiffness44 回正力矩aligning torque 45 转向特性steering characteristics46 侧偏力cornering force 47 横摆角速度增益yaw velocity gain48 临界车速critical speed 49 特征车速characteristic speed50 不足转向under steer 51 过多转向over steer52 中性转向neutral steer 53 静态储备系数static margin54 瞬态响应transient state response 55 稳态响应steadies state response56 汽车平顺性ride of the automobile57 路面谱spectrum of road surface roughness58 空间频率spatial spectral density 59 空间频率谱spatial spectral density60时间频率谱spectral density 61 最小离地间隙ground clearance62 汽车的通过性mobility over unprepared terrain63 纵向通过角ramp angle 64 接近角approach angle65 离地角departure angle 66 最小转弯直径diameter of turning circle67 转弯通道圆turning clearance circle 68 功率循环circulation of power69 牵引阻力tractive resistance 70 牵引力(功率)曲线图tractive-power chart71 最高车速maximum velocity 72 发动机外特性engine characteristic at maximum opening of valve73 制动效能brake efficiency 74 转向稳定性cornering stability75 后轴侧滑sideslip of rear axle 76 甩尾trail swing77 评价指标evaluated standard 78 操纵稳定性steering stability81 主销后倾kingpin caster 82 主销内倾kingpin inclination83 功率平衡图tractive and resistance power graph84 动力因数dynamical factor85 制动跑偏braking deviation from 86 制动力分配brake banlance87 制动防抱死ABS(Anti-lock Braking System)88动力特性dynamical characteristics89 横向稳定性stability of landscape orientation90 侧偏特性cornering characteristics91 轮胎花纹tire pattern 92 汽车技术状况technical condition of vehicle 93 暴露极限exposure boundary 94 发动机测功器engine dynamometer95 发动机综合试验机motor analyze / engine analyzer96 底盘测功器chassis dynamometer97 车轮功率平衡机dynamic wheel balancer98 前束量尺toe-in ganger 99 外倾测量器camber gauge100 红外线废气分析仪infrared rays exhaust gas analysis apparatus疲劳-降低工作效率界限fatigue-decreased proficiency boundary舒适降低界限decreased comfort boundary5※<标题四>《汽车设计》绪论introduction全球定位系统Global Position System计算机辅助设计Computer Aided Design自适应巡航控制系统Autonomous Intelligent Cruise Control电子伺辅开车Drive by wire防抱死制动系统Anti-block Brake System主动悬架Active Suspension被动悬架Passive Suspension半主动悬架Semi-Active Suspension自动变速器Automatic Transmission电控转向系统Electronic Control Steering通用汽车公司General Motors Company成本竞争能力Cost Competitiveness成本杀手Cost killer运动型多用途车Sport & utility vehicle概念设计Concept Design前置前驱Front-engine Front-drive前置后驱Front-engine Rear-drive后置后驱Rear-engine Rear-drive中置后驱Middle-engine Rear-drive全轮驱动Full-wheel-drive长头式Cab-behind-engine truck平头式forward control layout cab or cab forward type 短头式short bonneted type轴距wheel base轮距wheel center distance装载量weight-carrying capacity整车整备质量weight empty总质量weight in running order轴荷分配axle load ( weight)直接档direct drive燃油经济性fuel economy百公里油耗fuel consumption of 100km通过性throughput capacity最小转弯半径minimum negotiable radius总体布置general arrangement纵梁frame side member or frame girder member横梁frame cross member离合器设计clutch design从动盘clutch driven plate or clutch spider膜片弹簧diaphragm spring压盘pressure plate摩擦片clutch facing从动钢片clutch cushion disk or cushion spring扭转减振器torsion vibration damper or torsion damper 花键毂splined hub变速器设计transmission design中间轴式变速器countershaft transmission直齿spur gear斜齿圆柱齿轮helical gear换档机构gear shift mechanism直齿滑动齿轮shifting slider gear啮合套shifter collar同步器synchronizer轴承bear飞溅润滑plash oiling压力润滑full pressure oiling 换档位置图gear shifting diagram 第一轴input shaft中间轴counter shaft第二轴output shaft万向节设计universal joint柔性万向节rubber universal joint刚性万向节rigid cardan驱动桥drive axle主减速器final gear差速器differential车轮传动wheel driver驱动桥壳rear-axle housing整体式驱动桥壳one-piece housing 主减速比final drive ratio螺旋锥齿轮helical bevel gear双曲面齿轮hypoid bevel gear圆柱齿轮helical spur gear蜗轮蜗杆worm-and-gear (wheel)行星齿轮planetary gear最小离地间隙minimum ground clearance of rear axle摩擦片式差速器sure-grip differential半轴half rear axle悬架设计suspension design弹性元件springs导向机构guider减振器absorber缓冲块bumper横向稳定杆stabilizer钢板弹簧spring leaf螺旋弹簧spiral spring扭杆弹簧torsion bar spring橡胶弹簧rubber spring空气弹簧air spring油气弹簧oiliness spring横向摆臂式独立悬架ndependent wheel suspension by swinging arms 纵向摆臂式独立悬架independent suspension by swinging arms 不等长双横臂式独立悬架long and short arm suspension烛式悬架suspension stuck麦克弗逊式独立悬架suspension McPherson strut 平衡式独立悬架stabilizator suspension主簧mail leaf of spring副簧helper spring制动系brake system制动器brake驱动机构drive unit制动效能braking efficiency领从蹄式制动器leading-trailing shoe brake双领蹄式制动器two leading shoe brake单向增力式制动器half-servo brake横向稳定杆stabilizer bar准双曲面齿轮hypoid gear万向节轴cardan花键spline5※<标题五>《随机振动》1、Random Vibration 随机振动2、Probability 概率3、Statistics 统计4、Random Process 随机过程5、Density 密度6、Frequency 频率7、Discrete 离散8、Wave 波动9、Continuous model 连续模型10、Dynamic 动力的11、Structure 结构12、Dynamic Analysis 动力学分析13、Acceleration 加速度14、Gravitational Acceleration 重力加速度15、Definite Function 有限方程16、Excitation 激励17、Response 响应18、Discrete Model 离散模型19、Stationary 平稳的20、Nonstationary 非平稳的21、Rigid Body 刚体22、Correlation Function 相关函数23、Autocorrelation 自相关24、Spectral Density 谱密度25、Power Spectrum 功率谱26、Ergodic 各态历经的27、Temporal 短时的28、Limitation 极限29、Mean 均值30、Mean Square 均方值31、Variance 方差32、Covariance 协方差33、Variable 变量34、Constant 常数35、Single 单独的36、Filter 过滤37、Cross Correlation 互相关38、Second Order 二阶39、Lag 间隙40、Regular 规律的41、Irregular 不规则的42、Property 特性43、Performance 性能44、Ensemble 整体的45、Even 偶的46、Odd 奇的47、Independent 独立的48、Zero Mean 零均值49、Scatter 离散的50、Period 周期51、Sample 样本52、Uniform 均匀的53、Absolute 绝对值54、Phase 相位55、Circular Frequency 圆频率56、Distributed 分布的57、Dirac Delta Function 狄拉克?得尔塔函数58、Magnitude 模59、Infinite 无穷的60、Periodic 周期的61、Finite 有限的62、Restriction 约束63、Evaluation 估计64、Time Domain 时域65、Frequency Domain 频域66、Fourier Series 富里叶级数67、Fourier Integral 富里叶积分68、Piecewise 分段的69、Fourier Coefficient 富里叶系数70、Complex Number 复数值71、Complex Function 复数函数72、Real Function 实数函数73、Conjugate 共轭74、Parseval’s Formula 帕舍伐尔公式75、Amplitude 振幅76、Impulse 脉冲77、Complex Frequency 复数频域的78、Ordinate 坐标79、Singularity 奇异点80、Harmonic 谐波的81、Narrow Band 窄带82、Wind Band 宽带83、Exponent 指数84、Derivation 导数85、Joint Probability 联合概率分布86、Linear 线性的87、Superposition 重叠88、Inverse Transform 逆变换89、Single Degree of Freedom 单自由度90、Natural Frequency 自然频率91、Damp 阻尼92、Critical 临界的93、Displacement 位移94、Velocity 速度95、Unit Impulse 单位脉冲96、Momentum 动量97、Ordinary Differential Equation 常微分方程98、Complex Frequency Response Function 复频响应函数99、Algebraic Equation 代数方程100、Peak 峰值5※<标题六>《汽车电器设备》蓄电池accumulator电解液electrolyte电路electric circuit开关switch电流表ammeter电压表voltmeter电能electric energy化学能chemical energy电流强度current intensity 脉冲电流pulse current正极板positive plate负极板negative plate单格电池cell比重计hydrometer电极electrode电荷electric charge阳极positive electrode阴极negative electrode电路图circuit diagram电器electric equipment电压voltage电位差potential difference 电源power source充电系charging system交流发电机alternator充电指示器charge indicator 交流电alternating current 直流电direct current二极管diode三极管triode电压调节器voltage regulator 过充电overcharge转子rotor定子stator皮带轮pulley警告灯warning lamp保险丝fusible link短路short circuit电动势electro-motive force 起动系starting system电磁开关magnetic switch起动机马达starter