木工加工中心详细介绍(英文对照)
木工机械专业词汇中英文对比精选版
木工机械专业词汇中英文对比Document serial number【KKGB-LBS98YT-BS8CB-BSUT-BST108】一画一字螺丝批 slot type screwdriver一点透视 one-point perspective二画二合一黏合剂 epoxy resin adhesive二合胶；混合胶 epoxy glue二维的；平面的 two-dimensional二进制 binary 二极管；整流子 diode二号螺丝攻 second tap 二路开关 two-way switch十进制的；公制的 metric 人工制品 artefact人造板 man-made board 人体工程学 ergonomics; human engineering人体尺寸 human dimension 人体测量学 anthropometry; anthropometrics刀片 blade 刀身 blade刀具 tool 刀具溜座 carriage刀柱 tool post 刀架 tool rest刀架底座 tool rest bracket 刀座帷；床鞍 apron刀座鞍；溜板座 saddle 力 force力三角形 triangle of force 力平行四边形 parallelogram of force力多边形；多边形力学 polygon of force 力的分解 force resolution力架；亮漆 lacquer 力矩 moment力偶 couple 力矩定律 law of moment力-距离图表 force-distance graph 力图 force diagram力线 line of force 力点 effort十字榫 cross halving joint 十字螺丝 Philip's head screw十字螺丝批 Philip's type screwdriver 丁字尺；T 尺 tee square三画三爪夹头three-jaw chuck三角尺 set square 三角形结构系杆 triangulation tie三角锉 triangular file 三维的；立体的 three-dimensional三氯甲烷；哥罗芳 chloroform三聚氰胺；蜜胺 melamine三点透视 three-point perspective 上油漆 painting上釉 enamelling 凡立水 varnish叉形顶尖 fork centre 口罩 mask士力；虫漆 shellac 士巴拿；扳手 spanner 大芯夹板；宽条芯夹板 blockboard;solid corestock-laminated board 大量制造 mass production子口刨；槽口刨；边刨 rebate plane 小型平槽刨 miniature router plane小型线料弯曲器 small wire bender 小型弯折机 mini bender小型电路断路器；跳菲 miniature circuit breaker (MCB) 小齿轮 pinion 山樟 San Cheong 工件 workpiece 工字梁 I beam工作面 working surface 工作图；制作图 working drawing工作台 bench; working table 工具 tool工具贮存室 tool storage 工具槽 well工具钢 tool steel 工场 workshop工场安全 workshop safety 工程字书写技巧 lettering工程系统 engineering system 工程绘图 engineering drawing工业酒精；火酒 methylated spirit 弓形手钻；手摇曲柄钻 brace 弓形手钻嘴 brace bit 弓锯 bow saw; hacksaw弓锯片 hacksaw blade弓锯床 hacksawing machine四画不平衡 imbalance不含铁金属；非铁金属 non-ferrous metal不贯穿孔；闭孔；盲孔 blind hole不贯穿鸠尾榫 lapped dovetail joint不对称 asymmetry不锈钢 stainless steel不稳定平衡 unstable equilibrium中心 centre中心线 centre line中心冲 centre punch中心钻 centre drill中心钻嘴 centre bit中央处理器 central processing unit (CPU)中性 neutral中性平衡；随遇平衡 neutral equilibrium中性轴 neutral axis中密度纤维板 medium density fibre board (MDF)中粗锉纹 second cut中碳钢 medium carbon steel中线 neutral wire互补金属氧化物半导体 complementary metal oxide semiconductors (CMOS)介子；垫片 washer介指铁 ring mandrel介电常数；电容率 permittivity介稳态的；亚稳态的 metastable内力 internal force内卡尺 inside calipers内能 internal energy内涵性质 intensive properties内圆弯凿 scribing gouge内锁式配件 interlocking fitting内燃机 internal combustion engine内螺纹制造法 tapping内螺丝 internal thread内弯边 concave edge六角金属枝 hexagonal bar六角匙 Allen key六角头螺丝 hexagonal head screw公制的；十进制的 metric公差 tolerance冗余构件 redundant member分力 component force分子 molecule分子力 molecular force分切；分割；切断 parting off分贝 decibel分析 analysis分析及批判学 analytical and critical studies 分析器 analyzer分流器 shunt分界面；界面；接口 interface分厘卡 micrometer分规 divider分割车刀架 parting tool holder分解 decomposition分压器 potential divider; voltage divider隔离开关 isolating switch切削工具 cutting tool切削液 cutting fluid切削深度 depth of cut切屑；碎屑 chip切线锯法 tangential sawing切辊纹；滚纹 knurling切断；分切；分割 parting off切断工具 parting tool勾；勾脚 hook勾刀；胶片刀 plastic cutter化胶水 tensol反向偏压 reverse biased反相放大器 inverting amplifier反相器 inverter反射 reflection反馈；回输 feedback天拿水；稀释剂 thinner天梯牙；齿条 gear rack天然木材 natural timber天然干燥法 air seasoning孔隙率 porosity尺寸 dimension尺寸线 dimension line尺身 blade引力；重力 gravitational force 心形凸轮 heart-shaped cam心材 heartwood心轴 mandrel心销 core pin手工具 hand tool手工锯 junior hacksaw手削法 paring手持虎钳 hand vice手柄 handle手套 gloves手扫漆 brushing lacquer手推车 barrow手提式竖线锯 portable jigsaw手提电动工具 portable power tool 手提电钻 electric hand drill手进给 hand feed手摇曲柄钻；弓形手钻 brace手摇钻 hand drill手锉 hand file手锯；板锯 handsaw手锥 bradawl手辘轧机 hand rolling machine支柱；支撑物 strut支架；支座 support支点 fulcrum; pivot文字 text方向 direction方向针 pointing needle方枝 square bar方波形 square waveform方波产生器 squarer方型牙板 rectangular die方格纸；网格纸 grid paper方通 square tube方块图 block diagram方锉 square file方头钻嘴 square shank bit方螺帽 square nut方边凿；直边凿 firmer chisel木 wood木工 woodwork木工工作间 woodwork area木工工作台 woodworker's bench木工车床 wood turning lathe; woodworking lathe木工铅笔 carpenter's pencil木工刨床 thicknessing and planning machine木牙螺丝；木螺钉 wood screw木材 timber木材车削 wood turning木材车削工具 wood turning tools木屑压合板；万花板 chipboard木条接榫 corner strip joint木圆头槌 doming mallet木模；模型 patterns木线 wood strip木胶粉 ureaformal dehyde resin glue木锉 rasp木螺钉；木牙螺丝 wood screw木槌 mallet止推轴承 thrust bearing止推垫圈 thrust washer比例 proportion比例尺 scale比例常数 proportionality constant比例极限 proportional limit比较器 comparator比热容量 specific heat capacity水平投影面 horizontal plane水平仪；平水尺 spirit level水气掣；漏电断路掣 earth leakage circuit breaker (ELCB) 水晶胶；聚酯树脂 polyester resin水晶胶的铸造成形 resin casting水磨砂纸 silicon carbide paper火叉 firing fork火水；煤油 kerosene火牛；变压器 transformer火石轮 grinder火花电蚀法；放电极加工 electrical discharge machining 火酒；工业酒精 methylated spirit火钳 tongs火线；活线 live wire火砖 fire brick爪扣；爪形离合器；犬齿式离合器 dog clutch牙板；丝模 die牙板扳手；丝模扳手 die holder (stock)牙板螺帽 die nuts牛皮胶；动物胶 animal glue牛油纸 tracing paper牛顿运动定律 Newton's laws of motion犬齿式离合器；爪扣；爪形离合器 dog clutch五画丙烯;丁二烯苯乙烯 acrylonitrile-butadiene-stryrene (ABS) 主轴；心轴 spindle主题 motif令(纸张的计数单位) ream凹座 recess凹模 hollowing block凸缘 flange凸缘联轴节 flange coupling凸轮 cam凸轮式配件 cam-action fitting凸轮传动 cam drive凸头螺丝 raised head screw加成作业；添加法 addition process加油 oiling加速器 accelerator功能；用途 function功率因子 power factor功率放大器 power amplifier功率板 power amplifier board功率晶体管 power transistor包氏记号法 Bow's notation「包浩思」；「包豪斯」〈设计风格) Bauhaus半永固法；半永久接合 semi-permanent joining半接榫 halving joint半闭式槽榫 stopped housing joint半圆(木)锉 half-round rasp半圆车刀 turning gouge半圆锉 half-round file半圆头铆钉 snap rivet半导体 semiconductor卡路里；卡(热量单位) calorie卡纸 card paper卡尺；测径器 calipers去角；倒角 chamfer可切削性 machinability可行性 feasibility可逆过程 reversible process可压缩性 compressibility可变电阻 variable resistor四分仪 quadrant四爪夹头 four-jaw independent chuck四圆心法(绘图) four-centre method外卡尺 outside calipers外形塑造 shaping外形线；轮廓线 outline外推法 extrapolation外圆弯凿 firmer gouge外螺纹 external thread外螺纹制造法 threading外弯边 convex edge外观 appearance失真 distortion尼龙；聚醯胺 nylon; polyamide (PA)尼龙墨水针笔 technical felt-tip pen左右调校杆 lateral adjusting level市售尺寸；标准尺寸 stock size市电频率；电源频率 mains frequency平(木)锉 flat rasp平水尺；水平仪 spirit level平行投影 parallel projection平行车削 parallel turning平行虎钳 parallel vice平行钉法 parallel nailing平底弯刨 flat faced spokeshave平底钻嘴 forstner bit平板结构 slab construction平流扼流圈；滤波扼流器 smoothing choke平流电容器；滤波电容器 smoothing capacitor 平流电路；滤汳电路 smoothing circuit平面板；正台 surface plate平面图；俯视图 plan平面锤 flatter平移 translation平搭榫 corner halving joint平嘴钳 flat nose pliers平槽刨 router plane平衡 balance; equilibrium平衡力 equilibrant平衡条件 equilibrium condition平衡电桥 balanced bridge平头弧刀 square nose gouge幼纹 smooth cut打凹成形 hollowing打凸成形 raising打槽机 routing machine打线；打槽 routing打磨 fitting; polishing打磨机 polisher本生灯 Bunsen burner本征半导体 intrinsic semiconductor正反器；触发器；复振器 flip-flop正反馈；正回输 positive feedback正火 normalizing正向偏置 forward bias正投影 orthographic projection正投影图 orthographic drawing正弦波形 sinusoidal waveform正面投影 front projection正视图 elevation; front elevation正极；阳极 anode正齿轮 spur gear正台；平面板 surface plate永久性接合 permanent joining瓦通纸；瓦楞纸板 corrugated board生长层 cambium layer生产图 production drawing生胶浆 rubber cement生钢；铸钢 cast steel生铁；铸铁 cast iron用途；功能 function白杨木 poplar白胶浆 PVA glue; white glue皮沙垫 leather sandbag皮革 leather皮革黏合剂 leather glue皮鞋 leather shoes目录 contents矢量；向量 vector石灰岩 limestone石英晶体振荡器 quartz crystal oscillator 石棉 asbestos; asbestus石膏 Plaster of Paris示波器 oscilloscope立体图 pictorial drawing六画交流电流 alternating current .)