常用塑料词汇
塑料制品企业常用的英语词汇
七．QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan，产品质量先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析MSA Measure System Analysis,测量系统分析SPC Statistical Process Control,统计过程控制审核Audit能力Capability能力指数Capability Indices控制计划Control Plans纠正措施Corrective Action文件Documentation作业指导书Job Instruction, work instruction 不合格品Nonconformance不合格Nonconformity每百万零件不合格数Defective Parts Per Million, DPPM预防措施Preventive Action程序Procedures过程流程图Process Flow Diagram, Process Flow Chart质量手册Quality Manual质量计划Quality Plan质量策划Quality Planning质量记录Quality Records原始数据Raw Data反应计划Reaction Plan返修Repair。
返工Rework现场Site分承包方Subcontractors产品product质量quality质量要求quality requirement顾客满意customer satisfaction质量管理体系quality management system质量方针quality policy质量目标quality objective 质量管理quality management质量控制quality control质量保证quality assurance组织organization顾客customer供方supplier过程process服务service设计与开发design and development：特性characteristic可追溯性trace ability合格conformity缺陷defect纠正correction让步concession放行release报废scrap规范specification检验inspection试验test验证verification评审review测量measurement计数型数据Attributes Data普通原因Common Cause单值Individual均值Mean随机抽样Random Sampling极差Range特殊原因Special Cause稳定性Stability子组Subgroup计量型数据variables Data变差variation固有变差Inherent variation总变差Total variation偏倚Bias重复性Repeatability再现性Reproducibility稳定性Stability线性Linearity分辨率Resolution过程更改Process change质量功能展开QFD过程特殊特性Special Process Characteristic 产品特殊特性Special Product Characteristic 外观项目Appearance Item初始过程能力Preliminary Process Capability 材料清单Bill of Material设计确认Design Validation设计验证Design Verification顾客的呼声Voice of the Customer过程的呼声Voice of the Process八．常用缩略词语1、ES 工程规范Engineering Specification2、KCC 关键控制特性（GM）Key Control Characteristic3、KPC 关键产品特性（GM）Key Product Characteristic4、OEM 整车厂Original Equipment Manufacturer5、SC重要(特殊)特性Significant(Special) Characteristic6、ANOVA 方差分析法Analysis of variance7、CFT 多方论证小组Cross function Team8、DFMEA 设计失效模式及后果分析Design Failure Mode and Effects Analysis9、DOE 试验设计Design of Experiment10、DVP&R 设计验证计划和报告Design verification Plan and Report11、FTC 试生产能力First Time Capability12、GR&R 量具的重复性和再现性Gage Repeatability and Reproducibility13、PFMEA 过程失效模式及后果分析Process Failure Mode and Effect Analysis 14、SFMEA 系统失效模式及后是分析System Failure Mode and Effect Analysis 15、QSR 质量体系要求Quality System Requirement16、QFD 质量功能展开Quality function Deployment17、TGR 运行情况良好Things Gone Right18、TGW 运行情况不良Things Gone Wrong19、VE/VA 价值工程/价值分析Value Engineering/Value Analysis20、BOM 物料清单Bill of Material21、Cpk 稳定过程的能力指数Capability for stable process22、LCL 下控制限Lower Control Limit23、UCL 上控制限Upper Control Limit24、LSL 工程规范下限Lower Specification Limit25、USL 工程规范上限Upper Specification Limit26、Ppk 性能指数The performance index27、MRB 物料评审Material Review Board28、PSW 零件提交保证书Part Submission Warrant29、X(—)--R图均值一极差图Average-Range Chart30、SRPC 供方要求产品更改Supplier Request for Product Change31、SREA 供方工程批准的要求Supplier Request for Engineering Approval32、IAA 临时批准授权Interim Approval Authorization33、AAR 外观件批准报告Appearance Approval Report34、PTR 试生产(报告) Production Trial Run (Report)35、DCP尺寸控制计划(动态控制计划)Dimension Control Plan (Dynamic Control Plan)37、防错（POKA-YOKE）Mistake Proofing 加工订单Fabrication Order补足欠交Fill Backorder总装提前期Final Assembly Lead Time确认的计划订单Firm Planned Order固定订货批量F ixed Order Quantity集中预测Focus Forecasting完全跟踪Full Pegging通用生产管理原则Generally Accepted Manufacturing Practices毛需求Gross Requirements在制品库存In Process Inventory独立需求Independent Demand投入/产出控制Input/ Output Control检验标识Inspection ID厂际需求Interplant Demand库存周转率Inventory Carry Rate仓库库位类型Inventory Location Type库存周转次数Inventory Turnover发送订单Issue Order项目记录Item Record物料项目Item加工车间Job Shop准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time层Level负荷量Load Leveling负荷报告Load Report负荷Load仓位代码Location Code仓位备注Location Remarks仓位状况Location Status按需订货Lot for Lot批量标识Lot ID批量编号Lot Number批量Lot Size低位码Low Level Code机器能力Machine Capacity机器加载Machine Loading外购或自制决策Make or Buy Decision面向订单生产的产品Make-to-order Product 面向库存生产的产品Make-to-stock Product 制造周期时间Manufacturing Cycle Time制造资源计划Manufacturing Resource Planning (MRP II)主生产计划Master Production Schedule (MPS)物料成本Material Cost物料发送和接收Material Issues and Receipts 物料需求计划Material Requirements Planning (MRP)登陆标志MPS Book Flag MPS多重仓位Multiple Location净改变式MRP N et Change MRP净需求Net Requirements新仓位New Location新组件New Parent新仓库New Warehouse不活动报告No Action Report 现有库存量On-hand Balance未结订单Open Order订单输入Order Entry订货点Order Point订货方针Order Policy订货承诺Order Promising订货备注Order Remarks双亲Parent零件清单Part Bills零件批次Part Lot零件编号Part Number零件Part反查Pegging领料单Picking List领料/提货Picking计划订单Planned Order后减库存处理法Post-deduct Inventory Transaction Processing前减库存处理法Pre-deduct Inventory Transaction Processing发票价格Price Invoice采购订单价格Price Purchase Order优先计划Priority Planning产品控制Product Control产品线Production Line生产规划编制Production Planning产品率Production Rate产品结构树Production Tree预计可用库存Projected Available Balance采购订单跟踪Purchase Order Tracking已分配量Quantity Allocation仓位数量Quantity At Location欠交数量Quantity Backorder完成数量Quantity Completion需求量Quantity Demand毛需求量Quantity Gross进货数量Quantity In排队时间Queue Time队列Queue重生成式MRP Regenerated MRP重排假设Rescheduling Assumption资源需求计划Resource Requirements Planning粗能力计划Rough-cut Capacity Planning工艺路线Routing安全库存量Safety Stock保险期Safety Time预计入库量Scheduled Receipt残料率Scrap Factor发送零件Send Part维修件Service Parts发货地址Ship Address发货单联系人Ship Contact发货零件Ship Date发货单Ship Order工厂日历Shop Calendar车间作业管理Shop Floor Control损耗系数Shrinkage Factor标准产品成本Standard Product Cost标准机器设置工时Standard Set Up Hour标准单位运转工时Standard Unit Run Hour 标准工资率Standard Wage Rate状况代码Status Code库存控制Stores Control建议工作单Suggested Work Order约束理论Theory of Constraints (TOC)时间段Time Bucket时界Time Fence单位成本Unit Cost采购计划员Vendor Scheduler采购计划法Vendor Scheduling工作中心能力Work Center Capacity工作中心Work Center在制品Work in Process工作令跟踪Work Order Tracking工作令Work Order工作进度安排Work Scheduling零库存Zero Inventories经济订货批量＝Squat(2*年订货量*平均一次订货准备所发生成本/每件存货的年储存成本)美国生产和库存控制协会APICS，American Production & Inventory Control Society五、生产注塑机injection machine冲床Punch machine混料机blender mixer尼龙nylon 黄铜brass青铜bronze紫(纯)铜copper料斗hopper麻点pit配料compounding涂层coating飞边flash预热preheating再生料reworked material再生塑料reworked plastics工艺设计process design紧急停止emergency stop延时time delay六．物控保质期shelf lifeABC分类法ABC Classification反常需求Abnormal Demand措施信息Action Message活动报告标志Action-report-flag基于活动的成本核算Activity-based Costing (ABC)实际能力Actual Capacity实际成本Actual Costs调整现有库存量Adjust-on-hand已分配量Allocation替代工序Alternative Routine装配订单Assembly Order装配零件表Assembly Parts List装配Assembly计划自动重排Automatic Rescheduling可达到库存Available Inventory可用材料Available Material达到库存Available Stock可利用工时Available Work可签约量Available-to-promise平均库存Average Inventory欠交订单Back Order倒序计划Back Scheduling倒冲法Back flush未完成订单Backlog现有库存余额Balance-on-hand Inventory批号Batch Number批量生产Batch Production标杆瞄准Benchmarking工时清单Bill of Labor提货单Bill of Lading物料清单Bill of Material分库Branch Warehouse经营规划Business Plan采购员Buyer能力管理Capacity Management能力需求计划Capacity Requirements Planning (CRP)保管费率Carrying Cost Rate保管费Carrying Cost单元式制造Cellular Manufacturing修改批量日期Change Lot Date修改工序Change Route修改产品结构Change Structure检查点Check Point闭环物料需求计划Closed Loop MRP通用工序标识Common Route ID计算机集成制造Computer-integrated Manufacturing (CIM)配置代码Configuration Code约束管理/约束理论Constraints Management/Theory of Constraints (TOC)依成本的材料清单Costed Bill of Material急需零件Critical Part累计提前期Cumulative Lead Time现有运转时间Current Run Hour现有运转数量Current Run Quantity周期盘点Cycle Counting调整日期Date Adjust有效日期Date Available修改日期Date Changed结束日期Date Closed截止日期Date Due生产日期Date in Produced库存调整日期Date Inventory Adjust作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required发货日期Date to Pull空负荷Dead Load需求管理Demand Management 需求Demand实际能力Demonstrated Capacity非独立需求Dependent Demand直接增减库存处理法Direct-deduct Inventory Transaction Processing发料单Disbursement List派工单Dispatch List分销资源计划Distribution Resource Planning (DRP)鼓－缓冲－绳子Drum-buffer-rope经济订货批量Economic Order Quantity (EOQ)工程变更生效日期Engineering Change Effect Date工程变更生效单Engineering Change Effect Work Order工程停止日期Engineering Stop Date例外控制Exception Control呆滞材料分析Excess Material Analysis急送代码Expedite Code三、模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core 斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine 四、品管SPC statistic process control品管保证Quality Assurance品管控制Quality control来料检验IQC Incoming quality control巡检IPQC In-process quality control校对calibration动态试验dynamic test环境试验Environmental test非破坏性试验non-destructive test光泽gloss击穿电压(dielectric) breakdown voltage拉伸强度tensile strength冷热骤变试验thermal shock test环境试验炉Environmental chamber盐雾实验salt spray test绝缘电阻测试验仪Insulating resistance meter内应力internal stress疲劳fatigue蠕变creep试样specimen撕裂强度tear strength缩痕shrink mark, sink mark耐久性durability抽样sampling样品数量sample sizeAQL Acceptable Quality level批量lot size抽样计划sampling planOC曲线operation curve试验顺序sequence of tests环境温度ambient temperature可焊性solderability阻燃性flame resistance一、组织机构及职位XX电子有限公司XX Electronics CO., Ltd 总经理办公室General manager’s office企管部Enterprise management department (EM)行政部Administration department (AD)销售部Sales department (SD)财务部Financial department (FD)技术部Technology department (TD)物控部Production material control department (PMC)生产部Production department(PD)模具部Mold manufacturing department, Tooling manufacturing department (TM)品管部Quality Assurance department (QA) 冲压车间Stamp workshop, press workshop 注塑车间injection workshop装配车间Assembly workshop模具装配车间Mold and die Assembly workshop金属加工车间metal machine workshop电脉冲车间Electric discharge process workshop线切割车间wire cutting process workshop工磨车间Grinding workshop总经理General manager (GM)副总经理Vice-general manager经理manager董事长president副董事长Vice-presidentXX部门经理Manager of XX department主任、主管supervisor拉长Line leader组长Foreman, forelady秘书secretary文员clerk操作员operator助理assistant二、产品连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压rated voltage额定电流rated current接触电阻contact resistance绝缘电阻insulation resistance超声波焊接ultrasonic welding耐压withstand voltage针pin物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity接触长度contact length接触件电镀层contact plating接触压力contact pressure接触件中心距contact space接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring多层印制电路Multilayer printed circuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board 表面安装surface Mounting翘曲warp，bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance。
塑料加工英文词汇表
baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave 凹convex凸short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill钻boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边。
塑料方面英语词汇表
第一部份：单词及词组特性Property标准Standard测试方法Test Method测试条件 Test condition单位 Unit物理性能Physical密度Density密度分布Density Distribution相对湿度RH（Relative Humidity）熔体流动指数Melt Flow Index熔体流动速率Melt Flow Rate吸水性（23℃下在水中浸泡24小时） Water absorption, 24h in water at 23℃纵向收缩率Moulding shrinkage longitudinal横向收缩率Moulding shrinkage transverse洛氏硬度Rockwell Hardness肖氏硬度Shore Hardness机械性能Mechanical拉伸强度Tensile Strength拉伸屈服强度Tensile Strength at Yield屈服强度Yield Stress断裂伸长率Strain at Break/Elongation at Break拉伸模量Tensile Modulus弯曲强度Flexural Strength弯曲模量Flexural Modulus剪切模量Shear Modulus最大负载拉伸强度Tensile Strength at Max Load简支梁缺口冲击强度Notched Charpy Impact Strength简支梁无缺口冲击强度Unnotched Charpy Impact StrengthIZOD缺口冲击强度IZOD Notched Impact Strength 热性能Thermal热变形温度Heat Deflection Temperature燃烧性Flammability维卡软化温度 Vicat Softening Temperature维卡软化点 Vicat Softening Point热分析Thermal Analysis差热分析DTA（Differential Thermal Analysis）焓变Enthalpy Change熔点Melt Point差式扫描量热法测试DSC TEST（DIFFERENTIAL SCANNING CALORIMETRY）红外光谱测量 INFRARED SPECTROPHOTOMETRY 电性能Electrical介电常数Dielectric Constant相对介电常数Relative Permittivity体积电阻率 Electrical Volume Resistivity表面电阻率 Electrical Surface Resistivity电介质强度, 绝缘强度 Dielectric Strength耗散因数(介质损耗角) Dissipation Factor其它 Other融体温度Melting Temperature融体温度范围Melt Temperature Range最合适融体温度Melt Temperature Optimum模温Mold Temperature模温范围Mold Temperature Range最合适模温Mold Temperature Optimum干燥Dry干燥时间Drying Time干燥温度Drying Temperature料桶（射台）温度 Barrel Temperature下料段 Feed Zone压缩（塑化）段 Compression Zone前（射嘴）段 Front Zone直接纺丝拉伸法DSD（DIRECT SPINNING DRAW）高耐热、高耐冲击级聚合物HIGH HEAT RESISTANT, HIGH IMPACT MOLDING COMPOUND内饰INTERIOR外饰EXTERIOR增强热塑性塑料RTP（REINFORCED THERMOPLASTICS）增强热固性树脂管材RTRP（REINFORCED THEROSETTING RESIN PIPE）室温硫化RTV（ROOM TEMPERATURE VULCANIZATION）纤维增强不饱和树脂FRP（FIBER REINFORCED PLASTICS）塑料、塑胶 PLASTIC模具 MOULDING 、TOOLING温度 TEMPERATURE压力PRESSURE速度SPEED、VELOCITY时间TIME循环CYCLE填充PACK保压HOLD冷却COOLING冷却液COOLING FLUID延迟、保压DWELL保压压力DWELL PRESSURE产品部PRODUCT DEPARTMENT研发中心RESEARCH AND EXPLOITATION CENTER质量部QUALITY DEPARTMENT采购部STOCK DEPARTMENT营销部SELL DEPARTMENT设备部EQUIPMENT DEPARTMENT制造部MANUFACTURE DEPARTMENT财务部FINANCE DEPARTMENT总经办GENERAL MANAGER OFFICE塑胶车间PLASTIC WORKSHOP模具车间MOULDING WORKSHOP模具库：MOULD STOREROOM注塑A区：INJECTION SECTION：A注塑B区：INJECTION SECTION：B注塑C区：INJECTION SECTION：C喷漆区：PAINT SECTION搪塑区：SLUSH MOULDING SECTION发泡区：FOAM SECTION成品库区：FINISHED PRODUCT SOREROOM SECTION原材料区：RAW MATERIAL SECTION物质存放区：MATTER STORE SECTION数控加工区：NUMERICAL CONTROL MACHINING SECTION合金钢ALLOY STEEL温控TEMPERATURE CONTROL机头温控DIE HEAD TEMPERATURE CONTROL运行指令RUN INDICATION实际PRACTICAL设定SETTING实际显示PV设定显示SV螺杆转速SCREW SPEED加料转速CHARGING SPEED油泵启停OIL PUMP START-STOP 水泵启停W ATER PUMP START-STOP真空启停V ACUUM START-STOP不定式INFINITIVE过去式PAST TENSE过去分词PAST PARTICIPLE现在时PRESENT TENSE原理原则PRINCIPLE控制计划Control Plan反应注塑RIM（REACTION MOULDING）每分钟转数rpm（ROUNDS PER MINUTE）每秒钟转数rps（ROUNDS PER SECOND）增强塑料RP（REINFORCED PLASTICS）减速比、压缩比REDUCTION RATIO比浓黏度RSV（REDUCED SPECIFIC VISCOSITY）室温RT（ROOM TEMPERATURE）树脂压铸RTM（RESIN TRANSFER MOULDING）综合INTEGRATION机智的、聪明INTELLIGENT饮料BEVERAGE检查INSPECTION与众不同，独具特色DISTINCTIVE行为、业绩PERFORMANCE被覆、衣料COATING裁缝、缝纫SEWING裁缝师SEWER TAILOR精心策划：ABORATIVE PLAN严格控制：STRICT CONTROL持续改进：PERSISTENT IMPROVING顾客满意：USER SATISFACTIONPA 聚酰胺(尼龙)PA-1010 聚癸二酸癸二胺(尼龙1010)PA-11 聚十一酰胺(尼龙11)PA-12 聚十二酰胺(尼龙12)PA-6 聚己内酰胺(尼龙6)PA-610 聚癸二酰己二胺(尼龙610)PA-612 聚十二烷二酰己二胺(尼龙612)PA-66 聚己二酸己二胺(尼龙66)PA-8 聚辛酰胺(尼龙8)PA-9 聚9-氨基壬酸(尼龙9)PAA 聚丙烯酸PAAS 水质稳定剂PABM 聚氨基双马来酰亚胺PAC 聚氯化铝PAEK 聚芳基醚酮PAI 聚酰胺-酰亚胺PAM 聚丙烯酰胺PAMBA 抗血纤溶芳酸PAMS 聚α－甲基苯乙烯PAN 聚丙烯腈PAP 对氨基苯酚PAPA 聚壬二酐PAPI 多亚甲基多苯基异氰酸酯PAR 聚芳酰胺PAR 聚芳酯(双酚A型)PAS 聚芳砜(聚芳基硫醚)PB 聚丁二烯-［1，3］PBAN 聚(丁二烯-丙烯腈)PBI 聚苯并咪唑PBMA 聚甲基丙烯酸正丁酯PBN 聚萘二酸丁醇酯PBR 丙烯-丁二烯橡胶PBS 聚(丁二烯-苯乙烯)PBT 聚对苯二甲酸丁二酯PC 聚碳酸酯PC/ABS 聚碳酸酯/ABS树脂共混合金PC/PBT 聚碳酸酯/聚对苯二甲酸丁二醇酯弹性体共混合金PCD 聚羰二酰亚胺PCDT 聚(1，4-环己烯二亚甲基对苯二甲酸酯) PCE 四氯乙烯PCMX 对氯间二甲酚PCT 聚对苯二甲酸环己烷对二甲醇酯PCT 聚己内酰胺PCTEE 聚三氟氯乙烯PD 二羟基聚醚PDAIP 聚间苯二甲酸二烯丙酯PDAP 聚对苯二甲酸二烯丙酯PDMS 聚二甲基硅氧烷PE 聚乙烯PEA 聚丙烯酸酯PEAM 苯乙烯型聚乙烯均相离子交换膜PEC 氯化聚乙烯PECM 苯乙烯型聚乙烯均相阳离子交换膜PEE 聚醚酯纤维PEEK 聚醚醚酮PEG 聚乙二醇PEHA 五乙撑六胺PEN 聚萘二酸乙二醇酯PEO 聚环氧乙烷PEOK 聚氧化乙烯PEP 对-乙基苯酚聚全氟乙丙烯薄膜PES 聚苯醚砜PET 聚对苯二甲酸乙二酯PETE 涤纶长丝PETP 聚对苯二甲酸乙二醇酯PF 酚醛树脂PF/PA 尼龙改性酚醛压塑粉PF/PVC 聚氯乙烯改性酚醛压塑粉PFA 全氟烷氧基树脂PFG 聚乙二醇PFS 聚合硫酸铁PG 丙二醇PGEEA 乙二醇(甲)乙醚醋酸酯PGL 环氧灌封料PH 六羟基聚醚PHEMA 聚(甲基丙烯酸-2-羟乙酯) PHP 水解聚丙烯酸胺PI 聚异戊二稀PIB 聚异丁烯PIBO 聚氧化异丁烯PIC 聚异三聚氰酸酯PIEE 聚四氟乙烯PIR 聚三聚氰酸酯PL 丙烯PLD 防老剂4030PLME 1：1型十二(烷)酸单异丙醇酰胺PMA 聚丙烯酸甲酯PMAC 聚甲氧基缩醛PMAN 聚甲基丙烯腈PMCA 聚α-氧化丙烯酸甲酯PMDETA 五甲基二乙烯基三胺PMI 聚甲基丙烯酰亚胺PMMA 聚甲基丙烯酸甲酯(有机玻璃) PMMI 聚均苯四甲酰亚胺PMP 聚4-甲基戊烯-1PNT 对硝基甲苯PO 环氧乙烷POA 聚己内酰胺纤维POF 有机光纤POM 聚甲醛POP 对辛基苯酚POR 环氧丙烷橡胶PP 聚丙烯PPA 聚己二酸丙二醇酯PPB 溴代十五烷基吡啶PPC 氯化聚丙烯PPD 防老剂4020PPG 聚醚PPO 聚苯醚(聚2，6-二甲基苯醚) PPOX 聚环氧丙烷PPS 聚苯硫醚PPSU 聚苯砜(聚芳碱)PR 聚酯PROT 蛋白质纤维PS 聚苯乙烯PSAN 聚苯乙烯-丙烯腈共聚物PSB 聚苯乙烯-丁二烯共聚物PSF(PSU) 聚砜PSI 聚甲基苯基硅氧烷PST 聚苯乙烯纤维PT 