motor机械能mechanical energy飞轮flywheel电磁场electromagnetic field 换向器commutator电刷brush继电器relay电枢armature小齿轮pinion电枢轴armature shaft电刷弹簧brush spring轴承bearing单向离合器overrunning clutch 换档机构shift mechanism电磁线圈solenoid压缩比compression ratio飞轮齿圈flywheel ring gear电枢绕组armature windings换向器片commutator segments 点火系ignition system点火开关ignition switch火花塞spark plug电容器condenser分电器distributor分电器盖distributor cap点火线圈ignition coil初级绕组primary winding次级绕组secondary winding断电器breaker电磁铁electromagnet断电器触点breaker points电火花electric spark分电器点火系统distributor ignition system 空燃比air-fuel ratio火花塞间隙air gap高压high voltage低压low voltage分火头distributor rotor高压线spark plug wire分电器凸轮distributor cam附加电阻ballast resistor点火提前spark advance离心提前centrifugal advance真空提前vacuum advance大气压atmospheric pressure照明lighting照明灯light bulb信号signal报警装置warning equipment仪表meter仪表板instrument panel指示器indicator指示板indicator board指针needle控制电路control circuit辅助设备auxiliary equipment汽油机gasoline engine柴油机diesel engine汽油泵gasoline pump电磁学electromagnetism电磁波electromagnetic wave晶体管点火系统transistorized ignition system无触点电子点火系统breakerless electronic ignition system电磁感应electromagnetic5※<标题七>《汽车电控原理及应用》进气温度(ACT)Air Charge Temperature空气流量传感器(AFS)Air Flow Sensor叶板式空气流量计(V AM)Vane Airflow Meter绝对压力传感器(AIV)Absolute Pressure Sensor空气温度传感器(A TS)Air Temperature Sensor进气温度传感器(ITA)Intake Air Temperature Sensor热线式空气流量计(HW AMMF)Hot-Wire Air-Mass Meter Flow热膜式空气流量计(HFAMFM)hot-film air-mass flow meter 卡门空气流量计(KV AFM)Karman vortex air flow meter大气压力传感器(BARO sensor)barometric pressure sensor 大气压力传感器(BP)barometric pressure sensor节气门关闭位置(CTP)closed throttle position进气温度传感器(IATS)intake air temperature sensor怠速空气控制阀(IACV)idle air control valve可变进气相位(VVT)variable valve timing混合气控制(M/C)mixture control节气门体(TB)throttle body节气门位置(TP)throttle position节气门位置传感器(TPS)throttle position sensor节气门位置开关(TPS)throttle position switch节气门电子控制(ETC)electronic throttle control体积空气流量(V AF)volume air flow电控单元(ECU)electronic control unit燃油喷射系统(INJ)injection system中央多点燃油喷射(CMFI)central multipart fuel ignition连续燃油喷射(CIS)continuous fuel injection直接燃油喷射(DFI)direct fuel injection间接燃油喷射(IFI)indirect fuel injection燃油泵(FP)fuel pump多点燃油喷射(MFI)multipart fuel injection单点燃油喷射(SPI)single point injection顺序电控燃油喷射(SEFI)sequential electronic fuel injection电子燃油控制(EFC)electronic fuel control冷起动喷射(CSI)cold star injection机械连续燃油喷射系统K-Jetronic分配式喷油泵(DFIP)distributor fuel injection pump脉冲调制(PWM)pulse width modulation可变截面喷嘴(V AN)variable area nozzle计算机控制点火(C3I)computer controlled coil ignition汽缸识别传感器(CID)cylinder identification sensor曲轴位置传感器(CKP)Sensor crankshaft position sensor有分电器电子点火EI-with distributor无分电器电子点火系统(EDIS)electronic distributorless ignition system 点火控制模块(ICM)ignition control module整体式电子点火(IEI)integrated electronic ignition感应式脉冲发生器Pickup induction pulse generator霍尔式脉冲发生器Hall-type pulse generator发动机转速及曲轴位置传感器Engine-speed and crankshaft position sensor 发动机转速及凸轮轴位置传感器Engine-speed and camshaft position sensor 车速传感器Speed sensor半导体点火系统Semiconductor ignition system霍尔集成电路(Hall IC)Hall integrated circuit霍尔传感器电压Hall sensor voltage点火提前机构Ignition advance mechanism device真空提前机构Vacuum advance mechanism device离心提前机构Centrifugal timing device unit ;centrifugal timer 电子点火系统EI system electronic ignition system闭环控制(CL)closed loop氧传感器(EGOS)exhaust gas oxygen sensor废气再循环阀(EGRV)exhaust gas recirculation valve氧传感器(EGS)exhaust gas sensor三元催化反应器(TWC)three way catalytic converter执行器Actuator温控定时开关Thermo-time switch凸轮轴位置传感器(CMP Sensor)camshaft position sensor 曲轴位置传感器(CKP Sensor)crankshaft position sensor发动机水温传感器(CTS)engine coolant temperature sensor 汽缸位置(CYP)cylinder position爆震传感器(DS)detonation sensor爆震传感器(KS)knock sensor水温传感器(WTS)water temperature sensor怠速控制(IAC)idle air control曲轴箱强制通风(PCV)positive crankcase ventilation自动变速器(A/T)automatic transaxle (transmission)手动变速箱(M/T)manual transmission无级变速器(CVT)continuously variable transmission 液力偶和器(FCPLG)fluid coupling电控变速器(ECT)electronically controlled transmission 空档开关(NPS)neutral position switch停车/空档位置(PNP)P/N park/neutral position手动停车制动器(PBA)parking brake applied变速器转速传感器(TSS)transmission speed sensor变速器电子控制装置Electronic transmission control计算机控制悬架Computer control suspension液力主动悬架Hydraulic active suspension车轮负荷传感器(WL-sensor)wheel-load sensor行程传感器Travel sensor加速度传感器Acceleration sensor载荷传感器Load sensor车身加速度计Body accelerometer车身高度传感器Vehicle height sensor电子空气悬架Electronic air suspension主动式后轮转向系(ARS)active rear steer system四轮转向(4WS)four wheel steering锁定离合器(L/C)lock-up clutch防滑差速器(LSD)limited slip differential动力转向压力开关(P/S)power steer pressure switch动力控制模块(PCM)power train control module踏板行程传感器(PTS)pedal trechometer sensor车速传感器(VSS)vehicle speed sensor减速传感器Deceleration sensor电子控制四轮转向系Electronically controlled 4WS*system 后轮转向角主传感器Main rear wheel angle sensor后轮转向角副传感器Sub rear wheel angle sensor前轮转向角主传感器Front main steer angle sensor前轮转向角副传感器Front sub steer angle sensor5※<标题八>《汽车计算机辅助设计》计算机辅助设计CAD(computer aideddesign)准时制生产Just in time (JIT)专家系统Expert System(ES)人工智能artificial intelligence客户/服务器Client/Server分布式系统distributed System内部网Intranet外部网extranet浏览器Browser服务器Server网络network局域网Local Area Network(LAN)星形网star network topology以太网Ethernet令牌环Token-ring多媒体Multimedia原型法Prototyping生命周期Life cycle类Class自底向上Bottom-up自顶向下Top-down操作系统Operation System硬件Hardware软件Software数据data数据字典data dictionary数据模型data model数据处理data processing数据结构data structure数据仓库data warehousing数据流data flow数据收集Data Gathering数据处理data processing数据冗余data redundancy信息整体性information integrity逻辑Logical物理Physical实体entity联系Relationship属性Attribute电子商务electronic commerce订单处理sales order processing相关干系人stakeholder participation 系统分析System analysis系统设计System design系统实施System implementation系统评估System assessment顺序结构Sequence条件结构condition输入控制input control处理控制Processing control输出控制Output control界面interface文件File文件传输协议File transfer protocol最终用户End-user密码Password代码Code防火墙Firewall条形码bar code外模式External schema概念模式Conceptual Schema内模式Internal Schema第一范式First Normal Form(1NF)主关键字key知识库knowledge base战略计划strategic planning管理控制Management control运行控制Operational Control结构化决策Programmed decisions管理信息系统Management information system(MIS)企业资源计划Enterprise Resource Planning(ERP)最优化技术Optimized Production Technology(OPT)物料需求计划Material Requirements Planning(MRP)制造资源计划Manufacturing Resource Planning (MRPII)客户关系管理Customer Relationship management(CRM)决策支持系统Decision support system(DSS)电子数据传输Electronic data exchange(EDI)办公自动化系统Office Automation system(OAS)开放系统互连Open system Interconnection (OSI)企业流程重组Business Process Reengineering(BPR)结构化系统开发方法Structured System Development Methodology面向对象方法Object-Oriented Method企业系统规划法Business System Planning(BSP)关键成功因素法Critical Success Factors(CSF)数据库管理系统Database management System(DBMS)面向对象的数据库管理系统object-oriented database management systems(OODBMS) 中央处理器Central