交流电压 . voltage交联结构 cross-linked structure仿饰金 gilding metal伏特 volt光力架 clear lacquer光敏电阻 light dependent resistor (LDR)光测弹性学 photoelasticity光刨；滑刨 smoothing plane光电效应 photoelectric effect光泽 lustre全闭式槽榫 closed housing joint共面力 coplanar force共聚合作用 co-polymerization共聚物 copolymer共价键 covalent bond共振；共鸣；谐振 resonance印刷电路板 printed circuit board (PCB)同素异形 allotropy同轴电缆 coaxial cable同温 equality of temperature向量；矢量 vector向量和 vector sum合力 resultant force合口扁钳 close mouth tongs合成色；等和色 secondary colour合成品 composite合成粅料 composite material合金 alloy合金工具钢 alloy tool steel合钉；定位销 dowel回火 tempering回复力 restoring force回复力偶 restoring couple回弹 resilience回输；反馈 feedback地线 earth wire多刃切削刀具 multi-point cutter多孔塑料；泡沫塑料；海绵状塑料 foam plastics 多方榫接合 pinned joint多媒体 multi-media多晶性 polycrystallinity多谐振动器；多谐振荡器 multivibrator多边形力学；力多边形 polygon of force字母冲 letter punch字板 letter stencil安全 safety安全守则 safety rule安全系数 safety factor安全措施 safety precaution安全眼罩 safety goggle安全设备 safety equipment安全药箱 safety box安培 ampere安培计；电流表 ammeter尖脚 spur年轮 annual ring成本 cost成形 forming扣件；击固件 fastener扣钉 clout nail; cramp托架 bracket收缩 shrinkage曲柄 crank曲柄轴 crank shaft曲线规；云板；云尺 French curve有效的 efficient有效电流 effective current灰；灰末 ash百折胶；百折胶；聚丙烯 polypropylene (PP) 竹 bamboo羊角锤 claw hammer老化 ageing肋条 rib肌理；质感；质地 texture自由度 degree of freedom自动控制 automatic control自动进给 auto-feed自然干燥法 natural seasoning自感量 self-inductance自感应 self-induction色彩；颜色 colour色调 tone色环 colour wheel行星齿轮；周转齿轮 epicyclic gear七画肘节开关 toggle-switch串激电动机；串绕电动机 series-wound motor 位能；势能 potential energy位梯度；势梯度 potential gradient位移 displacement位错 dislocation伸长度 elongation作工硬化 work hardening作功 work done作图线 construction line低密聚乙烯 low density polyethylene (LDPE) 低通滤波器 low-pass filter低电压 low voltage低碳钢 low carbon steel布置 layout免油轴承 oil-less bearing冷加工；冷作工 cold working冷加工硬化 cold work hardening冷色 cool colour冷轧压 cold rolling冷却系统 cooling system冷却效应 cooling effect冷却液流量 coolant rate冷凝胶；环氧树脂 epoxy resin利口；「披」口；铁屑 burr刨平 planing刨花板；碎料板 particle board吹风机 air blower吹气模塑；吹模塑 blow moulding吹管 blow pipe含铁金属 ferrous metal含水量 moisture content坑凿 cross-cut chisel均方根值 root mean square value均角投影图；等角投影图 isometric drawing 均速圆周运动 uniform circular motion夹；夹钳 clamp夹 cramp夹卡 mounting board夹具 fixture; jig夹具及固定装置 jig and fixture夹板；胶合板 plywood夹持工具 clamping device; holding tool夹背锯；榫锯 tenon saw夹头 chuck夹头开启匙；夹头扳手 chuck key夹迭黏合成形 lamination尾座 tailstock床身；床道 lathe bed床鞍；刀座帷 apron形心；面心 centroid形状 shape形变 deformation「快把」板；硬质纤维板 hardboard快速移位 rapid traverse抗扭强度 torsional strength抗屈强度 bending strength; yield strength 抗性分量；无功分量 reactive component抗拉强度 tensile strength抗氧化剂 anti-oxidant抗剪强度 shearing strength抗磁性物料 diamagnetic material抗挠性 stiffness抗压强度 compressive strength抗断强度 breaking strength技术员；技师 technician扶架 steady扭力 torsion扭矩；转矩 torque扭转 torsion扭转角 angle of torsion把手 hand grip扼流圈 choke扳手 spanner; wrench投影 projection投影面 projection plane投影线 projection line攻丝 tap材料 material材料单；材料表 material list杜拉铝 duralumin杉木 spruce步进电动机 stepper motor步冲轮廓法 nibbling系统组件 system component角托架 angle bracket角位移 angular displacement角板；直角板 angle plate角度 angle角榫 corner angle joint; corner joint角铁 angle iron谷巴凡立水 cobal varnish车刀架 tool holder车床 lathe车床工具 lathe tools车床中心钻咀 lathe centre bit车床操作法 lathe operation车削；车旋 lathe turning; turning车削工具 turning tools防火胶板 Formica防锈 rust prevention防声耳筒；护耳器 ear-protector防松螺帽 lock nut防护装置；保护罩；保护网 guard; safety guard八画注射成形法；喷射铸造法 injection moulding并激电动机；并绕电动机 shunt-wound motor奶酪胶 casein glue乳胶漆 emulsion paint亚加力；压克力；聚甲基丙烯酸甲脂 acrylics; polymethyl methacrylate (PMMA) 亚稳态的；介稳态的 metastable来回摆动 oscillating两点透视 two-point perspective刻度；划线 ruling刺冲 dot punch刮刀 scraper刮擦 scraping制动鼓 drum brake制动碟 disc brake制动器 brake受迫振动 forced vibration受迫振荡 forced oscillation和谐 harmony周转齿轮；行星齿轮 epicyclic gear固定夹；台夹 bench holdfast固定负载 dead load定子 stator定位销；合钉 dowel定位螺丝 set screw定距轮 stitch marker屈片机 folding machine屈曲 bending屈服点；降服点 yield point屈圈法 loop forming屈卷法 scrolling屈接缝 folded lap seam屈喉机 tube bender屈折 folding屈折线 folding line屈压接缝 folded & grooved seam延性 ductility延性的 ductile弦锯法 plain sawing弧口凿；圆凿 gouge往复式运动 reciprocatory motion拉力 tensile force拉力计；张力计 tensiometer; tensometer拉钉 blind rivet; pop rivet拉钉接合 blind riveting; pop riveting拉钉钳 blind riveting pliers; pop riveting pliers拉张 tension拉张应力 tensile stress拉张应变 tensile strain拉细 drawing-down拉制法 drawing拉线 wire drawing「披」口；利口；铁屑 burr拔钳 nippers抛光 buffing抛光机 buffing machine放大；扩大 enlargement放大尺 pantograph放大倍数 amplification factor放大器 amplifier放电极加工；火花电蚀法 electrical discharge machining 易用万能尺 line setter易碎 fragile〈绘画的〉明暗运用；描影 shading枝；杆 rod杯形顶尖 cup centre杯头螺丝 hexagonal socket head cap screw板锯 panel saw松木 pine松节水 turpentine法式磨光 French polishing法拉〈电容量单位〉 farad油石；磨刀石 oil stone油漆；涂料 paint泡沫塑料；多孔塑料；海绵状塑料 foam plastics物理特性 physical property物理属性 physical attribute物理量 physical quantity盲孔；闭孔；不贯穿孔 blind hole直尺 ruler; straight rule直角叉榫 corner bridle joint直角尺 try square直角板；角板 angle plate直角杠杆 bell crank lever直身钻嘴 straight shank drill直车刀架 straight tool holder直流发电机 . generator直流电流 direct current .)直流电动机；直流马达 . motor 直纹锯 rip saw 直线切削 linear interpolation 直线运动 rectilinear motion 直边凿；方边凿 firmer chisel 直铁剪 straight snips 硅 silicon 空行程 idle stroke 空气动力学 aerodynamics 空间 space 空载 no load 花纹凿 embossing stamp 花梨木 rosewood 花样；图案 pattern 虎克定律Hooke's Law 虎钳 vice 虎钳护罩 vice clamp 初步意念 proposed solution 表面surface 表面展开图 surface development 表面张力 surface tension 表面处理surface finishing; surface treatment 表面硬化 case hardening 表面硬化钢case-hardened steel 表达方式 presentation 表达技巧；传意技巧 communication technique 表观膨胀；视膨胀 apparent expansion 金工 metalwork 金工工作间metalwork area 金工角尺 engineering square 金工车床 metalwork lathe 金工虎钳engineer's vice 金工锯床 power hacksaw 金属包头；金属箍 ferrule 金属配件metal fittings 金属线 wire 金属压展机 hand rolling mill 金属擦光剂；磨光剂metal polish 金属薄片 sheet metal 金属键 metallic bond 长方通 rectangular tube 长刨 trying plane 长螺旋钻咀 long auger bit 长镗孔 long boring 闸极gate 阻抗 impedance 附件 attachment 附录 appendices 青铜 bronze 非反相放大器non-inverting amplifier 非本征半导体 extrinsic semicon。
加工中心英文资料