甲苯PTA 精对苯二甲酸PTBP 对特丁基苯酚PTFE 聚四氟乙烯PTMEG 聚醚二醇PTMG 聚四氢呋喃醚二醇PTP 聚对苯二甲酸酯PTX 苯(甲苯、二甲苯)PTX 苯(甲苯、二甲苯)PU 聚氨酯(聚氨基甲酸酯)PV A 聚乙烯醇PV AC 聚醋酸乙烯乳液PV AL 乙烯醇系纤维PVB 聚乙烯醇缩丁醛PVC 聚氯乙烯PVCA 聚氯乙烯醋酸酯PVCC 氯化聚氯乙烯PVDC 聚偏二氯乙烯PVDF 聚偏二氟乙烯PVE 聚乙烯基乙醚PVF 聚氟乙烯PVFM 聚乙烯醇缩甲醛PVI 聚乙烯异丁醚PVK 聚乙烯基咔唑PVM 聚烯基甲醚PVP 聚乙烯基吡咯烷酮色差Aberration雾化Atomization 滞料纹Bank Mark咬入 Bite涂料孔(铸疵) Blacking Hole 涂料疤Blacking Scab起泡Blister起霜 Blooming破孔 Blow Hole泛白 Blushing侧壁皱纹 Body Wrinkle冒口带肉 Breaking-in膜泡 bubble糊斑 burn mark毛边 burr翘曲 camber气泡cell表面中部波皱 center buckle 细裂痕check龟裂 checking修整表面缺陷 chipping铸件凹痕 clamp-off塌陷 collapse色斑 color mottle腐蚀 corrosion裂痕 crack碎裂 crazing龟裂 crazing变形 deformation切边碎片 edge裂边 edge crack退色 fading填充料斑 filler speak裂纹 fissure凸缘起皱 flange wrinkle刮伤 flaw流痕 flow mark毛边 galling光滑 glazing光泽 gloss污斑 grease pits磨痕 grinding defect雾度haze水锈 incrustation压痕 indentation内部气孔 internal porosity 偏模 mismatch斑点 mottle缩颈 necking割痕 nick橘皮状表面缺陷 orange peel溢流 overflow剥离 peeling点状腐蚀 corrosion模板印痕plate mark麻点 pock痘斑pock mark树脂流纹 resin streak树脂脱落 resin wear凹陷riding松垂 sagging皂化 saponification疤痕scar废料 scrap废料阻塞scrap jam刮伤/划痕 scratch深冲表面划伤 scuffing裂痕 seam模口挤痕 shock line充填不足 short shot凹孔shrinkage pool凹痕 sink mark表皮折迭 skin inclusion矫直 straightening条状痕streak表面裂痕 surface check橘皮状表皮皱折surface roughening波动 surging冒汗sweat out扭曲 torsion翘曲 warpage波痕 waviness熔塌webbing焊痕 weld mark白化 whitening皱纹wrinkle品质管理人员 QC quality control终点质量管理人员 FQC final quality control制程中的质量管理人员 IPQC in process quality control最终出货质量管理人员 OQC output quality control 进料质量管理人员 IQC incoming quality control 全面质量管理 TQC total quality control段检人员 POC passage quality control质量保证人员 QA quality assurance出货质量保证人员 OQA output quality assurance 质量工程人员 QE quality engineering新品首件检查 FAI first article inspection首件确认 FAA first article assurance模具确认报告 TVR tool verification report能力指数 CP capability index过程能力参数 CPK capability index of process合格供货商质量评估 SSQA standardized supplier quality开箱检查 OOBA out of box audit质量机能展开 QFD quality function deployment失效模式分析FMEA failure model effectiveness analysis最后一次稽核 FA final audit改正行动要求 CAR corrective action request改正行动报告 corrective action report运作类允收质量水平 AQL Acceptable Quality Level抽样检验样本大小 S/S Sample size允收 ACC Accept拒收 REE Reject极严重的 CR Critical主要的 MAJ Major轻微的 MIN Minor平均出厂质量 AOQ Average Output Quality平均出厂质量 AOQL Average Output Quality Level 质量/可靠度服务 Q/R/S Quality/Reliability/Service 首件检查报告 FPIR First Piece Inspection Report 百万分之… PPM Percent Per Million第二部分：短文ISO 868Plastics and ebonite –Determination of indentation hardness by means of a durometer (Shore hardness)8 Procedure8.1 Place the test specimen on a hard, horizontal, plane surface. Hold the durometer in a vertical position with the point of the indenter (4.2) at least 9 mm form any edge of the foot parallel to the surface of the test specimen. Apply just sufficient pressure to obtain firm contact between presser foot and test specimen.NOTE Better reproducibility may be obtained by using either a durometer stand or a weight centred on the axis of the indenter, or both, to apply the presser foot to the test specimen. Recommended masses are 1kg for the type A durometer and 5kg for the type D durometer.Read the scale of the indicating device (4.3) after 15s±1s. If an instantaneous reading is specified, read the scale within 1 s after the presser foot is in firm contact with the test specimen, unless the durometer has a maximum indicator, in which case the maximum reading shall be taken.8.2 Make five measurements of hardness at different positions on the test specimen at least 6 mm apart and determine the ISO 868塑料、硬橡胶硬度计压入硬度试验方法（邵氏硬度）8 步骤8.1 把试样放置在坚固的水平面上，垂直拿住硬度计并使硬度计压针距离试样品边缘至少9mm。
常见包装英语大全
常见包装英语大全在全球化的今天，包装已经成为商品销售的重要环节之一。
而包装英语作为一种专业语言，也逐渐被人们所关注和应用。
本文将为大家介绍一些常见包装英语词汇和短语，以便读者能更好地了解和运用这一领域的专业术语。
一、包装材料1. 纸盒（Carton）- 一种常见的包装容器，由纸和纸板制成。
2. 塑料袋（Plastic bag）- 以塑料为材料制成的容器，常用于储存和运输商品。
3. 瓶子（Bottle）- 通常用于贮存和销售液体或粉状商品的容器。
4. 罐头（Can）- 金属容器，用于装载食品或饮料等商品。
5. 泡沫（Foam）- 一种轻质的材料，常用于保护易碎物品，如电子产品等。
二、包装过程1. 包装设计（Packaging design）- 设计包装外观和结构，以满足商品的营销需求和保护需求。
2. 印刷（Printing）- 在包装上印刷图案、文字等内容。
3. 原材料采购（Raw material procurement）- 采购包装所需的材料，如纸张、胶水等。
4. 包装生产线（Packaging production line）- 用于完成包装过程中的各项任务的生产设备。
5. 封箱（Sealing）- 封闭包装容器的过程，以确保商品的安全。
三、包装标识1. 商标（Trademark）- 表示商品来源和品牌的标记。
2. 标签（Label）- 附着在包装上的信息标识，包含商品的名称、规格、成分等信息。
3. 条形码（Barcode）- 用于商品识别和跟踪的图形标记。
4. 防伪标识（Anti-counterfeiting label）- 用于判断商品真伪的标志，以保障消费者的权益。
四、包装环保1. 绿色包装（Green packaging）- 以环保材料和技术制作的包装。
2. 循环利用（Recycling）- 对废弃包装材料的再次利用。
3. 环保认证（Environmental certification）- 对符合环保标准的包装进行认证，如FSC（森林管理委员会）认证等。
塑料原料、助剂词汇大全
赋予表面层弹性和稳定性，能显著降低表面张力的化合物。在表面或界面上分子趋向于收缩，通常两性表面活性剂有亲水基团和憎水基团，亲水基团可以是离子的或非离子的。
同义词：溶胶稳定剂，乳化剂。
不饱和聚酯(Unsaturated Polyester)（UP） (引申定义)
A
A-阶段(A-stage)
热固性树脂聚合的初阶阶段，在这一阶段材料仍溶解在某种溶剂中或处于熔融状态。
参看B-阶段, C-阶段
ABS树脂――丙烯腈、丁二烯和苯乙烯聚合而成(Acrylonitrile Butadiene Styrene resin, ABS)
ABS树脂是一种多相的材料。它有很好的抗冲击性能，很好的结构强度，并且有光泽而致密的表面,同时它也具有很高的刚性和冲击强度，很好的耐磨损性能，极好的电性能，抗潮湿性能和延展性能。ABS树脂能耐无机盐和酸碱，它通常在真空条件下加工、成形和挤出。（工作温度范围：-25℃到+60℃）。
吹塑成膜(Film Blowing)
熔体通过一个环形模腔挤出，然后膨胀，再冷却成型为一个薄膜。吹膜被用来生产有高的机械力学性能的超薄膜，主要是用于聚乙烯加工。
冲击性能改性剂(Impact modifier)
添加在一些材料中，特别是是不同种类的橡胶和塑料，能和基体成为一体并提高所得材料的耐冲击性能（能够抵抗突然施加的拉力和振动）。
吹塑(Blowing/Foaming agent)(引申定义)
通过靠着一个模具的内表面膨胀一个热塑性塑料制造所谓的料坯的加工过程。这是制造塑料瓶子、广口容器、油桶等工具的一种常用方法。
吹塑薄膜(Blown film)(引申定义)
常用塑胶英文单词
常用塑胶英文单词(2009/11/07 09:14)目录：常用塑胶英文单词做塑胶，分享些与之有关的词汇。
嵌件---insert嵌件销---insert pin气胀真空成形---air assist forming空气隙---air gap空气顶出---air ejection永久伸长---permanent elongation,tension set永久变形---permanent set,permanent deformation蚀刻,侵蚀---etching应力---stress应力鬆弛---stress relaxation应力龟裂---stress cracking应力集中---stress concentration应力断裂,应力破坏---stress rupture应力.应变曲线---stress-strain curve应力.应变图---stress-strain diagram托板,模板---retainer plate硬度---hardness合模机构---mold clamping mechanism合模力,闭模力---locking force,clamping force开模力---mold opening force悬臂梁---cantilever beam润滑剂---lubricant模具---mold,Tools,Tooling模温度控制器---mold temperature controller模具尺寸---mold size加热管套(料筒)---heating cylinder加热板---heating plate凸轮---cam玻璃纤维---glass fiber,fibrous glass玻璃纤维强化热塑塑胶---fiber glass reinforced thermoplastics,FRTP,glass fiber reinforced thermoplasitcs,GRTP玻璃纤维强化塑胶---glass fiber reinforced plastics,GRP,fiber galss reinforced plastics,FRP.感光聚合物---photopolymer,photo-sensitive polymer镜面抛光---mirror polishing龟裂---cracking龟裂---crack颗粒料---granule石墨---graphite石墨纤维---graphite fiber间隙, 隙距---clearance模蕊,蕊片,蕊线,蕊孔---core成孔销,模蕊销---core pin成孔销托板---core pin plate公差,容差---tolerance冷料---cold slug冷料井,冷料窝---cold slug well回程销,覆归销---surface pin冷热骤变试验---thermal shock test热应力龟裂---thermal stress cracking,TSC 侧向浇口---side gate侧向模蕊(心型)销---side draw pin砂磨---sanding喷砂,打砂---sand blast修饰,涂饰,打光---finishing自断浇口,剪切浇口---shear gate紫外线---ultraviolet, UV紫外线稳定剂---UV stabilizer紫外线吸收剂---UV absorber压花---embossing压花机---embossing machine喷霜,起霜---blooming exudation鯊皮斑---shark skin射出压力---injection pressure射出成形---injection molding射出成形机---injection molding machine 射出成形模具---injection mold射出装置---injection unit射出速度---injection speed射出喷嘴,注料嘴---injection nozzle射出容量---machine shot capacity射出率(量)---injection rate煮沸试验---boiling test充填不足,缺料---short shot手动模具---hand mold,loose mold手动油压机---hand press缩窝,凹孔---shrinkage pool衝击试验---inpact test衝击强度---impact strength烧结法,粉铸法---sintering烧结成形法---sinter molding模板---mold plate注射,射料---shot硅橡胶---silicone rubber真空成形---vacuum forming珠光顏料---pearlescent pigment浸渍涂装---dip coating人造皮革---artificial leather废料粉碎机---scrap grinder顶出板,脱模板---stripper plate应力龟裂---stress cracking环境应力龟裂试验---environmental stress cracking test行程,衝程---stroke注道,注道料---sprue注道衬套,浇口衬套---sprue bush成形压力,模製压力---molding pressure成形温度,模製温度---molding temperature成形循环,成形週期---molding cycle成形时间,模製时间---molding time成形收缩,模压收缩---mold shrinkage, molding shrinkage窄浇口,限制形浇口---restricted gate剪切强度,抗剪强度---shear strength增亮剂---brightening agent,optical brightener,optical whitening agent 加速试验---accelerated test加速老化---accelerated ageing塑性变形---plastic deformation塑性流动---plastic fiow翘曲---warp(ing),warpage抗臭氧性---ozone resistance抗臭氧试验---ozone resistance test耐天侯性---weatherability,weather resistance耐光性---light resistance,light fastness天侯老化试验---weathering test耐酸性---acid resistance耐衝击性---impact resistance褪色---fading,discoloration耐蚀性---corrosion resistance拉桿,导柱---tie-bar拉桿间距---tie-bar distance多模穴模具---multi-cavity mold双色射出成形---double-shot molding超音(声)波镶嵌---ultrasonic inserting超音(声)波焊接---ultrasonic welding顶出,脱模---ejection顶出组合---ejector顶出板---ejector plate,knock-out plate顶出桿,脱模桿---knock-out bar,ejector rod无光面---dull surface低压射出成形法---low pressure injection molding硬度计---durometer电镀---electroplating,electrodeposition电铸模具---electroformed mold尼龙,(聚醯胺树脂之俗称)---nylon尼龙纤维---nylon fiber扭曲试验---torsion test扭力矩---torsion moment喷嘴,注嘴---nozzle喷嘴接触---nozzle touching喷嘴止流---nozzle shut-off支管形喷嘴---nozzle manifold脱模销,顶出销---knock-out pin脱模销托板,顶出销托板---knock-out pin plate背压---back pressure止回阀,止逆阀---back pressure valve发泡剂---blowing agent,expanding agent发泡塑胶,泡沫塑料---plastics foam,expanded plastics, foamed plastics,cellular plastics,plastics sponge抛光布轮---buff,buffing wheel布轮抛光---buffing毛边,整纹,溢料---flash,fin修边,除边---deflashing,definning修边机,修毛边机---deflasher手工脱模,手工顶出---hand ejection剥离,剥皮加工---peeling剥离试验---peeling test拉出成形---pultrusion凹痕,缩痕---sink mark,shrink mark抗刮硬度,刮痕硬度---scratch hardness非破坏性试验---non-destructive testing起泡,气泡---blister疲劳试验---fatigue test疲劳寿命---fatigue life疲劳强度---fatigue strength针眼,针孔---pinhole玻璃纤维强化,热塑塑胶射出成形---fiberfil molding起泡,气泡---blister底漆,底胶,引发剂---primer溢料---flash溢料缝,毛边槽---flash groove流痕---flow mark冷却线---frost line原型模,试验模---prototype mold环境温度---ambient temperature止流阀---shut-off valve孔隙,空洞,气泡---void放电---discharge全压式模具---positive mold辅助压缸---auxiliary cylinder烫印---hot stamping,roll leaf stamping弯曲龟裂---flex cracking磨损---abrasion,wear磨耗---abrasion loss莫斯硬度---Mohs’hardness退火---annealing回火---tempering杨氏弹性系数---Young’s modulus of elasticity 油压增压器---hydraulic intensifier油压机---hydraulic press油压马达---hydraulic motor焊接---welding内衬,衬套,衬垫---liner流道,流道料---runner合模销,导销---leader pin合模销套,导销衬套---leader pin bushing回程销, 覆归销---return pin冷却水通路---cooling channel常温成形,冷模压---cold molding老化试验---ageing test对位圈,定位环---locating ring熔合线,结合线---weld line肉厚---wall thickness脱模斜度---draft angle母模---cavity side顶出销,顶针---ejector pin分模线---parting line浇口,灌点---gate竖浇道---sprue浇道,流道---runner模仁,雄模,模心---core side浇口白晕---gate bush凹痕,缩痕,缩水---sink mark银线---silver line隧道形浇口---tunnel gate沉陷式浇口,潜入式浇口---submarine gate针孔形浇口---pin point gate注道形浇口,直接浇口---sprue gate毛边形浇口,薄膜形浇口---flash gate,external ring gate,internal ring gate喷流,喷射现象---jetting剥料板---stripper plateMould components & AccessoriesMould base 模胚Bolts 螺栓Mould frame 模架screw 螺丝Top clamp plate 面板Stripper screw 脱料螺丝Bottom clamp plate 底板 F.H.C. screw（flat head cap screw）平头螺丝Socket head sountersunk screws 平头螺丝Hot runner plate 热流道板S.H.C. screw( socket head cap screw) 杯头螺丝Runner plate 水口板hexagonal socket head cap screw 杯头螺丝A plate A板Hexagonal head screw 六角头螺丝B plate B板Grub screw 无头螺丝（等高螺丝，基米螺丝）Stripper plate 推板Ball screw 波仔螺丝Support plate 支撑板Shoulder screw 限位螺丝（带肩螺丝，塞打螺丝）Spacer plate 方铁latch 插销Ejector retainer plate 顶针面板baffle 隔水片Ejector plate 顶针板plugs 喉塞Insulating plate 隔热板Jiffy plugs 喉咀Cavity 前模o-ring 密封圈Cavity insert 前模镶件Cooling tube 散热管Core 后模spring 弹簧Core insert 后模Support pillar 撑头Slide 行位Stop pin 垃圾钉Slide insert 行位镶件Dowel pin 管钉jaw 行位压块Spacer ring/washer 间隙圈Slide wear plate 行位耐磨块Venting slots 排气槽Slide guide block 行位导向块thermocouple 电热偶Slide lock 行位锁/行位扣Thermocouple connector 接线盒Wedge block 铲机Limit switch 限位开关W.B. wear plate 铲机耐磨块probe 探针Core pin 镶针Pry bar slots 开模槽Angle pin 斜导柱Safety strap 模锁Angle lifter 斜顶Lifting eye bolt 吊环（方向已固定）Lifter guide block 斜顶导向块Hydraulic cylinder 油缸Lifter base 斜顶座Air cylinder 气缸Press block 模料挤紧块Hydraulic motor 马达hoist ring 吊环（可转动方向）Knock out hole 顶棍孔Parting lock 树脂开闭器（尼龙扣）Name plate 铭牌Straight side interlocks T型锁（直身锁）Date code 日期印Tapered interlocks 斜度锁Cavity number 模穴号sensor 感应器engrave 刻字/凹入heater 加热器Raised out 凸出K.O. insert 顶棍孔镶件Gate type & runnerDrop gate 点水口Sprue bushing 唧嘴Pin point gate 细水口Sprue/gate 浇口Edge/side gate 边水口Center sprue/sprue gate 中心进胶/直浇口runner shut off 流道开关/转水口Sub gate 潜水口Runner lock pin 水口扣针Tunnel gate 隧道浇口Puller 拉钩Ring gate 环形浇口Sprue lock pin 拉料杆Fan gate 扇形浇口Slag well 冷料井Valve gate 针阀式水口Banana gate 香蕉水口Guide＆Locating systemGuide pin/leader pin 导柱Grinder研磨机Crane 天车（吊车）Guide bushes 导套Grinding machine 磨床Groover machine 开槽机locating ring 法兰Lathe machine 车床Radial drill摇臂钻床EGB( ejector guide bush) 中托司Milling machine 铣床Wire cut machine 线割机Ejecting systemEjector pin 顶针Gear 齿轮Stepped ejector pin 有托顶针Rack 齿条Blade ejector 扁顶针Bearing 轴承Ejector bar 顶块Roller bearings 滚珠轴承Sleeve 司筒Retraction spring 复位弹簧Stripper plate 推板Return pin 回针Unscrewing 脱螺纹Two-stage ejector 二次顶出Ejector retainer plate 顶针面板chain 链条Ejector plate 顶针板Chain wheel 链轮Stop block 限位块key 键Ejector bushes 顶针套Specification of Injection Moulding MachineDiameter of the location ring 法兰直径Nozzle radius 机嘴半径Nozzle injection hole diameter 机嘴注射孔直径Depth for the nozzle into the mould 机嘴进入模具的深度KO hole distance KO孔间距fine thread 细螺纹Rough thread 粗螺纹mould opening distance 开模距离mould thickness 模具厚度tie bar distance Tie Bar 距离Injection defectsflash 披锋Warpage/deformation 变形Ejected mark 顶白Step 断差/台阶Weld line 熔接线Short shots 短胶Sink mark 缩水Sharp corner 尖角Gas trapped 困气Sharp edge 尖边Scratch marks 拖花Air bubble 气泡Kiss off 碰穿Short shot 短射(欠充填)Shut off 擦穿位Flow mark 流纹Sticking cavity 粘前模Sticking core 粘后模Mould designplastic 胶位radius 半径Draft angle 拔模角Diameter 直径Fillet/ inside radius 圆角Inner diameter/I.D. 内径Outside radius 外转角Outer diameter/O.D. 外径Sprue bush radius 机嘴球半径boss 柱位Corner radius 转角半径Rib 骨位Part drawing 产品图hole 孔Mould drawing 模图Pre-hardened steel 预硬钢Plastic material 胶料Through hardened steel 全硬钢Parting line 分型面Filling uneven 走胶不平衡Plastic thickness 胶厚Balanced runner 平衡水口系统Shrinkage rate 缩水率Cycle time 循环周期Surface treatmentEDM 火花纹Demoulding polish 脱模抛光High polish 高抛光Medium polish 中抛光Optical/mirror polish 镜面抛光chrome 镀铬Texture 蚀纹。
常用塑胶英文单词
常⽤塑胶英⽂单词常⽤塑胶英⽂单词(2009/11/07 09:14)⽬录：常⽤塑胶英⽂单词做塑胶，分享些与之有关的词汇。
