PCB工艺术语

* Process Module 说明:

A. 下料( Cut Lamination)

a-1 裁板( Sheets Cutting)

a-2 原物料发料(Panel)(Shear material to Size) B. 钻孔(Drilling)

b-1 内钻(Inner Layer Drilling )

b-2 一次孔(Outer Layer Drilling )

b-3 二次孔(2nd Drilling)

b-4 雷射钻孔(Laser Drilling )(Laser Ablation )

b-5 盲(埋)孔钻孔(Blind & Buried Hole Drilling) C. 乾膜制程( Photo Process(D/F))

c-1 前处理(Pretreatment)

c-2 压膜(Dry Film Lamination)

c-3 曝光(Exposure)

c-4 显影(Developing)

c-5 蚀铜(Etching)

c-6 去膜(Stripping)

c-7 初检( Touch-up)

c-8 化学前处理,化学研磨( Chemical Milling )

c-9 选择性浸金压膜(Selective Gold Dry Film Lamination)

c-10 显影(Developing )

c-11 去膜(Stripping )

D. 压合Lamination

d-1 黑化(Black Oxide Treatment)

d-2 微蚀(Microetching)

d-3 铆钉组合(eyelet )

d-4 叠板(Lay up)

d-5 压合(Lamination)

d-6 后处理(Post Treatment)

d-7 黑氧化( Black Oxide Removal )

d-8 铣靶(spot face)

d-9 去溢胶(resin flush removal)

E. 减铜(Copper Reduction)

e-1 薄化铜(Copper Reduction)

F. 电镀(Horizontal Electrolytic Plating)

f-1 水平电镀(Horizontal Electro-Plating) (Panel Plating) f-2 锡铅电镀( Tin-Lead Plating ) (Pattern Plating)

f-3 低於1 mil ( Less than 1 mil Thickness )

f-4 高於1 mil ( More than 1 mil Thickness)

f-5 砂带研磨(Belt Sanding)

f-6 剥锡铅( Tin-Lead Stripping)

f-7 微切片( Microsection)

G. 塞孔(Plug Hole)

g-1 印刷( Ink Print )

g-2 预烤(Precure)

g-3 表面刷磨(Scrub)

g-4 后烘烤(Postcure)

H. 防焊(绿漆): (Solder Mask)

h-1 C面印刷(Printing Top Side)

h-2 S面印刷(Printing Bottom Side)

h-3 静电喷涂(Spray Coating)

h-4 前处理(Pretreatment)

h-5 预烤(Precure)

h-6 曝光(Exposure)

h-7 显影(Develop)

h-8 后烘烤(Postcure)

h-9 UV烘烤(UV Cure)

h-10 文字印刷( Printing of Legend )

h-11 喷砂( Pumice)(Wet Blasting)

h-12 印可剥离防焊(Peelable Solder Mask)

I . 镀金Gold plating

i-1 金手指镀镍金( Gold Finger )

i-2 电镀软金(Soft Ni/Au Plating)

i-3 浸镍金( Immersion Ni/Au) (Electroless Ni/Au) J. 喷锡(Hot Air Solder Leveling)

j-1 水平喷锡(Horizontal Hot Air Solder Leveling) j-2 垂直喷锡( Vertical Hot Air Solder Leveling)

j-3 超级焊锡(Super Solder )

j-4. 印焊锡突点(Solder Bump)

K. 成型(Profile)(Form)

k-1 捞型(N/C Routing ) (Milling)

k-2 模具冲(Punch)

k-3 板面清洗烘烤(Cleaning & Backing)

k-4 V型槽( V-Cut)(V-Scoring)

k-5 金手指斜边( Beveling of G/F)

L. 短断路测试(Electrical Testing) (Continuity & Insulation Testing) l-1 AOI 光学检查( AOI Inspection)

l-2 VRS 目检(Verified & Repaired)

l-3 泛用型治具测试(Universal Tester)

l-4 专用治具测试(Dedicated Tester)

l-5 飞针测试(Flying Probe)

M. 终检( Final Visual Inspection)

m-1 压板翘( Warpage Remove)

m-2 X-OUT 印刷(X-Out Marking)

m-3 包装及出货(Packing & shipping)