立式加工中心系列----VMC850选择配置Configuration option三菱、FANUC、西门子等数控系统Mitsubishi、FANUC、Siemens numerical control system圆盘式刀库、斗笠式刀库Rotary Disc Type Tool Magazine, Carousel Type Tool Magazine 自动排屑器Automatic chip remover第四轴rotate worktable硬轨、线轨Hard rail, line rail全封闭防护罩Fully enclosed protecting cover半封闭防护罩Semi-enclosed protecting cover立式加工中心系列----VMC1060选择配置configuration option三菱、FANUC、西门子等数控系统Mitsubishi、FANUC、Siemens numerical control system圆盘式刀库、斗笠式刀库Rotary Disc Type Tool Magazine, Carousel Type Tool Magazine 自动排屑器Automatic chip remover第四轴Rotate worktable硬轨、线轨Hard rail, Line rail全封闭防护罩Fully enclosed protecting cover半封闭防护罩Semi-enclosed protecting cover立式加工中心系列----VMC1370三菱、FANUC、西门子等数控系统Mitsubishi、FANUC、Siemens numerical control system 圆盘式刀库Rotary Disc Type Tool Magazine,自动排屑器Automatic chip remover第四轴Rotate worktable全封闭防护罩Fully enclosed protecting cover半封闭防护罩Semi-enclosed protecting cover立式加工中心系列----VMC1690选择配置三菱、FANUC数控系统Mitsubishi、FANUC numerical control system圆盘式刀库Rotary Disc Type Tool Magazine,自动排屑器Automatic chip remover第四轴rotate worktable全封闭防护罩Fully enclosed protecting cover半封闭防护罩Semi-enclosed protecting cover立式加工中心系列----VMC1890选择配置三菱、FANUC数控系统Mitsubishi、FANUC numerical control system 第四轴rotate worktable圆盘式刀库Rotary Disc Type Tool Magazine自动排屑器Automatic chip remover第四轴rotation worktable全封闭防护罩Fully enclosed protecting cover 半封闭防护罩Semi-enclosed protecting cover龙门系列数控机床选择配置三菱、FANUC数控系统Mitsubishi、FANUC numerical control system第四轴Rotate work table龙门系列Gantry Series平床身数控车床系列---- CK6140 Flat bed NC lathe CK6140CK6140技术参数technical parameters机床重量机床铸件均采用米汉纳铸铁、树脂砂铸件，经过两次时效处理，稳定性好，强度高，各项精度稳定可靠。
加工中心
加工中心中文名称：加工中心英文名称：machining center其他名称：自动换刀数控机床定义：能自动更换工具，对一次装夹的工件进行多工序加工的数控机床。
所属学科：机械工程（一级学科）；切削加工工艺与设备（二级学科）；金属切削机床-各种金属切削机床（三级学科）本内容由全国科学技术名词审定委员会审定公布BVM-100-2D双通道现场动平衡仪的加工中心有个很好的故障诊断及振动测试，谁就能在同行业中抢得了制高点。
现在很多厂家在自己的加工中心出厂前，也会简单得做一些振动测试，但是都不是很专业，手段简单，用的仪器也很不专业。
加工中心的发展史加工中心最初是从数控铣床发展而来的。
第一台加工中心是1958年由美国卡尼-特雷克公司首先研制成功的。
它在数控卧式镗铣床的基础上增加了自动换刀装置，从而实现了工件一次装夹后即可进行铣削、钻削、镗削、铰削和攻丝等多种工序的集中加工。
二十世纪70年代以来，加工中心得到迅速发展，出现了可换主轴箱加工中心，它备有多个可以自动更换的装有刀具的多轴主轴箱，能对工件同时进行多孔加工。
加工中心的分类按加工工序分类加工中心按加工工序分类，可分为镗铣与车铣两大类。
（1）镗铣（2）车铣按控制轴数分类按控制轴数可分为：（1）三轴加工中心（2）四轴加工中心（3）五轴加工中心。
按主轴与工作台相对位置分类(1)卧式加工中心：是指主轴轴线与工作台平行设置的加工中心，主要适用于加工箱体类零件。
卧式加工中心一般具有分度转台或数控转台，可加工工件的各个侧面；也可作多个坐标的联合运动，以便加工复杂的空间曲面。
(2)立式加工中心：是指主轴轴线与工作台垂直设置的加工中心，主要适用于加工板类、盘类、模具及小型壳体类复杂零件。
立式加工中心一般不带转台，仅作顶面加工。
此外，还有带立、卧两个主轴的复合式加工中心，和主轴能调整成卧轴或立轴的立卧可调式加工中心，它们能对工件进行五个面的加工。
(3)万能加工中心(又称多轴联动型加工中心)：是指通过加工主轴轴线与工作台回转轴线的角度可控制联动变化，完成复杂空间曲面加工的加工中心。
最全木工机械概述完整版.doc
1木工机械概述1.1概述木工机械是木材加工机械的简称，是指从原木到加工成木制品的整个过程中所使用的各种机械设备。
根据GB7635-87标准中规定，木工机械分为：1）木工机床：制材、家具制作等加工设备；2）人造板机械：人造板及木质纤维加工设备；3）木材处理机械：木材干燥、防腐等设备。
本课程是为机械类专业学生了解和掌握木材加工设备知识而设置得选修课。
本课程主要介绍木工机械的前两类，即木工机床和人造板机械，分别从中选取几种具有代表性的机床设备为同学们讲解其用途、结构、工作原理等。
（1）木材的特点和用途木材具有重量轻、强重比高、弹性好、耐冲击、纹理色调丰富美观，加工容易等优点，自古至今都被列为重要的原材料。
木材工业由于能源消耗低,污染少,资源有再生性，在国民经济中也占重要地位。
其产品已从原木的初加工品(如电杆、坑木、枕木和各种锯材)发展到成材的再加工品，如建筑构件、家具、车辆、船舶、文体用品、包装容器等；以及木材的再造加工品，即各种人造板、胶合木等，从而使木材工业形成了独立的工业体系。
（2）我国木材工业的发展中国在石器时代已以石为刃,刳木为舟,开始了木材加工的历史。
青铜时代，出现了锯条的雏形；春秋时期相传鲁班发明墨汁、角尺等多种木工工具；秦汉之际,木工工具种类益多,锛、凿相继发明；北魏时的《齐民要术》中对木材的加工和利用均有论述；沿至唐、宋，已采用锯开、气干、拼合、包封等较为复杂的技术制造木柱，并有了提高木结构稳定性的蒸煮和干燥处理方法，以及加楔、留缝技术。
明代家具以其结构精巧、造型简朴驰名中外。
中国木材加工业的逐渐机械化始于清末，这时外商在中国建立机械化制材厂，继而发展地板、门窗等以房屋建筑为对象的木材加工厂；20世纪初又设厂生产胶合板。
到50年代中期，胶合板生产有了发展，接着并开始制造刨花板及纤维板；表面装饰材料及层积材等也陆续出现；实木、板式家具实现机械化、自动化生产。
这标志着中国的木材加工业已进入以综合利用为中心的现代化时期。
加工中心中英对照
5TH AXIS HARDWARE OVERTRAVER LIMIT ERROR
DOOR IS OPENED(开门)
LUB PRESSURE SWITCH ERROR(油压开关错误)
SPINDLE OIL COOLANT UNIT ERROR
SPINDLE LOAD ABNORMAL（主轴负荷异常）
数控机床中英文对照表
ABS和REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标
ALL——全选，程序编辑时用
PRGRM——程序（program）的缩写，用于查看程序
NEXT——查看程序和查看参数时，下一页
OPRT——在法那克系统中，选择编辑程序时，也就是按下PRGRM后，再按这个键，才能输入程序号
ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）
CENTRE LUBRICATION FALL （中心润滑故障）
THE WORK NOT CLAMPED （工件未夹紧）
AUTO TOOL CHANGE FAULT （自动换刀失败）
TOOL DATA OUT OF RANGE （指令刀具号超出范围）
MT NOT READY（机床没准备好）
MG OVERLOAD （刀库过载）
LUB EMPTY（润滑无油）
AIR PRESSURE（气压不足）
COOLANT NOT READY（冷却没准备好）
LUBE EMPTY（油雾油位低，润滑油位低）
LUB PRESSURE LOW（润滑压力低）
TRANSDUCER ALARM（传感器报警）
木工行业英语词汇
S School table 课桌
Screen 屏风 Seat 痤椅 Seating element 痤垫 Secretarial chair 秘书椅 3-section mirror 三面梳妆镜 semi-CKD 半拆装家具 serving table 送餐桌
家具英译（1）——家具种类 A Adjustable bed 可调床 Air bed 气床 Anti-slip strip for stairs （儿童床）防滑楼梯打击扶手 Antique furniture 古式家具 Antique reproduction furniture 仿古家具 Armchair 扶手椅
1
Hutch 碗架
I Institutional furniture 风俗家具，公用家具
J Junior desk chair 学生书桌椅
K Kitchen block /kitchen rock 厨房地砖 Kitchen cabinet 餐具柜 Kitchen chair, stool and bench 厨房椅、圆凳及条椅 Kitchen fitment 厨房固定家具 Kitchen table 厨房餐桌 Kitchen unit 厨房成套家具
M Managerial mediumback chair 中背经理椅 Margined flush door 镶边平板门 Mattress 床垫，席梦思 Mediumback executive chair 中背办公椅 Metal furniture 金属家具 Mirror door 玻璃门 Mirror for chest of drawers 多屉柜梳妆镜 Multi-purpose sofa 多用沙发 Multi-purpose table 多用桌
家具工厂机器设备大全中英文对照
家具工厂机器设施大全1.横切锯 (Cutoff Saw)2.面刨 (Facer)手压刨 (Hand Jointer)3. 刨木机 (Planer)单面刨 (Single Planer)双面刨 (Double Planer)上下刨 (Facer/Planer)4. 刨(修)边设施 (Lumber Edge Jointing Equipment) Glue Joint Edging Saw胶合平刨机 (Glue Jointer)5. 纵切锯 (Rip Saws)直线纵切锯 (Straight-Line Ripsaw)多片锯 (Gang Ripsaw)6. 胶合设施 (Equipment for Edge ＆ Face Gluing)胶合展起色 (Glue Reel，Clamp Carrier)Batch Press连续式拼板机 (Continuous Edge Gluer)7. 合板设施 (Plywood Equipment)薄片裁切机 (Veneer Clippers)薄片拼接机 (Veneer Splicers)布胶机 (Glue Spreaders)热压机 (Hot Presses)8.裁板设施 (Panel Cutting Equipment)Panel Cut-Up SawsPanel Saws for Trimming9.四周刨 (Moulder)传统式四周刨 (Conventional Moulder)模块设计四周刨 (Feed-Through Moulder-Design Moulder)10.双端裁剪机 (Double End Tenoner)11.全能锯 (Variety Saw)12.带锯与再锯机 (Band Saws ＆ Resaws)带锯机 (Bandsaws)自动带锯机 (Auto. Bandsaws)再锯机 (Resaws)13. 铣剖机与靠模成形机 (Shapers ＆ Profilers)单轴铣剖机 (Single-Spindle Shapers)双轴铣剖机 (Double-Spindle Shapers)自动铣剖机及靠模成形机＆Profilers)Linear Feed ProfilerFixed-Spindle Rotary Shapers and ProfilersWhitney-Type ShaperA &B Auto. ShaperRotary-Table Shapers and ProfilersDouble-Spindle Copying Shaper14. 路达机 (Routers)传统型 (Conventional Pin Router)倒立型 (Inverted Router)数控型 (Numerically Controlled Routers)15. 鸠尾榫机 (Dovetail Machines)鸠尾榫机 (Dovetailer)自动鸠尾榫机 (Auto. Dovetailer)法式鸠尾榫机 (French Dovetailer Machines )16. 雕琢机 (Wood Carving Machines)路达机 (Router)单轴雕琢机 (Spindle Carver)多轴雕琢机 (Multiple-Spindle Carver)热压花机 (Embossing Presses)17. 角凿机 (Mortisers)空心角凿机 (Hollow Chisel Mortiser)振荡凿孔机 (Oscillating Chisel Mortiser)路达机 (Router)18. 钻孔机 (Boring Machines)单轴钻孔机 (Single-Spindle Boring Machines)垂直多轴钻孔机 (Verticle Multiple-Spindle Machines)水平双轴钻孔机 (Horizontal Double-Spindle Machine)簇头 (Cluster Heads)钻孔机 (Fixed-Center Boring Machine)非平行钻孔 (Nonpallel Boring)点到点钻孔 (Point-To-Point Boring)床架钻孔作槽机 (Bed Lock Machines)19. 制椅设施 (Equipment for Seating Furniture)圆榫加工刀头 (Chucking Heads)双端横切及钻孔机 (Double-End Trim and Boring Machine)单端横切及圆榫机 (Single-End Cutoff Boring or Chucking Machine)双端横切、钻孔、注胶及插木钉机(Feed_Through Trim and B ore Machine)水平锯 (Leveling Saw)鞍座刨 (Saddle Seat Cutting)椅座钻孔机 (Seat Boring Machines)椅后脚多轴钻孔机 (Back Post Multiple Boring Machine)20. 车床 (Wood Turning Lathes)单点车床 (Single-Point Lathes)背刀车床 (Back-Knife Lathes)形削车床 (Shaping Lathes)仿形车床 (Copying Lathes)21. 