嵌件---insert嵌件销---insert pin⽓胀真空成形---air assist forming空⽓隙---air gap空⽓顶出---air ejection永久伸长---permanent elongation,tension set永久变形---permanent set,permanent deformation蚀刻,侵蚀---etching应⼒---stress应⼒鬆弛---stress relaxation应⼒龟裂---stress cracking应⼒集中---stress concentration应⼒断裂,应⼒破坏---stress rupture应⼒.应变曲线---stress-strain curve应⼒.应变图---stress-strain diagram托板,模板---retainer plate硬度---hardness合模机构---mold clamping mechanism合模⼒,闭模⼒---locking force,clamping force开模⼒---mold opening force悬臂梁---cantilever beam润滑剂---lubricant模具---mold,Tools,Tooling模温度控制器---mold temperature controller模具尺⼨---mold size加热管套(料筒)---heating cylinder加热板---heating plate凸轮---cam玻璃纤维---glass fiber,fibrous glass玻璃纤维强化热塑塑胶---fiber glass reinforced thermoplastics,FRTP,glass fiber reinforced thermoplasitcs,GRTP 玻璃纤维强化塑胶---glass fiber reinforced plastics,GRP,fiber galss reinforced plastics,FRP.感光聚合物---photopolymer,photo-sensitive polymer镜⾯抛光---mirror polishing龟裂---cracking龟裂---crack颗粒料---granule⽯墨---graphite⽯墨纤维---graphite fiber间隙, 隙距---clearance模蕊,蕊⽚,蕊线,蕊孔---core成孔销,模蕊销---core pin成孔销托板---core pin plate公差,容差---tolerance冷料---cold slug冷料井,冷料窝---cold slug well回程销,覆归销---surface pin冷热骤变试验---thermal shock test热应⼒龟裂---thermal stress cracking,TSC 侧向浇⼝---side gate侧向模蕊(⼼型)销---side draw pin砂磨---sanding喷砂,打砂---sand blast修饰,涂饰,打光---finishing⾃断浇⼝,剪切浇⼝---shear gate紫外线---ultraviolet, UV紫外线稳定剂---UV stabilizer紫外线吸收剂---UV absorber压花---embossing压花机---embossing machine喷霜,起霜---blooming exudation鯊⽪斑---shark skin射出压⼒---injection pressure射出成形---injection molding射出成形机---injection molding machine 射出成形模具---injection mold 射出装置---injection unit射出速度---injection speed射出喷嘴,注料嘴---injection nozzle射出容量---machine shot capacity射出率(量)---injection rate煮沸试验---boiling test充填不⾜,缺料---short shot⼿动模具---hand mold,loose mold⼿动油压机---hand press缩窝,凹孔---shrinkage pool衝击试验---inpact test衝击强度---impact strength烧结法,粉铸法---sintering烧结成形法---sinter molding模板---mold plate注射,射料---shot硅橡胶---silicone rubber真空成形---vacuum forming珠光顏料---pearlescent pigment浸渍涂装---dip coating⼈造⽪⾰---artificial leather废料粉碎机---scrap grinder顶出板,脱模板---stripper plate应⼒龟裂---stress cracking环境应⼒龟裂试验---environmental stress cracking test⾏程,衝程---stroke注道,注道料---sprue注道衬套,浇⼝衬套---sprue bush成形压⼒,模製压⼒---molding pressure成形温度,模製温度---molding temperature成形循环,成形週期---molding cycle成形时间,模製时间---molding time成形收缩,模压收缩---mold shrinkage, molding shrinkage窄浇⼝,限制形浇⼝---restricted gate剪切强度,抗剪强度---shear strength增亮剂---brightening agent,optical brightener,optical whitening agent 加速试验---accelerated test 加速⽼化---accelerated ageing塑性变形---plastic deformation塑性流动---plastic fiow翘曲---warp(ing),warpage抗臭氧性---ozone resistance抗臭氧试验---ozone resistance test耐天侯性---weatherability,weather resistance耐光性---light resistance,light fastness天侯⽼化试验---weathering test耐酸性---acid resistance耐衝击性---impact resistance褪⾊---fading,discoloration耐蚀性---corrosion resistance拉桿,导柱---tie-bar拉桿间距---tie-bar distance多模⽳模具---multi-cavity mold双⾊射出成形---double-shot molding超⾳(声)波镶嵌---ultrasonic inserting超⾳(声)波焊接---ultrasonic welding顶出,脱模---ejection顶出组合---ejector顶出板---ejector plate,knock-out plate顶出桿,脱模桿---knock-out bar,ejector rod⽆光⾯---dull surface低压射出成形法---low pressure injection molding 硬度计---durometer电镀---electroplating,electrodeposition电铸模具---electroformed mold尼龙,(聚醯胺树脂之俗称)---nylon尼龙纤维---nylon fiber扭曲试验---torsion test扭⼒矩---torsion moment喷嘴,注嘴---nozzle喷嘴接触---nozzle touching喷嘴⽌流---nozzle shut-off⽀管形喷嘴---nozzle manifold脱模销,顶出销---knock-out pin脱模销托板,顶出销托板---knock-out pin plate背压---back pressure⽌回阀,⽌逆阀---back pressure valve发泡剂---blowing agent,expanding agent发泡塑胶,泡沫塑料---plastics foam,expanded plastics, foamed plastics,cellular plastics,plastics sponge 抛光布轮---buff,buffing wheel布轮抛光---buffing⽑边,整纹,溢料---flash,fin修边,除边---deflashing,definning修边机,修⽑边机---deflasher⼿⼯脱模,⼿⼯顶出---hand ejection剥离,剥⽪加⼯---peeling剥离试验---peeling test拉出成形---pultrusion凹痕,缩痕---sink mark,shrink mark抗刮硬度,刮痕硬度---scratch hardness⾮破坏性试验---non-destructive testing起泡,⽓泡---blister疲劳试验---fatigue test疲劳寿命---fatigue life疲劳强度---fatigue strength针眼,针孔---pinhole玻璃纤维强化,热塑塑胶射出成形---fiberfil molding起泡,⽓泡---blister底漆,底胶,引发剂---primer溢料---flash溢料缝,⽑边槽---flash groove流痕---flow mark冷却线---frost line原型模,试验模---prototype mold环境温度---ambient temperature⽌流阀---shut-off valve孔隙,空洞,⽓泡---void放电---discharge全压式模具---positive mold辅助压缸---auxiliary cylinder烫印---hot stamping,roll leaf stamping弯曲龟裂---flex cracking磨损---abrasion,wear磨耗---abrasion loss莫斯硬度---Mohs’hardness退⽕---annealing回⽕---tempering杨⽒弹性系数---Young’s modulus of elasticity 油压增压器---hydraulic intensifier 油压机---hydraulic press油压马达---hydraulic motor焊接---welding内衬,衬套,衬垫---liner流道,流道料---runner合模销,导销---leader pin合模销套,导销衬套---leader pin bushing回程销, 覆归销---return pin冷却⽔通路---cooling channel常温成形,冷模压---cold molding⽼化试验---ageing test对位圈,定位环---locating ring熔合线,结合线---weld line⾁厚---wall thickness脱模斜度---draft angle母模---cavity side顶出销,顶针---ejector pin分模线---parting line浇⼝,灌点---gate竖浇道---sprue浇道,流道---runner模仁,雄模,模⼼---core side浇⼝⽩晕---gate bush凹痕,缩痕,缩⽔---sink mark银线---silver line隧道形浇⼝---tunnel gate沉陷式浇⼝,潜⼊式浇⼝---submarine gate针孔形浇⼝---pin point gate注道形浇⼝,直接浇⼝---sprue gate⽑边形浇⼝,薄膜形浇⼝---flash gate,external ring gate,internal ring gate喷流,喷射现象---jetting剥料板---stripper plateMould components & AccessoriesMould base 模胚Bolts 螺栓Mould frame 模架screw 螺丝Top clamp plate ⾯板Stripper screw 脱料螺丝Bottom clamp plate 底板 F.H.C. screw（flat head cap screw）平头螺丝Socket head sountersunk screws 平头螺丝Hot runner plate 热流道板S.H.C. screw( socket head cap screw) 杯头螺丝Runner plate ⽔⼝板hexagonal socket head cap screw 杯头螺丝A plate A板Hexagonal head screw 六⾓头螺丝B plate B板Grub screw ⽆头螺丝（等⾼螺丝，基⽶螺丝）Stripper plate 推板Ball screw 波仔螺丝Support plate ⽀撑板Shoulder screw 限位螺丝（带肩螺丝，塞打螺丝）Spacer plate ⽅铁latch 插销Ejector retainer plate 顶针⾯板baffle 隔⽔⽚Ejector plate 顶针板plugs 喉塞Insulating plate 隔热板Jiffy plugs 喉咀Cavity 前模o-ring 密封圈Cavity insert 前模镶件Cooling tube 散热管Core 后模spring 弹簧Core insert 后模Support pillar 撑头Slide ⾏位Stop pin 垃圾钉Slide insert ⾏位镶件Dowel pin 管钉jaw ⾏位压块Spacer ring/washer 间隙圈Slide wear plate ⾏位耐磨块Venting slots 排⽓槽Slide guide block ⾏位导向块thermocouple 电热偶Slide lock ⾏位锁/⾏位扣Thermocouple connector 接线盒Wedge block 铲机Limit switch 限位开关W.B. wear plate 铲机耐磨块probe 探针Core pin 镶针Pry bar slots 开模槽Angle pin 斜导柱Safety strap 模锁Angle lifter 斜顶Lifting eye bolt 吊环（⽅向已固定）Lifter guide block 斜顶导向块Hydraulic cylinder 油缸Lifter base 斜顶座Air cylinder ⽓缸Press block 模料挤紧块Hydraulic motor 马达hoist ring 吊环（可转动⽅向）Knock out hole 顶棍孔Parting lock 树脂开闭器（尼龙扣）Name plate 铭牌Straight side interlocks T型锁（直⾝锁）Date code ⽇期印Tapered interlocks 斜度锁Cavity number 模⽳号sensor 感应器engrave 刻字/凹⼊heater 加热器Raised out 凸出K.O. insert 顶棍孔镶件Gate type & runnerDrop gate 点⽔⼝Sprue bushing 唧嘴Pin point gate 细⽔⼝Sprue/gate 浇⼝Edge/side gate 边⽔⼝Center sprue/sprue gate 中⼼进胶/直浇⼝runner shut off 流道开关/转⽔⼝Sub gate 潜⽔⼝Runner lock pin ⽔⼝扣针Tunnel gate 隧道浇⼝Puller 拉钩Ring gate 环形浇⼝Sprue lock pin 拉料杆Fan gate 扇形浇⼝Slag well 冷料井Valve gate 针阀式⽔⼝Banana gate ⾹蕉⽔⼝Guide＆Locating systemGuide pin/leader pin 导柱Grinder研磨机Crane 天车（吊车）Guide bushes 导套Grinding machine 磨床Groover machine 开槽机locating ring 法兰Lathe machine 车床Radial drill摇臂钻床EGB( ejector guide bush) 中托司Milling machine 铣床Wire cut machine 线割机Ejecting system Ejector pin 顶针Gear 齿轮Stepped ejector pin 有托顶针Rack 齿条Blade ejector 扁顶针Bearing 轴承Ejector bar 顶块Roller bearings 滚珠轴承Sleeve 司筒Retraction spring 复位弹簧Stripper plate 推板Return pin 回针Unscrewing 脱螺纹Two-stage ejector ⼆次顶出Ejector retainer plate 顶针⾯板chain 链条Ejector plate 顶针板Chain wheel 链轮Stop block 限位块key 键Ejector bushes 顶针套Specification of Injection Moulding MachineDiameter of the location ring 法兰直径Nozzle radius 机嘴半径Nozzle injection hole diameter 机嘴注射孔直径Depth for the nozzle into the mould 机嘴进⼊模具的深度KO hole distance KO孔间距fine thread 细螺纹Rough thread 粗螺纹mould opening distance 开模距离mould thickness 模具厚度tie bar distance Tie Bar 距离Injection defectsflash 披锋Warpage/deformation 变形Ejected mark 顶⽩Step 断差/台阶Weld line 熔接线Short shots 短胶Sink mark 缩⽔Sharp corner 尖⾓Gas trapped 困⽓Sharp edge 尖边Scratch marks 拖花Air bubble ⽓泡Kiss off 碰穿Short shot 短射(⽋充填)Shut off 擦穿位Flow mark 流纹Sticking cavity 粘前模Sticking core 粘后模Mould designplastic 胶位radius 半径Draft angle 拔模⾓Diameter 直径Fillet/ inside radius 圆⾓Inner diameter/I.D. 内径Outside radius 外转⾓Outer diameter/O.D. 外径Sprue bush radius 机嘴球半径boss 柱位Corner radius 转⾓半径Rib ⾻位Part drawing 产品图hole 孔Mould drawing 模图Pre-hardened steel 预硬钢Plastic material 胶料Through hardened steel 全硬钢Parting line 分型⾯Filling uneven ⾛胶不平衡Plastic thickness 胶厚Balanced runner 平衡⽔⼝系统Shrinkage rate 缩⽔率Cycle time 循环周期Surface treatmentEDM ⽕花纹Demoulding polish 脱模抛光High polish ⾼抛光Medium polish 中抛光Optical/mirror polish 镜⾯抛光chrome 镀铬Texture 蚀纹。
注塑专业英语词汇1
专业英语---注塑成型专业词汇Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力non-return valve 止回阀shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure/packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比mold close time 合模时间Resin 胶料Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重Elongation 延伸率density 密度melting point 熔点Polystyrene 聚苯乙烯（PS）Styrene 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethylene 聚乙烯glass fiber 玻纤Condensation 凝固，浓缩crystalline resin 结晶形塑料Mold materials 模具General-purpose steel 多用途钢tool steel 模具钢Free-cutting steel 高速切削钢case hardening steel 表面硬化钢Pre-hardened steel 预硬钢ball and roller bearing steel 滚珠轴承钢Nonferrous steel 非铁合金high speed steel 高速钢cast iron 铸铁Steel specification 钢材规格steel certification 钢材合格证明书Stainless steel 不锈钢nickel 镍chrome 铬aluminum 铝Copper 铜brass 黄铜bronze 青铜titanium 钛Processing 钢材的加工方法Harding / quench 淬火nitride 氮化temper 回火anneal 退火Roll 轧制abrasive 研磨，磨损的finish 精加工，抛光（polish）Case-hardening 表面硬化milling machine 铣（锣）床Lathe车床drill 钻床wire cut 线割NC(numerical control ) 数控材料EDM (Electrical discharge machine) 电火花加工Cut steel 开料Precision ground 精密研磨heat treatment 热处理tap 丝锥，攻牙Texture 蚀纹weld 焊接forge 锻压deformation 变形Spraying 喷涂die-cast 压铸Properties 性能Resistance 电阻，抵抗能力abrasion / wear磨损erode / corrode 腐蚀 Toughness 韧性yield strength 屈服强度tensile strength 拉伸强度Fatigue strength 疲劳强度break 断裂stress 应力 hardness 硬度Humidity / moisture 潮湿，湿气roughness 粗糙度parameter 参数Thermal conductivity 导热系数manufacture 制造，加工drawback 缺点Ductility 延展性grain 晶粒property 性能，财产brittleness 脆性GD&T （Geometric Dimensions and Tolerance ）形位尺寸公差 Flexural strength 挠曲强度impact 冲击conductivity 传导性，导电性Optical 光学的transparent 透明的insulation 绝缘Mechanical 机械的processability 可加工性能timeyield 蠕变Physical 物理的flow rate 流动速率compressive strength 压缩强度Adhesive 粘附的，胶合durability 耐用性Mold design 模具设计Tooling specification 模具规格mould flow 流动模拟sprue nozzle 唧咀孔Clearance 避空，间隙undercut 倒扣flush 插入，埋入legend 图例Groove 凹槽latch 插销class 类型，种类plan 平面图Orifice 孔，口column 柱位boss 凸台standard 标准，规格 Rib 骨位tapered interlock 锥形管位块Bubbler 炮隆Bolt 螺钉，销顶identification mark 铭牌P/L strip 锁模片Overflow well / cold-slug well 冷料井Vent 排气pocket 槽Gate location 入水点full line 实线broken line 虚线Retainer 固定，支撑operator 操作者（啤工）receptacle 插座Lifting hole 吊令孔insulation plate 隔热板cavity number 型腔号Bolster 支撑，垫子vent channel 排气槽leak / filter 渗漏 Leak test 试运水stamp / engrave 雕刻，印记（打字唛）Clamp slot 码模槽support button / pin 垃圾钉cut steel 开料Lodge 安装，放置inlay 镶嵌，插入cam / lifter 斜顶Stripper推方lifting bar 吊模方sprue 唧咀tolerance 公差Counter bore 沉孔slant 倾斜，斜面conical 圆锥的，圆锥形的Bolt 螺栓manifold 热流道板prototype tooling 原型试验 Gusset 角撑reverse mold 倒装模constrain / restrict约束，限制Counter lock 反锁thermocouple 热电偶moldmaker 模具制造商Asset / property number 资产编号tool product destination 模具生产地点Accelerating ejection 加速顶出hydraulic 液压的pneumatic 气动的Trapezoid 梯形的semi-round 半圆形format 格式baffle 隔水片Electrode 电极，铜公spare part 配件gall 磨伤，插伤 Cable 电缆，电线plating / coating （电）镀bonding / joint 接头Wall transition 壁厚过渡Product problem 产品问题Troubleshoot 故障处理reduce(add) plastic 减（加）胶Burr/flash披峰 Burn mark 烧焦ejector mark 顶针印，顶白black specs 黑点，黑斑Discoloration 混色，污点gloss 光泽jetting/worming 走水纹Sink mark 缩水void / bubble 气泡，夹气distortion 变形Warpage 翘曲short molding / non-fill缺胶，未走齐Weld line / knit line 夹水线discarded as useless 报废Split line 夹线stick in sprue bushing / cavity / core 粘唧咀/前模/后模Break / crack 顶裂brittleness 脆性，易脆Others 其他Invoice 发票，清单vendor(er) 卖方vendee 买方guideline 方针，指导Intricate 复杂的confidential 机密的，不可外泄的proprietary 私有的Authorize 批准，授权recipient 接收者issue ①发布，提供；②问题Approve 确认，赞成requirement 需要，必需物const 常数，常量Regarding 关于，涉及opposite 相反的，对面的latitude 纬度，纵向的Version 版本definition 注释，解说transversal 横向的，截线Profile 轮廓，剖面eliminate / cancel 取消allow / permit 允许，许可Respective 各自的，分别的individual 单独的decrease 减少increase 增加Preliminary 初步的approximately 大约，近似estimate / valuate估计，预算Adjust 调整，校准application 应用，申请maintain 维持Accurate / precise 精确的smooth 光滑，顺畅的device 装置，设备Convenient 方便的deadline 截至日期available 有用的，有空的Shift 轮班，换班critical 关键的，临界的exceptional 异常的，优异的Exceed 超过layout 布局，方案loss 损失，消耗install 安装，安置Rotation 旋转item 条款，项目quotation 报价stabilize 稳定Quality 质量quantity 数量couple 连接，接合configuration 构造，外形Illustrate 图解说明simulation 模拟，仿真recommend 推荐使用。
塑料机械类常用英语(一.组装、冲压、喷漆等专业词汇)
Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床|刨床 planer |'pleinmiller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良n|氧化 oxidation |' ksi'deiscratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑。
塑料加工专业英语
塑料加工专业英语
Plastic Processing专业英语是指与塑料制品的加工工艺、产品设计、设备和工艺参数等相关的英语词汇和表达方式。
下面是一些相关的塑料加工专业英语词汇和表达方式：
1. Injection molding 注塑成型
2. Extrusion 挤出
3. Blow molding 吹塑
4. Rotational molding 旋转成型
5. Thermoforming 热成型
6. Compression molding 压缩成型
7. Calendering 挤压
8. Plasticizing 熔化
9. Melt temperature 熔融温度
10. Injection pressure 注塑压力
11. Cooling time 冷却时间
12. Mold cavity 模腔
13. Ejector pin 弹簧顶杆
14. Gate sprue 浇口
15. Runner system 平衡道
16. Mold release agent 脱模剂
17. Plasticizer 增塑剂
18. Reinforcement 增强剂
19. Melt flow index 熔体流动指数
20. Mold shrinkage 模具收缩率
这些词汇和表达方式可以帮助从事塑料加工专业的人更好地理解和沟通相关的技术和工艺要求。
塑料件词汇
Project瑕疵常用词汇bla涂料疤bli起泡blo起霜blo破孔blu泛白bo侧壁皱纹br冒口带肉bu膜泡bu糊斑bu毛边ca翘曲ce气泡ce表面中部波皱ch细裂痕ch龟裂ch修整表面缺陷cla铸件凹痕co塌陷co色斑co腐蚀cra裂痕cra碎裂crazing 龟裂de变形ed切边碎片ed裂边fad退色fill填充料斑fis裂纹fla凸缘起皱fla刮伤flo流痕ga毛边gla光滑glo光泽gr污斑gr磨痕ha发裂ha雾度inc水锈ind压痕int内部气孔mi偏模mo斑点ne缩颈nic割痕or橘皮状表面缺陷ov溢流pe剥离pit坑pit点状腐蚀pla模板印痕po麻点po痘斑re树脂流纹re树脂脱落rid凹陷 sagging 松垂sa皂化sc疤痕sc废料sc废料阻塞sc刮伤/划痕sc深冲表面划伤se裂痕sh模口挤痕sh充填不足sh凹孔sin凹痕sk表皮折迭str矫直str条状痕su表面裂痕su橘皮状表皮皱折su波动sw冒汗tor扭曲wa翘曲wa波痕we熔塌we焊痕wh白化wr皱纹mi漏件wr错件ex过多的缺陷cri极严重缺陷ma主要缺陷mi次要缺陷no不合规格dim尺寸偏大(小)co外观不良sli螺丝滑头sli滑手sp斑点mi发霉ru生锈de变形bu金属)fla塑件)毛边po铆合不良ex间隙过大gr油污inc杂质pa脏污sh缩水mi杂色sc划伤po制程不良po事件不良fol打包带折皱pa补漆dis羿色wa水渍流道浇口部分fan扇形浇口sid侧浇口ed侧缘浇口tab搭接浇口film薄膜浇口fla闸门浇口sli缝隙浇口dis盘形浇口dia隔膜浇口rin环形浇口Ru无浇道(sp无射料管方式lon延长喷嘴方式sp浇口;溶渣ins热浇道ru浇道模块va阀门浇口 slag well 冷料井co冷料渣sp射料浇口，直浇口no射嘴sp料头钩销(拉料杆)inj注塑模ru橡胶成形ho热室压铸sa砂模铸造ex挤出模mu多模穴模具pa叠层模pla石膏模thr三板模pla简易模pie冲孔模公模注塑缺陷sp银纹sh短射sin缩痕str条纹vo缩孔we熔接线ga烧焦co冷斑de起皮bu毛刺fla刮伤glo光泽gla光滑 surface check 表面裂痕he迟滞注塑工艺:mo成型条件dr烘干Machinegr磨床dr钻床lin线切割ele电火花we电焊机pu冲床ro机械手co常用设备ED放电加工3D三次元量床 boring machine 搪孔mi铣床co轮廓锯床co仿形磨床cy外圆磨床die合模机en雕刻机检验量测工具用语cy圆筒直尺de测深规dia针盘指示表dia卡规dig数位式测微计fee测隙规ga量规定位板he测高规ins内卡钳ins内分卡int干涉仪 leveling block 平台lim限规mi测微计mi千分之一寸mo压力计mo莫氏锥度量规no游标卡尺op光学平晶op光学平行pa内径仪po位置刻度pr轮廓光学投影仪pr分角器ra半径rin环规sin正弦量规sn卡模sq直角尺sty触针tel伸缩性量规wo工作量规ac乙炔焊接用语ha硬表面堆焊jig工模焊接las雷射光焊接me熔接nu点焊熔核ov堆焊pe珠击熔接法plu塞孔熔接po正向熔接pr压焊pr丙烷气切割pu纯镍熔接条 reinforcement of weld 加强焊re抗蚀护膜ro背面熔接se焊缝se接合se流缝熔接se串联缝熔接sk跳焊法sp火花sp点焊接sti针角焊接stu电弧焊接un下部焊层vo焊接空隙we焊接流痕we焊缝凸起we焊接纹we焊接痕we熔接透入we焊接区we焊接塑胶原料en工程塑胶ep环氧树脂EPeth乙基纤维素eth乙烯-醋酸乙烯EVAeth醋酸乙烯共聚物EVAfib纤维强化热固性/纤维强化复合材料hig高密度聚乙烯HDPEhig高冲击聚苯乙烯HIPShig高冲击性聚苯乙烯low低密度聚乙烯LDPEme三聚氰胺酚醛树脂MFnit硝酸纤维素ph酚醛树脂pla塑胶po聚丙烯酸PAPpo耐龙PApo聚对苯二甲酸丁酯PBTpo聚碳酸酯PC polyethyleneglycol 聚乙二醇PFGpo聚氧化乙烯PEOpo聚乙醇对苯PETPpo聚甲基丙烯酸甲酯PMMApo聚缩醛POMpo聚硫化亚苯po聚苯醚PPOpo聚丙烯PPpo聚苯乙烯PSpo聚四氟乙烯PTFEpo聚四氟乙烯po聚乙烯PEpo聚氨基甲酸酯PUpo聚醋酸乙烯PVACpo聚乙烯醇PVA表面处理关连用语an阳极氧化处理ato阿托木洛伊表面au奥氏体等温淬火au奥斯田体/奥氏体ba贝氏体ba条纹状组织ba滚镀ba滚筒打光bla染黑法blu青熟脆性bo磷酸盐皮膜处理bo箱型退火bo封箱渗碳br辉面电镀br光辉热处理by旁路热处理ca炭化物ca浸碳硬化深层ca渗碳ce炭化铁ch化学电镀ch化学蒸镀co结晶粒粗大化co涂布被覆co低温脆性co渗碳体co大气热处理co锐角效应cre蠕缓放电de脱碳处理de脱碳退火de硬化深层dif扩散dif扩散退火ele电解淬火em压花etc表面蚀刻fer肥粒铁firs第一段退火fla火焰硬化fla火焰处理ful完全退火ga气体氧化法glo球状炭化铁gr结晶粒度gr磷酸溶液热处理gr石墨退火ha硬化性ha硬化性曲线ha硬化he热处理ho热浴淬火ho热浸镀ind高周波硬化ion离子渗碳氮化ion离子渗碳处理ion离子电镀iso等温退火liq液体喷砂法low低温退火ma可锻化退火ma麻回火处理ma马氏体/硬化铁炭 metallikon 金属喷镀法me真空涂膜nit氮化处理nit软氮化no正常化oil油淬化ov过老化ov过热pe针尖组织ph磷酸盐皮膜处理ph物理蒸镀pla离子氮化pr预备退火pr析出pr析出硬化pr加压硬化pr制程退火qu淬火老化qu淬火qu淬火裂痕qu淬火变形qu淬火应力re再调质re再结晶re红热脆性re残留应力re残留奥ru防蚀sa盐浴淬火sa喷砂处理se时效处理se第二段退火se经年变形se偏析se部分淬火sh喷丸处理sh珠击法sin等温渗氮sin烧结处理so均热处理so软化退火so固溶化热处理sp球状化退火sta安定化处理str矫直退火str应变老化str应力消除退火su生冷处理su过冷su表面硬化处理tem回火脆性tem回火颜色tem回火tem回火裂痕tex咬花the调质处理the加工热处理tim时间淬火tra变态tuf软氮化处理un不完全退火va真空渗碳氮化va真空渗碳处理va真空淬火va真空热处理va真空氮化射出成形关联用语cry不透明度仪da开隙dr空料试车周期时间du延性ela弹性体ex压出粒涂层法fee供料fill充填剂film薄膜吹制法flo活动模板foa发泡剂glo光泽gr颗粒料gu料斗ho热斑ho烫印inj射出喷嘴inj射出柱塞 