Processing Units(CPU)数据流程图data flow diagram(DFD)数据模型规范化Data modeling formalism实体-联系图Entity-relationship diagram实体-联系模型Entity-relationship model实体-联系方法Entity-relationship approach软件开发与维护software development and maintenance 结构化程序设计Structured Programming人面相互作用human-computer interaction信息系统外包Outsourcing of information systems信息系统的安全性security of information system管理信息系统的结构the structure of MIS金字塔型的管理信息系统结构the MIS as a pyramid非结构化决策Non-programmed decisions5※<标题九>《汽车优化设计》优化技术optimization technique优化用数学模型mathematical model for optimization 理论分析法theoretical analysis method类比分析法analogy analysis method汽车选型automobile electrotype投资回收期法payback period method寿命周期费用分析法life cycle cost analysis method 年当量费用valent weight cost per year资金回收系数capital reclamation ratio价值分析法value analysis method汽车动力性motor vehicle dynamic characteristics费用效率分析法cost efficiency analysis method选型优化electrotype optimization技术任务书assignment for technical design技术评价technical evaluation经济评价economical evaluation技术经济优化technical economy optimization实验优化experiment optimization单因素优选法single factor selecting method多因素优选法multifactor selecting method正交实验法orthogonal experiment method汽车使用维修优化automobile utilization and repair optimization 线性规划法liner programming technique分级评分法classified graded method维修服务系统repairing service system维修任务与计划的优化repairing task and plan optimization 分枝界限法branch and bound method计划协调技术plan evaluation and review technique工序时间working procedure time概率计算法calculus of probability method加权平均法method of weighted mean工序最早开工期the earliest time of under stream period事件最迟完工期the latest time of completion date人力安排human resource arrangement缺货费OSS (out of stock) fee确定型模型deterministic model允许缺货的经济定货批量模型economical ordering lot model for permit OOS 生产批量模型production lot model批量回扣模型batch commission model随机性模型randomness model概率密度函数function of density of probability质量评估方法quality evaluation method最优质量水平the best quality level客观性原则principle of objectivity可比性原则comparability principle指向性原则directivity principle缺陷系数法defect coefficient method综合评定法evaluate synthetically method更新优化renewal optimization有形损耗physical depreciation无形损耗invisible depreciation疲劳损坏周期damage cycle tiredly汽车折旧和残值automobile depreciation and scrap value余额递减法declining balance method变率递减法diminish rates on cost method固定折旧率stationary depreciation rate更新时机优化renewal time optimization自然寿命natural lifespan经济寿命economical lifespan回归分析法regression analysis method劣化数值法deterioration numerical method年当量费用法annual valent weight cost method 更新方式优化update mode optimization汽车技术改造automobile technical innovation 成本分析法cost analysis method建模modeling模拟法simulation method年当量费用valent weight cost per year现值系数present value ratio现值系数present value ratio权重weighing通过性steering ability可靠性security载质量loading weight维修性maintainability设计优化design optimization 行驶路线driven route开式路线open type route单环式路线single ring route多环式路线multi ring route维修网点repairing block单路排队single line queue多路排队multi line queue任务分配task distribution关键路径法critical path method 流线图stream line diagram行列矩阵cortege matrix成本控制cost control最佳工期optimum duration存储优化storage optimization 保管费storage fee利息费interest fee保险费assurance fee损耗费dissipation fee定货费ordering fee手续费handing fee质量成本quality cost检验成本inspection cost预防成本prevention cost典型性原则model principle定量化原则ration principle残值scrap value前拦板front board后拦板rear gate边板side gateU形螺栓U-bolt铰链knuckle5※<标题十>《汽车排放与噪声控制》公害public hazard大气污染air pollution噪声noise生态平衡ecological balance燃料fuel内燃机internal combustion engine 光化学烟雾photochemical smog汽车保有量retain number of automobile 环境保护environment protecting大气检测air detection大气质量标准Air Quality Standard催化剂catalyst汽油机petrol engine柴油机diesel engine氧化反应oxidizing reaction催化反应catalysis reaction还原反应reduction reaction不完全燃烧incomplete combustion 轻型货车pick up truck微型货车minitype truck重型货车heavy truck越野车cross country vehicle驱动轮driven wheel高级轿车limousine特种用途车special used vehicle底盘chassis传动系power train离合器clutch变速器transmission传动轴transmission shaft万向传动装置universal driven device 驱动桥driving axle行驶系going system车架frame前桥front axle驱动桥driving axle后桥rear axle转向轮steering wheel驱动轮driving wheel前悬架front suspension后悬架back suspension转向系steering system方向盘joystick转向器diverter制动系brake system制动装置braking device车身car body电气设备electric equipment电源power点火系ignition system起动系starting system照明设备lighting device信号设备signaling equipment用电设备consumer活塞行程piston stroke压缩比compression ratio工作循环working cycle充量系数coefficient of charge进气input压缩过程compression燃烧膨胀expand排气exhausting可燃混合气carbureted mixture曲柄连杆机构crank link mechanism 配气机构valve mechanism燃料供给系fuel providing system 冷却系cooling system汽缸cylinder配气相位valve timing凸轮cam充气效率charge efficiency空气滤清器Air Filter空燃比Air-Fuel Ratio混合气浓度mixture strength燃料消耗量fuel consumption润滑系lubrication system润滑油lubricating oil燃烧室combustion chamber有效转矩effective torque有效功率effective power后备功率reserve capability负荷特性load characteristic万有特性universal characteristic大气压力air pressure真空度degree of vacuum怠速idle化学平衡chemical equilibrium点火提前角ignition advance angle大气湿度atmospheric humidity废气再循环Exhaust Gas Recirculation涡流vortex稀薄燃烧lean combustion气门重叠角valve overlap angle电子控制汽油喷射Electronic Fuel Injection 压力传感器Sensor空气流量计air flow meter紊流发生罐turbulence generating pot液体代用燃料liquid fuel substitute气体代用燃料gas fuel substitute后处理装置after treatment device三元催化反应器Three Way catalysts烟度limit of smoke消烟添加剂additive机内净化internal purification声强sound intensity声级计sound level meter消声器muffler烟度计smoke meter声压sound pressure定容取样法Constant V olume Sampling欧洲经济委员会Economic Commission for Europe欧洲经济共同体European Economic Community汽车排气净化automobile exhaust gas purification环境调节与自净能力environment adjustment and self-purification ability世界环境卫生经济合作与发展组织World Environment Health Organization for Economic Cooperation and Development汽车污染物排放标准Exhaust Standard for automobile pollution 催化净化装置catalysis and purification device活塞式内燃机piston type internal combustion engine中型客车Medium-sized passenger train发动机工作容积engine working volume四冲程内燃机four stroke internal combustion engine速度特性speed characteristic发动机外特性engine external characteristic电子控制点火系统Electronic Ignition System复合涡流控制燃烧compound vortex controlled combustion 程序化燃烧过程programmed combustion process曲轴箱强制通风系统Position Crankcase V entilatio废气涡轮增压技术exhaust turbo charging technique频带与频谱分析frequency band and spectrum analysis5※<标题十一>《汽车可靠性设计》事件event随机事件random event概率probability随机变量variant分布函数distribute function中位数median众数mode抽样samplingF检验F-test方差variance平均故障时间间隔MTTF-mean time to failure 平均维修时间间隔MTTR-mean time to repair 缺陷defect互换性interchange ability产品责任product liability可靠性控制reliability control可靠性管理reliability management耐久性durability走合break-in走合期break-in period走合距离break-in mileage环境温度ambient temperature大气压力atmospheric pressure台架试验bed test磨合试验running-in test工况behaviour。
汽车常用英文术语200个
变速器孔罩总成
COVER-HOLE
孔罩
108
Hood
罩
HINGE ASSY-HOOD LH
《汽车常用英文术语200个》
No.