平面砂光机 (Flat Sanding)宽带砂光机 (Wide-Belt Sanders)多鼓砂光机 (Multiple-Drum Sanders)砂刨机 (Abrasive Planers)Hand BlockSanders Hand Lever Stroke SanderPower Stroke SanderHand -Fed SandersSemi-Automatic Sanders Automatic SandersCross-Belt/Wide-Belt Combination Polisher22.曲面砂光机 (Sanding Edges ＆ Mouldings)Edge SanderVertical Belt Variety SanderScroll SanderMould SandingHand Block SandingStationary Formed-Block SandingAutomated_Feed Moulding Sanders for PanelEdges Pneumatic-Drum SandersSpool and Wrap SandersRotating Abrasive Brushes and Wheels Sandind Carvings Sanding TurningsCopy-Shape SandingReciprocating Sanding of Mouldings23. 装置设施 (Assembly Equipment)胶枪 (Glue Gun)布胶器 (Spreaders)木钉涂胶插入机 (Dowel Gluing and Driving Machine)夹具 (Clamps)平面夹具 (Clamps for Flat Subassemblies)高周波夹具 (High-Frequency Electric Assembly Fixtures)立体装置夹具 (Clamps for Final Assembly)旋动箱体夹具 (Revolving Case Clamp)旋动箱体夹具 (Stationary Case Clamping Machine)椅子夹具 (Chair Clamp)抽屉夹具 (Drawer Clamp)床与镜框夹具 (Bed or Mirror Frame Clamp)打钉机 (Fastening Machines)转自 :[url= ://bbs.wtoqc /?fromuid=0] 验货员论坛 [/url]。
机械加工介绍(中英文对照)
机械加工介绍（中英文对照）1 LathesLathes are machine tools designed primarily to do turning, facing and boring, Very little turning is done on other types of machine tools, and none can do it with equal facility. Because lathes also can do drilling and reaming, their versatility permits several operations to be done with a single setup of the work piece. Consequently, more lathes of various types are used in manufacturing than any other machine tool.The essential components of a lathe are the bed, headstock assembly, tailstock assembly, and the leads crew and feed rod.The bed is the backbone of a lathe. It usually is made of well normalized or aged gray or nodular cast iron and provides s heavy, rigid frame on which all the other basic components are mounted. Two sets of parallel, longitudinal ways, inner and outer, are contained on the bed, usually on the upper side. Some makers use an inverted V-shape for all four ways, whereas others utilize one inverted V and one flat way in one or both sets, They are precision-machined to assure accuracy of alignment. On most modern lathes the way are surface-hardened to resist wear and abrasion, but precaution should be taken in operating a lathe to assure that the ways are not damaged. Any inaccuracy in them usually means that the accuracy of the entire lathe is destroyed.The headstock is mounted in a foxed position on the inner ways, usually at the left end of the bed. It provides a powered means of rotating the word at various speeds . Essentially, it consists of a hollow spindle, mounted in accurate bearings, and a set of transmission gears-similar to a truck transmission—through which the spindle can be rotated at a number of speeds. Most lathes provide from 8 to 18 speeds, usually in a geometric ratio, and on modern lathes all the speeds can be obtained merely by moving from two to four levers. An increasing trend is to provide a continuously variable speed range through electrical or mechanical drives.Because the accuracy of a lathe is greatly dependent on the spindle, it is of heavy construction and mounted in heavy bearings, usually preloaded tapered roller or ball types. The spindle has a hole extending through its length, through whichlong bar stock can be fed. The size of maximum size of bar stock that can be machined when the material must be fed through spindle.The tailsticd assembly consists, essentially, of three parts. A lower casting fits on the inner ways of the bed and can slide longitudinally thereon, with a means for clamping the entire assembly in any desired location, An upper casting fits on the lower one and can be moved transversely upon it, on some type of keyed ways, to permit aligning the assembly is the tailstock quill. This is a hollow steel cylinder, usually about 51 to 76mm(2to 3 inches) in diameter, that can be moved several inches longitudinally in and out of the upper casting by means of a hand wheel and screw.The size of a lathe is designated by two dimensions. The first is known as the swing. This is the maximum diameter of work that can be rotated on a lathe. It is approximately twice the distance between the line connecting the lathe centers and the nearest point on the ways, The second size dimension is the maximum distance between centers. The swing thus indicates the maximum work piece diameter that can be turned in the lathe, while the distance between centers indicates the maximum length of work piece that can be mounted between centers.Engine lathes are the type most frequently used in manufacturing. They are heavy-duty machine tools with all the components described previously and have power drive for all tool movements except on the compound rest. They commonly range in size from 305 to 610 mm(12 to 24 inches)swing and from 610 to 1219 mm(24 to 48 inches) center distances, but swings up to 1270 mm(50 inches) and center distances up to 3658mm(12 feet) are not uncommon. Most have chip pans and a built-in coolant circulating system. Smaller engine lathes-with swings usually not over 330 mm (13 inches ) –also are available in bench type, designed for the bed to be mounted on a bench on a bench or cabinet.Although engine lathes are versatile and very useful, because of the time required for changing and setting tools and for making measurements on the work piece, thy are not suitable for quantity production. Often the actual chip-production tine is less than 30% of the total cycle time. In addition, a skilled machinist is required for all the operations, and such persons are costly and often in short supply. However, much of the operator’s t ime is consumed by simple, repetitious adjustments and inwatching chips being made. Consequently, to reduce or eliminate the amount of skilled labor that is required, turret lathes, screw machines, and other types of semiautomatic and automatic lathes have been highly developed and are widely used in manufacturing.2 Numerical ControlOne of the most fundamental concepts in the area of advanced manufacturing technologies is numerical control (NC). Prior to the advent of NC, all machine tools ere manually operated and controlled. Among the many limitations associated with manual control machine tools, perhaps none is more prominent than the limitation of operator skills. With manual control, the quality of the product is directly related to and limited to the skills of the operator. Numerical control represents the first major step away from human control of machine tools.Numerical control means the control of machine tools and other manufacturing systems through the use of prerecorded, written symbolic instructions. Rather than operating a machine tool, an