injection ram 射出冲柱iso同分异构物kn混合机lev匀涂剂lub润滑剂ma配合成形法mo锁模力mo脱模剂no喷嘴or取向薄膜pa吹气成形坏料pe粒料pla可塑剂plu压料柱塞po孔隙率po后固化pr预混料pu清除re往复螺杆re回弹性re树脂射出法rh流变学sh塑胶片sh注射sh射出循环sli光滑剂tak取料装置tie拉杆tog肘杆式锁模装置tor鱼雷形分流板tra透明性成形不良用语ce表面中部波皱ch细裂痕ch龟裂ch修整表面缺陷cla铸件凹痕co塌陷co色斑co腐蚀cra裂痕cra碎裂cra龟裂de变形ed切边碎片ed裂边fad退色fill填充料斑fis裂纹fla凸缘起皱fla刮伤flo流痕ga毛边gla光滑glo光泽gr污斑gr磨痕ha发裂ha雾度inc水锈 indentation 压痕int内部气孔mi偏模mo斑点ne缩颈nic割痕ra橘皮状表面缺陷ov溢流pe剥离pit坑pit点状腐蚀pla模板印痕po麻点po痘斑re树脂流纹re树脂脱落rid凹陷sa松垂sa皂化sc疤痕sc废料sc废料阻塞sc刮伤/划痕sc深冲表面划伤se裂痕sh模口挤痕sh充填不足sh凹孔sin凹痕sk表皮折叠str矫直str条状痕su表面裂痕su橘皮状表皮皱折su波动tor扭曲wa翘曲模具常用刀具工作法用语co凹面铣刀co凸形铣刀cro十字接头cu刃口余隙角dr钻台ed刃用锉刀file锉刀fla凸缘接头gr砂轮机ha铁锤ha手摇钻ha剖面线he六角头螺栓he六角螺帽ind分度头jac千斤顶jig治具kit工具箱 lapping 研磨me金工锯no刀角pin钳子pli铗钳 plug 柱塞头po磨光器pr手提钻孔机pu冲头sa砂纸sc刮刀sc螺丝起子sc划线se中纹锉sp扳手sp方栓槽拉刀各种冲模加工关连用语bla下料加工bu撑压加工bu冲缘加工ca凸轮弯曲加工co压印加工co压缩加工co押弯曲加工cro凸面加工cu卷边弯曲加工cu卷曲加工cu切削加工din切断蕊骨do叠板裁断dr引伸加工dr抽引光滑加工em浮花压制加工ex挤制加工fili锉削加工fin精密下料加工fin光制下料加工fin精整加工fla凸缘加工fol折边弯曲加工fol折叠加工for成形加工im冲击挤压加工ind压痕加工iro引缩加工 knurling 滚花loc固定接合lou百叶窗板加工ma刻印加工ne颈缩加工no冲口加工pa分断加工pie冲孔加工pr连续弯曲加工pr连续下料加工pr连续引伸加工pr连续成形加工re铰孔加工re二次精冲加工riv铆接加工ro滚筒弯曲加工ro滚压加工ro压延加工ro粗加工sc无废料加工se折弯重叠加工冲压机械及周边关连用语ca铸包ch烧磨砂ch加料漏斗cle间隙clo合模锻造clu夹紧clu离合器clu离合器制动器clu离合器轮壳clu离合器覆盖co带卷升降运输机co卷材进料装置co钢材卷料架co圆柱co连杆调节螺钉co砂心黏结剂co对击锻锤cra送料架cra曲柄轴cra无曲柄式cro横向曲轴cu缓冲de外缩凹孔dia分度送料die模口角度die合模die模具缓冲垫die冲压闭合高度die模具寿命die母模逃孔die调整冲模用压力机do双曲柄轴冲床dr逃料倾斜角ed边锻伸em加装砂心fee送料长度fee送料高度fill埋入砂心fill填砂film液面花纹fin精密下料冲床for辊锻机fin炼后熔渣fly飞轮fly飞轮制动器foo脚踏冲床for进模口板fra床身机架fric摩擦fric摩擦煞车ga凹口剪床ge齿轮gib滑块引导部gr夹具gr夹持进料gr夹紧传送装置ha槌机ha手动冲床ha手动齿轮齿条式冲床ha手动螺旋式冲床ho料斗送料 idle stage Idle Station 空站inc微调尺寸iso恒温锻造ke键槽离合器kn脱模装置kn转向机构lan模具直线刀面部loa供料器un卸料机loo闭回路控制器low下模mi微寸动装置mi微动装置mo活动工作台no冲缺口压力机op排料逃孔ov防超载装置pin导正滚轮pin小齿轮pit节距pr压入pr连续送料pu推杆式送料pu料片押片装置qu快速换模系统re再次研磨re松释动作re反转下料ro机器人ro辊轧成形ro辊轧成形机ro脱辊ro辊式送料ro辊式矫直机ro卷弯成形机sa安全保护装置sc废料切刀sc废料冲床se无缝锻造sh崩砂sh剪角sh薄板装料机sh单行程工作sh收缩配合sh闭合高度sie筛孔sin铸砂烧贴sli滑动平衡器slu逃料孔sp旋压成形机sp合模sta堆叠拨送料机线切割放电加工关连用语ar电弧放电Itermsjack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具defective product label不良标签identifying sheet list标示单screwdriver holder起子插座aberration 色差atomization 霚化bank mark 滞料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷 sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位qualified products up-to-grade products良品defective products not up-to-grade products不良品waste废料runner system浇道系统sprue/cold material trap 浇道/冷料井sprue puller 拉杆runner design 流道设计main runner 主流道secondary runner 次流道gate design 浇口设计submarine gate 潜伏浇口tunnel gate 隧道式浇口pinpoint gate 点浇口fan gate 扇形浇口side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口dish gate 盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣insulated runner/hot runner 热浇道runner plat 浇道模块valve gate阀门浇口 slag well 冷料井cold slag 冷料渣sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) injection mold 注塑模rubber molding 橡胶成形hot chamber die casting 热室压铸sand mold casting 砂模铸造extrusion mold 挤出模multi-cavity mold 多模穴模具palletizing die 叠层模plaster mold 石膏模three plates mold 三板模plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心flash 飞边warpage 翘曲air trap 积风blush 发赤flow line 流痕splay 银纹short shot 短射sink mark 缩痕streak 条纹void 缩孔weld line 熔接线gas mark 烧焦cold slug 冷斑delamination 起皮burr 毛刺flaw/scratch 刮伤gloss 光泽glazing 光滑 surface check 表面裂痕hesitation 迟滞注塑工艺:molding conditions 成型条件drying 烘干barrel temperature 料筒温度melt temperature 熔化温度mold temperature 模具温度injection pressure 注塑压力back pressure 背压injection speed 注塑速度screw speed 螺杆转速tensile strength 抗拉强度tensile elongation 延伸率flexural modulus 弯曲模数flexural strength 抗弯强度shrinkage 收缩率regrind usage 次料lathe车床planer |刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机punching machine 冲床robot机械手common equipment常用设备EDM=Electron Discharge Machining 放电加工3D coordinate measurement 三次元量床 boring machine 搪孔机milling machine 铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床cylindrical grinding machine 外圆磨床die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床autocollimator 自动准直机bench comparator 比长仪block gauge 块规bore check 精密小测定器calibration 校准caliper gauge 卡规check gauge 校对规clearance gauge 间隙规clinoretee 测斜仪comparator 比测仪cylinder square 圆筒直尺depth gauge 测深规dial indicator 针盘指示表dial snap gauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge 测高规inside calipers 内卡钳inside micrometer 内分卡interferometer 干涉仪 leveling block 平台limit gauge 限规micrometer 测微计mil 千分之一寸monometer 压力计morse taper gauge 莫氏锥度量规nonius 游标卡尺optical flat 光学平晶optical parallel 光学平行passimeter 内径仪position scale 位置刻度profile projector 轮廓光学投影仪protractor 分角器radius 半径ring gauge 环规sine bar 正弦量规snap gauge 卡模square master 直角尺stylus 触针telescopic gauge 伸缩性量规working gauge 工作量规acetylene 乙炔ampere 电流安培angle welding 角焊arc 电弧argon arc welding 氩弧焊接bare electrode 光熔接条butt welding 对接焊接camber 电弧弯曲cascade 阶叠熔接法clad weld 被覆熔接crator 焊疤excess metal 多余金属filler rod 焊条fillet weld 填角焊接gas shield 气体遮蔽groove welding 起槽熔接hand face shield 手握面罩hard facing 硬表面堆焊jig welding 工模焊接laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法plug welding 塞孔熔接positioned welding 正向熔接pressure welding 压焊propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条 reinforcement of weld 加强焊接resist 抗蚀护膜root running 背面熔接seam 焊缝seaming 接合seam welding 流缝熔接series seam welding 串联缝熔接skip welding process 跳焊法spark 火花spot welding 点焊接stitch welding 针角焊接stud arc welding 电弧焊接under laying 下部焊层void 焊接空隙weld flow mark 焊接流痕weld flush 焊缝凸起weld line 焊接纹weld mark 焊接痕weld penetration 熔接透入weld zone 焊接区welding 焊接welding bead 焊接泡welding direction 焊接方向welding distortion 焊接变形welding flux 焊剂welding ground 电熔接地welding interval 焊接周期welding stress 熔接应变welding torch 熔接气炬acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CAcellulose acetate butyrate 醋酸丁酸纤维素CABcomposite material 复合材料cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑胶epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer 乙烯-醋酸乙烯EVA ethylene-vinlacetate copolyme 醋酸乙烯共聚物EVAfiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPEmelamine resin 三聚氰胺酚醛树脂MFnitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑胶polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PApolybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POMpolyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPOpolypropylene 聚丙烯PPpolystyrene 聚苯乙烯PSpolytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PEpolyurethane 聚氨基甲酸酯PUpolyvinylacetate 聚醋酸乙烯PVACpolyvinylalcohol 聚乙烯醇PVApolyvinylbutyral 聚乙烯醇缩丁醛PVBpolyvinylchloride 聚氯乙烯PVCpolyvinylfuoride 聚氟乙烯PVFpolyvinylidenechloride 聚偏二氯乙烯PVDCprepolymer 预聚物silicone resin 硅树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树脂age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿托木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭 metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理activator 活化剂bag moulding 气胎施压成形bonding strength 黏合强度breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 着色剂color matching 调色color masterbatch 色母料compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动模板foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞 injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 后固化premix 预混料purging 清除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑胶片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率aberration 色差bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷。
模具塑料英语
模具词汇英语翻译(塑件与模具)compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣。
塑料模具专业英语词汇
分类：塑胶模具模具英语词汇表Aabrasive grinding 强力磨削 L3 abrasive[E'breisiv] a.磨料的, 研磨的 L2,3 absence ['AbsEns] n.. 不在，缺席 L17accesssory[Ak'sesEri] n.附件 L10accommodate[E'kCmEdeit] v. 适应 L5accordingly[E'kC:diNli] adv.因此,从而,相应地 L7,13 accuracy['AkjurEsi] n精度,准确性 L1,3actuate['Aktjueit] vt.开动(机器), 驱动 L8adequate['Adikwit] a. 足够的 L13adhesive[Ed'hi:siv] n. 粘合剂 L22adjacent[E'dVeisnt] a. 邻近的 L13adopt[E'dCpt] vt. 采用 L4advance [Ed'vA:ns] n.进步 L7advisable [Ed'vaizbl] adj. 可取的 L20agitate['AdViteit] v. 摇动 L2a large extent 很大程度 L4,13algorithm ['Al^EriTEm] n. 算法 L6align [E'lain] v 定位，调准 L17alignment[E'lainmEnt] n. 校直 L11all-too-frequent 频繁 L17allowance[E'lEuens] n. 容差, 余量 L5alternate['C:ltEnit]v.交替,轮流 L1alternative[C:l'tE:nEtiv] n. 替换物 L3alternatively[C:l'tE:nEtivli] ad. 做为选择, 也许 L5 aluminiun[7Alju'minjEm] n.铝 L2ample['Ampl] adj. 充足的 L20analysis [E'nAlEsis] n. 分析 L6ancillary['AnsilEri] a.补助的, 副的 L4angular ['A^julE] adj. 有角的 L20annealing[E'li:liN] n.退火 L2aperture ['ApEtFE] n.孔 L17applied loads 作用力 L1appropriate [E'prEuprieit] a. 适当的 L6,20arc[a:k] n.弧, 弓形 L10arise[E'raiz] vi. 出现, 发生 L21arrange[E'reidV] v. 安排 L12article['a:tikl] n.制品, 产品 L21ascertain[7AsE'tein] vt. 确定, 查明 L1assemble[E'sembl] vt.组装 L4attitude ['Atitju:d] n 态度 L17auxiliary [C:^'ziljEri]adj. 辅助的 L8avoid[E'vCid] v.避免 L7axis['Aksis] n.轴 L5axle['Aksl] n.轮轴, 车轴 L1Bbackup['bAk7Qp] n. 备份 L9batch [bAtF] n 一批 L17bearing['bZEriN] n.轴承,支座 L21bed[bed] n. 床身 L5behavior[bi'heivjE] n. 性能 L1bench-work 钳工工作 L4bend[bend] v.弯曲 L1beneath[bi'ni:W] prep在···下 L4bin [bin] n. 仓，料架 L19blank [blANk] n. 坯料 L20blank [blANk] v. 冲裁,落料 L17blanking tool 落料模 L17blast [blQst] n.一阵（风） L18blemish['blemiF] n. 缺点, 污点 L13bolster['bEulstE] n. 模座,垫板 L4,5boost[bu:st] n. 推进 L9boring['bC:riN] n.镗削, 镗孔 L4,5bracket ['brAkit] n. 支架 L19brass [brAs] n.黄铜 L2break down 破坏 L1breakage ['breikidV] n.破坏 L17bridge piece L16brine[brain] n. 盐水 L2brittle['britl] adv.易碎的 L1buffer [bQfE] n.缓冲器 L8built-in 内装的 L9bulging [bQldViN] n. 凸肚 L22burr [bE:] n. 毛刺 L17bush [buF] n. 衬套 L17bush[buF]n. 衬套 L5by far (修饰比较级, 最高级)···得多, 最 L3 by means of 借助于 L5Ccabinet ['kAbinit] n.橱柜 L7call upon 要求 L17carbide['ka:baid] n.碳化物 L10carburzing['ka:bjuretiN] n. 渗碳 L2 carriage['kAridV] n.拖板, 大拖板 L5carry along 一起带走 L18carry down over 从···上取下 L21carry out 完成 L17case hardening 表面硬化 L2case[keis] n. 壳, 套 L2cast steel 铸钢 L17casting['ka:stiN] n. 铸造,铸件 L3category['kAtE^Euri] n. 种类 L6,15caution ['kC:FEn] n. 警告，警示 L17cavity and core plates 凹模和凸模板 L11cavity['kAviti] n.型腔, 腔, 洞 L4,10centre-drilling 中心孔 L5ceramic[si'rAmik] n.陶瓷制品 L3chain doted line 点划线 L11channel['tFAnl] n.通道, 信道 L8characteristic[kArEktE'ristik] n.特性 L1 check[tFek] v.核算 L21chip[tFip] n.切屑, 铁屑 L3chuck [tFQk] n.卡盘 L5,8chute [Fu:t] n. 斜道 L19circa ['sEkE:] adv. 大约 L7circlip['sE:klip] n.(开口)簧环 L22circuit['sE:kit] n. 回路, 环路 L13circular supoport block L5circulate['sE:kjuleid] v.(使)循环 L13clamp [klAmp] vt 夹紧 L17clamp[klAmp] n.压板 L12clay[klei] n. 泥土 L2,7clearance ['kliErEns] n. 间隙 L17clip [klip] vt. 切断，夹住 L19cold hobbing 冷挤压 L4cold slug well 冷料井 L12collapse[kE'lAps] vi.崩塌, 瓦解 L22collapsible[kE'lApsEbl] adj.可分解的 L22 combination [kCmbi'neiFEn] n. 组合 L18 commence[kE'mens] v. 开始, 着手 L16 commence[kE'mens]v. 开始 L21commercial [kE'mE:FEl] adj. 商业的 L7 competitive[kEm'petitiv] a. 竞争的 L9 complementary[7kCmpli'mentEri] a. 互补的 L5 complexity [kem'pleksiti] n.复杂性 L8 complicated['kCmplEkeitid] adj.复杂的 L2 complication [kCmpli'keiFEn] n. 复杂化 L5,20 compression [kEm'preFEn] n.压缩 L1comprise[kEm'prais] vt.包含 L16compromise['kCmprEmaiz] n. 妥协, 折衷 L13 concern with 关于 L6concise[kEn'sais] a. 简明的, 简练的 L9confront[kEn'frQnt] vt. 使面临 L14connector[kE'nektE] n. 连接口, 接头 L14 consequent['kCnsikwEnt] a. 随之发生的, 必然的 L3 console ['kCnsoul] n.控制台 L8consume [kEn'sjum] vt. 消耗, 占用 L7 consummate [kEn'sQmeit] vt. 使完善 L6container[kEn'teinE] n. 容器 L11contingent[ken'tindVEnt] a.可能发生的 L9contour['kEntuE] n.轮廓 L5,21conventional[kEn'venFEnl] a. 常规的 L4converge[kEn'vE:dV] v.集中于一点 L21conversant[kCn'vE:sEnt] a. 熟悉的 L15conversion[kEn'vE:FEn] n 换算, 转换 L7conveyer[ken'veiE] n. 运送装置 L12coolant['ku:lEnt] n. 冷却液 L13coordinate [kEu'C:dnit] vt. (使)协调 L8copy machine 仿形(加工)机床 L4core[kC:] n. 型芯, 核心 L2,4corresponding [ka:ri'spCdiN] n.相应的 L7 counteract [kauntE'rAkt] vt. 反作用,抵抗 L20 couple with 伴随 L20CPU (central processing unit) 中央处理器 L9 crack[krAk ] v.（使）破裂，裂纹 L1,17critical['kritikl] adj.临界的 L2cross-hatching 剖面线 L16cross-section drawn 剖面图 L11cross-slide 横向滑板 L5CRT (cathoder-ray tube) 阴极射线管 L9crush[krQF]vt.压碎 L1cryogenic[7kraiE'dVenik ]a.低温学的 L1crystal['kristl] adj.结晶状的 L1cubic['kju:bik] a. 立方的, 立方体的 L3cup [kQp] vt (使)成杯状, 引伸 L18curable ['kjurEbl] adj. 可矫正的 L20curvature['kE:vEtFE] n.弧线 L21curve [kE:v] vt. 使弯曲 L20cutter bit 刀头, 刀片 L3cyanide['saiEnaid] n.氰化物 L2Ddash [dAF] n. 破折号 L6daylight ['deilait] n. 板距 L12decline[di'klain] v.下落,下降,减少, L3,9deform[di'fC:m] v. (使)变形 L1,3demonstrate['demEstreit ] v证明 L21depict[di'pikt ] vt 描述 L18deposite [di'pCzit] vt. 放置 L20depression[di'preFEn] n. 凹穴 L12descend [di'sent] v. 下降 L20desirable[di'zairEbl] a. 合适的 L2detail ['diteil] n.细节，详情 L17deterioration[ditiEri:E'reiFEn] n. 退化, 恶化 L12 determine[di'tE:min] v.决定 L16diagrammmatic[7daiEgrE'mAtik].a.图解的，图表的 L10 dictate['dikteit] v. 支配 L12die[dai] n.模具, 冲模, 凹模 L2dielectric[daii'lektrik] n. 电介质 L10die-set 模架 L19digital ['didVitl ] n.数字式数字, a.数字的 L3,6 dimensional[dddi'menFEnl] a. 尺寸的, 空间的 L3 discharge[dis'tFa:dV] n.v. 放电, 卸下, 排出 L3 discharge[dis'tFa:dV] v.卸下 L8discrete [dis'cri:t] adj. 离散的,分立的 L7 dislodge[dis'lCdV] v. 拉出, 取出 L12dissolution[disE'lu:FEn] n.结束 L9distinct [dis'tiNkt] a.不同的，显著的 L6distort [dis'dC:t] vt. 扭曲 L20distort[dis'tC:t] vt. (使)变形, 扭曲 L1distributed system 分布式系统 L9dowel ['dauEl] n. 销子 L19dramaticlly [drE'mAtikli] adv. 显著地 L7drastic ['drAstik] a.激烈的 L17draughting[dra:ftiN] n. 绘图 L16draughtsman['drAftsmEn] n. 起草人 L16drawing['drC:iN] n. 制图 L11drill press 钻床 L8drum [drQm] n.鼓轮 L8dual ['dju:El] adv. 双的，双重的 L18ductility [dQk'tiliti ] n.延展性 L1,21dynamic [dai'nAmik ] adj 动力的 L6Eedge [edV] n .边缘 L20e.g.(exempli gratia) [拉] 例如 L12ejector [i'dVektE] n.排出器， L18ejector plate 顶出板 L16ejector rob 顶杆 L5elasticity[ilA'stisiti] n.弹性 L1electric dicharge machining 电火花加工L3 electrical discharge machining电火花加工 L10electrochemical machining 电化学加工L3 electrode[i'lektrEud] n. 电极 L10electro-deposition 电铸 L4elementary [elE'mentEri] adj.基本的 L2 eliminate[i'limineit] vt. 消除, 除去 L10 elongate[i'lCN^et] vt. (使)伸长, 延长 L1 emerge [i'mE:dV] vi. 形成, 显现 L20 emphasise['emfEsaiz] vt. 强调 L4endeavour[en'devE] n. 尽力 L17engagement[in'^eidVment] n. 约束, 接合 L22 enhance[in'hAns] vt. 提高, 增强 L9ensure [in'FuE] vt. 确保，保证 L17envisage[in'vizidV] vt.设想 L15erase[i'reis] vt. 抹去, 擦掉 L16evaluation[i'vAlju7eiFEn] n. 评价, 估价L1 eventually[i'vEntFuEli ] adv.终于 L21 evolution[evE'lu:FEn] n.进展 L16excecution[eksi'kju:FEn] n. 执行, 完成 L9 execute ['ekskju:t] v. 执行 L8exerte [i^'zE:t] vt. 施加 L20experience[iks'piriEns] n. 经验 L16 explosive[iks'plEusiv]adj.爆炸(性)的 L22 extend[eks'tend] v. 伸展 L2external[eks'tE:nl] a. 外部的 L5,11 extract[eks'trAkt] v. 拔出 L14extreme[iks'tri:m] n. 极端 L13extremely[iks'tri:mli] adv. 非常地 L12 extremity[iks'tmiti] n. 极端 L13extrusion[eks'tru:VEn] n. 挤压, 挤出 L3FF (Fahrenheit)['fArEnhait]n.华氏温度 L2fabricate ['fAbrikeit] vt.制作,制造 L7 facilitate [fE'siliteit] vt. 帮助 L6facility[fE'siliti] n. 设备 L4facing[feisiN] n. 端面车削 L5fall within 属于, 适合于 L15fan[fAn] n.风扇 L7far from 毫不, 一点不, 远非 L9fatigue[fE'ti^] n.疲劳 L1feasible ['fi:zEbl] a 可行的 L18feature ['fi:tFE] n.特色, 特征 L7,17feed[fi:d] n.. 进给 L5feedback ['fi:dbAk] n. 反馈 L8female['fi:meil] a. 阴的, 凹形的 L11ferrule['ferEl] n. 套管 L14file system 文件系统 L9fitter['fitE] n.装配工, 钳工 L4fix[fiks] vt. 使固定, 安装, vi. 固定 L11fixed half and moving half 定模和动模 L11flat-panel technology 平面(显示)技术 L9 flexibility[fleksi'biliti] n. 适应性, 柔性 L9 flexible['fleksEbl] a. 