英文全称
英文缩写
中文
示例
示例中文
1
Actuator
ACTR
作动器
ACTR & ELEC CONT ASSY
作动器及电控装置总成
ACTR FR DOOR LOCK LH
左前门执行器
2
Adhere
粘贴
3
Adjust
ADJ
调整
ADJ-SEAT BELT RH
右安全带调节器
发动机罩铰链总成
HINGE ASSY-TRUNK LID
行李箱盖铰链总成
106
Holder
HLDR
夹具、固定物
HLDR-ROD
拉杆保持架
HLDR-RR DOOR SUNSHADE
后门窗遮阳罩保持架
HLDR-SUNVISOR
遮阳板固定挂钩
107
Hole
孔
SEAL-INSP HOLE COVER
检修孔罩密封条
BD
车体
HARN-BODY
车身线束
BODY ASSY-STRG WHEEL
方向盘总成
27
Body Side
B/S
侧围
WELT B/S FR LH
前左车身侧围密封条
B/S OTR RH
右侧围外板
28
Bolt
螺栓
WELD BOLT
焊接螺栓
BOLT-COMPR BRKT
汽车行业常用英语词汇
汽车行业常用英语词汇1. Automobile industry 汽车行业2. Vehicle 车辆3. Automotive 汽车的4. Manufacturer 制造商5. Assembly line 生产线6. Car parts 汽车零部件7. Engine 引擎8. Transmission 变速器9. Suspension 悬挂系统10. Chassis 底盘11. Body shell 车身12. Dashboard 仪表盘13. Steering wheel 方向盘14. Brake 刹车15. Accelerator 加速器16. Gearbox 变速箱17. Exhaust system 排气系统18. Fuel injector 燃油喷射器19. Tire 轮胎20. Battery 电池21. Hybrid vehicle 混合动力车辆22. Electric vehicle 电动车23. Plug-in hybrid vehicle 插电式混合动力车辆24. Autonomous vehicle 自动驾驶车辆25. Fuel efficiency 燃油效率26. Emissions 排放物27. Fuel consumption 燃料消耗量28. Safety 安全性29. Crash test 碰撞测试30. Airbag 安全气囊31. ABS (Anti-lock Braking System) 防抱死制动系统32. GPS (Global Positioning System) 全球卫星定位系统33. Infotainment 信息娱乐系统34. Connectivity 连接性35. Bluetooth 蓝牙36. Satellite radio 卫星广播37. Plug-in charger 充电器38. Maintenance 维修保养39. Oil change 换油40. Tire rotation 轮胎轮换41. Brake pad replacement 刹车片更换42. Service appointment 保养预约43. Car wash 洗车44. Car rental 汽车租赁45. Car dealership 汽车经销商。
100个常用的英语版汽车专业术语
100个常用的英语版汽车专业术语100个常用的英语版汽车专业术语1、Sump n.底壳2、Gallery n.通道3、Passage n.小通道4、Filter n.滤清器5、Lobe n.凸轮6、Atmospheric adj.大气的7、Mesh n.啮合8. Spurt n.喷射9. Glide v.滑行10. Appliance n.器具11. Ramp n.斜坡12. Embed v.使插入,嵌入13. Gauge n.测量仪器14. Plug n.插头,插座15. Grid n.系统网络16. Verge n.边沿17. Visionary n.预言家18. Candidate n.候选人19. Monopoly n.垄断20. Cartel n.联合企业21. Infrastructure n.基础设施22. Paradigm n.范例23. Propulsion n.推进24. Fossil n.矿物25. Interchange n.交换,互换26. Interactive adj.人机对话的27. Spot v.认出28. Zap v.快速传送,迅速移动29. Infotronics n.电子信息学30. On the part of sb 就某人而言31. On the roads 在转变过程中32. bulky adj. 大块的;庞大的33. derive from 取得34. Cabin temperature 驾驶室温度35. Freeway ramp 高速公路匝道36. Automatic pilot 自动驾驶仪37. container n.集装箱38. Propulsion system 推进系统39. Inventory system 盘存系统40. Unraveling adj.散开的41. Subprime adj.次要的42. Mortgage n.抵押;抵押契据43. Prosperity n.繁荣,昌盛44. Meltdown n.熔化45. Financing n.融资;理财46. Crunch n.嘎吱嘎吱的响;摊牌47. Mainstay n.中坚,骨干48. Downturn n.下转;衰退49. Merger n.合并50. BRIC 金砖四国51. Plague n.瘟疫,灾害52. Shrink v.收缩,减少53. Inflated adj.充气的,膨胀的54. Perspective n.眼力;前景55. Adverse adj.相反的;不利的56. Bankruptcy n.破产;无偿付能力57. Export-oriented 出口主导的;外向型的58. Post-Olympic adj.奥运会后的59. Overcapacity n.产能过剩60. Multinational adj.多名族的n.跨国公司61. Marque n.(汽车等)型号;62. Proactively adv.主动地,积极地63. Spur v.刺激,鼓励64. Flexible adj.可变通的,灵活的65. Prudent adj.谨慎的;深谋远虑的66. Macro-economy 宏观经济67. Privatize v.使私有化68. Grim adj.严酷的;不祥的69. To grind into a halt 戛然而止70. to tide over 渡过71. to take a toll 抽去,夺去72. to hit on the brakes 踩刹车;启用制动闸73. per-capita GDP 按人均GDP计算74. freight n.货物;运费75. utilization n.利用76. Hammer n.小锤子77. to conclude 最后;总之78. Tier 1 一级供应商79. Revenue n.财政收入80. Negotiation n.谈判;协商81. commodity n.商品;日用品82. double-digit adj.两位数的;十位数的83. pre-established adj.现有的;现存的84. aluminum n.铝85. refund n.退税,退款86. cast n.铸件87. forge n.锻造88. pinch n.拧;挤压89. offset v.抵消90. turn-over n.营业额,成交量91. commitment n.承担义务92. incentive n.刺激93. lure v.引诱94. allowance n.津贴95. bonus n.补助金96. subsidy n.补贴,津贴97. counterpart n.副本;对手方98. compliance n.按照;依从99. stringent adj.严格的100. disposal n.配置;处理。
汽车行业英语专业词汇
汽车行业英语专业词汇1. Automobile industry - 汽车行业2. Automotive - 汽车的,汽车工业的3. Vehicle - 车辆4. Car - 汽车5. Truck - 卡车/载货车6. SUV (Sport Utility Vehicle) - 运动型多功能车7. Sedan - 轿车8. Hatchback -掀背车/斜背车9. Electric vehicle (EV) - 电动车10. Hybrid vehicle - 混合动力车11. Autonomous vehicle - 自动驾驶车辆12. Fuel efficiency - 燃油效率13. Emissions - 排放物14. Curb weight - 空车重量15. Horsepower (hp) - 马力16. Torque - 扭矩17. Engine - 发动机18. Transmission - 变速器19. Suspension - 悬挂系统20. Steering wheel - 方向盘21. Acceleration - 加速22. Braking system - 制动系统23. Exhaust system - 排气系统24. Fuel tank - 燃油箱25. Battery - 电池26. Tire - 轮胎27. Chassis - 底盘28. Bodywork - 车身29. Assembly line - 流水线30. Manufacturing - 制造业31. Production - 生产32. Quality control - 质量控制33. Supplier - 供应商34. Distribution - 分销35. Sales - 销售36. Marketing - 市场营销37. After-sale service - 售后服务38. Maintenance - 维修保养39. Dealership - 经销商40. Customer - 客户41. Consumer - 消费者42. Market share - 市场份额43. Competitive advantage - 竞争优势44. Brand - 品牌45. Model - 型号46. Price - 价格47. Promotion - 推广48. Advertisement - 广告49. Innovation - 创新50. Research and development - 研发。