NC technician writes a program that issues operational instructions to the machine tool. For a machine tool to be numerically controlled, it must be interfaced with a device for accepting and decoding the programmed instructions, known as a reader.Numerical control was developed t o overcome the limitation of human operators, and it has done so. Numerical control machines are more accurate than manually operated machines, they can produce parts more uniformly, they are faster, and the long-run tooling costs are lower. The development of NC led to the development of several other innovations in manufacturing technology:Electrical discharge machining,Laser cutting,Electron beam welding.Numerical control has also made machine tools more versatile than their manually operated predecessors. An NC machine tool can automatically produce a wide of parts, each involving an assortment of widely varied and complex machining processes. Numerical control has allowed manufacturers to undertake the production of products that would not have been feasible from an economic perspective using manually controlled machine tolls and processes.Like so many advanced technologies, NC was born in the laboratories of the Massachusetts Institute of Technology. The concept of NC was developed in the early 1950s with funding provided by the U.S. Air Force. In its earliest stages, NC machines were able to made straight cuts efficiently and effectively.However, curved paths were a problem because the machine tool had to be programmed to undertake a series of horizontal and vertical steps to produce a curve. The shorter the straight lines making up the steps, the smoother is the curve, Each line segment in the steps had to be calculated.This problem led to the development in 1959 of the Automatically Programmed Tools (APT) language. This is a special programming language for NC that uses statements similar to English language to define the part geometry, describe the cutting tool configuration, and specify the necessary motions. The development of the APT language was a major step forward in the fur ther development from those used today. The machines had hardwired logic circuits. The instructional programs were written on punched paper, which was later to be replaced by magnetic plastic tape. A tape reader was used to interpret the instructions written on the tape for the machine. Together, all of this represented a giant step forward in the control of machine tools. However, there were a number of problems with NC at this point in its development.A major problem was the fragility of the punched paper tape medium. It was common for the paper tape containing the programmed instructions to break or tear during a machining process. This problem was exacerbated by the fact that each successive time a part was produced on a machine tool, the paper tape carrying the programmed instructions had to be rerun through the reader. If it was necessary to produce 100 copies of a given part, it was also necessary to run the paper tape through the reader 100 separate tines. Fragile paper tapes simply could not withstand the rigors of a shop floor environment and this kind of repeated use.This led to the development of a special magnetic plastic tape. Whereas the paper carried the programmed instructions as a series of holes punched in the tape, the plastic tape carried the instructions as a series of magnetic dots. The plastic tape was much stronger than the paper tape, which solved the problem of frequent tearing and breakage. However, it still left two other problems.The most important of these was that it was difficult or impossible to change the instructions entered on the tape. To made even the most minor adjustments in a program of instructions, it was necessary to interrupt machining operations and make a new tape. It was also still necessary to run the tape through the reader as many times as there were parts to be produced. Fortunately, computer technology became a reality and soon solved the problems of NC associated with punched paper and plastic tape.The development of a concept known as direct numerical control (DNC) solved the paper and plastic tape problems associated with numerical control by simply eliminating tape as the medium for carrying the programmed instructions. In direct numerical control, machine tools are tied, via a data transmission link, to a host computer. Programs for operating the machine tools are stored in the host computer and fed to the machine tool an needed via the data transmission linkage. Direct numerical control represented a major step forward over punched tape and plastic tape. However, it is subject to the same limitations as all technologies that depend on a host computer. When the host computer goes down, the machine tools also experience downtime. This problem led to the development of computer numerical control.3 TurningThe engine lathe, one of the oldest metal removal machines, has a number of useful and highly desirable attributes. Today these lathes are used primarily in small shops where smaller quantities rather than large production runs are encountered.The engine lathe has been replaced in today’s production shops by a wide variety of automatic lathes such as automatic of single-point tooling for maximum metal removal, and the use of form tools for finish on a par with the fastest processing equipment on the scene today.Tolerances for the engine lathe depend primarily on the skill of the operator. The design engineer must be careful in using tolerances of an experimental part that has been produced on the engine lathe by a skilled operator. In redesigning an experimental part for production, economical tolerances should be used.Turret Lathes Production machining equipment must be evaluated now, more than ever before, this criterion for establishing the production qualification of a specific method, the turret lathe merits a high rating.In designing for low quantities such as 100 or 200 parts, it is most economical to use the turret lathe. In achieving the optimum tolerances possible on the turrets lathe, the designer should strive for a minimum of operations.Automatic Screw Machines Generally, automatic screw machines fall into several categories; single-spindle automatics, multiple-spindle automatics and automatic chucking machines. Originally designed for rapid, automatic production of screws and similar threaded parts, the automatic screw machine has long since exceeded the confines of this narrow field, and today plays a vital role in the mass production of a variety of precision parts. Quantities play an important part in the economy of the parts machined on the automatic screw machine. Quantities less than on the automatic screw machine. The cost of the parts machined can be reduced if the minimum economical lot size is calculated and the proper machine is selected for these quantities.Automatic Tracer Lathes Since surface roughness depends greatly on material turned, tooling , and feeds and speeds employed, minimum tolerances that can be held on automatic tracer lathes are not necessarily the most economical tolerances.In some cases, tolerances of 0.05mm are held in continuous production using but one cut . groove width can be held to 0.125mm on some parts. Bores and single-point finishes can be held to 0.0125mm. On high-production runs where maximum output is desirable, a minimum tolerance of 0.125mm is economical on both diameter and length of turn.中文译文1.车床车床主要是为了进行车外圆、车端面和镗孔等项工作而设计的机床。