柔韧的 L13flow mark 流动斑点 L13follow-on tool 连续模 L18foregoing ['fC:'^EuiN]adj. 在前的,前面的L8foretell[fC:'tell] vt. 预测, 预示, 预言 L9 forge[fC:dV] n. v. 锻造 L3forming[fC:miN] n. 成型 L3four screen quadrants 四屏幕象限 L9fracture['frAktFE] n.破裂 L21free from 免于 L21Ggap[^Ap] n. 裂口, 间隙 L10gearbox['^iEbCks] n.齿轮箱 L5general arrangement L16govern['^QvEn] v.统治, 支配, 管理 L13grain [^rein] n. 纹理 L20graphic ['^rAfik] adj. 图解的 L6grasp [^rAsp] vt. 抓住 L8grid[^rid] n. 格子, 网格 L16grind[^raind] v. 磨, 磨削, 研磨 L3grinding ['^raindiN] n. 磨光,磨削 L3,20 grinding machine 磨床 L5gripper[^ripE] n. 抓爪, 夹具 L9groove[^ru:v] n. 凹槽 L12guide bush 导套 L5guide pillar 导柱 L5guide pillars and bushes 导柱和导套 L11Hhandset['hAndset] n. 电话听筒 L4hardness['ha:dnis] n.硬度 L1,2hardware ['ha:dwZE] n. 硬件 L6headstock['hedstCk] n.床头箱, 主轴箱 L5hexagonal[hek'sA^Enl] a. 六角形的, 六角的 L11 hindrance['hindrEns] n.障碍, 障碍物 L11hob[hCb] n. 滚刀, 冲头 L4hollow-ware 空心件 L21horizontal[hCri'zCntl] a. 水平的 L16hose[hEuz] n. 软管, 水管 L13hyperbolic [haipE'bClik] adj.双曲线的 L7Ii.e. (id est) [拉] 也就是 L12identical[ai'dentikl] a同样的 L16identify [ai'dentifai] v. 确定, 识别 L7idle ['aidl] adj.空闲的 L8immediately[i'mi:djEtli] adv. 正好, 恰好 L12impact['impAkt] n.冲击 L1impart [im'pa:t] v.给予 L11,17implement ['implimEnt] vt 实现 L6impossibility[impCsE'biliti] n.不可能 L21impression[im'preFEn] n. 型腔 L11in contact with 接触 L1in terms of 依据 L1inasmuch (as)[inEz'mQtF] conj.因为, 由于L3inch-to-metric conversions 英公制转换 L7 inclinable [in'klainEbl] adj. 可倾斜的 L20inclusion [in'kluFEn] n. 内含物 L19inconspicuous[inkEn'spikjuEs] a. 不显眼的 L14 incorporate [in'kC:pEreit] v 合并,混合L17 indentation[7inden'teiFEn ] n.压痕 L1indenter[in'dentE] n. 压头 L1independently[indi'peinEntli] a. 独自地, 独立地 L16 inevitably[in'evitEbli] ad. 不可避免地 L14 inexpensive[inik'spensiv]adj. 便宜的 L2inherently [in'hiErEntli] adv.固有的 L7injection mould 注塑模 L11injection[in'dVekFEn] n. 注射 L11in-line-of-draw 直接脱模 L14insert[in'sE:t] n. 嵌件 L16inserted die 嵌入式凹模 L19inspection[in'spekFEn] n.检查,监督 L9installation[instE'leiFEn] n. 安装 L10integration [inti'^reiFEn] n.集成 L6intelligent[in'telidVEnt]a. 智能的 L9intentinonally [in'tenFEnEli] adv 加强地，集中地 L17interface ['intEfeis] n.. 界面 L6internal[in'tE:nl] a. 内部的 L1,5interpolation [intEpE'leiFEn] n.插值法 L7 investment casting 熔模铸造 L4irregular [i'regjulE] adj. 不规则的，无规律 L17 irrespective of 不论, 不管 L11irrespective[iri'spektiv] a. 不顾的, 不考虑的 L11 issue ['isju] vt. 发布，发出 L6Jjoint line 结合线 L14Kkerosene['kerEsi:n] n.煤油 L10keyboard ['ki:bC:d ] n. 健盘 L6knock [nRk] v 敲，敲打 L17Llance [la:ns] v. 切缝 L19lathe[leiT] n. 车床 L4latitude ['lAtitju:d] n. 自由 L17lay out 布置 L13limitation[limi'teiFEn] n.限度,限制,局限(性) L3 local intelligence局部智能 L9locate [lEu'keit] vt. 定位 L18logic ['lCdVik] n. 逻辑 L7longitudinal['lCndVE'tju:dinl] a. 纵向的 L5 longitudinally['lCndVE'tju:dinl] a. 纵向的 L13 look upon 视作, 看待 L17lubrication[lju:bri'keiFEn ] n.润滑 L21Mmachine shop 车间 L2machine table 工作台 L8machining[mE'Fi:niN] n. 加工 L3made-to-measure 定做 L15maintenance['meintinEns] n.维护,维修 L7majority[mE'dVa:riti] n.多数 L21make use of 利用 L2male[meil] a. 阳的, 凸形的 L11malfunction['mAl'fQNFEn] n. 故障 L9mandrel['mAdtil] n.心轴 L22manifestation[mAnifEs'teiFEn] n. 表现, 显示 L9 massiveness ['mAsivnis ] 厚实，大块 L19measure['meVE] n. 大小, 度量 L1microcomputer 微型计算机 L9microns['maikrCn] n.微米 L10microprocessor 微处理器 L9mild steel 低碳钢 L17milling machine 铣床 L4mineral['minErEl] n.矿物, 矿产 L2minimise['minimaiz] v.把···减到最少, 最小化 L13minute['minit] a.微小的 L10mirror image 镜像 L16mirror['mirE] n. 镜子 L16MIT (Massachusetts Institute of Technology) 麻省理工学院 L7 moderate['mCdErit]adj. 适度的 L1,2modification [mRdifi'keiFEn ] n. 修改, 修正 L6modulus['mCdjulEs] n.系数 L1mold[mEuld] n. 模, 铸模, v. 制模, 造型 L3monitor ['mCnitE ] v. 监控 L6monograph['mCnE^ra:f] n. 专著 L4more often than not 常常 L20motivation[mEuti'veiFEn] n. 动机 L9mould split line 模具分型线 L12moulding['mEudiN] n. 注塑件 L5,11move away from 抛弃 L17multi-imprssion mould 多型腔模 L12Nnarrow['nArEu] a. 狭窄的 L12NC (numerical control ) 数控 L7nevertheless[7nevETE'les] conj.,adv.然而,不过 L11nonferrous['nCn'ferEs] adj.不含铁的, 非铁的 L2normally['nC:mli]adv.通常地 L22novice['nCvis] n. 新手, 初学者 L16nozzle['nCzl] n. 喷嘴, 注口 L12numerical [nju'merikl] n. 数字的 L6Oobjectionable [Eb'dVekFEbl] adj. 有异议的，讨厌的 L17observe[Eb'zE:v] vt. 观察 L2obviously ['CbviEsli] adv 明显地 L17off-line 脱机的 L6on-line 联机 L9operational [CpE'reiFEnl] adj.操作的, 运作的 L8opportunity[CpE'tju:niti] n. 时机, 机会 L13opposing[E'pEuziN] a.对立的, 对面的L12opposite['CpEzit] n. 反面 L1 a.对立的,对面的 L12 optimization [Rptimai'zeiFEn] n.最优化 L6orient ['C:riEnt] vt. 确定方向 L8orthodox ['C:WEdCks] adj. 正统的，正规的 L19overall['EuvErC:l] a.全面的,全部的 L8,13overbend v.过度弯曲 L20overcome[EuvE'kQm] vt.克服, 战胜 L10overlaping['EuvE'lApiN] n. 重叠 L4overriding[EuvE'raidiN] a. 主要的, 占优势的 L11 Ppack[pAk] v. 包装 L2package ['pAkidV] vt.包装 L7pallet ['pAlit] n.货盘 L8panel ['pAnl] n.面板 L7paraffin['pArEfin] n. 石蜡 L10parallel[pArElel] a.平行的 L5penetration[peni'treiFEn ] n.穿透 L1peripheral [pE'rifErEl] adj 外围的 L6periphery [pE'rifEri] n. 外围 L18permit[pE'mit] v. 许可, 允许 L16pessure casting 压力铸造 L4pillar['pilE] n. 柱子, 导柱 L5,17pin[pin] n. 销, 栓, 钉 L5,17pin-point gate 针点式浇口 L12piston ['pistEn] n.活塞 L1plan view 主视图 L16plasma['plAzmE] n. 等离子 L9plastic['plAstik] n. 塑料 L3platen['plAtEn] n. 压板 L12plotter[plCtE] n. 绘图机 L9plunge [plQndV] v翻孔 L18plunge[plQndV] v.投入 L2plunger ['plQndVE ] n. 柱塞 L19pocket-size 袖珍 L9portray[pC:'trei] v.描绘 L21pot[pCt] n.壶 L21pour[pC:] vt. 灌, 注 L22practicable['prAktikEb] a. 行得通的 L14 preferable['prefErEbl] a.更好的, 更可取的 L3 preliminary [pri'liminEri] adj 初步的，预备的 L19 press setter 装模工 L17press[pres] n.压,压床,冲床,压力机 L2,8prevent [pri'vent] v. 妨碍 L20primarily['praimErili] adv.主要地 L4procedure[prE'si:dVE] n.步骤, 方法, 程序 L2,16 productivity.[prEudQk'tiviti] n. 生产力 L9profile ['prEufail] n.轮廓 L10progressively[prE'^resiv] ad.渐进地 L15project[prE'dVekt] n.项目 L2project[prE'dVekt] v. 凸出 L11projection[prE'dVekFEn] n.突出部分 L21proper['prCpE] a. 本身的 L10property['prCpEti] n.特性 L1prototype ['prEutEtaip] n. 原形 L7proximity[prCk'simiti] n.接近 L9prudent['pru:dEnt] a. 谨慎的 L16punch [pQntF] v. 冲孔 L3punch shapper tool 刨模机 L17punch-cum-blanking die 凹凸模 L18punched tape 穿孔带 L3purchase ['pE:tFEs] vt. 买，购买 L6push back pin 回程杆 L5pyrometer[pai'nCmitE] n. 高温计 L2Qquality['kwaliti] n. 质量 L1,3quandrant['kwCdrEnt] n. 象限 L9quantity ['kwCntiti] n. 量，数量 L17quench[kwentF] vt. 淬火 L2Rradial['reidiEl] adv.放射状的 L22ram [rAm] n 撞锤. L17rapid['rApid]adj. 迅速的 L2rapidly['rApidli]adv. 迅速地 L1raster['rAstE] n. 光栅 L9raw [rC:] adj. 未加工的 L6raw material 原材料 L3ream [ri:m] v 铰大 L17reaming[ri:miN] n. 扩孔, 铰孔 L8recall[ri'kC:l] vt. 记起, 想起 L13recede [ri'si:d] v. 收回, 后退 L20recess [ri'ses] n. 凹槽,凹座,凹进处 L4,18redundancy[ri'dQndEnsi] n. 过多 L9re-entrant 凹入的 L12refer[ri'fE:] v. 指, 涉及, 谈及 L1,12reference['refErEns] n.参照,参考 L21refresh display 刷新显示 L9register ring 定位环 L11register['redVstE] v. 记录, 显示, 记数 L2regrind[ri:'^aind](reground[ri:'gru:nd]) vt. 再磨研 L12 relative['relEtiv] a. 相当的, 比较的 L12relay ['ri:lei] n. 继电器 L7release[ri'li:s] vt. 释放 L1relegate['relE7geit] vt. 把··降低到 L9reliability [rilaiE'biliti] n. 可靠性 L7relief valves 安全阀 L22relief[ri'li:f] n.解除 L22relieve[ri'li:v ]vt.减轻, 解除 L2remainder[ri'meindE] n. 剩余物, 其余部分 L4 removal[ri'mu:vl] n. 取出 L14remove[ri'mu:v] v. 切除, 切削 L4reposition [ripE'ziFEn] n.重新安排 L17 represent[7repri'zentE] v 代表,象征 L11 reputable['repjutEbl] a. 有名的, 受尊敬的 L15 reservoir['rezEvwa: ] n.容器, 储存器 L22 resident['rezidEnt] a. 驻存的 L9resist[ri'zist] vt.抵抗 L1resistance[ri'zistEns] n.阻力, 抵抗 L1 resolution[7rezE'lu:FEn] n. 分辨率 L9 respective[ri'spektiv] a.分别的,各自的 L11 respond[ris'pCnd] v.响应, 作出反应 L9 responsibility[rispCnsE'biliti] n.责任 L13 restrain[ris'trein]v.抑制 L21restrict [ris'trikt] vt 限制，限定 L18 restriction[ris'trikFEn] n. 限制 L12retain[ri'tein] vt.保持, 保留 L2,12 retaining plate 顶出固定板 L16reveal [ri'vil] vt.显示，展现 L17reversal [ri'vEsl] n. 反向 L1,20right-angled 成直角的 L20rigidity[ri'dViditi] n. 刚度 L1rod[rCd] n. 杆, 棒 L1,5rotate['rEuteit] vt.(使)旋转 L5rough machining 粗加工 L5rough[rQf] a. 粗略的 L5,21routine [ru:'ti:n] n. 程序 L7rubber['rQbE] n.橡胶 L3,22runner and gate systems 流道和浇口系统 L11Ssand casting 砂型铸造 L3satisfactorily[7sAtis'fAktrili] adv. 满意地 L1 saw[aC:] n. 锯子 L4scale[skeil]n. 硬壳 L2score[skC:] v. 刻划 L14scrap[skrAp] n.废料, 边角料, 切屑 L2,3 screwcutting 切螺纹 L4seal[si:l] vt.密封 L22secondary storage L9section cutting plane 剖切面 L16secure[si'kjuE] v.固定 L22secure[si'kjuE] vt.紧固,夹紧,固定 L5,22segment['se^mEnt] v. 分割 L10sensitive['sensitiv]a.敏感的 L1,7sequence ['si:kwEns] n. 次序 L6sequential[si'kwenFEl] a.相继的 L16seriously['siEriEsli] adv.严重地 L1servomechanism ['sE:vE'mekEnizm] n.伺服机构 L7 Servomechanism Laboratoies 伺服机构实验室 L7 servomotor ['sE:vEmEutE] n.伺服马达 L8setter ['setE] n 安装者 L17set-up 机构 L20sever ['sevE] v 切断 L17severity [si'veriti] n. 严重 L20shaded[FAdid] adj.阴影的 L21shank [FANk] n. 柄. L17shear[FiE]n.剪,切 L1shot[FCt] n. 注射 L12shrink[FriNk] vi. 收缩 L11side sectional view 侧视图 L16signal ['si^nl] n.信号 L8similarity[simi'lAriti] n.类似 L15simplicity[sim'plisiti] n. 简单 L12single-point cutting tool 单刃刀具 L5situate['sitjueit] vt. 使位于, 使处于 L11slide [slaid] vi. 滑动, 滑落 L20slideway['slaidwei] n. 导轨 L5slot[slCt] n. 槽 L4slug[slQ^] n. 嵌条 L12soak[sEuk] v. 浸, 泡, 均热 L2software ['sCftwZE] n. 软件 L6solid['sClid] n.立体, 固体 L9solidify[sE'lidifai] vt.vi. (使)凝固, (使)固化 L13 solution[sE'lu:FEn] n.溶液 L2sophisiticated [sE'fistikeitid] adj.尖端的,完善的 L8 sound[saund] a. 结实的, 坚固的) L1spark erosion 火花蚀刻 L10spindle['spindl] n. 主轴 L5,8spline[splain] n.花键 L4split[split] n. 侧向分型, 分型 L12,14spool[spu:l] n. 线轴 L14springback n.反弹 L20spring-loaded 装弹簧的 L18sprue bush 主流道衬套 L11sprue puller 浇道拉杆 L12square[skwZE] v. 使成方形 L4stage [steidV] n. 阶段 L16,19standardisation[7stAndEdai'zeiFEn] n. 标准化 L15 startling['sta:tliN] a. 令人吃惊的 L10steadily['stedEli ] adv. 稳定地 L21step-by-step 逐步 L8stickiness['stikinis] n.粘性 L22stiffness['stifnis] n. 刚度 L1stock[stCk] n.毛坯, 坯料 L3storage tube display 储存管显示 L9storage['stC:ridV] n. 储存器 L9straightforward[streit'fC:wEd]a.直接的 L10strain[strein] n.应变 L1strength[streNW] n.强度 L1stress[stres] n.压力,应力 L1stress-strain应力--应变 L6stretch[stretF] v.伸展 L1,21strike [straik] vt. 冲击 L20stringent['strindVEnt ] a.严厉的 L22stripper[stripE] n. 推板 L15stroke[strouk] n. 冲程, 行程 L12structrural build-up 结构上形成的 L11sub-base 垫板 L19subject['sQbdVikt] vt.使受到 L21submerge[sEb'mE:dV] v.淹没 L22subsequent ['sQbsikwent] adj. 后来的 L20 subsequently ['sQbsikwentli] adv. 后来, 随后 L5 substantial[sEb'stAnFEl] a. 实质的 L10substitute ['sQbstitju:t] vt. 代替,.替换 L7 subtract[sEb'trAkt] v.减, 减去 L15suitable['su:tEbl] a. 合适的, 适当的 L5suitably['su:tEbli] ad.合适地 L15sunk[sQNk](sink的过去分词) v. 下沉, 下陷 L11 superior[sE'piEriE] adj.上好的 L22susceptible[sE'septEbl] adj.易受影响的 L7sweep away 扫过 L17symmetrical[si'metrikl] a. 对称的 L14 synchronize ['siNkrEnaiz] v.同步,同时发生L8Ttactile['tAktail] a. 触觉的, 有触觉的 L9 tailstock['teilstCk] n.尾架 L5tapered['teipEd] a. 锥形的 L12tapping['tApiN] n. 攻丝 L8technique[tek'ni:k] n. 技术 L16tempering['tempErN] n.回火 L2tendency['tendEnsi] n. 趋向, 倾向 L13tensile['tensail] a.拉力的, 可拉伸的 L2 拉紧的, 张紧的 L1 tension ['tenFEn] n.拉紧,张紧 L1terminal ['tE:mEnl ] n. 终端机 L6terminology[tE:mi'nClEdVi ] n. 术语, 用辞 L11theoretically [Wi:E'retikli ] adv.理论地 L21thereby['TZEbai] ad. 因此, 从而 L15thermoplastic['WE:mEu'plAstik] a. 热塑性的, n. 热塑性塑料 L3thermoset['WE:mEset] n.热固性 L12thoroughly['WQrEuli] adv.十分地, 彻底地 L2thread pitch 螺距 L5thread[Wred] n. 螺纹 L5thrown up 推上 L17tilt [tilt] n. 倾斜, 翘起 L20tolerance ['tClErEns] n..公差 L17tong[tCN] n. 火钳 L2tonnage['tQnidV] n.吨位, 总吨数 L3tool point 刀锋 L3tool room 工具车间 L10toolholder['tu:lhEuldE] n.刀夹,工具柄 L5toolmaker ['tu:l'meikE] n 模具制造者 L17toolpost grinder 工具磨床 L4toolpost['tu:l'pEust] n. 刀架 L4torsional ['tC:FEnl] a扭转的 . L1toughness['tCfnis] n. 韧性 L2trace [treis] vt.追踪 L7tracer-controlled milling machine 仿形铣床 L4transverse[trAns'vE:s] a. 横向的 L5tray [trei] n. 盘，盘子，蝶 L19treatment['tri:tmEnt] n.处理 L2tremendous[tri'mendEs] a. 惊人的, 巨大的 L9trend [trend] n.趋势 L7trigger stop 始用挡料销 L17tungsten['tQNstEn] n.钨 L10turning['tE:niN] n.车削 L4,5twist[twist ] v.扭曲，扭转 L1two-plate mould 双板式注射模 L12Uultimately['Qltimitli] adv终于. L6undercut moulding 侧向分型模 L14undercut['QndEkQt] n. 侧向分型 L14undercut['QndEkQt] n.底切 L12underfeed['QndE'fi:d] a, 底部进料的 L15undergo[QndE'^Eu] vt.经受 L1underside['QndEsaid] n 下面,下侧 L11undue[Qn'dju:] a.不适当的, 过度的 L4,10uniform['ju:nifC:m] a.统一的, 一致的 L12utilize ['ju:tilaiz] v 利用 L17Utopian[ju'tEupiEn] adj.乌托邦的, 理想化的 L21Vvalve[vAlv] n.阀 L22vaporize['veipEraiz] vt.vi. 汽化, (使)蒸发 L10 variation [vZEri'eiFEn] n. 变化 L20various ['vZEriEs] a.不同的,各种的 L1,20vector feedrate computation 向量进刀速率计算 L7 vee [vi:] n. v字形 L20velocity[vi'lCsiti] n.速度 L1versatile['vEsEtail] a.多才多艺的,万用的 L5,8 vertical['vE:tikl] a. 垂直的 L16via [vaiE] prep.经,通过 L8vicinity[vE'siniti] n.附近 L13viewpoint['vju:pCint] n. 观点 L4Wwander['wCndE] v. 偏离方向 L13warp[wC:p] v. 翘曲 L2washer ['wCFE] n. 垫圈 L18wear [wZE] v.磨损 L7well line 结合线 L13whereupon [hwZErE'pCn] adv. 于是 L19winding ['waindiN] n. 绕, 卷 L8with respect to 相对于 L1,5withstand[wiT'stAnd] vt.经受,经得起 L1work[wE:k] n. 工件 L4workstage 工序 L19wrinkle['riNkl] n.皱纹vt.使皱 L21Yyield[ji:ld] v. 生产 L9Zzoom[zu:] n. 图象电子放大 L9GLOSSARY。
塑胶原料类 英语词汇
塑胶原料类英语词汇.txt如果不懂就说出来，如果懂了，就笑笑别说出来。
贪婪是最真实的贫穷，满足是最真实的财富。
幽默就是一个人想哭的时候还有笑的兴致。
塑胶原料类专业词汇ABS 丙烯腈-丁二烯-苯乙烯共聚物ABS alloys 丙烯腈-丁二烯-苯乙烯共聚物合金Acrylic 丙烯酸/玻璃胶Alkyd 醇酸树脂Alloys 合金Amino 氨基树脂ASA 丙烯腈-苯乙烯丙烯酸脂元共聚物ASA alloys 丙烯腈-苯乙烯丙烯酸脂元共聚物合金BDS 散装模塑料BR 丁二烯橡胶CA 醋酸纤维素CAB 醋酸丁酸纤维素CAP 醋酸丙酸纤维素casein 酪素CF 甲酚树脂composite material 复合材料CPE 氯化聚乙烯CPVC 氯化聚氯乙烯cross linking agents 交联剂curing agents 塑化剂dially phthalate 苯二甲酸二烯丙酯diaminodiphenyl methane MDA 二氨基二苯基甲烷diphenylmethane diisocyanteMDI 二苯基甲烷二异dough making compound 团体成型料engineering plastics 工程塑胶EPDM 乙烯-丙烯，二烯共聚物epoxy resin 环氧树脂EPS 泡沫聚苯烯板材ethyl cellulose 乙基纤维素EVA 乙烯-醋酸乙烯共聚物expanded polystyrene 泡沫聚苯乙烯Extrusion tubes 挤出管材FEP 氟化乙丙烯fiber reinforcement 纤维强化热固性/纤维强化复合材料fibre 纤维forming agent 发泡剂glass mat thermoplastics 玻璃毯热塑性塑料GPPS 硬胶（通用级聚苯乙烯）H/POM-H 聚氧化甲烯high density polyethylene 高密度聚乙烯HIPS 高耐冲击聚苯乙烯impact modifiers 抗冲击性改进剂LCP 液晶高分子LDPE 低密度聚乙烯LDPE 低密度聚乙烯LLDPE 线型低密度聚乙烯lonomer 离子键树脂MBS 甲基丙烯酸甲酯-丁二烯-苯乙烯共聚物MDPE 中密度聚乙烯melmine resin 三聚氰胺酚醛树脂nitrocellulose 硝酸纤维素Nylons 尼龙PA 耐龙PA,Nylon 聚酰胺，尼龙PAEK 聚芳基醚酮PAP 聚苯烯酸PBT 聚对苯二甲酸丁二醇酯PC 聚碳酸酯PC /PBT alloys 聚碳酸酯/聚苯并噻唑合金PE 聚乙烯PEI 聚醚酰亚胺PE-others 其他聚乙烯PES 聚醚砜PET 聚乙二醇对苯二甲酸酯PETG 二醇类改性聚对苯二甲酸乙二醇酯phenolic resin 酚醛树脂PI 聚酰亚胺plastic 塑胶PMMA 聚甲基丙烯酸甲酯polymethane polyhenyl socyanate 多次甲基多苯基异氰酸酯polyolifens 聚烯烃polyster chip 聚酯切片polyster elastomer 聚酯弹性体polyster moulding compound 聚乙烯模塑料POM(ACETAL) 共聚甲醛PP/EPOM 聚丙烯/乙烯-丙烯二烯共聚物PPE 聚苯醚PP--polypropene 聚丙烯PPS 聚苯硫醚processing aids 加工助剂PS 聚苯乙烯PSU 聚砜PTFE 聚四氟乙烯PU 聚氨（基甲酸）酯PU-based synthetic rubber 聚氨酯基合成来胶purge compounds 清基料PVC 聚氯乙烯PVC stablizer 聚氯乙烯稳定剂reinforced resins 增强树脂reinforcement 分散性强化复合材料reinforcements 加强剂resins 树脂rheological enhancer 流变改性剂rubber 橡胶SAN 苯乙烯-丙烯腈共聚物SB 苯乙烯-丁二烯共聚物SB copolymers 一树脂丁苯共聚物SBS 苯乙烯-丁二烯-苯乙烯嵌段共聚物sheet moulding compound 板材膜塑料silane crosslinked pipe material 硅烷交联管料thermoelastic rubber&compounds 热塑性橡胶TPE 三苯基乙烷TPU 增韧聚氢脂UF 脲甲酚树脂UP 不饱和树脂UV stabilizer 紫外线稳定剂VC 副聚氯乙烯Wax- PE blend 聚乙烯。
日用百货小商品一类的搜索词汇
日用百货小商品一类的搜索词汇
塑料制品：收纳箱、凳子、椅子、刷子、衣架、水桶、口杯、脸盆、密封罐、垃圾桶、真空压缩袋、花盆、喷雾器、皂盒、衣叉等。
清洁用品：胶棉拖、平板拖、扫把簸箕套装、垃圾桶、手套、百洁布、清洁球、海绵擦、玻璃擦、马桶垫、马桶刷等。
厨房用品：炒锅、炊具、刀剪、洗菜篮、打蛋器、切菜器、碗碟架、挂篮、油壶、调味瓶、锅铲、漏勺、开瓶器、磨刀器、料理器、厨房小工具等。
竹木制品：砧板、筷子、刀架、擀面棍、牙签、竹签、果盘、竹质工艺品、餐垫、杯垫、勺等。
玻璃器皿：玻璃餐具、储物罐、玻璃水杯、酒杯、玻璃花盆、花瓶、烟灰缸、烛台、水壶、水具、密封罐、保鲜盒等。
日用陶瓷：餐具、砂锅、马克杯、壶、缸、坛、盆、罐、盘、碟、碗等。