《汽车常用英文术语200个》
85 Foot Rest 搁脚板
86 Front FR 前部、前侧
87 Fuel 燃油
88 Fuse 保险丝
89 Garnish GARN 装饰
90 Gasket GSKT 衬垫
91 Gear 齿轮
92 Glass 玻璃
93 Glove Box 资料盒
217 Transmission TRANS 变速箱
218 Trim 内饰
219 Trunk Lid T/L 行李箱盖
220 Tube 金属管
221 Upper UPR 上部
222 Valve 阀、气门
223 Vehicle 车辆、整车
224 Ventilator VENT 出风口
49 Column 柱
50 Compressor COMP 压缩机
51 Condenser CDS 冷凝器
52 Console 杂物盒
53 Control CONT 控制、管理
54 Cooling 冷却
55 Corner 角落
56 Cover 盖
57 Crankshaft CR/SHF 曲轮轴
10 Arm 摇臂
11 Ash Tray 烟灰盒
12 Assembly ASSY 总成、组装
13 Automatic Transmission A/T 自动变速器
14 Axle 车桥、车轴
15 Back 后部、倒车
16 Baggage BAG 行李
17 Balance BAL 平衡
188 Sealing SEAL 密封
189 Seat 座椅
190 Section 科室、截面
汽车专用术语大全(中英文注释)
机油滤清器(Oil filter) 一种在机油通过时便可将污物滤下的装置。
机油泵(Oil Pump) 在润滑系统中,可迫使机油自油底壳送到引擎运动件的装置。
爆声(Ping) 引擎在加速时所产生的爆震现象,此因点火正时提前太多或燃料的辛烷值过低所致。
活塞(Piston) 一种装在汽缸内活动的机件,能在压力改变时接受或传递动力。就引擎而言是指在汽缸内上下滑动,并藉助连杆,迫使曲轴旋转的圆形机件。
齿轮润滑油(Gear Lubricant) 一种可润滑齿轮的机油,通常为SAE90号机油。
热控制阀(Heat-Control Valve) 在引擎排气歧管中一种节温操作阀门,可在引擎未达正常工作温度之前,将废气的热导入进气歧管。
敲击(Knock) 随引擎速度出现的金属撞击声,通常是因轴承松脱或磨损所产生。
动力刹车器(Power-Brake) 以引擎真空及油压操纵Booster等作用补助刹车力量的刹车。
刹车来令(Brake Lining) 刹车蹄片上的制动表面所张贴的摩擦材料,一般大型汽车是以铆钉固定,而小型车则用粘剂加压张贴之。
刹车蹄片(Brake Shoes) 受刹车凸轮或推杆的作用量被推向外展开压制刹车鼓,而起制动作用的配件,其形状似如半月形。
飞轮(Flywheel) 装置在曲柄轴的一端,是铸铁制造较重的轮盘,在爆发冲程传递回转力,由飞轮一时吸收储蓄,供给在下次动力冲程,能使曲柄轴圆滑回转作用,外环的齿环可供起动时摇转引擎之用,背面与离合器片接触,成为离合器总成的组件。
离合器片(Clutch Disc, Clutch) 作为传递引擎动力到变速箱的媒介物。
活塞梢(Piston Pin) 一种管状的金属块,可将活塞或连杆连接。
汽车专业英语术语汇总(复习资料)
UNIT 1 AUTOMOTIVE BASICS Body:车身chassis:底盘stream-lined:流线wind resistance:风阻Frame:车架the power train:传动系统the drive train:驱动系a unitized body:承载式车身unibody:整体式汽车车身suspension system:悬架系统steering system:转向系统braking system(制动系统) suspension system:悬架系统shock absorber:减振器control arm:控制臂、导向机构steering gears:转向器steering wheel:转向盘idler arm:随动臂tie rods:横拉杆power steering:动力转向Power booster:助力器master cylinder:制动主缸Disc brake:盘式制动drum brake:鼓式制动Brake pedal:制动踏板brake system:制动系统stopping power:制动力Hydraulic brakes:液压制动brake pedal:制动踏板brake fluid:制动液brake lines:制动管路cylinders:轮缸brake shoes:制动蹄drum:制动鼓disc brake:盘式制动器pliers:老虎钳squeeze:挤进,握紧;夹紧rotating disc:旋转制动盘Drum brake:鼓式制动器gasoline-burning piston engine:活塞式汽油发动机Diesel-fuel burning engines:柴油发动机Fuel system:供给系统exhaust system:排气系统Cooling system:冷却系统lubrication system:润滑系统ignition system:点火系统electric spark:电火花air-fuel mixture:可燃混合气cylinder:汽缸ignition switch:点火开关current:电流storage battery:蓄电池ignition coil:点火线圈Distributor:分电器spark plug:火花塞compression ignition engines:压燃式发动机charging circuit:充电电路regulator:电压调节器alternator (or generator):发电机mechanical energy:机械能electrical energy:电能maximum voltage:最大电压fuel system:燃料供给系统fuel pump:燃油泵Filter:滤清器carburetor:化油器fuel injection system:燃油喷射系统combustible mixture:可燃混合气manifold:进气管exhaust system:排气系统carbon monoxide:一氧化碳hydrocarbons(碳氢化合物)oxides of nitrogen:氮氧化合物emission control system:排放控制系统cooling system:冷却系统combustion chamber:燃烧室coolant:冷却液Radiator:散热器water pump:水泵hollow:空的、空洞的block:汽缸体head:汽缸盖Defroster:(除冰(或霜)装置) Lubrication system润滑系统lubricant:润滑剂piston rings:活塞环cylinder walls:汽缸壁oil filter:机油滤清器Transmission:变速器wheel bearings:车轮轴承differential:差速器steering linkage:转向链接机构power train:传动系统transmission:变速器shift lever:变速杆clutch:离合器Transmission:变速器torque:转矩Differential:差速器drive /propeller shaft:传动轴universal joints:万向节axle movement:轴向运动flexible universal joints:活动万向节Differential:差速器UNIT 2 AUTOMOTIVE ENGINEinternal combustion engine:内燃机liquefied petroleum gas(LPG):液化石油气Compressed natural gas(CNG):压缩天然气drive shaft:驱动轴rear-wheel-drive arrangement:后轮驱动布置形式front-wheel-drive arrangement:前轮驱动布置形式drive wheels:驱动轮mid-engine arrangement:发动机中置Pistons:活塞reciprocate:往复spark ignition engine:火花点燃式发动机compression ignition(CI) engine:压燃式发动机electric ignition system:电子点火系统spark plug:火花塞ignite:点燃cylinders:气缸combustion:燃烧compression-ignition engine:压燃式发动机diesel engine:柴油机Spray:喷入heavy-duty trucks:重型货车spark-ignition engine:火花点燃式发动机fuel system:燃料供给系统ignition system:点火系统lubricating system:润滑系统cooling system:冷却系统fuel system:燃料供给系统combustible mixture:可燃混合物air/fuel