机床的介绍作文英文翻译
机床的介绍作文英文翻译英文：Introduction to Machine Tool。
Machine tools are essential equipment in the manufacturing industry, as they are used to shape and form metal and other solid materials. These tools include lathes, milling machines, drilling machines, and grinding machines, among others. They play a crucial role in producing a wide range of products, from automotive parts to household appliances.One of the most common types of machine tools is the lathe. It is used to rotate a workpiece against a cutting tool to remove material and create a symmetrical object.For example, when I was working in a metalworking factory,I used a lathe to create precise cylindrical shapes for engine parts. The process involved carefully setting the cutting tool and adjusting the speed and feed to achievethe desired dimensions.Another important machine tool is the milling machine, which uses rotary cutters to remove material from a workpiece. I remember using a milling machine to produce intricate patterns on metal components for aerospace applications. It required a high level of precision and attention to detail to ensure the final product met the strict quality standards.Drilling machines are also widely used in the manufacturing industry to create holes in metal and other materials. When I worked in a fabrication shop, I used a drilling machine to accurately drill holes in steel beams for construction projects. The machine's ability to maintain perpendicularity and concentricity was crucial for ensuring the structural integrity of the final assembly.In addition to these examples, there are many other types of machine tools that serve specific purposes in the manufacturing process. Each tool requires skilled operators to set up and operate, as well as regular maintenance toensure optimal performance.Machine tools have revolutionized the way we produce goods, allowing for greater precision, efficiency, and consistency in manufacturing. They have become an indispensable part of modern industry, and their continued development and innovation will shape the future of manufacturing.中文：机床介绍。
加工中心介绍
∙加工中心介绍∙加工中心(Machining Center)简称MC，是由机械设备与数控系统组成的使用于加工复杂形状工件的高效率自动化机床。
加工中心又叫电脑锣。
加工中心备有刀库，具有自动换刀功能，对工件一次装夹后进行多工序加工的数控机床。
加工中心是高度机电一体化的产品，工件装夹后，数控系统能控制机床按不同工序自动选择、更换刀具，自动对刀、自动改变主轴转速、进给量等，可连续完成钻、镗、铣、铰、攻丝等多种工序。
因而大大减少了工件装夹时间，测量和机床调整等辅助工序时间，对加工形状比较复杂，精度要求较高，品种更换频繁的零件具有良好的经济效果。
加工中心的由来加工中心最初是从数控铣床发展而来的。
与数控铣床相同的是，加工中心同样是由计算机数控系统(CNC)、伺服系统、机械本体、液压系统等各部分组成。
但加工中心又不等同于数控铣床，加工中心与数控铣床的最大区别在于加工中心具有自动交换刀具的功能，通过在刀库安装不同用途的刀具，可在一次装夹中通过自动换刀装置改变主轴上的加工刀具，实现钻、镗、铰、攻螺纹、切槽等多种加工功能。
加工中心的分类一、加工中心按加工工序可分分镗铣与车铣两大类。
（1）镗铣（2）车铣二、按控制轴数可分为：（1）三轴加工中心（2）四轴加工中心（3）五轴加工中心。
三、以主轴与工作台相对位置分类，分为卧式、立式和万能加工中心。
(1)卧式加工中心：是指主轴轴线与工作台平行设置的加工中心，主要适用于加工箱体类零件。
(2)立式加工中心：（Vertical Machining Center）是指主轴轴线与工作台垂直设置的加工中心，主要适用于加工板类、盘类、模具及小型壳体类复杂零件。
(3)万能加工中心(又称多轴联动型加工中心)：是指通过加工主轴轴线与工作台回转轴线的角度可控制联动变化，完成复杂空间曲面加工的加工中心。
适用于具有复杂空间曲面的叶轮转子、模具、刃具等工件的加工。
多工序集中加工的形式扩展到了其他类型数控机床，例如车削中心，它是在数控车床上配置多个自动换刀装置，能控制三个以上的坐标，除车削外，主轴可以停转或分度，而由刀具旋转进行铣削、钻削、铰孔和攻丝等工序，适于加工复杂的旋转体零件。
加工中心介绍范文
加工中心介绍范文加工中心（Machining Center）是一种现代化的机床设备，广泛应用于各个制造业领域，主要用于加工复杂形状的零件。
加工中心集铣削、钻削、镗削、攻丝等多种加工功能于一体，能够在同一台机床上完成多道加工工序，大大提高了生产效率和产品精度。
加工中心由数控系统、机械结构、自动换刀系统等部分组成。
数控系统控制着机床的各种动作，并通过编程实现零件的加工。
机械结构是加工中心实现各种加工功能的关键部件，包括主轴、滑台、工作台等。
自动换刀系统可以根据不同的加工需求，自动更换不同的刀具，实现多道加工工序的连续加工。
加工中心具有以下的优点：1.高加工精度：加工中心采用数控系统控制各种动作，可以实现高精度的加工，确保零件的尺寸和表面质量。
2.高生产效率：加工中心的自动换刀系统可以实现多道工序的连续加工，避免了人工换刀的时间浪费，大大提高了生产效率。
3.复杂零件加工能力强：加工中心可以通过数控编程实现复杂形状零件的加工，包括曲线、曲面等形状，能够满足现代制造业对复杂零件加工的需求。
4.灵活性强：加工中心可以根据不同的加工要求进行编程调整，达到灵活生产的目的。
同时，加工中心还可以通过加装夹具等辅助装置，实现各种特殊形状零件的加工。
5.自动化程度高：加工中心可以实现自动化控制和连续加工，减少了人工操作的繁琐过程，降低了人为因素对产品质量的影响。
加工中心的应用范围非常广泛，包括机械制造、航空航天、汽车制造、电子电器等各个制造业领域。
在机械制造领域，加工中心可以用于加工各种金属材料和非金属材料的零件，包括铝合金、钢材、铜材、塑料等。
在航空航天领域，加工中心可以用于加工飞机零部件，包括航空铝合金件、复合材料件等。
在汽车制造领域，加工中心可以用于加工汽车发动机零部件、车身结构件等。
在电子电器领域，加工中心可以用于加工电子器件和外壳等。
总之，加工中心是现代制造业中不可或缺的重要设备之一，它能够满足高精度、高效率、多功能的加工需求，提高产品质量和生产效率。
木工机械行业专业英语词汇表
木工机械行业专业英语词汇表木工机械行业专业英语词汇表锯机 sawing machine框锯 frxxxxame saw带锯 band saw圆锯 circular saw摆锯 swing saw裁边锯edger又称“齐边机”。
截头锯 trimmer主锯 head saw headrig开槽锯 grooving saw万能圆锯 radial-arm saw钢丝锯 fret saw狐尾锯 drag saw原木跑车 log carriage削片-锯解联合机 chipping headrig削边机 chipping edger接锯机 brazer磨锯机saw sharpenerautomatic band saw sharpener 带锯自动锉锯机automatic circular saw sharpener 自动锉（圆）锯机automatic controlled machine 自控机床automatic copy shaper 自动仿型刨边机（单刀）automatic copy shape 自动仿型刨边机（双轴）（附安全门）automatic feeder for veneer dryer 单板干燥机的自动填料机automatic hydraulic backnife wooden lathe 全自动液压背刀式木工车床automatic loader and unloader 自动装卸机automatic rotary table shaper 自动转台式成型机automatic sponge drum sander 自动鼓式海绵砂光机automatic strake belt sander 自动带式砂光机automatic stroke belt sander 自动（抚摸）砂光机automatic tapping and screwing machine 自动攻牙锁螺丝机automatic turning sander 全自动砂光机，自动圆棒砂光机automatic wide-belt sander 宽带砂光机BBack and arm impact test machine 椅背扶手冲击试验机balance cut-off saw 平衡截断锯Band and circular saw sharpener 带锯圆面积锯两用锉锯机Band resaw 再分带锯机Band saw 带锯Band saw clamp 带锯夹Band saw machine 带锯机Band saw machine with auto-feed carriage 带锯机附自动填料传送车Band saw machine with hand-feed carriage 带锯机附手扒送料车Band saw sharpener 带锯磨锯机Band saw shear 带锯剪（截）机Band saw slasher多带横切锯Band saw stretcher 带锯滚压机Band saw welding clamp接锯机Band sawing 带锯制材Band scroll saw 细木工带锯，曲线带锯Barefaced tenon 裸面榫Bark-peeler 剥皮机Barking drum 鼓式剥皮机Barking machine 剥皮机Belt conveyor 带式传送器Belt drier 带式干燥机Belt drive 皮带传动Belt grinder 带式磨床Belt sander 带式砂光机Bentwood forming machinery曲木成型机Bevel saw 斜面锯Bifurcated rivet 开叉钉Bit 齿片，钻头Blade 锯条Block plane 短刨Blower通风机，鼓风机Blower kiln 鼓风式干燥窑Bobbin sander 轴式砂光机Body press （家具）装配压床Boring machine 钻床Bow saw 弓锯Brash chopper 枝梢切断机Breathing veneer drier 呼吸式单板干燥机Buffing machine 抛光机Business item 产品Butting saw 截锯，齐头锯CCabinet whole-plant equipment 橱柜整厂设备Carbide tool grinder 炭素钢刀具研磨机Carving machine 雕刻机Centerless sander 圆棒砂光机Centrifugal blower 离心通风机Chain-belt conveyer veneer drier 网带式单项式板干燥机Chain mortiser 插床Chain saw 链锯Chain saw machine 链锯机Chair aim static load test machine 椅扶手静荷试验机Chair