杯壶：保温杯、壶、瓶、运动水壶、玻璃杯、创意杯、紫砂杯、汽车杯、随手杯等。
茶具：茶具套装、礼品餐饮套装、茶壶、茶碗、茶盘、茶杯、盖碗、铁壶、紫砂等。
厨具：叉、勺、筷、碗、碟、盘、保温饭盒、保鲜碗、壶、瓶、刨子、削皮器、蒸锅、厨房置物架、烧烤炉等。
一次性用品：保鲜膜、垃圾袋、水晶杯、碗、吸管、棉签、台布、快餐盒、打包盒、鞋套等。
浴室用品：沐浴球、吸盘置物架、防滑垫、马桶垫、浴帽、吸水毛巾、澡巾、化妆包等。
小家居：衣帽钩、鞋架、换鞋凳、置物架、桌子、躺椅、遮阳伞、布衣柜等。
家居用品：地毯、餐桌用品、水晶板、床上用品、抱枕、毛巾、梳子、镜子、针线盒、饰品、箱包、雨具、户外园艺、灯饰、挂钟、塑料玩具、婚庆用品、工艺品摆件等。
日化用品：清新剂、清洁剂、洗衣液、牙刷、牙膏、蚊香、鞋油、沐浴露、洗发水等。
小电器：厨房电器、家居电器、个人护理电器、养生电器、电取暖器、排插等。
注塑英文词汇汇总
英文中文英文中文Layout布置图机械设计及周边其它用语Conveyer流水线物料板assembly drawing装配图Rivet table拉钉机auto tool change cycle自动换刀时间周期Rivet gun拉钉枪beam横梁Screw driver起子bottoming底靠Electric screw driver电动起子buckling纵弯曲Pneumatic screw driver气动起子chamfering去角斜切fit together组装在一起channel凹槽fasten锁紧(螺丝)chattering颤动fixture ，jig夹具(治具)check point查核点barcode条形码chip切屑barcode scanner条形码扫描仪chip conveyor排屑输送机fuse together熔合coefficient of friction摩擦系数fuse machine热熔机compact小型的repair修理，纠正，返修cooling pipe冷却管thumb screw大头螺丝coupon试样胚lbs.inch镑、英寸distortion扭曲变形EMI gasket导电条draft taper拔模锥度front plate前板fit tolerance配合公差rear plate后板flexible rigidity弯曲刚性chassis |'∫æsi|基座gas vent气孔，排气管bezel panel面板heater cooler加热器冷却装置power button电源按键hook cavity钩穴reset button重置键lug凸缘Hi-pot test of SPS高源高压测试maintenance维修保固Voltage switch of SPS电源电压接柆键metallurgy冶金学sheet metal parts冲件notch effect切口效果plastic parts塑料件out of roughness真圆度sub-line支线performance动作性能uncoiler and straightener开卷矫直机pit坑robot机械手plane strain倒角应力hydraulic machine油压机plug mill蕊棒轧管机lathe车床repeated load重复载荷刨床riveted joint铆钉接合miller铣床sand paper砂纸grinder磨床shift偏移driller钻床shrink fit热压配合linear cutting线切割shrinkage hole缩孔electrical sparkle电火花sinking凹陷welder电焊机sketch草图staker=reviting machine铆合机spalling剥落compound die合模，复式压膜straightness直度die locker锁模器submarine深陷式pressure plate，plate压板，夹板surface roughness表面粗度bolt螺栓tapping攻螺丝automatic screwdriver电动启子thermocouple热电耦thickness gauge厚薄规torsion load扭转载荷gauge量规toughness韧性power wire电源线tracing描图buzzer蜂鸣器under cut凹割screwdriver holder起子插座abnormal glow不规则辉光放电pedal踩踏板abrasive砂轮stopper阻挡器access通路flow board流水板accretion炉瘤hydraulic handjack油压板车accurate die casting精密压铸head of screwdriver起子头acid converter酸性转炉chain链条，链条槽acid lining cupola酸性熔铁炉production line流水线，生产线acid open-hearth furnance ，酸性平炉magnetizer加磁器activator活化剂die repair模修acetylene乙炔die worker模工adjustable spanner活动扳手equipment设备aerator松砂机to start a press开机after service售后服务stop/switch off a press关机age hardening时效硬化board基板ageing老化处理feeder送料机air hardening气体硬化sliding rack滑料架air patenting空气韧化die change换模air permeability test透气性试验to fix a die装模air set mold常温自硬铸模to take apart a die拆模all core molding集合式铸模to repair a die修模alloy tool steel合金工具钢to pull and stretch拉深allround die holder通用模型to put material in place, to落料aluminium alloy铝合金钢to impose lines，groove压线amendment修正to compress, compressing压缩ampere电流安培character die字模anchor pin锚梢parameters参数angle cutter角铣刀rotating speed, revolution转速angle welding角焊steel plate钢板angular pin角梢，倾斜梢to switch over to, switch--切换anode effect阳极效应engineering, project工程瓶颈straightness直线度stage die工程模flatness平面度automation自动化roundness圆度add lubricating oil加润滑油Cylindnicity圆柱度shut die架模line profile线轮廓shut height闭合高度surface profile面轮廓shut height of a die架模高度parallelism平行度analog-mode device类模器perpendicularity垂直度die lifter举模器angularity倾斜度argon welding氩焊symmetry对称度vocabulary for stamping冲压常词汇coaxiality同轴度punch press, dieing out冲床concentricity同心度uncoiler & strainghtener整平机true position位置度rack, shelf, stack料架runout圆跳动cylinder汽缸套，油缸，气缸total run-ou全跳动taker取料机学理实验与试验用语conveyer belt输送带austenitic steel沃斯田铁钢transmission rack输送架brinell hardness布耐内尔硬度top stop上死点brinell hardness test布氏硬度试验bottom stop下死点charpy impact test夏比冲击试验one stroke一行程conical cup test圆锥杯突试验inch寸动cup flow test杯模式流动度试验to continue, cont.连动dart drop impact test落锤冲击试验to grip(material)吸料Elmendorf test埃罗门多撕裂强度试验location lump, locating定位块environmental stress cracking环境应力龟裂试验reset复位ericessen test埃留伸薄板拉伸试验smoothly顺利falling ball impact test落球冲击试验filing锉刀修润，锉削加工fatigue test疲劳试验filings铁削gantt chart甘特图to draw holes抽孔heat cycle test热循环试验reverse angle = chamfer倒角histogram柱状图to take apart a die卸下模具hot bend test热弯试验to load a die装上模具izod impact test埃左德冲击试验to tight a bolt拧紧螺栓loop tenacity环结强度to looser a bolt拧松螺栓martens heat distortion马顿斯耐热试验to move away a die plate移走模板mullen bursting strength tester密廉式破裂强度试验机easily damaged parts易损件nol ring test诺尔环试验standard parts标准件normal distribution常态分配breaking.(be)broken,(be)c断裂ozone resistance test抗臭氧试验to lubricate润滑pareto diagram柏拉图common vocabulary for模具工程常用词汇peeling test剥离试验die模具pinhole test针孔试验机cutting die, blanking die冲裁模rattler test磨耗试验progressive die, follow (-连续模rockweel hardness test洛氏硬度试验compound die，gang dies复合模rockweel hardness洛氏威尔硬度punched hole，pierce冲孔rolinx process罗林克斯射出压缩成形panel board，embedded镶块rossi-peakes flow test罗西皮克斯流动试验side cut，side scrap切边sampling inspection抽样检查to bending折弯scratch hardness抗刮硬度to pull, to stretch拉伸shore hardness萧氏硬度Line streching, line pulling线拉伸spiral flow test螺旋流动试验engraving, to engrave刻印surface abrasion test表面磨耗试验upsiding down edges翻边taber abraser泰伯磨耗试验机staking铆固tensile impact test拉伸冲击试验designing, to design设计tensile strength抗拉强度design modification设计变化tension test张力试验folded block折弯块thermal shock test冷热剧变试验sliding block滑块torsion test扭曲试验die plate, front board模板ubbelohde viscometer乌别洛德黏度计padding block垫块vicat indentation test维卡针压陷试验stepping bar垫条Vickers hardness test维氏硬度试验lower die base，die set下模座warpage test翘曲试验upper supporting blank上承板weatherometer人工老化试验机upper padding plate上垫板weissenberg effect威森伯格回转效应spare dies模具备品砂轮用语plate电镀Al2O3氧化铝mold模具，模型bond结合material for engineering工程试模材料borazon氧化硼立方晶not included in physical不列入盘点diamond钻石tox machine自铆机dresser砂轮整修机wire EDM线割endless grinding belt循环式研磨带EDM放电机finishing allowance加工留量，加工余量coil stock，roll material卷料grain磨粒sheet stock片料grinding disc研磨盘tolerance工差jamp up孔眼堵塞score成绩mesh网筛目cam block凸轮块，滑块resinoid grinding wheel半树脂型砂轮pilot试产，试验vitrified陶瓷的trim修剪，整理，装饰wheel旋转pierce剪内边模具常用之工作机械drag form压锻差3D coordinate measurement三次元量床pocket for the punch head挂钩槽boring machine搪孔机slug hole废料孔cnc milling machine CNC铣床feature die公母模 contouring machine轮廓锯床expansion dwg展开图copy grinding machine仿形磨床shim(wedge)楔子copy lathe仿形车床torch-flame cut火焰切割copy milling machine仿形铣床round pierce punch=die圆冲子copy shaping machine仿形刨床shape punch=die insert异形子cylindrical grinding machine外圆磨床under cut=scrap chopper清角die spotting machine合模机cover plate盖板drilling machine钻孔机male die公模(凸模)engraving machine雕刻机female die母模(凹模)engraving E.D.M.雕模放置加工机groove punch压线冲子form grinding machine成形磨床air-cushion eject-rod气垫顶杆graphite machine石墨加工机spring-box eject-plate弹簧箱顶板horizontal boring machine卧式搪孔机bushing block衬套horizontal machine center卧式加工制造中心club car高尔夫球车internal cylindrical machine内圆磨床capability能力jig boring machine冶具搪孔机factor系数jig grinding machine冶具磨床phosphate皮膜化成lap machine研磨机viscosity涂料粘度machine center加工制造中心alkalidipping，degrease脱脂multi model miller靠磨铣床main manifold主集流脉NC drilling machine NC钻床bezel斜视规NC grinding machine NC磨床dejecting顶固模NC lathe NC车床demagnetization去磁;消磁NC programming system NC程序制作系统high-speed transmission高速传递 planer龙门刨床heat dissipation热传profile grinding machine仿形磨床，投影磨床rack上料projection grinder光学曲线磨床，投影磨rinse水洗radial drilling machine旋臂钻床alkaline etch龄咬surface grinder平面磨床desmut剥黑膜try machine试模机D.I. rinse纯水次turret lathe转塔车床Chromate铬酸处理universal tool grinding万能工具磨床Anodize阳性处理vertical machine center立式加工制造中心seal封孔wire E.D.M.线割放电加工机stamping冲压检验量测工具用语molding成型autocollimator自动准直机coordinate坐标bench comparator比长仪dismantle the die折模block gauge块规auxiliary fuction辅助功能bore check精密小测定器poly-line多义线calibration校准heater band加热片caliper gauge内量卡规thermocouple热电偶check gauge校对规sand blasting喷沙clearance gauge间隙规grit砂砾clinoretee测斜仪derusting machine除锈机comparator比测仪degate打浇口cylinder square圆筒直尺dryer烘干机depth gauge测深规response=reaction=interac感应dial indicator针盘指示表induction light感应光dial snap gauge千分表卡规ram连杆digital micrometer数位式测微计edge finder巡边器feeler gauge测隙规concave凸gauge plate量规定位板convex凹height gauge测高规short射料不足inside calipers内卡钳nick缺口 inside micrometer内分厘卡speck瑕疪interferometer干涉仪shine亮班leveling block平台splay银纹limit gauge限规gas mark焦痕micrometer测微计delamination起鳞mil千分之一吋cold slug冷块monometer压力计blush导色morse taper gauge莫氏锥度量规gouge沟槽;凿槽nonius游标卡尺satin texture段面咬花optical flat光学平晶witness line证示线optical parallel光学平行patent专利passimeter内径仪grit沙砾position scale位置刻度granule=peuet=grain细粒profile projector轮廓光学投影仪grit maker抽粒机protractor分角器cushion缓冲radius半径magnalium镁铝合金ring gauge环规magnesium镁金sine bar正弦量规metal plate钣金snap gauge卡模mill锉square master直角尺plane刨stylus触针grind磨telescopic gauge伸缩性量规drill铝working gauge工作量规boring镗模具钢材blinster气泡bearing alloy轴承合金fillet镶;嵌边bonderized steel sheet邦德防蚀钢板through-hole form通孔形式carbon tool steel碳素工具钢voller pin formality滚针形式clad sheet被覆板cam driver铡楔clod work die steel冷锻模用钢shank摸柄emery金钢砂augular offset角度偏差ferrostatic pressure钢铁水静压力velocity速度forging die steel锻造模用钢production tempo生产进度现状galvanized steel sheet镀锌铁板torque扭矩hard alloy steel超硬合金钢spline=the multiple keys花键high speed tool steel高速度工具钢annealing退火hot work die steel热锻模用钢carbonization碳化low alloy tool steel特殊工具钢alloy合金low manganese casting steel低锰铸钢tungsten high speed steel钨高速的marging steel马式体高强度热处理钢moly high speed steel钼高速的martrix alloy马特里斯合金organic solvent有机溶剂meehanite cast iron米汉纳铸钢liaison联络单meehanite metal米汉纳铁volatile挥发性merchant iron市售钢材resistance电阻molybdenum high speed steel钼系高速钢ion离子molybdenum steel钼钢titrator滴定仪nickel chromium steel镍铬钢beacon警示灯prehardened steel顶硬钢coolant冷却液silicon steel sheet硅钢板crusher破碎机stainless steel不锈钢模具工程类tin plated steel sheet镀锡铁板plain die简易模tough pitch copper ，tough韧铜pierce die冲孔模troostite吐粒散铁forming die成型模tungsten steel钨钢shearing die剪边模vinyl tapped steel sheet塑料覆面钢板riveting die铆合模表面处理关连用语forming成型(抽凸,冲凸)anodizing阳极氧化处理emboss凸点atomloy treatment阿扥木洛伊表面dome凸圆austempering奥氏体等温淬火semi-shearing半剪austenite奥斯田体/奥氏体stamp mark冲记号bainite贝氏体deburr or coin压毛边banded structure条纹状组织punch riveting冲压铆合barrel滚筒(加工)side stretch侧冲压平barrel plating滚镀reel stretch卷圆压平barrel tumbling滚筒打光stamp letter冲字(料号)blackening染黑法shearing剪断blue shortness青熟脆性tick-mark nearside正面压印bonderizing磷酸盐皮膜处理tick-mark farside反面压印box annealing箱型退火冲压名称类box carburizing封箱渗碳extension dwg展开图bright electroplating辉面电镀procedure dwg工程图bright heat treatment光辉热处理die structure dwg模具结构图bypass heat treatment旁路热处理material材质carbide炭化物material thickness料片厚度carburized case depth浸碳硬化深层factor系数carburizing渗碳upward向上cementite炭化铁downward向下chemical plating化学电镀press specification冲床规格chemical vapor deposition化学蒸镀die height range适用模高coarsening结晶粒粗大化die height闭模高度coating涂布被覆weight重量cold shortness低温脆性total wt.总重量comemtite渗碳体punch wt.上模重量controlled atmosphere大气热处理五金零件类corner effect锐角效应inner guiding post内导柱creeping discharge蠕缓放电inner hexagon screw内六角螺钉decarburization脱碳处理coil spring弹簧decarburizing脱碳退火lifter pin，lifting pin顶料销depth of hardening硬化深层eq-height sleeves=spool等高套筒diffusion扩散pin销diffusion annealing扩散退火wire spring圆线弹簧electrolytic hardening电解淬火outer guiding post外导柱embossing浮花压制加工，压花加stop screw，set screw止付螺丝，固定螺丝raising(embossing)压花起伏成形located pin，stop pin，定位销etching表面蚀刻outer bush外导套ferrite纯铁体，肥粒铁模板类first stage annealing第一段退火top plate上托板（顶板）flame hardening火焰硬化top block上垫脚flame treatment火焰处理punch set，upper die base上模座full annealing完全退火punch holder上夹板gaseous cyaniding气体氧化法stripper pad脱料背板 globular cementite球状炭化铁up stripper上脱料板grain size结晶粒度upper plate上模板granolite treatment磷酸溶液热处理lower plate下模板graphitizing石墨退火die pad下垫板 hardenability硬化性die holder下夹板hardenability curve硬化性曲线bottom block下垫脚hardening硬化stripping plate内外打(脱料板)heat treatment热处理outer stripper外脱料板hot bath quenching热浴淬火inner stripper内脱料板hot dipping热浸镀lower stripper下脱料板induction hardening高周波硬化零件类ion carbonitriding离子渗碳氮化punch冲头ion carburizing离子渗碳处理deburring punch压毛边冲子ion plating离子电镀stamped punch字模冲子isothermal annealing等温退火special shape punch异形冲子liquid honing液体喷砂法roller滚轴low temperature annealing低温退火supporting block for定位支承块malleablizing可锻化退火air cushion plate气垫板martempering麻回火处理trimming punch切边冲子martensite马氏体/硬化铁炭stiffening rib punch =加强筋冲子metallikon金属喷镀法ribbon punch压筋冲子metallizing真空涂膜reel-stretch punch卷圆压平冲子nitriding氮化处理guide plate导板，定位板nitrocarburizing软氮化sliding dowel block滑块固定块normalizing正常化active plate活动板oil quenching油淬化lower sliding plate下滑块板overageing过老化upper holder block上压块overheating过热upper mid plate上中间板pearlite针尖组织spring box弹簧箱phosphating磷酸盐化（金属表面处spring-box eject-rod弹簧箱顶杆physical vapor deposition物理蒸镀guide pad导料块plasma nitriding离子氮化塑件&模具相关英文pre-annealing预备退火compre sion molding压缩成型precipitation析出flash mold溢流式模具precipitation hardening析出硬化plsitive mold挤压式模具press quenching加压硬化split mold分割式模具process annealing制程退火cavity型控母模quench ageing淬火老化core模心公模quench hardening ，淬火taper锥拔quenching crack淬火裂痕leather cloak仿皮革quenching distortion淬火变形shiver饰纹quenching stress淬火应力flow mark流痕 reconditioning再调质welding mark溶合痕recrystallization再结晶post screw insert螺纹套筒埋值red shortness红热脆性self tapping screw自攻螺丝residual stress残留应力striper plate脱料板retained austenite残留奥piston活塞rust prevention防蚀chip细碎物salt bath quenching盐浴淬火handle mold手持式模具sand blast喷砂处理移转成型用模具seasoning时效处理encapsulation molding低压封装成型second stage annealing第二段退火射出成型用模具secular distortion经年变形two plate两极式（模具）segregation偏析well type蓄料井selective hardening部分淬火insulated runner绝缘浇道方式shot blast喷丸处理hot runner热浇道shot peening珠击法runner plat浇道模块single stage nitriding等温渗氮valve gate阀门浇口sintering烧结处理band heater环带状的电热器soaking均热处理spindle阀针softening软化退火spear head刨尖头solution treatment固溶化热处理slag well冷料井spheroidizing球状化退火cold slag冷料渣stabilizing treatment安定化处理welding line熔合痕straightening annealing矫直退火eject pin顶出针strain ageing应变老化knock pin顶出销stress relieving annealing应力消除退火return pin回位销反顶针subzero treatment生冷处理sleave套筒supercooling过冷insert core放置入子surface hardening表面硬化处理runner stripper plate浇道脱料板temper brittleness回火脆性guide pin导销，导正销，定位temper colour回火颜色lifter guide pin浮升导料销tempering回火eject rod (bar)（成型机）顶业捧tempering crack回火裂痕subzero深冷处理 texture咬花three plate三极式模具thermal refining调质处理three plates mold三片式模具 thermoechanical treatment加工热处理runner system浇道系统time quenching时间淬火stress crack应力电裂transformation变态orientation定向tufftride process软氮化处理sprue gate射料浇口，直浇口under annealing不完全退火nozzle射嘴vacuum carbonitriding真空渗碳氮化sprue lock pin料头钩销(拉料杆)vacuum carburizing真空渗碳处理side gate侧浇口vacuum hardening真空淬火edge gate侧缘浇口 vacuum heat treatment真空热处理tab gate搭接浇口vacuum nitriding真空氮化slit gate缝隙浇口water quenching水淬火fan gate扇形浇口wetout浸润处理dish gate因盘形浇口焊接用语diaphragm gate隔膜浇口arc电弧ring gate环形浇口argon arc welding氩弧焊接subarine gate潜入式浇口bare electrode光熔接条tunnel gate隧道式浇口butt welding对接焊接pin gate针点浇口cascade阶迭熔接法Runner less无浇道clad weld被覆熔接(sprue less)无射料管方式crator焊疤long nozzle延长喷嘴方式excess metal多余金属sprue浇口;溶渣filler rod焊条各种模具常用成形方式fillet weld填角焊接powder forming粉末成形gas shield气体遮蔽calendaring molding压延成形groove welding起槽熔接powder metal forging粉末锻造hand face shield手握面罩cold chamber die casting冷式压铸hard facing硬表面堆焊precision forging精密锻造jig welding工模焊接cold forging冷锻laser beam welding雷射光焊接press forging冲锻metal electrode insert gas MIG熔接compacting molding粉末压出成形nugget点焊熔核rocking die forging摇动锻造overlaying堆焊compound molding复合成形peening of welding珠击熔接法rotary forging回转锻造plug welding塞孔熔接compression molding压缩成形positioned welding正向熔接rotational molding离心成形pressure welding压焊dip mold形浸渍成propane gas cutting丙烷气切割rubber molding橡胶成形pure nickel