mixture:空气燃料混合气ignition system:点火系统spark plug:火花塞air/fuel mixture:可燃混合气lubricating oil:润滑油lubricating system:润滑系统oil pump:机油泵reservoir:贮存器; 油箱exhaust gas:排气cooling system:冷却系统exhaust system:排气系统emission-control system:排放控制系统starting system:启动系统Crank:转动曲柄starting motor:启动马达internal combustion engine:内燃机chemical energy:化学能heat energy:热能mechanical energy:机械能air/fuel ratio:空燃比Diesel engines:柴油机intake:进气connecting rod:连杆crankshaft:曲轴reciprocating movement/back and forth movement/up and down movement(往复运动) rotary motion/ turning motion:(旋转运动) crankshaft:曲轴Efficiency:效率potential energy:潜能mechanical energy:机械能overall efficiency:总效率compression ratio:压缩比air/fuel ratio:空燃比uppermost position/(TDC, top dead center:上止点lowest position/BDC, bottom dead center:下止点stroke:行程four stroke-cycle Gasoline Engine: intake stroke:进气行程compression stroke:压缩行程power stroke:作功行程exhaust stroke:排气行程revolution:转、圈connecting rod:连杆intake valve:进气门camshaft:凸轮轴pressure difference:压力差air/fuel mixture:空气/燃料混合气compression ratio:压缩比TDC:上止点exhaust valve:排气门exhaust gases:废气starter motor:启动马达ignition key:点火钥匙start position:启动位置Flywheel:飞轮UNIT 3 AUTOMOTIVE LUBRICATION SYSTEM (汽车润滑系统) 3.1 Lubrication Principles 润滑原理Friction:摩擦primary job:基本任务Residual oil:残留的机油Lubricant:滑润剂hydrodynamic:液力的oil adhesion:机油粘度sliding friction:滑动摩擦Pressure-Lubrication System压力润滑系统oil pan:油底壳block:汽缸体oil pump:油泵drain plug:放油螺塞oil-pan gasket:油底壳垫圈Passageway:油道oil filter:机油滤清器Crankcase:曲轴箱tube:管filter screen:滤网gear-type:齿轮泵rotor-type:转子泵full-flow filtering system:全流式滤清器pressure-relief valve:安全阀bypass valve:旁通阀camshaft(凸轮轴)main bearing:主轴承camshaft bearing:凸轮轴轴承Foam inhibitor:泡沫抑制剂UNIT 4 THE COOLING SYSTEM(冷却系统) exhaust system:排气系统cylinder wall:汽缸壁piston:活塞cylinder head:汽缸盖oil film:油膜fuel mileage:燃油经济性exhaust emissions:废气排放liquid cooling:水冷air cooling:风冷water jacket:水套thermostat:节温器water pump:水泵radiator:散热器radiator cap:散热器盖cooling fan:冷却风扇hoses:软管expansion tank:膨胀水箱overflow tank:溢流水箱4.1 Water Pump(水泵)centrifugal pump:离心泵centrifugal force:离心力4.2 Water Jacket(水套)hot spot:热点valve seat:气门座valve guide:气门导管cylinder wall:汽缸壁combustion chamber:燃烧室4.3 Radiator(散热器)heat exchanger:热交换器4.4 Pressure Cap(散热器盖)boiling point:沸点pressure release valve:减压阀, 安全阀overflow tube:溢流管overflow tank:溢流箱4.5 Thermostat(节温器)4.6 Fancooling fan:冷却风扇constant temperature:常温thermostatic switch:温控开关UNIT 5 FUEL INJECTION SYSTEMFuel injection system:燃油喷射系统purely mechanical:纯机械的electronic fuel injection system:电子燃油喷射系统feedback control:反馈控制emission:排放solenoid valve:电磁阀injector:喷油器best power:最佳动力性best emission:最佳排放性best economy:最佳经济性rich condition:浓(混合气)工况lean condition:稀(混合气)工况5.3 Fuel System(燃油系统)fuel rail:油轨regulator:压力调节器return line:回油管fuel manifold:燃油歧管intake manifold:进气歧管5.4 Air Metering and Measurement 空气计量butterfly valve:传统碟形阀throttle body assembly:节气门体总成Mass Airflow:质量流量Speed Density:速度密度spring loaded flap:翼片potentiometer:电位计heated wire:加热电阻丝voltage signal:电压信号5.5 Most EFI systems measure the same basic 6 input 大多数EFI系统检测6个基本输入(信号)RPM(转速)ignition coil:点火线圈magnetic sensor:磁脉冲传感器Hall effect sensor:霍尔效应传感器Manifold Pressure (进气歧管压力)Throttle Position (节气门位置)Water Temperatureinjector pulse width:喷油器脉冲宽度Air Temperature5.6 Oxygen Sensor(氧传感器)closed loop systems:闭环系统oxygen content:氧含量air/fuel ratio:空燃比open loop mode:开环模式UNIT 6 EXHAUST SYSTEMexhaust system:排气系统Exhaust gas:废气combustion chamber:燃烧室muffler:消声器catalytic converter:催化转换器6.2 The Muffler(消声器)backpressure:背压exhaust valve:排气门6.3 The Exhaust Manifold and Headerexhaust manifold:排气歧管cylinder head:气缸盖intake manifold:进气歧管UNIT 7 THE IGNITION SYSTEM(点火系统) breaker point type ignition system:触点型点火系统electronic ignition system:电子点火系统distributorless ignition system: 无分电器点火系统)timing of the spark plug firing: 火花塞点火次序spark plug gap:火花塞间隙7.1 Point-Type Ignition System (触点型点火系统)electrical circuit:电路primary circuit:初级回路secondary circuit:次级回路breaker point:触点ignition switch:点火开关secondary winding:次级线圈high-tension lead:高压导线distributor:分电器coil:点火线圈distributor cap:分电器盖distributor rotor:分火头controlling element:控制元件primary current:初级电流Distributor:配电器7.2 Electronic Ignition Systems(电子点火系统)electronic control module:电子控制模块7.3 Distributorless Ignition Systems (DIS) (无分电器点火系统)spark timing:点火正时Ignition Control Unit (ICU):点火控制单元Engine Control Unit (ECU):发动机控制单元firing order:点火顺序Top