back and arm impact test machine 椅背扶手冲击试验机Chair back static load test machine 座椅靠背静荷试验机Chair leg static load test machine椅腿静荷试验机Chair stability test machine座椅靠背耐久性试验机Chair whole-plant equipment 椅子整厂设备Chip board press 碎木板压合机Chip edger 双削齐边锯Chromometer 比色机Circular gang-saw 圆排锯Circular saw bench 简单圆面积锯机Circular saw bench for band feed ripping 手工送料纵切圆锯机Circular-saw sharpener 圆锯锉锯机Coating adhesion test instrument 漆膜附着力试验仪Coating impact instrument 漆膜冲击仪Coating surface impact instrument漆膜表面冲击仪Concave plane 凹底刨Concave saw 凹面（圆）锯Conveyor输送机Copier 复印机Corner locking machine 锁角机Cross cut band saw machine 横切带锯Cup type wheel stone机碗形砂轮Cup wheel杯形砂轮Curtain flow coater 淋幕式平面涂装机Custom 订做Customized solutions 订做胶水Cut-to –size saw 裁板锯Cutting block组合铣刀Cutting head 刀座，刀头Cutting jip 切削夹具Cylinder saw 桶形锯，圆桶锯Cylindircal saw 圆桶锯DDado head 组合刀头Debarder 剥皮机Deck planer大型电刨Decorative tip 装饰物Disc and spindle sander 盘式轴式联合砂光设备Disc planer 圆盘刨Disc sander 圆盘砂光机Door whole-plant equipment 门斗整厂设备Double band saw 双边带锯Double belt sander 双边砂光机Double bevel cutter 双斜刨刀Double-edge cutting band saw 双边齿带锯Double-side planer双面刨木机double spindle shaper 双轴铣床Double surface oscillatingcurve sander 双面震动曲型杪光机Double surface planer双面刨Double surfacer 双（面）压刨Double-swage(set)saw 双压料锯Double thicknesser 双（面）压刨Dovetail machine 鸠尾榫机Dowel making machine暗榫（加工）机Drag saw sharpener狐尾机，锉锯机Drawer durability test machine 抽屉耐久性试验机Dresser 砂轮修整器，砂轮刀Drop test machine 跌落试验机Drum barker 滚筒剥皮机Drum sander 滚筒砂光机Drunken saw 摇摆（圆）锯Dust cleaner conveyor 粉尘清除输送机Dust collector 集尘器。
数控加工中常见设备的中英文对照
nc milling 数控铣床nc turning 数控车床nc grinding 数控磨穿turning center 车削中心（1）：按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Boring heads 搪孔头Boring machines 镗床Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,steel 铸钢Chamfer machines 倒角机Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Coolers 冷却机Cutters 刀具Diamond cutters 钻石刀具Die casting dies 压铸冲模Die casting machines 压铸机Disposable toolholder bits 舍弃式刀头Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Fixture 夹具Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines,centerless 无心精研机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式及卧式铣床Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Planing machines 刨床Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Slotting machines 插床spindles 主轴Tapping machines 攻螺丝机Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器（2）按中文拼音字母排序铝轮冒口切断机Overflow cutting machines for aluminium wheels 离心压力机Presses,eccentric六角立式铣床Milling machines,turret vertical六角车床Lathes,turret螺栓,螺帽及螺丝Bolts,screws & nuts螺纹磨床Grinders,thread冷却机Coolers冷锻Forging,cold冷锻冲压机Presses,cold forging立式双柱加工中心Machining centers,vertical double-column type立式铣床Milling machines,vertical立式油压拉床Vertical hydraulic broaching machine立式刨床Planing machines vertical立式车床Lathes,vertical立式带锯Saws,vertical band立式加工中心Machining centers,vertical立式及卧式铣床Milling machines,vertical & horizontal立式钻床Drilling machines,vertical联轴器Coupling连续溶解保温炉Aluminum continuous melting & holding furnaces 连续冲模Dies-progressive链传动Chain drive切断机Cutting-off machinesCNC刀杆CNC toolings曲柄压力机presses,crank修整机Finishing machines舍弃式刀头Disposable toolholder bits润滑系统Lubrication Systems润滑液Lubricants熔热处理炉Heating treatment funaces三爪、分割工具头3-Jaws indexing spacers 伺服冲床Presses,servo输送链Conveying chains手工具Hand tools砂轮修整器Wheel dressers蚀刻机Etching machines外圆磨床Grinding machines,cylindrical搪磨机Honing machines搪孔头Boring heads卧式铣床Milling machines,horizontal卧式带锯Saws,horizontal band卧式加工中心Machining centers,horizontal卧式及立式加工中心Machining centers,horizontal & vertical万能铣床Milling machines,universal万能磨床Grinding machines,universal镗床Boring machines弯曲机Bending machines弯管机Tube bending machines通用加工中心Machining centers,general铜锻Forging,copper铣头Milling heads铣床Milling machines无心磨床Grinding machines,centerless无心精研机Lapping machines,centerless压模Pressing dies压铸冲模Die casting dies压铸机Die casting machines油冷却器Oil coolers造链机Chain making tools造线机Cable making tools造钉机Nail making machines印刷电器板油压冲孔脱料系统PCB fine piecing systems摇臂钻床Drilling machines,radial硬(软)板(片)材及自由发泡板机组Hard/soft and free expansion sheet making plant辗压机Rolling machines液压元件Hydraulic components液压冲床Presses,hydraulic液压动力元件Hydraulic power units液压工具Hydraulic power tools液压回转缸Hydraulic rotary cylindersP型PVC高分子防水P type PVC waterproof rolled sheet making plant刨床Planing machines牛头刨床Shapers其他铸造Casting,other其他锻造Forging,other模芯Mold core模具Molds模具维修Mold repair模具打磨/磨纹Mold polishing/texturing模具单元Mold & die components模具加热器/冷却器Mold heaters/chillers磨轮Grinding wheels磨削工具Grinding tools磨床Grinding machines磨床工作台Grinder bench平衡设备Balancing equipment气油压虎钳Pneumatic hydraulic clamps 气动冲床Presses,pneumatic气动工具Pneumatic power tools轴shafts轴承Bearings轴承配件Bearing fittings轴承加工机Bearing processing equipment 肘杆式压力机Presses,knuckle joint铸铝Casting,aluminium铸铜Casting,copper铸造设备Foundry equipment铸钢Casting,steel铸灰口铁Casting,gray iron织麦激光切割机Woven-Cutting machines 重力铸造机Gravity casting machines重型车床Lathes,heavy-duty主轴spindles扳手Wrenches拔丝机Drawing machines保温炉Heat preserving furnaces插床Slotting machines齿轮Gears齿轮切削机Gear cutting machines冲压机Stamping parts冲子研磨器Punch formers超声波打磨机Grinders,ultrasonic车床工作台Lathe bench磁性工具Magnetic tools传动链Transmitted chains床身式铣床Milling machines,bed type带传动Belt drive带锯Saws,band带锯床Sawing machines,band电脑数控镗床CNC boring machines电脑数控弯折机CNC bending presses电脑数控铣床CNC milling machines电脑数控线切削机CNC wire-cutting machines电脑数控磨床CNC grinding machines电脑数控车床CNC lathes电脑数控电火花线切削机CNC EDM wire-cutting machines 电脑数控电火花机CNC electric discharge machines电脑数控雕刻机CNC engraving machines电脑数控机床配件CNC machine tool fittings电脑数控剪切机CNC shearing machines电脑数控钻床CNC drilling machines电动刀具Electric power tools电火花机Electric discharge machines(EDM)雕刻机Engraving machines刀片Blades刀具Cutters倒角机Chamfer machines多轴钻床Drilling machines,multi-spindle锻铝Forging,aluminium锻压机Presses,forging锻模Forging dies仿形铣床Milling machines,duplicating粉末冶金成型机Powder metallurgic forming machines反射炉Reverberatory furnaces钢锻Forging,steel高速车床Lathes,high-speed高速钻床Drilling machines,high-speed管筒制造机Pipe & tube making machines滚筒Rollers工具磨床Grinders,tools & cutters攻螺丝机Tapping machines弓锯Saws,hack虎钳Vises换模系统Mold changing systems夹盘Chucks夹具Fixture夹具/支持系统Clamping/holding systems剪切机Shearing machines加工中心机刀库A.T.C.system激光切割Laser cutting激光雕刻机Engraving machines,laser激光钢板切割机Laser cutting for SMT stensil 集合管Manifolds矫直机Straightening machines金属板成型机Sheet metal forming machines 金属板加工机Sheet metal working machines 锯片Blades,saw锯床Sawing machines卷边工具Crimping tools晶圆切割机Dicing saws精密平口钳Vises,tool-maker精研机Lapping machines可锻铸铁Casting,malleable iron快速换模系统Quick mold change systems 卡口Bayonet开关及按钮Switches & buttons钻石刀具Diamond cutters钻头drills钻模Jigs钻床Drilling machines钻床工作台Drilling machines bench自动压力机Presses,transfer 自动车床Lathes,automatic注油机Lubricators转台Rotary tables。
加工中心tan编
加工中心tan编加工中心是一种现代化的机械设备，它在工业生产中起着重要的作用。
加工中心的英文缩写为CNC，它是Computer Numerical Control的缩写，意为计算机数控。