electrode纯镍熔接条encapsulation molding注入成形reinforcement of weld加强焊接sand mold casting砂模铸造resist抗蚀护膜extrusion molding挤出成形root running背面熔接shell casting壳模铸造seam裂痕foam forming发泡成形seaming接合，折弯重迭加工sinter forging烧结锻造seam welding流缝熔接six sides forging六面锻造series seam welding串联缝熔接gravity casting重力铸造skip welding process跳焊法slush molding凝塑成形spark火花hollow(blow) molding中空(吹出)成形spot welding点焊接squeeze casting高压铸造stitch welding针角焊接hot chamber die casting热室压铸stud arc welding电弧焊接swaging挤锻under laying下部焊层hot forging热锻void焊接空隙transfer molding转送成形weld flow mark焊接流痕injection molding射出成形weld flush焊缝凸起warm forging温锻weld line焊接纹investment casting失模铸造，精密铸造，weld mark焊接痕matched die method配合成形法，对模成形weld penetration熔接透入laminating method被覆淋膜成形weld zone焊接区low pressure casting低压铸造welding焊接lost wax casting脱蜡铸造welding bead焊接泡matched mould thermal对模热成形模welding direction焊接方向各式模具分类用语welding distortion焊接变形bismuth mold铋铸模welding flux焊剂landed plunger mold有肩柱塞式模具welding ground电熔接地burnishing die挤光模welding interval焊接周期landed positive mold有肩全压式模具welding stress熔接应变button die镶入式圆形凹模welding torch熔接气炬loading shoe mold料套式模具射出成形关联用语center-gated mold中心浇口式模具bag moulding气胎施压成形loose detail mold活零件模具bonding strength黏合强度chill mold冷硬用铸模breathing排气loose mold活动式模具caulking compound填隙料clod hobbing冷挤压制模cell单元louvering die百叶窗冲切模cold slug半凝式射出composite dies复合模具colorant着色剂manifold die分歧管模具color matching调色counter punch反凸模color masterbatch色母料modular mold组合式模具compound混合料double stack mold双层模具copolymer共聚合体multi-cavity mold多模穴模具cull残料废品electroformed mold电铸成形模cure凝固化multi-gate mold复式浇口模具cryptometer不透明度仪expander die扩径模daylight开隙offswt bending die双折冷弯模具dry cycle time空料试车周期时间extrusion die挤出模ductility延性palletizing die迭层模elastomer弹性体family mold反套制品模具extruded bead sealing压出粒涂层法plaster mold石膏模feed供料blank through dies漏件式落料模filler充填剂porous mold通气性模具film blowing薄膜吹制法duplicated cavity plate复板模floating platen活动模板positive mold全压式模具foaming agent发泡剂fantail die扇尾形模具gloss光泽pressure die压紧模granule颗粒料fishtail die鱼尾形模具gunk料斗profile die轮廓模hot mark热斑flash mold溢料式模具hot stamping烫印progressive die顺序模injection nozzle射出喷嘴gypsum mold石膏铸模injection plunger射出柱塞protable mold手提式模具injection ram射出冲柱hot-runner mold热流道模具isomer同分异构物prototype mold雏形试验模具kneader混合机ingot mold钢锭模leveling agent匀涂剂punching die落料模lubricant润滑剂lancing die切口模mould clamping force锁模力re-entrant mold凹入模，侧凹模，倒角mould release agent脱模剂sectional die对合模具，拼合模，组oriented film取向薄膜runless injection mold无流道冷料模具parison吹气成形坏料segment mold组合模pellet粒料semi-positive mold半全压式模具plasticizer可塑剂shaper牛头刨床，定型模套，plunger压料柱塞single cavity mold单腔模具porosity孔隙率solid forging die整体锻模post cure后固化split forging die拼合锻模premix预混料split mold双并式模具purging清除sprueless mold无注道残料模具reciprocating screw往复螺杆squeezing die挤压模resilience回弹性stretch form die拉伸成形模resin injection树脂射出法sweeping mold平刮铸模rheology流变学swing die振动模具sheet塑料片trimming die切边模shot注射unit mold单元式模具shot cycle射出循环universal mold通用模具slip agent光滑剂unscrewing mold退扣式模具take out device取料装置yoke type die轭型模toggle type mould clamping肘杆式锁模装置模具厂常用之标准零配件torpedo spreader鱼雷形分流板baffle调节阻板transparency透明性baffle plate挡块void content空洞率baffle plate折流檔板塑料原料ball button球塞套acrylic压克力ball plunger定位球塞casein酪素ball slider球塞滑块cellulose acetate醋酸纤维素CAblank holder防皱压板cellulose acetate butyrate醋酸丁酸纤维素CAB bottom board浇注底板composite material复合材料bolster上下模板，垫板cresol resin甲酚树脂CFbottom plate下托板(底板)dially phthalate苯二甲酸二烯丙酯bottom plate下固定板disperse reinforcement分散性强化复合材料bracket小磁导engineering plastics工程塑料bracket扥架epoxy resin环氧树脂EPbumper block缓冲块ethyl cellulose乙基纤维素buster堵口ethylene vinylacetate乙烯-醋酸乙烯EVA casting ladle浇注包ethylene-vinlacetate copolyme醋酸乙烯共聚物EVA casting lug铸耳expanded polystyrene发泡聚苯乙烯EPS cavity模穴(模仁)fiber reinforcement纤维强化热固性/纤维强cavity retainer plate模穴扥板high density polyethylene高密度聚乙烯HDPEcenter pin中心梢high impact polystyrene高冲击聚苯乙烯HIPS clamping block锁定块high impact polystyrene高冲击性聚苯乙烯coil spring螺旋弹簧low density polyethylene低密度聚乙烯LDPE cold punched nut冷冲螺母melamine resin三聚氰胺酚醛树脂MF cooling spiral螺旋冷却栓nitrocellulose硝酸纤维素core心型phenolic resin酚醛树脂core pin心型梢plastic塑料cotter开口梢polyacrylic acid聚丙烯酸PAPcross十字接头polyamide耐龙PAcushion pin缓冲梢polybutyleneterephthalate聚对苯二甲酸丁酯PBT diaphragm gate盘形浇口polycarbonate聚碳酸酯PCdie approach模口角度，模头料道polyethyleneglycol聚乙二醇PFGdie bed型底polyethyleneoxide聚氧化乙烯PEOdie block块形模体polyethyleneterephthalate聚乙醇对苯PETPdie body铸模座polymetylmethacrylate聚甲基丙烯酸甲酯die bush合模衬套polyoxymethylene聚缩醛POMdie button冲模母模polyphenylene oxide聚硫化亚苯die clamper夹模器polyphenyleneoxide聚苯醚PPOdie fastener模具固定用零件polypropylene聚丙烯PPdie holder母模固定板polystyrene聚苯乙烯PSdie lip模唇polytetrafluoroethylene聚四氟乙烯PTFEdie plate冲模板polythene聚乙烯PEdie set冲压模座polyurethane聚氨基甲酸酯PU direct gate直接浇口polyvinylacetate聚醋酸乙烯PVACdog chuck爪牙夹头polyvinylalcohol聚乙烯醇PVAdowel hole导套孔polyvinylbutyral聚乙烯醇缩丁醛PVB dowel pin合模梢，固定、定位梢polyvinylchloride聚氯乙烯PVCdozzle辅助浇口polyvinylfuoride聚氟乙烯PVFdraft拔模锥度polyvinylidenechloride聚偏二氯乙烯PVDC draw bead张力调整杆prepolymer预聚物drive bearing传动轴承silicone resin硅树脂ejection pad顶出衬垫thermoplastic热塑性ejector脱模器thermosetting热固性ejector guide pin顶出导梢thermosetting plastic热固性塑胶ejector leader busher顶出导梢衬套unsaturated polyester不饱和聚酯树脂ejector pad顶出垫模具常用刀具与工作法用语ejector pin顶出梢anvil铁钻ejector plate顶出板arbour心轴ejector rod顶出杆backing sand背砂ejector sleeve顶出衬套backing衬垫ejector valve顶出阀buffing wheel抛光布轮eye bolt环首螺栓buffing抛光filling core椿入蕊，埋入砂心chamfering machine倒角机film gate薄膜形浇口chamfering tool去角刀具finger pin指形梢chisel扁錾finish machined plate角形模板chuck夹具finish machined round圆形模板compass两角规fixed bolster plate固定侧模板concave cutter凹面铣刀flanged pin带凸缘销convex cutter凸形铣刀flash gate毛边形浇口，闸门浇口cross joint十字接头flask上箱cutting edge clearance刃口余隙角floating punch浮动冲头drill stand钻台gate浇口edge file刃用锉刀gate land浇口面file锉刀gib凹形拉紧销，滑块引导flange joint凸缘接头goose neck鹅颈管grinder砂轮机guide bushing引导衬套hammer铁锤guide post引导柱hand brace手摇钻guide rail导轨hatching剖面线head punch顶镦冲头hexagon headed bolt六角头螺栓headless punch直柄冲头hexagon nut六角螺帽heavily tapered solid整体模蕊盒index head分度头hose nippler管接头jack千斤顶impact damper缓冲器kit工具箱injection ram压射柱塞lapping研磨inlay busher嵌入衬套metal saw金工锯inner plunger内柱塞nose angle刀角inner punch内冲头pinchers钳子insert入块(嵌入件)pliers铗钳insert pin，retainer pin嵌件梢plug柱塞头king pin转向梢polisher磨光器king pin bush主梢衬套protable driller手提钻孔机knockout bar脱模杵sand paper砂纸land area合模面scraper刮刀leader busher导梢衬套screw driver螺丝起子lifting pin起模顶销scribing划线lining内衬second out file中纹锉locating center punch定位中心冲头spanner扳手locating pilot pin定位导梢spline broach方栓槽拉刀locating ring定位环square sleeker方形镘刀lock block压块square trowel直角度locking plate定位板stripping剥离工具loose bush活动衬套T-slot T形槽making die打印冲子 tool for lathe车刀manifold block歧管档块tool point angle刀刃角master plate靠模样板tool post刀架match plate分型板tosecan划线盘mold base塑料模座waffle die flattening压纹效平mold clamp铸模紧固夹wiper脱模钳mold platen模用板wrench螺旋扳手moving bolster换模保持装置计算机关联用语moving bolster plate可动侧模板3D modeling三次元模拟one piece casting整体铸件bug瑕疵parallel block平行垫块bus总线paring line分模线CAD计算机辅助设计parting lock set合模定位器CAE计算机辅助工程分析pass guide穴型导板CAM计算机辅助制造peened head punch镶入式冲头cassette卡座pilot pin导销 color display彩色显示器pin gate针尖浇口command指令fardage，sarking衬板communication通信pre extrusion punch顶挤冲头compact精简小型puncher推杆computer计算机pusher pin衬套梢copy复制rack机架cursor游标rapping rod起模杆curve modeling曲面仿真retainer plate扥料板database数据库return pin回位梢digitizing数字化riding stripper浮动脱模器disk磁盘ring gate环型浇口dot点roller滚筒eyelet眼孔runner跑步者，流道floppy磁盘片runner ejector set流道顶出器format格式化runner lock pin流道拉梢graphic圆解screw plug头塞hardware硬件set screw固定螺丝honeycomb蜂巢shedder ，knockout脱模装置interface界面shim分隔片know how秘诀shoe模座之上下模板laser printer激光打印机shoot拍摄，流道lay out布置shoulder bolt肩部螺丝memory记忆skeleton骨架memory swap交换记忆slag riser冒渣口microprocessor微处理器slide(slide core)滑动，滑块，滑心modeling造型slip joint滑配接头module，die block模块spacer block间隔块monitor屏幕spacer ring间隔环mouse鼠标spider模蕊支架need，Requirement,Demand需求spindle主轴network网络sprue注道new version新版sprue bushing注道衬套on line上线中sprue bushing guide注道导套option选择权sprue lock bushing注道定位衬套plotter绘图机sprue puller注道拉料销program，Procedure程序spue line合模线scanning扫描square key方键simulation仿真square nut方螺帽software软件square thread方螺纹solid model实体模型stop collar限位套system系统stop pin止动梢tape磁带，胶带stop ring止动环terminal终端机,端子stopper定位停止梢texture构造straight pin圆柱销venter排气风扇stripper bolt脱料螺栓word processor文书处理器stripper bushing脱模衬套各种冲模加工关连用语stripper plate剥料板blanking die落料冲头stroke end block行程止梢blanking穿落模，下料support pillar支撑支柱/顶出支柱blanking下料加工support pin支撑梢bulging撑压加工supporting plate扥板burring冲缘加工sweep templete造模刮板cam die bending凸轮弯曲加工tab gate辅助浇口caulking铆合加工taper key推拔键coining压印加工taper pin拔锥梢/锥形梢compressing压缩加工teeming浇注compression bending押弯曲加工three start screw三条螺纹crowning凸面加工thrust pin推力销curl bending卷边弯曲加工tie bar拉杵curling卷曲加工tunnel gate隧道形浇口cutting切削vent通气孔dinking切断蕊骨wortle plate拉丝模板double shearing迭板裁断模具加工方法drawing引伸加工bending stress弯曲应力drawing with ironing抽引光滑加工bending弯曲加工extrusion挤制加工bending moment弯矩fine blanking精密下料加工bending block，form折刀finish blanking光制下料加工broaching拉刀切削finishing精整加工centering定中心flanging凸缘加工cylindrical lathe cutting外圆车削folding折边弯曲加工,折迭加工electric discharge machine放电加工forming ，shaping成形加工，组成，计划electrolytic grinding电解研磨impact extrusion冲击挤压加工facing面车削indenting压痕加工hand finishing手工修润ironing引缩加工hemming卷边加工louvering百叶窗板加工hobbing滚齿加工marking刻印加工joggling摇动加工notching冲口加工laser beam machining雷射加工parting分断加工lathe cutting车床车削piercing冲孔加工planning刨削加工progressive bending连续弯曲加工polishing抛亮光progressive blanking连续下料加工rough machining粗切削progressive drawing连续引伸加工rounding圆形加工progressive forming连续成形加工sawing锯削reaming铰孔修润，铰孔加工scaling清除钢碇缺陷restriking二次精冲加工skiving表面研磨riveting铆接加工slotting切缝切削roll bending滚筒弯曲加工taper turning锥度车削roll finishing滚压加工thread cutting螺纹切削rolling压延加工ultrasonic machining超音波加工roughing粗加工up cut milling逆铣加工scrapless machining无废料加工锻铸造关连用语shaving缺口修整加工airless blasting cleaning离心喷光shearing切断加工all round die holder通用模座sizing精压加工/矫正加工assembly mark铸造合模记号slitting切缝量，割缝加工back pouring补浇注spinning卷边铆接base bullion粗金属锭staking铆固base permeability原砂透气度stamping锻压加工belling压凸，压凸加工swaging挤锻压加工billet坏料trimming去毛边，整缘加工bleed漏铸upsetting锻粗加工blocker预锻模膛wiring抽线加工blocking粗胚锻件质量人员名称类blow hole破孔，铸件气孔QC quality control品质管理人员board drop hammer板落锤FQC final quality control终点质量管理人员bottom pour mold底浇IPQC in process quality制程中的质量管理人员bottom pouring底注OQC output quality control最终出货质量管理人员boxless mold脱箱砂模IQC incoming quality control进料质量管理人员break-off core缩颈砂心TQC total quality control ，全面质量管理brick molding砌箱造模法POC passage quality control段检人员buckle剥砂面QA Quality Assurance质量保证(处)，质量保证camlachie cramp铸包OQA output quality出货质量保证人员cast blade铸造叶片质量保证类casting flange铸造凸缘FAI first article inspection新品首件检查casting on flat水平铸造FAA first article assurance首件确认cleaning of casting ，铸件清理TVR tool verification report模具确认报告core template砂心模板3B 3B 模具正式投产前确core vent砂蕊排气孔capability index能力指数CPcorner gate压边浇口CPK capability index of模具制程能力参数counter lock止口镶嵌方式SSQA standardized supplier合格供货商质量评估draw out拉拔、锻造拔长OOBA out of box audit开箱检查draw plate起模板QFD quality function质量机能展开draw spike起模长针8 disciplines8项回复内容dummying预锻FA final audit最后一次稽核embedded core加装砂心CAR corrective action改正行动要求erosion冲砂corrective action report改正行动报告filling in填砂FQC运作类finishing slag炼后熔渣flash gutter锻模飞边槽flask molding砂箱造模hammer man锻工heading machine顶镦机impacter卧式锻造机inblock cast整体铸造ingot铸锭ingot blank铸坯inlay casting镶铸法loose piece木模活块molding pit铸模地坑pouring process浇注法recasting重铸rolled surface轧制表面rough sand粗砂roughing forge粗锻sand crushing塌箱seamless forging无缝锻造slag熔渣slag inclusion夹渣strip layout带状胚料排样法tap casting顶注top gate顶注浇口unworked casting不加工铸件upender翻转装置upending顶锻uphill casting底铸white cast iron白口铸件。
常用塑胶英语词汇以及与客户沟通邮件语句
DFM English and design Principles一．产品信息： Product information1. 外观： Surface Appearance2. 光洁度： Glossiness/gloss finish3. 毛面： Matt finish/matt surface4. 皮纹粒度： Grain5. 特殊皮纹区域： Special area texture6. 塑料色母 : M aster batch7. 烫金 / 涂层 / 印刷 / 雾晕 H ot stamping/ coating/ print/ haze8. 仿皮革 : leather cloak9. 电火花纹： EDM10. 光化学腐蚀法： Photochemical etching11. 刷涂纹，拉丝纹 Brushing12. 激光雕刻： Laser engraving13. 喷砂： Sand blasting1. 设计版本 : D esign revision2. 产品重量： part weight3. 注射重量： Shot weight4. 流道重量： R unner weight5. 驻留时间： Resident time6. 缩水率： Shrinkage7. 最终外观： Cosmetic finishing:8. 塑胶材料： Resin material9. 塑胶等级： Resin Grade10. 产品体积： part volume二．浇口类型： G ate type自动脱模浇口 Automatic gate1. 潜伏式浇口： Submarine gate2. 香蕉形浇口： Cashew gate ， banana gate3. 针点式浇口： Pin gate4. 热浇道口： Hot drop5 针阀浇口： Valve gate手动整理浇口 Manual gate1. 边缘浇口： Edge gate2. 凸耳浇口： Tab gate overlap gate3. 直接浇口： Sprue gate4. 隔膜浇口： Diaphragm gate5. 环形浇口： Ring gate6. 扇形浇口： Fan gate7. 薄膜浇口： Flash gate8. 过滤器瞟浇口： Filter Rowl gate说明： illustrate●浇口进入位： G ate location●浇口大小： Gate size●转水口： Switching runner / gate ●唧嘴口径： Sprue diameter●水口殘留最大 0.1m m. T he maximal residual gate is 0.1mm . Gates Vestige will be 0.1mm●此水口会用 CNC 铣平 : T he gate will be milled to flat by CNC.●此位会作凹陷 Here will be recess.●浇口需要冲床机器二次加工来去除： Gates n eed 2nd p rocess r emove by stamping machining●透明件不宜用香蕉浇口，易见流痕： The banana gate does not suite the transparent part. F low mark is visible.●最终的进胶位置根据模流分析： Finally gate position according the mold flow analysis.●顶出后额外的墙被切掉 : Extra wall t o be cut away after ejection●是否可以添加一个小肋骨用来放潜水口 , 成型后再删除它如果必要的话：Is it possible to add one small rib to place sub gate, after molding remove it by operator if necessary三．流道 : runner●冷流道： C old runner1. 唧嘴直流 : Direct sprue gate2. 圆形流道： R ound(full/half ) runner3. 正圆形： Full Round （最有效） Most Efficient4. 梯形： Trapezoidal ( 有效） Good5. 半圆形： Half Round （非有效） N ot Good●热流道： Hot runner1. 热流道板： H ot manifold2. 热嘴转冷流道 : hot sprue turn to cold runner3. 热流道转冷流道 : hot tips turn to cold runner●冷料井— cold slug well说明： illustrate●单嘴阀针式热流道转冷流道 : 1 drops valve nozzle to cold runner●单嘴尖点式热流道转冷流道 : 1 drops tip nozzle to cold runner●单嘴开放式热流道转冷流道 : 1 drops open nozzle to cold runner● 2 点针阀式直接进胶 : Hot runner 2 drops valve nozzle direct to part●喷嘴 Nozzle设计原则： Design principles●根据模流分析结果最后确定浇口位置： Finally gate position according the mold flow analysis●检查流动长度在薄壁产品： check f low length in thin walled part●竖浇道太长了约有 200mm 長 . 冷流道系统流动不均 , 推荐使用热流道以使流动较佳 . The sprue will be too long if we use cold runner design. Its length is around 200 millimeters ， Flow imbalance by cold runner ， We recommend a hot runner system for better flow.●浇道系统应该有一个均衡的布局： R unner system should have a balanced layout●省料： Savings in material●周期短： Shorter cycles●浇口在最佳位置： Gates at the best position●压力降最小： Pressure losses minimized●人工系统流道平衡： Artificial balancing of the gate system●避免焊缝线 : Avoidance of weld line●纤维取向 : Fiber orientation●避免迟滯效应： Avoid the hysteresis effect●避免潜流： avoid underflow●所有的流道都要有冷料井： All runners are to have cold slug wells ●多型腔模具浇口尺寸必须相同，平衡必须经过调整流道而不是调整浇口。
塑料制品企业常用的英语词汇