Dead Center (TDC):上止点UNIT 8 CLUTCHdrive line/drive train:传动系统Clutch:离合器transmission:变速器drive shaft:传动轴final drive assembly:主减速器总成clutch disc:离合器片pressure plate:压盘pressure plate cover:离合器盖friction mechanism:摩擦机构engine torque:发动机扭矩gear ratio:传动比clutch pedal:离合器踏板driven member:从动件transmission input shaft:变速器输入轴driving members:主动件crankshaft:曲轴torsional shock:扭转振动starter motor:启动马达splined hub:花键毂spline:花键diaphragm spring:膜片弹簧centrifugal force:离心力release bearing:分离轴承disengagement mechanism:分离机构hydraulic system:液压系统hydraulic mechanism:液压机构clutch master cylinder:离合器主缸hydraulic fluid:制动液clutch release cylinder:离合器分离缸UNIT 9 AUTOMATIC TRANSMISSION(自动变速器)fluid coupling(液力偶合器)torque converter(变矩器rear wheel drive(后轮驱动)front wheel drive(前轮驱动).drive shaft(驱动轴)final drive(主减速器)rear axle(后轴)rear wheels(后轮)transaxle(驱动桥)Front axles(前桥)planetary gear sets(行星齿轮组) 9.1hydraulic system(液力系统)9.2Planetary gear sets(行星齿轮组)sun gear(太阳轮)ring gear(齿圈)planet gears(行星轮)constant mesh(常啮合common carrier(行星架)input shaft(输入轴)output shaft(输出轴)9.2 Clutch pack(离合器组)clutch drum(离合器鼓)friction material(摩擦材料)9.3 One-Way Clutch(单向离合器)"sprag" clutch(超越离合器)neutral(空挡)9.4 Bands(制动带)9.5 Torque Converter(液力变矩器)(见阅读材料)Torque Converter(液力变矩器)manual transmission:自动变速器automatic transmission:自动变速器brake pedal:制动踏板gas pedal:加速踏板1. Pump(泵轮).2. Turbine(涡轮).3. Stator(导轮).4. Transmission fluid(传动液). Freewheel:自由轮lockup clutch:锁止离合器UNIT 10 THE DIFFERENTIAL(差速器) unlimited-slip, differential:不防滑差速器10.1 The Main Gears(主减速器)bevel gear:锥齿轮axle shaft:半轴final drive assembly:主减速器总成gear reduction:减速drive wheel:驱动轮drive shaft:传动轴spiral bevel gear:螺旋锥齿轮center line(centerline):中心线10.2 The Differential System(差速系统) axle shaft:半轴side gear:半轴齿轮UNIT 11 BRAKE SYSTEM(制动系统) kinetic energy:惯性能量momentum:动量thermal energy (heat):热能master cylinder:主缸brake pedal:制动踏板mechanical pressure:机械压力hydraulic pressure:液体压力brake line:制动管brake hose:制动软管slave cylinder:轮缸Brake fluid:制动液Shoe:制动蹄pad:制动块drums:制动鼓rotor:制动盘disk brake:盘式制动器drum brakes:鼓式制动器caliper:制动嵌brake shoe:制动蹄friction lining:摩擦衬片friction surface:摩擦表面emergency brake:紧急制动Power brake booster:动力制动助力器master cylinder:制动主缸brake pedal:制动踏板hydraulic actuator:液压传动机构wheel speed sensor:车轮速度传感器UNIT 14 ABS AND TCS14.1 Braking System Fundamentals, master cylinder:主缸wheel cylinders:轮缸caliper pistons:制动钳活塞rolling energy:旋转能量14.2 Antilock Braking Systems(防抱死制动系统)retarding force:制动力percent slip滑移率braking effectiveness:制动效能wheel speed sensors (WSS):车轮速度传感器。
汽车英文术语
CYL CR/SHF CAM
LUB BRG
FLG
ADJ BAG BOOS BRK BMPR
HBRK
H/RST
IP INSUL P/S RAD REG
SEPA
COMP CDS
P4/4
序号 英文全称 Console 40 Cooling 41 Defroster 42 Device 43 Disc 44 Drive 45 Emission 46 Exhaust 47 Fan 48 Jack 49 Key 50 Knob 51 Lock 52 Manifold 53 Mirror 54 Muffler 55 Nozzle 56 Pad 57 Paddle 58 Parking Brake 59 Patch 60 Steering 61 Sunvisor 62 Support 63 Suspension 64 Tire 65 Tool-Set 66 Ventilator 67 Wind Shield 68 Washer 69 Canister 70 link 71 七、其它术语 Trim 1 Chassis 2 Assembly 3 Subordinate 4 Press 5 Weld 6 Paint 7 Balance 8 Batch Number 9 Final Check 10 Road Test 11 Guage 12 Joint Check 13 Quality Assurance 14 Quality Control 15 Quality Improvement 16 Repair 17 Reset 18 Return 19 Control 20 Department 21 Section 22 Manufacturning 23 Package 24 Specification 25 Speed 26 Temperature 27 Part 28 Vehicle 29 英文缩写 杂物盒 冷却 除霜器 装置、设备 碟 驱动、架驶 排放 排气 风扇 千斤顶 钥匙、键 手柄 锁 歧管、支管 镜子 消音器 管口、喷嘴 垫、板 踏板 驻车制动 补钉 转向 遮阳板 支架 悬挂 轮胎 随车工具 出风口 挡风(玻璃) 中文 原序号 52 54 61 63 64 67 70 73 75 119 121 123 130 134 139 143 144 150 151 153 155 202 207 208 209 214 215 224 229 225 39 129 218 44 12 205 165 226 152 17 19 79 184 96 120 169 170 171 179 180 181 53 62 190 136 149 197 198 213 154 223
汽车常用英文术语200个
EXH EXTR FDR
排气 外装 风扇 防护板、翼子板
77 Filler
加注口
78 Filter 79 Final Check 80 Finisher
F/C FIN
滤清器 终检 饰板
DRIP-FDR FDR-FR STAY ASSY-FR FDR TUBE ASSY-FILLER BASE-FUEL FILLER BMPR-FUEL FILLER HLDR FUEL FILTER FIN ASSY-RR PLR LH FIN-HUD FIN-INST A ROD-BATFIX SCR-FIX STRG LOCK FLG-AIR INT FLOOR SIDE ASSY-RR LH FLOOR-FR
示例中文
除霜器导管 驻车装置总成 变速操纵杆总成 铝合金轮辋 前制动盘 抬头显示装置 左前门总成 车门护块 门内把手饰盖 驱动轴总成 作动器及电控装置总成 排放软管 后端 前端 发动机支架 发动机舱线束 发动机安装减震垫 排气管支架
62 Department 63 Device 64 Disc 65 Display 66 Door
搁脚板支架 前门上铰链总成 前制动盘 油箱管护板 供油软管 保险丝盒盖总成 保险丝夹 左中立柱下饰板 行李箱上饰板 制动管衬垫 密封垫圈 动力转向机总成 前风窗玻璃总成 后挡风玻璃 左三角玻璃 资料盒盖总成 散热器格栅总成
93 Glove Box 94 Grill
资料盒 格栅
P4/8 No.