加工中心的主要功能是用来加工各种金属和非金属材料，可以进行切削、钻孔、铣削等多种加工操作，具有高效、精确的特点。
加工中心的工作原理是通过计算机控制系统，根据预先编好的程序，控制机械设备的运动，实现对工件的加工。
计算机控制系统可以精确控制机床的运动轨迹、转速和切削参数，保证加工的精度和质量。
加工中心的应用领域非常广泛。
在汽车制造业中，加工中心可以用来加工发动机零部件、车身零部件等；在航空航天领域，加工中心可以用来加工飞机零部件、导弹零部件等；在电子通讯领域，加工中心可以用来加工手机壳、电路板等。
加工中心的广泛应用使得各行各业的生产效率得到了极大的提高。
加工中心的优点主要体现在以下几个方面。
首先，加工中心具有高效的加工能力，可以同时进行多种加工操作，大大提高了生产效率。
其次，加工中心具有高精度的加工能力，可以保证加工件的尺寸精度和表面质量。
再次，加工中心具有灵活的加工能力，可以根据不同的加工要求进行编程和调整，适应各种复杂的加工需求。
最后，加工中心具有自动化的加工能力，可以实现自动上下料、自动换刀等功能，减少了人力成本和劳动强度。
然而，加工中心也存在一些不足之处。
首先，加工中心的设备和维护成本较高，需要有一定的投资才能购买和维护。
其次，加工中心的操作和编程相对复杂，需要专业的技术人员进行操作和维护。
再次，加工中心对材料的要求较高，只能加工一些硬度较高的材料，对于一些软材料的加工效果不理想。
为了提高加工中心的使用效果，我们可以采取一些措施。
首先，要加强对加工中心操作和编程技术人员的培训，提高他们的技术水平和操作能力。
其次，要加强对加工中心设备的维护和保养，延长设备的使用寿命。
再次，要加强对加工中心加工工艺的研究和改进，提高加工的精度和效率。
机床的介绍作文英文
机床的介绍作文英文英文：Introduction to Machine Tools。
As a mechanical engineer, I have had the opportunity to work with a variety of machine tools. Machine tools are devices that are used to shape, cut, drill, and finish materials such as metal, wood, and plastic. They are essential in the manufacturing industry and are used to produce a wide range of products, from small parts to large machines.There are many types of machine tools, each with its own specific function. Some of the most common machinetools include lathes, milling machines, drilling machines, and grinding machines. Lathes are used to createcylindrical shapes, while milling machines are used to remove material from a workpiece. Drilling machines are used to create holes, and grinding machines are used tosmooth and finish surfaces.One of the most important aspects of machine tools is their precision. Machine tools must be able to produce parts that meet tight tolerances and specifications. This requires careful calibration and maintenance of the machines, as well as skilled operators who can use the machines effectively.Machine tools have revolutionized the manufacturing industry, allowing for faster and more efficient production of goods. For example, the use of computer numericalcontrol (CNC) machines has greatly increased the speed and accuracy of machining processes. CNC machines use computer programs to control the movement of the cutting tool, resulting in precise and consistent cuts.In conclusion, machine tools are an essential part of the manufacturing industry. They allow for the production of a wide range of products and require skilled operators to use them effectively. The precision and efficiency of machine tools have greatly improved over the years, andthey continue to play a vital role in the manufacturing process.中文：机床介绍。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
圆盘式自动换刀加工中心Disk Auto-tool Changer CNC Machine Center型号：CC-MS1325ADModel: CC-MS1325AD性能特点FEATURES:1. 床体钢结构后壁方管焊接，经振动时效处理，坚固耐用，不易变形。
2. Z轴采用德国滚珠丝杆，台湾高精度30方轨，精度高更耐用。
X.Y轴采用齿条传动，速度更快，更好的提高效率，节省成本。
3.软件兼容性强，可兼容type3/artcam/castmate/文泰等多种CAD/CAM设计制作软件，具有刀具补偿、中文显示、后台编辑、主轴多点定位、模拟操作显示、故障显示功能。
4.台湾宝元（或者新代）控制系统，操作更简便，斗笠式自动换刀系统，更省时安全。
5.驱动系统采用日本安川伺服电机、驱动器。
功能齐全、性能稳定、可靠性高。
6.意大利HSD自动换刀风冷主轴,精度高寿命长。
自动换刀系统操作安全，节省时间。
晨灿木工加工中心7.手动注油系统，维护、保养更方便。
8.六分区真空吸附吸夹两用台面，加工异形工件更加轻松自如，吸力更强，可达250立方/小时。
9.拥有断点续雕、断点恢复、加工时间预测等功能。
10.软件预处理功能可以纠正软件中的错误，而且和各种国际上用的软件代码有兼容性，比如MASTERCAM, TYPE3 和ARTCAM。
3D空间曲线预算法可以保证多线的均匀度，以及曲线的速度和精度.FEATURES:1.Whole machine is welded with seamless steel structure; the stability is excellent, not easy to bedeformed.2.Z axis adopts Germany-made ball-screw and Taiwan made H30 linear orbit, with high precisionand long lifetime. X and Y axes adopt rack and pinion transmission, faster working, higher efficiency and low cost.3. Excellent compatibility: CAD/DAM designing software e.g. Type3/Artcam/Castmate/Wentai etc.4. Adopting Taiwan-made Baoyua（LNC）control system, separate keyboard controlsystem and color LCD screen makes the machine have perfect performance.5. Adopting high-torque Japan-made YASKAMA servo motor and driver, with steady working capability and high positioning precision.6. Adopting Italy-made HSD air-cooling spindle make the machine have high precision, long life-time and steady working capacity. Auto-tool changer system makes the machine safer and save time.7. Auto oil-injection system makes the maintenance more convenient.8. Vacuum table with 6 vacuum zones, which can adsorb different size materials and has strong suction of 23 /hour.9. Has the function of re-carving after break point and power failure. Has the function offorecasting process time.10. Advanced file pretreatment function can correct the error in the files and is compatiblewith the process codes of multiple national and international software.(such asMastercam, Type3,Arecam) .Advance 3D space curve prediction algorithm can make sure of the evenness of polyline and speed and precision of curve lines. 适用材料：Applicable industries:木质加工：加工各种家具如门，窗，橱柜，工艺木门，屏风等广告：雕刻和切割各种铭牌，亚克力水晶字等。
工艺品：在礼物或者纪念品上雕刻各种图形或语言文字Wood processing: processing of various furniture such as door, window, cabinet, craft wooden door, screen and so on.Advertisement: engraving and cutting various labels and number plate.Art craft: engraving characters of any languages and graphics on gifts and souvenirs.适用材料：木材，铝塑板，塑料板，密度板，波浪板，水晶版等广告材料；以及人草软大理石等非金属和轻金属材料。
Applicable materials:Wood, aluminum board, plastic, density board, wave board, PVC, acrylic,crystal, light marble and other nonmetal materials and light metal materials.雕刻效果Processing effect:可以雕刻各种平面雕刻，切割，镂空，铣底，浮雕等各种效果。
Our router may carve various shade vulture, relief and etc. And it can do : Engraving, cutting , milling , drillin g , ect…技术参数Technical specification机器型号Model CC-MS1325-AD Note床体结构Lathe body厚壁方管无缝焊接Thick and Hard Steel structure床身喷砂后烤漆sand blast & seasoning雕刻范围X YZ effective working area1300*2500*300mm台面尺寸Table size 1400*3040mm分辨率Resolution 0.001—0.003 mm主轴功率Spindle power rate 意大利HSD9千瓦Italy made HSD 9.0KW Made In Italy台湾Inverter 台达Delta 台湾TaiwanX,Y轴X,Y structure 齿条传动，台湾30方轨Rack and pinion transmission, Taiwan-madeLinear Bigger orbit, 30mm台湾T aiwanZ轴Z structure 德国滚珠丝杆Germany-made ball screw 德国Germany驱动系统Driver 伺服Servo 日本安川Japan Yaskawa 导轨Guide Rail 上银30方轨Hiwin—30mm 台湾Taiwan主轴转速Spindle rotating speed 0-24000r/min工作电压Standard Power AC380V-/220V-Three Phase (Optional)最大加工速度Max. idling speed 40m/min最大进料高度Max. feeding 300mm冷却方式Cooling mode 风冷Air-cooling雕刻指令Command 标准G代码G code,HPGL,U00,mmg,plt吸尘装置Dust-collect function 有Yes 3.5KW吸尘器3.5KW Dust吸附功能Clamping mode 真空吸附By suction真空泵Vacuum Pump 风冷Air-cooling Germany控制系统Operating system 台湾新代或宝元Taiwan-made Baoyuan system Taiwan刀柄直径Diameter of cutter φ3.175-φ20刀具数量Cutter quantity8把自动换刀刀库Dish-style auto-tool changersystem with 8 pieces cutter1. Control box and systemTaiwan Baoyuan (LNC ) Control box and control System2. Disc Auto-tool changer—Tool Storage3. Big Germany Ball Screw。