七.QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan,产品质量先期策划和控制计划uPPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析MSA Measure System Analysis,测量系统分析SPC Statistical Process Control,统计过程控制审核Audit能力Capability能力指数Capability Indices控制计划Control Plans 纠正措施Corrective Action 文件Documentation作业指导书Job Instruction, work instruction 不合格品Nonconformance不合格Nonconformity每百万零件不合格数Defective Parts Per Million, DPPM预防措施Preventive Action 程序Procedures 过程流程图Process Flow Diagram, Process Flow Chart质量手册Quality Manual质量计划Quality Plan质量策划Quality Planning质量记录Quality Records原始数据Raw Data反应计划Reaction Plan返修Repair o返工Rework现场Site分承包方Subcontractors产品product质量quality质量要求quality requirement顾客满意customer satisfaction质量管理体系quality management system 质量方针quality policy质量目标quality objective质量管理quality management质量控制quality control质量保证quality assurance 组织organization顾客customer供方supplier过程process月艮务service设计与开发design and development：特性characteristic可追溯性trace ability合格conformity缺陷defect纠正correction让步concession放彳亍release报废scrap规范specification检验inspection试验test验证verification评审review测量measurement计数型数据Attributes Data普通原因Common Cause单值Individual均值Mean随机抽样Random Sampling极差Range特殊原因Special Cause稳定性Stability子组Subgroup计量型数据variables Data变差variation固有变差Inherent variation总变差Total variation偏倚Bias重复性Repeatability再现性Reproducibility稳定性Stability线性Linearity分辨率Resolution过程更改Process change质量功能展开QFD过程特殊特性Special Process Characteristic 产品特殊特性Special Product Characteristic 外观项目Appearance Item初始过程能力Preliminary Process Capability 材料清单Bill of Material设计确认Design Validation设计验证Design Verification顾客的呼声Voice of the Customer 过程的呼声Voice of the Process 八.常用缩略词语1、ES 工程规范Engineering Specification2、KCC 关键控制特性（GM）Key Control Characteristic3、KPC 关键产品特性（GM）Key Product Characteristic4、OEM 整车厂Original Equipment Manufacturer5、SC 重要（特殊）特性Significant（Special） Characteristic6、ANOVA 方差分析法Analysis of variance7、CFT 多方论证小组Cross function Team8、DFMEA设计失效模式及后果分析Design Failure Mode and Effects Analysis 9、DOE 试验设计Design of Experiment 10、DVP&R设计验证计划和报告Design verification Plan and Report11、FTC 试生产能力First Time Capability12、GR&R量具的重复性和再现性Gage Repeatability and Reproducibility13、PFMEA过程失效模式及后果分析Process Failure Mode and Effect Analysis 14、SFMEA系统失效模式及后是分析System Failure Mode and Effect Analysis15、QSR 质量体系要求Quality System Requirement16、QFD 质量功能展开Quality function Deployment17、TGR 运行情况良好Things Gone Right18、TGW 运行情况不良Things Gone Wrong19、VE/VA价值工程/价值分析Value Engineering/Value Analysis20、BOM 物料清单Bill of Material21、Cpk稳定过程的能力指数Capability for stable process22、LCL 下控制限Lower Control Limit 23、UCL 上控制限Upper Control Limit 24、LSL 工程规范下限Lower Specification Limit 25、USL 工程规范上限Upper Specification Limit26、Ppk 性能指数The performance index27、MRB 物料评审Material Review Board28、PSW 零件提交保证书Part Submission Warrant29、X（一）--R图均值一极差图Average-Range Chart30、SRPC 供方要求产品更改Supplier Request for Product Change31、SREA供方工程批准的要求Supplier Request for Engineering Approval32、IAA 临时批准授权Interim Approval Authorization33、AAR 外观件批准报告Appearance Approval Report34、PTR 试生产（报告）Production Trial Run （Report）35、DCP尺寸控制计划（动态控制计戈U）Dimension Control Plan （Dynamic Control Plan）37、防错（POKA-YOKE）Mistake Proofing 加工订单Fabrication Order补足欠交Fill Backorder总装提前期Final Assembly Lead Time 确认的计划订单Firm Planned Order 固定订货批量F ixed Order Quantity 集中预测Focus Forecasting 完全踉踪Full Pegging通用生产管理原则Generally Accepted Manufacturing Practices毛需求Gross Requirements 在制品库存In Process Inventory 独立需求Independent Demand 投入/产出控制Input/ Output Control 检验标识Inspection ID 厂际需求Interplant Demand 库存周转率Inventory Carry Rate 仓库库位类型Inventory Location Type库存周转次数Inventory Turnover 发送订单Issue Order项目记录Item Record物料项目Item加工车间Job Shop准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time层Level负荷量Load Leveling负荷报告Load Report负荷Load仓位代码Location Code仓位备注Location Remarks仓位状况Location Status按需订货Lot for Lot批量标识Lot ID批量编号Lot Number批量Lot Size低位码Low Level Code 机器能力Machine Capacity 机器加载Machine Loading 外购或自制决策Make or Buy Decision 面向订单生产的产品Make-to-order Product 面向库存生产的产品Make-to-stock Product 制造周期时间Manufacturing Cycle Time制造资源计戈U Manufacturing Resource Planning (MRP II)主生产计划Master Production Schedule (MPS)物料成本Material Cost物料发送和接收Material Issues and Receipts 物料需求计划Material Requirements Planning (MRP)登陆标志MPS Book Flag MPS 多重仓位Multiple Location 净改变式MRP N et Change MRP 净需求Net Requirements 新仓位New Location新组件New Parent新仓库New Warehouse 不活动报告No Action Report现有库存量On-hand Balance未结订单Open Order订单输入Order Entry订货点Order Point订货方针Order Policy订货承诺Order Promising订货备注Order Remarks 双亲Parent零件清单Part Bills零件批次Part Lot零件编号Part Number零件Part反查Pegging领料单Picking List领料/提货Picking计划订单Planned Order后减库存处理法Post-deduct Inventory Transaction Processing前减库存处理法Pre-deduct Inventory Transaction Processing发票价格Price Invoice采购订单价格Price Purchase Order优先计划Priority Planning产品控制Product Control产品线Production Line生产规划编制Production Planning产品率Production Rate产品结构树Production Tree预计可用库存Projected Available Balance采购订单是艮踪Purchase Order Tracking已分配量Quantity Allocation仓位数量Quantity At Location欠交数量Quantity Backorder完成数量Quantity Completion需求量Quantity Demand毛需求量Quantity Gross进货数量Quantity In排队时间Queue Time队列Queue重生成式MRP Regenerated MRP重排假设Rescheduling Assumption资源需求计划Resource Requirements Planning粗能力计划Rough-cut Capacity Planning 工艺路线Routing 安全库存量Safety Stock 保险期Safety Time 预计入库量Scheduled Receipt 残料率Scrap Factor 发送零件Send Part 维修件Service Parts 发货地址Ship Address 发货单联系人Ship Contact 发货零件Ship Date 发货单Ship Order 工厂日历Shop Calendar 车间作业管理Shop Floor Control 损耗系数Shrinkage Factor 标准产品成本Standard Product Cost 标准机器设置工时Standard Set Up Hour 标准单位运转工时Standard Unit Run Hour 标准工资率Standard Wage Rate 状况代码Status Code 库存控制Stores Control建议工作单Suggested Work Order 约束理论Theory of Constraints (TOC) 时间段Time Bucket 时界Time Fence单位成本Unit Cost采购计划员Vendor Scheduler 采购计划法Vendor Scheduling 工作中心能力Work Center Capacity 工作中心Work Center 在制品Work in Process工作令是艮踪Work Order Tracking工作令Work Order工作进度安排Work Scheduling 零库存Zero Inventories经济订货批量=$4口放(2*年订货量*平均一次订货准备所发生成本/每件存货的年储存成本)美国生产和库存控制协会APICS, American Production & Inventory Control Society 五、生产注塑机injection machine 冲床Punch machine 混料机blender mixer 尼龙nylon黄铜brass 青铜bronze 紫(纯)铜copper 料斗hopper 麻点pit酉己料compounding涂层coating 飞边flash 预热preheating 再生料reworked material 再生塑料reworked plastics 工艺设计process design 紧急停止emergency stop 延时time delay六.物控保质期shelf lifeABC 分类法ABC Classification 反常需求Abnormal Demand 措施信息Action Message 活动报告标志Action-report-flag 基于活动的成本核算Activity-based Costing (ABC)实际能力Actual Capacity实际成本Actual Costs调整现有库存量Adjust-on-hand已分配量Allocation替代工序Alternative Routine 装配订单Assembly Order 装配零件表Assembly Parts List 装配Assembly计划自动重排Automatic Rescheduling 可达到库存Available Inventory 可用材料Available Material达到库存Available Stock 可利用工时Available Work 可签约量Available-to-promise 平均库存Average Inventory 欠交订单Back Order倒序计划U Back Scheduling 倒冲法Back flush未完成订单Backlog现有库存余额Balance-on-hand Inventory 批号Batch Number批量生产Batch Production标杆瞄准Benchmarking 工时清单Bill of Labor 提货单Bill of Lading 物料清单Bill of Material 分库Branch Warehouse 经营规划Business Plan 采购员Buyer 能力管理Capacity Management 能力需求计划Capacity Requirements Planning (CRP) 保管费率Carrying Cost Rate 保管费Carrying Cost 单元式制造Cellular Manufacturing 修改批量日期Change Lot Date 修改工序Change Route 修改产品结构Change Structure 检查点Check Point 闭环物料需求计划Closed Loop MRP 通用工序标识Common Route ID计算机集成制造Computer-integrated Manufacturing (CIM)配置代码Configuration Code约束管理/约束理论Constraints Management/Theory of Constraints (TOC) 依成本的材料清单Costed Bill of Material 急需零件Critical Part累计提前期Cumulative Lead Time 现有运转时间Current Run Hour 现有运转数量Current Run Quantity 周期盘点Cycle Counting 调整日期Date Adjust 有效日期Date Available 修改日期Date Changed 结束日期Date Closed 截止日期Date Due 生产日期Date in Produced 库存调整日期Date Inventory Adjust 作废日期D ate Obsolete 收到日期Date Received 交付日期Date Released 需求日期Date Required 发货日期Date to Pull 空负荷Dead Load 需求管理Demand Management需求Demand实际能力Demonstrated Capacity非独立需求Dependent Demand直接增减库存处理法Direct-deduct Inventory Transaction Processing发料单Disbursement List派工单Dispatch List分销资源计划Distribution Resource Planning (DRP)鼓一缓冲一绳子Drum-buffer-rope经济订货批量Economic Order Quantity (EOQ)工程变更生效日期Engineering Change Effect Date工程变更生效单Engineering Change Effect Work Order工程停止日期Engineering Stop Date例外控制Exception Control呆滞材料分析Excess Material Analysis急送代码Expedite Code三、模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan 型芯固定板core-retainer plate凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould 多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould，Fixed mould 动模movable mould, movable half 上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孑L dowel hole 型芯core斜销angle pin, finger cam 滑块slide滑块导板slide guide strip 楔紧块heel block, wedge lock 拉料杆sprue puller 定位环locating ring 冷却通cooling channel 脱模斜度draft 滑动型芯slide core 螺纹型芯threaded core 热流道模具hot-runner mould 绝热流道模insulated runner mould 熔合纹weld line (flow line) 三板式模具three plate mould 脱模ejection换模腔模具interchangeable cavity mould 脱模剂release agent 注射能力shot capacity 注射速率injection rate 注射压力injection pressure 差色剂colorant 保压时间holdup time 闭模时间closing time 定型装置sizing system 阴模female mould，cavity block 阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center 万能铁床Universal milling machine 卧式刨床Horizontal planer 车床Engine lathe 平面磨床Surface grinding machine 去磁机Demagnetization machine 万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine 四、品管SPC statistic process control 品管保证Quality Assurance 品管控制Quality control 来料检验IQC Incoming quality control 巡检IPQC In-process quality control 校对calibration动态试验dynamic test环境试验Environmental test 非破坏性试验non-destructive test 光泽gloss击穿电压(dielectric) breakdown voltage 拉伸强度tensile strength冷热骤变试验thermal shock test 环境试验炉Environmental chamber 盐雾实验salt spray test绝缘电阻测试验仪Insulating resistance meter 内应力internal stress疲劳fatigue蠕变creep试样specimen 撕裂强度tear strength 缩痕shrink mark, sink mark 耐久性durability才由样sampling 样品数量sample sizeAQL Acceptable Quality level批量lot size抽样计戈U sampling planOC 曲线operation curve 试验顺序sequence of tests 环境温度ambient temperature 可焊性solderability 阻燃性flame resistance 一、组织机构及职位XX 电子有限公司XX Electronics CO., Ltd 总经理办公室General manager' s office 企管部Enterprise management department (EM)行政部Administration department (AD) 销售部Sales department (SD)财务部Financial department (FD) 技术部Technology department (TD)物控部Production material control department (PMC)生产部Production department(PD)模具部Mold manufacturing department, Tooling manufacturing department (TM) 品管部Quality Assurance department (QA) 冲压车间Stamp workshop, press workshop 注塑车间injection workshop 装配车间Assembly workshop 模具装配车间Mold and die Assembly workshop 金属加工车间metal machine workshop 电脉冲车间Electric discharge process workshop 线切割车间wire cutting process workshop 工磨车间Grinding workshop 总经理General manager (GM) 副总经理Vice-general manager 经理manager 董事长president 副董事长Vice-president XX 部门经理Manager of XX department 主任、主管supervisor 拉长Line leader 组长Foreman, forelady 秘书secretary 文员clerk 操作员operator 助理assistant 一立口 -二*、^^品连接器connector 端子terminal 条型连接器bar connector 阴连接器Housing 阳连接器wafer 线束wire harness 间距space 额定电压rated voltage 额定电流rated current 接触电阻contact resistance 绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage 针pin 物料编号part number 导线wire 基体金属Base metal 电缆夹cable clamp 倒角chamfer 接触面积contact area 接触件安装孔contact cavity接触长度contact length 接触件电镀层contact plating 接触压力contact pressure 接触件中心距contact space 接触簧片contact spring 插孔socket contact 法兰、凸缘Flange 界面间隙interfacial gap 键Key 键槽key way 过渡段ramp 屏蔽套shielding 定位基准Datum reference 扁平电缆flat cable，Ribbon cable 柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printed circuit 焊盘pad 图形pattern 间距pitch 负极Negative pole 正极positive pole 回流Reflow原理图Schematic diagram 单面板single sided board 双面板Two-sided board, Double-sided board 表面安装surface Mounting 翘曲warp，bow 波峰焊wave soldering 编织层braid 同轴电缆coaxial cable 电介质dielectric 电缆中导线的头数ends 夕卜部干扰external interference 填充物filler 护套jacket 比重specific gravity电阻的温度系数Temperature coefficient of resistance。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
MDPE Medium-density polyethylene 中密聚乙烯
MF Melamine-formaldehyde resin 密胺-甲醛树脂
MPF Melamine/phenol-formaldehyde 密胺/酚醛树脂
PA Polyamide (nylon) 聚酰胺（尼龙）
HDPE High-density polyethylene plastics 高密度聚乙烯塑料
HIPS High impact polystyrene 高冲聚苯乙烯
IPS Impact-resistant polystyrene 耐冲击聚苯乙烯
LCP Liquid crystal polymer 液晶聚合物
PVC Poly(vinyl chloride) 聚氯乙烯
PVCA Poly(vinyl chloride-acetate) 聚氯乙烯醋酸乙烯酯
PVDC Poly(vinylidene chloride) 聚（偏二氯乙烯）
PVDF Poly(vinylidene fluoride) 聚（偏二氟乙烯）
常用塑料词汇（转贴）
少尉：haypiny(haypiny)
积分:301.7 声望:20
[查看该用户在资料中心上传的资料]
[个人资料] [给他留言] [帖子合集]
[回复] [引用] [维护]
--------------------------------------------------------------------------------
PF Phenol-formaldehyde resin 酚醛树脂
PFA Perfluoro(alkoxy alkane) 全氟烷氧基树脂
PFF Phenol-furfural resin 酚呋喃树脂
PI Polyimide 聚酰亚胺
PIB Polyisobutylene 聚异丁烯
常用塑料英语缩略语
英文简称 英文全称 中文全称
ABA Acrylonitrile-butadiene-acrylate 丙烯腈/丁二烯/丙烯酸酯共聚物
ABS Acrylonitrile-butadiene-styrene 丙烯腈/丁二烯/苯乙烯共聚物
AES Acrylonitrile-ethylene-styrene 丙烯腈/乙烯/苯乙烯共聚物
PPO Poly(phenylene oxide) deprecated 聚苯醚
PPOX Poly(propylene oxide) 聚环氧（丙）烷
PPS Poly(phenylene sulfide) 聚苯硫醚
PPSU Poly(phenylene sulfone) 聚苯砜
PS Polystyrene 聚苯乙烯
PAA Poly(acrylic acid) 聚丙烯酸
PADC Poly(allyl diglycol carbonate) 碳酸-二乙二醇酯· 烯丙醇酯树脂
PAE Polyarylether 聚芳醚
PAEK Polyaryletherketone 聚芳醚酮
PAI Polyamide-imide 聚酰胺-酰亚胺
PVF Poly(vinyl fluoride) 聚氟乙烯
PVFM Poly(vinyl formal) 聚乙烯醇缩甲醛
PVK Polyvinylcarbazole 聚乙烯咔唑
PVP Polyvinylpyrrolidone 聚乙烯吡咯烷酮
S/MA Styrene-maleic anhydride plastic 苯乙烯-马来酐塑料
PAK Polyester alkyd 聚酯树脂
PAN Polyacrylonitrile 聚丙烯腈
PARA Polyaryl amide 聚芳酰胺
PASU Polyarylsulfone 聚芳砜
PAT Polyarylate 聚芳酯
PAUR Poly(ester urethane) 聚酯型聚氨酯
SP Saturated polyester plastic 饱和聚酯塑料
SRP Styrene-rubber plastics 聚苯乙烯橡胶改性塑料
TEEE Thermoplastic Elastomer,Ether-Ester 醚酯型热塑弹性体
TEO Thermoplastic Elastomer, Olefinic 聚烯烃热塑弹性体
VCOA Vinyl chloride-octyl acrylate resin 氯乙烯/丙烯酸辛酯树脂
VCVAC Vinyl chloride-vinyl acetate resin 氯乙烯/醋酸乙烯树脂
PC Polycarbonate 聚碳酸酯
PCTFE Polychlorotrifluoroethylene 聚氯三氟乙烯
PDAP Poly(diallyl phthalate) 聚对苯二甲酸二烯丙酯
PE Polyethylene 聚乙烯
PEBA Polyether block amide 聚醚嵌段酰胺
TES Thermoplastic Elastomer, Styrenic 苯乙烯热塑性弹性体
TPEL Thermoplastic elastomer 热塑(性)弹性体
TPES Thermoplastic polyester 热塑性聚酯
TPUR Thermoplastic polyurethane 热塑性聚氨酯
PES Poly(ether sulfone) 聚醚砜
PET Poly(ethylene terephthalate) 聚对苯二甲酸乙二酯
PETG Poly(ethylene terephthalate) glycol 二醇类改性PET
PEUR Poly(ether urethane) 聚醚型聚氨酯
PISU Polyimidesulfone 聚酰亚胺砜
PMCA Poly(methyl-alpha-chloroacrylate) 聚α-氯代丙烯酸甲酯
PMMA Poly(methyl methacrylate) 聚甲基丙烯酸甲酯
PMP Poly(4-methylpentene-1) 聚4-甲基戊烯-1
PSU Polysulfone 聚砜
PTFE Polytetrafluoroethylene 聚四氟乙烯
PUR Polyurethane 聚氨酯
PVAC Poly(vinyl acetate) 聚醋酸乙烯
PVAL Poly(vinyl alcohol) 聚乙烯醇
PVB Poly(vinyl butyral) 聚乙烯醇缩丁醛
CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯
CS Casein 酪蛋白
CTA Cellulose triacetate 三醋酸纤维素
EC Ethyl cellulose 乙烷纤维素
EMA Ethylene/methacrylic acid 乙烯/甲基丙烯酸共聚物
TSUR Thermoset polyurethane 热固聚氨酯
UF Urea-formaldehyde resin 脲甲醛树脂
UHMWPE Ultra-high molecular weight PE 超高分子量聚乙烯
UP Unsaturated polyester 不饱和聚酯
VCE Vinyl chloride-ethylene resin 氯乙烯/乙烯树脂
AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物
ARP Aromatic polyester 聚芳香酯
AS Acrylonitrile-styrene resin 丙烯腈-苯乙烯树脂
ASA Acrylonitrile-styrene-acrylate 丙烯腈/苯乙烯/丙烯酸酯共聚物
EP Epoxy, epoxide 环氧树脂
EPD Ethylene-propylene-diene 乙烯-丙烯-二烯三元共聚物
EPM Ethylene-propylene polymer 乙烯-丙烯共聚物
EPS Expanded polystyrene 发泡聚苯乙烯
ETFE Ethylene-tetrafluoroethylene 乙烯-四氟乙烯共聚物
SAN Styrene-acrylonitrile plastic 苯乙烯-丙烯腈塑料
SB Styrene-butadiene plastic 苯乙烯-丁二烯塑料
Si Silicone plastics 有机硅塑料
SMS Styrene/alpha-methylstyrene plastic 苯乙烯-α-甲基苯乙烯塑料
CF Cresol-formaldehyde 甲酚-甲醛树脂
CMC Carboxymethyl cellulose 羧甲基纤维素
CN Cellulose nitrate 硝酸纤维素
CP Cellulose propionate 丙酸纤维素
CPE Chlorinated polyethylene 氯化聚乙烯
PB Polybutene-1 聚丁烯-[1]
PBA Poly(butyl acrylate) 聚丙烯酸丁酯
PBAN Polybutadiene-acrylonitrile 聚丁二烯-丙烯腈
PBS Polybutadiene-styrene 聚丁二烯-苯乙烯
PBT Poly(butylene terephthalate) 聚对苯二酸丁二酯
EVA Ethylene/vinyl acetate 乙烯-醋酸乙烯共聚物