95 96 97 98 99 100
翼子板滴水檐 前翼子板 前翼子板支撑板总成 加油管总成 加油基座 加油口盖减振胶垫 滤清器支架 左后立柱装饰板 抬头显示器饰板总成 左仪表板饰板 蓄电池固定拉杆 点火锁螺钉 进气法兰 左后地板侧板 前地板
汽车术语中英文对照
以下是一些常见的汽车术语中英文对照:1. 引擎 Engine2. 变速器 Transmission3. 刹车系统 Brake System4. 悬挂系统 Suspension System5. 轮胎 Tires6. 方向盘 Steering Wheel7. 安全带 Seat Belt8. 空调系统 Air Conditioning System9. 油箱 Fuel Tank10. 引擎盖 Engine Hood11. 保险杠 Bumper12. 车门 Door13. 座椅 Seat14. 仪表盘 Instrument Panel15. 引擎管理系统 Engine Management System16. ABS防抱死刹车系统 Anti-lock Brake System17. ESP车身稳定系统 Electronic Stability Program18. CVT无级变速器 Continuously Variable Transmission19. DSG双离合器变速器 Double-Clutch Transmission20. V6发动机 6-cylinder Engine21. Wagon旅行车 Estate Car22. Coupe轿跑车 Coupe23. SUV运动型多功能车 Sport Utility Vehicle24. Pickup皮卡 Pickup Truck25. Minivan小型货车 Multi-Purpose Vehicle (MPV)26. Roadster跑车 Roadster27. Sedan轿车 Saloon Car28. Station Wagon箱型车 Estate Car29. Hatchback掀背式车 Hatchback30. Convertible敞篷车 Convertible31. Off-Road越野车 Off-Roader32. Hybrid混合动力车 Hybrid Vehicle33. Electric电动车 Electric Vehicle34. Turbo涡轮增压车 Turbocharged Vehicle35. Sport运动版车 Sport Model36. Luxury豪华版车 Luxury Model。
汽车常用英文术语
汽车常用英文术语——你能知道几个!汽车常用英文术语简述:1.ABS:“ABS”是英文“Anti-lockBreakSystem”的缩写,中文译为“防死锁刹车系统”。
它是一种具有防滑、防锁死等优点的安全刹车控制系统。
2.OBD:OBD是英文On-Board Diagnostics的缩写,中文翻译为“车载自动诊断系统”。
这个系统将从发动机的运行状况随时监控汽车是否尾气超标,一旦超标,会马上发出警示。
3.ASR:ASR是驱动防滑系统的简称,其作用是防止汽车起步、加速过程中驱动轮打滑,特别是防止汽车在非对称路面或转弯时驱动轮空转,并将滑移率控制在10%—20%范围内。
4.ECU:ECU是汽车上的计算机控制系统,燃油经济性、ABS启动的及时性、车上所有电器系统的控制都由ECU实现,在现代汽车中,ECU的先进性,一定程度上标志着产品的年代差别。
5. Turbo:涡轮增压简称Turbo,如果在轿车尾部看到Turbo或者T,即表明该车采用的发动机是涡轮增压发动机。
6. OHC:发动机的凸轮轴安装位置有下置、中置、顶置三种形式。
按凸轮轴数目的多少,可分为单顶置凸轮轴(SOHC)和双顶置凸轮轴(DOHC)两种,由于中高档轿车发动机一般是多气门及V型气缸排列,需采用双凸轮轴分别控制进排气门,因此双顶置凸轮轴被不少名牌发动机所采用。
7.VTEC:VTEC系统全称是可变气门正时和升程电子控制系统,是本田8.MPV:MPV的全称是Multi-Purpose Vehicle,即多用途汽车。
它集轿车、旅行车和厢式货车的功能于一身。
8.LSD:LSD-Limited Slip Differential限滑差速器, LSD为循迹控制的一环可以确保驱动轮的动力输出, 常用于后轮驱动车的后轴差速器上,9.SUV:SUV的全称是SportUtility Vehicle,中文意思是运动型多用途汽车。
现在主要是指那些设计前卫、造型新颖的四轮驱动越野车。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
CTR CHAS
ASSY A/T
COMP CDS CONT
BAG BAL BATNO BAT BRG
CR/SHF CYL CYL DEF DEPT DVC DISP DR ELEC ELEK EMIS ENG EXH EXTR FDR J/C
BD B/S BOOS
BRKT BRK BMPR
CAM
F/C FIN FLG
LH
FR
GARN Leabharlann SKTLWR LUB MBR MFO M/T MFG
GROM
P2/2
序号
96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196
序号
39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137
H/RST
HLDR
OP OTR PACK PADL PKB
IG INR IP INSUL INT INTR
PLR
SPEC SPD SPR STRG
P/S PROTR
QA QC QI RAD RR REG REINF REP RTN RH
SUB S/R SUPT SUSP SW
TEMP
TRANS T/L UPR
英文缩写
HBRK HARN
中文
检具 防溅 手刹 听筒、手柄 线束 大灯 顶篷 头枕 加热器 绞链 夹具、固定物 孔 罩 挂钩 喇叭 软管 轮毂 点火 内部、内板 仪表板 绝缘层、隔热垫 进(气)口 内装 袋 点 电动、动力 动力转向 冲压 保护器 把手 泵 品质保证 品质管理 品质提升、品质改善 水箱 音响 后部、后侧 接受器 调节器 加强件 继电器 修理 复位 复位、返回 右侧 圈 路试 撑杠 顶盖 螺丝 密封 座椅 科室、截面 换挡 传感器 分离器 垫块 备用轮胎 扬声器
P1/2
《汽车常用英文术语200个》
序号
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95
序号
138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232
英文全称
Meter Mirror Molding Motor Mounting Muffler Nozzle Nut Oil Openning Outer Package Pad Paddle Paint Parking Brake Part Patch Pillar Pin Pipe Plane Plug Specification Speed Sponge Spring Starter Steering Stopper Strip Subordinate Sun Roof Sunvisor Support Suspension Switch Tail Tank Temperature Tire Tool-Set Top Transmission Trim Trunk Lid Tube Upper Valve Vehicle Ventilator Washer Weld Welt Wheel Wind Shield Window Wiper Grille
英文全称
Actuator Adhere Adjust Air Bag Air Conditioner Alarm Alternator Antenna Anti-lock Brake System Arm Ash Tray Assembly Automatic Transmission Axle Back Baggage Balance Bar Batch Number Battery Bearing Belt Blade Block Blower Body Body Side Bolt Booster Bow-Roof Box Bracket Brake Bumper Bushing Buzzer Cable Camshaft Filler Filter Final Check Finisher Fix Flange Floor Fluid Foot Rest Front Fuel Fuse Garnish Gasket Gear Glass Glove Box Grill Grommet
英文全称
Guage Guard-Splash Hand Brake Handset Harness Head Lamp Head Lining Head Restraint Heater Hinge Holder Hole Hood Hook Horn Hose Hub Ignition Inner Instrument Panel Insulator Intake Interior Pocket Point Power Power Steering Press Protector Pull Handle Pump Quality Assurance Quality Control Quality Improvement Radiator Radio Rear Receiver Regulator Reinforce Relay Repair Reset Return Right Hand Ring Road Test Rod Roof Screw Sealing Seat Section Selector Sensor Separator Spacer Spare Wheel Speaker
SCR SEAL
VENT WASH
SEN SEPA
WHL W/S WDW WIP
英文全称
Canister Cap Carpet Caution Center Chassis Clamp Cleaner Clip Clutch Column Compressor Condenser Console Control Cooler Corner Cover Crankshaft Cycle Cylinder Dash Defroster Department Device Disc Display Door Drive Electrical Electronic Emission End Engine Exhaust Exterior Fan Fender Jack Joint Check Key Kit Knob Label Lamp Left Hand Lid Line link Lock Lower Lubrication Main Bolster Manifold Manual Transmission Manufacturning Metal
英文缩写
MLDG MTG MFLR
中文
仪表 镜子 模制、模塑、注塑 电机、汽车 安装 消音器 管口、喷嘴 螺母 机油 开 外部、外板 包装 垫、板 踏板 油漆、涂装 驻车制动 部品 补钉 立柱 销、针、钉 硬管 面 堵塞 规范 速度 海棉 弹簧 起动机 转向 挡块 密封条、带 辅助、分总成、分装 天窗 遮阳板 支架 悬挂 开关 尾 箱、罐 温度 轮胎 随车工具 顶部 变速箱 内饰 行李箱盖 金属管 上部 阀、气门 车辆、整车 出风口 垫片 焊接 边、条 轮、盘 挡风(玻璃) 车窗 雨刮 栅栏
英文缩写
ACTR ADJ AB A/C ALTN ANT ABS
中文
作动器 粘贴 调整 气囊 空调 警报 发电机 天线 防抱死制动系统 摇臂 烟灰盒 总成、组装 自动变速器 车桥、车轴 后部、倒车 行李 平衡 杠、条 批号 蓄电池 轴承 皮带 刮片 缸体 鼓风机 车体 侧围 螺栓 真空助力器 顶盖中弓形梁 盒 支架 制动器 保险杠、减振垫 衬套 封鸣器 电缆、拉索 凸轮轴 加注口 滤清器 终检 饰板 固定 凸缘、法兰 地板 液、油 搁脚板 前部、前侧 燃油 保险丝 装饰 衬垫 齿轮 玻璃 资料盒 格栅 垫圈、金属孔眼
英文缩写
中文
碳罐 帽、盖 地毯 警示 中心、中央 底盘 卡箍、喉箍 清洁器 卡扣、夹子 离合器 柱 压缩机 冷凝器 杂物盒 控制、管理 冷却 角落 盖 曲轮轴 环 气缸 前围 除霜器 部门 装置、设备 碟 显示 门 驱动、架驶 电器的 电子的 排放 端部 发动机 排气 外装 风扇 防护板、翼子板 千斤顶 联合检查 钥匙、键 包 手柄 标签 灯 左侧 盖子 线 连接、连杠 锁 下部 润滑 纵梁 歧管、支管 手动变速器 制造 金属、钣金